iHome IP23 User Manual

Model iP23  
Dual Alarm Clock  
for iPhone and iPod ®  
FCC Information  
This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
This equipment complies with the limits for a Class B digital device as specified in Part 15 of FCC Rules. These limits  
provide reasonable protection against radio and TV interference in a residential area.  
However, your equipment might cause TV or radio interference even when it is operating properly. To eliminate interference  
you can try one or more of the following corrective measures:  
• Reorient or relocate the receiving antenna.  
• Increase the distance between the equipment and the radio or TV.  
• Use outlets on different electrical circuits for the equipment and the radio or TV.  
• Consult your dealer or an experienced radio/television technician if the problem still exists.  
Modifying or tampering with your systems internal components can cause a malfunction and might invalidate the systems  
warranty and void your FCC authorization to operate it.  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
Battery Warning  
For models that require more than one battery  
• Do not mix with used or other battery types/brands  
• Replace all batteries at the same time  
• Do not open batteries  
• Do not dispose of in fire  
• Do not heat above 75ºC (167ºF)  
• Do not expose contents to water  
• Do not charge or recharge  
• Do not install backwards  
Controls and Indicators  
Dock  
Top Panel  
Lower Volume Button  
Sleep Button  
Raise Volume Button  
Forward Button  
Alarm 2 Button  
Alarm Reset / Power Button  
Alarm 1 Button  
Reverse Button  
Play/Pause Button  
Snooze/Dimmer Button  
Rear Panel  
Aux Line-in Jack  
Time Zone Button  
DST Switch  
AC Adaptor Jack  
Time Sync/Set Button  
1
iP23 Quick Start  
1: power  
3: iPhone/iPod  
2: inserts  
RESET  
R E S E T  
ES
Select the dock insert for your  
iPhone/iPod model from the table  
below and place insert in dock.  
To remove insert, place  
thumbnail in slot and gently pull  
upwards.  
Insert playing iPhone/iPod into the dock  
(must not be in a “skin” or case). Your  
audio will play through the unit. Press  
volume buttons to adjust volume.  
iPhone/iPod will charge while docked.  
Attach AC adaptor cable to jack  
on back of the unit and plug the  
other end into a wall socket to  
play and charge iPhone/iPod.  
iPhone 4  
iPhone 3G  
insert 15  
nano 5G  
insert 18  
iPod touch 2G  
insert 16  
nano 6G/touch 4G  
insert 19  
insert 20  
Use this insert  
iPhone 4  
nano 6G  
iPhone 3G/3GS  
iPod touch 2G/3G  
nano 5G  
For this iPhone / iPod  
iPod touch 4G  
Note: An insert provides the best stability and safety for your iPhone/iPod, but you can safely dock your iPhone  
or iPod without an insert, provided you always do so with care. If you prefer to use an insert and don’t have one  
• Make sure your iPhone or iPod is properly docked  
4:time sync  
• Press the Time Sync/Set button on the back of the unit  
• “SYNC” will appear on the display, followed by “DONE”  
• If “FAIL” appears, try again with a different iPhone or iPod, or see  
Setting Time Manually (page 4).  
2
Display  
Sleep indicator  
Buzzer indicator  
Battery Low Indicator  
Alarm 1, Alarm 2 Indicators  
PM Indicator  
Time Display  
iPod Indicator  
Installing/Replacing Clock Backup Batteries  
The unit uses 2 AA batteries (installed) for backup to provide continuous alarm operation and clock settings in the event of a  
power failure. If the backup batteries have been installed and a power failure occurs or the AC adaptor is accidentally  
disconnected, the display backlight will not remain lit, but current time and alarm time settings will be temporarily maintained.  
Otherwise, you must reset the time and alarm settings.  
Note: You should replace backup batteries when the Battery Low Indicator flashes on the display.  
1. Please make sure the AC adaptor is connected. Otherwise all settings may be lost during battery replacement.  
2. Open backup battery compartment door located on the bottom of the unit.  
3. Insert 2 “AA” batteries, checking the + and – ends of the batteries match the diagram  
to the right. We recommend alkaline batteries for longer life time. Do not mix alkaline,  
standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.  
4. Close the compartment cover.  
Note: Make sure you dispose of batteries properly (see your local regulations).  
3
Operating the Unit  
This unit has a PRESET Clock: the time is already preset to Eastern time at the factory. Simply match the time zone setting to  
where you live.  
1. Depending on your location and whether or not Daylight Saving Time (DST) is in effect, set the DST Switch located  
on the back of the unit to +1 to add an hour or to -1 to subtract an hour to/from the currently displayed time.  
2. Press and hold the Time Zone Button located on the back of the unit until the current time zone flashes. The unit will  
beep. Press the  
or  
Button to select your time zone.  
3. Press the Time Zone Button again (or no button within 10 seconds) to exit the setting mode. 2 beeps will confirm Time  
Zone setting is complete.  
4. If the displayed time is not correct, see instructions below to set the clock.  
Setting the Clock Time Using Time Sync  
The Time Sync feature allows you to sync the time setting on the unit to the time on your iPhone or recent model  
iPod (iPod touch, iPod nano and iPod Classic; older iPod models such as iPod mini do not support this feature).  
1. Press the Time Sync/Set Button located at the back of the unit. “Sync” flashes on the display and a beep sounds.  
2. Once sync is completed, “DONE” appears on the display followed by 2 beeps indicating time sync is complete.  
The updated time will appear on the display.  
3. If sync was not successful, “FAIL” will appear on the display and a long beep will sound. If this happens, please try again,  
with a different iPhone or iPod if needed. If sync still fails, please see Setting Time Manually below to set the clock.  
NOTE: iPhone time is automatically updated to the correct time via cell phone towers. The time on your iPod is accurate only  
to the time on the computer the last time the iPod was synced to it. It’s possible to have up to 59 seconds difference between  
the unit and synced iPhone/iPod.  
Setting Time and Calendar Manually  
1. Press and hold the Time Sync/Set Button located on the back of the unit until the current time flashes on the display.  
Press the  
2. Remember to set the correct AM or PM time. The PM Indicator is located to the left of the time display; there is no AM  
indicator. Press and release the or Button during time setting to toggle between standard 12 hour time display and  
or  
Button to adjust to the correct time (hold the button to advance or reverse rapidly).  
24 hour time display. The PM indicator is disabled when time display is set to 24 hours.  
3. Press the Time Sync/Set Button. The year will be displayed and a beep will sound. Press the  
current year is displayed.  
or  
Button until the  
or Button  
4. Press the Time Sync/Set Button again. The month and date will appear (ex. 3:13 = March 13). Press the  
until the current month/date is displayed. Holding the button for a few seconds will advance or reverse rapidly.  
5. Press the Time Sync/Set Button again (or no button within 10 seconds) to exit the time/calendar setting mode. You will  
hear two beeps confirming Time and Calendar setting are completed.  
Using the Alarms  
Setting the Alarms  
1. By default, the unit selects iPhone/iPod as your wake source. If no iPhone/iPod is docked or detected, the unit will  
automatically default to buzzer alarm.  
Note: The alarm sounds for 1 hour. Make sure you have an hour of audio on your iPhone/iPod.  
2. Press and hold the  
Remember to set the correct AM or PM time.  
3. Press the Button (or no button press within 10 seconds). Two beeps will confirm alarm one is set and exit alarm  
setting mode. The alarm is then armed, indicated by the alarm icon on the display.  
Button until the display flashes. The unit will beep.Press the  
or  
Button to set the alarm time.  
4
4. To set Alarm 2 just follow steps 2 - 3 using the  
Button.  
Operating the Unit  
Reviewing, Arming and Disarming Alarm (Turn Alarm Function On and Off)  
1. Once an alarm is set, press the associated alarm button to view the currently set alarm time and to toggle the alarm on  
(icon) or off (no icon).  
2. To arm/disarm the alarm, just press the associated alarm button to toggle it on or off. If the alarm is armed, the related  
alarm icon will appear on the right side of the display.  
Resetting the Alarm to Come on the Next Day  
1. When the alarm is sounding, press the  
Button to stop the alarm and reset it to come on the following day. You can  
also press the alarm button for the sounding alarm (alarm 1 or alarm 2) to reset it.  
Snooze Operation  
1. By default, snooze lasts for 9 minutes. To adjust the snooze time, press and hold the Snooze/Dimmer Button until the  
display flashes. Press the  
or  
Button to set the snooze timer from 1 to 29 minutes.  
2. Press the Snooze/Dimmer Button after the alarm sounds. The alarm will be silenced and come on again after the set  
snooze time. Snooze can be pressed several times during the 1 hour alarm cycle.  
Sure Alarm  
The unit has a sure alarm feature. If backup batteries are installed, the buzzer alarm will still sound in the event of power failure.  
Charging your iPhone/iPod  
Gently dock your iPhone/iPod using the insert for your iPhone/iPod (see Qucik Start guide). Using an insert provides the best  
stability and protection, but you can safely dock your iPhone/iPod without an insert.  
1. While your iPhone/iPod is docked in the unit and the unit is connected to AC power, it recharges (until fully charged). Back  
up batteries will NOT charge iPhone/iPod. Note that non-docking iPhone/iPod models will NOT charge.  
Listening to your iPhone/iPod  
1. Dock your already playing iPhone/iPod. The unit will automatically turn on and after a few moments you will hear the audio  
playing from your iPhone/iPod, starting softly and gradually increasing to the set volume.  
Note: If the volume on the playing track is too low, the unit may not detect that your iPhone/iPod is in play mode. If this  
happens, press the  
Button on the main unit to play it.  
2. When the iPhone/iPod is docked and in standby mode, press the  
the display, indicating iPhone/iPod play mode.  
Button on the unit to play it. The  
will appear on  
3. Press the  
4. Press the Volume  
5. Press the or  
speed forward or reverse music search of the current track.  
6. To turn off the unit, press the Button. The iPhone/iPod will continue charging while in the dock.  
Button to pause play; press again to resume it.  
and Volume Button to adjust the system volume.  
Button on the unit to go to the next or previous track. Press and hold while a track is playing for high  
5
Operating the Unit  
Using the Aux line-in Jack  
If you have an audio device with standard 3.5 mm headphone jack, you can play it through the unit via the Line-in Jack located  
on the back of the unit.  
1. Plug one end of an audio patch cord (available at www.ihomeaudio.com) into the headphone or line-out jack on your  
device and the other end of the patch cord into the Aux line-in Jack.  
2. Press the  
Button to turn the unit on.  
3. Turn on and play your device.  
4. Press the Volume  
too.  
and Volume  
Button to adjust the system volume. You may need to adjust your device volume,  
5. To turn off the unit, press the  
Button. Please remember to turn off your device, too.  
NOTE: Do not listen to aux line-in audio source while a docked iPhone/iPod is playing or you will hear both audio sources.  
Sleep Operation  
Sleep mode lets you sleep to your iPhone/iPod until the unit shuts off at a selected time.  
1. Press the Sleep Button to enter sleep mode. The Sleep Icon will appear on the display to indicate it is in sleep mode.  
2. Press the Sleep Button as needed to adjust the sleep timer from 90, 60, 30 or 15 minutes (or turn sleep OFF).  
3. When the display changes back to show the real time, press the Sleep Button once to show the sleep time remaining.  
Pressing it again to change sleep time to the next lowest increment.  
4. To stop listening at any time, press the  
Button to turn unit off.  
Dimmer Operation  
During normal operation, press the Snooze/Dimmer Button to control the brightness of the LCD display.  
6
A Consumer Guide to Product Safety  
When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However,  
improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully  
before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in  
these instructions and on the unit.  
1. Water and Moisture – The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink,  
laundry tub, swimming pool or in a wet basement.  
2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For  
example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also, it  
should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of air through  
the ventilation openings.  
3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances  
(including amplifiers) that produce heat.  
4. Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions  
or as marked on the appliance.  
5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to be walked on or pinched  
by items placed upon or against them. It is always best to have a clear area from where the cable exits the unit to where  
it is plugged into an AC socket.  
6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance section of this manual for cleaning  
instructions.  
7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into any openings  
or vents located on the product.  
8. Attachments – Do not use attachments not recommended by the product manufacturer.  
9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or cable  
system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent damage  
to the product due to lightning and power-line surges.  
10. Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result in  
a risk of fire or electric shock.  
11. Damage Requiring Service – The unit should be serviced by qualified service personnel when:  
A. the power supply cable or plug has been damaged.  
B. objects have fallen into or liquid has been spilled into the enclosure.  
C. the unit has been exposed to rain.  
D. the unit has been dropped or the enclosure damaged.  
E. the unit exhibits a marked change in performance or does not operate normally.  
12. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer, the power  
cable should be unplugged from the unit to prevent damage or corrosion.  
13. Servicing – The user should not attempt to service the unit beyond those methods described in the users operating  
instructions. Service methods not covered in the operating instructions should be referred to qualified service personnel.  
7
Trouble Shooting  
Symptom  
Possible Problem  
Solution  
Unit doesn’t respond AC adaptor isn’t plugged to a wall outlet or  
Plug the AC adaptor into a wall outlet and plug the connector into  
the power supply jack on the unit  
(no power)  
the connector is not plugged into the power  
supply jack on the back of the unit  
Wall outlet is not functioning  
Plug another device into the same outlet to confirm the outlet is working  
Make sure the dock insert is the proper fit for your iPhone/iPod  
iPhone/iPod cannot Using wrong insert  
dock properly  
Possible obstruction in dock area or on  
Remove your iPhone/iPod from the connector and check for  
any obstruction on the connectors in the dock. Try removing  
case or skin from your iPhone/iPod. Then reseat it in the dock.  
iPhone/iPod (skin or case is in the way)  
Playing iPhone/iPod  
but there is no  
sound  
Remove your iPhone/iPod from the connector and check for  
any obstruction on the connectors in the dock and on your  
iPhone/iPod. Then reseat it in the dock.  
iPhone/iPod is not docked properly  
Press play button on your iPhone/Pod to play it manually.  
Your iPhone/iPod is not playing  
iPhone/iPod is locked up  
Please make sure your iPhone/iPod is working properly before  
docking it to the unit. Please refer to your manual for details.  
Using 1st or 2nd generation iPod, iPod shuffle or  
other device  
Please connect them with Line-in.  
iPhone/iPod didn’t  
charge up  
Remove your iPhone/iPod from the connector and check for  
any obstruction on the connectors in the dock and on your  
iPhone/iPod. Then reseat it in the dock.  
iPhone/iPod is not docked properly  
iPhone/iPod is locked up/frozen  
iPhone/iPod battery has problem  
Volume level is set too high  
Sound source is distorted  
Please make sure your iPhone/iPod is working properly before  
docking it to the unit. Please refer to your manual for details.  
Sound is distorted  
Decrease the unit volume  
If original sound source file is poor quality, distortion and noise  
are easily noticed with high-power speakers.  
Try a file from a trusted audio source such as iTunes  
If you are using an iPod shuffle or external sound source like  
older generation iPod, try reducing the output volume on the  
device itself. Also, try turning bass boost OFF under iPod  
settings.  
8
Limited 1 Year Warranty Information  
iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from defects  
in workmanship and materials, under normal use and conditions, for a period of 1 year from the date of original purchase.  
Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased. Should this  
fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period, SDI Technologies will  
repair or, at its discretion, replace this product without charge (except for a $10.00 charge for handling, packing, return UPS/postage, and  
insurance). This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service Center listed  
below. The product must include proof of purchase, including date of purchase. The fee for service without proof of purchase is $20.00.  
Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or defective batteries are  
the most common cause of problems encountered.  
If service is still required:  
1. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box.  
2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of purchase, if within the warranty period.  
3. Enclose a check or money order payable to the order of SDI Technologies, for the sum of $10.00 ($20.00 without proof of purchase).  
4. Send the unit prepaid and insured, to the Factory Service Center listed below.  
Consumer Repair Department  
SDI Technologies Inc.  
1330 Goodyear Drive  
El Paso, TX 79936-6420  
Disclaimer of Warranty  
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i) products which have  
been damaged by negligence or willful actions, misuse or accident, or which have been modified or repaired by unauthorized persons; (ii)  
cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players, CD’s or tape cassettes (if applicable); (iv)  
the cost of shipping this product to the Factory Service Center and its return to the owner.  
This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original purchaser.  
In no event will SDI Technologies or any of its affiliates, contractors, resellers, their officers, directors, shareholders, members or agents be liable  
to you or any third party for any consequential or incidental damages, any lost profits, actual, exemplary or punitive damages. (Some states do  
not allow limitations on implied warranties or exclusion of consequential damages, so these restrictions may not apply to you.) This warranty  
gives you specific legal rights, and you may also have other rights which vary from state to state.  
Your acknowledgement and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually binding  
to you upon your transfer of currency (money order, cashier's check, or credit card) for purchase of your SDI Technologies product.  
© 2011 SDI Technologies, Inc. All rights reserved  
or call 1-800-288-2792 Toll Free  
iP23-012611-English  
Printed in China  
9

Nespresso C100 User Manual
Motorola i550plus User Manual
Manhattan Computer Products 451109 User Manual
LG Electronics G7050 User Manual
Lenoxx Electronics CD 110 User Manual
Kenwood DPF J9010 User Manual
Dynex DX CDRW52 User Manual
Black Box LTD5 User Manual
Ariston MCA15NAP User Manual
Antec Quiet Computing 3U22EPS600 User Manual