SIIG 04 0288E User Manual

USB 2.0+1394 DV Kit  
Quick Installation Guide  
Introducing the USB 2.0+1394 DV Kit  
The USB 2.0+1394 DV Kit is a complete DV editing kit --  
acombocardwithUSB2.0andFireWire(1394a)interfaces,  
deluxe DV editing software (full DV, AVI, QuickTime,  
Windows Media, RealNetworks, and MPEG2 support)  
and a 1394 6-pin/4-pin DV cable.  
FeaturesandBenefits  
Combo card design adds four USB 2.0 (480 Mbps)  
and three 1394a (400 Mbps) ports into your system.  
Hot-swapping feature allows you to connect/  
disconnectdeviceswithoutfirstturningyoursystem  
off  
USB 2.0 interface  
Adds three external and one internal USB 2.0 ports  
Compliant with USB specification rev. 2.0  
Supports high-speed (480 Mbps), full-speed (12  
Mbps), and low-speed (1.5 Mbps) data transfer  
modes for simultaneous operation of multiple USB  
2.0/1.1 devices  
Note: USB 1.1 devices are limited to USB 1.1 speeds  
evenwhentheyareconnectedtoUSB2.0hostadapter  
or USB 2.0 hubs.  
FireWire (1394a) interface  
Adds two external and one internal FireWire ports  
04-0288E  
1
Board Layout  
1394 Port  
1394 Ports  
USB 2.0 Port  
Power Connector  
(optional)  
USB 2.0  
Ports  
Figure 1. Board Layout  
Note: This power connector (same as the one  
used with your floppy disk drive) is designed  
toprovideadditionalpowertotheboardwhen  
needed. This connection is optional. We  
recommend to connect this power connector  
when the following conditions occur:  
- All ports are used.  
- Device(s) not being detected.  
In case you need to connect this power  
connector, power off your system first before  
making this connection.  
3
Hardware Installation  
General instructions for installing the card are provided  
below. Since the design of computer cases and  
motherboards vary, refer to your computer’s reference  
manual for further information, if needed.  
Static Electricity Discharge may permanently damage  
your system. Discharge any static electricity build up in  
your body by touching your computer’s case for a few  
seconds. Avoid any contact with internal parts and  
handle cards only by their external edges.  
1. Turn OFF the power to your computer.  
2. Unplugthepowercordandremoveyourcomputer's  
cover.  
3. Remove the slot bracket from an available PCI slot.  
4. Carefully align the card to the selected PCI slot push  
the board down firmly, but gently, until it is well  
seated.  
5. Replace the slot bracket's holding screw to secure  
the card.  
6. Replacethecomputercoverandreconnectthepower  
cord.  
Driver Installation  
To ensure proper installation of this board, please follow  
these instructions step-by-step.  
Windows98SE  
1. Install the board, boot up the system, and insert the  
driver CD.  
2. WhenWindowsbootsup,attheAddNewHardware  
Wizard window, click Cancel four times.  
4
3. Click Start, then Run. Type in X:\setup.exe and  
click OK. (Change X: to match your CD-ROM drive  
letter)  
4. Click Next, Next, at the Warning box click OK, then  
click Finish to restart.  
5. When the VIA ...Universal Host Controller is  
detected, click Next.  
6. Choose Search for the best driver... and click Next.  
7. Clear all check boxes, click Next, Next, Next.  
NOTE: If prompted for Windows 98SE Installation  
CD, click OK. Insert this CD and click OK.  
8. Click Finish.  
9. When the VIA ...Universal Host Controller is  
detected, click Next.  
10. Repeat steps 6, 7 and 8.  
11. WhentheUSBEnhancedHostControllerisdetected,  
click Next.  
12. Repeat step 6.  
13. Clear all check boxes, click Next, Next, then Finish.  
14. When the VIA OHCI IEEE 1394 Host Controller is  
detected, click Next.  
15. Repeat steps 6 and 13 to complete the installation.  
WindowsME  
1. Install the board, boot up the system, and insert the  
driver CD.  
2. WhenWindowsbootsup,attheAddNewHardware  
Wizard window, click Cancel. Click No to decline  
restart.  
5
3. Click Start, then Run. Type X:\setup.exe and click  
OK. (Change X: to match your CD-ROM drive  
letter).  
4. Follow the on-screen instructions to install the  
driver. When prompted click Finish to restart.  
5. At the Add New Hardware Wizard, choose  
Automatic search for a better ..., click Next, then  
click Finish.  
6. Click Yes to restart Windows to complete.  
Windows2000  
Windows 2000 Service Pack 3 (SP 3) or later is required  
for this installation.  
If you have have Windows 2000 Service Pack 4 (SP4) or  
later installed, Windows will automatically detect and  
installthecorrectdriverforthisboard. Otherwise, follow  
all steps below.  
1. Install the board, boot up the system, and insert the  
driver CD.  
2. When Windows boots up, at the Found New  
Hardware Wizard window, click Cancel.  
3. Click Start, then Run. Type X:\setup.exe and click  
OK. (Change X: to match your CD-ROM drive  
letter).  
4. Click Next, Next to accept the license agreement,  
then Next to install the USB 2.0 driver.  
5. Click Yes to confirm restarting the system  
automatically.  
6. Click Yes to accept Software License Agreement,  
then click OK.  
7. Click the Print to File icon, then click OK.  
6
8. When Windows restarts, the drivers will install  
automatically.  
WindowsXP/Server2003  
Windows XP Service Pack 1 (SP 1) or later is required for  
this installation.  
Windows XP Service Pack 1 or later will automatically  
detect and install the correct drivers for this board.  
Windows2003Serverwillautomaticallydetectandinstall  
the correct drivers for this board.  
ToVerifySuccessfulDriverInstallation  
1. Check Device Manager to verify successful driver  
installation.  
Windows 98SE/ME: From the main desktop, right  
click My Computer, then click Properties. Click  
Device Manager tab.  
Windows 2000/XP/Server 2003: Right click My  
Computer, then click Manage. Click Device  
Manager.  
2. The drivers for this controller show up differently  
under different versions of Windows. Please refer  
to the correct Windows version to verify.  
Windows 98SE/ME/2000 (with sp3):  
a) Under the Universal Serial Bus Controllers:  
- VIA PCI to USB Enhanced Host Controller  
- USB 2.0 Root Hub  
- VIA ... USB Universal Host Controller  
- VIA ... USB Universal Host Controller  
- USB Root Hub  
- USB Root Hub  
7
b) Under the 1394 Bus Controller or IEEE 1394 Bus  
host controllers:  
- VIAOHCICompliantIEEE1394HostController  
Windows 2000 (with SP4 or later):  
a) Under the Universal Serial Bus Controllers:  
- VIA ... Universal Host Controller  
- VIA ... Universal Host Controller  
- VIA USB Enhanced Host Controller  
- USB 2.0 Root Hub  
- USB Root Hub  
- USB Root Hub  
b) Under the IEEE 1394 Bus host controllers:  
- VIAOHCICompliantIEEE1394HostController  
Windows XP (with SP1 or later)/Server 2003:  
a) Under the Universal Serial Bus Controllers:  
- VIA ... USB Universal Host Controller  
- VIA ... USB Universal Host Controller  
- VIA USB Enhanced Host Controller  
- USB Root Hub  
- USB Root Hub  
- USB Root Hub  
b) Under the IEEE 1394 Bus host controllers:  
- VIAOHCICompliantIEEE1394HostController  
8
Ulead VideoStudio Software Installation  
TheUSB2.0+1394DVKitincludesUlead® VideoStudioTM  
digitalvideoeditingsoftwareforproducinghomevideos  
complete with attractive titles, transitions and sounds.  
Before installing VideoStudio, make sure your adapter  
andDVcamcorderareproperlyinstalledandconfigured.  
See next section, Connecting DV Camcorder, for more  
details on how to properly install your DV camcorder.  
1. InserttheUleadVideoStudioDVsoftwareCD. Auto-  
run should start automatically. If not, click Start,  
Run, type in X:\Setup.exe, then click OK. (Change  
X: to match your CD-ROM drive letter).  
2. Select a language, click Next and follow on-screen  
instructions to complete installation.  
Note: For instructions on how to use Ulead  
VideoStudio, please refer to VStudio.pdf file  
located in the Manual directory on the Ulead  
VideoStudio DV software CD.  
Connecting DV Camcorder  
Before setting up the digital video camcorder, make sure  
to verify the driver for the adapter has been successfully  
installed in your system and follow the setup procedures  
listed below.  
1. Boot up your system.  
2. Connect the 4-pin connector of the provided  
FireWire (1394) 6-pin/4-pin DV cable into your  
digital camcorder, and connect the 6-pin connector  
intoanavailableportonthe1394adapter. Poweron  
the camcorder. The camcorder should now appear  
in Device Manager.  
9
ToVerifySuccessfulDVCamcorderSetup  
1. Check Device Manager to verify successful driver  
installation.  
Windows 98SE/ME: From the main desktop, right  
click My Computer, then click Properties. Click  
Device Manager tab.  
Windows 2000/XP/2003: Right click My Computer,  
click Manage, then click Device Manager.  
2. Double click Imaging Device(s).  
- A MicrosoftDVCameraandVCRorDVCamcorder  
should be displayed.  
10  
Technical Support and Warranty  
QUESTIONS?  
SIIG’s Online Support has answers!  
Simply visit our website at www.siig.com and click on Support.  
Our online support database is updated daily with new drivers  
and solutions. Answers to your questions could be just a few clicks  
away. Youcanalsosubmitquestionsonlineandoneofourtechnical  
support analysts will promptly respond.  
Thisproductcomeswithalifetimemanufacturerwarranty. Pleasesee  
SIIGwebsiteformorewarrantydetails. Ifyoushouldhappentohave  
any problems with this product, follow the procedures below.  
A) If it is within the store's return policy period, please return the  
product to the store where you purchased from.  
B) Ifyourpurchasehaspassedthestore'sreturnpolicyperiod,please  
follow these steps to have the product repaired or replaced.  
Step 1: Submit your RMA request.  
Go to www.siig.com, click Support, then RMA to submit a  
request to SIIG RMA. If the product is determined to be  
defective,anRMAnumberwillbeissued. SIIGRMAdepartment  
can also be reached at (510)413-5333.  
Step 2: After obtaining an RMA number, ship the product.  
Properly pack the product for shipping. All software, cable(s)  
and any other accessories that came with the original package  
must be included.  
Clearly write your RMA number on the top of the returned  
package. SIIG will refuse to accept any shipping package, and  
will not be responsible for a product returned without an  
RMA number posted on the outside of the shipping carton.  
You are responsible for the cost of shipping. Ship the product  
to the following address:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538  
RMA#:  
SIIG will ship the repaired or replaced product via Ground  
in the U.S. and International Economy outside of the U.S. at  
no cost to the customer.  
11  
About SIIG, Inc.  
Foundedin1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer  
ofI/Oconnectivityproducts,includingPCI&ISAserialandparallel  
ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b),  
Networking,SoundCards,andotheraccessories. SIIGisthepremier  
one-stop source of upgrades.  
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendly  
features, and are backed by an extensive manufacturer warranty.  
High-quality control standards are evident by the overall ease of  
installation and compatibility of our products, as well as one of the  
lowest defective return rates in the industry. SIIG products can be  
foundincomputerretailstores,mailordercatalogs,ande-commerce  
sitesintheAmericasandtheUK,aswellasthroughmajordistributors,  
system integrators, and VARs.  
PRODUCT NAME  
USB 2.0+FireWire DV Kit  
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS  
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE  
FCCCOMPLIANCESTATEMENT:  
This device complies with part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) This device may not cause  
harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE  
SIIG, Inc.  
6078 Stewart Ave.  
Fremont, CA 94538-3152  
USB 2.0+FireWire DV Kit is a trademark of SIIG, Inc.  
SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are  
registered trademarks of Microsoft Corporation. Pentium is a registered trademark of Intel  
Corporation. Other names used in publication are for identification only and may be trademarks  
oftheirrespectivecompanies.  
October, 2006  
Copyright ©2006 by SIIG, Inc. All rights reserved.  

Teac DV W28SS V User Manual
Sony Xperia ZL 1273 5759 User Manual
Sony USM1GJX User Manual
Sony RCD W50C User Manual
Sony CFD E77L User Manual
Seagate Cheetah 100516226 User Manual
Seagate Backup Plus STCA2000100 User Manual
Samsung SPH SPH A460 User Manual
Sabrent USBDSC5 User Manual
RCA RP5415PK User Manual