Advantech FPM 3150G User Manual

FPM-3150G Series  
15" XGA TFT LCD Industrial  
Monitor with VGA and DVI Inputs  
User Manual  
Product Warranty (2 years)  
Advantech warrants to you, the original purchaser, that each of its prod-  
ucts will be free from defects in materials and workmanship for two years  
from the date of purchase.  
This warranty does not apply to any products which have been repaired or  
altered by persons other than repair personnel authorized by Advantech,  
or which have been subject to misuse, abuse, accident or improper instal-  
lation. Advantech assumes no liability under the terms of this warranty as  
a consequence of such events.  
All defective products under normal / standard operation will be serviced  
by Advantech’s global RMA system. If an Advantech product is defec-  
tive, it will be repaired or replaced at no charge during the warranty  
period. For out-of-warranty repairs, you will be billed according to the  
cost of replacement materials, service time and freight. Please consult  
your dealer for more details.  
If you think you have a defective product, follow these steps:  
1.  
Collect all the information about the problem encountered. (For  
example, CPU speed, Advantech products used, other hardware  
and software used, etc.) Note anything abnormal and list any  
onscreen messages you get when the problem occurs.  
2.  
3.  
Call your dealer and describe the problem. Please have your man-  
ual, product, and any helpful information readily available.  
If your product is diagnosed as defective, obtain an RMA (return  
merchandize authorization) number from your dealer. This allows  
us to process your return more quickly.  
4.  
5.  
Carefully pack the defective product, a fully-completed Repair and  
Replacement Order Card and a photocopy proof of purchase date  
(such as your sales receipt) in a shippable container. A product  
returned without proof of the purchase date is not eligible for war-  
ranty service.  
Write the RMA number visibly on the outside of the package and  
ship it prepaid to your dealer.  
iii  
FCC Class B  
This equipment has been tested and found to comply with the limits for a  
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection against harmful interfer-  
ence when the equipment is operated in a residential environment. This  
equipment generates, uses and can radiate radio frequency energy. If not  
installed and used in accordance with this user's manual, it may cause  
harmful interference to radio communications. Note that even when this  
equipment is installed and used in accordance with this user’s manual,  
there is still no guarantee that interference will not occur. If this equip-  
ment is believed to be causeing harmful interference to radio or television  
reception, this can be determined by turning the equipment on and off. If  
the interference is occurring, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna  
• Increase the separation between the equipment and the receiver  
• Connect the equipment to a power outlet on a circuit different from that  
to which the receiver is connected  
• Consult the dealer or an experienced radio/TV technician for help  
FPM-3150 Series User Manual  
iv  
Packing List  
Before installing your equipment, make sure that the following materials  
have been received:  
• FPM-3150G Series flat panel monitor  
• Accessory pack, including:  
- AC/DC adapter  
- AC/DC power adapter bracket  
- DC in Power Cord Bracket x 1 piece  
- Video Signal Cable, 1.8m  
- Panel/Wall mount bracket x 2  
- Panel sponge x 4  
- RS-232 cable, 1.8m (FPM-3150G-R only)  
- Screw Bag (M6x35mm screws with spring by 4 pieces)  
- Driver / Manual CD-ROM  
If any of these items are missing or damaged, contact your distributor or  
sales representative immediately.  
Additional Information and Assistance  
find the latest information about the product.  
2. Contact your distributor, sales representative, or Advantech's  
customer service center for technical support if you need additional  
assistance. Please have the following information ready before you  
call:  
• Product name and serial number  
• Description of your peripheral attachments  
• Description of your software (operating system, version, application  
software, etc.)  
• A complete description of the problem  
• The exact wording of any error messages  
v
Safety Instructions  
1.  
2.  
3.  
Read these safety instructions carefully.  
Keep this User's Manual for later reference.  
Disconnect this equipment from any AC outlet before cleaning.  
Use a damp cloth. Do not use liquid or spray detergents for clean-  
ing.  
4.  
For plug-in equipment, the power outlet socket must be located  
near the equipment and must be easily accessible.  
5.  
6.  
Keep this equipment away from humidity.  
Put this equipment on a reliable surface during installation. Drop-  
ping it or letting it fall may cause damage.  
7.  
8.  
9.  
The openings on the enclosure are for air convection. Protect the  
equipment from overheating. DO NOT COVER THE OPENINGS.  
Make sure the voltage of the power source is correct before con-  
necting the equipment to the power outlet.  
Position the power cord so that people cannot step on it. Do not  
place anything over the power cord.  
10. All cautions and warnings on the equipment should be noted.  
11. If the equipment is not used for a long time, disconnect it from the  
power source to avoid damage by transient overvoltage.  
12. Never pour any liquid into an opening. This may cause fire or elec-  
trical shock.  
13. Never open the equipment. For safety reasons, the equipment  
should be opened only by qualified service personnel.  
14. If one of the following situations arises, get the equipment checked  
by service personnel:  
a. The power cord or plug is damaged.  
b. Liquid has penetrated into the equipment.  
c. The equipment has been exposed to moisture.  
d. The equipment does not work well, or you cannot get it to work  
according to the user's manual.  
e. The equipment has been dropped and damaged.  
f. The equipment has obvious signs of breakage.  
FPM-3150 Series User Manual  
vi  
15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCON-  
TROLLED ENVIRONMENT WHERE THE STORAGE TEM-  
PERATURE IS BELOW -20° C (-4° F) OR ABOVE 60° C (140°  
F). THIS MAY DAMAGE THE EQUIPMENT.  
The sound pressure level at the operator's position according to IEC 704-  
1:1982 is no more than 70dB(A).  
DISCLAIMER: This set of instructions is given according to IEC 704-1.  
Advantech disclaims all responsibility for the accuracy of any statements  
contained herein.  
Wichtige Sicherheishinweise  
1.  
2.  
3.  
Bitte lesen sie Sich diese Hinweise sorgfältig durch.  
Heben Sie diese Anleitung für den späteren Gebrauch auf.  
Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Ver-  
wenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient  
ein angefeuchtetes Tuch zur Reinigung.  
4.  
Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und  
leicht zugänglich sein.  
5.  
6.  
Das Gerät ist vor Feuchtigkeit zu schützen.  
Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten.  
Ein Kippen oder Fallen könnte Verletzungen hervorrufen.  
7.  
Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät  
vor überhitzung schützt. Sorgen Sie dafür, daB diese Öffnungen  
nicht abgedeckt werden.  
8.  
9.  
Beachten Sie beim. AnschluB an das Stromnetz die AnschluBw-  
erte.  
Verlegen Sie die NetzanschluBleitung so, daB niemand darüber  
fallen kann. Es sollte auch nichts auf der Leitung abgestellt werden.  
10. Alle Hinweise und Warnungen die sich am Geräten befinden sind  
zu beachten.  
11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten  
Sie es vom Stromnetz trennen. Somit wird im Falle einer Überspan-  
nung eine Beschädigung vermieden.  
vii  
12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder  
Flüssigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw.  
elektrischen Schlag auslösen.  
13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der ele-  
ktrischen Sicherheit nur von authorisiertem Servicepersonal geöff-  
net werden.  
14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz  
zu trennen und von einer qualifizierten Servicestelle zu überprüfen:  
a - Netzkabel oder Netzstecker sind beschädigt.  
b - Flüssigkeit ist in das Gerät eingedrungen.  
c - Das Gerät war Feuchtigkeit ausgesetzt.  
d - Wenn das Gerät nicht der Bedienungsanleitung entsprech end  
funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesse-  
rung erzielen.  
e - Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.  
f - Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.  
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil  
1000 beträgt 70dB(A) oder weiger.  
15. VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der  
Batterie.Ersatz nur durch densellben order einem vom Hersteller  
empfohlenemahnlichen Typ. Entsorgung gebrauchter Batterien  
navh Angaben des Herstellers.  
16. ACHTUNG: Es besteht die Explosionsgefahr, falls die Batterie auf  
nicht fachmännische Weise gewechselt wird. Verfangen Sie die  
Batterie nur gleicher oder entsprechender Type, wie vom Hersteller  
empfohlen. Entsorgen Sie Batterien nach Anweisung des Herstell-  
ers.  
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000  
beträgt 70dB(A) oder weiger.  
Haftungsausschluss: Die Bedienungsanleitungen wurden entsprechend  
der IEC-704-1 erstellt. Advantech lehnt jegliche Verantwortung für die  
Richtigkeit der in diesem Zusammenhang getätigten Aussagen ab.  
DISCLAIMER: This set of instructions is given according to IEC704-1.  
Advantech disclaims all responsibility for the accuracy of any statements  
contained herein.  
FPM-3150 Series User Manual  
viii  
Contents  
ix  
Table of Contents  
2
1
Introduction  
This chapter includes:  
• Introduction  
• Specifications  
• LCD Specification  
• Power Consumption  
• Connectors  
• Dimensions  
Chapter 1 Introduction  
1.1 Introduction  
Advantech's FPM-3150G is a 15" color TFT LCD flat panel monitor built  
specifically for industrial applications. With the optional touchscreen,  
FPM-3150G is an excellent and user-friendly system control interface.  
In addition to its usual application as an LCD panel monitor, FPM-3150G  
comes standard with direct VGA control signal input, making it compati-  
ble with Industrial PCs and Workstations. Its OSD (On Screen Display)  
function allows you to adjust display factors such as brightness, contrast,  
colors and VGA signal information. Functions that are more and more  
critical as HMI users become aware of the benefits of flat panel monitors.  
The whole chassis is of stainless steel, and the front panel is of aluminum  
with NEMA4/IP65 compliance.  
FPM-3150G also comes in a touch screen version (FPM-3150G-R). With  
an 8-wire resistive type touchscreen, this monitor can be immediately  
transformed into a remote control system. The Advantech FPM-3150G is  
the ultimate HMI solution for your industrial application.  
1.2 Specifications  
General  
Construction: Heavy-duty aluminum and steel chassis  
Front panel: Aluminum, NEMA4 / IP65 Compliant  
Control: OSD (On Screen Display) control pad on front side  
Mounting: Panel, wall, desktop, VESA ARM or rack (with rackmount  
Dimensions (W x H x D): 422 x 310 x 86 mm (16.6" x 12.2" x 3.4")  
Weight: 6.2 kg (13.7 lb)  
FPM-3150 Series User Manual  
2
     
Touchscreen (Optional)  
Type: 8 wire, analog resistive  
Resolution: 1024 x 1024  
Light Transmission: >80% (Gouge Hardness is greater tahn 4H per  
ASTM D3363-92 for HCC01, HCG10 and HCG12  
Operating Pressure: 30 ~ 45 gram for stylus pen  
contact bounce < 10 ms  
Controller: USB & RS-232 interface  
Power Consumption: +5 V @ 200 mA  
OS Support: Win 95/98/ME/2000/XP/CE/NT/Vista, Linux, MS-DOS  
Life Span: 100 million activation (typical) at a single point with a 5/8"  
diameter silicone finger with a 350 g load at 2 touches per second  
1.3 LCD Specification  
Display Type: XGA TFT LCD  
Display Size: 15"  
Max. Colors: 16.2 M (6 bit + FRC) Full Color  
Max. Resolution: 1024 x 768  
Dot Pitch: 0.297 x 0.297 mm  
View Angle: 140° (V), 120° (H)  
Luminance: 550 cd/m2  
Storage Temperature: -20 ~ 60 ° C  
Operating Temperature: 0 ~ 50 ° C  
Contrast Ratio: 500:1 (typ)  
Lamp Life Time (MTBF): 50,000 hrs.  
1.4 Power Consumption  
Max. Output Power: 48 W  
AC Input Voltage: 100-240 V  
AC  
Output Voltage: + 12 V @ 4 A  
Safety Standards: CE/CCC/FCC/CB  
3
Chapter1  
   
1.5 Connectors  
The following connectors are situated on the left hand side of the  
FPM-3150G Series:  
VGA Port (DB-15)  
This DB-15 connector can be connected to the system via the external  
15-pin DB-15 connector locatd on the left side of the system unit.  
DVI Port (DVI-D)  
Connected with a standard DVI connector thru I/O port of this unit. Only  
supports digital signals  
Touchscreen Connector (DB-9) (optional)  
This connector will be present only if a touchscreen is installed. It must  
be connected to the RS-232 port of the PC. The touchscreen cable is  
included with all orders which include the touchscreen option.  
Touchscreen Connector (USB) (Optional)  
This connector will be present only if a touchscreen is installed. It must  
be connected to the USB port of the PC. The touchscreen cable is  
included with all orders which include the USB touchscreen option.  
Note:  
RS-232 & USB touch screen interface not allow to  
connect into the system at the same time.  
DC 12V Power In  
This connector will be connected to the DC 12V Switching Power  
Supply.  
FPM-3150 Series User Manual  
4
 
1.6 Dimensions  
Figure 1.1: FPM-3150G Dimensions  
5
Chapter1  
   
FPM-3150 Series User Manual  
6
2
2
Mounting  
• Wallmounting  
• Panel Mounting  
• Rack Mounting  
• Desktop Mounting  
• Swing Arm Mounting  
Chapter 2 Mounting  
2.1 Mounting the Monitor  
The FPM-3150G Series can be mounted in many different ways. The  
versatility of the FPM-3150G mounts enable it to be mounted on your  
desk or anywhere else.  
2.1.1 Wall Mounting  
FPM-3150G can be mounted directly on a wall with panel mounting  
brackets. Please refer to figure 2-1 and follow the following steps to  
mount FPM-3150G on a wall:  
1.  
2.  
3.  
Screw the hook and panel-mount brackets on the wall.  
Place the FPM-3150G in the brackets.  
Fix FPM-3150G on the hook and panel-mount bracket..  
Figure 2.1: Wallmounting  
FPM-3150 Series User Manual  
8
       
2.1.2 Panel Mounting  
If you need to install the FPM-3150G series in a panel, please release the  
mounting brackets by detaching four screws on rear side and fix them on  
the top and bottom with screws.  
Panel Mounting  
Brackets  
Figure 2.2: Panel Mounting (396 x 296 mm)  
9
Chapter2  
   
2.1.3 Rack Mounting (Optional)  
If you need to install the FPM-3150G on a rack, you must order the rack  
mount kit for FPM-3150G (Part Number is FPM-3150G-RMKE). Attach  
the two rack mounting brackets on each side of FPM-3150G with 12  
screws, then affix the monitor in the rack.  
Figure 2.3: Rack Mounting Brackets  
FPM-3150 Series User Manual  
10  
   
2.2 Desktop, Swing-ARM for FPM-3150G  
The FPM-3150G Series can be mounted in other ways. These is a desktop  
stand for desktop use and it can also be attached to a swing-arm bracket.  
2.2.1 Desktop Stand  
The panel-mount bracket is attached to the rear of the FPM-3150G to  
become a desktop stand. (Refer to figure 2.4) Simply detach the small  
bracket at the top of the monitor by unscrewing the two screws. The  
lower bracket now becomes a desktop stand bracket.  
Remove the top panel mounting bracket  
that is attached on the rear side of FPM-3150G  
Panel Mounting  
Bracket  
Figure 2.4: Desktop Stand for FPM-3150G  
11  
Chapter2  
     
2.2.2 Swing-ARM (VESA Compliant)  
FPM-3150G has been designed with support for the VESA Arm standard.  
Refer to figure 2.5. Detach the mounting brackets on the rear side, and  
attach the FPM-3150G onto the VESA ARM Mount.  
Figure 2.5: Swing-ARM for FPM-3150G  
FPM-3150 Series User Manual  
12  
   
2
A
Touchscreen  
Appendix A Touchscreen  
A.1 Introduction  
The FPM-3150G Series optional touchscreen uses advanced 8-wire resis-  
tive technology. It provides more accurate sensing capacity than other  
technologies. The touchscreen is specially designed for tough industrial  
environments, and has been approved to FCC Class B standards.  
Note:  
RS-232 & USB touch screen interface not allow to  
connect into the system at the same time.  
A.2 Touchscreen Specifications  
1. Input Method and Activation Force  
1.6mm dia. Delrin stylus : 0.10~0.70N  
16mm dia. Silicon "finger : 0.10~0.80N  
2. Typical Optical Characteristics  
2.1 Visible Light Transmission: >80%  
2.2 Haze:< 13%  
3. Electrical Specifications  
3.1 Operating Voltage: 5.5V or less  
3.2 Contact current: 20mA (maximum)  
3.3 Circuit close resistance: X :300~1000  
Y :200~700  
3.4 Circuit open resistance: > 10M at 25VDC  
3.5 Contact bounce: < 10ms  
3.6 Linear Test : <1.5 %  
3.7 Capacitance:100nF(maximum)  
3.8 Electrostatic Discharge Protection : (per EN 61000-4-2 )  
The touch screen withstands of 15KV air discharge and 8KV  
contact discharge.  
FPM-3150 Series User Manual  
14  
     
4. Linearity  
4.1 Linear Test Specifications  
Direction X: <1.5 %  
Direction Y: <1.5 %  
4.2 Linearity Test  
Apply voltage (DC5V) to upper (or lower ) electrodes, output  
voltage Vx or Vy on the other electrodes is measured at every  
regular intervals.  
Linearity is the value of max. error voltage  
5. Environment Specifications  
5.1 Operating Temperature: -10 ~ + 60° C  
5.2 Storage Temperature: -40 ~ +80° C  
5.3 Humidity: if 40° C, humidity <80% RH  
if 40° C, humidity < 90% RH No dew condensation  
15  
AppendixA  
A.3 Installing Driver for Windows OS  
The touchscreen has drivers for Windows 2000 /XP/2003/Vista. You  
should read the instructions in CD-ROM Disk Touchscreen section care-  
fully before you attempt installation. The FPM-3150G-XCE, RCE need  
to install Penmount 6000 driver. Please find Penmount 6000 folder and  
install the driver into your system.  
Note 1:  
The driver manual are examples only. You must fol-  
low the flow chart instructions and pay attention to  
the instructions which then appear on your screen.  
Note 2:  
Note 3:  
:Note 4:  
The USB & RS-232 cable not allow to connect to  
system at the same time.  
USB & RS-232 interface driver is different, uninstall  
previous driver before installing a different driver.  
If there is any others OS driver need, could down-  
(Penmount 6000)  
FPM-3150 Series User Manual  
16  
 
2
B
Setting Serial Data for  
Expansion  
Appendix B Setting Serial Data for  
Expansion  
B.1 Setting Serial Data for Expansion  
The twelve kinds of timings below are already programmed in this mod-  
ule. The input synchronous signals are automatically recognized.  
Resolution Vertical Frequencies  
56 Hz  
60 Hz  
Pass Fail  
V
70 Hz  
72 Hz  
Pass Fail  
V
75 Hz  
Pass Fail  
V
Pass Fail  
Pass Fail  
640 x 480  
800 x 600  
1024 x 768  
V
V
V
V
V
V
V
V
V
Note 1:  
Even if the preset timing is entered, a little  
adjustment of the functions such as Horizontal  
period, CLK-delay and display position, are  
required. The adjusted values are memorized in  
every preset number.  
Note 2:  
Note 3:  
This module recognizes the synchronous signals  
with near preset timing of the frequency of the  
HS and Vsync, even in the case that the signals  
other than the preset timing that were entered.  
Because adjustments may not fit, such as  
differing magnifying ratios or, in the case that you  
use it except for the display timing that was pre-  
set.  
FPM-3150 Series User Manual  
18  
   
2
C
OSD Operation  
Keypad  
Appendix C OSD Operation Keypad  
C.1 OSD Board Overview  
The OSD keypad, including six keys and a two color indicator, is  
designed as the OSD operation interface  
C.1.1 OSD Button Description  
Buttons  
Power  
Descriptions  
Turn the monitor power ON or OFF.  
Auto/Exit  
Automatically adjust the clock, phase, H-position and  
V-position.  
Exit menu.  
Down/Right/  
Increase  
Activate the volume control.  
Move the selector to the next option.  
Increase the gauge value of the selected option.  
Up/Left/  
Active volume control.  
Decrease  
Move the selector to the previous option.  
Decrease the gauge value of the selected option.  
Menu/Sel  
Source  
Activate the OSD menu.  
Enter/confirm the selected option.  
Changes Input video source  
C.1.2 LED Function  
ON  
Green  
StandBy/OFF  
No Signals  
Green Blinking  
Orange  
FPM-3150 Series User Manual  
20  
       
C.2 OSD Key Functions  
Each selected value is stored into LCD memory after SEL signal input or  
time out. The stored values are not affected if the power is turned off. But  
the selected value is not available in case a selected mode is changed  
before time out or power is turned off before time out. TIME OUT Æ 5-6  
seconds ( Can be set in OSD Manager) The default definition of input  
keys is shown as following:  
C.2.1 Menu Start  
Generate Main Menu  
Press MENU Button in OSD function key  
• Main Menu -- DISPLAY IN SCREEN  
• Sub-Menu – DISPLAY IN SCREEN  
• N/A  
• Available Key Functions  
N/A  
N/A  
N/A  
Select to exit menu or wait for  
time out  
N/A  
N/A  
21  
AppendixC  
   
C.2.2 Input Source Select  
• Generate Main Menu  
Select  
by Left and Right Button, press Menu Button for selection  
confirmation  
• Main Menu -- DISPLAY IN SCREEN  
• Sub-Menu – DISPLAY IN SCREEN  
• Available Key Functions  
Power Off the  
LCD Monitor  
Increase the gauge  
value of the selected  
option.  
Return to last menu  
Selected to confirm  
Decrease the gauge  
value of the selected  
option.  
N/A  
FPM-3150 Series User Manual  
22  
 
4.  
Auto Select Input  
• ON Æ start from default setting and scan the inputs by following  
sequence from ANALOG INPUT, DIGITAL INPUT, S-VIDEO  
INPUT, and CVBS INPUT.  
• OFF Æ start from default setting  
C.2.3 Contrast/ Brightness Setting  
• Generate Main Menu  
Select  
by Left and Right Button, press Menu Button for selection  
confirmation  
• Main Menu -- DISPLAY IN SCREEN  
n
Sub-Menu – DISPLAY IN SCREEN  
23  
AppendixC  
 
• Available Key Functions  
Power Off the  
LCD Monitor  
Increase the gauge  
value of the selected  
option.  
Return to last menu  
Selected to confirm  
Decrease the gauge  
value of the selected  
option.  
N/A  
RECALL VALUE – User Define  
st  
• Rec1 Æ Pressed to record 1 setting as recall value followed by current  
screen setting  
nd  
• Rec2 Æ Pressed to record 2 setting as recall value followed by cur-  
rent screen setting  
• Recall Æ Switch the setting change by Rec1 and Rec2 while pressed  
C.2.4 Geometry Menu – For DVI Input  
• Generate Main Menu  
Select  
by Left and Right Button, press Menu Button for selection  
confirmation  
• Main Menu -- DISPLAY IN SCREEN  
• Sub-Menu – DISPLAY IN SCREEN  
FPM-3150 Series User Manual  
24  
 
• Available Key Functions  
Power Off the  
LCD Monitor  
Increase the gauge value  
of the selected option.  
Return to last menu  
Selected to confirm  
N/A  
Decrease the gauge  
value of the selected  
option.  
25  
AppendixC  
C.2.5 Color Temperature Menu  
• Generate Main Menu  
Select  
by Left and Right Button, press Menu Button for selection  
confirmation  
• Main Menu -- DISPLAY IN SCREEN  
• Sub-Menu – DISPLAY IN SCREEN  
• Available Key Functions  
Power Off the  
LCD Monitor  
Increase the gauge  
value of the selected  
option.  
Return to last menu  
Selected to confirm  
Decrease the gauge  
value of the selected  
option.  
N/A  
FPM-3150 Series User Manual  
26  
 
C.2.6 RGB Color Menu  
• Generate Main Menu  
Select  
by Left and Right Button, press Menu Button for selection  
confirmation  
Select  
by Left and Right Button, Press Menu  
Button for selection confirmation  
• Main Menu -- DISPLAY IN SCREEN  
• Sub-Menu – DISPLAY IN SCREEN  
• Sub-Menu – DISPLAY IN SCREEN  
27  
AppendixC  
 
• Available Key Functions  
Power Off the  
LCD Monitor  
Increase the gauge value  
of the selected option.  
Return to last menu  
Selected to confirm  
N/A  
Decrease the gauge  
value of the selected  
option.  
Customization setting for RGB colors  
C.2.7 Language Menu  
• Generate Main Menu  
Select  
by Left and Right Button, press Menu Button for selection  
confirmation  
• Main Menu -- DISPLAY IN SCREEN  
• Sub-Menu – DISPLAY IN SCREEN  
FPM-3150 Series User Manual  
28  
 
• Available Key Functions  
Power Off the  
LCD Monitor  
Increase the gauge value  
of the selected option.  
Return to last menu  
Selected to confirm  
N/A  
Decrease the gauge  
value of the selected  
option.  
C.2.8 OSD Manager  
• Generate Main Menu  
Select  
by Left and Right Button, press Menu Button for selection  
confirmation  
• Main Menu -- DISPLAY IN SCREEN  
• Sub-Menu – DISPLAY IN SCREEN  
29  
AppendixC  
 
• Available Key Functions  
Power Off the  
LCD Monitor  
Increase the gauge value  
of the selected option.  
Return to last  
menu  
Selected to confirm  
N/A  
Decrease the  
gauge value of the  
selected option.  
C.2.9 Auto Configuration Menu  
• Generate Main Menu  
Select  
by Left and Right Button, press Menu Button for selection  
confirmation  
• Main Menu -- DISPLAY IN SCREEN  
• Sub-Menu – DISPLAY IN SCREEN  
FPM-3150 Series User Manual  
30  
 
• Available Key Functions  
Power Off the  
LCD Monitor  
Increase the gauge  
value of the selected  
option.  
Return to last menu  
Selected to confirm  
Decrease the gauge  
value of the selected  
option.  
N/A  
Auto configuration can be set in menu and also can press the  
without any menu indication.  
C.2.10 Mode Information Menu  
• Generate Main Menu  
Select  
by Left and Right Button, press Menu Button for selection  
confirmation  
• Main Menu -- DISPLAY IN SCREEN  
• Sub-Menu – DISPLAY IN SCREEN  
31  
AppendixC  
 
• Available Key Functions  
Power Off the  
LCD Monitor  
Increase the gauge value  
of the selected option.  
Return to last  
menu  
Selected to confirm  
N/A  
Decrease the  
gauge value of the  
selected option.  
C.2.11 Memory Recall Menu  
• Generate Main Menu  
Select  
by Left and Right Button, press Menu Button for selection  
confirmation  
• Main Menu -- DISPLAY IN SCREEN  
• Sub-Menu – DISPLAY IN SCREEN  
FPM-3150 Series User Manual  
32  
 
• Available Key Functions  
Power Off the  
LCD Monitor  
Increase the gauge  
value of the  
selected option.  
Return to last menu  
Selected to confirm  
Decrease the gauge  
value of the selected  
option.  
N/A  
C.2.12 Exit Menu  
• Generate Main Menu  
Select  
by Left and Right Button, press Menu Button for selection  
confirmation  
• Main Menu -- DISPLAY IN SCREEN  
• Sub-Menu – DISPLAY IN SCREEN  
33  
AppendixC  
 
• Available Key Functions  
Power Off the  
LCD Monitor  
Increase the gauge  
value of the selected  
option.  
Return to last menu  
Selected to confirm  
Decrease the gauge  
value of the selected  
option.  
N/A  
C.2.13 Hot Keys  
OSD LOCK/UNLOCK  
HOT KEYS  
Press  
first then press  
for change this setting, Followed  
this sequence for the button press so that you can have OSD LOCK and  
UNLOCK setting  
Entry OSD LOCK MODE  
Press HOT KEY, the screen will show this action first  
• Don’t remove the HOT KEY until the screen indicated this task is fin-  
ished.  
FPM-3150 Series User Manual  
34  
 
• Entry OSD UNLOCK MODE  
• Press HOT KEY, the screen will show this action first  
• Don’t remove the HOT KEY until the screen indicated this task is fin-  
ished.  
35  
AppendixC  
FPM-3150 Series User Manual  
36  

HP Hewlett Packard Hewlett Packard Computer Monitor W1907 User Manual
HP Hewlett Packard Hewlett Packard Computer Monitor W185Q User Manual
Hotpoint Cooktop 52TCK User Manual
Hanns G Computer Monitor HZ231 User Manual
GE JTP70CM User Manual
Electrolux EHG675 User Manual
Blodgett SC 6DS User Manual
Black Box Computer Hardware LEH1008A 2SFP User Manual
Bakers Pride Oven 151 User Manual
Acer 3230 User Manual