Intel ARRANDALE IB957 User Manual

IB957  
®
TM  
Intel Arrandale /PCH  
5.25” Motherboard  
USER’S MANUAL  
Version 1.0  
Table of Contents  
IB957 User’s Manual  
iii  
IMPORTANT NOTE: When the system boots without the CRT being  
connected, there will be no image on screen when you insert the  
CRT/VGA cable. To show the image on screen, the hotkey must be  
pressed (CTRL-ALT-F1).  
iv  
IB957 User’s Manual  
INTRODUCTION  
Introduction  
Product Description  
The IB957 5.25” Disk-Size SBC is a high performance Intel® Core™ i7-610E  
(2.53GHz/4MB) Processor-based IB957 5.25” Disk-Size SBC with the mobile  
Intel® QM57 Express Chipset. It is designed for a range of automation,  
industrial, and medical applications. The Intel® Core™ i7 Mobile processor has  
an optimized integrated graphics solution.  
IB957 features a low-power design that is validated with Intel® Core™ i7/i3  
Mobile processors on 32nm process. With two dual-channel DDR3  
800/1066MHz DIMM sockets that support ECC memory, the SBC can be  
populated with up to 8GB of system memory. Connectivity includes a Gigabit  
Ethernet port, up to 12 USB 2.0 ports, four SATA ports, a HDMI, LVDS,  
DisplayPort, DVI-D and VGA display connector. A Mini PCI-E (Mini Card) slot  
is available for expansion. Dimensions are 203mm x 146mm.  
IB957 FEATURES:  
y Supports Intel® i7-610E (2.53GHz/4MB cache) or i3-330E  
(2.13GHz/3MB cache)  
y Two DDR3 w/ ECC DIMM, Max. 8GB memory  
y Onboard Gigabit Ethernet  
y Integrated Graphics VGA for CRT/DVI/ HDMI/LVDS/DisplayPort  
y 4x SATA, 12x USB 2.0, 4x COM, Watchdog timer  
ƒ Digital I/O, Mini PCI-E socket (Mini Card)  
IB957 User’s Manual  
1
 
INTRODUCTION  
Checklist  
Your IB957 package should include the items listed below.  
The IB957 SBC  
This User’s Manual  
1 CD containing chipset drivers and flash memory utility  
Serial port cable (Part # PK1HK, 30cm)  
SATA cable (Part # SATA-7F, 46cm)  
2
IB957 User’s Manual  
 
INTRODUCTION  
IB957 Specifications  
Intel® Arrandale+ECC processor  
- i7-610E (2.53GHz/4M Cache/ 2 cores/4 Threads/35W)  
CPU Supported  
- i3-330E (2.13GHz/3M Cache/ 2 cores/4 Threads/35W)  
0.700V ~ 1.5V (IMVP-6.5)  
Up to 3.0GHz or above  
1066MHz FSB  
Up to 4MB shared L3 Cache  
CPU Voltage  
System Speed  
CPU FSB  
Cache  
APM1.2  
FcBGA1288  
Green /APM  
CPU Tpye  
Chipset  
Intel Ibex Peak-M (PCH) Chipset  
PCH: 25mm x 27mm, 1071-pin FCBGA  
AMI BIOS, supports ACPI function  
DDR3-800/1066 DIMM x2 (w/ECC function), Max. 8GB  
Arrandale DC mobile processor integrated graphics  
Supports CRT, DVI  
BIOS  
Memory  
VGA  
Supports HDMI, DP(DisplayPort)  
Arrandale DC mobile processor built-in,  
supports 24-bit, single or dual channel LVDS  
PCH 10/100/gigabit MAC + PHY  
LVDS LCD Panel  
LAN  
Intel 82577LM 10/100/1000  
PCH built-in USB 2.0 host controller, support 12 ports  
PCH built-in SATA controller, supports 4 ports  
PCH built-in Intel Active Management Technology VER 6.0 with HW  
KVM(MI957-i7-610E only)  
USB  
Serial ATA Ports  
IAMT6.0  
PCH built-in High Definition audio controller: ALC888 w/ 5.1 channels  
F81865F: COM1, COM2 (RS232/RS422/RS485), COM3 and COM4  
Hardware monitor (3 thermal, 4 voltage monitor inputs, 2 fan  
headers)  
Audio  
LPC I/O  
4 in & 4 out  
Digital IO  
Supports PS/2 keyboard/mouse connector  
Mini PCIE socket x1  
PS/2 connector x1 for keyboard/mouse and dual USB stack  
connector  
Keyboard/Mouse  
Expansion Slots  
Edge Connector  
Gigabit LAN RJ-45 + dual USB stack connector x1  
DP Connector x1 + dual USB stack connector x1  
HDMI connector x1  
DVI-D and DB15 (VGA) stack connector x1  
Quad USB stack connector x1  
RCA Jack 3x1 for Audio (Front-Out, Line-In, Mic)  
10-pin headerx1 for Digital I/O; 10-pin header x2 for COM1,COM2  
20-pin header x1 for COM3, COM4  
Onboard Header/  
Connector  
26-pin header x1 for Printer  
10-pin header x 2 for USB 9,10,11,12  
DF13 connector x2 for LVDS;  
10-pin header x1 for audio Line-Out & Mic  
4-pin header x1 for CD in, SPDIF-out connector x1  
SATA connector x4 for SATA ports  
Yes (256 segments, 0, 1, 2…255 sec/min)  
+5V, +3.3V, +12V, -12V, 5VSB  
Modem Wakeup, LAN Wakeup  
Watchdog Timer  
System Voltage  
Others  
203mm x 146mm (5.25”)  
Board Size  
IB957 User’s Manual  
3
 
INTRODUCTION  
[
Board Dimensions  
4
IB957 User’s Manual  
 
INTRODUCTION  
IB957 User’s Manual  
5
INSTALLATIONS  
Installations  
This section provides information on how to use the jumpers and  
connectors on the IB957 in order to set up a workable system. The topics  
covered are:  
6
IB957 User’s Manual  
 
INSTALLATIONS  
Installing the Memory  
The IB957 board supports two DDR3 memory socket for a maximum  
total memory of 8GB in DDR3 w/ECC DIMM memory type.  
Installing and Removing Memory Modules  
To install the DDR3 modules, locate the memory slot on the board and  
perform the following steps:  
1. Hold the DDR3 module so that the key of the DDR3 module aligned  
with that on the memory slot.  
2. Gently push the DDR3 module in an upright position until the clips of  
the slot close to hold the DDR3 module in place when the DDR3  
module touches the bottom of the slot.  
3. To remove the DDR3 module, press the clips with both hands.  
DDR3 Module  
Lock  
Lock  
Lock  
Lock  
IB957 User’s Manual  
7
 
INSTALLATIONS  
Setting the Jumpers  
Jumpers are used on IB957 to select various settings and features  
according to your needs and applications. Contact your supplier if you  
have doubts about the best configuration for your needs. The following  
lists the connectors on IB957 and their respective functions.  
IMPORTANT NOTE: When the system boots without the CRT being  
connected, there will be no image on screen when you insert the  
CRT/VGA cable. To show the image on screen, the hotkey must be  
pressed.  
8
IB957 User’s Manual  
 
INSTALLATIONS  
JP2: LCD Panel Power Selection  
JP2  
LCD Panel Power  
3.3V  
5V  
JP3, JP4, JP5: RS232/422/485 (COM2) Selection  
COM1 is fixed for RS-232 use only.  
COM2 is selectable for RS232, RS-422 and RS-485.  
The following table describes the jumper settings for COM2 selection.  
COM2  
Function  
RS-232  
RS-422  
RS-485  
JP3:  
1-2  
JP3:  
3-4  
JP3:  
5-6  
Jumper  
Setting  
JP4:  
JP4:  
JP4:  
(pin closed) 3-5 & 4-6  
1-3 & 2-4  
1-3 & 2-4  
JP5:  
JP5:  
JP5:  
3-5 & 4-6  
1-3 & 2-4  
1-3 & 2-4  
10  
IB957 User’s Manual  
 
INSTALLATIONS  
COM2 is jumper selectable for RS-232, RS-422 and RS-485.  
Pin #  
Signal Name  
RS-232  
DCD  
RX  
R2-422  
TX-  
TX+  
RS-485  
1
2
3
DATA-  
DATA+  
NC  
TX  
RX+  
4
5
6
7
8
9
10  
DTR  
Ground  
DSR  
RTS  
CTS  
RI  
RX-  
NC  
Ground  
NC  
NC  
NC  
Ground  
RTS-  
RTS+  
CTS+  
CTS-  
NC  
NC  
NC  
NC  
JBAT1: Clear CMOS Setting  
JBAT1  
Setting  
Normal  
Clear CMOS  
IB957 User’s Manual  
11  
 
INSTALLATIONS  
Connectors on IB957  
12  
IB957 User’s Manual  
 
INSTALLATIONS  
Connector Locations on IB957  
IB957 User’s Manual  
13  
 
INSTALLATIONS  
CN1: DC Adapter Connector  
CN1 provides DC12V that provide system power +5,+3.3,+12V,5VSB  
CN2: DVI-D and VGA Connector  
[
Signal Name  
Pin # Pin # Signal Name  
DATA 2-  
DATA 2+  
Shield 2/4  
DATA 4-  
DATA 4+  
DDC CLOCK  
DDC DATA  
N.C  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
C1  
C2  
C3  
C4  
C5  
C6  
HOT PLUG  
DATA 0-  
DATA 0+  
SHIELD 0/5  
DATA 5-  
DATA 5+  
SHIELD CLK  
CLOCK -  
CLOCK +  
N.C.  
DATA 1-  
DATA 1+  
SHIELD 1/3  
DATA 3-  
DATA 3+  
DDC POWER  
A GROUND 1  
N.C.  
N.C.  
N.C.  
N.C.  
N.C.  
Signal Name Pin # Pin # Signal Name  
Red  
Blue  
1
3
2
4
Green  
N.C.  
GND  
5
6
GND  
GND  
7
8
GND  
N.C.  
N.C.  
HSYNC  
DDC_CLK  
9
10  
12  
14  
GND  
DDC_DATA  
VSYNC  
11  
13  
15  
14  
IB957 User’s Manual  
 
INSTALLATIONS  
HDMI1: HDMI Connector  
Signal Name  
Pin # Pin # Signal Name  
DATA 2-  
DATA 2+  
Shield 2/4  
DATA 4-  
DATA 4+  
DDC CLOCK  
DDC DATA  
N.C  
DATA 1-  
DATA 1+  
SHIELD 1/3  
DATA 3-  
1
2
3
4
5
6
7
8
9
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
DATA 3+  
+5V Power  
GROUND  
HOT PLUG  
DATA 0-  
DATA 0+  
SHIELD 0/5  
DATA 5-  
DATA 5+  
SHIELD CLK  
CLOCK +  
10  
11  
12  
CLOCK -  
CN3: USB11/12 Ports  
J2: DisplayPort Connector  
CN4: USB6/7/8/10 Ports  
USB_LAN1: 10/100/1000 RJ-45 and USB9/13 Ports  
CN5: Audio Connector  
The audio connector, from top to bottom, is composed of Line in, Line  
out and Microphone jacks.  
IB957 User’s Manual  
15  
 
INSTALLATIONS  
COM3_COM4: COM3, COM4 Serial Port  
Signal Name Pin # Pin # Signal Name  
DSR  
RTS  
CTS  
RI  
2
4
6
1
3
5
DCD  
RXD  
TXD  
8
7
DTR  
NA  
10  
12  
14  
16  
18  
20  
9
Ground  
DCD  
RXD  
TXD  
DTR  
Ground  
DSR  
RTS  
CTS  
RI  
11  
13  
15  
17  
19  
NA  
SYS_FAN1: System Fan Power Connector  
This is a 3-pin header for system fans. The fan must be a 12V (500mA).  
Pin #  
Signal Name  
Ground  
+12V  
Rotation detection  
1
2
3
CPU_FAN1: CPU Fan Power Connector  
This is a 3-pin header for the CPU fan. The fan must be a 12V fan.  
Pin #  
Signal Name  
Ground  
+12V  
Rotation detection  
1
2
3
16  
IB957 User’s Manual  
 
INSTALLATIONS  
J1 (F_PANEL): System Function Connector  
J1 provides connectors for system indicators that provide light indication  
of the computer activities and switches to change the computer status. J2  
is a 20-pin header that provides interfaces for the following functions.  
Hard Disk Drive LED  
Reset Switch  
Not Defined  
ATX Power On Switch  
Not Defined  
Power LED  
Speaker  
Speaker: Pins 1 - 4  
This connector provides an interface to a speaker for audio  
tone generation. An 8-ohm speaker is recommended.  
Pin #  
Signal Name  
Speaker out  
No connect  
Ground  
1
2
3
4
+5V  
Power LED: Pins 11 - 15  
Pin #  
11  
12  
Signal Name  
Power LED  
No connect  
Ground  
13  
14  
15  
No connect  
Ground  
IB957 User’s Manual  
17  
 
INSTALLATIONS  
ATX Power ON Switch: Pins 7 and 17  
This 2-pin connector is an “ATX Power Supply On/Off  
Switch” on the system that connects to the power switch on  
the case. When pressed, the power switch will force the  
system to power on. When pressed again, it will force the  
system to power off.  
Reset Switch: Pins 9 and 19  
The reset switch allows the user to reset the system without  
turning the main power switch off and then on again.  
Orientation is not required when making a connection to  
this header.  
Hard Disk Drive LED Connector: Pins 10 and 20  
This connector connects to the hard drive activity LED on  
control panel. This LED will flash when the HDD is being  
accessed.  
Pin #  
10  
20  
Signal Name  
HDD Active  
5V  
18  
IB957 User’s Manual  
INSTALLATIONS  
J3: LCD Backlight Connector  
Pin #  
Signal Name  
1
2
3
4
+12V  
Backlight Enable  
Brightness Control  
Ground  
J4, J5: +12V and +5V Output Power Connectors  
J6: Printer Port Connectors  
J7: SPI Flash Connector (factory use only)  
J8: CD-In Pin Header  
Pin # Signal Name  
1
2
3
4
CD Audio R  
Ground  
Ground  
CD Audio L  
J9: PS/2 Keyboard/Mouse Connector  
Signal Name Pin Pin Signal Name  
Ground  
Vcc  
MSDATA  
MSCLK  
1
3
5
7
2
4
6
8
Ground  
Vcc  
KBDATA  
KBCLK  
NC  
9
10  
NC  
IB957 User’s Manual  
19  
 
INSTALLATIONS  
J10: Digital I/O  
Signal Name Pin Pin Signal Name  
GND  
1
3
5
7
9
2
4
6
8
10  
VCC  
OUT1  
OUT0  
IN1  
OUT3  
OUT2  
IN3  
IN2  
IN0  
J11: Front Audio Connector  
Signal Name Pin # Pin # Signal Name  
MIC2_L  
MIC2_R  
Line2_L  
Sense  
1
3
5
7
9
2
4
6
8
10  
Ground  
Presence#  
MIC2_ID  
NC  
Line2_R  
Line2_ID  
J12: PCI-E(x1) Slot  
J13: SPDIF Out Connector  
JMINI: Mini PCIE Connector  
SATA1, SATA2, SATA3, SATA4: SATA Connectors  
20  
IB957 User’s Manual  
 
INSTALLATIONS  
F_USB1: USB1/USB5 Connector  
Signal Name Pin Pin Signal Name  
Vcc  
D0-  
D0+  
1
3
5
7
2
4
6
8
Vcc  
D1-  
D1+  
Ground  
Ground  
NC  
9
10  
Ground  
F_USB2: USB0/USB3 Connector  
Signal Name Pin Pin Signal Name  
Vcc  
D0-  
D0+  
1
3
5
7
2
4
6
8
Vcc  
D1-  
D1+  
Ground  
Ground  
NC  
9
10  
Ground  
COM1,COM2: COM1,COM2 Serial Port  
COM2  
Signal Name  
DCD, Data carrier detect  
RXD, Receive data  
TXD, Transmit data  
DTR, Data terminal ready  
GND, ground  
Pin # Pin #  
Signal Name  
1
2
3
4
5
6
7
8
9
10  
DSR, Data set ready  
RTS, Request to send  
CTS, Clear to send  
RI, Ring indicator  
Not Used  
IB957 User’s Manual  
21  
 
INSTALLATIONS  
LVDS1, LVDS2: LVDS Connectors (1st channel, 2nd channel)  
The LVDS connectors on board consist of the first channel (LVDS1)  
and second channel (LVDS2).  
Signal Name Pin # Pin # Signal Name  
TX0-  
Ground  
TX1-  
2
4
6
1
3
5
TX0+  
Ground  
TX1+  
5V/3.3V  
TX3-  
TX2-  
Ground  
TXC-  
5V/3.3V  
+12V  
8
7
9
Ground  
TX3+  
TX2+  
Ground  
TXC+  
ENABKL  
+12V  
10  
12  
14  
16  
18  
20  
11  
13  
15  
17  
19  
22  
IB957 User’s Manual  
 
BIOS SETUP  
BIOS Introduction  
The BIOS (Basic Input/Output System) installed in your computer  
system’s ROM supports Intel processors. The BIOS provides critical  
low-level support for a standard device such as disk drives, serial ports  
and parallel ports. It also password protection as well as special support  
for detailed fine-tuning of the chipset controlling the entire system.  
BIOS Setup  
The BIOS provides a Setup utility program for specifying the system  
configurations and settings. The BIOS ROM of the system stores the  
Setup utility. When you turn on the computer, the BIOS is immediately  
activated. Pressing the <Del> key immediately allows you to enter the  
Setup utility. If you are a little bit late pressing the <Del> key, POST  
(Power On Self Test) will continue with its test routines, thus preventing  
you from invoking the Setup. If you still wish to enter Setup, restart the  
system by pressing the ”Reset” button or simultaneously pressing the  
<Ctrl>, <Alt> and <Delete> keys. You can also restart by turning the  
system Off and back On again. The following message will appear on  
the screen:  
Press <DEL> to Enter Setup  
In general, you press the arrow keys to highlight items, <Enter> to  
select, the <PgUp> and <PgDn> keys to change entries, <F1> for help  
and <Esc> to quit.  
When you enter the Setup utility, the Main Menu screen will appear on  
the screen. The Main Menu allows you to select from various setup  
functions and exit choices.  
24  
IB957 User’s Manual  
 
BIOS SETUP  
Main BIOS Setup  
This setup allows you to record some basic hardware configurations in  
your computer system and set the system clock.  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
BIOS INFORMATION  
BIOS Vendor  
American Megatrends  
Select Screen  
↑↓ Select Item  
Enter: Select  
Memory Information  
Total Memory  
4096 MB (DDR3 1066)  
+- Change Field  
F1: General Help  
F2: Previous Values  
F3: Optimized Default  
System Date  
System Time  
[Tue 01/06/2009  
[00:08:21]  
F4: Save ESC: Exit  
Access Level  
Administrator  
Note:  
If the system cannot boot after making and saving system  
changes with Setup, the AMI BIOS supports an override to  
the CMOS settings that resets your system to its default.  
Warning: It is strongly recommended that you avoid making any  
changes to the chipset defaults. These defaults have been  
carefully chosen by both AMI and your system manufacturer  
to provide the absolute maximum performance and  
reliability. Changing the defaults could cause the system to  
become unstable and crash in some cases.  
System Language  
Choose the system default language.  
System Date  
Set the Date. Use Tab to switch between Data elements.  
System Time  
Set the Time. Use Tab to switch between Data elements.  
IB957 User’s Manual  
25  
 
BIOS SETUP  
Advanced Settings  
This section allows you to configure and improve your system and  
allows you to set up some system features according to your preference.  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
Legacy OpROM Support  
Launch PXE OpROM  
Launch Storage OpROM  
PCI Subsystem Settings  
ACPI Settings  
Wake up event setting  
CPU Configuration  
SATA Configuration  
Thermal Configuration  
Intel IGD SWSCI OpRegion  
Select Screen  
Intel TDT(AT-p) Configurations  
USB Configuration  
↑↓ Select Item  
Enter: Select  
Super IO Configuration  
H/W Monitor  
+- Change Field  
F1: General Help  
Intelligent Power Sharing  
AMT Configuration  
F2: Previous Values  
F3: Optimized Default  
F4: Save ESC: Exit  
Serial Port Console Redirection  
Launch PXE OpROM  
Enable or Disable Boot Option for Legacy Network Devices.  
Launch Storage OpROM  
Enable or Disable Boot Option for Legacy Mass Storage Devices with Option  
ROM.  
Wake up event setting  
Enable/Disable Wake up event.  
Intel TDT(AT-p) Configurations  
Disabling TDT Allow user to login to platform. This is strictly for testing only.  
This does not disable TDT Services in ME.  
26  
IB957 User’s Manual  
 
BIOS SETUP  
PCI Subsystem Settings  
This section allows you to configure the PCI, PCI-X and PCI Express  
settings.  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
PCI Bus Driver Version  
PCI ROM Priority  
V 2.02.01  
EFI Compatible ROM  
PCI Common Settings  
PCI Latency Timer  
32 PCI Bus Clocks  
PCI Express Device Settings  
Extended Tag  
Disabled  
Enabled  
Auto  
No Snoop  
Maximum Payload  
Maximum Read Request  
Select Screen  
Auto  
↑↓ Select Item  
Enter: Select  
+- Change Field  
F1: General Help  
PCI Express Link Settings  
ASPM Support  
Disabled  
WARNING: Enabling ASPM may cause  
F2: Previous Values  
F3: Optimized Default  
F4: Save ESC: Exit  
Some PCI-E devices to fail  
PCI ROM Priority  
In case of multiple Option ROMs (Legacy and EFI Compatible), specifies what  
PCI Option ROM to launch.  
PCI Latency Timer  
Value to be programmed into PCI Latency Timer Register.  
Extended Tag  
If ENABLED allows Device to use 8-bit Tag field as a requester.  
No Snoop  
Enables or Disables PCI Express Device No Snoop option.  
Maximum Payload  
Set Maximum Payload of PCI Express Device or allow System BIOS to select  
the value.  
Maximum Read Request  
Launches (Enabled/Disabled) the boot option for legacy network devices.  
IB957 User’s Manual  
27  
BIOS SETUP  
PCI Express Link Settings  
Set Maximum Read Request Size of PCI Express Device or allow System BIOS  
to select the value.  
ASPM Support  
Set the ASPM Level:  
Force L0 Force all links to L0 State  
AUTO BIOS auto configure  
DISABLE Disables ASPM  
28  
IB957 User’s Manual  
BIOS SETUP  
ACPI Settings  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
Enable ACPI Auto Configuration  
Disabled  
Select Screen  
↑↓ Select Item  
Enter: Select  
ACPI Sleep State  
S3 (Suspend to R…)  
+- Change Field  
F1: General Help  
F2: Previous Values  
F3: Optimized Default  
F4: Save ESC: Exit  
Enabled ACPI Auto Configuration  
Enables or Disables BIOS ACPI Auto Configuration.  
ACPI Sleep State  
Select the highest ACPI sleep state the system will enter, when the SUSPEND  
button is pressed.  
IB957 User’s Manual  
29  
BIOS SETUP  
Wake up event settings  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
Wake system with Fixed Time  
Wake up hour  
Disabled  
0
0
0
Select Screen  
↑↓ Select Item  
Enter: Select  
Wake up minute  
Wake up second  
+- Change Field  
F1: General Help  
Wake on Ring  
Disabled  
Disabled  
Disabled  
Wake on PCI PME  
Wake on PCIE Wake Event  
F2: Previous Values  
F3: Optimized Default  
F4: Save ESC: Exit  
Wake system with Fixed Time  
Enables or Disables System wake on alarm event. When enabled, System will  
wake on the hr::min:: sec specified.  
Wake on Ring  
The options are Disabled and Enabled.  
Wake on PCI PME  
The options are Disabled and Enabled.  
30  
IB957 User’s Manual  
BIOS SETUP  
CPU Configuration  
This section shows the CPU configuration parameters.  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
CPU Configuration  
Processor Type  
EMT64  
Intel(R) Core(TM) i5 CPU  
Supported  
2394 MHz  
20652  
9
Processor Speed  
Processor Stepping  
Microcode Revision  
Processor Cores  
Intel HT Technology  
2
Supported  
Hyper-threading  
Enabled  
All  
Active Processor Cores  
Limit CPUID Maximum  
Execute Disable Bit  
Select Screen  
↑↓ Select Item  
Enter: Select  
+- Change Field  
F1: General Help  
Disabled  
Enabled  
Enabled  
Enabled  
Disabled  
Hardware Prefetcher  
Adjacent Cache Line Prefetch  
Intel Virtualization Technology  
F2: Previous Values  
F3: Optimized Default  
F4: Save ESC: Exit  
Hyper-threading  
Enabled for Windows XP and Linux (OS optimized for Hyper-Threading  
Technology) and Disabled for other OS (OS not optimized for Hyper-Threading  
Technology). When Disabled, only one thread per enabled core is enabled.  
Active Processor Cores  
Number of cores to enable in each processor package.  
Limit CPUID Maximum  
Disabled for Windows XP.  
Execute Disable Bit  
XD can prevent certain classes of malicious buffer overflow attacks when  
combined with a supporting OS (Windows Server 2003 SP1, Windows XP SP2,  
SuSE Linux 9.2, Re33dHat Enterprise 3 Update 3.)  
Hardware Prefetcher  
To turn on/off the MLC streamer prefetcher.  
IB957 User’s Manual  
31  
BIOS SETUP  
Adjacent Cache Line Prefetch  
To turn on/off prefetching of adjacent cache lines.  
Intel Virtualization Technology  
When enabled, a VMM can utilize the additional hardware capabilities provided  
by Vanderpool Technology.  
Power Technology  
Enable the power management features.  
SATA Configuration  
SATA Devices Configuration.  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
SATA Configuration  
Select Screen  
↑↓ Select Item  
Enter: Select  
+- Change Field  
F1: General Help  
SATA Port0  
SATA Port1  
SATA Port2  
SATA Port3  
SATA Port4  
SATA Port5  
Hitachi HDS721 (160.0GB)  
Not Present  
Not Present  
Not Present  
Not Present  
F2: Previous Values  
F3: Optimized Default  
ATAPI iHDS11 ATAPI  
F4: Save ESC: Exit  
SATA Mode  
IDE Mode  
Compatibled  
Enhanced  
Serial-ATA Controller 0  
Serial-ATA Controller 1  
SATA Mode  
Options are:  
(1) IDE Mode  
(2) AHCI Mode  
(3) RAID Mode  
Serial-ATA Controller  
Options are:  
Disable  
(1) Enhanced  
(2) Compatible  
32  
IB957 User’s Manual  
BIOS SETUP  
Intel IGD SWSCI OpRegion  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
Intel IGD SWSCI OpRegion Configuration  
DVMT/FIXED Memory  
IGD – Boot Type  
256MB  
VBIOS Default  
No LVDS  
Auto  
Active LVDS  
Select Screen  
↑↓ Select Item  
Enter: Select  
+- Change Field  
F1: General Help  
LVDS Channel Type  
LVDS Panel Color Depth  
LVDS LCD Panel Type  
18bit  
1024x768 LVDS  
F2: Previous Values  
F3: Optimized Default  
F4: Save ESC: Exit  
DVMT/FIXED Memory  
Select DVMT/FIXED Mode Memory size used by Internal Graphics Device.  
Options are 128MB, 256MB and Maximum.  
IGD – Boot Type  
Select the Video Device which will be activated during POST. This has no effect  
if external graphics present. Options are VBIOS Default, CRT, LVDS,  
DisplayPort, HDMI, DVI, CRT+LVDS, CRT+HDMI and CRT+DVI.  
Active LVDS  
Select the Active LVDS Configuration.  
No LVDS: VBIOS does not enable LVDS.  
Int-LVDS: VBIOS enables LVDS driver by Integrated encoder.  
SDVO LVDS : VBIOS enables LVDS driver by SDVO encoder.  
eDP: LVDS Driven by Int-DisplayPort encoder.  
LVDS Channel Type  
The default setting is Auto. Other settings are Single and Double.  
LVDS Panel Color Depth  
The default setting is 18bit. The other optoin is 24bit.  
LVDS LCD Panel Type  
The default setting is 1024x768 LVDS.  
IB957 User’s Manual  
33  
BIOS SETUP  
Intel TDT(AT-p) Configurations  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
Intel Theft Deterrence Technology Configuration  
TDT  
Disabled  
Select Screen  
↑↓ Select Item  
Enter: Select  
TDT Recovery  
3
+- Change Field  
F1: General Help  
F2: Previous Values  
F3: Optimized Default  
F4: Save ESC: Exit  
TDT  
Enable/Disable TDT in BIOS for testing only.  
TDT Recovery  
Set the number of times Recovery attempted will be allowed.  
34  
IB957 User’s Manual  
BIOS SETUP  
USB Configuration  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
USB Configuration  
Select Screen  
↑↓ Select Item  
Enter: Select  
USB Devices:  
2 Hubs  
+- Change Field  
F1: General Help  
Legacy USB Support  
EHCI Hand-off  
Enabled  
Enabled  
20 sec  
F2: Previous Values  
F3: Optimized Default  
Device Reset Timeout  
F4: Save ESC: Exit  
Legacy USB Support  
Enables Legacy USB support.  
AUTO option disables legacy support if no USB devices are connected.  
DISABLE option will keep USB devices available only for EFI applications.  
EHCI Hand-off  
Enabled/Disabled. This is a workaround for Oses without EHCI hand-off  
support. The EHCI ownership change should be claimed by EHCI driver.  
Device Reset Timeout  
USB mass storage device Start Unit command timeout.  
Options are: 10 sec / 20 sec / 30 sec / 40 sec.  
IB957 User’s Manual  
35  
BIOS SETUP  
Super IO Configuration  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
Super IO Configuration  
Select Screen  
↑↓ Select Item  
Enter: Select  
+- Change Field  
F1: General Help  
Super IO Chip  
Fintek F81865  
-> Serial Port 0 Configuration  
-> Serial Port 1 Configuration  
-> Serial Port 2 Configuration  
-> Serial Port 3 Configuration  
Parallel Port Configuration  
Power Failure  
F2: Previous Values  
F3: Optimized Default  
Always off  
Disable  
F4: Save ESC: Exit  
ACPI Shutdown Temperature  
Serial Port Configuration  
Set Parameters of Serial Ports. User can Enable/Disable the serial port and  
Select an optimal settings for the Super IO Device.  
Power Failure  
Options are:  
Keep last state  
Bypass mode  
Always on  
Always off (default)  
Parallel Port Configuration  
Set Parameters of the parallel port. The default setting is 378F/IRQ7.  
ACPI Shutdown Temperature  
The system will shut down automatically under OS with ACPI mode, when the  
CPU temperature reaches the configured temperature.  
36  
IB957 User’s Manual  
BIOS SETUP  
H/W Monitor  
Aptio Setup Utility  
Boot Security  
Main  
Advanced  
Chipset  
Save & Exit  
Event Logs  
PC Health Status  
CPU Temperature  
+51 C  
System Temperature  
+35 C  
CPU FAN Speed  
7109 RPM  
+3.408 V  
+0.928 V  
+5.087 V  
+11.880V  
+1.552 V  
+3.392  
VCC3V  
Select Screen  
↑↓ Select Item  
Enter: Select  
+- Change Field  
F1: General Help  
Vcore  
5V  
12V  
1.5V  
VSB3V  
F2: Previous Values  
F3: Optimized Default  
VBAT  
+3.184 V  
Disabled  
CPU Fan Smart Fan Control  
F4: Save ESC: Exit  
Temperatures/Voltages  
These fields are the parameters of the hardware monitoring function  
feature of the motherboard. The values are read-only values as  
monitored by the system and show the PC health status.  
CPU Fan Smart Fan Control  
This field enables or disables the smart fan feature. At a certain  
temperature, the fan starts turning. Once the temperature drops to a  
certain level, it stops turning again.  
IB957 User’s Manual  
37  
BIOS SETUP  
Thermal Configuration  
Aptio Setup Utility  
Boot Security  
Main  
Advanced  
Chipset  
Save & Exit  
Event Logs  
Thermal Configuration  
Intelligent Power Sharing  
Select Screen  
↑↓ Select Item  
Enter: Select  
+- Change Field  
F1: General Help  
F2: Previous Values  
F3: Optimized Default  
F4: Save ESC: Exit  
Intelligent Power Sharing  
Intelligent power sharing – The default setting is Enabled.  
Mch Turbo – The default setting is Enabled.  
IPS Policy – The default setting is Driver.  
Core Temp Limit – The default setting is Disabled.  
Mch Power Limit – The default setting is Disabled.  
Processor Power Limit - The default setting is Disabled.  
Core Power Limit – The default setting is Disabled.  
38  
IB957 User’s Manual  
BIOS SETUP  
AMT Configuration  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
AMT  
Enabled  
Disabled  
Unconfigure AMT/ME  
Select Screen  
↑↓ Select Item  
Enter: Select  
+- Change Field  
F1: General Help  
F2: Previous Values  
F3: Optimized Default  
F4: Save ESC: Exit  
AMT  
Options are Enabled and Disabled.  
Unconfigure AMT/ME  
Perform AMT/ME unconfigure without password operation.  
Serial Port Console Redirection  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
COM0 (Disabled)  
Console Redirection  
Port is Disabled  
Select Screen  
↑↓ Select Item  
Enter: Select  
+- Change Field  
F1: General Help  
Serial Port for Out-of-Band Management/  
Windows Emergency Management Services (EMS)  
Console Redirection  
Out-of-Band Mgmt Port  
Data Bits  
Enabled  
COM0 (Disabled)  
F2: Previous Values  
F3: Optimized Default  
8
Parity  
None  
1
F4: Save ESC: Exit  
Stop Bits  
Terminal Type  
VT-UTF8  
Console Redirection  
Console Redirection Enable/Disable.  
Terminal Type  
VT-UTF8 is the preferred terminal type for out-of-band management. The next  
best choice is VT100+ and then VT100.  
IB957 User’s Manual  
39  
BIOS SETUP  
Chipset Settings  
This section allows you to configure and improve your system and  
allows you to set up some system features according to your preference.  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
Enable CSID  
Disabled  
North Bridge  
South Bridge  
ME Subsystem  
Select Screen  
↑↓ Select Item  
Enter: Select  
+- Change Field  
F1: General Help  
F2: Previous Values  
F3: Optimized Default  
F4: Save ESC: Exit  
Enable CSID  
By default, this item is disabled. Enable Compatible Revision ID.  
North Bridge  
This item shows the North Bridge Parameters.  
South Bridge  
This item shows the South Bridge Parameters.  
ME Subsystem  
This item shows the ME Subsystem Parameters.  
40  
IB957 User’s Manual  
 
BIOS SETUP  
North Bridge  
This section allows you to configure the North Bridge Chipset.  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
Memory Information  
CPU Type  
Arrandale  
Total Memory  
Memory Slot0  
Memory Slot1  
Memory Slot2  
Memory Slot3  
4096 MB (DDR3 1066)  
2048 MB (DDR3 1066)  
0
2048 MB (DDR3 1066)  
140  
CAS# Latency(tCL)  
7
Select Screen  
↑↓ Select Item  
Enter: Select  
+- Change Field  
F1: General Help  
RAS# Active Time(tRAS)  
20  
7
Row Precharge Time(tRP)  
RAS# to CAS# Delay(tRCD)  
Row Refresh Cycle Timea(tRFC)  
Write to Read Delay(tWTR)  
Active to Active Delay(tRRD)  
Read CAS# Precharge(tRTP)  
7
60  
4
4
F2: Previous Values  
F3: Optimized Default  
5
F4: Save ESC: Exit  
Low MMIO Align  
64M  
Initiate Graphic Adapter  
Graphics Turbo IMON Current  
VT-d  
PEG/IGD  
31  
Disabled  
Disabled  
Auto  
PCI Express Compliance Mode  
PCI Express Port  
IGD Memory  
32M  
Low MMIO Align  
Low MMIO resources align at 64MB/1024MB.  
Initiate Graphic Adapter  
Select which graphics controller to use as the primary boot device.  
Options are IGD, PCI/IGD, PCI/PEG, PEG/IGD, PEG/PCI and SG.  
Graphics Turbo IMON Current  
Graphics turbo IMON current values supported (14-31).  
VT-d  
VT-d Enable/Disable.  
PCI Express Compliance Mode  
PCI Express Compliance Mode Enable/Disable.  
IB957 User’s Manual  
41  
BIOS SETUP  
PCI Express Port  
Options are Disabled, Enabled and Auto.  
IGD Memory  
IGD Share Memory Size. Options are Disable, 32M, 64M and 128M.  
PAVP Mode  
Select PAVP Mode used by Internal Graphics Device. Options are Disabled and  
Enabled.  
PEG Force Gen1  
PCI Express Port Force Gen1. Options are Disabled and  
42  
IB957 User’s Manual  
BIOS SETUP  
SB Chipset Configuration  
This section allows you to configure the South Bridge Chipset.  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
SB Chipset Configuration  
SMBus Controller  
GbE Controller  
Enabled  
Enabled  
Enabled  
Wake on LAN from S5  
SLP_S4 Assertion Stretch Enable  
SLP_S4 Assertion Width  
Enabled  
1-2 Seconds  
Audio Configuration  
Azalia HD Audio  
Select Screen  
↑↓ Select Item  
Enter: Select  
Enabled  
Enabled  
Azalia Internal HDMI codec  
High Precision Event Timer Configuration  
High Precision Timer  
+- Change Field  
F1: General Help  
Enabled  
F2: Previous Values  
F3: Optimized Default  
PCI Express Ports Configuration  
USB Configuration  
F4: Save ESC: Exit  
SMBus Controller  
SMBus Controller help.  
GbE Controller  
This is constantly enabled.  
Wake on LAN from S5  
Wake on LAN from S5 help.  
SLP_S4 Assertion Stretch Enable  
Select a minimum assertion width of the SLP_S4# signal.  
Audio Configuration  
The Audio Configuration settings Enable/Disable the Azalia HD Audio and the  
Azalia internal HDMI codec.  
High Precision Event Timer Configuration  
Enable/or Disable the High Precision Event Timer.  
IB957 User’s Manual  
43  
BIOS SETUP  
PCI Express Ports Configuration  
Enable or Disable the PCI Express Ports in the Chipset.  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
PCI Express Ports Configuration  
PCI Express Port 1  
PCI Express Port 2  
PCI Express Port 3  
PCI Express Port 4  
PCI Express Port 5  
PCI Express Port 6  
PCI Express Port 7  
PCI Express Port 8  
Auto  
Auto  
Auto  
Auto  
Auto  
Auto  
Auto  
Auto  
Select Screen  
↑↓ Select Item  
Enter: Select  
+- Change Field  
F1: General Help  
F2: Previous Values  
F3: Optimized Default  
F4: Save ESC: Exit  
USB Configuration  
Enable/Disable All USB Devices, USB 2.0 (EHCI) Support and RMH  
Support. The setting of AUTO on RMH Support Enable RMH support  
on Ibex Peak B0 Stepping.  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
USB Configuration  
All USB Devices  
Enabled  
Select Screen  
↑↓ Select Item  
Enter: Select  
+- Change Field  
F1: General Help  
EHCI Controller 1  
EHCI Controller 2  
RMH Support  
Enabled  
Enabled  
Auto  
USB Port 0  
USB Port 1  
USB Port 2  
USB Port 3  
USB Port 4  
USB Port 5  
USB Port 6  
USB Port 7  
USB Port 8  
USB Port 9  
USB Port 10  
USB Port 11  
USB Port 12  
USB Port 13  
Enabled  
Enabled  
Enabled  
Enabled  
Enabled  
Enabled  
Enabled  
Enabled  
Enabled  
Enabled  
Enabled  
Enabled  
Enabled  
Enabled  
F2: Previous Values  
F3: Optimized Default  
F4: Save ESC: Exit  
44  
IB957 User’s Manual  
BIOS SETUP  
Intel ME Subsystem  
This section allows you to configure the PCI settings.  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
Intel ME Subsystem Configuration  
ME Version  
Select Screen  
↑↓ Select Item  
Enter: Select  
+- Change Field  
F1: General Help  
6.0.3.1195  
ME Subsystem  
Enabled  
Enabled  
Enabled  
End of Post Message  
Execute ME8x  
F2: Previous Values  
F3: Optimized Default  
F4: Save ESC: Exit  
ME Version  
Launches (Enabled/Disabled) the boot option for legacy network devices.  
ME Subsystem  
Launches (Enabled/Disabled) the boot option for legacy network devices.  
End of Post Message  
Launches (Enabled/Disabled) the boot option for legacy network devices.  
Execute ME8x  
Launches (Enabled/Disabled) the boot option for legacy network devices.  
IB957 User’s Manual  
45  
BIOS SETUP  
Boot Settings  
This section allows you to configure the boot settings according to your  
preference.  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
Boot Configuration  
Quiet Boot  
Disabled  
Fast Boot  
Disabled  
1
Setup Prompt Timeout  
Bootup NumLock State  
CSM16 Module Version  
GateA20 Active  
On  
07.60  
Upon Request  
Force BIOS  
Disabled  
Select Screen  
↑↓ Select Item  
Enter: Select  
+- Change Field  
F1: General Help  
Option ROM Messages  
Interrupt 19 Canture  
Boot Option Priorities  
Boot Option #1  
SATA: ATAPI iH…)  
F2: Previous Values  
F3: Optimized Default  
F4: Save ESC: Exit  
Quiet Boot  
Enables/Disables Quiet Boot option.  
Fast Boot  
Enables/Disables boot with initialization of a minimal set of devices required to  
launch active boot option. Has no effect for BBS boot options.  
Setup Prompt Timeout  
Number of seconds to wait for setup activation key.  
65535(0xFFFF) means indefinite waiting.  
Bootup NumLock State  
Select the keyboard NumLock state.  
GateA20 Active  
UPON REQUEST GA20 can be disabled using BIOS services.  
ALWAYS do not allow disabling GA20; this option is useful when any RT  
code is executed above 1MB.  
Option ROM Messages  
Set display mode for Option ROM. Options are Force BIOS and Keep Current.  
Interrupt 19 Canture  
Enable: Allows Option ROMs to trap Int 19.  
46  
IB957 User’s Manual  
 
BIOS SETUP  
Boot Option Priorities  
Sets the system boot order.  
Hard Drive BBS Priorities  
Set the order of the legacy devices in this group.  
Security Settings  
This section allows you to configure and improve your system and  
allows you to set up some system features according to your preference.  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
Password Description  
If ONLY the Administrator’s password is set, then  
this only limits accesss to Setup and is only asked  
for when entering Setup.  
Select Screen  
If ONLY the User’s password is set, then this is a  
power on password and must be entered to boot  
or enter Setup. In Setup the User will have  
Administrator rights  
↑↓ Select Item  
Enter: Select  
+- Change Field  
F1: General Help  
F2: Previous Values  
F3: Optimized Default  
Administrator Password  
User Password  
F4: Save ESC: Exit  
Administrator Password  
Set Setup Administrator Password.  
User Password  
Set User Password.  
IB957 User’s Manual  
47  
 
BIOS SETUP  
Save & Exit Settings  
Aptio Setup Utility  
Boot Security  
Main  
Advanced  
Chipset  
Save & Exit  
Event Logs  
Save Changes and Exit  
Disacard Changes and Exit  
Save Changes and Reset  
Discard Changes and Reset  
Select Screen  
↑↓ Select Item  
Enter: Select  
+- Change Field  
F1: General Help  
Save Options  
Save Changes  
Discard Changes  
F2: Previous Values  
F3: Optimized Default  
Restore Defaults  
Save as User Defaults  
Restore User Defaults  
F4: Save ESC: Exit  
Boot Override  
SATA: ATAPI iHDS116  
4
SATA: Hitachi HDS721616PLA380  
Launch EFI Shell from filesystem device  
Save Options  
Reset System with ME disable Mode  
Save Changes and Exit  
Exit system setup after saving the changes.  
Disacard Changes and Exit  
Exit system setup without saving any changes.  
Save Changes and Reset  
Reset the system after saving the changes.  
Discard Changes and Reset  
Reset system setup without saving any changes.  
Save Changes  
Save Changes done so far to any of the setup options.  
Discard Changes  
Discard Changes done so far to any of the setup options.  
Restore Defaults  
Restore/Load Defaults values for all the setup options.  
48  
IB957 User’s Manual  
 
BIOS SETUP  
Save as User Defaults  
Save the changes done so far as User Defaults.  
Restore User Defaults  
Restore the User Defaults to all the setup options.  
Boot Override  
Pressing ENTER causes the system to enter the OS.  
Launch EFI Shell from filesystem device  
Attempts to Launch EFI Shell application (Shellx64.efi) from one of the  
available filesystem devices.  
Reset System with ME disable Mode  
ME will run into the temporary disable mode.  
IB957 User’s Manual  
49  
BIOS SETUP  
Event Logs  
This section allows you to configure the Smbios Event Log. according to  
your preference.  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Save & Exit  
Event Logs  
Change Smbios Event Log Settings  
Press Enter to change Smbios  
Event Log Configuration  
View Smbios Event Log  
View System Event Log  
Select Screen  
↑↓ Select Item  
Enter: Select  
+- Change Field  
F1: General Help  
F2: Previous Values  
F3: Optimized Default  
F4: Save ESC: Exit  
Aptio Setup Utility  
Main  
Advanced  
Chipset  
Boot  
Security  
Enabled  
Save & Exit  
Event Logs  
Enabling/Disabling Options  
Change this to enable/disable all  
features of Smbios Logging during  
boot.  
Smbios Event Log  
Erasing Settings  
Erase Event Log  
When Log is Full  
Select Screen  
↑↓ Select Item  
Enter: Select  
No  
Do Nothing  
+- Change Field  
F1: General Help  
Smbios Even tLog Standard Settings  
MECI  
1
F2: Previous Values  
METW  
60  
F3: Optimized Default  
Custom Options  
F4: Save ESC: Exit  
Log OEM Codes  
Enabled  
Disabled  
Convert OEM Codes  
NOTE: All values changed here do not take effect  
until computer is restarted  
50  
IB957 User’s Manual  
 
DRIVERS INSTALLATION  
Drivers Installation  
This section describes the installation procedures for software and  
drivers under Windows operating systems. The software and drivers are  
included with the motherboard. If you find the items missing, please  
contact the vendor where you made the purchase. The contents of this  
section include the following:  
IB957 User’s Manual  
51  
 
DRIVER INSTALLATION  
Intel Chipset Software Installation Utility  
The Intel Chipset Drivers should be installed first before the software  
drivers to enable Plug & Play INF support for Intel chipset components.  
Follow the instructions below to complete the installation.  
1. Insert the CD that comes with the board. Click Intel and then Intel(R)  
QM57 Chipset Drivers.  
2. Click Intel(R) Chipset Software Installation Utility.  
3. When the Welcome screen to the Intel® Chipset Device Software  
appears, click Next to continue.  
52  
IB957 User’s Manual  
 
DRIVERS INSTALLATION  
4. Click Yes to accept the software license agreement and proceed with  
the installation process.  
5. On the Readme File Information screen, click Next to continue the  
installation.  
6. The Setup process is now complete. Click Finish to restart the  
computer and for changes to take effect.  
IB957 User’s Manual  
53  
DRIVER INSTALLATION  
VGA Drivers Installation  
NOTE: Before installing the Intel(R) QM57 Chipset Family Graphics  
Driver, the Microsoft .NET Framework 3.5 SPI should be first  
installed.  
To install the VGA drivers, follow the steps below.  
1. Insert the CD that comes with the board. Click Intel and then Intel(R)  
QM57 Chipset Drivers.  
2. Click Intel(R) QM57 Chipset Family Graphics Driver.  
3. When the Welcome screen appears, click Next to continue.  
54  
IB957 User’s Manual  
 
DRIVERS INSTALLATION  
4. Click Yes to to agree with the license agreement and continue the  
installation.  
5. On the Readme File Information screen, click Next to continue the  
installation of the Intel® Graphics Media Accelerator Driver.  
6. On Setup Progress screen, click Next to continue.  
7. Setup complete. Click Finish to restart the computer and for changes  
to take effect.  
IB957 User’s Manual  
55  
DRIVER INSTALLATION  
Realtek HD Audio Driver Installation  
Follow the steps below to install the Realtek HD Audio Drivers.  
1. Insert the CD that comes with the board. Click Intel and then Intel(R)  
QM57 Chipset Drivers.  
2. Click Realtek High Definition Audio Driver.  
3. On the Welcome to the InstallShield Wizard screen, click Next.  
3. InstallShield Wizard is complete. Click Finish to restart the computer.  
56  
IB957 User’s Manual  
 
DRIVERS INSTALLATION  
LAN Drivers Installation  
Follow the steps below to install the Intel LAN drivers.  
1. Insert the CD that comes with the board. Click Intel and then Intel(R)  
QM57 Chipset Drivers.  
2. Click Intel(R) PRO LAN Network Driver.  
3. When the Welcome screen appears, click Next. On the next screen,  
click Yes to to agree with the license agreement.  
IB957 User’s Manual  
57  
 
DRIVER INSTALLATION  
4. Click the checkbox for Drivers in the Setup Options screen to select  
it and click Next to continue.  
5. The wizard is ready to begin installation. Click Install to begin the  
installation.  
58  
IB957 User’s Manual  
DRIVERS INSTALLATION  
6. When InstallShield Wizard is complete, click Finish.  
IB957 User’s Manual  
59  
DRIVER INSTALLATION  
Intel® Management Engine Interface  
NOTE: Before installing the Intel(R) AMT 6.0 Drivers, the  
Microsoft .NET Framework 3.5 SPI should be first installed.  
Follow the steps below to install the Intel Management Engine.  
1. Insert the drivers disc that comes with the motherboard. Click Intel  
and then Intel(R) AMT 6.0 Drivers.  
60  
IB957 User’s Manual  
 
DRIVERS INSTALLATION  
2. When the Welcome screen to the InstallShield Wizard for Intel®  
Management Engine Components, click Next. On the next screen, click  
Yes to to agree with the license agreement.  
2. When the Setup Progress screen appears, click Next. Then, click  
Finish when the setup progress has been successfully installed.  
IB957 User’s Manual  
61  
DRIVER INSTALLATION  
62  
IB957 User’s Manual  
APPENDIX  
Appendix  
A. I/O Port Address Map  
Each peripheral device in the system is assigned a set of I/O port  
addresses which also becomes the identity of the device. The following  
table lists the I/O port addresses used.  
Address  
Device Description  
DMA Controller #1  
Interrupt Controller #1  
Timer  
Keyboard Controller  
Real Time Clock, NMI  
DMA Page Register  
Interrupt Controller #2  
DMA Controller #2  
Clear Math Coprocessor Busy Signal  
Reset Math Coprocessor  
IDE Interface  
Parallel Port #2(LPT2)  
Serial Port #4(COM4)  
Serial Port #2(COM2)  
Graphics adapter Controller  
Network Ports  
000h - 01Fh  
020h - 03Fh  
040h - 05Fh  
060h - 06Fh  
070h - 07Fh  
080h - 09Fh  
0A0h - 0BFh  
0C0h - 0DFh  
0F0h  
0F1h  
1F0h - 1F7h  
278h - 27Fh  
2E8h – 2EFh  
2F8h - 2FFh  
2B0h- 2DFh  
360h - 36Fh  
3B0h - 3BFh  
3C0h - 3CFh  
3D0h - 3DFh  
3E8h – 3EFh  
3F8h - 3FFh  
Monochrome & Printer adapter  
EGA adapter  
CGA adapter  
Serial Port #3(COM3)  
Serial Port #1(COM1)  
IB957 User’s Manual  
63  
 
APPENDIX  
B. Interrupt Request Lines (IRQ)  
Peripheral devices use interrupt request lines to notify CPU for the  
service required. The following table shows the IRQ used by the devices  
on board.  
Level  
IRQ0  
IRQ1  
IRQ2  
IRQ3  
IRQ4  
IRQ5  
IRQ6  
IRQ7  
IRQ8  
IRQ9  
IRQ10  
IRQ11  
IRQ12  
IRQ13  
IRQ14  
IRQ15  
Function  
System Timer Output  
Keyboard  
Interrupt Cascade  
Serial Port #2  
Serial Port #1  
Reserved  
Reserved  
Reserved  
Real Time Clock  
Reserved  
Serial Port #3  
Serial Port #4  
PS/2 Mouse  
80287  
Primary IDE  
Secondary IDE  
64  
IB957 User’s Manual  
 
APPENDIX  
C. Watchdog Timer Configuration  
The WDT is used to generate a variety of output signals after a user  
programmable count. The WDT is suitable for use in the prevention of  
system lock-up, such as when software becomes trapped in a deadlock.  
Under these sorts of circumstances, the timer will count to zero and the  
selected outputs will be driven. Under normal circumstance, the user  
will restart the WDT at regular intervals before the timer counts to zero.  
SAMPLE CODE:  
//---------------------------------------------------------------------------  
//  
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY  
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE  
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR  
// PURPOSE.  
//  
//---------------------------------------------------------------------------  
#include <dos.h>  
#include <conio.h>  
#include <stdio.h>  
#include <stdlib.h>  
#include "F81865.H"  
//---------------------------------------------------------------------------  
int main (int argc, char *argv[]);  
void EnableWDT(int);  
void DisableWDT(void);  
//---------------------------------------------------------------------------  
int main (int argc, char *argv[])  
{
unsigned char bBuf;  
unsigned char bTime;  
char **endptr;  
char SIO;  
printf("Fintek 81865 watch dog program\n");  
SIO = Init_F81865();  
if (SIO == 0)  
{
printf("Can not detect Fintek 81865, program abort.\n");  
return(1);  
}//if (SIO == 0)  
if (argc != 2)  
{
printf(" Parameter incorrect!!\n");  
return (1);  
}
bTime = strtol (argv[1], endptr, 10);  
printf("System will reset after %d seconds\n", bTime);  
if (bTime)  
{
EnableWDT(bTime); }  
else  
{
DisableWDT();  
}
IB957 User’s Manual  
65  
 
APPENDIX  
return 0;  
}
//---------------------------------------------------------------------------  
void EnableWDT(int interval)  
{
unsigned char bBuf;  
bBuf = Get_F81865_Reg(0x2B);  
bBuf &= (~0x20);  
Set_F81865_Reg(0x2B, bBuf);  
//Enable WDTO  
Set_F81865_LD(0x07);  
Set_F81865_Reg(0x30, 0x01);  
//switch to logic device 7  
//enable timer  
bBuf = Get_F81865_Reg(0xF5);  
bBuf &= (~0x0F);  
bBuf |= 0x52;  
Set_F81865_Reg(0xF5, bBuf);  
//count mode is second  
Set_F81865_Reg(0xF6, interval);  
//set timer  
bBuf = Get_F81865_Reg(0xFA);  
bBuf |= 0x01;  
Set_F81865_Reg(0xFA, bBuf);  
//enable WDTO output  
//start counting  
bBuf = Get_F81865_Reg(0xF5);  
bBuf |= 0x20;  
Set_F81865_Reg(0xF5, bBuf);  
}
//---------------------------------------------------------------------------  
void DisableWDT(void)  
{
unsigned char bBuf;  
Set_F81865_LD(0x07);  
//switch to logic device 7  
//disable WDTO output  
bBuf = Get_F81865_Reg(0xFA);  
bBuf &= ~0x01;  
Set_F81865_Reg(0xFA, bBuf);  
bBuf = Get_F81865_Reg(0xF5);  
bBuf &= ~0x20;  
bBuf |= 0x40;  
Set_F81865_Reg(0xF5, bBuf);  
//disable WDT  
}
//---------------------------------------------------------------------------  
66  
IB957 User’s Manual  
APPENDIX  
//---------------------------------------------------------------------------  
//  
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY  
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE  
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR  
// PURPOSE.  
//  
//---------------------------------------------------------------------------  
#include "F81865.H"  
#include <dos.h>  
//---------------------------------------------------------------------------  
unsigned int F81865_BASE;  
void Unlock_F81865 (void);  
void Lock_F81865 (void);  
//---------------------------------------------------------------------------  
unsigned int Init_F81865(void)  
{
unsigned int result;  
unsigned char ucDid;  
F81865_BASE = 0x4E;  
result = F81865_BASE;  
ucDid = Get_F81865_Reg(0x20);  
if (ucDid == 0x07)  
//Fintek 81865  
//Fintek 81865  
{
goto Init_Finish;  
}
F81865_BASE = 0x2E;  
result = F81865_BASE;  
ucDid = Get_F81865_Reg(0x20);  
if (ucDid == 0x07)  
{
goto Init_Finish;  
}
F81865_BASE = 0x00;  
result = F81865_BASE;  
Init_Finish:  
return (result);  
}
//---------------------------------------------------------------------------  
void Unlock_F81865 (void)  
{
outportb(F81865_INDEX_PORT, F81865_UNLOCK);  
outportb(F81865_INDEX_PORT, F81865_UNLOCK);  
}
//---------------------------------------------------------------------------  
void Lock_F81865 (void)  
{
outportb(F81865_INDEX_PORT, F81865_LOCK);  
}
//---------------------------------------------------------------------------  
void Set_F81865_LD( unsigned char LD)  
{
Unlock_F81865();  
outportb(F81865_INDEX_PORT, F81865_REG_LD);  
outportb(F81865_DATA_PORT, LD);  
Lock_F81865();  
}
//---------------------------------------------------------------------------  
void Set_F81865_Reg( unsigned char REG, unsigned char DATA)  
{
Unlock_F81865();  
outportb(F81865_INDEX_PORT, REG);  
outportb(F81865_DATA_PORT, DATA);  
Lock_F81865();  
}
//---------------------------------------------------------------------------  
IB957 User’s Manual  
67  
APPENDIX  
unsigned char Get_F81865_Reg(unsigned char REG)  
{
unsigned char Result;  
Unlock_F81865();  
outportb(F81865_INDEX_PORT, REG);  
Result = inportb(F81865_DATA_PORT);  
Lock_F81865();  
return Result;  
}
//---------------------------------------------------------------------------  
//---------------------------------------------------------------------------  
//  
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY  
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE  
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR  
// PURPOSE.  
//  
//---------------------------------------------------------------------------  
#ifndef __F81865_H  
#define __F81865_H  
1
//---------------------------------------------------------------------------  
#define  
#define  
F81865_INDEX_PORT  
F81865_DATA_PORT  
(F81865_BASE)  
(F81865_BASE+1)  
//---------------------------------------------------------------------------  
#define F81865_REG_LD 0x07  
//---------------------------------------------------------------------------  
#define F81865_UNLOCK 0x87  
#define F81865_LOCK  
0xAA  
//---------------------------------------------------------------------------  
unsigned int Init_F81865(void);  
void Set_F81865_LD( unsigned char);  
void Set_F81865_Reg( unsigned char, unsigned char);  
unsigned char Get_F81865_Reg( unsigned char);  
//---------------------------------------------------------------------------  
#endif //__F81865_H  
68  
IB957 User’s Manual  

Memorex MT2252S MT2271S User Manual
NEC NDH 160 User Manual
Panasonic Cordless Phones With Answering Machine KXTG7644M User Manual
Panasonic CT 32HX40 User Manual
Panasonic VCR PV M1326 User Manual
Parkinson Cowan Libra User Manual
Philips 21PT5525 User Manual
Philips 28PT7138 User Manual
Philips 100Hz TV User Manual
Philips PRF227S PLW225S User Manual