SERVICE MANUAL
™
TOP-SIDE
COOKER
1-800-KEATING
T1
T2
SET
T3
WATLOW
CV
WATLOW
CV
ELEMENT
°F
ON
ELEMENT
°F
ON
°C
°C
LOAD
LOAD
PUSH
PUSH
TO SET
TO SET
ON
OFF
ON
OFF
Keating of Chicago, Inc.
1-800-KEATING
KEEP THIS MANUAL FOR TRAINING NEW PERSONNEL
028951
Top Side 0107
09/07
i NOTICE: This operating, installation, and service manual should be given to the user. The operator of the Top-
™
Side Cooker should be familiar with its functions and operation. This manual must be kept in a prominent, easily
™
reachable location near the Top-Side Cooker .
i NOTICE: Keating of Chicago, Inc. (manufacturer) reserves the right to change specifications at any time.
WARNING
WARNING
DO NOT STORE OR USE GASOLINE
OR OTHER FLAMMABLE VAPORS
OR LIQUIDS IN THE VICINITY OF THIS
OR ANY OTHER APPLIANCE.
Do not store flammable
liquids near this or any
other appliance.
WARNING
WARNING
IMPROPER
INSTALLATION,
ALTERATION,
ADJUSTMENT,
SERVICE OR MAINTENANCE CAN
CAUSE
PROPERTY
DAMAGE,
INJURY OR DEATH. READ THE
INSTALLATION, OPERATING AND
MAINTENANCE
INSTRUCTIONS
THOROUGHLY BEFORE INSTALLING
OR SERVICING THIS EQUIPMENT.
Improper installation
can cause damage,
injury or death.
WARNING
WARNING
BEFORE OBTAINING ACCESS TO
TERMINALS, ALL SUPPLY CIRCUITS
MUST BE DISCONNECTED.
Disconnect all power
before servicing.
ii
SAFETY
PRECAUTIONS
I INTRODUCTION
WARNING
THIS SYMBOL WARNS YOU THAT SERIOUS
BURNS OR OTHER INJURIES MAY RESULT IF
SAFETY INSTRUCTIONS ARE NOT FOLLOWED.
GENERAL
™
Keating Top-Side Cookers are designed to give
maximum production efficiency, delivering high quality
food products. The following design features are
™
incorporated into Keating Top-Side Cookers.
™
l DO NOT SUBMERGE THE TOP-SIDE COOKING
HEAD IN WATER.
STANDARD
FEATURES
l Stainless steel control panel
l Stainless steel head cover
l MIRACLEAN cooking surface
l CLEANING CHEMICALS OR UTENSILS USED
FOR CLEANING GRIDDLES WILL DAMAGE OR
DESTROY THE POLYMER COOKING SHEET.
l NEVER USE A WATER JET TO CLEAN.
®
l Solid State Thermostat
l Adjustable cooking height, from /8'' to 1 / '' (3mm to
1
1
2
II INSTALLATION
38mm)
™
This Top-Side Cooker MUST be installed on a Keating
griddle only. Failure to do so voids the warranty.
l Locking mechanism for micro-level
™
The Top-Side Cooker must be installed, inspected,
STANDARD
calibrated and serviced by qualified, certified and/or
licensed service personnel. Contact your dealer for
assistance.
ACCESSORIES
l Proprietary USDA and UL listed polymer cooking
sheets (1)
DAMAGE DURING
SHIPMENT
¥¥
NOTE: Keating of Chicago, Inc. (manufacturer)
reserves the right to change specifications at any time.
™
The Top-Side Cooker has been assembled, tested and
inspected at the factory. Upon arrival, the complete Top-
COOKING HEAD
SPECIFICATIONS
Each Top-Side cooking head is designed to be
connected to a 208, 220 or 240 volt single phase line.
™
Side Cooker should be thoroughly checked for any
damage that may have occurred during shipment.
TM
What to do if equipment arrives damaged:
HEIGHT WIDTH
DEPTH WATTS
20" 4,000
AMPS
18
@220V
kW
VISIBLE LOSS OR DAMAGE- Be certain to note this on
the freight or express receipt and have it signed by the
delivery person.
5
1
3 /
8
"
10 /2"
4.8
(92mm) (267mm) (508mm) @220V
FILE CLAIM FOR DAMAGES IMMEDIATELY-
Regardless of extent of damage.
STANDARD
TOP-SIDE™
COOKERS
CONCEALED LOSS OR DAMAGE- If the damage is
noticed when the equipment is unpacked, notify the
freight company immediately, and file a “concealed
damage claim”. This MUST be done immediately. Be
sure to retain the shipping container for inspection.
l Sizes: 1 to 6 heads.
l Mounting: Can be mounted to any standard
®
MIRACLEAN gas or electric 30'' (762mm) deep
griddle (24'' deep plate / 610mm) up to 72" wide (up to
6 heads maximum). Front trough only griddles are
preferred for multiple heads.
Keating does not assume responsibility for loss OR
damage incurred in transit.
1
2
l Cooking Surface: 10 / '' (267mm) wide x 20'' (508mm)
deep (per cooking head).
INSTALLATION
l Number of heads: One head can be used for every 12''
™
™
On new installations, your Top-Side Cooker has already been
(305mm) of plate width. Each Top-Side cooking head
™
factory installed, tested leveled and inspected. Top-Side
will be positioned over a griddle thermostat to ensure
peak efficiency.
®
Cookers cannot be mounted onto existing Miraclean griddles.
l ETL and ETL Sanitation listed.
1
Clockwise movement of the knob will decrease the
spacing; counter clockwise movement will increase the
spacing. Each turn of the adjusting knob represents
1/8'' (approximately 3mm) movement.
ELECTRICAL
CONNECTION
™
Each Keating Top-Side Cooking head is equipped
with a 9' (2.74m) neoprene covered, 12 gauge 4mm(2),
three wire with ground electrical cord. Each cooking
head is rated 4000W, 18 amps, single phase at 220
Volts and is designed to be connected to its own 208-
240V single phase electrical supply. For proper
connecting and grounding procedure see local codes,
the National Electrical Code ANSI/NFPA 70 (latest
edition) or Canadian Electrical Code CAN C22.1 (latest
edition) as applicable.
Experimentation will give you the best cooking height
for each type of food product. The cooking head should
contact the product firmly to ensure optimum heat
distribution without flattening the product.
SHUTDOWN
Turn ON/OFF switch to “OFF” position.
CLEANING
PROCEDURES
WARNING
A. Keating Cooking Sheets
THIS APPLIANCE MUST BE EARTHED.
l Clean cooking sheets with a damp soft cloth after
each run of product (a Turkish towel works best).
III OPERATING
CAUTION
Food will cook much faster with a Top-Side Cooker
than with a griddle alone. Watch food while cooking or
use timers to ensure food will not be overcooked.
WARNING
THE COOKING HEAD WILL BE HOT. USE PROPER
CARE WHEN CLEANING THE COOKING SHEETS.
™
End of day cleaning:
Before the griddle is turned off for the day, the cooking
sheets should be cleaned as described below. Wear
heat resistant gloves for maximum safety during the
entire cleaning procedure.
WARNING
™
OPERATION OF THE TOP-SIDE
COOKER
PERSONNEL
OPERATING
SHOULD
BE
LIMITED
TRAINED
TO
IN
1. At the end of the day, wipe the cooking sheet in
place with a damp soft cloth. Continue wiping until
the surface of the cooking sheet is free of any
residue.
THOROUGHLY
PROCEDURES.
COOKING
2. Remove the cooking sheet from the cooking head.
Clean the cooking head and the griddle surfaces.
1. Turn ON/OFF switch to “ON” position.
2. Press and hold the “Push to Set” button on the
thermostat and adjust the knob to the desired
temperature. The new temperature will be entered
after 3 seconds. Red “ELEMENT ON” light will
illuminate when the element is on.
3. Wash the cooking sheet with a mild detergent in
warm water and dry thoroughly.
4. If needed, after the cleaning is complete, reverse
the cooking sheet and reattach it to the cooking
head.
Figure 3-1
TM
Top-Side Cooker Control Panel
B. Cooking Sheet Clips
To remove the stainless steel cooking sheet clips for
cleaning, simply lift them off. They can be cleaned in a
dishwasher.
C. Cooking Head
®
The MIRACLEAN surface is very durable and with
proper care, following the procedures below, will last
many years.
®
1. Scrape MIRACLEAN surface from front to back
COOKING HEIGHT
ADJUSTMENT
with the Keating griddle scraper with Cooking
Sheets removed.
™
Keating’s Top-Side Cooker has been designed to
1
1
2
allow you infinite height adjustments from /8'' to 1 / ''
(approximately 3mm to 38mm). An adjusting knob
allows fast and precise height adjustment.
2. Clean and polish surface with certified Keating
Klenzer on a damp soft cotton cloth. Wipe off
excess Klenzer.
2
WARNING
IV MAINTENANCE
®
BECAUSE OF THE SUPERIOR MIRACLEAN
SURFACE, THE ONLY TOOLS YOU WILL EVER NEED
™
TO CLEAN THE TOP-SIDE COOKING HEAD ARE A
WARRANTY REPAIRS
Keating’s warranty begins with the date of installation.
In the event your Keating Top-Side Cooker needs
repair under warranty other than routine maintenance
or cleaning you are requested to contact KEATING OF
CHICAGO, INC. at 1-800-KEATING before calling a
local service company.
DAMP SOFT COTTON CLOTH AND A KEATING
SCRAPER.
™
l NEVER SCRAPE COOKING SHEETS WITH THE
SCRAPER.
l NEVER USE A GRIDDLE STONE, BRICK,
GRIDDLE SCREEN OR HARSH CHEMICALS TO
®
CLEAN THE MIRACLEAN SURFACE.
¥¥ NOTE: The cooking sheets are not covered under
warranty.
®
l DAMAGE DONE TO THE MIRACLEAN SURFACE
BY GRIDDLE STONE, BRICK, SCREEN, OR
HARSH CHEMICALS WILL VOID THE WARRANTY.
PREVENTIVE
MAINTENANCE
®
l THE DAMAGE DONE TO THE MIRACLEAN
SURFACE IS IRREPARABLE.
Preventive maintenance should be done in daily,
weekly, monthly and yearly intervals as necessary.
Following preventive maintenance procedures will help
®
l NEVER USE ICE TO COOL THE MIRACLEAN
®
SURFACE AS IT MAY WARP THE MIRACLEAN
SURFACE.
™
keep your Top-Side Cooker working efficiently. Proper
l USE ONLY KEATING SUPPLIED CLEANING
care and servicing will lead to years of quality
performance.
TOOLS AND KLENZER.
l USE ONLY A KEATING STEEL SPATULA.
TIME
OPERATOR/OWNER
SECTION
FRAME
CAUTION
At Least
Daily
• Clean all cooking sheets.
• Clean MIRACLEAN Griddle
surface.
III
Do not hack, chop or hit the surface. You will dent the
steel plate under the trivalent chrome. It is even
possible to hack two nicks close together and actually
®
®
tear the MIRACLEAN surface as the chromium will not
At Least
Weekly*
• Clean all surfaces of
Top-Side Cooker.
III
™
stretch. Below is a sketch showing a side view of a
cooking had and how the surface can be damaged.
Proper use of the utensils supplied with your
Monthly*
• Verify thermostat settings.
• Review cooking procedures.
IV & V
III
®
MIRACLEAN Griddle will prevent surface damage.
• Check Cooking Sheets
(Replace if necessary).
Surface Damage
At Least
Yearly*
QUALIFIED SERVICE
PERSONNEL ONLY
IV & V
• Thoroughly check and test
™
Top-Side Cooker.
• Calibrate controls.
*High production facilities should be checked more often.
Contact the factory or a local service company to perform
maintenance and repairs.
Proper care should be taken to fully clean the Top-
™
Side Cooker on a regular basis. The control panel
should be cleaned of any greasy residue with a damp
cotton cloth. Remove any residue from the ON/OFF
switch and the thermostat. Wipe down the cabinet,
sides and back on a regular basis.
3
INSTALLING A
LEVELING OF
COOKING SHEET
COOKING HEAD(S)
™
1. Raise Top-Side Cooking head completely.
The cooking head(s) were leveled at the factory.
2. Lay the 20'' x 24'' (508mm x 610mm) cooking sheet
on the griddle plate with 20'' (508mm) dimension
front to back.
¥¥ NOTE: For best results, level griddle before
checking. Adjust legs or stand casters to level griddle.
™
REMOVAL OF
3. Lower the Top-Side Cooker head onto the
COOKING HEAD
cooking sheet, ensuring that the sheet is centered
under the head, the front edge of the sheet is even
with the front edge of the head, and the sides of the
sheet are parallel to the side of the head.
¥¥ NOTE: To identify parts, refer to page 7.
™
1. Turn off griddle and disconnect Top-Side Cooker
electric power.
4. Fold both edges of the cooking sheet over the
head. While gently pulling the right side of the
sheet to remove any slack, firmly push the cooking
sheet mounting clip onto the right side mounting rib
on top of the head.
2. Remove the cooking sheet by lifting off cooking
sheet mounting clips.
3. Place a layer of soft cloth and then a layer of
cardboard onto griddle plate under cooking head to
®
protect MIRACLEAN surface.
5. Repeat process on the left side.
6. Reverse the process to remove the cooking sheet.
4. Raise cooking head completely to release tension
on cooking head support pin. Remove support pin
and its cotter pin and carefully lower cooking head
to protected griddle surface.
TIPS ON PROPER
HANDLING AND USE
OF COOKING SHEETS
WARNING
To ensure long life of your Keating cooking sheets
please follow the tips below:
The cooking head is not supported after the
cooking head support pin has been removed. If
dropped the weight of the cooking head when
unsupported will cause damage to the griddle
surface or injury to personnel.
Cooking sheets should never:
l Be folded or creased.
l Be touched with sharp objects.
5. Do not turn the support pin in either direction.
l Come in contact with griddle scrapers or abrasive pads.
l Be placed under other equipment or objects.
Cooking sheets should always:
6. To reattach the cooking head to the ram lift arm,
raise cooking head completely and replace
cooking head support pin. Insert a new stainless
steel cotter pin to secure support pin, holding
support pin to keep it from spinning.
l Be wiped with a damp soft cotton cloth after each run
to remove any product residue.
7. Replace cooking sheet. See - “Installing a Cooking
Sheet”.
l Be cleaned after the griddle is shut down for the day.
The time to change a Cooking Sheet is when:
l Product starts sticking to the sheet.
l Too much carbon build-up causes a product
appearance, cooking or taste problem.
l The head surface is cool.
l The sheet is torn or ripped.
WARNING
™
THE TOP-SIDE COOKING HEAD AND GRIDDLE
PLATE ARE HOT - USE PROPER CARE WHEN
CHANGING THE COOKING SHEETS.
4
V SERVICE DIAGNOSIS
™
A properly adjusted Keating Top-Side Cooker, with no
1
1
2
2
load, will cycle “ON” approximately every 5 / to 6 /
minutes. Each cycle will last 40 seconds, ensuring that
the temperature setting is held within a narrow range.
A. Trouble-Shooting
The following diagnosis is only to be used as a guide to
qualified service personnel. Keating recommends that
you use a qualified service company.
WARNING
Disconnect power before servicing.
PROBLEM
PROBABLE CAUSE
SOLUTION
™
™
POWER ON light does not a.No electricity to Top-Side Cooker.
come on.
a.Connect Top-Side Cooker to an
approved source of power.
b.Replace ON/OFF SWITCH
b.ON/OFF switch is faulty.
ELEMENT ON light does not a.Connections to thermostat are loose a.Check connections and tighten where
come on and cooking head
will not heat.
or thermostat is faulty.
necessary. If thermostat is faulty,
replace.
b.Connections to
temperature probe are loose or probe
is faulty.
c.Hi-Limit has tripped or Hi-Limit is c.Wait until cooking head cools down. If
faulty. Note: Hi-Limit is self-resetting.
thermostat b.Check connections and tighten where
necessary. If probe is faulty, replace it.
ELEMENT ON light will not come on
Hi-Limit is faulty, replace it.
d.Connections to Hi-Limit are loose or d.Check connections and tighten where
Hi-Limit is faulty.
necessary.
e.Connections to contactor are loose or e.Check connections and tighten where
contactor is faulty.
necessary. If contactor is faulty,
replace it.
f. Replace ON/OFF switch.
f. ON/OFF switch is faulty.
ELEMENT ON light does not a.ELEMENT ON light is faulty.
come on, but cooking head
does heat.
a.Replace ELEMENT ON light.
ELEMENT ON light flashes a.Thermostat temperature probe or a.Replace probe and/or wires. Use
once whenever power is
turned on.
wires have shorted out.
conductive heat paste when installing
new probe.
Temperature of cooking head a.If erratic, thermostat is faulty.
is erratic.
a.Replace thermostat.
5
TROUBLESHOOTING THE THERMOSTAT
Temperature reading is incorrect,
showing a sensor error,
LOAD LED is switching at the
wrong temperature.
• Sensor or controller may be bad. Place a jumper wire across the
or Sensor connections may be bad.
thermocouple input terminals. The
display should indicate ambient
temperature. If it does, the
controller is ok. If not, replace
controller.
Decrease set point below ambient
temperature, LOAD LED should be
off for heating controllers. If it is, the
controller is OK.
Increase set point above ambient
temperature. LOAD LED should be
on for heating controllers. If it is, the
controller is OK.
• Controller is wired incorrectly.
Verify proper wiring. Call 1-800-
KEATING for a diagram.
• Thermocouple polarity is reversed. Check thermocouple connections.
Temperature reading is decreasing,
but actual temperature is increasing.
Red wire denotes negative wire.
All connections, including extension
wire, must maintain the correct
polarity. Correct if needed.
• Ambient temperature in the control Measure temperature in cabinet to
cabinet is over 70°C. ensure it is below 70°C.
For troubleshooting the thermocouple, use the chart below
Temperature (°F) Resistance (Ohm)
95
0.30
3.80
100
125
150
175
200
225
250
275
300
325
350
375
400
425
450
475
4.60
5.50
6.40
7.90
8.40
9.70
10.90
12.40
13.80
15.10
17.00
18.40
20.20
21.30
23.30
6
VI EXPLODED VIEW & PARTS LIST
ORDERING PARTS
Parts may be ordered by part number by calling 1-800-KEATING or your local service company. You may also order
™
Refer to the Keating Top-Side Cooker Limited Warranty for complete service and ordering information.
The model/serial plate for each cooking head is located on the the control panel assembly. The serial and model
numbers are necessary when ordering.
WARNING AND OPERATING PLATES
All warning and operating plates on the Keating Top-Side Cooker should be in place at all times. If plates are
damaged or lost, replace them immediately.
™
™
MANUAL LIFT TOP-SIDE COOKER
Figure 6-1
To control box
7
™
TOP-SIDE COOKING HEAD – MANUAL & AUTO-LIFT
Figure 6-1
PART
ITEM
DESCRIPTION
QTY.
NUMBER
1
2
THERMOSTAT TEMPERATURE PROBE KIT
COOKING HEAD (COMPLETE)
1
1
1
1
1
1
2
1
016671
1-800-KEATING
015164
---
028181
015164
017316
1-800-KEATING
012118
012119
---
3
STOP CLEVIS PIN, S/S
4
SWIVEL BRACKET WIRE SLEEVE (INCL. IN ITEM 5)
SWIVEL BRACKET
5
6
SWIVEL BRACKET SUPPORT CLEVIS PIN, S/S
COOKING SHEET MOUNTING CLIP
COVER (FOR TSC WITH MICRO LEVELER)
COOKING SHEET (SINGLE SHEET)
COOKING SHEET (PACKAGE OF 12)
7
9
10
®
11
12
MIRACLEAN COOKING FACE PLATE
1
1
1
1
1
1
2
1
4
1
1
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
6
1
1
2
2
1
1
2
2
2
4
4
1
HEATING ELEMENT 4KW, 220V (NOT SHOWN)
INSULATION BOARD (NOT SHOWN)
HIGH LIMIT PROBE
056510
016503
015173
014247
028622
028486
028487
028501
---
028488
030241
028461
---
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
HIGH LIMIT PROBE MOUNTING PLATE
KNOB
COLLAR
WORM GEAR
1
1
/
4-20X /4" ALLEN SET SCREW
HOUSING COVER
WORM GEAR WHEEL
SPUR GEAR
SHAFT
REAR COVER
FRONT HOUSING
REAR HOUSING
FRONT PLUNGER
---
---
028521
028522
028490
028500
052114
052266
052251
054444
015262
052269
052287
030269
015414
032328
052117
052286
032327
013217
052252
016383
015164
015166
014226
017046
015227
027311
REAR PLUNGER (NOT SHOWN)
TEFLON WASHER (NOT SHOWN)
FIBER WASHER (NOT SHOWN)
TOP-SIDE COOKER WELD. MANUAL
TOP-SIDE COOKER SPRING SUPPORT WELDMENT
MANUAL TOP-SIDE GAS SPRING LIFT
MANUAL TOP-SIDE COOKER GAS SPRING
5
3
SCREW /16-18 X / HEX HEAD ZINC PLATED
4
TOP-SIDE COOKER SUPPORT BRACE GAS
TOP-SIDE CONDUIT SUPPORT
1
5
NUT RIVET /4-20 X /8” 0.332 BODY
1
7
1
WASHER /
4
ID X /
SCREW /4-20 X /
8
0D X /
16
THK NICKLE
1
3
4
SERRATED FLANGE LOCK
TOP-SIDE COOKER LIFT ARM ROD
U BOLT WITH MOUNTING PLATE
3
SCREW 10-24 X /
8
SERRATED FLANGE LOCK
WASHER 0.190 ID X 0.5630 D X 0.047 THK NICKLE
MANUAL TOP-SIDE COOKER GAS SPRING ROD
1
NUT /4-20 HEX NICKLE PLATED
3
1
/
8-2 / CLEVIS PIN
2
COTTER KEYS S.S.
1
/
4-20 X 3” THREADED ROD
1
/
4” STAR WASHER
4-20 ACORN NUT
1
/
WELDMENT HANDLE GEAR GAPPING SYSTEM
8
™
AUTO-LIFT TOP-SIDE COOKER
Figure 6-2
PART
ITEM
DESCRIPTION
QTY.
NUMBER
1
2
3
4
5
6
7
8
9
TOP-SIDE COOKER WELD. AUTO NEW ARM
AUTO TOP SIDE A0-2 ACTUATOR MTG.
ACTUATOR AUTO TOPSIDE COOKER 24V
TOP-SIDE CONDUIT SUPPORT
1
1
1
1
2
1
1
2
1
052115
053991
053097
052287
052117
---
015164
015165
052591
TOP-SIDE COOKER LIFT ARM ROD
TOP-SIDE COOKER HEAD W/ CONDUIT AND CONTROL PANEL
3
1
/
8" - 2 /2" CLEVIS PIN
5
3
PIN HAIR /16" - /8" : 0.72 WIRE
TOP-SIDE COOKER LIFT ARM ROD
9
INSTRUCTIONS FOR MICROSWITCH ADJUSTMENT
AUTO-LIFT TOP-SIDE™ ACTUATOR
Figure 6-3
1. Remove the limit switch black plastic cover on the and the stroke should stop retracting before it reaches its
actuator.
mechanical stop. This movement is controlled by the
bottom micro switch.
2. Turn on the power on unit and push the T1, T2 or T3
button on the timer. The actuator will extend the stroke and 6. If the motor fails to stop, manually depress the bottom
lower head. The motor must stop and the stroke should micro switch actuator. This will disconnect power to the
stop extending before it reaches its mechanical stop. This actuator motor. Loosen the set screw (2.5mmAllen wrench)
movement is controlled by the top micro switch.
located on the bottom cam. Rotate the bottom cam counter
clockwise until the switch is made (listen for audible click.).
3. If the motor fails to stop, manually depress the top
micro switch actuator. Disconnect power to the actuator 7. Tighten the set screw on the cam, using blue locktite.
motor. Loosen the set screw (2.5mm allen wrench) located
8. Test the Top-Side head. Verify the adjustments did not
on the top cam. Rotate the top cam clockwise, until the
change the length of the stroke, thus preventing correct
switch is made (listen for audible click).
function of the top Top-Side head. The Top-Side cooking
head must be able to reach the griddle plate. If it does not
function properly, complete steps #2 through #7.
4. Tighten the set screw on the cam, using blue locktite.
5. Turn on the power and push the T1, T2 or T3 button on
the timer until it goes to the preset time. The actuator will 9. Reinstall the switch cover.
retract the stroke and raise the head. The motor must stop
10
™
TOP-SIDE COOKER CONTROL PANEL
Figure 6-4
PART
ITEM
DESCRIPTION
QTY.
NUMBER
1
THERMOSTAT
THERMOSTAT REPLACEMENT KIT
HI-LIMIT CONTROL
HI-LIMIT MOUNTING BRACKET
CONTACTOR, 50A, 3 POLE
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
056840
057138
010311
016654
011184
016689
016672
016615
016673
002565
018480
028510
034431
031584
031586
2
3
4
5
ROCKER SWITCH, LIGHTED, ON/OFF
INSTRUCTION PLATE ON/OFF SWITCH PLATE
INDICATING LIGHT, ELEMENT ON, RED
INSTRUCTION PLATE ELEMENT ON LIGHT PLATE
TERMINAL BLOCK
6
7
8
9
10
11
12
13
14
CORD, WITHOUT PLUG, 12/3 SJO
1
GROUND LUG /
4"
CONDUIT 65" COMPLETE WITH WIRES
1
CONNECTOR /2" LIQUID TIGHT 45°
1
CONNECTOR /2" LIQUID TIGHT STRAIGHT
Top View with Cover Removed
Front View
11
VII WIRING DIAGRAM
™
TOP-SIDE COOKER MANUAL LIFT WIRING DIAGRAM
Figure 6-5
LIGHTED ROCKER
LIGHTED ROCKER
ON/OFF SWITCH
GREEN LIGHT
ON TOP
ON/OFF SWITCH
GREEN LIGHT
ON BOTTOM
OR
NOTE: ANGLED TERMINALS OF SWITCH ARE ALWAYS
TOWARD CONTROL PANEL BOTTOM.
12
™
TOP-SIDE COOKER AUTO-LIFT WIRING DIAGRAM
Figure 6-6
13
SERVICE INFORMATION
If you have a service related question call 1-800-KEATING.
Please state the nature of the call; it will ensure speaking with the appropriate person.
Have your serial and model number available when ordering parts.
KEATING OF CHICAGO, INC.
8901 W. 50th Street, McCook, Illinois 60525-6001
Phone: (708) 246-3000 FAX: (708) 246-3100
Toll Free 1-800-KEATING (In U.S. and Canada)
*As continuous product improvement occurs, specifications may be changed without notice.
KEATING LIMITED WARRANTY CARD
PLEASE COMPLETE AND MAIL AT ONCE–WARRANTY IS NOT IN EFFECT UNTIL CARD IS RETURNED
COMPANY: __________________________________________________________________________________________________________________
ADDRESS: __________________________________________________________________________________________________________________
CITY: ______________________________________________________________________________ STATE: ________________ ZIP: ____________
DEALER: ____________________________________________________________________________________________________________________
DATE OF PURCHASE: ________________________________________________________________ INVOICE NUMBER: ____________________
SERIAL NUMBER: ________________________________________
REMARKS: ______________________________________________
q FRYER
q FILTER SYSTEM q GRIDDLE
q HOT PLATE q PASTA PLUS
q TOP-SIDE COOKER
I HAVE READ THE INSTALLATION AND OPERATION INSTRUCTIONS.
SIGNED: ____________________________________________________________________________________ DATE:__________________________
®
“Serving Those Who Serve The Very Best”
15
|