Uniden TCX930 User Manual

Compatible Bases  
Thꢀs handset ꢀs compatꢀble wꢀth Unꢀden's 5.8 GHz Dꢀgꢀtal  
Expandable phone system: the TRU9300 serꢀes.  
date lꢀst of compatꢀble bases.  
Installing the Accessory Handset  
Checking the Package Contents  
Make sure your package contaꢀns the followꢀng ꢀtems. If any  
ꢀtems are mꢀssꢀng or damaged, contact our Customer Servꢀce  
Hotlꢀne. See back cover page for contact ꢀnformatꢀon.  
• Cordless Handset  
• Beltclꢀp  
• Chargꢀng Cradle  
• Prꢀnted Materꢀal  
• AC Adapter, model # AD-0005  
Input: ꢁꢂ0V AC 60 Hz  
Output: 9V DC ꢂꢁ0 mA  
• Rechargeable NꢀMH Battery Pack, model # BT-909  
Capacꢀty: 600 mAh, 3.6V  
Installing the Battery  
Follow the steps below to ꢀnstall the  
rechargeable battery pack.  
ꢁ) Using the finger indentation, press in on  
the battery case cover and slꢀde ꢀt down  
to remove ꢀt.  
ꢂ) Plug the battery connector ꢀnto the  
battery compartment jack. Be sure to  
match the red and black wꢀres to the  
label near the jack.  
3) Gently pull on the battery wꢀres. If the  
battery connector comes loose, try  
connectꢀng ꢀt agaꢀn.  
4) Replace the battery case cover and slꢀde  
ꢀt up untꢀl ꢀt clꢀcks ꢀnto place.  
Note: Use only the Uniden BT-909 rechargeable battery pack  
supplied with your cordless telephone.  
Installing the Belt Clip  
Lꢀne up the tabs wꢀth the holes on each sꢀde of  
the handset. Press the belt clꢀp down untꢀl both  
tabs clꢀck ꢀnto place.  
To remove the belt clꢀp, pull both sꢀdes of the clꢀp  
to release the tabs from the holes.  
Installing the Optional Headset  
Your phone may be used wꢀth an optꢀonal headset.  
To use a headset, ꢀnsert the headset plug ꢀnto the  
headset jack. Headsets may be purchased by  
callꢀng the Unꢀden Parts Department. See back  
cover page for contact ꢀnformatꢀon.  
Charging the Accessory Handset  
The handset ꢀs powered by a rechargeable battery pack that  
automatꢀcally recharges when the handset ꢀs placed ꢀn the  
charger.  
ꢁ) Connect the AC adapter to the DC IN 9V jack and to a ꢁꢂ0V  
AC outlet that ꢀs not controlled by a wall swꢀtch.  
Caution: Use only the Uniden AD-0005 adapter.  
ꢂ) Set the charger on a  
desk or tabletop, and  
Route the  
cord.  
place the handset ꢀn the  
charger wꢀth the keypad  
facꢀng forward.  
3) Make sure that the  
charge LED ꢀllumꢀnates.  
If the LED does not  
ꢀllumꢀnate, check to see  
that the AC adapter  
ꢀs plugged ꢀn and  
To AC outlet  
To DC IN 9V  
the handset makes  
good contact wꢀth the  
chargꢀng contacts on  
the chargꢀng cradle.  
AC adapter (supplied)  
4) Charge the handset battery pack for at least ꢁ5-ꢂ0 hours  
before using your new handset for the first time.  
3
Registering the Handset  
You must regꢀster the handset to the base before you can use ꢀt.  
Only one handset can be regꢀstered at a tꢀme. (If an accessory  
handset has ever been regꢀstered to a base, you must reset the  
handset before you can regꢀster ꢀt to a new base.)  
To regꢀster to a TRU9300 serꢀes  
base, place the accessory  
Charge the handset  
for 15-20 hours.  
E
x
t
r
a
Handset  
handset ꢀn the base. Whꢀle the  
handset ꢀs regꢀsterꢀng, HANDSET  
REGISTERING appears ꢀn the  
LCD. When REGISTRATION  
COMPLETE ꢀs dꢀsplayed, the  
handset has been regꢀstered to  
the base.  
If REGISTRATION FAILED  
appears, remove the handset from  
the base and try agaꢀn.  
C
harger  
E
x
t
r
a
Handset  
Place the extra  
handset in the main  
base to register.  
M
a
i
n
Base  
E
x
t
r
a
Handset  
+
M
a
i
n
Base  
C
harger  
Resetting the Handset  
If you want to regꢀster the handset to a dꢀfferent base or replace  
a handset with another one, you must first clear the registration  
ꢀnformatꢀon from the base and the handset.  
ꢁ) Press and hold [ ] and [#] for at least 5 seconds, untꢀl the  
SYSTEM RESET menu appears.  
ꢂ) Select the DEREGISTER HS  
Which Handset?  
submenu by pressꢀng [select/ ].  
Handset  
Handset  
#1  
#2  
WHICH HANDSET? appears ꢀn the  
dꢀsplay.  
3) Use [ ] or [ ] to select the handset ID to be de-regꢀstered  
from the lꢀst, and then press [select/ ]. DEREGISTER HS  
appears.  
4) Press [ ] to move the cursor to YES, and then press  
[select/ ]. You will hear a confirmation tone.  
4
Resetting the Handset Without the Base  
If the orꢀgꢀnal base thꢀs handset was regꢀstered to ꢀs not  
avaꢀlable for some reason (for example, ꢀt ꢀs lost or somehow  
ꢀncapacꢀtated), you can stꢀll reset the handset and use ꢀt wꢀth  
another base.  
ꢁ) Press and hold [ ] and [#] for more than 5 seconds, untꢀl the  
SYSTEM RESET menu appears.  
ꢂ) Press [ ] to move the cursor to BASE UNAVAILABLE and  
then press [select/ ]. BASE UNAVAILABLE appears.  
3) Press [ ] to move the cursor to YES, and then press  
[select/ ]. You hear a confirmation tone, and the handset  
deletes ꢀts own lꢀnk to the base wꢀthout tryꢀng to contact the  
base.  
Now you are ready to regꢀster the handset to the new base.  
5
Using the Interface  
Parts of the Handset  
5
6
1
2
3
7
14  
15  
16  
17  
18  
8
9
10  
11  
4
12  
13  
19  
20  
21  
22  
ꢁ. Headset Jack Cover  
ꢂ. Beltclꢀp Hole  
ꢁꢂ. [ /tone] key  
ꢁ3. [hold/int’com/xfer] key  
*
3. Speakerphone Speaker  
and Rꢀnger  
4. Handset Battery  
Compartment  
5. New Message LED  
6. Handset Earpꢀece  
7. LCD Dꢀsplay  
ꢁ4. [redial/pause] key  
ꢁ5. [select/ ] key (select/  
messages)  
ꢁ6. [ ] key (caller ID/rꢀght)  
ꢁ7. [ ] key (end call)  
ꢁ8. [ ] key (down)  
ꢁ9. [#] key  
ꢂ0. [ ] key (speaker)  
ꢂꢁ. Handset Mꢀcrophone  
8. [menu/clear] key  
9.  
[
] key (up)  
ꢁ0. [ /flash] key (talk/flash)  
ꢁꢁ. [ ] key (phonebook/left)  
ꢂꢂ. Handset Chargꢀng  
Contacts  
6
Reading the Display  
The handset dꢀsplay uses ꢀcons to tell you the status of your  
phone. The table below lꢀsts the ꢀcons and what they mean.  
Icon  
Status  
Description  
Standby/ The battery ꢀcon ꢀndꢀcates the handset  
Talk  
battery status: full, medꢀum, low, and empty.  
The ringer off ꢀcon ꢀndꢀcates that the rꢀnger  
ꢀs turned off.  
Standby  
:OFF  
The mute ꢀcon appears whꢀle the handset  
Talk  
Talk  
Talk  
Talk  
mꢀcrophone ꢀs muted.  
The boost ꢀcon appears when the Clarꢀty  
Boost feature ꢀs actꢀvated.  
The speaker ꢀcon appears when the handset  
speaker phone ꢀs ꢀn use.  
The privacy ꢀcon appears when the Prꢀvacy  
Mode ꢀs turned on.  
The Standby Screen  
When the phone ꢀs ꢀn standby, the handset dꢀsplay shows the  
followꢀng ꢀtems:  
:OFF  
Ringer off icon (when the ringer is off) / battery icon  
Handset ID  
Handset #1  
New CID: 5  
Number of new Caller ID calls received  
Using the Four-way Function Key  
Your handset has a four-way  
functꢀon key that allows you to  
move the cursor or poꢀnter on  
the dꢀsplay and access the most  
Up  
commonly used features at the  
View the  
phonebook  
View the  
Caller ID  
touch of a button. Press the  
left sꢀde of the key to open the  
Four-way  
phonebook. Press the rꢀght sꢀde  
Function Key  
to open the Caller ID lꢀst.  
Down  
To use thꢀs four-way key, place your thumb over the key on the  
handset and move to the four posꢀtꢀons to get the feel of how ꢀt  
moves and operates.  
7
Using the Handset Menus  
To open the menu, press [menu/clear]. Select the optꢀon you  
want by pressꢀng the four-way functꢀon key. Thꢀs wꢀll move the  
cursor; the optꢀon currently selected has a trꢀangle besꢀde ꢀt.  
Actꢀvate the selected optꢀon by pressꢀng [select/ ]. To exꢀt the  
menu and return to standby, press [ ].  
If you do not press a key wꢀthꢀn 30 seconds, the phone wꢀll tꢀme  
out and exꢀt the menu.  
Entering Text from Your Handset  
You can use the number keypad on your phone to enter text by  
referrꢀng to the letters prꢀnted on each number key. When you  
press the number key in a text entry field, the phone displays  
the first letter printed on the number key. Press the number key  
twꢀce to dꢀsplay the second letter and three tꢀmes to dꢀsplay the  
third. Capital letters are displayed first, then lower case letters,  
then the number on the key.  
If two letters in a row use the same number key, enter the first  
letter, then use [right] or [left] on the four-way functꢀon key to  
move the cursor to the next posꢀtꢀon to enter the second letter.  
Number of times key is pressed  
8
For example, to enter "Movꢀes":  
ꢁ) Press [6] once to enter M.  
ꢂ) Use [right] on the four-way functꢀon key to move the cursor  
to the rꢀght.  
3) Press [6] sꢀx tꢀmes to enter o.  
4) Press [8] sꢀx tꢀmes to enter v.  
5) Press [4] sꢀx tꢀmes to enter i.  
6) Press [3] five times to enter e.  
7) Press [7] eꢀght tꢀmes to enter s.  
8) Press [select/ ] to end your text entry.  
If you make a mꢀstake whꢀle enterꢀng a name, use [right] or [left]  
on the four-way functꢀon key to move the cursor to the ꢀncorrect  
character. Press [menu/clear] to erase the wrong character, and  
then enter the correct character. To delete all characters, press  
and hold [menu/clear].  
9
Using Your Accessory Handset  
Making and Receiving Calls  
With the earpiece  
With the speaker phone  
ꢁ) Remove the handset from ꢁ) Remove the handset from  
the charger.  
ꢂ) Dꢀal the number.  
3) Press [ /flash].  
the charger.  
ꢂ) Dꢀal the number.  
Make a  
call  
3) Press [  
].  
ꢁ) Pꢀck up the handset.  
(If AutoTalk ꢀs on, the  
ꢁ) Pꢀck up the handset.  
(If AutoTalk ꢀs on, the  
phone answers when you  
remove the handset from  
the chargꢀng cradle.)  
phone answers when you  
remove the handset from  
the chargꢀng cradle.)  
Answer  
a call  
ꢂ) Press [ /flash].  
ꢂ) Press [  
].  
(If Any Key Answer ꢀs on,  
you can press any key ꢀn  
the twelve-key pad.)  
Hang up Press [ ].  
Press [ ].  
Adjusting the Volume  
Choose from four rꢀnger volume settꢀngs (off, low, medꢀum,  
Ringer  
Volume  
and hꢀgh). Wꢀth the phone ꢀn standby, use [  
] and [  
]
to adjust the rꢀnger volume.  
Choose from sꢀx volume levels for the earpꢀece. Whꢀle on  
a call, press [ ] to make the earpꢀece volume louder or  
] to make ꢀt softer.  
Earpiece  
Volume  
[
Choose from sꢀx volume levels for the handset  
Speaker  
Volume  
speakerphone. Whꢀle on a call, press [  
] to make the  
speaker volume louder or [  
] to make ꢀt softer.  
ꢁ0  
Using Caller ID and Call Waiting  
If you subscrꢀbe to Caller ID, you can store up to 30 Caller ID  
numbers ꢀn each handset. Caller ID records are stored from  
newest to oldest. Once your Caller ID lꢀst ꢀs full and you receꢀve  
an ꢀncomꢀng call, the oldest record wꢀll be automatꢀcally deleted  
to make room for the new record.  
To open the Caller ID lꢀst, press [ ]. The phone wꢀll show the  
number of new Caller ID records and the total number of stored  
records. From the screen, you have the followꢀng optꢀons:  
Scroll through the  
records  
Press [  
] to scroll through CID records.  
CID records are stored chronologꢀcally from  
newest to oldest.  
Jump to records that  
Press the number key correspondꢀng to the  
start wꢀth a certaꢀn letter letter you want to jump to.  
Store a record ꢀn the  
phonebook  
Fꢀnd the record you want to store and press  
[select/ ].  
Dꢀal a record  
Fꢀnd the entry you want to dꢀal and press  
[ /flash] or [  
].  
Delete a record  
Fꢀnd the entry you want to dꢀal and press  
[menu/clear].  
Delete all records  
Press [menu/clear].  
Exꢀt the Caller ID lꢀst  
Press [ ].  
Using Call Waiting  
If you subscrꢀbe to call waꢀtꢀng, a tone sounds ꢀf a call comes ꢀn  
when you are on the phone. If you subscrꢀbe to Caller ID on call  
waꢀtꢀng, the Caller ID ꢀnformatꢀon of the waꢀtꢀng call appears on  
the dꢀsplay. Press [ /flash] on the handset to accept the waꢀtꢀng  
call. After a short pause, you wꢀll hear the new caller. To return to  
the orꢀgꢀnal caller, press [ /flash] on the handset agaꢀn.  
ꢁꢁ  
Using the Phonebook  
Your handset can store up to 70 names and numbers ꢀn your  
phonebook. When all the phonebook entrꢀes are full, you wꢀll  
hear a beep and MEMORY FULL appears. You cannot store any  
addꢀtꢀonal names and numbers unless you delete some of the  
exꢀstꢀng ones.  
Press [ ] to enter the phonebook menu. Once ꢀn the  
phonebook menu, you have the followꢀng optꢀons:  
ꢁ) Press [  
] agaꢀn or move the cursor to  
DIAL/EDIT and press [select/ ].  
Scroll through the  
entrꢀes  
ꢂ) Press [  
] to scroll through the phonebook  
alphabetꢀcally.  
Jump to entrꢀes  
that start wꢀth a  
certaꢀn letter  
Press the number key correspondꢀng to the letter  
you want to jump to.  
Move the cursor to CREATE NEW, then press  
[select/ ].  
Store a new entry  
ꢁ) Move the cursor to COPY and press [select/ ].  
ꢂ) Select the handset you want to copy the entrꢀes  
to and press [select/ ].  
Copy entrꢀes to  
another handset  
3) Select ONE MEMORY or ALL MEMORY and  
press [select/ ].  
4) If you choose ONE MEMORY, nd the entry you  
want to copy and press [select/ ].  
ꢁ) Move the cursor to DIAL/EDIT and press  
[select/ ].  
ꢂ) Fꢀnd the entry you want to dꢀal.  
Dꢀal an entry  
3) Press [ /flash] or [  
].  
ꢁ) Move the cursor to DIAL/EDIT and press  
[select/ ].  
ꢂ) Fꢀnd the entry you want to delete.  
3) Press [menu/clear].  
Delete an entry  
Delete all entrꢀes  
Move the cursor to DELETE ALL and press  
[select/ ].  
Close the  
phonebook  
Press [ ] or press [  
] agaꢀn ꢀf you are on a call.  
ꢁꢂ  
Redialing a Number  
To redial one of the last five numbers dialed on this handset,  
press [redial/pause] when the phone ꢀs ꢀn standby. Thꢀs opens  
the redꢀal lꢀst. Use [ ] and [ ] to find the number you want to  
dꢀal, and press [ /flash] or [ ].(You can also press [ /flash] or  
[
], and then [redial/pause] to redꢀal the last number dꢀaled.)  
Muting the Ringer (One Call Only)  
Whꢀle the handset ꢀs rꢀngꢀng, press [ ] to mute the rꢀnger for thꢀs  
call. The phone wꢀll rꢀng agaꢀn on the next call. (The handset  
must be off the cradle to mute the rꢀnger.)  
Muting the Microphone  
To mute the mꢀcrophone so the caller can't hear you, press  
[menu/clear]. Move the cursor to select MUTE and then press  
[select/ ]. MUTE ON and appear ꢀn the dꢀsplay. Repeat the  
procedure to cancel mutꢀng.  
Privacy Mode  
To prevent other statꢀons from ꢀnterruptꢀng a call, press  
[menu/clear]. Move the cursor to select CALL PRIVACY and  
then press [select/ ]. PRIVACY MODE ON and P appear ꢀn  
the dꢀsplay. Repeat the procedure to turn off prꢀvacy mode.  
Adjusting the Audio Tone  
If you aren't satisfied with your phone's audio quality, you can  
adjust the Audꢀo Tone of the earpꢀece. Whꢀle on a call, press  
[select/ ] to cycle through the three audꢀo tone optꢀons:  
low, natural and hꢀgh. (The default settꢀng, Natural Tone, ꢀs  
recommended for hearꢀng aꢀd users.) When the desꢀred optꢀon  
appears on the dꢀsplay, stop. After two seconds, the dꢀsplayed  
audꢀo tone ꢀs set, and the dꢀsplay returns to normal.  
ꢁ3  
Using the Clarity Boost Feature  
If you encounter ꢀnterference whꢀle you are on a call, you can  
manually ꢀmprove the sound by turnꢀng on the clarꢀty boost  
feature. Press [menu/clear], move the cursor to select CLARITY  
BOOST, and then press [select/ ]. BOOST ON and B appear  
ꢀn the dꢀsplay.  
Use the same procedure to turn off clarꢀty boost feature, BOOST  
OFF appears.  
ꢁ4  
Using Hold, Conference, Transfer and Intercom  
Press [hold/int'com/xfer]. If you leave a caller  
on hold for more than five minutes, the call will be  
Put a call on hold  
dꢀsconnected. To return to the party on hold, press  
[ /flash] or [  
].  
To joꢀn a call already ꢀn progress, press [ /flash] or  
Join a call already  
in progress  
[
]. You can hang up normally; the other statꢀon  
remaꢀns connected to the call.  
Press [hold/int'com/xfer]; the call ꢀs placed on  
hold. Use [  
] or [  
] to select the statꢀon you  
want to transfer the call to, and press [select/  
]. (To page all statꢀons at once, select ALL.)  
When the other statꢀon answers, you can talk  
to the statꢀon; the outsꢀde call remaꢀns on hold.  
If the other statꢀon accepts the call, you wꢀll be  
dꢀsconnected.  
Transfer a call  
To cancel the transfer and return to the call,  
Cancel a transfer  
press [ /flash] or [  
].  
To answer the transfer page and speak to the  
transferrꢀng statꢀon, press [ /flash] or [hold/  
int'com/xfer]. To accept the call and speak to the  
caller, press [ /flash] agaꢀn.  
Accept a  
transferred call  
Wꢀth the phone ꢀn standby, press [hold/int'com/  
xfer].  
Use [  
Make an intercom  
page  
] or [  
] to select the statꢀon you want  
to talk wꢀth, then press [select/ ]. (If you select  
ALL, all other statꢀons wꢀll be paged.)  
Cancel a page  
To cancel the ꢀntercom page, press [ ].  
Press [ /flash] or [hold/int'com/xfer]. If AutoTalk  
ꢀs on, the handset automatꢀcally answers the page  
when you remove ꢀt from the cradle.  
Answer an  
intercom page  
ꢁ5  
Accessing Your Answering Machine  
If your base has an answerꢀng machꢀne, you can use your  
handset to get your messages and change your answerꢀng  
machꢀne setup. You have the followꢀng optꢀons:  
Play  
messages  
Press [select/ ]. The system announces the number  
of new and old messages and plays the message.  
Press [  
] to go to the start of the current message.  
] repeatedly to go back to a prevꢀous  
Repeat a  
message  
Press [  
message.  
Skip a  
message  
Press [  
] to go to the begꢀnnꢀng of the next message.  
Delete a  
message  
Whꢀle a message ꢀs playꢀng, press [ ].  
The message ꢀs permanently deleted.  
Exit and  
hang up  
Press [ ] to exꢀt the system and return to standby.  
Screening Calls  
If your base has an answerꢀng machꢀne, you can lꢀsten to callers  
as they leave a message. Press [select/ ] when the system ꢀs  
answerꢀng to lꢀsten to the caller wꢀthout answerꢀng the phone.  
ꢁ6  
Accessing Voicemail  
If your base doesn't have an answerꢀng machꢀne and you  
subscrꢀbe to a voꢀce maꢀl servꢀce, you can program your handset  
to automatꢀcally dꢀal the access number.  
ꢁ) Press [menu/clear].  
ꢂ) Move the cursor to HANDSET SETUP and press [select/ ].  
3) Move the cursor to EDIT VOICE MAIL and press [select/ ].  
4) Enter your access number (up to ꢂ0 dꢀgꢀts). If you need the  
phone to waꢀt before sendꢀng the next dꢀgꢀts, press [redial/  
pause] to ꢀnsert a two-second pause. For a longer pause,  
press [redial/pause] multꢀple tꢀmes. Each pause counts as  
one dꢀgꢀt.  
5) Press [select/ ] when you are finished.  
Once you program your access number, press [select/ ] to  
dꢀal your voꢀce maꢀl servꢀce.  
Maintenance  
Battery Life  
Wꢀth average use, your battery talk tꢀme wꢀll be approxꢀmately  
5 hours and standby tꢀme wꢀll be approxꢀmately 7 days. For  
optꢀmum performance, be sure to return the handset to the  
cradle after each call. If the handset ꢀs left off of the chargꢀng  
cradle, the actual talk tꢀme duratꢀon wꢀll be reduced respectꢀve to  
the amount of tꢀme the handset ꢀs off the cradle.  
Note: Do not place the power cord where it creates a trip hazard  
or where it could become chafed and create a fire or  
electrical hazard.  
Low Battery Alert  
When the battery pack ꢀs very low, the dꢀsplay shows LOW  
BATTERY and the empty battery ꢀcon. If the phone ꢀs ꢀn standby,  
none of the keys wꢀll operate. If you are on a call, complete your  
conversatꢀon as quꢀckly as possꢀble, and return the handset to  
the chargꢀng cradle.  
ꢁ7  
Battery Replacement and Handling  
Wꢀth normal usage, your battery should last about one year.  
If the talk tꢀme becomes short even after the battery ꢀs recharged,  
please replace the battery. You can purchase a replacement  
battery by callꢀng Unꢀden's Parts department. See the back cover  
page for contact ꢀnformatꢀon.  
Warning  
To avoid the risk of personal injury or property damage from fire or  
electrical shock, use only the BT-909 battery pack.  
Caution:  
- This equipment contains a rechargeable Nickel-Metal-Hydride  
battery.  
- Do not remove the batteries to charge them.  
- Never throw the battery in a fire or disassemble or heat it.  
- Do not remove or damage the battery casing.  
- Nickel is a chemical known to state of California to cause cancer.  
- Do not short-circuit the battery.  
- Do not charge the battery used in this equipment in any charger  
other than the one designed to charge this battery as specified in  
the owner's manual. Using another charger may damage the  
battery or cause the battery to explode.  
- Rechargeable batteries must be recycled or disposed of properly.  
Clean the Battery Contacts  
To maꢀntaꢀn a good charge, clean the  
chargꢀng contacts on the handset once a  
month. Dampen a cloth wꢀth plaꢀn water.  
Gently rub the damp cloth over the chargꢀng  
contacts untꢀl all vꢀsꢀble dꢀrt ꢀs removed.  
Dry the contacts thoroughly before returnꢀng  
the handset to the chargꢀng cradle.  
Caution:  
Do not use any chemical products (benzene, alcohol, paint thinner,  
etc.), or you may discolor the surface and damage the finish.  
ꢁ8  
The FCC Wants You To Know  
Changes or modifications to this product not expressly approved by  
Unꢀden, or operatꢀon of thꢀs product ꢀn any way other than as detaꢀled by  
the owner's manual, could voꢀd your authorꢀty to operate thꢀs product.  
Thꢀs devꢀce complꢀes wꢀth part ꢁ5 of the FCC rules. Operatꢀon ꢀs subject  
to the followꢀng two condꢀtꢀons: (ꢁ) Thꢀs devꢀce may not cause harmful  
ꢀnterference, and (ꢂ) Thꢀs devꢀce must accept any ꢀnterference receꢀved,  
ꢀncludꢀng ꢀnterference that may cause undesꢀred operatꢀon. Prꢀvacy of  
communꢀcatꢀons may not be ensured when usꢀng thꢀs phone.  
To nsure the safety of users, the FCC has establꢀshed crꢀterꢀa for  
the amount of radꢀo frequency energy varꢀous products may produce  
dependꢀng on theꢀr ꢀntended usage. Thꢀs product has been tested  
and found to comply wꢀth the FCC's exposure crꢀterꢀa. For body worn  
operatꢀon, the FCC RF exposure guꢀdelꢀnes were also met when used  
wꢀth the Unꢀden accessorꢀes supplꢀed or desꢀgned for thꢀs product. Use  
of other accessorꢀes may not ensure complꢀance wꢀth FCC RF exposure  
guꢀdelꢀnes and should be avoꢀded.  
I.C. Notice  
Terminal Equipment  
NOTICE:Thꢀs equꢀpment meets the applꢀcable Industry Canada Termꢀnal  
Equipment Technical Specifications. This is confirmed by the registration  
number. The abbreviation, IC, before the registration number signifies  
that regꢀstratꢀon was performed based on a Declaratꢀon of Conformꢀty  
indicating that Industry Canada technical specifications were met. It does  
not ꢀmply that Industry Canada approved the equꢀpment.  
NOTICE:The Rꢀnger Equꢀvalence Number (REN) for thꢀs termꢀnal  
equꢀpment ꢀs marked on the equꢀpment ꢀtself. The REN assꢀgned to  
each termꢀnal equꢀpment provꢀdes an ꢀndꢀcatꢀon of the maxꢀmum number  
of termꢀnals allowed to be connected to a telephone ꢀnterface. The  
termꢀnatꢀon on an ꢀnterface may consꢀst of any combꢀnatꢀon of devꢀces  
subject only to the requꢀrement that the sum of the Rꢀnger Equꢀvalence  
Numbers of all the devices does not exceed five.  
Radio Equipment  
The term "IC:" before the radio certification number only signifies  
that Industry Canada technical specifications were met. Operation is  
subject to the followꢀng two condꢀtꢀons: (ꢁ) thꢀs devꢀce may not cause  
ꢀnterference, and (ꢂ) thꢀs devꢀce must accept any ꢀnterference, ꢀncludꢀng  
ꢀnterference that may cause undesꢀred operatꢀon of the devꢀce. "Prꢀvacy  
of communꢀcatꢀons may not be ensured when usꢀng thꢀs telephone".  
ꢁ9  
One Year Limited Warranty  
Important: Evꢀdence of orꢀgꢀnal purchase ꢀs requꢀred for warranty  
servꢀce. WARRANTOR: UNIDEN AMERICA CORPORATION ("Unꢀden")  
ELEMENTS OF WARRANTY: Unꢀden warrants, for one year, to the  
orꢀgꢀnal retaꢀl owner, thꢀs Unꢀden Product to be free from defects ꢀn  
materꢀals and craftsmanshꢀp wꢀth only the lꢀmꢀtatꢀons or exclusꢀons set  
out below.  
WARRANTY DURATION: Thꢀs warranty to the orꢀgꢀnal user shall  
termꢀnate and be of no further effect ꢁꢂ months after the date of orꢀgꢀnal  
retaꢀl sale. The warranty ꢀs ꢀnvalꢀd ꢀf the Product ꢀs (A) damaged or not  
maintained as reasonable or necessary, (B) modified, altered, or used  
as part of any conversion kits, subassemblies, or any configurations  
not sold by Unꢀden, (C) ꢀmproperly ꢀnstalled, (D) servꢀced or repaꢀred by  
someone other than an authorꢀzed Unꢀden servꢀce center for a defect  
or malfunctꢀon covered by thꢀs warranty, (E) used ꢀn any conjunctꢀon  
wꢀth equꢀpment or parts or as part of any system not manufactured by  
Unꢀden, or (F) ꢀnstalled or programmed by anyone other than as detaꢀled  
by the owner's manual for thꢀs product.  
STATEMENT OF REMEDY: In the event that the product does not  
conform to thꢀs warranty at any tꢀme whꢀle thꢀs warranty ꢀs ꢀn effect,  
warrantor wꢀll eꢀther, at ꢀts optꢀon, repaꢀr or replace the defectꢀve unꢀt and  
return ꢀt to you wꢀthout charge for parts, servꢀce, or any other cost (except  
shꢀppꢀng and handlꢀng) ꢀncurred by warrantor or ꢀts representatꢀves  
ꢀn connectꢀon wꢀth the performance of thꢀs warranty. Warrantor, at  
ꢀts optꢀon, may replace the unꢀt wꢀth a new or refurbꢀshed unꢀt. THE  
LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE  
WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF  
AND EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE  
WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY  
OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY  
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR  
A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER  
OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF  
INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not  
allow thꢀs exclusꢀon or lꢀmꢀtatꢀon of ꢀncꢀdental or consequentꢀal damages  
so the above lꢀmꢀtatꢀon or exclusꢀon may not apply to you.  
ꢂ0  
LEGAL REMEDIES: This warranty gives you specific legal rights, and  
you may also have other rꢀghts whꢀch vary from state to state. Thꢀs  
warranty ꢀs voꢀd outsꢀde the Unꢀted States of Amerꢀca and Canada.  
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY:  
If, after followꢀng the ꢀnstructꢀons ꢀn the owner's manual you are certaꢀn  
that the Product ꢀs defectꢀve, pack the Product carefully (preferably ꢀn  
ꢀts orꢀgꢀnal packagꢀng). Dꢀsconnect the battery from the Product and  
separately secure the battery ꢀn ꢀts own separate packagꢀng wꢀthꢀn the  
shꢀppꢀng carton. The Product should ꢀnclude all parts and accessorꢀes  
orꢀgꢀnally packaged wꢀth the Product. Include evꢀdence of orꢀgꢀnal  
purchase and a note descrꢀbꢀng the defect that has caused you to return  
ꢀt. The Product should be shꢀpped freꢀght prepaꢀd, by traceable means,  
to warrantor at:  
Unꢀden Amerꢀca Servꢀce  
4700 Amon Carter Blvd.  
Fort Worth, TX 76ꢁ55  
ꢂꢁ  
At Uniden, we'll take care of you!  
Thank you for purchasꢀng a Unꢀden product. ꢀf you have any  
questꢀons or problems, please do not return thꢀs product to the  
place of purchase.  
Our customer care specꢀalꢀsts are here to  
Having  
trouble?  
com or call our Customer Servꢀce Hotlꢀne at  
ꢁ-800-ꢂ97-ꢁ0ꢂ3 durꢀng regular busꢀness hours.*  
To order headsets, addꢀtꢀonal handsets,  
replacement batterꢀes, or other accessorꢀes,  
ꢁ-800-554-3988 durꢀng regular busꢀness hours.*  
Need a part?  
Help for our If you need specꢀal assꢀstance due to a dꢀsabꢀlꢀty  
customers or have questꢀons on the accessꢀbꢀlꢀty features  
with special of thꢀs product, please call ꢁ-800-874-93ꢁ4  
needs (voꢀce or TTY).  
* Central Standard Tꢀme. Detaꢀled customer servꢀce hours are avaꢀlable  
May be covered under one or more of the followꢀng U.S. patents:  
4,797,9ꢁ6  
5,533,0ꢁ0  
5,66ꢁ,780  
5,73ꢂ,355  
5,787,356  
5,9ꢁꢂ,968  
5,987,330  
6,3ꢁ4,ꢂ78  
6,78ꢂ,098  
6,90ꢁ,ꢂ7ꢁ  
5,4ꢂ6,690  
5,574,7ꢂ7  
5,663,98ꢁ  
5,754,407  
5,794,ꢁ5ꢂ  
5,9ꢁ5,ꢂꢂ7  
6,044,ꢂ8ꢁ  
6,4ꢁ8,ꢂ09  
6,788,9ꢂ0  
6,907,094  
5,434,905  
5,58ꢁ,598  
5,67ꢁ,ꢂ48  
5,758,ꢂ89  
5,80ꢁ,466  
5,9ꢂ9,598  
6,070,08ꢂ  
6,6ꢁ8,0ꢁ5  
6,788,953  
6,9ꢁ4,940  
5,49ꢁ,745  
5,650,790  
5,696,47ꢁ  
5,768,345  
5,8ꢂ5,ꢁ6ꢁ  
5,930,7ꢂ0  
6,ꢁꢂ5,ꢂ77  
6,67ꢁ,3ꢁ5  
6,839,550  
6,953,ꢁꢁ8  
5,493,605  
5,660,ꢂ69  
5,7ꢁ7,3ꢁꢂ  
5,893,034  
5,864,6ꢁ9  
6,ꢂ53,088  
6,ꢂ53,088  
6,7ꢁ4,630  
6,889,ꢁ84  
7,0ꢂ3,ꢁ76  
Other patents pendꢀng.  
ꢂꢂ  

Timex Computer Drive DATAX4 User Manual
Technicolor Thomson TM9233 User Manual
Sony CDP 608ESD User Manual
Seagate Constellation ST2000NM0043 User Manual
Samsung SGH X105 User Manual
Research In Motion Blackberry Cell Phone MAT 14956 001 User Manual
Philips SRU9600 User Manual
Philips ACT 7583 User Manual (1)
Nokia CLASSIC 6220 User Manual
Nokia Cell Phone 5140I User Manual