Acer H235H User Manual

Acer H235H

Service Guide

Transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in

any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without

the prior written permission of Acer Incorporated.

Disclaimer

The information in this guide is subject to change without notice. Acer Incorporated makes no representations or

warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties

of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is

sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer

Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any

incidental or consequential damages resulting from any defect in the software.

Intel is a registered trademark of Intel Corporation.

Pentium and Pentium II/III are trademarks of Intel Corporation.

Other brand and product names are trademarks and/or registered trademarks of their respective holders.

Trademarks

Acer is a registered trademark of Acer Incorporated.

All other trademarks are property of their respective owners.

Conventions

The following conventions are used in this manual:

Screen messages

Note

Denotes actual messages that appear on screen.

Gives bits and pieces of additional information related to the current topic.

Alerts you to any damage that might result from doing or not doing specific actions.

Gives precautionary measures to avoid possible hardware or software problems.

Remind you to do specific actions relevant to the accomplishment of procedures.

Warning

Caution

Important

Preface

Before using this information and the product it supports, please read the following general information.

1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided

for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness,

your regional office may have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra

memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such

cases, please contact your regional offices or the responsible personnel/channel to provide you with further

technical details.

2. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on

your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the

printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a

DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list

provided by your regional Acer office to order FRU parts for repair and service of customer machines.

Warning: (For FCC Certified Models)

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment.

2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.

3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this

equipment. It is the responsibility of the user to correct such interference.

As ENERGY STAR^®Partner our company has determined that this product meets the ENERGY STAR^®

guidelines for energy efficiency.

Warning:

To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerous high voltages are present

inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.

Precautions

z Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in

a wet basement.

z Do not place the monitor on an unstable trolley, stand, or table. If the monitor falls, it can injure a person and

cause serious damage to the appliance. Use only a trolley or stand recommended by the manufacturer or sold

with the monitor. If you mount the monitor on a wall or shelf, uses a mounting kit approved by the manufacturer

and follow the kit instructions.

z Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable

operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered.

Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radiator

or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided.

z The monitor should be operated only from the type of power source indicated on the label. If you are not sure of

the type of power supplied to your home, consult your dealer or local power company.

z The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit

only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug,

have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the

safety purpose of the grounded plug.

Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the

monitor from damage due to power surges.

z Do not overload power strips and extension cords. Overloading can result in fire or electric shock.

z Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric

shock. Never spill liquids on the monitor.

z Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous

voltages and other hazards. Please refer all servicing to qualified service personnel

z To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate

configured receptacles marked between 100 - 240V AC, Min. 5A.

z The wall socket shall be installed near the equipment and shall be easily accessible.

Special Notes on LCD Monitors

The following symptoms are normal with LCD monitor and do not indicate a problem.

Notes

z Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and

then turn it on again to make sure the flicker disappears.

z You may find slightly uneven brightness on the screen depending on the desktop pattern you use.

z The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a

missing pixel or a pixel lit all of the time.

z Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image,

when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image

or turning off the Power Switch for hours.

Table Of Contents

Chapter 1

Monitor Features

…………………………………………

Introduction

………………………………………

……………………………………..

………………………………………

Electrical Requirements

LCD Monitor General Specification

LCD Panel Specification

Factory Preset Timing

Monitor Block Diagram

Main Board Diagram

Power Board Diagram

Software Flow chart

Main Board Layout

Installation

Chapter 2

Operating Instructions

………………………………………

User Controls

………………………………………

Front Panel Controls

eColor Management (OSD)

How to Adjust a Setting

How To Optimize The DOS-Mode

Enter into the factory mode

Chapter 3

Machine Disassembly

………………………………………

Chapter 4

Chapter 5

Troubleshooting

………………………………………

Connector Information

Chapter 6

Chapter 7

FRU (Field Replacement Unit) List

………………………………………

Exploded Diagram

………………………………………

Schematic Diagram

………………………………………

Monitor Features

Chapter 1

Introduction

Scope

This short specification describes the electrical, optical and functional performance requirements for a 63.2cm (23.6”)

TFT LCD color monitor with VGA&DVI compatible interface.

Description

The LCD monitor is designed with the latest LCD technology to provide a performance oriented product with no

radiation. This will alleviate the growing health concerns. It is also a space saving design, allowing more desktop

space, and comparing to the traditional CRT monitor, it consumes less power and gets less weight in addition MTBF

target is 50k hours or more.

Chart of H235H

Panel

LTM230HT01 A03(003) SZ SEC

Signal Interface

Sync Type

D-Sub 15pin;DVI 24pin;HDMI

Separate / Compatible

Color Temp User Adjust

DDC

Support

DDC2B

Yes

Speaker

Headphone Jack

Microphone Jack

USB Hub

Yes

Tilt / Swivel

Yes /No

Electrical Requirements of H235H

Standard Test Conditions

All tests shall be performed under the following conditions, unless otherwise specified.

Warm up time

AC supply voltage

Ambient temperature

Humidity

＞ 30 min.

230V± 5％, 50± 3 Hz

20°C ± 5°C

65% ± 20%

Display mode

e-color mode

1920 x 1080, 60 Hz, Pixel Clock：148.5MHZ,all white

Set to “User” mode

Set to The value under user mode, which allows that the brightest

two of 32 linear distributed gray-scales (0～ 700mv) can be

distinguished.

Contrast control

Color temperature

Brightness control

Analog Input signal

Picture position and size

Viewing angle

6500°K

The value under user mode

700 mVss

Factory preset value,

90 ° H and V

Viewing distance

40 cm for LCD performance, 20 cm for LCD failures

Dark room < 1 cd/m2

Ambient illumination

Measurement systems

The units of measure stated in this document are listed below:

1 gamma = 1 nano tesla

1 tesla = 10,000 gauss

cm = in x 2.54

Lb = kg x 2.2

Degrees F = [°C x 1.8] + 32

Degrees C = [°F - 32]/1.8

u' = 4x/(-2x + 12y + 3)

v' = 9y/(-2x + 12y + 3)

x = (27u'/4)/[(9u'/2) - 12v' + 9]

y = (3v')/[(9u'/2) - 12v' + 9]

nits = cd/(m2) = Ft-L x 3.426

lux = foot-candle x 10.76

LCD Monitor General Specification

See the image on

next page.

55.2

6.45

17.2

27.0

LCD Panel Specification of H235H

LTM230HT01 is a color active matrix liquid crystal display (LCD) that uses amorphous silicon TFT (Thin Film

Transistor) as switching components. This model is composed of a TFT LCD panel, a driver circuit and a back light

unit. The resolution of a 23” is 1920 x 1080 and this model can display up to 16.7 millions colors.

General Specifications

Block Diagram

TFT LCD Module

Electrical Characteristics

Optical Specifications

Factory Preset Timing of H235H

Monitor Block Diagram

The LCD MONITOR will contain a main board, a power board, and a key board which house the flat panel control

logic, brightness control logic and DDC.

The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips

each voltage.

Flat Panel and

CCFL backlight

CCFL Drive.

Main Board

Power Board

AC-IN

100V-240V

Key board

HDMI Signal

DVI Signal

D-SUB Signal

Main Board Diagram

Crystal 12MHz

(X401)

Panel Interface

(CN404)

Audio Digital-to-Analog

converter

PCM1754DBQR

(U601)

Scalar IC TSUMO58GDJ-LF

Key control Interface

(CN401)

PC_INL

PC_INR

(Include MCU, ADC, OSD)

(U401)

HDMI_INL

HDMI_INR

Audio Power Amplifier

TA6019A4

Flash Memory

EN25F20

(U402)

(U603)

H sync

V sync

RGB

D-Data

D-Clock

Audio Output

interface

EEPROM

M24C02

(U406)

EEPROM

M24C02

(U405)

EEPROM

M24C02

(U503)

(CN602)

Phone Jack

(CN605)

DVI

Connector

(CN403)

D-Sub

Connector

(CN402)

HDMI

Connector

(CN501)

Power Board Diagram

16V

AC input

EMI filter

Bridge

Rectifier

and Filter

Rectifier

diodes

Transformer

Start Resistor

(R904, R905)

Feedback

Circuit

PWM Control

(IC901)

Power Switch

(Q901)

Photo coupler

(IC903)

Output

Transformer

(PT801)

MOSFET

(Q805,Q806)

16V

Circuit

Lamp

PWM Control

Feedback

Circuit

TA9687GN

(IC801)

ON/OFF

DIM

Software Flow Chart

Remark:

1) MCU initializes.

2) Is the EEPROM blank?

3) Program the EEPROM by default values.

4) Get the PWM value of brightness from EEPROM.

5) Is the power key pressed?

6) Clear all global flags.

7) Are the AUTO and SELECT keys pressed?

8) Enter factory mode.

9) Save the power key status into EEPROM.

Turn on the LED and set it to green color.

Scalar initializes.

10) In standby mode?

11) Update the lifetime of back light.

12) Check the analog port, are there any signals coming?

13) Does the scalar send out an interrupt request?

14) Wake up the scalar.

15) Are there any signals coming from analog port?

16) Display "No connection Check Signal Cable" message. And go into standby mode after the

message disappears.

17) Program the scalar to be able to show the coming mode.

18) Process the OSD display.

19) Read the keyboard. Is the power key pressed?

Main Board Layout

Symbol Description

Symbol

U601

Description

U401

U402

X401

U405

IC TSUMO58GDJ-LF-1

IC PCM1754DBQR SSOP-16

IC PA6019A4

IC EN25F20-100GCP

14.31818MHZ/32PF/49US0

M24C02-WMN6TP

U603

CN401

CN402

WAFER

D-SUB 15PIN

U406

U503

M24C04-WMN6TP

M24C02-WMN6TP

CN403

CN501

DVI 24PIN CONN F

HDMI HEADER 19P +SCREW HOLE

Installation

To install the monitor on your host system, please follow the steps below:

Steps

1 Connect the video cable

a Make sure both the monitor and computer are switched off.

b Connect the VGA video cable to the computer.

c Connect the digital cable (only for dual-input models).

(1) Make sure both the monitor and computer are switched off.

(2) Connect one end of the 24-pin DVI* cable to the back of the

monitor and the other end to the computer's port.

(3) Connect one end of the 19-pin HDMI* cable to the back of the

monitor and the other end to the computer's port.

2 Connect the power cord

Connect the power cord to the monitor, then to a properly grounded AC

outlet.

3 Turn on the monitor and computer

Turn on the monitor first, then the computer. This sequence is very

important.

4 If the monitor does not function properly, please refer to the

troubleshooting section to diagnose the problem

Attaching the Base

1 Attach the monitor stand arm to the base.

2 Ensure that the base is locked onto the monitor stand arm.

SCREEN POSITION ADJUSTMENT

To optimize the viewing position, you can adjust he monitor tilt, using both of your hands to hold

the edges of the monitor. The monitor can be adjusted to 15 degrees up or 5 degrees down.

connecting the power cord

• Check first to make sure that the power cord you use is the correct type required for your area.

• The monitor has a universal power supply hat allows operation in either 100/120 V AC r 220/240 V AC voltage area.

No user adjustment s required.

• Plug one end of the power cord to the AC inlet, and plug the other end into an AC outlet.

• For units using 120 V AC:Use a UL-listed cord set, type SVT wire and plug rated 10 A/125 V.

• For units using 220/240 V AC:Use a cord set consisting of H05VV-F cord and plug rated 10 A/250 V. The

cord set should have the appropriate safety approvals for the country in which the equipment will be installed.

Chapter 2

Operating Instructions

Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the

monitor. By changing these settings, the picture can be adjusted to your personal preferences.

• The power cord should be connected.

• Connect the video cable from the monitor to the video card.

• Press the power button to turn on the monitor position. The power indicator will light up.

Front panel controls

How to Adjust a Setting

How to Optimize The DOS-Mode

Plug And Play

Plug & Play DDC2B Feature

This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the

monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional

information about its display capabilities.

The DDC2B is a bi-directional data channel based on the I²C protocol. The host can request EDID information over

the DDC2B channel.

This monitor will appear to be non-functional if there is no video input signal. In order for this monitor to

operate properly, there must be a video input signal.

This monitor meets the Green monitor standards as set by the Video Electronics Standards Association (VESA)

and/or the United States Environmental Protection Agency (EPA) and The Swedish Confederation Employees

(NUTEK). This feature is designed to conserve electrical energy by reducing power consumption when there is no

video-input signal present. When there is no video input signals this monitor, following a time-out period, will

automatically switch to an OFF mode. This reduces the monitor's internal power supply consumption. After the video

input signal is restored, full power is restored and the display is automatically redrawn. The appearance is similar to

a "Screen Saver" feature except the display is completely off. Pressing a key on the keyboard, or clicking the mouse

restores the display.

Using the Right Power Cord

The accessory power cord for the Northern American region is the wallet plug with NEMA 5-15 style and is UL listed

and CSA labeled. The voltage rating for the power cord shall be 125 volts AC.

Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of

a minimum No. 18 AWG, type SJT or SVT three conductors flexible cord. One end terminates with a grounding type

attachment plug, rated 10A, 250V, and CEE-22 male configuration. The other end terminates with a molded-on type

connector body, rated 10A, 250V, having standard CEE-22 female configuration.

Please note that power supply cord needs to use VDE 0602, 0625, 0821 approval power cord in European counties.

Enter into the factory mode:

Turn off the power, press the “power” button to turn on monitor, keep pressing the “power” button simultaneity press

the fifth button ,The factory OSD will be on the panel.

Chapter 3

Machine Disassembly

This chapter contains step-by-step procedures on how to disassemble the monitor-

H235H for maintenance.

The tool for disassembly is as follows:

Screwdriver, Hexagonal screwdriver, Putty knife.

Disassembly Procedure

1.Lay the monitor on a flat, soft and clean surface.

2. Remove the screw remarked in red to remove base,

3.Remove the rear cover and bezel.

(1) .Remove the rear cover

(2)Pry the monitor up then find out the hooks’ position, use the tool (like the picture or other card) to insert into the

gap of bezel and rear cover

Turn over the monitor and take off the rear cover.

(3)Remove the four screws remarked in red to remove the hinge,

(4)Disconnected the connector remarked in green to remove the bezel.

PS: be careful to Disconnect the Key board connector, because the keyboard connector maybe damage.

Key board

install: The audio

cable should be

layout as show

4. Remove the lamp connectors and the LVDS cable to remove the panel.

LVDS cable

5. Remove the five screws remarked in red.

6. Remove the five screws remarked in red and disconnected remarked in green to remove the main board and

power board.

Main board

Power board

7.The panel

Chapter 4

Troubleshooting

This chapter provides troubleshooting information for the H235H:

1. No Power

No power

Press power key and look if the

picture is normal

Please reinsert and make sure the

AC of 100-240 is normal

Reinsert or check the

power section

Measure U104 Pin2=1.8V, U103 PIN2=3.3V

Check CN101,U104 and U103

Check if X401 oscillate waveforms are

normal

Replace X401

Replace U401

2. No Picture (LED is orange)

No picture

The button if under

control

X401 oscillate

waveform is normal

Replace X401

Check reset circuit of

U401 is normal

Check Correspondent

component

Measure U104 Pin2=1.8V,

U103 PIN2=3.3V

Replace U401

X401 oscillate

waveform is normal

Check CN101, U104 and U103

Replace X401

Check HS/VS from

CN402 is normal

Check Correspondent

component

Replace U401

3. Panel Power Circuit

White screen

Measure Q106 base

is low level?

X401 oscillate

waveform is normal

Replace X401

Check CN404 is solder

and Q106, Q104 is OK?

Check reset circuit of

U401 is normal

Check Correspondent

component.

Check Correspondent

component.

Replace U401

Replace PANEL

4. Key Board

OSD is unstable or not working

Is Key Pad Board connecting normally?

Connect Key Board

Replace Button Switch

Replace Key Board

Is Button Switch normally?

Is Key Pad Board normally?

Check Main Board

5. Power Board

1) No power

Check CN902 PIN3, 4 = 5V

Check AC line volt 110V or 220V

Check AC input

Check the voltage of C905 (+)

Check bridge rectified circuit and F901 circuit

Check start voltage for the pin3 of IC901

Check R904, R905 and Change IC901

Check the auxiliary voltage is bigger than

11V and smaller than 25V

1) Check IC901

2) Check R909/D901/C908/C907circuit

Check IC901 pin8 PWM wave

Check IC901

Check D906/D907/D908/IC903/Q903/ZD902

2.) No Backlight

Check if the input voltage of inverter part is 16V

Check adapter part

Check ON/OFF signal

Check Interface board

Check IC801 PIN10=16V

Check ON/OFF circuit

Check IC801 PIN5 have triangle wave

Change IC801

Check IC801 PIN8/PIN9 PWM wave

Check Q805/Q806/IC801

Check the output of PT801

Change PT801

Check connecter & lamp

Chapter 5

Connector Information

D-sub connect and DVI connect:

15-Pin Color Display Signal Cable

24-Pin Color Display Signal Cable

19-pin color display signal cable

Chapter 6

FRU (Field Replaceable Unit) List

This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of H235H. Refer to this

chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).

NOTE: Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information

available on your regional web or channel (http://aicsl.acer.com.tw/spl/). For whatever reasons a part number

change is made, it will not be noted in the printed Service Guide. For ACER AUTHORIZED SERVICE

PROVIDERS, your Acer office may have a DIFFERENT part number code from those given in the FRU list of

this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order

FRU parts for repair and service of customer machines.

NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on

how to dispose it properly, or follow the rules set by your regional Acer office on how to return it.

Exploded Diagram (Model: H235H)

Item

Description

BEZEL

TPV Part No.

ACER Part NO.

Q`ty

A34G1361AGBA1B0130

60.LHF0B.003

POWER MYLAR

POWER BUTTON

LED MYLAR

LED COVER

MAIN FRAME

BASE ASS'Y

REAR COVER

CABLE COVER

IO COVER

Q05G6104

A33G0714BDZ 1L0100

Q05G6104

A33G0713AGC 1L0100

A15G0820101

60.LHF0B.006

60.LHF0B.005

60.LHF0B.004

Q37G0151011

A34G1362AEOA1M0100

A33G0715AGB 1X0100

A34G1365AGB 1B0100

0G1G1130 8120

SCREW

SCREW,42-D020523

SCREW

0M1G1730 6120

0Q1G 930 8 47 CR3

0M1G 140 6125

SCREW

Part List

Above picture show the description of the following component.

Picture

Description

TPV Part No.

ACER Part NO.

60.LHF0B.006

Main_frame

A15G0820101

Bezel

A34G1361AGBA1B0130

60.LHF0B.003

Panel

750GLG230F1A33N000

LK.23006.001

Power Board

PWPC9D41EQKP

55.LHF0B.002

Main Board

CBPCRA6ABQ4

55.LHF0B.001

Q37G0151011

BASE ASS'Y

60.LHF0B.005

A34G1136AEM 1B0130

Rear cover

A34G1362AEOA1M0100

60.LHF0B.004

Chapter 7

Schematic Diagram

Main Board

+5V

VCC3.3

4,5,7 +5V

C102

470uF/16V

R101

10K 1/16W 5%

C101

0.1uF 16V

U101

NC/AP1117D33LA

R102

1K 1/16W 5%

Adj_BACKLIGHT

TO252

VCC3.3

C119

DIM

ON/OFF

R103

10K 1/16W 5%

+5V

VCC3.3

R104

10K 1/16W 5%

4,5,7 +5V

VCC3.3 5,7

VIN

VOUT

+5V_USB

C103

0.1uF 16V

R105 10K 1/16W 5%

C106

0.1uF 16V

U103

AP1117E33LA

C107

0.1uF 16V

on_BACKLIGHT

Q101

2N3904S-RTK/PS

C105

100uF/16V

+5V_USB

SOT223

C116

470uF/16V

C115

0.1uF 16V

SOT223

TO252

U105 NC/AIC1117A-18PY

VIN

VOUT

AZ1117D-1.8-E1

CN101

CONN

Vin

Vout

+5V

U104

VLCD

D510

R110

VCC1.8

R111

10K 1/16W 5%

SM340A

VLCD

R112

10K 1/16W 5%

U102

Q104

AO3401

VCC1.8

OUT

R113

56K 1/16W 5%

C117

R114 10K 1/16W 5%

+5V

C110

Q106

2N3906S-RTK/PS

C111

0.22uF

470uF/16V

C112

0.1uF 16V

C109

100uF/16V

0.1uF 16V

on_Panel

R116

TO263

NC/AIC1084-18PM

T P V ( Top Victory Electronics Co . , Ltd. )

OEM MODEL

Size

Rev

acer H235H

715G3266-E

G3266-1B-X-X-3-090512

TPV MODEL

絬

隔

瓜

絪

腹

Key Component

Date

2.0.POWER

PCB NAME

Sheet

称爹>

称爹

Tuesday , May 12, 2009

FB406

FB407

FB408

30 OHM

DB15

RED+

RED-

GREEN+

GREEN-

BLUE+

BLUE-

R454

R455

R456

R457

56 OHM 1/16W

470R 1/16W 5%

C440 0.047uF

C441 0.047uF

C442 0.047uF

C443 1000pF

RIN

GIN

BIN

30 OHM

PC5V

VGA_CON

SOG

CN402

R460

R461

R462

100R 1/16W 5%

C444 0.047uF

C445 0.047uF

C446 0.047uF

GNDR

GNDG

GNDB

D404

D405

D406

BAV99

ESD_5V

PC5V

ZD403

BAV99

D428

RLZ5.6B

C447

0.1uF 16V

C449

0.1uF 16V

LL4148

C448

0.1uF 16V

DET_VGA

+5V

PC5V

DET_VGA

C645

0.1uF 16V

3,5,7 +5V

HSI

VSI

FB409

120 OHM

R466

R469

470R 1/16W 5%

R467

D407

BAV70

HSYNC

VSYNC

1K 1/16W 5%

ZD408

ZD409

ZD410

R468

C450

C451

RLZ5.6B

2K2 1/16W 5% 22pF

2K2 1/16W 5%

47pF

C452

U405

0.22uF

VCC A0

SCL_VGA

SDA_VGA

R473

R474

100R 1/16W 5%

SCL A2

SDA VSS

R495

M24C02-WMN6TP

DDC_WP

DDCA_SDA

DDCA_SCL

DET_VGA_5V

ZD411

ZD412

RLZ5.6B

10K 1/16W 5%

C469

+5V

DVI5V

20K 1/10W

CN403

VSYNC

SYNC GND

DDC SCL

DDC SDA

+5V

DET_DVI

DVI5V

R478

DET_DVI

SCL_DVI

SDA_DVI

DVI5V

R476

R477

100R 1/16W 5%

D413

BAV70

DVI5V

+5V

1K 1/16W 5%

HPD

R479

Q407

DVI_HPD

1/3shield

2/4shield

0/5shield

clk shield

R480

ZD414

ZD415

RLZ5.6B

ZD416

ZD417

C453

C454

0.22uF

U406

FB411

300 OHM

RLZ5.6B

0.1uF 16V

VCC A0

WP A1

SCL A2

SDA VSS

DAT0+

DAT0-

DAT1+

DAT1-

DAT2+

DAT2-

R484

R485

R486

R487

R488

R489

10R 1/16W 5%

RX0+

RX0-

RX1+

RX1-

RX2+

RX2-

DAT0+

DAT0-

DAT1+

DAT1-

DAT2+

DAT2-

DAT3+

DAT3-

DAT4+

DAT4-

DAT5+

DAT5-

clk+

M24C02-WMN6TP

DVI_SDA

DVI_SCL

R490

DDC_WP

1K 1/16W 5%

5V_EMI 7

DCLK+

DCLK-

R492

R493

10R 1/16W 5%

C467

0.1uF 16V

RXC+

RXC-

clk-

ESD_5V

JACK

ZD418

D419

D420

D421

BAV99

C458

D422

D423

D424

BAV99

C461

D425

D426

BAV99

RLZ5.6B

BAV99

C456

BAV99

C457

BAV99

C460

BAV99

C455

C459

C462

T P V ( Top Victory Electronics Co . , Ltd. )

OEM MODEL

TPV MODEL

Size

Rev

acer H235H

715G3266-E

0.1uF 16V

G3266-1B-X-X-3-090512

絬

隔

瓜

絪

腹

Key Component

Date

3.0.INPUT

PCB NAME

Sheet

称爹>

称爹

Tuesday, May 12, 2009

AVDD_33

VDDP

AVDD_18 AVDD_MEMPLL_33

VDDC

103

VCC3.3

VDDP

VCTRL

FB402

VCC3.3 FB401 AVDD_MEMPLL_33

RIN

GNDR

GIN

GNDG

SOG

BIN

3,7 VCC3.3

RIN0P

RIN0M

GIN0P

GIN0M

SOGIN0

BIN0P

BIN0M

HSYNC0

VSYNC0

DDCA_SDA/RS232_TX

DDCA_SCL/rs232_RX

120 OHM

PA[0..9]

C404

C405

C406

C407

C408

C409

C410

C411

PA[0..9]

PA0

PA1

PA2

PA3

PA4

PA5

PA6

PA7

PA8

PA9

120 OHM

C402

10uF/16V

LVA3P

LVA3M

LVACKP

LVACKM

LVA2P

LVA2M

LVA1P

LVA1M

LVA0P

LVA0M

C403

0.1uF 16V 0.1uF 16V 0.1uF 16V 0.1uF 16V 0.1uF 16V 0.1uF 16V 0.1uF 16V 0.1uF 16V

0.1uF 16V

GNDB

HSYNC

VSYNC

DDCA_SDA

DDCA_SCL

B+

B-

G+

G-

R+

R-

RX2P

RX2N

RX1P

RX1N

RX0P

RX0N

RXCKP

RXCKN

DDCD_SDA

DDCD_SCL

PB[0..9]

VCC1.8 FB403

AVDD_18

PB[0..9]

100

PB0

LVB3P

LVB3M

LVBCKP

LVBCKM

LVB2P

LVB2M

LVB1P

LVB1M

LVB0P

LVB0M

PB1

PB2

PB3

PB4

PB5

PB6

PB7

PB8

PB9

CLK+

CLK-

120 OHM

C413

DDCD_SDA

DDCD_SCL

C412

10uF/16V

0.1uF 16V

VCC1.8

FB404

VDDC

R405

390 OHM 1/16W

+5V

VCC3.3

AVDD_33

VCC1.8

REXT

120 OHM

C415

C416

C417

C418

TSUMO58GDJ-LF-1

R554

R556

C414

10uF/16V

REFP

REFM

VCC3.3

C423

0.1uF 16V 0.1uF 16V 0.1uF 16V 0.1uF 16V

0R05 1/16W

+5V

VCC3.3

0.1uF 16V

VCC3.3

POWER

R555

R553

GPIO_P14/PWM0

P24 SPDIF Output

+5V

0R05 1/16W

Volume

U402

EN25F20-100GCP

GPIO_P22/PWM1

GPIO_P24/PWM2

C425

0.22uF

R406

SPDIF_OUT

VDD

SDO

SCZ

SCK

SDI

109

on_PANEL

on_BACKLIGHT

HOLD# CE#

GPIO_P04/PWM3

GPIO_P25/PWM3

WP#

VSS

SCK

SDI

VCC3.3 FB405

AVDD_33

Q402

2N3906S-RTK/PS

DET_INPUT

KEY1

KEY2

119

120

121

122

123

124

125

R524

R415

R417

R414

R419

R420

100R 1/16W 5%

22K 1/16W 5%

DET_INPUT

HDMI_HPD

GPIO_P00/SAR0

GPIO_P01/SAR1

GPIO_P02/SAR2

GPIO_P03/SAR3

GPIO_P06

GPIO_P07

GPIO_P13/PWM2

LED_G

120 OHM

R408

220R 1/16W 5%

C420

C421

+5V

R418

10K 1/16W 5%

108

DET_5V

C419

0.1uF 16V

C465

10uF/16V

RST

0.1uF 16V 0.1uF 16V

Q403

2N3906S-RTK/PS

LED_A

R413

470R 1/16W 5%

adj_BACKLIGHT

C401

XIN

128

127

102

XI N

GPIO_P15

GPIO_P16

10uF/16V

+5V

DVI_HPD

VCC3.3

+5V

XOUT

XOU T

BYPASS

10K 1/16W 5%

R576

R423

R422

10K 1/16W 5%

R424

R425

C428

U403

VCC

SCL

DET_5V

C429

EE_WP R426

R427

4K7 1/16W 5%

R577

VDDP

I2C_MCL

I2C_MDA

0.1uF 16V

R428

BAT54C

D429

SDA

GND

R429

MODE

+5V

R565

1K 1/16W 5%

R566

1K 1/16W 5%

+5V 3,4,7

R432

10K 1/16W 5%

R440

22KOHM1/16W

R448

10K 1/16W 5%

Q408

2N3906S-RTK/PS

R445

C466

100uF/16V

47KOHM1/16W

VOL

MUTE

R450

Volume

Q404

2N3904S-RTK/PS

C439

1uF/16V

AUDIO_MUTE

R452

Q406

2N3904S-RTK/PS

R447

4K7 1/16W 5%

VDDP

114

VDDP

C427

C430

C431

C432

0.1uF 16V 0.1uF 16V 0.1uF 16V 0.1uF 16V

1K 1/16W 5%

CN405

VCC3.3

POWER

AUMCKO

AUOUTLR

MCKO

AUOUTLR

AUSCK

AUSDO

AUMUTE/GPIO_P43

SPDIFO/GPIO_P42

R531

KEY_LEFT

KEY_RIGHT

KEY_AUTO

KEY1

KEY2

R532

R533

R534

AUSCK

AUSDO

AUMUTE

GPO_P42

GPO_P43

LED_A

LED_G

CEC_CTRL

110

111

115

116

117

118

AUDIO_MUTE

VCC3.3

GPIO_00

GPIO_02

GPIO_01

SW_AUOUT

DET_VGA_5V

KEY1

KEY2

POWER

LED_G

LED_A

NC/CONN

C639

0.1uF 16V

R638

GPIO_06

GPIO_P26/PWM0

GPIO_P27/PWM1

GPIO_07

GPIO_08

GPIO_09

GPIO_10

EE_WP

POWER

R574

56K 1/16W 5%

C424

56PF50V

R409

X401

22R 1/16W 5%

220R 1/16W 5%

XI N

Q507

HDMI_SEL

AO3401

Sensor_INT

Sensor_SCL

Sensor_SDA

14.3 Mhz

C426

56PF50V

XOU T

R411

R567

R568

R569

100R 1/16W 5%

Sensor_SDA

Sensor_SCL

Sensor_INT

LED_G

KEY1

CN401

CN407 CONN

CONN

T P

(

Top Victory Electronics Co

G3266-1B-X-X-3-090512

Ltd.

)

OEM MODEL

TPV MODEL

Size

Rev

acer H235H

715G3266-E

絬

隔

瓜

絪

腹

Key Component

Date

4.0.SCALER

PCB NAME

Sheet

称爹>

称爹

Tuesday , May 12, 2009

PA[0..9]

PB[0..9]

CN404

PA[0..9]

PB[0..9]

PB0 LVB3P

PB1 LVB3M

PB2 LVBCKP

PB3 LVBCKM

PB4 LVB2P

PB5 LVB2M

PB6 LVB1P

PB7 LVB1M

PB8 LVB0P

PB9 LVB0M

PA0

PA1

PA2

PA3

PA4

PA5

PA6

PA7

PA8

PA9

LVA3P

LVA3M

LVACKP

LVACKM

LVA2P

LVA2M

LVA1P

LVA1M

LVA0P

LVA0M

LVB0M

LVB0P

LVB1M

LVB1P

LVB2M

LVB2P

RXO0-

RXO0+

RXO1-

RXO1+

RXO2-

RXO2+

LVBCKM RXOC-

LVBCKP

LVB3M

LVB3P

LVA0M

LVA0P

RXOC+

RXO3-

RXO3+

RXE0-

RXE0+

LVA1M

LVA1P

RXE1-

RXE1+

VLCD

LVA2M

LVA2P

LVACKM RXEC-

LVACKP

LVA3M

LVA3P

RXE2-

RXE2+

VLCD

RXEC+

RXE3-

RXE3+

FB410

120 OHM

Panel_VCC

CN406

LVDS Wafer CONNECT

R552

220 OHM 1/4W

R494

220 OHM 1/4W C464

0.1uF 16V

CONN

C463

22uF/50V

RXO0-

RXO1-

RXO2-

RXOC-

RXO3-

RXE0-

RXE1-

RXE2-

RXEC-

RXE3-

RXO0+

RXO1+

RXO2+

RXOC+

RXO3+

RXE0+

RXE1+

RXE2+

RXEC+

RXE3+

NC CONN

Panel_VCC

T P V ( Top Victory Electronics Co . , Ltd. )

OEM MODEL

Size

Rev

acer H235H

715G3266-E

G3266-1B-X-X-3-090512

TPV MODEL

絬隔瓜絪腹

Key Component

5.0.PANEL INTERFACE

Tuesday, May 12, 2009

PCB NAME

Sheet

称爹>

称爹

Date

U501~U502 close to CN501

CN501

HDMI

U501

RClamp0524P.TCT

SHELL1

HDMI1_D2+

HDMI1_D1+

HDMI1_D1-

D2+

IN1

IN2

OUT1

OUT2

D2 Shield

D2-

HDMI1_D2-

HDMI1_D1+

SHELL3

HDMI1_D0+

HDMI1_D0-

D1+

IN3

IN4

OUT3

OUT4

D1 Shield

D1-

HDMI1_D1-

HDMI1_D0+

+5V

D0+

HDMI1_+5V

HDMI_+5V

D501

+5V 3,4,5

D0 Shield

D0-

HDMI1_D0-

HDMI1_CK+

BAT54C

CK+

U502

CK Shield

CK-

CE Remote

DDC CLK

DDC DATA

HDMI1_CK-

CEC

RClamp0524P.TCT

HDMI1_CK-

HDMI1_CK+

IN1

IN2

OUT1

OUT2

+5V

VCC3.3

DDC_CLK

DDC_DATA

VCC3.3 3,5

HDMI1_D2+

HDMI1_D2-

IN3

IN4

OUT3

OUT4

SHELL4

GND

+5V

HDMI_+5V

+5V

HP DET

R518

SHELL2

U503

R558

C502

0.22uF

CEC_CTRL

VCC A0

SCL A2

SDA VSS

Q502

R504

R505

100R 1/16W 5% HDMI1_SCL

100R 1/16W 5% HDMI1_SDA

R501

1K 1/16W 5%

R551

HDMI_HOTPLUG

10K 1/16W 5%

M24C02-WMN6TP

Q501

2N3904S-RTK/PS

C501

0.1uF 16V

CEC

HDMI_HOTPLUG

R506

22K 1/16W 5%

DDC_WP

HDMI_HPD

Q503

U505

2N3904S-RTK/PS

AZC199-04S

+5V

R507

D507

D506

HDMI_5V

C503

DET_INPUT

DDC_CLK

DDC_DATA

C504

LL4148

DVI5V

+5V

C512

R560

1K 1/16W 5%

R562

2K OHM 1/16W

0.47uF/16V

R573 0R05 1/16W

0.1uF 16V

DVI5V

100uF/16V

150K OHM 1/16W 5%

HDMI_+5V

R559

Q504

2N3904S-RTK/PS

R561

22K 1/16W 5%

Q505

2N3904S-RTK/PS

R507~R514 close to U504

U504

PI3HDMI1212BE

HDMI_CP-1

VDD33

D0+

D0-

D1+

D1-

VDD33

SEL

D2+

D2-

D3+

D3-

VDD33

GND

VDD33

GND

VDD50

GND

VDD50

VDD33

RXC-

D0+A

HDMI_CP-1

HDMI_CP-6

RXC+

RX2+

RX2-

RX1+

RX1-

RX0+

RX0-

D0-A

+5V

5V_EMI

D1+A

CLK-

CLK+

D1-A

D2+A

D2-A

R-

R+

D3+A

R563

10K 1/16W 5%

R465

10K 1/16W 5%

D3-A

HDMI_5V

R648

R575

0R05 1/16W

HDMI_CP-4

HDMI1_CK-

HDMI1_CK+

HDMI1_D2+

HDMI1_D2-

HDMI1_D1+

HDMI1_D1-

HDMI1_D0+

HDMI1_D0-

HDMI_SEL

VDD33

DET_HDMI R499

DET_VGA R463

DET_DVI R464

100R 1/16W 5%

DDC_WP

D0+B

G-

G+

D0-B

150K OHM 1/16W 5%

2N3904S-RTK/PS

100R 1/16W 5%

Q401

2N3904S-RTK/PS

D1+B

HDMI_CP-2

R564

Q506

D1-B

B-

B+

D2+B

D2-B

D3+B

R651

0R05 1/16W

D3-B

C505 0.1uF 16V

DET_DVI

DET_VGA

VDD33

GND

R647

0R05 1/16W

HDMI_CP-3

HDMI_5V

HDMI_CP-5

HDMI_SEL OUTPUT

VDD33

R649 4K7 1/16W 5%

DDCD_SCL

DDCD_SDA

GND

HDMI_CP-6

HDMI_CP-5

HDMI_CP-4

HDMI_CP-3

HDMI_CP-2

DVI_SCL

DVI_SDA

0B1

HDMI

DVI

HDMI1_SCL

HDMI1_SDA

0B2

1B1

1B2

GND

LOW

2B1

2B2

R527

R650 4K7 1/16W 5%

HDMI_5V

10K 1/16W 5%

3B1

3B2

HDMI_5V

HDMI_CP-1

VDD50

HDMI_SEL

GND

C506

0.1uF 16V

C507

0.1uF 16V

C508

0.1uF 16V

C509

0.1uF 16V

C510

0.1uF 16V

C511

0.1uF 16V

HDMI input channel 0=B,1=G,2=R

Custom

T P V ( Top Victory Electronics Co .

Ltd.

)

OEM MODEL

TPV MODEL

Size

Rev

acer H235H

715G3266-E

G3266-1B-X-X-3-090512

絬

隔

瓜

絪

腹

Key Component

Date

6.0.HDMI INPUT

PCB NAME

Sheet

称爹>

称爹

Tuesday, May 12, 2009

+5V_AUDIO

CN602

OUT-L+

OUT-L-

OUT-R+

OUT-R-

PCM1754DBQR

U601

C602

C603

0.1uF 16V

10uF/16V

R602

12KOHM1/16W

R606

R644

1K 1/16W 5%

R643

C637

C638

CONN

NC 220uF/25V

AUSCK

AUSDO

AUOUTLR R604

R605

R601

R603

75R 1/16W 5%

56 OHM 1/16W

I2S_SCK

I2S_SD0

I2S_LR

C632

C633

0.47uF/16V

HINL

AUSCK

AUSDO

AUOUTLR

BCK

VOUTL

DATA

12KOHM1/16W

1K 1/16W 5%

HINR

EOUTL

EOUTR

LRCK

VOUTR

I2S_MCK

TEST

ZEROA

SCK

R631

R630

FB611

C605 C606 C607 C608

22pF 22pF 22pF 22pF

NC 1K 1/16W 5%

120 OHM

FMT

VCOM

MUTE

DEMP

C612

C611

AUMCKO

R634

10K 1/16W 5%

10uF/16V

R609

10K 1/16W 5%

0.1uF 16V

R607

10K 1/16W 5%

AUMUTE

+5V_USB

CN605

R610

R611

2.7KOHM1/16W R645

2.7KOHM1/16W R646

1K 1/16W 5%

INL

INR

R637

CN603

NC/CONN

+5V_AUDIO

PHONEJACK

FB601

BEAD

+5V_AUDIO

+5V_USB

R617

R632 R633 change to #0603

CN601

R633

R616

EOUTL

IC with Heat-sink(90G6119-1)

R632

EOUTR

+5V_AUDIO

R636

C656

470uF 16V

+5V_USB

C623

470uF 16V

C622

+5V_AUDIO

D508

D509

0.1uF 16V

+5V_AUDIO

NC/PHONEJACK

R635

10K 1/16W 5%

U603

TPA6019A4PWPR

OUT-R+

C644

PGND

ROUT-

PVDD

RHPIN

RLINEIN

RIN

VDD

LIN

LLINEIN

LHPIN

PVDD

LOUT-

ROUT+

SE/BTL

HP/LINE

VOLUME

SEDIFF

SEMAX

AGND

BYPASS

FADE

SHUTDOWN

LOUT+

OUT-R-

SW_AUOUT

VOL

HINR

INR

C617

C618

0.47uF/16V

U604 NC SN74LVC1G34DBVR

C635 0.47uF/16V

C636 0.47uF/16V

N.C.VCC

R639 NC

SPDIF_OUT

CN606

JACK

C643

GND

INL

C613

C614

0.47uF/16V

R641 NC

C642

C640 NC

MUTE

HINL

OUT-L+

OUT-L-

R640

C641

PGND

C655

C630

0.47uF/16V

VOL

C654

ZD435

FB607

FB608

FB609

FB610

120 OHM

Custom

T P V ( Top Victory Electronics Co .

Ltd.

)

OEM MODEL

Size

acer H235H

G3266-1B-X-X-3-090512

TPV MODEL

絬

隔

瓜

絪

腹

Rev

Key Component

Date

7.0.AUDIO

PCB NAME

Sheet

715G3266-E

<称爹>

称爹

Tuesday , May 12, 2009

Power board

BD901A

KBP208G

L904

100 OHM 1/4W R918

100 OHM 1/4W R919

100 OHM 1/4W R920

+16V

Coil

C912

0.001uF

BD901

GBU408

R946

R947

ZD902

TZX18B

C917

C918

470UF M 35V

D906

FMX-12SL

820OHM 2W

FB902 0R05 1/4W

470UF M 35V

T901

R943

470R 1/8W 5%

POWER X'FMR

C905

R904

Q903

2SD1207T

1500PF2KV

8.2K OHM 1/4W

R935 100 OHM 1/4W

R961 100 OHM 1/4W

R939

1K 1/8W 5%

120uF450V

R903

C932

NC^C938

C906

1500PF2KV

100K OMH 2W +-5%

L903

0.001uF

R905

8.2K OHM 1/4W

C929

R962 100 OHM 1/4W 0.001uF

C904

F903

Coil

+5V

D901

NC(0.22UF275V)

FR103

FUSE

R924

C915

470UF M 16V

100R 1/8W 5%

C939

1000uF/25V

0.1uF C907

R909

3.3 OHM 1/4W

C908

22uF 50V

D900

FR107

R940

D907

31DQ06FC3

L901

27mH

Q901

STP10NK70ZFP

IN4148

IC903

PC123X2YFZOF

R927

IC901

D903

R910

C937

100pF/1KV

FB901

BEAD

10K 1/10W 1%

R925

1K 1/8W 5%

COMPNC

CS VCC

GNDOUT

R949 100 OHM

R950 100 OHM

C935

1000PF K 500V X7R

10R 1/4W 5%

LD7576

C940

C903

R938

10K 1/8W 5%

0.047uF

C924

0.1uF

R951 100 OHM

0.47UF275V

R901

R912

220 OHM 1/4W

C921

R902

R926

1K 1/10W 1%

R914

1M 1/4W 5%

IC904

KIA431A-AT/P

1000PF/250VAC

C909

220pF

0.39 OHM 2W +-5%

NR901

NTCR

D908

SP1060

R930

C900

C928

3300pF 250V

9K1 1/10W 1%

0.01uF

F901

FUSE

L906

JUMPER

! ! !

CN903

C902

C901

L905

1000pF

+16V

F902

CN902

CHOKE

+5V1

CONN

FUSE 4A 250V

C930

0.1uF 50V X7R

C916

1000UF M 25V

+5V

DIM

ON/OFF

C934

CN901

SOCKET

PID

C931

0.1uF

GND2

GND

GND1

GND

HS3

HEAT SINK(D906)

HS2

HS1

HEAT SINK(Q901)

VOL

CONN

MUTE

Custom

T P V ( Top Victory Electronics Co .

Ltd. )

OEM MODEL

TPV MODEL

Size

XXXX

+5V1

G2824-4-5-X-39-090513

絬

隔

瓜

絪

腹

PWPC9D41EQKP

715G2824-4-5

Rev

Key Component

Date

03.POWER

PCB NAME

Sheet

ODM MODEL

称爹

Wednesday , May 13, 2009

4R7 1/8W 5%

R817

+16V

Q805

ZD802

ON/OFF

RLZ5.6B

ZD803

RLZ5.6B

G1 D1

S1 D1

G2 D2

S2 D2

R816

4R7 1/8W 5%

+5V

CN801

CONN

R803

5K1 1/8W 5%

R804

5K1 1/8W 5%

PT801

POWER X'FMR 7

APM4548

C819

56pF3KV

DIM

PID

C815

0.1uF

R846 0R05 1/8W

R819

LV1

Q806

C802

4R7 1/8W 5%

0.047uF

C820

56pF3KV

G1 D1

S1 D1

G2 D2

S2 D2

R802

22R 1/8W 5%

LV2

L801

R805

C801

0.047uF

R818

C811

0.1uF

R847

4R7 1/8W 5%

APM4548

CONN

CN802

0R05 1/8W

C804

R828

6.2M1W

L802

R801

LV4

10K 1/10W 5%

1000uF 25V

R811

R807

C817

10K 1/10W 5%

82K1/10W

D801

2PF6KV

CN803

CONN

NDR1

PDR1

VDDA

TIMER

PWM

ISEN

OVPT SSTCMP

NDR2

GNDP

PDR2

GNDA

RT1

R810

R812

100K 1/10W 1%

C821

56pF3KV

IN4148

100K 1/10W 1%

C813

C814

220pF

R848

0R05 1/8W

LV3

ENA VSEN

R806

C809

220pF

R830

D806

D807

D808

R815 R808

NC 390R 1/10W 1%

IC801 ta9687GN-A-0-TR

Q802

BAV70

R836

56KOHM +-5% 1/10W

C822

56pF3KV

100K 1/10W 1%

6K8 1/8W 5%

C818

2N7002 SOT-23

R813

100K 1/10W 5%

R837

6K8 1/10W 5%

1.5UF/10V

C812 C806

NC 2.2uF/16V

C805

0.022uF

R809

C808

33NF50V

CONN

CN804

1M 1/10W 5%

C810

0.0033uF

BAV70

R838 1M 1/10W 5%

LV1

R839 1M 1/10W 5%

LV2

BAV70

R840 1M 1/10W 5%

LV3

D803

BAV99

R841 1M 1/10W 5%

LV4

R844

5.1K 1/10W 5%

R843

5.1K 1/10W 5%

R842

5.1K 1/10W 5%

R845

5.1K 1/10W 5%

Custom

T P V ( Top Victory Electronics Co . , Ltd. )

OEM MODEL XXXX

Size

Rev

G2824-4-5-X-39-090513

TPV MODEL

絬隔瓜絪

腹

PWPC9D41EQKP

715G2824-4-5

Key Component

Date

02.INVERTER

PCB NAME

Sheet

ODM MODEL

称爹

Wednesday , May 13, 2009

Hotpoint HW150GW User Manual
Hanns G HN198DP User Manual
EVGA 113 M2 E113 User Manual
Electrolux Air O Convect AOS102ECA1 User Manual
Eizo FlexScan EcoView User Manual
Cannon 50cm Free Standing Electric Cooker C50ELW User Manual
Black Decker TRO4085 User Manual
Beko 32WLA530HID User Manual
Asus P8H61 M LX R2 0 SERIES User Manual
AOC Computer Monitor E2343F2K User Manual