HP Hewlett Packard Hewlett Packard Computer Monitor W17E User Manual

Back to Contents Page  
w17e/W17q LCD Monitor  
Users Guide  
The only warranties for HP products and services are set forth in the express warranty statements accompanying such  
products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for  
technical or editorial errors or omissions contained herein.  
HP assumes no responsibility for the use or reliability of its software on equipment that is not furnished by HP.  
This document contains proprietary information that is protected by copyright. No part of this document may be photocopied,  
reproduced, or translated to another language without the prior written consent of HP.  
Hewlett-Packard Company  
P.O. Box 4010  
Cupertino, CA 95015-4010  
USA  
Copyright © 2007 Hewlett-Packard Development Company, L.P.  
Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation.  
Adobe and Acrobat are trademarks of Adobe Systems Incorporated.  
Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license.  
HP supports lawful use of technology and does not endorse or encourage the use of its products for purposes other than those  
permitted by copyright law.  
The information in this document is subject to change without notice.  
Part number: 446747-002  
 
Safety and Maintenance Guidelines  
Important Safety Information  
The power cord is designed for use with your monitor. To use a different cord, use only a power source and  
connection compatible with this monitor. For information on the correct power cord set to use with your monitor,  
WARNING: To reduce the risk of electric shock or damage to your equipment, do not disable  
the power cord grounding feature. The grounding plug is an important safety feature. Connect  
the equipment to a grounded (earthed) power outlet.  
WARNING: For your safety, be sure that the grounded power outlet you plug the power cord  
into is easily accessible to the operator and located as close to the equipment as possible. To  
disconnect power from the equipment, unplug the power cord from the power outlet by  
grasping the plug firmly. Never pull on the cord.  
CAUTION: To protect your monitor, as well as your computer, connect all power cords for your  
computer and its peripheral devices (such as a monitor, printer, or scanner) to a surge  
protection device such as a power strip with surge protection or uninterruptible power  
supply (UPS).  
Not all power strips provide surge protection; the power strips must be specifically labeled as  
having this ability. Use a power strip whose manufacturer offers a damage replacement policy  
so you can replace your equipment if surge protection fails.  
Safety Precautions  
CAUTION: Avoid applying pressure to the LCD screen; doing so can cause damage.  
Use only a power source and connection compatible with this monitor, as indicated on the label/back plate of  
the monitor.  
Be sure the total ampere rating of the products connected to the outlet does not exceed the current rating of the  
electrical outlet, and the total ampere rating of the products connected to the cord does not exceed the rating  
of the cord. Look on the power label to determine the ampere rating (Amps or A) for each device.  
Install your monitor near an outlet that you can easily reach. Disconnect the monitor by grasping the plug  
firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord.  
Do not allow anything to rest on the power cord. Do not walk on the cord.  
     
Maintenance Guidelines  
To enhance the performance and extend the life of your monitor:  
Do not open your monitor cabinet or attempt to service this product yourself. If your monitor is not operating  
properly or has been dropped or damaged, contact your Hewlett-Packard authorized dealer, reseller, or  
service provider.  
Adjust only those controls that are described in the operating instructions.  
Turn your monitor off when not in use. You can substantially increase the life expectancy of your monitor by  
using a screen saver and turning off the monitor when not in use.  
Keep your monitor in a well-ventilated area, away from excessive light, heat, or moisture.  
Slots and openings in the cabinet are provided for ventilation. These openings must not be blocked or  
covered. Never push objects of any kind into cabinet slots or other openings.  
Unplug your monitor from the wall outlet before cleaning.  
Do not drop your monitor or place it on an unstable surface.  
When removing the monitor pedestal base, you must lay the monitor face down on a soft area to prevent it  
from getting scratched, defaced, or broken.  
Cleaning the Monitor  
The monitor is a high-quality optical device that requires special care when cleaning. To clean the monitor, follow  
these steps:  
1 Turn off the computer and the monitor.  
2 Unplug your monitor from the wall outlet before cleaning.  
CAUTION: Do not use benzene, thinner, ammonia, or any volatile substances to clean the  
monitor screen or cabinet. These chemicals may damage the monitor. Do not use liquid  
cleaners or aerosol cleaners. Never use water to clean an LCD screen.  
3 Wipe the screen with a dry, soft, clean cloth.  
If the screen requires additional cleaning, use an antistatic screen cleaner.  
4 Dust the monitor housing. Use a damp cloth to clean the cabinet.  
If the cabinet requires additional cleaning, use a clean cloth dampened with isopropyl alcohol.  
5 Plug in the monitor.  
6 Turn on the monitor and the computer.  
   
Setup  
Base and Tilt  
Attaching the Base  
1 Set the panel face-down on a flat, protected surface.  
2 Align the pedestal slots with the panel tabs and insert (A).  
3 Slide the pedestal to the right to lock it into place (B).  
4 Lift the panel and lower the pedestal onto the base until the push tab locks.  
WARNING: Be careful to avoid pinching or scraping fingers when attaching the base.  
CAUTION: To prevent damage, avoid applying pressure to the panel front.  
     
Removing the Base  
1 Push the release tab and raise the pedestal off the base.  
2 Set the panel face-down on a flat, protected surface.  
3 Slide the pedestal to the left to unlock it from the base (A).  
4 Remove the pedestal from the panel (B).  
WARNING: Be careful to avoid pinching or scraping fingers when attaching the base.  
CAUTION: To prevent damage, avoid applying pressure to the panel front.  
 
Adjusting the Tilt  
For optimal viewing, adjust the screen tilt to your own preference, as follows:  
1 Face the front of the monitor and hold the stand so that you do not topple the monitor while changing the tilt.  
2 Adjust the tilt by moving the monitor’s top edge toward or away from you.  
CAUTION: To avoid breakage or other damage, do not touch the LCD screen while changing  
the tilt.  
 
Cables  
Attaching the Cables  
Attach the provided VGA cable to this monitor. Connectors are on the back of the monitor.  
1 Turn off your computer.  
2 Connect the built-in monitor speakers to the computer, using the audio cable (green connector).  
   
3 Connect one end of the 15-pin D-Sub VGA cable (blue connector) to the back of the monitor and connect the  
other end to the computer VGA port.  
4 Connect one end of the power cord to the back of the monitor and plug the other end into a grounded outlet.  
5 Turn on your monitor and computer.  
If your monitor displays an image, installation is complete. If it does not display an image, see Technical Support  
Wall Mounting Arm  
Preparing to Install a Wall Mounting Arm (Not supplied)  
This monitor can be attached to a wall mounting arm that you purchase separately.  
CAUTION: Before disassembling the monitor, turn off the monitor power, and disconnect all  
power, video, and audio cables.  
1 Disconnect the cables from the monitor.  
2 With the panel face-down on a protected surface, remove the screws and the pedestal attachment.  
3 Follow the manufacturer’s instructions to assemble the wall mounting arm.  
See Installing a Wall Mounting Arm for further installation instructions.  
Installing a Wall Mounting Arm  
1 Set the monitor screen down on a flat, soft, protected surface.  
2 Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the mounting holes  
in the back of the monitor.  
3 Insert four screws into the mounting holes and tighten.  
4 Reconnect the cables. Refer to the user’s manual that came with the wall mounting arm (purchased separately)  
for instructions on attaching it to the wall.  
     
Using the Monitor  
Operating Instructions  
Control buttons are located on the front of the panel, as shown in the illustration following. Use the Menu button  
to adjust the display settings to your personal preferences:  
Set up the monitor, attach the cables, and adjust the tilt as described in the Setup section above.  
Press the power button to turn the monitor on and off. The power indicator lights up when the monitor is on.  
The monitor must be turned on for the other control buttons to work.  
   
External Controls  
A Auto-configuration / Exit  
B
C
Volume decrease / Left navigation  
Volume increase / Right navigation  
D Menu / Enter  
E
F
Power  
LED indicator  
LED Indicators  
Status  
LED Color  
Green  
Full Power Mode  
Power Save Mode  
Amber  
See Technical Support FAQs for more information.  
   
Settings  
Setting the Optimal Resolution  
The recommended resolution for this monitor is 1440 by 900. To configure the monitor to this resolution,  
complete the setup procedure and make sure that the monitor is connected to the computer. Turn the monitor on  
and do the following:  
1 Click the Windows Start Button , and then click Control Panel.  
2 Under Appearance and Personalization, click Adjust Screen Resolution.  
3 Set the resolution slide bar to 1440 by 900.  
Monitor for instructions.  
Adjusting the Volume  
Press the front monitor panel volume increase and decrease buttons to adjust volume to the desired level. Volume  
can range from 0 (mute) to 100. The preset value is 50. Volume cannot be adjusted through the OSD menu.  
Locking the OSD  
To lock the OSD (onscreen display), press and hold the Menu button while the monitor is off, then press the  
power button to turn the monitor on. To unlock the OSD, repeat the locking procedure. When the OSD is locked,  
settings cannot be changed in the OSD menu.  
       
Adjusting OSD Settings  
1 Press the Menu button to activate the OSD menu.  
2 Press + or on the monitor front panel to navigate through the functions. Once the desired function is  
highlighted, press the Menu button again to activate it. If the selected function has a sub-menu, it will be  
displayed. Press + or again to navigate through the sub-menu functions. Once the desired sub-function is  
highlighted, press the Menu button to activate it.  
3 Press + or to change the settings of the selected function.  
4 To exit and save, select the Exit function. If you want to adjust another function, repeat steps 2–3.  
OSD Menu  
The figure below shows the OSD menu that appears when you first press the Menu button. In this figure, the  
Luminance icon has been selected, so it is highlighted and its title is displayed. Pressing Menu again will display  
the sub-menu for this function.  
Main Menu and Sub-Menu Items for Adjusting the OSD  
Main Menu  
Icon  
Sub-Menu  
Icon  
Main Menu Item  
Sub-Menu Item  
Description  
Luminance  
Contrast  
Contrast from digital-register  
Brightness  
Focus  
Backlight adjustment  
Image Setup  
Adjust picture phase to reduce  
horizontal-line noise  
Clock  
Adjust picture clock to reduce vertical-line  
noise  
   
Main Menu  
Icon  
Sub-Menu  
Icon  
Main Menu Item  
Sub-Menu Item  
Description (continued)  
Image Position  
H. Position  
Adjust the horizontal position of the  
picture  
V. Position  
Adjust the vertical position of the picture  
Color Temp.  
Warm  
Cool  
N/A  
N/A  
N/A  
Recall warm color temperature from  
EEPROM  
Recall cool color temperature from  
EEPROM  
sRGB  
Recall sRGB temperature from EEPROM  
Red gain from digital-register  
User / Red  
User / Green  
User / Blue  
Green gain from digital-register  
Blue gain from digital-register  
Auto-adjustment  
OSD Setup  
Automatically adjust the screen display for  
optimal viewing  
H. Position  
V. Position  
OSD Timeout  
Language  
Adjust the horizontal position of the OSD  
Adjust the vertical position of the OSD  
Adjust the OSD timeout  
Language  
Information  
Reset  
N/A  
N/A  
Select the language you like  
Information  
Show the resolution, H/V frequency and  
input port of current input timing  
Yes  
No  
N/A  
N/A  
Clear each old status of auto-configuration  
Do not execute reset, return to main menu  
Exit  
N/A  
N/A  
Exit OSD  
See Specifications for the horizontal and vertical scan ranges addressable by this monitor.  
Installing Drivers and Using the Auto-Adjustment Feature  
Downloading Drivers and Software  
To download the latest version of drivers and software files from the HP Support Web site:  
2 Select your country/region.  
3 Select Download Drivers and Software.  
4 Enter the model number of your monitor. The software download pages for your monitor will be displayed.  
5 Download and install the driver and software files using the instructions in the download pages.  
Using the Auto-Adjustment Function  
Press the Auto button to optimize the screen performance for VGA (analog). You can also access the  
Auto-adjustment feature through the OSD menu.  
Auto-adjustment can correct the following image quality conditions:  
Fuzzy or unclear focus  
Ghosting, streaking, or shadowing effects  
Faint vertical bars  
Thin, horizontal scrolling lines  
An off-center picture  
     
Technical Support FAQs  
Technical Support FAQs (Frequently Asked Questions)  
Problem & Question  
Possible Solutions  
Power LED is not on  
Make sure the Power button is on and the power cord is properly  
connected to a grounded power outlet and to the monitor.  
No Plug & Play  
In order for the Plug & Play feature of the monitor to work, you  
need a Plug & Play compatible computer and video card. Check  
with your computer manufacturer.  
Check the monitor’s video cable and make sure none of the pins  
are bent.  
Make sure the HP monitor drivers are installed (HP monitor drivers  
are available at: http://www.hp.com/support).  
Picture is fuzzy and has ghosting  
shadowing problem  
Adjust the contrast and brightness controls.  
Make sure you are not using an extension cable or switch box.  
We recommend plugging the monitor directly into the video card  
output connector on the back of your computer.  
Adjust the Image Setup feature in the OSD main menu.  
The Auto-adjustment function may fix this problem.  
Picture bounces, flickers or wave  
pattern is present in the picture  
Move electrical devices that may cause electrical interference as  
far away from the monitor as possible.  
Use the maximum refresh rate your monitor is capable of at the  
resolution you are using.  
Monitor is stuck in “Active Off-Mode”  
The computer power switch should be in the on position.  
The computer video card should be snugly seated in its slot.  
Make sure the monitor’s video cable is properly connected to the  
computer.  
Inspect the monitor’s video cable and make sure none of the pins  
are bent.  
Make sure your computer is operational by hitting the Caps Lock  
key on the keyboard while observing the Caps Lock LED. The LED  
should either turn on or off after hitting the Caps Lock key.  
   
Problem & Question  
Possible Solutions (continued)  
Missing one of the primary colors (red, Inspect the monitor’s video cable and make sure that none of the  
green, or blue)  
pins are bent.  
Make sure the monitor’s video cable is properly connected to the  
computer.  
Screen image is not centered or sized  
properly  
Adjust horizontal and vertical screen position.  
The auto-adjustment function may fix this problem.  
Picture has color defects (white does  
not look white)  
Adjust RGB color or select color temperature.  
Unable to set the monitor to the optimal Make sure that the graphics card supports the optimal  
resolution  
resolution (1440 x 900).  
Make sure that the latest supported driver is installed for the  
graphics card. For HP and Compaq systems, you can download  
the latest graphics driver for your system from:  
For other systems, refer to the Web site for your graphics card.  
Specifications  
All specifications represent the typical specifications provided by HP’s component manufacturers; actual  
performance may vary either higher or lower.  
General  
Model number  
w17e / W17q  
LCD Panel (17")  
Driving system  
Size  
TFT Active Matrix Color LCD  
431.8 mm (17" diagonal)  
R, G, B Analog Interface  
H/V TTL & TMDS  
Video  
Separate sync.  
Display color  
Dot clock  
262,000 colors  
135 MHz maximum  
Pixel Pitch  
0.255 mm (H) x 0.255 mm (V)  
Antiglare polarizer with hard coating  
140° (H), 130° (V)  
Face treatment  
Viewable angle  
Resolution  
Horizontal scan range  
30 kHz to 83 kHz  
367.2 mm  
Horizontal scan size (Maximum)  
Vertical scan range  
55 Hz to 75 Hz  
229.5 mm  
Vertical scan size (Maximum)  
Optimal preset resolution  
Highest preset resolution  
Highest addressable resolution  
Plug & Play  
1440 x 900 at 60 Hz  
1440 x 900 at 75 Hz  
1440 x 900 at 75 Hz  
VESA DDC2B  
Input Connectors  
D-Sub VGA 15-pin and audio jack  
Analog: 0.7Vp-p (standard), 75 OHM  
100~240V, 47~63 Hz  
Input Video Signal  
Power Source  
       
Preset Display Modes  
Standard  
Dos-mode  
VGA  
Resolution  
Horizontal Frequency (kHz)  
Vertical Frequency (Hz)  
720 x 400  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
832 x 624  
1024 x 768  
1024 x 768  
1024 x 768  
1152 x 864  
1440 x 900  
1440 x 900  
31  
31  
35  
38  
38  
35  
38  
48  
47  
50  
48  
56  
60  
68  
56  
71  
70  
60  
67  
73  
75  
56  
60  
72  
75  
75  
60  
70  
75  
75  
60  
75  
VGA  
VGA  
VGA  
SVGA  
SVGA  
SVGA  
SVGA  
SVGA  
XGA  
XGA  
XGA  
SXGA  
WXGA  
WXGA  
Physical Characteristics  
Connector Types  
Signal Cable Type  
Dimensions & Weight:  
Height (with base)  
Width  
15-pin Mini D-Sub VGA  
Detachable  
13.1 inches (332.4 mm)  
15.8 inches (400.4 mm)  
8.3 inches (211 mm)  
7.17 lb (3.25 Kg)  
Depth  
Weight (monitor only)  
Weight (with packaging)  
10.67 lb (4.84 Kg)  
Environmental  
Temperature:  
Operating  
5°C to +35°C  
Non-Operating  
Humidity:  
Operating  
–20°C to +60°C  
20% to 80% (non-condensing)  
5% to 90% (non-condensing)  
Non-Operating  
Altitude:  
Operating  
0~3,658 m (0~12,000 ft)  
0~12,192 m (0~40,000 ft)  
Non-Operating  
     
Power Cord Set Requirements  
The monitor power supply is provided with automatic line switching (ALS). This feature allows the monitor to  
operate on input voltages in the range of 100–240V, 50/60 Hz, 1.5A.  
The power cord set (flexible cord or wall plug) received with the monitor meets the requirements for use in the  
country/region where the equipment was purchased.  
If you need to obtain a power cord for a different country/region, you should purchase a power cord that is  
approved for use in that country/region.  
The power cord must be rated for the product and for the voltage and current marked on the product’s electrical  
ratings label. The voltage and current rating of the cord should be greater than the voltage and current rating  
marked on the product. In addition, the cross-sectional area of the wire must be a minimum of 0.75 mm²  
(0.03 in2) or 18AWG, and the length of the cord must be between 1.5 m (4.94 ft) and 3.6 m (12 ft). If you have  
questions about the type of power cord to use, contact your HP-authorized service provider.  
A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or  
against it. Particular attention should be paid to the plug, electrical outlet, and the point where the cord exits from  
the product.  
VGA Connector Pin Assignments  
15-Pin Side of  
Pin Number  
the Signal Cable  
Video-Red  
Video-Green  
Video-Blue  
Ground  
1
2
3
4
5
Detect Cable  
GND-R  
6
7
GND-G  
8
GND-B  
9
+5V  
10  
11  
12  
13  
14  
15  
Ground  
Ground  
DDC-Serial data  
H-sync  
V-sync  
DDC-Serial clock  
   
Plug and Play DDC2B Feature  
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the  
monitor to inform the host system of its identity and, depending on the level of DDC used, communicate  
additional information about its display capabilities.  
The DDC2B is a bi-directional data channel based on the I²C protocol. The host can request EDID information  
over the DDC2B channel.  
LCD Monitor Quality and Pixel Policy  
The HP LCD Monitor uses high-precision technology, manufactured according to high standards, to help  
guarantee trouble-free performance. Nevertheless, the display may have cosmetic imperfections that appear as  
small bright or dark spots. This is common to all LCD displays used in products supplied by all vendors and is not  
specific to the HP LCD Monitor. These imperfections are caused by one or more defective pixels or subpixels.  
A pixel consists of one red, one green, and one blue subpixel.  
A defective whole pixel is always turned on (a bright spot on a dark background), or it is always off (a dark  
spot on a bright background). The first is the more visible of the two.  
A defective subpixel (dot defect) is less visible than a defective whole pixel and is small and only visible on a  
specific background.  
To locate defective pixels, the monitor should be viewed under normal operating conditions and in normal  
operating mode at a supported resolution and response rate, from a distance of approximately 50 cm (16 in).  
We expect that, over time, the industry will continue to improve its ability to produce displays with fewer  
cosmetic imperfections, and we will adjust guidelines as improvements are made.  
For more information about your w17e / W17q LCD Monitor, refer to the HP Web site at:  
   
Agency Regulatory Notices  
Federal Communications Commission Notice  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to  
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference  
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio or television technician for help.  
Modifications  
The FCC requires the user to be notified that any changes or modifications made to this device that are not  
expressly approved by Hewlett-Packard Company may void the user’s authority to operate the equipment.  
Cables  
Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain  
compliance with FCC rules and regulations.  
       
Declaration of Conformity for Products Marked with FCC Logo,  
United States Only  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this  
device may not cause harmful interference, and (2) this device must accept any interference received, including  
interference that may cause undesired operation.  
For questions regarding your product, contact:  
Hewlett-Packard Company  
P. O. Box 692000, Mail Stop 530113  
Houston, Texas 77269-2000  
Or  
call: 1-(800)-474-6836  
For questions regarding this FCC declaration, contact:  
Hewlett-Packard Company  
P. O. Box 692000, Mail Stop 510101  
Houston, Texas 77269-2000  
Or  
call: 1-(281)-514-3333  
To identify this product, refer to the part, series, or model number found on the product.  
Canadian Notice  
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment  
Regulations.  
Avis Canadien  
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du  
Canada.  
European Union Regulatory Notice  
This product complies with the following EU directives:  
Low Voltage Directive 2006/95/EC  
EMC Directive 89/336/EEC  
Compliance with these directives implies conformity to applicable harmonized European standards (European  
Norms) which are listed on the EU Declaration of Conformity issued by Hewlett-Packard for this product or  
product family.  
This compliance is indicated by the following conformity marking placed on the product:  
xxxx*  
This marking is valid for non-Telecom products and EU  
harmonized Telecom products (e.g., Bluetooth).  
This marking is valid for EU non-harmonized Telecom  
products. *Notified body number (used only if  
applicable — refer to the product label).  
Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, Germany  
       
Disposal of Waste Equipment by Users in Private Households in the  
European Union  
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other  
household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a  
designated collection point for the recycling of waste electrical and electronic equipment. The separate collection  
and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure  
that it is recycled in a manner that protects human health and the environment. For more information about where  
you can drop off your waste equipment for recycling, please contact your local city office, your household waste  
disposal service or the shop where you purchased the product.  
Japanese Notice  
Japanese Power Cord Notice  
     
Japanese Material Content Declaration  
A Japanese regulatory requirement, defined by Specification JIS C 0950, 2005,  
mandates that manufacturers provide Material Content Declarations for certain  
categories of electronic products offered for sale after July 1, 2006. To view the  
JIS C 0950 material declaration for this product, visit www.hp.com/go/jisc0950  
Korean Notice  
Materials Disposal  
This HP product contains Mercury in the fluorescent lamp in the display LCD that might require special handling  
at end-of-life.  
Disposal of this material can be regulated because of environmental considerations. For disposal or recycling  
information, please contact your local authorities or the Electronic Industries Alliance (EIA) (www.eiae.org).  
HP Recycling Program  
HP offers product end-of-life return programs for HP and other manufacturers’ hardware in several  
geographic areas.  
The terms and availability of these programs vary by geography because of differences in regulatory  
requirements and local customer demand. For information on the HP recycling program, refer to the HP Web site  
       
EPA ENERGY STAR® Compliance  
Products marked with the ENERGY STAR® logo on the packaging box qualify with the U.S. Environmental  
Protection Agency’s ENERGY STAR® guidelines for energy efficiency.  
Products with the ENERGY STAR® label are designed to use less energy, help you save money on utility bills, and  
help protect the environment.  
ENERGY STAR® is a registered trademark owned by the U.S. government.  
 

HP Hewlett Packard HP Ultra Slim LED LCD Monitor LV2011 User Manual
HP Hewlett Packard Hewlett Packard Computer Monitor S2321A User Manual
Hanns G Computer Monitor HW216 User Manual
Electrolux Air O Convect AOS62ECM1 User Manual
Eizo RadiForce RX320 User Manual
Directed Electronics OHD1502 User Manual
Dell ST2320L User Manual
Compaq P 700 User Manual
Casio CS 53P User Manual
Black Box Computer Hardware LMC5027C R3 User Manual