’
OWNER S
MANUAL
Quick Guide to Functions
Answer a call - Press SEND or any key
but END or PWR.
Clear a digit from display - Press CLR.
Clear the entire display - Press and hold CLR.
Emergency 9 call - Press and hold 9 for 2 seconds.
(Note: Emergency 9 dialing must be set to on! You can also dial
911, then press SEND)
End a call - Press END.
Find a stored name - With clear display, press ABC then !.
Find a stored number - With clear display, press !.
Keyguard activate - Press and hold END, or press MENU *.
Keyguard deactivate - Press MENU *.
Last 15 dialed numbers - With clear display, press SEND then
!. Press SEND again to dial displayed number.
Last number redial - With clear display, press SEND SEND.
Make a call - Enter area code and phone number then press
SEND.
One-touch dial - Press and hold 1-8 for 2 seconds.
(Note: One-touch dialing must be set to on!)
PINCALL activate - Press * # PINCALL #, key in PIN code, then
press OK.
PINCALL deactivate - Press * # PINCALL #, then OK.
Speed dial - Press a location number (1-75) then press SEND.
Store a number (quick) - Key in area code and phone number
then press OK OK.
Switch on/off - Press and hold PWR for one second.
Volume - adjust - During a call, press ! or ".
Quick Guide to Menu
Backstep one level - Press CLR.
Enter menu - Press MENU.
Exit menu - Press END.
Scroll through menu - Press MENU then ! or ".
Select a submenu or option - Press OK.
Shortcuts - Press MENU then the menu number.
MENU SUMMARY
4 Security Settings
1
2
3
Change Lock Code
Change Security Code
Restore Factory Settings
1 Phone Book
1
2
3
4
5
Find Name
Save Name & Number
Edit Name or Number
Erase from Phone Book
Phone book Status
5 Call Settings
1
2
Calling Options
Calling Card*
6 Lock Phone
Prevents outgoing calls and access
to all phone functions.
2 Call Log
1
2
3
4
5
Dialed Calls
Received Calls
Missed Calls
Erase all Recent Calls
Call Timers
7 Messages**
1
2
3
Read Messages
Erase Messages
Message Alert Tone
8 Debit (TRACFONE only)
3 Phone Settings
1
2
Timetank Info
Checksum
1
2
3
4
5
6
7
8
9
Ringing Options
Ringing Volume
Ringing Tone
Keypad Tones
Lights
1-Touch Dialing
Emergency 9 Dialing
Language
9 Prepaid (if available)
1
2
3
4
Check Balance
Add Money to Account
Prepaid Card
Save Access Numbers
*
This option is not available if
Prepaid (Menu 9) is activated.
** Messages menu is available on
Nokia 252N only. Messages feature
depends on network subscription.
Phone Number
10 Automatic Answer
11 Automatic Redial
Keys
Retractable antenna. Extend fully
during calls.
Switches the
phone on and
off when
pressed and
held.
Confirms and
selects
choices on
display.
Scrolls through
menu functions.
Also adjusts
earpiece vol-
ume during a
call.
Enters the
menu.
Switches
Deletes
between alpha
and numeric
modes.
characters or
clears display.
Backspaces
one menu
level.
Ends a call.
Activates Key-
guard when
pressed and
held. Exits the
menu.
Dials a phone
number and
answers
a call.
0-9, ∗, #:
Used to enter
numbers and
characters.
Shows Life
Timer when
pressed and
held.
Contents
1. For Your Safety. . . . . . . . . . . . . . . . .1
2. Display Indicators . . . . . . . . . . . . . . 3
3. Battery Information. . . . . . . . . . . . . 5
Installing the Battery . . . . . . . . . . . . . . . . 5
Removing the Battery . . . . . . . . . . . . . . 5
Charging the Battery . . . . . . . . . . . . . . . 6
Discharging the Battery . . . . . . . . . . . . . 8
Important Battery Information . . . . . . . 10
4. The Basics . . . . . . . . . . . . . . . . . . .12
Switching On or Off . . . . . . . . . . . . . . . 12
Wake-up Message . . . . . . . . . . . . . . . . 12
Selecting a Network . . . . . . . . . . . . . . . 13
Making a Call . . . . . . . . . . . . . . . . . . . . 13
Ending a Call . . . . . . . . . . . . . . . . . . . . . 14
Answering a Call . . . . . . . . . . . . . . . . . . 14
Adjusting the Earpiece Volume . . . . . . 15
Last Number Redial . . . . . . . . . . . . . . . 15
Speed Dialing . . . . . . . . . . . . . . . . . . . . 16
1-Touch Dialing . . . . . . . . . . . . . . . . . . . 16
Emergency 9 Dialing . . . . . . . . . . . . . . 16
Keyguard . . . . . . . . . . . . . . . . . . . . . . . 17
Calling Card Calls . . . . . . . . . . . . . . . . . 18
PIN Calls . . . . . . . . . . . . . . . . . . . . . . . . 19
Voice and Text Messages . . . . . . . . . . 20
What is Debit Mode? . . . . . . . . . . . . . . 21
5. The Phone Book . . . . . . . . . . . . . . 22
Viewing and Entering Names . . . . . . . . 22
Saving Numbers and Names . . . . . . . . 24
Finding Numbers and Names . . . . . . . 26
Using the Notepad Memory. . . . . . . . . 26
i
Moving a Name and Number . . . . . . . 27
Erasing a Name and Number . . . . . . . 27
Editing a Name and Number . . . . . . . . 27
6. The Menu. . . . . . . . . . . . . . . . . . . . 28
“MENU then OK” Method . . . . . . . . . . 28
Shortcut Method . . . . . . . . . . . . . . . . . 29
Using the Menu During a Call . . . . . . . 29
List of Menu Functions. . . . . . . . . . . . . 30
Phone Book (Menu 1) . . . . . . . . . . . . . .31
Call Log (Menu 2) . . . . . . . . . . . . . . . . . 33
Phone Settings (Menu 3) . . . . . . . . . . . 36
Security Settings (Menu 4) . . . . . . . . . 43
Call Settings (Menu 5) . . . . . . . . . . . . . 45
Lock Phone (Menu 6) . . . . . . . . . . . . . 52
Messages (Menu 7) . . . . . . . . . . . . . . . 52
Debit (Menu 8) . . . . . . . . . . . . . . . . . . . 55
Prepaid (Menu 9) . . . . . . . . . . . . . . . . . 59
In-Call Menu . . . . . . . . . . . . . . . . . . . . . 63
Reminder Message . . . . . . . . . . . . . . . 64
7. Data and Touch Tones . . . . . . . . . 65
Data Mode . . . . . . . . . . . . . . . . . . . . . . 65
Sending Touch Tones . . . . . . . . . . . . . 66
Using the Flash Function . . . . . . . . . . . 68
8. Network Services . . . . . . . . . . . . . 69
Availability of Network Services. . . . . . 69
Calling Line Identification . . . . . . . . . . . 69
Call Waiting . . . . . . . . . . . . . . . . . . . . . . 70
Message Waiting (Voicemail) . . . . . . . .71
Digital Message Service
(Nokia 252N only) . . . . . . . . . . . . . . . . 73
ii
9. Accessories . . . . . . . . . . . . . . . . . 75
10. Reference Information . . . . . . . . . .81
Important Safety Information . . . . . . . . 81
Care and Maintenance . . . . . . . . . . . . . 87
11. Troubleshooting . . . . . . . . . . . . . . 88
12. Technical Information. . . . . . . . . . 89
13. NOKIA One-Year Limited Warranty. . 90
14. Index . . . . . . . . . . . . . . . . . . . . . . . 94
iii
1. For Your Safety
Read these simple guidelines before using your
phone. Failure to comply with these guidelines
may be dangerous or illegal.
For more detailed safety information, see
Road Safety Comes First
Don’t use a hand-held phone while driving; park
the vehicle first.
Switch Off In Hospitals
Switch off your phone when near medical
equipment. Follow any regulations or rules in
force.
Switch Off On Aircraft
Mobile phones can cause interference.
Using them on aircraft is illegal.
Switch Off When Refueling
Do not use the phone at a refueling point.
Do not use near fuels or chemicals.
Switch Off Near Blasting
Do not use the phone where blasting is in
progress. Observe restrictions, and follow any
regulations or rules in force.
Interference
All mobile phones may get interference which
could affect performance.
Use Sensibly
Use only in the normal position (to ear).
Avoid unnecessary contact with the antenna
when phone is on.
1
Qualified Service
Only qualified service personnel may install or
repair cellular phone equipment. Use only
approved accessories and batteries.
FCC/Industry Canada Notice
A cellular phone may cause TV or radio interference
(e.g. when using a phone in close proximity to electronic re-
ceiving equipment). The FCC/Industry Canada can require
you to stop using your cellular phone if such interference
cannot be eliminated. If you require assistance, please
contact your local service facility.
This device complies with part 15 of the FCC rules.
Operation is subject to the condition that this device does
not cause harmful interference.
Using this Guide
The cellular phone described in this guide is approved for
use in AMPS and/or NAMPS networks.
A number of features included in this guide are called
Network Services. They are special services provided by
cellular service providers. Before you can take advantage
of any of these Network Services, you must subscribe to
the service(s) from your home service provider and obtain
instructions for their use.
2
2. Display Indicators
Shows which type of system the phone will
use when it is roaming (see “Carrier Selection
(Menu 5 1 1)” on page 45.) Blank if Home-only
system is selected, or the phone is using a
“preferred” network.
The phone is using the Home system.
Flashes if the phone is using a Home type system
(not the Home system) or when the phone is using
a “preferred” network (see “Carrier Selection
Blank if the phone is using a non-preferred network.
A call is in progress.
The phone is in alpha mode; you can enter letters
and see names.
Indicates that you have received a voice mail
message.
Indicates that you have received a short text mes-
sage. Blinks when Messages list (memory) is full.
Indicates menu or memory location number; may
indicate number of unheard voice messages.
and bar indicate the cellular signal strength of the
location where you are using your phone.
and bar indicate the battery charge level. When the
battery is fully charged, the whole bar is displayed.
3
Signal Strength Indication
A cellular phone sends and receives radio signals. As with
all radio equipment, the quality of radio reception depends
on the strength of the radio signal in the area where you
are operating your phone.
The strength of the cellular signal is shown by
the vertical bar on the left-hand side of the dis-
play. The higher the bar, the stronger the signal
at your present location.
When NO SERVI CE is displayed, the phone is
either outside of the cellular service area or re-
stricted from entering service, and calls cannot
be made or received.
If the signal is poor and you are using the phone in a
building, you may get better reception near a window.
4
3. Battery Information
Your phone is powered by a rechargeable battery. Use
only batteries approved by the phone manufacturer and
recharge your battery only with the chargers approved by
the manufacturer. See “Important Battery Information” on
See your cellular service provider or dealer for the battery
options available for your phone.
Installing the Battery
➋
➋
Removing the Battery
➋
➋
➋
Note: Switch off the
phone’s power before
removing the battery!
5
Charging the Battery
Plug the charger into a wall outlet and connect the charger
to the bottom of your phone.
When charging starts, the battery
segments scroll and the phone
beeps once.
You can use the phone during charg-
ing, but charging will be reduced for
the duration of the call.
Note: In a call, charging will stop completely if you are
using the Standard Travel Charger (ACP-7U).
After the segments of the battery indicator stop
scrolling and all segments are displayed, the
battery is fully charged. Disconnect the charger
from the power outlet and phone.
If the battery is too hot or cold, the charging may
be interrupted until the battery reaches its normal
operating temperature.
Note: With a new, completely discharged battery, the
phone may take up to 45 minutes to show that charging
is in progress.
6
Charging Times
The battery charging times shown in the following table
are approximate.
Standard
Travel
Charger
ACP-7U
Rapid
Travel
Charger
ACP-9U
Rapid
Cig. Lighter
Charger
LCH-9
Battery
BMH-3
Extended
NiMH
1150 mAh
1 hour,
30 min.
1 hour,
30 min.
5 hours
7 hours
BMH-8
UltraExtended
NiMH
1580 mAh
2 hours,
30 min.
2 hours,
30 min.
BML-8
UltraExtended
Vibra NiMH
1580 mAh
7
Talk and Standby Times
Battery operation times depend greatly on how you use the
batteries, as well as on the coverage of the network and
network parameters set by the cellular service provider.
Standby
Time
Battery
Talk Time
BMH-3
Extended NiMH
1150 mAh
up to
2 hours
up to
39 hours
BMH-8
Ultra Extended NiMH
1580 mAh
up to
up to
3 hours
58 hours
BML-8
Ultra Extended Vibra NiMH
1580 mAh
Discharging the Battery
A battery lasts longer and performs better if you fully
discharge it from time to time. To discharge the battery,
leave your phone switched on until the battery is drained
and the phone turns itself off. Then wait for 30 minutes
before connecting to a charging source. (See “Deep
Note: Do not discharge the battery by any other means.
8
Battery Low Warning
You get this message and a warning
tone when the battery charge is low
and only a few minutes of talk time
remain.
The repetition rate of the battery-low
warnings depends on the remaining battery capacity and
the battery condition. The warnings are more frequent
when you’re in a call.
Note: If you’ve selected the Vibra Only or Silent Ringing
Option, you won’t hear any warning tones. See “Ringing
When the battery charge is too low for the phone to work,
the phone displays RECHARGE BATTERY, then beeps,
then shuts itself off.
Charge the battery as described earlier in this section.
Deep Discharge
If you regularly just ‘top up’ the charge in your battery
without ever allowing it to fully discharge first, its life will be
shortened. In order to get the maximum life from your
battery you should allow it to discharge completely about
once a month.
To discharge the battery completely:
1
Leave the phone switched on until RECHARGE
BATTERY appears, then let the phone switch off
automatically.
2
Leave the phone alone for about 30 minutes (and do
not connect a charger within this time) after it
switches itself off.
9
During this 30 minutes, the phone is in ‘Deep
Discharge’ mode. The way to ‘wake up’ the phone is
to connect it to a charger.
3
Fully charge the battery after Deep Discharge.
The phone may remind you to discharge the battery, by
presenting a series of battery-advice messages. Press !
or OK to page through the information, or press CLR to
clear the messages.
Important Battery Information
•
Note that a new battery’s full performance is achieved
only after two or three complete charge and discharge
cycles!
•
The battery can be charged and discharged hundreds
of times but it will eventually wear out. When the
operating time (talk time and standby time) is notice-
ably shorter than normal, it is time to buy a new battery.
•
•
Use only batteries approved by the phone manufac-
turer and recharge your battery only with the chargers
approved by the manufacturer.
When a charger is not in use, disconnect it from the
power source. Do not leave the battery connected to
a charger for longer than a week, since overcharging
may shorten its life. If left unused a fully charged
battery will discharge itself over time.
•
(NiMH batteries only) For good operation times,
discharge the battery from time to time by leaving
your phone switched on until it turns itself off (or by
using the battery discharge facility of any approved
accessory available for your phone). Do not attempt
to discharge the battery by any other means.
10
•
Temperature extremes will affect the ability of your
battery to charge: allow it to cool down or warm up
first.
•
•
Use the battery only for its intended purpose.
Never use any charger or battery which is damaged
or worn out.
•
•
Do not short circuit the battery. Accidental short cir-
cuiting can occur when a metallic object (coin, clip, or
pen) causes direct connection of the + and - terminals
of the battery (metal strips on the back of the battery),
for example when you carry a spare battery in your
pocket or purse. Short circuiting the terminals may
damage the battery or the connecting object.
Leaving the battery in hot or cold places, such as in a
closed car in summer or winter conditions, will reduce
the capacity and lifetime of the battery. Always try to
keep the battery between 59º F and 77º F (15º C and
25º C). A phone with a hot or cold battery may
temporarily not work, even when the battery is fully
charged. NiMH batteries’ performance is particularly
limited in temperatures below 14º F (-10º C). Li-Ion
batteries’ performance is particularly limited in
temperatures below 32º F (0º C).
•
•
Do not dispose of batteries in a fire!
Dispose of used batteries in accordance with any
local regulations.
11
4. The Basics
Switching On or Off
•
Press and hold the PWR key for one second.
NORMAL POSITION: Hold the phone as you would any
other telephone with the antenna pointed up and over
your shoulder.
TIPS ON EFFICIENT OPERATION: Extend your antenna
fully when in calls. As with any other radio transmitting
device, avoid unnecessary contact with the antenna when
the phone is switched on. Contact with the antenna
affects call quality and may cause the phone to operate at
a higher power level than otherwise needed.
WARNING! Do not switch the phone on when cellular phone
use is prohibited or when it may cause interference or danger.
Wake-up Message
When you switch your phone on, the phone displays a
wake-up message consisting of the phone number cur-
rently selected for your phone, or the name of the dealer if
this has been programmed. (If programmed, the name
takes precedence over the phone number.)
To change the wake-up message:
1
Press ABC, then enter the message. Press OK.
2
At the prompt SAVE I N LOCATI ON?, press ∗. Press
OK. (The wake-up message is stored in location ‘∗’.)
Note: The Wake-up Message is different from the Reminder
Message you can store in your phone. See “Reminder
12
Note: The wake-up message is specific to your currently
selected phone number.
Selecting a Network
Your phone operates on specific networks and sometimes
it must choose which system to use. This can happen, for
example, if you are roaming (i.e. you leave the area where
you have signed up for service).
If you want your phone to work only in certain types of
networks (for example, to take advantage of certain billing
agreements between systems), you can specify this using
Making a Call
1
Extend the phone’s antenna fully.
2
Enter the area code and phone number, then press
SEND. If you make a mistake, press CLR to erase
digits one by one. Press and hold CLR to clear the
whole display.
A phone symbol appears on the
display. The call is connected when
the phone number disappears from
the display and CALL appears.
For international calls, you can enter a
‘+’ at the beginning of a number by pressing ∗∗. Then enter
the number, then press SEND. The ‘+’ expands to the
international dialing code prefix.
NO SERVI CE appears and the phone beeps if you try to
make a call when your phone is outside the cellular service
area.
13
CALL NOT ALLOWED appears if you try to make a call
that is restricted (see “Allowed Calls (Menu 5 1 2)” on
page 48), or if the phone is locked.
If you receive a call when you’re trying to make a call, the
incoming call comes through and the outgoing call is
cancelled.
Ending a Call
•
Press END.
Note: If you press and hold END, you’ll activate Keyguard
Answering a Call
•
•
Press SEND or any key except END or the PWR key.
To answer a waiting call (normally indicated by a beep),
press SEND. (Note that Call Waiting is a network fea-
ture. You need to subscribe to it through your service
provider.)
You can press END to stop the ringing sound without
answering the call.
Make sure the antenna is fully extended during the call.
Note: If Keyguard is active, a call can only be answered
with SEND.
When there is an incoming call, the
phone rings and CALL flashes on the
display.
If you have set Ringing Options to
SI LENT, the keypad and display lights
flash, CALL flashes on the display and the phone makes a
14
You can answer a call any time, even while using Keyguard,
memory or menu functions.
If you don’t answer a call, the message 1 MI SSED CALL
or ‘ n’ MI SSED CALLS appears on the display and
remains until you press any key (except the PWR key) to
clear the display, or you can press OK or ! to view the
Missed Calls List. The phone automatically stores the
caller’s number (if available) in the Missed Calls list
scroll the list, you first see a message telling you the
number of new numbers (e.g., ‘n’ NEW NUMBER(S), or NO
NEW NUMBERS; wait for most recent number to appear or
press !. Press ! to scroll the list.
Calling Line Identification
If you subscribe to the Calling Line Identification network
service your phone may display the caller’s number or
name when the phone rings.
For more details, refer to “Availability of Network Services”
Adjusting the Earpiece Volume
•
During a call, press ! or " to
decrease or increase the ear-
piece volume level.
Last Number Redial
•
Clear the display, then press SEND SEND.
Last 15 Dialed Calls
•
Clear the display, press SEND, then !. Press !
repeatedly until you see the number you want.
Then press SEND to dial it.
15
information.
Speed Dialing
•
Dial the number of the memory location (1-75) where
the phone number is stored, then press SEND.
You can also enter a stored name then press SEND.
The phone dials the number stored with that name.
If the memory location is empty, the message LOCATI ON
EMPTY appears.
1-Touch Dialing
If 1-Touch Dialing is set to On, you can dial the phone
number stored in any of the memory locations 1-8 by
pressing a single key:
•
Hold the required number key (1-8) for 2 seconds.
Note: Location 1 is recommended to be used as the Voice
Mailbox Number. Location 9 cannot be used for 1-Touch
Dialing to any number other than the preprogrammed
emergency number.
Emergency 9 Dialing
The 9 Key is reserved for an Emergency Number that is
programmed into your phone by your dealer.
•
Press and hold 9 for 2 seconds.
Emergency 9 Dialing must be set On for this to work!
16
Note: Official emergency numbers vary by location
(e.g., 911 or another official emergency number).
However, only one emergency number is programmed
into your phone to be dialed automatically by Emergency
9 Dialing, and this may not be the proper number in all
circumstances.
Note: Emergency 9 Dialing does not operate when
Keyguard is activated. However, an emergency call can
be made without deactivating Keyguard by entering the
whole emergency number programmed into your phone
and then pressing SEND.
Keyguard
•
•
To activate Keyguard, press and hold END (or press
MENU then ∗).
To deactivate Keyguard, press MENU then ∗.
Keyguard locks the keypad to prevent accidental
keypresses (e.g. when the phone is in a pocket or a bag).
KEYGUARD ACTI VE remains (or reappears) on the dis-
play until any key is pressed or Keyguard is deactivated.
Answering a Call with Keyguard Active
•
Press SEND.
During the call, the keypad remains unlocked and the
phone can be used normally. After the call is ended,
Keyguard automatically becomes active again.
The phone cannot be switched off when Keyguard is
active. However, if the phone is ringing and Keyguard is
active, you can press PWR to switch off the phone while it
is ringing.
17
Note: When Keyguard is activated, calls may be possible
to the emergency number programmed into your phone
(e.g., 911 or another official emergency number).
However, Emergency 9 Dialing does not operate.
Making an Emergency Call with
Keyguard Active
•
Enter the emergency number preprogrammed in your
phone and press SEND.
The emergency number is displayed only after you have
entered the last digit of the number.
Calling Card Calls
If you use the phone’s Calling Card storage feature
the method described below to charge long distance
charges to a Calling Card. You won’t need to enter Calling
Card information every time you want to make a card call.
Note: No physical credit cards are needed in order to
direct the call charges to the credit card; however you
must first store and select a Calling Card with Menu 5 2!
Note: If the Prepaid (Menu 9) option is activated, the
Calling Card menu is not available. Any calling card
information saved in your phone will be lost. If you
deactivate the service provider prepaid option, the Calling
Card menu becomes available again, but you must resave
any calling card information.
To make a Calling Card Call:
1
Enter the phone number of the party to be called.
2
Press and hold SEND for 2 seconds. The phone dis-
plays CARD CALL (and possibly the card name), then
displays WAI T FOR TONE, THEN PRESS ‘ OK’ .
18
3
4
When you hear a tone or voice prompt, press OK or
SEND. The phone may ask you again to WAI T FOR
TONE, THEN PRESS ‘ OK’ .
If you get another tone or voice prompt, press SEND
again.
The call is then made, and the phone displays CARD
CALL and the name of the card (if you have entered one).
It is also possible to make manual card calls by using
Touch Tones (DTMF) through your Calling Card Operator.
You can make calling card calls in conjunction with PIN
calls.
PIN Calls
PIN Call is a network security feature that requires a PIN
Code every time you make a call. You can activate or
deactivate it and specify the numbers in your PIN Code.
Please check with your operator for the availability of PIN
Calling in your network.
Note: If you are using the phone in an area that doesn’t
require PIN dialing, deactivate PIN Call.
Activating PIN Call
1
Enter * # 7 4 6 2 2 5 5 # (spells PINCALL).
2
The phone asks for your four-digit
PIN Code, which is provided by
your network operator. Enter your
PIN code and press OK.
The phone briefly displays PI N
CALL ON.
19
Making PIN Calls
1
Make the call as usual (refer to “Making a Call” on
The phone displays PI N CALL.
2
After you hear a tone, press SEND again.
The phone displays SENDI NG PI N . . . . If the
message remains on the display, press SEND again to
resend the PIN code. Wait for your call to be
connected.
Note: If you’re in a network that doesn’t support PIN Calls,
but your phone has PIN Call On, the phone still tries to
send a PIN. Press CLR to end the PIN Call attempt.
Note: When the phone is set to PI N CALL ON, an
emergency call to the emergency number programmed
into your phone (e.g., 911 or another official emergency
number) will be dialed as a normal call without the PIN
code request.
Deactivating PIN Call
•
Follow the steps in “Activating PIN Call”, but don’t
enter your PIN Code at the prompt; just press OK.
The phone briefly displays PI N CALL OFF.
Voice and Text Messages
If you subscribe to voicemail, callers will be able to leave
you voice mail messages which you can recall from your
voice mailbox.
If you have purchased the Nokia 252N and subscribe to a
text message network service, callers may send you short
text messages that you can read on your phone’s display.
20
What is Debit Mode?
®
To activate your phone through TRACFONE prepaid
service, call the toll free number on the card included with
this Owner’s Manual.
If you activate your phone through TRACFONE prepaid
on the features available.
Important note: You cannot activate your phone
through TRACFONE if you already have an existing cellular
service contract.
Note: If you activate your phone through TRACFONE,
contact TRACFONE Customer Service with questions
regarding any of your phone’s prepaid features.
Or, your service provider may offer prepaid service
compatible with your new Nokia phone. See “Prepaid
(Menu 9)” on page 59 for features that may be available to
you. Contact your service provider for details.
21
5. The Phone Book
The Phone Book can store up to 75 phone numbers and
corresponding names. It also has a “notepad” where you
can store one additional number and name.
The maximum number of phone book entries depends on
how much information you store in each location. Stored
phone numbers can be up to 32 digits long, and stored
names can be up to 30 characters long.
note about Memory Location 75.
Viewing and Entering Names
The ABC key is used to switch between displaying names
and numbers.
To enter names, search for names, and view names, press
ABC. The phone displays
to indicate that “alpha
mode” is selected; you can then use keys to enter letters
as well as numbers, and view the stored names rather
than numbers.
When a name is displayed, you can also press ABC to see
the associated number.
Entering Letters
1
Press ABC to select alpha mode. You can then enter
letters by pressing the keypad keys a certain number
of times.
See the table on the next page.
2
To correct mistakes, press CLR repeatedly or press
and hold CLR to clear the whole display.
22
1
2
3
4
5
Key
press presses presses presses presses
1
A
D
G
J
1
B
E
1
C
F
I
1
2
3
4
5
6
S
8
Z
1
A
D
G
J
1
2
3
4
5
6
7
8
9
H
K
N
Q
U
X
L
O
R
V
Y
M
P
T
M
7
T
W
9
Moves the cursor to the next space
immediately.
∗
Adds a space between letters.
#
Entering Punctuation Marks
The ‘0’ key can be used to insert punctuation marks (and
0). Press 0 until you get to the punctuation mark you want:
- ? !
,
. : “ ‘ & $ (
)
0
The Cursor
The cursor appears at the end of an entry for your
convenience when entering, editing or erasing an entry.
Note from the table above that you can either wait for the
timer to move the cursor to the next space or you can
press ∗ to force it to the next space.
23
Saving Numbers and Names
Quick Save
1
Enter the area code and phone number.
2
3
(Optional) Press ABC, then enter the name.
Press OK. When SAVE I N LOCATI ON? is displayed,
press OK.
The phone stores the number in the first empty memory
location. The memory location is shown in the display’s
upper right corner.
Identical names cannot be stored in memory. If you try to
store a name that is already stored, the phone displays
SAVE I N LOCATI ON n? (with n being the location cur-
rently containing the matching name). To confirm, press
OK. Then, the phone asks if you want to replace the entry.
To do this, at REPLACE? (followed by the name), press
OK.
If you don’t want to replace the contents, re-enter the in-
formation using a slightly different name, then save again.
Note: You can also use Menu 1 to find, save, edit, and erase
Memory Location 75
This is a special memory location. If you store a number in
location 75, you can make calls to that number even if the
Special Characters in Stored Numbers
In stored numbers, you can include a 2.5 second pause
(‘p’ character), a wait (‘w’ character), or a link to another
location (‘+’ character). This allows the automatic sending
of Touch Tones.
24
For more information on using these special characters
•
To enter a Pause (p), press ∗∗∗.
Note that a ‘p’ appears on the
display, but this is different from
just keying in the letter ‘p’.
•
•
To enter a Wait (w), press ∗∗∗∗.
To enter a link to another location, press ∗∗. A ‘+’ sign
will appear on the display. A ‘+’ in the middle of a
string links to another location.
Note: A ‘+’ at the beginning of a number is used for
more information.
Joining two locations for long Touch Tone
strings:
1
Enter the Touch Tone string and store it in the phone
book. Remember its location number.
2
3
4
Recall the phone number (assuming it’s already
stored) and remember its location number.
Press ∗∗. The ‘+’ character is displayed after the
phone number.
Enter the location number (one or two digits) of the
Touch Tone string (from Step 1). Store the new con-
tents (phone number, ‘+’, and Touch Tone location).
When the phone displays SAVE I N LOCATI ON?
enter the location number from Step 2 and press OK.
For details on sending Touch Tones, see “Sending Touch
25
Making a call using the two joined locations:
1
Recall the first location and press SEND. This dials the
phone number, but the dialing stops at the ‘+’
character.
2
When the call is established, press MENU SEND.
The phone will automatically send the Touch Tone
string in the second location (which is displayed).
Finding Numbers and Names
Finding numbers
•
With the display clear of numbers or names,
press ! repeatedly to scroll the numbers stored in
the Phone Book.
Phone numbers are displayed in order of location number.
To view the name stored with the number displayed, press
ABC.
Finding names
•
With the display clear of numbers or names,
press ABC then ! repeatedly to scroll the names
stored in the Phone Book.
Names are displayed in alphabetical order. To view the
number stored with the name displayed, press ABC.
Using the Notepad Memory
Saving a number and name in the
Notepad
•
Enter the number and name, then press OK. At SAVE
I N LOCATI ON?, press # then press OK.
26
Viewing information in the Notepad
•
With the display clear of numbers or names,
press # then ! to view the number. To view the
name stored with the number, press ABC.
Moving a Name and Number
1
Recall the name and number from memory. Press OK.
2
At SAVE I N LOCATI ON?, enter the new location
number then press OK. The phone will display MOVE?
3
Press OK to move (the phone displays MOVED and
the remaining available memory), or press CLR to exit
without moving.
Erasing a Name and Number
Editing a Name and Number
27
6. The Menu
The phone’s menus and submenus give you access to
many features and ways to customize your phone.
You can use the menus and submenus either with the
‘Menu then OK Method’ or the ‘Shortcut Method’.
menus follow.
“MENU then OK” Method
1
Press MENU to enter the menu.
2
3
Press ! or " to scroll through menu choices.
Press OK to choose a menu.
If there are submenus: press ! or " to scroll through
the submenu choices. Press OK to enter a submenu.
4
The current setting is displayed. Press ! or " to
scroll through the other choices. Press OK to select
one, or press END to exit the menus without changing
anything.
Some menus require you to enter your lock code or
security code.
Note: To backstep a menu level at a time, press CLR.
To exit the Menu, press END or press and hold CLR.
28
Shortcut Method
The menus and submenus are numbered, so you can
access them by their number:
1
Press MENU to enter the menu.
2
Press the number of the menu you want (1-6) within
4 seconds. (Also, If there are submenus, press the
submenu number within 4 seconds.) The current
setting (if applicable) is displayed.
3
Press ! or " to scroll through other settings.
Press OK to select a setting or press CLR to exit the
menus without changing the settings.
Note: If you use the shortcut method, the display shows a
‘_’ before the menu or submenu number in the top right-
hand corner of the display.
Also, if you use the shortcut method to access Menu 3 1,
there is a 5-second delay before the menu appears. To
bypass this delay, press MENU 3 1 OK OK.
Using the Menu During a Call
If you press MENU during a call, the phone gives you the
access to other menu items, just press and hold MENU
for a couple of seconds. Then use the menus as you
normally would.
29
List of Menu Functions
1 Phone Book
7 Messages**
1
Find Name
1
2
3
Read Messages
Erase Messages
Message Alert Tone
2
3
4
5
Save Name & Number
Edit Name or Number
Erase from Phone Book
Phone Book Status
8 Debit (TRACFONE only)
1
2
Timetank Info
Checksum
2 Call Log
1
Dialed Calls
Received Calls
Missed Calls
Erase all Recent Calls
Call Timers
9 Prepaid (if available)
2
3
4
5
1
Check Balance
2
3
4
Add Money to Account
Prepaid Card
Save Access Numbers
3 Phone Settings
1
In-Call Menu
Ringing Options
Ringing Volume
Ringing Tone
Keypad Tones
Lights
1-Touch Dialing
Emergency 9 Dialing
Language
This is available only during calls.
Give the MENU key a short
press to access the options:
‘Mute’ and ‘Send DTMF’.
2
3
4
5
6
7
8
9
Reminder Message
Displays a personalized message
when you switch your phone on.
Phone Number
10 Automatic Answer
11 Automatic Redial
* This option is not available if
Prepaid (Menu 9) is activated.
4 Security Settings
1
2
3
Change Lock Code
Change Security Code
Restore Factory Settings
**Messages menu is
available on Nokia 252N only.
Messages feature depends
on network and subscription.
5 Call Settings
1
2
Calling Options
Calling Card*
6 Lock Phone
Prevents outgoing calls and
access to all phone functions.
30
Phone Book (Menu 1)
To access Menu 1, press MENU then OK.
Find Name (Menu 1 1)
1
Press MENU then OK.
2
You’ll see FI ND NAME. Press
OK again. The phone prompts
you to enter a name.
3
Enter the first few letters of the
name, then press !, or just
press !#to scroll through stored names.
Note: To see stored numbers, press ABC, then press !
to scroll through them.
Save Name & Number (Menu 1 2)
1
Press MENU then OK then ! to scroll to SAVE
NAME & NUMBER. Press OK.
2
Enter name and press OK.
Enter number and press OK.
The phone suggests a location
for saving the entry.
3
Press OK, or enter another
location number then press OK. The phone displays
SAVED and the remaining available memory.
Edit Name or Number (Menu 1 3)
1
Recall the number from memory.
2
Press MENU then OK then ! to scroll to EDI T
NAME OR NUMBER. Press OK.
31
3
4
5
Edit the name: use the CLR key to delete characters,
use ! and " to move the cursor, and enter new
characters as required.
Edit the number: press ABC. Use the CLR key to
delete digits, use ! and " to move the cursor, and
enter new digits as required. Press OK.
At SAVE I N LOCATI ON? press
OK. If you did not change the
name, or the name you have
entered matches one already
stored, then REPLACE? will be
displayed; press OK to replace the contents with the
new (edited) name and number.
Erase From Phone Book (Menu 1 4)
Note: Be careful when erasing – it can’t be undone!
1
Press MENU then OK then ! to scroll to ERASE
FROM PHONE BOOK. Press OK.
2
Press !#to move the pointer to
your choice. Press OK to choose
it.
If you choose Er as e Al l , the phone
asks you to confirm. Press OK when you see ARE YOU
SURE?, or press CLR to exit without erasing.
If you choose One by One, the phone displays Er as e
name: . Either enter the first few letters of the name then
press !, or just press ! to scroll through stored names.
Press ABC to see phone numbers to erase. When you see
the name or number you want to erase, press OK, or
press CLR if you change your mind and do not want to
erase.
32
Phone Book Status (Menu 1 5)
1
Press MENU then OK then ! to
scroll to PHONE BOOK STATUS.
Press OK.
2
The phone displays the percent-
age of memory available.
Call Log (Menu 2)
To access Menu 2, press MENU then !. You’ll see CALL
LOG; press OK.
Dialed Calls (Menu 2 1)
The phone automatically stores the last 15 numbers you
called or attempted to call. The same phone number isn’t
stored twice in the list. When you dial a number that already
exists in the list, the dialed number is moved to the top.
The Dialed Calls list remains in the phone's memory when
the phone is switched off. If you want to erase it, use
Menu 2 4.
1
Press MENU !. You’ll see CALL LOG; press#OK.
2
You’ll see DI ALED CALLS.
Press OK again.
3
Press ! to scroll through the last
15 numbers you have dialed.
Each phone number in the list
has a number which shows in the top right corner of
the display; e.g. ‘2L’ - ‘L’ stands for last (dialed) call.
Press SEND to dial one of the numbers.
33
Received Calls (Menu 2 2)
The phone automatically stores the callers’ numbers of the
last 15 calls you received and answered (if network sup-
ports this feature, and the callers’ numbers were received
from the network – refer to your service provider for more
details). The same phone number isn’t stored twice in the
list.
When you dial a number in the Received Calls list it re-
mains in this list, and it is also added to the Dialed Calls list.
The Received Calls list remains in the phone's memory
when the phone is switched off. If you want to erase it, use
Menu 24.
1
Press MENU !. You’ll see CALL LOG; press#OK.
2
Press ! to scroll to RECEI VED
CALLS. Press OK.
3
Press ! to scroll through the
phone numbers of the last 15
received calls.
Each phone number in the list has a number which is
shown in the top right corner of the display;
e.g., ‘2A’ – ‘A’ stands for answered (received) call.
Press SEND to dial one of the numbers.
To store one of the numbers in the Phone Book, recall the
number from the list, then press OK; when SAVE I N
LOCATI ON ‘ n’ is displayed, press OK again.
Missed Calls (Menu 2 3)
The phone automatically stores the callers’ numbers and
names of the last 15 calls you missed (if network supports
this feature, and the callers’ numbers were received from
the network – refer to your service provider for more de-
tails). The same phone number isn’t stored twice in the list.
34
When you dial a number in the Missed Calls list it is deleted
from this list, and it is added to the Dialed Calls list.
The Missed Calls list remains in the phone's memory when
the phone is switched off. If you want to erase it, use
Menu 24.
1
Press MENU !. You’ll see CALL LOG; press#OK.
2
Press ! to scroll to MI SSED
CALLS. Press OK.
3
Press ! to scroll through the
phone numbers of the last 15
missed calls.
Each phone number in the list has a number which is
shown in the top right corner of the display;
e.g., ‘2U’ – ‘U’ stands for unanswered (missed) call.
Press SEND to dial one of the numbers; this number
will then be deleted from the list.
To store one of the numbers in the Phone Book, recall the
number from the list, then press OK; when SAVE I N
LOCATI ON ‘ n’ is displayed, press OK again.
Erase All Recent Calls (Menu 2 4)
Note: This menu erases all numbers in the Dialed Calls,
Missed Calls and Received Calls lists, and can’t be
undone!
1
Press MENU !. You’ll see CALL LOG; press#OK.
2
Press ! to scroll to ERASE ALL
RECENT CALLS. Press OK.
3
The phone asks ARE YOU
SURE? Press OK to erase, or
press CLR to exit without erasing.
35
Call Timers (Menu 2 5)
1
Press MENU !. You’ll see CALL LOG; press#OK.
2
3
Press ! to scroll to CALL TI MERS. Press OK.
Press ! to scroll through the
options. Press OK to choose the
one you want. (You’ll need your
security code to clear the timers.)
LAST CALL shows the duration of the last call in hours,
minutes, and seconds. If you are in a call, the phone
shows the duration of the call in progress. (Make sure you
hold MENU for a couple of seconds during a call to get to
the regular menu and not the In-Call menu.)
ALL CALLS shows the total amount of time spent on
calls since the timer was last reset. ALL CALLS applies
to the phone number currently selected for your phone.
LI FE TI MER s hows the total amount of time you have
spent on calls in hours and minutes. This number cannot
be reset. (You can also select Life Timer by pressing and
holding the # key for about 4 seconds.)
CLEAR TI MERS resets all the timers to zero (except the
Li f e Ti mer ). Note: CLEAR TI MERS cannot be
undone!
Note: The actual invoice for calls by your cellular service
provider may vary, depending upon network features,
rounding-off for billing, taxes and so on.
Phone Settings (Menu 3)
To access Menu 3, press MENU, then !#until you see
PHONE SETTI NGS. Press OK.
36
Ringing Options (Menu 3 1)
You can choose how you want the phone to indicate that
there is an incoming call.
1
Press MENU then !#until you see PHONE SETTI NGS.
Press OK.
2
You’ll see RI NGI NG OPTI ONS
and the current setting. Press OK
if you want to change it.
3
Press !#to move the pointer to
the choice you want. Press OK to
select one.
For Ri ng+Vi br a or Vi br at e to
work, you need the Vibra battery
(BML-8).
If you choose Si l ent , the phone
displays SI LENT when you aren’t
using the other functions of the phone. This message is to
remind you that the ringing tone is set to Off.
Note: When SI LENT is selected, all tones, except for the
charger-connected tone, are also switched off.
If you choose I ncr eas i ng, ringing will start at the lowest
volume level, and then increase to the highest level.
Ringing Volume (Menu 3 2)
With this menu you choose the ringing volume. As you
scroll through each of the 5 volume levels, the phone rings
so you can hear each level.
1
Press MENU then !#until you see PHONE SETTI NGS.
Press OK.
37
2
3
Press ! to scroll to RI NGI NG
VOLUME and the current setting.
Press OK if you want to change it.
Press !#to move the pointer.
Press OK for the ringing volume
you want.
Ringing Tone (Menu 3 3)
There are 6 different ring tones to choose from. As you
scroll through each type, the phone rings so you can hear
each one.
1
Press MENU then !#until you see PHONE SETTI NGS.
Press OK.
2
Press ! to scroll to RI NGI NG
TONE and the current setting.
Press OK if you want to change it.
3
Press !#to move the pointer.
Press OK for the ringing tone you
want.
Keypad Tones (Menu 3 4)
When you press the buttons on your phone, the phone
beeps (the sound depends on which key you press). With
this menu, you can choose between three volume levels
or you can turn the keypad tones off.
1
Press MENU then !#until you see
PHONE SETTI NGS. Press OK.
2
Press ! to scroll to KEYPAD
TONES and the current setting.
Press OK if you want to change it.
3
Press !#to move the pointer. Press OK to choose the
one you want, or select Off.
38
Note: You can still send Touch Tones even when the
keypad tones are switched off.
Note: Keypad tones are set to Off when you choose
Lights (Menu 3 5)
The keypad and phone display have lights to make them
easy to read. This menu allows you to set the phone's
lights On or Off.
1
Press MENU then !#until you see PHONE SETTI NGS.
Press OK.
2
Press ! to scroll to LI GHTS and
the current setting. Press OK if
you want to change it.
3
Press !#to move the pointer.
Press OK to choose On or Off.
Lights On
The keypad and display backlights are on for 15 seconds
after the last keypress.
Lights Off
The lights are off permanently, except if Silent ringing is
selected. Then they flash to indicate an incoming call.
1-Touch Dialing (Menu 3 6)
This menu gives you the option of dialing memory loca-
tions 1-8 by pressing and holding a single number key for
2 seconds (location 1 is recommended to be used for the
Voice Mailbox Number). For example, pressing and
holding 5 dials the number stored in location 5.
1
Press MENU then !#until you see PHONE SETTI NGS.
Press OK.
39
2
3
Press ! to scroll to 1- TOUCH
DI ALI NG and the current set-
ting. Press OK if you want to
change it.
Press !#to move the pointer.
Press OK to choose On or Off.
With 1-Touch Dialing On, you can dial the number stored
in any of the locations 1 to 8, by pressing and holding the
corresponding number key. If you press and hold 1, the
phone dials your voice mailbox number if you have stored
it in this location.
Note: 1-Touch Dialing does not operate when Keyguard is
On, or when a call is already established.
If you press and hold 9, the phone attempts to make a call
to the emergency number pre-programmed into your phone
if you have Emergency 9 Dialing (Menu 3 7) set to On.
Emergency 9 Dialing (Menu 3 7)
You may dial the emergency number programmed in your
phone by your dealer, by pressing and holding the 9 key,
only if Menu 3 7 is set to On.
1
Press MENU then !#until you see PHONE SETTI NGS.
Press OK.
2
3
Press ! to scroll to EMERGENCY 9 DI ALI NG and
the current setting. Press OK if you want to change it.
Press !#to move the pointer. Press OK to choose On
or Off.
Also, you can make an emergency call by entering the
emergency number (such as 911) and pressing SEND.
40
Language (Menu 3 8)
The menus and messages can be displayed in English,
French, Spanish, or Portuguese.
1
Press MENU then !#until you see PHONE SETTI NGS.
Press OK.
2
Press ! to scroll to LANGUAGE
and the current setting. Press OK
if you want to change it.
3
Press !#to move the pointer to
your choice. Press OK to select
an option.
Phone Number (Menu 3 9)
Your phone can have two different telephone numbers.
This menu lets you choose which telephone number to use.
Note: In order to have two different telephone numbers,
you must subscribe to them through your cellular
operator(s).
1
Press MENU then !#until you see PHONE SETTI NGS.
Press OK.
2
Press ! to scroll to PHONE
NUMBER and the current phone
number. Press OK if you want to
change it.
3
Press !#to move the pointer to
the number you want (if there are
two available). Press OK.
Note: If only one phone number is
programmed into your phone, you’ll only see that number
in this menu.
41
The phone can’t use both numbers at the same time and
you can’t change the number during a call.
If your phone is set to your first number, you can only re-
ceive calls via that number. You may be able to forward
calls from your second number to your first number so you
don’t miss any calls, if this service is available from your
cellular service provider. For more information, please
contact your cellular service provider.
Automatic Answer (Menu 3 10)
Note: This feature applies only if the phone is in a
handsfree car kit.
With Automatic Answer On, the phone automatically
answers after 4 seconds.
1
Press MENU then !#until you see PHONE SETTI NGS.
Press OK.
2
Press ! to scroll to AUTOMATI C
ANSWER and the current setting.
Press OK if you want to change
it.
3
Press !#to move the pointer.
Press OK to choose On or Off.
Automatic Redial (Menu 3 11)
Sometimes the cellular network is busy and your call can’t
go through. You get a SYSTEM BUSY. . . message and
are asked to redial. If Automatic Redial is set to On, the
phone automatically tries 3 more times to connect the call.
If the call connects, the phone beeps to notify you.
1
Press MENU then !#until you see PHONE SETTI NGS.
Press OK.
42
2
3
Press ! to scroll to AUTOMATI C
REDI AL and the current setting.
Press OK if you want to change
it.
Press !#to move the pointer.
Press OK to choose On or Off.
Security Settings (Menu 4)
This menu lets you change your phone’s security and lock
codes, which are required for certain functions. You can
also reset the phone’s menus to their factory settings.
Note: You need your security code to access this menu.
The default security code is 12345.
To access Menu 4, press MENU, then !#until you see
SECURI TY SETTI NGS. Press OK.
The phone asks for your security code.
Enter your 5-digit security code and
press OK.
Change Lock Code (Menu 4 1)
The lock code is required when you want to lock your
Note: The phone’s default lock code is 1234.
1
Press MENU then !#until you see SECURI TY
SETTI NGS. Press OK.
2
Enter your security code and press OK.
43
3
4
You’ll see CHANGE LOCK
CODE. Press OK to change it.
Enter a new 4 digit lock code.
Press OK.
The phone asks you to verify your
new lock code. Type in the new lock code again and
press OK. The phone briefly displays LOCK CODE
CHANGED.
Change Security Code (Menu 4 2)
The security code allows access to the lock code and
certain submenus, so it should be kept in a secret and safe
place, separate from the phone.
1
Press MENU then !#until you see SECURI TY
SETTI NGS. Press OK.
2
3
Enter your security code and press OK.
Press ! to scroll to CHANGE
SECURI TY CODE. Press OK to
change it. Enter a new 5-digit
security code. Press OK.
4
5
When the phone asks you to
verify your new security code, enter it again and press
OK.
The phone briefly displays SECURI TY CODE
CHANGED.
Restore Factory Settings (Menu 4 3)
This function resets the phone’s menus to their factory
settings.
Note: The lock code and security code are not changed
when you reset the menu settings.
44
1
Press MENU then !#until you see SECURI TY
SETTI NGS. Press OK.
2
3
Enter your security code and press OK.
Press ! to scroll to RESTORE FACTORY SETTI NGS.
Press OK to reset them.
4
5
The phone asks you to confirm.
Press OK to reset or press CLR
to exit without resetting.
If you press OK, the phone briefly
displays SETTI NGS RESTORED.
Call Settings (Menu 5)
This menu lets you store calling card information in your
phone, and set up calling restrictions.
To access Menu 5, press MENU, then !#until you see
CALL SETTI NGS. Press OK.
Calling Options (Menu 5 1)
This menu lets you set your phone so that it can only make
the types of calls you specify, or only in certain types of
networks.
Note: When calls are restricted, calls may be possible to
the emergency number programmed into your phone
(e.g., 911 or another official emergency number) including
calls by emergency 9 dialing.
Carrier Selection (Menu 5 1 1)
Your phone uses a carrier network (also called a cellular
system) to make and receive calls. Generally you sign up
for service with a particular “carrier” (your cellular service
provider). This is called your “Home system” and usually
you want the phone to use it.
45
But there may be times when you can’t or don’t use your
Home system (for example when you travel). Then, there’s
usually more than one network your phone can work in.
But which one should it work in? The point of the Carrier
Selection menu is to help your phone make the best
choice for you.
A simple fact to know: all cellular systems are either type
“A” or “B”. So your “Home system” is either an “A” or “B”
system. Ask your cellular service provider or dealer which
type yours is.
1
Press MENU then !#until you see CALL SETTI NGS.
Press OK. Press ! until you see CALLI NG OPTI ONS.
Press OK.
2
Press ! to scroll to CARRI ER
SELECTI ON and the current
setting. Press OK if you want to
change it.
3
4
The phone asks for your security
code. Enter it and press OK.
Press ! to move the pointer to
the option you want (described
below). Press OK to select it.
Pr ef er r ed - Your dealer can pro-
gram a list of “preferred” networks
into your phone. If your dealer has done this, when you
choose Pr ef er r ed your phone looks first for your home
system, then a network in the preferred list, then a network
of the same “type” (A or B) as your home system, then a
network of the opposite “type” as your home system.
46
If your dealer has not programmed this list into your
phone, you can still use the Pr ef er r ed option. The
phone will look first for your home system, then a network
of the same “type” as your home system.
Non- Pr ef er r ed - Your phone will choose a network
that is of a different “type” than your Home system.
Any - The phone first looks for your home system, then a
network of the same “type” as your home system, then a
network of the opposite “type” as your home system.
Home Onl y - The phone only looks for service on the
Home system. It won’t choose any other network, so if
you’re out of your Home system, you won’t have service
(NO SERVI CE).
The table below shows how the phone’s display changes
according to which network the phone uses.
If the phone is
using this
The display
shows:
The display says:
network:
Home system
Blank, or name of
Home system
(solid)
Preferred network
PREFERRED, or
name of Preferred
network
(flashing)
Home-type (phone (blank)
has preferred list)
ROAMI NG
Home-type (no
preferred list in
phone)
ROAMI NG
(flashing)
(blank)
Non-Home-type
NON- PREF.
47
Allowed Calls (Menu 5 1 2)
1
Press MENU then !#until you see CALL SETTI NGS.
Press OK. Press ! until you see CALLI NG OPTI ONS.
Press OK.
2
Press ! to scroll to ALLOWED
CALLS and the current setting.
Press OK if you want to change
it.
3
4
The phone asks for your security
code. Enter it and press OK.
Press ! to move the pointer to
the option you want (described
below). Press OK to select it.
Al l ow al l - There are no restric-
tions on outgoing calls.
Nat ’ l onl y - You can only make calls within your own
country; you cannot make international calls.
Local onl y - You can only make local calls, or calls to
toll-free numbers beginning with 1800, 1888, or 1877.
You cannot make national calls (prefixed with 1) or inter-
national calls (prefixed with 011).
Mem. onl y - You can only make outgoing calls to
numbers stored in memory locations 10-14.
Note: You cannot store any numbers in the phone
directory when Mem. only is selected.
I ncomi ng - You can only receive incoming calls; your
phone will not allow outgoing calls.
48
Calling Card (Menu 5 2)
Note: If you activate the service provider prepaid option,
this menu is not available. Any calling card information
saved in your phone will be lost. If you deactivate the
service provider prepaid option, the Calling Card menu
becomes available again, but you must resave any calling
card information.
With this menu you store calling card information for up to
2 cards in your phone. Then you can make calling card
calls without having to enter the calling card information
each time.
To make a calling card call, see “Calling Card Calls” on
Remember, to use the automated method of making cal-
ling card calls, you must have entered all the necessary
card details and selected the card (using this menu). If only
the details for one card are entered, there is no need to
use the Select feature. But, if you then add the details of
another card, the second card will automatically become
the card in use. Only one card can be active at a time.
You may enter a card name for each card, but this is
optional. This name is only used for card identification on
the phone display, and has no effect on the sending
sequence. ‘Card A’ and ‘Card B’ will be replaced by the
names you enter.
Card information may be found on your calling card. If you
need further information about specific dialing sequences,
contact your calling card company.
To Enter or Change Calling Card Information
1
Press MENU then !#until you see CALL SETTI NGS.
Press OK.
49
2
3
You’ll see CALLI NG CARD and
the currently selected card. Press
OK to change it.
Use ! to move the pointer to
None, Car d A or Car d B, then
press OK. When the phone asks for your security
code, enter it and press OK.
If you select None, the phone briefly displays NO
CARD SELECTED, and no card is selected.
Note: If you’ve already stored card information, and
then later select None, the active card is deselected.
However, stored card information is left intact.If you
select Car d A or Car d B, and you’ve never entered
information for the card before, skip to Step 5.
4
If you’ve already entered informa-
tion for a Card, you then have the
option to Sel ect , Edi t , or
Er as e the card. Use ! to move
the pointer to the option you
want, and press OK.
Sel ect chooses this card as the one to use.
The phone briefly displays SELECTED.
Edi t allows you to change already-entered
information, described in Steps 5 and 6 on next page.
Er as e erases the stored information. To verify that
you want to do this, press OK at the ERASE?
prompt. Press CLR if you don’t want to erase the
stored information.
5
The phone prompts you to
SELECT DI ALI NG
SEQUENCE. Press OK.
50
Press ! to scroll through the 4 dialing sequence
options, and press OK to choose:
Acces s No. + Phone No. + Car d No.
Use for cards that require you to enter a 1-800
access number first, then require you to enter a
phone number after you hear a tone, then a card
number after you hear another tone.
Acces s No. + Car d No. + Phone No.
Use for cards that require you to enter a 1-800
access number first, then require you to enter your
card number after you hear a tone, then the phone
number after you hear another tone.
10xxx + Phone No. + Car d No.
Use for cards that require you to enter an access
number (beginning with 10 then 3 digits), followed by
the phone number after you hear a tone, then a card
number after you hear a tone.
0 + Phone No. + Car d No.
Use for cards that require you to enter 0, then the
phone number after you hear a tone, then a card
number after you hear a tone.
6
The phone then prompts you for other card informa-
tion, which may include: SELECT PREFI X, Car d
No: , and Car d name: . At each of these prompts,
press OK.
For SELECT PREFI X, use ! or " to move the
pointer to the prefix that your calling card requires you
to enter before the phone number. Then press OK.
For Acces s No: , Car d No: , and Car d name: ,
enter the information then press OK.
The phone briefly displays CARD READY FOR USE, and
uses the card for which you just entered information.
51
Lock Phone (Menu 6)
When you lock your phone, you cannot make outgoing
calls (except to the number stored in location 75 and the
emergency number programmed into your phone).
Also, you cannot access the phone’s memory or menu.
You can receive incoming calls as usual.
To make a call to location 75 when the phone is locked,
press ! then SEND. To call the emergency number, enter
the entire emergency number then press SEND.
1
Press MENU then !#until you see LOCK PHONE.
Press OK.
2
3
The phone asks you to Ent er
l ock code.
Enter the lock code and press
OK. The phone displays PHONE
LOCKED.
LOCKED remains on the display to remind you that the
phone is locked. To unlock the phone, press MENU and
the phone will prompt you for the lock code. Enter it and
press OK.
Messages (Menu 7)
NOTE: This menu is available on the Nokia 252N
only. The messages feature depends on network
and subscription.
To access Menu 7, press MENU, then#! until you see
MESSAGES. Press OK.
52
Read Messages (Menu 7 1)
The phone automatically stores the last 20 short text
messages you have received in the Read Messages list.
(You can receive text messages if the network supports
this service, and if you subscribe to this service – refer to
your service provider for more information). This menu lets
you scroll through and read the stored messages.
Stored messages remain in the phone's memory when
the phone is switched off. The same message isn’t stored
twice in the list.
If you want to erase a message, use Menu 7 2.
1
Press MENU, then#! until you
see MESSAGES. Press OK.
2
Press ! to scroll to READ
MESSAGES. Press OK. The
display will show MESSAGE( S)
RECEI VED if there are new ones or the first (read)
message in the list.
3
Use ! or " to scroll to the
message you want to read;
e.g., NEW: CALL HOME).
NEW denotes an unread
message, whereas OLD would
denote a previously read message.
Each message has a number which shows in the top
right corner of the display. The newest message is 1.
After you have read the last message, the phone
displays ***END***.
53
Erase Messages (Menu 7 2)
This menu lets you erase any of the stored messages.
Note: This menu erases messages you select, and cannot
be undone!
1
Press MENU, then#! until you see MESSAGES.
Press OK.
2
Press ! to scroll to ERASE
MESSAGES. Press OK.
3
Use ! or " to scroll to the mes-
sage you want to erase. Press
OK. When ERASE? is displayed,
press OK again. The phone will
briefly display ERASED. The list of
stored messages is then re-ordered and the next
message is displayed. If the list is empty,
***END*** is displayed.
Message Alert Tone (Menu 7 3)
This menu lets you set the type of alert tone you hear when
you receive a text or voice message.
1
Press MENU, then#! until you see MESSAGES.
Press OK.
2
Press ! to scroll to MESSAGE
ALERT TONE and the current
setting. Press OK if you want to
change it.
54
3
Press ! to move the pointer to
the option you require: Short,
Long, Vibra Only or Off. Press OK
to choose it.
These options are described below:
Shor t - causes the phone to beep 3 times when you
receive a text or voice message.
Long - causes the phone to beep for 15 minutes when
you receive a voice or text message. To stop the beeping,
press any key except the PWR or the ! or " (volume) keys.
Vi br a Onl y - causes the phone to vibrate (if you are
using the Ultra Extended Vibra battery BML-8) when you
receive a voice or text message.
Of f - means the phone won’t beep (or vibrate) when you
receive messages.
Debit (Menu 8)
If you activate your phone as prepaid
through TRACFONE prepaid service,
your phone will have an additional
menu item called DEBIT.
If you activate the prepaid option,
your phone functions the same way as it did before, with
some additional features. These features are listed and
explained in this section.
To access the Debit menu, press the MENU key, then
press "#once, the press OK. Press ! or " to scroll
through the menu options.
TI METANK I NFO shows you the amount of prepaid talk
time you have left in your phone.
55
At the TI METANK I NFO screen, press the OK key, and
your phone displays the number of units remaining
(indicated as U) as well as the date by which you should
redeem another prepaid cellular card.
CHECKSUM is a customer service only menu item, used for
debit verification.
Adding Units to Your Phone
Each time you want to add units to your phone, you must
purchase another TRACFONE Airtime Card and then
contact TRACFONE prepaid service.
Important note: You must add units to your phone
before the airtime card due date, or your service will be in-
terrupted and your phone number may be changed.
Switching On/Off
When you first turn your phone on,
REMEMBER AI RTI ME CARD DUE
and a date appear.
This reminds you that this is the date
you must purchase additional airtime
in order to retain your current phone
number and cellular service. The date
automatically updates once you add
units to your phone.
UNI TS and the number of units currently in your phone
appear after another few second pause. This number
automatically updates while you are in a call, at the end of
a call, and once you add units to your phone.
Note: When your phone displays the REMEMBER
AI RTI ME message, you can press any key to skip the
subsequent CARD DUE and UNI TS messages and ready
the phone for immediate use.
56
Making a Call
For complete information on making a call, refer to
Once you have placed a call your phone displays the
charge rate of units per minute, as well as a timer which
tracks the duration of the call expressed in minutes and
seconds.
Your phone has a grace period that begins when you
make a call and extends for an amount of time set by
TRACFONE prepaid service. The grace period exists only
on outgoing calls.
During the grace period you are not charged for the call.
Once the grace period expires, the charge rate of units per
minute is replaced by only the number of units remaining
in your phone (indicated as U).
When there are only ten minutes of talk time left in your
phone, your phone sounds a beep that continues once a
minute. If you hang up before the amount of time in your
phone expires, your phone continues to beep once a
minute during the next call.
If you try to make a call and there are no units left in your
phone, your phone beeps and displays the message
TI METANK EMPTY.
Ending a Call
For complete information on ending a call, refer to “Ending
Once you press END, your phone
displays the remaining units (indicated
as U) and the duration of the call
expressed in minutes and seconds.
57
Note: Due to rounding, there may be a difference between
the call time length shown on the screen after you termi-
nate a call and the call time length shown under the menu,
Call Timers.
Answering a Call
For complete information on answering a call, refer to
Note: Call Waiting may not be available if your phone is in
prepaid mode.
When you answer a call your phone displays the charge
rate of units per minute as well as a timer which tracks the
duration of the call expressed in minutes and seconds.
After three seconds the charge rate of units per minute is
replaced by only the number of units remaining in your
phone (indicated as U).
When there are only ten minutes of talk time left in your
phone, your phone sounds a beep that continues once a
minute. If you hang up before the amount of time in your
phone expires, your phone continues to beep once a
minute during the next call.
If there are no units left in your phone, your phone will not
ring for incoming calls.
Making a Calling Card Call
For complete information on making a calling card call,
While you are in a call, your phone displays the number of
units being used, as well as a timer which tracks the
duration of the call.
58
PIN Calls
For complete information on making a call with PIN call on,
refer to “PIN Calls” on page 19.
Once the call is connected, your phone displays the
number of units being used, as well as a timer which
tracks the duration of the call.
Emergency 9 Dialing
For complete information on 9 key emergency dialing,
When you make an emergency call, the amount of units
being used and the duration of the call are not tracked by
your phone.
This means you are not charged for 911 calls. Even when
there are no units in your phone, you are able to make 911
calls.
Prepaid (Menu 9)
Your service provider may offer prepaid service compatible
with your new Nokia phone. Contact your service provider
for details.
If you activate your phone as prepaid
through your service provider and
then activate the Prepaid menu, your
phone will have an additional menu
item called PREPAID.
Your phone functions the same way as it did before, with
some additional features. These features are listed and
explained in this section.
To activate prepaid feature available through your service
provider, enter the following sequence: *# 7766# .
59
To deactivate the prepaid feature available through your
service provider, enter the following sequence: *# 77633# .
To access the Prepaid menu, press the MENU key, then
press " to go immediately to the Prepaid menu. Press !
or " to scroll through the menu options.
Adding Money to Your Prepaid Account
ADD $ TO ACCOUNT allows you to add money to your
prepaid account.
Saving Your Access Number
Before you can add money to your account, you must
save the correct access number into your phone. Contact
your service provider for the access number.
1
Press MENU 9 4.
2
3
4
At SAVE ACCESS NUMBERS, press OK.
Press " once.
At Repl . No: , enter the replenish number given to
you by your service provider.
5
Press OK.
Adding Money to Your Account
1
Press MENU 9 2.
2
At Car d No: , enter your prepaid card number, then
press OK.
3
4
When your phone displays ADD $ TO ACCOUNT,
press OK.
When you hear the tone (and your phone displays
WAI T FOR TONE, THEN PRESS OK), press OK.
60
Checking Your Prepaid Balance
CHECK BALANCE allows you, free of charge, to check
your prepaid balance.
Contact your service provider for the toll-free balance
checking access number, which you must save in your
phone. If you try to check your balance before the correct
number is saved in your phone, the message NO ACCESS
NUMBER DEFI NED displays.
Saving the Balance Checking Number
1
Press MENU 9 4.
2
At SAVE ACCESS NUMBERS,
press OK.
3
4
5
At ENTER BALANCE NUMBER,
press OK.
At Bal No: , enter the balance
number given to you by your service provider.
Press OK.
Checking Your Prepaid Balance
Press MENU 9 1.
The balance checking number you saved is automatically
dialed.
Prepaid Calling Card
Note: This feature may not be available in all areas.
See your service provider for more information.
PREPAI D CARD allows you to save a prepaid card
number into your phone. Contact your service provider for
your prepaid card number.
Note: You can only have one prepaid card number saved
in your phone at a time.
Note: If you activate your phone as prepaid through your
service provider, the Calling Card menu option is not
available.
61
Saving Your Prepaid Card Number
1
Press MENU 9 3.
2
3
Scroll to Car d and press OK.
At Pr ef i x No: enter the prefix number given to you
by your service provider, then press OK.
4
5
At Car d No: enter the card number given to you by
your service provider, then press OK.
At Car d name: enter the card
name of your choice, then press
OK.
Activating Your Prepaid Card
Number
1
Press MENU 9 3.
2
3
Scroll to your prepaid card and press OK.
At Sel ect press OK.
You can also edit or erase your prepaid card number.
Making a Call
For complete information on making a call, see “Making a
1
Enter the number you want to call, then press and hold
SEND until you hear a tone.
2
At the tone, press OK and the card number you
saved is automatically sent to the network.
Ending a Call
For complete information on ending a call, see “Ending a
•
Press END.
62
PIN Calls
For complete information on making a call with PIN call on,
refer to “PIN Calls” on page 19.
Emergency 9 Dialing
For complete information on Emergency 9 Dialing, refer to
In-Call Menu
This is available only when you’re in a
call. To access it, give the MENU key
a short press. (A long press of the
MENU key gives you the normal
menu, as described in Section 6.)
The in-call menu works just like a normal menu. Move the
pointer and press OK to select an option. After you make
a choice, the phone automatically exits the in-call menu.
Mut e - This mutes the phone during a conversation.
The phone displays MUTED. To unmute the phone, select
the Mut e option again. The phone displays MUTE OFF.
Send DTMF - To send DTMF (Touch Tone) strings during
a call, first recall the stored string from memory. Then,
access the in-call menu with a short press of MENU.
Move the pointer to Send DTMF and press OK.
The phone sends the DTMF (Touch Tone) string.
Note: When you’re in the In-Call Menu, pressing any key
(0-9, *, #, CLR or END) exits the In-Call Menu. The phone
displays the digit pressed instead.
63
While the phone is alerting you of an incoming call (and
there are no other calls active or held), the In-Call menu is
not available until you answer the call. Similarly, when you
press SEND to initiate a call, until the call is connected,
there is no In-Call Menu.
Reminder Message
You can store a reminder message to appear the next
time you switch your phone on (it will appear once only).
To do this:
1
Enter your message (see “Entering Letters” on
2
Give MENU a quick press, then switch the phone off.
When you switch your phone on again, the message
displays.
To clear the message, press and hold CLR.
64
7. Data and Touch Tones
Data Mode
Data Mode can be used when your phone is connected,
via a suitable data card and modem, to a laptop or personal
computer. You may then use your computer to make and
receive calls, and to send and receive data messages
such as emails.
Follow these steps before using Data Mode:
•
Ensure your phone is switched on, and that the
battery has enough charge for the duration of your
data calls.
•
•
•
Ensure that you are receiving a strong signal
(see signal strength indicator on the display).
Ensure that your computer is switched on, and is
fitted with a data card.
Connect the data cable to the data card, and to your
phone.
To select Data Mode
Connect the data cable to your phone (DATA CARD
CONNECTED displays). When in a call, with the data cable
connected, the phone displays DATA CALL.
In a data call, the keys on the phone don’t work except for
END; when not in a call, all keys work. Also, the micro-
phone and earpiece don’t work in a data call.
Important! When you are in Data Mode, do not switch off
the phone. Do not move the phone, or use it in a moving
vehicle (data will be lost if you move from one cell to
another).
65
To de-select Data Mode
Disconnect the data cable (DATA CARD REMOVED
displays).
To operate your modem and data card
Refer to the documentation supplied with these items.
Sending Touch Tones
Your phone is a ‘Touch Tone’ phone. Touch Tones are the
sounds your phone makes when you press the keys.
Touch Tones can be used for many automated phone
services such as checking your bank balance and using
voice mailbox options.
Your phone refers to Touch Tones as ‘DTMF’ (Dual Tone
Multi Frequency).
Manually Sending Touch Tones
Pressing the keys during a call sends Touch Tones. To do
this:
1
Make a call in the usual way (e.g. to your bank's
computer phone number).
2
Manually enter the digits to be sent as Touch tones
(e.g., your bank account number and password).
Automatically Sending Touch Tones
For automatic sending of Touch Tones, you can store the
Touch Tone string within the same memory location as the
access phone number. Store a pause (p) or wait (w) char-
acter between the phone number and the Touch Tone string.
for details on storing pause and wait characters.
66
The following is an example of a number you could store
in your phone:
This number contains a phone number (18005551212), a
wait character, an access number (‘1234’), a wait charac-
ter, and a password (‘3434’) - 18005551212w1234w3434.
When you recall this number from memory and press
SEND, the phone:
•
•
Dials 18005551212 (the stored number), then:
‘Waits’ for you to press SEND again. When you do,
the phone sends the numbers 1234.
•
‘Waits’ for you to press SEND again, then sends the
numbers 3434.
The following example shows storing ‘pause’ characters
as well as ‘wait’ characters (Note that a ‘wait’ character
must still be included, as shown, to separate the phone
number from the following digits):
18005551212w1234p3434
When you recall this number from memory and press
SEND, the phone:
•
•
Dials 18005551212 (the stored number), then
‘Waits’ for you to press SEND again. When you do,
the phone sends the numbers 1234. It then:
•
Pauses for 2.5 seconds, then sends the numbers
3434.
Note: If the keypad tones have been set to Off, the Touch
Tones will still be sent, but you will not hear them.
Pressing MENU SEND sends a displayed number as a
Touch Tone.
To end the call, press END after the phone sends the
Touch Tones and has returned to the normal call mode.
67
Using the Flash Function
Your cellular system may offer a flash function service.
This system service lets you accept or make a second call
when you already have a call in progress (e.g. set up a
conference call), or send other information to the network,
such as credit card numbers.
Pressing SEND sends a displayed number to the network
as a flash, unless it is preceded by a ‘p’ or ‘w’. (In these
cases it is sent as a Touch Tone.)
After the phone number has been entered, you can add
extra information which is for ‘flash’ sending to the network.
Contact your service provider for further details.
68
8. Network Services
Availability of Network Services
The network services available will depend on the model
of your phone, the cellular system (AMPS or NAMPS) on
which it operates, and the services offered by your cellular
service provider.
To be able to use any of the network services, you will
need to subscribe to the particular service. The service
may not be available in all cellular service provider net-
works. Please contact your local cellular service provider
for further information.
Some services which may be available are listed below
and described briefly in this section:
•
•
•
•
•
Calling Line Identification
Call Waiting
Message Waiting
Voicemail
Digital Messaging Service, which includes Short Mes-
sage Service and Callback Number Service.
Calling Line Identification
When someone calls you, the phone
can display the caller’s phone number
or name (or a text message), with
CALLI NG flashing.
If the presentation of the caller’s iden-
tity is restricted by the network, or is withheld by the caller,
CALL- CALLER I D BLOCKED or CALL- I D NOT
AVAI LABLE may be displayed instead.
69
The caller’s name will be displayed if it is sent by the net-
work, or if the number sent matches the number and
name stored in your phone book.
Note: If the last seven digits of an incoming caller’s num-
ber match the last seven digits of a number stored in the
Phone Book, the phone displays the stored number/name
even if the area code or other dialing prefix is different.
The number will be stored in the Received Calls list or the
Missed Calls list, depending on whether you answer the
call or not.
Call Waiting
Call Waiting allows you to be informed of a incoming call
while you already have a call in progress.
When you have a call in progress and
a third party calls you, the phone can
display the caller’s phone number or
name (or a text message), with
CALLI NG flashing.
If the presentation of the caller’s identity is restricted by the
network, or is withheld by the caller, CALL- CALLER I D
BLOCKED or CALL- I D NOT AVAI LABLE may be
displayed instead.
To answer the incoming call:
1
When you get an incoming call alert (e.g., if you hear a
beep, or see the caller’s number or name, with
CALLI NG flashing), press SEND.
The second call will be answered, and the first call will
be put on hold (the caller’s number, if available, will be
stored in the Received Calls list). To then swap between
the two calls, press SEND. To end both calls, press END.
70
The caller’s name will be displayed if it is sent by the
network, or if the number sent matches the number and
name stored in your phone book.
Note: If the last seven digits of an incoming caller’s num-
ber match the last seven digits of a number stored in the
Phone Book, the phone displays the stored number/name
even if the area code or other dialing prefix is different.
If you don’t answer the incoming call, after approximately
20 seconds the call alert indications will stop and the
caller’s number (if available) will be added to the Missed
Calls list.
To clear the incoming call alert indications without
answering the call:
1
Press any key except SEND, END or PWR.
Message Waiting (Voicemail)
Message Waiting notifies you of unheard voice mail mes-
sages in your voice mailbox. The method of notification
varies from one network to another.
If you receive voicemail:
•
•
the voicemail indicator
lights,
NEW VOI CE MESSAGE or ‘n’ NEW VOI CE
MESSAGES may be displayed, indicating the number
(n) of unheard messages,
•
•
the index number may show the number of unheard
messages, and
a message-received tone may be heard, depending
on the new-message alert option you choose; refer to
71
For details on how to read your voicemail, refer to
To listen to your Voice Messages you can do any of the
following:
•
When NEW VOI CE MESSAGE or ‘n’ NEW VOI CE
MESSAGES is displayed, press SEND or OK.
•
Give the 1 key a long press to quick-dial your voice-
mail access number (if it is stored in phone book
location 1; see Note below).
•
Enter your voicemail access number, then press
SEND.
The service may offer voice guidance. You may need to
press keys on the phone keypad to access features.
Note: To be able to quick dial your voice mailbox with the
1 key:
1
Store your Voice Mailbox Access Number in the
Phone Book location 1 (see “Save Name & Number
2
Set the 1-Touch Dialing menu feature to On; for
You only need to do steps 1 and 2 once (unless, of course,
your voice mailbox access number changes).
72
Digital Message Service
(Nokia 252N only)
When you cannot answer calls the caller or switchboard
can send you a short message using the Digital Message
Service (DMS). The message can be a short text message,
a callback number, or a note to say you have voicemail.
When you receive a message:
•
•
the text message indicator
lights.
the note MESSAGE RECEI VED or ‘n’ MESSAGES
RECEI VED or a callback number may be displayed.
•
•
the message alert tone may be heard (to stop the
long tone, press any key except PWR or ! or ").
the message is stored automatically in the Messages
list.
To read a message when ‘MESSAGE RECEI VED’ or ‘n’
MESSAGES RECEI VED is displayed:
1
Press OK, or ! or ". To scroll other stored messages,
press ! or ". When at the bottom of the list, press "
to go up the list.
To erase a displayed message:
1
Press CLR.
2
When ERASE? is displayed, press OK.
To exit the Messages list:
Press CLR twice.
1
You can also read and erase messages, and set the
Message Alert Tone, using the Messages menu – for
details, refer to “Messages (Menu 7)” on page 52
(this menu item is available on the Nokia 252N only).
73
If the
indicator blinks the Messages List is full of read
or unread messages. If 20 messages are already stored,
when a new message arrives the oldest is erased
automatically.
If the same message is received twice, the most recent
message is stored, but the old message is erased from the
Messages List.
Short Message Service (SMS)
Callers can send you short pre-defined messages, such
as CALL HOME. Contact your local service provider for
information.
Callback Number Service
Callers can send you their callback numbers. Contact your
local service provider for information.
Note: If the number received matches a number and name
stored in the Phone Book the name will be displayed
instead.
To call the number received:
1
With the number (and message) displayed, press
SEND.
Some networks use this feature to send voicemail
notification.
74
9. Accessories
An extensive range of accessories is available for your
phone. You can select the accessories that best suit your
specific communication needs.
For availability, please check with your local dealer.
A few practical rules for accessory operation:
•
•
Keep the accessories out of small children's reach.
When you disconnect the power cord of any acces-
sory, grasp and pull the plug, not the cord.
•
•
Check regularly that all cellular phone equipment in a
vehicle is mounted and operating properly.
Installation of complex car equipment must be
completed by qualified personnel only.
WARNING!
Use only batteries, chargers and accessories ap-
proved by the phone manufacturer for use with this
particular phone model. The use of any other types
may invalidate any approval or warranty applying to
the phone, and may be dangerous.
75
Batteries
BMH-3
BMH-8
BML-8
The following batteries are available for your phone:
•
•
•
BMH-3 Extended NiMH 1150 mAh
BMH-8 Ultra Extended NiMH 1580 mAh
BML-8 Ultra Extended Vibra NiMH 1580 mAh
IMPORTANT!
Dispose of used batteries in accordance with any local
regulations.
For detailed battery information, including charging, talk,
and standby times, see “Battery Information”, beginning
76
ACP-7U Standard Travel Charger
Use this durable and economical
charger to charge both battery
options. Plug the charger into a wall
outlet and connect the connector to
the bottom of your phone. Check
the charging status on the phone
display. (See “Charging Times” on
Calls can be made during charging, but charging will stop
for the duration of the call and the battery bar scrolling
stops.
Note: If the battery is completely empty, you cannot use
the phone until it has enough charge to operate.
The Standard Travel Charger is available for different
voltage levels and can also be used with the CGH-10
Compact Desktop Charging Stand.
ACP-9U Rapid Travel Charger
The extremely light, functionally de-
signed Rapid Travel Charger charges
your phone battery quickly. (See
Plug the charger into a wall outlet and
connect the connector to the bottom of
your phone. Check the charging status
on the phone display. You can use your
phone while charging.
77
Operating within a voltage range of 100V-240V AC
(50Hz-60Hz), the Rapid Travel Charger is practically voltage-
independent in normal office and household use. Like the
Standard Travel Charger, the Rapid Travel Charger is
compatible with both battery options. The Rapid Travel
Charger can also be used with the Compact Desktop
Charging Stand CGH-10.
LCH-9 Rapid Cigarette Lighter Charger
The multivoltage Rapid Ciga-
rette Lighter Charger ensures
that your phone is always
ready for use wherever you
travel. The small charger's
functional design fits well with
most car lighters and interiors.
Charging times are the same as for the Rapid Travel
Calls can be made during charging.
A green light indicates that the Rapid Cigarette Lighter
Charger is ready to charge. Check the charging status on
the phone display. The input voltage is 12 or 24 V DC,
negative grounding.
The Rapid Cigarette Lighter Charger can be used with all
accessories available for your phone.
Avoid prolonged charging with the Rapid Cigarette Lighter
Charger when the car engine is not running. This may
cause the battery of your car to drain.
Note: In some cars the cigarette lighter plug is not
provided with power when the ignition is switched off.
Verify that the green LED light is lit.
78
CGH-10 Compact Desktop Charging
Stand
The Compact Desktop Charging Stand provides mounting
for both the phone and a spare battery. Plug the charger
into a wall outlet and connect the connector to the back of
the Compact Desktop Charging Stand. Place your phone
and/or a spare battery in the stand to begin battery
charging.
Note: You must fully insert the spare battery into the rear
slot of the charging stand in order for it to charge properly.
When the phone is charging, the charging status is indi-
cated on the phone’s display. When the spare battery is
charging, the green LED on the side of the stand lights.
(If the phone is in the charging stand while the spare bat-
tery is charging, the light periodically turns off while the
charger performs a “maintenance charge” on the phone.)
Compatible with both battery
options, the Compact Desktop
Charging Stand can be used
with the Standard Travel Charger
ACP-7U or the Rapid Travel
Charger ACP-9U.
The phone has the built-in intelligence to maintain the
battery, so there is no need for a discharge feature on the
stand.
79
BCH-10 Belt Clip
The belt clip lets you easily wear
your phone. To attach the belt clip
to the phone, first remove the
battery. Next slide the metal clip
onto the back of the phone, then
replace the battery. Attach the clip
holder to your belt and slide the
metal clip into the holder until it
locks.
To release the phone from the clip holder, press the
release button on the top of the holder.
HDXK-13 Headset Kit
The lightweight headset kit
provides you with handsfree oper-
ation of your phone. You can use it
in or out of a vehicle. The headset
kit is HATIS compatible for the
hearing impaired.
Simply fit the phone and headset
into the headset adapter.
80
10. Reference Information
Important Safety Information
Traffic Safety
Do not use a hand-held phone while driving a vehicle. If using a
hand-held phone, park the vehicle before conversing.
Always secure the phone in its holder; do not place the phone on
the passenger seat or where it can break loose in a collision or
sudden stop.
The use of an alert device to operate a vehicle's lights or horn on
public roads is not permitted. Remember, road safety always
comes first!
Operating Environment
Remember to follow any special regulations in force and always
switch off your phone whenever its use is forbidden, or when it may
cause interference or danger.
When connecting the phone or any accessory to another device,
read its user guide for detailed safety instructions. Do not connect
incompatible products.
As with other mobile radio transmitting equipment, users are ad-
vised that for the satisfactory operation of the equipment and for
the safety of personnel, it is recommended that the equipment
should only be used in the normal operating position. (Held to your
ear with the antenna pointing over your shoulder.)
Electronic Devices
Most modern electronic equipment is shielded from radio frequency
(RF) signals. However, certain electronic equipment may not be
shielded against the RF signals from your cellular phone.
Pacemakers
Pacemaker manufacturers recommend that a minimum separation
of 6 inches (20 cm.) be maintained between a handheld cellular
phone and a pacemaker to avoid potential interference with the
81
pacemaker. These recommendations are consistent with the
independent research by and recommendations of Wireless
Technology Research. Persons with pacemakers:
•
Should always keep the phone more than 6 inches (20 cm)
from their pacemaker when the phone is switched on;
•
•
Should not carry the phone in a breast pocket;
Should use the ear opposite the pacemaker to minimize the
potential for interference.
•
If you have any reason to suspect that interference is taking
place, switch off your phone immediately.
Hearing Aids
Some digital wireless phones may interfere with some hearing
aids. In the event of such interference, you may want to consult
your service provider.
Other Medical Devices
Operation of any radio transmitting equipment, including cellular
phones, may interfere with the functionality of inadequately pro-
tected medical devices. Consult a physician or the manufacturer of
the medical device to determine if they are adequately shielded
from external RF energy or if you have any questions. Switch off
your phone in health care facilities when any regulations posted in
these areas instruct you to do so. Hospitals or health care facilities
may be using equipment that could be sensitive to external RF
energy.
Vehicles
RF signals may affect improperly installed or inadequately shielded
electronic systems in motor vehicles (e.g. electronic fuel injection
systems, electronic anti-skid (anti-lock) braking systems, electronic
speed control systems, air bag systems). Check with the manufac-
turer or its representative regarding your vehicle. You should also
consult the manufacturer of any equipment that has been added
to your vehicle.
Posted Facilities
Switch your phone off in any facility where posted notices so require.
82
Potentially Explosive Atmospheres
Switch off your phone when in any area with a potentially explosive
atmosphere and obey all signs and instructions. Sparks in such
areas could cause an explosion or fire resulting in bodily injury or
even death.
Users are advised to switch off the phone while at a refueling point
(service station). Users are reminded of the need to observe re-
strictions on the use of radio equipment in fuel depots (fuel storage
and distribution areas), chemical plants or where blasting opera-
tions are in progress.
Areas with a potentially explosive atmosphere are often but not al-
ways clearly marked. They include below deck on boats; chemical
transfer or storage facilities; vehicles using liquefied petroleum gas
(such as propane or butane); areas where the air contains chemi-
cals or particles, such as grain, dust or metal powders; and any
other area where you would normally be advised to turn off your
vehicle engine.
Vehicles
Only qualified personnel should install the phone in a vehicle, or
service the phone. Faulty installation or service may be dangerous
and may invalidate any warranty which may apply to the unit.
Check regularly that all cellular phone equipment in your vehicle is
mounted and operating properly.
Do not store or carry flammable liquids, gases or explosive ma-
terials in the same compartment as a cellular phone or any of its
parts or accessories.
For vehicles equipped with an air bag, remember that an air bag
inflates with great force. Do not place objects, including both in-
stalled or portable wireless equipment, in the area over the air bag
or in the air bag deployment area. If in-vehicle wireless equipment
is improperly installed and the air bag inflates, serious injury could
result.
83
Switch off your phone before boarding an aircraft. The use of
cellular phones in an aircraft may be dangerous to the operation of
the aircraft, may disrupt the cellular network, and may be illegal.
Failure to observe these instructions may lead to the suspension or
denial of cellular telephone services to the offender, or legal action,
or both.
Emergency Calls
IMPORTANT!
This phone, like any cellular phone, operates by using radio sig-
nals, cellular and landline networks, as well as user- programmed
functions which cannot guarantee connection in all conditions.
Therefore, you should never rely solely upon any cellular phone for
essential communications (e.g. medical emergencies).
Remember, to make or receive any calls, the phone must be
switched on and in a service area with adequate cellular signal
strength. Emergency calls may not be possible on all cellular
phone networks or when certain network services and/or phone
features are in use. Check with local cellular service providers.
Making an Emergency Call
1
If the phone is not on, switch it on by pressing and
holding the PWR key.
2
3
Press and hold CLR to clear the display.
Enter the emergency number for your present loca-
tion (e.g., 911 or another official emergency number).
Emergency numbers vary by location.
4
Press SEND.
If certain features are in use (e.g., Keyguard), you may first need to
turn these off before you can make an emergency call. Consult this
document and your local service provider.
When making an emergency call, remember to give all the necessary
information as accurately as possible. Remember that your cellular
phone may be the only means of communication at the scene of
an accident. Do not end the call until given permission to do so.
84
Radio Frequency (RF) Signals
THIS MODEL PHONE MEETS THE GOVERNMENT'S
REQUIREMENTS FOR EXPOSURE TO RADIO WAVES.
Your wireless phone is a radio transmitter and receiver. It is designed
and manufactured not to exceed the emission limits for exposure to
radiofrequency (RF) energy set by the Federal Communications
Commission of the U.S. Government. These limits are part of
comprehensive guidelines and establish permitted levels of RF
energy for the general population. The guidelines are based on
standards that weredeveloped by independent scientific organizations
through periodic and thorough evaluation of scientific studies. The
standards include a substantial safety margin designed to assure
the safety of all persons, regardless of age and health.
The exposure standard for wireless mobile phones employs a unit
of measurement known as the Specific Absorption Rate, or SAR.
The SAR limit set by the FCC is 1.6W/kg.* Tests for SAR are
conducted using standard operating positions specified by the
FCC with the phone transmitting at its highest certified power level
in all tested frequency bands. Although the SAR is determined at
the highest certified power level, the actual SAR level of the phone
while operating can be well below the maximum value. This is
because the phone is designed to operate at multiple power levels
so as to use only the power required to reach the network. In
general, the closer you are to a wireless base station antenna, the
lower the power output.
Before a phone model is available for sale to the public, it must be
tested and certified to the FCC that it does not exceed the limit
established by the government-adopted requirement for safe
exposure. The tests are performed in positions and locations
(e.g., at the ear) as required by the FCC for each model. The highest
SAR value for this model phone when tested for use at the ear is
1.34 W/Kg. While there may be differences between the SAR
levels of various phones and at various positions, they all meet the
government requirement.
85
The FCC has granted an Equipment Authorization for this model
phone with all reported SAR levels evaluated as in compliance with
the FCC RF emission guidelines. SAR information on this model
phone is on file with the FCC and can be found under the Display
Grant section of http://www.fcc.gov/oet/fccid after searching on
FCC ID GML NHA-3.
Additional information on Specific Absorption Rates (SAR) can be
found on the Cellular Telecommunications Industry Association
(CTIA) web-site at http://www.wow-com.com.
________________________________________________
* In the United States and Canada, the SAR limit for mobile phones
used by the public is 1.6 watts/kg (W/kg) averaged over one gram
of tissue. The standard incorporates a substantial margin of safety
to give additional protection for the public and to account for any
variations in measurements.
86
Care and Maintenance
Your phone is a product of superior design and craftsman-
ship and should be treated with care. The suggestions
below will help you to fulfill any warranty obligations and
allow you to enjoy this product for many years. When
using your phone, battery, charger, OR any accessory:
•
•
•
•
Keep it and all its parts and accessories out of small children’s
reach.
Keep it dry. Precipitation, humidity and liquids contain
minerals that will corrode electronic circuits.
Do not use or store it in dusty, dirty areas as its moving parts
can be damaged.
Do not store it in hot areas. High temperatures can shorten
the life of electronic devices, damage batteries, and warp or
melt certain plastics.
•
Do not store it in cold areas. When the phone warms up
(to its normal operating temperature), moisture can form
inside the phone, which may damage the phone's electronic
circuit boards.
•
•
•
Do not attempt to open it. Non-expert handling of the device
may damage it.
Do not drop, knock or shake it. Rough handling can break
internal circuit boards.
Do not use harsh chemicals, cleaning solvents, or strong
detergents to clean it. Wipe it with a soft cloth slightly
dampened in a mild soap-and-water solution.
•
•
Do not paint it. Paint can clog the device’s moving parts and
prevent proper operation.
Use only the supplied or an approved replacement antenna.
Unauthorized antennas, modifications or attachments could
damage the phone and may violate regulations governing
radio devices.
•
If the phone, battery, charger, or any accessory is not working
properly, take it to your nearest qualified service facility.
The personnel there will assist you, and if necessary, arrange
for service.
87
11. Troubleshooting
Note: With a new, completely discharged battery, the
phone may take up to 45 minutes to show that charging is
in progress.
If the power does not come on or stay
on:
•
•
•
Make sure the battery is properly installed and
charged.
Be sure that the contacts on the battery and the
charging stand are clean.
Battery charge may be too low for operation. Check
the display and listen for the low battery warning
tones.
If the power comes on, but the phone
does not work:
•
If the phone displays NO SERVI CE, you’re out of the
cellular service area and you can’t make calls. You
also get this message if you’ve chosen Home Onl y
under Carrier Selection (in Menu 5 1), and you’ve left
your Home system.
•
•
Make sure that the antenna is properly installed and if
your phone has an extendable antenna, make sure
that the antenna is extended to its full length.
Check if there is an error message on the display after
switching the phone on. If so, contact your local
dealer.
88
12. Technical Information
Weight:
6.5 oz. with the BMH-3 or the
BMH-8 battery attached
Transmitting Power:
Operating Voltage:
600mW maximum
3.6V dc
12V dc for car kit
Frequency Band:
824.040 - 848.970MHz (TX)
869.040 - 893.970MHz (RX)
Number of Channels: 832
Phone Book Memory Up to 75*
Locations:
Memory Capacity
(per location):
32 numeric digits, and
30 letters
*Note: The maximum number of Phone Book entries
depends on how much information you store in each
location.
Nokia, Connecting People and the Original Accessories logos are
trademarks of Nokia Corporation and/or its affiliates.
The information contained in this User Guide was written for Nokia
phone NHA-3NA.
The right to make changes and improvements to any of the
products described in this guide without prior notice is reserved.
© 1999/2000 Nokia Mobile Phones. All rights reserved.
These commodities are authorized by the U.S. Government for
export only to Canada, Mexico, or the United States. They may not
be resold, diverted, transferred, or otherwise disposed of in any
other country, either in their original form or after being incorporated
through an intermediate process into other end-items, without the
written approval of the U.S. Department of State.
Part No. 9359756 Issue No. 2.
09/2000
Printed in Canada
89
13. NOKIA One-Year Limited
Warranty
Nokia Mobile Phones, Inc. (“NMP”) warrants that this cellular
phone (“Product”) is free from defects in material and workmanship
that result in Product failure during normal usage, according to the
following terms and conditions:
1. The limited warranty for the Product extends for ONE (1) year
beginning on the date of the purchase of the Product.
2. The limited warranty extends to the original purchaser of the
Product (“Consumer”) and is not assignable or transferable to any
subsequent purchaser/end-user.
3. The limited warranty extends only to Consumers who purchase
the Product in the United States.
4. During the limited warranty period, NMP will repair, or replace, at
NMP's option, any defective parts, or any parts that will not
properly operate for their intended use with new or factory rebuilt
replacement items if such repair or replacement is needed because
of product malfunction or failure during normal usage. No charge
will be made to the Consumer for any such parts. NMP will also
pay for the labor charges incurred by NMP in repairing or replacing
the defective parts. The limited warranty does not cover defects in
appearance, cosmetic, decorative or structural items, including
framing, and any non-operative parts. NMP's limit of liability under
the limited warranty shall be the actual cash value of the Product
at the time the Consumer returns the Product for repair, determined
by the price paid by the Consumer for the Product less a reasonable
amount for usage. NMP shall not be liable for any other losses or
damages. These remedies are the Consumer’s exclusive remedies
for breach of warranty.
5. Upon request from NMP, the Consumer must prove the date of
the original purchase of the Product by a dated bill of sale or dated
itemized receipt.
6. The Consumer shall bear the cost of shipping the Product to
NMP in Melbourne, Florida. NMP shall bear the cost of shipping
the Product back to the Consumer after the completion of service
under this limited warranty.
7. The Consumer shall have no coverage or benefits under this
limited warranty if any of the following conditions are applicable:
90
a) The Product has been subject to abnormal use, abnormal
conditions, improper storage, exposure to moisture or dampness,
unauthorized modifications, unauthorized connections, unauthorized
repair, misuse, neglect, abuse, accident, alteration, improper
installation, or other acts which are not the fault of NMP, including
damage caused by shipping.
b) The Product has been damaged from external causes such as
collision with an object, or from fire, flooding, sand, dirt, windstorm,
lightning, earthquake or damage from exposure to weather
conditions, an Act of God, or battery leakage, theft, blown fuse, or
improper use of any electrical source, or damage caused by the
connection to other products not recommended for
interconnection by NMP.
c) NMP was not advised by the Consumer in writing of the alleged
defect or malfunction of the Product within fourteen (14) days after
the expiration of the applicable limited warranty period.
d) The Product serial number plate or the accessory data code has
been removed, defaced or altered.
e) The defect or damage was caused by the defective function of
the cellular system or by inadequate signal reception by the
external antenna.
8. If a problem develops during the limited warranty period, the
Consumer shall take the following step-by-step procedure:
a) The Consumer shall return the Product to the place of purchase
for repair or replacement processing.
b) If “a” is not convenient because of distance (more than 50 miles)
or for other good cause, the Consumer shall ship the Product
prepaid and insured to:
Nokia Mobile Phones, Inc.
Attn: Repair Department
795 West Nasa Blvd.
Melbourne, FL. 32901
c) The Consumer shall include a return address, daytime phone
number and/or fax number, complete description of the problem,
proof of purchase and service agreement (if applicable). Expenses
related to removing the Product from an installation are not
covered under this limited warranty.
d) The Consumer will be billed for any parts or labor charges not
covered by this limited warranty. The Consumer will be responsible
for any expenses related to reinstallation of the Product.
91
e) NMP will repair or authorize the repair of the Product under the
limited warranty within 30 days after receipt of the Product by NMP
or an NMP authorized service center. If NMP cannot perform repair
covered under this limited warranty within 30 days, or after a
reasonable number of attempts to repair the same defect, NMP at
its option, will provide a replacement Product or refund the
purchase price of the Product less a reasonable amount for usage.
f) If the Product is returned to NMP during the limited warranty
period, but the problem with the Product is not covered under the
terms and conditions of this limited warranty, the Consumer will be
notified and given an estimate of the charges the Consumer must
pay to have the Product repaired, with all shipping charges billed
to the Consumer. If the estimate is refused, the Product will be
returned freight collect. If the Product is returned to NMP after the
expiration of the limited warranty period, NMP's normal service
policies shall apply and the Consumer will be responsible for all
shipping charges.
9. The Product consists of newly assembled equipment that may
contain used components that have been reprocessed to allow
machine compliance with Product performance and reliability
specifications.
10. ANY IMPLIED WARRANTY OF MERCHANTABILITY, OR
FITNESS FOR A PARTICULAR PURPOSE OR USE, SHALL BE
LIMITED TO THE DURATION OF THE FOREGOING LIMITED
WRITTEN WARRANTY. OTHERWISE, THE FOREGOING LIMITED
WARRANTY IS THE CONSUMER'S SOLE AND EXCLUSIVE
REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED. NMP SHALL NOT BE LIABLE FOR
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES,
INCLUDING BUT NOT LIMITED TO, LOSS OF ANTICIPATED
BENEFITS OR PROFITS, LOSS OF SAVINGS OR REVENUE,
PUNITIVE DAMAGES, LOSS OF USE OF THE PRODUCT OR
ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF
ANY SUBSTITUTE EQUIPMENT OR FACILITIES, DOWNTIME,
THE CLAIMS OF ANY THIRD PARTIES, INCLUDING CUSTOMERS,
AND INJURY TO PROPERTY, RESULTING FROM THE PURCHASE
OR USE OF THE PRODUCT OR ARISING FROM BREACH OF
THE WARRANTY, BREACH OF CONTRACT, NEGLIGENCE,
STRICT TORT, OR ANY OTHER LEGAL OR EQUITABLE THEORY,
EVEN IF NMP KNEW OF THE LIKELIHOOD OF SUCH DAMAGES.
NMP SHALL NOT BE LIABLE FOR DELAY IN RENDERING
SERVICE UNDER THE LIMITED WARRANTY, OR LOSS OF USE
DURING THE PERIOD THAT THE PRODUCT IS BEING REPAIRED.
92
11. Some states do not allow limitation of how long an implied
warranty lasts, so the above one-year warranty limitation may not
apply to you (the Consumer). Some states do not allow the
exclusion or limitation of incidental and consequential damages, so
certain of the above limitations or exclusions may not apply to you
(the Consumer). This limited warranty gives the Consumer specific
legal rights and the Consumer may also have other rights which
vary from state to state.
12. NMP neither assumes nor authorizes any authorized service
center or any other person or entity to assume for it any other
obligation or liability beyond that which is expressly provided for in
this limited warranty including the provider or seller of any extended
warranty or service agreement.
13. This is the entire warranty between NMP and the Consumer,
and supersedes all prior and contemporaneous agreements or
understandings, oral or written, and all communications relating to
the Product, and no representation, promise or condition not
contained herein shall modify these terms.
14. This limited warranty allocates the risk of failure of the Product
between the Consumer and NMP. The allocation is recognized by
the Consumer and is reflected in the purchase price of the Product.
15. Any action or lawsuit for breach of warranty must be
commenced within eighteen (18) months following delivery of the
Product.
16. Questions concerning this limited warranty may be directed to:
Nokia Customer Care Center, USA
Nokia Mobile Phones, Inc.
7725 Woodland Center Boulevard, Suite #150
Tampa, FL 33614
Telephone: 1-888-NOKIA2U (1-888-665-4228)
Fax: (1) 813-249-9619
TTY Users: 1-800-24NOKIA (1-800-246-6542)
17. The limited warranty period for NMP supplied attachments and
accessories is specifically defined within their own warranty cards
and packaging.
© Nokia is a registered trademark of Nokia Corporation.
93
calls lists
call log menu 33
erasing 35
carrier selection 45
chargers 7, 77-79
CLR key 13
14. Index
Symbols
’+’ (link) character 24
’p’ (pause) character 24, 66
’w’ (wait) character 24, 66
to clear display 22
to edit name or number 32
to end PIN Call attempts 20
to exit Menu 28
Numerics
1-touch dialing 16, 39
9 key. See also emergency 9
dialing 16
when entering letters 22
A
D
AB indicator 3
ABC indicator 3
ABC key 22
data mode 65
debit 30, 55
checksum 56
timetank 55
dialed calls list 33
digital message service 73
display 3
DTMF 19, 63, 66
See also touch tones. 66
accessories 75
allowed calls 48
alpha mode 22
automatic answer 42
automatic redial 42
B
battery 5-10
E
charge indicator 3
charging times 7
discharging 8
discharging, deep 9
talk and standby times 8
BATTERY LOW 9
emergency 9 dialing 16, 40
and Keyguard 18
emergency calls 16, 84
F
flash function 68
C
H
call back number service 74
call log 33
house indicator 3
I
CALL NOT ALLOWED 14
call timers 36
in-call menu 63
call waiting 70
caller ID 15
calling card 49
calls 18
entering info about 49
calling line identification 15, 69
calls
answering 14
automatic answering 42
ending 14
K
Keyguard 17
keypad tones 38
L
language 41
letters and punctuation 23
lights 39
lock code
change 43
lock phone 51, 52
making 13
94
add money 60
card 61
check balance 61
M
memory locations
75 24, 52
indicator 3
linking 24
maximum 22
notepad 26
menu
in-call 63
summary 30
using 28
using during a call 29
messages
alert tone 54
erasing 54
menu 52
reading 53
text 20
R
received calls list 34
RECHARGE BATTERY 9
redial
automatic 42
last 10 dialed calls. See also
dialed calls 15
last number 15
reminder message 64
REPLACE? 24, 32
restore factory settings 44
ringing
options 37
tone 38
volume 37
voice 20
missed calls list 34
ROAMI NG 47
S
N
safety guidelines 1, 81
security code 44
change 44
network selection. See carrier
selection. 12
network services 69
NO SERVI CE 13, 47, 88
NON- PREF. 47
short message service 74
short text message
indicator 3
signal strength 4
silent service 14, 37
speed dialing 16
switching on or off 12
SYSTEM BUSY 42
notepad memory 26
P
Phone Book
status of 33
phone book 22-27
erasing entries from 32
finding entries in 26
saving entries in 24
using Menu 1 31
phone indicator 3
phone number 41
PIN calls 19
T
touch tones 19, 63, 66
V
voicemail
indicator 3
volume
earpiece 15
ringing 37
PREFERRED 47
preferred network 3, 46
prepaid 59
access numbers 60
95
Para obtener un manual del usuario en español favor
de llamar o enviar un fax al teléfono 1-888-NOKIA2U
(1-888-665-4228), fax 813-249-9619.
96
|