LG Electronics LG Life Good Computer Monitor D2342P User Manual

OWNER’S MANUAL  
3D MONITOR  
Please read this manual carefully before operating the  
your set and retain it for future reference.  
3D MONITOR MODEL  
D2342P  
ASSEMBLING AND PREPARING  
3
ASSEMBLING AND PREPARING  
Unpacking  
Check your product box for the following items. If there are any missing accessories, contact the local  
dealer where you purchased your product. The illustrations in this manual may differ from the actual product  
and accessories.  
CD(Owner's Manual) /  
Card  
TriDef 3D S/W Program CD /  
Quick Installation Guide  
Power Cord  
D-SUB Cable  
(To set it up, this signal cable may  
be attached to this product before  
shipping out.)  
DVI-D Cable  
(This feature is not available in  
all countries.)  
Stand Body  
3D Glasses  
(Normal type)  
3D Glasses  
(Clip type)  
Stand Base  
CAUTION  
Do not use any pirated items to ensure the safety and product life span.  
yy  
Any damages or injuries by using pirated items are not covered by the warranty.  
yy  
NOTE  
The accessories supplied with your product may vary depending on the model.  
yy  
Product specifications or contents in this manual may be changed without prior notice due to upgrade  
yy  
of product functions.  
User must use shielded signal interface cables (RGB cable / DVI-D cable) with ferrite cores to  
yy  
maintain standard compliance for the product.  
ASSEMBLING AND PREPARING  
4
Parts and buttons  
Power Indicator  
Lighting On: Turned on  
yy  
Lighting Off: Turned off  
yy  
(Power Button)  
AC-IN  
D-SUB  
DVI-D  
HDMI  
Connection panel (See p.10)  
ASSEMBLING AND PREPARING  
5
Button  
Description  
MENU  
Accesses the main menus.(See p.13)  
OSD LOCKED/  
UNLOCKED  
This function allows you to lock the current control settings, so  
that they cannot be inadvertently changed.  
Press and hold the MENU button for several seconds.  
The message "OSD LOCKED" should appear.  
You can unlock the OSD controls at any time by pushing  
the MENU button for several seconds. The message "OSD  
UNLOCKED" should appear.  
SUPER ENERGY  
SAVING Button  
Use this button to enter SUPER ENERGY SAVING menu.For  
3D  
AUTO  
When adjusting your display settings, always press the AUTO button on the MONITOR  
SETUP OSD. (Only Analog Mode)  
If you want the best screen, set to the resolution of the below.  
The best display mode 1920 x 1080  
VOLUME (Only HDMI mode) Adjust the volume of the Monitor set.(See p.14)  
INPUT  
You can choose the input signal.  
When two input signals are connected, you can select the input signal (D-SUB/DVI)  
y
you want.  
When only one signal is connected, it is automatically detected. The default setting is  
D-SUB.  
y
EXIT  
Exit the OSD(On Screen Display).  
Turns the power on or off.  
(Power Button)  
Power Indicator  
The power indicator stays blue if the display is running  
properly (On Mode). If the display is in Sleep Mode , the  
power indicator is blinking blue.  
 
ASSEMBLING AND PREPARING  
6
Detaching the Stand Base and Body  
Setting up the Monitor set  
Place the Monitor set with the screen side  
down on a flat and cushioned surface.  
1
2
Attaching the Stand Base  
Place the Monitor set with the screen side  
down on a flat and cushioned surface.  
1
Turn the screw to the left, and then pull out the  
Stand Base from the Stand Body.  
CAUTION  
Lay a foam mat or soft protective cloth  
on the surface to protect the screen from  
damage.  
Assemble the Stand Body into the product in  
the correct direction as shown in the picture.  
Make sure you push it until you hear it “click”.  
2
Hinge Body  
Pull out the Stand Body from the Monitor set.  
3
Stand Body  
Attach the Stand Base from the set by turning  
the screw to the right with a Coin.  
3
CAUTION  
This illustration depicts the general model of  
yy  
connection. Your monitor may differ from the  
items shown in the picture.  
Do not carry the product upside down  
yy  
Stand Base  
holding only the stand base. The product  
may fall and get damaged or injure your  
foot.  
ASSEMBLING AND PREPARING  
7
Mounting on a table  
WARNING  
When you adjust the angle, do not hold the  
buttom of the Monitor set frame as shown on  
the following illustration, as may injure your  
fingers.  
Lift and tilt the Monitor set into its upright  
position on a table.  
1
Leave a 10 cm (minimum) space from the wall  
for proper ventilation.  
10 cm  
10 cm  
10 cm  
10 cm  
Do not touch or press the screen when  
adjusting the angle of the monitor.  
Connect the Power Cord to a wall outlet.  
2
NOTE  
Tilt from +15 to -5 degrees up or down to adjust  
the angle of the Monitor set to suit your view.  
- 5  
15  
Press button on the front switch panel to turn  
the power on.  
3
Front  
Rear  
CAUTION  
Disconnect the power cord first, and then move  
or install the Monitor set. Otherwise electric  
shock may occur.  
ASSEMBLING AND PREPARING  
8
Using the Kensington security system  
Mounting on a wall  
The Kensington security system connector is  
located at the back of the Monitor set. For more  
information of installation and using, refer to the  
manual supplied with the Kensington security  
system or visit http://www.kensington.com.  
For proper ventilation, allow a clearance of 10  
cm on each side and from the wall. Detailed  
installation  
instructions are available from your dealer, see the  
optional Tilt Wall Mounting Bracket Installation and  
Setup Guide.  
Connect the Kensington security system cable  
between the Monitor set and a table.  
10 cm  
10 cm  
10 cm  
10 cm  
NOTE  
If you intend to mount the Monitor set to a wall,  
attach Wall mounting interface (optional parts) to  
the back of the set.  
The Kensington security system is optional.  
You can obtain additional accessories from  
most electronics stores.  
When you install the Monitor set using the wall  
mounting interface (optional parts), attach it  
carefully so it will not drop.  
Please use VESA standard as below.  
784.8 mm (30.9 inch) and under  
yy  
* Wall Mount Pad Thickness : 2.6 mm  
Φ
* Screw : 4.0 mm x Pitch 0.7 mm x  
Length 10 mm  
787.4 mm (31.0 inch) and above  
yy  
* Please use VESA standard wall mount pad  
and screws.  
USING THE MONITOR SET  
9
Model  
D2342P  
VESA (A x B)  
75 x 75  
Standard screw  
Number of screws  
M4  
4
Wall mount bracket  
(optional)  
RW120  
CAUTION  
Disconnect the power cord first, and then  
yy  
move or install the Monitor set. Otherwise  
electric shock may occur.  
If you install the Monitor set on a ceiling or  
yy  
slanted wall, it may fall and result in severe  
injury. Use an authorized LG wall mount  
and contact the local dealer or qualified  
personnel.  
Do not over tighten the screws as this may  
yy  
cause damage to the Monitor set and void  
your warranty.  
Use the screws and wall mounts that  
yy  
meet the VESA standard. Any damages  
or injuries by misuse or using an improper  
accessory are not covered by the warranty.  
NOTE  
Use the screws that are listed on the VESA  
yy  
standard screw specifications.  
The wall mount kit includes an installation  
yy  
manual and necessary parts.  
The wall mount bracket is optional. You can  
yy  
obtain additional accessories from your local  
dealer.  
The length of screws may differ depending  
yy  
on the wall mount. Be sure to use the proper  
length.  
For more information, refer to the  
yy  
instructions supplied with the wall mount.  
USING THE MONITOR SET  
10  
USING THE MONITOR SET  
DVI-D connection  
Connecting to a PC  
Transmits the digital video signal from your PC to  
the Monitor set. Connect the PC and the Monitor  
set with the DVI cable as shown the following  
illustrations.  
Your Monitor set supports the Plug & Play*  
yy  
feature.  
*Plug & Play: The function when a PC  
recognizes a connected device that users  
connect to a PC and turn on, without device  
configuration or user intervention.  
D-SUB  
DVI-D  
HDMI  
D-SUB connection  
Transmits the analog video signal from your PC to  
the Monitor set. Connect the PC and the Monitor  
set with the supplied D-sub 15 pin signal cable as  
shown in the following illustrations.  
D-SUB  
DVI-D  
HDMI  
DVI OUT  
HDMI connection  
Transmits the digital video and audio signals from  
your PC or A/V to the Monitor set. Connect the PC  
or A/V and the Monitor set with the HDMI cable as  
shown in the following illustrations.  
RGB OUT  
NOTE  
D-SUB  
DVI-D  
HDMI  
When using a D-Sub signal input cable  
yy  
connector for Macintosh  
Mac adapter : For Apple Macintosh use, a  
yy  
separate plug adapter is needed to change  
the 15 pin high density (3 row) D-SUB VGA  
connector on the supplied cable to a 15 pin 2  
row connector.  
HDMI OUT  
HDMI OUT  
 
USING THE MONITOR SET  
11  
Self Image Setting Function  
CAUTION  
Press the power button on the front panel to turn  
the power on. When monitor power is  
turned on, the 'Self Image Setting Function' is  
executed automatically. (Only Analog Mode)  
Connect the signal  
yy  
input cable and tighten  
it by turning the screws  
clockwise.  
Do not press the screen with your finger for  
yy  
a long time as this may result in temporary  
distortion on the screen.  
Avoid displaying a fixed image on the  
yy  
screen for a long period of time to prevent  
image burn. Use a screensaver if possible.  
NOTE  
NOTE  
‘ Self Image Setting Function’? This  
yy  
This is a simplified representation of the rear  
yy  
function provides the user with optimal  
display settings.When the user connects  
the monitor for the first time, this function  
automatically adjusts the display to optimal  
settings for individual input signals.(Only  
Analog Mode)  
view.  
This rear view represents a general model;  
yy  
your display may differ from the view as  
shown.  
If you turn the Monitor set on when the set  
yy  
becomes cold, the screen may flicker. This  
is normal.  
Some red, green, or blue spots may appear  
yy  
‘AUTO’ Function? When you encounter  
yy  
problems such as blurry screen, blurred  
letters, screen flicker or tilted screen while  
using the device or after changing screen  
resolution, press the AUTO function button to  
improve resolution.(Only Analog Mode)  
on the screen. This is normal.  
CUSTOMIZING SETTINGS  
12  
CUSTOMIZING SETTINGS  
Accessing main menus  
Press any button on the front of the Monitor set to display the MONITOR SETUP OSD menu.  
1
2
3
Press to select the desired menu item.  
Change the value of the menu item by pressing the buttons on the front of the Monitor set.  
To return to the upper menu or set other menu items, use the up arrow ( ) button  
Select EXIT to leave the OSD menu.  
4
onitor set button  
M
Sets the screen options.  
Optimizes the resolution.  
EXIT  
Exits the OSD menu.  
MONITOR SETUP  
MENU  
3D  
AUTO  
VOLUME  
INPUT  
EXIT  
INPUT  
Sets the 3D mode.  
Sets the volume.  
Sets the external input.  
NOTE  
Different menu items are enabled depending on the type of input signal.  
D-SUB Mode: MENU, 3D, AUTO, INPUT, EXIT  
yy  
HDMI Mode: MENU, 3D, VOLUME, INPUT, EXIT  
yy  
CUSTOMIZING SETTINGS  
13  
Customizing settings  
Mnue settings  
MENU  
BRIGHTNESS  
100  
Press any button on the front of the Monitor set to display the  
MONITOR SETUP OSD menu.  
1
2
3
4
ORIGINAL RATIO  
COLOR TEMP  
PRESET  
RED  
GREEN  
WIDE  
PRESET  
WARM  
Press the MENU button to display the options in the OSD  
menu.  
50  
50  
50  
70  
BLUE  
Set the options by pressing the buttons on the front of the  
Monitor set.  
CONTRAST  
BLACK LEVEL  
LANGUAGE  
SUPERENEYGYSAVING  
FACTORY RESET  
HIGH  
ENGLISH  
Select EXIT to leave the OSD menu.  
To return to the upper menu or set other menu items, use the  
up arrow ( ) button  
NO  
EXIT  
The available Programme settings are described in the following:  
Menu  
Analog Digital  
HDMI  
Description  
BRIGHTNESS  
To adjust the brightnesTo adjust the brightness of the screen.s of  
the screen.  
ORIGINAL RATIO  
COLOR TEMP  
WIDE  
Switch to full screen mode according to input image signal.  
ORIGINAL  
XXXXX  
* XXXXXX  
PRESET  
Select the screen color.  
WARM: Set the screen to warm color temperature .  
MEDIUM: Set the screen to medium color temperature.  
COOL: Set the screen to cool color temperature.  
y
y
y
USER  
RED: Set your own red color levels.  
GREEN: Set your own green color levels.  
BLUE: Set your own blue color levels.  
y
y
y
CONTRAST  
To adjust the contrast of the screen.  
BLACK LEVEL  
(Only HDMI mode)  
You can set the offset level. If you select 'HIGH', the screen will be  
bright and if you select ‘LOW’, the screen will be dark.  
Offset  
y
As the criteria for video signal, it is the darkest screen the  
monitor can show.  
LANGUAGE  
To choose the language in which the control names are displayed.  
Sets the SUPER ENERGY SAVING function.  
SUPER ENEYGY  
SAVING  
FACTORY  
The first screen of the Monitor set at the time of purchase to return  
to the state. However, the language menu is not initialized.  
Analog: D-SUB(Analog signal) input.  
yy  
Digital: DVI-D(Digital signal) input.  
yy  
HDMI: HDMI(Digital signal) input.v  
yy  
   
CUSTOMIZING SETTINGS  
14  
3D  
3D settings(Only 3D mode)  
3D MODE  
OFF(1/4)  
R-L(1/2)  
OFF  
3D L/R CHANGE  
3D - > 2D  
Press any button on the front of the Monitor set to display the  
MONITOR SETUP OSD menu.  
1
Press the 3D button to display the options in the OSD menu.  
2
3
EXIT  
Set the options by pressing the buttons on the front of the  
Monitor set.  
Select EXIT to leave the OSD menu.  
4
To return to the upper menu or set other menu items, use the  
up arrow ( ) button  
The available picture settings are described in the following:  
Menu  
3D MODE  
Description  
Sets the format of the input data.(Enabled only for HDMI VIDEO TIMING)  
SIDE BY SIDE  
TOP & BOTTOM  
LINE INTERLACED  
OFF  
Splits the screen vertically and displays the left and right 3D images  
on the left and right of the screen.  
Splits the screen horizontally and displays the left and right 3D images  
on the top and bottom of the screen.  
Splits the screen into lines and displays 3D data by interlacing the left  
and right images.  
Displays 3D data on the screen.  
3D L/R CHANGE  
3D - > 2D  
Sets in which order to display the 3D images.  
R-L  
L-R  
Displays the 3D images right to left.  
Displays the 3D images left to right.  
Converts 3D images into 2D. (enabled only for HDMI VIDEO TIMING)  
OFF  
ON  
Displays images in 3D.  
Displays images in 2D.  
NOTE  
If the 3D option selected is incorrect, images may not be displayed properly.  
VOLUME  
VOLUME settings(Only HDMI mode)  
Press any button on the front of the Monitor set to display the  
MONITOR SETUP OSD menu.  
1
2
3
4
Press the VOLUME button to display the options in the OSD  
menu.  
EXIT  
Set the options by pressing the buttons on the front of the Monitor  
set.  
Select EXIT to leave the OSD menu.  
To return to the upper menu or set other menu items, use the up  
arrow ( ) button  
   
CUSTOMIZING SETTINGS  
15  
SUPER ENERGY SAVING settings  
SUPER ENERGY SAVING  
Press any button on the front of the Monitor set to display  
the MONITOR SETUP OSD menu.  
1
2
3
4
ON  
OFF  
RESET  
Press the MENU button to display the options in the OSD  
menu.  
SUPER  
SAVING  
:5W/h  
TOTAL POWER REDUCTION: 20 W  
TOTAL CO2 REDUCTION: 16 g  
LED  
Select SUPER ENERGY SAVING by pressing the buttons  
on the front of the Monitor set and set the options.  
SAVING  
:12W/h  
Select EXIT to leave the OSD menu.  
OK  
EXIT  
To return to the upper menu or set other menu items, use  
the up arrow ( ) button  
The available picture settings are described in the following:  
Menu  
Description  
ON  
Enables SUPER ENERGY SAVING; you can save energy with this energy-efficient function.  
Disables SUPER ENERGY SAVING.  
OFF  
RESET  
Resets the values of total energy consumption reduction and CO2 emission reduction.  
NOTE  
TOTAL POWER REDUCTION: How much power is saved during using the monitor.  
yy  
TOTAL CO2 REDUCTION: Change the TOTAL POWER REDUCTION to CO2.  
yy  
SAVING DATA(W/h)  
yy  
584 mm (23 inch)  
SUPER SAVING  
LED SAVING  
5
12  
Saving Data depends on the Panel. So,those values should be different from each panel and  
yy  
panel vendor.  
LG accumulate those values using integrated function with 10 minutes "broadcast video  
yy  
signal".  
LED Saving means that how much power can be saved using WLED Panel instead of CCFL  
yy  
panel.  
SUPER Saving means that how much power can be more saved using SUPER ENERGY  
yy  
SAVING function.  
 
TROUBLESHOOTING  
16  
TROUBLESHOOTING  
Check the following before calling for service.  
No image appears  
Is the power cord of the display  
connected?  
Check and see if the power cord is connected properly to the power  
outlet.  
y
Is the power indicator light on?  
Press the Power button.  
y
y
Is the power on and the power  
indicator blue or green?  
Adjust the brightness and the contrast.  
Is the power indicator flickering?  
If the display is in power saving mode, try moving the mouse or  
pressing any key on the keyboard to bring up the screen.  
Try to turn on the PC.  
y
y
y
Do you see an "OUT OF RANGE"  
message on the screen?  
This message appears when the signal from the PC (video card) is  
out of horizontal or vertical frequency range of the display. See the  
'Specifications' section of this manual and configure your display  
again.  
Do you see a "CHECK SIGNAL  
CABLE" message on the screen?  
This message appears when the signal cable  
between your PC and your display is not  
connected. Check the signal cable and try again.  
y
y
y
Do you see a "OSD LOCKED" message on the screen?  
Do you see “OSD LOCKED” when  
you push MENU button?  
You can secure the current control settings, so that they cannot be  
inadvertently changed. You can unlock the OSD controls at any time  
by pushing the MENU button for several seconds: the message  
“OSD UNLOCKED” will appear.  
y
y
y
Display image is incorrect  
Display Position is incorrect.  
Press the AUTO/SET button to automatically adjust your display  
image to the ideal setting. If the results are unsatisfactory, adjust the  
image position using the H position and V position icon in the on  
screen display.  
On the screen background, vertical  
bars or stripes are visible.  
Press the AUTO/SET button to automatically adjust your display  
image to the ideal setting. If the results are unsatisfactory, decrease  
the vertical bars or stripes using the CLOCK icon in the on screen  
display.  
y
Any horizontal noise appearing in  
any image or characters are not  
clearly portrayed.  
Press the AUTO/SET button to automatically adjust your display  
image to the ideal setting. If the results are unsatisfactory, decrease  
the horizontal bars using the PHASE icon in the on screen display.  
Check Control Panel ► Display ► Settings and adjust the display to  
the recommended resolution or adjust the display image to the ideal  
setting. Set the color setting higher than 24 bits (Color Quality).  
y
y
CAUTION  
Check Control Panel ► Display ► Settings and see if the frequency or the resolution were changed.  
yy  
If yes, readjust the video card to the recommend resolution.  
If the recommended resolution (optimal resolution) is not selected, letters may be blurred and the  
yy  
screen may be dimmed, truncated or biased. Make sure to select the recommend resolution.  
The setting method can differ by computer and O/S (Operation System), and resolution mentioned  
yy  
above may not be supported by the video card performance. In this case, please ask to the computer  
or the video card manufacturer.  
TROUBLESHOOTING  
17  
Display image is incorrect  
The screen color is mono or  
abnormal.  
Check if the signal cable is properly connected and use a screwdriver  
to fasten if necessary.  
y
Make sure the video card is properly inserted in the slot.  
Set the color setting higher than 24 bits (Color Quality) at Control  
Panel Settings.  
y
y
The screen blinks.  
Check if the screen is set to interlace mode and if yes, change it to the  
recommend resolution.  
y
Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message?  
Have you installed the display  
driver?  
Be sure to install the display driver from the display driver CD (or  
diskette) that comes with your display. Or, you can also download the  
y
Make sure to check if the video card supports Plug&Play function.  
y
TROUBLESHOOTING WHEN USING 3D MODE  
I can see a swirling oil-like pattern on the monitor when the monitor is turned off.  
This is caused by the interference of external light in the air layer between the LCD surface and 3D filter.  
The pattern becomes almost invisible when you turn on the power again.  
y
IN coa nimnoagt es eaep 3pDea rims ages properly.  
If you are not using the glasses  
provided with the monitor,  
When you view 3D images with this monitor, it is very important  
that you use the glasses provided with the monitor. The glasses are  
designed to compensate optically for the 3D filter attached to the  
surface of the monitor. If you wear third-party glasses, you may not  
see 3D images properly on the monitor.  
y
y
If you view 3D images outside the  
optimal viewing angle or distance,  
The optimal viewing angle of this monitor is between -4° to 8°  
degrees; the optimal viewing distance is between 50 cm to 70 cm from  
the monitor. When you view 3D images outside the optimal viewing  
angle or viewing distance, the images may look overlapped or not be  
displayed properly in 3D.  
If you have not set the resolution,  
Please set the resolution of the monitor to the maximum (1920 x  
1080 @ 60 Hz) in the display settings. The 3D software may not work  
properly if the resolution is not set to the maximum.  
y
y
If the images that your left and right  
eyes see are reversed,  
The stripe images in the odd-numbered lines are the ones that your  
right eye sees on the monitor. If you only see the stripe images, not  
3D images, set the images for your right eye to be displayed in the  
odd-numbered lines by changing the player or viewer option of the 3D  
software.  
I cannot see 3D but only 2D images.  
This monitor works both in 2D and 3D mode. You can view a video in  
3D if it is made in 3D. If you try to view 2D images in 3D, they might  
not be displayed properly or you may experience poor picture quality.  
y
SPECIFICATIONS  
18  
SPECIFICATIONS  
D2342P  
Display  
Screen Type  
584 mm (23 inch) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Visible diagonal size: 584 mm  
Pixel Pitch  
0.265 mm x 0.265 mm (Pixel Pitch)  
30 kHz to 83 kHz (Automatic)  
Sync Input  
Horizontal Frequency  
Vertical Frequency  
56Hz to 75Hz (D-Sub, DVI-D)  
56Hz to 61Hz (HDMI)  
Input Form  
Signal Input  
Separate Sync. Digital  
Video Input  
Resolution  
15 pin D-SUB Connector /DVI-D Connector (Digital)  
HDMI Connector  
Input Form  
Max  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
D-Sub(Analog) : 1920 x 1080 @ 60 Hz  
DVI / HDMI (Digital) : 1920 x 1080 @ 60 Hz  
Recommend  
VESA 1920 x 1080 @ 60 Hz  
Plug & Play  
DDC 2B(Analog,Digital)  
Power Consumption  
On Mode : 39 W(Typ.)  
Sleep Mode ≤ 0.5 W  
Off Mode ≤ 0.5 W  
Power Input  
AC 100-240 V~ 50 / 60 Hz 1.2A  
Dimensions  
(Width x Height x Depth)  
With Stand  
Without Stand  
3.5 kg  
546 mm x 407 mm x 202 mm  
546 mm x 342 mm x 57 mm  
Weight  
Tilt Rangew  
-5° to 15°  
Environmental  
conditions  
Operating Temperature 10°C to 35 °C  
Operating Humidity  
20 % to 80 %  
Storage Temperature  
Storage Humidity  
-10°C to 60 °C  
5 % to 90 % non-Condensing  
Stand Base  
Power cord  
Attached ( ), Detached (O)  
Wall-outlet type  
Product specifications shown above may be changed without prior notice due to upgrade of product  
functions.  
SPECIFICATIONS  
19  
Preset Modes (Resolution)  
Horizontal  
Display Modes (Resolution)  
Frequency(kHz)  
Vertical  
Frequency(Hz)  
Polarity(H/V)  
720 x 400  
31.468  
31.469  
37.500  
37.879  
46.875  
48.363  
60.123  
67.500  
63.981  
79.976  
65.290  
67.500  
70  
60  
75  
60  
75  
60  
75  
75  
60  
75  
60  
60  
-/+  
-/-  
640 x 480  
640 x 480  
-/-  
800 x 600  
+/+  
+/+  
-/-  
800 x 600  
1024 x 768  
1024 x 768  
1152 x 864  
1280 x 1024  
1280 x 1024  
1680 x 1050  
1920 x 1080  
+/+  
+/+  
+/+  
+/+  
-/+  
+/+  
Recommend Mode  
HDMI 3D TIMING  
3D Format  
Resolution  
1080 p  
720 p  
Refresh Rate  
Limitation  
Frame Packing  
Frame Packing  
Side-by-Side(Half)  
Side-by-Side(Half)  
Side-by-Side(Half)  
Top-and-Bottom  
Top-and-Bottom  
Top-and-Bottom  
24 Hz  
50/60 Hz  
50/60 Hz  
50/60 Hz  
50/60 Hz  
50/60 Hz  
24 Hz  
1080 p  
1080 i  
720 p  
1080 p  
1080 p  
720 p  
50/60 Hz  
Indicator  
Mode  
LED Color  
On Mode  
Sleep Mode  
Off Mode  
Blue  
Blue Color Blinking  
Off  
XXXXX  
20  
PRECAUTIONS TO TAKE WHEN VIEWING 3D  
IMAGES  
If you view images in the 3D mode for a long period of time (playing games, watching movies etc.), you  
may feel dizzy. We strongly recommend you to take a rest after viewing images in 3D mode for one  
hour. (The time of experiencing dizziness varies depending on the individual.)  
1
Please view 3D images at the optimal viewing angle and at the recommended distance from the  
product. Otherwise, 3D images may appear to be overlapped or may not be displayed properly.  
2
3
4
5
6
7
8
If you view 3D images too closely for a long period of time, this may result in dizziness or blurred vision.  
Please use the device at the recommended distance.  
If you are pregnant, elderly or have heart problems, we recommend that you do not view 3D images.  
This is because the 3D images can cause disorientation and confusion.  
3D images can also cause nausea or vomiting for users under the influence of alcohol. In this situation,  
please do not view 3D images.  
Parents/guardians should monitor children’s viewing of 3D images because they may not be used to the  
3D viewing experience and lack knowledge on how to handle potential risks.  
Do not use the 3D glasses as regular glasses, sunglasses or goggles. This may cause your vision to  
worsen.  
Do not keep the 3D glasses in an extremely hot or cold place. This may the shape of the glasses to  
change and become damaged. Do not use the 3D glasses if they are damaged because this may cause  
your vision to worsen, or you may experience dizzin  
The lenses of the 3D glasses (polarizing film) are easily scratched. Use a soft clean cloth when cleaning  
them. Do not use any chemical cleaning products on the glasse  
9
CAUTION  
Warning about photosensitivity seizures  
Some users may have a seizure or other abnormal symptoms when they are exposed to a  
yy  
flashing light or particular pattern in a video game or movie. If anyone in your family has a history  
of epilepsy or has ever experienced any kind of seizure, please consult with your doctor before  
viewing 3D images. If you exhibit any of the symptoms listed below when viewing 3D images,  
please stop viewing immediately and consult with your doctor even if you do not have previous  
medical problems of this nature.  
Symptoms  
Dizziness, blurred vision or facial tics, involuntary movements, twitching, blackouts, confusion,  
yy  
disorientation and wrong state.  
To prevent a photosensitivity seizure, please follow the instructions below.  
Do not view 3D images when you are tired or ill.  
yy  
Do not view 3D images for a long period of time.  
yy  
Reduce the depth of the 3D image.  
yy  
XXXX  
21  
PROPER POSTURE  
Proper posture for using the Monitor set.  
Adjust your distance from the Monitor  
set to allow you to view images from  
the optimal distance (L).  
60 cm  
Adjust the  
Monitor set and  
your posture to  
allow you to view  
images at the  
optimal viewing  
angle (D).  
Adjust the location of the  
Monitor set to avoid it  
reflecting light.  
90°  
Place your hands  
gently on the  
keyboard, keeping  
your arms bent at  
the elbows and  
horizontally outright.  
Mode  
Size(Inch)  
584 mm  
Optimal viewing distance (L) Optimal viewing angle (D)  
When viewing 3D images  
50 cm to 70 cm  
-4° to 8°  
Precautions to take when viewing 3D images  
Wear the 3D glasses provided with the Monitor set.  
yy  
Watch your posture.  
yy  
Remain at the optimal distance and angle when viewing 3D images.  
yy  
(Viewing 3D images too closely may cause your vision to worsen, or you may experience dizziness.)  
Make sure to read the Safety Precautions before  
using the product.  
Keep the Owner’s Manual (CD) in an accessible  
place for future reference.  
The model and serial number of the SET is  
located on the back and one side of the SET.  
Record it below should you ever need service.  
ENERGY STAR is a set of power-saving  
guidelines issued by the U.S.Environmental  
Protection Agency(EPA).  
As an ENERGY STAR Partner LGE  
U. S. A.,Inc. has determined that this  
product meets the ENERGY STAR  
guidelines for energy efficiency.  
MODEL  
SERIAL  

Intel AW8D User Manual
Intel Computer Hardware 845GL User Manual
Intel RES2SV240 User Manual
JVC AV 29QH4BU User Manual
KitchenAid KECC507GWH1 User Manual
KitchenAid KECS100 User Manual
KitchenAid KGCT305G User Manual 1
Mitsubishi Electronics 1770G User Manual
Philips BDS4622V User Manual
Philips LX3700D User Manual