Philips HD7811 User Manual

HD7811, HD7810 Coffee Machine  
3
15. Do not use this appliance at altitudes higher than 6800 ft./  
2200m above sea level.  
16. Flush the Coffee Machine with fresh water before using it for  
the first time (See ‘Preparing the machine for use’).This will  
cause the boiler to fill with water; which is essential for the  
machine to work properly.  
17.To prevent scalds and/or property damage, always make sure  
Coffee Machine lid is securely in place and properly locked  
before you start using the machine and during brew cycle. Do  
not force when opening or closing lid.  
18. Do not open lid until Coffee Machine has finished brew cycle.  
Hot steam or hot water trapped under lid cover could burn  
your fingers.  
19.Warning:To reduce the risk of fire or electric shock,  
do not remove the bottom cover. No user serviceable  
parts are inside. Return the Coffee Machine to the  
nearest Authorized Norelco Service Location for  
examination, repair or adjustment.  
SAVETHESE  
INSTRUCTIONS  
SPECIAL INSTRUCTIONS  
This Coffee Machine has a short cord to reduce the hazards of  
becoming entangled in or tripping over a longer cord.An extension  
cord may be used if the rating is equal to or greater than the rating  
of the Coffee Machine. Use an extension cord rated 13 amperes or  
greater. Care must be taken to arrange extension cord so that it  
does not hang over the edge of counter top or table top, where it  
can be pulled on by children or tripped over unintentionally.  
Operating the Coffee Machine and another appliance at the same  
time from the same electrical circuit could cause an electrical  
overload, which would blow the fuse or trip the circuit breaker.  
SPECIAL POLARIZED PLUG  
INSTRUCTIONS  
This Philips Coffee Machine has a polarized plug (one blade is wider  
than the other) as an added safety feature.To reduce the risk of  
electric shock:  
- Plug will fit into polarized outlet only one way.  
- If plug does not properly fit into outlet at first, reverse it.  
- If plug still does not fit, contact a qualified electrician.  
DO NOT ATTEMPTTO DEFEATTHIS  
SAFETY FEATURE IN ANYWAY.  
4
WARNING:  
-To avoid risk of personal injury or damage to property as a result  
of overflow, be sure that the cup or mug is centered under the  
coffee outflow unit during the brew cycle.  
- Brewed coffee and coffee pods are very hot. Handle with care to  
avoid scalding.  
- If coffee outflow unit overflows or fails to drain into cup/mug  
during brewing cycle, do not open lid or handle coffee outflow  
unit or coffee pod holder(s). Unplug Coffee Machine and wait for  
contents to cool before handling.  
- Do not remove any part of Coffee Machine or cup/mug during  
the brew cycle as scalding could occur.  
- Use only fresh, cool water in this appliance. Do not put any other  
liquids in this appliance except as instructed in the ‘Descaling’  
section. Do not refill the water reservoir with hot water or  
coffee.  
- DO NOT attempt to move an appliance containing hot liquids or  
during the brewing process. Allow appliance to cool completely  
before moving.  
- Keep appliance at least 4 inches away from walls or other objects  
while operating. Do not place any object on top of coffee  
machine while operating.  
PLEASE READ AND SAVETHIS  
INSTRUCTION BOOKLET.  
5
TABLE OF CONTENTS  
Features  
6
Introduction  
Preparing the machine for use  
Brewing coffee  
Cleaning  
7
8
10  
12  
13  
14  
15  
15  
17  
Descaling  
Storage  
Assistance  
Trouble shooting guide  
Warranty  
6
HD7810  
HD7811  
Features  
A Water reservoir  
B Reservoir splash guard  
C 1-pod holder; for 1 small cup of coffee (125 ml/app. 4.0 oz)  
D 2-pod holder, for 2 small cups of coffee (125 ml/app. 4.0 oz each)  
or 1 mug of coffee (250 ml/app. 8.0 oz)  
E Coffee outflow unit  
F Cover of coffee outflow unit  
G Drip tray  
H Cup tray  
I Metal distribution disk  
J Sealing ring  
K Outflow valve  
L Indicator light  
7
Introduction  
With the Senseo™ coffee machine by Philips you can enjoy a perfect  
cup of coffee - topped with a rich frothy coffee layer - whenever you  
feel like it. Each cup is freshly brewed, so you're always sure of that  
pure, smooth taste.The patented Senseo brewing system from Philips  
in combination with the special Senseo coffee pods makes sure you get  
only the very best in flavor and aroma from freshly roasted coffee.  
To optimize the taste of the coffee, you should keep the following  
aspects in mind:  
Fresh water  
Use fresh water every day. Before using for the first time or if you have  
not used the machine for some time, rinse the water reservoir, fill it  
with fresh water and flush the machine before you begin brewing  
coffee (see ‘Preparing the machine for use’).  
Senseo coffee pods  
In order to avoid damage, use only Senseo coffee pods that have been  
specifically developed for your Senseo coffee machine for a pure,  
smooth taste.The Senseo coffee pods will stay fresh longer if you close  
the package by means of the keep-fresh seal after use or if you store  
them in a storage container.  
A clean machine  
Scale build-up may cause overheating of the heating element and may  
make the safety cut-out operate prematurely, switching off before the  
water boils. Scale may also reduce the working life of the machine and  
may lengthen the brewing time.  
Clean and descale your Philips Senseo coffee machine regularly (see  
'Cleaning' and 'Descaling'). Remove used coffee pods after brewing. If a  
used pod has been left in the coffee machine and you have not used  
the machine for some time, flush the machine before you use it again  
(see 'Preparing the machine for use').  
8
Preparing the machine for use  
Use this Senseo coffee machine for its intended household use as  
described in this manual.  
YOU CANNOT BREW COFFEE IFYOU HAVE NOT  
FLUSHEDTHE SENSEO COFFEE MACHINE FIRST!  
The flushing cycle causes the boiler to be filled with water.After this  
the coffee machine is ready for use.  
Flush the machine in the following way:  
1
2
3
4
Remove the water reservoir.  
C
C
C
C
Fill the water reservoir with cold water up to the MAX  
indication and put it back into the machine.  
Release the lid by moving the lever upwards.  
Open the lid.  
9
5
6
Put either the 1- or 2-pod holder in the machine without using  
any coffee pod(s).  
C
C
C
C
Close the lid and lock the lever.  
Make sure the lever is properly locked by pushing it down until it snaps  
home with a click.  
Never flush the machine with the lid open!The lid must be properly  
locked.  
B
B
7
Put the plug into a 120V AC electrical outlet.  
8
Put a bowl (with a capacity of at least 1.5 liters/1.6 qt.) under  
the coffee outflow unit to collect the water.  
9
Press on/off button I.Then press both the ° and °°  
buttons briefly at the same time.  
The machine will fill itself with water from the water reservoir.  
This will take some time and you will probably not notice that this  
is happening.After a while, the machine will start flushing and it will  
switch itself off after the flushing cycle. During the flushing cycle  
the machine produces more noise than during a regular brewing  
cycle.  
B
Before brewing coffee for the first time, clean the coffee outflow unit and  
the pod holders with hot water and some dish soap or in a dishwasher.  
Clean the water reservoir thoroughly in hot water, if necessary with some  
dish soap.  
Now your Philips Senseo coffee machine is ready for use!  
10  
Brewing coffee  
1
Fill the water reservoir with cold water up to the MAX  
indication and put it back into the machine.  
C
Never pour milk, coffee, hot water or carbonated water into the water  
reservoir.  
- ° MIN: minimum amount of water required to brew one 4.0 oz.  
cup of Senseo coffee.  
- °° MIN: minimum amount of water required to brew one 8.0 oz.  
mug or two 4.0 oz. cups of Senseo coffee.  
- HD7810:A full reservoir allows you to make up to five 4.0 oz. cups  
Senseo coffee.  
- HD7811:A full reservoir allows you to make up to ten 4.0 oz. cups  
Senseo coffee.  
2
Press on/off button I.  
C
C
The indicator light blinks while the water is heating up. Heating up takes  
approx. 90 seconds.  
The coffee machine is ready for use when the indicator light is lit  
continuously.  
3
4
Release the lid by moving the lever upwards.  
Open the lid.  
5
First place the appropriate coffee pod holder in the machine.  
Make sure the coffee pod holder is clean and the small hole in the  
center is not clogged (i.e. with loose coffee grounds).  
B
If you want to make one 4.0 oz. cup of Senseo coffee, use the 1-  
C
C
pod holder.  
If you want to make one 8.0 oz. mug or two 4.0 oz. cups of  
Senseo coffee, use the deeper 2-pod holder.  
6
Place the Senseo coffee pod(s) properly in the center of the  
pod holder, with the flat Senseo side up and the rounded side  
facing down.  
B
Use Senseo coffee pods that have been specifically developed for your  
Senseo coffee machine for a pure and smooth taste.  
11  
Place 1 Senseo coffee pod in the 1-pod holder or  
C
C
C
C
Place 2 Senseo coffee pods in the 2-pod holder.  
B
Make sure the coffee in the pod(s) is evenly distributed and press the  
pod(s) lightly into the pod holder.  
Never use torn pods or normal ground coffee, as this could cause the  
B
machine to become blocked.  
7
Close the lid and lock the lever.  
Always check if the lid is properly locked.The lever must be pushed  
down until it snaps home with a click.  
Never start brewing coffee with the lid open!The lid must be properly  
closed.  
8
Place one cup, two cups or one mug under the outflow  
openings.  
If you are using cups, make sure they have a capacity of app. 5.0 oz. If  
you are using a mug, make sure the mug has a capacity of app. 10.0 oz.  
Do not use cups or mugs that are too large, as they will cause the  
coffee to get cold more quickly. If using one cup or one mug, be sure to  
position the cup or mug right under the coffee outflow unit with its  
two openings  
9
Press the button indicating the number of cups of Senseo  
coffee you want to brew.  
C
- ° for one 4.0 oz. cup  
- °° for two 4.0 oz. cups or one 8.0 oz. mug  
The Senseo coffee machine starts brewing.  
- The machine automatically supplies the optimal amount of water.  
- You can interrupt the brewing process at any time by pressing the  
on/off button I. If you switch the machine back on after having  
interrupted the brewing process, the machine will NOT complete  
the interrupted brewing cycle.  
12  
Do not remove the water reservoir during a brewing cycle, as this will  
cause the machine to draw in air.When this happens, the next cup will  
only be partly filled.  
If the mug/cups is/are half full when the machine stops brewing, there  
was not enough water left in the water reservoir to brew two cups or  
one mug. Refill the water reservoir and press button ° to fill up the  
two cups or mug.  
10 Remove and discard the coffee pod(s) after use by lifting the  
coffee pod holder out of the machine and emptying it. Coffee  
pod(s) should not be used more than one time.  
Be careful when doing this, for there may still be some hot  
water/coffee on the coffee pod(s) or steam may escape. If the coffee  
pod sticks to the metal distribution disk inside the lid, let the pod cool  
down first before carefully removing it, making sure not to touch the  
hot metal disk.  
Tips  
By rinsing the coffee pod holders and the coffee outflow unit  
regularly, you will make sure that the coffee always tastes best.  
Senseo coffee will taste best if you stir it before drinking it.  
If you intend to make another cup of Senseo coffee later, just  
leave the coffee machine switched on.The machine will  
automatically switch itself off after app. one hour.  
C
Cleaning  
Never immerse the Senseo coffee machine in water or any other  
liquid.  
Never clean the machine by flushing it with the lid open.  
1
Always turn machine off and unplug the machine before  
cleaning it.  
2
3
Clean the outside of the machine with a moist cloth.  
Remove the coffee outflow unit.  
C
C
You can disassemble the coffee outflow unit for more thorough  
cleaning!  
13  
4
5
Clean the coffee outflow unit, the cup tray and the drip tray in  
hot water, if necessary with some dish soap, or in the  
dishwasher.  
C
C
C
Clean the coffee pod holders in hot water, if necessary with  
some dishwashing soap or in the dishwasher.  
Check if the hole in the center of the pod holders is clogged. If the  
hole is clogged, unclog it by holding the pod holder under a running  
faucet. If necessary, you can use a soft brush, toothpick or a pin to  
unclog the hole.  
6
Clean the water reservoir in hot water, if necessary with some  
dish soap or in the dishwasher.  
The splash guard on the water reservoir can be removed to allow  
thorough cleaning of the inside.  
If you are using a soft brush or mesh covered sponge, be careful not to  
damage the valve in the bottom of the water reservoir.  
B
B
7
Rinse the parts with fresh water after cleaning and put them  
back into the machine.  
8
Clean the metal distribution disk with a moist cloth.  
C
C
Be careful when you do this; make sure that the rubber sealing ring  
does not get stuck under the edge of the metal distribution disk. If it  
does, the coffee machine will start leaking!  
Descaling  
Regular descaling will prolong the life of your Senseo coffee machine  
and will guarantee optimal brewing results for a long time. If the  
machine is used twice a day on average, it must be descaled once  
every 3 months.  
1
Fill the water reservoir up to the MAX indication with white  
vinegar or with a mixture of descaler and water according to  
the instructions on the package of the descaler.Then put the  
water reservoir back into the coffee machine.  
Use a citric acid based descaler.  
14  
2
Press on/off button I.  
C
The machine is ready for use when the indicator light is lit continuously.  
3
Place the 1-pod holder in the coffee machine, preferably with a  
used coffee pod in it. Close the lid and make sure it is properly  
locked.  
We advise you to put a used coffee pod in the pod holder when you  
descale the machine, as it will serve as a 'filter' to prevent the hole in  
the pod holder from getting clogged with scale residues.  
4
Put a bowl with a capacity of at least 1.5 liters/1.6 qt. under the  
coffee outflow unit to collect the vinegar or the mixture of  
descaler and water.  
C
C
5
Press button °° and let the machine operate. Repeat this  
until the water reservoir is empty.  
Never descale the Senseo coffee machine with the lid open. Make  
sure the lid is properly locked.  
6
Repeat steps 1 to 5 with new vinegar or a new mixture of  
descaler and water.  
7
Empty the water reservoir to remove the last vinegar or  
mixture of descaler and water. Repeat step 1 to 5 with fresh  
water only (i.s.o. vinegar or descaler) at least 3 times to fully  
clean the machine. Discard hot water each time.  
Do not refill water reservoir with used hot water.  
8
Discard the used coffee pod and clean the coffee pod holder  
after descaling to prevent the hole in the center from getting  
clogged.  
This coffee machine has no other user-serviceable parts.Any other  
service should be performed by an Authorized Norelco Service  
Location.  
Storage  
If the coffee machine has already been used and therefore has  
been flushed with water, it may only be used and stored in a safe,  
frost-free place to prevent it from becoming damaged.  
Empty water reservoir before storing.  
15  
Assistance  
For assistance call toll free: 1-866-4SENSEO (1-866-473-6736) or visit  
our website: www.senseo.com.  
Authorized Norelco Service Location information is available 24 hours  
a day, 7 days a week.  
Troubleshooting guide  
If you experience a problem with your Philips Senseo coffee machine,  
you may find the solution in the table below. If the table does not  
provide the solution to your problem or if you have a question, see the  
chapter 'Assistance'.  
Problem  
Solution  
The indicator light continues to blink slowly You need to flush the coffee machine. See 'Preparing the machine for  
use'.  
You are using the Senseo coffee machine at an altitude higher than  
2200 m/6800 ft. above sea level.This has caused the water in the  
machine to start boiling before it has reached the required  
temperature, which prevents the machine from functioning properly.  
Switch the machine off and do not use it at altitudes higher than 2200  
m/6800 ft. above sea level.  
The Senseo coffee machine does not  
The coffee machine must be flushed with water before using it for the  
produce coffee when used for the first time first time, so that the boiler will be completely filled with water. Flush  
the coffee machine (see 'Preparing the machine for use') before you  
start brewing coffee.  
The indicator light continues to blink rapidly Make sure that the water reservoir has been properly placed;  
Make sure that there is enough water in the water reservoir (water  
level above the ° MIN level if you want to brew one 4.0 oz. cup and  
above °° if you want to brew one 8.0 oz. mug or two 4.0 oz. cups);  
Make sure that the ambient temperature is not lower than 10cC/50cF.  
If it is lower, the appliance will not function properly.  
Water leaks from the coffee machine  
Make sure that the lid is properly closed (the lever must be properly  
locked);  
Make sure that the water reservoir has not been filled beyond the  
MAX level;  
Make sure that the hole in the center of the coffee pod holder is not  
clogged. If it is, unclog the hole by holding the coffee pod holder under  
a running tap. If necessary, you can use a soft brush, pin or a toothpick  
to unclog the hole;  
Make sure the coffee pod(s) has/have been put properly in the center  
of the coffee pod holder with the flat Senseo side up;  
Make sure the sealing ring has not gotten stuck under the edge of the  
metal distribution disk (see drawing at the beginning of these  
instructions for use);  
Make sure that the drip tray does not overflow. It is unlikely that it will  
overflow, but it is easier to empty when half full than full.  
16  
Problem  
Solution  
It is perfectly normal for some drops of water to spill onto the counter.  
This may happen, for instance, when you place or remove the water  
reservoir. Be careful when removing used coffee pods, for there may  
still be some water on the pods.  
Do not remove the water reservoir when the coffee machine is  
heating up, as this may cause some water to leak out of the machine  
(this water would normally end up in the water reservoir).  
In all other cases, contact the Authorized Norelco Service Location  
nearest you.  
The lid cannot be opened.  
A vacuum may have temporarily formed under the lid.Turn the  
machine off. Pull the lever up as far as it will go and wait 24 hours  
before opening the lid.  
Make sure that the hole in the center of the coffee pod holder is not  
clogged. If it is, unclog the hole by holding the coffee pod holder under  
a running faucet. If necessary, you can use a soft brush or a toothpick to  
unclog the hole.  
If problems continue to occur, contact the Authorized Norelco Service  
Location nearest you.  
The coffee machine produces less coffee than Descale the machine (see 'Descaling').  
before.  
The lid cannot be closed properly.  
Check if a used coffee pod is sticking to the metal distribution disk. If  
this is the case, remove the used pod. Make sure that the sealing ring is  
lying flat.  
The machine has been stored in a room that  
was not frost-free.  
Contact the Authorized Norelco Service Location nearest you.  
The Senseo coffee is not strong enough.  
Make sure you have used the correct number of pods and pressed the  
right button. Use 1 pod in combination with the 1-pod holder and the  
° button. Use 2 pods in combination with the 2-pod holder and the  
°° button;  
Check if the coffee pod(s) has/have been placed properly in the center  
of the pod holder, to prevent water from escaping along the edge of  
the pod(s).When you are using two coffee pods on top of each other,  
make sure that the flat Senseo sides of both pods are facing up and  
rounded sides are facing down. Press the pods lightly into the pod  
holder;  
Make sure you have not used the same pod twice by accident. Do not  
use a pod twice, as it will give the coffee a bad taste. Use a fresh pod  
for every brew;  
The coffee in the pod needs to be evenly distributed;  
If you prefer a more robust flavor, Senseo coffee pods with a stronger  
blend are available.  
The Senseo coffee is too strong  
The coffee is not hot enough  
If you prefer a milder flavor, Senseo coffee pods with a milder blend are  
available.  
Do not use cups that are too large.When using cups, make sure they  
have a capacity of 150 ml/app. 5.0 oz.When using a mug, make sure it  
has a capacity of 280 ml/10.0 oz.  
17  
18  
17  
FULLTWOYEAR WARRANTY  
Philips Electronics North America Corporation warrants each new Philips Product, model  
HD7810 and HD7811 (except cord, coffee pods and accessories) against defects in materials  
or workmanship for a period of two years from the date of purchase, and agrees to repair or  
replace any defective product without charge.  
IMPORTANT: This warranty does not cover damage resulting from accident, misuse or abuse,  
lack of reasonable care, the affixing of any attachment not provided with the product or loss of  
parts or subjecting the product to any but the specified voltage.* Use of unauthorized replace-  
ment parts will void this warranty.  
PHILIPS ELECTRONICS NORTH AMERICA CORPORATION WILL NOT PAY  
FOR WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED REPAIR  
SERVICE AND WILL NOT REIMBURSETHE CONSUMER FOR DAMAGE  
RESULTING FROM WARRANTY SERVICE PERFORMED BY A NON-AUTHO-  
RIZED REPAIR SERVICE.  
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL, INCIDENTAL OR CONSE-  
QUENTIAL DAMAGES.  
In order to obtain warranty service, simply take or ship the product postage prepaid to the  
nearest Authorized Norelco Service Location. It is suggested that for your protection you  
return shipments of product by insured mail, insurance prepaid. Damage occurring during  
shipment is not covered by this warranty.  
NOTE: No other warranty, written or oral, is authorized by Philips Electronics North  
America Corporation.  
This warranty gives you specific legal rights, and you may also have other rights which vary  
from state to state. Some states do not allow the exclusion or limitation of incidental or con-  
sequential damages, so the above exclusion and limitations may not apply to you.  
* Read enclosed instructions carefully.  
Manufactured for: Norelco Consumer Products Company  
A Division of Philips Electronics North America Corporation  
1010 Washington Blvd.  
Stamford, CT 06912-0015  
COFFEE PODS PACKAGED IN BELGIUM.  
This symbol on the product’s nameplate means it is listed by Underwriters’  
Laboratories, Inc.  
®
LISTED  
PHILIPS and Philips Shield are Registered Trademarks of Koninklijke Philips Electronics N.V.  
Senseo is a Trademark of Koninklijke Philips Electronics N.V. when used for coffee makers.  
Senseo is aTrademark of Sara Lee/DE N.V. when used for coffee pods.  
© 2004 Philips Electronics North America Corporation.All Rights Reserved.  
4222 002 29982  

Technicolor Thomson LAD960U User Manual
Sylvania IMODE SIP3019 User Manual
Sunbeam 6385 User Manual
Sony CD Player CDX L380X User Manual
SIIG 04 0265F User Manual
Seagate U10TM ST310212A User Manual
Samsung GH68 05273A User Manual
Research In Motion Blackberry Cell Phone 9800 User Manual
Philips FM01SW80 User Manual
Philips AZ1015 User Manual