Colour Plasma Display Monitor
USER'S MANUAL
MANUEL UTILISATEUR
BEDIENUNGSANLEITUNG
Model PW1
32PD5000
42PD5000
42PMA500
System Name
32PD5000
32PD5100
32PD5200
42PD5000
42PD5100
42PD5200
READ THE INSTRUCTIONS INSIDE CAREFULLY.
KEEP THIS USER'S MANUAL FOR FUTURE REFERENCE.
For future reference, record the serial number of your monitor.
SERIAL NO.
The serial number is located on the rear of the monitor.
This monitor is ENERGY STAR® compliant when used with a computer equipped with
VESA DPMS.
The ENERGY STAR® emblem does not represent EPA endorsement of any product or
service.
As an ENERGY STAR® Partner, Hitachi,Ltd. has determined that this product meets
the ENERGY STAR® guidelines for energy efficiency.
USER'S MANUAL
Thank you very much for purchasing the HITACHI Plasma Display
Monitor.
Before using your monitor, please carefully read the "SAFETY
INSTRUCTIONS" and this "USER'S MANUAL" so you will know how to
operate the monitor properly. Keep this manual in a safe place. You
will find it useful in the future.
Notes on lnstallation Work:
This product is marketed assuming that it is installed by qualifed
personnel with enough skill and competence. Always have an
installation specialist or your dealer install and set up the product.
HITACHI cannot assume liabilities for damage caused by mistake
in installation or mounting, misuse, modification or a natural
disaster.
Note for Dealers:
After installation, be sure to deliver this manual to the customer
and explain to the customer how to handle the product.
1
Important
FEATURES
Please read this User's Manual thoroughly, especially the Safety
Instructions on Page 4 to 7. Mis-use may cause damage to your
plasma monitor, which could shorten its lifespan, or cause injury to
yourself. Should you encounter any difficulty in the set-up or
operation of your monitor, firstly refer to the Troubleshooting guide at
the rear of this manual.
In the unlikely event of a problem occurring with your plasma monitor,
switch off at the mains sockets, pull out the plugs, and contact your
dealer immediately.
Large-screen, high-definition plasma display
panel
The 42-inch colour plasma display panel, with a resolution of 1024
(H) x 1024(V) pixels, and the 32-inch colour plasma display panel
with a resolution of 852(H) X 1024(V) pixels, creates a high-definition,
large-screen (aspect ratio : 16:9) and low-profile flat display. Free
from electromagnetic interferences from geomagnetic sources and
ambient power lines, the panel produces high-quality display images
free from colour misconvergence and display distortion.
CAUTION
Under no circumstances remove the rear cover of your plasma
monitor.
Never guess or take any chances with electrical equipment of any
kind - it is better to be safe than sorry!
High Performance Digital Processor
A wide range of personal computer signals can be handled, from 640
x 400, 640 x 480 VGA to 1600 x 1200 UXGA.
Easy-to-use remote control and on screen
Software Notice
It is prohibited for the end user of this product to copy, reverse
engineer or reverse compile the software included therein, save to
the extent permitted by law.
display system
The remote control included eases the work of setting display controls.
Further, the on-screen display system, displays the status of signal
reception and display control settings in an easy-to-view fashion.
Power saving system
Plasma Monitor
The International ENERGY STAR® power saver feature saves power
consumption automatically when input signals are not available.
When connected to a VESA DPMS-compliant PC, the monitor cuts its
power consumption while it is idle.
After the plasma monitor has been on for any length of time, you will
notice that the screen becomes warm. Please note that this is normal.
Sometimes the screen might have some tiny bright or dark spots.
Please note that this is normal.
TruBass
TruBass, SRS and (O) symbol are trademarks of SRS Labs,Inc.
TruBass technology is incorporated under license from SRS Labs, Inc.
CAUTION
To prevent scratches or damages to the plasma screen, do not
knock or rub the surface with sharp or hard objects. Clean the screen
with a soft cloth moistened with warm water and dry with a soft cloth.
A mild soap may be used if the screen is extremely dirty. Do not use
harsh or abrasive cleaners!
About the Optional Video Unit
The following functions can be obtained by connecting the optional video unit.
(1) A composite/S terminal and two component terminals have been
added. A composite video output terminal is also provided as a
monitoring output.
(2) A wide range of devices other than personal computers can also
be connected.
(3) A component input is possible to switch to RGB signals from the
Menu screen.
(4) A SCART terminal is also provided for the signal of the European
standard. It operates as composite/S/RGB input terminal, or video
output terminal.
CAUTION
Use a soft cloth to clean the cabinet and control panel of the monitor.
When excessively soiled dilute a neutral detergent in water, wet and
wring out the soft cloth and afterward wipe with a dry soft cloth.
Never use acid/alkaline detergent, alcoholic detergent, abrasive
cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc.
especially because they would cause discoloration, scratches or
cracks.
Options
Ask your local retail dealer for further details.
1. Desktop stand:
• CMPAD23 (for 32”)
• CMPAD25 (for 42”)
2. Plasma monitor speaker:
• CMPAS03 (for 32”) bass reflex speaker unit with 16x4.5cm
cone type speaker (colour: dark gray)
• CMPAS03S (for 32”) same type to CMPAS03 (colour: light gray)
• CMPAS14 (for 42”) 2 way speaker unit with one 2.5cm dome
type tweeter and two 8cm round type
woofers (colour: dark gray)
• CMPAS14S (for 42”) same type to CMPAS14 (colour: light gray)
3. Video unit: CMPAVW1
An expansion unit for viewing video with this device.
2
CONTENTS
FEATURES....................................................2
SAFETY INSTRUCTIONS..............................4
COMPONENT NAMES ..................................8
Main Unit..............................................................................8
Remote control ....................................................................9
Loading Batteries ..............................................................9
Handling the Remote Control ............................................9
INSTALLATION INSTRUCTIONS ................10
Installation..........................................................................10
Anti-tumble measures........................................................10
Connecting to a PC ..........................................................11
Mounting the Speaker Unit ..............................................12
Power Cord Connection ....................................................12
OPERATING INSTRUCTIONS ....................13
Turning Power On and Off ................................................13
Input Switching..................................................................14
Volume Adjustment............................................................14
Audio Mute ........................................................................14
Size Switching ..................................................................15
Input Signal Screen Display ..............................................15
Automatic Adjustment of Screen Position and the Clock..16
Independent Operation of Multiple Monitors ....................16
Using the Menu Screen ....................................................16
PICTURE MENU ................................................................17
AUDIO MENU....................................................................18
TIMER MENU ....................................................................18
FUNCTION MENU ............................................................19
SETUP MENU ....................................................................20
LANGUAGE MENU............................................................21
OTHER FEATURES ....................................21
Automatic Store ................................................................21
Signal Check ....................................................................22
Power Save Mode..............................................................22
IMAGE RETENTION OF PLASMA DISPLAY ......23
NOTES ........................................................23
TROUBLESHOOTING..................................24
Symptoms That Seemingly Appear to be Failures ............24
Actions to Correct Abnormal Displays ..............................26
PRODUCT SPECIFICATIONS ......................27
Signal Input........................................................................27
Recommended Signal List ................................................28
SUPPLEMENT ............................................30
Optional Video Unit Function ............................................31
Optional Tuner Unit Function ............................................43
Notes about This Manual
• The information in this manual is subject to change without notice.
• While meticulous care has been taken in the preparation of this manual, you are requested to notify your dealer or us should you have any
comments, views or questions about our product.
• Fully understand the prerequisites to using the product, such as hardware and software specifications and constraints, in using the
product. We are not held liable for damages caused by improper handling of the product.
• Reproduction of this manual in whole or in part without our prior written permission is prohibited.
• The product names mentioned in this manual may be trademarks or registered trademarks of their respective owners.
3
SAFETY INSTRUCTIONS
This Plasma monitor has been designed and manufactured to meet international safety standards, but like any electrical equipment, care must
be taken if you are to obtain the best results and safety is to be assured.
Before using this product, please read and understand the Safety Instructions thoroughly to ensure correct usage, and follow all the instructions.
About the Symbols
Various symbols are used in this manual, the user’s manual and on the product itself to ensure correct usage, to prevent danger to the user and
others, and to prevent property damage. The meanings of these symbols are described below. It is important that you read these descriptions
thoroughly and fully understand the contents.
This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to
incorrect handling.
WARNING
This symbol indicates information that, if ignored, could result possibly in personal injury or physical damage due
to incorrect handling.
CAUTION
Typical Symbols
This symbol indicates an additional warning (including cautions). An illustration is provided to clarify the contents.
This symbol indicates a prohibited action. The contents will be clearly indicated in an illustration or nearby (the symbol to the left
indicates that disassembly is prohibited).
This symbol indicates a compulsory action. The contents will be clearly indicated in an illustration or nearby (the symbol to the left
indicates that the power plug should be disconnected from the power outlet).
WARNING
Never use the monitor if a problem should occur.
Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing, elements, cables,
penetration of liquids or foreign matter, etc. can cause a fire or electrical shock.
In such case, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure
that the smoke or odor has stopped, contact your dealer. Never attempt to make repairs yourself because this could be
dangerous.
Disconnect the
plug from the
power outlet.
Do not insert liquids or foreign objects.
Penetration of liquids or foreign objects could result in fire or electrical shock. Use special caution in households where children
are present.
If liquids or foreign objects should enter the projector, immediately turn off the power switch, disconnect the power plug from the
power outlet and contact your dealer.
• Do not place the monitor in a bathroom.
• Do not expose the monitor to rain or moisture.
• Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc on or around the monitor.
• Do not place metals, combustibles, etc on or around the monitor.
Never disassemble or modify the monitor.
The monitor contains high voltage components. Modification could result in fire or electrical shock.
• Never remove any fixed cover.
Do not
disassemble.
Do not give the monitor any shock or impact.
If the monitor should be shocked and/or broken, it could result in an injury, and continued use could result in fire or electrical shock.
If the glass panel is broken or damaged, immediately turn off the power switch, disconnect the power plug from the power outlet
and contact your dealer.
Do not place the monitor on an unstable surface.
If the monitor should be dropped and/or broken, it could result in an injury, and continued use could result in fire or electrical shock.
• Do not place the monitor on an unstable, slant or vibrant surface such as a wobbly or inclined stand.
Do not obstruct the ventilation of the monitor.
If the ventilation is obstructed during the operation of the monitor or just after switching off the power, it could result in damage
and shorten the lifespan of your monitor due to overheating. Make sure there is ample ventilation.
• Keep a space of 100mm (10cm) or more between the sides, rear and top of the monitor and other objects such as walls.
• Do not place anything around ventilation openings of the monitor.
• Never block ventilation openings.
• Do not put the plasma screen side up.
• Do not cover the monitor with a tablecloth, etc.
• Do not place the monitor on a carpet or bedding, or near a curtain.
Use only the correct power outlet.
Incorrect power supply could result in fire or electrical shock. Use only the correct power outlet depending on the indication on the
monitor and the safety standard.
• The enclosed power cord must be used depending on the power outlet to be used.
4
WARNING
Be cautious of the power cord connection.
Incorrect connection of the power cord could result in fire or electrical shock.
• Do not touch the power cord with a wet hand.
•
Check that the connecting portion of the power cord is clean (with no dust), before using. Use a soft and dry cloth to clean the power plug.
• Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure.
• Do not cut off the fitted power plug, the removal of which could lead to impaired performance. If you wish to extend the lead,
obtain an appropriate extension lead or consult your dealer.
• Should you require replacing the fuse in the molded plug with a new fuse, then please replace with new one of the same value,
type and approval as the original. Ensure the fuse cover is returned to its original position.
Be sure to keep safety ground connection.
Connect the ground terminal of AC inlet of this monitor with the ground terminal provided at the power outlet using the enclosed
power cord. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet.
Surely connect
the ground wire.
Be careful in handling the power cord and external connection cables.
If you keep using a damaged the power cord or cables, it can cause a fire or electrical shock. Do not apply too much heat,
pressure or tension to the power cord and cables.
If the power cord or cables are damaged (exposed or broken core wires, etc.), contact your dealer.
• Do not place the monitor or heavy objects on the power cord and cables. Also, do not place a spread, cover, etc, over them
because this could result in the inadvertent placing of heavy objects on the concealed power cord or cables.
• Do not pull the power cord and cables. When connecting and disconnecting the power cord or cables, do it with your hand
holding the plug or connector.
• Do not place the cord near the heater.
• Do not touch the power plug just after disconnecting it from the power outlet to prevent electric shock.
• Do not touch the power plug when lightening is close to you.
• Avoid coiling the power cord and bending it sharply.
• Protect the power cord from being walked on, pinched particularly at plugs, conveniences receptacles, and the point where they
exit from the apparatus.
• Do not modify the power cord.
Be careful in handling the battery of the remote control.
Incorrect handling of the battery could result in fire or personal injury. The battery may explode if not handled properly.
• Keep the battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.
• Do not allow the battery to be exposed to fire or water.
• Avoid fire or high-temperature environment.
• Do not hold the battery with metallic tweezers.
• Keep the battery in a dark, cool and dry place.
• Do not short circuit the battery.
• Do not recharge, disassemble or solder the battery.
• Do not physically impact the battery.
• Use only the battery specified in the manual of this monitor.
• Make sure the plus and minus terminals are correctly aligned when loading the battery.
• If you observe a leakage of the battery, wipe out the liquid and then replace the battery. If the liquid adheres your body or
clothes, rinse well with water.
• Obey the local laws on disposing the battery.
• FOR THE CUSTOMERS IN THE U.K.
THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K. PLEASE REFER TO THE
NOTES ON THIS PAGE.
IMPORTANT FOR UNITED KINGDOM
WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS
The mains lead on this equipment is supplied with a molded plug incorporating a fuse, the value of which is indicated on the pin face of the plug.
Should the fuse need to be replaced, an ASTA or BSI approved BS 1362 fuse must be used of the same rating. If the fuse cover is detachable
never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of
the plug. Fuse covers are available from your dealer.
DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to
reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.
Should it be necessary to change the mains plugs, this must be carried out by a competent person, preferably a qualified electrician.
If there is no alternative to cutting off the mains plug, ensure that you dispose of it immediately, having first removed the fuse, to avoid a possible
shock hazard by inadvertent connection to the mains supply.
WARNING: THIS EQUIPMENT MUST BE EARTHED
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code :
Green and Yellow = Earth, Blue = Neutral, Brown = Live.
As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the earth
symbol
or coloured GREEN or GREEN and YELLOW.
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN
must be connected to the terminal marked with the letter L or coloured BROWN or RED.
Green & Yellow
to Earth
Brown to Live
Fuse
Blue to Neutral
Cord Clamp
5
SAFETY INSTRUCTIONS(continued)
CAUTION
Be careful in moving the monitor.
Neglect could result in an injury or damage.
• Do not move the monitor during use. Before moving, disconnect the power plug and all external connections.
• You are advised to move the monitor with two persons.
• Avoid any impact or shock to the monitor; particularly take care of glass screen.
Do not put anything on top of the monitor.
Placing anything on the monitor could result in loss of balance or falling, and cause an injury or damage. Use special caution in
households where children are present.
Avoid a humid or dusty place.
Placing the monitor in a smoke, a highly humid, dusty place, oily soot or corrosive gas could result in fire or electrical shock.
• Do not place near the kitchen, a humidifier or other place where there is oil, smoke or humidity.
Avoid a high temperature environment.
The heat could have adverse influence on the monitor and other parts, and could result in transformation, melting or fire.
• Do not place the monitor, the remote control and other parts in direct sunlight or near a hot object such as heater, etc.
• Do not put the monitor in a place where the temperature is widely changing.
Remove the power cord for complete separation.
• For safety purposes, disconnect the power cord if the monitor is not to be used for prolonged periods of time.
• Before cleaning, turn off and unplug the monitor. Neglect could result in fire or electrical shock.
Disconnect the
plug from the
power outlet.
PRECAUTIONS
• Installation environment
Do not obstruct a ventilation hole.
Do not put the monitor on carpet or blanket, or near a curtain which has a possibility of obstructing a ventilation hole of the monitor.
Do not put the monitor in the following places.
• Hot places such as near heater, place exposed to the direct rays of the sun.
• A place where the temperature is widely changing.
• Places with soot, dust or high humidity.
• Poor air ventilation place.
• Place near fire.
• A wet place such as bathroom, or shower room.
• Place where you can trip over it.
• Always vibrating or strongly vibrating places.
• Distorted or unstable places.
• How to view the monitor
If you use the monitor in too dark a room, your eyes may become tired.
Please use it in a reasonably bright room.
Avoid direct rays of the sun to the screen in order to prevent eye fatigue.
Your eyes will get fatigued after viewing the monitor for long period of time.
Relax your eyes by viewing away from the monitor from time to time.
Please watch the monitor in downward direction.
• Note on image retention
The plasma monitor illuminates phosphor to display images. The phosphor has a finite illumination life. After extended periods of illumination, the
brightness of the phosphor will be degraded to such extent that stationary images would burn-in that part of the screen as grayed-out images.
Tips to prevent such image retention are:
- Do not display images having sharp brightness differences or high-contrast images, such as monochrome characters and graphic patterns,
for long.
- Do not leave stationary images appearing for long, but try to refresh them at appropriate intervals of time, or try to move them using screen
saver function.
- Turn down the contrast and brightness controls.
• How to clean the plasma screen panel of the monitor
Before cleaning the monitor, turn off the monitor and disconnect the power plug from the power outlet.
To prevent scratching or damaging the plasma screen face, do not knock or rub the surface with sharp or hard objects. Clean the screen with
a soft cloth moistened with warm water and dry with a soft cloth. If it is not enough, then use a cloth with mild detergent. Do not use harsh or
abrasive cleaners.
• How to clean the cabinet of the monitor
Use a soft cloth to clean the cabinet and control panel of the monitor. When excessively soiled dilute a neutral detergent in water, wet and
wring out the soft cloth and afterward wipe with a dry soft cloth.
Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc. especially
because they would cause discoloration, scratches or cracks.
6
• Prevention of an obstacle to Radio receivers
This monitor has been designed pursuant to the international EMI standards. This is to prevent a problem to Radio receivers.
- Keep the monitor away from Radio.
- Adjust Radio antennas in order for the monitor not to receive interference.
- The antenna cable of Radio should be kept away from the monitor.
- Use a coaxial cable for antenna.
You can check if this monitor influences Radio receivers by turning off all other equipment other than the monitor.
If you find a problem receiving Radio when using the monitor, check the instructions mentioned above.
• Precautions for the cable connection
- Do ensure that all connections, (including the power plug, extension leads and interconnections between the pieces of equipment), are
properly made and in accordance with the manufacturers instructions. Switch off and withdraw the power plug before making or changing
connections.
- Confirm the connector is fixed tightly when the signal cable is connected.
Also confirm the screws on the connector are tightened.
- Plug the power cord of the monitor into a different socket from that for other equipment, such as Radio etc..
- Use a plug with ground terminal and make sure that it connects to the ground.
• Precaution during transportation
Please pay attention when you transport this monitor because it is heavy.
Furthermore, use the original carton box and its packaging materials when the monitor is transported.
Failure to transport the monitor in any carton except the original carton may result in damage to the monitor.
Save the original carton box and all packing material.
Do not physically impact the remote control.
A physical impact could cause damage or malfunction of the remote control.
• Take care not to drop the remote control.
• Do not place heavy objects on the remote control.
Avoid strong rays.
Any strong rays (such as direct sun rays or room lighting) onto the remote control sensors could invalidate the remote control.
Avoid radio interference.
Any interfering radiation could cause distorted images or noises.
• Avoid radio generator such as a mobile telephone, transceiver, etc. around the monitor.
Set the sound volume at a suitable level.
It is better to keep the volume level low and close the windows at night to protect the neighborhood environment.
• Precautions for the installation
- Do not use makeshift stands and NEVER fix legs with wood screws - to ensure complete safety, always fit the manufacturers approved stand
or legs with the fixings provided according to the instructions.
- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.
- This product is designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to the
front, or top, of the cabinet that could cause the product to overturn resulting in product damage and/or personal injury.
- Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.
- Only use the attachments/accessories specified by the manufacturer.
- Consult your dealer if you are in any doubt about installation, operation or safety of your equipment.
• Other precautions
- Do not leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a
stand-by mode. Switch off using the switch on the equipment and show your family how to do this. Make special arrangements for infirm or
handicapped people.
- Disposal of this product may require specific instructions pertaining to your resident region.
- Never guess or take any chances with electrical equipment of any kind - it is better to be safe than sorry!
7
COMPONENT NAMES
Main Unit
Front
Cabinet
(front frame)
Panel
Control panel
• Adjustment buttons are located
on the bottom.
• The back cover is provided with
indications to distinguish the
adjustment buttons.
Remote-control
receiver
9
Indicating lamp
13
• The main power switch is located at the back, on the
lower surface.
MENU button
16
Main power switch
13
▼
▼
INPUT SELECT button
(OK button)
14
VOLUME
UP/DOWN
(42")
15
RECALL button
14
buttons
(
SELECT button)
(
ADJUST
buttons)
15
SIZE button
(
SELECT button)
SUB-POWER button
13
• ( ) indicates the function while the MENU is displayed on the screen.
(32")
Caution when moving the main unit
• As this product is heavy, whenever it is moved, two
people are required to transport it safely.
Rear
• Whenever the unit is moved it should be lifted forwards
using the two handgrips at the back, and the unit should
then be held at the base on both sides for stability.
Handgrips
Handgrips
Handgrips
External
speaker
terminals
External
speaker
terminals
11
11
External device connection terminals
RGB input terminals
11
8
Remote control
POWER OFF button
13
13
14
13
14
POWER ON/OFF button
POWER ON button
MUTE button
VOLUME UP/DOWN buttons
VOL
VOL
RGB/VIDEO buttons
14
RGB 1
AV1
RGB 2
AV2
MUTE
AV3
15
15
SIZE button
PinP button
34
16
AV4
AUTO button
AUTO
MENU
PinP
SIZE
RECALL
RECALL button
MENU button
OK button
16
16
16
16
16
RETURN button
OK
SELECT/ADJUST buttons
ID SET button
ID
ID SET
ID button
16
Loading Batteries
Handling the Remote Control
1. Open the battery cover.
• Slide back and remove the battery
cover in the direction of the arrow.
Use the remote control within about 5 m from front of the unit’s
remote-control sensor and within 30 degrees on both sides.
2. Load batteries.
• Load two Size AA batteries included observing the correct
polarities.
With in 30
With in 30
degrees
degrees
About 3m
About 3m
About 5m
VOL
3. Close the battery cover.
• Replace the battery cover in the direction of the arrow and snap
it back into place.
RGB
1
RGB
2
MUTE
VOL
AV1
AV2
AV3
AV4
AUTO
MENU
PinP
SIZE
RECALL
OK
ID
ID SET
ATTENTION
• Do not drop or impact the remote control.
CAUTION
• Do not use new and old batteries together. The batteries could
explode or leak, resulting in fires, physical injury, or stains.
• When loading batteries, observe their correct polarities as
marked on the product. If loaded in the wrong direction, the
batteries could explode or leak, resulting in fires, physical injury,
or stains.
• Do not splash the remote control with water or put it on a wet
object to avoid possible failures.
• Before leaving the remote control out of use for an extended
period of time, remove the batteries from it.
• If the remote control begins to lack responsiveness, replace the
batteries.
• Strong light such as direct sunlight impinging on the
photoreceptor of the remote control can cause operational
failure. Position this unit to avoid direct contact with such light.
9
INSTALLATION INSTRUCTIONS
Installation
• If you have purchased the model without the stand attached:
When installing the monitor, use the optional Desk-top Stand (CMPAD23/25).
The Desk-top Stand has been used for the illustrations in this manual.
WARNING
Use one of the special mount units to install this product. A mount of insufficient strength or inadequate design can cause overturning or
dropping and result in fire, electrical shock or injury. Please note that our company assumes absolutely no responsibility for personal injuries
or property damage caused by use of other mount units or improper installation.
10cm (4 inches) or more*
CAUTION
• Installation of the wall mount unit and ceiling mount unit can be dangerous, so do not attempt this work
yourself. Ask your dealer to provide the name of a qualified installer.
Clamp
• In order to prevent an internal temperature increase, maintain a space of 10cm (4 inches : For a desktop set-
up) or more between the sides and other objects such as walls, etc., so that the ventilation holes are not
blocked.( )
✻
Cord
or
chain
Anti-tumble measures
CAUTION
Have this unit mounted in a stable place. Take measures to prevent it from tumbling down to avoid possible physical injury.
Securing to a wall or pillar
Using a commercially available cord, chain and clamp, secure the set to a firm wall or pillar.
cord or chain for 32"
Hook
Chain
cord or chain for 42"
Wall or Pillar
clamp for 32"
clamp for 42"
Securing desktop
1) Using wood screws (two), fasten the set to the clamping screw holes on the rear of the stand as shown.
2) Using commercially available wood screws, secure the set firmly in position.
Wood screw
Two places
10
4
7
Read SAFETY INSTRUCTIONS (
proceeding to these steps:
to
) carefully to ensure maximum safety before
• Choose an appropriate site and install the product on a level table where the stand is secure.
• Install the monitor to have ready access to a power socket available.
• Make sure that the power switch of this device is turned off.
Connecting to a PC
(1) Make sure that the display signal of the personal computer to be used is compatible with the specifications of this
device.
27
29
~
• See "Product Specifications" concerning the specifications of this device.
(2) Make sure that the power switch of the personal computer is turned off.
(3) Connect the signal input terminal (RGB 1 or RGB 2) on the rear panel of this device to the display signal output
terminal of the personal computer.
• Use a cable that fits the input terminal of this device and the output terminal of the personal computer.
• Depending on the type of personal computer being connected, the use of an optional conversion adapter or the adapter provided with
the personal computer may be necessary in some cases. For details, refer to the instruction manual of the personal computer or ask the
personal computer manufacturer or your local retail dealer.
Monitor rear panel
Speaker (R)
Speaker (L)
Power cable
connector
3.5mm
Stereo
mini jack
Power
cord
(DVI)
(D-sub)
To signal
output
terminal
To signal
output
terminal
To audio
output
terminal
11
INSTALLATION INSTRUCTIONS (continued)
Mounting the Speaker Unit
(option)
Refer to the instruction manual concerning mounting of the optional speaker unit.
Power Cord Connection
Connect the power cord, after completing all other connections.
①
➁
① Connect the power cord to this device.
➁ Connect the power cord plug to the power outlet.
(The type of plug is different from this drawing for some countries.)
CAUTION
• Use only the power cord provided.
• Do not use a power supply voltage other than that indicated (AC100-240V, 50/60Hz) as this may cause fire or electric shock.
12
OPERATING INSTRUCTIONS
Turning Power On and Off
• To turn the monitor power ON, press the main power
switch on the monitor main unit to ON, and then press
the SUB POWER button or the ON/OFF or ON button on
the remote control.
Indicating lamp
• To turn the monitor power OFF, press the SUB POWER
button or the ON/OFF or OFF button on the remote
control, and then press the main power switch on the
Main power switch
monitor main unit to OFF.
• During normal use, the main power switch is set in the ON
position, and the monitor can then be turned ON/OFF using the
SUB POWER button or the ON/OFF button on the remote control.
(42")
(32")
Indicating lamp
Indicating
Power status
Operating
lamp
When the main power switch is set
to OFF.
Off
Off
When the main power switch is
ON, and the OFF button on the
remote control or the SUB POWER
button on the underside of the
front of the frame is OFF.
Off
(standby)
Lights red
When the main power switch is
ON, and the ON button on the
remote control or the SUB POWER
button on the underside of the
front of the frame is ON.
Lights green
On
When the main power switch is
ON, and the ON button on the
remote control or the SUB POWER
button on the underside of the
front of the frame is ON.
Off
Lights orange
SUB-POWER button
(Power Save)
However, the state in POWER
SAVE mode
POWER OFF
button
When the indicating lamp lights in orange or the message “No Sync.
Signal”, “Power Save” or “Invalid Scan Freq.” appears on the
screen, there is something unusual about the status of reception.
See “Power Save Mode” or “Symptoms That Seemingly Appear to be
POWER ON/OFF
POWER ON
Failures.”
22
24
button
button
ATTENTION
VOL
• Avoid repeatedly turning the monitor on and off at short time
intervals. Failures might result from such operation.
• Turn off the main power switch before leaving the monitor out of
use for an extended period of time.
RGB 1
AV1
RGB 2
AV2
MUTE
AV3
VOL
AV4
• If a power failure occurs while the main unit is running, it would
be powered on upon recovery from the failure. Turn off the unit
main power switch before leaving the main unit.
AUTO
MENU
PinP
SIZE
RECALL
OK
ID
ID SET
13
OPERATING INSTRUCTIONS (continued)
Volume Adjustment
The volume can be adjusted by pressing the VOL+ and
▲
▼
VOL- buttons of the remote control (or the and
volume buttons of the monitor unit).
Volume setting value
▼
▼
Volume 15
VOLUME UP/DOWN
buttons
INPUT SELECT button
Adjustment status guide display
• When a button is pressed, the volume adjustment
status guide will be displayed.
MUTE button
RGB buttons
▲
• The volume will increase when the VOL+ (or ) button is
pressed while the guide is being displayed.
• The volume will decrease when the VOL- (or ) button is
▼
pressed while the guide is being displayed.
VOL
VOLUME
UP/DOWN buttons
RGB 1
AV1
RGB 2
AV2
MUTE
AV3
VOL
Audio Mute
AV4
AUTO
MENU
PinP
SIZE
RECALL
The audio volume can be temporarily mute by pressing
the MUTE button of the remote control.
OK
ID
ID SET
Volume setting value
Volume 15
Adjustment status guide display
(The display colour will change to magenta.)
Input Switching
• When a button is pressed, the volume adjustment
status guide (magenta) will be displayed.
• The volume setting can be lowered by pressing the VOL- button
while the audio is mute.
•
•
Input can be switched by pressing the RGB1, RGB2,
buttons of the remote control.
• The muting can be cancelled by pressing the VOL+ button or
MUTE button while the audio is mute.
Input can be switched in the sequence of RGB1
RGB2 by pressing the INPUT SELECT button of the
monitor.
➔
When the MUTE button of the remote control is pressed
again, the audio will be restored and the volume display
(green) will appear.
RGB1
RGB2
14
RGB 1
AV1
RGB 2
AV2
MUTE
AV3
VOL
AV4
AUTO
MENU
PinP
SIZE
RECALL
RECALL button
OK
SIZE button
ID
ID SET
RECALL button
SIZE button
Size Switching
Each time the SIZE button of the remote control or the monitor is pressed, the screen display area will change in
sequence and the status will be displayed at the bottom of the screen.
Normal
*
Full
Zoom1
Real
Zoom3
Zoom2
* Real mode gives the image of the same shape as it is displayed on a computer monitor.
This mode is only available for VGA (640 X 480) and WVGA (864 X 480).
Display area selection diagram (RGB input)
Resolution
Display
Full display
Full
Circular display
Zoom1
Normal
Real
Zoom2
Zoom3
640 X 480
(VGA)
800 X 600
(SVGA)
1024 X 768
(XGA)
1280 X 1024
(SXGA)
* VGA and W-VGA
only
1600 X 1200
(UXGA)
Processes such as compression (thinning) and expansion are performed for the above signal display. Because of this, there is a possibility that
flicker may become noticeable on Zoom (1 ~ 3) depending on the display contents. If this occurs, turning the Vertical Filter On
the flicker.
can reduce
20
Input Signal Screen Display
The input signal status can be displayed on the screen by pressing the RECALL button of the remote control or the monitor.
• The display will go out in approximately 6 seconds.
RGB
RGB2
RGB
H : 48.4kHz
V : 60.1 Hz
Input mode
Signal mode
Input horizontal frequency
Input vertical frequency
Off-timer
On-timer
-- -- Min.
-- -- : -- --
OFF
15
OPERATING INSTRUCTIONS (continued)
Using the Menu Screen
(On-screen display system)
VOL
VOL
RGB 1
AV1
RGB 2
AV2
MUTE
AV3
When the MENU button is pressed, the adjustment menu
screen will be displayed; from there, PC signal adjustment
and setting is possible by using the SELECT button,
ADJUST button and OK button.
AV4
RETURN buttons
AUTO
MENU
PinP
SIZE
RECALL
AUTO button
MENU button
• Refer to
settings.
-
concerning the adjustment items and the
21
17
SELECT/ADJUST
buttons
OK
Example: Selecting the Picture screen
ID
ID SET
OK button
ID button
1. Press the MENU button to display the Main Menu
ID SET button
screen.
Picture
Audio
MENU
Timer
Function
Setup
Language
Select
OK Set
Automatic Adjustment of
Screen Position and the Clock
2. Press the OK button to display the Picture Menu
Adjustment of the screen to a position suitable for the PC
signal and the clock adjustment can be performed
automatically by pressing the AUTO button of the remote
control.
screen. (Use the
other items.)
and
SELECT buttons to select
Picture
Contrast
Brightness
Colour
Hue
Picture Enhancement
Colour Temperature
Colour Temp.Adjust
Reset
:
:
:
:
:
:
+ 31
– 31
0
+ 31
Off
OK
CAUTION
Perform this adjustment for each input (RGB1 or RGB2) and for
each signal.
Normal
Reset
Exit
Select
Return
* Depending on the signal, satisfactory adjustment may not be
possible in some cases. In such case, adjust by referring to the
Setup Menu item.
3. Use the
be adjusted and then use the
and
SELECT buttons to select the item to
and ADJUST
buttons to adjust (example: Contrast).
Independent Operation of
Multiple Monitors (ID No)
Setting the ID No. of the remote control allows separate
control of up to a maximum of seven monitors.
Remote control ID No. 2 (initially ID no. 1) can be set by
pressing the ID SET button for 2 sec. or more while
holding down the ID button. The number will be
Contrast
Next / Prev
+ 31
Adjust
Return
incremented (2•••6
7
1
2) when this button pressed
➔ ➔ ➔
• Press the RETURN button to return to the previous screen.
• If there is no operation for a period of one minute, the
Adjustment Menu screen will be closed automatically.
continuously.
The remote control ID no. can be
checked by pressing the ID SET button
while holding down the ID button.
ID Number
Monitor
R/C
[ 1 ]
[ 1 ]
Monitor ID no.
Remote control ID no.
The ID remote control is operated by pressing the
various buttons while holding down the ID button;
Operation is possible only when the remote control and
monitor ID nos. are the same.
• The remote control can be operated normally by pressing the
various remote control buttons without holding down the ID button.
• Set the monitor using the ID No. of Function MENU.
19
16
PICTURE MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Picture
Contrast
Brightness
Colour
:
:
:
:
:
:
+ 31
– 31
0
+ 31
Off
OK
OK
MENU
Hue
Picture Enhancement
Colour Temperature
Colour Temp.Adjust
Reset
Normal
Reset
Contrast
+ 31
Select OK Set
Return
Next / Prev
Adjust
Return
Picture
Contrast
Brightness
Colour
Hue
Picture Enhancement
Colour Temperature
Colour Temp.Adjust
Reset
:
+ 31
– 31
0
+ 31
Off
OK
:
:
:
:
:
Normal
Colour Temperature
Next / Prev
Normal
Return
Reset
Select
Select OK Set
Return
Picture
Colour Temp. Adjust
Amplitude
Red
Picture
Contrast
Brightness
Colour
Hue
Picture Enhancement
Colour Temperature
Colour Temp.Adjust
Reset
On
:
+ 31
– 31
0
+ 31
Off
– 63
0
– 31
OK
:
:
:
:
:
Green
Blue
Cut Off
Red
Green
+ 31
0
+ 31
Normal
Blue
Reset
Reset
Reset
Return
Select
Set
Return
OK
Select
On/Off
Selected characters
Setup hint
Adjust for maximum visibility to suit the ambient brightness.
This can adjust further till [+40] by pressing and holding
cursor
button at [+31]. The color for [+32] to [+40] numbers will change from
white to magenta. This special mode is better for dark scenes.
For brighter scene some parts of the picture might not be clear. We
recommend to set at [+31].
Narrows the gap between
brightness and darkness.
Broadens the gap between
brightness and darkness.
Contrast
"Panel Life" in the Function Menu should be set to Normal when
Contrast setting is adjusted.
Adjust to taste.
Black is subdued for
increased overall darkness.
Black is set off for increased
overall brightness.
Brightness
Colour
Darkens colours.
Lightens colours.
Adjust to taste.
This is not available to adjust when receiving PAL/SECAM signal.
In this case the character will be grayed out.
Adjust for most realistic skin colour.
Enhances red and weakens
green.
Enhances green and weakens
red.
Hue
Off
Low
Middle
Warm
On
High
Sets the clarity of small details to the desired level.
Normally set to Normal.
Picture Enhancement
Cool
Normal
Black / White
Colour Temperature
Turn On when you wish to change colour temperature depending on
the user’s preference.
Off
Colour Temp. Adjustment
Brighter scene is decreased in Brighter scene is increased in
reddish colour. reddish colour.
Amplitude
Red
Brighter scene is decreased in Brighter scene is increased in
greenish colour. greenish colour.
Green
Blue
Brighter scene is decreased in Brighter scene is increased in
Adjust colour temperature depending on the user’s preference. These
settings are independently stored in each of the 4 Colour Temperature
modes.
bluish colour.
bluish colour.
Dark scene is decreased in
reddish colour.
Dark scene is increased in
reddish colour.
Cut Off
Red
Dark scene is decreased in
greenish colour.
Dark scene is increased in
greenish colour.
Green
Dark scene is decreased in
bluish colour.
Dark scene is increased in
bluish colour.
Blue
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
(off the function)
(waiting to reset)
Reset
17
OPERATING INSTRUCTIONS (continued)
AUDIO MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Audio
Audio Mode
Treble
Bass
Balance
SRS TruBass
Matrix Surround
Perfect Volume
Reset
:
:
:
:
:
:
:
Movie
+ 10
– 10
0 L
Middle
Off
OK
MENU
R
Off
Reset
Select
Set
Return
Selected characters
Setup hint
Movie: This selects the audio suitable for Movie.
Music: This selects the audio suitable for Music.
Speech: This selects the audio suitable for News, Talk show etc.
Favourite: This mode should be adjusted depending on user’s
preference.
Movie
Music
Speech
Favourite
Audio Mode
Suppresses treble.
Suppresses bass.
Enhances treble.
Enhances bass.
Adjust to taste.
Adjust to taste.
Adjust to taste.
Treble
Bass
Suppresses right-side sound. Suppresses left-side sound.
Balance
SRS TruBass takes advance of the ability of the human ear to be able
to distinguish between two different tones. By using this ability,
TruBass gives enhanced bass sound that otherwise would not be
heard. Adjust it depending on the user’s preference.
Off
Low
Middle
High
SRS TruBass
Off
On
On
This features the spacious sound effects of a stadium.
Matrix Surround
Perfect Volume
Reset
This will automatically adjust volume so each channel and input has
the same average volume level.
Off
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
(off the function)
(waiting to reset)
TIMER MENU
Picture
Audio
Timer
Function
Setup
Timer
Off Timer
On Timer
Select
:
:
30Min.
- - : - -
Return
OK
Adjust
MENU
Language
Select
OK Set
Selected characters
Setup hint
--Min.
30Min.
60Min.
90Min.
This function automatically sets the power to standby status when the
indicated time period has elapsed.
Off Timer
120Min.
This automatically sets the power from standby to ON when the
indicated time period has elapsed. The settable time is 00:00~11:59.
- - ( : - - )
hours
(- - : )- -
minutes
On Timer
Input the required time by
control.
SELECT buttons on the remote
18
FUNCTION MENU
Picture
Audio
Timer
Function
Setup
Language
Select
Function
Screen Saver
Screen Wipe
Black Side Panel
Video Power Save
Freeze Mode
Default Zoom
Reset
Off
On 60Min.
Off
Off
Split
Panoramic
Reset
Return
OK
MENU
OK Set
Select
Set
Function
Panel Life
Mode Display
ID Number
Inverse
Normal
Off
1
On 60Min.
Off
2.2
Standby White
Gamma
Reset
Select
Reset
Return
Set
Selected characters
Setup hint
This moves the picture around the screen in small amounts, at set
intervals, to reduce the panel image retention. This is where
stationary objects, such as screen logos, leave a slight image visible
after they should have disappeared.
Off
60Min.
5Min.
40Min.
10Min.
20Min.
Screen Saver
Screen Wipe
This is used to reduce the panel image retention that can occur with
stationary pictures by the white field signal. Select On (continuous
operation) or 60 Min. (time limit operation) and press the OK button.
Press the MENU or RETURN button on the remote control to return to
normal viewing.
On
60Min.
This turns the gray sidebars On/Off when watching normal mode
screen size area. It is always set to Off when the monitor powered
On. It is recommended to set to Off to reduce the panel image
retention.
Off
On
Black Side Panel
Optional (grayed out)
Video Power Save
Freeze Mode
Optional (grayed out)
Optional (grayed out)
Default Zoom
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
(off the function)
Normal
(waiting to reset)
Reset
This function is to suppress the contrast of the screen regardless of
the Contrast setting in the Picture Menu. By this control, power
consumption can be reduced or degradation of a panel can be
mitigated. The order of power consumption is Extend 2 < Extend 1 <
Normal.
Extend 1
Extend 2
Panel Life
If the Contrast setting is changed when this item is set to Extend 1 or
2, it will be changed to Normal automatically.
This can display the Input Signal Screen Display every time the input
mode and signal mode are changed.
Set to OFF if the Input Signal Screen Display is not needed when
switching signals.
Off
2
On
Mode Display
ID Number
Inverse
1
3
4
Assigns ID nos. to the monitors so that they can be controlled
individually (up to 7 monitors can be controlled).
7
6
5
This function can change each level of RGB signal invert to reduce
the panel image retention. When this function is required to use,
select On (continuous operation) or 60Min. (time limit operation) and
press the OK button. And press the Menu or Return button to exit.
On
60Min.
This function is also provided against the image retention. If time is
set for this item, the screen changes into the white pattern when the
monitor enters power save mode, and it will continue for the period of
setting time.
Off
15Min.
120Min.
30Min.
60Min.
Standby White
Gamma
2.2
2.8
Normally set to 2.2.
19
OPERATING INSTRUCTIONS (continued)
SETUP MENU
Picture
Audio
Timer
Function
Setup
Language
Select
Setup
Auto Adjust
Horizontal Position
Vertical Position
Horizontal Clock
Clock Phase
Reset
Adjust
0
+ 31
– 20
10
Reset
OK
OK
MENU
OK Set
Select
Return
Exit
Horizontal Position
Next / Prev
0
Adjust
Return
Setup
Auto Adjust
Adjust
0
+ 31
– 20
10
Reset
Exit
OK
Horizontal Position
Vertical Position
Horizontal Clock
Clock Phase
Reset
Select
Return
Clock Phase
Next / Prev
10
Adjust
Return
Setup
Input Level
Frequency Display
WVGA Type
Vertical Filter
Frequency Mode
RGB1
0.7V
Off
Off
On
Movie
DVI-PC
RGB
RGB2
Select
Set
Return
Selected characters
Setup hint
(Menu)
Adjust
Horizontal Position, Vertical Position, Horizontal Clock and Clock
Phase are adjusted automatically.
Pressing the OK button here,
Automatic regulation is started.
Auto Adjust*
Moves the horizontal position Moves the horizontal position
Adjust the left-side display position.
(This function is only for RGB2. It’s not available (grayed out) for
RGB1.)
to left.
to right.
Horizontal Position
Vertical Position
Moves down the vertical
position.
Moves up the vertical position.
Adjust the vertical display position.
(This function is only for RGB2. It’s not available (grayed out) for
RGB1.)
Reduces the dot clock
frequency (shrinks the right
side).
Increases the dot clock
frequency (expands the right
side).
Adjust for maximum character clarity.
(This function is only for RGB2. It’s not available (grayed out) for
RGB1.)
Horizontal Clock
Clock Phase
Slows the dot clock phase
(shifts slightly to left).
Advances the dot clock phase
(shifts slightly to right).
Adjust for clear character visibility.
(This function is only for RGB2. It’s not available (grayed out) for
RGB1.)
The original factory settings for the items of this Menu page can be
restored by pressing the OK button. (This is effective only for RGB2.)
(off the function)
(waiting to reset)
Reset
Normally set to 0.7 V. If white is found to spread across the screen, set
to 1.0 V. (This is effective only for RGB2.)
0.7V
Off
1.0V
On
Input Level
Set this to Off if the frequency information of the Input Signal Screen
Display is not required.
Frequency Display
This is only available for W-VGA signal.
When it is set to On, the display area modecan be selected Full or
Real.
Off
Off
On
WVGA Type
On
PC
Turn On when concerned about screen flicker.
Vertical Filter
Movie
Set to Movie when viewing moving images on a personal computer.
Frequency Mode
Optional (grayed out)
Optional (grayed out)
RGB1
RGB2
* Depending on the type of signal displayed, displays may not be optimized through automatic adjustment. Adjust manually to optimize them.
20
LANGUAGE MENU
Language
Picture
Audio
Timer
English
Français
Deutsch
Español
Italiano
Norsk
OK
MENU
Function
Setup
Language
Select
Svenska
OK Set
Select
Return
Exit
▲
Select a language by ▼ SELECT buttons and press the OK button.
OTHER FEATURES
Automatic Store
Approximately 1 sec. after adjustment is completed, the adjustments will be recorded as shown in the table below.
Menu
Picture
Display
Registration condition
For every input function, 1 setting
is registered.
Menu
Function
Display
Screen Saver
Screen Wipe
Black Side Panel
Panel Life
Registration condition
1 setting is registered.
(not registered)
Contrast
Brightness
Colour
(not registered)
1 setting is registered.
Hue
Mode Display
ID Number
Picture Enhancement
Colour temperature
Inverse
Colour Temp. Adjust
Standby White
Gamma
For every Colour Temperature, 1
setting is registered.
R Amplitude
G Amplitude
B Amplitude
R Cut Off
Setup
Auto Adjust
(not registered)
For every signal Mode, 1 setting is
registered. (Only for RGB2)
Horizontal Position
Vertical Position
Horizontal Clock
Clock Phase
Input Level
G Cut Off
B Cut Off
Audio
Audio Mode
Treble
1 setting is registered.
1 setting is registered.
For every Audio Mode, 1 setting is
registered.
Frequency Display
WVGA Type
Bass
Balance
1 setting is registered.
Vertical Filter
Frequency Mode
SRS TruBass
Matrix Surround
Perfect Volume
For every Audio Mode, 1 setting is
registered.
Language
1 setting is registered.
• The previously recorded items will be lost.
• The signal mode can be identified by the horizontal/vertical sync
frequency and the sync signal polarity. Different signals with which
all the elements are the same or similar will be handled as the
same signal.
21
OTHER FEATURES (continued)
Signal Check
Changes in the signal status are displayed on the screen as they arise.
RGB
Status
Display
Action
When Mode Display is set to ON,
the input signal is switched or
when the RECALL button is
pressed.
A guide is displayed for the input
terminal and the horizontal and
vertical sync frequency.
RGB2
RGB
H : 48.4kHz
V : 60.1 Hz
-- -- Min.
-- -- : -- --
OFF
When the sync signal is no longer • A guide displays No Sync.
Recheck the personal computer
power switch status and the
connection status.
detected.
Signal, and Power Save (for
approx. 5 sec.)
• When the condition continues
where the sync signal cannot be
detected, indicator lamp of
power source changes in
orange and the mode switches
to power save mode.
! No Sync. Signal
When the input signal does not
match the monitor specifications
or is in an unstable status.
A guide displays Invalid Scan
Freq.
Recheck the input signal
specifications.
27
29
~
! Invalid Scan Freq.
Power Save Mode
When the RGB, RGB2 input is selected
• When this unit is connected to a VESA DPMS computer, the Power Save (Off) mode can be set to be activated automatically when the
computer is not being used to reduce power consumption by this unit.
Horizontal
Vertical
Yes
Yes
No
Yes
No
No
No
RGB sync signal
PC signal
Yes
Active (normal display)
Blank (no display)
Operation mode
Indicating lamp
On
Off
Lights green
Lights orange
3W or less (RGB1)
1W or less (RGB2 ; 100V AC 120V)
255W (32")
365W (42")
<
<
Power consumption
<
3W or less (RGB2 ; 120V<AC 240V)
Returning to operating status
• Operate the personal computer, or press either the INPUT SELECT button of the main unit or the RGB1/RGB2 buttons of the remote control.
22
IMAGE RETENTION OF PLASMA DISPLAY
There are different characteristics that result in panel image retention depending on how the plasma display is used.
Situations and effective usage methods related to ghosting are provided below.
Image retention characteristics of a plasma display
The image retention phenomenon of a plasma panel occurs due to partial phosphor degradation arising from partial character and figure
display.
For example, when the character image as shown in Fig. A at the right is
continuously displayed for a long period of time, the only part of the phosphor
(Red,Green, Blue) that will degrade will be the colour of the applicable character
display portion. Consequently, when a white image is displayed on the entire
screen as shown in Fig. a, the character marks displayed up to that time will
become a colour difference visible to the eye, but the phosphor will never burn.
[Fig. A]
[Fig. a]
The degree of image retention is proportional to the brightness of the characters and figures displayed as well as the display time.
■
• The tendency of the phosphor is to degrade more the brighter the characters
and figures are displayed. When images of figures with different levels of
brightness, as shown in Fig. B, are continuously displayed for a long period of
time, it becomes easier for image marks at locations when the brighter figures
are displayed to be noticeable.
[Fig. B]
[Fig. b]
✻
The image retention images in this document are exaggerated for the purpose of explanation. The actual manner in which the image retention
is seen differs depending on the operation time and brightness.
Methods to Reduce the Occurrence of Image Retention
• Lower the Contrast and Brightness settings of the plasma display as much as possible.
A function is provided in the display that controls the brightness of the screen to reduce degradation of the panel. Using this function makes it
possible to reduce image retention.
(Refer to Panel Life (Extend 1.or Extend 2 shown on 19
)
• Set the plasma monitor to an “Screen Wipe” or “Inverse” display.
The occurrence of image retention when displaying images of identical patterns, such as static images, for long periods of time can be
reduced by displaying a reversed colour or completely white screen for about 1 ~ 2 hours after terminating the display.
(Settings can be made using Screen Wipe and Inverse of Function MENU shown on
)
19
• Using in combination with moving images
Since the degradation of the fluorescent material progresses comparatively uniform for moving images, the occurrence of partial image
retention can be controlled. We recommend to use in combination with moving images such as a DVD.
* Please be careful since image retention will occur if display is left in a two screen display state for a long period of time.
* Television broadcasts include images displayed for long periods of time in which the left and right or top and bottom of the image are cut and
broadcast station name or time are displayed for a long period of time at the same portion of the screen. Image retention in these portions can
be expected to occur, so please be aware.
NOTES
About screen defects
• High precision technology is used in the making of plasma panels but there may be dark spots (points that do not illuminate) and bright spots
(points that are too bright) in some cases. These do not indicate a malfunction.
About residual images
• In some cases, residual images may remain after the short-term display of still images and another image is displayed, but these will
disappear and return to normalcy. This is not a malfunction.
About the panel screen
• Plasma displays display images by means of electrical discharges inside the panel. Because of this, the temperature of the panel surface may
rise in some cases.Also, plasma displays are made of finely processed glass. A reinforced glass filter is installed over the panel surface but
avoid strong impact because there is still danger of glass breakage.
23
TROUBLESHOOTING
Symptoms That Seemingly Appear to be Failures
Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer.
WARNING
Customer servicing can be hazardous.
Symptom
Point to check
See page
• No picture with the power-indicating lamp
off.
• Check the way the power cable is connected.
• Press the power switch.
12
13
• The message “No Sync. Signal” or “Power
Save” is displayed.
No sync signal is detected.
11
• Check the way the signal cable is connected.
• Make sure that the switch of the computer, imaging equipment ,
etc., is turned on.
• Make sure the computer is not in the power-save mode.
• Check to see if the input selection matches the connection
terminal.
! No Sync. Signal
• No picture with the power indicating lamp
lights in orange.
• The message “Invalid Scan Freq.” is
displayed.
An input signal is not received normally.
• Check to see if the input signal matches the monitor
specifications.
11
! Invalid Scan Freq.
28
29
• Check the way the signal cable is connected.
• The power indicating lamp is normally lit but
no picture .
• Check the contrast and brightness settings (adjust them for higher
contrast and brightness).
• Check the way the signal cable is connected.
11
17
• The display image appears flowing
slantwise.
• Text displayed across the screen appears
vertically streaked, with the characters in
vertical columns blurred.
• Adjust the dot clock frequency and phase. (Adjust the dot clock
frequency first, the dot clock phase next.)
(RGB input)
20
26
• Text displayed across the screen appears
blurred.
• Adjust the dot clock phase for the clearest viewing.
(RGB input)
20
26
• A fine pattern flickers when displayed on the
screen.
• The remote control does not work.
• Check to see if the batteries are loaded in the remote control in
opposite direction.
9
• Check to see if the batteries in the remote control are OK.
24
Symptom
Point to check
See page
• The temperature of the display panel surface is high.
• The plasma display panel is lighting the phosphors by the
discharge of internal radiation. In some cases, this may cause the
temperature of the panel surface to increase. Please note that this
is not a malfunction.
-
• There are locations on the screen that are different from the • High-precision technology is used to manufacture the plasma
periphery (*).
display panel, However in some cases, there are minor defects in
some parts of the screen. Please note that this is not a
malfunction.
*Points that do not light, points with brightness different
from that of the periphery, points with color different from
that of the periphery, etc.
-
• Vertical stripes appear, depending on the screen contents. • The plasma display panel is lighting the phosphors by the
discharge of internal radiation. Depending on the screen contents,
in rare cases this may cause vertical stripes to appear because of
failure to light. Please note that this is not a malfunction.
-
• Coarse horizontal stripes appear in FULL display.
• Adjusting the Clock Phase will reduce the horizontal stripes.
(RGB input)
20
20
• Flickering in the form of horizontal lines oscillating up and
down.
(PC INPUT MODE only)
• If the direct frequency from the computer is below 85Hz, try a
higher frequency (upper limit 85Hz). There may be a slight
attenuation of the current image.
• Try turning the Vertical Filter On. For this case however, the
vertical resolution will drop.
• The fan motor is noisy. (Fan application model only)
• Use the fan that controls the temperature in the main body to lower
the temperature of this unit. If the ambient air temperature
increases, the fan will start, the RPMs will increase and motor
noise will grow louder. This is not a malfunction though.
-
• The top of the monitor heats up.
• When used for long periods of time, the top of the monitor may
heat up. This is not a malfunction.
-
-
• Text characters are displayed with varying thicknesses.
• The thicknesses of characters and lines may vary if images with a
vertical resolution greater than 512 lines are displayed; however,
this is not a malfunction.
25
TROUBLESHOOTING (continued)
Actions to Correct Abnormal Displays
Depending on the kind of system equipment used, images may not be displayed normally. In this case, make the
adjustments suggested below. (only for RGB2)
Text displayed across the screen appears vertically streaked, with some characters blurred (figure 1).
The display image appears flowing (figure 2) (RGB input).
Symptom 1
Vertical
streaks
Before adjustment
Some characters
are blurred.
Figure 1
After adjustment
All characters appear
crisp now.
ABCDEFGHIJ
ABC
AABBCC
abcdefgABCDEFGabcd
ABCDEFGHIJ
abcdefgABCDEFGabcd
ABC
Example
After adjustment
All characters are
blurred.
1) Press the AUTO button on the remote control.
When adjustment is not possible with Auto Adjust
2) Press the MENU button. The Main Menu will be displayed.
3) Press the SELECT button and select Setup.
4) Press the OK button. The Setup Menu will be displayed.
5) Press the SELECT button and select Horizontal Clock.
(Display fine patterns as characters or a vertical striped pattern over the entire screen during Horizontal Clock adjustment.)
6) Press the or ADJUST buttons and search for clear characters over the entire screen.
7) Perform adjustment for symptom 2 below, when the characters are blurred on the entire screen.
Adjustment
procedure
• The display image may be momentarily disturbed during clock adjustment but this is not a failure.
Text displayed across the screen appears blurred in its entirety (figure 2).
Symptom 2
A fine pattern flickers when displayed on the screen (figure 3).
Before adjustment
Before adjustment
Figure 3
Figure 2
ABCDEFGHIJ
abcdefgABCDEFGabcd
ABCDEFGHIJ
abcdefgABCDEFGabcd
AABBCC
Example
After adjustment
After adjustment
ABC
1) Press the AUTO button on the remote control.
When adjustment is not possible with Auto Adjust
2) Press the MENU button. The Main Menu will be displayed.
3) Press the
4) Press the OK button. The Setup Menu will be displayed.
5) Press the SELECT button and select Clock Phase.
(Display fine patterns as characters or a vertical striped pattern over the entire screen during Clock Phase adjustment.)
SELECT button and select Setup.
Adjustment
procedure
6) Press or ADJUST buttons to make the text appear 6) Press or ADJUST buttons to make the text appear
clean across the screen. without flickering.
26
PRODUCT SPECIFICATIONS
Product specifications and designs are subject to change without notice.
Display
dimensions
Approx. 32 inches (716 (H) x 399 (V) mm, diagonal 820mm)
Approx. 42 inches (922 (H) x 522 (V) mm, diagonal 1059mm)
1024 (H) x 1024 (V) pixels
Panel
Resolution
Net dimensions
852 (H) x 1024 (V) pixels
830 (W) x 506 (H) x 92 (D) mm
1030 (W) x 636 (H) x 91 (D) mm
(excluding Speakers/Stand)
Net weight
(excluding Speakers/Stand)
24.6kg
34.9kg
Temperature
Ambient
Operating : 5˚C to 35˚C, Storage : 0˚C to 40˚C
conditions
Relative humidity Operating : 20% to 80%, Storage : 20% to 90% (non-condensing)
Power supply
AC100 - 240V, 50/60Hz
Power consumption/at standby 255W / <3W
365W / <3W
Audio output
(RGB input)
12W + 12W (6Ω)
RGB1 DVI input terminal (DVI-D)
RGB1 audio input terminal (3.5mm Stereo Mini Jack)
RGB2 analog RGB input terminal (D-sub 15-pin)
RGB2 audio input terminal (3.5mm Stereo Mini Jack)
Input terminals
Input signals
Video signals
Sync signals
0.7 V/1.0 Vp-p, analog RGB (Recommended Signal)
H/V separate, TTL level [2KΩ]
H/V composite, TTL level [2KΩ]
Sync on green, 0.3 Vp-p [75Ω]
Recommended signal
43 modes 28
29
• The monitor takes at least 30 minutes to attain the status of optimal picture quality.
Signal Input
RGB terminal (D-sub 15-pin connector)
5
4
3
2
1
Pin
1
Input signal
10
9
8
7
6
R
G or sync on green
B
2
15
14
13
12
11
3
4
No connection
No connection
R.GND
• When different kinds of input signals are simultaneously input to
the monitor via a graphics board or the like, the monitor will
automatically select the signals in the following priority order:
5
6
Sync signal type
H/V separate sync.
H/V composite sync.
sync.on Green *
Priority
7
G.GND
1
2
3
8
B.GND
9
No connection
GND
10
11
12
13
14
15
*Even in the case of the recommended signals shown on the
following page, there may be instances when correct display is
not possible. In this case, use H/V separate sync, H/V composite
sync.
No connection
[SDA]
H. sync or H/V composite sync
V.sync. [V.CLK]
[SCL]
27
PRODUCT SPECIFICATIONS (continued)
Signal Input (continued)
DVI terminal (DVI-D)
Pin
1
Input signal
T.M.D.S. Data2-
T.M.D.S. Data2+
T.M.D.S. Data2/4 Shield
T.M.D.S. Data4-
T.M.D.S. Data4+
DDC Clock
Pin
14
15
16
17
18
19
20
21
22
23
24
Input signal
+5V Power
1
9
2
3
4
5
6
7
8
2
Ground (for+5V)
Hot Plug Detect
10 11 12 13 14 15 16
3
17 18 19 20 21 22 23 24
4
T.M.D.S. Data0-
T.M.D.S. Data0+
T.M.D.S. Data0/5 Shield
T.M.D.S. Data5-
T.M.D.S. Data5+
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock-
5
6
7
DDC Data
8
No Connect
9
T.M.D.S. Data1-
10 T.M.D.S. Data1+
11 T.M.D.S. Data1/3 Shield
12 T.M.D.S. Data3-
Frame GND
13 T.M.D.S. Data3+
Recommended Signal List
With Digital RGB signal input (RGB1 input)
Signal mode
Horizontal frequency Dot clock frequency
No.
Remarks
Vertical frequency
(Hz)
(kHz)
(MHz)
Signal Name
VGA
Resolution
1
2
640 X 400
640 X 480
864 X 480
864 X 480
640 X 480
640 X 480
640 X 480
800 X 600
800 X 600
800 X 600
800 X 600
800 X 600
1024 X 768
1024 X 768
1024 X 768
70.08
59.94
60.00
59.94
72.81
75.00
85.01
56.25
60.32
72.19
75.00
85.06
60.00
70.07
75.03
31.47
31.47
31.02
31.47
37.86
37.50
43.27
35.16
37.88
48.08
46.88
53.67
48.36
56.48
60.02
25.18
25.18
33.75
34.24
31.50
31.50
36.00
36.00
40.00
50.00
49.50
56.25
65.00
75.00
78.75
3
W-VGA
4
WVGA type : On
5
6
7
8
9
10
11
12
13
14
15
VESA
• Make sure that the signal of the equipment to be connected is compatible with the specifications of this list.
28
With Analog RGB signal input (RGB2 input)
Signal mode
Horizontal frequency Dot clock frequency
No.
Remarks
Vertical frequency
(Hz)
(kHz)
(MHz)
Signal Name
VGA
Resolution
1
2
640 X 400
640 X 480
70.08
59.94
31.47
31.47
25.18
25.18
3
W-VGA
864 X 480
59.94
31.47
34.24
WVGA type:On
4
640 X 480
640 X 480
72.81
75.00
85.01
56.25
60.32
72.19
75.00
85.06
60.00
70.07
75.03
85.00
75.00
60.02
75.03
85.02
60.00
75.00
85.00
66.67
74.55
74.93
75.06
59.833
69.997
37.86
37.50
43.27
35.16
37.88
48.08
46.88
53.67
48.36
56.48
60.02
68.68
67.50
63.98
79.98
91.15
75.00
93.75
106.25
35.00
49.72
60.24
68.68
47.986
56.137
31.50
31.50
36.00
36.00
40.00
50.00
49.50
56.25
65.00
75.00
78.75
94.50
108.00
108.00
135.00
157.50
162.00
202.50
229.50
30.24
57.28
80.00
100.00
81.00
94.760
5
6
640 X 480
7
800 X 600
8
800 X 600
9
800 X 600
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
800 X 600
800 X 600
1024 X 768
1024 X 768
1024 X 768
1024 X 768
1152 X 864
1280 X 1024
1280 X 1024
1280 X 1024
1600 X 1200
1600 X 1200
1600 X 1200
640 X 480
VESA
832 X 624
Macintosh
W-XGA
1024 X 768
1152 X 870
1280 X 768
1280 X 768
• The type of video board or connecting cable used may not allow for correct displays adjustment of Horizontal Position, Vertical Position, Horizontal
Clock and Clock Phase.
• The monitor may fail to display an animation image correctly when a signal having a vertical frequency of 85Hz or higher is input to it.
• The monitor differentiates the signal modes according to the horizontal and vertical frequencies and the horizontal and vertical sync signal
polarities. Note that different signals having all these elements alike may be handled as the same signal.
• Displaying images with more than 512 lines of vertical resolution at Full diplay (compressed display) can result in the interpolation of stripes.
29
SUPPLEMENT
30
Optional Video Unit Function
31
42
Additional functions when the optional video unit is installed are as follows: (
~
)
INSTALLATION INSTRUCTIONS
Connecting to a Video Imaging Device
(1) Make sure that the power switch of the monitor is turned off.
(2) Make sure that the power switch of the imaging device is turned off.
(3) Use a commercially available cable and connector to connect the signal input terminal on the rear panel of this
device and the signal output terminal of the imaging device.
Speaker (R)
Speaker (L)
Monitor rear panel
Power
cord
20 18 16 14 12 10
8
6
4
2
DVD player
DVD player
21 19 17 15 13 11
9
7
5
3
1
VCR
To RGB,
video and audio
input terminals
To SCART
terminal
[An example of connecting video imaging devices]
Use if the
video
equipment
has an
S video
Set-Top Box
VCR
input terminal
• If video equipment with an S video output terminal is used, cabling
With DVI-STB and RGB component setup
by the S video cable is recommended to provide finer video
quality. (If the S video input terminal and the video input terminal of
AV3 connect to the monitor at the same time, S video input would
govern.)
• If the OUTPUT (MONITOR) terminal is connected to an external
monitor with a 75 Ohm terminal, it is possible to view the same
image as on the main unit. But it is possible to monitor only the
composite video signal from AV1, AV2, AV3, or AV4 input that is
displayed on the screen at the time.
To component video
equipments.
Please use the connection
cable suitable for the terminal
form of video equipment.
40
Applicable video signals for each input terminal (See PRODUCT SPECIFICATIONS for details.
)
Terminal
Signal
AV1
RCA/SCART
CVBS S-video Component
DVI
D-sub
RGB Component
Remarks
RGB
PC
STB
38
38
AV2
AV3
Refer to Setup Menu.
Refer to Setup Menu.
AV4
RGB1
RGB2
Refer to Setup Menu. 39
39
Refer to Setup Menu.
: Available)
(
31
OPERATING INSTRUCTIONS
VOL
VOL
RGB
AV1
1
RGB
AV2
2
MUTE
AV3
RGB/VIDEO
buttons
AV4
AUTO
MENU
PinP
SIZE
RECALL
SIZE button
INPUT SELECT button
SIZE button
OK
Input Switching
•
•
Input can be switched by pressing the AV1, AV2, AV3,
AV4, RGB1 or RGB2 buttons of the remote control.
Input can be switched in the sequence of AV1 AV2
➔
➔
AV1
AV2
RGB1
AV3
AV4
AV3 AV4
RGB1 RGB2 by pressing the INPUT
➔
➔
➔
SELECT button of the monitor.
RGB2
Size Switching
Each time the SIZE button of the remote control or the
monitor is pressed, the screen display size will change in
sequence and the status will be displayed at the bottom
of the screen.
• During VIDEO signal input (AV1, AV2, AV3)
• During AV4 signal input
Panoramic
14:9Zoom
4:3
Full
Auto
Full
Zoom
C14:9L
C14:9L
Zoom
14:9Zoom
• The size will fix as Full mode and not change when receiving the
component signal of 1080i/50, 1080i/60 or 720p/60.
• [Auto] is the mode using the Switch signal from the equipment
connected to AV4 terminal included in SCART connector No.8 pin
which indicate the picture format of the video source. When Switch
signal has not been detected, Default Zoom setting in the Function
Menu is used to choose.
• And during some input mode except AV4, if the Switch signal is
detected under the condition that [Auto] is selected for the picture
size of AV4, the input mode will automatically transfer to AV4.
Full
Display size selection diagram
When you want to
Set the display size to
Input signal
(4:3 signal)
Display screen
Remarks
Play a 4:3 image in a 16:9 screen faithfully.
Blanking occurs on both sides.
4 : 3
Play a 4:3 image in a 16:9 screen with the
height and width of the middle of the
screen enlarged on equal scales and with
both sides appearing somewhat enlarged.
Panoramic
Zoom
Play a 16:9 VISTA size image in the 4:3
image faithfully reproduced on the 16:9
screen.
• The 4:3 image is called a letterbox image.
• In some cases, some slight blanking may
remain at the top and bottom.
(Vista)
Play a 4:3 image faithfully in a 16:9 screen
in the standard vertical size and
horizontally squeezed.*
* An image with an aspect ratio of 16:9
shrunk horizontally to 4:3 to display in a 4:3
screen
Full
(Squeeze)
(14:9 signal)
(14:9 signal)
Play a 14:9 image in a 16:9 screen
expanded vertically and squeezed
horizontally.
This mode is provided for the broadcasting
program with WSS code-C14:9L.
C14 : 9L
14 : 9Zoom
Play a 14:9 image expanded vertically on
the 16:9 screen.
This mode is provided for the broadcasting
program with WSS code-14:9Zoom.
32
Vertical picture position can be adjusted for [Panoramic], [Zoom] , [C14:9L] and [14:9Zoom] mode as follows.
1. Press SIZE button and
SELECT buttons during picture size display.
2. Position display will appear.
3. Adjustment range of each picture size are as shown below.
[Panoramic]
- 12 to + 12
[Zoom]
[C14:9L] and [14:9Zoom]
- 31 to + 31
- 16 to + 16
4. When 1080i/50 or 1080i/60 component signal is received, vertical position can be adjusted only one step up. (The range: 0 to +1)
Position + 31
Position - 31
Press
Press
ATTENTION
Using a wide-screen monitor
• This monitor has a screen mode selection feature. If an incompatible screen mode is selected to play certain software, such as a TV program,
the image would appear different from the original. Take this into consideration when making screen mode choices.
• Use of this monitor in its enlarged display mode with the wide feature enabled in coffee shops, hotels and other establishments for
commercial or pubic viewing purposes could infringe on the copyright holder’s right protected by Copyright Law.
• When a normal 4:3 image is displayed over the entire screen in the Panoramic mode, parts of the periphery of the image may disappear
and/or appear distorted in some cases. Use the 4:3 mode to view images, which were created in 4:3 mode.
This mode allows 4:3 content to be viewed without picture distortion.
33
OPERATING INSTRUCTIONS (continued)
Displaying MULTI PICTURE
If the PinP button on the remote control is pressed MULTI
PICTURE will display.
Activating the P-in-P mode from the RGB input screen
Pressing the PinP button one time will display 2 pictures.
• This mode can be available from RGB1(DVI-PC) and RGB2(RGB)
input.
• The speaker icon can be shifted left and right by pressing the
and
SELECT buttons; the audio of the video will be output from
RECALL button
the side on which the speaker icon
is located.
RGB2
AV1
• The sub-screen position can be
selected up and down by pressing
SELECT buttons.
• The sub-screen can be selected with
the AV1, AV2, AV3, and AV4 buttons
from the status that the speaker icon
appears on the left side of AV✱ as
shown in the diagram to the right.
(Sub-
screen)
VOL
VOL
• Pressing the PinP button again or the RETURN button will cancel
the 2 pictures display.
PinP button
RGB 1
AV1
RGB 2
AV2
MUTE
AV3
RECALL button
• "Frequency Mode" in the Setup Menu should be set to Movie when
AV4
sub-screen is the component signal of 1080i/50 or 1080i/60.
AV1: Displays the VIDEO input signal of the sub-screen.
AUTO
MENU
PinP
SIZE
RECALL
Activating the Split mode from the video input screen
Pressing the PinP button one
time will display 2 pictures.
AV1
AV2
OK
RETURN button
• The speaker icon can be shifted left
and right by pressing the and
SELECT buttons; the audio of the
video will be output from the side on
ID
ID SET
which the speaker icon is located.
• The same video input mode cannot
be selected for both screens at the same time.
• Pressing the PinP button again or the RETURN button will cancel
the 2 pictures display.
•
•
When the Video input is set to RGB Video, this Split mode is not possible.
Refer to the table for 2 pictures (Split) mode.
2 Pictures (Split)
Input terminal
AV1~AV4
AV1, AV2
RGB1
RGB2
PAL
NTSC3.58 576i 480i
Sub
1080i/50 1080i/60 720p/60 STB Component
Main
SECAM NTSC4.43 576p 480p
Main
Sub
PAL, SECAM
AV1
~AV4
NTSC3.58/4.43
576i, 576p
480i, 480p
1080i/50
AV1
AV2
1080i/60
720p/60
RGB1
RGB2
STB
Component
: Available)
(
NOTE
• Even if the input of the horizontal / vertical synchronizing signal (or video signal) stops in the MULTI PICTURE display, the mode will not
change to power save mode.
• Please be careful since image retention will occur if display is left in a MULTI PICTURE display state for a long period of time.
Input Signal Screen Display
Input mode
Signal mode
VIDEO
AV1
Composite
The input signal status can be displayed on the screen
by pressing the RECALL button of the remote control or
the monitor.
• The display will go out in approximately 6 seconds.
-- -- Min.
-- -- : -- --
OFF
Off-timer
On-timer
34
PICTURE MENU
Picture
Picture Mode
Contrast
Brightness
Colour
Sharpness
Hue
Colour Temperature
Contrast Mode
Reset
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Dynamic
+31
-31
0
+15
OK
OK
MENU
0
Normal
Normal
Reset
Return
Picture Mode
Next/Prev
Dynamic
Return
Select
Set
OK
Select
Picture
Picture Mode
Contrast
Brightness
Colour
Dynamic
+31
-31
OK
0
Sharpness
Hue
Colour Temperature
Contrast Mode
Reset
+15
0
Normal
Normal
Reset
Return
Contrast Mode
Next/Prev Select
Normal
Return
Select
Set
OK
Picture
YNR
Dynamic
Off
OK
OK
OK
OK
OK
CNR
Film Mode
PAL Comb Filter
LTI
CTI
Black Enhancement
Auto Colour
Reset
Off
On
On
Off
Off
Off
Off
Reset
Return
YNR
Next/Prev
Off
Return
Select
Set
OK
Select
Picture
YNR
CNR
Film Mode
PAL Comb Filter
LTI
CTI
Black Enhancement
Auto Colour
Reset
Dynamic
Off
Off
On
On
Off
Off
Off
Off
Reset
Return
Auto Colour
Next/Prev
Off
On/Off
Return
Select
Set
OK
Picture
Picture
Dynamic
Return
Colour Temp. Adjust
Amplitude
Red
On
Colour Temp. Adjust
Colour Management
Colour Decoding
– 63
0
– 31
Green
Blue
Cut Off
Red
Green
Select OK Set
+ 31
0
+ 31
Blue
Reset
Select
Reset
Return
On/Off
Picture
Colour Management
Picture
Dynamic
Return
On
Colour Temp. Adjust
Colour Management
Colour Decoding
Magenta
Red
Yellow
Green
Cyan
+ 60
+ 30
0
+ 60
+ 30
0
Select
Set
OK
Blue
Reset
Select
Reset
Return
On/Off
Picture
Colour Decoding
Picture
Dynamic
Return
Colour Temp. Adjust
Colour Management
Colour Decoding
RGB
Red
Green
Colour
Hue
R
G
B
0
+ 60
0
Select
Set
OK
+ 31
Reset
Reset
Exit
Select
Return
35
OPERATING INSTRUCTIONS (continued)
PICTURE MENU (continued)
Selected characters
Setup hint
Dynamic: This setting is best for very bright ambient lighting.
Natural: This setting is for normal lighting conditions.
Dynamic
Natural
Picture Mode
Adjust for maximum visibility to suit the ambient brightness.
This can adjust further till [+40] by pressing and holding
cursor
button at [+31]. The color for [+32] to [+40] numbers will change from
white to magenta. This special mode is better for dark scenes.
For normal viewing we recommend that the Contrast is set to [+31].
"Panel Life" in the Function Menu should be set to Normal when this
Contrast setting is adjusted.
Narrows the gap between
brightness and darkness.
Broadens the gap between
brightness and darkness.
Contrast
Adjust to taste.
Black is subdued for
increased overall darkness.
Black is set off for increased
overall brightness.
Brightness
Colour
Darkens colours.
Soft
Lightens colours.
Sharp
Adjust to taste.
Normally set to Centre position Shift to the minus (-) side for a softer
effect and plus (+) for sharper picture.
Sharpness
This is not available to adjust when receiving PAL/SECAM signal.
Then the character will be grayed out.
Adjust for most realistic skin colour.
Enhances red and weakens
green.
Enhances green and weakens
red.
Hue
Cool
Normal
Warm
Black / White
Normally set to Cool.
Colour Temperature
Dynamic:Emphasizes the differences between video shadings to
improve the feeling of contrast.
Normal : The gradation of an image is reproduced as faithfully as
possible.
Normal
Auto
Dynamic
Contrast Mode
Auto:Detects image brightness and automatically adjusts for natural
brightness.
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
(off the function)
(waiting to reset)
Reset
YNR
Performs picture signal noise reduction. Turn up to reduce noise.
Off
Low
High
Performs colour signal noise reduction. Turn up to reduce noise.
And it will be fixed as Off only when selecting DVI-STB mode.
CNR
On:Automatically detects the movie film material and faithfully
reproduces the original film image.
Off:Set to OFF when switching between images does not appear
natural.
Off
Off
On
On
Film Mode
This is available only when receiving a PAL composite signal. Turn On
to reduce the discolorations in fine picture detail and provides purer
colour.
PAL Comb Filter
Adjusts the sharpness of the picture signal.
Adjusts the sharpness of the colour signal.
Adjusts the black level compensation.
LTI
Off
Low
Middle
High
CTI
Black Enhancement
This is available only when receiving an NTSC composite/S.Video
signal. This monitors and adjusts the colour to maintain constant
colour levels. It also maintains natural flesh tones while preserving
fidelity of background colours.
Off
Off
On
On
Auto Colour
Turn On when you wish to change colour temperature depending on
the user’s preference.
Colour Temp. Adjustment
Brighter scene is decreased in Brighter scene is increased in
reddish colour. reddish colour.
Amplitude
Red
Brighter scene is decreased in Brighter scene is increased in
greenish colour. greenish colour.
Green
Blue
Brighter scene is decreased in Brighter scene is increased in
Adjust colour temperature depending on the user’s preference. These
settings are independently stored in each of the 4 Colour Temperature
modes.
bluish colour.
bluish colour.
Dark scene is decreased in
reddish colour.
Dark scene is increased in
reddish colour.
Cut Off
Red
Dark scene is decreased in
greenish colour.
Dark scene is increased in
greenish colour.
Green
Blue
Dark scene is decreased in
bluish colour.
Dark scene is increased in
bluish colour.
36
Selected characters
Setup hint
Turn On when the original balance of each colour is required to adjust
depending on the user’s preference.
Off
On
Colour Management
Magenta is weakened.
Red is weakened.
Yellow is weakened.
Green is weakened.
Cyan is weakened.
Blue is weakened.
Magenta is strengthened.
Red is strengthened.
Yellow is strengthened.
Green is strengthened.
Cyan is strengthened.
Blue is strengthened.
Magenta
Red
Yellow
Green
Cyan
This adjusts listed colours individually to make them either deeper or
more pure. These settings are independently stored in each of the 4
Colour Temperature modes.
Blue
Select the single colour screen when that is required to adjust R/G/B
level individually depending on the user’s preference. And set it back
to RGB mode that indicates all colour after adjusting.
RGB
R
G
B
Colour Decoding
Press the OK button every time the setting is changed.
Darkens red only.
Darkens green only.
Darkens colours.
Lightens red only.
Lightens green only.
Lightens colours.
Red
Green
Colour
Hue
This adjusts R/G/B level or tint to make the colour appear natural for
the user’s preference. These settings are independently stored in each
of the 4 Colour Temperature modes.
Enhances red and weakens
green.
Enhances green and weakens
red.
FUNCTION MENU
2 item is added to the Menu shown in the page
.
19
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Function
Screen Saver
Screen Wipe
Black Side Panel
Video Power Save
Freeze Mode
Default Zoom
Reset
Off
On 60Min.
Off
Off
Split
Panoramic
Reset
Return
OK
MENU
Select
Set
Function
Panel Life
Mode Display
ID Number
Inverse
Normal
Off
1
On 60Min.
Off
2.2
Standby White
Gamma
Reset
Select
Reset
Return
Set
Selected characters
Setup hint
This is used to reduce power consumption for video input when there
is no video signal. Setting it On will leads the monitor to the standby
mode when the AV input with no signal is selected.
Off
On
Video Power Save
This selects the screen display size that appears first when the power
turned on.
Panoramic
4:3
Default Zoom
14:9 Zoom
37
OPERATING INSTRUCTIONS (continued)
SETUP MENU
Picture
Audio
Timer
Function
Setup
Language
Select
Setup
Colour System
Setup
System
System 1
OK
OK
Colour System
Video Input
Audio Input
Scart Output
RGB1
MENU
AV1
AV2
AV3
AV4
Auto
PAL
SECAM
PAL
Monitor
DVI-STB
Component
HDTV
OK Set
RGB2
OK
Select
Return
Exit
Select
Set
Return
Setup
System
Setup
Video Input
System 1
OK
Colour System
Video Input
Audio Input
Scart Output
RGB1
AV1
AV2
AV3
AV4
Auto
Composite/Component
Auto
S.Video
Monitor
DVI-STB
Component
HDTV
RGB2
Select OK Set
Return
Select
Return
Exit
Setup
System
Setup
Audio Input
AV1
AV2
AV3
System 1
OK
Colour System
Video Input
Audio Input
Scart Output
RGB1
Stereo
L/Mono
Stereo
L/Mono
Monitor
DVI-STB
Component
HDTV
AV4
Select
Return
Exit
RGB2
Select
Set
Return
OK
Selected characters
System
Setup hint
Do not change the original setting.
(System1 : Europe/Asia, System2 : North America)
System1
System2
Colour System
This should correspond to the colour system of the signal from the
equipment that is connected to AV1 video input terminal.
• Normally, set this to Auto. The system of the input signal will be
automatically recognized.
• If the input signal contains much noise or has a low level at Auto and the
operation is found erratic, set this to match the input signal.
• When the component signal is received, this would be not available
(grayed out).
Auto
NTSC3.58
PAL
SECAM
NTSC4.43
AV1
AV2
AV3
AV4
(Same to AV1)
Video Input
This should correspond to the signal mode of the signal from the
equipment that is connected to AV1 video input terminal.
• Normally, set this to Auto. The signal mode of the input signal will be
automatically recognized.
Auto
HDTV
SDTV/DVD
AV1
• If the input signal contains much noise or has a low level at Auto and the
operation is found erratic, set this to match the input signal.
This should correspond to the signal mode of the signal from the
equipment that is connected to AV2 video input terminal.
RGB
Auto
Composite/Component
AV2 (1st step)
AV2 (2nd step)
This step should be set only when [Composite/Component] is selected on
the 1st step. And the procedure is same to AV1.
HDTV
SDTV/DVD
• If the signal from the equipment that is connected to AV4 Scart input
terminal is S.Video or Composite, set this to correspond to that signal.
• If the signal is RGB, it will be automatically recognized and this setting
will have no effect.
S.Video
Composite
AV4
38
Selected characters
Setup hint
Audio Input
This should correspond to the audio signal from the equipment that is
connected to AV1 audio input terminal. If it is monaural audio, set this to
L/Mono.
Stereo
L/Mono
AV1
AV2
AV3
AV4
(Same to AV1)
Not Available (grayed out)
Scart Output
RGB1
This should correspond to the signal mode of the signal from the
equipment that is connected to RGB1 DVI terminal.
DVI-PC
RGB
DVI-STB
This should correspond to the signal mode of the signal from the
equipment that is connected to RGB2 D-sub terminal.
Component
RGB2 (1st step)
This step should be set only when [Component] is selected on the 1st
step.
This should correspond to the signal mode of the signal from the
equipment that is connected to RGB2 D-sub terminal.
• Normally, set this to Auto. The signal mode of the input signal will be
automatically recognized.
Auto
HDTV
SDTV/DVD
RGB2 (2nd step)
• If the input signal contains much noise or has a low level at Auto and the
operation is found erratic, set this to match the input signal.
OTHER FEATURES
Automatic Store
Approximately 1 sec. after adjustment is completed, the adjustments will be recorded as shown in the table below.
Menu
Picture
Display
Picture Mode
Contrast
Registration condition
Menu
Picture
Display
Registration condition
1 setting is registered.
1 setting is registered.
For every input function and every
Picture Mode, 1 setting is
registered.
Yellow
Green
Cyan
Blue
Brightness
Colour
-
Sharpness
Hue
Colour Decoding
For every Colour Temperature, 1
setting is registered.
Red
Colour Temperature
Contrast Mode
YNR
Green
For every input function and every
Picture Mode, 1 setting is
registered.
Colour
Hue
CNR
Function
Setup
1 setting is registered.
Video Power Save
Film Mode
PAL Comb Filter
LTI
Default Zoom
System
1 setting is registered.
1 setting is registered.
Colour System
CTI
AV1
AV2
AV3
AV4
Black Enhancement
Auto Colour
Colour Temp. Adjust
R Amplitude
For every Colour Temperature, 1
setting is registered.
Video Input
Audio Input
-
G Amplitude
B Amplitude
R Cut Off
1 setting is registered.
AV1
AV2
AV4
G Cut Off
-
1 setting is registered.
AV1
AV2
AV3
AV4
B Cut Off
For every input function and every
Colour Management Picture Mode, 1 setting is
registered.
1 setting is registered.
Magenta
Red
RGB1
RGB2
• The previously recorded items will be lost.
39
TROUBLESHOOTING
Symptoms That Seemingly Appear to be Failures
Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer.
WARNING
Customer servicing can be hazardous.
Symptom
Point to check
See page
• This sometimes occurs when a component output VCR such as
the 480i is connected.
This is not a malfunction; therefore, please take note that this may
occur. When it does occur, change to composite output, or S.video
output.
• The screen becomes dark and the images cannot be seen
during VCR special playback (fast forward, rewind).
–
PRODUCT SPECIFICATIONS
This table shows the specifications when the optional video unit has been inserted.
Display
dimensions
Approx. 32 inches (716 (H) x 399 (V) mm, diagonal 820mm)
852 (H) x 1024 (V) pixels
Approx. 42 inches (922 (H) x 522 (V) mm, diagonal 1059mm)
1024 (H) x 1024 (V) pixels
Panel
Resolution
Net dimensions
(excluding Speakers/Stand)
830 (W) x 506 (H) x 92 (D) mm
1030 (W) x 636 (H) x 91 (D) mm
Net weight
(excluding Speakers/Stand)
24.6kg
34.9kg
Temperature
Operating : 5˚C to 35˚C, Storage : 0˚C to 40˚C
Ambient
conditions
Relative humidity Operating : 20% to 80%, Storage : 20% to 90% (non-condensing)
Power supply
AC100 - 240V, 50/60Hz
Power consumption/at standby 255W / <3W
365W / <3W
Audio output
(RGB input)
12W + 12W (6Ω)
RGB1 DVI input terminal (DVI-D)
RGB1 audio input terminal (3.5mm Stereo Mini Jack)
RGB2 analog RGB input terminal (D-sub 15-pin)
RGB2 audio input terminal (3.5mm Stereo Mini Jack)
Input terminals
Input signals
0.7 V/1.0 Vp-p, analog RGB (Recommended Signal)
480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
Video signals
Sync signals
H/V separate, TTL level [2KΩ]
H/V composite, TTL level [2KΩ]
Sync on green, 0.3 Vp-p [75Ω]
29
46 modes
42
Recommended signal
(Video input)
AV1: composite video input terminal (RCA)
AV1: Y PB PR video input terminal (RCA)
AV1: L/R audio input terminal (RCA)
AV2: composite video input terminal (RCA)
AV2: Y/G PB/B PR/R video input terminal (RCA)
AV2: L/R audio input terminal (RCA)
Input terminals
AV3: composite video input terminal (RCA)
AV3: S video input terminal (RCA)
AV3: L/R audio input terminal (RCA)
AV4: composite video / S video / RGB / L/R audio input terminal (Scart)
Input signals
AV1: PAL, SECAM, NTSC4.43, NTSC3.58
AV1: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
AV2: PAL, SECAM, NTSC4.43, NTSC3.58
AV2: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60, RGB
AV3: PAL, SECAM, NTSC4.43, NTSC3.58
AV4: PAL, SECAM, NTSC4.43, NTSC3.58
AV4: RGB
Video signals
OUTPUT (MONITOR): composite video monitor-output terminal (RCA)
OUTPUT (MONITOR): L/R audio monitor- output terminal (RCA)
AV4: composite video / L/R audio monitor-output terminal (SCART)
Video output Signal
42
15 modes
Recommended signal
• The monitor takes at least 30 minutes to attain the status of optimal picture quality.
40
Signal Input
RGB terminal (D-sub 15-pin connector)
5
4
3
2
1
Pin
1
Input signal
R (PR/CR)
10
9
8
7
6
2
G or sync on green (Y)
B (PB/CB)
15
14
13
12
11
3
4
No connection
No connection
R.GND (PR/CR, GND)
G.GND (Y, GND)
B.GND (PB/CB, GND)
No connection
GND
• When different kinds of input signals are simultaneously input to
the monitor via a graphics board or the like, the monitor will
automatically select the signals in the following priority order:
5
6
Sync signal type
H/V separate sync.
H/V composite sync.
sync.on Green *
Priority
7
1
2
3
8
9
10
11
12
13
14
15
*Even in the case of the recommended signals shown on the
following page, there may be instances when correct display is
not possible. In this case, use H/V separate sync, H/V composite
sync.
No connection
[SDA]
H. sync or H/V composite sync
V.sync. [V.CLK]
[SCL]
(
) : With component input
S-input connector pin specifications
1
Pin
Input signal
Y
3
1
2
Y-GND
C
2
4
3
4
C-GND
GND
Frame
Scart connector pin specifications
Pin
Signal
Pin
Signal
1
2
3
4
5
6
7
8
9
AUDIO OUT (RIGHT)
AUDIO IN (RIGHT)
AUDIO OUT (LEFT/MONO)
AUDIO GND
12 Not Used
13 RGB-R GND
14 GND
20 18 16 14 12 10
8
6
4
2
21
15 13 11
9
5
19 17
7
3
1
15 RGB-R / S.VHS CHROMINANCE IN
16 BLANKING SIGNAL
RGB-B GND
AUDIO IN (LEFT/MONO)
RGB-B IN
17 COMPOSITE VIDEO GND
18 BLANKING SIGNAL GND
19 COMPOSITE VIDEO OUT
AUDIO/RGB SWITCH / 16:9
RGB-G GND
20 COMPOSITE VIDEO / S.VHS LUMINANCE IN
10 Not Used
21 GND / SHIELD (CHASSIS)
11 RGB-G IN
41
PRODUCT SPECIFICATIONS (continued)
Recommended Signal List
With Digital RGB signal input (RGB1 input)
Signal mode
Resolution
Setup Menu Condition
Horizontal Dot clock
frequency frequency
No.
Remarks
Vertical frequency
(Hz)
Signal Name
VGA
DVI-PC
DVI-STB
(kHz)
(MHz)
1
2
640 X 400
640 X 480
864 X 480
864 X 480
640 X 480
640 X 480
640 X 480
800 X 600
800 X 600
800 X 600
800 X 600
800 X 600
1024 X 768
1024 X 768
1024 X 768
720 X 480
1280 X 720
1920 X 1080
70.08
59.94
60.00
59.94
72.81
75.00
85.01
56.25
60.32
72.19
75.00
85.06
60.00
70.07
75.03
59.94
60.00
60.00
31.47
31.47
31.02
31.47
37.86
37.50
43.27
35.16
37.88
48.08
46.88
53.67
48.36
56.48
60.02
31.47
45.00
33.75
25.18
25.18
33.75
34.24
31.50
31.50
36.00
36.00
40.00
50.00
49.50
56.25
65.00
75.00
78.75
27.00
74.25
74.25
3
W-VGA
4
WVGA type : On
5
6
7
8
9
10
11
12
13
14
15
16
17
18
VESA
480p
EIA-861
EIA-861
EIA-861
720p/60
1080i/60
: acceptable)
(
With Composite Input(AV1~AV4 input) and S-video Input (AV3 input).
Signal mode
Horizontal
Dot clock
No.
Remarks
Vertical frequency
(Hz)
frequency (kHz)
frequency (MHz)
Signal Name
Resolution
525
NTSC4.43
NTSC3.58
PAL
SECAM
1
2
59.94
15.73
15.63
—
—
625
50.00
With R, G, B Video input (AV2 and AV4 input).
Signal mode
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
No.
Remarks
Remarks
Vertical frequency
(Hz)
Signal Name
Resolution
525
625
59.94
50.00
15.73
15.63
NTSC4.43/3.58
PAL, SECAM
1
—
With component input (AV1, AV2 and RGB2-component input).
Signal mode
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
No.
Vertical frequency
(Hz)
Signal Name
Resolution
1
2
3
4
5
6
7
576i
480i
576
480
50.00
59.94
50.00
59.94
50.00
60.00
59.94
15.63
15.73
31.26
31.47
28.13
33.75
44.96
—
—
—
—
—
—
—
576p
576
480p
480
1080i/50
1080i/60
720p/60
1080
1080
720
• The monitor differentiates the signal modes according to the horizontal and vertical frequencies and the horizontal and vertical sync signal
polarities. Note that different signals having all these elements alike may be handled as the same signal.
• Displaying images with more than 512 lines of vertical resolution at Full diplay (compressed display) can result in the interpolation of stripes.
42
Optional Tuner Unit Function
The optional tuner unit can operate when installed with the optional video unit.
43
56
Additional functions when the optional tuner unit is installed are as follows: (
)
~
COMPONENT NAMES
Remote control (provided for the optional tuner unit)
9
This type of remote control would be provided for the optional tuner unit as the substitute for the one shown in page
.
POWER ON / OFF button
PICTURE MODE button
RECALL button
AUDIO MODE button
D
/
N
SURROUND button
CH I / II button
MULTI PICTURE (PinP) button
Buttons for MULTI PICTURE mode
RETURN button
SELECT / ADJUST buttons (
+
I
/
II
i
INPUT SELECT button
MENU button
2-4-12
A
/
B
MENU
P+
P-
PROGRAM UP / DOWN buttons
)
-
+
OK
VOLUME UP / DOWN buttons
DV D
OK button
MUTE button
FREEZE button
ZOOM button
FREEZE
ZOOM
DVD CONTROL buttons
1
2
5
3
6
9
PROGRAM SELECT buttons
4
7
8
0
PROGRAM UP / DOWN buttons
AV1
AV2
AV3
AV4
RGB / VIDEO buttons
RGB1
RGB2
TIME button
Loading Batteries
Handling the Remote Control
1. Open the battery cover.
• Slide back and remove the battery
cover in the direction of the arrow.
Use the remote control within about 5 m from front of the unit’s
remote-control sensor and within 30 degrees on both sides.
2. Load batteries.
• Load two Size AA batteries included
observing the correct polarities.
With in 30
With in 30
degrees
degrees
About 3m
About 3m
About 5m
D
/
N
i
+
I
/
II
A
/
B
2-4-12
MENU
P+
P-
-
+
OK
3. Close the battery cover.
• Replace the battery cover in the
direction of the arrow and snap it back
into place.
D
V
D
FREEZE
ZOOM
1
2
5
3
6
9
4
7
8
0
AV1
AV2
AV3
AV4
RGB1
RGB2
ATTENTION
• Do not drop or impact the remote control.
• Do not splash the remote control with water or put it on a wet
object to avoid possible failures.
• Before leaving the remote control out of use for an extended
period of time, remove the batteries from it.
• If the remote control begins to lack responsiveness, replace the
batteries.
• Strong light such as direct sunlight impinging on the
photoreceptor of the remote control can cause operational
failure. Position this unit to avoid direct contact with such light.
CAUTION
• Do not use new and old batteries together. The batteries could
explode or leak, resulting in fires, physical injury, or stains.
• When loading batteries, observe their correct polarities as marked
on the product. If loaded in the wrong direction, the batteries
could explode or leak, resulting in fires, physical injury, or stains.
43
COMPONENT NAMES (continued)
Remote control (provided for the optional tuner unit) (continued)
PICTURE MODE
AUDIO MODE
You may recall the picture mode by
pressing this button. Each time pressed,
picture mode is changed in following
sequence.
You may recall the sound mode by pressing
this button. Each time pressed, sound mode
is changed in following sequence.
Movie
Music
Dynamic
Natural
D / N
Favourite
Speech
MATRIX SURROUND
Press this button to set Matrix
Surround On or Off.
INPUT SELECT
Press this button to change input
mode.
+
i
I / II
MULTI PICTURE
Press this button to change the
screen to multi-pictures. Press it
again to return to normal picture.
RECALL
You can see the input mode status on
the screen by pressing this button.
2-4-12
A / B
MENU
P+
CH I/II
This button is for A2 / NICAM
models only.
-
+
OK
MULTI MODE
P-
In multi-picture mode, pressing this
button will change the multi-picture
mode.
DV D
MUTE
DVD CONTROL
You can use these buttons to operate
the selected brand of DVD player.
FREEZE
ZOOM
Press this button to turn off the set
sound. When press again or the _
volume up button will restore the sound.
FREEZE
1
2
5
3
6
9
Press this button to change the
picture to freeze mode. Press it again
to return to normal picture.
PROGRAM SELECT
Press these buttons to select a TV
program directly.
4
7
8
0
ZOOM
Press this button can change Picture size.
AV1
AV2
AV3
AV4
RGB1
RGB2
TIME
Pressing this button can indicate the
time by On-Screen display when
receiving a TV program on the screen
including TELETEXT service with the
time information.
44
[Buttons for TELETEXT Mode]
SUBTITLE button
TEXT button
D
/
N
+
I
/
II
i
TV button
COLOUR buttons
A
/
B
2-4-12
MENU
(RED, GREEN, YELLOW, BLUE)
P+
P-
-
+
OK
DV D
FREEZE
ZOOM
+
TEXT / TV TEXT button
1
2
5
3
6
9
MODE button
4
7
PAGE UP / DOWN button
SUB PAGE buttons
8
0
AV1
AV2
AV3
AV4
INDEX button
RGB1
RGB2
REVEAL button
HOLD button
TV / TEXT button
CANCEL button
U. N. L. button
TELETEXT FUNCTION
Buttons on Remote Control
Function
Press this to use the TELETEXT services.
TEXT
TV
Press this to return to the TV mode when in the TELETEXT mode.
This switches the receiver between the TV mode and the TELETEXT mode.
TV / TEXT
TEXT / TV + TEXT
MODE
In TELETEXT mode, this button switches between TV+TEXT screen (split) and TELETEXT only.
This selects the FASTEXT and FAVOURITE modes.
This selects the P100 page.
INDEX
This allows receiving of a sub page. When the button is pressed, “S✱✱✱✱” will be displayed at the top left of the screen.
SUB PAGE
SUB TITLE
Use this to access a subtitle service directly rather than through a TELETEXT service (subject to subtitle service broadcasting).
This allows the screen to return to the TV mode temporarily while searching for a required text page. When the required text
page has been received, the page number will be displayed at the top left of the screen. Press the CANCEL button again to
display the TELETEXT screen.
CANCEL
Each of these buttons selects a link page displayed at the lower part of the screen.
A FAVOURITE page can also be stored in the memory using one of the colours. It can then retrieve the page stored by
pressing the appropriate colour button.
RED
GREEN
YELLOW
BLUE
To store a FAVOURITE page :
• press the MODE button ;
• press a colour button for the FAVOURITE page ;
• enter the FAVOURITE page number to be stored and press the same colour button again to confirm.
Each time this button is pressed, the screen display mode changes through the following.
upper half screen enlarged
lower half screen enlarged
normal state
U. N. L
HOLD
This holds the page currently being displayed on the screen. Instead of the page number, a "
the screen. Press this button again to release the hold state.
" indicator appears at the top of
This allows hidden information (found on some teletext pages) to be displayed on the screen.
These buttons increase / decrease the TELETEXT page number.
REVEAL
PAGE UP / DOWN
NOTE
• Certain pages do not show linked pages at the bottom of the screen. To display linked pages, press the INDEX button.
45
INSTALLATION INSTRUCTIONS
Connecting Antenna
Make sure that the power switch of the monitor is turned off.
Speaker (R)
Speaker (L)
Monitor rear panel
antenna
20 18 16 14 12 10
8
6
4
2
21 19 17 15 13 11
9
7
5
3
1
Precautions when connecting the antenna
• Please use a coaxial cable which is free from interference to connect the antenna. Avoid using a parallel flat
feeder wire as interference may occur, causing reception to be unstable and stripe noise to appear on the
screen.
• Avoid using indoor antenna as this may be affected by interference. Please use CATV net or outdoor
antenna.
• Keep the power cord as far away from the antenna wire as possible.
If there are noise appearance in the picture of VHF-Low band channel, please use the double-shielded cable (not
provided) for RF LEADS to reduce the noise.
46
OPERATING INSTRUCTIONS
The functions of the buttons located on the bottom
of the monitor change as shown below:
D
/
N
POWER ON/OFF
button
+
I
/
II
i
INPUT SELECT
button
2-4-12
A
/
B
MENU
PROGRAM UP/DOWN
buttons
P+
P-
-
+
OK
VOLUME
DV D
UP/DOWN buttons
▼
▼
▼
FREEZE
ZOOM
▼
MUTE button
ZOOM button
MENU button
INPUT SELECT button
(OK button)
1
2
5
3
6
9
4
7
PROGRAM SELECT
buttons
PROGRAM UP/DOWN button
SELECT button)
8
0
(
VOLUME UP/DOWN
buttons
AV1
AV2
AV3
AV4
RGB/VIDEO
buttons
(
ADJUST buttons)
RGB1
RGB2
SUB-POWER button
• ( ) indicates the function while the MENU is displayed on the screen.
Input Switching
Size Switching
Each time the ZOOM button of the remote control is
pressed, the screen display size will change in sequence
and the status will be displayed at the bottom of the
screen.
•
Input can be switched by pressing the AV1, AV2, AV3,
AV4, RGB1 or RGB2 buttons of the remote control. And
the way to return to a TV channel is as follows:
• Pressing INPUT SELECT button at RGB2 input screen.
• Pressing some PROGRAM SELECT buttons and select a TV
channel.
• During TV mode
• Pressing PROGRAM UP/DOWN buttons at the screen without
OSD(On-screen display).
Auto
Full
Zoom
•
Input can be switched in the sequence of TV AV1
➔
➔
14:9Zoom
C14:9L
AV2 AV3 AV4 RGB1 RGB2 by pressing the
➔
➔
➔
➔
INPUT SELECT button of the monitor or the remote
• [Auto] is the mode using WSS (Wide Screen Signals) which
identify the picture format movies and programs are broadcast in.
Various broadcast stations now transmit WSS. It can be detected
and the monitor automatically switch to the correct format.
However, some broadcasters do not transmit WSS, so this
monitor will not recognize which format is being transmitted.
Therefore, Default Zoom setting in the Function Menu is used to
choose when a WSS has not been sent or has not been detected.
control.
TV
RGB2
AV1
AV2
RGB1
AV3
AV4
47
OPERATING INSTRUCTIONS (continued)
D
/
N
RECALL button
+
I
/
II
i
MULTI PICTURE
button
2-4-12
A
/
B
MENU
MULTI MODE
button
A/B button
SELECT buttons
P+
P-
-
+
OK
DV D
FREEZE
ZOOM
1
2
5
3
6
9
Displaying MULTI PICTURE
4
7
8
0
If the MULTI PICTURE button on the remote control is
pressed, multi pictures will display. And then three types
of the screen can be selected by pressing the MULTI
MODE button on the remote control.
PROGRAM UP/DOWN
buttons
AV1
AV2
AV3
AV4
RGB1
RGB2
The multi picture mode will change in the following
sequence each time the MULTI MODE button is pressed.
2 pictures (Split)
4 pictures
12 pictures
Activating the Split mode from the TV screen
Pressing the MULTI PICTURE button one time will display 2 pictures.
• The speaker icon can be shifted left and right by pressing the A/B button; the audio will be output from the
5
AV1
side on which the speaker icon is located.
• The same signal input cannot be selected for both screens at the same time.
• The TV channel can be changed by pressing the
control.
• The signal input mode of picture-A or picture-B (the one that the speaker icon is located on) can be selected
by pressing INPUT SELECT button on the remote control.
and
PROGRAM UP/DOWN buttons on the remote
A B
• Pressing the MULTI PICTURE button once again will cancel the multi picture mode.
•
•
When the Video input is set to RGB Video, multi picture mode is not possible.
Refer to the table for 2 pictures (Split) mode.
49
Activating the 4 pictures mode from the TV screen
Pressing the MULTI MODE button one time at the 2 pictures mode will display 4 pictures.
• Press [A/B] button to select picture A or picture B indicated by a red triangle. For pictures on right, press
B1
B2
8
6
AV1
green.
SELECT buttons to select picture. The selected channel number would change
• The TV channel can be changed by pressing the
and
PROGRAM UP/DOWN buttons on the remote
A
control.
B3 11
•
•
The audio can only be output from picture A in 4 pictures mode.
The same signal input mode cannot be selected for each screens at the same time.
• Pressing the MULTI PICTURE button at the 4 picture mode will cancel the multi picture mode. And then,
pressing the MULTI PICTURE button again will display the 4 pictures.
• Refer to the table for 4 pictures mode.
49
1
2
6
3
7
4
8
Activating the 12 pictures mode from the TV screen
Pressing the MULTI MODE button one time at the 4 pictures mode will display 12 pictures.
• Starting from channel 1, preset channels will automatically display in sequence on the 12 windows.
• This function activates only in TV mode.
5
9
10
11
12
• After several seconds, it refreshes the picture one by one.
• Pressing the MULTI PICTURE button at the 12 picture mode will cancel the multi picture mode. And then,
pressing the MULTI PICTURE button again will display the 12 pictures again.
• Pressing the MULTI MODE button at the 12 picture mode will display the 2 pictures (Split) mode.
NOTE
• Even if the input of the horizontal / vertical synchronizing signal (or video signal) stops in the multi picture display, the mode will not change to
power save mode.
• Please be careful since image retention will occur if display is left in a multi picture display state for a long period of time.
48
2 Pictures (Split)
Input terminal
AV1~AV4
PAL NTSC3.58 576i 480i
SECAM NTSC4.43 576p 480p
AV1, AV2
RGB1
RGB2
TELE
TEXT
Sub
1080i/50 1080i/60 720p/60 STB Component
Main
Main
Sub
PAL, SECAM
NTSC3.58/4.43
576i, 576p
480i, 480p
1080i/50
AV1
AV4
~
AV1
AV2
1080i/60
720p/60
RGB1
RGB2
STB
Component
: Available)
(
4 Pictures
Input terminal
AV1~AV4
PAL NTSC3.58 576i 480i
SECAM NTSC4.43 576p 480p
AV1, AV2
RGB1
RGB2
Main
TELE
TEXT
Sub
Sub 1
Sub 2
Sub 3
1080i/50 1080i/60 720p/60 STB Component
Main
PAL, SECAM
NTSC3.58/4.43
576i, 576p
480i, 480p
1080i/50
AV1
AV4
~
AV1
AV2
1080i/60
720p/60
RGB1
RGB2
STB
Component
: Available)
(
Input Signal Screen Display
The TV channel status can be displayed on the screen by
pressing the RECALL button of the remote control.
• The display will go out in approximately 6 seconds.
TV
TV position
Name
1
ABCDE
Sound mode
Off-timer
On-timer
-- -- Min.
-- -- : -- --
OFF
I
Sound system
49
OPERATING INSTRUCTIONS (continued)
D
/
N
+
I
/
II
i
2-4-12
A
/
B
MENU
P+
P-
-
+
OK
DV D
FREEZE
ZOOM
FREEZE button
1
2
5
3
6
9
4
7
8
0
AV1
AV2
AV3
AV4
RGB1
RGB2
Picture Freezing
[Split]
When the FREEZE button on the remote control is pressed, the screen transfers into the
freeze mode.
5
• There are two types of freezing screen mode, Split and Strobe. These are possible to select at the “Freeze
Mode” setting of the Function Menu.
• The Split mode will display 2 pictures from the same source on the screen with one active picture and the
other still.
A B
• The Strobe mode will display 12 pictures with the last picture active, while other 11 windows are still.
• Pressing the FREEZE button again changes the screen back to the normal picture.
• This function is also available from video input mode besides TV mode. Refer to the table for Freeze function
as below:
[Strobe]
1
2
6
3
7
4
8
Split
Strobe
PAL, SECAM
NTSC3.58/4.43
576i
5
9
10
11
12
Active
480i
576p
480p
1080i/50
1080i/60
720p/60
RGB, DVI-PC
: Available)
(
FUNCTION MENU
Refer to the page
. (It is same to the Picture Menu of Optional Video Unit Function)
37
But 1 item is added and 5 items are deleted.
Selected characters
Setup hint
This selects the display condition of the FREEZE mode between Split
(2 pictures) and Strobe (12 pictures).
Split
Strobe
Freeze Mode
Not Available (grayed out)
Mode Display
ID Number
Inverse
Not Available (grayed out)
Not Available (grayed out)
Not Available (grayed out)
Not Available (grayed out)
Standby White
Gamma
50
SETUP MENU
[During TV mode]
Picture
Setup
OK
Audio
Timer
Function
Setup
Language
Select
Auto Tuning
Manual Tuning
Fine Tuning
Sort
OK
MENU
Auto Off
Off
OK
Select
Set
Return
OK Set
Setup
Setup
Manual Tuning
Position
Search
Descrambler
Name
Sound System
Colour System
Skip
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Auto Off
Select
99
C22
Off
ABCDE
BG
OK
Off
OK
Set
Return
Auto
Off
Off
NR
Select
Return
Exit
Setup
Fine Tuning
Select
Prog.No.199
+56
Return
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Adjust
OK
Auto Off
Off
OK
Select
Set
Return
Setup
Sort
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Auto Off
Select
Position Name
C.S.MHz
100
101
102
103
104
105
106
107
ABCDE 471MHz
OK
BBC1
-----
C25
C40
C30
S27
BBC
Off
FGHIJ
OK
Set
Return
XYZAB S41
-----
-----
225MHz
C51
Select
Return
Exit
Setup
Setup
Setup
Auto Tuning
Country
Auto Tuning
Country
Auto Tuning
Country
Austria
Belgium
Croatia
Greece
Hungary
Iceland
Ireland
Portugal
San Marino
Spain
Czech Republic
Denmark
Finland
France
Germany
Sweden
Italy
Switzerland
Turkey
Netherlands
Norway
Poland
United Kingdom
Search
Select
Search
Select
Search
Select
OK
OK
OK
Set
Return
Set
Return
Set
Return
OK
Setup
Auto Tuning
Country
Setup
Auto Tuning
Portugal
San Marino
Spain
Scanning Channel Number: 33
OK
Sweden
Cancel
Switzerland
Turkey
United Kingdom
OK
Cancel
Search
Select
OK
Set
Return
51
OPERATING INSTRUCTIONS (continued)
SETUP MENU (continued)
Selected characters
Setup hint
Auto Tuning
▲
Select the country name by
SELECT buttons and press OK
▼
button.
(Page1)
–
(Page2)
(Page3)
–
• If some required stations could not be preset in this auto tuning
function, select and preset the required station in the required
position by the manual tuning operation.
Country
Search
Press the OK button and it starts the auto tuning.
Manual Tuning
▲
Set the position number. This also can be set by
UP/DOWN buttons.
PROGRAM
▼
••••••
1
2
3
199
AV00
–
Position
Search
At first, select the channel entry method, entering a two digit channel
number(CH), entering a two digit S-band number or entering a three
digit frequency(MHz), by pressing the OK button.
–
Enter two digit number by pressing 0~9 NUMBER buttons. If the
number is normal, then it starts the channel search.
–
–
–
–
–
–
(C--)
(S--)
Enter two digit number by pressing 0~9 NUMBER buttons. If the
number is normal, then it starts the channel search.
Enter three digit number by pressing 0~9 NUMBER buttons. If the
number is normal, then it starts the channel search.
(--MHz)
Set this to Off normally. If it is set to On, AV4 (Scart) terminal operates
as TV signal output, and the screen changes to display AV4 (Scart)
input signal automatically.
Off
(
On
Descrambler
Name
This is used to input the name of the TV station within 5 letters. After
▲
fixing the cursor on the first digit, select a letter by
SELECT
▼
buttons and move to next digit by
button again after finished.
ADJUST button. Press the OK
:a letter)
• Selectable letters are “0”~`”9”, ”A”~`”Z”, “+”, “–”, ” ”(blank),
”,”(comma) and ”.”(period) .
BG
I
DK
Select the sound system through the 5 different settings.
Select the colour system through the 5 different settings.
Sound System
Colour System
L'
L
Auto
PAL
SECAM
NTSC4.43
NTSC3.58
If this is set to On, that position will be skipped while selecting
positions by PROGRAM UP/DOWN buttons.
This is automatically set to On for those non-broadcasting channels.
Off
On
Skip
NR
If this is set to On, it helps to reduce the noise interference visible on
the screen, especially in the weaker signal reception areas.
Off
On
After completing the fine-tuning, press the RETURN button to exit this
mode.
• The variable range is -56 ~ +56.
Decreasing the frequency Increasing the frequency
Fine Tuning
data for the main tuner
data for the main tuner.
Sort
Press OK button at the a line that is required to change order, then
the characters will change to green. And move it up or down in the
–
–
(A Line of position List)
▲
list by pressing
SELECT buttons. And press OK button to
▼
complete it. Press the RETURN button to exit.
If this is set to On, the power will be turned off when there is no
transmission signal and no operation for about 10 minutes in the TV
mode.
Off
On
Auto Off
[During VIDEO signal input]
1 item is added to the Menu shown in the page
39
.
Selected characters
Setup hint
TV:AV4 (Scart) output will be fixed as TV signal output.
Monitor:AV4 (Scart) output can view the image as on the main unit.
But it is possible to monitor only the composite video signal from
AV1, AV2, or AV3 input that is displayed on the screen at the time.
• If Descrambler is set to On, it will be fixed as TV automatically.
TV
Monitor
Scart Output
52
OTHER FUNCTIONS
A2 / NICAM / Sound Multiplex
• The CH I / II button is only useful for NICAM and sound multiplex signals.
Otherwise pressing this button will have no effect.
8
BILINGUAL / DUAL sound broadcast
When bilingual program is received, sound mode display appears in yellow as shown on
NICAM [II]
right.
Press the CH I / II button to select the sound to be heard.
Each time the button is pressed, I, II or (force mono) appear cyclically on the screen.
▼
When receiving NICAM signals, NICAM display will appear as below.
Yellow
Green
Sound multiplex signal received
Yellow
[I]
[II]
Yellow
Yellow
Green
NICAM signal received
NICAM [II]
NICAM [I]
Select I, II or
(force mono) to hear the CH I, CH II or MONO broadcast respectively.
STEREO sound broadcast
When a stereo program is received, sound mode display will appear in red, and you can
press the CH I / II button to select between stereo and mono sound.
8
Each time the button is pressed,
or (force mono)appear cyclically on the screen.
▼
When receiving NICAM signals, NICAM display will appear as below.
Sound multiplex signal received
Red
Green
NICAM signal received
Green
Red
NICAM
Select
or (force mono) to hear the STEREO or MONO broadcast respectively.
Monaural sound broadcast
8
When a monaural program is received, sound mode display will appear in green.
You can press the CH I / II button to select the sound mode between monaural and forced
mono (sound is same).
Each time the button is pressed,
or (force mono) appear cyclically on the screen.
▼
NOTE
• If sound signal is not strong enough for quality reception, press the CH I / II button until appears on the screen to receive a clear mono sound.
▼
• If sound has hiss noise or keep switching between stereo and mono mode due to signal condition, press the CH I / II button until appears
▼
on the screen to receive a clear mono sound.
53
OPERATING INSTRUCTIONS (continued)
OTHER FUNCTIONS (continued)
DVD Player Selection
• You can use this remote control to operate the selected brand of DVD player by pressing the following buttons on the remote control
simultaneously.
Brands of DVD Player
Hitachi
Press
Brands of DVD Player
RCA
Press
RECALL
1
2
3
4
5
6
7
8
RECALL
RECALL
9
0
Pioneer
Mitsubishi
Onkyo
RECALL
RECALL
RECALL
RECALL
RECALL
RECALL
RECALL
Panasonic
Toshiba
RECALL
RECALL
INDEX
MODE
Zenith
Philips
Orion
RECALL SUB PAGE
JVC
Shinco
RECALL
RECALL
CANCEL
REVEAL
Samsung
Sony
Skyworth
Bubuko
RECALL
TV/TEXT
Example
1
To operate HITACHI DVD player, press and hold the RECALL button, followed by the
button.
D
/
N
+
I
/
II
i
A
/
B
2-4-12
MENU
P+
P-
RECALL button
MODE button
-
+
OK
DV D
FREEZE
ZOOM
1
2
5
3
6
9
4
7
8
0
SUB PAGE buttons
AV1
AV2
AV3
AV4
INDEX button
RGB1
RGB2
REVEAL button
TV / TEXT button
CANCEL button
NOTE
• Not all models of the listed brands can be operated using this remote control.
54
TROUBLESHOOTING
Symptoms That Seemingly Appear to be Failures
Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer.
WARNING
Customer servicing can be hazardous.
Symptom
Possible reason
Remedy
(1) Connection of antenna cable to the TV is (1) Make new connection and/or change antenna
poor.
plug.
(2) Corroded or poor antenna connections.
(3) Antenna has moved position.
(4) Adverse weather conditions.
(5) Transmitter problems.
(2) Make new connections or renew cable.
(3) Re-align antenna.
(4) None.
(5) Check with local Operator.
snowy picture - poor sound
(1) Antenna has moved position.
(2) TV not tuned correctly.
(3) Adverse weather conditions.
(4) Transmitter problems.
(1) Re-align antenna.
(2) Re-tune or fine tune TV.
(3) None.
(4) Check with local Operator.
(5) Check the external equipment connected.
(5) AV Input not set correctly.
multiple images - sound O.K
(1) Interference from electrical or mechanical (1) Check devices for shielding and renew if
motors, fluorescent lights, portable
radios etc.
necessary or move further from TV.
intermittent interference
(1) TV may be in AV mode.
(1) Press the INPUT SELECT button or
to
buttons
9
0
on your remote control to return to normal TV
mode.
(2) Picture/sound setting set to minimum.
(3) TV in standby or power save mode.
(2) Check picture / sound controls (go to MAIN
MENU).
(3) Press POWER ON / OFF button.
no picture or sound
55
PRODUCT SPECIFICATIONS
This table shows the specifications when the optional video unit and tuner unit have been inserted.
Display
dimensions
Approx. 32 inches (716 (H) x 399 (V) mm, diagonal 820mm)
852 (H) x 1024 (V) pixels
Approx. 42 inches (922 (H) x 522 (V) mm, diagonal 1059mm)
Panel
Resolution
1024 (H) x 1024 (V) pixels
Net dimensions
(excluding Speakers/Stand)
830 (W) x 506 (H) x 92 (D) mm
1030 (W) x 636 (H) x 91 (D) mm
Net weight
(excluding Speakers/Stand)
24.6kg
34.9kg
Temperature
Operating : 5˚C to 35˚C, Storage : 0˚C to 40˚C
Ambient
conditions
Relative humidity Operating : 20% to 80%, Storage : 20% to 90% (non-condensing)
Power supply
AC100 - 240V, 50/60Hz
Power consumption/at standby 255W / <3W
365W / <3W
Audio output
(RGB input)
12W + 12W (6Ω)
RGB1 DVI input terminal (DVI-D)
RGB1 audio input terminal (3.5mm Stereo Mini Jack)
RGB2 analog RGB input terminal (D-sub 15-pin)
RGB2 audio input terminal (3.5mm Stereo Mini Jack)
Input terminals
Input signals
0.7 V/1.0 Vp-p, analog RGB (Recommended Signal)
480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
Video signals
Sync signals
H/V separate, TTL level [2KΩ]
H/V composite, TTL level [2KΩ]
Sync on green, 0.3 Vp-p [75Ω]
42
29
46 modes
Recommended signal
(Video input)
AV1: composite video input terminal (RCA)
AV1: Y PB PR video input terminal (RCA)
AV1: L/R audio input terminal (RCA)
AV2: composite video input terminal (RCA)
AV2: Y/G PB/B PR/R video input terminal (RCA)
AV2: L/R audio input terminal (RCA)
Input terminals
AV3: composite video input terminal (RCA)
AV3: S video input terminal (RCA)
AV3: L/R audio input terminal (RCA)
AV4: composite video / S video / RGB / L/R audio input terminal (Scart)
Input signals
AV1: PAL, SECAM, NTSC3.58, NTSC4.43
AV1: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
AV2: PAL, SECAM, NTSC3.58, NTSC4.43
AV2: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60, RGB
AV3: PAL, SECAM, NTSC3.58, NTSC4.43
AV4: PAL, SECAM, NTSC3.58, NTSC4.43
AV4: RGB
Video signals
OUTPUT (MONITOR): composite video monitor-output terminal (RCA)
OUTPUT (MONITOR): L/R audio monitor- output terminal (RCA)
AV4: composite video / L/R audio output terminal (SCART)
Video output Signal
42
15 modes
Recommended signal
(RF input)
Input terminals
ANT : 75Ω Unbalanced
Input signals
PAL B, G, H / I / D, K
SECAM B, G / D, K / K1 / L, L'
RF Video System
• The monitor takes at least 30 minutes to attain the status of optimal picture quality.
56
Hitachi Plasma TV Horizontal Wall-mount Unit
Model
PWT001 Installation Instructions
Thank you for purchasing the Hitachi Plasma TV Wall-mount Unit.
To ensure correct usage, please read this instruction manual thoroughly. After reading, please store this
manual in a safe place for future reference.
This plasma TV wall-mount unit is for use with the following models:
HITACHI Plasma TV CL32-PD2100, CL37-PD2100, CL42-PD2100, 32PD5100, 42PD5100, 42PMA500
32PD5000, 32PD5200, 32PD5300, 37PD5200, 42PD5000, 42PD5200, 42PD5300, CMP4211/2, CMP4213/4
Special techniques are necessary for installation of the plasma TV.
I Do not attempt to perform this work by yourself.
I Request an installation specialist to install this unit.
I This company assumes absolutely no responsibility for injuries and damages that may occur due to
improper installation and handling.
I Please remember that if you remove the plasma TV set from the wall later, you will find the screw holes and
anchor bolts for the mounting unit left on the wall. Also note that a long use of the plasma TV set may
discolor the wall around it due to its heat and air flow.
To dealers and shops
G To ensure customer safety, be sure to design the installation location so that the strength is sufficient to
withstand the weight of both the plasma TV and the wall-mount unit.
G Always use at least two persons for all installations.
G Fully tighten all of the mounting screws as specified in the installation instructions.
Parts Configuration Chart
In the parts packing
Wall-mount metal
x
(top) 1
M5 - 6 flat washer
x
x
M6 18 screw
TV-mount metal
x
8
x
10
2
Wall-mount metal
x
(center) 1
Wire clamp
x
2
Parts for CL37-PD2100 only
x
M6 18 screw
Bracket (R),(L)
x
Wall-mount metal
x
(bottom) 1
x
4
1 each
Usage cautions to ensure correct usage
Symbols
GThe following symbols are used to ensure safe usage of the product, to prevent danger to yourself and other
parties and to prevent damage to property.
I This symbol indicates that incorrect handling due to ignoring this symbol
WARNING
can result in the possibility of personal injury or even death.
I This symbol indicates that incorrect handling due to ignoring this symbol
CAUTION
can result in the possibility of personal injury and physical damage.
IThis symbol indicates additional
cautions (including warnings).
Caution
(general)
IThis symbol indicates forbidden
actions.
Disassembly
prohibited
Forbidden
(general)
IThis symbol indicates required actions.
Indicates that the power plug is to be
disconnected from the power outlet.
Required
(general)
Safety Cautions
WARNING
I When a malfunction occurs, disconnect the power
plug from the power outlet and take measures to
prevent other people coming near the plasma TV.
In the cases such as
G
The plasma TV is loose and vibrates to an extreme degree,
Mounting screws or parts are loose or missing,
G
failure to take appropriate actions can result in injury.
Perform the following actions immediately whenever a
malfunction occurs.
Turn off the plasma TV power switch.
x
Disconnect the power plug from the power outlet.
➁
Surround the area with rope, etc., to prevent other people
coming near.
➂
Contact your local dealer.
➃
Disconnect the Contact your
power plug from local dealer.
the power outlet.
I Ask your dealer to install, move or adjust the angle
of the wall-mount unit.
Incorrect installation or adjustment can cause the plasma TV to fall.
Handling by other than
professional contractors
is prohibited.
– 2 –
Installation Location
WARNING
Plaster board or
thin ply wood, etc.
I The wall where the wall-mount unit is to be
installed must be capable of long-term
support of the total load of the plasma TV and
wall-mount unit. Measures should also be
taken to ensure sufficient strength to
withstand the force of earthquakes, vibration
and other external forces.
Incorrect installation can cause the plasma TV to fall and
cause injury.
Total load of the (plasma TV + wall-mount unit)
= 26kg CL32-PD2100
•••
Pillar or
thick ply wood.
34kg CL37-PD2100
•••
37kg CL42-PD2100
•••
G Installation on a wooden wall
Always install so that the load is supported by a pillar. If the
strength of the pillar is insufficient, add reinforcement. Do
not install on decorative posts or plaster board.
G Installation on a concrete wall
Use commercially available anchors that are capable of
fully supporting the load of the plasma TV.
CAUTION
I Avoid installing in
locations where the
I Do not block the
ventilation holes.
Also provide
10cm
or more
temperature and
humidity are
excessively high,
and where contact
with water is
possible.
These can result in fire
or electrical shock.
sufficient clearance
in regard to the
surroundings to
avoid blocking the
ventilation.
10cm
or more
10cm
or more
The internal
temperature could
elevate and possibly
result in fire.
I Do not install close
to an air-
I Install only on a
vertical surface.
Avoid sloped
conditioner intake
or outlet.
Do not install in
locations where there
is excessive amounts
of dust, oily smoke or
tobacco smoke.
surface. Also, do
not install facing
upward.
The internal
temperature could
elevate and possibly
result in fire.
Fire could result.
Injury or damage could
also result from falling.
– 3 –
CAUTION
I Do not install in
I Do not install where
there is direct
locations where
there is excessive
vibration or impact.
sunlight and other
strong light.
Injury and damage
could result from
falling.
Strong light could result
in eye fatigue during
usage.
Installing
WARNING
I Use the specified
bolts and screws in
the specified places
and tighten firmly.
I Make sure the TV-
mount metals and
wall-mount metals
are firmly engaged.
Failure to do this could
cause injury if the
plasma TV falls.
Failure to do so could
cause the plasma TV
to fall.
I Do not alter any of
the parts. And do
not use broken
parts.
I Always use at least
two people to
perform the
installation work.
This could result in
injury due to the
plasma TV falling.
Injury could result from
dropping heavy
objects.
I Use care to prevent
the fingers being
caught.
Installation Method
Assembling the wall-mount metals
Assemble the wall-mount metal (Top),
(Center) and (Bottom) with 4 M6 x 18
screws.
I
M6 x 18 screw x 4
cutout
Wall-mount metal
(top)
Wall-mount metal
(center)
Wall-mount metal
(bottom)
– 4 –
Mounting the wall-mount unit on the wall
1. Prepare at least four sets of commercially available anchors and screws, etc., for various types of walls.
2. Carefully read the safety cautions concerning installation locations as described in this instruction manual and
then select a suitable location for installation.
3. The relationship between the plasma TV exterior and center, and the positions of the wall-mount unit mounting
holes is shown in the diagram for the various models. Install the anchors in the wall as shown in the diagram and
process the holes as necessary.
G Make sure that the strengths of the wall and the screws are fully sufficient.
32 inch
37 inch
– 5 –
42 inch
4. Fasten the wall-mount unit securely to the wall.
G Clamp to two or more of the long slotted holes in
the upper and lower parts of each wall-mounting
metal in a well-balanced manner.
5. Dressing the cables
G When passing the plasma TV power cord and
signal cables behind the plasma TV, use wire
clamps, etc., to prevent cable damage.
cutout
Mount on a firm,
solid surface.
Wall-mount metal (top)
Wall-mount metal (bottom)
Wire clamps
Use the washers provided as necessary.
Mounting the TV-mount metals on the plasma TV
1. Remove the stand.
2. Installing the TV-mount metals
Place a protective sheet cover on the top of a
x
CL32-PD2100
table and place the plasma TV on the cover with
the back side upward.
Remove the 4 EMI ground screws.
(for CL32-PD2100 only.)
Remove the 4 or 5 (CL37-PD2100) screws
IFasten the two TV-mount metals to the back of the
x
plasma TV with 4 M6 18 screws.
➁
➂
fastening the stand and remove the stand in the
direction indicated by the arrow mark.
Remove the 4 screws
4 M6 x 18 screws
Remove the 4 EMI ground
screws.(CL32-PD2100)
TV-mount metal
The 3rd TV-mount
metal hole
Plasma TV
Table
Remove the screws
(CL37-PD2100)
The 4th TV-mount
metal hole
Protective sheet cover
Stand
– 6 –
CL37-PD2100
Fasten the bracket (R) , (L) to the TV mount metal
x
with 4 M6 18 screws.
Fasten the two TV-mount metals to the back of the
x
plasma TV with 4 M6 18 screws.
x
➁
TV-mount metal
4 M6 x 18 screws
4 M6 x 18 screws
Bracket
(R),(L)
Bracket
The 1st TV-mount
metal hole
CL42-PD2100
IFasten the two TV-mount metals to the back of the
x
plasma TV with 4 M6 18 screws.
The 2nd TV-mount
metal hole
The 5th TV-mount
metal hole
Installing the plasma TV on the wall mount
Hang the TV-mount metal catches on the wall-mount unit cutouts.
Fasten with 2 M6 x 18 screws from the bottom.
x
➁
➂
After make sure all mouting works are completely done, connect power cord and signal cables.
Cutout
Wall-mount unit
GThe plasma TV
should always be
carried by at least
two people.
GDisconnect the
plasma TV power
cord and all
Make sure that
the top cutouts
and catchs are
engaged.
cables.
Catch
2 M6 x 18 screws
TV-mount metal
– 7 –
Product Specifications
External Dimensions
Dimension (A),(B)
Model
A
B
CL32-PD2100
CL37-PD2100
CL42-PD2100
377
414
414
113
100
51
Mass
2.6kg
Main material Steel sheet
Surface treatment Black electrodeposited baked paint
Angle adjustment Vertical fix
Products mounted Hitachi Plasma TV CL32-PD2100 , CL37-PD2100 , CL42-PD2100
Thank You for purchasing this Hitachi Television.
In the unlikely event that this product should develop a fault, we undertake to repair
or replace any part of the product which fails due to a manufacturing defect within
12 months of the date of purchase provided that ...
1. the product has been installed and used only in accordance with the instructions
supplied with the product.
2. the product has not been repaired, maintained, or modified by any person other
than a Hitachi authorized dealer.
3. the product serial number has not been removed or altered.
•this guarantee does not apply to a product acquired second hand or for
commercial or communal use.
•this guarantee does not cover the replacement of exhausted batteries, the
adjustment of user controls, or aerial alignment.
•any parts replaced under this guarantee shall become the property of HITACHI
EUROPE LTD..
•please note that evidence of the date of purchase will be required before any
service under this guarantee is carried out.
Use the boxes provided below to record your TV’s Model and Serial Number - these are found
on the rating plate located on the rear of the Plasma screen and on the bottun of the AVC. Also,
record where and when you purchased this T.V. This information will help any future queries you
may have and should be used in all correspondence with Hitachi service centres.
MODEL
SERIAL NUMBER
DEALER/STORE
DATE PURCHASED
This guarantee does not affect your statutory rights.
In all cases of difficulty please
consult your Hitachi dealer.
Hitachi, Ltd. Tokyo, Japan
International Sales Division
THE HITACHI ATAGO BUILDING,
No. 15 –12 Nishi Shinbashi, 2 – Chome,
Minato – Ku, Tokyo 105-8430, Japan.
Tel: 03 35022111
HITACHI EUROPE LTD,
Whitebrook Park
Lower Cookham Road
Maidenhead
HITACHI EUROPE S.A.
364 Kifissias Ave. & 1, Delfon Str.
152 33 Chalandri
Athens
Berkshire
GREECE
SL6 8YA
Tel: 1-6837200
UNITED KINGDOM
Tel: 01628 643000
Fax: 01628 643400
Fax: 1-6835964
Email: [email protected]
HITACHI EUROPE GmbH
Munich Office
Dornacher Strasse 3
D-85622 Feldkirchen bei München
GERMANY
HITACHI EUROPE S.A.
Gran Via Carlos III, 86, planta 5
Edificios Trade - Torre Este
08028 Barcelona
SPAIN
Tel: +49-89-991 80-0
Tel: 93 409 2550
Fax: +49-89-991 80-224
Hotline: +49-180-551 25 51 (12ct/min)
Fax: 93 491 3513
Email: [email protected]
HITACHI EUROPE srl
Via Tommaso Gulli N.39, 20147
Milano, Italia
HITACHI Europe AB
Box 77 S-164 94 Kista
SWEDEN
ITALY
Tel: +39 02 487861
Tel: +39 02 38073415 Servizio Clienti
Fax: +39 02 48786381/2
Email: [email protected]
Tel: +46 (0) 8 562 711 00
Fax: +46 (0) 8 562 711 13
Email: [email protected]
HITACHI EUROPE S.A.S
Lyon Office
B.P. 45, 69671 BRON CEDEX
FRANCE
HITACHI EUROPE LTD (Norway) AB
STRANDVEIEN 18
1366 Lysaker
NORWAY
Tel: 04 72 14 29 70
Tel: 67 5190 30
Fax: 04 72 14 29 99
Fax: 67 5190 32
Email: [email protected]
Email: [email protected]
HITACH EUROPE AB
Egebækgård
Egebækvej 98
HITACHI EUROPE AB
Neopoli / Niemenkatu 73
FIN-15140 Lahti
DK-2850 Nærum
DENMARK
Tel: +45 43 43 6050
Fax: +45 43 60 51
Email: [email protected]
FINLAND
Tel : +358 3 8858 271
Fax: +358 3 8858 272
Email: [email protected]
Hitachi Europe Ltd
HITACHI EUROPE LTD
Na Sychrove 975/8
101 27 Pr aha 10 – Bohdalec
CZECH REPUBLIC
Bergensesteenweg 421
1600 Sint-Pieters-Leeuw
BELGIUM
Tel: +32 2 363 99 01
Fax: +32 2 363 99 00
Email: [email protected]
Tel: +420 267 212 383
Fax: +420 267 212 385
Email: [email protected]
|