Indesit KD643G User Manual

Free Standing Gas Cooker  
Instructions for installation and use  
KD643G  
KD641G  
KD640G  
Introduction  
To help you make the best use of your cooker, PLEASE READ THIS BOOKLET  
CAREFULLY.  
Your new cooker is guaranteed and will give lasting service. The guarantee is only  
applicable if the cooker has been installed in accordance with the Installation  
Instructions.  
The cooker is designed specifically for domestic use and responsibility will not be  
accepted for use in any other installation.  
When first using the cooker ensure that the room is well ventilated (e.g. open a  
window or use an extractor fan) and that persons who may be sensitive to the odour  
avoid any fumes. It is suggested that any pets be removed from the room until the  
smell has ceased. This odour is due to any temporary finish and also any moisture  
absorbed by the insulation.  
Our policy is one of continual improvement in design and development,  
therefore strict accuracy of illustrations and descriptions cannot be  
guaranteed.  
This appliance conforms to the following EEC Directives:  
Gas Appiances  
90/396/EEC  
Electromagnetic Compatibility  
89/336/EEC  
92/31/EEC  
Low Voltage Equipment  
73/23/EEC  
93/68/EEC  
93/68/EEC  
3
Safety Information  
Please read the precautions below before using your cooker.  
ALWAYS . . .  
ALWAYS make sure you understand the controls before using the cooker.  
ALWAYS check that all controls on the cooker are turned off after use.  
ALWAYS stand back when opening an oven door to allow heat to disperse.  
ALWAYS use dry, good quality oven gloves when removing items from the ovens.  
ALWAYS take care when removing items from the top oven/grill when the main  
oven is on, as the contents may be hot.  
ALWAYS keep the oven and grill doors closed when the cooker is not in use.  
ALWAYS place pans centrally over the hotplate burners and position them so  
that the handles cannot accidentally be caught or knocked or become  
heated by other burners.  
ALWAYS keep the cooker clean, as a build up of grease or fat from cooking can  
cause a fire.  
ALWAYS allow the cooker to cool before cleaning.  
ALWAYS follow the basic principles of food handling and hygiene to prevent the  
possibility of bacterial growth.  
ALWAYS keep ventilation slots clear of obstructions.  
ALWAYS turn off the electricity supply before cleaning or replacing the oven  
lamp.  
ALWAYS refer servicing to CORGI registered appliance service engineers.  
4
Safety Information  
NEVER . . .  
NEVER leave children unsupervised where the cooker is installed as all surfaces  
will get hot during and after use.  
NEVER allow anyone to sit or stand on any part of the cooker.  
NEVER store items that children may attempt to reach above the cooker.  
NEVER heat up unopened food containers as pressure can build up causing  
the container to burst.  
NEVER store chemicals, food stuffs, pressurised containers in or on the cooker,  
or in cabinets immediately above or next to the cooker.  
NEVER fill a deep fat frying pan more than 1/3 full of oil, and never use a lid.  
DO NOT LEAVE UNATTENDED WHILE COOKING.  
NEVER place flammable or plastic items on or near the hotplate.  
NEVER use proprietary spillage collectors on the hotplate.  
NEVER use the cooker as a room heater.  
NEVER dry clothes or place other times over or near to the hotplate or oven/  
grill doors.  
NEVER wear garments with long flowing sleeves whilst cooking.  
NOTE: The use of a gas cooking appliance results in the production of heat and  
moisture in the room in which it is installed. Always ensure that the kitchen is well  
ventilated; keep natural ventilation holes open or install a mechanical ventilation  
device (mechanical extractor hood).  
In particular when using the grill or more than one hotplate burner, open a window if  
a mechanical ventilation device is not operating.  
5
Oven Timer Operation (KD643G only)  
The oven timer offers you the following features:  
1. Time of Day  
2. Automatic Cooking  
3. Minute Minder  
AUTOMATIC COOKING  
The main oven can be controlled automatically.  
GUIDANCE ON AUTOMATIC COOKING  
1. Select foods which will take the same time to cook.  
2. Set the oven timer so that the food has just finished or is just about to finish  
cooking on your return to the oven. This will ensure the food has not cooled  
down and does not require reheating before serving.  
3. Food should be as cold as possible when it goes into the oven, ideally  
straight from the refrigerator. Frozen meat and poultry should be thawed  
thoroughly before it is put in the oven.  
4. Warm food should never be placed in the oven if there is to be a  
delay period. Stews prepared by frying the meat and vegetables should be  
cooked as soon as possible.  
5. Dishes containing left-over cooked poultry or meat, for example  
Shepherds Pie, should not be cooked automatically if there is to be a delay  
period.  
6. Stews and joints should be cooked by the long slow method, so that the delay  
period is kept to a minimum.  
7. On warm days, to prevent harmful bacterial growth in certain foods (ie poultry,  
joints, etc) the delayed start should be kept to a minimum.  
8. Wine or beer may ferment and cream may curdle during the delay period, so it  
is best to add these ingredients just before serving.  
9. Foods which discolour should be protected by coating in fat or tossing in water  
to which lemon juice has been added, prior to placing food in the oven.  
10. Dishes containing liquid should not be filled too full to prevent boiling over.  
11. Food should be well sealed (but not airtight) in a container to prevent the loss  
of liquid during cooking. Aluminium foil gives a good seal.  
12. Ensure food is cooked thoroughly before serving.  
6
(KD643G only)  
Know your Timer  
CLOCKFACE  
The timer incorporates a 24 hour clock.  
Ensure the correct time of day is always set, before using your cooker.  
SYMBOLS  
A ‘bell’ symbol will light up when you select a Minute Minder Period and will  
remain lit for the period set.  
At the end of the Minute Minder Period, the timer will emit an audible tone and  
the ‘bell’ symbol will disappear.  
The ‘cookpot’ symbol will light up either:–  
When the timer is in manual mode, or  
During the actual Cook Period.  
‘AUTO’ will light up:–  
When the timer is first turned on it will flash. It will go out when a time of day  
is set or when the timer is set to manual.  
The ‘AUTO’ symbol will flash at the end of an Auto Cooking programme to indi-  
cate that the programme has finished.  
(When the ‘AUTO’ symbol is flashing, to return the oven to Manual operation,  
turn the oven controls off, ensure that the correct time of day is set, and press  
the “Manual” button – The ‘AUTO’ symbol will go out).  
TIMER FUNCTION BUTTONS  
Minute Minder  
Button  
Here you can set a time period of up to 23 hours 59 minutes, that will count down.  
When it reaches zero, the timer will emit an audible tone.  
For Example: If you set 20 minutes, the audible tone will occur 20 minutes later.  
AUTO COOKING PROGRAMME  
Cook Period Button Cook Period is the actual length of time for which, the timer will switch the oven(s)  
on as part of an “Auto Cooking” programme.  
(e.g. If you set 2 hours, the food will be cooked for 2 hours).  
End Time Button  
The time of day at which you want an “Auto Cooking” programme to end.  
For Example: If you set a “Cook Period” for 2 hours, and “End Time” of 11:00. The  
timer will switch the oven(s) on at 9:00 and turn the oven(s) off at 11:00. You will hear  
a audible tone at 11:00, to indicate that the Auto Cooking Programme has finished.  
Notes:  
-
When setting an Auto Cooking programme you will need to set the oven  
control(s) to the required temperature(s) when you set the timer.  
If an Auto Cooking programme has been set the oven(s) will only operate during  
the pre-programmed time.  
-
Manual Button  
Needs to be pressed to cancel an Auto Cooking programme and return the oven(s) to  
Manual operation.  
“+” and “–” Buttons Used to adjust the various timer function settings.  
7
Electronic Clock & Automatic Oven Timer  
(KD643G only)  
Operation  
SETTING THE TIME OF DAY  
Step 1 Make sure all oven controls are turned Off.  
Step 2 Check the electricity supply to the cooker is turned on.  
Step 3 When switched on the display will show 0.00 and the Auto symbol,  
flashing intermittently.  
Step 4 Press & hold in both the Cook Period & End Time buttons together.  
Step 5 With the Cook Period & End Time buttons still held in, press either the “+”  
or “–” buttons to set the correct time of day.  
Step 6 Release all the buttons simultaneously.  
THE TIME OF DAY IS NOW SET.  
To change the time of day repeat Steps 4, 5 & 6 above.  
Note: You cannot adjust the time of day if the timer has been set for an  
Auto Cooking Programme.  
SETTING THE MINUTE MINDER  
Step 1 Ensure the time of day is set correctly.  
Step 2 Press and hold the Minute Minder button.  
Step 3 With the Minute Minder button held in, set the required Minute Minder  
period using the “+” and “–” buttons. A ‘bell’ symbol will light up.  
Release all buttons and the timer display will revert back to the time of day.  
The ‘bell’ symbol will remain lit to signify that a Minute Minder period has been  
set.  
At the end of the set time an audible tone will be heard, and the ‘bell’ symbol will  
disappear.  
Step 4 To cancel the audible tone press the Minute Minder button.  
Note 1 When the Minute Minder has been set, the time remaining can be checked at any  
time by simply pressing the Minute Minder button.  
Note 2 If necessary the Minute Minder can be cancelled before the tone sounds by  
pressing and holding the Minute Minder button and then at the same time  
pressing the “–” button until 0.00 appears in the display window.  
8
Electronic Clock & Automatic Oven Timer  
(KD643G only)  
Operation  
AUTO COOKING PROGRAMMES  
There are two Auto Cooking programmes that can be selected using your timer:–  
(a) To set the timer to switch the oven(s) On and Off Automatically  
(b) To set timer to switch on immediately and OFF automatically after a set cook period.  
a) TO SET THE TIMER TO SWITCH THE OVEN(S) ON AND OFF AUTOMATICALLY  
This allows you to cook at a specified time for a chosen period before the oven switches  
off Automatically.  
Step 1 Check that the correct time of day is set, if not follow instructions for setting the time of day.  
Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).  
Step 3 Press and hold in the Cook Period button.  
The display will read 0.00 with the ‘cookpot’ symbol lit.  
Step 4 With the Cook Period button still held in, set the required Cook Period  
using the “+” and “–” buttons.  
Release the buttons and the timer display will revert to the time of day with the  
‘Auto’ symbol and ‘cookpot’ symbol lit.  
Step 5 Press and hold in the End Time button.  
The display will read the earliest possible end time for the Cook Period  
that you have set above.  
The ‘Auto’ symbol and ‘cookpot’ symbol will be lit.  
Step 6 With the End Time button still held in, use the “+” and “–” buttons to set  
the ‘End Time’ (i.e. The time you require the oven to switch off).  
Release all the buttons and the timer will revert back to the time of day.  
The ‘Auto’ symbol will remain lit to signify that an Auto Cooking Programme has  
been set. The ‘cookpot’ symbol will go out.  
Step 7 Turn the oven control(s) to the required temperature, and if necessary  
select the appropriate oven function.  
At the end of the Automatic Cook Period the Auto Symbol will flash and an  
intermittent bleeping sound will be heard.  
The audible tone will continue unless cancelled.  
The ‘Auto’ symbol will continue to flash until the timer is returned to Manual  
operation (see below).  
Step 8 Press the Manual button, the audible tone will be cancelled and the  
oven(s) will be returned to Manual.  
Step 9 Turn the oven control(s) to the OFF position.  
9
Electronic Clock & Automatic Oven Timer  
(KD643G only)  
Operation  
Note 1 When cooking automatically the Cook Period can be checked at any time by simply  
pressing the Cook Period button.  
Note 2 When cooking automatically the End Time can be checked at any time by simply  
pressing the End Time button.  
b) TO SET TIMER TO SWITCH ON IMMEDIATELY AND OFF AUTOMATICALLY AFTER A SET COOK  
PERIOD  
Step 1 Check that the correct time of day is set, if not follow instructions for setting the time of day.  
Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).  
Step 3 Turn the oven control(s) to the required temperature, and if necessary select the appropriate oven  
function.  
Step 4 Press & hold in the Cook Period button, the display will read 0.00 and the  
‘cookpot’ symbol will light up.  
With the Cook Period button still held in set the required Cook Period using the  
“+” and “–” buttons. Example: 1hr 30 minutes (as shown).  
Note: Cook Period is the length of time the food requires to cook.  
Step 5 Release all buttons.  
The timer display will revert to the time of day with the ‘Auto’ symbol lit &  
‘cookpot‘ symbol remaining lit.  
At the end of the Cook Period the ‘Auto’ symbol will flash and an intermittent  
audible tone will be heard.  
NOTE: The Cookpot symbol disappears  
The audible tone will continue until cancelled. The ‘Auto’ symbol will continue to  
flash until the timer is returned to Manual operation (see below).  
Step 6 Press the Manual button. The audible tone will be cancelled and the  
oven(s) will be returned to Manual.  
Step 7 Turn the oven control(s) to the OFF position.  
10  
Electronic Clock & Automatic Oven Timer  
(KD643G only)  
Operation  
TO CANCEL AN AUTO COOKING PROGRAMME BEFORE  
THE COOK PERIOD HAS FINISHED.  
Step 1 Turn the oven control(s) to the OFF position.  
Step 2 Press the Manual button to return the oven(s) to “Manual” operation.  
The ‘Auto’ symbol will go out.  
Note 1  
When cooking automatically the Cook Period can be checked at any time by simply pressing  
the Cook Period button.  
OTHER NOTES ON TIMER OPERATION  
1. When cooking Automatically the Cook Period can be checked at any time simply by pressing the Cook  
Period button.  
2. When cooking Automatically the End Time can be checked at any time by simply pressing the End Time  
button.  
3. Having set a Cook Period and End Time an electronic device stores the information. The device within the  
timer will switch the oven(s) on and off at the required times.  
4. When setting an Auto Cooking Programme and a mistake is made, to clear:–  
(a) Press & release the Manual button.  
(b) Start the sequence again.  
5. If at any time the display shows three flashing zero’s 0.00 and ‘Auto, it is likely that the electricity supply to  
the oven has been interrupted. Reset the timer to the correct time of day.  
Food in the oven may, therefore, not have been cooked, before serving check food is thoroughly heated  
and completely cooked.  
6. To set each function always press and hold the required function button and at the same time press “+” or  
“–” buttons.  
11  
Hotplate  
ALWAYS PUSH IN THE CONROLS WHEN TURNING ANY OF THE BURNERS ON OR OFF.  
The hotplate has two high speed burners and two simmering burners which will  
accommodate pans between 100mm (4”) and 230mm (9”) diameter. All pans  
should be positioned centrally over the burners.  
TO USE THE HOTPLATE  
1. Press the ignition button and then push in and turn the control knob of the  
chosen burner anti-clockwise to the large flame symbol. Continue to press  
the ignition button until the sparks light the gas.  
2. Turn the control knob anti-clockwise to the desired setting.  
Only turn the control knob between the large flame symbol and the small  
flame symbol for adjusting the setting.  
3. To turn off, turn the control knob fully clockwise to the symbol O.  
DO NOT use the hotplate unless all pan supports are in position.  
DO NOT use mis-shapen pans which may be unstable.  
DO NOT use round base woks directly on the pan supports.  
Each burner is fitted with a spark ignitor for lighting the gas. To ensure rapid lighting of  
the burners every time they are used, the ignitors must be kept clean and dry. Remove  
any food spillage or cleaning materials from the ignitor using a small nylon brush such  
as a tooth brush. Access to the ignitor can be achieved by lifting off the loose burner  
parts carefully when the burners are cool.  
When the hotplate burner bodies and caps are removed for cleaning, be careful not to  
drop any food particles or cleaning materials into the burner bases, to avoid the  
possibility of blocking the gas jets.  
If aluminium based pans are used, a silvery deposit may appear on the top edge of the  
pan support fingers. See ‘Care and Cleaning’ section for cleaning information.  
When the hotplate burners are turned down, a slight ‘popping’ noise may be heard. This  
is perfectly normal.  
12  
Hotplate  
SAFETY REQUIREMENTS FOR DEEP FAT FRYING  
1. Never fill chip pans more than one third full with oil or fat.  
2. Never leave oil or fat unattended during the heating or cooling period.  
3. Never heat fat or fry with a lid on the pan.  
4. Always dry food thoroughly before frying, and lower it slowly into the  
hot oil or fat. Frozen foods in particular will cause frothing and spitting if  
added too quickly.  
5. Always keep the outside of the pan clean and free from streaks of oil or  
fat.  
HOW TO DEAL WITH A FAT FIRE  
1. Do not move the pan.  
2. Turn off the hotplate burners.  
3. Smother the flames with a fire blanket or damp cloth to extinguish the  
fire. Do not use water or a fire extinguisher as the force of it may  
spread the burning fat or oil over the edge of the pan.  
4. Leave the pan for at least 60 minutes before moving it.  
13  
Grill  
ALWAYS PUSH IN THE CONROLS WHEN TURNING ANY OF THE BURNERS ON OR OFF.  
CAUTION – ACCESSIBLE PARTS MAY BECOME HOT WHEN THE GRILL IS USED.  
YOUNG CHILDREN SHOULD BE KEPT AWAY.  
GRILL PAN AND HANDLE: The grill pan handle is detachable from the pan to facilitate  
cleaning and storage. The handle can be fixed as follows :  
1. Remove the screw and washer from the grill pan bracket.  
2. Tilt the handle over the recess. (A)  
3. Slide the handle towards the centre of the pan. (B)  
4. Locate the handle over the bracket. (C)  
For a fixed handle, replace the screw and washer and ensure they are fully tightened.If  
a detachable handle is required, do not replace the screw and washer.  
Warning : Ensure when using the grill pan handle in the detachable manner it is  
centralised and secure.  
The grill pan can be stored in the top compartment with the handle attached by  
placing the shelf in the middle or lower position and tilting the grill pan over the rear  
edge of the shelf.  
A
B
C
TO USE THE GRILL  
1. Check that the electricity supply is switched on.  
2. Open the top oven/grill door and remove the grill pan.  
3. Remove the heat shield from the rear of the shelf for maximum grilling area.  
4. Place shelf in chosen position. Refer to grilling chart.  
5. Press the ignition button and then push in and turn the control knob clockwise to  
the large flame symbol. Continue to press the ignition button until the sparks light  
the gas.  
6. Slide the grill pan along the shelf towards the rear of the grill compartment  
until it stops.  
7. Turn the control knob to the desired setting. Only turn the control knob between  
the large flame symbol and the small flame symbol when adjusting the setting.  
8. To turn off, turn the control knob anti-clockwise to the symbol O.  
Models: KD643G and KD641G only:  
The grill cannot be used at the same time as the top oven.  
An odour may be noticed when first using the grill – this should cease after a short  
period of use.  
DO NOT use the grill with the door closed.  
DO NOT cover the grill pan or grid with aluminium foil as this can hold fat, intensify  
the heat and create a fire hazard.  
RELIGHTING THE BURNER  
In the event of the burner flames being accidentally extinguished, turn off the burner  
control and do not attempt to re-ignite the burner for at least one minute.  
14  
Grill  
Grilling can be started from cold but for best results preheat for approximately two  
minutes. Most cooking is done with the heat on full, but it may be desirable to reduce  
it for thicker pieces of meat or for keeping food warm.  
Models KD643G and KD641G only: There are 5 shelf positions available for grilling.  
Model KD640G: There are 2 shelf positions available for grilling.  
For au gratin dishes eg. Macaroni Cheese and meringue toppings eg. Baked Alaska,  
place the dish on the floor of the grill compartment. The base of the grill pan can be  
used for warming fruit garnishes on the reduced setting.  
REMOVE HEAT SHIELD  
FROM SHELF WHEN  
GRILLING FOR MAXIMUM  
GRILLING AREA.  
Model KD640G only: The shelf is not required in this model - The shelf supports have  
been designed to hold the grill pan, therefore place the grill pan directly onto the  
runners in the required position.  
NOTE: Strong detergents used in dishwashers may damage the grill pan grid  
finish; clean in soapy water as described in CARE AND CLEANING section.  
Always ensure that the grill pan handle is correctly fitted to the grill pan.  
If necessary tighten any loose screws with a screwdriver.  
15  
Main Oven  
ALWAYS PUSH IN THE CONROLS WHEN TURNING ANY OF THE BURNERS ON OR OFF.  
The oven has different heat zones – the thermostat settings refer to the temperature on the  
middle shelf position; above this shelf it is hotter and below it is cooler.  
Two shelves provide five possible cooking levels enabling full use of the different  
temperatures inside the oven.  
Each shelf has a safety stop to prevent if from being pulled out too far when attending to food.  
Shelves are removed from the oven by pulling them out to the stop and then lifting them at the  
front to withdraw.  
The baking dish and grill pan without the handle can be used in the oven.  
The maximum size of baking tray that should be used is 300mm x 350mm (12” x 14”).  
TO USE THE MAIN OVEN  
1.  
Check that the electricity supply is switched on and the timer (KD643G only) is set to  
manual mode .  
2.  
3.  
Place oven shelves in the chosen positions (refer to cooking charts).  
Push in and turn the oven control knob fully anti-clockwise. Sparking will continue until  
the burner is lit.  
4.  
5.  
Turn the control knob clockwise to the required setting (refer to cooking chart). There is a  
delay of about one minute whilst the safety device operates before the burner comes on  
full.  
To turn off, turn the control knob fully clockwise to the symbol O.  
Never place dishes on the oven base over the burner.  
An odour may be noticed when first using the oven – this should cease after a short period of  
use.  
COLD START COOKING  
Anything requiring long slow cooking such as casseroles and rich fruit cakes can be put into a  
cold oven. Satisfactory results can also be obtained with creamed mixture, rich pastries or yeast  
mixtures, but for perfection we recommend preheating the oven for about 15 minutes at the  
gas mark you require for cooking.  
ROASTING OF LARGE POULTRY  
The maximum weight of poultry that can be accommodated is 11.5kg (25 lbs) of suitable shape.  
It is important to check that the bird DOES NOT overhang the burner at the back of the oven.  
STORAGE AND RE-HEATING OF FOOD  
It is vitally important to strictly adhere to the basic principles of food handling and hygiene to  
prevent the possibility of bacterial growth.  
1. If food is to be frozen or not served immediately, cool it in a clean container  
as quickly as possible.  
2. Completely thaw frozen food in the refrigerator before re-heating.  
3. Re-heat food thoroughly and quickly either on the hotplate or in a hot oven,  
Mk. 6, and then serve immediately.  
4. Only re-heat food once.  
‘COOK CHILL’ DISHES  
These should always be placed in a pre-heated oven ideally on the first or  
second shelf position. Follow the packet instructions for cooking time.  
16  
Main Oven Cooking Chart  
The following times and setting are for guidance only. You may wish to alter the setting to give a  
result more to your satisfaction. When a different setting to that shown below is given in a recipe, the  
recipe instructions should be followed. Allow 15 minutes preheat for best results.  
Always turn the thermostat knob to Mark 9 before selecting the required Gas Mark.  
Shelf position 1 is the highest.  
Gas  
Mark  
Shelf  
Positions  
Food  
Approx. Cooking Time and Comments  
STARTERS  
Patés and Terrines  
FISH  
1
2
3 or 4  
4
1 / - 2 hrs  
25 mins - 1 hr, depending on recipe  
and size of fish  
Oily Fish (whole)  
4 or 5  
4 or 5  
3
3
White Fish (fillets & steaks)  
25 - 30 mins.  
MEAT AND POULTRY  
Veal  
5
4
25 mins per lb + 25 mins  
Beef  
4 or 5  
4
25 - 30 mins per lb + 25 mins  
40 mins per lb covered in foil  
+ 40 mins per lb uncovered  
Ham  
5
4
Lamb  
5
4
30 - 35 mins per lb + 30 mins  
40 mins per lb + 40 mins  
25 mins per lb + 25 mins  
25 mins per lb + 25 mins  
15 - 20 mins per lb + 20 mins  
Pork  
5
4
4
Chicken  
Duckling & gosling  
Turkey  
5
5
4 or 5  
6
4
4 or 5  
4
50 mins. Remove bacon for last 15 mins.  
Add extra 15 mins if roasting brace  
Game birds  
Casseroles  
1
2
3
3 or 4  
1 / - 6 hrs. (depending on type of meat)  
PUDDINGS  
1
1
4
2
2 / - 2 / hrs stand dish on a baking tray and  
Milk Puddings  
3
3 or 4  
started with warm milk  
Baked Custard  
3
3 or 4  
45 mins in bain-marie  
40 - 50 mins  
Baked sponges  
4
3
30 - 45 mins depending on the size  
and type of apples  
Baked Apples  
3
1
4
4 or 5  
3
Meringue puddings  
Apple Pie 1x9" (230mm)  
Fruit crumbles  
15 mins or until 'tinged' with brown  
45 - 55 mins stand dish on a baking tray  
35 - 45 mins  
6
5 or 6  
3
ALUMINIUM FOIL  
If using Aluminium Foil, remember that it is important to increase the cooking time by one third.  
NEVER  
1. Allow the foil to touch the sides of the oven.  
2. Cover the oven interior with foil.  
3. Cover the oven shelves with foil.  
17  
Main Oven Cooking Chart  
Gas  
Mark  
Shelf  
Positions  
Food  
Approx. Cooking Time and Comments  
CAKES, PASTRIES AND BISCUITS  
Small cakes - 2 trays  
5
5
4
5
2
4
2
6
5
7
1 & 3  
2
17 - 25 mins  
"
- 1 tray  
Victoria sandwich 2x8" (205mm)  
1 & 3  
2
25 - 35 mins  
Fatless sponge 2x7" (180mm) -  
3 egg mix  
20 - 25 mins. 2 tins side by side  
1
2
Christmas cake  
3 or 4  
3
4 - 6 / hrs depending on recipe  
1
1
4
2
Madeira cake 7" (180mm)  
Rich Fruit cake 9" (230mm)  
Shortcrust pastry  
1 / - 1 / hrs  
1
2
3
3 - 3 / hrs.  
2 or 3  
2
15 mins - 1 hr depending on recipe  
20 - 40 mins depending on recipe  
10 - 30 mins depending on recipe  
Rich Shortcrust pastry - 1 tray  
Flaky & puff pastry - 2 trays  
- 1 tray  
1 & 3  
2 or 3  
2
"
"
"
"
Choux pastry - éclairs 1 tray  
Scones - 2 trays  
6
7
35 - 40 mins  
10 - 15 mins  
"
1 & 3  
2 or 3  
4
- 1 tray  
Shortbread - 7" (180mm) round  
Biscuits - 2 trays  
2
4
55 - 1hr depending on thickness  
15 - 20 mins depending on recipe  
1 & 3  
2
- 1 tray  
"
"
"
"
YEAST MIXTURES  
Bread  
7 or 8  
7 or 8  
5
3
45 - 50 mins  
15 - 20 mins  
30 - 40 mins  
Rolls  
2 or 3  
2 or 3  
Chelsea buns  
MISCELLANEOUS  
Yorkshire Pudding - large  
7
7
4
1 or 2  
1 or 2  
3
45 - 50 mins  
25 - 30 mins  
30 mins  
- individual  
Soufflés  
2 - 5 hrs starting on shelf 4 until 'set'  
and then on the baseplate until dried  
out - turn when necessary.  
Meringues  
Slow Cook  
4 &  
baseplate  
1
2
Baked Potatoes  
4 or 5  
3
1 / - 3 hrs until soft, depending on size  
When baking with two trays or tins on two levels, the top tray is removed first and the lower tray moved up to the  
top position for a few minutes longer.  
Soft Margarine – Use the oven settings recommended by the margarine manufacturer and not those indicated on  
the cooking chart.  
18  
The ‘Slow Cook’ Setting  
The ‘Slow Cook’ setting is used for slow cooking, keeping food warm and warming plates  
for short periods. Set the main oven thermostat to ‘S’ or ‘90˚C.  
USING THE ‘SLOW COOK’ SETTING FOR SLOW COOKING  
1. All dishes cooked by the ‘Slow Cook’ setting should be cooked for a minimum 6  
hours. They will ‘hold’ at this setting for a further hour but marked deterioration in  
appearance will be noticed in some cases.  
2. Joints of meat and poultry should be cooked at Mk. 6 for 30 minutes before  
turning to the ‘Slow Cook’ setting and never be cooked lower than the middle shelf  
position.  
3. Joints of meat over 6 lbs (2.7kg) and poultry over 4 lbs 8oz (2 kg) should not  
be cooked using the ‘Slow Cook’ setting.  
4. Always stand covered joints on a rack over the meat tin to allow good air  
circulation.  
5. A meat thermometer should be used when cooking pork joints and poultry.  
The internal temperature of the food should reach at least 88˚C.  
6. This method is unsuitable for stuffed meat and stuffed poultry.  
7. Always bring soups, casseroles and liquids to the boil before putting in the  
oven.  
8. Cover casseroles with foil and then the lid to prevent loss of moisture.  
9. Always thaw frozen food completely before cooking.  
10. Root vegetables will cook better if cut into small pieces.  
11. Adjust seasonings and thickenings at the end of the cooking time.  
12. Use the zones of heat in the oven, e.g. meringues and milk puddings can be  
cooked lower in the oven whilst other dishes requiring greater heat can be  
cooked above them.  
13. Egg and fish dishes need only 1-5 hours cooking and should be included in  
day cooking sessions, when they can be observed from time to time.  
14. Dried red kidney beans must be boiled for a minimum of ten minutes after  
soaking, before inclusion in any dish.  
19  
Top Oven (KD643G and KD641G only...)  
ALWAYS PUSH IN THE CONROLS WHEN TURNING ANY OF THE BURNERS ON OR OFF.  
The top oven can be used to cook small quantities of food or used in conjunction with  
the main oven to provide additional cooking space.  
The shelf in the top oven has a heat shield fitted at the rear. The shield can be removed  
for cleaning and grilling, but must be replaced when using the oven.  
The shelf can be used in five different positions, because these shelf positions are so  
close: Shelf position 1 is the highest, 2 is central and 3 is the lowest shelf position  
referred to in the cooking charts on pages 21 and 22.  
It has a safety stop to prevent it from being pulled out too far when attending to food.  
The shelf is removed from the oven by pulling it out to the stop and then lifting at the  
front to withdraw.  
The baking dish and grill pan without the handle can be used in the oven. The  
maximum size of baking tray that should be used is 300mm x 350mm (12” x 14”).  
TO USE THE TOP OVEN  
1. Check that the heat shield is fitted to the shelf.  
2. Place the top oven shelf in the chosen position (refer to cooking chart).  
3. Push in and turn the top oven/grill control fully anti-clockwise:  
- Model number KD643G, sparking will continue until burner is lit.  
- Model number KD641G, Press the ignition button until the sparks light the gas.  
4. Turn the control knob clockwise to the required setting (refer to cooking  
chart).  
5. There is a delay of about one minute whilst the safety device operates before the  
burner comes on full.  
6. To turn off, turn the control knob clockwise to the symbol O.  
NOTE: It is normal for a slight resistance to be felt when turning the control knob  
to the oven settings.  
GUIDANCE ON USING THE TOP OVEN  
1. Best results are obtained by pre-heating the oven for about 15 minutes.  
2. The tray or dish on which the food is to be cooked, should be pushed to the  
back of the shelf.  
3. Food which is higher than or will rise above 125mm (5”) cannot be cooked  
in the top oven.  
Never place dishes on the oven base over the burner.  
An odour may be noticed when first using the oven – this should cease after a short  
period of use.  
20  
Top Oven Cooking Chart (KD643G and KD641G only...)  
The following times and setting are for guidance only. You may wish to alter the setting to give a  
result more to your satisfaction. When a different setting to that shown below is given in a recipe, the  
recipe instructions should be followed. Allow 15 minutes preheat for best results. Always turn the  
thermostat knob to Mark 1 before selecting the required gas Mark.  
Shelf position 1 is the highest, 2 is central and 3 is the lowest position.  
Gas  
Shelf  
Food  
Mark  
Position  
Approx. Cooking Time and Comments  
20-30 mins.  
Push dish right to  
back of shelf.  
FISH  
Oily and white fish  
MEAT AND POULTRY  
Beef (medium)  
Ham (covered in foil)  
Lamb  
5
2
4 or 5  
3
3
3
3
3
3
3
25-30 mins per lb + 25-30 mins  
40 mins per lb + 40 mins  
5
5
5
5
5
4
3
30-35 mins per lb + 30 mins  
40 mins per lb + 40 mins  
Pork  
Chicken  
25 mins per lb + 25 mins  
Duckling & Goose  
Turkey  
25 mins per lb + 25 mins  
15-20 mins per lb + 15-20 mins  
2-4 hrs. depending on meat used.  
Casseroles  
3
VEGETABLES  
1
2
Baked jacket potatoes  
PUDDINGS  
5
2
1 / - 2 hrs.  
1
2
Milk Puddings (500ml/1pt)  
Baked Custard (500ml/1pt)  
Baked Sponge Puddings  
Baked Apples  
3
3
4
3
1
6
5
2
2
2
2
2
2
2
1 / - 2 hrs.  
45 mins - 1 hr. in bain-marie of cold water.  
30 - 45 mins  
45 mins - 1 hr. depending on size  
25 mins until tinged with brown  
60 mins  
Meringue Topped Puddings  
Apple Tart (1 x 205mm/8”)  
Fruit Crumble  
45 - 50 mins  
If using aluminium foil:  
1. Remember it is important to increase the cooking time by one third.  
2. Do not allow the foil to touch the sides of the oven.  
3. Do not cover the oven interior with foil.  
4. Do not cover the oven shelves with foil.  
21  
Top Oven Cooking Chart (KD643G and KD641G only...)  
Gas  
Mark  
Shelf  
Positions  
Food  
Approx. Cooking Time and Comments  
CAKES, PASTRIES AND BISCUITS  
Small Cakes (16 per tray)  
Victoria sandwich (2 x 180mm / 7”)  
Swiss Roll (3 egg quantity)  
Christmas cake (1 x 205mm / 8”)  
Madeira cake (1 x 180mm / 7”)  
Rich Fruit cake (1 x 180mm / 7”)  
Gingerbread  
5
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
20 - 25 mins.  
25 - 30 mins.  
6
10 - 12 mins.  
2
4 - 5 hrs depending on recipe  
1 hr.  
4
1
1
4
2
2
2 / - 2 / hrs.  
1
3
2
4
3
1 / - 1 / hrs.  
Scones - 16 per tray  
Shortbread (1 x 180mm / 7”)  
Biscuits  
7
12 - 15 mins.  
2
45 mins. – 1 hr. depending on thickness  
15 - 25 mins.  
4-6  
6
Shortcrust Pastry  
15 mins. – 1 hr. depending on recipe  
20 - 30 mins.  
Rich Short Crust  
5
Flaky/Puff Pastry  
7
10 - 30 mins. depending on recipe  
25 - 35 mins.  
Choux Pastry  
6
YEAST MIXTURES  
Bread - rolls, plait  
7
5
2 or 3  
C
25 - 35 mins  
25 - 30 mins  
Tea breads etc.  
MISCELLANEOUS  
Yorkshire Pudding  
- small  
- large  
7
7
1
2
2
3
20 - 25 mins  
30 - 40 mins  
1
2
Meringues  
2 / - 4 hrs. turn when necessary  
Soft Margarine – Use the oven settings recommended by the margarine manufacturer and not those  
indicated on the cooking chart.  
22  
Care and Cleaning  
Clean the cooker regularly and wipe up spills soon after they occur to prevent  
them from becoming burnt on.  
TURN OFF THE MAIN SWITCH AND ENSURE THE COOKER IS COLD BEFORE CLEANING.  
BEFORE SWITCHING ON AGAIN, ENSURE THAT ALL CONTROLS ARE IN THE OFF POSITION.  
NEVER USE BIOLOGICAL WASHING POWDER, CAUSTIC CLEANERS, HARSH ABRASIVES,  
SCOURING PADS, STEAM CLEANERS, AEROSOL CLEANERS OR OVEN CHEMICAL CLEANERS  
OF ANY KIND.  
Before moving your cooker ensure that it is cool and note that it is heavy  
(approximately 70 kg 155 lbs), so you may require assistance. To move the cooker  
forward, open the top oven/grill door and with both hands positioned under the roof  
of the compartment, lift and pull forward. Replace by pushing the cooker backwards.  
Check that the cooker is level. Take care to ensure that any floor covering is not  
damaged.  
MAIN OVEN HEAT CLEAN LININGS  
The oven roof and back linings are coated with a special enamel which has a continuous  
cleaning action. The higher the oven temperature the more effective the action. In most  
cases this cleaning operation will proceed during normal cooking. However, if roasting is  
done frequently, or high temperatures are not used regularly it may be necessary to run  
the oven empty at Mark 8 for about 2 hours.  
It should not normally be necessary to clean the linings with water, but if desired, wipe  
them over with a soapy cloth, followed by a wipe with a damp clean cloth.  
OVEN SHELF SUPPORTS  
Models KD643G and KD641G only:The shelf supports are removable  
and dishwasher safe.  
To remove hold the support at the front and pull away from the oven  
side, this can then be cleaned in a sink or a dishwasher.  
When removed it allows access to the oven side, which can be cleaned  
with warm soapy water.  
To refit the support, insert the longer leg into the rear fixing hole and  
push in the front leg.  
Model KD640G only: The grill (top cavity) shelves are fixed and should  
not be removed for cleaning. Wipe with a cloth wrung out in warm  
soapy water followed by a wipe with a damp clean cloth.  
23  
Care and Cleaning  
COOKER FINISH  
CLEANING METHOD  
Vitreous Enamel  
Hotplate, pan supports,  
hotplate front trim,  
burner caps, roasting dish,  
grill pan, main oven base,  
inside of grill compartment,  
inside of doors.  
Cloth wrung out in warm soapy water. Stubborn  
stains can be removed with a cream paste,  
liquid cleaner or by rubbing with fine steel wool  
soap pads.  
Check that the cleaning agent is approved by the  
Vitreous Enamel Association.  
Paint  
Side trims, plinth, fascia  
bottom trim, fascia end  
caps, side panels, door  
handles.  
Wash with a cloth wrung out in warm soapy water  
only.  
DO NOT USE ABRASIVES.  
Aluminium  
Similar to paint cleaning above. Use a nylon brush to  
remove any cleaning materials, water or dirt from the  
hotplate burner bodies.  
Hotplate side trims, hotplate  
burner bodies, lid rear trim,  
rear flue grille.  
Glass  
As for enamel cleaning. Polish with a clean dry cloth  
or kitchen roll.  
Chromium Plating  
Oven shelves, grill pan grid,  
grill pan handle support  
Wipe with a cloth wrung out in warm soapy water.  
A fine steel wool soap pad e.g. Brillo, Ajax, or a  
chrome or stainless steel cleaner may be used.  
Plastic  
Grill pan handle, control  
knobs  
Wipe with a cloth wrung out in warm soapy water.  
Stubborn stains can be removed with a cream  
cleaner.  
REPLACEMENT OF OVEN LIGHT BULB  
CAUTION: DISCONNECT THE APPLIANCE FROM THE ELECTRICITY SUPPLY BEFORE  
REPLACING THE LAMP TO AVOID THE POSSIBILITY OF AN ELECTRIC  
SHOCK  
Light bulbs are not covered by the manufacturer’s guarantee.  
A new 15W, 300˚C rated SES bulb can be obtained from your cooker supplier or any  
major electrical retailer.  
1. Remove the shelves from the oven.  
2. Unscrew the lens using a thick cloth to protect your fingers in the unlikely  
event of a lens fracture.  
3. Unscrew bulb.  
4. Fit new bulb and refit lens.  
24  
Care and Cleaning  
Take particular care not to damage the inner surface of the door inner glass that  
is coated with a heat reflective layer. Do not use scouring pads, or abrasive  
powder, which will scratch the glass. Ensure that the glass panel is not subjected  
to any sharp mechanical blows.  
Stubborn stains can be removed by using a fine steel wool soap pad. For slight soiling  
the inner glass panel may be cleaned, while still warm, without removing it from the  
door. After cleaning, rinse and dry with a soft cloth.  
CLEANING THE DOORS  
SIDE OPENING DOORS  
Cleaning the door glass is the same as the drop down doors, except take care to  
support the weight of the inner glass when removing and refitting.  
DROP DOWN DOORS  
Remove the door inner glass as follows.  
1.  
Open the door fully and unscrew the two screws securing the glass panel so  
that the securing brackets can be turned. There is no need to remove the  
screws completely.  
2.  
Turn the brackets so that the glass can be  
and cleaned at the sink (Fig. 1.)  
Fig. 1.  
3.  
The inside of the outer door glass can now be cleaned while still fitted to the  
cooker.  
NEVER OPERATE THE COOKER WITHOUT THE INNER DOOR GLASS  
IN POSITION.  
Refit the door inner glass as follows.  
1.  
2.  
NOTE: The inner door glass has a special reflective coating on one side.  
Replace the door inner glass so that the statement: “IMPORTANT THIS FACE  
TOWARDS THE OVEN” can be read from the inner side of the door.  
Turn the two securing brackets back to their  
original position to retain the glass and  
tighten the screws (Fig. 2.)  
Fig. 2.  
25  
Something Wrong with your Cooker?  
Before contacting your nearest Service Centre or Installer, check the problem  
guide below, there may be nothing wrong with your cooker.  
PROBLEM  
CHECK  
If all burners fail to ignite:  
Check that sparks appear at the burners; a clicking  
noise should be heard.  
Ignition does not work.  
Oven burner  
If not;  
Check that the electricity supply is turned on.  
If the electricity supply has failed, the hotplate, grill  
and top oven burners can be lit by a match.  
If only one burner fails to ignite:  
Burner ports  
Ignitor  
Check that the burner is dry and that spillage of food  
or cleaning fluid remains are not affecting the ignitor  
or burner ports.  
Grill burner  
Clean away any debris with a dry nylon brush such as  
an old toothbrush. If a wire wool pad has been used  
for cleaning around the burner ensure the ignitor is  
free from any stray strands. Any water on the burner  
should be dried with a cloth or kitchen towel.  
Burner ports  
Ignitor  
Hotplate burner.  
On the hotplate make sure that all the burner parts  
are correctly seated.  
Burner ports  
Ignitor  
26  
Something Wrong with your Cooker?  
PROBLEM  
CHECK  
Slight odour or small  
amount of smoke when  
grill / oven used first  
time  
This is normal and should cease after a short period.  
Check that the gas mark and shelf positions are as  
recommended in the Oven Cooking Charts.  
However, it may be necessary to increase or decrease the  
recommended setting slightly to suit your taste.  
Oven cooks too fast or too  
slow  
(KD643G only)  
Read the Timer instructions in this book carefully  
remembering that the Cook period is the length of time  
that the timer will switch the oven(s) on as part of an Auto  
Cooking Programme.  
Cannot set an “Auto Cook”  
programme or cannot get the  
timer to turn the oven on or  
off at the required times.  
The electricity supply to the cooker may have been been  
interrupted, but has now come back on again. set the  
correct time of day by following the instructions given in  
the timer section of this book.  
(KD643G only)  
Timer Display shows "0:00"  
with "Auto" Flashing.  
(KD643G only)  
The timer may be set for an Auto Cooking Programme.  
Check the timer to see if “AUTO” is illuminated. If it is,  
Main oven does not work, but  
the grill, top oven and hotplate follow the instructions given in the timer section of this  
burners work.  
book to cancel the Auto Cooking Programme.  
The oven lamp is not covered by the guarantee.  
The part is easily changed (see the section on oven lamp  
replacement). A new lamp may be obtained from our  
Parts department see Key Contacts (back page).  
Oven lamp does not  
work  
27  
Installation Instructions  
Prior to installation, ensure that the local distribution conditions (nature of the gas and  
gas pressure) and the adjustment conditions are compatible. The adjustment  
conditions for this appliance are stated on the data badge which is fitted on the back  
panel.  
This appliance is not designed to be connected to a combustion products evacuation  
device. It must be installed and connected in accordance with current installation  
regulations. particular attention should be given to the relevant requirements  
regarding ventilation.  
MODEL NUMBERS KD643G, KD641G and KD640G  
Category I2H (GB. IE)  
These models are set to burn NATURAL GAS (G20) at 20 mbar ONLY and can not be  
used on any other gas.  
GAS SAFETY (INSTALLATION & USE) REGULATIONS  
It is the law that all gas appliances are installed by competent persons in  
accordance with the current edition of the above regulations. It is in your interest and  
that of safety to ensure compliance with the law.  
In the UK, CORGI registered installers work to safe standards of practice.  
The cooker must also be installed in accordance with BS 6172.  
Failure to install the cooker correctly could invalidate the warranty liability claims and  
could lead to prosecution.  
LOCATION  
The cooker may be located in a kitchen, kitchen/diner or a bed-sitting room, but not in  
a room containing a bath or shower. The cooker must not be installed in a bed-sitting  
room of less than 20m3.  
PROVISION FOR VENTILATION  
The room containing the cooker should have an air supply in accordance with  
BS 5440: Part 2.  
The room must have an opening window or equivalent; some rooms may also require  
a permanent vent. If the room has a volume between 5 and 10m3, it will require an air  
vent of 50cm2 effective area unless it has a door which opens directly to outside. If the  
room has a volume of less than 5m3, it will require an air vent of 100cm2 effective area.  
If there are other fuel burning appliances in the same room, BS 5440: Part 2  
should be consulted to determine air vent requirements.  
28  
Installation Instructions  
TECHNICAL DATA  
DIMENSIONS  
Height  
Width  
Depth  
900 - 915mm  
600mm  
595mm (excluding door handles)  
GENERAL  
1
1
2
2
Gas connection  
Pressure test point  
Gas rate adjustment  
Aeration adjustment  
Rp / ( / ” BSP female)  
Grill injector  
None  
None  
Electrical connection  
Flexible cord fitted with a 3 pin 13 amp plug  
230/240V a.c. 50Hz. 3A fuse.  
NATURAL GAS  
HEAT INPUT  
INJECTOR  
BURNER  
HOTPLATE  
Front left and rear right  
3.0 kW  
1.9 kW  
128  
102  
HOTPLATE  
Front right and rear left  
GRILL  
3.8 kW  
2.7 kW  
2.0 kW  
150  
120  
100  
MAIN OVEN  
TOP OVEN  
29  
Installation Instructions  
SPACE FOR FIXING  
The cooker can be close fitted below hotplate level. This requires a minimum  
distance of 600mm between cupboard units of hotplate height.  
When installing next to a tall cupboard, partition or wall, for a minimum distance of  
400mm above hotplate level, allow a side clearance of at least 65mm.  
The diagram below illustrates the minimum clearance between the cooker and adjacent  
walls, cupboards etc.  
The wall behind the cooker between the hotplate and 450mm above, and the width of  
the cooker, must be a non-combustible material such as ceramic wall tiles.  
If the cooker is to be fitted close to a corner on the left hand side, ensure that there is a  
clearance of at least 50mm to allow the main oven door to open fully for when removing  
oven shelves.  
65 mm Min  
600mm min  
COOKER HOODS  
If a cooker hood is to be installed, refer to the cooker hood manufacturers’ instructions  
regarding fixing height.  
30  
Installation Instructions  
UNPACKING THE COOKER  
Unpack the components from inside the grill and oven.  
Check that the following parts are present:  
Grill pan and grid  
Pan supports (2)  
Main oven shelves (2)  
Top oven/grill shelf heat shield (Models KD643G and KD641G)  
Top oven/grill shelf (1) (Models KD643G and KD641G)  
Aluminium burner bodies (4)  
Enamelled burner caps (4) Literature  
LEVELLING  
Two rear wheels and two front feet are fitted which can be adjusted up or down to set the  
height (900mm - 915mm) and level the cooker.  
1.  
2.  
The rear wheels can be raised or lowered from the BACK of the cooker by adjusting  
the levelling screws ‘A’ in the plinth.  
The front feet can be simply screwed in or out to lower or raise the front of the  
cooker.  
CAUTION: Some soft floor coverings may get damaged if the cooker is not moved carefully.  
VIEWED FROM THE REAR  
STABILITY BRACKET  
The back of the cooker has a slot for engagement of a stability bracket, which can be  
obtained, as an extra, from your cooker supplier.  
REAR OF  
COOKER  
125mm  
STABILITY  
BRACKET  
POSITION  
SLOT FOR STABILITY BRACKET  
31  
Installation Instructions  
CONNECTING TO GAS SUPPLY  
The cooker is designed to match the depth of standard 600mm worktops. An adaptor  
backplate should, therefore, be fitted within the shaded area shown to allow the  
cooker to be pushed fully to the wall.  
220mm  
70mm  
GAS  
BACKPLATE  
POSITION  
40mm  
635mm  
30mm  
450mm  
Connection to the cooker should be made with an approved appliance flexible  
connection to BS 669. A length of 0.9 to 1.25m is recommended. The length of hose  
chosen should be such that when the cooker is in situ, the hose does not touch the  
floor.  
The temperature rise of areas at the rear of the cooker that are likely to come in  
contact with the flexible hose do not exceed 70˚C.  
32  
Installation Instructions - Electrical Connection  
WARNING – THIS APPLIANCE MUST BE EARTHED.  
CONNECT TO A 230-240V A.C. SUPPLY ONLY.  
Connection to the electricity supply should be made via a properly earthed, readily accessible  
wall socket which is adjacent to but not directly above, and not more than 1.25m away from the  
appliance and capable of electrical isolation.  
The mains lead should be routed such that it cannot touch hot parts of the cooker i.e. the back  
panel above a height of 650mm from the floor.  
Should this plug not fit the socket outlet in your home it should be cut off and replaced with a  
suitable plug as outlined below.  
NOTE: The removed plug cannot be used for any other appliance and should therefore be  
properly disposed of and not left where children might find it and plug it into a supply socket –  
with the obvious consequent danger.  
IF THE FITTED PLUG IS REMOVED  
The flexible mains lead must be correctly connected as below to a three pin plug of not less  
than 13 amp capacity. If a B.S. 1363 fused plug is used, it must be fitted with a 3 amp fuse which  
is approved to B.S. 1362.  
Green &  
Yellow to  
IMPORTANT: The wires in the mains lead fitted to this  
Earth  
appliance are coloured in  
accordance with the following code:  
Brown to  
Live  
Blue to  
Neutral  
GREEN AND YELLOW – EARTH  
BLUE  
BROWN  
– NEUTRAL  
– LIVE  
3 Amp  
Fuse  
Cord Clamp  
As the colours of the wires in the mains lead of this appliance may not correspond with the  
coloured markings identifying the terminals in your plug, proceed as follows:– The wire which is  
coloured green and yellow must be connected to the terminal in the plug which is marked with  
the letter E or by the earth symbol  
or coloured green or green and yellow. The wire which is  
coloured blue must be connected to the terminal which is marked with the N or coloured black.  
The wire which is coloured brown must be connected to the terminal which is marked with the  
letter L or coloured red. When wiring the plug, ensure that all strands of wire are securely  
retained in each terminal. Do not forget to tighten the mains lead clamp on the plug. As the  
appliance must be earthed, do not use 2-pin sockets outlets, if you are in doubt, consult a  
qualified electrician.  
Should the mains lead ever require replacement, it is essential that this operation be carried out  
by a qualified electrician and should only be replaced with a flexible cord of the same size i.e.  
0.75mm2 cross sectional area and temperature rating of 85˚C e.g. heat resisting PVC, available  
from our parts department (see Back Cover).  
IF A MOULDED PLUG IS FITTED  
In the event of replacing a fuse in the plug supplied a 3 amp ASTA approved fuse to BS1362  
must be fitted.  
NOTE: The fuse cover must be refitted when changing the fuse. In the event of losing the fuse  
cover the plug must not be used until a replacement fuse cover has been obtained and fitted. A  
new fuse cover can be obtained from your local Electricity Board. The colour of the correct  
replacement fuse cover is that of the coloured marks or inserts in the base of the plug.  
Make sure that the cable does not become trapped when pushing the cooker into position.  
33  
Installation Instructions  
INSTALLATION AND OPERATIONAL CHECKS  
After installation, check for gas soundness. The supply pressure can be checked at the  
grill injector. Access to the injector is by first removing the baffle at the front of the grill  
fastened by two screws. Then remove the fastening screw on the right hand side of the  
burner and slide the burner off the injector. Ensure that the grill burner is correctly  
located under the fixing screw on reassembly.  
Fit the hotplate burner bodies and caps, pan supports and shelf shield(s). Referring to  
the instructions for use where necessary,  
1. Check that the hotplate and grill burners ignite correctly and burn with a  
steady flame. Check for a steady flame on the low setting.  
2. Check that with the main oven set to mark 9, the burner ignites at low rate,  
and then increases to full rate within 60 seconds. Leave the oven full on with  
the door closed for 10 minutes, and check that when the control is turned to  
the ‘Slow Cook’ setting that the flame reduces.  
3. Check that with the top oven set to mark 8, the burner ignites at low rate,  
and then increases to full rate within 60 seconds. Leave the oven full on with  
the door closed for 10 minutes, and check that when the control is turned to  
mark 1 that the flame reduces.  
4. Check the operation of the oven timer and oven light(s).  
Instruct the user on operation of the cooker.  
NOTE - Models KD643G and KD641G only: It is normal for a slight resistance to be  
felt when turning the Top Oven/Grill control to the oven settings, as the control  
operates a flap at the rear of the cooker.  
34  
If It Still Won’t Work...  
Contact the Service Office (UK: 08709 066 066)  
If something is still wrong with your appliance after you have been through the  
‘Something Wrong’ list:  
1. Switch off and unplug the appliance from the mains.  
2. Call your nearest Service Office or local importer.  
When you contact us we will want to know the following:  
1. Your name, address and postcode.  
2. Your telephone number.  
3. Clear and concise details of the fault.  
4. The Model number and the Serial number of your appliance.  
5. The date of purchase (please keep the receipt as evidence will be required when  
an engineer calls) enter the date here:  
.............................................................................  
Please make sure you have all these details ready when you call.  
Spare Parts  
Please remember your new appliance is a complex piece of equipment.  
‘DIY’ repairs or unqualified and untrained service people may put you in danger, could  
damage the appliance and might mean you lose cover under the Parts Guarantee.  
If you do experience a problem with the appliance don’t take risks, call in our Service  
Engineer. Our Parts are designed exclusively to fit your appliance. Do not use them for  
any other purpose as you may create a safety hazard.  
Disposal of your product  
To minimise the risk of injury to children please dispose of your product carefully and  
safely. Remove all doors and lids. Remove the mains cable (where fitted) by cutting off  
flush with the appliance and always ensure that no plug is left in a condition where it  
could be connected to the electricity supply.  
To help the environment, Local Authority instructions should be followed for the  
disposal of your product.  
Disposal of old electrical appliances  
The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment  
(WEEE), requires that old household electrical appliances must not be disposed of in the  
normal unsorted municipal waste stream. Old appliances must be collected separately in  
order to optimise the recovery and recycling of the materials they contain and reduce  
the impact on human health and the environment.  
The crossed out “wheeled bin” symbol on the product reminds you of your obligation,  
that when you dispose of the appliance it must be separately collected.  
Consumers should contact their local authority or retailer for information concerning the  
correct disposal of their old appliance.  
35  
Key Contacts  
After Sales Service  
Over 1100 trained specialists, directly employed by us, ensure that you can have  
complete confidence in both the appliances and services we offer.  
Repair Service and Information Help Desk  
UK: 08709 066 066  
Monday to Friday, 8am to 7.30pm  
Saturday, 8.30am to 5.30pm  
Sunday, 9.30am to 3.30pm  
Republic of Ireland: 1850 302 200  
Note: Our operators will require the following information:  
Model number  
Serial number  
Extended Warranties  
UK: 08709 088 088  
Monday to Sunday, 8am to 8pm  
Republic of Ireland: 1850 502 200  
Genuine Parts and Accessories  
UK: 08709 077 077  
Monday to Friday, 8.30am to 5pm  
Saturday, 8.30am to 12noon  
Republic of Ireland: (01) 842 6836  
Indesit Company UK Limited, Morley Way, Peterborough, PE2 9JB  
.
PRINTED BY SIMLEX FOUR ASHES, WOLVERHAMPTON.  
07/2005 195045065.02  

IBM THINKCENTRE 8142 User Manual
JVC AV 21VT31 User Manual
Kentrox AI296 User Manual
MSi MSI Fuzzy Mainboard GME965 User Manual
Panasonic CT G2178 User Manual
Philips 25ML8966 User Manual
Philips 25PT900B User Manual
Philips 36PT 71B User Manual
Philips ID5551B User Manual
Philips MCD196 User Manual