Cypress CY7C1176V18 User Manual

CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
18-Mbit QDR™-II+ SRAM 4-Word Burst  
Architecture (2.5 Cycle Read Latency)  
Features  
Functional Description  
Separate independent read and write data ports  
Supports concurrent transactions  
The CY7C1161V18, CY7C1176V18, CY7C1163V18, and  
CY7C1165V18 are 1.8V Synchronous Pipelined SRAMs  
equipped with QDR™-II+ architecture. QDR-II+ architecture  
consists of two separate ports to access the memory array. The  
read port has dedicated data outputs to support read operations  
and the write port has dedicated data inputs to support write  
300 MHz to 400 MHz clock for high bandwidth  
4-word burst to reduce address bus frequency  
DoubleDataRate(DDR)interfacesonbothreadandwriteports  
(data transferred at 800 MHz) at 400 MHz  
operations. QDR-II+ architecture has separate data inputs and  
data outputs to completely eliminate the need to turn around the  
data bus that is required with common IO devices. Each port can  
be accessed through a common address bus. Addresses for  
read and write addresses are latched onto alternate rising edges  
of the input (K) clock. Accesses to the QDR-II+ read and write  
ports are completely independent of one another. In order to  
maximize data throughput, both read and write ports are  
equipped with Double Data Rate (DDR) interfaces. Each  
address location is associated with four 8-bit words  
(CY7C1161V18), 9-bit words (CY7C1176V18), 18-bit words  
(CY7C1163V18), or 36-bit words (CY7C1165V18) that burst  
sequentially into or out of the device. Because data can be trans-  
ferred into and out of the device on every rising edge of both input  
clocks K and K, memory bandwidth is maximized while simpli-  
fying system design by eliminating bus turnarounds.  
Read latency of 2.5 clock cycles  
Two input clocks (K and K) for precise DDR timing  
SRAM uses rising edges only  
Echo clocks (CQ and CQ) simplify data capture in high speed  
systems  
Single multiplexed address input bus latches address inputs  
for both read and write ports  
Separate port selects for depth expansion  
Data valid pin (QVLD) to indicate valid data on the output  
Synchronous internally self-timed writes  
Available in x8, x9, x18, and x36 configurations  
Depth expansion is accomplished with port selects for each port.  
Port selects allow each port to operate independently.  
Full data coherency providing most current data  
All synchronous inputs pass through input registers controlled by  
the K or K input clocks. All data outputs pass through output  
registers controlled by the or K or K input clocks. Writes are  
conducted with on-chip synchronous self-timed write circuitry.  
Core V = 1.8V ± 0.1V; IO V  
= 1.4V to V  
DD  
DD  
DDQ  
Available in 165-ball FBGA package (13 x 15 x 1.4 mm)  
Offered in both Pb-free and non Pb-free packages  
Variable drive HSTL output buffers  
JTAG 1149.1 compatible test access port  
Delay Lock Loop (DLL) for accurate data placement  
Configurations  
With cycle read latency of 2.5 cycles:  
CY7C1161V18 – 2M x 8  
CY7C1176V18 – 2M x 9  
CY7C1163V18 – 1M x 18  
CY7C1165V18 – 512K x 36  
Selection Guide  
Description  
400 MHz  
400  
375 MHz  
375  
333 MHz  
333  
300 MHz  
300  
Unit  
MHz  
mA  
Maximum Operating Frequency  
Maximum Operating Current  
1080  
1020  
920  
850  
Note  
1. The QDR consortium specification for V  
is 1.5V + 0.1V. The Cypress QDR devices exceed the QDR consortium specification and are capable of supporting V  
DDQ  
DDQ  
= 1.4V to V  
.
DD  
Cypress Semiconductor Corporation  
Document Number: 001-06582 Rev. *D  
198 Champion Court  
San Jose, CA 95134-1709  
408-943-2600  
Revised March 06, 2008  
 
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Logic Block Diagram (CY7C1163V18)  
D
[17:0]  
18  
Write Write Write Write  
Address  
Register  
A
(17:0)  
Reg  
Reg  
Reg  
Reg  
18  
Address  
Register  
A
(17:0)  
18  
RPS  
K
K
Control  
Logic  
CLK  
Gen.  
DOFF  
Read Data Reg.  
72  
CQ  
CQ  
36  
V
REF  
Reg.  
Reg.  
Reg.  
WPS  
BWS  
Control  
Logic  
Q
[17:0]  
36  
[1:0]  
18  
18  
QVLD  
Logic Block Diagram (CY7C1165V18)  
D
[35:0]  
36  
Write Write Write Write  
Address  
Register  
A
(16:0)  
Reg  
Reg Reg  
Reg  
17  
Address  
Register  
A
(16:0)  
17  
RPS  
K
K
Control  
Logic  
CLK  
Gen.  
DOFF  
Read Data Reg.  
144  
CQ  
CQ  
72  
V
REF  
Reg.  
Reg.  
Reg.  
WPS  
BWS  
Control  
Logic  
Q
[35:0]  
72  
[3:0]  
36  
36  
QVLD  
Document Number: 001-06582 Rev. *D  
Page 3 of 29  
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Pin Configurations  
165-Ball FBGA (13 x 15 x 1.4 mm) Pinout  
CY7C1161V18 (2M x 8)  
1
2
3
6
9
10  
11  
5
7
8
4
NC/72M  
A
K
NC/144M  
A
NC/36M  
CQ  
A
CQ  
WPS  
NWS1  
RPS  
NC  
NC  
NC  
NC  
NC  
D4  
NC  
NC  
NC  
A
NC/288M  
K
NWS0  
A
A
NC  
NC  
NC  
NC  
NC  
NC  
Q3  
D3  
NC  
B
C
D
VSS  
VSS  
A
NC  
VSS  
VSS  
VSS  
VSS  
VSS  
NC  
NC  
NC  
NC  
NC  
D5  
Q4  
NC  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VSS  
VDD  
VDD  
VDD  
VDD  
VDD  
VSS  
VSS  
VSS  
VSS  
VSS  
VSS  
VSS  
VSS  
VSS  
VDD  
VDD  
VDD  
VDD  
VDD  
VSS  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
NC  
NC  
D2  
NC  
Q2  
NC  
NC  
ZQ  
D1  
NC  
Q0  
E
F
Q5  
NC  
NC  
G
VREF  
NC  
NC  
Q6  
VDDQ  
NC  
VDDQ  
NC  
VREF  
Q1  
H
J
DOFF  
NC  
NC  
NC  
NC  
NC  
NC  
NC  
NC  
NC  
K
L
D6  
NC  
NC  
NC  
D7  
NC  
NC  
NC  
Q7  
VSS  
VSS  
VSS  
A
VSS  
A
VSS  
A
VSS  
VSS  
NC  
NC  
NC  
NC  
NC  
NC  
D0  
NC  
NC  
M
N
P
A
QVLD  
A
A
A
A
A
A
A
TDO  
TCK  
A
NC  
A
TMS  
TDI  
R
CY7C1176V18 (2M x 9)  
1
2
NC/72M  
NC  
3
6
K
9
10  
NC/36M  
NC  
11  
CQ  
Q4  
D4  
NC  
Q3  
5
NC  
7
8
4
WPS  
A
CQ  
NC  
NC  
NC  
NC  
A
NC/144M RPS  
A
A
B
C
D
NC  
NC  
NC  
Q5  
NC/288M  
A
K
BWS0  
A
A
NC  
NC  
NC  
NC  
VSS  
VSS  
NC  
VSS  
VSS  
VSS  
NC  
D5  
VSS  
VSS  
VSS  
NC  
NC  
NC  
D6  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VSS  
VDD  
VDD  
VDD  
VDD  
VDD  
VSS  
VSS  
VSS  
VSS  
VSS  
VSS  
VSS  
VSS  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
NC  
NC  
D3  
NC  
E
F
NC  
NC  
NC  
Q6  
VDD  
VDD  
VDD  
VDD  
VDD  
VSS  
NC  
NC  
ZQ  
D2  
NC  
Q1  
NC  
NC  
G
H
J
VDDQ  
NC  
VREF  
Q2  
DOFF  
NC  
VREF  
NC  
NC  
Q7  
VDDQ  
NC  
NC  
NC  
D7  
NC  
NC  
Q8  
NC  
NC  
K
L
NC  
NC  
NC  
NC  
NC  
NC  
NC  
D8  
NC  
VSS  
VSS  
VSS  
A
VSS  
A
VSS  
A
VSS  
VSS  
NC  
NC  
NC  
NC  
NC  
D0  
D1  
NC  
Q0  
M
N
P
A
QVLD  
A
A
A
A
A
A
A
TDO  
TCK  
A
NC  
A
TMS  
TDI  
R
Document Number: 001-06582 Rev. *D  
Page 4 of 29  
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Pin Configurations (continued)  
165-Ball FBGA (13 x 15 x 1.4 mm) Pinout  
CY7C1163V18 (1M x 18)  
2
3
5
BWS1  
NC  
6
7
9
10  
NC/72M  
NC  
11  
CQ  
Q8  
D8  
D7  
Q6  
Q5  
D5  
1
4
WPS  
A
8
CQ  
NC  
NC  
NC  
NC  
NC  
NC  
NC/144M NC/36M  
K
NC/288M RPS  
A
A
B
C
D
E
F
Q9  
NC  
D9  
K
BWS0  
A
A
NC  
NC  
NC  
D10  
Q10  
Q11  
D12  
Q13  
VSS  
A
NC  
VSS  
VSS  
VSS  
VSS  
VSS  
Q7  
D11  
NC  
VSS  
VSS  
VSS  
VDD  
VDD  
VSS  
VSS  
VDD  
VDD  
VSS  
NC  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
NC  
NC  
D6  
Q12  
D13  
NC  
NC  
NC  
G
VDDQ  
NC  
DOFF  
NC  
VREF  
NC  
VDDQ  
D14  
VDDQ  
VDDQ  
VDD  
VDD  
VSS  
VSS  
VDD  
VDD  
VDDQ  
VDDQ  
VREF  
Q4  
ZQ  
D4  
H
J
NC  
NC  
NC  
NC  
NC  
NC  
Q15  
NC  
Q14  
D15  
D16  
Q16  
Q17  
VDDQ  
VDDQ  
VSS  
VDD  
VSS  
VSS  
A
VSS  
VSS  
VSS  
A
VDD  
VSS  
VSS  
A
VDDQ  
VDDQ  
VSS  
NC  
D3  
NC  
Q1  
NC  
D0  
Q3  
Q2  
D2  
D1  
Q0  
K
L
NC  
NC  
NC  
NC  
M
N
P
D17  
NC  
VSS  
VSS  
A
QVLD  
A
A
A
A
A
A
A
R
TDO  
A
A
TMS  
TDI  
TCK  
NC  
CY7C1165V18 (512K x 36)  
7
1
2
3
8
RPS  
A
9
10  
11  
CQ  
Q8  
D8  
D7  
4
WPS  
A
5
6
K
NC/288M NC/72M  
NC/36M NC/144M  
A
B
C
D
CQ  
BWS2  
BWS3  
A
BWS1  
Q27  
D27  
D28  
Q29  
Q30  
D30  
Q18  
Q28  
D20  
D18  
D19  
Q19  
K
D17  
D16  
Q16  
Q17  
Q7  
BWS0  
A
VSS  
VSS  
NC  
VSS  
VSS  
VSS  
VSS  
VSS  
D15  
D29  
Q21  
D22  
VREF  
Q31  
D32  
Q24  
Q20  
D21  
Q22  
VDDQ  
D23  
Q23  
D24  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VSS  
VDD  
VDD  
VDD  
VDD  
VDD  
VSS  
VSS  
VSS  
VSS  
VSS  
VSS  
VSS  
VSS  
VSS  
VDD  
VDD  
VDD  
VDD  
VDD  
VSS  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
VDDQ  
Q15  
D14  
Q13  
VDDQ  
D12  
Q12  
D11  
D6  
Q14  
D13  
VREF  
Q4  
Q6  
Q5  
D5  
ZQ  
D4  
Q3  
Q2  
E
F
G
H
J
DOFF  
D31  
Q32  
Q33  
D33  
D34  
Q35  
D3  
K
L
Q11  
Q34  
D26  
D35  
D25  
Q25  
Q26  
VSS  
VSS  
VSS  
A
VSS  
A
VSS  
A
VSS  
VSS  
D10  
Q10  
Q9  
Q1  
D9  
D0  
D2  
D1  
Q0  
M
N
P
A
QVLD  
A
A
A
A
A
A
A
TDO  
TCK  
A
A
TMS  
TDI  
R
NC  
Document Number: 001-06582 Rev. *D  
Page 5 of 29  
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Pin Definitions  
Pin Name  
IO  
Pin Description  
Data Input Signals. Sampled on the rising edge of K and K clocks during valid write operations.  
D
Input-  
[x:0]  
Synchronous CY7C1161V18D  
[7:0]  
CY7C1176V18D  
[8:0]  
CY7C1163V18D  
CY7C1165V18D  
[17:0]  
[35:0]  
WPS  
Input-  
Synchronous a write operation is initiated. Deasserting deselects the write port. Deselecting the write port causes  
to be ignored.  
Write Port Select Active LOW. Sampled on the rising edge of the K clock. When asserted active,  
D
[x:0]  
,
1
Input-  
Nibble Write Select 0, 1 Active LOW (CY7C1161V18 Only). Sampled on the rising edge of the  
NWS , NWS  
0
Synchronous K and K clocks during Write operations. Used to select the nibble that is written into the device. NWS  
0
controls D  
and NWS controls D  
.
[3:0]  
1
[7:4]  
All the nibble write selects are sampled on the same edge as the data. Deselecting a nibble write  
select causes the corresponding nibble of data to be ignored and not written into the device.  
BWS , BWS ,  
Input-  
Byte Write Select 0, 1, 2, and 3 Active LOW. Sampled on the rising edge of the K and K clocks  
0
1
3
Synchronous during write operations. Used to select the byte that is written into the device during the current portion  
BWS , BWS  
2
of the write operation. Bytes not written remain unaltered.  
CY7C1176V18 BWS controls D  
0
[8:0].  
CY7C1163V18 BWS controls D  
and BWS controls D  
[17:9]..  
0
[8:0]  
1
CY7C1165V18 BWS controls D  
, BWS controls D  
, BWS controls D  
and BWS  
[26:18], 3  
0
[8:0]  
1
[17:9]  
2
controls D  
[35:27].  
All the Byte Write Selects are sampled on the same edge as the data. Deselecting a Byte Write Select  
causes the corresponding byte of data to be ignored and not written into the device.  
A
Input-  
Address Inputs. Sampled on the rising edge of the K clock during active read and write operations.  
Synchronous These address inputs are multiplexed for both read and write operations. Internally, the device is  
organized as 2M x 8 (4 arrays each of 512K x 8) for CY7C1161V18, 2M x 9 (4 arrays each of 512K  
x 9) for CY7C1176V18, 1M x 18 (4 arrays each of 256K x 18) for CY7C1163V18, and 512K x 36 (4  
arrays each of 128K x 36) for CY7C1165V18. Therefore, only 19 address inputs are needed to access  
the entire memory array of CY7C1161V18 and CY7C1176V18, 18 address inputs for CY7C1163V18,  
and 17 address inputs for CY7C1165V18. These inputs are ignored when the appropriate port is  
deselected.  
Q
Outputs-  
Data Output Signals. These pins drive out the requested data during a read operation. Valid data  
[x:0]  
Synchronous is driven out on the rising edge of both the K and K clocks during read operations or K and K when  
in single clock mode. When the read port is deselected, Q  
are automatically tri-stated.  
[x:0]  
CY7C1161V18 Q  
[7:0]  
[8:0]  
.
.
CY7C1176V18 Q  
CY7C1163V18 Q  
CY7C1165V18 Q  
[17:0]  
.
.
[35:0]  
RPS  
Input-  
Read Port Select Active LOW. Sampled on the rising edge of positive input clock (K). When active,  
Synchronous a read operation is initiated. Deasserting causes the read port to be deselected. When deselected,  
the pending access is enabled to complete and the output drivers are automatically tri-stated following  
the next rising edge of the K clock. Each read access consists of a burst of four sequential transfers.  
QVLD  
K
Valid Output Valid Output Indicator. Indicates valid output data. QVLD is edge-aligned with CQ and CQ.  
Indicator  
Input-  
Clock  
Positive Input Clock Input. Rising edge of K is used to capture synchronous inputs to the device  
and to drive out data through Q  
edge of K.  
when in single clock mode. All accesses are initiated on the rising  
[x:0]  
K
Input-  
Clock  
Negative Input Clock Input. K is used to capture synchronous inputs presented to the device and  
to drive out data through Q when in single clock mode.  
[x:0]  
CQ  
Echo Clock Synchronous Echo Clock Outputs. This is a free running clock and is synchronized to the input  
clock (K) of the QDR-II+. The timings for the echo clocks are shown in “Switching Characteristics”  
Document Number: 001-06582 Rev. *D  
Page 6 of 29  
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Pin Definitions (continued)  
Pin Name  
CQ  
IO  
Pin Description  
Echo Clock Synchronous Echo Clock Outputs. This is a free running clock and is synchronized to the input  
clock (K) of the QDR-II+. The timings for the echo clocks are shown in “Switching Characteristics”  
ZQ  
Input  
Input  
Output Impedance Matching Input. Used to tune the device outputs to the system data bus  
impedance. CQ, CQ and Q output impedance are set to 0.2 x RQ, where RQ is a resistor  
[x:0]  
connected between ZQ and ground. Alternatively, this pin is connected directly to V  
, which  
DDQ  
enables the minimum impedance mode. This pin cannot be connected directly to GND or left uncon-  
nected.  
DOFF  
DLL Turn Off Active LOW. Connecting this pin to ground turns off the DLL inside the device. The  
timings in the DLL turned-off operation are different from those listed in this data sheet. For normal  
operation, this pin is connected to a pull up through a 10 KΩ or less pull up resistor. The device  
behaves in QDR-I mode when the DLL is turned off. In this mode, the device operates at a frequency  
of up to 167 MHz with QDR-I timing.  
TDO  
Output  
Input  
Input  
Input  
N/A  
TDO for JTAG.  
TCK  
TCK Pin for JTAG.  
TDI  
TDI Pin for JTAG.  
TMS  
TMS Pin for JTAG.  
NC  
Not Connected to the Die. Can be tied to any voltage level.  
Not Connected to the Die. Can be tied to any voltage level.  
Not Connected to the Die. Can be tied to any voltage level.  
Not Connected to the Die. Can be tied to any voltage level.  
Not Connected to the Die. Can be tied to any voltage level.  
Reference Voltage Input. Static input used to set the reference level for HSTL inputs, outputs, and  
NC/36M  
NC/72M  
NC/144M  
NC/288M  
N/A  
N/A  
N/A  
N/A  
V
Input-  
REF  
Reference AC measurement points.  
V
V
V
Power Supply Power Supply Inputs to the Core of the Device.  
DD  
Ground  
Ground for the Device.  
SS  
Power Supply Power Supply Inputs for the Outputs of the Device.  
DDQ  
Document Number: 001-06582 Rev. *D  
Page 7 of 29  
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Write Operations  
Functional Overview  
Write operations are initiated by asserting WPS active at the  
rising edge of the positive input clock (K). On the following K  
The CY7C1161V18, CY7C1176V18, CY7C1163V18, and  
CY7C1165V18 are synchronous pipelined burst SRAMs  
equipped with both a read port and a write port. The read port is  
dedicated to read operations and the write port is dedicated to  
write operations. Data flows into the SRAM through the write port  
and out through the read port. These devices multiplex the  
address inputs in order to minimize the number of address pins  
required. By having separate read and write ports, the QDR-II+  
completely eliminates the need to “turn-around” the data bus. It  
avoids any possible data contention, thereby, simplifying system  
design. Each access consists of four 8-bit data transfers in the  
case of CY7C1161V18, four 9-bit data transfers in the case of  
CY7C1176V18, four 18-bit data transfers in the case of  
CY7C1163V18, and four 36-bit data transfers in the case of  
CY7C1165V18 in two clock cycles.  
clock rise, the data presented to D  
the lower 18-bit write data register, provided BWS  
is latched and stored into  
[17:0]  
are both  
[1:0]  
asserted active. On the subsequent rising edge of the negative  
input clock (K), the information presented to D is also stored  
[17:0]  
are both asserted  
into the write data register, provided BWS  
[1:0]  
active. This process continues for one more cycle until four 18-bit  
words (a total of 72 bits) of data are stored in the SRAM. The 72  
bits of data are then written into the memory array at the specified  
location. Therefore, write accesses to the device cannot be  
initiated on two consecutive K clock rises. The internal logic of  
the device ignores the second write request. Write accesses are  
initiated on every other rising edge of the positive input clock (K).  
Doing so pipelines the data flow such that 18 bits of data can be  
transferred into the device on every rising edge of the input  
clocks (K and K).  
Accesses for both ports are initiated on the positive input clock  
(K). All synchronous input and output timings are referenced to  
the rising edge of the Input clocks (K/K).  
When deselected, the write port ignores all inputs after the  
pending write operations are completed.  
All synchronous data inputs (D  
) pass through input registers  
[x:0]  
Byte Write Operations  
controlled by the input clocks (K and K). All synchronous data  
outputs (Q ) pass through output registers controlled by the  
[x:0]  
Byte write operations are supported by the CY7C1163V18. A  
write operation is initiated as described in the Write Operations  
section above. The bytes that are written are determined by  
BWS and BWS , which are sampled with each set of 18-bit data  
rising edge of the Input clocks (K and K) also.  
All synchronous control (RPS, WPS, BWS  
through input registers controlled by the rising edge of the input  
clocks (K and K).  
) inputs pass  
[x:0]  
0
1
words. Asserting the appropriate byte write select input during  
the data portion of a write enables the data being presented to  
be latched and written into the device. Deasserting the byte write  
select input during the data portion of a write allows the data  
stored in the device for that byte to remain unaltered. This feature  
is used to simplify read, modify, and write operations to a byte  
write operation.  
CY7C1163V18 is described in the following sections. The same  
basic descriptions apply to CY7C1161V18, CY7C1176V18, and  
CY7C1165V18.  
Read Operations  
The CY7C1163V18 is organized internally as four arrays of 256K  
x 18. Accesses are completed in a burst of four sequential 18-bit  
data words. Read operations are initiated by asserting RPS  
active at the rising edge of the positive input clock (K). The  
address presented to address inputs are stored in the Read  
address register. Following the next two K clock rises, the corre-  
sponding lowest order 18-bit word of data is driven onto the  
Concurrent Transactions  
The read and write ports on the CY7C1163V18 operate  
completely independent of one another. Because each port  
latches the address inputs on different clock edges, the user can  
read or write to any location, regardless of the transaction on the  
other port. If the ports access the same location when a read  
follows a write in successive clock cycles, the SRAM delivers the  
most recent information associated with the specified address  
location. This includes forwarding data from a write cycle initiated  
on the previous K clock rise.  
Q
using K as the output timing reference. On the subse-  
[17:0]  
quent rising edge of K, the next 18-bit data word is driven onto  
the Q . This process continues until all four 18-bit data words  
[17:0]  
have been driven out onto Q  
. The requested data is valid  
[17:0]  
0.45 ns from the rising edge of the Input clock K or K. In order to  
maintain the internal logic, each read access must be allowed to  
complete. Each read access consists of four 18-bit data words  
and takes two clock cycles to complete. Therefore, read  
accesses to the device cannot be initiated on two consecutive K  
clock rises. The internal logic of the device ignores the second  
read request. Read accesses can be initiated on every other K  
clock rise. Doing so pipelines the data flow such that data is  
transferred out of the device on every rising edge of the input  
clocks K and K.  
Read accesses and write access are scheduled such that one  
transaction is initiated on any clock cycle. If both ports are  
selected on the same K clock rise, the arbitration depends on the  
previous state of the SRAM. If both ports are deselected, the  
read port takes priority. If a read is initiated on the previous cycle,  
the write port assumes priority (because read operations cannot  
be initiated on consecutive cycles). If a write was initiated on the  
previous cycle, the read port assumes priority (because write  
operations cannot be initiated on consecutive cycles). Therefore,  
asserting both port selects active from a deselected state results  
in alternating read or write operations initiated, with the first  
access being a read.  
When the read port is deselected, the CY7C1163V18 first  
completes the pending read transactions. Synchronous internal  
circuitry automatically tri-states the outputs following the next  
rising edge of the negative input clock (K). This allows for a  
seamless transition between devices without the insertion of wait  
states in a depth expanded memory.  
Document Number: 001-06582 Rev. *D  
Page 8 of 29  
 
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Depth Expansion  
Valid Data Indicator (QVLD)  
The CY7C1163V18 has a port select input for each port. This  
enables easy depth expansion. Both port selects are only  
sampled on the rising edge of the positive input clock (K). Each  
port select input can deselect the specified port. Deselecting a  
port does not affect the other port. All pending transactions (read  
and write) are completed before the device is deselected.  
QVLD is provided on the QDR-II+ to simplify data capture on high  
speed systems. The QVLD is generated by the QDR-II+ device  
along with data output. This signal is also edge-aligned with the  
echo clock and follows the timing of any data pin. This signal is  
asserted half a cycle before valid data arrives.  
DLL  
Programmable Impedance  
These chips utilize a Delay Lock Loop (DLL) that is designed to  
function between 120 MHz and the specified maximum clock  
frequency. The DLL may be disabled by applying ground to the  
erations in QDRII/DDRII/QDRII+/DDRII+.” The DLL can also be  
reset by slowing or stopping the input clocks K and K for a  
minimum of 30 ns. However, it is not necessary for the DLL to be  
reset in order to lock to the desired frequency. During power up  
when the DOFF is tied HIGH, the DLL is locked after 2048 cycles  
of stable clock.  
An external resistor, RQ, must be connected between the ZQ pin  
on the SRAM and V to enable the SRAM to adjust its output  
SS  
driver impedance. The value of RQ must be 5X the value of the  
intended line impedance driven by the SRAM. The allowable  
range of RQ to guarantee impedance matching with a tolerance  
of ±15% is between 175Ω and 350Ω, with V  
= 1.5V. The  
DDQ  
output impedance is adjusted every 1024 cycles upon power up  
to account for drifts in supply voltage and temperature.  
Echo Clocks  
Echo clocks are provided on the QDR-II+ to simplify data capture  
on high speed systems. Two echo clocks are generated by the  
QDR-II+. CQ is referenced with respect to K and CQ is refer-  
enced with respect to K. These are free running clocks and are  
synchronized to the input clock of the QDR-II+. The timings for  
the echo clocks are shown in the AC timing table.  
Document Number: 001-06582 Rev. *D  
Page 9 of 29  
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Application Example  
Figure 1 shows four QDR-II+ used in an application.  
Figure 1. Application Example  
RQ = 250ohms  
RQ = 250ohms  
ZQ  
CQ/CQ  
Q
ZQ  
CQ/CQ  
Q
Vt  
SRAM #1  
BWS  
SRAM #4  
D
A
D
A
R
K
RPS WPS  
K
K
K
BWS  
RPS WPS  
DATA IN  
DATA OUT  
Address  
R
R
Vt  
Vt  
RPS  
BUS MASTER  
WPS  
BWS  
(CPU or ASIC)  
CLKIN/CLKIN  
Source K  
Source K  
R = 50ohms, Vt = V  
/2  
DDQ  
Truth Table  
The truth table for the CY7C1161V18, CY7C1176V18, CY7C1163V18, and CY7C1165V18 follows.  
Operation  
K
RPS WPS  
DQ  
DQ  
DQ  
DQ  
Write Cycle: Load  
address on rising edge of  
K; input write data on two  
consecutive K and K rising  
edges.  
L-H  
H
L
D(A) at K(t + 1) D(A + 1) at K(t + 1) D(A + 2) at K(t + 2) D(A + 3) at K(t + 2) ↑  
Read Cycle (2.5 Cycle  
Latency):Loadaddresson  
rising edge of K; wait one  
and a half cycle; read data  
on two consecutive K and  
K rising edges.  
L-H  
L
X
Q(A) at K(t + 2) Q(A + 1) at K(t + 3) Q(A + 2) at K(t + 3)Q(A + 3) at K(t + 4) ↑  
NOP: No operation.  
L-H  
H
X
H
X
D = X  
Q = High Z  
D = X  
Q = High Z  
D = X  
Q = High Z  
D = X  
Q = High Z  
Standby: Clock stopped. Stopped  
Previous State  
Previous State  
Previous State  
Previous State  
Notes  
2. The above application shows four QDR-II+ being used.  
3. X = “Don't Care,” H = Logic HIGH, L = Logic LOW, represents rising edge.  
4. Device powers up deselected and the outputs in a tri-state condition.  
5. “A” represents address location latched by the devices when transaction was initiated. A + 1, A + 2, and A + 3 represents the address sequence in the burst.  
6. “t” represents the cycle at which a read or write operation is started. t + 1, t + 2, t + 3 and t + 4 are the first, second, third, and fourth clock cycles, respectively succeeding  
the “t” clock cycle.  
7. Data inputs are registered at K and K rising edges. Data outputs are delivered on K and K rising edges.  
8. It is recommended that K = K = HIGH when clock is stopped. This is not essential, but permits most rapid restart by overcoming transmission line charging symmetrically.  
9. If this signal was LOW to initiate the previous cycle, this signal becomes a “Don’t Care” for this operation.  
10. This signal was HIGH on previous K clock rise. Initiating consecutive read or write operations on consecutive K clock rises is not permitted. The device ignores the  
second read or write request.  
Document Number: 001-06582 Rev. *D  
Page 10 of 29  
                 
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Write Cycle Descriptions  
[3, 11]  
The write cycle descriptions of CY7C1161V18 and CY7C1163V18 follow.  
BWS / BWS /  
0
1
K
Comments  
K
NWS  
NWS  
1
0
L
L
L
L
L–H  
During the data portion of a write sequence:  
CY7C1161V18 both nibbles (D  
) are written into the device.  
[7:0]  
CY7C1163V18 both bytes (D  
) are written into the device.  
[17:0]  
L–H  
L-H During the data portion of a write sequence:  
CY7C1161V18 both nibbles (D  
) are written into the device.  
) are written into the device.  
[7:0]  
CY7C1163V18 both bytes (D  
[17:0]  
L
H
H
L
During the data portion of a write sequence:  
CY7C1161V18 only the lower nibble (D  
) is written into the device, D  
remains unaltered.  
remains unaltered.  
[3:0]  
[7:4]  
CY7C1163V18 only the lower byte (D  
) is written into the device, D  
[8:0]  
[17:9]  
L
L–H During the data portion of a write sequence:  
CY7C1161V18 only the lower nibble (D  
) is written into the device, D  
remains unaltered.  
remains unaltered.  
[3:0]  
[7:4]  
CY7C1163V18 only the lower byte (D  
) is written into the device, D  
[8:0]  
[17:9]  
H
H
L–H  
During the data portion of a write sequence:  
CY7C1161V18 only the upper nibble (D  
) is written into the device, D  
) is written into the device, D  
remains unaltered.  
[3:0]  
[7:4]  
CY7C1163V18 only the upper byte (D  
remains unaltered.  
[17:9]  
[8:0]  
L
L–H During the data portion of a write sequence:  
CY7C1161V18 only the upper nibble (D  
) is written into the device, D  
) is written into the device, D  
remains unaltered.  
remains unaltered.  
[7:4]  
[3:0]  
[8:0]  
CY7C1163V18 only the upper byte (D  
[17:9]  
H
H
H
H
L–H  
No data is written into the device during this portion of a write operation.  
L–H No data is written into the device during this portion of a write operation.  
[3, 11]  
The write cycle operation of CY7C1176V18 follows.  
BWS  
K
L–H  
K
Comments  
0
L
L
During the data portion of a write sequence, the single byte (D  
) is written into the device.  
) is written into the device.  
[8:0]  
L–H During the data portion of a write sequence, the single byte (D  
[8:0]  
H
H
L–H  
No data is written into the device during this portion of a write operation.  
L–H No data is written into the device during this portion of a write operation.  
Note  
11. Is based upon a Write cycle was initiated per the Write Cycle Description Truth Table. NWS , NWS , BWS , BWS , BWS , and BWS can be altered on different  
0
1
0
1
2
3
portions of a Write cycle, as long as the setup and hold requirements are achieved.  
Document Number: 001-06582 Rev. *D  
Page 11 of 29  
 
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
[3, 11]  
The write cycle descriptions of CY7C1165V18 follows.  
BWS  
BWS  
BWS  
BWS  
3
K
K
Comments  
0
1
2
L
L
L
L
L–H  
During the data portion of a write sequence, all four bytes (D  
the device.  
) are written into  
) are written into  
[35:0]  
L
L
L
H
H
L
L
H
H
H
H
L
L
H
H
H
H
H
H
L
L–H  
L–H During the data portion of a write sequence, all four bytes (D  
the device.  
[35:0]  
During the data portion of a write sequence, only the lower byte (D  
) is written  
) is written  
[8:0]  
[8:0]  
into the device. D  
remains unaltered.  
[35:9]  
L
L–H During the data portion of a write sequence, only the lower byte (D  
into the device. D remains unaltered.  
[35:9]  
H
H
H
H
H
H
L–H  
During the data portion of a write sequence, only the byte (D  
) is written into  
[17:9]  
the device. D  
and D  
remains unaltered.  
[8:0]  
[35:18]  
L
L–H During the data portion of a write sequence, only the byte (D  
the device. D and D remains unaltered.  
) is written into  
[17:9]  
[8:0]  
[35:18]  
H
H
H
H
L–H  
During the data portion of a write sequence, only the byte (D  
) is written into  
) is written into  
) is written into  
) is written into  
[26:18]  
[26:18]  
[35:27]  
[35:27]  
the device. D  
and D  
remains unaltered.  
[17:0]  
[35:27]  
L
L–H During the data portion of a write sequence, only the byte (D  
the device. D and D remains unaltered.  
[17:0]  
[35:27]  
H
H
L–H  
During the data portion of a write sequence, only the byte (D  
the device. D remains unaltered.  
[26:0]  
L
L–H During the data portion of a write sequence, only the byte (D  
the device. D remains unaltered.  
[26:0]  
H
H
H
H
H
H
H
H
L–H  
No data is written into the device during this portion of a write operation.  
L–H No data is written into the device during this portion of a write operation.  
Document Number: 001-06582 Rev. *D  
Page 12 of 29  
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Instruction Register  
IEEE 1149.1 Serial Boundary Scan (JTAG)  
Three-bit instructions are serially loaded into the instruction  
register. This register is loaded when it is placed between the TDI  
page 16. Upon power up, the instruction register is loaded with  
the IDCODE instruction. It is also loaded with the IDCODE  
instruction if the controller is placed in a reset state as described  
in the previous section.  
These SRAMs incorporate a serial boundary scan test access  
port (TAP) in the FBGA package. This part is fully compliant with  
IEEE Standard 1149.1-2001. The TAP operates using JEDEC  
standard 1.8V IO logic levels.  
Disabling the JTAG Feature  
It is possible to operate the SRAM without using the JTAG  
feature. To disable the TAP controller, TCK must be tied LOW  
When the TAP controller is in the Capture IR state, the two least  
significant bits are loaded with a binary “01” pattern to allow fault  
isolation of the board level serial test path.  
(V ) to prevent clocking of the device. TDI and TMS are inter-  
SS  
nally pulled up and may be unconnected. They may alternatively  
be connected to V through a pull up resistor. TDO must be left  
unconnected. Upon power up, the device comes up in a reset  
state which does not interfere with the operation of the device.  
Bypass Register  
DD  
To save time when serially shifting data through registers, it is  
sometimes advantageous to skip certain chips. The bypass  
register is a single-bit register that can be placed between TDI  
and TDO pins. This enables data to be shifted through the SRAM  
with minimal delay. The bypass register is set LOW (V ) when  
the BYPASS instruction is executed.  
Test Access Port—Test Clock  
The test clock is used only with the TAP controller. All inputs are  
captured on the rising edge of TCK. All outputs are driven from  
the falling edge of TCK.  
SS  
Boundary Scan Register  
Test Mode Select  
The boundary scan register is connected to all of the input and  
output pins on the SRAM. Several no connect (NC) pins are also  
included in the scan register to reserve pins for higher density  
devices.  
The TMS input is used to give commands to the TAP controller  
and is sampled on the rising edge of TCK. It is allowable to leave  
this pin unconnected if the TAP is not used. The pin is pulled up  
internally, resulting in a logic HIGH level.  
The boundary scan register is loaded with the contents of the  
RAM Input and Output ring when the TAP controller is in the  
Capture-DR state and is then placed between the TDI and TDO  
pins when the controller is moved to the Shift-DR state. The  
EXTEST, SAMPLE/PRELOAD and SAMPLE Z instructions can  
be used to capture the contents of the Input and Output ring.  
Test Data In (TDI)  
The TDI pin is used to serially input information into the registers  
and can be connected to the input of any of the registers. The  
register between TDI and TDO is chosen by the instruction that  
is loaded into the TAP instruction register. For information on  
loading the instruction register, see “TAP Controller State  
Diagram” on page 15 TDI is internally pulled up and can be  
unconnected if the TAP is unused in an application. TDI is  
connected to the most significant bit (MSb) on any register.  
The “Boundary Scan Order” on page 19 show the order in which  
the bits are connected. Each bit corresponds to one of the bumps  
on the SRAM package. The MSb of the register is connected to  
TDI and the LSb is connected to TDO.  
Identification (ID) Register  
Test Data Out (TDO)  
The ID register is loaded with a vendor-specific 32-bit code  
during the Capture-DR state when the IDCODE command is  
loaded in the instruction register. The IDCODE is hardwired into  
the SRAM and can be shifted out when the TAP controller is in  
the Shift-DR state. The ID register has a vendor code and other  
The TDO output pin is used to serially clock data out from the  
registers. The output is active depending upon the current state  
of the TAP state machine, see “Instruction Codes” on page 18  
The output changes on the falling edge of TCK. TDO is  
connected to the least significant bit (LSb) of any register.  
Performing a TAP Reset  
A Reset is performed by forcing TMS HIGH (V ) for five rising  
TAP Instruction Set  
DD  
edges of TCK. This RESET does not affect the operation of the  
SRAM and may be performed while the SRAM is operating. At  
power up, the TAP is reset internally to ensure that TDO comes  
up in a high Z state.  
Eight different instructions are possible with the three-bit  
instruction register. All combinations are listed in the “Instruction  
Codes” on page 18. Three of these instructions are listed as  
RESERVED and must not be used. The other five instructions  
are described below.  
TAP Registers  
Instructions are loaded into the TAP controller during the Shift-IR  
state when the instruction register is placed between TDI and  
TDO. During this state, instructions are shifted through the  
instruction register through the TDI and TDO pins. To execute  
the instruction once it is shifted in, the TAP controller needs to be  
moved into the Update-IR state.  
Registers are connected between the TDI and TDO pins and  
enables data to be scanned into and out of the SRAM test  
circuitry. Only one register is selected at a time through the  
instruction registers. Data is serially loaded into the TDI pin on  
the rising edge of TCK. Data outputs on the TDO pin on the falling  
edge of TCK.  
Document Number: 001-06582 Rev. *D  
Page 13 of 29  
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
IDCODE  
PRELOAD enables an initial data pattern to be placed at the  
latched parallel outputs of the boundary scan register cells  
before the selection of another boundary scan test operation.  
The IDCODE instruction causes a vendor-specific 32-bit code to  
be loaded into the instruction register. It also places the  
instruction register between the TDI and TDO pins and enables  
the IDCODE to be shifted out of the device when the TAP  
controller enters the Shift-DR state. The IDCODE instruction is  
loaded into the instruction register upon power up or whenever  
the TAP controller is given a test logic reset state.  
The shifting of data for the SAMPLE and PRELOAD phases can  
occur concurrently when required—that is, while data captured  
is shifted out, the preloaded data is shifted in.  
BYPASS  
When the BYPASS instruction is loaded in the instruction register  
and the TAP is placed in a Shift-DR state, the bypass register is  
placed between the TDI and TDO pins. The advantage of the  
BYPASS instruction is that it shortens the boundary scan path  
when multiple devices are connected together on a board.  
SAMPLE Z  
The SAMPLE Z instruction causes the boundary scan register to  
be connected between the TDI and TDO pins when the TAP  
controller is in a Shift-DR state. The SAMPLE Z command puts  
the output bus into a High Z state until the next command is given  
during the Update IR state.  
EXTEST  
The EXTEST instruction enables the preloaded data to be driven  
out through the system output pins. This instruction also selects  
the boundary scan register to be connected for serial access  
between the TDI and TDO in the shift-DR controller state.  
SAMPLE/PRELOAD  
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When  
the SAMPLE/PRELOAD instructions are loaded into the instruc-  
tion register and the TAP controller is in the Capture-DR state, a  
snapshot of data on the inputs and output pins is captured in the  
boundary scan register.  
EXTEST OUTPUT BUS TRI-STATE  
IEEE Standard 1149.1 mandates that the TAP controller puts the  
output bus into a tri-state mode.  
The user must be aware that the TAP controller clock only oper-  
ates at a frequency up to 20 MHz, while the SRAM clock oper-  
ates more than an order of magnitude faster. Because there is a  
large difference in the clock frequencies, it is possible that during  
the Capture-DR state, an input or output undergoes a transition.  
The TAP then tries to capture a signal while in transition (meta-  
stable state). This does not harm the device but there is no guar-  
antee as to the value that is captured. Repeatable results are not  
possible.  
The boundary scan register has a special bit located at bit 47.  
When this scan cell, called the “extest output bus tri-state”, is  
latched into the preload register during the Update-DR state in  
the TAP controller, it directly controls the state of the output  
(Q-bus) pins, when the EXTEST is entered as the current  
instruction. When HIGH, it enables the output buffers to drive the  
output bus. When LOW, this bit places the output bus into a High  
Z condition.  
To guarantee that the boundary scan register captures the cor-  
rect value of a signal, the SRAM signal is stabilized long enough  
This bit is set by entering the SAMPLE/PRELOAD or EXTEST  
command, and then shifting the desired bit into that cell, during  
the Shift-DR state. During Update-DR, the value loaded into that  
shift register cell latches into the preload register. When the  
EXTEST instruction is entered, this bit directly controls the output  
Q-bus pins. Note that this bit is preset HIGH to enable the output  
when the device is powered up, and also when the TAP controller  
is in the Test Logic Reset state.  
to meet the TAP controller's capture setup plus hold times (t  
CS  
and t ). The SRAM clock input is not captured correctly if there  
CH  
is no way in a design to stop (or slow) the clock during a SAM-  
PLE/PRELOAD instruction. If this is an issue, it is still possible to  
capture all other signals and simply ignore the value of the CK  
and CK captured in the boundary scan register.  
Once the data is captured, it is possible to shift out the data by  
putting the TAP into the Shift-DR state. This places the boundary  
scan register between the TDI and TDO pins.  
Reserved  
These instructions are not implemented but are reserved for  
future use. Do not use these instructions.  
Document Number: 001-06582 Rev. *D  
Page 14 of 29  
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
TAP Controller State Diagram  
Figure 2. Tap Controller State Diagram  
TEST-LOGIC  
1
RESET  
0
1
1
1
TEST-LOGIC/  
IDLE  
SELECT  
DR-SCAN  
SELECT  
IR-SCAN  
0
0
0
1
1
CAPTURE-DR  
CAPTURE-IR  
0
0
SHIFT-DR  
0
1
SHIFT-IR  
0
1
1
EXIT1-DR  
0
1
EXIT1-IR  
0
0
0
PAUSE-DR  
1
PAUSE-IR  
1
0
0
EXIT2-DR  
1
EXIT2-IR  
1
UPDATE-DR  
UPDATE-IR  
1
1
0
0
Note  
12. The 0/1 next to each state represents the value at TMS at the rising edge of TCK.  
Document Number: 001-06582 Rev. *D  
Page 15 of 29  
   
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
TAP Controller Block Diagram  
Figure 3. Tap Controller Block Diagram  
0
Bypass Register  
Selection  
TDI  
Selection  
Circuitry  
2
1
0
0
0
TDO  
Circuitry  
Instruction Register  
29  
31 30  
.
.
2
1
Identification Register  
.
106 .  
.
.
2
1
Boundary Scan Register  
TCK  
TMS  
TAP Controller  
TAP Electrical Characteristics  
The Tap Electrical Characteristics table over the operating range follows.  
Parameter  
Description  
Output HIGH Voltage  
Test Conditions  
= 2.0 mA  
Min  
1.4  
1.6  
Max  
Unit  
V
V
V
V
V
V
V
I
I
I
I
I
OH1  
OH2  
OL1  
OL2  
IH  
OH  
OH  
OL  
OL  
Output HIGH Voltage  
Output LOW Voltage  
Output LOW Voltage  
Input HIGH Voltage  
= 100 μA  
= 2.0 mA  
V
0.4  
0.2  
V
= 100 μA  
V
0.65 V  
V
+ 0.3  
V
DD  
DD  
Input LOW Voltage  
–0.3  
–5  
0.35 V  
5
V
IL  
DD  
Input and Output Load Current  
GND V V  
DD  
μA  
X
I
Notes  
13. These characteristic pertain to the TAP inputs (TMS, TCK, TDI and TDO). Parallel load levels are specified in the Electrical Characteristics table.  
14. Overshoot: V (AC) < V + 0.35V (pulse width less than t /2)  
/2), Undershoot: V (AC) > 0.3V (pulse width less than t  
IH  
DDQ  
CYC  
IL  
CYC  
15. All voltage referenced to ground.  
Document Number: 001-06582 Rev. *D  
Page 16 of 29  
       
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
TAP AC Switching Characteristics  
The Tap AC Switching Characteristics over the operating range follows.  
Parameter  
Description  
Min  
Max  
Unit  
ns  
t
t
t
t
TCK Clock Cycle Time  
TCK Clock Frequency  
TCK Clock HIGH  
50  
TCYC  
20  
MHz  
ns  
TF  
TH  
TL  
20  
20  
TCK Clock LOW  
ns  
Setup Times  
t
t
t
TMS Setup to TCK Clock Rise  
TDI Setup to TCK Clock Rise  
Capture Setup to TCK Rise  
5
5
5
ns  
ns  
ns  
TMSS  
TDIS  
CS  
Hold Times  
t
t
t
TMS Hold after TCK Clock Rise  
TDI Hold after Clock Rise  
5
5
5
ns  
ns  
ns  
TMSH  
TDIH  
CH  
Capture Hold after Clock Rise  
Output Times  
t
t
TCK Clock LOW to TDO Valid  
TCK Clock LOW to TDO Invalid  
10  
ns  
ns  
TDOV  
TDOX  
0
TAP Timing and Test Conditions  
The Tap Timing and Test Conditions for the CY7C1161V18, CY7C1176V18, CY7C1163V18, and CY7C1165V18 follows.  
0.9V  
ALL INPUT PULSES  
50Ω  
1.8V  
TDO  
0.9V  
0V  
Z = 50  
Ω
0
C = 20 pF  
L
tTL  
tTH  
GND  
(a)  
Test Clock  
TCK  
tTCYC  
tTMSH  
tTMSS  
Test Mode Select  
TMS  
tTDIS  
tTDIH  
Test Data In  
TDI  
Test Data Out  
TDO  
tTDOV  
tTDOX  
Notes  
16. t and t refer to the setup and hold time requirements of latching data from the boundary scan register.  
CS  
CH  
17. Test conditions are specified using the load in TAP AC test conditions. t /t = 1 ns.  
R
F
Document Number: 001-06582 Rev. *D  
Page 17 of 29  
   
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Identification Register Definitions  
Value  
Instruction Field  
Description  
CY7C1161V18  
CY7C1176V18  
000  
CY7C1163V18  
000  
CY7C1165V18  
Revision Number  
(31:29)  
000  
000  
Version number.  
Cypress Device ID 11010010001000101 11010010001001101 11010010001010101 11010010001100101 Defines the type of  
(28:12)  
SRAM.  
Cypress JEDEC ID  
(11:1)  
00000110100  
1
00000110100  
1
00000110100  
1
00000110100  
1
Enables unique  
identification of  
SRAM vendor.  
ID Register  
Presence (0)  
Indicates the  
presence of an ID  
register.  
Scan Register Sizes  
Register Name  
Bit Size  
Instruction  
Bypass  
3
1
ID  
32  
107  
Boundary Scan  
Instruction Codes  
Instruction  
EXTEST  
Code  
000  
Description  
Captures the input and output ring contents.  
IDCODE  
001  
Loads the ID register with the vendor ID code and places the register between TDI  
and TDO. This operation does not affect SRAM operation.  
SAMPLE Z  
010  
Captures the input and output contents. Places the boundary scan register between  
TDI and TDO. This forces all SRAM output drivers to a High Z state.  
RESERVED  
011  
100  
Do Not Use: This instruction is reserved for future use.  
SAMPLE/PRELOAD  
Captures the input and output ring contents. Places the boundary scan register  
between TDI and TDO. This operation does not affect the SRAM operation.  
RESERVED  
RESERVED  
BYPASS  
101  
110  
111  
Do Not Use: This instruction is reserved for future use.  
Do Not Use: This instruction is reserved for future use.  
Places the bypass register between TDI and TDO. This operation does not affect  
SRAM operation.  
Document Number: 001-06582 Rev. *D  
Page 18 of 29  
   
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Boundary Scan Order  
Bit #  
0
Bump ID  
6R  
Bit #  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
Bump ID  
11H  
10G  
9G  
Bit #  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
73  
74  
75  
76  
77  
78  
79  
80  
Bump ID  
7B  
6B  
6A  
5B  
5A  
4A  
5C  
4B  
3A  
1H  
1A  
2B  
3B  
1C  
1B  
3D  
3C  
1D  
2C  
3E  
2D  
2E  
1E  
2F  
Bit #  
81  
Bump ID  
3G  
2G  
1J  
1
6P  
82  
2
6N  
83  
3
7P  
11F  
11G  
9F  
84  
2J  
4
7N  
85  
3K  
3J  
5
7R  
86  
6
8R  
10F  
11E  
10E  
10D  
9E  
87  
2K  
1K  
2L  
7
8P  
88  
8
9R  
89  
9
11P  
10P  
10N  
9P  
90  
3L  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
91  
1M  
1L  
10C  
11D  
9C  
92  
93  
3N  
3M  
1N  
2M  
3P  
2N  
2P  
1P  
3R  
4R  
4P  
5P  
5N  
5R  
10M  
11N  
9M  
94  
9D  
95  
11B  
11C  
9B  
96  
9N  
97  
11L  
11M  
9L  
98  
10B  
11A  
Internal  
9A  
99  
100  
101  
102  
103  
104  
105  
106  
10L  
11K  
10K  
9J  
8B  
7C  
9K  
6C  
3F  
10J  
11J  
8A  
1G  
1F  
7A  
Document Number: 001-06582 Rev. *D  
Page 19 of 29  
 
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Power Up Sequence in QDR-II+ SRA  
DLL Constraints  
During power up, when the DOFF is tied HIGH, the DLL gets  
locked after 2048 cycles of stable clock. QDR-II+ SRAMs must  
be powered up and initialized in a predefined manner to prevent  
undefined operations.  
DLL uses K clock as its synchronizing input. The input must  
have low phase jitter, which is specified as t  
KC Var  
The DLL functions at frequencies down to 120 MHz  
If the input clock is unstable and the DLL is enabled, then the  
DLL locks onto an incorrect frequency, causing unstable SRAM  
behavior. To avoid this, provide 2048 cycles stable clock to  
relock to the desired clock frequency  
Power Up Sequence  
Apply power with DOFF tied HIGH (All other inputs can be  
HIGH or LOW)  
Apply V before V  
DD  
DDQ  
Apply V  
before V  
or at the same time as V  
DDQ  
REF REF  
Provide stable power and clock (K, K) for 2048 cycles to lock  
the DLL  
Power Up Waveforms  
Figure 4. Power Up Waveforms  
K
K
Start Normal  
Operation  
Unstable Clock  
> 2048 Stable Clock  
Clock Start (Clock Starts after V /V  
DD DDQ  
is Stable)  
V
/V  
+
V
/V Stable (< 0.1V DC per 50 ns)  
DD DDQ  
DD DDQ  
Fix HIGH (tie to V  
DDQ  
)
DOFF  
Document Number: 001-06582 Rev. *D  
Page 20 of 29  
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Current into Outputs (LOW)......................................... 20 mA  
Static Discharge Voltage (MIL-STD-883, M. 3015).. > 2001V  
Latch up Current.................................................... > 200 mA  
Maximum Ratings  
Exceeding maximum ratings may impair the useful life of the  
device. User guidelines are not tested.  
Storage Temperature ................................ –65°C to + 150°C  
Ambient Temperature with Power Applied. –55°C to + 125°C  
Operating Range  
Ambient  
Supply Voltage on V Relative to GND .......–0.5V to + 2.9V  
V
DDQ  
DD  
Range  
Commercial  
Industrial  
Temperature (T )  
V
A
DD  
Supply Voltage on V  
Relative to GND..... –0.5V to + V  
DD  
DDQ  
0°C to +70°C  
1.8 ± 0.1V  
1.4V to  
DC Applied to Outputs in High Z ........0.5V to V  
+ 0.3V  
V
DDQ  
DD  
–40°C to +85°C  
DC Input Voltage ...............................0.5V to V + 0.3V  
DD  
Electrical Characteristics  
The DC Electrical Characteristics over the operating range follows.  
Parameter  
Description  
Power Supply Voltage  
IO Supply Voltage  
Test Conditions  
Min  
1.7  
1.4  
Typ  
Max  
Unit  
V
1.8  
1.5  
1.9  
V
V
DD  
V
V
V
V
V
V
V
I
V
DD  
DDQ  
OH  
Output HIGH Voltage  
Output LOW Voltage  
Output HIGH Voltage  
Output LOW Voltage  
Input HIGH Voltage  
Input LOW Voltage  
V
V
/2 – 0.12  
/2 – 0.12  
– 0.2  
V
V
/2 + 0.12  
/2 + 0.12  
V
DDQ  
DDQ  
DDQ  
V
OL  
DDQ  
I
I
= 0.1 mA, Nominal Impedance  
V
V
V
OH(LOW)  
OL(LOW)  
IH  
OH  
OL  
DDQ  
DDQ  
= 0.1 mA, Nominal Impedance  
V
0.2  
V
SS  
V
+ 0.1  
V
+ 0.15  
– 0.1  
REF  
V
REF  
DDQ  
–0.15  
V
V
IL  
Input Leakage Current  
Output Leakage Current  
Input Reference Voltage  
GND V V  
2  
2  
2
μA  
μA  
V
X
I
DDQ  
I
GND V V  
Output Disabled  
2
OZ  
I
DDQ,  
V
Typical Value = 0.75V  
0.68  
0.75  
0.95  
850  
920  
1020  
1080  
250  
260  
290  
300  
REF  
I
V
Operating Supply  
V
= Max, I  
= 0 mA, 300 MHz  
333 MHz  
mA  
mA  
mA  
mA  
mA  
mA  
mA  
mA  
DD  
DD  
DD  
OUT  
CYC  
f = f  
= 1/t  
max  
375 MHz  
400 MHz  
I
Automatic Power Down  
Current  
Max V  
,
300 MHz  
SB1  
DD  
Both Ports Deselected,  
333 MHz  
375 MHz  
400 MHz  
V
V or V V  
IN  
IH  
IN  
IL  
f = f  
= 1/t  
,
max  
CYC  
Inputs Static  
AC Electrical Characteristics  
Over the operating range follows.  
Parameter  
Description  
Input HIGH Voltage  
Input LOW Voltage  
Test Conditions  
Min  
Typ  
Max  
Unit  
V
V
V
+ 0.2  
V
+ 0.24  
DDQ  
IH  
IL  
REF  
V
–0.24  
V
– 0.2  
V
REF  
Notes  
18. Power up: Is based upon a linear ramp from 0V to V (min) within 200 ms. During this time V < V and V  
< V  
.
DD  
DD  
IH  
DD  
DDQ  
19. Output are impedance controlled. I = (V  
/2)/(RQ/5) for values of 175Ω < RQ < 350Ω.  
OH  
DDQ  
20. Output are impedance controlled. I = (V  
/2)/(RQ/5) for values of 175Ω < RQ < 350Ω.  
OL  
DDQ  
21. V  
(min) = 0.68V or 0.46V  
, whichever is larger, V  
(max) = 0.95V or 0.54V  
, whichever is smaller.  
DDQ  
REF  
DDQ  
REF  
22. The operation current is calculated with 50% read cycle and 50% write cycle.  
Document Number: 001-06582 Rev. *D  
Page 21 of 29  
         
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Capacitance  
Tested initially and after any design or process change that may affect these parameters.  
Parameter Description Test Conditions  
Input Capacitance T = 25°C, f = 1 MHz,  
Max  
Unit  
pF  
C
5
6
7
IN  
A
V
= 1.8V  
DD  
V
C
C
Clock Input Capacitance  
Output Capacitance  
pF  
CLK  
O
= 1.5V  
DDQ  
pF  
Thermal Resistance  
Tested initially and after any design or process change that may affect these parameters.  
165 FBGA  
Package  
Parameter  
Description  
Test Conditions  
Unit  
Θ
Thermal Resistance  
(junction to ambient)  
Test conditions follow standard test methods and  
procedures for measuring thermal impedance, in  
accordance with EIA/JESD51.  
17.2  
°C/W  
JA  
Θ
Thermal Resistance  
(junction to case)  
4.15  
°C/W  
JC  
AC Test Loads and Waveforms  
Figure 5. AC Test Loads and Waveforms  
VREF = 0.75V  
0.75V  
VREF  
VREF  
0.75V  
R = 50Ω  
OUTPUT  
[23]  
ALL INPUT PULSES  
Z = 50Ω  
0
OUTPUT  
1.25V  
Device  
R = 50Ω  
L
0.75V  
Under  
Device  
Under  
0.25V  
Test  
5 pF  
VREF = 0.75V  
Slew Rate = 2 V/ns  
ZQ  
Test  
ZQ  
RQ =  
RQ =  
250Ω  
250Ω  
INCLUDING  
JIG AND  
SCOPE  
(a)  
(b)  
Notes  
23. Unless otherwise noted, test conditions are based upon signal transition time of 2V/ns, timing reference levels of 0.75V, Vref = 0.75V, RQ = 250Ω, V  
= 1.5V, input  
DDQ  
pulse levels of 0.25V to 1.25V, and output loading of the specified I /I and load capacitance shown in (a) of AC Test Loads.  
OL OH  
Document Number: 001-06582 Rev. *D  
Page 22 of 29  
   
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Switching Characteristics  
Over the operating range  
400 MHz  
375 MHz  
333 MHz  
300 MHz  
Cypress Consortium  
Parameter Parameter  
Description  
Unit  
Min Max Min Max Min Max Min Max  
t
t
t
t
t
V
(Typical) to the First Access  
1
1
1
1
ms  
ns  
POWER  
CYC  
KH  
DD  
t
t
t
t
K Clock Cycle Time  
2.50 8.40 2.66 8.40 3.0 8.40 3.3 8.40  
KHKH  
KHKL  
KLKH  
KHKH  
Input Clock (K/K) HIGH  
Input Clock (K/K) LOW  
0.4  
0.4  
0.4  
0.4  
0.4  
0.4  
0.4  
0.4  
t
t
CYC  
KL  
CYC  
K Clock Rise to K Clock Rise  
(rising edge to rising edge)  
1.06  
1.13  
1.28  
1.40  
ns  
KHKH  
Setup Times  
t
t
t
t
t
t
Address Setup to K Clock Rise  
0.4  
0.4  
0.4  
0.4  
0.4  
0.4  
0.4  
0.4  
ns  
ns  
ns  
SA  
AVKH  
IVKH  
IVKH  
Control Setup to K Clock Rise (RPS, WPS)  
SC  
Double Data Rate Control Setup to Clock (K, K) 0.28  
Rise (BWS , BWS BWS , BWS )  
0.28  
0.28  
0.28  
SCDDR  
0
1,  
2
3
t
t
D Setup to Clock (K/K) Rise  
[X:0]  
0.28  
0.28  
0.28  
0.28  
ns  
SD  
DVKH  
Hold Times  
t
t
t
t
t
t
Address Hold after K Clock Rise  
Control Hold after K Clock Rise (RPS, WPS)  
0.4  
0.4  
0.4  
0.4  
0.4  
0.4  
0.4  
0.4  
ns  
ns  
ns  
HA  
KHAX  
KHIX  
KHIX  
HC  
Double Data Rate Control Hold after Clock (K/K) 0.28  
Rise (BWS , BWS BWS , BWS )  
0.28  
0.28  
0.28  
HCDDR  
0
1,  
2
3
t
t
D Hold after Clock (K/K) Rise  
[X:0]  
0.28  
0.28  
0.28  
0.28  
ns  
HD  
KHDX  
Output Times  
t
t
t
t
K/K Clock Rise to Data Valid  
0.45  
0.45  
0.45  
0.45  
ns  
ns  
CO  
CHQV  
CHQX  
Data Output Hold after Output K/K Clock Rise –0.45  
(Active to Active)  
–0.45  
–0.45  
–0.45  
DOH  
t
t
t
t
t
t
t
t
t
t
t
t
K/K Clock Rise to Echo Clock Valid  
Echo Clock Hold after K/K Clock Rise  
Echo Clock High to Data Valid  
0.45  
0.45  
0.45  
0.45  
ns  
ns  
ns  
ns  
ns  
ns  
CCQO  
CQOH  
CQD  
CHCQV  
CHCQX  
CQHQV  
CQHQX  
CQHCQL  
CQHCQH  
–0.45  
–0.45  
–0.45  
–0.45  
0.2  
0.2  
0.2  
0.2  
Echo Clock High to Data Invalid  
–0.2  
0.81  
0.81  
–0.2  
0.88  
0.88  
–0.2  
1.03  
1.03  
–0.2  
1.15  
1.15  
CQDOH  
CQH  
Output Clock (CQ/CQ) HIGH  
CQ Clock Rise to CQ Clock Rise  
CQHCQH  
(rising edge to rising edge)  
t
t
t
t
t
t
Clock (K/K) Rise to High Z (Active to High Z)  
0.45  
0.45  
0.45  
0.45  
ns  
ns  
ns  
CHZ  
CLZ  
CHQZ  
CHQX1  
QVLD  
Clock (K/K) Rise to Low Z  
–0.45  
–0.45  
–0.45  
–0.45  
Echo Clock High to QVLD Valid  
–0.20 0.20 –0.20 0.20 –0.20 0.20 –0.20 0.20  
QVLD  
Notes  
24. When a part with a maximum frequency above 300 MHz is operating at a lower clock frequency, it requires the input timings of the frequency range in which it is being  
operated and outputs data with the output timings of that frequency range.  
25. This part has a voltage regulator internally; t  
is the time that the power needs to be supplied above V minimum initially before a Read or Write operation can  
POWER  
DD  
be initiated.  
26. These parameters are extrapolated from the input timing parameters (t  
– 250 ps, where 250 ps is the internal jitter. An input jitter of 200 ps (t  
) is already  
KHKH  
KC Var  
included in the t  
). These parameters are only guaranteed by design and are not tested in production.  
KHKH  
27. t  
, t  
are specified with a load capacitance of 5 pF as in part (b) of AC Test Loads and Waveforms. Transition is measured ± 100 mV from steady state voltage.  
CHZ CLZ  
28. At any voltage and temperature t  
is less than t  
and t  
less than t  
.
CHZ  
CLZ  
CHZ  
CO  
29. t  
spec is applicable for both rising and falling edges of QVLD signal.  
QVLD  
Document Number: 001-06582 Rev. *D  
Page 23 of 29  
             
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Switching Characteristics  
[23, 24]  
Over the operating range  
(continued)  
400 MHz  
375 MHz  
333 MHz  
300 MHz  
Cypress Consortium  
Parameter Parameter  
Description  
Unit  
Min Max Min Max Min Max Min Max  
DLL Timing  
t
t
t
t
t
t
Clock Phase Jitter  
0.20  
0.20  
0.20  
0.20  
ns  
Cycles  
ns  
KC Var  
KC Var  
DLL Lock Time (K)  
2048  
30  
2048  
30  
2048  
30  
2048  
30  
KC lock  
KC Reset  
KC lock  
KC Reset  
K Static to DLL Reset  
Note  
30. Hold to >V or <V .  
IH  
IL  
Document Number: 001-06582 Rev. *D  
Page 24 of 29  
 
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Switching Waveforms  
Read/Write/Deselect Sequence  
Figure 6. Waveform for 2.5 Cycle Read Latency  
WRITE  
3
READ  
4
NOP  
1
READ  
2
WRITE  
5
NOP  
6
7
8
K
t
t
KL  
t
t
KH  
CYC  
KHKH  
K
RPS  
t
t
SC HC  
t
t
SC  
HC  
WPS  
A
A0  
A1  
A2  
A3  
t
t
HD  
t
t
HD  
SA  
HA  
t
SD  
t
SD  
D11  
D12  
D30  
D32  
D33  
t
D10  
QVLD  
D13  
D31  
D
QVLD  
t
QVLD  
t
DOH  
t
t
CQDOH  
CO  
t
t
CHZ  
t
CLZ  
t
CQD  
Q
Q00 Q01 Q02  
CCQO  
Q20 Q21 Q22  
Q23  
Q03  
(Read Latency = 2.5 Cycles)  
CQOH  
CQ  
CQ  
CCQO  
t
t
t
CQHCQH  
CQH  
CQOH  
DON’T CARE  
UNDEFINED  
Notes  
31. Q00 refers to output from address A0. Q01 refers to output from the next internal burst address following A0, i.e., A0+1.  
32. Outputs are disabled (High Z) one clock cycle after a NOP.  
33. In this example, if address A2 = A1, then data Q20 = D10 and Q21 = D11. Write data is forwarded immediately as read results. This note applies to the whole diagram.  
Document Number: 001-06582 Rev. *D  
Page 25 of 29  
     
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Ordering Information  
Not all of the speed, package and temperature ranges are available. Contact your local sales representative or visit www.cypress.com  
for actual products offered.  
Speed  
(MHz)  
Package  
Diagram  
Operating  
Range  
Ordering Code  
Package Type  
400 CY7C1161V18-400BZC  
CY7C1176V18-400BZC  
CY7C1163V18-400BZC  
CY7C1165V18-400BZC  
CY7C1161V18-400BZXC  
CY7C1176V18-400BZXC  
CY7C1163V18-400BZXC  
CY7C1165V18-400BZXC  
CY7C1161V18-400BZI  
CY7C1176V18-400BZI  
CY7C1163V18-400BZI  
CY7C1165V18-400BZI  
CY7C1161V18-400BZXI  
CY7C1176V18-400BZXI  
CY7C1163V18-400BZXI  
CY7C1165V18-400BZXI  
375 CY7C1161V18-375BZC  
CY7C1176V18-375BZC  
CY7C1163V18-375BZC  
CY7C1165V18-375BZC  
CY7C1161V18-375BZXC  
CY7C1176V18-375BZXC  
CY7C1163V18-375BZXC  
CY7C1165V18-375BZXC  
CY7C1161V18-375BZI  
CY7C1176V18-375BZI  
CY7C1163V18-375BZI  
CY7C1165V18-375BZI  
CY7C1161V18-375BZXI  
CY7C1176V18-375BZXI  
CY7C1163V18-375BZXI  
CY7C1165V18-375BZXI  
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)  
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free  
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)  
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free  
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)  
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free  
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)  
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free  
Commercial  
Industrial  
Commercial  
Industrial  
Document Number: 001-06582 Rev. *D  
Page 26 of 29  
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Ordering Information (continued)  
Not all of the speed, package and temperature ranges are available. Contact your local sales representative or visit www.cypress.com  
for actual products offered.  
Speed  
(MHz)  
Package  
Diagram  
Operating  
Range  
Ordering Code  
Package Type  
333 CY7C1161V18-333BZC  
CY7C1176V18-333BZC  
CY7C1163V18-333BZC  
CY7C1165V18-333BZC  
CY7C1161V18-333BZXC  
CY7C1176V18-333BZXC  
CY7C1163V18-333BZXC  
CY7C1165V18-333BZXC  
CY7C1161V18-333BZI  
CY7C1176V18-333BZI  
CY7C1163V18-333BZI  
CY7C1165V18-333BZI  
CY7C1161V18-333BZXI  
CY7C1176V18-333BZXI  
CY7C1163V18-333BZXI  
CY7C1165V18-333BZXI  
300 CY7C1161V18-300BZC  
CY7C1176V18-300BZC  
CY7C1163V18-300BZC  
CY7C1165V18-300BZC  
CY7C1161V18-300BZXC  
CY7C1176V18-300BZXC  
CY7C1163V18-300BZXC  
CY7C1165V18-300BZXC  
CY7C1161V18-300BZI  
CY7C1176V18-300BZI  
CY7C1163V18-300BZI  
CY7C1165V18-300BZI  
CY7C1161V18-300BZXI  
CY7C1176V18-300BZXI  
CY7C1163V18-300BZXI  
CY7C1165V18-300BZXI  
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)  
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free  
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)  
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free  
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)  
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free  
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)  
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free  
Commercial  
Industrial  
Commercial  
Industrial  
Document Number: 001-06582 Rev. *D  
Page 27 of 29  
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Package Diagram  
Figure 7. 165-Ball FBGA (13 x 15 x 1.4 mm), 51-85180  
BOTTOM VIEW  
PIN 1 CORNER  
TOP VIEW  
Ø0.05 M C  
Ø0.25 M C A B  
-0.06  
PIN 1 CORNER  
Ø0.50  
(165X)  
+0.14  
1
2
3
4
5
6
7
8
9
10  
11  
11 10  
9
8
7
6
5
4
3
2
1
A
B
A
B
C
D
C
D
E
E
F
F
G
G
H
J
H
J
K
K
L
L
M
M
N
P
R
N
P
R
A
A
1.00  
5.00  
10.00  
13.00 0.10  
B
13.00 0.10  
B
0.15(4X)  
NOTES :  
SOLDER PAD TYPE : NON-SOLDER MASK DEFINED (NSMD)  
PACKAGE WEIGHT : 0.475g  
JEDEC REFERENCE : MO-216 / DESIGN 4.6C  
PACKAGE CODE : BB0AC  
SEATING PLANE  
C
51-85180-*A  
Document Number: 001-06582 Rev. *D  
Page 28 of 29  
CY7C1161V18, CY7C1176V18  
CY7C1163V18, CY7C1165V18  
Document History Page  
Document Title: CY7C1161V18/CY7C1176V18/CY7C1163V18/CY7C1165V18, 18-Mbit QDR™-II+ SRAM 4-Word Burst Archi-  
tecture (2.5 Cycle Read Latency)  
Document Number: 001-06582  
Orig. of  
Change  
REV.  
ECN No. Issue Date  
Description of Change  
**  
430351  
461654  
See ECN  
See ECN  
NXR  
New data sheet  
*A  
NXR  
Revised the MPNs from  
CY7C1176BV18 to CY7C1176V18  
CY7C1163BV18 to CY7C1163V18  
CY7C1165BV18 to CY7C1165V18  
Changed t and t from 40 ns to 20 ns, changed t  
, t  
, t , t  
, t  
,
TH  
TL  
TMSS TDIS CS TMSH TDIH  
t
from 10 ns to 5 ns and changed t  
from 20 ns to 10 ns in TAP AC  
CH  
TDOV  
Switching Characteristics table  
Modified power up waveform  
*B  
497629  
See ECN  
NXR  
Changed the V  
operating voltage to 1.4V to V in the Features section, in  
DDQ DD  
Operating Range table and in the DC Electrical Characteristics table  
Added foot note in page 1  
Changed the Maximum rating of Ambient Temperature with Power Applied from  
–10°C to +85°C to –55°C to +125°C  
Changed V  
(max) spec from 0.85V to 0.95V in the DC Electrical Character-  
REF  
istics table and in the note below the table  
Updated foot note 22 to specify Overshoot and Undershoot Spec  
Updated Θ and Θ values  
JA  
JC  
Removed x9 part and its related information  
Updated footnote 25  
*C  
1167806  
See ECN VKN/KKVTMP Converted from preliminary to final  
Added x8 and x9 parts  
Changed I values from 800 mA to 1080 mA for 400 MHz, 766 mA to 1020 mA  
DD  
for 375 MHz, 708 mA to 920 mA for 333 MHz, 663 mA to 850 mA for 300 MHz  
Changed I values from 235 mA to 300 mA for 400 MHz, 227 mA to 290 mA  
SB  
for 375 MHz, 212 mA to 260 mA for 333 MHz, 201 mA to 250 mA for 300 MHz  
Changed t  
spec to 8.4 ns for all speed bins  
CYC(max)  
Changed Θ value from 13.48 °C/W to 17.2 °C/W  
JA  
Updated Ordering Information table  
*D  
2199066 See ECN  
VKN/AESA Added footnote# 22 related to I  
DD  
© Cypress Semiconductor Corporation, 2006-2008. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of  
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for  
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as  
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems  
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.  
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),  
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,  
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress  
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without  
the express written permission of Cypress.  
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES  
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not  
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where  
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer  
assumes all risk of such use and in doing so indemnifies Cypress against all charges.  
Use may be limited by and subject to the applicable Cypress software license agreement.  
Document Number: 001-06582 Rev. *D  
Revised March 06, 2008  
Page 29 of 29  
QDR™ is a trademark of Cypress Semiconductor Corp. QDR RAMs and Quad Data Rate RAMs comprise a new family of products developed by Cypress, IDT, NEC, Renesas, and Samsung. All  
product and company names mentioned in this document are the trademarks of their respective holders.  

Gigabyte PHASER 4500 User Manual
GE Monogram ZEW165 User Manual
Electrolux Air O Convect 269004 User Manual
Eizo Nanao Computer Monitor ColorEdge Calibration Color LCD Monitor User Manual
Eizo Nanao Computer Monitor CG232W User Manual
Cypress CY8C24094 User Manual
Cypress CY7C68024 User Manual
Black Box Computer Hardware LBPS311A User Manual
ASRock Computer Hardware Wolfdale1333 GLAN User Manual
Aiphone Conference Phone LE D User Manual