DUAL BAND GPRS Series
SGH-x105
Portable Digital Telephone
User Manual
Please read this manual before operating your phone, and keep
it for future reference.
Printed in Korea
Code No.: GH68-04228A
English. 05/2003. Rev. 1.0
Samsung Telecommunications America (STA), Inc.
Headquarters:
1130 E. Arapaho Road
Richardson, TX 75081
Tel: 972-761-7000
Fax: 972-761-7001
Customer Care Center:
1601 E. Plano Parkway
Suite 150
Plano, TX 75047
Tel: 888-987-HELP (4357)
Fax: 972-761-7501
Internet Address: http://www.samsungusa.com/wireless
©2003 Samsung Telecommunications America. All rights
reserved. No reproduction in whole or in part allowed without
prior written approval. Samsung is a registered trademark of
Samsung Electronics America, Inc. and its related entities.
Table of Contents
Important Safety Precautions............................. 7
Your Phone ..................................................... 11
Display............................................................. 15
Selecting Functions and Options ................. 33
Phonebook ..................................................... 35
Searching for and Dialing a Number in the
Phonebook ......................................................... 38
Entering Text ................................................... 45
Using the Upper/Lower-Case Character
Mode................................................................... 47
In-Call Options ............................................... 51
Using the Menus............................................. 56
Picture Message ............................................ 71
Call Records ................................................... 80
Network Services ......................................... 106
Funbox .......................................................... 110
Solving Problems.......................................... 113
Access Codes.............................................. 116
WAP Browser................................................. 119
Health and Safety Information ................... 127
Usage guidelines:
All about performance and safety................ 127
Maintaining Safe Use of and Access to Your
Phone ................................................................ 129
Acknowledging Special Precautions and
FCC.................................................................... 133
STANDARD LIMITED WARRANTY................... 149
Glossary ........................................................ 155
Index ............................................................. 160
Important Safety Precautions
Read these guidelines before using your wireless phone. Failure
to comply with them may be dangerous or illegal. For more
detailed safety information, see “Health and Safety Information”
Road Safety at All Times
Do not use a hand-held phone while driving; park the vehicle
first.
Switching Off When Refueling
Do not use the phone at a service station or near fuels or
chemicals.
Switching Off in Aircraft
Wireless phones can cause interference. Using them in aircraft is
both illegal and dangerous.
Switching Off in Hospitals
Switch off your phone near medical equipment. Follow any
regulations or rules in force.
Interference
All wireless phones may be subject to interference, which could
affect their performance.
Special Regulations
Meet any special regulations in force in any area and always
switch off your phone whenever it is forbidden to use it, or when it
may cause interference or danger (in a hospital for example).
Important Safety Precautions
7
Radio Frequency Exposure
The design of this phone complies with FCC (of the U.S.
government) requirements relating to radio frequency (RF)
exposure. To maintain compliance with these requirements, use
only Samsung-supplied or approved accessories. Use of non-
approved accessories may violate the requirements.
Sensible Use
Use only in the normal position (held to the ear). Avoid
unnecessary contact with the antenna when the phone is
switched on.
Accessories and Batteries
Use only Samsung-approved accessories and batteries.
Qualified service
Only qualified service personnel may install or repair your phone.
Important Safety Precautions
8
Your Phone
Phone Layout
The following illustrations show the main elements of your phone.
Service Light
Earpiece
Ear-microphone
jack (on side)
Display
Volume/Menu
browse keys
(on side)
Navigation
keys
Softkey/Left
Softkey/Right
Dial /Menu
Confirmation
key
Power on/off/
Menu exit key
Alphanumeric
keys
Cancel/
correction key
Microphone
Special function keys
Your Phone
11
Key
Description
In the Menu Mode, scroll through the menu
options and phonebook memory.
In idle mode, allow you to access your
favorite menu options directly (for more
In the menu facility, return to the previous
menu level and select the current menu
respectively.
When entering text, move the cursor left
and right respectively.
In idle mode, allow you to access your
favorite menu options directly (for more
Perform the functions indicated by the text
above them (on the bottom line of the
display).
(soft keys)
In idle mode, launches the WAP Browser
directly.
Your Phone
12
Key
Description (Continued)
Deletes characters from the display.
In the menu facility, returns to the previous
menu level.
Makes or answers a call.
When held down in idle mode, recalls the
last numbers dialed or received.
In the menu facility, selects a menu
function or stores information that you have
entered (such as a name) in the phone or
SIM memory.
Ends a call. Also switches the phone on
and off when held down.
In the menu facility, returns to the idle
mode and cancels your input.
When held down in idle mode, accesses
your voice mail.
Enter numbers, letters and some special
characters. The key with the * is used to
change from upper to lower case when
entering text. The key with the # is used to
enter a space, or to turn on the silent/
vibration function.
Your Phone
13
Key
Description (Continued)
(on the side of the phone)
During a call, adjust the earpiece volume.
In idle mode, adjust the key volume.
In the menu facility, scroll through the
menu options and phone book memory.
Your Phone
14
Display
Display Layout
The display is comprised of three areas.
Area
Description
First line
Displays various icons (see
page 16).
Middle lines
Last line
Display messages, instructions and
any information that you enter
(number to be dialed, for example).
Shows the functions currently
assigned to the two soft keys.
Display
15
Icons
Icon
Description
Shows the received signal strength. The
greater the number of bars, the better the
signal strength.
Appears when a call is in progress.
Appears when you are connected to the GPRS
network.
Appears when the Silent mode is active or you
you receive a call; for further details, see
Appears when a new text message has been
received.
Appears when a new voice mail message has
been received.
Appears when you are entering text to indicate
the current text input mode.
Display
16
Icon
Description
Appears when you set the alarm.
Shows the level of your battery. The more bars
you see, the more power you have left.
Appears when the Mute mode is active.
Backlight
The display is illuminated by a backlight. When you press any
key, the backlight illuminates. It turns off if no key is pressed
within a given period of time, depending on the Back Light menu
option.
To specify the length of time for which the backlight is active, set
further details.
You can also set the phone to use the backlight only during a
specified period time, via the Auto Light menu option (Menu
Main Screen Display
Your phone has a main screen display. It indicates that you have
an incoming call or a message, and notifies you at the specified
time when you set an alarm.
Display
17
Getting Started
Installing the SIM Card
When you subscribe to a cellular network, you are provided with
a plug-in SIM card loaded with your subscription details, such as
your PIN, any optional services available and so on.
Note: The plug-in SIM card and its contacts can be easily damaged by
scratches or bending, so be careful when handling, inserting or removing
the card. Keep all SIM cards out of the reach of small children.
1. If necessary, switch off the phone by holding down the
key until the power-off image is displayed.
2. Remove the battery. To do so:
● Press down the catch above the battery and hold it in this
position.
● Slide the battery and lift it away, as shown.
Getting Started
19
3. Slide the SIM card into the SIM card holder so that the holder
locks the card in position. Make sure that the cut corner is top
right and the gold contacts of the card face into the phone.
Note: When you need to remove the SIM card, slide it, as shown, and
take it out of the holder.
4. Place the battery back, taking care to match the tabs on the
battery with the grooves on the phone.
Getting Started
20
5. Slide the battery towards the top of the phone until it clicks into
place. Make sure that the battery is properly installed before
switching on the power.
Charging a Battery
Your phone is powered by a rechargeable Li-ion battery. A travel
adapter is provided with your phone. Use only approved batteries
and chargers. Ask your local Samsung dealer for further details.
The phone can be used while the battery is charging, but this will
cause the phone to charge more slowly.
Note: You must fully charge the battery before using your phone for the
first time. A discharged battery is fully recharged in approximately
200 minutes.
6. With the battery in position on the phone, connect the lead
from the travel adapter to the bottom of the phone.
7. Connect the adapter to a standard AC wall outlet.
Getting Started
21
8. When charging is finished, disconnect the adapter from the
power outlet and from the phone by pressing the grey tabs on
both sides of the connector and pulling the connector out.
Low Battery Indicator
When the battery is weak and only a few minutes of talk time
remain, you will hear a warning tone and a message will be
repeated at regular intervals on the display:
When the battery becomes too weak for the phone to operate, it
switches off automatically.
Switching the Phone On/Off
1. Hold down the
key until the phone switches on.
Getting Started
22
2. If the phone asks for a password, key in the password and
press the OK soft key. The phone password is factory set to
00000000. For further details, see page 121.
3. If the phone asks for a PIN, key in the PIN and press the OK
searches for your network and when it finds it, the idle screen
appears with the Service Provider’s name, date and time.
Now, you can make or receive a call.
Note: The display language is factory set to English. To change the
language, use the Language menu option (Menu 5.4); for further details,
switching the phone off by pressing the Unlock soft key and the * key
4. When you wish to switch the phone off, hold down the
key until the power-off image is displayed.
Note: If you locked the keypad, you must unlock it before switching the
phone off by pressing the Unlock soft key and the * key.
Locking or Unlocking the keypad
You can lock the keypad to avoid pressing keys by mistake.
In Idle Mode, press and hold the * key until the LOCK icon and
“Keypad Locked” appear on the display.
You can answer incoming calls using any keys, even if you lock
the keypad. when you receive a call in the key lock mode, the
keypad is automaticlly unlocked. After the call, the key lock
mode is canceled.
You can dial emergency calls even if you lock the keypad. When
the confirming message appears, select Yes by pressing the left
soft key or the Green phone key. When you end the call, your
phone returns to the key lock mode after the period of time
specified in the Phone Lock menu option.
Getting Started
23
To exit the key lock mode, press the UnLock soft key and then
press the * key again. “Keypad Unlocked” appears and the Lock
icon no longer displays.
Getting Started
24
Call Functions
Making a Call
When the idle screen is displayed, key in the area code and
phone number, and press the
key.
Note: If you have checked the Auto Redial option in the Extra Settings
menu (Menu 5.6.1), the number is redialed automatically up to ten times
when the person does not answer the call or is already on the phone; see
page 96 for further details.
Making a International Call
1. Press and hold down the 0 key.
The + character appears.
2. Key in the country code, area code and phone number and
press the
key.
Call Functions
25
Correcting the Number
To clear...
Then...
The last digit
displayed
Press the
Press the
cursor is immediately to the right of
the digit to be cleared. Press the
key.
or
Any other digit
in the number
key until the
key. You can also insert a
missing digit simply by pressing the
appropriate key.
The whole
display
Hold down the
key for more
than one second.
Ending a Call
When you have finished your call, briefly press the
key.
Redialing the Last Number
The phone stores the numbers you dialed, received or missed.To
recall any of these numbers, proceed as follows.
1. If you have typed any characters on the display, clear the
display by holding down the
second.
key for more than one
2. Press the
key to display a list of the last numbers in the
order in which the calls were made.
Call Functions
26
3. Use the
and
keys to scroll through the numbers until
the required number is highlighted.
4.To...
Then...
Dial the number
highlighted
Press the
key.
Edit the number
highlighted
Press the Options soft key
select Edit option and
change the number as
required.
Making a Call from the Phonebook
You can store frequently-dialed phone numbers with a name in
the SIM card or the phone memory, using the phonebook. You
then simply select the required name to recall the associated
number. For further details on the Phonebook features, refer to
Adjusting the Volume
During a call, if you want to adjust the earpiece volume, use the
keys on the left side of the phone. Press the
increase and the key to decrease the volume.
key to
In idle mode, you can adjust the key volume using the
keys.
and
Call Functions
27
Answering a Call
When somebody calls you, the phone rings and the following
screen appears on each display.
If the caller can be identified, the caller’s phone number or name,
if stored in your phonebook, is displayed.
1. Press the
incoming call.
key or the Accept soft key to answer the
2. If the Anykey Answer option in the Extra Settings menu (Menu
5.6.2) is checked, you can press any key to answer a call
except for the
key and the Reject soft key (see
3. End the call by pressing the
key.
Note: You can answer a call while using the phonebook or menu
features.
Viewing Missed Calls
If you are unable to answer a call for any reason, you can find out
who was calling you, provided that this service is available. This
option provides the ability to call the person back, if necessary.
The number of missed calls is displayed on the idle screen
immediately after a call was missed.
Call Functions
28
To view the missed call immediately
1. Press the View soft key.
2. The number corresponding to the most recent missed call is
displayed, if available.
To....
Then press the...
Scroll through the missed
calls
or
key.
Call the number displayed
key.
Edit or delete a missed call Select soft key (see
number
next page).
Editing a Missed Call Number
Note: If the number corresponding to the missed call is not available, the
Edit Number option is not displayed.
1. Press the Options soft key.
2. Press the
or
key to highlight the Edit option.
3. Press the Select soft key.
4. Change the number as required. Press the Save soft key. If no
change is required press the Exit soft key.
Call Functions
29
To...
Then press the...
Call the number
key.
Store the number
Save soft key and enter the
name and location required
(for further details, refer to
page 35).
Deleting a Missed Call
1. Press the Options soft key.
2. If necessary, press the
option.
or
key to highlight the Delete
3. Press the Select soft key to go to the Options menu
You can press the
feature.
key at any time to exit the Missed Call
Note: You can access the Missed Call feature at any time by selecting
Switching Quickly to the Silent Mode
The Silent Mode is convenient when discretion is required and
you a wish to stop the phone from making any noise, in a theater
for example.
In idle mode, to switch your phone quickly to the silent mode,
simply press and hold down the
message and vibration icon
key until the “Silent Mode”
are displayed.
Call Functions
30
In the silent mode, your phone changes the sound settings as
follows.
Option
New Setting
Alert Type (Menu 4.3)
Light Only
Melody
Vibration
Vibra+Melody
Keypad Tone (Menu 4.4)
Off
Cool
Piano
Tone
Beep
SMS Tone (Menu 4.5)
Off
Tone 1-10
Power On/Off (Menu 4.6)
Off
Classical
Cheerful
Extra Tones (Menu 4.7.1)
Error Tone
Minute Minder
Connect Tone
To exit the silent mode and reactivate the previous Sound
Settings, press and hold the key again until “Exit Silent Mode”
appears. The vibration icon ( ) is no longer displayed.
Call Functions
31
Call Functions
32
Selecting Functions and Options
Your phone offers a set of functions that allow you to customize
your phone. These functions are arranged in menus and sub-
menus, accessed via the two soft keys marked
and
.
Each menu and sub-menu allows you to view and alter the
settings of a particular function.
The roles of the soft keys vary according to the current context; the
label on the bottom line of the display just above each key
indicates its current role.
To view the various functions/options available and select the one
required, proceed as follows.
1. Press the appropriate soft key.
To...
Then press the...
Select the:
• Function displayed
or
Select soft key or the
key.
• Option highlighted
View the next function or
highlight the next option in
a list
key or
key on the
left side of the phone.
Move back to the previous
function or option in a list
key or
key on
the left side of the phone.
Move back up one level in
the structure
key,
soft key or
key.
Selecting Functions and Options
33
To...
Then press the...
Exit the structure without
changing the settings
key.
In some functions, you may be asked for a password or PIN.
Enter the required code and press the OK soft key.
Example: Setting the Display Language
1. When the idle screen is displayed, press the Menu soft key to
access the menus.
2. Scroll through the menus until you reach the Phone Settings
menu, by pressing the
or
key.
3. To select the Phone Settings menu, press the Select soft key
or the key.
Note: If the menu name is too long for the display, will scroll when
highlighted.
4. Scroll through the sub-menus until you reach the Language
sub-menu, by pressing the
or
key.
5. To view the languages available, press the Select soft key or
the key. The current setting is highlighted.
6. Scroll through the list of languages until the appropriate one is
highlighted, by pressing the
or
key.
7. Press the Select soft key or the
key to confirm your
selection.
8. Press the
or
key twice to exit the menu structure.
Selecting Functions and Options
34
Phonebook
You can store phone numbers and their corresponding names in
the memory of your SIM card. In addition, you can store up to
1000 numbers in the phone memory. The SIM card and phone
memories, although physically separate, are used as if they were
a single entity, called the phonebook.
Storing a Number with a Name
There are two ways to store a number:
● Using the Save soft key in idle mode
● Using the New Entry option in the Phonebook menu
Storing a Number in Idle mode
As soon as you start to enter a number, Save appears above the
left soft key to allow you to store the number in the phonebook.
1. Key in the number to be stored.
Note: If you make a mistake while entering a number, correct it using the
2. When you are sure that it is correct, press the Save soft key.
3. Select an entry type to identify the category of number to be
stored. Four categories are available:
● Mobile Number
● Work Number
● Home Number
4. To select the category, press the
or
key, followed by
the Select soft key.
Phonebook
35
5. Enter a name and press the OK soft key.
The maximum length of a name depends on your SIM card. For
The phone now displays the first free location in the last memory
used to save a number and name. If that memory is full, the first
free location in the other memory is displayed.
Note: If you change phones, any numbers stored in your SIM card
memory will automatically be available with the new phone, whereas any
numbers stored in the phone memory must be restored.
6. Press the right soft key, labeled To Card or To Phone to toggle
between the phone and card memories.
7. If you do not want to save the number and name in the
suggested location, press the
key to clear the location
number and enter your preferred location by pressing the
number keys.
8. Press the OK soft key to store the name and number.
9. After storing, the phone displays the phonebook entry or name
just created.
To...
Then press the...
Use the entry options
Options soft key.
Return to the idle screen
key.
Storing a Number Using the Phonebook Menu
1. When the idle screen is displayed, press the Name soft key.
Phonebook
36
2. Scroll to New Entry by pressing the or
key and press
the Select soft key.
3. Select an Entry Type to identify the category of the number to
be stored. The following four options are provided:
● Mobile Number
● Work Number
● Home Number
● E-mail Address
Note: The E-mail icon is available in this step. It allows you to save an E-
mail address instead of a phone number.
number.
Using Phonebook Entry Options
While accessing any phonebook entry, press the Options soft key
to access the options for the entry.
To...
Then press the...
Select the
highlighted option
Select soft key or the
key.
Highlight a different
option
or
key until the
required option is highlighted.
The following options are available.
● Paste: allows you to paste the selected number into the
normal dialing mode. Use this option to dial a number
similar to one in the phonebook, a different extension in the
Phonebook
37
same office, for example.Use the
key to change the
When you are ready to dial, press the key.
● Edit: allows you to edit One Entry or All Entry. Select the
name and number and press the Select soft key.
● Delete: allows you to erase the selected name and number
from the phonebook. You are asked to confirm that you wish
to erase the name and number by pressing the Yes soft key.
● Copy: allows you to copy the selected number to another
location. Use this option to store a number similar to one
already in memory; once copied, edit the number and store it
in the phonebook.
● Caller Group: allows you to assign the entry to a caller group
so that the phone alerts you in a particular way when the
corresponding person calls you. Select one of the ten groups
available. To remove an entry from a group, select the No
Group option. For more information on how to change caller
group properties, see page 40.
● Add Entry: allows you to add a new number in a different
category (mobile, office, home or E-mail) to the currently
selected name. A phonebook entry or name can contain up
to four numbers, one in each category.
Searching for and Dialing a Number in the Phonebook
After storing numbers in the phonebook, you can search for them
in two ways: by name and by caller group.
Phonebook
38
Searching for a Number by Name
1. When the idle screen is displayed, press the Ph.Book soft key
when Search is highlighted. You are asked to enter a name.
2. Enter the start of the name that you wish to find.
3. The phonebook entries are listed, starting with the first entry
matching your input. This entry is also highlighted.
To...
Then press the...
View the highlighted entry View soft key.
Select a different entry
or
key until the
required entry is
highlighted.
Look for a name starting To clear previously entered
with a different letter
text, press the
Key
labeled with the required
letter.
4. Once you have found the required entry, press the
key to
dial the number, or press the Options soft key to access the
phonebook entry options; for further details, see page 37.
Searching for a Number by Caller Group
1. When the idle screen is displayed, select the Ph.Book soft key
to scroll to Group Search by pressing the
or
key and
press the Select soft key. You are asked to enter a group
name.
Phonebook
39
2. Enter the start of the group name that you wish to find.
3. The caller groups are listed, starting with the first group
matching your input. The group is also highlighted.
4. Scroll to the required group by pressing the
or
key
and press the View soft key.
5. The phonebook entries in the selected caller group are listed.
To...
Then press the...
View soft key.
View the highlighted
entry
Select a different entry
or
key until the
required entry is
highlighted.
6. Once you have found the required entry, press the
key to
dial the number, or press the Options soft key to access the
phonebook entry options; for further details, see page 37.
Editing a Caller Group
1. When the idle screen is displayed, select the Ph.Book soft key
to scroll to Group Edit by pressing the
or
key and
press the Select soft key.
2. Enter the start of the required group name or scroll through the
group list by pressing the or key.
3. When the required group is highlighted, press the Options soft
key.
Phonebook
40
4. Select each option and change the settings, as required. The
following options are available.
● Call ring tone: allows you to select the ring tone to be used
when you receive a voice call from a person in the group.
● SMS tone: allows you to select the ring tone to be used when
you receive a text message from a person in the group.
● Graphic: allows you to select the graphic icon to be
displayed when you receive a voice call from a person in the
group.
● Group Name: allows you to assign a name to the group; for
further details on how to enter characters, see page 45.
5. When you have finished, press the
or
key.
Speed-Dialing
Once you have stored phone numbers in the SIM card, you can
set up to eight speed-dial entries and then dial them easily
whenever you want, simply by pressing the associated number
key.
Setting Up Speed-Dial Entries
1. When the idle screen is displayed, select the Ph.Book soft key
to scroll to Speed Dial by pressing the or
key and press
the Select soft key.
2. Select the key to which you wish to assign the speed-dialing
feature (keys to ) and press the OK soft key.
Note: If you have already assigned a number to the key, the Options soft
key replaces the OK soft key. Go to Step 6.
Phonebook
41
3. Select the required phonebook entry from the list and press the
View soft key.
4. Select the required number if the entry has more than one
number, by pressing the
soft key.
or
key and press the Select
5. Once you have assigned a number to the selected key, four
options are available:
● Change: allows you to assign a different number to the key.
● Delete: allows you to clear the setting so that no number is
assigned to the key.
● Delete All: allows you to clear the settings for all keys so that
no numbers are assigned to any of the keys.
● Number: allows you to view the number assigned to the key.
6. When you have finished, press the
or
key.
Speed-Dialing from the Phonebook
To speed-dial the numbers assigned to keys to , press and
hold down the appropriate key.
Note: Memory location 1 is reserved for your Voice Mail server number
and cannot be changed.
Deleting All Phonebook Entries
You can delete all of the entries in the selected memory or both
memories.
1. When the idle screen displays, press the Ph.Book soft key.
2. Scroll to Delete All by pressing the Up or Down key and press
the Select soft key.
Phonebook
42
3. To place a check mark on the memory you want to empty,
ALL, SIM or Phone, press the Mark soft key.
You can remove the check mark by pressing the Unmark soft key.
4. When you are finished marking, press the Delete soft key to
delete the entries in the selected memory.
5. Enter the phone password and press the OK soft key.
Note: The password is preset to “00000000’ at the factory.
6. When the confirming message appears, press the Yes soft
key.
7. When you finish deleting, press the
or the
key.
Checking Memory Status
You can check how many names and numbers are stored in the
phonebook (card and phone memories) or how many free
locations remain.
1. When the idle screen is displayed, select the Ph.Book soft key
to scroll to Memory Status option pressing the 7 or key and
press the Select soft key.
2. When the idle screen is displayed, select the
3. Press the
or
keys to view the number of existing and
remaining entries in the card and phone memories.
Phonebook
43
Phonebook
44
Entering Text
When using your phone, you will often need to enter text. For
example, when storing a name in the phonebook, creating your
personal greeting or scheduling events in your calendar. You can
enter alphanumeric characters by using your phone’s keypad.
You are provided with the following text input modes.
● T9 mode: This mode allows you to enter words with only
one keystroke per letter. Each key on the keypad has more
than one letter – when you press the key once, J, K or L
may be displayed. The T9 mode automatically compares
your keystrokes with an internal linguistic dictionary to
determine the correct word, thus requiring far fewer
keystrokes than the traditional upper/lower-case character
modes.
● Upper/lower-case character modes: These modes allow you
to enter letters by pressing the key labeledlabeled with the
required letter once, twice, three or four times until the letter
is displayed.
● Number mode: This mode allows you to enter numbers.
● Symbol mode: This mode allows you to enter symbols,
such as punction marks.
Changing the Text Input Mode
When you are in a field that allows characters to be entered, you
will notice the text input mode indicator in the display.
Entering Text
45
To select the...
Then press the
until...
soft key
T9 mode
displays.
Alphabet mode
Symbol mode
abc displays
The symbol list displays.
Number mode
1 is displayed.
Using the T9 Mode
The T9 predictive text input mode allows you to key in any
character using single keystrokes. This text input mode is based
on a built-in dictionary.
1. When you are in the T9 predictive text input mode, start
entering a word by pressing keys to . Press each key
only once for one letter.
Example:to enter HELLO in the T9 mode,
press
,
,
,
and
.
The word that you are typing appears in the display. It may
change with each key that you press.
2. Enter the whole word before editing or deleting the keystrokes.
3. If the word is correct, start entering the next word.
4. Otherwise, press the
,
or
key repeatedly to display
alternate word choices for the keys that you have pressed.
Entering Text
46
Example:both OF and ME have the sequence and . The
phone displays the most commonly used choice first.
5. Complete each word with a space by pressing the
key.
● To type words not found in the T9 mode, change the text
input mode to the upper/lower-case character input mode.
● To enter full stops, hyphens or apostrophes, press the key.
The T9 mode applies grammar rules to ensure that the
correct punctuation is used.
● To change the case in the T9 mode, use the * key.
● You can move the cursor by using the
delete letters, press the key. Press and hold down the
key to clear the display.
and
keys. To
Using the Upper/Lower-Case Character Mode
Use the to keys to enter your text.
1. Press the key labeled with the required letter:
● Once for the first letter
● Twice for the second letter, and so on
2. Select the other letters in the same way.
Note: The cursor moves to the right when you press a different key. When
entering the same letter twice or a different letter on the same key, just
wait for a few seconds for the cursor to move right automatically, and
then select the next letter.
Entering Text
47
Refer to the table below for more information about the characters
available.
Key
Lower Case
Upper Case
Space
● To insert a space, press the
key.
● You can move the cursor by using the
delete letters, press the key. Press and hold down the
key to clear the display.
and
keys. To
Using the Symbol Mode
The symbol mode enables you to insert symbols in a text
message.
Use the navigation keys to scroll to the desired symbol and then
press OK soft key to insert the highlighted symbol into your
message.
Entering Text
48
Entering Text
50
In-Call Options
Your phone provides a number of control functions that you can
use during a call.
Putting a Call on Hold
You can place the current call on hold whenever you want. You
can make another call while you have a call in progress if this
service is supported by the network. Of these two calls, one is
active and the other is on hold and you can switch between the
calls.
To place a call on hold, simply press the Hold soft key. You can
reactivate the call whenever you want, by pressing the Unhold
soft key.
To make a call while you have a call in progress, proceed as
follows.
• Key in the phone number that you wish to dial or look it up
in the phonebook.
1. Press the
key to dial the second call.
2. The first call is automatically put on hold.
Or alternatively, proceed as follows.
1. Put the current call on hold by pressing the Hold soft key.
2. Make the second call in the normal way.
To swap between the two calls, simply press the Swap soft key.
The current call is placed on hold and the call on hold is
reactivated so that you can continue conversing with the other
party.
In-Call Options
51
When you have finished, end each call normally by pressing the
key.
Switching the Microphone Off (Mute)
You can temporarily switch your phone’s microphone off, so that
the other party cannot hear you.
Example: You wish to say something to another person in the
room but do not want the other party to hear you.
To switch the microphone off temporarily, proceed as follows.
1. Press the Options soft key.
2. If necessary, press the
key to highlight the Mute option.
3. Press the OK soft key.
The other party can no longer hear you.
To switch the microphone back on, proceed as follows.
1. Press the Options soft key.
2. If necessary, press the key to highlight the Unmute option.
3. Press the OK soft key.
The other party can hear you again.
Muting/Sending DTMF
These options allow you to turn the key tones off or on. If the
Mute keys option is selected, your phone does not transmit the
key tones. It allows you to press keys without hearing annoying
key tones during a call.
Note: To communicate with answering machines or computerized
telephony systems, the Send keys option must be selected.
In-Call Options
52
Searching for a Number in the Phonebook
You can search for a number in the phonebook during a call.
1. Press the Options soft key.
2. Press the
key to highlight the Phonebook option.
3. Press the OK soft key.
The phonebook entries are listed.
4. Enter the name that you wish to find.
If you enter the start of the name, the phonebook entries are listed,
starting with the first entry matching your input. The entry is also
highlighted.
5. To view the highlighted entry, press the Options soft key.
For a more detailed description of the Phonebook feature, refer to
page 38.
Answering a Second Call
You can answer an incoming call while you have a call in
progress, if this service is supported by the network and you have
set the Call Waiting menu option (Menu 7.2) to Activate (see
page 110). You will be notified of an incoming call by a call
waiting tone.
To answer a call while you have a call in progress, proceed as
follows.
1. Press the
key to answer the incoming call. The first call
is automatically put on hold.
2. To switch between the two calls, press the Swap soft key.
In-Call Options
53
To end a held call, press the Options soft key and select the End
Held Call option.
3. To end the current call, press the
key.
Making a Multiparty Call
A multiparty call is a network service that allows up to six people
to take part simultaneously in a multiparty or conference call. For
more information, contact your service provider.
Setting up the Multiparty Call
1. Call the first participant in the normal way.
2. Call the second participant in the normal way. The first call is
automatically put on hold.
3. To join the first participant to the multiparty call, press the
Options soft key and select the Join option.
4. To add a new person to the multiparty call, call the person in
the normal way, then press the Options soft key and select
the Join option.
You can add incoming callers by answering the call and pressing
Options, followed by Join. Repeat as required.
Having a Private Conversation With One Participant
1. Press the Options soft key and choose the Select one
option.
The list of call participants appears.
2. Highlight the required person, by pressing the
or
key,
followed by the Select soft key or the
key.
In-Call Options
54
3. Select the Private option.
Now you can talk privately with that person. The other
participants can continue to converse with each other.
4. To return to the multiparty call, press the Options soft key and
select Join.
All the multiparty call participants can now hear each other.
Dropping One Participant
1. Press the Options soft key and choose the Select one
option.
The list of call participants appears.
2. Highlight the required person, by pressing the
or
key,
followed by the Select soft key or the
key.
3. Select Remove.
The call is ended with that participant, but you can continue to
talk with the other participants.
4. End the multiparty call by closing the phone or pressing the
key.
In-Call Options
55
In-Call Options
56
Using the Menus
The phone offers a range of functions that allow you to tailor the
phone to your needs. These functions are arranged in menus and
sub-menus.
The menus and sub-menus can be accessed by scrolling with the
navigation keys or by using the shortcuts.
Accessing Menu Functions by Scrolling
1. In idle mode, press the Menu soft key to access the menu
facility.
2. Scroll with the
menu, Phone Settings for example. Press the Select soft key
or the key to enter the menu.
or
key to reach the required main
3. If the menu contains any sub-menus, Language for example,
you can access them by scrolling with the
or
key and
pressing the Select soft key.
If the menu that you have selected contains further options, repeat
the same procedure.
To...
Then press the...
Scroll through the menus
or
key or use
the
and keys on
the left side of the phone.
Confirm the chosen
setting
Select soft key or the
key.
Using the Menus
57
To...
Then press the...
Return to the previous
menu level
soft key.
Exit the menu without
changing the settings
key.
Accessing Menu Functions by Using Shortcuts
The menu items (menu, sub-menus and options) are numbered
and can be accessed quickly by using their shortcut number. The
shortcut number is shown in the bottom right next to the
soft
key on the display. Simply press the Menu soft key and key in the
required number.
Example: Accessing the Language option.
1. Press the Menu soft key.
2. Press
3. Press
for Phone Settings.
for Language.
The languages available are displayed directly.
Note: The numbers assigned to each menu option are indicated in the
depends on the services supported by the SIM card.
Using the Menus
58
List of Menu Functions
The following illustration shows the menu structure available and
indicates the:
● Number assigned to each option
● Page on which you can find a description of each feature
Note: If you use a SIM AT card that provides additional services, the SIM
AT menu (x) is displayed first when you press the Menu soft key to enter
the menu facility. For further details, refer to your SIM card
documentation.
1. Text Messages (see page 59)
1.1 Inbox
1.2 Outbox
1.3 Write New
1.4 Templates
1.5 Settings
*
1.5.1 T-Mobile
1.5.2 Setting 2
1.5.3 Setting 3
1.5.4 Setting 4
*
*
*
1.5.5 Common Setting
1.6 Delete All
1.7 Memory Status
1.7.1 SIM memory
1.7.2 PHONE memory
1.7.3 CB memory
1.8 Voice Mail
1.8.1 Call Voice Mail
1.8.2 Voice Server Number
1.9 Broadcast (If supported)
1.5.1 Read
1.5.2 Receive
1.5.3 Channel List
*.
Shown only if supported by your SIM card.
Using the Menus
59
1.5.4 Language
2. Picture Messages (see page 73)
2.1 Inbox
2.2 Outbox
2.3 Draft
2.4 Write New
2.5 Templates
2.6 Delete All
2.7 Memory Status
3. Call Records (see page 73)
3.1 Missed Calls
3.2 Incoming Calls
3.3 Outgoing Calls
3.4 Delete All
3.5 Call Time
3.5.1 Last Call
3.5.2 Total Outgoing
3.5.3 Total Incoming
3.5.4 Reset Timers
4. Sound Settings (see page 85)
4.1 Ring Tone
4.2 Ring Volume
4.3 Alert Type
4.4 Keypad Tone
4.5 Message Tone
4.5.1 SMS Tone
4.5.2 SMS-CB Tone
4.6 Power On/Off
4.6.1 Off
4.6.2 Classical
4.6.3 Cheerful
4.7 Extra Tones
4.7.1 Error Tone
Using the Menus
60
4.7.2 Minute Minder
4.7.3 Connect Tone
5. Phone Settings (see page 89)
5.1 Display Settings
5.1.1 Wallpaper
5.1.1.1 Wallpaper List
5.1.1.2 Text Color
5.1.2 Menu Style
5.1.2.1 Bar Style
5.1.2.2 Page Style
5.1.3 Auto Key Lock
5.1.3.1 OFF
5.1.3.2 15 seconds
5.1.3.3 30 seconds
5.1.3.4 1 minute
5.1.3.5 2 minutes
5.1.4 Brightness
5.1.5 Backlight
5.1.5.1 Off
5.1.5.2 15 Seconds
5.1.5.3 30 Seconds
5.1.5.4 1 Minute
5.1.5.5 3 Minutes
5.1.5.6 10 Minutes
5.1.6 Auto Light
5.1.6.1 Disable
5.1.6.2 Enable
5.1.7 Service Light
5.1.7.1 Off
5.1.7.2 Service Light1
5.1.7.3 Service Light2
5.1.7.4 Service Light3
5.2 Greeting Message
5.3 Own Number
5.4 Language
5.4.1 English
5.4.2 Francais
Using the Menus
61
5.4.3 Espanol
5.4.4 Automatic
5.5 Security
5.5.1 PIN Check
5.5.2 Change PIN
5.5.3 Phone Lock
5.5.4 Change Password
5.5.5 FDN Mode*
5.5.6 Change PIN2*
5.6 Extra Settings
5.6.1 Auto Redial
5.6.2 Anykey Answer
5.7 Short Cut
5.7.1 Key Up
5.7.2 Key Down
5.7.3 Key Right
5.7.4 Key Left
5.8 Reset Settings
6. Organizer (see page 99)
6.1 Alarm
6.1.1 Once Alarm
6.1.2 Daily Alarm
6.1.3 Morning Call
6.1.4 Remove Alarm
6.1.5 Autopower
6.2 Calendar
6.3 Time & Date
6.3.1 Set Time
6.3.2 Set Date
6.3.3 World Time
6.3.4 Time Format
6.4 Calculator
6.5 To Do List
6.6 Voice Memo
6.6.1 Record
6.6.2 Memo List
6.6.3 Delete All
Using the Menus
62
6.7 Currency Exchange
7. Network Services (see page 109)
7.1 Call Forwarding
7.1.1 Forward Always
7.1.2 Busy
7.1.2.1 Voice Calls
7.1.2.2 Data Calls
7.1.3 No Reply
7.1.3.1 Voice Calls
7.1.3.2 Data Calls
7.1.4 Unreachable
7.1.4.1 Voice Calls
7.1.4.2 Data Calls
7.1.5 Cancel All
7.2 Call Waiting
7.2.1 Voice Calls
7.2.2 Data Calls
7.2.3 Cancel All
7.3 Network Selection
7.3.1 Automatic
7.3.2 Manual
7.4 Caller ID
7.4.1 Default
7.4.2 Hide Number
7.4.3 Send Number
8. Funbox (see page 113)
8.1 t-Zones
8.1.1 Home
8.1.2 Favorite
8.1.3 http://
8.1.4 Clear Cache
8.1.5 Push Message
8.2 Games
8.2.1 BubbleSmile
8.2.2 Fun2Link
Using the Menus
63
8.2.3 MobileChess
8.2.4 Ultimate Golf Challenge
8.3 Sounds
8.4 Images
8.5 Delete All
8.6 Memory Status
8.6.1 Games
8.6.2 Sounds and Images
9. AIM
9.1 Sign On
9.2. Offline Convs.
9.3 Settings
9.3.1 Auto-Sign On
9.3.2 Change Password
9.3.3 Set AIM Sounds
9.4. Help
9.4.1 Sign Up
9.4.2 Sign On
9.4.3 Buddy List
9.4.4 Sending IMs
9.4.5 Receiving IMs
9.4.6 Privacy
9.4.7 Away Message
Text Messages
The SMS (Short Message Service) function is a network service
and may not be supported by your network. Messages can be
sent by text, fax, Email and paging messaging systems, provided
that these services are supported by your network. To send text
messages by phone, you must obtain the number of the SMS
centre from your service provider.
When the message icon (
text messages.
) appears, you have received new
Two message boxes are available.
Using the Menus
64
Inbox: used to store the messages that you have received.
Outbox: used to store the messages that you have already sent
or will send.
If the message memory is full, an error message is displayed
and you cannot receive any new messages.
Note: Use the Delete option in the Read Messages menu (Menu
1.1) to delete obsolete messages.
Reading a Message
1. Select the required box and press the Select soft key.
The list of messages in the box is displayed with the sender or
recipient’s phone number or name, if it is available in your
phonebook.
2. Select the required message and press the View soft key to
view the message contents.
3. To scroll through the message, press the
or
key.
While reading a message, you can choose the following options
by pressing the Options soft key.
Delete: allows you to delete obsolete messages.
Text Reply (inbox only): allows you to reply to the sender by
sending a text message. You can also change the SMS center
number, if required.
Call Back (inbox only): allows you to call the sender back.
Cut Number: allows you to extract a number from the message
text, so that you can call the number or save it in the phonebook.
Send: allows you to send a message that you have received or
saved. For further information on how to send a message, see
Using the Menus
65
Edit Message: allows you to edit a message.
Select Objects: allows you to save the objects, such as sounds
or images, from the message into your phone. You can then use
Note: The options available vary, depending on the message status
(new/old, not sent or sent for example).
Write New
Via this menu, you can write and send a text message.
Note: You can enter up to 918 alphanumeric characters for your
message. If you add objects to the message, the number of characters
you can enter will be decreased.
Creating a Simple Text Message
1. Create your message as required.
Note: For more information about entering characters, refer to page 47.
2. When you have completed your message, press the Options
soft key. The following options are available.
Send Only: allows you to send the message. The message will
be deleted after sending.
Save and Send: allows you to save a copy of the message and
then send the message to the required destination. You can read
the message in your outbox using the Read Messages option.
Save Only: allows you to save the message so that it can be
sent later. You can read the message in your outbox using the
Read Messages option.
Text Formatting allows you to select the following options:
Size, Underline, and Strike through.
Add Objects allows you to select the following objects:
Using the Menus
66
Sound, Melody, Picture, Animation.
Add Templates provides the ability to select from a list of
standard comments. You may edit these templates.
Add Phonebook allows you to search through your entries in your
phonebook.
Add Bookmark allows you to select from bookmarks you’ve
previously entered into your phone.
3. Select Send Only or Save and Send, and press the Select
soft key.
If you want just to save the message, select Save Only
.
After saving the message, the phone returns to the
Messages menu.
4. Enter a destination number and press the OK soft key. The
message is sent.
Creating a Message using the Options
1. Create your message as required.
2. Press the Options soft key.
3. Select one of the following options as required by using the
and
keys and pressing the Select soft key.
Text Formatting: allows you to format the style of the text. For
the Size attribute, the Normal, Large and Small sizes are
available. For the Underline and Strike through attributes, select
On or Off. The attributes can be combined.
Add Objects: allows you to add the required sound, melody
picture or animation to the message. Select the category of the
object to be added: Sound, Melody, Picture and Animation are
Using the Menus
67
available. In each category, you can select the various factory-set
items or choose an item received from other sources, such as the
Internet or other phones.
Add Templates: allows you to apply one of the preset message
templates to the text. Select one of the five messages predefined
via the Templates menu option (Menu 1.4); for further details,
Language: allows you to change the language to be used in the
T9 input mode. Select the language to be used.
4. Complete the message, and send or save it by following the
procedure from Step 2 on page 66.
Templates
Using this menu, you can preset up to nine messages that you
use most frequently. Scroll through the template list using the
and
keys. When the required message template is
highlighted, press the Options soft key.
Edit: allows you to write a new message or edit the selected
message.
Note: For further information on how to enter characters, refer to
page 47.
Send Message: allows you to recall the selected message. Once
you have completed the message, you can send, save and send,
or simply save it. For details on how to send a message, see
Delete: allows you to delete the selected message. You are
asked to confirm the deletion by pressing the Yes soft key.
Using the Menus
68
Settings
Via this menu, you can set up default SMS information. A setting
group is a collection of settings required to send messages. The
number of setting groups available depends on the capacity of
your SIM card.
Setting x (where x is the setting group number): each group has
its own sub-menu.
Service center: allows you to store or change the number of your
SMS center required when sending messages. You must obtain
this number from your service provider.
Default Type: allows you to set the default message type (Text,
Fax, Email and Paging). The network can convert the messages
into the selected format.
Default Validity: allows you to set the length of time for which
your text messages will be stored at the message center while
attempts are made to deliver them.
Setting Name: allows you to give a name to the setting group
currently being defined.
Common Setting: four options are available.
Reply Path: allows the recipient of your SMS message to send
you a reply message via your message center, if the service is
provided by the network.
Delivery Reports: allows you to activate or deactivate the report
function. When this function is activated, the network informs you
whether your message has been delivered or not.
Bearer Selection: allows you to choose between GSM and GPRS.
Delete All
This menu provides the option to delete messages saved on your
SIM or Phone for both your Inbox and Outbox. In addition, it also
Using the Menus
69
provides the option to delete CB Messages and by selecting the
All Messages, you are capable of deleting all at one time.
Memory Status
This menu shows how many messages are currently stored in the
SIM, phone and CB memories.
Voice Mail
This menu provides you with a way of accessing your voice
mailbox (if provided by your network).
The following options are available.
Call Voice Mail: before using this feature, you must enter the
voice server number obtained from your service provider (see
menu option 1.8.2). You can then select this option and simply
press the OK soft key to listen to your messages.
To quickly connect to the voice server, press and hold down the
key in idle mode.
Voice Server Number: allows you to change the voice mail
server number, if necessary.
To...
Then press the...
Enter the server
number
Corresponding numeric keys.
Correct a digit
key.
Move the cursor to
the left/right without
clearing the digit
or
key.
Note: Voice Mail is a network feature. Please contact your service
provider for more information.
Using the Menus
70
Broadcast
This network service allows you to receive text messages on
various topics, such as the weather or traffic. Messages are
displayed immediately they are received, provided that:
● The phone is in idle mode
● The Receive option is set to Enable
● The message channel is currently active in the channel list
The following options are available.
Read: lets you view the message. Volatile displays the
messages from the network, but loses its contents as soon as the
phone is switched off. Scroll through the message by using the
and
keys. While reading a message, press the Save soft
key to store the message in the Archive box for later retrieval.
Receive: allows you to enable or disable the reception of
broadcast messages.
Channel List: allows you to indicate the channels from which
you wish to receive broadcast messages. The following options
are available.
Select: used to enable or disable channels in the list by marking
or unmarking them respectively (a check mark is displayed in
front of each channel selected).
Add Channel: used to declare the ID and title for a new channel.
Delete: used to remove a channel from the list.
Edit: used to change the ID and title of an existing channel.
Language: allows you to select your preferred language to be
used when displaying cell broadcast messages.
Please contact your service provider for more information.
Using the Menus
71
Using the Menus
72
Picture Message
Multimedia Message Service (MMS) is a messaging
service very similar to Short Message Service
(SMS). It provides automatic and immediate
delivery of personal multimedia messages from
phone to phone or from phone to e-mail.
In addition to the familiar text content of text
messages, multimedia messages can contain
images, graphics, voice and audio clips. An MMS
message is a multimedia presentation in a single
entry. It is not a text file with attachments.
Using the MMS feature, your phone can receive
multimedia messages. You can also send picture
messages, which are short messages that contain
images, such as your photos or graphics you
downloaded from the Internet. This function is
available only if it is supported by your service
provider. Only phones that offer picture message
features can receive and display picture messages.
Inbox
Inbox
Viewing a Message When You Receive it
When a new multimedia message comes in, the
display shows the text notification along with the
sender’s number.
1. Press the View soft key to view the message.
Picture Message
73
The display shows brief information about the
message, such as the sender’s number, the
message size and the subject.
If you want to view the message later in the
Inbox, press the Exit soft key.
2. To scroll through the message information, press the Up or
Down key.
While viewing the information, press the Options soft key to use
the following options:
Retrieve: shows you the message contents.
Delete: deletes the message.
More Information: shows you detailed
information about the message.
Viewing a Received Message in the Inbox
When you access the Inbox menu option (Menu
2.1), the list of multimedia messages you received
displays with the senders’ phone numbers, if they
are available in your Phonebook, or subjects. The
icons on the left tells you the status of the
messages.
Messages you already read.
Messages you haven’t read yet.
1. Select a message and press the Select soft key
to view the message.
2. To scroll through the message, press the Up or
Down key.
3. Press the OK soft key on the message
Picture Message
74
presentation screen.
While viewing a message, you can choose the
Message options by pressing the Options soft key.
If you are viewing a new message, the options are
the same as when you view a message as soon as
you receive it. See the previous section.
When you are reviewing a message, the following
options are available:
Delete: deletes the message.
Reply: allows you to reply to the sender by sending
a text or picture message.
Callback: allows you to call the sender back.
Cut Address: allows you to extract the destination
number from the message, so that you can call the
number or save it in your Phonebook.
Forward: allows you to forward the message to
another person.
Save Picture: allows you to save an image from
the message into your phone. Images are stored in
the Pictures folder in the Fun Box menu option.
Save Sound: allows you to save a sound from the
message into the Sounds folder in the Fun Box
menu option.
Information: shows you information about the
message, such as subject, sender’s address,
message size, status and priority.
Picture Message
Picture Message
75
Outbox
When you access this menu option, the list of the
picture messages you sent or saved displays. The
icons on the left tells you the status of the
messages.
Messages currently being sent
Messages sent
Messages your phone couldn’t send
Messages to be sent
Messages forwarded
1. Select a message and press the Select soft key
to view the message contents.
2. To scroll through the message, press the Up or
Down key.
3. Press the OK soft key on the message
presentation screen.
While viewing a message, you can choose the
following options by pressing the Options soft key:
Delete: deletes the message.
Cut Address: allows you to extract the destination
number from the message, so that you can call the
number save it in your Phonebook.
Send: allows you to resend the message.
Edit Message: allows you to change the message
contents, sound, picture or text.
Picture Message
76
Information: shows you information about the
message, such as subject, recipient’s address,
message size, status and priority.
Picture Message
Write New
This menu option allows you to create a new picture
message and then send it to multiple destinations.
Creating and Sending a Picture Message
1. Enter the subject of your message and press the
OK soft key.
2. When Add Here highlights, press the Options
soft key and add the message contents using
one of the following options:
• Add Text: Enter the message text and press the OK soft key.
• Add Picture: allows you to add a picturestored in the
Pictures folder in the
• Fun Box menu option. Choose a picture and press the Select
soft key.Picture Message
• Add Sound: allows you to add a sound. You
can record a new voice memo or use a sound
stored in the Sounds folder in the
Fun Box menu option.
• Send: allows you to send the message. Use
this option when you finish creating the
message. This option is activated after you
add a content to the message.
Picture Message
77
• Save: saves the message in the Draft or Templates box for
later
use. This option is activated after you add a
content to the message.
• Settings: allows you to change the message
settings. For further details about each setting
option, see page 84. After changing, you need
to press the soft key or the
to back to the options screen.
key to go
• Add Destination: allows you to enter
destination addresses. See steps 7 to 10. After
adding, you need to press the soft key or
the
key to go to back to the options
screen.
• Preview: shows your message as it will
display on the recipient’s phone.
Note: You can use the adding options only one
time for one page.
3. When the added content displays, press the Down key to
highlight Add Here.
4. Repeat steps 2 and 3 until you finish creating your
message.
5. If you want to change the added items, press the Up or
Down key to highlight one and press the Options soft key.
The following options are available:
• Edit Text/Picture/Sound: allows you to change text or
replace the image or sound with another one.
Picture Message
78
• Add Page: allows you to add more pages. You
can move to each page using the Left or Right
key when Page highlights on the message
screen.
• Delete: deletes the item from your message.
• Duration: allows you to set how long one
page displays. After a specified length of time, the display
scrolls to the next page.
• Send: allows you to send the message.
• Save: saves the message in the Draft or Templates box for
later use.
• Settings: allows you to change the message
settings. For further details about each setting
• Add Destination: allows you to enter
destination addresses. See steps 7 to 10.
• Preview: shows your message as it will
display on the recipient’s phone.
Note: The options available are different
depending on the item selected on the
message screen.
6. When you finish creating the message, choose Send from
the options and press the Select soft key.
7. Choose one of the following options and press the Select
soft key:
• Phone Number: allows you to enter the phone number you
want.
Picture Message
79
• E-Mail: allows you to enter the e-mail address of the
recipient to send the message as an e-mail.
• Phone Book: allows you to recall a number from your
Phonebook.
8. Enter a number or an e-mail address, or select a number in
Phonebook.
9. When the correct number or address displays, press the OK
soft key.
10. To send the message to multiple destinations, select Add
Destination and press the Select soft key.
11. Repeat steps 7 to 10. You can enter up to 11 destinations.
If you want to edit the destinations, select one and press the
Select soft key. You can change or delete it. 12. When you are
finished entering the destinations, select Send Message and
press the Select soft key. Your phone sends the message.
Templates
This menu option stores up to five messages you saved as
templates. You can make a new message using the text of them.
Scroll through the template list using the Up and Down keys.
When the message template you want highlights, press the
Select soft key. The message text displays.
Press the OK soft key to use the following options:
Edit Message: allows you to send a message using the
template. For further details about how to send a message, see
page 79.
Delete: allows you to delete the message. You are asked to
confirm the deletion by pressing the Yes soft key.
Picture Message
80
Delete All
This menu option allows you to delete all of the picture messages
in each message box, Inbox, Outbox and Draft.
When a confirming message displays, press the Yes
soft key to confirm.
Memory Status
This menu option displays the pictures that you have maintained
in the memory of your phone. Use the Next soft key to rotate
through the pictures.
Picture Message
81
Picture Message
82
Call Records
Via this menu, you can view the phone calls:
● Missed
● Received
● Dialed
Note: You can access all numbers in the three types of call records by
pressing the
key in idle mode.
Missed Calls
This option lets you view the last 20 unanswered calls.
The number and name, if available, are displayed, together with
the date and time at which the call was received. By pressing the
Options soft key, you can:
● Edit the number if available and dial it or save it in the
phonebook
● Delete the call from the list
Incoming Calls
This option lets you view the last 20 phone calls answered.
The number and name, if available, are displayed, together with
the date and time at which the call was received. By pressing the
Options soft key, you can:
● Edit the number if available and dial it or save it in the
phonebook
● Delete the call from the list
Outgoing Calls
This option lets you view the last 20 numbers dialed.
Call Records
83
The number and name, if available, are displayed, together with
the date and time at which the call was made. By pressing the
Options soft key, you can:
● Delete the number
● Edit the number and save it in the phonebook
Delete All
This option lets you delete calls using the following options:
All Calls: All calls will be deleted, both incoming and outgoing.
Missed Calls: All missed calls will be deleted.
Incoming Calls: All incoming calls will be deleted.
Outgoing Calls: All outgoing calls will be deleted.
Call Time
This option lets you view the timers for calls made and received.
The following timers are available.
Last Call Time: length of the last call.
Total Outgoing: total length of all calls made since the timer
was last reset.
Total Incoming: total length of all calls received since the timer
was last reset.
Reset Timers: option used to reset the call timers; you must first
soft key.
Note: The actual time invoiced for calls by your service provider may
vary, depending on network features, rounding-off for billing purposes
and so forth.
Call Records
84
Sound Settings
You can use the Sound Settings feature to customise various
settings, such as the:
● Ring melody, volume and type
● Sounds made when you press a key, make an error or
receive a message
Note: When the phone is in the Silent mode (see page 32), you cannot
change the sound settings.
Ring Tone
This option allows you to select the required ring melody.
You can choose between many different melodies. Each time you
select a melody, it is played for a few seconds. If you have
downloaded any sounds from the Internet or EasyGPRS program
or received any ring tone messages, you can view the list in this
menu.
Ring Volume
This option allows you to adjust the ring volume to one of five
levels.
Use the
and
keys or the
and
keys on the left
side of the phone.
Alert Type
This option allows you to specify how you are to be informed of
any incoming calls.
The following options are available.
Light only: only the backlight is switched on; the phone neither
rings nor vibrates.
Melody: the phone rings using the ring melody selected via the
Sound Settings
85
Vibration: the phone vibrates but does not ring.
Vibra+Melody: the phone first vibrates three times and then
starts ringing.
Keypad Tone
This option allows you to select the tone that the keypad
generates when you press a key.
The following options are available.
Off: the keys do not make any sound.
Cool: each key, when pressed, makes the same sound but is a
different tone from the Beep option.
Piano: each key, when pressed, plays the piano melody.
Tone: each key, when pressed, makes a different sound.
Beep: each key, when pressed, makes the same sound.
Message Tone
This option allows you to select how the phone informs you that a
new message has been received.
SMS Tone
This option allows you to select how the phone informs you that a
new SMS message has been received.
The following options are available.
SMS Tone1~10: the phone uses an SMS tone. You are provided
with ten SMS tones.
OFF: the phone does not use the SMS tone.
Light Only: the service light at the top of the phone flashes.
Vibration: the phone vibrates.
Single Beep: the phone beeps once.
Sound Settings
86
SMS CB Tone
This option allows you to select how the phone informs you that a
new cell broadcast (CB) message has been received.
The following options are available.
OFF: the phone does not use the CB tone.
Light Only: the service light at the top of the phone flashes.
Vibration: the phone vibrates.
Single Beep: the phone beeps once.
SMS CB Tone1~10: the phone uses a CB tone. You are provided
with ten CB tones.
Power On/Off
Use this option to chose the sound you prefer when turning your
phone on or off. Three options are Off, Classical, and Cheerful.
Extra Tones
You can customise various other tones used by the phone.
To turn a given
tone...
Then press the...
On
Off
Mark soft key.
A check mark is displayed in
front of the option.
Unmark soft key again.
The check mark is no longer
displayed.
The following options are available.
Error Tone: sets whether the phone informs you that you have
made a mistake or not.
Sound Settings
87
Phone Settings
Many different features of your phone can be customised to suit
your preferences. All of these features are accessed via the Phone
Settings menu.
Display Settings
You can change the background image and the color of the
components in the display according to your preference.
Wallpaper
This option allows you to change the background image
(wallpaper) to be displayed in idle mode.
To change the background image, proceed as follows.
1. Scroll through the list by pressing the
or
key.
You have various preset images available. You can also select
the blank background and any images downloaded from the
Internet or the EasyGPRS program.
2. Press the Select soft key when the required image is
highlighted.
The selected image is displayed.
3. After viewing the image, press the Select soft key to display it
on the idle screen.
To change the Text Color, scroll through the list by pressing the
or
key. Select the color desired and press the Select soft
key.
Phone Settings
89
Menu Style
This option allows you to select the menu display style. You can
choose between Bar Style and Page Menu Style.
Auto Key Lock
When the Auto Key Lock feature is enabled, the phone keypad is
locked and you must press the Unlock soft key then press the *
key. The phone displays Keypad active.
If you wish to keep your phone unlocked, you must go into the
settings and change the option to OFF.
The following options are available.
OFF: the keypad is not locked.
15 Seconds: the keypad is locked after being idle for 15 seconds
30 Seconds: the keypad is locked after being idle for 30 seconds
1 Minute: the keypad is locked after being idle for 1 minute
2 Minutes: the keypad is locked after being idle for 2 minutes
Brightness
This option allows you to adjust the contrast of the display
screens to make them lighter or darker.
To adjust the display contrast, proceed as follows.
1. Adjust the contrast by using the
and
keys or the
and keys on the left side of the phone.
2. When you are satisfied, press the OK soft key to save the
selection.
Phone Settings
90
Back Light
You can select whether or not the phone uses the backlight. A
marginal increase in standby/talk time can be achieved by
turning the backlight off.
The following options are available.
OFF: the backlight is not used.
15 Seconds : the backlight comes on when you press a key or
receive a call and switches off 15 seconds after the last key is
pressed.
30 Seconds: the backlight comes on when you press a key or
receive a call and switches off 30 seconds after the last key is
pressed.
1Minute: the backlight comes on when you press a key or
receive a call and switches off 1 minute after the last key is
pressed.
3 Minutes: the backlight comes on when you press a key or
receive a call and switches off 3 minutes after the last key is
pressed.
10 Minutes: the backlight comes on when you press a key or
receive a call and switches off 10 minutes after the last key is
pressed.
Auto Light
Using this feature, you can specify the time for which the
backlight is to be used. This feature helps conserve your battery
power.
The following options are available.
Disable: the backlight is used according to the setting in the
Phone Settings
91
Enable: the backlight is used only during the specified period of
time. Set the required length of time in hours and minutes, using
the appropriate number keys.
Service Light
This option allows you to select whether or not the service light on
the top of the phone is used or in which color it flashes.
he following options are available.
Off: the service light does not display.
Service Light1: the service light displays red.
Service Light2: the service light displays green.
Service Light1: the service light displays orange.
Greeting Message
This option allows you to set a greeting message to be displayed
briefly when the phone is switched on. The current message is
displayed.
To...
Then press the...
Clear the existing
message
key and hold it down
until the message is cleared.
Enter a new message Appropriate alphanumeric
keys.
Change the text input
soft key.
mode
For further details on how to enter characters, refer to page 47.
Phone Settings
92
Own Number
This feature allows you to:
● Assign a name to each of your own phone numbers
registered on your SIM card
● Edit the names and numbers
This function is a memory aid, which you can use to check your
own phone numbers if you need to do so.
Any changes made here do not in any way affect the actual
subscriber numbers on your SIM card.
Language
You can select a display language. When the language option is
set to Automatic, the language is automatically selected
according to the language of the SIM card used.
Security
The Security feature enables you to restrict the use of your phone
to:
● The people of your choice
● The types of calls of your choice
Various codes and passwords are used to protect the features of
your phone.
PIN Check
When the PIN Check feature is enabled, you must enter your PIN
each time you switch the phone on. Consequently, any person
who does not have your PIN cannot use your phone without your
approval.
Note: Before disabling the PIN Check feature, you must enter your PIN.
Phone Settings
93
To change your PIN, refer to the Change PIN menu option
(Menu 5.5.6).
The following options are available.
Disable: the phone connects directly to the network when you
switch it on.
Enable: you must enter the PIN each time the phone is switched
on.
Change PIN
This feature allows you to change your current PIN to a new one,
provided that the PIN Check feature is enabled. You must enter
the current PIN before you can specify a new one.
Once you have entered a new PIN, you are asked to confirm it by
entering it again.
Phone Lock
When the Phone Lock feature is enabled, the phone is locked and
you must enter the 8-digit phone password each time the phone
is switched on.
The password is factory set to “00000000”. To change the phone
password, refer to the Change Password menu option.
Once the correct password has been entered, you can use the
phone until you switch it off.
The following options are available.
Disable: you are not asked to enter the phone password when
you switch the phone on.
Enable: you are required to enter the phone password when you
switch the phone on.
Phone Settings
94
Change Password
The Change Password feature allows you to change your current
phone password to a new one. You must enter the current
password before you can specify a new one.
The password is factory set to “00000000”. Once you have
entered a new password, you are asked to confirm it by entering it
again.
FDN Mode
The FDN (Fixed Dial Number) mode, if supported by your SIM
card, allows you to restrict your outgoing calls to a limited set of
phone numbers.
The following options are available.
Disable: you can phone any number.
Enable: you can only call phone numbers stored in the
phonebook. You must enter your PIN2.
Note: Not all SIM cards have a PIN2. If your SIM card does not, this menu
option is not displayed.
To change your PIN2, refer to the Change PIN2 menu option
(Menu 5.5.6) below.
Change PIN2
The Change PIN2 feature allows you to change your current PIN2
to a new one. You must enter the current PIN2 before you can
specify a new one.
Once you have entered a new PIN2, you are asked to confirm it
by entering it again.
Note: Not all SIM cards have a PIN2. If your SIM card does not, this menu
option is not displayed.
Phone Settings
95
Extra Settings
You can turn the automatic redialing or answering features on or
off.
To turn a feature...
Then press the...
On
ON soft key.
A check mark is displayed in
front of the option.
Off
OFF soft key.
The check mark is no longer
displayed.
The following options are available.
Auto Redial: when this option is checked, the phone makes up
to ten attempts to redial a phone number after an unsuccessful
call.
Note: The interval between two call attempts varies.
Anykey Answer: when this option is checked, you can answer
an incoming call by pressing any key, except the Reject soft key.
To reject the call, press the
key or the Reject soft key.
When this option is unchecked, you can only press the
key
or Accept soft key.
ShortCut
The navigation keys can be used as shortcut keys. When held
down in idle mode, they allow you to access specific menu
options directly.
To assign a shortcut to a key, proceed as follows.
Phone Settings
96
1. Select the key to be used as a shortcut key by pressing the
or
key, followed by the Select soft key.
Key up
(
)
Key down
Key right
Key left
(
)
)
(
(
)
2. Select the menu option to be assigned to the key by pressing
the or key.
Note: To deactivate a shortcut key, select the None option.
3. Press the Select soft key to save the selection.
Reset Settings
You can easily reset your phone to its default configuration. To do
so, proceed as follows.
1. Select the Reset Settings menu option.
2. Enter the 8-digit phone password and press the OK soft key.
Note: The password is preset to “00000000”. To change this password,
Phone Settings
97
Phone Settings
98
Organizer
The Organizer feature enables you to:
● View the calendar and organize your schedule
● Define a list of things to do
● Set the current date and time
● Set the alarm so that the phone rings at a specific time (to
remind you of an appointment for example)
● Use the phone as a calculator for basic mathematical
equations or currency exchange operations
Alarm
This feature allows you to:
● Set the alarm to ring at a specific time
● Set the phone to switch on automatically and ring the alarm
even if the phone is switched off (Autopower menu option
set to Enable)
The following options are available.
Once Alarm: the alarm rings only once and is then deactivated.
Daily Alarm: the alarm rings every day at the same time.
Morning Call: the alarm rings to wake you up in the morning.
To set the alarm, proceed as follows.
1. Choose the type of alarm to be set.
2. Enter the required time and day of the week, if applicable.
3. Press the OK soft key.
4. If you select Morning Call in Step 1, select the repeat option:
Monday to Friday or Monday to Saturday.
Organizer
99
Remove Alarm: deactivates all alarm settings.
Autopower: if this option is set to Enable, the alarm will ring at
the specified time, even when the phone is switched off.
If the menu option is set to Disable and the phone is switched off
at the specified time, the alarm will not ring.
To stop the alarm when it rings, press the Exit soft key.
When setting or viewing an alarm, the following options are
available when you press the Options soft key.
Remove Alarm: deactivates the current alarm.
Note: Alarm Sound Set: allows you to select the alarm melody
this option can be found in each of the Alarm options.
Calendar
With the Calendar feature, you can:
● Consult the calendar
● Write memos to keep track of your schedule and trigger an
alarm if necessary
Consulting the Calendar
When you select the Calendar menu option, the calendar is
displayed. The following options are available when you press
the Options soft key.
Search all: displays all memos set, regardless of the day and
starting with the oldest. To scroll through the memos, press the
or
key.
Delete all: allows you to delete all memos. You are asked to
confirm your action.
Organizer
100
Go to date: allows you to jump to a specific date.
Exit: exits the Calendar feature and returns to the idle mode.
Writing a Memo
To write or edit a memo on a specific date, proceed as follows.
1. Select the required date in the calendar, using the navigation
keys.
Note: To skip to the previous or next month, press the
on the left side of the phone.
and
keys
2. Press the Select soft key.
An empty memo screen is displayed to allow you to enter your
memo.
3. Enter your memo and then press the OK soft key.
Note: For further details on how to enter characters, refer to page 47.
You are asked if you wish to set the alarm.
4. If you want the alarm to ring on the chosen day, press the Yes
soft key.
Otherwise, press the No soft key.
5. If you pressed the Yes soft key, set the time for the alarm and
press the OK soft key.
The color of the date is changed to green to indicate that a
memo exists.
Editing a Memo
1. To edit a memo, selete the Calendar menu option.
Organizer
101
2. Select the date your memo is set to occur by using the right
and left arrow keys. Press the Select soft key.
3. Press the Options soft key.
4. Select the Edit menu option and edit the memo appropriately.
Note: I For further details about how to enter characters, refer to
page 47.
Once you have finished editing the memo, press the OK soft key.
The following options are then available when you press the
Options soft key.
Alarm: allows you to set the alarm to ring on the chosen day.
Delete: allows you to delete the memo.
Copy to: allows you to copy the memo to another date and/or
time.
Move to: allows you to change the date and/or time of the
memo.
Time & Date
This option allows you to change the current time and date
displayed. You can also check the current time for Greenwich
Mean Time (GMT) and 21 major cities around the world.
The following options are available.
Set Time: allows you to enter the current time. You can choose
the time format via the Time Format menu option (Menu 6.3.4).
Note: Before setting the time, you must specify your time zone, via the
World Time menu option (Menu 6.3.3).
Set Date: allows you to enter the day, month and year.
Organizer
102
World Time: allows you to check the current time for Greenwich
Mean Time (GMT) and 21 major cities around the world, using
the
and
keys.
The screen shows the:
● City name
● Current date and time
● Time difference between the selected city and your city if you
have set the local time (see below for further details) or GMT
(by default)
To select the time zone in which you are located, proceed as
follows.
1. Select the city corresponding to your time zone by pressing the
or
key one or more times.
The local date and time are displayed.
2. Press the Set soft key.
Time Format: allows you to change the time format to 24 Hours
or 12 Hours.
Calculator
With this feature, you can use the phone as a calculator. The
calculator provides the basic arithmetic functions: addition,
subtraction, multiplication and division.
Using the Calculator
1. Enter the first number using the numeric keys.
2. Press the right soft key until the required arithmetic symbol
appears: + (add), - (subtract), x (multiply), / (divide).
3. Enter the second number.
Organizer
103
Repeat Steps 1 to 3 as many times as required.
Notes:
• To erase any mistakes and clear the display, press the
key.
• To include a decimal point or a bracket, press the left soft key
until the required symbol is displayed.
4. To calculate the result, press the
key.
To Do List
This feature allows you to:
● Draw up a list of tasks to be done
● Assign a priority and deadline to each task
● Sort the tasks by priority and status mark
Creating the To Do List
1. Press the New soft key.
2. Enter the first task.
Note: You can enter up to 40 characters. For further details on how to
enter characters, see page 47.
3. Press the OK soft key.
4. Select high, normal or low priority using the
or
key
and press the Select soft key.
5. Enter your deadline.
If you do not want to set a deadline, press the Skip soft key.
6. Press the OK soft key.
Organizer
104
Editing the To Do List
If tasks are already defined in the To Do List when you select the
To Do List menu option (Menu 6.5), the current contents are
displayed with the status mark and priority (three stars for high,
two for normal and one for low).
The following options are available.
To...
Then...
View the details for Highlight the task.
a specific task
Press the View soft key.
Change the status Highlight the task.
of a specific task
Press the
key to mark the
task as completed as of the
current date and time.
or
Highlight the task.
Press the Options soft key.
Select the Mark option.
Select the appropriate status
(Done or Undo).
Create a new task Press the Options soft key.
Select the New option.
Enter the text, priority and
deadline for the task.
Edit an existing
task
Highlight the task.
Press the Options soft key.
Select the Edit option.
Change the text, priority and
deadline for the task.
Organizer
105
To...
Then...
Sort the existing
Press the Options soft key.
tasks by priority or Select the Sort option.
status
Select the sort criterion (High,
Low, Done or Undo).
Copy a task
Highlight the task.
Press the Options soft key.
Select the Copy option.
Change the text, priority and
deadline for the task as required.
Copy a task to the Highlight the task.
calendar
Press the Options soft key.
Select the Copy to calendar
option.
Change the text and deadline for
the task and set the alarm as
required.
Delete a task
Highlight the task.
Press the Options soft key.
Select the Delete option.
Delete all tasks
Press the Options soft key.
Select the Delete all option.
Confirm the deletion by pressing
OK.
Exit the To Do list Press the Options soft key.
Select the Exit option.
Organizer
106
Voice Memo
Voice Memo allows you to record voice messages for your
convenience. The following options are available.
To...
Then...
Record
Press the left soft key to BEGIN
recording. Once you have
completed the recording, press
the left soft key again to STOP the
recording. You can then
1. Replay
2. Re-record
3. Save
4. Quit
Memo List
To review the memo list select the
left soft key and use the
or
key to scroll through the
list of memos. Press the
Options soft key.
Delete All
Press the Select soft key.
This will delete all the voice
memos you have stored.
Currency Exchange
Using this menu option, you can make currency conversions.
1. Enter the current exchange rate of your source currency and
press the OK soft key.
Organizer
107
You can insert a decimal point by pressing the
key.
2. Enter the amount for which you wish to conduct the currency
conversion and press the OK soft key.
The exchange rate amount you entered and equivalent value are
displayed.
3. Press the Exit soft key to exit the currency convertor.
Organizer
108
Network Services
These menu functions are network services. Please contact your
service provider to check their availability and subscribe to them,
if you so wish.
Call Forwarding
This network service enables incoming calls to be rerouted to the
number that you specify.
Example:You may wish to forward your business calls to a
colleague while you are on holiday.
Call forwarding can be set up in the following ways.
Forward Always: all calls (Voice and Data) are forwarded to
the designated number. To activate press the Activate soft
key. To exit press the Exit soft key.
Busy: calls are forwarded if you are already making another call.
No Reply: calls are forwarded if you do not answer the phone.
Unreachable: calls are forwarded if you are not in an area
covered by your service provider.
Cancel All: all call forwarding options are cancelled.
You can specify individual forwarding options for each of the
following call types:
● Voice calls only
● Data calls only
Example:You can forward voice calls to your colleague if you
are already using the phone.
To set your call forwarding options, proceed as follows.
1. Select the type of call forwarding required by pressing the
or
key until the appropriate option is highlighted, and then
press Select.
Network Services
109
2. Select the type of calls to be forwarded by pressing the or
key until the appropriate option is highlighted and then
press Select.
The current status is displayed. If the option has already been set,
the number to which the calls are forwarded is displayed.
To...
Then...
Activate call
forwarding
Press the Activate soft key.
Go to Step 4.
Change the call
number
Press the Change soft key.
Go to Step 4.
Deactivate call
forwarding
Press the Remove soft key.
3. Enter the number to which the calls are to be forwarded and
press OK.
To enter the international code, press the
sign is displayed.
key until the +
The phone sends your settings to the network and the network’s
acknowledgement is displayed.
You can deactivate all call forwarding settings by selecting the
Cancel All option.
Call Waiting
This network service enables you to be informed when someone
is trying to reach you during another call.
You can specify individual call waiting options for each of the
following call types:
Network Services
110
● Voice calls only
● Data calls only
To set your call waiting options, proceed as follows.
1. Select the type of calls to which the call waiting option is to be
applied by pressing the or
key until the appropriate
option is highlighted and then press the Select soft key.
The screen informs you whether call waiting is activated or
deactivated.
2. You can activate or deactivate the call waiting feature as
necessary by using the Activate or Deactivate soft key
respectively.
To return to the previous screen, press the Exit soft key.
You can also deactivate all call waiting settings by selecting the
Cancel All option.
Network Selection
The Network Selection feature enables you to indicate whether the
network used when roaming (outside your home area) is
selected automatically or manually.
Note: You can select a network other than your home network only if it
has a valid roaming agreement with your home network.
To indicate whether the network is to be selected automatically or
manually when roaming, proceed as follows.
1. When Network Selection is displayed, press the Select soft
key.
2. Press the or
key until the appropriate option is
highlighted and then press the OK soft key.
Network Services
111
If you select Automatic, you are connected to the first available
network when roaming.
If you select Manual, the phone scans for the available networks.
Go to Step 3.
3. Press the or
key until the preferred network is
highlighted and then press the OK soft key.
You are connected to that network.
Caller ID
You can prevent your phone number from being displayed on the
phone of the person being called.
Note: Some networks do not allow the user to change this setting.
The following options are available.
Default: the default setting provided by the network is used.
Hide Number: your number is not displayed on the other
person’s phone.
Send Number: your number is sent each time you make a call.
Network Services
112
Funbox
The Funbox menu contains several fun options.
t-zones
Your phone is equipped with a WAP Browser to allow you to
access and navigate the Wireless Web via your phone. Using this
menu, you can use the WAP browser.
Home
Selecting this option connects the phone to the network and loads
the homepage of the Wireless Web service provider. You can also
press the
in Idle Mode.
Favorite
Selecting the Favorite option allows you to store the URL
addresses of your favorite Web sites. You can access this menu
directly by pressing and holding the # key while using the WAP
browser. To store a URL address:
1. Select an empty location and press the Options soft key.
2. Enter the address and press the Enter soft key.
3. Enter a name for the favorite item and press the Enter soft key.
After saving your favorite items, you can use the following options
by pressing the Options soft key:
Goto URL: quickly accesses you to the site
Edit: allows you to edit the address
Delete: deletes the address.
Funbox
113
http://
Selecting this option provides a starting point for you to enter the
web address you wish to reach.
Clear Cache
You can clear the information stored in the cache, the phone’s
temporary memory which stores the most recently accessed Web
pages.
Press the Yes soft key to confirm the deletion. Otherwise, press
the No soft key.
Push Message
In this menu option, you can receive and access web messages
from the server.
The following options are available:
Inbox: allows you to read the messages received from the web
server.
Receive: allows you to set whether or not your phone receives
web messages
Delete all: allows you to delete all of the web messages.
Games
You can enjoy three games with your phone.
Scroll to the required game, using the and
keys and press
the Select soft key. For further details on the game, refer to the
on-screen help.
Funbox
114
Sounds
In this menu, you can view the list of sounds downloaded from
the server. You can set the downloaded sounds as the current
ring tone, but cannot send the sounds to other phones.
When the memory is full, a warning message is displayed and
the phone rejects additional sounds until you erase obsolete
ones.
Images
In this menu, you can view the list of pictures downloaded from
the server. You can set the downloaded pictures as the current
background image, but cannot send them to other phones.
When the memory is full, a warning message is displayed and
the phone rejects additional pictures until you erase obsolete
ones.
Delete All
This option allows you to delete all games, sounds, and images
you have stored on your phone. To select one of these options,
press the left soft key to Mark your choice. Then press the right
soft key to Delete them.
Memory Status
This option displays the memory used for games, sounds, and
images. Press the Select soft key to view the following options:
Games:
Sounds and Images:
Funbox
115
Funbox
116
Solving Problems
Before contacting the after-sales service, perform the following
simple checks. They may save you the time and expense of an
unnecessary service call.
When you switch your phone on, the following messages
may appear
Insert SIM Card
● Check that the SIM card is correctly installed.
Phone Locked Enter Password
● The automatic locking function has been enabled. You must
enter the phone’s password before you can use the phone.
Enter PIN
● You are using your phone for the first time. You must enter
the Personal Identification Number supplied with the SIM
card.
● The option requiring that the PIN be entered each time the
phone is switched on was enabled. You must enter your PIN
and then disable this option if so required.
Enter PUK
● The PIN code was entered wrongly three times in succession
and the phone is now blocked. Enter the PUK supplied by
your network operator.
“No service,” “Network failure” or “Not done” is displayed
Solving Problems
117
● The network connection was lost. You may be in a weak
signal area (in a tunnel or surrounded by buildings). Move
and try again.
● You are trying to access an option for which you have not
taken out a subscription with your service provider. Contact
the service provider for further details.
You have entered a number but it was not dialed
● Have you pressed the
key?
● Are you accessing the right cellular network?
● You may have set an outgoing call blocking option.
Your correspondent cannot reach you
● Is your phone switched on (the
key pressed for more
than one second)?
● Are you accessing the right cellular network?
● You may have set an incoming call blocking option.
Your correspondent cannot hear you speaking
● Have you switched off the microphone?
● Are you holding the phone close enough to your mouth? The
microphone is located at the bottom of the phone.
The phone starts beeping and “**Warning** Low Battery” flashes
in the display
● The battery is insufficiently charged. Replace the battery and
recharge it.
The audio quality of the call is poor
● Check the signal strength indicator in the display (
number of bars indicates the signal strength from strong
) to weak ( ).
); the
(
Solving Problems
118
● Try moving the phone slightly or moving closer to a window
if you are in a building.
No number is dialed when you recall a phonebook entry
● Check that the numbers have been stored correctly, by using
the Phonebook Search feature.
● Re-store the number, if necessary.
Note: If the above guidelines do not enable you to solve
the problem, take a note of:
● The model and serial numbers of your phone
● Your warranty details
● A clear description of the problem
Then contact your local dealer or Samsung after-
sales service.
Solving Problems
119
Solving Problems
120
Access Codes
There are several access codes that are used by your phone and
its SIM card. These codes help you protect the phone against
unauthorized use.
When requested for any of the codes explained below, key in the
appropriate code (displayed as asterisks) and press the OK soft
key. If you make a mistake, press the
key one or more times
until the incorrect digit is cleared and then continue entering the
correct code.
The access codes, except for the PUK and PUK2 codes can be
for further details.
Important! Avoid using access codes resembling emergency
numbers, such as 911, so that you do not dial an emergency
number accidentally.
Phone Password
The Phone Lock feature uses the phone password to protect your
phone against unauthorized use. The phone password is
supplied with the phone and is factory set to 00000000.
To...
Refer to...
Activate/deactivate the
Phone Lock feature
Page 90
(Menu 5.5.3).
Change the phone
password
Page 90
(Menu 5.5.4).
Access Codes
121
PIN
The Personal Identification Number or PIN (4 to 8 digits) protects
your SIM card against unauthorized use. It is usually supplied
with the SIM card.
If you enter an incorrect PIN three times in succession, the code is
disabled and cannot be used until you re-enable it by entering the
PUK (see below).
To...
Refer to...
Check feature
(Menu 5.5.1).
Change the PIN
Page 94
(Menu 5.5.2).
PUK
The 8-digit PUK (Personal Unblocking Key) is required to change
a disabled PIN. The PUK may be supplied with the SIM card. If
not, or you have lost it, contact your service provider.
To re-enable your PIN, proceed as follows.
1. Key in the PUK and press the OK soft key.
2. Enter a new PIN of your choice and press the OK soft key.
3. When the Confirm New PIN message is displayed, key in the
same code again and press the OK soft key.
If you enter an incorrect PUK ten times in succession, the SIM
card becomes invalid. Contact your service provider for a new
card.
Access Codes
122
PIN2
The PIN2 (4 to 8 digits), supplied with some SIM cards, is
required to access specific functions, such as setting the
maximum cost of a call. These functions are available if
supported by your SIM card.
If you enter an incorrect PIN2 three times in succession, the code
is disabled and you cannot access the functions until you re-
enable it by entering the PUK2.
PUK2
The 8-digit PUK2 (Personal Unblocking Key 2), supplied with
some SIM cards, is required to change a disabled PIN2. If you
lose the code, contact your service provider.
To re-enable your PIN2, proceed as follows.
1. Key in the PUK2 and press the OK soft key.
2. Enter a new PIN2 of your choice and press the OK soft key.
3. When the Confirm PIN2 message is displayed, key in the
same code again and press the OK soft key.
If you enter an incorrect PUK2 ten times in succession, you will
not be able to access the functions requiring the PIN2. Contact
your service provider for a new card.
Access Codes
123
Access Codes
124
WAP Browser
Your phone comes equipped with a WAP (Wireless Application
Protocol) browser, making it possible for you to access the
Wireless Web.
About the WAP Browser
The WAP Browser allows you to:
● Access up-to-the minute information via your phone
● View specially designed text versions of popular Internet sites
including Yahoo!, CNN Mobile and the Weather Channel
Browsing the Wireless Web using your phone is unlike using your
computer, in that site provides have:
● Selected only the critical aspects of their site for wireless
phone users
● Removed most graphics
Each time you start the WAP Browser, the phone connects to the
Wireless Web and the service indicator icon appears on the
display to inform you that you are:
● Are connected to the Wireless Web
● Will be billed accordingly (rates vary according to your
service option)
The WAP Browser ends the network connection after a certain
period of inactivity and automatically reconnects as necessary.
For this reason, you may find that you are billed for several
network connections within a single session. This is normal and
is designed to minimize you bill.
Accessing the WAP Browser
To enter the t-zones menu to access the WAP browser:
WAP Browser
125
1. When the idle Screen is displayed, press the Menu soft key to
enter the menu mode.
2. Press the
or
until the Funbox menu option is
displayed, and then press the Select soft key. You can also
press the key directly.
3. Press the
or
key one or more times to highlight t-
zones, then press the Select soft key. You can also press the
1 key directly.
4. Press the
or
key one or more times to highlight the
required option and then press the Select soft key.
Option
Description
Home
http://
Connects the phone to the
network and loads the
homepage of the Wireless Web
service provider.
This option allows you to manually
enter the URL address of the Web
site that you wish to access. You
can access this menu directly by
pressing and holding down the
key in the WAP Browser.
WAP Browser
126
Option
Description
Allows you to store the URL
addresses of your favorite
Web sites. You can access
this menu directly by
Favorite
pressing and holding the
key while using the
WAP Browser. To store a URL
address, select an empty
location and enter the
address. Three submenus
are available. Select Go to
URL to access the site
quickly, Edit to edit the
selected address and
Delete to delete the
selected address.
Clears the information
stored in the cache (the
phone’s temporary
Clear Cache
memory used to store the
most recently accessed
Web pages).
WAP Browser
127
Option
Description
In this menu option, you
can receive and access
web messages from the
server. The following options
are available:
Push Message
Inbox: allows you to read
the messages received
from the web server.
Receive: allows you to set
whether or not your phone
receives web messages.
Delete All: allows you to
delete all of the web
messages.
Starting the WAP Browser
To start the WAP Browser when the idle screen is displayed press
the
key or press the Menu soft key, followed by the 8, 1 and
1 keys.
A connection is established with your service provider and the
corresponding homepage is displayed.
The content of the WAP Browser startup homepage depends on
your Wireless Web service provider. To scroll through the screen,
use the
and
keys.
Note: To access the startup homepage from any other screen in the
WAP Browser, use the Home option. For more information on the WAP
Browser menus, refer to...
WAP Browser
128
Exiting the WAP Browser
To exit the browser at any time, simply press the
key or
press and hold down the
key.
Using the WAP Browser
Using the Soft Keys
A bar containing browser commands is located at the bottom of
the WAP Browser display. The soft keys below the bar are used to
execute these commands. The two keys are called soft keys
because their functions changes depending on the WAP Browser
application in use.
Navigating the Wap Browser
To...
Then....
Scroll through and
select browser items
Press the
until the
and
key
symbol points
to the required item, and then
press the OK soft key to
confirm the selection.
Press the corresponding
numeric key.
Select a numbered
item
Press the Back soft key or
Return to the previous
page
the
key.
WAP Browser
129
To...
Then....
Select the Home menu
option; for more information
on this option, refer to.....
Return to the startup
homepage
Entering Text, Numbers or Symbols
When you are prompted to enter text, the current text entry mode
is indicated on the screen. The following modes are available.
Mode
Description
A/a
1
Allows you to enter letters in
the alphabet. Press the
corresponding key until the
required letter is displayed
Allows you to enter
numbers.
Note: To enter symbols, press the 1 key repeatedly until the required
symbol is displayed.
To...
Then....
Change modes
Press the
times.
key one or more
Enter a space
Press the
WAP Browser
130
To...
Then....
Set the cursor to the right of
the character to be
corrected
Edit text
Press the
key as
required.
Enter the correct
character(s).
Using and Selecting WAP Menu Options
Various menu options are available when you are using the WAP
Browser to navigate the Wireless Web.
To access a menu option, proceed as follows:
1. Press and hold down the
key. A menu is displayed.
2. Highlight the required menu option by pressing the
keys.
and
and
3. Select the option by pressing the Select soft key.
4. If necessary, select the secondary option using the
keys, and press the Select soft key to confirm.
Note: The menus may vary, depending on your version of the WAP
Browser.
Reload
This option reloads the current page.
WAP Browser
131
Home
This option takes you back at any time to the homepage of the
Wireless Web service provider.
Go to URL
This option allows you to enter manually the URL address of the
required Web page.
After entering an address, press the OK soft key to go there
directly.
Show URL
This feature displays the URL address of the site to which you are
currently connected. It also enables you to declare the current site
as the startup homepage.
To...
Press the...
Declare the current
Option soft key, select the Save
page as your startup to Home option and press
homepage
Select.
Option soft key, select the
Save to Bookmark option
and press Select.
Set a bookmark for
the current page
Back soft key.
Cancel your setting
WAP Browser
132
Health and Safety Information
Usage guidelines:
All about performance and safety
Getting the Most Out of Your Reception
The quality of each call you make or receive depends on the
signal strength in your area. Your phone informs you of the
current signal strength by displaying a number of bars next to the
signal strength icon. The more bars displayed, the stronger the
signal.
If you’re inside a building, being near a window may give you
better reception.
Understanding the Power Save Feature
If your phone is unable to find a signal after 15 minutes of
searching, a Power Save feature is automatically activated. If
your phone is active, it periodically rechecks service availability
or you can check it yourself by pressing any key. Anytime the
Power Save feature is activated, a message displays on the
screen. When a signal is found, your phone returns to standby
mode.
Understanding How Your Phone Operates
Your phone is basically a radio transmitter and receiver. When it’s
turned on, it receives and transmits radio frequency (RF) signals.
When you use your phone, the system handling your call controls
the power level. This power can range from 0.006 watts to 0.2
watts in digital mode.
Health and Safety Information
133
Knowing Radio Frequency Safety
The design of your phone complies with updated NCRP standards
described below.
In 1991-92, the Institute of Electrical and Electronics Engineers
(IEEE) and the American National Standards Institute (ANSI)
joined in updating ANSI’s 1982 standard for safety levels with
respect to human exposure to RF signals. More than 120
scientists, engineers and physicians from universities,
government health agencies and industries developed this
updated standard after reviewing the available body of research.
In 1993, the Federal Communications Commission (FCC)
adopted this updated standard in a regulation. In August 1996,
the FCC adopted hybrid standard consisting of the existing ANSI/
IEEE standard and the guidelines published by the National
Council of Radiation Protection and Measurements (NCRP).
Maintaining Your Phone’s Peak Performance
Note: For the best care of your phone, only authorized personnel should
service your phone and accessories. Faulty service may void the
warranty.
There are several simple guidelines to operating your phone
properly and maintaining safe, satisfactory service.
● Hold the phone with the antenna raised, fully-extended and
over your shoulder.
● Try not to hold, bend or twist the phone’s antenna.
● Don’t use the phone if the antenna is damaged.
● Speak directly into the phone’s receiver.
Health and Safety Information
134
Maintaining Safe Use of and Access to Your Phone
FAILURE TO FOLLOW THE INSTRUCTIONS OUTLINED MAY LEAD
TO SERIOUS PERSONAL INJURY AND POSSIBLE PROPERTY
DAMAGE
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE
INSTRUCTIONS.
DANGER - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
CAREFULLY FOLLOW THESE INSTRUCTIONS.
FOR CONNECTION TO A SUPPLY NOT IN THE U.S.A., USE AN
ATTACHMENT PLUG ADAPTOR OF THE PROPER CONFIGURATION
FOR THE POWER OUTLET.
Using Your Phone While Driving
Talking on your phone while driving is illegal in some states.
Even where it’s not, it can divert your attention from driving.
Remember that safety always comes first.
When using your phone in the car:
● Get to know your phone and its features, such as speed dial
and redial.
● When available, use a hands-free device.
● Position your phone within easy reach.
● Let the person you are speaking to know you are driving; if
necessary, suspend the call in heavy traffic or hazardous
weather conditions.
● Do not take notes or look up phone numbers while driving.
● Dial sensibly and assess the traffic; if possible, place calls
when you stationary or before pulling into traffic.
● Do not engage in stressful or emotional conversations that
may divert your attention from the road.
Health and Safety Information
135
● Dial 9,1,1 to report serious emergencies. It’s free from your
wireless phone.
● Use your phone to help others in emergencies.
● Call special non-emergency wireless number
when necessary.
Following Safety Guidelines
Note: Always turn off the phone in health care facilities and request
permission before using the phone near medical equipment.
To operate your phone safely and efficiently, always follow any
special regulations in a given area. Turn your phone off in areas
where use is forbidden or when it may cause interference or
danger.
Using Your Phone Near Other Electronic Devices
Most modern electronic equipment is shielded from radio
frequency (RF) signals. However, RF signals from wireless
phones may affect inadequately shielded
electronic equipment.
RF signals may affect improperly installed or inadequately
shielded electronic operating systems and/or entertainment
systems in motor vehicles. Check with the manufacturer or their
representative to determine if these systems are adequately
shielded from external RF signals. Also check with the
manufacturer regarding any equipment that has been added to
your vehicle.
Consult the manufacturer of any personal medical devices, such
as pacemakers and hearing aids, to determine if they are
adequately shielded from external RF signals.
Health and Safety Information
136
Turning Off Your Phone Before Flying
Turn off your phone before boarding any aircraft. To prevent
possible interference with aircraft systems, the U.S. Federal
Aviation Administration (FAA) regulations require you to have
permission from a crew member to use your phone while the
plane is on the ground. To prevent any risk of interference, FCC
regulations prohibit using your phone while the plane is in the air.
Turning Off Your Phone in Dangerous Areas
To avoid interfering with blasting operations, turn off your phone
when in a blasting area or in other areas with signs indicating
that two-way radios should be turned off. Construction crews
often use remote-control RF devices to set off explosives.
Note: Never transport or store flammable gas, liquid or explosives in the
compartment of your vehicle that contains your phone or accessories.
Turn off your phone when you’re in any area that has a potentially
explosive atmosphere. Although it’s rare, your phone or its
accessories could generate sparks. Sparks could cause an
explosion or a fire resulting in bodily injury or even death. These
areas are often, but not always, clearly marked. They include:
● Fueling areas such as gas stations.
● Below deck on boats.
● Fuel or chemical transfer or storage facilities.
● Areas where the air contains chemicals or particles such as
grain, dust or metal powders.
● Any other area where you would normally be advised to turn
off your vehicle’s engine.
Health and Safety Information
137
Restricting Children’s Access to your Phone
Your phone is not a toy. Children should not be allowed to play
with it because they could hurt themselves and others, damage
the phone or make calls that increase your
phone bill.
Caring for the Battery
The guidelines listed below help you get the most out of your
battery’s performance.
● Use only Samsung-approved batteries and desktop
chargers. These chargers are designed to maximize battery
life. Using other batteries or chargers voids your warranty
and may cause damage.
● In order to avoid damage, charge the battery only in
temperatures that range from 32º F to 104º F
(0º C to 40º C).
● Don’t use the battery charger in direct sunlight or in high
humidity areas, such as the bathroom.
● Never dispose of the battery by incineration.
● Keep the metal contacts on top of the battery clean.
● Don’t attempt to disassemble or short-circuit the battery.
● The battery may need recharging if it has not been used for a
long period of time.
● It’s best to replace the battery when it no longer provides
acceptable performance. It can be recharged hundreds of
times before it needs replacing.
Don’t store the battery in high temperature areas for long periods
of time. It’s best to follow these storage rules:
Less than one month:
Health and Safety Information
138
32
32º F to 104º F (0º C to 40º C)
Disposal of Lithium Ion (Li-Ion) Batteries
For safe disposal options of your Li-Ion batteries, contact your
nearest Samsung-authorized service center.
• For safety, do not handle a damaged or leaking
Li-Ion battery.
• Be sure to dispose of your battery properly. In some areas, the
disposal of batteries in household or business trash may be
prohibited.
Acknowledging Special Precautions and FCC
FCC Notice
The phone may cause TV or radio interference if used in close
proximity to receiving equipment. The FCC can require you to stop
using the phone if such interference cannot
be eliminated.
Vehicles using liquefied petroleum gas (such as propane or
butane) must comply with the National Fire Protection Standard
(NFPA-58). For a copy of this standard, contact the National Fire
Protection Association, One Batterymarch Park, Quincy, MA
02269, Attn: Publication Sales Division.
Cautions
Any changes or modifications to your phone not expressly
approved in this document could void your warranty for this
equipment, and void your authority to operate this equipment.
Only use approved batteries, antennas and chargers. The use of
any unauthorized accessories may be dangerous and void the
Health and Safety Information
139
phone warranty if said accessories cause damage or a defect to
the phone.
Although your phone is quite sturdy, it is a complex piece of
equipment and can be broken. Avoid dropping, hitting, bending
or sitting on it.
Body-Worn Operation
To maintain compliance with FCC RF exposure guidelines, if you
wear a handset on your body, use the Samsung supplied or
approved carrying case, holster or other body-worn accessory. If
you do not use a body-worn accessory, ensure that the antenna
is at least one inch (2.5 centimeters) from your body when
transmitting. Use of non- Samsung approved accessories may
violate FCC RF exposure guidelines.
For more information about RF exposure, please visit the FCC
website at www.fcc.gov.
SAR Values
● Head: 0.491 (W/kg)
● Body-worn: 0.38 (W/kg)
● Distance: 1.5 (cm)
FDA Consumer Update
Do wireless phones pose a health hazard?
The available scientific evidence does not show that any health
problems are associated with using wireless phones. There is no
proof, however, that wireless phones are absolutely safe.
Wireless phones emit low levels of radio frequency energy (RF) in
the microwave range while being used. They also emit very low
levels of RF when in stand-by mode. Whereas high levels of RF
Health and Safety Information
140
can produce health effects (by heating tissue), exposure to low
level RF that does not produce heating effects causes no known
adverse health effects. Many studies of low level RF exposures
have not found any biological effects. Some studies have
suggested that some biological effects may occur, but such
findings have not been confirmed by additional research. In some
cases, other researchers have had difficulty in reproducing those
studies, or in determining the reasons for inconsistent results.
What is FDA’s role concerning the safety of wireless phones?
Under the law, FDA does not review the safety of radiation-
emitting consumer products such as wireless phones before they
can be sold, as it does with new drugs or medical devices.
However, the agency has authority to take action if wireless
phones are shown to emit radio frequency energy (RF) at a level
that is hazardous to the user. In such a case, FDA could require
the manufacturers of wireless phones to notify users of the health
hazard and to repair, replace or recall the phones so that the
hazard no longer exists.
Although the existing scientific data do not justify FDA regulatory
actions, FDA has urged the wireless phone industry to take a
number of steps, including the following:
● Support needed research into possible biological effects of
RF of the type emitted by wireless phones;
● Design wireless phones in a way that minimizes any RF
exposure to the user that it is not necessary for device
function; and
● Cooperate in providing users of wireless phones with the
best possible information on possible effects of wireless
phone use on human health.
Health and Safety Information
141
FDA belongs to a interagency working group of the federal
agencies that have responsibility for different aspects of RF safety
to ensure coordinated efforts at the federal level. The following
agencies belong to this working group:
● National Institute for Occupational Safety and Health
● Environmental Protection Agency
● Federal Communications Committee
● Occupational Safety and Health Administration
The National Institutes of Health participates in some interagency
working group activities, as well.
FDA shares regulatory responsibilities about wireless phones with
the Federal Communications Commission (FCC). All phones that
are sold in the United States must comply with FCC safety
guidelines that limit RF exposure. FCC relies on FDA and other
health agencies for safety questions about wireless phones.
FCC also regulates the base stations that the wireless phone
networks rely upon. While these base stations operate at higher
power than do the wireless phones themselves, the wireless
exposures that people get from these base stations are typically
thousands of times lower than those they get from wireless
phones. Base stations are thus not the subject of the safety
questions discussed in this document.
What kinds of phones are the subject of this update?
The term “wireless phones” refers here to hand-held wireless
phones with built-in antennas, often called “cell,” “mobile,” or
“PCS”. These types of wireless phones can expose the user to
measurable radio frequency energy (RF) because of the short
distance between the phone and the user’s head. These RF
exposures are limited by Federal Communications Commission
safety guidelines that were developed with the advice of FDA and
Health and Safety Information
142
other federal health and safety agencies. When the phone is
located at greater distances from the user, the exposure to RF is
drastically lower because a person’s RF exposure decreases
rapidly with increasing distance from the source. The so-called
“cordless phones” which have a base unit connected to the
phone wiring in a house, typically operate at far lower per levels,
and thus produce RF exposures far below the FCC safety limits.
What are the results of the research done already?
The research done thus far has produced conflicting results, and
many studies have suffered from flaws in their research methods.
Animal experiments investigating the effects of radio frequency
energy (RF) exposures characteristic of wireless phones have
yielded conflicting results that often cannot be repeated in other
laboratories. A few animal studies, however, have suggested that
low levels of RF could Accelerate the development of cancer in
laboratory animals. However, many of the studies that showed
increased tumor development used animals that had been
genetically engineered or treated with cancer-causing chemicals
so as to be pre-disposed to develop cancer in absence of RF
exposure. Other studies exposed the animals to RF for up to 22
hours per day. These conditions are not similar to the conditions
under which people use wireless phones, so we don’t know with
certainty what results of such studies mean for human health.
Three large epidemiology studies have been published since
December 2000. Between them, the studies investigated any
possible association between the use of wireless phones and
primary brain cancer, glaucoma, meningioma, or acoustic
neuroma, tumors of the brain or salivary gland, leukemia, or
other cancers. None of the studies demonstrated the existence of
any harmful health effects from wireless phones RF exposures.
However, none of the studies can answer questions about long-
Health and Safety Information
143
term exposures, since average period of phone use in these
studies was around three years.
What research is needed to decide whether RF exposure from wireless
phones poses a health threat?
A combination of laboratory studies and epidemiological studies
of people actually using wireless phones would provide some of
the data that are needed. Lifetime animal exposure studies could
be completed in a few years. However, very large numbers of
animals would be needed to provide reliable proof of a cancer
promoting effect if one exists. Epidemiological studies can
provide data that is directly applicable to human populations, but
ten or more years’ follow-up may be needed to provide answers
about some health effects, such as cancer. This is because the
interval between the time of exposure to a cancer-causing agent
and the time tumors develop - if they do - may be many, many
years. The interpretation of epidemiological studies is hampered
by difficulties in measuring actual RF exposure during day-to-day
use of wireless phones. Many factors affect this measurement,
such as the angle at which the phone is held, or which model of
phone is used.
What is FDA doing to find out more about the possible health effects
of wireless phone RF?
FDA is working with the U.S. Toxicology Program and with groups
of investigators around the world to ensure that high priority
animal studies are conducted to address important questions
about the effects of exposure to radio frequency energy (RF).
FDA has been a leading participant in the World Health
Organization International Electromagnetic Fields (EMF) Project
since its inception in 1996. An influential result of tis work has
Health and Safety Information
144
been the development of a detailed agenda of research needs that
has driven the establishment of new research programs around
the world. The project has also helped develop a series of public
information documents on EMF issues.
FDA and the Cellular Telecommunications & Internet Association
(CTIA) have a formal Cooperative Research and Development
Agreement (CRADA) to do research on wireless phone safety. FDA
provides the scientific oversight, obtaining input from experts in
government, industry, and academic organizations. CTIA-funded
research is conducted through contracts to independent
investigators. The initial research will include both laboratory
studies and studies of wireless phone users. The CRADA will also
include a broad assessment of additional research needs in the
context of the latest research developments around the world.
How can I find out how much radio frequency energy exposure I can
get by using my wireless phone?
All phones sold in the United States must comply with Federal
Communications Commission (FCC) guidelines that limit radio
frequency energy (RF) exposures. FCC established these
guidelines in consultation with FDA and other federal health and
safety agencies. The FCC limit for exposure from wireless
telephones is set at a Specific Absorption Rate (SAR) of 1.6 watts
per kilogram (1.6 W/kg). The FCC limit is consistent with the
safety standards developed by the Institute of Electrical and
Electronic Engineering (IEEE) and the National Council on
Radiation Protection and Measurement. The exposure limit takes
into consideration the body’s ability to remove heat from the
tissue that absorb energy from the wireless phone and is set well
below levels known to have effects.
Health and Safety Information
145
Manufacturers of wireless phones must report the RF exposure
level for each model of phone to the FCC. The FCC website (http:/
/www.fcc.gov/oet/rfsafety) gives directions for locating the FCC
identification number on your phone so you can find your
phone’s RF exposure level in the online listing.
What has FDA done to measure the radio frequency energy coming
from wireless phones?
The Institute of Electrical and Electronic Engineers (IEEE) is
developing a technical standard for measuring the radio
frequency energy (RF) exposure from wireless phones and other
wireless hand sets with the participation and leadership of FDA
scientists and engineers. The standard, “Recommended Practice
for Determining the Spatial-Peak Specific Absorption Rate (SAR)
in the Human Body Due to Wireless Communications Devices:
Experimental Techniques,” sets forth the first consistent test
methodology for measuring the rate at which RF is deposited in
the heads of wireless phone users. The test method uses a tissue-
simulating model of the human head. Standardized SAR test
methodology is expected to greatly improve the consistency of
measurements made at different laboratories on the same phone.
SAR is the measurement of the amount of energy absorbed in
tissue, either by the whole body or a small part of the body. It is
measured in watts/kg (or milliwatts/g) of matter. This
measurement is used to determine whether a wireless phone
complies with safety guidelines.
What steps can I take to reduce my exposure to radio frequency
energy from my wireless phone?
If there is a risk from these products--and at this point we do not
know that there is--it is probably very small. But if you are
Health and Safety Information
146
concerned about avoiding even potential risks, you can take a
few simple steps to minimize your exposure to radio frequency
energy (RF). Since time is a key factor in how much exposure a
person receives, reducing the amount of time spent using a
wireless phone will reduce RF exposure.
If you must conduct extended conversations by wireless phone
every day, you could place more distance between your body and
the source of the RF, since the exposure level drops off
dramatically with distance. For example, you could use a headset
and carry the wireless phone away from your body or use a
wireless phone connected to a
remote antenna.
Again, the scientific data do not demonstrate that wireless phones
are harmful. But if you are concerned about RF exposure from
these products, you can use measures like those described
above to reduce your RF exposure from wireless phone use.
What about children using wireless phones?
The scientific evidence does not show a danger to users of
wireless phones, including children and teenagers. If you want to
take steps to lower exposure to radio frequency energy (RF), the
measured described above would apply to children and
teenagers using wireless phones. Reducing the time of wireless
phone use and increasing the distance between the user and the
RF source will reduce
RF exposure.
Some groups sponsored by other national governments have
advised that children be discouraged from using wireless phones
at all. For example, the government in the United Kingdom
distributed leaflets containing such a recommendation in
December 2000. They noted that no evidence exists that using a
Health and Safety Information
147
wireless phone causes brain tumors or other ill effects. Their
recommendation to limit wireless phone use by children was
strictly precautionary; it was not based on scientific evidence that
any health
hazard exists.
What about wireless phone
interference with medical equipment?
Radio frequency energy (RF) from wireless phones can interact
with some electronic devices. For this reason, FDA helped
develop a detailed test method to measure electromagnetic
interference (EMI) of implanted cardiac pacemakers and
defibrillators from wireless telephones. This test method is now
part of a standard sponsored by the Association for the
Advancement of Medical instrumentation (AAMI). The final draft, a
joint effort by FDA, medical device manufacturers, and many
other groups, was completed on late 2000. This standard will
allow manufacturers to ensure that cardiac pacemakers and
defibrillators are safe from wireless phone EMI.
FDA has tested hearing aids for interference from handheld
wireless phones and helped develop a voluntary standard
sponsored by the Institute of Electrical and Electronic Engineers
(IEEE). This standard specifies test methods and performance
requirements for hearing aids and wireless phones so that no
interference occurs when a person uses a “compatible” phone
and a “compatible” hearing aid at the same time. This standard
was approved by the IEEE in 2000.
FDA continues to monitor the use of wireless phones for possible
interactions with other medical devices. Should harmful
interference be found to occur, FDA will conduct testing to assess
Health and Safety Information
148
the interference and work to resolve
the problem.
Where can I find additional information?
● For additional information, please refer to the following
resources:
● FDA web page on wireless phones
(http://www.fda.gov/cdrh/phones/index.html)
● Federal Communications Commission FCC) RF
Safety Program
(http://www.fda.gov/oet/rfsafety)
● International Commission on Non-Ionizing
Radiation Protection
(http://www.icnirp.de)
● World Health Organization (WHO) International
EMF Project
(http://www.who.int/emf)
● National Radiological Protection Board (UK)
(http://www.nrpb.org.uk)
CTIA Safety Information
Exposure to radio frequency signals
Your wireless hand held portable telephone is a low power radio
transmitter and receiver. When it is ON, it receives and also sends
out radio frequency (RF) signals.
In August, 1996, the Federal Communications Commissions
(FCC) adopted RF exposure guidelines with safety levels for
hand-held wireless phones. Those guidelines are consistent with
Health and Safety Information
149
the safety standards previously set by both U.S. and international
standard bodies:
● ANSI C95.1 (1992)
● NCRP Report 86 (1986)
● ICNIRP (1996)
Those standards were based on comprehensive and periodic
evaluations of the relevant scientific literature. For example, over
120 scientists, engineers, and physicians from universities,
government health agencies, and industry reviewed the available
body of research to develop the ANSI Standard (C95.1).
The design of your phone complies with the FCC guidelines (and
those standards).
Antenna care
Use only the specified of approved replacement antenna.
Unauthorized antennas, modifications, or attachments could
damage the phone and may violate FCC regulations.
Phone operation
NORMAL POSITION: Hold the phone as you would any other
telephone with the antenna pointed up and over
your shoulder.
Tips on efficient operation:
For your phone to operate most efficiently:
● Extend your antenna fully.
● Do not touch the antenna unnecessarily when the phone is
in use. Contact with the antenna affects call quality and may
cause the phone to operate at a higher power level than
otherwise needed.
Health and Safety Information
150
Driving
Check the laws and regulations on the use of wireless telephones
in the areas where you drive. Always obey them. Also, if using
your phone while driving, please:
● Give full attention to driving--driving safety is your
first responsibility.
● Use hands-free operation, if available.
● Pull off the road and park before making or answering a call
if driving conditions so require.
Electronic devices
Most modern electronic equipment is shielded from RF signals.
However, certain electronic equipment may not be shielded
against RF signals from your wireless phone.
Pacemakers
The Health Industry Manufacturers Association recommends that
a minimum separation of six (6”) inches be maintained between
a hand-held wireless phone and a pacemaker to avoid potential
interference with the pacemaker. These recommendations are
consistent with the independent research by and
recommendations of Wireless Technology Research.
Persons with pacemakers:
● Should ALWAYS keep the phone more than six inches from
their pacemaker when the pacemaker is turned on;
● Should not carry the phone in a breast pocket;
● Should use the ear opposite the pacemaker to minimize the
potential for interference.
● If you have any reason to suspect that interference is taking
place, turn your phone OFF immediately.
Health and Safety Information
151
Hearing aids
Some digital wireless phones may interfere with some hearing
aids. In the event of such interference, you may want to consult
your service provider (or call the customer service line to discuss
alternatives.) Optional for each
phone manufacturer.
Other medical devices
If you use any other personal medical device, consult the
manufacturer of your device to determine if they are adequately
shielded from external RF energy. Your physician may be able to
assist you in obtaining this information.
Turn your phone OFF in health care facilities when any
regulations posted in these areas instruct you to do so. Hospitals
or health care facilities may be using equipment that could be
sensitive to external RF energy.
Vehicles
RF signals may affect improperly installed or inadequately
shielded electronic systems in motor vehicles. Check with the
manufacturer or its representative regarding your vehicle. You
should also consult the manufacturer of any equipment that has
been added to your vehicle.
Posted facilities
Turn your phone OFF in any facility where posted notices
so require.
Aircraft
FCC regulations prohibit using your phone while in the air. Switch
OFF your phone before boarding an aircraft.
Health and Safety Information
152
Blasting areas
To avoid interfering with blasting operations, turn your phone OFF
when in a “blasting area” or in areas posted: “Turn off two-way
radio”. Obey all signs and instructions.
Potentially explosive atmospheres
Turn your phone OFF when in any area with a potentially
explosive atmosphere and obey all signs and instructions. Sparks
in such areas could cause an explosion or fire resulting in bodily
injury of even death.
Areas with a potentially explosive atmosphere are often but not
always clearly marked. They include fueling areas such as
gasoline stations; below deck on boats; fuel or chemical transfer
or storage facilities; vehicles using liguefied petroleum gas (such
as propane or butane); areas where the air contains chemicals or
particles, such as grain, dust, or metal powders; and any other
area where you would normally be advised to turn off your
vehicle engine.
For vehicles equipped with an airbag
An airbag inflates with great force. DO NOT place objects,
including both installed or portable wireless equipment, in the
area over the air bag deployment area. If in-vehicle wireless
equipment is improperly installed and the air bag inflates, serious
injury could result.
Owner's Record
The model number, regulatory number and serial number are
located on a nameplate inside the battery compartment. Record
the serial number in the space provided below. This will be
helpful if you need to contact us about your phone in the future.
Health and Safety Information
153
STANDARD LIMITED WARRANTY
What is Covered and For How Long? SAMSUNG
TELECOMMUNICATIONS AMERICA, L.P. (SAMSUNG) warrants to
the original purchaser ("Purchaser") that SAMSUNG’s Phones
and accessories ("Products") are free from defects in material
and workmanship under normal use and service for the period
commencing upon the date of purchase and continuing for the
following specified period of time after that date:
Phone 1 Year
Batteries 1 Year
Leather Case/Pouch 90 Days
Holster90 Days
Other Phone Accessories 1 Year
What is Not Covered? This Limited Warranty is conditioned
upon proper use of Product by Purchaser. This Limited Warranty
does not cover: (a) defects or damage resulting from accident,
misuse, abuse, neglect, unusual physical, electrical or
electromechanical stress, or modification of any part of Product,
including antenna, or cosmetic damage; (b) equipment that has
the serial number removed or made illegible; (c) any plastic
surfaces or other externally exposed parts that are scratched or
damaged due to normal use; (d) malfunctions resulting from the
use of Product in conjunction with accessories, products, or
ancillary/peripheral equipment not furnished or approved by
SAMSUNG; (e) defects or damage from improper testing,
operation, maintenance, installation, or adjustment; (f)
installation, maintenance, and service of Product, or (g) Product
used or purchased outside the United States or Canada. This
STANDARD LIMITED WARRANTY
155
Limited Warranty covers batteries only if battery capacity falls
below 80% of rated capacity or the battery leaks, and this Limited
Warranty does not cover any battery if (i) the battery has been
charged by a battery charger not specified or approved by
SAMSUNG for charging the battery, (ii) any of the seals on the
battery are broken or show evidence of tampering, or (iii) the
battery has been used in equipment other than the SAMSUNG
phone for which it is specified.
What are SAMSUNG’s Obligations? During the applicable
warranty period, SAMSUNG will repair or replace, at SAMSUNG’s
sole option, without charge to Purchaser, any defective
component part of Product. To obtain service under this Limited
Warranty, Purchaser must return Product to an authorized phone
service facility in an adequate container for shipping,
accompanied by Purchaser’s sales receipt or comparable
substitute proof of sale showing the date of purchase, the serial
number of Product and the sellers’ name and address. To obtain
assistance on where to deliver the Product, call Samsung
Customer Care at 1-888-987-4357. Upon receipt, SAMSUNG
will promptly repair or replace the defective Product. SAMSUNG
may, at SAMSUNG’s sole option, use rebuilt, reconditioned, or
new parts or components when repairing any Product or replace
Product with a rebuilt, reconditioned or new Product. Repaired/
replaced leather cases, pouches and holsters will be warranted
for a period of ninety (90) days. All other repaired/replaced
Product will be warranted for a period equal to the remainder of
the original Limited Warranty on the original Product or for 90
days, whichever is longer. All replaced parts, components,
boards and equipment shall become the property of SAMSUNG. If
SAMSUNG determines that any Product is not covered by this
STANDARD LIMITED WARRANTY
156
Limited Warranty, Purchaser must pay all parts, shipping, and
labor charges for the repair or return of such Product.
What Are the Limits On SAMSUNG’s Liability? EXCEPT AS
SET FORTH IN THE EXPRESS WARRANTY CONTAINED HEREIN,
PURCHASER TAKES THE PRODUCT “AS IS,” AND SAMSUNG
MAKES NO WARRANTY OR REPRESENTATION AND THERE ARE
NO CONDITIONS, EXPRESS OR IMPLIED, STATUTORY OR
OTHERWISE, OF ANY KIND WHATSOEVER WITH RESPECT TO THE
PRODUCT, INCLUDING BUT NOT LIMITED TO:
•THE MERCHANTABILITY OF THE PRODUCT OR ITS FITNESS FOR
ANY PARTICULAR PURPOSE OR USE;
•WARRANTIES OF TITLE OR NON-INFRINGEMENT;
•DESIGN, CONDITION, QUALITY, OR PERFORMANCE OF THE
PRODUCT;
•THE WORKMANSHIP OF THE PRODUCT OR THE COMPONENTS
CONTAINED THEREIN; OR
•COMPLIANCE OF THE PRODUCT WITH THE REQUIREMENTS OF
ANY LAW, RULE, SPECIFICATION OR CONTRACT PERTAINING
THERETO.
NOTHING CONTAINED IN THE INSTRUCTION MANUAL SHALL BE
CONSTRUED TO CREATE AN EXPRESS WARRANTY OF ANY KIND
WHATSOEVER WITH RESPECT TO THE PRODUCT. ALL IMPLIED
WARRANTIES AND CONDITIONS THAT MAY ARISE BY OPERATION
OF LAW, INCLUDING IF APPLICABLE THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE HEREBY LIMITED TO THE SAME DURATION OF
TIME AS THE EXPRESS WRITTEN WARRANTY STATED HEREIN.
SOME STATES/PROVINCES DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU. IN ADDITION, SAMSUNG
STANDARD LIMITED WARRANTY
157
SHALL NOT BE LIABLE FOR ANY DAMAGES OF ANY KIND
RESULTING FROM THE PURCHASE, USE, OR MISUSE OF, OR
INABILITY TO USE THE PRODUCT OR ARISING DIRECTLY OR
INDIRECTLY FROM THE USE OR LOSS OF USE OF THE PRODUCT
OR FROM THE BREACH OF THE EXPRESS WARRANTY,
INCLUDING INCIDENTAL, SPECIAL, CONSEQUENTIAL OR SIMILAR
DAMAGES, OR LOSS OF ANTICIPATED PROFITS OR BENEFITS, OR
FOR DAMAGES ARISING FROM ANY TORT (INCLUDING
NEGLIGENCE OR GROSS NEGLIGENCE) OR FAULT COMMITTED
BY SAMSUNG, ITS AGENTS OR EMPLOYEES, OR FOR ANY
BREACH OF CONTRACT OR FOR ANY CLAIM BROUGHT AGAINST
PURCHASER BY ANY OTHER PARTY. SOME STATES/PROVINCES
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU
MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO
STATE/PROVINCE TO PROVINCE. THIS LIMITED WARRANTY
SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL
PURCHASER OF THIS PRODUCT AND STATES PURCHASER’S
EXCLUSIVE REMEDY. IF ANY PORTION OF THIS LIMITED
WARRANTY IS HELD ILLEGAL OR UNENFORCEABLE BY REASON
OF ANY LAW, SUCH PARTIAL ILLEGALITY OR UNENFORCEABILITY
SHALL NOT AFFECT THE ENFORCEABILITY FOR THE REMAINDER
OF THIS LIMITED WARRANTY WHICH PURCHASER
ACKNOWLEDGES IS AND WILL ALWAYS BE CONSTRUED TO BE
LIMITED BY ITS TERMS OR AS LIMITED AS THE LAW PERMITS.
THE PARTIES UNDERSTAND THAT THE PURCHASER MAY USE
THIRD-PARTY SOFTWARE OR EQUIPMENT IN CONJUNCTION
WITH THE PRODUCT. SAMSUNG MAKES NO WARRANTIES OR
REPRESENTATIONS AND THERE ARE NO CONDITIONS, EXPRESS
OR IMPLIED, STATUTORY OR OTHERWISE, AS TO THE QUALITY,
STANDARD LIMITED WARRANTY
158
CAPABILITIES, OPERATIONS, PERFORMANCE OR SUITABILITY OF
ANY THIRD-PARTY SOFTWARE OR EQUIPMENT, WHETHER SUCH
THIRD-PARTY SOFTWARE OR EQUIPMENT IS INCLUDED WITH
THE PRODUCT DISTRIBUTED BY SAMSUNG OR OTHERWISE,
INCLUDING THE ABILITY TO INTEGRATE ANY SUCH SOFTWARE
OR EQUIPMENT WITH THE PRODUCT. THE QUALITY,
CAPABILITIES, OPERATIONS, PERFORMANCE AND SUITABILITY OF
ANY SUCH THIRD-PARTY SOFTWARE OR EQUIPMENT LIE SOLELY
WITH THE PURCHASER AND THE DIRECT VENDOR, OWNER OR
SUPPLIER OF SUCH THIRD-PARTY SOFTWARE OR EQUIPMENT,
AS THE CASE MAY BE.
This Limited Warranty allocates risk of Product failure between
Purchaser and SAMSUNG, and SAMSUNG’s Product pricing
reflects this allocation of risk and the limitations of liability
contained in this Limited Warranty. The agents, employees,
distributors, and dealers of SAMSUNG are not authorized to make
modifications to this Limited Warranty, or make additional
warranties binding on SAMSUNG. Accordingly, additional
statements such as dealer advertising or presentation, whether
oral or written, do not constitute warranties by SAMSUNG and
should not be relied upon.
Samsung Telecommunications America, L.P.
1130 East Arapaho Road
Richardson, Texas 75081
Phone: 1-800-SAMSUNG
Phone: 1-888-987-HELP (4357)
©2003 Samsung Telecommunications America. All rights
reserved.
STANDARD LIMITED WARRANTY
159
No reproduction in whole or in part allowed without prior written
approval.
Specifications and availability subject to change without notice.
[080802]
STANDARD LIMITED WARRANTY
160
Glossary
To help you understand the main technical terms and
abbreviations used in this booklet and take full advantage of the
features on your mobile phone, here are a few definitions.
Call Forwarding
Ability to reroute calls to another number.
Call Holding
Ability to put one call on standby while answering or making
another call; you can then switch between the two calls, as
required.
Call Waiting
Ability to inform users that they have an incoming call when
engaged on another call.
GPRS (General Packet Radio Service)
New non-voice value-added service that allows information to be
sent and received across a mobile telephone network. GPRS
provides continuous connection to the Internet for mobile phone
and computer users. It is based on the Global System for Mobile
Communication (GSM) circuit-switched cellular phone
connections and the Short Message Service (SMS).
GSM (Global System for Mobile Communication)
International standard for cellular communication, guaranteeing
compatibility between the various network operators. GSM covers
most European countries and many other parts of the world.
Java
Glossary
161
Programming language generating applications that can run on
all hardware platforms, whether small, medium or large, without
modification. It has been promoted for and geared heavily to the
Web, both for public Web sites and Intranets. When a Java
program runs from a Web page, it is called a Java applet. When
it is run on a mobile phone or pager, it is called a MIDlet.
Line Identification Services (Caller ID)
Services allowing subscribers to view or block the telephone
numbers of callers.
Multiparty Calling
Ability to establish a conference call involving up to five additional
parties.
Phone Password
Security code used to unlock the phone when you have selected
the option to lock it automatically each time it switches on.
PIN (Personal Identification Number)
Security code that protects the phone against unauthorized use.
The PIN is supplied by the service provider with the SIM card. It
may be a four to eight-digit number and can be changed, as
required.
PUK (PIN Unblocking Key)
Security code used to unlock the phone when an incorrect PIN
has been entered three times in succession. The eight-digit
number is supplied by the service provider with the SIM card.
Roaming
Glossary
162
Use of your phone when you are outside your home area (when
travelling for example).
SDN (Service Dialing Numbers)
Telephone numbers supplied by your network provider and giving
access to special services, such as voice mail, directory
inquiries, customer support and emergency services.
SIM (Subscriber Identification Module)
Card containing a chip with all the information required to operate
the phone (network and memory information, as well as the
subscriber’s personal data). The SIM card fits into a small slot on
the back of the phone and is protected by the battery.
SMS (Short Message Service)
Network service sending and receiving messages to and from
another subscriber without having to speak to the correspondent.
The message created or received can be displayed, received,
edited or sent.
Soft Keys
Two keys marked
which:
and
on the phone, the purpose of
♦Varies according to the function that you are
currently using
♦Is indicated on the bottom line of the display just
above the corresponding key
Dual Band
Ability to handle any of the following types of network: GSM 900
and GSM 1900 MHz bands, for greater call success and wider
roaming.
Voice Mail
Glossary
163
Computerized answering service that automatically answers your
calls when you are not available, plays a greeting (optionally in
your own voice) and records a message.
Glossary
164
Card
Changing
PIN (4.6.2) •,
Characters
Colour Theme •,
Connect
Copying
D
Deleting
Index
166
Display
icons •,
E
Editing
F
Functions
G
Groups
H
I
Icons
Index
167
K
Key tones
Keys
location •,
L
Last number, redial •,
Letters
Light
Locking
SIM card (4.6.5) •,
Lower-case characters
M
Memory Status
Memos
copying •,
editing •,
Menus
Index
168
Messages
templates (1.3) •,
writing (1.2) •,
Multiparty calls
Muting
N
Names
Numbers
O
Options
selecting •,
Index
169
P
Password
phone
Phone
Phonebook
editing •,
PIN
PIN2
PUK •,
R
Redialling
Ring
Index
170
S
Safety
quick guide •,
Sending
key tones •,
Setting
alarm (5.4) •,
SIM card
SMS
Solving problems •,
Switching on/off
T
Tasks
Index
171
Text
Time
format (5.3.4) •,
Tone
U
Unpacking •,
Upper-case characters
V
Volume
W
Waiting
Index
172
|
