Seagate ST3250310NS User Manual

Product Manual  
Barracuda ES.2 Serial ATA  
ST31000340NS  
ST3750330NS  
ST3500320NS  
ST3250310NS  
100468393  
Rev. A  
August 2007  
Contents  
5.0  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
i
ii  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
1.0  
Introduction  
This manual describes the functional, mechanical and interface specifications for the following Seagate  
Barracuda® ES.2 Serial ATA model drives:  
ST31000340NS  
ST3750330NS  
ST3500320NS  
ST3250310NS  
These drives provide the following key features:  
• 7,200 RPM spindle speed.  
• High instantaneous (burst) data-transfer rates (up to 300 Mbytes per second).  
• Perpendicular recording technology provides the drives with increased areal density.  
• State-of-the-art cache and on-the-fly error-correction algorithms.  
• Native Command Queueing with command ordering to increase performance in demanding applications.  
• Full-track multiple-sector transfer capability without local processor intervention.  
• Quiet operation.  
• SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.  
• Support for S.M.A.R.T. drive monitoring and reporting.  
• Supports latching SATA cables and connectors.  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
1
         
1.1  
About the Serial ATA interface  
The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary  
advantages include:  
• Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jump-  
ers or other configuration options.  
• Thinner and more flexible cabling for improved enclosure airflow and ease of installation.  
• Scalability to higher performance levels.  
In addition, Serial ATA makes the transition from parallel ATA easy by providing legacy software support. Serial  
ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disc drive in your current  
system and expect all of your existing applications to work as normal.  
The Serial ATA interface connects each disc drive in a point-to-point configuration with the Serial ATA host  
adapter. There is no master/slave relationship with Serial ATA devices like there is with parallel ATA. If two  
drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they  
were both “masters” on two separate ports. This essentially means both drives behave as if they are Device 0  
(master) devices.  
Note. The host adapter may, optionally, emulate a master/slave environment to host software where two  
devices on separate Serial ATA ports are represented to host software as a Device 0 (master) and  
Device 1 (slave) accessed at the same set of host bus addresses. A host adapter that emulates a  
master/slave environment manages two sets of shadow registers. This is not a typical Serial ATA  
environment.  
The Serial ATA host adapter and drive share the function of emulating parallel ATA device behavior to provide  
backward compatibility with existing host systems and software. The Command and Control Block registers,  
PIO and DMA data transfers, resets, and interrupts are all emulated.  
The Serial ATA host adapter contains a set of registers that shadow the contents of the traditional device regis-  
ters, referred to as the Shadow Register Block. All Serial ATA devices behave like Device 0 devices. For addi-  
tional information about how Serial ATA emulates parallel ATA, refer to the “Serial ATA: High Speed Serialized  
2
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
       
2.0  
Drive specifications  
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal  
power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the  
following drive models:  
ST31000340NS  
ST3750330NS  
ST3500320NS  
ST3250310NS  
2.1  
Specification summary tables  
The specifications listed in the following tables are for quick reference. For details on specification measure-  
ment or definition, see the appropriate section of this manual.  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
3
       
Table 1:  
Drive specifications summary for 1000 GB (1 Tbyte) and 750 GB models  
Drive specification  
ST31000340NS  
ST3750330NS  
Formatted Gbytes (512 bytes/sector)*  
Guaranteed sectors  
1000  
750  
1,953,525,168  
1,465,149,168  
Heads  
8
6
3
Discs  
4
Bytes per sector  
512  
63  
Default sectors per track  
Default read/write heads  
16  
Default cylinders  
16,383  
1,090  
150  
164  
7,200  
1287  
105  
300  
Recording density, KBPI (kbits/in max)  
Track density, KTPI (ktracks/in avg.)  
Areal density, (Gbits/in2 avg)  
Spindle speed (RPM)  
Internal data transfer rate (Mbits/sec max)  
Sustained data transfer rate OD (Mbytes/sec max)  
I/O data-transfer rate (Mbytes/sec max)  
ATA data-transfer modes supported  
PIO modes 0–4  
Multiword DMA modes 0–2  
Ultra DMA modes 0–6  
Cache buffer  
32 Mbytes  
Height (mm max)  
26.1 mm (1.028 inches)  
Width (mm max)  
101.6 mm (4.000 inches) +/- 0.010 inches  
146.99 mm (5.787 inches)  
Length (mm max)  
Weight (max)  
665 grams (1.466 lbs)  
4.16 msec  
20 sec  
630 grams (1.389 lbs)  
Average latency  
Power-on to ready (sec max)  
Standby to ready (sec max)  
Track-to-track seek time (msec typical)  
Average seek, read (msec typical)  
Average seek, write (msec typical)  
Startup current (typical) 12V (peak)  
Voltage tolerance (including noise)  
10 sec  
9 sec  
0.8 read; 1.0 write  
8.5  
9.5  
2.8 amps  
5V + 10% / -7.5%  
12V + 10% / -7.5%  
Ambient temperature  
5° to 55°C (operating)  
–40° to 70°C (nonoperating)  
Temperature gradient (°C per hour max)  
Relative humidity  
20°C (operating)  
30°C (nonoperating)  
5% to 95% (operating)  
5% to 95% (nonoperating)  
Relative humidity gradient  
30% per hour max  
Wet bulb temperature (°C max)  
37.7 (operating)  
40.0 (nonoperating)  
Altitude, operating  
–60.96 m to 3,048 m  
(–200 ft. to 10,000+ ft.)  
Altitude, nonoperating  
(below mean sea level, max)  
–60.96 m to 12,192 m  
(–200 ft. to 40,000+ ft.)  
Operational Shock (max at 2 msec)  
70 Gs  
Non-Operational Shock (max at 2 msec)  
300 Gs  
4
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
Drive specification  
ST31000340NS  
ST3750330NS  
Vibration, operating  
5–22 Hz:  
0.25 Gs, Limited displacement  
22–350 Hz: 0.50 Gs  
350–500 Hz: 0.25 Gs  
Vibration, nonoperating  
5–22 Hz:  
2.0 Gs, Limited displacement  
22–350 Hz: 5.0 Gs  
350–500 Hz: 2.0 Gs  
Drive acoustics, sound power (bels)  
Active  
3.25 (typical)  
3.4 (max)  
Idle**  
2.7 (typical)  
2.9 (max)  
Performance seek  
Quiet seek  
3.05 (typical)  
3.2 (max)  
2.95 (typical)  
3.1 (max)  
Nonrecoverable read errors  
Annualized Failure Rate (AFR)  
Warranty  
1 sector per 1015 bits read  
0.73%  
5 years on distribution units.  
To determine the warranty for a specific drive, use a web browser to access  
the following web page: www.seagate.com/support/service/  
From this page, click on the “Verify Your Warranty” link. You will be asked to  
provide the drive serial number, model number (or part number) and country  
of purchase. The system will display the warranty information for your drive.  
Contact start-stop cycles  
(25°C, 50% rel. humidity)  
50,000  
Supports Hotplug operation per  
Yes  
Serial ATA Revision 2.5 specification  
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment  
and formatting.  
**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
5
Table 2:  
Drive specifications summary for 500 GB and 250 GB models  
Drive specification  
ST3500320NS  
ST3250310NS  
Formatted Gbytes (512 bytes/sector)*  
Guaranteed sectors  
500  
250  
976,773,168  
4
488,397,168  
Heads  
2
1
Discs  
2
Bytes per sector  
512  
Default sectors per track  
63  
Default read/write heads  
16  
Default cylinders  
16,383  
1,090  
150  
Recording density, KBPI (kbits/in max)  
Track density, KTPI (ktracks/in avg.)  
Areal density, (Gbits/in2 avg)  
Spindle speed (RPM)  
164  
7,200  
1287  
105  
Internal data transfer rate (Mbits/sec max)  
Sustained data transfer rate OD (Mbytes/sec max)  
I/O data-transfer rate (Mbytes/sec max)  
ATA data-transfer modes supported  
300  
PIO modes 0–4  
Multiword DMA modes 0–2  
Ultra DMA modes 0–6  
Cache buffer  
32 Mbytes  
Height (mm max)  
26.1 mm (1.028 inches)  
Width (mm max)  
101.6 mm (4.000 inches) +/- 0.010 inches  
146.99 mm (5.787 inches)  
Length (mm max)  
Weight (max)  
530 grams (1.168 lbs)  
495 grams (1.091 lbs)  
Average latency  
4.16 msec  
20 sec  
Power-on to ready (sec max)  
Standby to ready (sec max)  
Track-to-track seek time (msec typical)  
Average seek, read (msec typical)  
Average seek, write (msec typical)  
Startup current (typical) 12V (peak)  
Voltage tolerance (including noise)  
8 sec  
0.8 read; 1.0 write  
8.5  
9.5  
2.8 amps  
5V + 10% / -7.5%  
12V + 10% / -7.5%  
Ambient temperature  
5° to 55°C (operating)  
–40° to 70°C (nonoperating)  
Temperature gradient (°C per hour max)  
Relative humidity  
20°C (operating)  
30°C (nonoperating)  
5% to 95% (operating)  
5% to 95% (nonoperating)  
Relative humidity gradient  
30% per hour max  
Wet bulb temperature (°C max)  
37.7 (operating)  
40.0 (nonoperating)  
Altitude, operating  
–60.96 m to 3,048 m  
(–200 ft. to 10,000+ ft.)  
Altitude, nonoperating  
(below mean sea level, max)  
–60.96 m to 12,192 m  
(–200 ft. to 40,000+ ft.)  
Operational Shock (max at 2 msec)  
70 Gs  
Non-Operational Shock (max at 2 msec)  
300 Gs  
6
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
Drive specification  
ST3500320NS  
ST3250310NS  
Vibration, operating  
5–22 Hz:  
0.25 Gs, Limited displacement  
22–350 Hz: 0.50 Gs  
350–500 Hz: 0.25 Gs  
Vibration, nonoperating  
5–22 Hz:  
2.0 Gs, Limited displacement  
22–350 Hz: 5.0 Gs  
350–500 Hz: 2.0 Gs  
Drive acoustics, sound power (bels)  
Active  
3.25 (typical)  
3.4 (max)  
Idle**  
2.5 (typical)  
2.7 (max)  
Performance seek  
Quiet seek  
2.85 (typical)  
3.0 (max)  
2.75 (typical)  
2.9 (max)  
Nonrecoverable read errors  
Annualized Failure Rate (AFR)  
Warranty  
1 sector per 1015 bits read  
0.73%  
5 years on distribution units.  
To determine the warranty for a specific drive, use a web browser to  
access the following web page: www.seagate.com/support/service/  
From this page, click on the “Verify Your Warranty” link. You will be asked  
to provide the drive serial number, model number (or part number) and  
country of purchase. The system will display the warranty information for  
your drive.  
Contact start-stop cycles  
(25°C, 50% rel. humidity)  
50,000  
Supports Hotplug operation per  
Yes  
Serial ATA Revision 2.5 specification  
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment  
and formatting.  
**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
7
2.2  
Formatted capacity  
Formatted  
capacity*  
Guaranteed  
sectors  
Model  
Bytes per sector  
ST31000340NS  
ST3750330NS  
ST3500320NS  
ST3250310NS  
1000 Gbytes  
750 Gbytes  
500 Gbytes  
250 Gbytes  
1,953,525,168  
1,465,149,168  
976,773,168  
488,397,168  
512  
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment  
and formatting.  
2.2.1  
LBA mode  
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,  
where n is the number of guaranteed sectors as defined above.  
See Section 4.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48-  
bit addressing support of drives with capacities over 137 Gbytes.  
2.3  
Default logical geometry  
Cylinders  
Read/write heads  
Sectors per track  
63  
16,383  
16  
LBA mode  
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,  
where n is the number of guaranteed sectors as defined above.  
8
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
                             
2.4  
Recording and interface technology  
1000GB  
750GB  
500GB  
250GB  
Interface  
Serial ATA (SATA)  
Recording method  
Perpendicular  
Recording density, KBPI (kbits/inch max)  
Track density, KTPI (ktracks/inch avg)  
1,090  
150  
2
Areal density (Gbits/inch avg)  
164  
Spindle speed (RPM) (± 0.2%)  
7,200  
Internal data transfer rate (Mbits/sec max)  
Sustained data transfer rate (Mbytes/sec max)  
I/O data-transfer rate (Mbytes/sec max)  
1287  
105  
300 (Ultra DMA mode 5)  
2.5  
Physical characteristics  
Maximum height  
26.1 mm (1.028 inches)  
Maximum width  
Maximum length  
Max weight  
101.6 mm (4.000 +/- 0.010 inches)  
146.99 mm (5.787 inches)  
ST31000340NS  
665 grams (1.466 lbs)  
630 grams (1.389 lbs)  
530 grams (1.168 lbs)  
495 grams (1.091 lbs)  
32 Mbytes (16,384 kbytes)  
ST3750330NS  
ST3500320NS  
ST3250310NS  
Cache buffer  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
9
                                       
2.6  
Seek time  
Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using  
drive diagnostics. The specifications in the table below are defined as follows:  
• Track-to-track seek time is an average of all possible single-track seeks in both directions.  
• Average seek time is a true statistical random average of at least 5,000 measurements of seeks between  
random tracks, less overhead.  
*Typical seek times (msec)  
Track-to-track  
Read  
0.8  
Write  
1.0  
Average  
8.5  
9.5  
Average latency:  
4.16  
*Measured in performance mode.  
Note. These drives are designed to consistently meet the seek times represented in this manual. Physical  
seeks, regardless of mode (such as track-to-track and average), are expected to meet the noted  
values. However, due to the manner in which these drives are formatted, benchmark tests that  
include command overhead or measure logical seeks may produce results that vary from these  
specifications.  
2.7  
Start/stop times  
ST31000340NS  
20 (max)  
ST3750330NS  
9 (max)  
ST3500320NS, ST3250310NS  
8 (max)  
Power-on to Ready (sec)  
Standby to Ready (sec)  
10 (max)  
Ready to spindle stop (sec)  
20 (max)  
10  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
                               
2.8  
Power specifications  
The drive receives DC power (+5V or +12V) through a native SATA power connector. See Figure 4 on page 24.  
2.8.1 Power consumption  
Power requirements for the drives are listed in the table on page 9. Typical power measurements are based on  
an average of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient  
temperature.  
• Spinup power  
Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating  
speed.  
• Seek mode  
During seek mode, the read/write actuator arm moves toward a specific position on the disc surface and  
does not execute a read or write operation. Servo electronics are active. Seek mode power represents the  
worst-case power consumption, using only random seeks with read or write latency time. This mode is not  
typical and is provided for worst-case information.  
• Read/write power and current  
Read/write power is measured with the heads on track, based on a 16-sector write followed by a 32-msec  
delay, then a 16-sector read followed by a 32-msec delay.  
• Operating power and current  
Operating power is measured using 40 percent random seeks, 40 percent read/write mode (1 write for each  
10 reads) and 20 percent drive idle mode.  
• Idle mode power  
Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in  
a random track location.  
• Standby mode  
During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/  
write electronics are in power-down mode.  
Table 3:  
DC power requirements  
Power dissipation (4-disc values shown)  
Avg (watts 25° C)  
Avg 5V typ amps  
Avg 12V typ amps  
2.80 (peak)  
0.530  
Spinup  
Idle*  
7.96  
9.29  
11.16  
10.42  
0.99  
0.99  
0.320  
Idle* (with offline activity)  
Operating (40% r/w, 40% seek, 20% inop.)  
Seeking (random, 20% idle)  
Standby  
0.610  
0.520  
0.600  
0.680  
0.500  
0.660  
0.150  
0.020  
Sleep  
0.150  
0.020  
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
11  
                                                           
2.8.1.1  
Typical current profiles  
Figure 1. Typical 5V startup and operation current profile  
12  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
 
Figure 2. Typical 12V startup and operation current profile  
2.8.2 Conducted noise  
Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on  
the +12 volt line or an equivalent 15-ohm resistive load on the +5 volt line.  
• Using 12-volt power, the drive is expected to operate with a maximum of 120 mV peak-to-peak square-wave  
injected noise at up to 10 MHz.  
• Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave  
injected noise at up to 10 MHz.  
Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write  
current.  
2.8.3  
Voltage tolerance  
Voltage tolerance (including noise):  
5V +10% / -7.5%  
12V +10% / -7.5%  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
13  
               
2.8.4  
Power-management modes  
The drive provides programmable power management to provide greater energy efficiency. In most systems,  
you can control power management through the system setup program. The drive features the following  
power-management modes:  
Power modes  
Active  
Heads  
Spindle  
Rotating  
Rotating  
Stopped  
Stopped  
Buffer  
Tracking  
Tracking  
Parked  
Parked  
Enabled  
Enabled  
Enabled  
Disabled  
Idle  
Standby  
Sleep  
Active mode  
The drive is in Active mode during the read/write and seek operations.  
• Idle mode  
The buffer remains enabled, and the drive accepts all commands and returns to Active mode any time disc  
access is necessary.  
Standby mode  
The drive enters Standby mode when the host sends a Standby Immediate command. If the host has set  
the standby timer, the drive can also enter Standby mode automatically after the drive has been inactive for  
a specifiable length of time. The standby timer delay is established using a Standby or Idle command. In  
Standby mode, the drive buffer is enabled, the heads are parked and the spindle is at rest. The drive  
accepts all commands and returns to Active mode any time disc access is necessary.  
• Sleep mode  
The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive  
buffer is disabled, the heads are parked and the spindle is at rest. The drive leaves Sleep mode after it  
receives a Hard Reset or Soft Reset from the host. After receiving a reset, the drive exits Sleep mode and  
enters Standby mode with all current translation parameters intact.  
• Idle and Standby timers  
Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and  
begins counting down from its specified delay times to zero. If the standby timer reaches zero before any  
drive activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the  
drive accepts all commands and returns to Active mode when disc access is necessary.  
14  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
                             
2.9  
Environmental specifications  
Ambient temperature  
2.9.1  
Ambient temperature is defined as the temperature of the environment immediately surrounding the drive.  
Actual drive case temperature should not exceed 60°C (140°F) within the operating ambient conditions.  
Above 1,000 feet (305 meters), the maximum temperature is derated linearly to 112°F (44°C) at 10,000 feet  
(3,048 meters).  
Operating:  
5° to 55°C (41° to 131°F)  
Nonoperating:  
–40° to 70°C (–40° to 158°F)  
2.9.2  
Temperature gradient  
Operating:  
20°C per hour (68°F per hour max), without condensation  
30°C per hour (86°F per hour max)  
Nonoperating:  
2.9.3  
2.9.3.1  
Humidity  
Relative humidity  
Operating:  
Nonoperating:  
5% to 95% noncondensing (30% per hour max)  
5% to 95% noncondensing (30% per hour max)  
2.9.3.2  
Wet bulb temperature  
Operating:  
37.7°C (99.9°F max)  
40.0°C (104.0°F max)  
Nonoperating:  
2.9.4  
Altitude  
Operating:  
–60.96 m to 3,048 m (–200 ft. to 10,000+ ft.)  
–60.96 m to 12,192 m (–200 ft. to 40,000+ ft.)  
Nonoperating:  
2.9.5  
Shock  
All shock specifications assume that the drive is mounted securely with the input shock applied at the drive  
mounting screws. Shock may be applied in the X, Y or Z axis.  
2.9.5.1  
Operating shock  
These drives comply with the performance levels specified in this document when subjected to a maximum  
operating shock of 70 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more  
than two times per second.  
2.9.5.2  
Nonoperating shock  
The nonoperating shock level that the drive can experience without incurring physical damage or degradation  
in performance when subsequently put into operation is 300 Gs based on a nonrepetitive half-sine shock pulse  
of 2 msec duration.  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
15  
                                         
2.9.6  
Vibration  
All vibration specifications assume that the drive is mounted securely with the input vibration applied at the  
drive mounting screws. Vibration may be applied in the X, Y or Z axis.  
2.9.6.1  
Operating vibration  
The maximum vibration levels that the drive may experience while meeting the performance standards speci-  
fied in this document are specified below.  
5–22 Hz  
0.25 Gs (Limited displacement)  
22–350 Hz  
350–500 Hz  
0.50 Gs  
0.25 Gs  
2.9.6.2  
Nonoperating vibration  
The maximum nonoperating vibration levels that the drive may experience without incurring physical damage  
or degradation in performance when subsequently put into operation are specified below.  
5–22 Hz  
2.0 Gs (limited displacement)  
22–350 Hz  
350–500 Hz  
5.0 Gs  
2.0 Gs  
16  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
           
2.10  
Acoustics  
Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea-  
surements are consistent with ISO document 7779. Sound power measurements are taken under essentially  
free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward.  
Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined  
by the following equation:  
(Number of seeks per second = 0.4 / (average latency + average access time)  
Table 4:  
Fluid Dynamic Bearing (FDB) motor acoustics  
Active  
Idle*  
Performance seek  
Quiet Seek  
ST31000340NS  
ST3750330NS  
ST3500320NS  
ST3250310NS  
2.7 bels (typ)  
2.9 bels (max)  
3.05 bels (typ)  
3.2 bels (max)  
2.95 bels (typ)  
3.1 bels (max)  
3.25 bels (typ)  
3.4 bels (max)  
2.5 bels (typ)  
2.7 bels (max)  
2.85 bels (typ)  
3.0 bels (max)  
2.75 bels (typ)  
2.9 bels (max)  
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
2.11  
Electromagnetic immunity  
When properly installed in a representative host system, the drive operates without errors or degradation in  
performance when subjected to the radio frequency (RF) environments defined in the following table:  
Table 5:  
Test  
Radio frequency environments  
Description  
Performance level  
Reference standard  
Electrostatic  
discharge  
Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV  
B
EN 61000-4-2: 95  
Radiated RF  
immunity  
80 to 1,000 MHz, 3 V/m,  
A
B
EN 61000-4-3: 96  
ENV 50204: 95  
80% AM with 1 kHz sine  
900 MHz, 3 V/m, 50% pulse modulation @ 200 Hz  
Electrical fast  
transient  
± 1 kV on AC mains, ± 0.5 kV on external I/O  
EN 61000-4-4: 95  
Surge immunity ± 1 kV differential, ± 2 kV common, AC mains  
B
A
EN 61000-4-5: 95  
EN 61000-4-6: 97  
Conducted RF  
immunity  
150 kHz to 80 MHz, 3 Vrms, 80% AM with 1 kHz sine  
Voltage dips,  
interrupts  
0% open, 5 seconds  
0% short, 5 seconds  
40%, 0.10 seconds  
70%, 0.01 seconds  
C
C
C
B
EN 61000-4-11: 94  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
17  
                           
2.12  
Reliability  
2.12.1  
Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)  
The product shall achieve an Annualized Failure Rate - AFR - of 0.73% (Mean Time Between Failures - MTBF  
- of 1.2 Million hrs) when operated in an environment that ensures the HDA case temperatures do not exceed  
50°C. Operation at case temperatures outside the specifications in Section 2.9 may increase the product Annu-  
alized Failure Rate (decrease MTBF). AFR and MTBF are population statistics that are not relevant to individ-  
ual units.  
AFR and MTBF specifications are based on the following assumptions for business critical storage system  
environments:  
• 8,760 power-on-hours per year.  
• 250 average motor start/stop cycles per year.  
• Operations at nominal voltages.  
• Systems will provide adequate cooling to ensure the case temperatures do not exceed 50°C. Temperatures  
outside the specifications in Section 2.9 will increase the product AFR and decrease MTBF.  
15  
Nonrecoverable read errors  
Annualized Failure Rate (AFR)  
Contact start-stop cycles  
1 per 10 bits read, max  
0.73% (nominal power, 50°C case temperature)  
50,000 cycles  
(at nominal voltage and temperature, with 60 cycles per hour and a 50%  
duty cycle)  
Warranty  
5 years on distribution units.  
To determine the warranty for a specific drive, use a web browser to access  
the following web page: www.seagate.com/support/service/  
From this page, click on the “Verify Your Warranty” link. You will be asked to  
provide the drive serial number, model number (or part number) and country  
of purchase. The system will display the warranty information for your drive.  
Preventive maintenance  
None required.  
2.13  
Agency certification  
2.13.1  
Safety certification  
The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections  
of IEC950 and EN 60950 as tested by TUV North America.  
2.13.2  
Electromagnetic compatibility  
Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Elec-  
tromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product  
standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and  
the immunity levels are defined by EN 55024.  
Seagate uses an independent laboratory to confirm compliance with the EC directives specified in the previous  
paragraph. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply  
with the directives when used in the test systems, we cannot guarantee that all systems will comply with the  
directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O  
cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators  
should confirm EMC compliance and provide CE marking for their products.  
18  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
                                                             
Korean RRL  
If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with para-  
graph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic  
Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information  
and Communication Republic of Korea.  
These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibil-  
ity (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recog-  
nized lab.  
• Barracuda ES.2  
• Certificate number:  
1 TB- STX- ST31000340NS (B)  
750 GB- STX- ST31000340NS (B)  
500 GB- STX- ST3500320NS (B)  
250 GB- STX- ST3500320NS (B)  
Australian C-Tick (N176)  
If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZS3548  
1995 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communi-  
cation Authority (ACA).  
2.13.3  
FCC verification  
These drives are intended to be contained solely within a personal computer or similar enclosure (not attached  
as an external device). As such, each drive is considered to be a subassembly even when it is individually mar-  
keted to the customer. As a subassembly, no Federal Communications Commission verification or certification  
of the device is required.  
Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total  
assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B  
computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is  
likely to result in interference to radio and television reception.  
Radio and television interference. This equipment generates and uses radio frequency energy and if not  
installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio  
and television reception.  
This equipment is designed to provide reasonable protection against such interference in a residential installa-  
tion. However, there is no guarantee that interference will not occur in a particular installation. If this equipment  
does cause interference to radio or television, which can be determined by turning the equipment on and off,  
you are encouraged to try one or more of the following corrective measures:  
• Reorient the receiving antenna.  
• Move the device to one side or the other of the radio or TV.  
• Move the device farther away from the radio or TV.  
• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.  
If necessary, you should consult your dealer or an experienced radio/television technician for additional sug-  
gestions. You may find helpful the following booklet prepared by the Federal Communications Commission:  
How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Super-  
intendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication num-  
ber 004-000-00345-4.  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
19  
                             
2.14  
Environmental protection  
Seagate designs its products to meet environmental protection requirements worldwide, including regulations  
restricting certain chemical substances.  
2.14.1  
European Union Restriction of Hazardous Substances (RoHS) Directive  
Seagate designs its products to meet environmental protection requirements worldwide, including regulations  
restricting certain chemical substances. A new law, the European Union Restriction of Hazardous Substances  
(RoHS) Directive, restricts the presence of chemical substances, including Lead, Cadmium, Mercury,  
Hexavalent Chromium, PBB and PBDE, in electronic products, effective July 2006. This drive is manufactured  
with components and materials that comply with the RoHS Directive.  
2.14.2  
2.14.2  
China Restriction of Hazardous Substances (RoHS) Directive  
中国限制危险物品的指令  
This product has an Environmental Protection Use Period (EPUP) of 20 years. The following  
table contains information mandated by China's "Marking Requirements for Control of Pollution  
Caused by Electronic Information Products" Standard.  
"O" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is lower  
than the threshold defined by the China RoHS MCV Standard.  
O"表示该部件(于同类物品程度上)所含的危险和有毒物质低于中国RoHS MCV标准所定义的门槛值。  
"X" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is over  
the threshold defined by the China RoHS MCV Standard.  
X "表示该部件(于同类物品程度上)所含的危险和有毒物质超出中国RoHS MCV标准所定义的门槛值。  
2.15  
Corrosive environment  
Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to  
light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM  
B845. However, this accelerated testing cannot duplicate every potential application environment. Users  
should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive  
chemicals as electronic drive component reliability can be affected by the installation environment. The silver,  
copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chlo-  
ride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components  
should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or  
20  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
               
exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulca-  
nized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any  
electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
21  
22  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
3.0  
Configuring and mounting the drive  
This section contains the specifications and instructions for configuring and mounting the drive.  
3.1  
Handling and static-discharge precautions  
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis-  
charge (ESD) hazards. Observe the following standard handling and static-discharge precautions:  
Caution:  
• Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal  
chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire  
installation procedure.  
• Handle the drive by its edges or frame only.  
• The drive is extremely fragile—handle it with care. Do not press down on the drive top cover.  
• Always rest the drive on a padded, antistatic surface until you mount it in the computer.  
• Do not touch the connector pins or the printed circuit board.  
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids  
the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are  
used to seal out dirt and contamination.  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
23  
                   
3.2  
Configuring the drive  
Each drive on the Serial ATA interface connects point-to-point with the Serial ATA host adapter. There is no  
master/slave relationship because each drive is considered a master in a point-to-point relationship. If two  
drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they  
were both “masters” on two separate ports. Both drives behave as if they are Device 0 (master) devices.  
Serial ATA drives are designed for easy installation. It is usually not necessary to set any jumpers on the drive  
for proper operation; however, if you connect the drive and receive a “drive not detected” error, your SATA-  
equipped motherboard or host adapter may use a chipset that does not support SATA speed autonegotiation. If  
you have a motherboard or host adapter that does not support autonegotiation:  
• Install a jumper as shown in Figure 3 below to limit the data transfer rate to 1.5 Gbits per second (and leave  
the drive connected to the SATA-equipped motherboard or host adapter that doesn’t support autonegotiation)  
or  
• Install a SATA host adapter that supports autonegotiation, leave the drive jumper block set to “Normal  
operation” (see Figure 3 below), and connect the drive to that adapter. This option has the benefit of not limiting  
the drive to a 1.5 Gbits/sec transfer rate.  
3.0 Gbits per second operation  
Limit data transfer rate to  
1.5 Gbits per second  
Jumper block  
SATA interface connector  
Figure 3. Serial ATA connectors  
SATA power connector  
3.3  
Serial ATA cables and connectors  
The Serial ATA interface cable consists of four conductors in two differential pairs, plus three ground connec-  
tions. The cable size may be 30 to 26 AWG with a maximum length of one meter (39.37 inches). See Table 6  
for connector pin definitions. Either end of the SATA signal cable can be attached to the drive or host.  
For direct backplane connection, the drive connectors are inserted directly into the host receptacle. The drive  
and the host receptacle incorporate features that enable the direct connection to be hot pluggable and blind  
mateable.  
For installations which require cables, you can connect the drive as illustrated in Figure 4.  
Signal connector  
Power connector  
Signal cable  
Power cable  
Figure 4. Attaching SATA cabling  
Each cable is keyed to ensure correct orientation. Barracuda ES.2 Serial ATA drives support latching SATA  
connectors.  
24  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
             
3.4  
Drive mounting  
You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the  
bottom-mounting holes. See Figure 5 for drive mounting dimensions. Follow these important mounting precau-  
tions when mounting the drive:  
• Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.  
• Use only 6-32 UNC mounting screws.  
• The screws should be inserted no more than 0.150 inch (3.81 mm) into the bottom or side mounting holes.  
• Do not overtighten the mounting screws (maximum torque: 6 inch-lb).  
Recommended  
case temperature  
measurement location  
[1]  
5.787 (146.9898) max.  
.250 + .015  
(6.35 + .381)  
(3x both sides)  
1.638  
(41.605)  
1.122  
+ .020  
(28.499  
+ .508)  
[1]  
[1]  
4.000  
(101.60)  
[1]  
4.000  
(101.6)  
1.028 max  
(26.111 max)  
[1]  
.138  
(3.505)  
.814  
(20.676)  
C of conn. Datum B  
L
2.00  
Notes:  
(50.80)  
Dimensions are shown in inches (mm).  
[1] Dimensions per SFF-8301 specification  
C of drive  
L
[1]  
2 x 3.750  
(2 x 95.25)  
2 x 1.625  
(2 x 41.28)  
[1]  
[1]  
2 x 1.750  
(2 x 44.45)  
4.000  
(101.6)  
[1]  
Recommended  
case temperature  
measurement location  
Figure 5. Mounting dimensions—top, side and end view  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
25  
       
26  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
4.0  
Serial ATA (SATA) interface  
These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA  
programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6.  
For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT  
Attachment” specification.  
4.1  
Hot-Plug compatibility  
Barracuda ES.2 Serial ATA drives incorporate connectors which enable you to hot plug these drives in accor-  
dance with the Serial ATA II: Extension to Serial ATA 1.0a specification. This specification can be downloaded  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
27  
         
4.2  
Serial ATA device plug connector pin definitions  
Table 6 summarizes the signals on the Serial ATA interface and power connectors.  
Table 6: Serial ATA connector pin definitions  
Segment Pin  
Function  
Ground  
A+  
Definition  
S1  
S2  
S3  
S4  
S5  
S6  
2nd mate  
Differential signal pair A from Phy  
A-  
Ground  
B-  
2nd mate  
Differential signal pair B from Phy  
B+  
Signal  
S7  
Ground  
2nd mate  
Key and spacing separate signal and power segments  
P1  
V33  
3.3V power  
P2  
V33  
3.3V power  
P3  
V33  
3.3V power, pre-charge, 2nd mate  
1st mate  
P4  
Ground  
Ground  
Ground  
V5  
P5  
2nd mate  
P6  
2nd mate  
P7  
5V power, pre-charge, 2nd mate  
5V power  
P8  
V5  
Power  
P9  
V5  
5V power  
P10  
P11  
P12  
P13  
P14  
P15  
Ground  
2nd mate  
Ground or LED signal If grounded, drive does not use deferred spin  
Ground  
V12  
1st mate.  
12V power, pre-charge, 2nd mate  
12V power  
V12  
V12  
12V power  
Notes:  
1. All pins are in a single row, with a 1.27 mm (0.050”) pitch.  
2. The comments on the mating sequence apply to the case of backplane blindmate connector only. In this  
case, the mating sequences are:  
• the ground pins P4 and P12.  
• the pre-charge power pins and the other ground pins.  
• the signal pins and the rest of the power pins.  
3. There are three power pins for each voltage. One pin from each voltage is used for pre-charge when  
installed in a blind-mate backplane configuration.  
4. All used voltage pins (Vx) must be terminated.  
28  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
   
4.3  
Supported ATA commands  
The following table lists Serial ATA standard commands that the drive supports. For a detailed description of  
the ATA commands, refer to the Serial ATA: High Speed Serialized AT Attachment specification. See  
“S.M.A.R.T. commands” on page 36.for details and subcommands used in the S.M.A.R.T. implementation.  
Table 7:  
Supported ATA commands  
Command name  
Command code (in hex)  
98 or E5  
Check Power Mode  
Device Configuration Freeze Lock  
Device Configuration Identify  
Device Configuration Restore  
Device Configuration Set  
Device Reset  
H
H
B1 / C1  
H
H
B1 / C2  
H
H
H
H
B1 / C0  
H
B1 / C3  
H
08  
92  
90  
H
H
H
Download Microcode  
Execute Device Diagnostics  
Flush Cache  
E7  
H
Flush Cache Extended  
Format Track  
EA  
H
50  
H
Identify Device  
EC  
H
Idle  
97 or E3  
H
H
Idle Immediate  
95 or E1  
H
H
Initialize Device Parameters  
Read Buffer  
91  
H
E4  
H
Read DMA  
C8  
H
Read DMA Extended  
Read DMA Without Retries  
Read Log Ext  
25  
H
C9  
H
H
2F  
Read Multiple  
C4  
H
Read Multiple Extended  
Read Native Max Address  
Read Native Max Address Extended  
Read Sectors  
29  
H
F8  
H
H
H
H
H
H
H
H
H
27  
20  
24  
21  
40  
42  
41  
10  
Read Sectors Extended  
Read Sectors Without Retries  
Read Verify Sectors  
Read Verify Sectors Extended  
Read Verify Sectors Without Retries  
Recalibrate  
Security Disable Password  
Security Erase Prepare  
F6  
F3  
H
H
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
29  
                                                                         
Command name  
Security Erase Unit  
Security Freeze  
Security Set Password  
Security Unlock  
Seek  
Command code (in hex)  
F4  
F5  
F1  
F2  
H
H
H
H
H
70  
Set Features  
EF  
H
Set Max Address  
F9  
H
Note: Individual Set Max Address  
commands are identified by the value  
placed in the Set Max Features regis-  
ter as defined to the right.  
Address:  
Password:  
Lock:  
00  
01  
02  
03  
04  
H
H
H
H
H
Unlock:  
Freeze Lock:  
Set Max Address Extended  
Set Multiple Mode  
37  
H
C6  
H
Sleep  
99 or E6  
H
H
S.M.A.R.T. Disable Operations  
S.M.A.R.T. Enable/Disable Autosave  
S.M.A.R.T. Enable Operations  
S.M.A.R.T. Execute Offline  
S.M.A.R.T. Read Attribute Thresholds  
S.M.A.R.T. Read Data  
S.M.A.R.T. Read Log Sector  
S.M.A.R.T. Return Status  
S.M.A.R.T. Save Attribute Values  
S.M.A.R.T. Write Log Sector  
Standby  
B0 / D9  
H
H
B0 / D2  
H
H
H
H
H
H
H
B0 / D8  
H
B0 / D4  
H
B0 / D1  
H
B0 / D0  
H
B0 / D5  
H
B0 / DA  
H
H
H
H
B0 / D3  
H
B0 / D6  
H
96 or E2  
H
H
H
Standby Immediate  
94 or E0  
H
Write Buffer  
E8  
H
Write DMA  
CA  
H
Write DMA Extended  
35  
H
Write DMA FUA Extended  
Write DMA Without Retries  
Write Log Extended  
CD  
H
H
CB  
3F  
H
Write Multiple  
C5  
H
Write Multiple Extended  
Write Multiple FUA Extended  
Write Sectors  
39  
H
CE  
H
30  
31  
34  
H
Write Sectors Without Retries  
Write Sectors Extended  
H
H
30  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
                                                                   
4.3.1  
Identify Device command  
The Identify Device command (command code EC ) transfers information about the drive to the host following  
H
power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table 7 on  
page 29. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or  
vary with the state of the drive. See Section 2.0 on page 3 for default parameter settings.  
The following commands contain drive-specific features that may not be included in the Serial ATA  
specification.  
Word  
Description  
Value  
0C5A  
Configuration information:  
• Bit 15: 0 = ATA; 1 = ATAPI  
• Bit 7: removable media  
• Bit 6: removable controller  
• Bit 0: reserved  
H
0
1
Number of logical cylinders  
16,383  
2
ATA-reserved  
0000  
16  
H
3
Number of logical heads  
4
Retired  
0000  
0000  
H
5
Retired  
H
6
Number of logical sectors per logical track: 63  
Retired  
003F  
H
H
7–9  
10–19  
20  
0000  
Serial number: (20 ASCII characters, 0000 = none)  
ASCII  
H
Retired  
Retired  
Obsolete  
0000  
0400  
0000  
x.xx  
H
H
H
21  
22  
23–26  
Firmware revision (8 ASCII character string, padded with blanks to end  
of string)  
27–46  
47  
Drive model number: (40 ASCII characters, padded with blanks to end  
of string)  
(Bits 7–0) Maximum sectors per interrupt on Read multiple and Write  
multiple (16)  
8010  
0000  
H
48  
Reserved  
H
49  
Standard Standby timer, IORDY supported and may be disabled  
ATA-reserved  
2F00  
H
H
H
H
H
50  
0000  
0200  
0200  
0007  
51  
PIO data-transfer cycle timing mode  
Retired  
52  
53  
Words 54–58, 64–70 and 88 are valid  
Number of current logical cylinders  
Number of current logical heads  
Number of current logical sectors per logical track  
Current capacity in sectors  
54  
xxxx  
xxxx  
xxxx  
xxxx  
xxxx  
H
55  
H
H
H
H
56  
57–58  
59  
Number of sectors transferred during a Read Multiple or Write Multiple  
command  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
31  
   
Word  
Description  
Value  
60–61  
Total number of user-addressable LBA sectors available  
(see Section 2.2 for related information)  
0FFFFFFFh*  
*Note: The maximum value allowed in this field is: 0FFFFFFFh  
(268,435,455 sectors, 137 Gbytes). Drives with capacities over 137  
Gbytes will have 0FFFFFFFh in this field and the actual number of  
user-addressable LBAs specified in words 100-103. This is required for  
drives that support the 48-bit addressing feature.  
62  
63  
Retired  
0000  
H
Multiword DMA active and modes supported (see note following this  
table)  
xx07  
H
64  
Advanced PIO modes supported (modes 3 and 4 supported)  
Minimum multiword DMA transfer cycle time per word (120 nsec)  
Recommended multiword DMA transfer cycle time per word (120 nsec)  
Minimum PIO cycle time without IORDY flow control (240 nsec)  
Minimum PIO cycle time with IORDY flow control (120 nsec)  
ATA-reserved  
0003  
0078  
0078  
H
H
H
65  
66  
67  
00F0  
H
H
H
H
68  
0078  
0000  
0000  
69–74  
75  
Queue depth  
76  
Serial ATA capabilities  
xxxx  
xxxx  
xxxx  
xxxx  
H
77  
Reserved for future Serial ATA definition  
Serial ATA features supported  
H
H
H
78  
79  
Serial ATA features enabled  
80  
Major version number  
003E  
H
81  
Minor version number  
0000  
H
82  
Command sets supported  
364B  
H
83  
Command sets supported  
7C03  
H
84  
Command sets support extension  
Command sets enabled  
4003  
H
85  
30xx  
H
86  
Command sets enabled  
0001  
4000  
H
H
H
87  
Command sets enable extension  
Ultra DMA support and current mode (see note following this table)  
Security erase time  
88  
xx3F  
89  
0000  
0000  
H
H
90  
Enhanced security erase time  
92  
Master password revision code  
FFFE  
H
93  
Hardware reset value (see description following this table)  
ATA-reserved  
xxxx  
H
95–99  
0000  
H
100–  
103  
Total number of user-addressable LBA sectors available (see Section  
2.2 for related information). These words are required for drives that  
support the 48-bit addressing feature. Maximum value:  
0000FFFFFFFFFFFFh.  
1000 GB models = 1,953,525,168  
750 GB models = 1,465,149,168  
500 GB models = 976,773,168  
250 GB models = 488,397,168  
104–  
127  
ATA-reserved  
0000  
H
128  
Security status  
0001  
H
32  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
Word  
Description  
Value  
xxxx  
129–  
159  
Seagate-reserved  
H
160–  
254  
ATA-reserved  
Integrity word  
0000  
xxA5  
H
H
255  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
33  
Note. See the bit descriptions below for words 63, 88, and 93 of the Identify Drive data.  
Description (if bit is set to 1)  
Bit  
0
Word 63  
Multiword DMA mode 0 is supported.  
Multiword DMA mode 1 is supported.  
Multiword DMA mode 2 is supported.  
Multiword DMA mode 0 is currently active.  
Multiword DMA mode 1 is currently active.  
Multiword DMA mode 2 is currently active.  
Word 88  
1
2
8
9
10  
Bit  
0
Ultra DMA mode 0 is supported.  
Ultra DMA mode 1 is supported.  
Ultra DMA mode 2 is supported.  
Ultra DMA mode 3 is supported.  
Ultra DMA mode 4 is supported.  
Ultra DMA mode 5 is supported.  
Ultra DMA mode 6 is supported.  
Ultra DMA mode 0 is currently active.  
Ultra DMA mode 1 is currently active.  
Ultra DMA mode 2 is currently active.  
Ultra DMA mode 3 is currently active.  
Ultra DMA mode 4 is currently active.  
Ultra DMA mode 5 is currently active.  
Ultra DMA mode 6 is currently active.  
1
2
3
4
5
6
8
9
10  
11  
12  
13  
14  
34  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
4.3.2  
Set Features command  
This command controls the implementation of various features that the drive supports. When the drive receives  
this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an inter-  
rupt. If the value in the register does not represent a feature that the drive supports, the command is aborted.  
Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the  
Features register are defined as follows:  
Table 8:  
Set Features command values  
02  
03  
Enable write cache (default).  
H
H
Set transfer mode (based on value in Sector Count register).  
Sector Count register values:  
00 Set PIO mode to default (PIO mode 2).  
H
01 Set PIO mode to default and disable IORDY (PIO mode 2).  
H
08 PIO mode 0  
H
09 PIO mode 1  
H
0A PIO mode 2  
H
0B PIO mode 3  
H
0C PIO mode 4 (default)  
H
20 Multiword DMA mode 0  
H
21 Multiword DMA mode 1  
H
22 Multiword DMA mode 2  
H
40 Ultra DMA mode 0  
H
41 Ultra DMA mode 1  
H
42 Ultra DMA mode 2  
H
43 Ultra DMA mode 3  
H
44 Ultra DMA mode 4  
H
45 Ultra DMA mode 5  
H
46 Ultra DMA mode 6  
H
10  
55  
82  
90  
Enable use of SATA features  
H
H
H
H
Disable read look-ahead (read cache) feature.  
Disable write cache  
Disable use of SATA features  
AA  
Enable read look-ahead (read cache) feature (default).  
Report full capacity available  
H
F1  
H
Note. At power-on, or after a hardware or software reset, the default values of the features are as indi-  
cated above.  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
35  
 
4.3.3  
S.M.A.R.T. commands  
S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive moni-  
tors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines  
that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable.  
S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.  
commands and implementation, see the Draft ATA-5 Standard.  
SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4 ) that elimi-  
H
nates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at:  
This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that  
supports S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the  
drive uses.  
Table 9:  
S.M.A.R.T. commands  
Code in features register  
S.M.A.R.T. command  
D0  
D2  
D3  
D4  
D5  
D6  
D8  
D9  
S.M.A.R.T. Read Data  
H
H
H
H
H
H
H
H
S.M.A.R.T. Enable/Disable Attribute Autosave  
S.M.A.R.T. Save Attribute Values  
S.M.A.R.T. Execute Off-line Immediate (runs DST)  
S.M.A.R.T. Read Log Sector  
S.M.A.R.T. Write Log Sector  
S.M.A.R.T. Enable Operations  
S.M.A.R.T. Disable Operations  
S.M.A.R.T. Return Status  
DA  
H
Note. If an appropriate code is not written to the Features Register, the command is aborted and 0x04  
(abort) is written to the Error register.  
36  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
 
5.0  
Seagate Technology support services  
Online services  
Internet  
For information regarding Seagate products and services, visit www.seagate.com. Worldwide support is  
available 24 hours daily by email for your questions.  
Presales Support:  
Technical Support:  
Warranty Support:  
mySeagate  
my.seagate.com is the industry's first Web portal designed specifically for OEMs and distributors. It provides  
self-service access to critical applications, personalized content and the tools that allow our partners to  
manage their Seagate account functions. Submit pricing requests, orders and returns through a single,  
password-protected Web interface-anytime, anywhere in the world.  
spp.seagate.com  
spp.seagate.com supports Seagate resellers with product information, program benefits and sales tools. You  
may register for customized communications that are not available on the web. These communications contain  
product launch, EOL, pricing, promotions and other channel-related information. To learn more about the  
benefits or to register, go to spp.seagate.com, any time, from anywhere in the world.  
Seagate Service Centers  
Presales Support  
Our Presales Support staff can help you determine which Seagate products are best suited for your specific  
application or computer system, as well as product availability and compatibility.  
Technical Support  
Seagate technical support is available to assist you online at support.seagate.com or through one of our call  
centers. Have your system configuration information and your “ST” model number available.  
SeaTDD(+1-405-324-3655) is a telecommunications device for the deaf (TDD). You can send questions or  
comments 24 hours daily and exchange messages with a technical support specialist during normal business  
hours for the call center in your region.  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
37  
   
Customer Service Operations  
Warranty Service  
Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct  
customers should contact their Seagate Customer Service Operations (CSO) representative for warranty-  
related issues. Resellers or end users of drive products should contact their place of purchase or Seagate  
warranty service for assistance. Have your serial number and model or part number available.  
Data Recovery Services  
Seagate offers data recovery services for all formats and all brands of storage media. Our data recovery  
services labs are currently located throughout the world. . Additional information, including an online request  
form and data loss prevention resources, is available at http://services.seagate.com/index.aspx  
Authorized Service Centers  
Seagate Service Centers are available on a global basis for the return of defective products. Contact your  
customer support representative for the location nearest you.  
USA/Canada/Latin America support services  
For an extensive list of telephone numbers to technical support, presales and warranty service in USA/  
Canada/Latin America, including business hours, go to the "Contact Us" page on www.seagate.com.  
Global Customer Support  
Presales, Technical, and Warranty Support  
Call Center  
USA, Canada,  
and Mexico  
Toll-free  
Direct dial  
1-800-SEAGATE  
+1-405-324-4700  
Data Recovery Services  
Call Center  
Toll-free  
Direct dial  
FAX  
USA, Canada,  
and Mexico  
1-800-475-01435  
+1-905-474-2162  
1-800-475-0158  
+1-905-474-2459  
Europe, the Middle East and Africa Support Services  
For an extensive list of telephone numbers to technical support, presales and warranty service in Europe, the  
Middle East and Africa, go to the "Contact Us" page on www.seagate.com.  
Asia/Pacific Support Services  
For an extensive list of telephone numbers to technical support, presales and warranty service in Asia/Pacific,  
go to the "Contact Us" page on www.seagate.com.  
38  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
Publication feedback survey  
We are interested in your comments and suggestions regarding this publication. Please take a few minutes to  
participate in our survey at the following URL:  
Thank you for your time and comments.  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
39  
40  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
Device Configuration Freeze Lock 29  
Device Configuration Identify 29  
Device Configuration Restore 29  
Device Configuration Set 29  
Device Reset 29  
dimensions 25  
disc surface 11  
dissipation 11  
Download Microcode 29  
Index  
A
ACA 19  
acceleration 16  
acoustics 17  
Active 14  
Active mode 14  
actuator arm 11  
E
Agency certification 18  
altitude 15  
Ambient temperature 15  
ambient temperature 10, 11  
Annualized Failure Rate (AFR) 18  
areal density 1, 9  
Electrical fast transient 17  
Electromagnetic compatibility 18  
Electromagnetic Compatibility (EMC) 19  
Electromagnetic Compatibility control Regulation 19  
Electromagnetic Compatibility Directive (89/336/EEC)  
ATA commands 29  
Australia/New Zealand Standard AS/NZS3548 1995  
Australian Communication Authority (ACA) 19  
Australian C-Tick 19  
Electromagnetic immunity 17  
Electrostatic discharge 17  
electrostatic discharge (ESD) 23  
EN 55022, Class B 18  
EN 55024 18  
EN 60950 18  
Average latency 10  
Average seek time 10  
Environmental specifications 15  
error-correction algorithms 1  
errors 18  
ESD 23  
B
BPI 9  
buffer 9  
EU RoHS directive 20  
European Union (EU) requirements 18  
Execute Device Diagnostics 29  
C
cables and connectors 24  
cache 9  
capacity 8  
case temperature 15  
CE mark 18  
F
FCC verification 19  
features 1  
Federal Communications Commission 19  
Flush Cache 29  
Flush Cache Extended 29  
Format Track 29  
certification 18  
Check Power Mode 29  
China RoHS directive 20  
Class B computing device 19  
compatibility 18  
Conducted noise 13  
Conducted RF immunity 17  
Configuring the drive 23  
connectors 24  
Formatted capacity 8  
G
geometry 8  
Corrosive environment 20  
CSA C22.2 (950) 18  
cycles 18  
guaranteed sectors 8  
Cylinders 8  
H
Handling precautions 23  
heads 8  
height 9  
D
data-transfer rates 1  
DC power 11  
Default logical geometry 8  
density 9  
humidity 15  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
41  
I
P
I/O data-transfer rate 9  
Physical characteristics 9  
Identify Device 29  
point-to-point 2, 24  
Identify Device command 31  
Idle 14, 29  
Idle Immediate 29  
Power consumption 11  
power consumption 11  
power dissipation 11  
Idle mode 11, 14  
Power modes 14  
IEC950 18  
Power specifications 11  
Power-management modes 14  
Power-on to Ready 10  
precautions 23  
printed circuit board 23  
programmable power management 14  
Information Technology Equipment (ITE) 18  
Initialize Device Parameters 29  
Input noise ripple 13  
input voltage 11  
interface 9, 27  
internal data-transfer rate OD 9  
Q
ISO document 7779 17  
ITE 18  
quick reference 3  
R
K
Radiated RF immunity 17  
Radio and television interference 19  
radio frequency (RF) 17  
random seeks 11  
Korea Ministry of Information and Communication  
(MIC) 19  
Korean RRL 19  
Read Buffer 29  
Read DMA 29  
L
latency 10  
Read DMA Extended 29  
Read DMA without Retries 29  
read errors 18  
latency time 11  
LBA mode 8  
length 9  
Read Log Ext 29  
logical geometry 8  
Read Multiple 29  
Read Multiple Extended 29  
Read Native Max Address 29  
Read Native Max Address Extended 29  
Read Sectors 29  
Read Sectors Extended 29  
Read Sectors Without Retries 29  
Read Verify Sectors 29  
Read Verify Sectors Extended 29  
Read Verify Sectors Without Retries 29  
read/write actuator arm 11  
Read/write heads 8  
M
maintenance 18  
master/slave 2  
maximum temperature 15  
MIC 19  
mounting 25  
mounting screws 15  
mounting the drive 23  
N
Read/write power 11  
Recalibrate 29  
noise 13  
nominal power 10  
recording density 9  
Nonoperating shock 15  
Nonoperating vibration 16  
Nonrecoverable read errors 18  
recording method 9  
Recording technology 9  
relative humidity 15  
Reliability 18  
RMS read/write current 13  
RoHS 20  
O
operating 11  
Operating power 11  
Operating shock 15  
Operating vibration 16  
RRL 19  
42  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
S
T
S.M.A.R.T. Disable Operations 30  
S.M.A.R.T. Enable Operations 30  
S.M.A.R.T. Enable/Disable Autosave 30  
S.M.A.R.T. Execute Offline 30  
S.M.A.R.T. implementation 29  
S.M.A.R.T. Read Attribute Thresholds 30  
S.M.A.R.T. Read Data 30  
S.M.A.R.T. Read Log Sector 30  
S.M.A.R.T. Return Status 30  
S.M.A.R.T. Save Attribute Values 30  
S.M.A.R.T. Write Log sector 30  
Safety certification 18  
SATA 27  
technical support services 37  
temperature 10, 15  
temperature gradient 15  
timer 14  
timers 14  
track density 9  
Track-to-track 10  
Track-to-track seek time 10  
TUV North America 18  
U
UL 1950 18  
screws 15  
sectors 8  
V
Sectors per track 8  
Vibration 16  
Security Disable Password 29  
Security Erase Prepare 29  
Security Erase Unit 30  
Security Freeze 30  
voltage 11  
Voltage dips, interrupts 17  
Voltage tolerance 13  
Security Set Password 30  
Security Unlock 30  
Seek 30  
seek mode 11  
Seek mode power 11  
Seek time 10  
Seeking 11  
Serial ATA (SATA) interface 27  
serial ATA ports 2  
Servo electronics 11  
servo electronics 11  
Set Features 30  
Set Max Address 30  
Set Max Address Extended 30  
Set Multiple Mode 30  
Shock 15  
W
weight 9  
wet bulb temperature 15  
width 9  
Write Buffer 30  
Write DMA 30  
Write DMA Extended 30  
Write DMA FUA Extended 30  
Write DMA Without Retries 30  
Write Log Extended 30  
Write Multiple 30  
Write Multiple Extended 30  
Write Multiple FUA Extended 30  
Write Sectors 30  
Write Sectors Extended 30  
Write Sectors Without Retries 30  
single-track seeks 10  
Sleep 11, 14, 30  
Sleep mode 14  
sound 17  
Specification summary table 3  
spindle speed 9  
Spinup 11  
Spinup power 11  
Standby 11, 14, 30  
Standby Immediate 30  
Standby mode 11, 14  
standby timer 14  
Standby to Ready 10  
Start/stop times 10  
start-stop cycles 18  
static-discharge 23  
support services 37  
Surge immunity 17  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
43  
44  
Barracuda ES.2 Serial ATA Product Manual, Rev. A  
Seagate Technology LLC  
920 Disc Drive, Scotts Valley, California 95066-4544, USA  
Publication Number: 100468393, Rev. A, Printed in U.S.A.  

Uniden TCX950 User Manual
Sony Xperia J ST26i User Manual
Siemens Gigaset 150 User Manual
Seagate Pipeline HD ST1000VM002 User Manual
Seagate Barracuda ST3120811AS User Manual
Samsung GT E2550 User Manual
RCA RP5435 User Manual
Philips CDR 775 User Manual
Philips AZ5160 User Manual
geetek Boost N GT APN Quick Installation Manual