Ultra Products 96500 User Manual

UltraATA 133 PCI  
Quick Installation Guide  
Introducing the UltraATA 133 PCI  
The UltraATA133PCIis an ultra high-speed dualchannel  
Ultra ATA/ 133 controller board for use in Pentium-class  
computer.  
Features and Benefits  
Compliant with UltraDMA6ATA/ 133specifications  
Compliant with PCI v2.2 Plug-n-Play  
Provides two independent Ultra ATA channels  
(built-in 256-byte FIFOs per channel)  
Full ACPI power management support  
Supports Ultra DMA 0-6 and Multi-word DMA 0-2  
Breaks the 137GB barrier! Supports hard drives  
larger than 137GB  
Coexists with on-board controller  
CRC (Cyclical Redundancy Check) error-checking  
provides data verification and achieves flawless  
data tranfer  
Flash BIOS for easy upgrade  
Achieves burst data transfer rates up to 133MB/ sec  
Works with various brand,capacity hard disk drives  
and ATAPI devices  
System Requirements  
Pentium-class computer with an available PCI slot  
Windows 98SE/ ME/ NT 4.0/ 2000/ XP/ Server 2003  
1
04-0233D  
1. Turn OFF the power to your computer and any  
other connected peripheral devices.  
2. Unplug the power cord from the back of the  
computer.  
3. Remove your computers cover.  
4. Remove the slot bracket from an available PCI slot.  
5. To install the card, carefully align the card's bus  
connector w ith the selected PCI slot on the  
motherboard. Push the board down firmly, but  
gently, until it is well seated.  
6. Replace the slot bracket's holding screw to secure  
the card.  
Device Connection  
The UltraATA 133 PCI is a dual channel Ultra ATA/ 133  
controller that supports up to four IDE hard disk drives  
or ATAPI devices. If you plan to use the second IDE  
channel (IDE2).  
In order to achieve high-speed data transfer, a 40-pin/ 80-  
wire Ultra ATA ribbon cable is recommended. Also, do  
not mix Ultra ATA/ 133 hard disk with slower IDE or  
ATAPI devices on the same channel.  
1. Install hard disk drive(s) in chassis.  
2. Attach one connector on the long end of the Ultra  
ATA ribbon cable to the board's IDE connector and  
the other connector(s) to your IDE drive(s). Make  
sure pin 1 on the cable (indicated by the colored  
stripe) matches pin 1 on the board's IDE connector  
and your IDE drive(s).  
3. When two drives are installed on the same IDE  
channel, make sure one drive is set up as Master and  
the other as Slave. This rule applies to both IDE  
channels.  
3
4. The Ultra ATA ribbon cable has two connectors. If  
you install only one drive, connect it to the end  
connector of the cable. On the other hand, if you  
install two drives, connect the master drive to the  
end connector of the cable and the slave drive in the  
middle connector.  
Figure 2. Connecting the cable  
5. Reconnect the system power and other peripherals  
to your computer.  
Driver Installation  
This section provides information on how to install the  
UltraATA 133 PCI drivers for the following operating  
systems:  
Windows 98SE........................................................... page 5  
Windows ME ............................................................. page 6  
Verify Windows 98SE/ ME Installation ..............page 6-7  
Windows NT 4.0 ....................................................... page 7  
Verify Windows NT 4.0 Installation ...................... page 8  
Windows 2000 ........................................................... page 8  
Windows XP/ Server 2003 ....................................... page 9  
Verify Windows 2000/ XP/ 2003 Installation ...... page 10  
Bios Configuration .................................................. page 10  
4
Windows 98SE  
For New Windows 98SE Installation  
1. Install the board and follow Microsoft procedures to  
install Windows 98SE accordingly.  
2. Once Windows has been installed, right click My  
Computer and click Properties. Select Device  
Manager tab.  
3. Double click PCI Mass Storage Controller listed  
under Other Devices.  
4. Select Driver tab, then click Update Driver button.  
5. Insert the driver diskette and click Next.  
6. Select Search for a better driver ... and click Next.  
7. Check Floppy disk drives, uncheck the other boxes,  
then click Next. Click Next again, then Finish.  
8. Remove the driver diskette and restart Windows to  
complete driver installation.  
For Existing Windows 98SE Installation  
1. Install the board and boot up Windows 98SE.  
2. At the Add New Hardware Wizard, click Next.  
3. Select Search for the best driver for your device and  
click Next.  
4. Insert the driver diskette, check Floppy disk drives,  
uncheck the other boxes, then click Next.  
5. Click Next, then Finish.  
6. Remove the driver diskette and restart Windows to  
complete driver installation.  
5
Windows ME  
For New Windows ME Installation  
1. Installthe board and follow Microsoft procedures to  
install Windows ME accordingly.  
2. Once Windows has been installed, right click My  
Computer, then click Properties. Select Device  
Manager tab.  
3. Double click PCI Mass Storage Controller listed  
under Other Devices.  
4. Select Driver tab, then click Update Driver button.  
5. Insert the driver diskette, select Automatic search  
for a better driver (Recommended),then click Next.  
6. Click Finish, remove the driver diskette and click  
Yes to restart Wind ow s to com p lete d river  
installation.  
For Existing Windows ME Installation  
1. Install the board and boot up Windows ME.  
2. At the Add New Hardware Wizard,insert the driver  
diskette.  
3. Select Au tom atic search for a b etter d river  
(Recommended), then click Next.  
4. Click Finish.  
5. Remove the driver diskette and restart Windows to  
complete driver installation.  
To Verify Windows 98SE/ME Installation  
1. Right-click My Computer, then click Properties.  
Select Device Manager tab.  
2. Double click SCSI Controllers, an entry, Silicon  
Image SiI 0680ATA/133Controller should be listed.  
6
3. H ighlight Silicon Im age SiI 0680 ATA/133  
Controller and click Properties. A message This  
device is working properly is displayed in the dialog  
box, the driver has been correctly installed. If any  
error message is displayed, remove Silicon Image  
SiI 0680ATA/133Controller and restartyour system.  
Windows NT 4.0  
For New Windows NT 4.0 Installation  
1. Installthe board and follow Microsoft procedures to  
install Windows NT 4.0 accordingly.  
2. At the Windows NT Setup screen, press F6 to  
specify and add the driver.  
3. Press S, select Other, then press Enter.  
4. Insert the driver diskette and press Enter.  
5. Select Silicon Image SiI 0680 ATA/133 Controller  
and press Enter.  
6. Press Enter to continue and follow on-screen  
instru ctions to com p lete Wind ow s N T 4.0  
installation.  
For Existing Windows NT 4.0 Installation  
1. Install the board and boot up Windows NT 4.0.  
2. Double click My Computer/ Control Panel/SCSI  
Adapters, then click the Drivers tab.  
3. Click Add… then Have Disk....  
4. Insert the driver diskette, type in A:, then click OK.  
5. H ighlight Silicon Im age SiI 0680 ATA/133  
Controller and click OK.  
6. Click OK, remove the driver diskette and restart NT  
to complete driver installation.  
7
To Verify Windows NT 4.0 Installation  
1. Double click My Computer/Control Panel/SCSI  
Adapters.  
2. H ighlight Silicon Im age SiI 0680 ATA/133  
Controller from SCSI Adapters listing and click  
Properties. A message This device is working properly  
is displayed in the dialog box, the driver has been  
correctly installed.  
Windows 2000  
For New Windows 2000 Installation  
1. Installthe board and follow Microsoft procedures to  
install Windows 2000 accordingly.  
2. Restart your system w hen prompted d uring  
Windows' installation.  
3. At the Windows 2000 Setup screen, press F6 to  
install the driver.  
4. Insert the driver diskette. Press S, then press Enter.  
5. Select Silicon Image SiI 0680 ATA/133 Controller  
and press Enter.  
6. Press Enter to continue and follow on-screen  
instructions to complete installation.  
For Existing Windows 2000 Installation  
1. Install the board and boot up Windows 2000.  
2. At the Found New Hardware Wizard, click Next.  
3. Select Search for a suitable driver for my device  
(recommended) and click Next.  
4. Insert the driver diskette, check Floppy disk drives,  
uncheck the other boxes, and click Next. Click Next  
again to continue.  
5. Click Finish, remove the driver diskette and restart  
Windows to complete driver installation.  
8
Windows XP/Server 2003  
For New Windows XP/Server 2003 Installation  
1. Installthe board and follow Microsoft procedures to  
install Windows XP accordingly.  
2. Restart your system w hen prompted d uring  
Windows' installation.  
3. At the Windows Setup screen, press F6 to install the  
driver.  
4. Insert the driver diskette. Press S then press Enter.  
5. Select Silicon Image SiI 0680 ATA/133 Controller  
and press Enter.  
6. Press Enter to continue and follow on-screen  
instructions to complete Windows XP installation.  
7. When the Software Installation warning pops up,  
click Yes. And when the Hardware Installation  
warning pops up, click Yes again.  
For Existing Windows XP/Server 2003 Installation  
1. Install the board and boot up Windows XP.  
2. At the Found New Hardware Wizard, insert the  
d river d iskette, select In stall th e softw are  
automatically (Recommended), then click Next.  
3. Click Finish, remove the driver diskette and restart  
Windows to complete the installation.  
9
To Verify Windows 2000/XP/2003 Installation  
1. Right click My Computer and click Manage.  
2.  
Select Device Manager.  
3. Double click SCSI and RAID Controllers, then  
double click Silicon Image SiI 0680 ATA/133  
Controller to display driver properties.  
4. A message Thisdeviceisworkingproperlyis displayed  
in the dialog box, the driver has been correctly  
installed.  
Bios Configuration  
The UltraATA 133 PCI BIOS will appear everytime your  
system starts up. If the bios doesn't show, please try your  
controller in another PCI slot. During this (Post) process,  
the bios will show up and indicate the devices attached to  
it.  
10  
Technical Support and Warranty  
Q UESTIO N S?  
SIIG’s O n lin e Su p p ort has answ ers!  
Simply visit our website at www.siig.com and click on Support.  
Our online support database is updated daily with new drivers  
and solutions. Answers to your questions could be just a few clicks  
away. You can also submit questions online and one ofour technical  
support analysts will promptly respond.  
A lifetime manufacturer warranty supplied with this product is  
offered by SIIG, Inc. Please see SIIG website for more warranty  
details. If you should happen to encounter any problems with this  
product, please follow the procedures below.  
If it is within the store's return policy period, please return the  
product to the store where you purchased from.  
If your purchase has passed the store's return policy period, please  
follow these steps to have the product repaired or replaced.  
Step 1: Submit your RMA request.  
Go to www.siig.com, click Support, then RMA to submit a  
request to SIIG RMA. If the product is determined to be  
defective,an RMA number willbe issued. SIIG RMA department  
can also be reached at (510)413-5333.  
Step 2: After obtaining an RMA number, ship the product.  
Properly pack the product for shipping. All software, cable(s)  
and any other accessories that came with the original package  
must be included.  
Clearly write your RMA number on the top of the returned  
package. SIIG will refuse to accept any shipping package, and  
will not be responsible for a product returned without an  
RMA number posted on the outside of the shipping carton.  
You are responsible for the cost of shipping the product to  
SIIG at the following address:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538  
RMA #:  
SIIG will ship the repaired or replaced product via Ground  
in the U.S and International Economy outside of the U.S at  
no cost to the customer.  
11  
About SIIG, Inc.  
Founded in 1985, SIIG, Inc. is a leading computer upgrade  
manufacturer of I/ O connectivity products, including PCI & ISA  
serial and parallel ports, USB, Serial ATA & UltraATA controllers,  
FireWire (1394a/ b),Networking,Sound Cards,and other accessories.  
SIIG is the premier one-stop source of upgrades.  
SIIG products offer comprehensive user manuals,many user-friendly  
features, and are backed by an extensive manufacturer warranty.  
High-quality control standards are evident by the overall ease of  
installation and compatibility of our products, as well as one of the  
lowest defective return rates in the industry. SIIG products can be  
found in computer retailstores,mailorder catalogs,and e-commerce  
sitesin theAmericasand theUK,aswellasthrough major distributors,  
system integrators, and VARs.  
PRODUCT NAME  
UltraATA 133 PCI  
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B  
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE  
FCC COMPLIANCE STATEMENT:  
This device complies with part 15 of the FCC Rules. Operation is subject  
to the following two conditions: (1) This device may not cause harmful  
interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation.  
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE  
SIIG, Inc.  
6078 Stewart Ave.  
Fremont, CA 94538-3152  
UltraATA 133 PCI is a trademark of SIIG, Inc.  
SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are  
registered trademarks of Microsoft Corporation. Pentium is a registered trademark of Intel  
Corporation. Other names used in publication are for identification only and may be trademarks  
of their respective companies.  
March, 2005  
Copyright ©2005 by SIIG, Inc. All rights reserved.  

StarTechcom SAT2510BU2B User Manual
Sony D 182CKAN User Manual
Seagate ST240FP0001 User Manual
Seagate MEDALIST 1080SL User Manual
Rotel RCD 975 User Manual
Pioneer DEH 9 User Manual
Philips Xenium CTX800BRN User Manual
Philips E GSM 1800 User Manual
Philips Audio CD Recorder CDR770 User Manual
Oregon Scientific RRM612PU User Manual