Sprint Nextel Cell Phone NNTN7985A_040810 User Manual

User Guide  
MOTOROLA  
www.nextel.com  
©2010 Sprint. SPRINT and the NEXTEL name and logo are trademarks  
of Sprint. Other marks are the property of their respective owners.  
4/8/10  
FCC Notice to Users  
DECLARATION OF CONFORMITY  
The following statement applies to all products that have  
received FCC approval. Applicable products bear the FCC  
logo, and/or an FCC ID in the format FCC-ID: IHDT56KQ1 on  
the product label.  
Per FCC CFR 47 Part 2 Section 2.1077(a)  
Motorola has not approved any changes or modifications to  
this device by the user. Any changes or modifications could  
void the user’s authority to operate the equipment. See 47 CFR  
Sec. 15.21.  
Class B Digital Device  
Responsible Party Name: Motorola, Inc.  
As a personal computer peripheral, this device complies with  
part 15 of the FCC Rules. Operation is subject to the following  
two conditions: (1) This device may not cause harmful  
interference, and (2) this device must accept any interference  
received, including interference that may cause undesired  
operation. See 47 CFR Sec. 15.19(3).  
Address: 8000 West Sunrise Boulevard  
Plantation, FL 33322 USA  
Phone Number: 1 (800) 453-0920  
Hereby declares that the product:  
Product Name: MOTOROLA i1  
Model Number: H76XAN9JR9AN  
FCC ID: IHDP56KV1  
Conforms to the following regulations:  
FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section  
15.109(a)  
Note: This equipment has been tested and found to comply  
with the limits for a Class B digital device, pursuant to  
part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful  
interference in a residential installation. This equipment  
generates, uses and can radiate radio frequency  
energy and, if not installed and used in accordance  
with the instructions, may cause harmful interference to  
radio communications. However, there is no guarantee  
that interference will not occur in a particular installation.  
If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the  
equipment off and on, the user is encouraged to try to correct  
the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and  
receiver.  
Connect the equipment into an outlet on a circuit  
different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV  
technician for help.  
Table of Contents  
Microsoft™ Office Outlook™ Synchronization . 65  
Wi-Fi® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66  
12. Bluetooth® Wireless . . . . . . . . . . . . . . . . 105  
Introduction  
Note: Because of updates in phone software, this printed  
guide may not be the most current version for your  
phone. Visit www.nextel.com and sign in to access the  
most recent version of the user guide.  
This User Guide introduces you to your wireless service  
and all the features of your new phone.  
WARNING: Please refer to the Important Safety Information  
section on page 114 to learn about information  
that will help you safely use your phone. Failure to  
read and follow the Important Safety Information  
in this phone guide may result in serious bodily  
injury, death, or property damage.  
Throughout this guide, you’ll find tips that highlight  
special shortcuts and timely reminders to help you  
make the most of your new phone and service. The  
Table of Contents and Index will also help you quickly  
locate specific information.  
You’ll get the most out of your phone if you read each  
section. However, if you’d like to get right to a specific  
feature, simply locate that section in the Table of  
Contents and go directly to that page. Follow the  
instructions in that section, and you’ll be ready to use  
your phone in no time.  
i
 
Use and Care  
Use  
&
Care  
Your mobile device is designed to resist damage from  
exposure to certain rugged conditions. However, avoid  
prolonged or extreme exposure to those conditions. To  
help protect your mobile device, always make sure the  
battery compartment and any connector covers are  
closed and secure, and observe the following  
precautions:  
extreme heat or cold  
Avoid temperatures below 0°C/32°F or  
above 45°C/113°F.  
shock and vibration  
Avoid dropping your mobile device.  
liquids  
Don’t expose your mobile device to water,  
extreme humidity, sweat, or other liquids. If it  
does get wet, don’t try to accelerate drying  
with the use of an oven or dryer, as this may  
damage the mobile device.  
dirt  
Don’t expose your mobile device to dirt, sand,  
food, or other inappropriate materials.  
microwaves  
Don’t try to dry your mobile device in a  
microwave oven.  
cleaning solutions  
To clean your mobile device, use only a dry  
soft cloth. Don’t use alcohol or other cleaning  
solutions.  
ii  
 
Setting Up Your Phone  
1. Setting Up Service  
1. Make sure your SIM card is in place.  
2. Install the battery.  
See “Installing the Battery” on page 6.  
3. Press and hold End/Power " for two seconds to  
turn the phone on.  
If your phone is activated, it will turn on, search for  
service, and display the home screen.  
If your phone's SIM PIN is set, you may be  
prompted to enter your SIM PIN code when you  
turn on your phone. Press Menu /, enter the  
four-digit SIM code, and touch OK to allow phone  
transmissions as prompted. (See “SIM Card  
Your Phone’s Navigation Pad  
Back Key  
Home  
Key  
Speaker Key  
Menu  
Key  
If your phone is not yet activated, see “Activating  
End/Power  
Key  
Talk Key  
Navigation Key  
OK  
OK Key  
1
   
4. Follow the onscreen instructions to complete the  
MOTOROLA i1 setup wizard.  
Getting Started With Your Phone  
Your SIM Card  
5. Make your first call.  
Locating the SIM Card  
From the home screen, touch  
display the keypad, and then enter a phone  
number.  
Dialer to  
Your SIM (Subscriber Identity Module) card is a small  
card inserted into the SIM card holder within your  
phone below the battery.  
Press Talk `.  
Tip: If your phone screen is locked, drag the onscreen  
Stretch to unlock button to the right to display the home  
screen.  
If no SIM card came with your phone, contact Nextel  
Customer Service at 1-800-639-6111.  
Most users will never need to remove or insert the SIM  
card. However, if it becomes necessary, follow the  
instructions in “Removing and Inserting the SIM Card”  
on page 3.  
Note: Your phone’s battery should have enough charge for  
your phone to turn on and find a signal, set up your  
voicemail, and make a call. You should fully charge  
your battery as soon as possible. See “Charging the  
Battery” on page 7 for details.  
2
   
Removing and Inserting the SIM Card  
Important: The SIM card is designed for optimal Contacts  
storage and feature use. For Nextel SIM card  
compatibility information, visit  
Important: To avoid losing information stored in your SIM  
card, do not remove it from your phone unless  
absolutely necessary.  
In some cases, Contacts and Groups may not be  
accessible if you move your SIM card to another  
phone. Contacts and Groups created with your  
MOTOROLA i1 may not be readable by an older  
iDEN SIM-based phone.  
To remove your SIM card:  
1. With your phone powered off, slide the battery  
door latch on the side of the phone down. While  
holding the latch down, lift and remove the battery  
door.  
Note: Your MOTOROLA i1 Contacts are managed and stored  
on your phone rather than on the SIM card. If you are  
using a SIM card from a previous phone, you can  
import your existing contacts from the SIM card to your  
MOTOROLA i1 using the SIM Manager. Likewise, you  
can export your phone’s Contacts to your SIM card.  
details.  
3
 
2. Remove the battery, and then use your thumbs to  
carefully slide the SIM card out from under the  
edge.  
Important: Do not touch the gold-colored areas of your SIM  
card.  
Note: Protect your SIM card as you would any delicate object.  
Memory Card  
Store it carefully.  
A microSD memory card is provided with your phone.  
The provided memory card contains helpful preloaded  
information, including guided tours of your phone’s  
features.  
To insert your SIM card:  
1. With your phone powered off, slide the battery  
door latch on the side of the phone down. While  
holding the latch down, lift and remove the battery  
door.  
Insert the Memory Card  
1. With your phone powered off, slide the battery  
door latch on the side of the phone down. While  
holding the latch down, lift and remove the battery  
door.  
2. Remove the battery, and then use your thumbs to  
carefully slide the SIM card into your phone until it  
lies flat in the SIM card holder.  
4
2. Open the memory card slot cover and slide in the  
memory card until it clicks into place.  
Battery and Charger  
WARNING: Use only Nextel-approved or Motorola-approved  
batteries and chargers with your phone. The  
failure to use a Nextel-approved or Motorola-  
approved battery and charger may increase the  
risk that your phone will overheat, catch fire, or  
explode, resulting in serious bodily injury, death,  
or property damage.  
Important: For information on battery safety, see “Battery Use  
Nextel-approved and Motorola-approved batteries and  
accessories can be found at Sprint Stores or through  
Motorola. You may order online at www.nextel.com or by  
calling 1-866-866-7509.  
3. Close the memory card slot cover.  
Your phone’s Lithium Ion (Li-Ion) battery allows you to  
recharge it before it is fully drained.  
For more information about your phone’s memory  
When the battery reaches 5% of its capacity, your  
phone makes a sound and displays a message. When  
there are approximately two minutes of talk time left, the  
phone sounds an audible alert and then turns off.  
5
 
2. Insert the battery into the opening, making sure the  
connectors align. Gently press down to secure the  
battery.  
Note: Long backlight settings, searching for service, vibrate  
mode, browser use, and other variables may reduce  
the battery’s talk and standby times. See “Battery Tips”  
on page 24 for more details on extending battery life.  
Tip: Watch your phone’s battery level indicator and charge the  
battery before it runs out of power.  
Installing the Battery  
1. With your phone powered off, slide the battery  
door latch on the side of the phone down. While  
holding the latch down, lift and remove the battery  
door.  
3. Replace the battery door, pressing down firmly on  
it to ensure it is secured properly.  
6
 
Removing the Battery  
Charging the Battery  
1. Make sure the power is off so that you don’t lose  
any stored numbers or messages.  
Charge your battery as soon as possible so you can  
begin using your phone.  
2. Remove the battery cover and lift the battery to  
remove it.  
Always use a Nextel-approved or Motorola-approved  
desktop charger, travel charger, or vehicle power  
adapter to charge your battery.  
Using the Phone Charger  
Plug the flat end of the charger into the phone’s  
micro USB connector and the other end into the  
wall socket connector. Plug the wall socket  
connector to an electrical outlet.  
WARNING: Do not handle a damaged or leaking battery as  
you can be burned.  
3H  
With the approved Li-Ion battery, you can recharge the  
battery before it becomes completely run down.  
7
   
Sleep and Wake Up  
Turning Your Phone On and Off  
To conserve your battery, prevent  
accidental touches, or when you  
want to wipe smudges off your  
touchscreen, put the touchscreen to  
sleep by pressing Screen Lock # on  
top of the phone. To wake up the  
Turning Your Phone On  
Press and hold End/Power " for approximately  
two seconds.  
Screen Lock  
Button  
As your phone connects to the network, you see a  
connecting message. Your phone may require you to  
enter identifying information to use it or to access  
specific features.  
touchscreen, press Screen Lock # again and then  
Stretch to unlock  
drag  
to the right to unlock the screen.  
Activating Your Phone  
If you purchased your phone at a Nextel Store, it is  
probably activated and ready to use.  
Note: If your phone's SIM PIN is set, you will be prompted to  
enter your SIM PIN code when you turn on your phone.  
Press Menu /, enter the four-digit SIM code, and  
touch OK to allow phone transmissions as prompted.  
If your phone is not activated, please call Nextel  
Customer Service at 1-800-639-6111 from any other  
phone.  
Turning Your Phone Off  
Press and hold End/Power " to open the Power Key  
menu, where you can turn off the phone (Power off), or  
turn Airplane mode or Silent mode on or off.  
Tip: You must be in an area covered by the Nextel National  
Network when you first power up your phone.  
When you power up your phone the first time, it  
performs a series of security checks. For example, it  
verifies the phone is Nextel-approved and the correct  
SIM card is installed. If you don’t pass the security  
checks, your phone displays messages and screen  
8
     
prompts showing what to do next. If you still  
encounter security messages, call Nextel Customer  
Service at 1-800-639-6111 from any other phone.  
Set up additional email accounts, such as POP3,  
IMAP, or Microsoft™ Exchange.  
Import contacts from your SIM card.  
Select your keyboard type.  
Setup Wizard  
Tip: To type information in any of the setup steps, touch the  
text field to display the keyboard. To switch from portrait  
(vertical) to landscape (widescreen), turn the phone  
counter-clockwise.  
The first time you turn on your phone, a setup wizard  
appears and helps you get started.  
1. (Optional) If you want to change the primary  
language used by your phone, touch Change  
language and then touch a language.  
4. Touch Done to exit the setup wizard.  
Note: This phone supports data-intensive applications and  
services. It is strongly recommended that you purchase  
a data plan that meets your needs. Contact your  
service provider for details.  
2. Touch Start on the bottom right side of the screen.  
3. Follow the onscreen instructions to complete the  
wizard. To skip any steps or to proceed after  
completing a step, touch Next.  
Set up your Wi-Fi connection.  
Sign in to your existing Google™ Gmail account.  
If you don’t have a Google account, you can  
create one using the wizard.  
Tip: Remember to write down your user name and password,  
and keep them in a safe place.  
9
     
Setting Up Voicemail  
Account Passwords  
All unanswered calls to your phone are automatically  
transferred to your voicemail, even if your phone is in  
use or turned off. Therefore, it is recommended that you  
set up your voicemail and personal greeting as soon  
as your phone is activated.  
With Nextel service, you enjoy unlimited access to your  
personal account information and voicemail account.  
To ensure that no one else has access to your  
information, you need to create passwords to protect  
your privacy.  
1. Using your MOTOROLA i1, call your wireless phone  
number.  
Account Username and Password  
If you are the account owner, you will create an account  
username and password when you sign on to  
www.nextel.com. (Click Need to register for access? to get  
started.) If you are not the account owner (if someone  
else receives the bill for your service), you can get a  
sub-account password at www.nextel.com.  
2. Follow the system prompts to:  
Create your passcode.  
Record your name announcement.  
Record your greeting.  
Note: Voicemail Passcode: It is strongly recommended that  
you create a passcode when setting up your voicemail  
to protect against unauthorized access. Without a  
passcode, anyone who has access to your phone is  
able to access your voicemail messages.  
Note: When you go to www.nextel.com, you will be redirected  
to www.sprint.com by default. Follow the sign in  
instructions above to access your Nextel account.  
Voicemail Password  
For more information about using your voicemail, (see  
You will create your voicemail password (or passcode)  
when you set up your voicemail. See “Setting Up  
Voicemail” on page 10 for more information on your  
voicemail password.  
10  
       
From Any Other Phone  
Nextel Customer Service: 1-800-639-6111.  
Business Customer Service: 1-877-639-8351.  
Getting Help  
Managing Your Account  
Operator Services  
Online: www.nextel.com  
Operator Services provides assistance when you place  
collect calls or when you place calls billed to a local  
telephone calling card or third party.  
Access your account information.  
Check your minutes used (depending on your  
service plan).  
Touch  
Dialer, 0 and then press Talk `.  
View and pay your bill.  
For more information or to see the latest in products  
and services, visit us online at www.nextel.com.  
Enroll for online billing and automatic payment.  
Purchase accessories.  
Shop for the latest phones.  
View available service plans and options.  
From Your MOTOROLA i1  
Touch  
Dialer, *4 and then press Talk ` to  
check minute usage and account balance.  
Touch  
Dialer, *3 and then press Talk ` to  
make a payment.  
11  
   
Your Phone  
2. Phone Basics  
1. 2.5mm  
Headset Jack  
16. Screen Lock Button  
1:22 PM  
2. Volume  
Button  
15. Touchscreen  
3. Direct  
Connect  
Button  
14. Back Key  
Launch PTT  
Contacts  
13. Speaker  
Key  
4. OK Key  
OK  
Call log  
Email  
Messaging  
Browser  
12. Camera  
Button  
5. Home  
Key  
Note: The use of wireless phones while driving may cause  
distraction. Discontinue a call if you can’t concentrate  
on driving. Additionally, the use of wireless devices and  
their accessories may be prohibited or restricted in  
certain areas. Always obey the laws and regulations on  
the use of these products.  
6. Menu  
Key  
11. Micro USB  
Connector  
7. Talk Key  
10. End/Power  
Key  
8. Navigation  
Key  
9. Microphone  
12  
     
10. End/Power Key (") lets you end calls. Press and  
hold to open the phone options menu where you  
can turn the phone off, turn Airplane mode on or  
off, and turn Silent mode on or off.  
Key and Connector Functions  
1. 2.5mm Headset Jack lets you attach a headset.  
2. Volume Button lets you adjust the ringer volume  
from the home screen, the voice or speaker  
volume during a call, and the speaker volume  
while using the music player or other applications.  
11. Micro USB Connector lets you connect a charger or  
other accessories to your phone.  
12. Camera Button (j) activates the camera and lets  
3. Direct Connect (DC) Button lets you use Nextel  
you take pictures.  
Direct Connect®. (See page 32.)  
13. Speaker Key ()) lets you turn the speaker phone  
on or off during a call. From the home screen,  
pressing the Speaker Key turns Direct Connect  
speaker mode on and off.  
4. OK Key (r) selects the highlighted choice when  
navigating through a menu using the Navigation  
Key.  
5. Home Key (X) brings you back to the home  
screen. Press and hold to display the active apps  
menu.  
14. Back Key (%) returns you to the previous screen.  
15. Touchscreen input lets you access all the phone’s  
menus and features, enter text, dial phone  
6. Menu Key (/) lets you access the options menus  
(including Settings) from the home screen and  
context-sensitive menus from other screens.  
numbers, and more, using just your fingertips.  
16. Screen Lock Button (#) lets you lock and unlock  
the touchscreen.  
7. Talk Key (`) lets you make or receive calls,  
answer Call Waiting, or switch between two calls.  
8. Navigation Key lets you scroll through and highlight  
onscreen options.  
9. Microphone picks up your voice during a call.  
13  
 
The home screen extends beyond what you see on the  
initial screen to give you more room for adding  
shortcuts, widgets, and more. Flick the home screen  
left and right to see more panels or to add widgets or  
shortcuts.  
Home Screen  
The home screen gives you all your latest information  
in one place. It’s what you see when you turn on the  
phone or press Home X. Here’s the basic setup:  
1:22 PM  
1:22 PM  
1:22 PM  
1:22 PM  
Status Indicators  
Google search  
Notifications Bar  
Touch & drag this bar down  
to check notifications.  
Flick left or right to open  
more panels.  
Call log  
Email  
Messaging  
Browser  
Widgets  
Touch to open, or touch &  
Launch PTT  
Contacts  
Widgets  
hold to move or delete.  
You can add widgets, such as a clock, music player, or  
appointment calendar, to your home screens.  
Shortcuts  
Touch to open.  
Call log  
Email  
Messaging  
Browser  
To add widgets, press Menu / > Add > Widgets  
and then select a widget from the list. To open a  
widget, touch it  
Applications Tab  
Drag up to see  
all your apps.  
Note: Your home screen might look a little different.  
14  
     
Touch  
(the Applications tab) at the bottom of  
Shortcuts  
the home screen to open the app menu.  
To add shortcuts to the home screen, touch  
Running Multiple Apps  
(the Applications tab), and then touch and hold the  
shortcut you want. When the display switches to  
the home screen, drag the short cut to an empty  
space. You can also press Menu / > Add >  
Shortcuts.  
Your phone can run multiple apps simultaneously, so  
there is no need to close one app before opening  
another one.  
To open a new app while another is already running,  
press Home X to display the home screen. Touch  
and touch the app you want to open. To switch  
from one running app to another, press and hold  
Home X to display a list of currently running apps,  
and then touch the one you want. The list displays up  
to six running apps.  
Tip: To add widgets or shortcuts, you can also touch and hold  
a space on the home screen, touch Shortcuts or  
Widgets, and then select an item.  
Apps (Applications)  
Your phone comes with some apps (applications)  
already installed, and you can download and install  
more. To open an app, touch its icon.  
Search  
You can launch a Google search directly from the  
home screen.  
Applications Tab  
All the apps on your phone,  
including the apps that came with  
your phone and any you  
download and install, are listed in  
alphabetical order in your  
Applications menu.  
1. Press Menu / > Search or flick the home screen  
to the left to display the search widget.  
Alarm Clock  
Call log  
Browse
ator  
Camera  
Calendar  
Contacts  
2. Touch the text field to display the keyboard, and  
enter your search term.  
Camcorder  
15  
         
3. Touch  
to begin the search. To use voice  
This list identifies the symbols you’ll see on your  
phone’s display screen:  
search, touch  
and say a search topic, such as  
“pizza.”  
Battery Strength — A fuller battery indicates a  
greater charge. The “lightning” icon (bottom  
rows) indicates the phone is charging.  
Type, then touch the  
icon for a text search.  
Google search  
Signal Strength — More bars next to the  
antenna indicate a stronger signal.  
Touch for voice  
search.  
No Service — Your phone is without service.  
You cannot make or receive any type of call.  
Viewing Status and Notification  
Information  
Your phone’s display screen provides information  
about your phone’s status and notifications. To see  
your notifications, touch the notification bar and drag it  
down. Icons on the right tell you about your phone’s  
status.  
Phone In Use — Your phone is active on a  
phone call.  
Direct Connect In Use — Your phone is active  
on a Direct Connect call.  
Group In Use — Your phone is active on a  
Group Connect call.  
1:22 PM  
Talkgroup In Use — Your phone is active on a  
Talkgroup call.  
16  
   
Bluetooth In Use — Your phone is using  
Bluetooth. If this icon is blinking, your phone is  
in discoverable mode. If this icon is static, a  
Bluetooth connection is active.  
Internet — You are ready to browse the Internet  
or are browsing the Internet using a secure  
Active Phone Line — 1 indicates phone line 1  
is ready to make calls; 2 indicates phone line 2  
is ready to make calls.  
Airplane Mode — Your phone is set not to  
receive calls and other transmissions. See  
Call Forward — Your phone is set to forward  
TTY — You are ready to use your phone to  
make calls using a TTY (text telephone) device.  
Ringer Off — All sound is turned off on your  
Hearing Aid — Your phone is set for use with a  
hearing aid and is active on a phone call. See  
Speaker Off — Direct Connect sound is set to  
come through the earpiece rather than through  
the speaker.  
Speaker On — Direct Connect sound is set to  
come through the speaker rather than through  
the earpiece.  
Text Message — You have one or more text  
Vibrate — Your phone is set to vibrate and not  
to ring.  
Email — You have one or more emails.  
Gmail — You have one or more emails in your  
Gmail account.  
@
17  
Voicemail — You have one or more voicemails.  
Navigating Through Menus and  
Options  
Data Sync — Your phone is downloading email  
and synchronizing your calendar with your  
personal, Gmail, or Exchange accounts.  
Touch Tips  
Here are some tips on how to navigate around your  
phone.  
Wi-Fi — Your phone has established a Wi-Fi  
connection.  
GPS — Your phone’s GPS is active.  
Touch  
To choose an icon or option,  
touch it.  
Downloading — Your phone is downloading  
an app.  
Call log  
Email  
essing  
Browser  
Missed Call — You have one or more missed  
calls.  
18  
       
Touch and Hold  
Tip: When you drag or flick a list, a scroll bar appears on the  
right. Drag the scroll bar to move the list to a letter A - Z.  
To open special options, touch  
and hold an icon or other item.  
Try it: In the home screen, touch  
Contacts, and then  
touch and hold a contact to  
open options.  
1:22 PM  
Flick  
Dialer  
Call log  
Contacts  
Favorites  
All contacts  
To scroll through a list or move quickly, flick your finger  
up, down, or across the touchscreen (drag quickly and  
release).  
Me  
Home  
PTT  
Ashley Grovr  
Ashley Grover  
View contact  
Tip: When you flick through a long list, touch the screen to  
stop it from scrolling.  
Call Mobilr  
Send SMS/MMS  
Push to Talk  
Zoom  
In maps, touch  
bottom of the screen to zoom in  
or out. When viewing Web  
pages, touch the screen once to  
zoom in. To zoom out touch the  
screen twice, or touch  
bottom of the screen.  
or  
at the  
Drag  
1:22 PM  
To scroll through a list or  
move slowly, drag your  
Dialer  
Call log  
Contacts  
Favorites  
finger up or down the  
touchscreen. Try it: In the  
home screen, touch  
Contacts, and then  
drag your Contacts list up  
or down.  
Als  
Me  
at the  
H
Ashley Grove
Bomi Kim  
M
Book Club  
Members  
Chris Boomer  
PTT  
Work  
PTT  
Chris Hunter  
19  
My Sign  
Screen Timeout  
Draw on your screen to get to your favorite apps. To  
To change how long your phone waits before the  
open My Sign, touch  
>
My Sign.  
screen goes to sleep automatically, touch  
>
Settings > Sound & display > Screen timeout.  
Draw the sign for the action you  
want. For example, draw a “V” to  
go to voicemail.  
1:22 PM  
To put your phone to sleep and lock your screen, see  
To see which actions are already  
assigned to gestures, press  
Menu / > List Gestures. You’ll  
also see several gestures that  
are unassigned.  
Adjust Volume  
Press the Volume button to change  
the ring volume (in the home  
screen), or the earpiece volume  
Volume  
Button  
(during a call).  
To assign an action to a gesture,  
press Menu / > List Gestures,  
touch an unassigned gesture,  
and then touch an app from the  
list.  
Call Voicemail  
1-555-555-5555  
Rotate the Screen  
The touchscreen can rotate 90 degrees to switch  
between portrait (vertical) and landscape (widescreen)  
modes when you rotate your phone.  
To create a new gesture, press Menu / > New  
Gesture, select an action from the list, and draw a  
gesture to assign to the action.  
To set your screen to rotate automatically:  
Touch  
>
Settings > Sound & display >  
Orientation.  
Tip: Not all applications are designed to rotate.  
20  
Displaying Your Numbers  
Entering Text  
Touch  
Contacts and select the first contact. The  
Touchscreen Keyboard  
first contact in the Contacts list will always contain your  
phone’s information.  
You can open a display keyboard by touching a text  
field. To close the keyboard, press Back %.  
1:22 PM  
Text Entry  
Touch to open the  
Dialer  
Call log  
Contacts  
Favorites  
touchscreen keyboard.  
All contacts  
Search  
Touch to search  
contacts.  
Search contacts  
Me  
My Info  
Your details–always  
first in the list.  
Delete  
Return  
Home  
PTT  
Ashley Grover  
Bomi Kim  
Contacts List  
Touch to view  
contact information.  
Touch & hold to edit,  
delete, and more.  
Mobile  
PTT 1  
Shift  
Space  
Symbols/Numbers  
Book Club  
3 Members  
PTT 1  
Note: To automatically rotate the touchscreen to be right-side  
up when you rotate the phone, touch  
Menu Options  
Press Menu  
create, filter, and  
sync contacts.  
Chris Boomer  
>
to  
Settings > Sound & display > Orientation.  
21  
             
Select Keyboard Type  
Android Keyboard Typing Tips  
You can change the type of keyboard you’re using by  
touching and holding a text field and then touching  
Input method.  
Here are some tips for using your phone’s Android  
keyboard:  
To…  
Options  
?123  
Enter numbers Touch  
or symbols  
. To return to the  
ABC  
Android  
keyboard  
Standard keyboard.  
standard keyboard, touch  
.
?123  
ALT  
Enter alternate  
characters  
Touch  
from the  
screen. To  
?123  
ALT  
Swype™  
Keyboard for single hand text  
entry. Slide your finger from one  
letter to the next to enter text.  
return to the  
again.  
screen, touch  
Enter one  
capital letter  
Touch Shift  
Touch Shift  
Touch Delete  
.
Enter only  
capital letters  
twice.  
XT9 Text Input  
Offers improved foreign language  
support and word prediction.  
DEL  
x
Delete  
. Touch and hold  
to delete more than one character.  
Start a new line Touch Return  
.
22  
 
Swype Typing Tips  
Swype™ Text Entry  
To enter apostrophes in common words (like “I’ll”),  
drag through the n as though it was an apostrophe.  
Swype lets you enter a word with one continuous  
motion. To enter a word, just drag your finger over the  
letters.  
To enter several symbols, touch SYM.  
_
EN  
@
q
w
e# r 1 t2 y3  
u
i% o ( p)  
day  
To correct a word, double-tap it. Swype shows a  
small menu of other word options. Swype might also  
show a menu if it can’t guess your word.  
a8 s$ d4 f 5 g6 h+ j : k ;  
l
If Swype doesn’t know a word, you can still touch the  
letter keys to enter it. Swype remembers, so next time  
you can just drag over the letters.  
z ! x7 c8 v9 b0 n/ m?  
,
.
_
SYM  
SYM  
SYM  
_
EN  
@
Text Entry Settings  
When you use the touchscreen keyboard, your phone  
suggests words from your dictionary and chosen  
language.  
book  
q
w
e# r 1 t2 y3  
u
i%
(
p)  
a8 s$ d4 f 5 g6 h+ j : k ;  
l
For double  
letters, circle  
the letter.  
z ! x7 c8 v9 b0 n/ m?  
,
.
_
Touch  
>
Settings > Locale & text.  
To change the language and the style for your  
touchscreen keyboard, touch Select locale.  
_
EN  
@
Who  
q
w
e# r 1 t2 y3  
u
i% o ( )  
To  
To edit your dictionary, touch User dictionary.  
a8 s$ d4 f 5 g6 hj : k ;  
l
capitalize,  
go above  
the  
To change the sounds, corrections, and other  
settings for your touchscreen keyboard, touch  
Android keyboard, Swype, or XT9 Text Input.  
z ! x7 c8 v9 b0 n/ m?  
,
.
_
keyboard.  
23  
       
Battery Tips  
Tips and Tricks  
Your phone is like a small computer, giving you access  
to a lot of information and apps, with a touch display.  
Depending on what you use, that can take a lot of  
power.  
General Tips  
To…  
Return to the  
Press Home X.  
To conserve battery life between charges:  
home screen  
Reduce recording or watching videos, listening to  
music, or taking pictures.  
Press Talk `.  
See your  
Call log  
Disable or remove widgets that stream information to  
your home screen, such as news or weather. (See  
Press Screen Lock #.  
Sleep/wake  
your phone  
Reduce email updates: touch  
>
Email >  
Touch  
>
Settings >  
Set screen  
timeout  
Menu / > More > Account settings > Email check  
frequency > Every hour or Never to check for email  
manually.  
Sound & display > Screen timeout.  
Press and hold End/Power " >  
Silent mode.  
Turn sound  
on/off  
Turn off Bluetooth power: touch  
>
Settings > Wireless controls > Bluetooth.  
Search  
Press Menu / > Search.  
Turn off Wi-Fi: touch  
Wireless controls > Wi-Fi.  
>
Settings >  
Press and hold Home X.  
Show last few  
apps used  
Disable Google™ app updates: touch  
Settings > Data synchronization > Google >  
Background data.  
>
Press and hold End/Power " >  
Airplane mode.  
Turn airplane  
mode on/off  
24  
   
Reduce display brightness: touch  
Settings > Sound & display > Brightness > (dimmer  
setting).  
Decrease display timeout delay: touch  
>
in “Cool Down” mode, only emergency calls can be  
made.  
>
Accessories  
Settings > Sound & display > Screen timeout >  
(shorter setting).  
Your MOTOROLA i1 comes with the following  
accessories:  
Rugged Features  
A Li-Ion battery and charger.  
A128K SIM card.  
Your phone is designed to resist damage from  
exposure to certain rugged conditions. To help protect  
your phone, always make sure that the battery  
compartment and connector covers are closed and  
secure. You should also avoid prolonged or extreme  
exposure to those conditions.  
Various accessories are available for use with your  
MOTOROLA i1, including cases, vehicle power  
chargers, data cables, hands-free accessories, and  
more.  
To order additional accessories, go to www.nextel.com  
or call1-866-866-7509. You can also contact your  
Nextel Authorized Representative or stop by any Sprint  
Store. For information on Sprint Store locations, go to  
Battery Cool Down  
In very limited circumstances, such as where your  
phone has been exposed to extreme heat, “Cool  
Down” message screens will appear. To avoid possible  
damage to your battery and phone, you should follow  
these instructions until the phone is within its  
recommended temperature range. When your phone is  
25  
           
Using a Remote Direct Connect Button  
If you are using a headset or other optional accessory  
with a remote Direct Connect button, you can use the  
remote Direct Connect button for phone calls, Direct  
Connect calls, and Group Connect calls.  
For phone calls, use the remote Direct Connect button  
to answer calls, switch between calls, and end calls.  
Hold the remote Direct Connect button for less than  
two seconds to answer calls and switch between calls.  
Hold the remote Direct Connect button for more than  
two seconds to end calls.  
For Direct Connect calls and Group Connect calls, use  
the remote Direct Connect button as you would the  
Direct Connect button on your phone.  
When using a headset, the Direct Connect button on  
your phone works the same way as when you are not  
using a headset. Direct Connect and Group Connect  
sounds will be heard through the headset.  
26  
 
Direct Connect Calls allow two-way radio  
communication with another Direct Connect user  
within the Nextel National Network (page 32).  
3. Making and Answering  
Calls  
Group Connect Calls allow coast-to-coast two-way  
radio calling to up to 20 Nextel Direct Connect  
customers simultaneously (page 35).  
Nextel Direct Send allows you to send contact  
information in Direct Connect and Group Connect  
calls and send pictures in Direct Connect calls  
Talkgroup Calls allow two-way radio calling to up to  
100 Nextel Talkgroup customers simultaneously  
Note: To learn more about the differences between Nextel  
Group Connect calls and Talkgroup calls, please see  
Types of Calls  
With the Nextel National Network, Nextel Direct  
Connect, and your MOTOROLA i1, you have the  
following traditional wireless phone and Nextel Direct  
Connect services available to you:  
Digital Wireless Phone Calls offer clear calls and other  
services, such as missed call notification, Three-Way  
Calling, and speakerphone.  
27  
   
Phone Calls  
1:22 PM  
Making Calls  
Dialer  
Call log  
Contacts  
Favorites  
Placing a traditional wireless phone call from your  
MOTOROLA i1 is as easy as making a call from any  
landline phone.  
Delete  
Touch to delete a digit you  
entered.  
555-555-5555  
1
2
3
ABC  
DEF  
Contacts  
Touch to open, then touch  
an entry to call.  
1. Touch  
press Talk `.  
Dialer, enter a number, and then  
4
5
6
2. Press End/Power " when you are finished.  
GHI  
JKL  
MNO  
Call Log  
Touch to open, then touch the  
icon to the left of an entry to  
call.  
You can also make calls from your phone by selecting  
numbers directly from Contacts (page 31) or your Call  
8
9
7
PQRS  
TUV  
WXY  
Call  
0
#
Enter a number and  
*
+
press  
.
Answering Calls  
Press Talk ` to answer an incoming call.  
Note: When your phone is off, calls go directly to voicemail.  
Your phone notifies you of incoming calls by any  
combination of ringing or vibrating, the backlight  
28  
     
illuminating, or the screen displaying an incoming call  
message.  
Emergency Calls  
Your phone supports emergency calling. Emergency  
phone calls can be made even when your SIM card is  
blocked or not in your phone.  
If the incoming call is from a number stored in your  
Contacts, the entry’s name is displayed. The caller’s  
phone number may also be displayed, if available.  
Touch  
Dialer, enter 911 and press  
Ending a Call  
Talk ` to be connected to an emergency  
response center. If you are on an active call, you  
must end it before calling 911. If your phone is  
locked, touch the Emergency call button at the  
bottom of the screen.  
To end a call, press End/Power ".  
Missed Phone Calls  
Missed phone calls are forwarded to voicemail. When  
you do not answer an incoming call, you will see a  
Missed Call notification.  
When you make an emergency call, your phone’s GPS  
Enabled feature can help emergency service  
personnel find you, if you are in a location where your  
phone's GPS antenna has established a clear view of  
the open sky and your local emergency response  
center has the equipment to process location  
Because of the limitations of this feature, always  
provide your best knowledge of your location to the  
emergency response center when you make an  
emergency call.  
To display a Missed Call entry from the notification bar:  
Drag the notification bar down and touch the  
missed call notification.  
To display a Missed Call entry from the home screen:  
1. Press Talk ` or touch  
Dialer > Call Log.  
2. Touch an entry.  
29  
 
In-Call Options  
Important: Always report your location to the 911 operator  
when placing an emergency call. Some  
designated emergency call takers, known as  
Public Safety Answering Points (PSAPs) may not  
be equipped to receive GPS location information  
from your phone.  
Press Menu / during a call to  
display a list of available in-call  
features. To select an option,  
touch it. The following options  
may be available:  
1:22 PM  
If you have not registered on the network,  
emergency calls cannot be placed while your  
SIM card is in your phone.  
Swap call to switch between to  
active calls.  
Show Dialpad  
Merge call to initiate a three-  
If you are bringing your phone number to Nextel  
from your previous carrier, you may receive a  
temporary telephone number while your Nextel  
phone is being programmed with your  
permanent phone number. If you make a call to  
911 and the call fails, the 911 emergency  
response center will not be able to call you back  
on your Nextel phone if in the meantime, your  
Nextel phone has been programmed with your  
permanent telephone number. If the call is  
disconnected before location and details have  
been provided, call 911 again and advise that you  
were disconnected.  
way call.  
Swap call  
Hold  
Merge call  
Mute  
Add call  
Speaker  
End call  
Bluetooth  
Add call to place a second call.  
End call to end the call.  
Hold to place a call on hold.  
Mute to mute your phone’s microphone. Touch Mute  
again to unmute your phone’s microphone.  
Speaker to route the phone’s audio through the  
speaker or the earpiece.  
Tip: You can also press Speaker ) to turn the speaker on  
and off.  
WARNING: Because of higher volume levels, do not place the  
phone near your ear during speakerphone use.  
30  
 
Bluetooth to disconnect from a Bluetooth device.  
2. Touch Search contacts.  
3. Enter the first few letters of a Contact's name. Your  
phone will display a list of matching contact  
entries.  
Saving a Phone Number  
1. Touch  
Dialer, enter a phone number, and  
press Menu /.  
4. To display the Contacts entry, touch the contact  
name. Touch a phone number to place a call.  
2. Touch Add to contacts.  
3. To store a new entry, touch Create new contact.  
Phone Numbers With Pauses  
You can dial or save phone numbers with pauses for  
use with automated systems, such as voicemail,  
conference call, or credit card billing numbers.  
– or –  
Search for an existing contact name and touch it to  
open the contact.  
4. Enter or edit information as necessary, and then  
scroll to the bottom of the entry and touch Done to  
save the Contact.  
There are two types of pauses available on your phone:  
Wait sends the next set of numbers when prompted.  
Pause automatically sends the next set of numbers  
after three seconds.  
For more information about Contacts, see “8. Contacts”  
Note: You can have multiple pauses in a phone number and  
combine waits and pauses.  
Finding a Number  
To dial or save phone numbers with pauses:  
To find Contacts entries, you can either scroll through  
the list by dragging your finger up or down the screen,  
or you can search Contacts entries by name.  
1. Touch  
Dialer and enter a phone number.  
2. Touch and hold * until the letter P appears. The P  
represents a three-second pause. For a longer  
1. Touch  
Contacts.  
31  
         
pause, touch and hold * again to enter more  
pauses. Each P represents a three-second pause.  
Making a Call From the Call Log  
1. Touch  
Dialer > Call Log.  
– or –  
2. Touch the icon to the left of an entry to place a call.  
Touch and hold * until the letter W appears. The  
W means your phone waits before dialing further. A  
message appears asking about sending the rest of  
the digits.  
Making a Phone Call While in a Direct  
Connect Call  
3. Enter additional numbers.  
4. Press Talk ` to dial the number.  
– or –  
Press Menu / > Call contact while in an active  
Direct Connect call to initiate a phone call to the  
other person (if their mobile phone number is  
stored in Contacts).  
Press Menu / > Add to contacts to save the  
number in your Contacts.  
Nextel Direct Connect  
Making a Call From Contacts  
Nextel offers the following Nextel Direct Connect®  
services:  
Direct Connect® allows instant two-way radio  
communication with another Direct Connect user  
anywhere on the Nextel National Network (U.S.).  
1. Touch  
Contacts.  
2. Touch an entry to open it.  
3. Touch a phone number to place a call.  
International Direct Connect allows Direct Connect  
calling to and from select countries.  
32  
         
Group Connect® allows nationwide Direct Connect  
calling to up to 20 other Direct Connect users at  
TalkgroupSM allows Direct Connect calling to up to  
100 Nextel subscribers in the same Direct Connect  
Dialing Direct Connect Numbers  
Every Direct Connect number has three parts:  
An area ID.  
A network ID.  
A member ID.  
See www.nextel.com for more details on these Direct  
Connect services. Pricing for each of these services is  
based on your service contract.  
An asterisk separates each part (for example:  
999*999*9999). When you enter a number containing  
all three parts, you must separate them with asterisks.  
Note: The number of digits in each part of a Direct Connect  
number may vary. For example, your Direct Connect  
number may be formatted as 999*999*9999, while  
another valid number may appear as 555*555555*55.  
Making Direct Connect Calls  
1. Touch  
Dialer and enter a Direct Connect  
If you are calling or saving a Direct Connect number for  
a Sprint phone with Direct Connect capabilities, the  
Direct Connect number may be the same as the  
wireless phone number. When dialing or saving the  
Direct Connect number, insert asterisks in place of  
hyphens (913*555*1234).  
2. Press and hold the Direct  
Connect (DC) button on the left  
side of your phone. Begin  
talking after your phone emits  
a chirping sound.  
Direct  
Connect  
Button  
Tip: When you store a Direct Connect number in Contacts, be  
3. Release the DC button to listen.  
sure to include the entire number, including the asterisks.  
A Direct Connect call ends automatically after there is  
no activity on the call for several seconds.  
33  
     
Using Just the Member ID  
Answering Direct Connect Calls  
If you are contacting someone sharing your network  
and area IDs, you only need to enter the member ID  
(the last part of the number).  
When you receive a Direct Connect call, your phone  
emits a tone or vibrates. You then hear the voice of  
your caller.  
1. Touch  
Dialer and enter a member ID.  
1. Wait for the caller to finish speaking.  
2. Press and hold the DC button.  
2. Press and hold the DC button. Continue as you  
would on any Direct Connect call.  
Making Direct Connect Calls From Contacts or  
the Call Log  
A Direct Connect call ends automatically after there is  
no activity on the call for several seconds.  
If you have numbers stored in Contacts (page 82) or  
the Call log (page 78), you can use these numbers to  
make calls.  
Direct Connect Timeout  
You can extend the automatic timeout of a Direct  
Connect call by about 30 seconds using the Resume  
DC setting.  
1. Touch  
Contacts, or touch  
Dialer >  
Call log.  
2. Touch an entry and then press and hold the DC  
button to call the entry’s Direct Connect number.  
Touch  
>
Settings > Call settings >  
Direct Connect settings > Resume DC.  
Tip: You can make Direct Connect calls while viewing entry  
details on either list. Display the entry details or My Info  
from another phone (in the Call log) and press and hold  
the DC button.  
34  
     
One Touch Direct Connect  
You can customize the DC button for quick access to  
Direct Connect functions.  
Group Connect  
A Group Connect call is similar to a Direct Connect call  
to one user, but is made to multiple Direct Connect  
subscribers at once. You can create Groups from your  
phone and call up to 20 other Group Connect-  
compatible phones* anywhere on the Nextel National  
Network. You can create a Group for one-time use or  
store it to Contacts so you can call it at any time.  
Touch  
>
Settings > Call settings >  
Direct Connect settings > One Touch DC.  
Options  
Off  
Turn off One Touch DC.  
Launch DC  
Contact List  
Open a list of Direct Connect  
contacts on your phone.  
Note: In order to store Groups to your MOTOROLA i1, you  
must use the 128K SIM card that came with your  
phone. The 128K SIM card is labeled “Nextel 600  
Contcs & 25 Grps”. With this SIM card, a maximum of  
25 groups can be added to your MOTOROLA i1. Group  
entries created with your MOTOROLA i1 may not be  
readable by older iDEN SIM-based phones.  
DC a selected  
contact  
Start a Direct Connect call with the  
selected contact.  
DC the most  
recent number  
Start a Direct Connect call with the  
most recent Direct Connect  
number in the Call log.  
Tip: You can also add the One Touch DC widget to your  
Making Group Connect Calls  
home screen. See “Widgets” on page 14.  
1. From Contacts or the Call log list, touch a Group to  
open it.  
2. Press the DC button.  
.
35  
     
3. Touch Add Members and select members to add.  
Answering Group Connect Calls  
4. Touch Done(Selected) and then scroll to the  
bottom of the entry and touch Done to save the  
contact.  
Proceed as if answering a Direct Connect call from  
one user. Only one person at a time may speak on  
a Group Connect call.  
Starting a Group Connect Call With a  
Direct Connect Number  
Creating Groups in Contacts  
1. Touch  
Contacts > Menu / > New group.  
1. Touch  
Contacts > Menu / > New group.  
2. Touch the icon to the left of the entry names to  
select the group members.  
2. Select the group members.  
3. Touch View.  
3. Touch Save(Selected) to store the Group in  
Contacts.  
4. When prompted, press the DC button.  
Note: If you do not assign a name, the Group is named  
(Group).  
Removing Members or Groups  
4. Scroll to the bottom of the entry and touch Done.  
To remove a member from a Group:  
1. From Contacts, touch a Group to open it, and then  
press Menu / > Edit group.  
Adding Group Members  
To add member to a Group stored in Contacts:  
2. Touch a member’s contact to remove it from the  
Group.  
1. Touch  
Contacts and touch a Group to  
open it.  
3. Scroll to the bottom of the entry and touch Done.  
2. Press Menu / > Edit group.  
36  
       
To delete a Group from Contacts:  
1. Touch a Group to open it.  
2. Press Menu / > Delete group.  
3. Touch OK.  
The number of members who are participating in the  
Group Connect call.  
Nextel Direct Send  
Nextel Direct Send lets you use Direct Connect calls to  
exchange pictures, My Info, contact information, and  
Groups with other phones that have this capability.  
Storing Groups  
To store a group to Contacts from the Call log list:  
Nextel Direct Send cannot be used during Talkgroup  
calls. Pictures cannot be sent in Group Connect calls.  
1. From the Call log list, touch a Group to open it, and  
then touch View participant list.  
Sending a Picture  
2. Touch Add to contacts.  
3. Scroll to the bottom of the entry and touch Done to  
Sending a Picture During a Call  
save the contact.  
You can send a picture at any time during a Direct  
Connect call, whether you made or received the call.  
(Additional charges may apply.)  
Group Connect Call Information  
While you are in a Group Connect call, the following  
appears on the screen:  
You cannot talk or listen on a Direct Connect call while  
a picture is being transmitted. Other activities, such as  
searching for a picture, do not prevent you from talking  
or listening.  
The name of the Group.  
The name or the Direct Connect number of the  
person speaking.  
37  
       
To send a picture during a call:  
Tip: When a person sends you My Info from his or her phone,  
you can then easily store this information to Contacts  
from the Call log list.  
1. While in a Direct Connect call, press Menu / >  
Share picture. A list of pictures that can be included  
in a Direct Connect call appears.  
To start a call by sending a picture:  
2. Select a picture and press the DC button to send it.  
1. Touch  
>
Media Gallery > All Pictures.  
3. Wait while the picture is transmitted. The Direct  
Connect call is temporarily interrupted while a  
picture is transmitted.  
2. Touch and hold a photo, then touch Share.  
3. Touch DC, and touch DC contacts or DC call log.  
These names have Direct Connect numbers and  
IP addresses stored.  
4. When prompted, press the DC button to resume  
the Direct Connect call.  
4. Select a name and press the DC button to send  
the picture.  
Note: The first time you send a stored picture after turning the  
phone on, the message Picture fees may apply  
appears and you are prompted to respond. Touch OK  
to send the picture. Touch Cancel to cancel.  
5. When prompted, press the DC button to resume  
the Direct Connect call.  
Starting a Call by Sending a Picture  
Receiving a Picture  
You can start a call by choosing a stored picture from  
the Media Gallery.  
When someone sends you a picture using Nextel  
Direct Send, your phone emits a tone or vibrates and a  
message appears on the display asking you to accept  
the picture.  
To do this, you must have the recipient’s Direct Connect  
number and IP address stored in your Contacts.  
Pictures you receive are saved to your phone’s memory  
and are accessible through the Media Gallery.  
38  
 
To accept a picture:  
Sending My Info  
1. When you see the message asking you to accept  
the picture, touch Accept. (To decline the picture,  
touch Reject.)  
You can control what portion of the information in My  
Info is sent, and whether it is sent automatically in every  
Direct Connect call or only when you choose to send it.  
2. Wait while the picture is transmitted. The Direct  
Connect call is temporarily interrupted while a  
picture is transmitted.  
Note: When you send your contact information, certain  
information, such as street addresses or custom entries,  
chat addresses, organizations, and notes cannot be  
included.  
3. When prompted, press the DC button to resume  
the Direct Connect call.  
The information your phone sends always includes My  
Name and Direct Connect.  
Note: The first time you accept a stored picture after turning  
the phone on, the message Picture fees may apply  
appears and you are prompted to respond. Touch OK  
to accept the picture. Touch Cancel to cancel.  
It may include Line 1, Line 2, Direct Connect, and Group  
ID depending on the options provided by your service  
provider and how you set your sending options.  
Tip: To stop the transmission before it is finished, touch  
Note: The My Info feature gets its information from your  
phone’s contact entry. To add more information to My  
Info, edit your phone’s contact entry, and then select the  
additional fields in the Select info to share screen.  
Cancel.  
Sending My Info and Contact Information  
The default setting is Line 1 only.  
When you send My Info or contact information using  
Nextel Direct Send, the information you send appears  
on the display of the receiving phone. After the call, the  
information appears on that phone’s Call log list.  
To change which fields are sent:  
1. Touch  
>
Settings > Call settings >  
Direct Connect settings > Sharing contact info >  
Select info to share.  
39  
     
2. A checkmark appears next to the fields that will be  
3. Touch Share via DC.  
sent. To add or remove the checkmark, touch it.  
4. Touch a Contact or Call log entry to select it.  
3. When you are finished, touch Save.  
5. When prompted, press the DC button to send the  
information.  
To control whether your information is sent automatically:  
Touch  
>
Settings > Call settings >  
Sending Contact Information  
Direct Connect Settings > Sharing contact info >  
Share My Info.  
You can send contact information by selecting a  
Contacts entry.  
Note: When you receive your phone, it is set to send your  
Contacts entries that contain only addresses cannot be  
sent. When Contacts entries are received, they do not  
include ringtones or pictures.  
information automatically.  
To send My Info during a call:  
1. While in a Direct Connect call, press Menu / >  
To send contact information during a call:  
Share my info.  
1. While in a Direct Connect call, press Menu / >  
Share contact.  
2. When prompted, press the DC button to send the  
information.  
2. Select a contact to send  
To start a call by sending My Info:  
3. When prompted, press the DC button to send the  
information.  
1. Touch  
Contacts.  
2. Touch and hold the contacts entry containing your  
Note: If the Contacts entry you scrolled to is a Group, you may  
be prompted to allow yourself to be a part of the group  
being sent. Touch OK to become part of the group.  
phone’s information. This contact will always be the  
first entry in the contacts list and will have  
its right.  
to  
40  
 
To start a call by sending contact information:  
Talkgroups  
1. From Contacts, touch and hold a contacts entry.  
A Talkgroup is a predetermined group of Direct  
Connect users, created by an account administrator.  
Talkgroups can contain up to 100 members.  
2. Touch Share via DC.  
Note: If the Contacts entry you scrolled to is a Group, you may  
be prompted to allow yourself to be a part of the group  
being sent. Touch OK to become part of the group.  
Difference Between Group Connect and  
Talkgroup Calls  
In a Group Connect call, you or another caller  
determines who can participate in the call. By contrast,  
participation in a Talkgroup is determined by an  
administrator. Here are the ways Group Connect and  
Talkgroup calls differ.  
3. Select a recipient by touching a DC Contact or DC  
Call Log entry.  
4. When prompted, press the DC button to send the  
information.  
Receiving My Info or Contact Information  
When you receive My Info or contact information from  
Group Connect Talkgroup  
another phone,  
To view the information while still in the Direct Connect call:  
Press Menu / > View Contact.  
appears on the display.  
Group Icons  
Nationwide  
Limited to local  
market and network  
(fleet)  
Geography  
You can also view My Info from other phones on the  
21 (including  
originator)  
100  
Maximum  
Group Size  
41  
                 
Adding More Talkgroups  
Group Connect Talkgroup  
Dynamically,  
via your phone administrator using  
Talkgroup  
Predefined, via Nextel  
Setup  
You can be included in additional Talkgroups by doing  
one of the following:  
Using Talkgroup Management at www.nextel.com. You  
must be an account administrator to use Talkgroup  
Management.  
Management  
Joining a Talkgroup  
To participate in a Talkgroup, the account administrator  
must first add you to the membership and then you  
must “join” the Talkgroup.  
Contacting your Nextel Sales Representative at the  
time of activation.  
Making Talkgroup Calls  
1. Touch  
open it.  
Contacts and touch a Talkgroup to  
1. Touch  
Talkgroup number.  
– or –  
Dialer, touch  
, and then enter the  
+
2. Touch Join.  
You can now receive communications from other  
members of this Talkgroup.  
Select the Talkgroup from Contacts or the Call log  
list.  
You will hear all active Talkgroup conversations on your  
2. Press the DC button and continue as if making a  
Direct Connect call.  
phone. To silence them, touch  
>
Settings >  
Call settings > Direct Connect settings > Silence  
Talkgroups.  
42  
 
Receiving Talkgroup Calls  
Note: You can send a Call Alert from the Call log or Contacts.  
Touch an entry with a Direct Connect number and then  
touch Send Alert.  
Answer it as you would a regular Direct Connect  
call. Only one person at a time may speak on a  
Talkgroup call.  
Responding to a Call Alert  
During and immediately after a Talkgroup call ends,  
press Menu / > Options to display any available  
options.  
Note: You can set a distinctive ringer for Call Alerts. See  
To answer a Call Alert:  
Call Alerts  
Press the DC button. This will start a Direct  
Connect call to the sender.  
Call Alerts let you notify others that you want to  
communicate with them using Direct Connect. When a  
user receives a Call Alert, the phone sounds a tone  
and displays your name or Direct Connect number.  
To dismiss a Call Alert:  
Touch Dismiss.  
To store a Call Alert in Notifications:  
Touch Later.  
Sending Call Alerts  
1. Touch  
Dialer, enter a Direct Connect  
number and press Menu / > Send Alert.  
Note: The Call log list also stores Call Alerts you have  
received. They appear as Direct Connect calls. Call  
Alerts remain in your Call log list until you delete them  
or until they reach the end of the list.  
2. When prompted, press the DC button to send the  
Call Alert.  
43  
     
3. Press the DC button to begin the call.  
This removes the Call Alert from the queue.  
To send a Call Alert to the sender:  
Using the Call Alert Notification  
When you store a Call Alert, it remains in notifications  
until you clear the notification by opening it, or go into  
the Call log.  
1. Touch  
Dialer > Call log.  
Viewing Call Alerts  
2. Touch a Call Alert entry to open it and touch Send  
Alert.  
1. Drag the Notification bar down from the top of the  
screen.  
3. When prompted, press the DC button.  
Deleting Call Alerts  
2. Scroll through the list.  
Viewing Call Alert Date and Time  
1. Touch the Call Alert notification.  
To delete all Call Alerts from Notifications:  
1. Drag the Notification bar down from the top of the  
screen.  
2. In the Call log screen, touch the Call Alert.  
2. Touch Clear notifications.  
Responding to Call Alerts in the Queue  
Note: Touching Clear Notifications will clear all of your  
After you queue a Call Alert, you can respond to it by  
making a Direct Connect call to the sender or sending  
a Call Alert to the sender.  
Notifications, not just your Call Alerts.  
To make a Direct Connect call to the sender:  
1. Touch the Call Alert notification to open the Call  
log.  
2. Touch the Call Alert Entry.  
44  
       
Call Status and Completion  
After an failed incoming or outgoing Direct Connect  
call or Call Alert, you can send a message to the caller  
or intended recipient.  
To set up a message for incoming or outgoing calls:  
1. Touch  
>
Settings > Call settings > Auto  
Text reply > Incoming call or Outgoing call.  
2. Select from Off, Ask me to send text, or Always send  
text.  
3. Create a message to be sent, and touch Update.  
To send a message after receiving or making a call:  
1. After a failed incoming or outgoing Direct Connect  
call, within five seconds, Send text message to will  
appear.  
2. Touch your default message to send it, touch  
Create new message to send a new message, or  
touch Cancel.  
45  
Receiving Messages  
4. Service Features:  
The Basics  
When you receive a Multimedia Messaging Service  
(MMS) message, or text message (SMS), you have two  
ways to access the message:  
Respond to the message notification that appears  
when the message is received.  
Access the message later through Messaging.  
Message Notifications  
When you receive a message, your phone notifies you  
with an icon in the notification bar and a notification  
tone or vibration.  
For information on notification options, see “Setting  
46  
       
your password. Enter the last seven digits of your  
Nextel PTN. For example: 5557777. This is your  
temporary password. Follow the system instructions to  
complete your mailbox setup.  
Voicemail  
Tip: To receive voicemail messages, you must first set up your  
voicemail box.  
You are in the main voicemail menu when you hear the  
voicemail system options.  
If you are bringing your phone number from another  
carrier, we suggest you set up your voicemail box after  
the number you brought to Nextel is active on your Nextel  
phone and your temporary phone number is deactivated.  
If you set up your voicemail box prior to this, all messages  
and all settings (including your greeting and password)  
will be lost when the number you have brought to Nextel  
becomes active.  
For details on using your voicemail, follow the audio  
prompts provided by the voicemail system.  
Playing Messages  
To listen to your voicemail messages Touch  
Dialer and touch and hold 1. You will be  
connected to your voicemail box.  
Setting Up Your Voicemail Box  
To access your voicemail messages from another  
phone, dial your wireless phone number. When  
you hear the voicemail greeting, press * and then  
enter your voicemail passcode.  
Using your MOTOROLA i1, dial your ten-digit Nextel  
Personal Telephone Number (PTN). For example:  
7035557777. Follow the system instructions to create a  
new four- to seven-digit password, record your name,  
and record a greeting. When the system says, “Thank  
you for using Nextel Voicemail,” your mailbox is set up.  
Multimedia Messages (MMS)  
If you are setting up your voicemail from a phone other  
than your MOTOROLA i1, dial your ten-digit Nextel PTN.  
When you hear the greeting, press * to access your  
voicemail box. The system will prompt you to enter  
Multimedia Messaging Service (MMS) lets you send  
and receive messages that may include text, pictures,  
and audio recordings.  
47  
                     
Your MMS address is [email protected].  
Your PTN is your ten-digit Nextel Personal Telephone  
Number.  
Subject — the subject line. To add a subject, press  
Menu / > Add subject and enter a subject.  
Attach — one or more attachments. These may be  
pictures, ringtones, or audio files, including voice  
records that you create while creating the message.  
To add an attachment, press Menu / > Attach.  
Note: Most common phone-to-phone text messages are sent  
and received as MMS messages on your MOTOROLA  
i1. Text messages sent from other phones or mobile  
devices to your phone number arrive as MMS  
messages.  
To send a message, you must address it to at least one  
recipient. All other message fields are optional and you  
can fill them in any order.  
Accessing MMS Messages  
Entering Text  
Touch  
To open a message:  
Touch a message thread.  
>
Messaging.  
In message fields that require you to enter text, touch  
the message field to display the keyboard. If the  
keyboard is already displayed, begin typing whenever  
the field is highlighted.  
Creating and Sending Messages  
Each message you create may contain the following  
fields:  
Message Size  
You can create and send messages of up to 100 KB,  
including attachments, for MMS.  
To — the phone numbers or email addresses of one  
or more recipients.  
Message — the body of the message. This may  
include text, pictures, ringtones, or voice records.  
48  
 
Sending or Canceling  
Adding More Message Options  
To send the message at any time after it has been  
addressed:  
1. To create the subject line, press Menu / > Add  
subject, enter a subject, and touch Next.  
2. To attach a picture, audio, voice recording, or  
video, press Menu / > Attach and then select an  
option to attach a file.  
Touch Send.  
Creating a Message  
1. Touch  
>
Messaging > New message.  
3. To send the message, touch Send.  
2. Address the message:  
Replying to a Message  
Touch To. Enter the phone number, contact name  
or email address from the keyboard. Use a  
comma to separate multiple phone numbers or  
email addresses. Once you begin typing, your  
phone will show a list of contacts that are possible  
matches for the letters you have typed.  
You can reply to a message while you are viewing it.  
To reply to a message:  
1. Touch a message to open it.  
2. Touch the message field at the bottom of the page  
to enter your message.  
3. Enter or edit the body of the message:  
Touch the message field and then enter text using  
3. Touch Send.  
the keyboard.  
More Ways to Begin a Message  
4. To send the message without additional options,  
In addition to beginning a message from Messaging,  
you can begin a message from Contacts, the Call log  
list, the home screen, or the Media Gallery.  
touch Send.  
49  
To begin a message from Contacts:  
1. From the Contacts list, touch an entry.  
2. Touch Text mobile.  
Accessing Saved Drafts  
1. Touch  
>
Messaging.  
2. Draft messages have “Draft” in red letters next to  
them on the right.  
3. Create and send the message.  
To begin a message from the Call log list:  
1. From the Call log list, touch an entry.  
2. Touch Send text message.  
3. Touch the message to open it and finish  
composing your message.  
Forwarding Messages  
3. Create and send the message.  
To begin a message from the Media Gallery:  
1. Touch  
>
Messaging.  
2. Touch a message thread to open it.  
3. Touch and hold a message and then touch  
Forward.  
1. From the Media Gallery, touch and hold a picture or  
video.  
4. Address, edit, and send your message.  
2. Touch Share > Messaging.  
3. Create and send the message. The selected file is  
automatically included as an attachment.  
Receiving a Message  
When you receive an MMS message, a message  
notification appears on the notification bar.  
Drafts  
To view the message:  
Messages you are creating are automatically saved as  
drafts when you exit the message screen. The  
message must be addressed to someone in order for it  
to be saved as a draft.  
Drag the notification bar down from the top of the  
screen and touch the message notification.  
50  
   
This icon  
that you have a new message.  
appears on the display, reminding you  
3. Touch OK to confirm.  
To delete message threads:  
1. Touch and hold a message thread and then touch  
Navigating a Message  
As you scroll through a message, numbers, email  
addresses, and Web addresses are highlighted.  
Delete thread.  
2. Touch OK to confirm.  
Forwarding  
Pictures and audio recordings are also highlighted.  
1. Touch a message thread to open it.  
Attachments  
2. Touch and hold a message and then touch  
Forward.  
Messages may contain pictures or audio files as  
attachments.  
3. Address, edit, and send your message.  
If a message contains a picture or audio file as an  
attachment, touch the attachment to view the picture or  
play the audio file.  
Embedded objects and attachments are included  
when you forward a message.  
Calling a Number in a Message  
Actions for Received Messages  
If any field in a message contains a phone number,  
Direct Connect number, or Talkgroup ID, you can call  
or send a Call Alert to that number.  
Deleting  
To delete messages:  
To make a call to a number in a message:  
1. Touch a message thread to open it.  
1. View the message.  
2. Touch and hold a message and then touch Delete  
message.  
51  
           
2. Touch a number and press Talk ` to make a  
phone call or press the DC button to make a Direct  
Connect call.  
2. Touch and hold the message to display the  
message options, and then touch Add <item> to  
Contacts.  
To send a Call Alert to a Direct Connect number in a  
message:  
3. Touch Create new contact to store the number in a  
new entry, or touch an entry to store the  
information to an existing entry.  
1. View the message.  
4. To change the contacts type (Mobile, Home, Work,  
etc.), touch the type next to the number or address  
and select a type.  
2. Touch the Direct Connect number and then press  
Menu / > Send Alert.  
3. Press the DC button.  
5. Scroll to the bottom of the entry and touch Done  
To make a Talkgroup call to a Talkgroup ID in a message:  
1. View the message.  
when you have finished entering the information.  
Going to a Website  
2. Touch the Talkgroup ID and then press Menu / >  
Join Talkgroup.  
If a message contains one or more Web addresses,  
you can go to the website.  
3. Press the DC button.  
1. View the message.  
Storing Message Information to Contacts  
2. Touch the body of the message to display the  
Select action screen, and then touch the Web  
address. The Web page will open in your browser.  
If a message you receive contains a phone number,  
Direct Connect number, Talkgroup ID, or an email  
address in any of the fields, you can store this  
information to Contacts.  
Note: The entire Web address must appear in the message.  
Otherwise, you cannot go to the website.  
1. View the message.  
52  
 
Saving Attachments  
Caller ID Blocking  
1. View a message.  
Caller ID allows people to identify a caller before  
answering the phone by displaying the number of the  
incoming call. If you do not want your number  
displayed when you make a call, follow these steps.  
2. Touch and hold an attachment and then touch  
Copy attached to SD card.  
Text Messaging (SMS)  
Per-Call Blocking  
To block delivery of your number for a single phone call:  
With text messaging (SMS), you can receive instant text  
messages from another messaging-ready phone or  
from an email account.  
Touch *67 before dialing the call.  
Your phone's SMS address is [email protected].  
Your PTN is your ten-digit Personal Telephone Number.  
Your Nextel phone number cannot be blocked from  
calls made to 911, 800, 855, 866, 877, 888, or other  
toll-free phone numbers.  
Note: Most traditional phone-to-phone text messages arrive  
as MMS messages on your MOTOROLA i1. Your  
phone can send and receive MMS messages.  
Per-Line Blocking  
You can request that Nextel Customer Service  
permanently block delivery of your phone number on  
every call you make. In this case, you may need to  
display your number for certain calls.  
Your phone can receive SMS text messages, but it  
cannot send them.  
Accessing Text Messages  
To show your number on a per-call basis:  
When you receive a text message, you will see an  
alert. Touch Messaging and touch the  
message thread to open it.  
>
Touch *82 before dialing the call.  
53  
           
Call Waiting  
Making a Second Call  
Call Waiting lets you receive a second call while on an  
active call. Call Waiting is always available, unless you  
turn it off for a specific call.  
1. Place or receive a phone call.  
2. While the call is active, press Menu / > Add call.  
(The first call is placed on hold.)  
If you are on a call and receive a second call, your  
phone emits a tone and displays a message.  
3. Enter a second phone number and press Talk `  
to place the call.  
To accept the second call and put the active call on hold:  
Note: For quick ways to enter the number, press /.  
Press Talk `.  
To accept the second call and end the active call:  
Press Menu / > End current call & answer.  
To decline the second call:  
To end the second call and make the on-hold call active:  
Press End/Power " and then press Talk `.  
To make the on-hold call active and put the active call on  
hold:  
Press End/Power ". If you subscribe to voicemail,  
the call is forwarded to your voicemail box, unless  
you set Call Forward or If Busy to a different  
number.  
Press Menu / > Swap calls.  
Turn Off Call Waiting  
To turn off Call Waiting before a call:  
Touch *70 before dialing the call. Call Waiting  
is reactivated once the call ends.  
54  
       
forward missed calls to different numbers depending  
on the reason you missed the call.  
Making a Three-Way Call  
With Three-Way Calling, you can talk to two people at  
the same time. When using this feature, the normal  
airtime rates will be charged for each of the two calls.  
Forwarding All Calls  
When you set your phone to forward all calls, an icon  
appears in the top row of the display:  
1. During an active phone call, press Menu / > Add  
call. (The first call is placed on hold.)  
Phone line 1 is active; calls to phone line 1 are  
being forwarded.  
2. Enter a second phone number and press Talk `.  
Phone line 2 is active; calls to phone line 2 are  
being forwarded.  
3. Press Menu / > Merge calls.  
If one of the people you called hangs up during the  
call, you and the remaining caller stay connected. If you  
initiated the call and are the first to hang up, all callers  
are disconnected.  
To forward all calls:  
1. Touch  
>
Settings > Call settings >  
Call forwarding.  
2. Touch Always forward.  
Call Forwarding  
If you specified a forwarding number for this type  
of call before, this number displays. To forward all  
calls to this number touch Enable.  
Call Forwarding lets you forward all your incoming calls  
to another phone number – even when your phone is  
turned off. You can continue to make calls from your  
phone when Call Forwarding is activated.  
If no number is specified, touch the number field  
to display the dial pad, enter a phone number  
and touch Done.  
Call Forwarding sends calls to the phone numbers you  
specify. You can forward all calls to one number or  
– or –  
55  
         
Touch the Contacts icon to the right of the  
number field and select a number from Contacts.  
Forward when unanswered — You do not answer on  
the first four rings.  
Forward when unreachable — Your phone is out of  
coverage or powered off.  
3. Touch Enable and press Home X to return to the  
home screen. All your calls are now forwarded to  
the number you specified.  
Note: You are charged a higher rate for calls you have  
forwarded.  
Turning Off Call Forwarding  
To forward missed calls:  
1. Touch  
>
Settings > Call settings >  
Call forwarding.  
1. Touch  
>
Settings > Call settings >  
Call forwarding.  
2. Touch Always forward, Forward when busy, Forward  
when unanswered, or Forward when unreachable.  
Note: If your phone is set to forward all calls, you must first  
disable Always forward to access these options. (See  
3. Touch Disable.  
All your calls are now sent to your phone.  
2. Touch Forward when busy, to specify a forwarding  
number for calls received when your phone is  
busy.  
Forwarding Missed Calls  
Calls you miss are forwarded according to the options  
set for missed calls. By default, missed calls are  
forwarded to voicemail.  
3. If you specified a forwarding number for this type  
of call before, this number displays.  
To forward calls to this number, touch Enable, and  
go to step 6.  
You can specify a forwarding number for each type of  
missed call:  
To delete this number, touch the text field, and  
Forward when busy — Your phone is on a call or  
transferring data.  
DEL  
x
then touch and hold  
.
56  
     
4. To enter a forwarding number:  
non-emergency incidents. If the situation includes  
imminent danger or loss of life, you should dial 911.  
Enter the number and touch Done or touch the  
Contacts icon to the right to select a number from  
Contacts.  
Telecommunications Relay Service  
Nextel supports services for communicating with  
speech and/or hearing impaired individuals. You can  
dial 711 to reach a local Telecommunications Relay  
Center. You will then be connected to your destination  
number. Relay service works through a  
Communications Assistant who reads messages typed  
into a TDD/TTY device by a speech or hearing  
impaired individual to you. The Communications  
Assistant then types your spoken messages to the  
hearing or speech impaired individual.  
5. Touch Enable.  
6. Repeat step 2 through step 5 for Forward when  
unanswered and Forward when unreachable.  
Making International Calls  
Your service default is “International Calls Restricted.”  
Contact Nextel Customer Service to obtain  
international dialing access.  
Telecommunications Relay Service is available 24  
hours a day, seven days a week, and every call is  
strictly confidential.  
Calls placed between the United States and Canada  
do not require an international access code.  
Note: Using 711 to reach Telecommunications Relay Service  
Special Dialing Codes  
may not be available in all areas.  
To enable TTY mode:  
Non-Emergency Numbers  
Nextel supports many “non-emergency” numbers  
(such as #77, 311, and 511) provided by local and state  
governments. These numbers are used to report  
1. Touch  
>
Settings > Call settings >  
Additional call settings > TTY.  
57  
           
2. Select HCO, TTY, or VCO.  
Use different ringer styles so that you can tell which  
line is receiving a call.  
TTY – Type and read text on your TTY device.  
Forward incoming calls to either your primary or  
alternate line phone number.  
VCO (Voice Carry-Over) – Speak into the phone  
and read text replies on your TTY.  
Choose a Second Line Service plan that fits your  
needs.  
HCO (Hearing Carry-Over) – Type text on your  
TTY and listen to voice replies on your phone.  
In order to activate Second Line Service, contact your  
Nextel Sales Representative or call Nextel Customer  
Service.  
Nextel Phone Services  
Contact Nextel Customer Service to obtain these  
services or for additional information.  
To set the active line (primary or alternate):  
1. Press Menu / > Settings > Call settings >  
Phone line.  
Note: Some services are not available outside of the  
continental United States.  
2. Select a phone line to be active.  
When incoming calls are made to a non-active line,  
they will be sent to voicemail without ringing. (See “Call  
Second Line Service  
You can have two different phone numbers on the  
same phone. With Second Line Service, you can:  
Get separate bills for each phone line.  
Bring in an existing wireless or home phone number  
to Nextel to activate on the second line.  
Have two different area codes (must be in same  
market) to convey a local image to callers.  
58  
 
Sprint 411  
Dial 411 from your wireless phone to receive  
nationwide listings, movie listings and showtimes,  
restaurant reservations, and driving directions, as well  
as sports scores, stock quotes, and weather conditions.  
Spanish speaking operators available. Receive up to  
three phone numbers or pieces of information per call,  
and be automatically connected at no additional  
charge. Airtime and other charges apply.  
59  
To launch the browser:  
Touch  
>
Browser.  
5. Web and Data Services  
Connection  
Mobile Network:  
Wi-Fi:  
Web Address  
To go to a URL, touch  
Go on the keyboard.  
Links  
Touch to open.  
Drag or flick to scroll.  
Image Search  
Web Browser  
Touch  
to open a menu  
where you can open your  
bookmarks and more.  
With Web access on your phone, you can browse your  
favorite websites, making it easier than ever to stay  
informed while on the go. Follow sports scores,  
breaking news, and weather, and shop on your phone  
anywhere on the Nextel National Network.  
Back  
Reload  
Forward  
Tools  
Tabs  
Note: If you can’t connect, contact your service provider.  
60  
         
Connect  
Browser Options  
Your phone uses the data capabilities of the Nextel  
National Network (over the air) to automatically connect  
to the Web. For an even faster Web experience, you  
can also set your phone to use available Wi-Fi  
networks. (See “Wi-Fi®” on page 66 for details on  
setting up and using Wi-Fi connections.)  
Touch  
Tools to see browser options:  
Options  
Bookmarks  
Add, delete and manage  
bookmarks.  
History  
View and clear your browser’s  
history.  
Tip: Contact Nextel for information on data usage fees and  
your service agreement.  
Start Page  
Takes you to your browser’s start  
page.  
Select Web Links  
Saved Pages  
Downloads  
Settings  
Save Web pages.  
When you touch a link, your  
phone outlines it and goes to  
that page. If you touch and  
hold the link, your phone  
shows options, such as Open  
in new tab.  
View your downloads.  
Open your browser’s settings  
menu.  
Find in Page  
Help  
Search Web pages for words or  
phrases.  
Open your browser’s help menu.  
61  
 
Going to a Specific Website  
Note: Bookmarking a page does not store the page contents,  
just its address.  
To go to a particular website by entering a Web address  
(URL):  
Some pages cannot be bookmarked. Whether a  
particular Web page may be marked is controlled by its  
creator.  
1. Touch the text entry field at the top of the page.  
If the text entry field is not visible, press Menu / to  
bring it up.  
Accessing a Bookmark  
2. Enter a Web address and then touch Go in the  
lower right corner of the keyboard.  
1. Touch  
Tools > Bookmarks.  
2. Touch a bookmark to open the Web page.  
Note: Not all websites are viewable on your phone.  
Reloading a Web Page  
Creating a Bookmark  
Touch  
Reload at the bottom of the screen.  
Bookmarks allow you to store the address of your  
favorite websites for easy access at a later time.  
(The browser will reload the current Web page.)  
1. Go to a Web page and touch  
Bookmarks.  
Tools >  
2. Touch Add (website name).  
3. Confirm or edit the bookmark title, choose a folder  
to store it in, and then touch Add at the bottom of  
the screen.  
62  
           
selecting Install, the app will download. After  
selecting Buy, you may be asked to sign in to an  
additional Google account. Sign in and select  
Purchase now to proceed. Follow the onscreen  
instructions. To see the download progress, open  
the notifications window.  
Downloading Apps  
Android Market™  
Touch  
>
Market  
The Android Market™ lets you access all the fun games  
and cool apps you want. It provides you with access  
software developers everywhere, so you can find the  
app you want. If you need help or have questions  
about Android Market, press Menu / > Help from any  
market screen.  
After you download an app, the icon for that app  
appears on your Applications tab (see “Apps  
Manage Apps  
1. To manage your apps, from your phone’s home  
screen touch  
>
Settings > Applications >  
Note: You’ll need a Gmail account in order to buy and  
download apps from Android Market. (See “Gmail” on  
page 64.)  
Manage applications.  
2. Touch an app to open the details screen — from  
here you can review, uninstall, and more.  
Browse and Install Apps  
Restore Apps  
From the Market home page, select a category or  
search for an app, touch the app you want to  
install, and then touch Install (if the app is free)  
or Buy.  
To reinstall any downloaded items, touch  
>
Market > My Downloads. All previously installed  
apps are listed and available for download.  
If an app you are downloading requires access to  
your data or control of functions on your phone,  
you’ll be asked to give your permission. After  
63  
       
To control email notifications:  
Press Menu / > Settings > Email notifications.  
To apply a label to a thread:  
Email  
Gmail  
Touch and hold a message, and then touch  
Change labels.  
Set up a Gmail Account  
If you did not set up a Gmail account when you ran  
through the setup wizard (see page 9), you can set it  
up now.  
POP/IMAP Email  
Set Up an Account  
Touch  
>
Gmail and follow the onscreen  
Touch  
>
Email.  
instructions.  
The email setup wizard will guide you through setting  
up your email account.  
Create a New Email  
1. Touch  
>
Gmail > Menu / > Compose.  
Create a New Email  
2. Enter the recipient email address and message,  
and then touch Send.  
1. Touch  
>
Email > Menu / > Compose.  
2. Enter the recipient email address and message,  
and then touch Send.  
Tip: Press Menu / for options, such as Attach or  
Add Cc/Bcc.  
Tip: Press Menu / for options, such as Attach or Add Cc/  
Gmail Features  
To search for email:  
Bcc.  
Press Menu / > Search in a messages list.  
64  
       
Google Data Synchronization  
Microsoft™ Office Outlook™  
Synchronization  
The Google apps on your phone give you access to  
the same personal information (emails, events, and  
contacts) that you have on a computer using Gmail,  
Calendar, and Contacts. It’s easy to synchronize the  
Google apps information you want to keep up-to-date.  
What Can You Manage?  
Email, contacts, and calendar on your phone give you  
access to the same personal information that you add,  
view, and edit on your computer with the use of  
Microsoft™ Outlook™.  
Touch  
>
Settings >  
Data synchronization > Google.  
You can:  
Select Apps to Synchronize  
View Google™ and Exchange contacts in one list.  
Schedule and respond to meeting requests.  
Access your company directory.  
1. Touch Background data to enable synchronization.  
Tip: To save battery power do not touch Background data.  
2. Touch the apps you want to synchronize (Gmail,  
Calendar, or Contacts).  
Set Up Synchronization  
1. Touch  
>
Settings >  
Data synchronization > Exchange ActiveSync.  
2. Enter your user name ([email protected]),  
password, email address, and server details  
including domain name and security type. (The  
server address is the same URL you use to access  
65  
   
Wi-Fi®  
your company’s email using the Web on your  
computer.)  
Use a wireless network for fast Internet access and to  
download data.  
Tip: Contact your business IT department for server details.  
3. Touch Next.  
Wi-Fi settings  
4. Set up your sync options: select email and/or  
contacts.  
Touch to turn on & scan.  
Wi-Fi  
5. Touch Save & sync.  
Network notification  
Notify me when an open network is  
available  
Note: Set data synchronization to manual to extend battery  
Wi-Fi networks  
Your network  
Touch to connect.  
Corporate Calendar  
Touch  
>
Calendar.  
Add Wi-Fi network  
Corporate calendar appointments are shown in the  
same calendar as your Gmail calendar appointments,  
but each will be shown in a different color. Once you  
have configured your corporate account, you can start  
the calendar app to view, add, and manage your  
corporate calendar appointments.  
Turn Wi-Fi On or Off  
Touch  
>
Settings > Wireless controls >  
Wi-Fi.  
Tip: To extend battery life, turn off Wi-Fi power when not in  
use.  
Tip: To see the color codes for your calendar press  
Menu / > More > My calendars.  
66  
   
Wi-Fi Search and Connect  
To find networks in your range:  
1. Touch  
Wi-Fi settings.  
>
Settings > Wireless controls >  
2. Touch Wi-Fi to turn on and scan. If Wi-Fi is already  
on, press Menu / > Scan. Your phone lists the  
networks it finds within range.  
3. To see your phone’s MAC address or other Wi-Fi  
details, press Menu / > Advanced.  
4. Touch a network to connect.  
5. If necessary, enter Network SSID, Security, and  
Wireless password, and touch Connect. When your  
phone is connected to a Wi-Fi network, the  
wireless indicator  
appears in the status bar.  
Tip: When you are in range and Wi-Fi is on, you will  
automatically reconnect to available networks you’ve  
connected to before.  
67  
 
Sound Settings  
Ringtones  
6. Settings  
Your phone provides a variety of ringer options that  
allow you to customize your ring and volume settings.  
These options allow you to identify incoming calls and  
messages by the ring.  
Selecting Ringtones  
To personalize your ringtones:  
1. Touch  
>
Settings > Sound & display >  
Phone ringtone or Notification ringtone.  
Personalize  
2. Touch a ringtone to select it, and touch OK to  
assign it. (To preview a ringtone, touch it or use the  
Navigation Key to scroll through and hear  
samples.)  
Display Language  
You can choose to display your phone’s onscreen  
menus in one of several languages.  
Assigning a Ringtone to a Contact  
You can also assign a ringer to a specific contact entry  
so you know who's calling without looking at the  
phone.  
1. Touch  
Select locale.  
>
Settings > Locale & text >  
2. Touch a language to select it.  
1. Touch  
Contacts.  
68  
           
   
Silent Mode  
Display Settings  
The Silent Mode option allows you to mute all sounds  
without turning your phone off.  
Changing the Screen Timeout  
Select how long the display screen remains backlit  
after any screen touch or keypress is made.  
To activate and deactivate Silent Mode:  
Press and hold End/Power " to open the Phone  
Options menu and touch Silent mode.  
Touch  
>
Settings > Sound & display >  
Screen timeout and then touch a duration.  
Note: Long backlight settings reduce the battery’s talk and  
Adjusting the Phone’s Volume Settings  
standby times.  
Adjust your phone’s volume settings to suit your needs  
and your environment.  
Changing the Wallpaper  
Choose what you see on the display screen while  
powering on or off and while on the home screen.  
1. Touch  
>
Settings > Sound & display.  
2. Select Ringer volume or Media volume.  
From the home screen, press Menu / >  
3. Choose a volume level and touch OK.  
Wallpaper > Wallpaper gallery or Media Gallery.  
Tip: You can adjust the ringer volume while on the home  
screen (or the earpiece volume during a call) by using  
the Volume button on the left side of your phone.  
To select a wallpaper from the Wallpaper gallery:  
1. Flick the thumbnail images left or right to select a  
wallpaper.  
2. Touch Set wallpaper to assign an image.  
70  
         
To select a wallpaper from Media Gallery:  
1. Touch Media Gallery.  
Messaging Settings  
Staying connected to your friends and family has never  
been easier. With your phone’s advanced messaging  
capabilities, you can send and receive many different  
kinds of text messages without placing a voice call.  
(For more information see “Multimedia Messages  
2. Touch an image to open it.  
3. Crop the picture if prompted, and then touch Save  
to set the image as your wallpaper.  
Tip: You can also set an image as a wallpaper from within  
Media Gallery by touching and holding the image  
thumbnail and then touching Set as > Wallpaper.  
Messaging settings make messaging easier by letting  
you decide how you would like to be notified of new  
messages, create a signature with each sent message,  
and create your own preset messages.  
Changing the Clock Display  
Select a format for the time and date display.  
Touch  
>
Settings > Date & time.  
Setting Message Notification  
Touch Use 24-hour format to toggle between  
24-hour time display and 12-hour time display.  
When you receive a message, your phone notifies you  
by displaying an icon in the notification bar. You can  
also choose to be notified with a sound while making a  
phone call.  
Touch Select date format, and then touch a date  
format to assign it.  
Note: The time, time zone, and date are set by the network,  
and even though they show up as options, they cannot  
be changed.  
To turn messaging notifications on and off:  
Touch  
>
Messaging > Menu / >  
Settings > Notifications.  
71  
           
To select a message notification ringtone:  
Touch Messaging > Menu / >  
Airplane Mode  
>
Settings > Select ringtone, touch a ringtone to  
select it, and then touch OK.  
Sometimes you may want to have your phone on, but  
turn off its ability to make and receive calls and other  
transmissions.  
To set your phone to vibrate when you receive a message:  
Touch Messaging > Menu / >  
Settings > Vibrate.  
To set your phone so that it cannot make or receive phone  
calls, Direct Connect calls, Group Connect calls, Talkgroup  
calls, or transfer data:  
>
Setting Reports  
You can also choose to receive read and delivery  
reports for each message you send.  
Press and hold End/Power " to open the Phone  
Options menu and touch Airplane mode.  
When in Airplane Mode,  
notifications bar.  
appears in your  
To receive read reports:  
To turn Airplane Mode off:  
Touch  
>
Messaging > Menu / >  
Press and hold End/Power " to open the Phone  
Options menu and touch Airplane mode.  
Settings > Read reports.  
To receive delivery reports:  
Touch Messaging > Menu / >  
Note: When Airplane Mode is on, your phone’s Bluetooth  
capability is disabled, and all active Bluetooth  
connections are dropped.  
>
Settings > Delivery reports.  
72  
         
To access the Direct Connect settings menu:  
Touch Settings > Call Settings >  
Call Settings  
>
Direct Connect settings.  
Setting Prepend Dialing  
The Prepend feature lets you set a prefix to be added to  
the beginning of all dialed numbers, such as a country  
code for international calls.  
Resume DC — adds 30 seconds to the DC timeout  
so Direct Connect calls do not time out quickly  
while you are multitasking.  
One Touch DC — sets One Touch DC.  
1. Touch  
>
Settings > Call settings >  
Sharing contact info — sets info to share.  
Additional call settings.  
Talkgroup — lets you silence Talkgroups, define  
your Talkgroup area, and manage your Talkgroup  
areas.  
2. Touch Prepend to activate this feature, and then  
touch Prefix number.  
DC button light — controls whether or not the  
backlight displays when using Direct Connect.  
3. Touch the text field to display the keypad, enter a  
prefix in the text field (such as +1 for international  
calls), and then touch OK.  
Setting One Touch DC  
Note: This setting does not apply to 911 or Sprint 411.  
One Touch DC sets your phone to call the most recent  
Direct Connect number or Group on the Call log list, or  
a Direct Connect number you choose, every time you  
press the DC button. You can also set your phone to  
bring up a Direct connect Contacts list when the DC  
button is pressed.  
Direct Connect Settings  
The Direct Connect settings menu controls how your  
phone handles Direct Connect calls, Group Connect  
calls, and Talkgroup calls.  
73  
           
1. Touch  
>
Settings > Call settings >  
SIM Card Security  
Direct Connect settings > One Touch DC.  
Important: Except for making emergency calls, your phone  
2. Select Off, Launch DC Contact List, DC a selected  
contact, or DC the most recent number, and then  
touch OK.  
does not function without the SIM card.  
SIM Card’s PIN  
Tip: If you are entering a Talkgroup number, enter # before  
You can protect access to your phone by using the SIM  
card’s PIN (Personal Identification Number). When you  
enable SIM PIN, you must enter the PIN each time you  
power up the phone. You can change or disable the  
SIM PIN.  
the number.  
Security Settings  
Touch  
>
Settings > Security & location.  
Lock Your SIM Card  
1:22 PM  
1. Touch  
>
Settings > Security & location >  
Security & location  
Locate to street-level (requires more  
battery plus view of sky)  
Set up SIM card lock > Lock SIM card.  
Compass  
2. Touch the SIM PIN field to display the keyboard,  
and then enter your SIM PIN code.  
Calibrate Compass  
Calibrate the compass for optimum  
performance  
Security  
Important: The default SIM PIN is 0000. Change your PIN to  
Security lock  
SIM card lock  
prevent fraudulent use of the SIM card.  
Set up SIM card lock  
Passwords  
3. Touch OK.  
Visible passwords  
Show password as you type  
74  
         
Entering the PIN  
Unblocking the PIN  
1. Press and hold End/Power " to turn on your  
If you enter your PIN incorrectly three times, your SIM  
card is blocked. To unblock your SIM card, you must  
contact Nextel Customer Service to get a PIN Unblock  
Code (PUK). Follow their instructions for unblocking  
your SIM PIN.  
phone.  
2. When the SIM PIN is locked screen appears, press  
Menu /, enter your SIM PIN, and touch OK.  
Important: If you enter your PIN incorrectly three times, your  
SIM card is blocked. See “Unblocking the PIN” on  
page 75.  
Important: If you unsuccessfully enter the PUK code ten  
times, your SIM card is permanently blocked and  
must be replaced. If this happens, you get a  
message to contact Nextel Customer Service.  
Except for making emergency calls, your phone  
does not function with a blocked SIM card.  
Changing the PIN  
Note: SIM PIN must be turned on in order to access this  
feature.  
Your Phone’s Lock Feature  
1. Touch  
>
Settings > Security & location >  
Set up SIM card lock > Change SIM PIN.  
2. Enter the current SIM PIN and touch OK.  
3. Enter the new SIM PIN and touch OK.  
Screen Lock  
Note: You can make emergency calls on a locked phone  
4. Reenter the new SIM PIN to confirm and then  
To lock the screen:  
touch OK.  
Press Screen Lock # on the top of the phone.  
Tip: To enter the previous and new SIM PINs, you must first  
– or –  
touch the SIM PIN field to display the keyboard.  
75  
     
Let the screen time out (don’t press or touch  
anything).  
Unlocking Your Phone  
At the “Enter password to unlock” prompt, enter  
To unlock the screen:  
your password and touch Enter.  
Stretch to unlock  
Press Screen Lock # and then drag  
right.  
to the  
– or –  
At the “Draw pattern to unlock” prompt, draw the  
saved pattern to unlock the phone.  
Security Lock  
Calling in Lock Mode  
To access the Security lock menu:  
You can place calls to 911 when in lock mode.  
Touch  
>
Settings > Security & location >  
Security lock, and then select an option.  
Touch the Emergency call button at the bottom of  
To set a password or an unlock pattern that you  
need to draw to unlock your screen, touch  
Security lock type > Password or Pattern and  
follow the prompts to enter and confirm a  
password or pattern.  
the screen, dial 911, and press Talk `.  
Resetting Your Phone  
Phone Reset  
To turn the lock off, touch Security lock type >  
None and enter the password or pattern as  
prompted.  
Selecting Reset phone resets all phone settings back to  
their default values, and clears all information (text  
messages, contacts, emails, etc.) and downloaded  
apps.  
To change the password or lock pattern, touch  
Change unlock password or Change unlock  
pattern. (To select either of these options, a  
security lock type must be set.)  
1. Touch  
>
Settings > SD card & phone  
storage > Master Clear > Reset phone.  
76  
       
2. Enter your phone’s six-digit security code and  
touch OK. (A disclaimer is displayed.)  
Note: Your security code is a six-digit number used for  
resetting your phone. Please contact Nextel Customer  
Service if you do not know your security code.  
3. Read the prompt and touch Erase everything to  
complete the reset. (Press Back % to cancel.)  
Feature Reset  
Selecting Feature Reset resets all phone settings back  
to their default settings.  
1. Touch  
>
Settings > SD card & phone  
storage > Feature Reset > Feature Reset.  
2. Enter your phone’s six-digit security code and  
touch OK. (A disclaimer is displayed.)  
Note: Your security code is a six-digit number used for  
resetting your phone. Please contact Nextel Customer  
Service if you do not know your security code.  
3. Read the prompt and touch Re-apply All to  
complete the reset. (Press Back % to cancel.)  
77  
Note: The Call log list records only calls that occur while the  
phone is turned on. If a call is received while your  
phone is turned off, it will not be included in the phone’s  
Call log list.  
7. Call Log  
If you return a call from the voicemail menu, it will not be  
included in your phone’s Call log list.  
Calls and Call Alerts  
If the number of a recent call is stored in Contacts, the  
following information appears:  
The name assigned to the number.  
The Contacts type associated with the number.  
About the Call Log  
The Direct Connect number Contacts type appears  
when you receive a Direct Connect call or Call Alert,  
even if the number is not stored in Contacts.  
The Call log list displays the numbers (or Contacts  
entries) for phone calls and Direct Connect calls you  
placed, accepted, or missed, and for Call Alerts you  
have received. It also displays My Info and contact  
information sent to you from other phones. It is  
continually updated as new numbers are added to the  
beginning of the list.  
Call Alerts you have received appear as Direct Connect  
calls. Like all items in the Call log list, they remain listed  
until you delete them.  
78  
         
For phone calls, an icon appears giving information  
about the call.  
If you receive My Info from the same phone more than  
once, only the most recently sent version appears in  
the Call log list.  
A call you made.  
Contact Information From Other Phones  
A call you received.  
The Call log list displays contact information sent from  
other phones. This information comes from the other  
phone’s Contacts list or Call log list. See “Sending My  
A missed call. Missed calls appear on the Call log  
list only if you have Caller ID.  
When you select a call to view its details, you see  
information such as the name associated with the call,  
the number, date, time, and duration of the call.  
This icon  
appears with contact information on the  
Call log list.  
Contact information in the Call log list displays:  
My Info From Other Phones  
The name contained in the contact information.  
The Call log list displays My Info sent from other  
The Contacts type associated with the number or  
address contained in the contact information.  
The name or Direct Connect number of the person  
who sent the contact information appears as a  
separate item on the Call log list, above the information  
sent. If one person sends you more than one item of  
contact information, all the items appear below the  
person’s name or Direct Connect number.  
This icon  
appears with My Info sent from other  
phones, along with the Direct Connect number of the  
person who sent the information.  
When you select My Info from other phones to view its  
details, you see all the information sent.  
79  
 
When you select contact information to view its details,  
you see the name or Direct Connect number of the  
person who sent the information and all the information  
in the item.  
Saving Items From the Call Log  
1. From Call log, touch an entry to open it.  
2. Touch Add to contacts.  
If you receive contact information with the same name  
from the same phone more than once, only the most  
recently sent version appears in the Call log list.  
Tip: If the item you are storing is a call, Add to contacts does  
not appear if the number is already stored in Contacts.  
3. Touch Create new contact to store the number in a  
new Contacts entry, or touch an entry to store the  
number to an existing entry.  
Viewing the Call Log  
Touch  
Dialer > Call log.  
Note: Storing My Info or contact information from another  
phone to an existing Contacts entry does not change  
its name.  
Tip: When you’re in the home screen, you can press Talk `  
to go to the Call log.  
To view the details of an item on the list:  
4. If the item is a call, you must assign a Contacts  
type to the number.  
Touch an entry.  
Touch the Contacts type label next to the number  
and touch a Contacts type from the list.  
5. To add more information to the entry (optional),  
follow the applicable instructions in “Creating  
6. Scroll to the bottom of the entry and touch Done.  
80  
     
Deleting Items From the Call Log  
To delete an item from the Call log list:  
1. From the Call log, touch an entry to open it.  
2. Press Menu / > Delete from call log.  
To delete all items on the Call log list:  
Touch  
Dialer > Call log > Menu / >  
Delete all.  
Prepending a Number From the  
Call Log  
If you need to make a call from the Call log list and you  
are outside your local area code, you can add the  
appropriate prefix by prepending the number.  
1. Touch and hold a Call log entry and then touch  
Edit number before call > Menu / > Add prefix.  
2. Enter the prefix and touch OK to call the number.  
81  
         
About Contacts  
8. Contacts  
Each Contacts entry can store several numbers, email  
addresses, chat addresses, or street addresses.  
Information stored in Contacts is saved in your phone’s  
memory.  
Tip: You can import Contacts information from and export it to  
page 88 for details.  
A Contacts entry contains:  
A name — Typically, this is the name of the person  
whose contact information is stored in the entry.  
A ringtone — You can assign a ringtone to each  
entry. This is the sound your phone makes when you  
receive phone calls or call alerts from any of the  
numbers stored in the entry.  
A Contacts type — Each number or address stored  
must be assigned a Contacts type. (See “Types of  
82  
       
Types of Contacts  
Each number or address stored must be assigned a  
Contacts type:  
Creating Contacts Entries  
Tip: ICE – In Case of Emergency  
To make it easier for emergency personnel to identify  
important contacts, you can list your local emergency  
contacts under “ICE” in your phone’s Contacts list. For  
example, if your mother is your primary emergency  
contact, list her as “ICE–Mom” in your Contacts list. To list  
more than one emergency contact, use “ICE1–___,”  
“ICE2–___,” etc.  
Contacts Type  
Entry Types  
Phone numbers  
Home, Mobile, Work, Fax, Work  
2, Pager, Other, Custom  
DC1, DC2, Custom  
Direct Connect  
Email addresses  
Chat addresses  
Home, Work, Other, Custom  
A number or address and a Contacts type, or a name  
are required for all Contacts entries. Other information  
is optional. You may enter the information in any order.  
AIM, Windows Live, Yahoo,  
Skype, QQ, Google Talk, ICQ,  
Jabber  
After you have entered the number or address,  
Contacts type, and any other optional information,  
scroll to the bottom of the entry and touch Done to save  
the entry to Contacts.  
Postal addresses Home, Work, Other, Custom  
Work, Other, Custom  
Organizations  
To cancel a Contacts entry at any time touch Revert.  
To create a Contacts entry:  
1. Touch  
Contacts > Menu / > New contact.  
83  
           
2. To assign a name to the entry, touch the name  
To assign a Contacts type for each number or  
address (such as Mobile, Home, Work, etc.),  
touch the label next to the entry field and touch a  
Contacts type to assign it.  
field, enter a name and touch Next.  
1:22 PM  
New contact  
4. To add more numbers or addresses to the entry:  
First and Last  
Touch  
to add a new entry field for the type of  
contact you are creating (Phone numbers, Direct  
Connect, Email addresses, etc.)  
Touch + to add another  
entry.  
Phone numbers  
Mobile  
Phone number  
5. To assign a ringtone to the name (optional):  
Touch Ringtone, select a ringtone and then  
Touch - to remove this  
entry.  
Push to Talk  
PTT1  
touch OK.  
PTT number  
Touch to display label  
options.  
6. To assign a picture to the name (optional):  
Touch the picture icon to the left of the name field,  
touch a picture to select it, crop the picture if  
prompted, and then touch Save.  
Email addreses  
Home Email address  
7. Scroll to the bottom of the entry and touch Done.  
3. To add a number or address:  
Touch the entry field.  
Creating Pauses and Waits  
When storing a number, you can program your phone  
to pause or wait between digits while dialing. A pause  
makes your phone pause for three seconds before  
Enter the number or address. For phone  
numbers, use the ten-digit format. For Direct  
Connect numbers, be sure to include the  
asterisks (*).  
84  
   
dialing further. A wait makes your phone wait for your  
response before dialing further.  
1:22 PM  
This feature is useful when using voicemail or other  
automated phone systems that require you to dial a  
phone number and then enter an access number.  
Dialer  
Call log  
Contacts  
Favorites  
All contacts  
Search  
Touch to search  
contacts.  
Search contacts  
To enter a pause or a wait:  
Me  
My Info  
Your details–always  
first in the list.  
1. Touch the entry field to bring up the keypad and  
begin entering the phone number.  
Home  
PTT  
Ashley Grover  
Bomi Kim  
2. When you want to insert a pause or a wait, touch  
the Symbol Key (&) in the lower left-hand corner  
of the keypad.  
Contacts List  
Touch to view  
contact information.  
Touch & hold to edit,  
delete, and more.  
Mobile  
PTT 1  
Book Club  
3 Members  
PTT 1  
3. Touch Pause or Wait.  
Menu Options  
Press Menu  
create, filter, and  
sync contacts.  
Note: You can have multiple pauses in a phone number and  
Chris Boomer  
to  
combine waits and pauses.  
Viewing Contacts  
2. Touch the contact name to display the entry, and  
then scroll up or down to view all information  
stored for the entry.  
1. Touch  
Contacts and then either scroll  
through the contacts list, or touch Search contacts  
and enter a name. (Your phone finds the name  
you entered or the nearest match.)  
85  
   
Filtering Contacts Entries  
You can set Contacts to display only entries with  
certain attributes.  
Adding a Number to an Entry  
1. Touch  
Contacts and touch an entry.  
2. Press Menu / > Edit contact.  
1. Touch  
Contacts > Menu / > Filter.  
3. Scroll to the contact type for the entry and touch  
2. Touch All contacts, Contacts with phone numbers,  
Contacts with DC numbers, Phone contacts, Google  
All Contacts, or Google My Contacts and then  
touch OK.  
to create a new entry field.  
4. Select an entry type for the new entry, and enter  
the number.  
5. Scroll to the bottom of the entry and touch Done to  
save the new number.  
Contacts Action Options  
To quickly access these actions for a saved Contact:  
Editing Entries  
1. Touch  
Contacts.  
2. Touch and hold a contact to display a quick list of  
action items, such as View contact, Call Mobile,  
Send text message, Direct Connect, and Share  
via DC.  
1. Touch  
Contacts and touch an entry.  
2. Press Menu / > Edit contact.  
3. Follow the applicable instructions in “Creating  
Contacts Entries” on page 83 to edit the entry.  
3. Touch an option to take the corresponding action.  
4. Scroll to the bottom of the entry and touch Done  
when you have finished making your changes.  
86  
     
2. Press Menu / > Edit contact.  
Deleting Entries  
3. Touch Ringtone.  
1. Touch  
Contacts and touch an entry.  
4. Scroll through available ringtones. (Touch a  
ringtone to hear a sample.)  
2. Press Menu / > Delete contact.  
3. Touch OK to confirm.  
5. Touch a ringtone to select it.  
6. Touch OK to save the assigned ringer.  
7. Scroll to the bottom of the entry and touch Done.  
Deleting a Number or Address  
1. Touch  
Contacts and touch an entry.  
2. Press Menu / > Edit contact.  
Assigning a Picture to an Entry  
3. Scroll to the number or address you want to delete,  
Assign a picture to display when you receive a call  
from an entry.  
and touch  
to the right of the item to remove it  
4. Scroll to the bottom of the entry and touch Done.  
1. Touch  
Contacts and touch an entry.  
Note: If an entry contains only one number or address,  
2. Press Menu / > Edit contact.  
deleting the number or address deletes the entry.  
3. Touch the picture icon to the left of the name field.  
Selecting a Ringtone for an Entry  
4. Scroll through available pictures and touch one to  
select it.  
Assign a ringtone to a Contacts entry so you can  
identify the caller by the ringtone. (See “Ringtones” on  
If prompted, crop or resize the picture.  
5. Touch Save.  
6. Scroll to the bottom of the entry and touch Done.  
1. Touch  
Contacts and touch an entry.  
87  
         
Export Contacts to Your SIM Card  
Import and Export Contacts  
Touch  
Contacts > Menu / >  
Your phone stores its contact entries in its internal  
memory and not within your SIM card. The first time  
you use your phone, you will need to import the  
contacts from your SIM card to your phone for you to  
be able to use the contacts stored on the SIM card.  
SIM Manager > Export contacts to SIM.  
The contacts stored on your phone will not be saved  
on your SIM card unless you export your contacts. It is  
recommended that you export your contacts to your  
SIM card from time to time to keep your phone and  
SIM card in sync.  
Note: Your SIM card can store only basic information, such as  
phone numbers, Direct Connect numbers, Group  
Connect numbers, Talkgroup numbers, and email  
addresses.  
Import Contacts From Your SIM Card  
Touch  
Contacts > Menu / >  
SIM Manager > Import contacts from SIM card.  
Note: You might have already done this during “Setup  
88  
     
View your calendar in  
different ways: Press  
Menu / > Agenda, Day,  
Week or Month. When you  
highlight an event in the day  
and week views, more  
details appear.  
1:22 PM  
January, 2009  
Sun Mon Tue Wed Thu Fri Sat  
9. Tools  
28  
4
29  
5
30  
6
31  
7
1
8
2
9
3
10  
Add Calendar Events  
11  
18  
25  
12  
19  
26  
13  
20  
27  
14 15 16 17  
21 22 23 24  
28 29 30 31  
From any calendar  
view, press Menu / >  
New event. Enter event  
details and then scroll  
to the bottom of the  
entry and touch Save.  
Calendar  
Touch  
>
Calendar  
Manage Calendar Events  
Tip: You can send calendar events to other people using  
Direct Connect. (See“Nextel Direct Send” on page 37.)  
To edit an event, touch and hold the event,  
touch Edit event, edit the event details, and then  
scroll to the bottom of the entry and touch Save.  
89  
     
Google Maps™ opens in “Map mode”. To learn more  
about the different map modes, see “Select Map  
Google Maps™  
Note: This feature is not available in all areas. Check with  
Nextel for coverage availability.  
Set Your Location Sources  
To launch the Google Maps tool, touch  
>
Set your phone to determine your location using GPS  
satellite signals (highly accurate, but uses battery  
power) or using the mobile network (less accurate, but  
conserves battery power).  
Google Maps.  
1:22 PM  
To set your location source(s), touch  
>
Settings > Security & location > Enable GPS  
satellites and/or Use wireless networks.  
Map View  
Drag or flick to scroll.  
Find Your Location  
Note: Don’t forget to set your location sources.  
Touch  
>
Google Maps, and then press  
Menu / > My Location. Your location shows on  
the map as . The bigger the circle, the less  
accurate the location.  
Press Menu  
to open a  
menu where you can search,  
show your location, change  
map modes, get directions,  
and more.  
Map mode  
More  
Search  
Directions  
Find Any Location  
My location  
Join latitude  
1. Press Menu / > Search.  
90  
 
2. Enter text in the search box, (for example, an  
address, business, or city), and then touch  
5. When you have finished, press Menu / > More >  
Clear map.  
.
Tip: If it is an address you have visited before, select from the  
Select Map Mode  
list shown.  
Touch  
>
Google Maps, and then press  
3. Touch the search box, in the lower left-hand  
corner, to view all the results, and then touch the  
one you want. Select Show on map, Get directions,  
Street view, Call or Add as a contact.  
Menu / > Map mode to select from Map (standard  
map view), Satellite (map with photos), or Traffic  
(map with traffic conditions).  
Press Menu / > More > Clear Map to clear your  
selections.  
Get Directions  
1. Touch  
>
Google Maps, and then press  
Latitude  
Menu / > Directions.  
Note: This feature is not available in all areas. Check with your  
2. Enter a starting point address, or touch  
and  
service provider.  
select My current location, Contacts, or Points on  
map.  
Join Latitude  
3. Enter an end point address, or touch  
and select  
See where your friends and family are on Google  
Maps™. Plan to meet up, check that your parents got  
home safely, or just stay in touch.  
Contacts or Points on map.  
4. Select your mode of transport (car, public transport  
or walk), then touch Go. Your directions are shown  
as a list. To view your directions on a map, press  
Menu / > Show on map.  
Don’t worry, your location is not shared unless you  
agree to it. You need to join Latitude, and then invite  
your friends to view your location or accept their  
invitations.  
91  
   
To join Latitude:  
Touch  
Share Location  
>
Google Maps > Menu / > Join  
When you receive a request to share location details  
you can choose to:  
Latitude. Read the privacy policy and if you agree  
with it, touch Allow & Share.  
Accept and share back — see your friend’s location,  
and your friend can see yours.  
Add and Remove Friends  
To add friends:  
Accept, but hide my location — see your friend's  
location, but they can't see yours.  
1. Touch  
>
Google Maps > Menu / >  
Don't accept — location information is not shared  
between you and your friend.  
Latitude > / > Add friends.  
2. Touch Select from Contacts or Add via email  
address, touch a contact, and then touch Add  
friends.  
Hide Your Location  
Touch  
>
Google Maps > Menu / >  
Latitude to show your friends list. Touch your  
contact name, and then press Menu / > Privacy >  
Hide your location.  
If your friends already use Latitude, they’ll receive an  
email request and a notification. If they have not yet  
joined Latitude, they’ll receive an email request that  
invites them to sign in to Latitude with their Google  
account.  
Turn Latitude Off  
1. Touch  
>
Google Maps > Menu / >  
To remove friends:  
Latitude to show your friends list, and then press  
Menu / > Privacy > Turn off Latitude.  
1. Touch  
>
Google Maps > Menu / >  
Latitude to show your friends list, and then touch a  
2. Touch Yes to confirm.  
friend in your list.  
2. Touch Remove.  
92  
From the Google Talk screen, press Menu / and  
select an option to send invitations, add new friends,  
and more.  
Google Talk™  
Google Talk instant messaging lets you chat with other  
Google Talk users on phones or on the web.  
Instant Messages  
To send and receive instant messages, you can use an  
instant messaging app (such as Google Talk™) or your  
browser.  
Touch  
>
Google Talk.  
Touch to change your  
online status message.  
To download and use an instant messaging app,  
touch  
>
Market > Applications >  
Communication, and then choose an app for your  
provider. Once you download the app, you’ll see it on  
page 15.)  
Touch to  
change your  
picture.  
Touch to change  
your status.  
Opened chats.  
Touch a callout  
to open the chat  
screen and start  
chatting with  
If you don’t see an app for your IM provider, you can  
Friends list  
use your Web browser. Touch  
>
Browser,  
your friend.  
and then enter your provider’s Web address and  
touch Go. Once you’re there, follow the link to sign in.  
Your IM options will depend on your IM provider.  
Online  
status:  
Available  
Idle  
Busy  
Offline  
93  
 
Alarm clock  
Touch  
>
Alarm Clock.  
Alarm Clock  
To turn on an alarm, touch  
the check box.  
When an alarm sounds,  
touch Dismiss to turn it off  
or Snooze to delay.  
1:00  
PM  
PM  
To add an alarm, press  
Menu / > Add alarm, and  
then enter alarm details.  
every day  
3:30  
Tue  
4:00  
PM  
Mon, Fri  
To enable or disable an  
alarm, touch the check box.  
Calculator  
Touch  
>
Calculator.  
Your calculator has basic and advanced views. To  
change views, press Menu / > Advanced panel or  
Basic panel. To clear history, press Menu / > Clear  
history.  
94  
     
Inserting the microSD Card  
Note: The memory card provided with your phone contains  
useful preloaded information, including guided tours of  
some of your phone’s features. You may insert another  
compatible memory card at any time; however, any  
information preloaded on the provided memory card  
will not be available.  
10. microSD Card  
1. Remove the battery cover. (See “Installing the  
2. Open the memory card slot cover, and slide in the  
memory card until it clicks into place.  
Using a microSD Card With Your  
Phone  
Using the microSD Card Slot  
Your phone is equipped with a microSD (Secure  
Digital) memory card slot to expand the phone’s  
available memory space. It allows you to store images,  
videos, music, and voice data in your phone.  
Note: You need the memory card installed for some features  
on your phone, such as Camera.  
95  
           
Note: The microSD card and its adapter can be easily  
damaged by improper operation. Please be careful  
when inserting, removing, or handling them.  
 
To insert the microSD card into the microSD adapter:  
Formatting Your Memory Card  
With the label side of the microSD card facing up,  
insert the card into the supplied microSD adapter,  
and gently slide the card until it is fully inserted.  
If you are having difficulty with a memory card, you may  
format the card using your phone. This process  
removes any data on the card and sets up a new folder  
system.  
1. Before you format your memory card you need to  
unmount it. Touch  
>
Settings >  
SD card & phone storage > Unmount SD card.  
2. Touch  
>
Settings >  
SD card & phone storage > Format SD card.  
To remove the microSD card from the microSD adapter:  
WARNING: The formatting procedure erases all the data on  
the microSD card, after which the files CANNOT  
be retrieved. To prevent the loss of important data,  
please check the contents before you format the  
card.  
Hold the front edge of the microSD card, and  
gently pull outward to remove it from the adapter.  
Tip: If your computer has an SD card slot or if you have an SD  
card adapter, you can use the microSD card and adapter  
to transfer files such as audio files, pictures, and videos  
directly between your computer and your microSD card.  
Using the microSD Adapter  
The supplied microSD adapter allows microSD cards  
to be used in SD-compatible devices such as digital  
cameras, printers, and computers. Before using, you  
will need to insert the microSD card into the microSD  
adapter.  
When you insert the card into your computer, select  
Open folder to view files using Windows Explorer (or a  
similar option) and drag and drop files using the available  
folders.  
97  
 
home screen, connect a Motorola micro USB data  
cable from your phone’s micro USB port to a USB  
port on your computer. Your phone should show  
in the notifications bar.  
microSD Settings  
Viewing Memory in the microSD Card  
Note: You may need to remove the USB data cable from the  
1. With the microSD card inserted, touch  
>
charger power head.  
Settings > SD card & phone storage.  
2. The following information will be displayed:  
Total space displays the capacity of the memory  
Note: Make sure to connect the phone to a high power USB  
port. Typically, these are located directly on your  
computer.  
card.  
Available space displays the amount of free  
memory space.  
Note: Your phone supports Microsoft™ Windows™ XP and  
Windows Vista™. Other operating systems may not be  
compatible.  
USB and Memory Card  
2. Your phone shows  
can’t use the files on your memory card while it is  
connected.  
in the notifications bar. You  
USB Drag and Drop  
3. Touch Mount (if asked) to connect your memory  
card.  
You can transfer your pictures,  
videos, music, ringtones, and  
more, from your computer to your  
phone’s memory card.  
Note: If you connect a mass storage device to a peripheral  
device, your device may not work properly.  
1. With a memory card inserted,  
and your phone showing the  
4. On your computer, use the “My Computer” window  
to find “Removable Disk”.  
98  
           
5. Click on the “Removable Disk” icon to access the  
memory card.  
6. Drag and drop your pictures, videos, music,  
ringtones, and more, to your phone folder. To help  
manage your files, you can create more folders in  
your phone folder.  
7. When you’re done, use your computer’s “Safely  
Remove Hardware” feature to finish.  
99  
Touch Gallery on the right to view the picture you  
have just taken.  
11. Camera  
To set the photo as a wallpaper or contact  
photo, touch and hold the thumbnail and then  
touch Set as > Contact icon or Wallpaper.  
To send the photo in a message or post it  
online, touch and hold the thumbnail and then  
select a sharing option. For more info on  
sharing your photos, see “Share Your Photo  
Taking Pictures  
To delete the photo, touch and hold the  
thumbnail and then touch Delete.  
Taking pictures with your phone’s built-in camera is as  
simple as choosing a subject, pointing the lens, and  
pressing a button.  
For more options, press Menu / > More.  
To take a picture:  
1. Press Camera j on the right side of the phone to  
launch the camera.  
2. Aim the camera lens at your subject and press  
Camera j to take a picture.  
To focus the picture, press Camera j half way  
until the auto focus box turns green. To take the  
photo, press Camera j down all the way.  
100  
       
Photo Options  
In the viewfinder, press Menu / > Settings to open the  
Scenes  
Match  
lighting.  
3652  
Scenes  
Effects  
camera menu:  
Effects  
Add  
effects.  
Options  
Picture  
Resolution  
Set the photo resolution.  
Flash  
Turn on  
and off.  
Flash  
Video  
Resolution  
Set the camcorder video  
resolution.  
Gallery  
Go to the  
Media  
Gallery  
Quick Send  
Address  
Store email addresses for sending  
pictures and videos.  
Autofocus Box  
Turns green when  
Picture Counter  
Settings  
Gallery.  
picture is in focus.  
Review Time  
Choose the amount of time a  
recently taken picture is displayed  
on the view screen.  
Tip: Photos are stored on your microSD memory card.  
Picture Resolution is 5MP, unless you change it.  
101  
Manage Your Photos  
View Your Photos  
1. Touch  
>
Media Gallery > All Pictures.  
1:22 PM  
Touch  
Gallery > All Pictures.  
>
Media  
All Pictures  
Today  
2. Touch and hold a photo, then:  
To delete the photo, touch Delete.  
Play a Slideshow  
To set the photo as a contact picture or wallpaper,  
touch Set as.  
Touch  
>
Media  
Gallery > All Pictures >  
Menu / > Play Slideshow to  
start a slideshow. To stop the  
slideshow, touch the display.  
To return to the gallery, press  
Back %.  
Tip: To copy photos to/from a computer, see “USB Drag and  
Edit Your Photos  
1. Touch  
>
Media Gallery > All Pictures.  
Share Your Photo Gallery  
2. Touch and hold a picture, and then touch Edit >  
One-click optimize, Rotate, Crop, Effects, Brightness  
& contrast, Color & saturation, Flip, and Resize.  
To send your photo in a message, Direct Connect call, or  
post it online:  
Using the Zoom  
To adjust the zoom:  
1. Touch  
>
Media Gallery > All Pictures.  
2. Touch and hold a photo, and then touch Share.  
3. Choose how you want to share: DC (Direct  
Connect), Email, Gmail, Messaging, Picasa, or  
Quick Send.  
While in the viewfinder, press the Navigation Key  
down to zoom in, or press up to zoom out.  
102  
   
After you have finished recording your video, touch the  
screen, when prompted:  
Videos  
To send the video in a message or post it online,  
touch Share. For more info on sharing your videos,  
Record and Share Videos  
1. Press Camera j > Menu / > Camcorder.  
To play the video, touch  
.
2. To record the video, press Camera j. To stop the  
video recording, press Camera j again.  
To delete the video, touch Delete.  
Scenes  
Match  
lighting.  
22:59:02  
Scenes  
Effects  
Add  
effects.  
Effects  
Light  
Light  
Turn on  
and off.  
Gallery  
Go to the  
Media  
Gallery  
Gallery.  
Timer  
Settings  
Tip: To send your video in a message, set the video quality to  
Small(QCIF) by pressing / > Settings > Video  
Resolution.  
103  
     
Play Your Videos  
1. Touch  
>
Media Gallery > All Videos.  
2. Touch a video to begin playback.  
00:06  
00:24  
Progress Bar  
Video Controls  
Note: To see the controls while the video is playing, touch the  
display.  
104  
 
Touch  
>
Settings > Wireless controls >  
Bluetooth settings.  
12. Bluetooth® Wireless  
Bluetooth settings  
Touch to turn on & scan.  
Bluetooth  
Device name  
(#########) 38.4 MHz Class 1.5  
Discoverable  
Make device discoverable  
Touch to re-scan.  
Touch to connect.  
Scan for devices  
Turning Bluetooth Power  
On and Off  
Bluetooth devices  
(found device name)  
Pair with this device  
Bluetooth is a short-range communications technology  
that allows you to connect wirelessly to a number of  
Bluetooth devices, such as headsets and hands-free  
car kits, and Bluetooth-enabled handhelds, computers,  
printers, and wireless phones. The Bluetooth  
communication range is usually up to approximately  
30 feet. By default, your device’s Bluetooth feature is  
turned off.  
Note: To extend battery life, turn Bluetooth power off when not  
in use.  
105  
         
Bluetooth Status Indicators  
1. Make sure the device you are pairing with is in  
discoverable mode.  
The Bluetooth status indicators on your phone’s display  
screen shows your Bluetooth connection status at a  
glance:  
Tip: Refer to the guide that came with the device for details.  
2. Touch  
>
Settings > Wireless controls >  
None – Bluetooth is disabled (default status).  
Bluetooth settings.  
– Status indicator will be light blue when Bluetooth  
is turned on, but no device is connected.  
3. Touch Bluetooth to turn on and scan. If Bluetooth is  
already on, touch Scan for devices.  
– Status indicator will turn blue when connected to a  
Bluetooth device.  
4. Touch a device to connect.  
5. If necessary, touch OK, or enter the device passkey  
(for example 0000) to connect to the device. When  
the device is connected, the Bluetooth connected  
Connecting and Disconnecting  
Bluetooth Devices  
indicator  
appears in the notifications bar.  
Note: Using a mobile device or accessory while driving may  
cause distraction and may be illegal. Always obey the  
laws and drive safely.  
Connect New Devices  
Note: This feature requires an optional accessory.  
To connect with a new device, you need to pair with it.  
You only need to do this once for each device; to  
106  
 
Reconnect Devices  
To automatically reconnect your phone with a paired  
device, simply turn on the device.  
To manually reconnect your phone with a paired  
device, touch the device name in the Bluetooth devices  
list.  
Disconnect Devices  
To automatically disconnect your phone from a paired  
device, simply turn off the device.  
To manually disconnect your phone from a paired  
device, touch the device name in the devices list, and  
then touch OK.  
Edit Properties  
To edit your MOTOROLA i1’s device name, touch  
>
Settings > Wireless controls > Bluetooth  
settings > Device name. Enter a name and touch OK.  
107  
     
Music Basics  
13. Music  
Touch  
>
Music, touch a category, and  
then touch a song to begin playing it.  
Music  
Artists  
Songs  
Albums  
Playlists  
Music Artist  
Album Title  
Song Title  
1:14  
3:45  
Categories  
Music Controls  
Touch a category, and  
then touch a song or  
playlist.  
Tip: When a song is playing, you can add it to a playlist by  
pressing / > Add to playlist.  
108  
   
What Music File Formats Can I Play?  
Your phone can play many types of files: AMR-NB/WB,  
MP3, PCM/WAV, AAC, AAC+, eAAC+, MIDI, OGG, and  
WMA.  
Set Up Music  
What Music Transfer Tools Do I Need?  
To put music on your computer and then load it on  
your phone, you need:  
A Microsoft® Windows® PC.  
Note: Your phone does not support any DRM protected files.  
What Headphones Can I Use?  
A USB data cable (included).  
Your phone has a 2.5mm headset jack for wired stereo  
listening. You can go wireless with Bluetooth® stereo  
headphones or speakers (see “12. Bluetooth®  
You Need a Memory Card  
Your music is stored on your memory card. Your phone  
supports removable microSD memory cards up to  
32 GB capacity. To make sure your memory card is  
Get Music  
Transfer Music Using USB  
Tip: To see the available memory on your memory card,  
Transfer music files from a computer to your memory  
card.  
touch  
>
Settings > SD card & phone  
storage.  
1. With a memory card inserted, and your phone  
showing the home screen, connect the Motorola  
micro USB data cable from your phone’s micro  
109  
         
USB port to a USB port on your computer. Your  
phone should show in the status bar.  
Play Music  
Note: Make sure to connect the phone to a high power USB  
port. Typically, these are located directly on your  
computer.  
Music Library  
Open your music library, then select what you want to  
play.  
Note: Your phone supports Microsoft™ Windows™ XP and  
Windows Vista™. Other operating systems may not be  
compatible.  
Touch  
>
Music.  
Music  
2. Your phone shows  
in the notifications bar. You  
can’t use the files on your memory card while it is  
connected.  
3. Touch Mount (if asked) to connect your memory  
Artists  
Songs  
Albums  
card.  
Categories  
Touch to list songs or  
playlists.  
4. Find “Removable Device” (your memory card) in  
the “My Computer” window.  
5. Drag and drop your music to a folder on your  
memory card.  
Playlists  
6. To help manage your music, create a “Music”  
folder on your memory card.  
Music Artist  
Song Title  
Last Played  
Touch to play again.  
7. When you’re done, use your computer’s “Safely  
Remove Hardware” feature to finish.  
110  
 
Your music is stored by artists, albums, songs, and  
playlists. Touch a category, then touch the song or  
playlist you want to play. Press Menu / > Party shuffle  
to randomly play all your songs.  
Music Player Controls  
Play/Pause  
Touch  
Touch  
/
/
.
.
Previous/Next  
Fast Forward/Rewind  
View Playlist  
Shuffle  
Touch & hold  
/
.
Music Player Functions  
Just touch a song or playlist to get going.  
Touch  
Touch  
Touch  
.
.
.
Open Playlist  
Repeat  
Volume  
Press the side Volume  
button.  
Shuffle On/Off  
View Library  
Press / > Library.  
Repeat Off/All  
/Current  
Turn Shuffle On/Off  
Add to Playlist  
Use as Ringtone  
Delete  
Press / > Party shuffle.  
Press / > Add to playlist.  
Press / > Use as ringtone.  
Press / > Delete.  
Music Artist  
Album Title  
Song Title  
Artist  
Album  
Song Title  
Music Controls  
1:14  
3:45  
Total Song Time  
Progress Bar  
111  
 
Hide, Wake, Turn Off  
Press Home X to use another app. Your music  
continues to play.  
When you see  
in the status bar a song is playing,  
flick down to see details. Touch the song to return to  
the music controls.  
To turn off your music, touch  
.
Playlists  
To add a song from the music library to a playlist, touch  
and hold the song then touch Add to playlist. Choose  
an existing playlist, or touch New to create a new  
playlist.  
To add a song to the playlist you’re playing, press  
Menu / > Add to playlist in the music player.  
To edit, delete, and rename playlists, touch and hold  
the playlist in the music library.  
112  
Safety and Warranty  
Information  
Failure to read and follow the information provided in this  
phone guide may result in serious bodily injury, death, or  
property damage.  
S1. Important Safety  
Information  
General Precautions  
There are several simple guidelines to operating your phone  
properly and maintaining safe, satisfactory service.  
To maximize performance, do not touch the bottom portion  
of your phone where the internal antenna is located while  
using the phone.  
Speak directly into the mouthpiece.  
Your mobile device is designed to resist damage from  
exposure to certain rugged conditions. Avoid prolonged or  
extreme exposure to those conditions.  
Any changes or modifications to your phone not expressly  
approved in this document could void your warranty for this  
equipment and void your authority to operate this  
equipment.  
Note: For the best care of your phone, only authorized personnel  
should service your phone and accessories. Failure to do  
so may be dangerous and void your warranty.  
114  
       
Following Safety Guidelines  
Maintaining Safe Use of and Access  
to Your Phone  
To operate your phone safely and efficiently, always follow any  
special regulations in a given area. Turn your phone off in areas  
where use is forbidden or when it may cause interference or  
danger.  
Do Not Rely on Your Phone for Emergency Calls  
Mobile phones operate using radio signals, which cannot  
guarantee connection in all conditions. Therefore you should  
never rely solely upon any mobile phone for essential  
communication (e.g., medical emergencies). Emergency calls  
may not be possible on all cellular networks or when certain  
network services or mobile phone features are in use. Check  
with your local service provider for details.  
Using Your Phone Near Other Electronic Devices  
Most modern electronic equipment is shielded from radio  
frequency (RF) signals. However, RF signals from wireless  
phones may affect inadequately shielded electronic  
equipment.  
RF signals may affect improperly installed or inadequately  
shielded electronic operating systems or entertainment  
systems in motor vehicles. Check with the manufacturer or their  
representative to determine if these systems are adequately  
shielded from external RF signals. Also check with the  
manufacturer regarding any equipment that has been added to  
your vehicle.  
Using Your Phone While Driving  
Talking on your phone while driving (or operating the phone  
without a hands-free device) is prohibited in some jurisdictions.  
Laws vary as to specific restrictions. Remember that safety  
always comes first.  
Consult the manufacturer of any personal medical devices,  
such as pacemakers and hearing aids, to determine if they are  
adequately shielded from external RF signals.  
Responsible driving practices can be found in “Smart Practices  
While Driving” on page 131 and/or at the Motorola website:  
www.motorola.com/callsmart.  
Tip: Purchase an optional hands-free accessory at your local  
Sprint Store, or call Nextel at 1-866-866-7509.  
115  
   
When using your radio product as a traditional  
two-way radio, hold the radio product in a  
vertical position with the microphone one to  
two inches (2.5 to 5 cm) away from the lips.  
Operational Precautions  
Note: Always turn off the phone in healthcare facilities, and  
request permission before using the phone near medical  
equipment.  
If you wear a radio product on your body when  
transmitting, always place the radio product in  
To assure optimal radio product performance and to be sure  
that human exposure to RF does not exceed the guidelines set  
forth in the relevant standards, always follow these instructions  
and precautions:  
a Motorola approved clip, holder, holster, case or body harness.  
If you do not use a body-worn accessory supplied or approved  
by Motorola and are not using the radio product in the intended  
use positions along side the head in the phone mode or in  
front of the face in the two-way radio mode, or if you hang your  
device from a lanyard around your neck, keep the device at  
least 2.5 centimeters (1 inch) from your body when transmitting.  
Phone Operation  
When placing or receiving a phone call, hold your radio  
product as you would a wireline telephone. Speak directly into  
the microphone.  
Approved Accessories  
Two-way Radio Operation  
For a list of approved Motorola accessories call 1-800-453-0920,  
or visit our website at www.motorola.com/phoneaccessories.  
Your radio product has been designed and tested to comply  
with national and international standards and guidelines  
regarding human exposure to RF electromagnetic energy,  
when operated in the two-way mode (at the face, or at the  
abdomen when using an audio accessory) at usage factors of  
up to 50% talk/50% listen.  
Turning Off Your Phone Before Flying  
Turn off your phone before boarding any aircraft. To prevent  
possible interference with aircraft systems, the U.S. Federal  
Aviation Administration (FAA) regulations require you to have  
permission from a crew member to use your phone while  
the plane is on the ground. To prevent any risk of interference,  
FCC regulations prohibit using your phone while the plane is in  
the air.  
Transmit no more than the rated duty factor of 50% of the time.  
To transmit (talk), push the PTT button. To receive calls, release  
the PTT button. Transmitting 50% of the time or less, is  
important because this radio generates measurable RF energy  
only when transmitting (in terms of measuring for standards  
compliance).  
116  
A choking hazard may exist for small, detachable parts.  
Turning Off Your Phone in Dangerous Areas  
Improper use could result in loud sounds, possibly causing  
hearing injury.  
To avoid interfering with blasting operations, turn your phone  
off when in a blasting area or in other areas with signs  
indicating two-way radios should be turned off. Construction  
crews often use remote-control RF devices to set off explosives.  
Improperly handled batteries could overheat and cause a  
burn.  
Do not allow children to play with your phone as they could  
hurt themselves and others, damage the phone or make calls  
that increase your invoice.  
Turn your phone off when you’re in any area that has a  
potentially explosive atmosphere. Although it’s rare, your phone  
and accessories could generate sparks. Sparks can cause an  
explosion or fire, resulting in bodily injury or even death. These  
areas are often, but not always, clearly marked. They include:  
Glass Parts  
Some parts of your phone may be made of glass. This glass  
could break if the product is dropped on a hard surface or  
receives a substantial impact. If glass breaks, do not touch or  
attempt to remove. Stop using your phone until the glass is  
replaced by a qualified service center.  
Fueling areas such as gas stations.  
Below deck on boats.  
Fuel or chemical transfer or storage facilities.  
Areas where the air contains chemicals or particles such  
as grain, dust, or metal powders.  
Seizures/Blackouts  
Any other area where you would normally be advised to  
turn off your vehicle’s engine.  
Some people may be susceptible to epileptic seizures or  
blackouts when exposed to flashing lights, such as when  
playing video games. These may occur even if a person has  
never had a previous seizure or blackout.  
Note: Never transport or store flammable gas, flammable liquids,  
or explosives in the compartment of your vehicle that  
contains your phone or accessories.  
If you have experienced seizures or blackouts, or if you have a  
family history of such occurrences, please consult with your  
physician before playing video games or enabling a flashing-  
lights feature (if available) on your phone.  
Keep Your Mobile Device and Its Accessories Away  
From Small Children  
These products are not toys and may be hazardous to children.  
For example:  
Discontinue use and consult a physician if any of the following  
symptoms occur: convulsion, eye or muscle twitching, loss of  
117  
awareness, involuntary movements, or disorientation. It is  
always a good idea to hold the screen away from your eyes,  
leave the lights on in the room, take a 15-minute break every  
hour, and stop use if you are very tired.  
Repetitive Motion  
When you repetitively perform actions such as pressing keys or  
entering finger-written characters, you may experience  
occasional discomfort in your hands, arms, shoulders, neck, or  
other parts of your body. If you continue to have discomfort  
during or after such use, stop use and see a physician.  
Caution About High Volume Usage  
Battery Use and Safety  
WARNING: Exposure to loud noise from any source for extended  
periods of time may affect your hearing. The louder  
the volume sound level, the less time is required  
before your hearing could be affected.  
Important: HANDLE AND STORE BATTERIES PROPERLY TO  
AVOID INJURY OR DAMAGE. Most battery issues  
arise from improper handling of batteries, and  
particularly from the continued use of damaged  
batteries.  
To protect your hearing:  
Limit the amount of time you use headsets or headphones at  
high volume.  
Avoid turning up the volume to block out noisy surroundings.  
DON’Ts  
Turn the volume down if you can’t hear people speaking  
near you.  
Don’t disassemble, crush, puncture, shred, or otherwise  
attempt to change the form of your battery.  
If you experience hearing discomfort, including the sensation of  
pressure or fullness in your ears, ringing in your ears, or  
muffled speech, you should stop listening to the device through  
your headset or headphones and have your hearing checked.  
Don’t let the phone or battery come in contact with water.  
Water can get into the phone’s circuits, leading to corrosion.  
If the phone and/or battery get wet, have them checked by  
your carrier or contact Motorola, even if they appear to be  
working properly.  
For more information about hearing, see our website at  
direct.motorola.com/hellomoto/nss/AcousticSafety.asp (in English  
only).  
Don’t allow the battery to touch metal objects. If metal  
objects, such as jewelry, stay in prolonged contact with the  
battery contact points, the battery could become very hot.  
118  
     
Don’t place your battery near a heat source. Excessive heat  
can damage the phone or the battery. High temperatures  
can cause the battery to swell, leak, or malfunction.  
Therefore:  
display such as Invalid Battery or Unable to Charge, take the  
following steps:  
Remove the battery and inspect it to confirm that it has a  
“Motorola Original” hologram;  
Do not dry a wet or damp battery with an appliance or  
heat source, such as a hair dryer or microwave oven.  
If there is no hologram, the battery is not a Motorola battery;  
If there is a hologram, replace the battery and retry charging  
it;  
Avoid leaving your phone in your car in high  
temperatures.  
If the message remains, contact a Motorola Authorized  
Service Center.  
DOs  
Important: Motorola’s warranty does not cover damage to the  
phone caused by non-Motorola batteries and/or  
chargers.  
Do avoid dropping the battery or phone. Dropping these  
items, especially on a hard surface, can potentially cause  
damage.  
Do contact your service provider or Motorola if your phone  
or battery has been damaged from dropping or high  
temperatures.  
WARNING: Use of a non-Motorola battery or charger may  
present a risk of fire, explosion, leakage, or other  
hazard.  
Important: USE MOTOROLA ORIGINAL PRODUCTS FOR  
QUALITY ASSURANCE AND SAFEGUARDS. To aid  
consumers in identifying authentic Motorola batteries  
from non-original or counterfeit batteries (that may not  
have adequate safety protection), Motorola provides  
holograms on its batteries. Consumers should  
confirm that any battery they purchase has a  
Proper and Safe Battery Disposal and Recycling  
Proper battery disposal is not only important for safety, it  
benefits the environment. Consumers may recycle their used  
batteries in many retail or service provider locations. Additional  
information on proper disposal and recycling may be found on  
the Web:  
“Motorola Original” hologram.  
www.motorola.com/recycling  
Motorola recommends you always use Motorola-branded  
batteries and chargers. Motorola mobile devices are designed  
to work with Motorola batteries. If you see a message on your  
www.rbrc.org/call2recycle/ (in English only)  
119  
Disposal of Lithium Ion (LiIon) Batteries: Promptly  
dispose of used batteries in accordance with local  
regulations. Contact your local recycling center or  
national recycling organizations for more information  
on how to dispose of batteries.  
manufacturer, or call 1-866-866-7509 to order. They’re also  
available at www.nextel.com — click Accessories. Buying the  
right batteries and accessories is the best way to ensure  
they’re genuine and safe.  
In order to avoid damage, charge the battery only in  
temperatures that range from 32° F to 113° F (0° C to 45° C).  
Do not handle a damaged or leaking Li-Ion battery as you can  
be burned.  
Don’t use the battery charger in direct sunlight or in high  
humidity areas, such as the bathroom.  
WARNING: Never dispose of batteries in a fire because they may  
Never dispose of the battery by incineration.  
explode.  
Keep the metal contacts on top of the battery clean.  
Don’t attempt to disassemble or short-circuit the battery.  
Special Note: Be sure to dispose of your battery properly. In  
some areas, the disposal of batteries in household or business  
trash may be prohibited.  
The battery may need recharging if it has not been used for  
a long period of time.  
Protecting Your Battery  
The guidelines listed below help you get the most out of your  
battery’s performance.  
It’s best to replace the battery when it no longer provides  
acceptable performance. It can be recharged hundreds of  
times before it needs replacing.  
Don’t store the battery in high temperature areas for long  
periods of time. It’s best to follow these storage rules:  
Recently there have been some public reports of wireless  
phone batteries overheating, catching fire, or exploding. It  
appears that many, if not all, of these reports involve  
counterfeit or inexpensive, aftermarket-brand batteries with  
unknown or questionable manufacturing standards. Nextel is  
not aware of similar problems with Nextel phones resulting  
from the proper use of batteries and accessories approved  
by Nextel or the manufacturer of your phone. Use only  
Nextel-approved or manufacturer-approved batteries and  
accessories found at Sprint Stores or through your phone’s  
Less than one month:  
-4° F to 140° F (-20° C to 60° C)  
More than one month:  
-4° F to 113° F (-20° C to 45° C)  
120  
 
Batteries and Chargers  
Your battery, charger, or portable radio may contain symbols,  
defined as follows:  
Using Your Phone With a Hearing  
Aid Device  
A number of Nextel phones have been tested for hearing aid  
device compatibility. When some wireless phones are used  
with certain hearing devices (including hearing aids and  
cochlear implants), users may detect a noise which can  
interfere with the effectiveness of the hearing device.  
Symbol  
Definition  
032374o  
Important safety information  
follows.  
Do not dispose of your battery or  
phone in a fire.  
Some hearing devices are more immune than others to this  
interference noise, and phones also vary in the amount of  
interference noise they may generate. ANSI standard C63.19  
was developed to provide a standardized means of measuring  
both wireless phone and hearing devices to determine usability  
rating categories for both.  
Your battery or phone may require  
recycling in accordance with local  
laws. Contact your local regulatory  
authorities for more information.  
032375o  
Ratings have been developed for mobile phones to assist  
hearing device users find phones that may be compatible with  
their hearing device. Not all phones have been rated for  
compatibility with hearing devices. Phones that have been  
rated have a label with the rating(s) located on the box, and are  
listed at www.motorola.com/accessibility.  
Do not throw your battery or  
phone in the trash.  
Your phone contains an internal  
lithium ion battery.  
Li Ion BATT  
032378o  
These ratings are not guarantees. Results will vary depending  
on the user’s hearing device and individual type and degree of  
hearing loss. If a hearing device is particularly vulnerable to  
interference noise; even a phone with a higher rating may still  
cause unacceptable noise levels in the hearing device. Trying  
Do not let your battery, charger, or  
phone get wet.  
Listening at full volume to music  
or voice through a headset may  
damage your hearing.  
121  
     
out the phone with your hearing device is the best way to  
evaluate it for your personal needs.  
find the one that works best with your hearing aid device.  
Should you experience interference or find the quality of  
service unsatisfactory after purchasing your phone, promptly  
return it to the store within 30 days of purchase. With the Sprint  
30-day Risk-Free Guarantee, you may return the phone within  
30 days of purchase for a full refund. More information about  
hearing aid compatibility may be found at:  
M-Ratings: Phones rated M3 or M4 meet FCC requirements  
for hearing aid compatibility and are likely to generate less  
interference to hearing devices than unrated phones. (M4 is the  
better/higher of the two ratings.)  
T-Ratings: Phones rated T3 or T4 meet FCC requirements and  
are likely to be more usable with a hearing device’s telecoil (“T  
Switch”or “Telephone Switch”) than unrated phones. (T4 is the  
better/higher of the two ratings. Note that not all hearing  
devices have telecoils in them.)  
www.motorola.com/accessibility, www.fcc.gov, www.fda.gov, and  
www.accesswireless.org.  
Getting the Best Hearing Device Experience With  
Your Phone  
Hearing aid devices may also be measured for immunity to  
interference noise from wireless phones and should have  
ratings similar to phones. Ask your hearing health care  
professional for the rating of your hearing aid. Add the rating of  
your hearing aid and your phone to determine probable  
usability:  
To further minimize interference:  
Set the phone’s display and keypad backlight settings to  
ensure the minimum time interval:  
1. Press / > Settings > Sound & display >  
Screen timeout.  
Any combined rating equal to or greater than six offers  
excellent use.  
2. Touch the minimum time interval (15 seconds).  
Position the phone so the internal antenna is farthest from  
your hearing aid.  
Any combined rating equal to five is considered normal use.  
Any combined rating equal to four is considered usable.  
Move the phone around to find the point with least  
interference.  
Thus, if you pair an M3 hearing aid with an M3 phone, you will  
have a combined rating of six for “excellent use.”This is  
synonymous for T ratings.  
Nextel further suggests you experiment with multiple phones  
(even those not labeled M3/T3 or M4/T4) while in the store to  
122  
Caring for the Environment by  
Recycling  
Export Law Assurances  
This product is controlled under the export regulations of the  
United States of America and Canada. The Governments of the  
United States of America and Canada may restrict the  
exportation or re-exportation of this product to certain  
destinations. For further information contact the U.S.  
Department of Commerce or the Canadian Department of  
Foreign Affairs and International Trade.  
This symbol on a Motorola product means the product  
should not be disposed of with household waste.  
Disposal of your Mobile Device and Accessories  
Please do not dispose of mobile devices or electrical  
accessories (such as chargers, headsets, or batteries) with  
your household waste. These items should be disposed of in  
accordance with the national collection and recycling schemes  
operated by your local or regional authority. Alternatively, you  
may return unwanted mobile devices and electrical  
accessories to any Motorola Approved Service Center in your  
region. Details of Motorola approved national recycling  
schemes, and further information on Motorola recycling  
activities can be found at: www.motorola.com/recycling.  
California Perchlorate Label  
Some mobile phones use an internal, permanent backup  
battery on the printed circuit board that may contain very small  
amounts of perchlorate. In such cases, California law requires  
the following label:  
Perchlorate Material – special handling may apply. See  
www.dtsc.ca.gov/hazardouswaste/perchlorate. There is no special  
handling required by consumers.  
Disposal of your Mobile Device Packaging and  
User’s Guide  
Radio Frequency (RF) Energy  
Product packaging and user’s guides should only be disposed  
of in accordance with national collection and recycling  
requirements. Please contact your regional authorities for more  
details.  
This section contains important information on the safe and  
efficient operation of your mobile device. Read this  
information before using your mobile device.  
123  
           
Using accessories not supplied or approved by Motorola may  
cause your mobile device to exceed RF energy exposure  
guidelines. For a list of Motorola-supplied or approved  
accessories, visit our website at: www.motorola.com.  
Exposure to Radio Frequency (RF) Energy  
Your mobile device contains a transmitter and receiver. When it  
is ON, it receives and transmits RF energy. When you  
communicate with your mobile device, the system handling  
your call controls the power level at which your mobile device  
transmits.  
RF Energy Interference/Compatibility  
Nearly every electronic device is subject to RF energy  
interference from external sources if inadequately shielded,  
designed, or otherwise configured for RF energy compatibility.  
In some circumstances your mobile device may cause  
interference with other devices.  
Your Motorola mobile device is designed to comply with local  
regulatory requirements in your country concerning exposure  
of human beings to RF energy.  
Operational Precautions  
Follow Instructions to Avoid Interference Problems  
For optimal mobile device performance, and to be sure that  
human exposure to RF energy does not exceed the guidelines  
set forth in the relevant standards, always follow these  
instructions and precautions.  
Turn off your mobile device in any location where posted  
notices instruct you to do so.  
In an aircraft, turn off your mobile device whenever instructed  
to do so by airline staff.  
Product Operation  
When placing or receiving a phone call, hold your mobile  
device just like you would a landline phone.  
If your mobile device offers an airplane mode or similar  
feature, consult airline staff about using it in flight.  
Implantable Medical Devices  
If you wear the mobile device on your body, always place the  
mobile device in a Motorola-supplied or approved clip, holder,  
holster, case, or body harness. If you do not use a body-worn  
accessory supplied or approved by Motorola—or if you hang  
your mobile device from a lanyard around your neck—keep the  
mobile device and its antenna at least 2.5 centimeters (1 inch)  
from your body when transmitting.  
If you have an implantable medical device, such as a  
pacemaker or defibrillator, consult your physician before using  
this mobile device.  
124  
Persons with implantable medical devices should observe the  
following precautions:  
Operational Warnings  
Obey all posted signs when using mobile devices in public  
areas.  
ALWAYS keep the mobile device more than 20 centimeters  
(8 inches) from the implantable medical device when the  
mobile device is turned ON.  
Potentially Explosive Atmospheres  
DO NOT carry the mobile device in the breast pocket.  
Areas with potentially explosive atmospheres are often, but not  
always, posted and can include fueling areas, such as below  
decks on boats, fuel or chemical transfer or storage facilities, or  
areas where the air contains chemicals or particles, such as  
grain dust, or metal powders.  
Use the ear opposite the implantable medical device to  
minimize the potential for interference.  
Turn OFF the mobile device immediately if you have any  
reason to suspect that interference is taking place.  
Read and follow the directions from the manufacturer of your  
implantable medical device. If you have any questions about  
using your mobile device with your implantable medical  
device, consult your healthcare provider.  
When you are in such an area, turn off your mobile device, and  
do not remove, install, or charge batteries. In such areas,  
sparks can occur and cause an explosion or fire.  
Knowing Radio Frequency Safety  
Driving Precautions  
The use of wireless phones while driving may cause  
distraction. Discontinue a call if you can’t concentrate on  
driving.  
The design of your phone complies with updated NCRP standards  
described below.  
In 1991–92, the Institute of Electrical and Electronics Engineers  
(IEEE) and the American National Standards Institute (ANSI) joined  
in updating ANSI’s 1982 standard for safety levels with respect to  
human exposure to RF signals. More than 120 scientists, engineers  
and physicians from universities, government health agencies and  
industries developed this updated standard after reviewing the  
available body of research. In 1993, the Federal Communications  
Commission (FCC) adopted this updated standard in a regulation.  
In August 1996, the FCC adopted hybrid standard consisting of the  
existing ANSI/IEEE standard and the guidelines published by the  
Additionally, the use of wireless devices and their accessories  
may be prohibited or restricted in certain areas. Always obey  
the laws and regulations on the use of these products.  
Responsible driving practices can be found in the “Smart  
Practices While Driving” section in this guide (or separate  
guide).  
125  
National Council of Radiation Protection and Measurements  
(NCRP).  
American National Standards Institute (ANSI) / Institute of  
Electrical and Electronics Engineers (IEEE). C95. 1-1992.  
Institute of Electrical and Electronics Engineers (IEEE). C95.  
Body-Worn Operation  
1-2005 Edition.1  
To maintain compliance with FCC RF exposure guidelines, if  
you wear a handset on your body, use the Motorola supplied or  
approved carrying case, holster or other body-worn accessory.  
If you do not use a body-worn accessory, ensure the antenna is  
at least 2.5 centimeters from your body when transmitting. Use  
of non-Motorola-approved accessories may violate FCC RF  
exposure guidelines.  
International Commission on Non-Ionizing Radiation  
Protection (ICNIRP) 1998.  
Ministry of Health (Canada). Safety Code 6. Limits of Human  
Exposure to Radio frequency Electromagnetic Fields in the  
Frequency Range from 3 kHz to 300 GHz, 1999.  
Australian Communications Authority Radio  
communications (Electromagnetic Radiation - Human  
Exposure) Standard 2003.  
Your Motorola phone is designed to comply with local  
regulatory requirements in your country concerning exposure  
of human beings to RF energy.  
ANATEL, Brazil Regulatory Authority, Resolution 303 (July 2,  
2002) “Regulation of the limitation of exposure to electrical,  
magnetic, and electromagnetic fields in the radio frequency  
range between 9 kHz and 300 GHz.” “Attachment to  
Resolution 303 from July 2, 2002.”  
For more information about RF exposure, visit the FCC website  
at www.fcc.gov.  
Portable Radio Product Operation and EME Exposure  
Your Motorola radio product is designed to comply with the  
following national and international standards and guidelines  
regarding exposure of human beings to radio frequency  
electromagnetic energy (EME):  
United States Federal Communications Commission, Code  
of Federal Regulations; 47 CFR part 2 sub-part J.  
1.The information provided in this document supersedes the  
general safety information in user’s guides published prior to  
May 1, 2006.  
126  
multiple power levels so as to use only the power required to  
reach the network. In general, the closer you are to a wireless  
base station, the lower the power output.  
Specific Absorption Rate  
Your MOTOROLA i1 wireless phone meets the  
governmental requirements for exposure to radio waves.  
Before a phone model is available for sale to the public in the  
U.S. and Canada, it must be tested and certified to the FCC  
and Industry Canada that it does not exceed the limit  
established by each government for safe exposure. The tests  
are performed in positions and locations (e.g., at the ear and  
worn on the body) submitted to the FCC and available for  
review by Industry Canada. The highest SAR value for this  
model phone when tested for use at the ear is 1.30 W/kg, and  
when worn on the body, as described in this user guide, is  
0.95 W/kg. Body-worn measurements can differ, depending  
upon available accessories and regulatory requirements. The  
SAR information includes the Motorola testing protocol,  
assessment procedure, and measurement uncertainty range  
for this product.  
Your wireless phone is a radio transmitter and receiver. It is  
designed and manufactured to not exceed limits for exposure  
to radio frequency (RF) energy set by the Federal  
Communications Commission (FCC) of the U.S. Government  
and by the Canadian regulatory authorities. These limits are  
part of comprehensive guidelines and establish permitted  
levels of RF energy for the general population. The guidelines  
are based on standards that were developed by independent  
scientific organizations through periodic and thorough  
evaluation of scientific studies. The standards include a  
substantial safety margin designed for the safety of all persons,  
regardless of age or health, and to account for any variations in  
measurements.  
The exposure standard for wireless mobile phones employs a  
unit of measurement known as the Specific Absorption Rate  
(SAR). The SAR limit set by the FCC and by the Canadian  
regulatory authorities is 1.6 watts per kilogram (W/kg),  
averaged over one gram of tissue. Tests for SAR are conducted  
using procedures accepted by the FCC and by Industry  
Canada with the phone transmitting at its highest certified  
power level in all tested frequencies. Although the SAR is  
determined at the highest certified power level, the actual SAR  
level of the phone while operating can be below the maximum  
value. This is because the phone is designed to operate at  
While there may be differences between the SAR levels of  
various phones and at various positions, they meet the  
governmental requirements for safe exposure. Please note that  
improvements to this product model could cause differences in  
the SAR value for later products; in all cases, products are  
designed to be within the guidelines.  
Additional information on SAR can be found on the Cellular  
Telecommunications & Internet Association (CTIA) website:  
www.phonefacts.net or the Canadian Wireless  
Telecommunications Association (CWTA) website: www.cwta.ca.  
127  
Owner’s Record  
Software Copyright Notice  
The model number, regulatory number, and serial number are  
located on a nameplate inside the battery compartment.  
Record the serial number in the space provided below. This will  
be helpful if you need to contact us about your phone in the  
future.  
The Motorola products described in this manual may include  
copyrighted Motorola and third party software stored in  
semiconductor memories or other media. Laws in the United  
States and other countries preserve for Motorola and third party  
software providers certain exclusive rights for copyrighted  
software, such as the exclusive rights to distribute or reproduce  
the copyrighted software. Accordingly, any copyrighted  
software contained in the Motorola products may not be  
modified, reverse-engineered, distributed, or reproduced in any  
manner to the extent allowed by law. Furthermore, the  
purchase of the Motorola products shall not be deemed to  
grant either directly or by implication, estoppel, or otherwise,  
any license under the copyrights, patents, or patent  
Model: MOTOROLA i1  
Serial No.:  
Online Product Registration:  
http://www.motorola.com/us/productregistration  
Product registration is an important step toward enjoying your  
new Motorola product. Registration permits us to contact you  
for product or software updates and allows you to subscribe to  
updates on new products or special promotions. Registration is  
not required for warranty coverage. Please retain your original  
dated sales receipt, as you may need to provide it for warranty  
validation in the future.  
applications of Motorola or any third party software provider,  
except for the normal, non-exclusive, royalty-free license to use  
that arises by operation of law in the sale of a product.  
Thank you for choosing a Motorola product.  
128  
     
Open Source Software Information  
GPS and AGPS  
For instructions on how to obtain a copy of any source code  
being made publicly available by Motorola related to software  
used in this Motorola mobile device you may send your request  
in writing to:  
Your mobile device can use Global Positioning System (GPS)  
signals for location-based applications. GPS uses satellites  
controlled by the U.S. government that are subject to changes  
implemented in accordance with the Department of Defense  
policy and the Federal Radio Navigation Plan. These changes  
may affect the performance of location technology on your  
mobile device.  
MOTOROLA, INC.  
OSS Management  
600 North US Hwy 45  
Libertyville, IL 60048  
USA  
Your mobile device can also use Assisted Global Positioning  
System (AGPS), which obtains information from the cellular  
network to improve GPS performance. AGPS uses your  
wireless service provider's network and therefore airtime, data  
charges, and/or additional charges may apply in accordance  
with your service plan. Contact your wireless service provider  
for details.  
The Motorola website opensource.motorola.com also contains  
information regarding Motorola’s use of open source.  
Motorola has created the opensource.motorola.com to serve as a  
portal for interaction with the software community-at-large.  
To view additional information regarding licenses,  
acknowledgments and required copyright notices for open  
source packages used in this Motorola mobile device, please  
Your Location  
touch  
> Settings> About Phone > Legal information >  
Location-based information includes information that can be  
used to determine the approximate location of a mobile device.  
Mobile phones which are connected to a wireless network  
transmit location-based information. Devices enabled with GPS  
or AGPS technology also transmit location-based information.  
Additionally, if you use applications that require location-based  
information (e.g. driving directions), such applications transmit  
location-based information. This location-based information  
may be shared with third parties, including your wireless  
Open source licenses.  
129  
   
service provider, applications providers, Motorola, and other  
third parties providing services.  
Privacy and Data Security  
Motorola understands that privacy and data security are  
important to everyone. Because some features of your phone  
may affect your privacy or data security, please follow these  
recommendations to enhance protection of your information:  
Emergency Calls  
When you make an emergency call, the cellular network may  
activate the AGPS technology in your mobile device to tell the  
emergency responders your approximate location.  
Monitor access: Keep your phone with you and do not leave  
it where others may have unmonitored access. Lock your  
device’s keypad where this feature is available.  
AGPS has limitations and might not work in your area.  
Therefore:  
Always tell the emergency responder your location to the  
best of your ability; and  
Keep software up to date: If Motorola or a software/  
application vendor releases a patch or software fix for your  
phone which updates the device’s security, install it as soon  
as possible.  
Remain on the phone for as long as the emergency  
responder instructs you.  
Erase before recycling: Delete personal information or data  
from your phone prior to disposing of it or turning it in for  
recycling. For step-by-step instructions on how to delete all  
personal information from your device, please contact your  
local service provider.  
Performance Tips  
Go outside and away from underground locations, covered  
vehicles, structures with metal or concrete roofs, tall  
buildings, and foliage. Indoor performance might improve if  
you move closer to windows, but some window sun  
shielding films can block satellite signals.  
Understanding AGPS: In order to comply with emergency  
caller location requirements of the FCC, certain Motorola  
phones incorporate Assisted Global Positioning System  
(AGPS) technology. AGPS technology also can be used in  
non-emergency applications to track and monitor a user’s  
location, for example, to provide driving directions. Users  
who prefer not to permit such tracking and monitoring  
should avoid using such applications.  
Move away from radios, entertainment equipment, and other  
electronic devices.  
130  
 
If you have further questions regarding how use of your phone  
may impact your privacy or data security, please contact  
Motorola.  
Position your phone within easy reach. Be able to access  
your phone without removing your eyes from the road. If you  
receive an incoming call at an inconvenient time, if possible,  
let your voice mail answer it for you.  
Let the person you are speaking with know you are driving; if  
necessary, suspend the call in heavy traffic or hazardous  
weather conditions. Rain, sleet, snow, ice, and even heavy  
traffic can be hazardous.  
Smart Practices While Driving  
Drive Safe, Call Smart SM  
Do not take notes or look up phone numbers while driving.  
Jotting down a “to do” list or going through your address  
book takes attention away from your primary responsibility,  
driving safely.  
Check the laws and regulations on the use of mobile devices  
and their accessories in the areas where you drive. Always  
obey them. The use of these devices may be prohibited or  
restricted in certain areas. Contact www.motorola.com/callsmart  
for more information.  
Dial sensibly and assess the traffic; if possible, place calls  
when your car is not moving or before pulling into traffic. If  
you must make a call while moving, dial only a few numbers,  
check the road and your mirrors, then continue.  
Your mobile device lets you communicate by voice and data—  
almost anywhere, anytime, wherever wireless service is  
available and safe conditions allow. When driving a car, driving  
is your first responsibility. If you choose to use your mobile  
device while driving, remember the following tips:  
Do not engage in stressful or emotional conversations that  
may be distracting. Make people you are talking with aware  
you are driving and suspend conversations that can divert  
your attention away from the road.  
Get to know your Motorola phone and its features such as  
speed dial and redial. If available, these features help you to  
place your call without taking your attention off the road.  
Use your phone to call for help. Dial 911 or other local  
emergency number in the case of fire, traffic accident, or  
medical emergencies.*  
When available, use a hands-free device. If possible, add an  
additional layer of convenience to your phone with one of the  
many Motorola Original hands-free accessories available  
today.  
131  
 
Use your phone to help others in emergencies. If you see an  
auto accident, crime in progress, or other serious emergency  
where lives are in danger, call 911 or other local emergency  
number, as you would want others to do for you.*  
Call roadside assistance or a special non-emergency  
wireless assistance number when necessary. If you see a  
broken-down vehicle posing no serious hazard, a broken  
traffic signal, a minor traffic accident where no one appears  
injured, or a vehicle you know to be stolen, call roadside  
assistance or other special non-emergency wireless  
number.*  
* Wherever wireless phone service is available  
132  
 
Motorola Limited Warranty  
for the United States and Canada  
S2. Manufacturer’s Warranty  
What does this Warranty Cover?  
Subject to the exclusions contained below, Motorola, Inc.  
warrants its telephones, pagers, messaging devices, and  
consumer and professional two-way radios (excluding  
commercial, government or industrial radios) that operate via  
Family Radio Service or General Mobile Radio Service,  
Motorola-branded or certified accessories sold for use with  
these Products (“Accessories”) and Motorola software  
contained on CD-ROMs or other tangible media and sold for  
use with these Products (“Software”) to be free from defects in  
materials and workmanship under normal consumer usage for  
the period(s) outlined below. This limited warranty is a  
consumer's exclusive remedy, and applies as follows to new  
Motorola Products, Accessories and Software purchased by  
consumers in the United States or Canada, which are  
accompanied by this written warranty:  
Your phone has been designed to provide you with  
reliable, worry-free service. If for any reason you have a  
problem with your equipment, please refer to the  
manufacturer’s warranty in this section.  
For information regarding the terms and conditions of service  
for your phone, please visit www.nextel.com or call Nextel  
Customer Service at 1-800-639-6111.  
133  
     
Products and Accessories  
Products Covered  
Length of Coverage  
Products Covered  
Length of Coverage  
Products and  
Accessories that are  
Repaired or  
The balance of the original  
warranty or for ninety (90)  
days from the date returned to  
the consumer, whichever is  
longer.  
Products and  
One (1) year from the date of  
purchase by the first consumer  
purchaser of the product unless  
otherwise provided for below.  
Accessories as  
defined above,  
unless otherwise  
provided for below.  
Replaced.  
Decorative  
Limited lifetime warranty for  
the lifetime of ownership by  
the first consumer purchaser  
of the product.  
Exclusions  
Accessories and  
Cases. Decorative  
covers, bezels,  
PhoneWrap™  
Normal Wear and Tear. Periodic maintenance, repair and  
replacement of parts due to normal wear and tear are excluded  
from coverage.  
covers and cases.  
Batteries. Only batteries whose fully charged capacity falls  
below 80% of their rated capacity and batteries that leak are  
covered by this limited warranty.  
Monaural Headsets. Limited lifetime warranty for  
Ear buds and boom the lifetime of ownership by  
Abuse, Misuse and Accidents. Defects or damage that result  
from abuse, misuse or accidents, including but not limited to:  
(a) improper handling, usage, operation or storage (e.g.  
operating the Product outside its permitted or intended uses  
including as set forth by Motorola in the Products specification  
sheets or other documentation, or failing to comply with the  
Products usage documentation); abuse/neglect (e.g. broken/  
bent/missing clips/fasteners/connectors); (b) contact with  
liquids, water, rain, extreme humidity, heavy perspiration or  
other moisture, sand, food, dirt or similar substances caused  
from incorrectly securing the phone’s protective elements or  
headsets that  
the first consumer purchaser  
of the product.  
transmit mono  
sound through a  
wired connection.  
Consumer and  
Professional  
Two-Way Radio  
Accessories.  
Ninety (90) days from the date  
of purchase by the first  
consumer purchaser of the  
product.  
134  
subjecting the Products to conditions beyond their stated  
specification or limits; (c) use of the Products for commercial  
rental purposes; or (d) external causes or acts which are not  
the fault of Motorola, including but not limited to flood, fire,  
earthquake, tornado or other acts of God, are excluded from  
coverage.  
Software  
Products Covered  
Length of Coverage  
Software. Applies only to  
physical defects in the media  
that embodies the copy of the  
software (e.g. CD-ROM, or  
floppy disk).  
Ninety (90) days  
from the date of  
purchase.  
Use of Non-Motorola Products and Accessories. Defects or  
damage that result from the use of Non-Motorola branded or  
certified Products, Accessories, Software or other peripheral  
equipment are excluded from coverage.  
Exclusions  
Unauthorized Service or Modification. Defects or damages  
resulting from service, testing, adjustment, installation,  
maintenance, alteration, or modification in any way by  
someone other than Motorola, or its authorized service centers,  
are excluded from coverage.  
Software Embodied in Physical Media. No warranty is made  
that the software will meet your requirements or will work in  
combination with any hardware or software applications  
provided by third parties, that the operation of the software  
products will be uninterrupted or error free, or that all defects in  
the software products will be corrected.  
Altered Products. Products or Accessories with (a) serial  
numbers or date tags that have been removed, altered or  
obliterated; (b) broken seals or that show evidence of  
tampering; (c) mismatched board serial numbers; or (d)  
nonconforming or non-Motorola housings, or parts, are  
excluded from coverage.  
Software NOT Embodied in Physical Media. Software that is not  
embodied in physical media (e.g. software that is downloaded  
from the internet), is provided “as is” and without warranty.  
Who Is Covered?  
This warranty extends only to the first consumer purchaser, and  
is not transferable.  
Communication Services. Defects, damages, or the failure of  
Products, Accessories or Software due to any communication  
service or signal you may subscribe to or use with the Products  
Accessories or Software is excluded from coverage.  
135  
(a) a copy of your receipt, bill of sale or other comparable proof  
of purchase; (b) a written description of the problem; (c) the  
name of your service provider, if applicable; (d) the name and  
location of the installation facility (if applicable) and, most  
importantly; (e) your address and telephone number.  
What Will Motorola Do?  
Motorola, at its option, will at no charge repair, replace or refund  
the purchase price of any Products, Accessories or Software  
that does not conform to this warranty. We may use functionally  
equivalent reconditioned/refurbished/pre-owned or new  
Products, Accessories or parts. No data, software or  
applications added to your Product, Accessory or Software,  
including but not limited to personal contacts, games and  
ringer tones, will be reinstalled. To avoid losing such data,  
software and applications please create a back up prior to  
requesting service.  
What other limitations are there?  
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT  
LIMITATION THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR  
PURPOSE, SHALL BE LIMITED TO THE DURATION OF THIS  
LIMITED WARRANTY, OTHERWISE THE REPAIR,  
REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS  
EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY  
OF THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL  
OTHER WARRANTIES, EXPRESS OR IMPLIED. IN NO EVENT  
SHALL MOTOROLA BE LIABLE, WHETHER IN CONTRACT OR  
TORT (INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS  
OF THE PURCHASE PRICE OF THE PRODUCT, ACCESSORY  
OR SOFTWARE, OR FOR ANY INDIRECT, INCIDENTAL,  
SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR  
LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS  
OF INFORMATION OR DATA, SOFTWARE OR APPLICATIONS  
OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN  
CONNECTION WITH THE ABILITY OR INABILITY TO USE THE  
PRODUCTS, ACCESSORIES OR SOFTWARE TO THE FULL  
EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.  
How to Obtain Warranty Service or Other  
Information  
USA  
Phones  
1-800-453-0920  
TTY  
1-877-483-2840  
For Accessories and Software, please call the  
telephone number designated above for the  
product with which they are used  
You will receive instructions on how to ship the Products,  
Accessories or Software, at your expense, to a Motorola  
Authorized Repair Center. To obtain service, you must include:  
136  
Some states and jurisdictions do not allow the limitation  
or exclusion of incidental or consequential damages, or  
limitation on the length of an implied warranty, so the  
above limitations or exclusions may not apply to you. This  
warranty gives you specific legal rights, and you may also  
have other rights that vary from state to state or from one  
jurisdiction to another.  
Laws in the United States and other countries preserve for  
Motorola certain exclusive rights for copyrighted Motorola  
software such as the exclusive rights to reproduce and  
distribute copies of the Motorola software. Motorola software  
may only be copied into, used in, and redistributed with, the  
Products associated with such Motorola software. No other use,  
including without limitation disassembly of such Motorola  
software or exercise of the exclusive rights reserved for  
Motorola, is permitted.  
Service and Repairs  
If you have questions or need assistance, we’re here to help.  
Go to www.motorola.com/support, where you can select from  
a number of customer care options. You can also contact the  
Motorola Customer Support Center at 1-800-453-0920 (United  
States), 1-877-483-2840 (TTY/TDD United States for hearing  
impaired).  
137  
   
Battery Life, Extend 66, 67, 105  
Bluetooth 105107  
Bluetooth Device Name 107  
Bookmarks 61  
Call Waiting 54  
Off 54  
Caller ID 53  
Index  
A
Accessories 25  
Calls  
Charger 25  
Direct Connect Calls 32  
Accessing 62  
Li-Ion Battery 25  
Activation 8  
From Contacts 34  
International 57  
Phone Call While in Direct  
Connect 32  
Phone Calls 28  
Talkgroup Calls 41  
Using the Member ID 34  
Creating 62  
C
Airplane Mode 72  
Alarm Clock 94  
Android Keyboard 21  
Answering Calls 28  
Applications 15  
Cables 98, 109  
Call Alerts  
Answer 43  
Deleting 44  
Queue 44  
Responding 44  
Sending 43  
Camcorder  
Attachments 51  
Viewing 44  
Camera 100104  
Talking Pictures 100  
Zoom 102  
Clock Display 71  
Contacts 8288  
Assign a Picture to an Entry  
Call Forwarding 55  
B
All Calls 55  
Off 56  
Backlight 70  
Battery 57  
Charging 7  
Disposal 120  
Call Log  
Deleting Call Log List 81  
Safety 118  
138  
 
Creating 83  
Pictures 37  
Removing Members 36  
Deleting 87  
Receiving My Info 41  
Receiving Pictures 38  
Display Screen 16  
Downloading Apps 63  
H
I
Making Direct Connect Calls  
Making Phone Calls 32  
Searching 85  
Hearing Aid Compatibility 121  
Icons  
Contacts 83  
E
Status Information 16  
In-Call Options 30  
International Numbers 57  
D
Email 64  
DC Options 73  
Dialing Codes  
Telecommunications Relay  
Service 57  
Direct Connect  
One Touch, Setting 73  
Direct Connect Calls  
Dialing 33  
From Contacts 34  
Member ID 34  
Direct Connect Numbers 33  
Direct Send 3741  
Contacts 40  
Emergency Numbers 29  
End-of-Call Options 31  
Entering Text 2123  
Event Edit 89  
K
L
Key Functions 13  
Keyboard 21  
G
Get Music 109  
Gmail 64  
Group Connect  
Adding Group Members 36  
Creating Groups 36  
Deleting 36  
Language 68  
Latitude 91  
M
Market  
Menu  
Navigation 18  
Messaging  
Groups vs. Talkgroups 41  
MMS Messages 47  
My Info 39  
139  
Notifications 46  
Text Messaging (SMS) 53  
Messaging Settings  
Notification 71  
Sending 39  
Phone Settings 6875  
Display Settings 7071  
Language 68  
Messaging Settings 7172  
Sound Settings 6870  
Prepend Dialing 73  
N
Navigating Through Menus 18  
Nextel Service  
microSD Card 9598  
Account Passwords 10  
Activation 8  
Adapter 97  
Inserting 95  
Memory 98  
R
Operator Services 11  
Non-Emergency Numbers 57  
Radio Frequency 123  
Recent Calls 7881  
Call Alerts 78  
Removing 96  
O
P
Attachments 51  
Calls From 51  
One Touch Direct Connect 73  
Owner’s Record 128  
My Info 79  
Remote Direct Connect Button  
Resetting Your Phone 76  
Ringtones 68  
Deleting 51  
Pause Button 111  
Pauses 31  
Embedded Objects 51  
Forwarding 50, 51  
Going to Website 52  
Receiving 50  
Storing 84  
Phone (illus.) 12  
Phone Number  
Finding 31  
Sending 48  
S
Multimedia Messages  
Music Set Up 109  
My Info  
Safety Information 114132  
Radio Frequency 123  
Tips 115  
Saving 31  
With Pauses 31  
Saving Attachments 53  
Receiving 41, 79  
140  
Screen Lock 75  
Search  
Touch Tips 18  
Transmitters  
Web 6062  
Bookmarks 62  
Go to Websites 62  
Reloading a Web Page 62  
Web Browser 60  
Widgets 14  
Turning On and Off 72  
TTY Devices 57  
Turning Your Phone On and Off  
Security 7476  
Setup Wizard 9  
Shortcuts 15  
Silent Mode 70  
SIM Card  
Removing and Inserting 3  
Security 74  
SIM PIN 74  
X
U
V
XT9 Text Input 22  
Unlocking Your Phone 76  
USB Cables 98, 109  
Vibrate All 69  
Video 103  
Swype Text Entry 23  
T
Recording 103  
Voicemail 47  
Talkgroups 41  
Join 42  
Setting Up 10, 47  
TDD/TTY Devices 57  
Telecommunications Relay  
Service 57  
W
Waits  
Text Entry 2123  
Text Messaging  
Three-Way Calling 55  
Storing 84  
Wallpaper 70  
Warranty 133137  
141  

Yamaha CRW4416SX User Manual
Toshiba Protege PT311U04K02V User Manual
Stiga SILENCIUM 8217 3033 01 User Manual
Seagate ST200FP0021 User Manual
Seagate HAWK ST15230DC User Manual
Samsung SGH x427 User Manual
Samsung GH68 02493A User Manual
Pioneer CD Player DEH P7100BT User Manual
Philips AJ3138 User Manual
Optimus 120 2152 User Manual