Hardware Maintenance Manual
Types 8084, 8085, 8126, 8147, 8148, 8149
Types 8174, 8175, 8176, 8177, 8178, 8179
Hardware Maintenance Manual
Types 8084, 8085, 8126, 8147, 8148, 8149
Types 8174, 8175, 8176, 8177, 8178, 8179
Note: Before using this information and the product it supports, be sure to read the
information under “Notices,” on page 219.
Sixth Edition (August 2005)
© Copyright Lenovo 2005.
Portions © Copyright International Business Machines Corporation 2005.
All rights reserved.
U.S. GOVERNMENT USERS – RESTRICTED RIGHTS: Our products and/or services are provided with
RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to the GSA ADP Schedule
contract with Lenovo Group Limited, if any, or the standard terms of this commercial license, or if the agency is
unable to accept this Program under these terms, then we provide this Program under the provisions set forth in
Commercial Computer Software–Restricted Rights at FAR 52.227-19, when applicable, or under Rights in
Data-General, FAR 52.227.14 (Alternate III).
Contents
© Lenovo 2005. Portions © IBM Corp. 2005.
iii
iv Hardware Maintenance Manual
Chapter 1. About this manual
This manual contains service and reference information for ThinkCentre®
computers listed on the cover. It is intended only for trained servicers who are
familiar with Lenovo computer products.
Before servicing a Lenovo product, be sure to read the Safety Information. See
The Symptom-to-FRU Index and Additional Service Information chapters are not
specific to any machine type and are applicable to all ThinkCentre computers.
This manual includes a complete FRU part number listing for each machine type
and model listed on the cover. If you have internet access, FRU part numbers are
also available at:
http:/www.lenovo.com/think/support
Important Safety Information
Be sure to read all caution and danger statements in this book before performing
any of the instructions.
Veuillez lire toutes les consignes de type DANGER et ATTENTION du présent
document avant d’exécuter les instructions.
Lesen Sie unbedingt alle Hinweise vom Typ ″ACHTUNG″ oder ″VORSICHT″ in
dieser Dokumentation, bevor Sie irgendwelche Vorgänge durchführen
Leggere le istruzioni introdotte da ATTENZIONE e PERICOLO presenti nel
manuale prima di eseguire una qualsiasi delle istruzioni
Certifique-se de ler todas as instruções de cuidado e perigo neste manual antes de
executar qualquer uma das instruções
Es importante que lea todas las declaraciones de precaución y de peligro de este
manual antes de seguir las instrucciones.
© Lenovo 2005. Portions © IBM Corp. 2005.
1
Strategy for replacing FRUs for CTO, CMV, and GAV products
Product definition
Dynamic Configure To Order (CTO)
This provides the ability for a customer to configure a Lenovo solution
from an eSite, and have this configuration sent to fulfillment, where it is
built and shipped directly to the customer. The machine label, PC
Entitlement Warehouse (PEW), eSupport, and the HMM will include these
products as the 4-digit machine type (MT) and 3-digit model, where model
= ’CTO’ (Example: 8129-CTO).
Custom Model Variant (CMV)
This is a unique configuration that has been negotiated between Lenovo
and the customer. A unique 4-digit MT and 3-digit model is provided to
the customer to place orders (Example: 8129-W15). A CMV is a special bid
offering. Therefore, it is NOT generally announced.
v The machine type model (MTM) portion of the machine label is the
4-digit MT and 3-digit model, where model = ’CTO’ (Example:
8129-CTO). The PRODUCT ID portion of the machine label is the 4-digit
MT and 3-digit CMV model (Example: 8129-W15).
v The PEW record is the 4-digit MT and 3-digit model, where model =
’CTO’ (Example: 8129-CTO).
v eSupport will show both the CTO and CMV machine type models
(Example: 8129-CTO and 8129-W15 will be found on the eSupport site.)
v The HMM will have the 4-digit MT and 3-digit CTO model only
(Example: 8129-CTO). Again, CMVs are custom models and are not
found in the HMM.
General Announce Variant (GAV)
This is a standard model (fixed configuration). GAVs are announced and
offered to all customers. The MTM portion of the machine label is a 4-digit
MT and 3-digit model, where model = a “fixed model number”, not ’CTO’
(Example: 8129-F1U). Also, PEW, eSupport, and the HMM will list these
products under the same fixed model number.
FRU Identification for CTO, CMV, and GAV products
There are three information resources to identify which FRUs are used to support
CTO, CMV, and GAV products. These sources are PEW, eSupport, and the HMM.
Using PEW
v PEW is the primary source for identifying FRU part numbers and FRU
descriptions for the key commodities for CTO, CMV and GAV products at a MT
- serial number level. An example of key commodities are hard disk drives,
system boards, microprocessors, Liquid Crystal Displays (LCDs), and memory.
v Remember, All CTO and CMV products are loaded in PEW under the 4-digit
MT and 3-digit model, where model = ’CTO’ (Example: 8129-CTO). GAVs are
loaded in PEW under the 4-digit MT and 3-digit model, where model = a “fixed
model number”, not ’CTO’ (Example: 8129-F1U).
v PEW can be accessed as follows:
1. Point your browser to http://w3-3.ibm.com/pc/entitle.
2. Under PEW Home, click Machine Lookup.
3. Under Machine Lookup, click Warranty Information.
2
Hardware Maintenance Manual
4. Under Warranty Information, type the MT and Serial number and click
Submit.
The list of key commodities is returned in the PEW record under Component
Information.
v Business Partners using Eclaim will access PEW when performing Entitlement
Lookup. Business Partners will enter Loc ID, MT and Serial, and the key
commodities will be returned in the Eclaim record under System Details.
v Authorized Lenovo Business Partners can access Eclaim at the following Web
site:
http://wca.eclaim.com
Using eSupport
For Key Commodities (Examples - hard disk drive, system board,
microprocessor, LCD, and memory)
v eSupport can be used to view the list of key commodities built in a particular
machine serial (this is the same record found in PEW).
v eSupport can be accessed at the following Web site:
http://www.lenovo.com/think/support
v To view the key commodities:
1. Click Parts information.
2. Under Parts information, click Parts lookup.
3. Under Parts lookup, type the model type and serial number; then click
Continue.
The key commodities are returned in the eSupport record under Parts
shipped with your system.
For the remaining FRUs (the complete list of FRUs at the MT Model level)
v eSupport can be used to view the complete list of FRUs for a machine type and
model.
v To view the complete list of FRUs for a machine type:
1. Point your browser to http://www.lenovo.com/think/support.
2. Type the machine type (Example: 8129) in the Use Quick Path field; then
click Go.
3. Under Browse by product, click Continue.
4. Under Important information, click Parts information.
5. In the Refine results field, select Service parts; then click the entry for your
machine type.
The list of service parts by description, with applicable machine type model
and FRU part number is displayed.
Using the HMM
v Use the HMM as a back-up to PEW and eSupport to view the complete list of
FRU part numbers at the MT Model level.
Important information about replacing RoHS compliant FRUs
RoHS, The Restriction of Hazardous Substances in Electrical and Electronic
Equipment Directive (2002/95/EC) is a European Union legal requirement
affecting the global electronics industry. RoHS requirements must be
implemented on Lenovo products placed on the market after June 2006. Products
on the market before June 2006 are not required to have RoHS compliant parts.
Chapter 1. About this manual
3
So, if the parts are not compliant originally, replacement parts can also be
noncompliant, but in all cases, if the parts are compliant, the replacement parts
must also be compliant.
Lenovo plans to transition to RoHS compliance well before the implementation
date and expects its suppliers to be ready to support Lenovo’s requirements and
schedule. Products sold in 2005, will contain some RoHS compliant FRUs. The
following statement pertains to these products and any product Lenovo produces
containing RoHS compliant parts.
RoHS compliant ThinkCentre parts have unique FRU part numbers. Before or after
June, 2006, failed RoHS compliant parts must always be replaced using RoHS
compliant FRUs, so only the FRUs identified as compliant in the system HMM or
direct substitutions for those FRUs can be used.
Products marketed before June 2006
Products marketed after June 2006
Current or original
part
Replacement FRU
Current or original
part
Replacement FRU
Non-RoHS
Non-RoHS
Non-RoHS
RoHS
Can be Non-RoHS
Can be RoHS
Must be RoHS
Must be RoHS
Can sub to RoHS
Must be RoHS
Note: A direct substitution is a part with a different FRU part number that is
automatically shipped by the distribution center at the time of order.
Related Web URLs are:
v Lenovo information for Suppliers website:
http://www-03.ibm.com/procurement/proweb.nsf/ContentDocsByTitle/
United+States~Information+for+suppliers
v RoHS Directive:
http://europa.eu.int/eur-lex/pri/en/oj/dat/2003/l_037/
l_03720030213en00190023.pdf
v California Senate Bills 20, 50:
http://www.ciwmb.ca.gov/HHW/Events/AnnualConf/2004/
presentation/MPaparian.pdf
4
Hardware Maintenance Manual
Chapter 2. Safety information
This chapter contains the safety information that you need to be familiar with
before servicing a computer.
General safety
Follow these rules to ensure general safety:
v Observe good housekeeping in the area of the machines during and after
maintenance.
v When lifting any heavy object:
1. Ensure you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to
lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes
the strain from the muscles in your back. Do not attempt to lift any objects that
weigh more than 16 kg (35 lb) or objects that you think are too heavy for you.
v Do not perform any action that causes hazards to the customer, or that makes
the equipment unsafe.
v Before you start the machine, ensure that other service representatives and the
customer’s personnel are not in a hazardous position.
v Place removed covers and other parts in a safe place, away from all personnel,
while you are servicing the machine.
v Keep your tool case away from walk areas so that other people will not trip over
it.
v Do not wear loose clothing that can be trapped in the moving parts of a
machine. Ensure that your sleeves are fastened or rolled up above your elbows.
If your hair is long, fasten it.
v Insert the ends of your necktie or scarf inside clothing or fasten it with a
nonconductive clip, approximately 8 centimeters (3 inches) from the end.
v Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your
clothing.
Remember: Metal objects are good electrical conductors.
v Wear safety glasses when you are: hammering, drilling soldering, cutting wire,
attaching springs, using solvents, or working in any other conditions that might
be hazardous to your eyes.
v After service, reinstall all safety shields, guards, labels, and ground wires.
Replace any safety device that is worn or defective.
v Reinstall all covers correctly before returning the machine to the customer.
Electrical safety
© Lenovo 2005. Portions © IBM Corp. 2005.
5
CAUTION:
Electrical current from power, telephone, and communication cables can be
hazardous. To avoid personal injury or equipment damage, disconnect the
attached power cords, telecommunication systems, networks, and modems before
you open the server/workstation covers, unless instructed otherwise in the
installation and configuration procedures.
Observe the following rules when working on electrical equipment.
Important: Use only approved tools and test equipment. Some hand tools have
handles covered with a soft material that does not insulate you when
working with live electrical currents.
Many customers have, near their equipment, rubber floor mats that
contain small conductive fibers to decrease electrostatic discharges. Do
not use this type of mat to protect yourself from electrical shock.
v Find the room emergency power-off (EPO) switch, disconnecting switch, or
electrical outlet. If an electrical accident occurs, you can then operate the switch
or unplug the power cord quickly.
v Do not work alone under hazardous conditions or near equipment that has
hazardous voltages.
v Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
v Before you start to work on the machine, unplug the power cord. If you cannot
unplug it, ask the customer to power-off the wall box that supplies power to the
machine and to lock the wall box in the off position.
v If you need to work on a machine that has exposed electrical circuits, observe
the following precautions:
– Ensure that another person, familiar with the power-off controls, is near you.
Remember: Another person must be there to switch off the power, if
necessary.
– Use only one hand when working with powered-on electrical equipment;
keep the other hand in your pocket or behind your back.
Remember: There must be a complete circuit to cause electrical shock. By
observing the above rule, you may prevent a current from passing through
your body.
– When using testers, set the controls correctly and use the approved probe
leads and accessories for that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you
from grounds such as metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages;
these instructions are in the safety sections of maintenance information. Use
extreme care when measuring high voltages.
v Regularly inspect and maintain your electrical hand tools for safe operational
condition.
v Do not use worn or broken tools and testers.
v Never assume that power has been disconnected from a circuit. First, check that it
has been powered-off.
6
Hardware Maintenance Manual
v Always look carefully for possible hazards in your work area. Examples of these
hazards are moist floors, nongrounded power extension cables, power surges,
and missing safety grounds.
v Do not touch live electrical circuits with the reflective surface of a plastic dental
mirror. The surface is conductive; such touching can cause personal injury and
machine damage.
v Do not service the following parts with the power on when they are removed
from their normal operating places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
and similar units. (This practice ensures correct grounding of the units.)
v If an electrical accident occurs:
– Use caution; do not become a victim yourself.
– Switch off power.
– Send another person to get medical aid.
Safety inspection guide
The intent of this inspection guide is to assist you in identifying potentially unsafe
conditions on these products. Each machine, as it was designed and built, had
required safety items installed to protect users and service personnel from injury.
This guide addresses only those items. However, good judgment should be used to
identify potential safety hazards due to attachment of features or options not
covered by this inspection guide.
If any unsafe conditions are present, you must determine how serious the apparent
hazard could be and whether you can continue without first correcting the
problem.
Consider these conditions and the safety hazards they present:
v Electrical hazards, especially primary power (primary voltage on the frame can
cause serious or fatal electrical shock).
v Explosive hazards, such as a damaged CRT face or bulging capacitor
v Mechanical hazards, such as loose or missing hardware
The guide consists of a series of steps presented in a checklist. Begin the checks
with the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power-off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure
third-wire ground continuity for 0.1 ohm or less between the external
ground pin and frame ground.
b. The power cord should be the appropriate type as specified in the parts
listings.
c. Insulation must not be frayed or worn.
4. Remove the cover.
Chapter 2. Safety information
7
5. Check for any obvious alterations. Use good judgment as to the safety of any
alterations.
6. Check inside the unit for any obvious unsafe conditions, such as metal filings,
contamination, water or other liquids, or signs of fire or smoke damage.
7. Check for worn, frayed, or pinched cables.
8. Check that the power-supply cover fasteners (screws or rivets) have not been
removed or tampered with.
Handling electrostatic discharge-sensitive devices
Any computer part containing transistors or integrated circuits (ICs) should be
considered sensitive to electrostatic discharge (ESD). ESD damage can occur when
there is a difference in charge between objects. Protect against ESD damage by
equalizing the charge so that the machine, the part, the work mat, and the person
handling the part are all at the same charge.
Notes:
1. Use product-specific ESD procedures when they exceed the requirements noted
here.
2. Make sure that the ESD protective devices you use have been certified (ISO
9000) as fully effective.
When handling ESD-sensitive parts:
v Keep the parts in protective packages until they are inserted into the product.
v Avoid contact with other people.
v Wear a grounded wrist strap against your skin to eliminate static on your body.
v Prevent the part from touching your clothing. Most clothing is insulative and
retains a charge even when you are wearing a wrist strap.
v Use the black side of a grounded work mat to provide a static-free work surface.
The mat is especially useful when handling ESD-sensitive devices.
v Select a grounding system, such as those listed below, to provide protection that
meets the specific service requirement.
Note: The use of a grounding system is desirable but not required to protect
against ESD damage.
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire
ground.
– Use an ESD common ground or reference point when working on a
double-insulated or battery-operated system. You can use coax or
connector-outside shells on these systems.
– Use the round ground-prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct
system function. Proper grounding of the electrical outlet can be verified by a
certified electrician.
8
Hardware Maintenance Manual
Safety notices (multi-lingual translations)
The caution and danger safety notices in this section are provided in the following
languages:
v English
v Arabic
v Brazilian/Portuguese
v Chinese (simplified)
v Chinese (traditional)
v French
v German
v Hebrew
v Italian
v Korean
v Spanish
DANGER
Electrical current from power, telephone and communication cables is hazardous.
To avoid a shock hazard:
v Do not connect or disconnect any cables or perform installation, maintenance,
or reconfiguration of this product during an electrical storm.
v Connect all power cords to a properly wired and grounded electrical outlet.
v Connect to properly wired outlets any equipment that will be attached to this
product.
v When possible, use one hand only to connect or disconnect signal cables.
v Never turn on any equipment when there is evidence of fire, water, or
structural damage.
v Disconnect the attached power cords, telecommunications systems, networks,
and modems before you open the device covers, unless instructed otherwise
in the installation and configuration procedures.
v Connect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached devices.
To Connect
To Disconnect
1. Turn everything OFF.
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach power cords to outlet.
5. Turn device ON.
2. First, remove power cords from outlet.
3. Remove signal cables from connectors.
4. Remove all cables from devices.
Chapter 2. Safety information
9
CAUTION:
When replacing the lithium battery, use only Part Number 33F8354 or an
equivalent type battery recommended by the manufacturer. If your system has a
module containing a lithium battery, replace it only with the same module type
made by the same manufacturer. The battery contains lithium and can explode if
not properly used, handled, or disposed of.
Do not:
v Throw or immerse into water
v Heat to more than 100°C (212°F)
v Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
CAUTION:
When laser products (such as CD-ROMs, DVD-ROM drives, fiber optic devices,
or transmitters) are installed, note the following:
v Do not remove the covers. Removing the covers of the laser product could
result in exposure to hazardous laser radiation. There are no serviceable parts
inside the device.
v Use of controls or adjustments or performance of procedures other than those
specified herein might result in hazardous radiation exposure.
DANGER: Some laser products contain an embedded Class 3A or Class 3B laser
diode. Note the following:
Laser radiation when open. Do not stare into the beam, do not view
directly with optical instruments, and avoid direct exposure to the
beam.
≥18 kg (37 lbs)
≥32 kg (70.5 lbs)
≥55 kg (121.2 lbs)
CAUTION:
Use safe practices when lifting.
10 Hardware Maintenance Manual
CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current from
the device, ensure that all power cords are disconnected from the power source.
2
1
CAUTION:
Do not place any object weighing more than 82 kg (180 lbs.) on top of
rack-mounted devices.
Chapter 2. Safety information 11
12 Hardware Maintenance Manual
Chapter 2. Safety information 13
≥18 kg (37 lbs)
≥32 kg (70.5 lbs)
≥55 kg (121.2 lbs)
2
1
14 Hardware Maintenance Manual
PERIGO
A corrente elétrica proveniente de cabos de alimentação, de telefone e de
comunicações é perigosa.
Para evitar risco de choque elétrico:
v Não conecte nem desconecte nenhum cabo ou execute instalação, manutenção
ou reconfiguração deste produto durante uma tempestade com raios.
v Conecte todos os cabos de alimentação a tomadas elétricas corretamente
instaladas e aterradas.
v Todo equipamento que for conectado a este produto deve ser conectado a
tomadas corretamente instaladas.
v Quando possível, utilize apenas uma das mãos para conectar ou desconectar
cabos de sinal.
v Nunca ligue nenhum equipamento quando houver evidência de fogo, água ou
danos estruturais.
v Antes de abrir tampas de dispositivos, desconecte cabos de alimentação,
sistemas de telecomunicação, redes e modems conectados, a menos que
especificado de maneira diferente nos procedimentos de instalação e
configuração.
v Conecte e desconecte os cabos conforme descrito na tabela apresentada a seguir
ao instalar, mover ou abrir tampas deste produto ou de dispositivos conectados.
Para Conectar:
Para Desconectar:
1. DESLIGUE Tudo.
1. DESLIGUE Tudo.
2. Primeiramente, conecte todos os cabos
2. Primeiramente, remova os cabos de
aos dispositivos.
alimentação das tomadas.
3. Conecte os cabos de sinal aos
3. Remova os cabos de sinal dos conectores.
conectores.
4. Remova todos os cabos dos dispositivos.
4. Conecte os cabos de alimentação às
tomadas.
5. LIGUE os dispositivos.
Chapter 2. Safety information 15
CUIDADO:
Ao substituir a bateria de lítio, utilize apenas uma bateria com Número de Peça
33F8354 ou um tipo de bateria equivalente recomendado pelo Se o seu sistema
possui um módulo com uma bateria de lítio, substitua-o apenas por um módulo
do mesmo tipo e do mesmo fabricante. A bateria contém lítio e pode explodir se
não for utilizada, manuseada ou descartada de maneira correta.
Não:
v Jogue ou coloque na água
v Aqueça a mais de 100°C (212°F)
v Conserte nem desmonte
Descarte a bateria conforme requerido pelas leis ou regulamentos locais.
PRECAUCIÓN:
Quando produtos a laser (como unidades de CD-ROMs, unidades de DVD-ROM,
dispositivos de fibra ótica ou transmissores) estiverem instalados, observe o
seguinte:
v Não remova as tampas. A remoção das tampas de um produto a laser pode
resultar em exposição prejudicial à radiação de laser. Não existem peças que
podem ser consertadas no interior do dispositivo.
v A utilização de controles ou ajustes ou a execução de procedimentos diferentes
dos especificados aqui pode resultar em exposição prejudicial à radiação.
PERIGO
Alguns produtos a laser contêm diodo de laser integrado da Classe 3A ou da
Classe 3B. Observe o seguinte:
Radiação a laser quando aberto. Não olhe diretamente para o feixe a olho nu ou
com instrumentos ópticos e evite exposição direta ao feixe.
≥18 kg (37 lbs)
≥32 kg (70.5 lbs)
≥55 kg (121.2 lbs)
CUIDADO:
Utilize procedimentos de segurança para levantar equipamentos.
16 Hardware Maintenance Manual
CUIDADO:
O botão de controle de alimentação do dispositivo e o botão para ligar/desligar da
fonte de alimentação não desligam a corrente elétrica fornecida ao dispositivo. O
dispositivo também pode ter mais de um cabo de alimentação. Para remover toda
a corrente elétrica do dispositivo, assegure que todos os cabos de alimentação
estejam desconectados da fonte de alimentação.
2
1
CUIDADO:
Não coloque nenhum objeto com mais de 82 kg (180 lbs.) sobre dispositivos
montados em rack.
Chapter 2. Safety information 17
18 Hardware Maintenance Manual
2
1
Chapter 2. Safety information 19
20 Hardware Maintenance Manual
Chapter 2. Safety information 21
2
1
22 Hardware Maintenance Manual
DANGER
Le courant électrique provenant de l’alimentation, du téléphone et des câbles de
transmission peut présenter un danger.
Pour éviter tout risque de choc électrique :
v Ne manipulez aucun câble et n’effectuez aucune opération d’installation,
d’entretien ou de reconfiguration de ce produit au cours d’un orage.
v Branchez tous les cordons d’alimentation sur un socle de prise de courant
correctement câblé et mis à la terre.
v Branchez sur des socles de prise de courant correctement câblés tout équipement
connecté à ce produit.
v Lorsque cela est possible, n’utilisez qu’une seule main pour connecter ou
déconnecter les câbles d’interface.
v Ne mettez jamais un équipement sous tension en cas d’incendie ou d’inondation,
ou en présence de dommages matériels.
v Avant de retirer les carters de l’unité, mettez celle-ci hors tension et déconnectez
ses cordons d’alimentation, ainsi que les câbles qui la relient aux réseaux, aux
systèmes de télécommunication et aux modems (sauf instruction contraire
mentionnée dans les procédures d’installation et de configuration).
v Lorsque vous installez, que vous déplacez, ou que vous manipulez le présent
produit ou des périphériques qui lui sont raccordés, reportez-vous aux
instructions ci-dessous pour connecter et déconnecter les différents cordons.
Connexion
Déconnexion
1. Mettez les unités HORS TENSION.
1. Mettez les unités HORS TENSION.
2. Commencez par brancher tous les
2. Débranchez les cordons d’alimentation
cordons sur les unités.
des prises.
3. Branchez les câbles d’interface sur des
3. Débranchez les câbles d’interface des
connecteurs.
connecteurs.
4. Branchez les cordons d’alimentation sur 4. Débranchez tous les câbles des unités.
des prises.
5. Mettez les unités SOUS TENSION.
Chapter 2. Safety information 23
ATTENTION:
Remplacer la pile au lithium usagée par une pile de référence identique
exclusivement, (référence 33F8354), ou suivre les instructions du fabricant qui en
définit les équivalences. Si votre système est doté d’un module contenant une
pile au lithium, vous devez le remplacer uniquement par un module identique,
produit par le même fabricant. La pile contient du lithium et peut exploser en
cas de mauvaise utilisation, de mauvaise manipulation ou de mise au rebut
inappropriée.
Ne pas :
v la jeter à l’eau,
v l’exposer à des températures supérieures à 100°C,
v chercher à la réparer ou à la démonter.
Ne pas mettre la pile à la poubelle. Pour la mise au rebut, se reporter à la
réglementation en vigueur.
ATTENTION:
Si des produits à laser (tels que des unités de CD-ROM, de DVD-ROM, des
unités à fibres optiques, ou des émetteurs) sont installés, prenez connaissance
des informations suivantes :
v Ne retirez pas le carter. En ouvrant l’unité de CD-ROM ou de DVD-ROM,
vous vous exposez au rayonnement dangereux du laser. Aucune pièce de
l’unité n’est réparable.
v Pour éviter tout risque d’exposition au rayon laser, respectez les consignes de
réglage et d’utilisation des commandes, ainsi que les procédures décrites dans
le présent manuel.
DANGER
Certains produits à laser contiennent une diode à laser intégrée de classe 3A ou
3B. Prenez connaissance des informations suivantes:
Rayonnement laser lorsque le carter est ouvert. Evitez toute expositiondirecte au
rayon laser. Evitez de regarder fixement le faisceau ou del’observer à l’aide
d’instruments optiques.
24 Hardware Maintenance Manual
≥18 kg (37 lbs)
≥32 kg (70.5 lbs)
≥55 kg (121.2 lbs)
ATTENTION:
Soulevez la machine avec précaution.
ATTENTION:
L’interrupteur de contrôle d’alimentation de l’unité et l’interrupteur dubloc
d’alimentation ne coupent pas le courant électrique alimentantl’unité. En outre,
le système peut être équipé de plusieurs cordonsd’alimentation. Pour mettre
l’unité hors tension, vous devez déconnectertous les cordons de la source
d’alimentation.
2
1
ATTENTION:
Ne placez pas d’objet supérieur à 82 kg sur une unité montée en armoire.
Chapter 2. Safety information 25
VORSICHT
An Netz-, Telefon- und Datenleitungen können gefährliche Spannungen anliegen.
Aus Sicherheitsgründen:
v Bei Gewitter an diesem Gerät keine Kabel anschließen oder lösen. Ferner
keine Installations-, Wartungs- oder Rekonfigurationsarbeiten durchführen.
v Gerät nur an eine Schutzkontaktsteckdose mit ordnungsgemäß geerdetem
Schutzkontakt anschließen.
v Alle angeschlossenen Geräte ebenfalls an Schutzkontaktsteckdosen mit
ordnungsgemäß geerdetem Schutzkontakt anschließen.
v Die Signalkabel nach Möglichkeit einhändig anschließen oder lösen, um
einen Stromschlag durch Berühren von Oberflächen mit unterschiedlichem
elektrischem Potenzial zu vermeiden.
v Geräte niemals einschalten, wenn Hinweise auf Feuer, Wasser oder
Gebäudeschäden vorliegen.
v Die Verbindung zu den angeschlossenen Netzkabeln,
Telekommunikationssystemen, Netzwerken und Modems ist vor dem Öffnen
des Gehäuses zu unterbrechen, sofern in den Installations- und
Konfigurationsprozeduren keine anders lautenden Anweisungen enthalten
sind.
v Zum Installieren, Transportieren und Öffnen der Abdeckungen des
Computers oder der angeschlossenen Einheiten die Kabel gemäß der
folgenden Tabelle anschließen und abziehen.
Zum Anschließen der Kabel gehen Sie
wie folgt vor
Zum Abziehen der Kabel gehen Sie wie
folgt vor
1. Schalten Sie alle Einheiten AUS.
1. Schalten Sie alle Einheiten AUS.
2. Schließen Sie erst alle Kabel an die
2. Ziehen Sie zuerst alle Netzkabel aus den
Einheiten an.
Netzsteckdosen.
3. Schließen Sie die Signalkabel an die
3. Ziehen Sie die Signalkabel aus den
Buchsen an.
Buchsen.
4. Schließen Sie die Netzkabel an die
4. Ziehen Sie alle Kabel von den Einheiten
Steckdose an.
ab.
5. Schalten Sie die Einheit EIN.
26 Hardware Maintenance Manual
CAUTION:
Eine verbrauchte Lithiumbatterie nur durch eine Batterie mit der Teilenummer
33F8354 oder eine gleichwertige, vom Hersteller empfohlene Batterie ersetzen.
Enthält das System ein Modul mit einer Lithiumbatterie, dieses nur durch ein
Modul desselben Typs und von demselben Hersteller ersetzen. Die Batterie enthält
Lithium und kann bei unsachgemäßer Verwendung, Handhabung oder Entsorgung
explodieren.
Die Batterie nicht:
v mit Wasser in Berührung bringen.
v über 100 C erhitzen.
v reparieren oder zerlegen.
Die örtlichen Bestimmungen für die Entsorgung von Sondermüll beachten.
ACHTUNG:
Bei der Installation von Lasergeräten (wie CD-ROM-Laufwerken, DVD-
aufwerken, Einheiten mit Lichtwellenleitertechnik oder Sendern) Folgendes
beachten:
v Die Abdeckungen nicht entfernen. Durch Entfernen der Abdeckungen des
Lasergeräts können gefährliche Laserstrahlungen freigesetzt werden. Das
Gerät enthält keine zu wartenden Teile.
v Werden Steuerelemente, Einstellungen oder Durchführungen von Prozeduren
anders als hier angegeben verwendet, kann gefährliche Laserstrahlung
auftreten.
VORSICHT
Einige Lasergeräte enthalten eine Laserdiode der Klasse 3A oder 3B. Beachten
Sie Folgendes:
Laserstrahlung bei geöffneter Verkleidung. Nicht in den Strahl blicken. Keine
Lupen oder Spiegel verwenden. Strahlungsbereich meiden.
Chapter 2. Safety information 27
≥18 kg
≥32 kg
≥55 kg
ACHTUNG:
Arbeitsschutzrichtlinien beim Anheben der Maschine beachten.
ACHTUNG:
Mit dem Netzschalter an der Einheit und am Netzteil wird die Stromversorgung
für die Einheit nicht unterbrochen. Die Einheit kann auch mit mehreren
Netzkabeln ausgestattet sein. Um die Stromversorgung für die Einheit
vollständig zu unterbrechen, müssen alle zum Gerät führenden Netzkabel vom
Netz getrennt werden.
2
1
ACHTUNG:
Legen Sie auf in einem Rack montierten Einheiten keine über 82 kg schweren
Gegenstände ab.
28 Hardware Maintenance Manual
Chapter 2. Safety information 29
30 Hardware Maintenance Manual
2
1
Chapter 2. Safety information 31
PERICOLO
La corrente elettrica proveniente dai cavi di alimentazione, del telefono e di
comunicazione può essere pericolosa.
Per evitare il rischio di scosse elettriche:
v Non collegare o scollegare qualsiasi cavo oppure effettuare l’installazione, la
manutenzione o la riconfigurazione del prodotto durante un temporale.
v Collegare tutti i fili elettrici a una presa di alimentazione correttamente
cablata e dotata di messa a terra.
v Collegare alle prese elettriche appropriate tutte le apparecchiature che
verranno utilizzate per questo prodotto.
v Se possibile, utilizzare solo una mano per collegare o scollegare i cavi di
segnale.
v Non accendere assolutamente apparecchiature in presenza di incendi, perdite
d’acqua o danno strutturale.
v Scollegare i cavi di alimentazione, i sistemi di telecomunicazione, le reti e il
modem prima di aprire i coperchi del dispositivo, salvo istruzioni contrarie
relative alle procedure di installazione e configurazione.
v Collegare e scollegare i cavi come descritto nella seguente tabella quando
vengono effettuate operazioni di installazione, spostamento o apertura dei
coperchi di questo prodotto o delle unità collegate.
Per collegarsi
Per scollegarsi
1. SPEGNERE le apparecchiature.
1. SPEGNERE le apparecchiature.
2. Innanzitutto, collegare tutti i cavi alle
2. Innanzitutto, rimuovere i cavi di
unità.
alimentazione dalla presa.
3. Collegare i cavi di segnale ai connettori. 3. Rimuovere i cavi di segnale dai
connettori.
4. Collegare i cavi di alimentazione alla
presa.
4. Rimuovere tutti i cavi dalle unità.
5. Accendere l’unità.
32 Hardware Maintenance Manual
ATTENZIONE:
Quando si sostituisce la batteria al litio, utilizzare solo il Numero parte 33F8354
o un tipo di batteria equivalente consigliato dal produttore. Se sul sistema è
presente un modulo che contiene una batteria al litio, sostituirlo solo con un
tipo di modulo dello stesso tipo della stessa casa di produzione. La batteria
contiene litio e può esplodere se usata, maneggiata o smaltita in modo non
corretto.
Non:
v Gettare o immergere la batteria nell’acqua
v Riscaldarla ad una temperatura superiore ai 100 gradi C (212 gradi F)
v Smontarla, ricaricarla o tentare di ripararla
Le batterie usate vanno smaltite in accordo alla normativa in vigore (DPR 915/82
e successive disposizioni e disposizioni locali).
ATTENZIONE:
Quando vengono installati prodotti laser (quali CD-ROM, unità DVD-ROM,
unità a fibre ottiche o trasmittenti), tener presente quanto segue:
v Non rimuovere gli sportelli. L’apertura di un’unità laser può determinare
l’esposizione a radiazioni laser pericolose. All’interno dell’unità non vi sono
parti su cui effettuare l’assistenza tecnica.
v L’utilizzo di controlli, regolazioni o l’esecuzione di procedure non descritti nel
presente manuale possono provocare l’esposizione a radiazioni pericolose.
PERICOLO
Alcune unità laser contengono un diodo laser di Classe 3A o Classe 3B. Tener
presente quanto segue:
Aprendo l’unità vengono emesse radiazioni laser. Non fissare il fascio, non
guardarlo direttamente con strumenti ottici ed evitare l’esposizione al fascio.
Chapter 2. Safety information 33
≥18 kg
≥32 kg
≥55 kg
ATTENZIONE:
Prestare attenzione nel sollevare l’apparecchiatura.
ATTENZIONE:
Il pulsante di controllo dell’alimentazione presente sull’unità e l’interruttore
dell’alimentatore non disattivano l’alimentazione corrente fornita all’unità. E’
possibile che l’unità disponga di più cavi di alimentazione. Per disattivare
l’alimentazione dall’unità, accertarsi che tutti i cavi di alimentazione siano
scollegati dalla fonte di alimentazione.
2
1
ATTENZIONE:
Non collocare oggetti che pesano più di 82 kg (180 lb.) sulla parte superiore
delle unità montante nel rack.
34 Hardware Maintenance Manual
Chapter 2. Safety information 35
2
1
36 Hardware Maintenance Manual
Chapter 2. Safety information 37
PELIGRO
La corriente eléctrica procedente de cables de alimentación, teléfonos y cables de
comunicación puede ser peligrosa.
Para evitar el riesgo de descarga eléctrica:
v No conecte ni desconecte los cables ni realice ninguna tarea de instalación,
mantenimiento o reconfiguración de este producto durante una tormenta
eléctrica.
v Conecte todos los cables de alimentación a tomas de corriente debidamente
cableadas y conectadas a tierra.
v Cualquier equipo que se conecte a este producto también debe conectarse a
tomas de corriente debidamente cableadas.
v Siempre que sea posible, utilice una sola mano para conectar o desconectar los
cables de señal.
v No encienda nunca un equipo cuando hay señales de fuego, agua o daños
estructurales.
v Desconecte los cables de alimentación, los sistemas de telecomunicaciones, las
redes y los módems conectados antes de abrir las cubiertas de los dispositivos,
a menos que se indique lo contrario en los procedimientos de instalación y
configuración.
v Conecte y desconecte los cables, como se describe en la tabla siguiente,
cuando instale, mueva o abra las cubiertas de este producto o de los
dispositivos conectados.
Para conectar
Para desconectar
1. APÁGUELO todo.
1. APÁGUELO todo.
2. En primer lugar, conecte todos los
2. En primer lugar, desenchufe los cables de
cables a los dispositivos.
alimentación de las tomas de corriente.
3. Conecte los cables de señal a los
3. Desconecte los cables de señal de los
conectores.
conectores.
4. Enchufe los cables de alimentación a las 4. Desconecte todos los cables de los
tomas de corriente.
dispositivos.
5. Encienda el dispositivo.
38 Hardware Maintenance Manual
PRECAUCIÓN:
Cuando sustituya una batería de litio, utilice solamente una batería número de
pieza 33F8354 u otra de tipo equivalente recomendada por el fabricante. Si su
sistema dispone de un módulo que contiene una batería de litio, reemplácelo
sólo con el mismo tipo de módulo, del mismo fabricante. La batería contiene
litio y puede explotar si no se utiliza, manipula o desecha correctamente.
No debe:
v Arrojarla al agua o sumergirla en ella
v Exponerla a temperaturas superiores a 100°C (212°F)
v Repararla o desmontarla
Deshágase de la batería según especifiquen las leyes o normas locales.
PRECAUCIÓN:
Cuando haya productos láser (como unidades de CD-ROM, unidades de DVD,
dispositivos de fibra óptica o transmisores) instalados, tenga en cuenta lo
siguiente:
v No quite las cubiertas. Si quita las cubiertas del producto láser, podría quedar
expuesto a radiación láser peligrosa. Dentro del dispositivo no existe ninguna
pieza que requiera servicio técnico.
v Si usa controles o ajustes o realiza procedimientos que no sean los
especificados aquí, podría exponerse a radiaciones peligrosas.
PELIGRO
Algunos productos láser tienen incorporado un diodo láser de clase 3A o clase
3B. Tenga en cuenta lo siguiente:
Cuando se abre, queda expuesto a radiación láser. No mire directamente al rayo
láser, ni siquiera con instrumentos ópticos, y evite exponerse directamente al
rayo láser.
Chapter 2. Safety information 39
≥18 kg
≥32 kg
≥55 kg
PRECAUCIÓN:
Adopte procedimientos seguros al levantar el equipo.
PRECAUCIÓN:
El botón de control de alimentación del dispositivo y el interruptor de
alimentación de la fuente de alimentación no desconectan la corriente eléctrica
suministrada al dispositivo. Además, el dispositivo podría tener más de un cable
de alimentación. Para suprimir toda la corriente eléctrica del dispositivo,
asegúrese de que todos los cables de alimentación estén desconectados de la
toma de corriente.
2
1
PRECAUCIÓN:
No coloque ningún objeto que pese más de 82 Kg (180 lb) encima de
dispositivos montados en un bastidor.
40 Hardware Maintenance Manual
Chapter 3. General information
This chapter provides general information that applies to all machine types
supported by this publication.
The Access IBM program
Use the Access IBM® program for general information about the use, operation,
and maintenance of the computer. The Access IBM program also contains
information to help solve problems and get repair service or other technical
assistance. The Access IBM program is preinstalled on most ThinkCentre products.
Additional information resources
If you have Internet access, the most up-to-date information for your computer is
available from the World Wide Web.
You can find the following information:
v CRU removal and installation instructions
v Publications
v Troubleshooting information
v Parts information
v Downloads and drivers
v Links to other useful sources of information
To access this information, point your browser to http://www.lenovo.com/think/
support/.
Physical specifications
This section details the physical specifications for each computer Type.
© Lenovo 2005. Portions © IBM Corp. 2005.
41
Types 8126, 8174, 8175, and 8176
Dimensions
Height: 398 mm (15.67 in.)
Heat output (approximate) in British thermal units (Btu)
per hour:
Minimum configuration: 257 Btu/hr (75 watts)
Maximum configuration: 785 Btu/hr (230 watts)
Width: 180 mm (7.08 in.)
Depth: 402 mm (15.82 in.)
Airflow
Weight
Approximately 0.68 cubic meters every minute (24
cubic feet every minute) maximum
Minimum configuration as shipped: 7.6 kg (16.8 lb)
Maximum configuration: 9.97 kg (22 lb)
Acoustical noise-emission values
Environment
Air temperature:
For microprocessors less than 2.8 GHz:
Average sound-pressure levels:
At operator position:
System on: 10° to 35°C (50° to 95° F)
System off: 10° to 43°C (50° to 110° F)
Maximum altitude: 2134 m (7000 ft)
Note: The maximum altitude, 2134 m (7000 ft), is
the maximum altitude at which the specified air
temperatures apply. At higher altitudes, the
maximum air temperatures are lower than those
specified.
Idle: 28 dBA
Operating: 35 dBA
At bystander position - 1 meter (3.3 ft):
Idle: 25 dBA
Operating: 33 dBA
Humidity:
Declared (upper limit) sound-power levels:
Idle: 4.0 bels
System on: 8% to 80%
System off: 8% to 80%
Operating: 4.7 bels
Electrical input
For microprocessors greater than or equal to 2.8 GHz:
Average sound-pressure levels:
At operator position:
Input voltage:
Low range:
Minimum: 90 V ac
Idle: 33 dBA
Maximum: 180 V ac
Operating: 35 dBA
Input frequency: 50/60 Hz
Voltage switch setting: 115 V ac
High range:
At bystander position - 1 meter (3.3 ft):
Idle: 30 dBA
Operating: 33 dBA
Minimum: 137 V ac
Declared (upper limit) sound-power levels:
Idle: 4.4 bels
Maximum: 265 V ac
Input frequency: 50/60 Hz
Voltage switch setting: 230 V ac
Input kilovolt-amperes (kVA) (approximate):
Minimum configuration as shipped: 0.08 kVA
Maximum configuration: 0.30 kVA
Operating: 4.7 bels
Note: These levels were measured in controlled
acoustical environments according to the procedures
specified by the American National Standards Institute
(ANSI) S12.10 and ISO 7779 and are reported in
accordance with ISO 9296. Actual sound-pressure levels
in a given location might exceed the average values
stated because of room reflections and other nearby noise
sources. The declared sound-power levels indicate an
upper limit, below which a large number of computers
will operate.
Note: Power consumption and heat output vary
depending on the number and type of optional
features installed and the power-management
optional features in use.
42 Hardware Maintenance Manual
Types 8149, 8177, and 8178
Dimensions
Height: 140 mm (5.5 in.)
Heat output (approximate) in British thermal units (Btu)
per hour:
Minimum configuration: 257 Btu/hr (75 watts)
Maximum configuration: 785 Btu/hr (230 watts)
Width: 425 mm (16.7 in.)
Depth: 425 mm (16.7 in)
Airflow
Weight
Approximately 0.51 cubic meters per minute (18 cubic
feet per minute) maximum
Minimum configuration as shipped: 10.0 kg (22 lb)
Maximum configuration: 11.4 kg (25.0 lb)
Acoustical noise-emission values
Average sound-pressure levels:
At operator position:
Environment
Air temperature:
System on: 10° to 35°C (50° to 95° F)
System off: 10° to 43°C (50° to 110° F)
Idle: 30 dBA
Operating: 32 dBA
Maximum altitude: 2134 m (7000 ft)
Note: The maximum altitude, 2134 m (7000 ft), is
the maximum altitude at which the specified air
temperatures apply. At higher altitudes, the
maximum air temperatures are lower than those
specified.
At bystander position - 1 meter (3.3 ft):
Idle: 26 dBA
Operating: 30 dBA
Declared (upper limit) sound-power levels:
Idle: 4.0 bels
Humidity:
Operating: 4.3 bels
System on: 8% to 80%
System off: 8% to 80%
Note: These levels were measured in controlled
acoustical environments according to the procedures
specified by the American National Standards
Institute (ANSI) S12.10 and ISO 7779 and are reported
in accordance with ISO 9296. Actual sound-pressure
levels in a given location might exceed the average
values stated because of room reflections and other
nearby noise sources. The declared sound-power
levels indicate an upper limit, below which a large
number of computers will operate.
Electrical input
Input voltage:
Low range:
Minimum: 90 V ac
Maximum: 180 V ac
Input frequency: 50/60 Hz
Voltage switch setting: 115 V ac
High range:
Minimum: 137 V ac
Maximum: 265 V ac
Input frequency: 50/60 Hz
Voltage switch setting: 230 V ac
Input kilovolt-amperes (kVA) (approximate):
Minimum configuration as shipped: 0.08 kVA
Maximum configuration: 0.3 kVA
Note: Power consumption and heat output vary
depending on the number and type of optional
features installed and the power-management
optional features in use.
Chapter 3. General information 43
Types 8084, 8085, 8147, 8148, and 8179
Dimensions
Height: 413 mm (16.25 in.)
Heat output (approximate) in British thermal units (Btu)
per hour:
Minimum configuration: 257 Btu/hr (75 watts)
Maximum configuration: 785 Btu/hr (230 watts)
Width: 191 mm (7.5 in.)
Depth: 406 mm (16 in.)
Airflow
Weight
Approximately 0.68 cubic meters per minute (24 cubic
feet per minute) maximum
Minimum configuration as shipped: 9.1 kg (20 lb)
Maximum configuration: 11.4 kg (25.0 lb)
Acoustical noise-emission values
Average sound-pressure levels:
At operator position:
Environment
Air temperature:
System on: 10° to 35°C (50° to 95° F)
System off: 10° to 43°C (50° to 110° F)
Idle: 28 dBA
Operating: 30 dBA
Maximum altitude: 2134 m (7000 ft)
Note: The maximum altitude, 2134 m (7000 ft), is
the maximum altitude at which the specified air
temperatures apply. At higher altitudes, the
maximum air temperatures are lower than those
specified.
At bystander position - 1 meter (3.3 ft):
Idle: 26 dBA
Operating: 29 dBA
Declared (upper limit) sound-power levels:
Idle: 4.1 bels
Humidity:
Operating: 4.3 bels
System on: 8% to 80%
System off: 8% to 80%
Note: These levels were measured in controlled
acoustical environments according to the procedures
specified by the American National Standards
Institute (ANSI) S12.10 and ISO 7779 and are reported
in accordance with ISO 9296. Actual sound-pressure
levels in a given location might exceed the average
values stated because of room reflections and other
nearby noise sources. The declared sound-power
levels indicate an upper limit, below which a large
number of computers will operate.
Electrical input
Input voltage:
Low range:
Minimum: 90 V ac
Maximum: 180 V ac
Input frequency: 50/60 Hz
Voltage switch setting: 115 V ac
High range:
Minimum: 137 V ac
Maximum: 265 V ac
Input frequency: 50/60 Hz
Voltage switch setting: 230 V ac
Input kilovolt-amperes (kVA) (approximate):
Minimum configuration as shipped: 0.08 kVA
Maximum configuration: 0.3 kVA
Note: Power consumption and heat output vary
depending on the number and type of optional
features installed and the power-management
optional features in use.
44 Hardware Maintenance Manual
Chapter 4. General Checkout
Attention
The drives in the computer you are servicing might have been rearranged or
the drive startup sequence changed. Be extremely careful during write
operations such as copying, saving, or formatting. Data or programs can be
overwritten if you select an incorrect drive.
General error messages appear if a problem or conflict is found by an application
program, the operating system, or both. For an explanation of these messages, refer
to the information supplied with that software package.
Notes:
v The default is for this computer to boot up in quiet mode (no beep, no memory count
and checkpoint code display) when no errors are detected by POST.
v To enable beep, memory count, and checkpoint code display when a successful POST
occurs, do the following:
2. Select Start Options.
3. Set Power-On Self-Test to Enhanced.
v Before replacing any FRUs, ensure that the latest level of BIOS is installed on the system.
A down-level BIOS might cause false errors and unnecessary replacement of the system
board. For more information on how to determine and obtain the latest level BIOS, see
Use the following procedure to help determine the cause of the problem:
1. Power-off the computer and all external devices.
2. Check all cables and power cords.
3. Set all display controls to the middle position.
4. Power-on all external devices.
5. Power-on the computer.
v Look for displayed error codes
v Listen for beep codes
v Look for readable instructions or a main menu on the display.
6. Look at the following conditions and follow the instructions:
7. There are three LEDs to help you determine if the power supply and system
board are working correctly. A power button LED is located on the front of the
computer and two diagnostic LEDs are located on the power supply at the rear
of the computer.
a. Disconnect the power cord from the electrical outlet.
b. Reconnect the power cord to a working electrical outlet.
c. Press the power button.
© Lenovo 2005. Portions © IBM Corp. 2005.
45
d. Observe the LEDs and refer to the following table.
Green
Yellow
Power LED
diagnostic LED diagnostic LED Action
ON
ON
OFF
This is the normal condition of the LEDs when the power is
OK.
OFF
OFF
OFF
Make sure the power cord is attached to a working electrical
outlet.
If the electrical outlet is OK, replace the power supply.
Replace the system board
OFF (after the
power button
has been
ON
ON
OFF
ON
pressed)
ON
Replace the power supply
If the Diagnostic LEDs are in the normal condition and the problem persists,
replace the system board and the microprocessor, one at a time, until the
computer works correctly.
v If you receive an error, replace the part that the diagnostic program calls out
or go to “Diagnostic error codes” on page 61.
v If the test stops and you cannot continue, replace the last device tested.
Problem determination tips
Due to the variety of hardware and software combinations that can be
encountered, use the following information to assist you in problem determination.
If possible, have this information available when requesting assistance from Service
Support and Engineering functions.
v Machine type and model
v Processor or hard disk upgrades
v Failure symptom
– Do diagnostics indicate a failure?
– What, when, where, single, or multiple systems?
– Is the failure repeatable?
– Has this configuration ever worked?
– If it has been working, what changes were made prior to it failing?
– Is this the original reported failure?
v Diagnostics version
– Type and version level
v Hardware configuration
– Print (print screen) configuration currently in use
– BIOS level
v Operating system software
– Type and version level
Note: To eliminate confusion, identical systems are considered identical only if
they:
46 Hardware Maintenance Manual
1. Are the exact machine type and models
2. Have the same BIOS level
3. Have the same adapters/attachments in the same locations
4. Have the same address jumpers/terminators/cabling
5. Have the same software versions and levels
6. Have the same Diagnostics Diskette (version)
7. Have the same configuration options set in the system
8. Have the same setup for the operation system control files
Comparing the configuration and software set-up between ″working and
non-working″ systems will often lead to problem resolution.
Chapter 4. General Checkout 47
48 Hardware Maintenance Manual
Chapter 5. Diagnostics using PC-Doctor for DOS
Diagnostics are provided by the PC-Doctor program for DOS. These include a full
range of diagnostic utilities to determine the operating condition of the computer’s
hardware components.
You can the run diagnostics from the Rescue and Recovery™ workspace or you can
create a bootable diagnostic diskette from the Rescue and Recovery workspace.
Alternatively, you can download either a diskette image or a startable CD-ROM
image (.iso file) from the Customer Support Web site and run diagnostics using
them.
The latest version of the diagnostics program is available from
http://www.lenovo.com/think/support on the World Wide Web. Type your
machine type into the Use Quick path field and click Go to find the downloadable
files that are specific to the computer. See “Diagnostics program download” on
Diagnostic error messages appear when a test program finds a problem with a
hardware option. For the test programs to properly determine if a test Passed, Failed
or Aborted, the test programs check the error-return code at test completion. See
If an installed device is not recognized by the diagnostics program, that device
might be defective.
Starting PC-Doctor from the Rescue and Recovery workspace
This procedure describes how to start PC-Doctor from the Rescue and Recovery
workspace.
1. If your computer is already on when you start this procedure, shut down the
operating system and turn off the computer.
2. To launch the Rescue and Recovery workspace, repeatedly press the F11 key as
you turn on the computer.
Note: If a user password or an administrator password has been set, the
Rescue and Recovery workspace is not displayed until you type the
password.
3. When the Rescue and Recovery workspace is displayed, look for ″Troubleshoot″
on the left side of the screen. Click Diagnose hardware.
Notes:
a. Additional diagnostic information is available from the Rescue and
Recovery workspace, such as a diagnostic overview. Refer to the Rescue and
Recovery help system for details.
b. After selecting Diagnose hardware, make sure the computer is restarted
using the restart button on the Rescue and Recovery workspace. Do not use
the power switch to start the reboot.
c. You can also create a set of diagnostic disks from the Rescue and Recovery
workspace by clicking Create diagnostic disks from the Rescue and
Recovery menu.
© Lenovo 2005. Portions © IBM Corp. 2005.
49
Starting PC-Doctor from a diagnostic diskette or CD-ROM
Note: If your computer has no internal diskette drive, an external USB diskette
drive is required when using the diagnostic diskette.
1. If your computer is already on when you start this procedure, shut down the
operating system and turn off the computer.
2. Insert the diskette or CD-ROM in the appropriate drive.
3. Turn on the computer.
Note: If the PC-Doctor program fails to start, make sure that the startup device
sequence is configured to allow startup from the diskette or CD-ROM
drive. See “Selecting a startup device” on page 58.
Diagnostics program download
If you have access to the internet, you can download a diskette image or a
startable CD-ROM image (.iso file) of the diagnostics.
To download the latest diagnostics program from the WWW, do the following:
v Go to http://www.lenovo.com/think/support.
v Type the machine type in the ″Use Quick Path″ field and click Go.
v Click Downloads and drivers and scroll down to locate the Enhanced
diagnostics.
Navigating through the diagnostics programs
Use the cursor movement keys to navigate within the menus.
v The Enter key is used to select a menu item.
v The Esc key is used to back up to the previous menu.
v For online help select F1.
Running diagnostics tests
There are four ways to run the diagnostic tests.
v Using the cursor movement keys, highlight Run Normal Test or Run Quick Test
from the Diagnostics menu and then press Enter.
This automatically runs a pre-defined group of tests from each test category.
Run Normal Test runs a more extensive set of tests than does Run Quick Test
and takes longer to complete.
v From within a test category, press Ctrl-Enter to automatically run only the
v Using the cursor movement keys, highlight a single test within a test category,
and then press Enter. This runs only that test.
Press Esc at any time to stop the testing process.
Test results (N/A, PASSED, FAILED, ABORTED) are displayed in the field beside
the test description and in the test log. See “Viewing the test log” on page 54.
50 Hardware Maintenance Manual
Test selection
To select one or more tests, use the following procedure.
1. Open the corresponding test category.
2. Using the cursor movement keys, highlight the desired test.
3. Press the space bar.
A selected test is marked by >>. Pressing the space bar again de-selects a test
and removes the >>.
4. Repeat steps 2 and 3 above to select all desired tests.
Test results
Diagnostics test results produce the following error code format:
Function
Code
Failure Type DeviceID
Date
ChkDigits
Text
v Function Code:
Represents the feature or function within the PC.
v Failure Type:
Represents the type of error encountered.
v DeviceID:
Contains the component’s unit-ID which corresponds to either a fixed disk
drive, removable media drive, serial or parallel port, processor, specific RIMM,
or a device on the PCI bus.
v Date:
Contains the date when the diagnostic test was run. The date is retrieved from
CMOS and displayed using the YYYYMMDD format.
v ChkDigits:
Contains a 2-digit check-digit value to ensure the following:
– Diagnostics were run on the specified date.
– Diagnostics were run on the specified computer.
– The diagnostic error code is recorded correctly.
v Text:
Description of the error.
Fixed disk advanced test (FDAT)
PC-Doctor Fixed-Disk1 Advanced Test module (FDAT) is a full-featured highly
configurable fixed-disk test suite. The configurable capabilities of FDAT allow
users to enable or disable specific tests, enable or disable testing features, control
the test log detail, alter testing parameters, and so on. FDAT tests for and reports
most commonly found errors on a fixed-disk drive and is able to test up to 128
SCSI and 4 IDE drives (up to 132 total drives).
Drive information is gathered through FDAT’s enumeration of available devices
and user specific configuration parameters located in the FDAT.INI. FDAT uses
information supplied by these features to indicate specifically what devices are
1. The terms fixed disk and hard disk are used interchangeably.
Chapter 5. Diagnostics using PC-Doctor for DOS 51
available for test, what tests are available for the device, device properties, and so
on. To change testing parameters, you modify the FDAT.INI file in PC Doctor for
DOS.
FDAT consists of the following subtests and features.
Fixed-Disk Tests:
v Seek Tests: - checks the physical operation of the drive head.
– Linear Seek
– Random Seek
– Min-Max Seek
– Butterfly Seek
v Verify Tests: - checks the integrity of the data present on the media.
– Linear Verify
– Random Verify
v Surface Scan Tests: - checks the drive media for defects.
– Surface Scan (Linear)
– Surface Scan (Aggressive) - this is disabled for normal customer use.
– Surface Scan (Random)
v Self-monitoring, Analysis and Reporting Technology (SMART) - checks the
SMART functionality for drives that support SMART.
– Start SMART Self-Test
Other Test Features:
v Write-Splice Repair - detects and corrects Error Correction Code errors during
Verify tests.
v Auto Spin Down - a gradual spin down of the drive platters to avoid damaging
the media.
v Manufacturer Log - an in-depth manufacturer supported log of errors on the
drive.
Multitasking:
To allow simultaneous testing of multiple hard drives whenever possible, the
FDAT module is written as a set of multitasking functions. Each drive under test
can run the same test or run a different test at the same time. Each subtest is
written to handle a single test pass and all test variables are kept track of in a
structure unique for each drive.
However, when testing IDE drives, FDAT will not perform simultaneous testing of
IDE drives that are attached to the same IDE cable. For example, if FDAT is testing
four IDE drives on a PC, it will perform simultaneous testing on drives 1 and 3
first (master drives), then perform tests on 2 and 4 (slave drives). FDAT will also
perform simultaneous testing on a master and slave that are on separate IDE
cables, but will not perform simultaneous tests on a master and slave on the same
IDE cable. This generally increases the amount of time needed to test multiple IDE
drives.
Another limitation of FDAT’S multitasking capability is the use of Ultra DMA
(UDMA). Only one drive at a time can access the UDMA channel and the UDMA
52 Hardware Maintenance Manual
channel buffer must be kept high in order to maintain a speed advantage over
other data transfer modes. In order to use the UDMA channel during testing, users
must disable the multitasking feature.
Destructive versus non-destructive testing:
Most of the tests found in FDAT are non-destructive. This means that PC-Doctor
program will preserve any data that is present on the tested media prior to
beginning any destructive operations (such as write operations). However, users
can run certain tests in destructive mode (i.e. surface scan tests). Destructive tests
will speed up testing because FDAT does not preserve the data on the media prior
to the test beginning. Unlike non-destructive tests, any data present on the media
prior to the test beginning is lost.
FDAT allows for enabling or disabling destructive tests, as well as specifying a
range of destructive and non-destructive sectors on the tested drive. This is done
through the configuration of the FDAT.INI. If destructive and non-destructive
ranges somehow overlap, then the overlapped area is considered non-destructive.
For example, if users specify both destructive and non-destructive ranges as the
same, then the entire drive is tested as non-destructive.
Quick and Full erase - hard drive
The diagnostics program offers two hard drive format utilities:
v Quick Erase Hard Drive
v Full Erase Hard Drive
The Quick Erase Hard Drive provides a DOS utility that performs the following:
v Destroys the Master Boot Record (MBR) on the hard drive.
v Destroys all copies of the FAT Table on all partitions (both the master and
backup).
v Destroys the partition table.
v Provides messages that warn the user that this is a non-recoverable process.
Chapter 5. Diagnostics using PC-Doctor for DOS 53
The Full Erase Hard Drive provides a DOS utility that performs the following:
v Performs all the steps in Quick Erase.
v Provides a DOS utility that writes random data to all sectors of the hard drive.
v Provides an estimate of time to completion along with a visual representation of
completion status.
v Provides messages that warn the user about non-recoverable process.
Important: Make sure that all data is backed up before using the Quick or Full Erase
functions.
To select the Quick Erase or Full Erase Hard Drive utility, use the following
procedure:
1. Select the UTILITY option on the toolbar and press Enter.
2. Select either the QUICK ERASE or FULL ERASE HARD DISK option and
follow the instructions.
Viewing the test log
Errors reported by the diagnostic test will be displayed by the program as a failed
test.
To view details of a failure or to view a list of test results, use the following
procedure from any test category screen:
1. Press F3 to activate the log file.
2. Press F3 again to save the file to diskette or press F2 to print the file.
54 Hardware Maintenance Manual
Chapter 6. Using the Setup Utility
The Setup Utility program is stored in the electrically erasable programmable
read-only memory (EEPROM) of the computer. The Setup Utility program is used
to view and change the configuration settings of the computer, regardless of which
operating system you are using. However, the operating-system settings might
override any similar settings in the Setup Utility program.
Starting the Setup Utility program
To start the Setup Utility program, do the following:
1. If your computer is already on when you start this procedure, shut down the
operating system and turn off the computer.
2. Repeatedly press the F1 key as you turn on the computer.
Notes:
a. If a password has been set, the Setup Utility program menu is not displayed
information.
b. BIOS settings cannot be changed without the correct password.
c. The Setup Utility might start automatically when the power-on self-test
(POST) detects that hardware has been removed or new hardware has been
installed in your computer.
Viewing and changing settings
The Setup Utility program menu lists items that identify system configuration
topics.
When working with the Setup Utility program menu, you must use the keyboard.
The keys used to perform various tasks are displayed at the bottom of each screen.
Exiting from the Setup Utility program
When you finish viewing or changing settings, press Esc to return to the Setup
Utility program menu (you might have to press Esc several times). If you want to
save the new settings, press F10.
Using passwords
By using the Setup Utility program, you can set passwords to prevent
unauthorized persons from gaining access to your computer and data. The types of
passwords used are:
v User Password
v Administrator Password
v IDE Drive User Password (some computers)
v IDE Drive Master Password (some computers)
You do not have to set any passwords to use your computer. However, if you
decide to set any passwords, read the following sections.
© Lenovo 2005. Portions © IBM Corp. 2005.
55
Password considerations
If you are setting any of the various types of passwords on your computer, you
should read and understand the following information:
v If you type an incorrect password, you will see an error message. If you type an
incorrect password three consecutive times, you must turn the computer off and
start again.
v If you set both a User Password and an IDE Drive User Password to the same
string, you will be prompted for the password only once when you turn on your
computer.
v Do not move an internal IDE hard disk drive to another computer if an IDE
Drive User Password has been set unless that computer also supports the IDE
Drive User Password.
v If your computer is connected to a local area network (LAN), Wake on LAN will
not work unless both a User Password and an IDE Drive User Password are set
using the same password.
User Password
When a User Password is set, the user is prompted to type a valid password each
time the computer is turned on. The computer cannot be used until a valid
password is typed from the keyboard.
Administrator Password
Setting an Administrator Password deters unauthorized persons from changing
configuration settings. If you are responsible for maintaining the settings of several
computers, you might want to set an Administrator Password.
After you set an Administrator Password, a password prompt is displayed each
time you try to access the Setup Utility program.
If both the user and administrator passwords are set, you can type either
password. However, to change any configuration settings, you must use your
administrator password.
IDE Drive User Password
The IDE Drive User Password, used on some computers, is used to protect the
data on the IDE hard disk drive(s). When this password is set, you are prompted
to type a valid password before any hard disk drive can be used. This prompt is
displayed each time you turn on your computer. If your computer has multiple
hard disk drives, they all must use the same password.
Attention
If an IDE Drive User Password is set but the IDE Drive Master Password is
not set, there is no recovery in the event that the IDE Drive User Password is
lost or forgotten. The hard disk drive must be replaced. See “IDE Drive
IDE Drive Master Password
The IDE Drive Master Password, used on some computers, is used to recover use
of the hard disk drive in the event that the IDE Drive User Password is lost or
forgotten. Only the person who knows the IDE Drive Master password can reset
the IDE Drive User Password.
56 Hardware Maintenance Manual
Attention
Make sure that the IDE Drive Master password is stored in a safe place. If
both the IDE Drive User password and the IDE Drive Master password are
lost or forgotten, the IDE hard disk drive must be replaced.
If both the IDE Drive User Password and the IDE Drive Master Password are to be
set, the IDE Drive Master Password must be set before setting the IDE Drive User
Password.
Setting, changing, and deleting a password
To set, change, or delete a password, do the following:
Note: A password can be any combination of up to seven characters (A- Z, a-z,
and 0-9).
2. From the Setup Utility program menu, select Security.
3. Select Set Passwords. Read the information displayed on the right side of the
screen.
Using Security Profile by Device
Security Profile by Device is used to enable or disable user access to the following
devices:
IDE controller
When this feature is set to Disable, all devices connected to the
IDE controller (such as hard disk drives or the CD-ROM drive)
are disabled and will not be displayed in the system
configuration.
Diskette Drive Access
Diskette Write Protect
When this feature is set to Disable, the diskette drive cannot be
accessed.
When this feature is set to Enable, all diskettes are treated as if
they are write-protected.
To set Security Profile by Device, do the following:
2. From the Setup Utility program menu, select Security.
3. Select Security Profile by Device.
4. Select the desired devices and settings and press Enter.
5. Return to the Setup Utility program menu, select Exit, and then Save Settings
or Save and exit the Setup Utility.
Note: If you do not want to save the settings, select Exit the Setup Utility
without saving.
Chapter 6. Using the Setup Utility 57
Selecting a startup device
If the computer does not start up (boot) from a device such as the CD-ROM,
diskette, or hard disk as expected, use one of the following procedures to select a
startup device.
Selecting a temporary startup device
Use this procedure to startup from any boot device.
Note: Not all CDs, hard disks, and diskettes are startable (bootable).
1. If your computer is already on when you start this procedure, shut down the
operating system and turn off the computer.
2. To open the Startup Device Menu, repeatedly press the F12 key as you turn on
the computer.
Note: Selecting a startup device from this list does not permanently change the
startup sequence; it is valid for one boot cycle only.
Changing the startup device sequence
To view or permanently change the configured startup device sequence, do the
following:
2. Select Startup.
3. Select Startup Sequence. See the information displayed on the right side of the
screen.
4. Select the devices for the Primary Startup Sequence, the Automatic Startup
Sequence, and the Error Startup Sequence.
5. Select Exit from the Setup Utility menu and then Save Settings or Save and
exit the Setup Utility.
If you have changed these settings and want to return to the default settings, select
Load Default Settings on the Exit menu.
Advanced settings
On some computer models the Advanced settings menu includes a setting to
Enable/Disable HyperThreading. This feature works only with
HyperThreading-aware operating systems such as Microsoft® Windows® XP. The
default setting for HyperThreading is Enabled. However, if you select Set Defaults
and are using an operating system other than Windows XP, the computer
performance might be degraded. Therefore, you should always set
HyperThreading to Disabled unless you are sure your operating system supports
HyperThreading.
58 Hardware Maintenance Manual
Chapter 7. Symptom-to-FRU Index
The Symptom-to-FRU index lists error symptoms and possible causes. The most
likely cause is listed first. Always begin with Chapter 4, “General Checkout,” on
page 45. This index can also be used to help you decide which FRUs to have
available when servicing a computer. If you are unable to correct the problem
using this index, go to “Undetermined problems” on page 90.
Notes:
v If you have both an error message and an incorrect audio response, diagnose the error
message first.
v If you cannot run the diagnostic tests or you get a diagnostic error code when running a
test, but did receive a POST error message, diagnose the POST error message first.
v If you did not receive any error message, look for a description of your error symptoms
in the first part of this index.
v Check the hard disk drive jumper settings before you replace a hard disk drive.
Hard disk drive boot error
A hard disk drive boot error (error codes 1962 and I999030X) can have the
following causes.
Error
FRU/Action
The start-up drive is not in the boot
sequence in configuration.
Check the configuration and ensure the
start-up drive is in the boot sequence.
No operating system installed on the boot
drive.
Install an operating system on the boot
drive.
The boot sector on the start-up drive is
corrupted.
The drive must be formatted, do the
following:
1. Attempt to back-up the data on the
failing hard disk drive.
2. Using the operating systems programs,
format the hard disk drive.
The drive is defective.
Replace the hard disk drive.
Power Supply Errors
If you suspect a power problem, use the following procedures.
Check/Verify
FRU/Action
Check the following for proper installation.
v Power Cord
Reseat connectors
v On/Off Switch connector
v On/Off Switch Power Supply connector
v System Board Power Supply connectors
v Microprocessor(s) connection
Check the power cord for continuity.
Power Cord
Check the power-on switch for continuity.
Power-on Switch
© Lenovo 2005. Portions © IBM Corp. 2005.
59
1. Turn off the computer and disconnect all external devices.
2. Power-on the computer.
3. There are three LEDs to help you determine if the power supply and system
board are working correctly. The power button LED is located on the front of
the computer and the two diagnostic LEDs are located on the power supply at
the rear of the computer. After pressing the power button, observe the LEDs
and refer to the following table:
Green
Yellow
Power LED
diagnostic LED diagnostic LED Action
ON
ON
OFF
This is the normal condition of the LEDs when the power is
OK.
OFF
OFF
OFF
v Make sure the power cord is attached to a working
electrical outlet.
v Check the power cord for continuity.
v If the problem persists, replace the power supply.
OFF (after the
power button
has been
ON
ON
OFF
ON
Replace the system board
pressed)
ON
Replace the power supply
If the Diagnostic LEDs are in the normal condition and the problem persists,
replace the system board and the microprocessor, one at a time, until the
computer works correctly.
60 Hardware Maintenance Manual
Diagnostic error codes
Refer to the following diagnostic error codes when using the diagnostic tests. See
“Running diagnostics tests” on page 50 for the specific type for information about
the Diagnostic programs.
In the following index, X can represent any number.
Diagnostic Error Code
FRU/Action
No action
000-000-XXX
BIOS Test Passed
000-002-XXX
BIOS Timeout
2. System board
000-024-XXX
BIOS Addressing test failure
2. System board
000-025-XXX
BIOS Checksum Value error
2. Boot block
3. System board
000-026-XXX
FLASH data error
2. Boot block
3. System board
000-027-XXX
BIOS Configuration/Setup error
1. Run Setup
3. Boot block
4. System board
000-034-XXX
BIOS Buffer Allocation failure
1. Reboot the system
3. Run memory test
4. System board
000-035-XXX
BIOS Reset Condition detected
2. System board
000-036-XXX
BIOS Register error
2. Boot block
3. System board
000-038-XXX
BIOS Extension failure
2. Adapter card
3. System board
Chapter 7. Symptom-to-FRU Index 61
Diagnostic Error Code
FRU/Action
000-039-XXX
BIOS DMI data error
2. System board
000-195-XXX
Information only
BIOS Test aborted by user
Re-start the test, if necessary
000-196-XXX
BIOS test halt, error threshold exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
000-197-XXX
BIOS test warning
1. Make sure the component that is called
out is connected and/or enabled. See
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
000-198-XXX
BIOS test aborted
1. Make sure the component that is called
out is connected and/or enabled. See
000-199-XXX
BIOS test failed, cause unknown
2. Flash the system and re-test
3. Replace component under function test
000-250-XXX
BIOS APM failure
2. System board
000-270-XXX
BIOS ACPI failure
2. System board
001-000-XXX
No action
System Test Passed
001-00X-XXX
System Error
System board
System board
System board
001-01X-XXX
System Error
001-024-XXX
System Addressing test failure
001-025-XXX
System Checksum Value error
2. System board
001-026-XXX
System FLASH data error
2. System board
62 Hardware Maintenance Manual
Diagnostic Error Code
FRU/Action
001-027-XXX
System Configuration/Setup error
1. Run Setup
3. System board
001-032-XXX
System board
System Device Controller failure
001-034-XXX
System Device Buffer Allocation failure
1. Reboot the system
3. Run memory test
4. System board
001-035-XXX
System board
System Device Reset condition detected
001-036-XXX
System board
System Register error
001-038-XXX
System Extension failure
1. Adapter card
2. System board
001-039-XXX
System DMI data structure error
2. System board
001-040-XXX
System IRQ failure
1. Power-off/on system and re-test
2. System board
001-041-XXX
System DMA failure
1. Power-off/on system and re-test
2. System board
001-195-XXX
Information only
System Test aborted by user
Re-start the test, if necessary
001-196-XXX
System test halt, error threshold exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
001-197-XXX
System test warning
1. Make sure the component that is called
out is connected and/or enabled. See
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
001-198-XXX
System test aborted
1. If a component is called out, make sure
it is connected and/or enabled. See
Chapter 7. Symptom-to-FRU Index 63
Diagnostic Error Code
FRU/Action
001-199-XXX
System test failed, cause unknown
2. Flash the system and re-test
3. Replace component under function test
001-250-XXX
System board
System ECC error
001-254-XXX
001-255-XXX
001-256-XXX
001-257-XXX
System DMA error
System board
001-260-XXX
System board
001-264-XXX
System IRQ error
001-268-XXX
System IRQ1 failure
1. Device on IRQ1
2. System board
001-269-XXX
System IRQ2 failure
1. Device on IRQ2
2. System board
001-270-XXX
System IRQ3 failure
1. Device on IRQ3
2. System board
001-271-XXX
System IRQ4 failure
1. Device on IRQ4
2. System board
001-272-XXX
System IRQ5 failure
1. Device on IRQ5
2. System board
001-273-XXX
System IRQ6
(diskette drive) failure
1. Diskette Cable
2. Diskette drive
3. System board
001-274-XXX
System IRQ7 failure
1. Device on IRQ7
2. System board
001-275-XXX
System IRQ8 failure
1. Device on IRQ8
2. System board
001-276-XXX
System IRQ9 failure
1. Device on IRQ9
2. System board
001-277-XXX
System IRQ10 failure
1. Device on IRQ10
2. System board
001-278-XXX
System IRQ11 failure
1. Device on IRQ11
2. System board
001-279-XXX
System IRQ12 failure
1. Device on IRQ12
2. System board
001-280-XXX
System IRQ13 failure
1. Device on IRQ13
2. System board
64 Hardware Maintenance Manual
Diagnostic Error Code
FRU/Action
001-281-XXX
System IRQ14
(hard disk drive) failure
1. Hard disk drive cable
2. Hard disk drive
3. System board
001-282-XXX
System IRQ15 failure
1. Device on IRQ15
2. System board
001-286-XXX
System board
001-287-XXX
001-288-XXX
System Timer failure
001-292-XXX
System CMOS
RAM error
1. Run Setup and re-test
2. System board
001-293-XXX
System CMOS Battery
1. Battery
2. System board
001-298-XXX
System RTC date/time update failure
2. System board
001-299-XXX
System board
System RTC periodic interrupt failure
001-300-XXX
System board
System RTC Alarm failure
001-301-XXX
System RTC Century byte error
2. System board
005-000-XXX
No action
Video Test Passed
005-00X-XXX
Video error
1. Video card, if installed
2. System board
005-010-XXX
005-011-XXX
005-012-XXX
1. Video card, if installed
2. System board
005-013-XXX
Video Signal failure
005-016-XXX
Video Simple Pattern
test failure
1. Video Ram
2. Video card, if installed
3. System board
005-024-XXX
Video Addressing test failure
1. Video card, if installed
2. System board
005-025-XXX
Video Checksum Value error
1. Video card, if installed
2. System board
005-027-XXX
Video Configuration/Setup error
1. Run Setup
2. Video drivers update
3. Video card, if installed
4. System board
Chapter 7. Symptom-to-FRU Index 65
Diagnostic Error Code
FRU/Action
005-031-XXX
Video Device Cable failure
1. Video cable
2. Monitor
3. Video card, if installed
4. System board
005-032-XXX
Video Device Controller failure
1. Video card, if installed
2. System board
005-036-XXX
Video Register error
1. Video card, if installed
2. System board
005-038-XXX
System BIOS extension failure
1. Video card, if installed
2. System board
005-040-XXX
Video IRQ failure
1. Video card, if installed
2. System board
005-195-XXX
Information only
Video Test aborted by user
Re-start the test, if necessary
005-196-XXX
Video test halt, error threshold exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
005-197-XXX
Video test warning
1. Make sure the component that is called
out is connected and/or enabled. See
2. Re-run test
3. Replace the component called out in
warning statement
4. Replace the component under test
005-198-XXX
Video test aborted
1. If a component is called out, make sure
it is connected and/or enabled. See
005-199-XXX
Video test failed, cause unknown
3. Replace component under function test
005-2XX-XXX
005-3XX-XXX
Video subsystem error
1. Video card, if installed
2. System board
006-000-XXX
No action
Diskette interface Test Passed
006-0XX-XXX
Diskette interface error
1. Diskette drive Cable
2. Diskette drive
3. System board
66 Hardware Maintenance Manual
Diagnostic Error Code
FRU/Action
006-195-XXX
Information only
Diskette interface Test aborted by user
Re-start the test, if necessary
006-196-XXX
Diskette interface test halt, error threshold
exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
006-197-XXX
Diskette interface test warning
1. If a component is called out, make sure
it is connected and/or enabled
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
006-198-XXX
Diskette interface test aborted
1. If a component is called out, make sure
it is connected and/or enabled
006-199-XXX
Diskette interface test failed, cause unknown
2. Flash the system and re-test
3. Replace component under function test
006-25X-XXX
Diskette interface Error
1. Diskette drive cable
2. Diskette drive
3. System board
011-000-XXX
No action
Serial port Interface Test Passed
011-001-XXX
Serial port Presence
1. Remove external serial device, if
present
2. Run setup, enable port
3. System board
011-002-XXX
System board
011-003-XXX
Serial port Timeout/Parity error
011-013-XXX
System board
011-014-XXX
Serial port Control Signal/Loopback test
failure
011-015-XXX
Serial port External Loopback failure
1. Wrap plug
2. System board
011-027-XXX
Serial port Configuration/Setup error
1. Run Setup, enable port
3. System board
011-03X-XXX
System board
011-04X-XXX
Serial port failure
Chapter 7. Symptom-to-FRU Index 67
Diagnostic Error Code
FRU/Action
011-195-XXX
Information only
Serial port Test aborted by user
Re-start the test, if necessary
011-196-XXX
Serial port test halt, error threshold exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
011-197-XXX
Serial port test warning
1. Make sure the component that is called
out is connected and/or enabled. See
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
011-198-XXX
Serial port test aborted
1. If a component is called out, make sure
it is connected and/or enabled. See
011-199-XXX
Serial port test failed, cause unknown
3. Replace component under function test
011-2XX-XXX
Serial port signal failure
1. External serial device
2. System board
014-000-XXX
No action
Parallel port Interface Test Passed
014-001-XXX
Parallel port Presence
1. Remove external parallel device, if
present
2. Run setup, enable port
3. System board
014-002-XXX
System board
014-003-XXX
Parallel port Timeout/Parity error
014-013-XXX
System board
014-014-XXX
Parallel port Control Signal/Loopback test
failure
014-015-XXX
Parallel port External Loopback failure
1. Wrap plug
2. System board
014-027-XXX
Parallel port Configuration/Setup error
1. Run Setup, enable port
3. System board
68 Hardware Maintenance Manual
Diagnostic Error Code
FRU/Action
014-03X-XXX
System board
014-04X-XXX
Parallel port failure
014-195-XXX
Information only
Parallel port Test aborted by user
Re-start the test, if necessary
014-196-XXX
Parallel port test halt, error threshold
exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
014-197-XXX
Parallel port test warning
1. Make sure the component that is called
out is connected and/or enabled. See
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
014-198-XXX
Parallel port test aborted
1. If a component is called out, make sure
it is connected and/or enabled
014-199-XXX
Parallel port test failed, cause unknown
3. Replace component under function test
014-2XX-XXX
014-3XX-XXX
Parallel port failure
1. External parallel device
2. System board
015-000-XXX
No action
USB port Interface Test Passed
015-001-XXX
USB port Presence
1. Remove USB device(s) and re-test
2. System board
015-002-XXX
USB port Timeout
1. Remove USB device(s) and re-test
2. System board
015-015-XXX
USB port External Loopback failure
1. Remove USB device(s) and re-test
2. System board
015-027-XXX
USB port Configuration/Setup error
2. System board
015-032-XXX
System board
USB port Device Controller failure
Chapter 7. Symptom-to-FRU Index 69
Diagnostic Error Code
FRU/Action
015-034-XXX
USB port buffer
allocation failure
1. Reboot the system
3. Run memory test
4. System board
015-035-XXX
USB port Reset condition detected
1. Remove USB device(s) and re-test
2. System board
015-036-XXX
System board
USB port Register error
015-040-XXX
USB port IRQ failure
1. Run setup and check for conflicts
3. System board
015-195-XXX
Information only
USB port Test aborted by user
Re-start the test, if necessary
015-196-XXX
USB port test halt, error threshold exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
015-197-XXX
USB port test warning
1. Make sure the component that is called
out is connected and/or enabled. See
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
015-198-XXX
USB port test aborted
1. If a component is called out, make sure
it is connected and/or enabled. See
015-199-XXX
USB port test failed, cause unknown
3. Replace component under function test
018-000-XXX
No action
PCI Card Test Passed
018-0XX-XXX
PCI Card Failure
1. Riser card, if installed
2. System board
018-195-XXX
PCI Card Test aborted by user
1. PCI card
2. Information only
Re-start the test, if necessary
70 Hardware Maintenance Manual
Diagnostic Error Code
FRU/Action
018-196-XXX
PCI Card test halt, error threshold exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
018-197-XXX
PCI Card test warning
1. Make sure the component that is called
out is connected and/or enabled. See
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
018-198-XXX
PCI Card test aborted
1. If a component is called out, make sure
it is connected and/or enabled. See
018-199-XXX
PCI Card test failed, cause unknown
3. Replace component under function test
018-250-XXX
PCI Card Services error
1. PCI card
2. Riser card, if installed
3. System board
020-000-XXX
No action
PCI Interface Test Passed
020-0XX-XXX
PCI Interface error
1. PCI card
2. Riser card, if installed
3. System board
020-195-XXX
Information only
PCI Test aborted by user
Re-start the test, if necessary
020-196-XXX
PCI test halt, error threshold exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
020-197-XXX
PCI test warning
1. Make sure the component that is called
out is connected and/or enabled. See
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
Chapter 7. Symptom-to-FRU Index 71
Diagnostic Error Code
FRU/Action
020-198-XXX
PCI test aborted
1. If a component is called out, make sure
it is connected and/or enabled. See
020-199-XXX
PCI test failed, cause unknown
3. Replace component under function test
020-262-XXX
PCI system error
1. PCI card
2. Riser card, if installed
3. System board
025-000-XXX
No action
IDE interface Test Passed
025-00X-XXX
025-01X-XXX
IDE interface failure
1. IDE signal cable
2. Check power supply voltages
3. Reseat IDE signal cable
4. IDE device
5. System board
025-027-XXX
IDE interface Configuration/Setup error
1. IDE signal cable
3. Reseat IDE signal cable
4. IDE device
5. System board
025-02X-XXX
025-03X-XXX
025-04X-XXX
IDE Interface failure
1. IDE signal cable
2. Check power supply
3. Reseat IDE signal cable
4. IDE device
5. System board
025-195-XXX
Information only
IDE interface Test aborted by user
Re-start the test, if necessary
025-196-XXX
IDE interface test halt, error threshold
exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
025-197-XXX
IDE interface test warning
1. Make sure the component that is called
out is connected and/or enabled. See
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
72 Hardware Maintenance Manual
Diagnostic Error Code
FRU/Action
025-198-XXX
IDE interface test aborted
1. If a component is called out, make sure
it is connected and/or enabled. See
025-199-XXX
IDE interface test failed, cause unknown
3. Replace component under function test
030-000-XXX
No action
SCSI interface Test Passed
030-00X-XXX
030-01X-XXX
SCSI interface failure
1. SCSI signal cable
2. Check power supply
3. SCSI device
4. SCSI adapter card, if installed
5. System board
030-027-XXX
SCSI interface Configuration/Setup error
1. SCSI signal cable
3. SCSI device
4. SCSI adapter card, if installed
5. System board
030-03X-XXX
030-04X-XXX
SCSI interface error
1. SCSI signal cable
2. Check power supply
3. SCSI device
4. SCSI adapter card, if installed
5. System board
030-195-XXX
Information only
SCSI interface Test aborted by user
Re-start the test, if necessary
030-196-XXX
SCSI interface test halt, error threshold
exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
030-197-XXX
SCSI interface test warning
1. Make sure the component that is called
out is connected and/or enabled. See
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
Chapter 7. Symptom-to-FRU Index 73
Diagnostic Error Code
FRU/Action
030-198-XXX
SCSI interface test aborted
1. If a component is called out, make sure
it is connected and/or enabled. See
030-199-XXX
SCSI interface test failed, cause unknown
3. Replace component under function test
035-000-XXX
No action
RAID interface Test Passed
035-0XX-XXX
RAID interface Failure
1. RAID signal cable
2. RAID device
3. RAID adapter card, if installed
4. System board
035-195-XXX
Information only
RAID interface Test aborted by user
Re-start the test, if necessary
035-196-XXX
RAID interface test halt, error threshold
exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
035-197-XXX
RAID interface test warning
1. Make sure the component that is called
out is connected and/or enabled. See
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
035-198-XXX
RAID interface test aborted
1. If a component is called out, make sure
it is connected and/or enabled. See
035-199-XXX
RAID interface test failed, cause unknown
3. Replace component under function test
071-000-XXX
No action
Audio port Interface Test Passed
74 Hardware Maintenance Manual
Diagnostic Error Code
FRU/Action
071-00X-XXX
071-01X-XXX
071-02X-XXX
Audio port error
1. Run Setup
3. System board
071-03X-XXX
Audio port failure
1. Speakers
2. Microphone
3. Audio card, if installed
4. System board
071-04X-XXX
Audio port failure
1. Run Setup
2. Audio card, if installed
3. System board
071-195-XXX
Information only
Audio port Test aborted by user
Re-start the test, if necessary
071-196-XXX
Audio port test halt, error threshold
exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
071-197-XXX
Audio port test warning
1. Make sure the component that is called
out is connected and/or enabled. See
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
071-198-XXX
Audio port test aborted
1. If a component is called out, make sure
it is connected and/or enabled. See
071-199-XXX
Audio port test failed, cause unknown
3. Replace component under function test
071-25X-XXX
Audio port failure
1. Speakers
2. Audio card, if installed
3. System board
080-000-XXX
No action
Game Port interface Test Passed
080-XXX-XXX
Game Port interface Error
1. Remove the game port device and
re-test the system
080-195-XXX
Information only
Game Port interface Test aborted by user
Re-start the test, if necessary
Chapter 7. Symptom-to-FRU Index 75
Diagnostic Error Code
FRU/Action
080-196-XXX
Game Port interface test halt, error threshold
exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
080-197-XXX
Game Port interface test warning
1. Make sure the component that is called
out is connected and/or enabled. See
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
080-198-XXX
Game Port interface test aborted
1. If a component is called out, make sure
it is connected and/or enabled. See
080-199-XXX
Game Port interface test failed, cause
unknown
3. Replace component under function test
086-000-XXX
No action
Mouse Port interface Test Passed
086-001-XXX
Mouse Port interface Presence
1. Mouse
2. System board
086-032-XXX
Mouse Port interface Device controller
failure
1. Mouse
2. System board
086-035-XXX
Mouse Port interface Reset
1. Mouse
2. System board
086-040-XXX
Mouse Port interface IRQ failure
1. Run Setup
2. Mouse
3. System board
086-195-XXX
Information only
Mouse Port interface Test aborted by user
Re-start the test, if necessary
086-196-XXX
Mouse Port interface test halt, error
threshold exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
76 Hardware Maintenance Manual
Diagnostic Error Code
FRU/Action
086-197-XXX
Mouse Port interface test warning
1. Make sure the component that is called
out is connected and/or enabled. See
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
086-198-XXX
Mouse Port interface test aborted
1. If a component is called out, make sure
it is connected and/or enabled. See
086-199-XXX
Mouse Port interface test failed, cause
unknown
3. Replace component under function test
089-000-XXX
No action
Microprocessor Test Passed
089-XXX-XXX
Microprocessor failure
1. Microprocessor(s)
2. System board
089-195-XXX
Information only
Microprocessor Test aborted by user
Re-start the test, if necessary
089-196-XXX
Microprocessor test halt, error threshold
exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
089-197-XXX
Microprocessor test warning
1. Make sure the component that is called
out is connected and/or enabled. See
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
089-198-XXX
Microprocessor test aborted
089-199-XXX
Microprocessor test failed, cause unknown
3. Replace component under function test
170-000-XXX
No action
Voltage Sensor(s) Test Passed
Chapter 7. Symptom-to-FRU Index 77
Diagnostic Error Code
FRU/Action
170-0XX-XXX
Voltage Sensor(s) failure
1. Flash system
2. System board
170-195-XXX
Information only
Voltage Sensor(s) Test aborted by user
Re-start the test, if necessary
170-196-XXX
Voltage Sensor(s) test halt, error threshold
exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
170-197-XXX
Voltage Sensor(s) test warning
1. Make sure the component that is called
out is connected and/or enabled. See
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
170-198-XXX
Voltage Sensor(s) test aborted
1. If a component is called out, make sure
it is connected and/or enabled. See
170-199-XXX
Voltage Sensor(s) test failed, cause unknown
3. Replace component under function test
170-250-XXX
170-251-XXX
Voltage Sensor(s) Voltage limit error
1. Power supply
2. System board
170-254-XXX
Voltage Sensor(s) Voltage Regulator Module
error
1. Voltage Regulator Module (VRM)
2. Microprocessor
3. System board
175-000-XXX
No action
Thermal Sensor(s) Test Passed
175-0XX-XXX
Thermal Sensor(s) failure
1. Flash system
2. System board
175-195-XXX
Information only
Thermal Sensor(s) Test aborted by user
Re-start the test, if necessary
175-196-XXX
Thermal Sensor(s) test halt, error threshold
exceeded
1. Press F3 to review the log file
2. Re-start the test to reset the log file
78 Hardware Maintenance Manual
Diagnostic Error Code
FRU/Action
175-197-XXX
Thermal Sensor(s) test warning
1. Make sure the component that is called
out is connected and/or enabled. See
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
175-198-XXX
Thermal Sensor(s) test aborted
1. If a component is called out, make sure
it is connected and/or enabled
175-199-XXX
Thermal Sensor(s) test failed, cause
unknown
3. Replace component under function test
175-250-XXX
175-251-XXX
Thermal Sensor(s) limit error
1. Check fans
2. Check Power supply voltages
3. Microprocessor
4. System board
185-000-XXX
No action
Asset Security Test Passed
185-XXX-XXX
Asset Security failure
1. Flash system
2. System board
185-278-XXX
Asset Security Chassis Intrusion
1. Assure Asset Security Enabled
2. C2 Cover Switch
3. System board
201-000-XXX
No action
System Memory Test Passed
201-XXX-XXX
System Memory error
1. Replace the memory module called out
by the test
2. System board
202-000-XXX
No action
System Cache Test Passed
202-XXX-XXX
System Cache error
1. Cache, if removable
2. System board
3. Microprocessor
206-000-XXX
No action
Diskette Drive Test Passed
206-XXX-XXX
Diskette Drive error
1. Diskette Drive Cable
2. Check power supply voltages
3. Diskette drive
4. System board
Chapter 7. Symptom-to-FRU Index 79
Diagnostic Error Code
FRU/Action
No action
215-000-XXX
CD-ROM Drive Test Passed
215-XXX-XXX
CD-ROM Drive error
1. CD-ROM Drive Cable
2. Check power supply voltages
3. CD-ROM drive
4. System board
217-000-XXX
No action
Hard Disk Drive Test Passed
217-25X-XXX
217-26X-XXX
Hard Disk Drive (IDE) error
1. Hard Disk Drive Cable
2. Check power supply voltages
3. Reseat the hard disk drive cable
4. Hard Disk drive (IDE)
5. System board
217-28X-XXX
217-29X-XXX
Hard Disk Drive (SCSI) error
1. Hard Disk Drive Cable
2. Check power supply voltages
3. Reseat the hard disk drive cable
4. Hard Disk drive (SCSI)
5. SCSI adapter card
6. System board
220-000-XXX
No action
Hi-Capacity Cartridge Drive Test Passed
220-XXX-XXX
Hi-Capacity Cartridge Drive error
1. Remove the Hi-Capacity Cartridge
Drive and re-test the system
301-XXX-XXX
Keyboard error
1. Keyboard
2. Check and test mouse
3. System board
301-000-XXX
No action
Keyboard Test Passed
302-000-XXX
No action
Mouse Test Passed
302-XXX-XXX
Mouse error
1. Mouse
2. Check and test Keyboard
3. System board
303-000-XXX
No action
Joystick Test Passed
303-XXX-XXX
Joystick error
Remove the Joystick and re-test the system
No action
305-000-XXX
Monitor DDC Test Passed
305-250-XXX
Monitor DDC self test failure
1. Run Setup to enable DDC
2. Cable
3. Monitor
4. Video card
5. System board
80 Hardware Maintenance Manual
Diagnostic Error Code
FRU/Action
No action
415-000-XXX
Modem Test Passed
415-XXX-XXX
Remove the Modem and re-test the system
Modem error
Chapter 7. Symptom-to-FRU Index 81
Beep symptoms
Beep symptoms are short tones or a series of short tones separated by pauses
(intervals without sound). See the following examples.
Beeps
1-2-X
Description
v One beep
v A pause (or break)
v Two beeps
v A pause (or break)
v Any number of breaks
4
Four continuous beeps
Use the following table to diagnose beep symptoms.
Beep Symptom
FRU/Action
1-1-3
1. Run Setup
CMOS read-write error
2. System Board
1-2-2-3
System board
ROM BIOS check error
1-2-1
System board
Programmable Interval Timer failed
1-2-2 DMA Initialization failed
System board
System board
1-2-3 DMA page register write/read failed
1-2-4 RAM refresh verification failed
1. Memory module
2. System Board
1-3-3-1 1st 64K RAM test failed
1. Memory module
2. System Board
1-3-2 1st 64K RAM parity test failed
1. Memory module
2. Processor
3. System Board
2-2-3-1
System board
Interrupt vector loading test failed
2-1-1 Secondary DMA register failed
System board
System board
2-1-2
Primary DMA register failed
2-1-3 Primary interrupt mask register failed System board
2-1-4 Secondary interrupt mask register
System board
failed
2-2-1 Interrupt vector loading failed
System board
1-3-1-3 Keyboard controller failed
1. System Board
2. Keyboard
2-2-3
1. Battery
CMOS power failure and checksum checks
failed
2. System Board
82 Hardware Maintenance Manual
Beep Symptom
FRU/Action
2-2-4 CMOS configuration info validation
failed
1. Battery
2. System Board
2-3-1 Screen initialization failed
1. Jumper on J28
2. System Board
2-3-2 Screen memory failed
2-3-3 Screen retrace failed
1-2 Search for video ROM failed
All other beep code sequences
Continuous beep
System board
System board
System board
System board
System Board
Repeating short beeps
1. Keyboard stuck key
2. Keyboard Cable
3. System Board
Chapter 7. Symptom-to-FRU Index 83
POST error codes
Each time you power-on the system, it performs a series of tests that check the
operation of the system and some options. This series of tests is called the
Power-On Self-Test, or POST. POST does the following operations.
v Checks some basic system-board operations
v Checks the memory operation
v Starts the video operation
v Verifies that the diskette drive is working
v Verifies that the hard disk drive is working
If the POST finishes without detecting any problems, a single beep sounds and the
first screen of the operating system or application program appears.
If the POST detects a problem, an error message appears on the screen. A single
problem can cause several error messages to appear. When you correct the cause of
the first error message, the other error messages probably will not appear on the
screen the next time you turn on the system.
In the following index, X can represent any number.
POST Error Code
FRU/Action
162
Select the default settings in BIOS. See
Configuration error
164
1. Run the Extended Memory Diagnostic
Memory Size Error
tests
2. Replace memory modules
166
1. Perform a flash update to update the
Boot Block Check Sum Error
BIOS level
2. System board
167
1. Run Setup. Check Stepping level for the
BIOS level needed, then perform the
flash update.
No Processor BIOS update found
2. Replace the microprocessor
175 Primary Copy of Secure Data is
damaged
1. Run Setup and select default settings
2. System board
176 The System has been tampered with
1. Covers were removed from the computer
179 Boot Integrity Services Segment Error
1. Perform a flash update to update the
BIOS level
2. System board
1. Make sure Asset Care and Asset ID™ are
184
Asset Control Antenna not detected
enabled in Configuration/Setup
2. RFID Antenna
3. Replace system board
186 Security Hardware Control Logic Error
If problem persists, replace the system board
If problem persists, replace the system board
190
System Security: Invalid Remote Change
Requested
Chapter 7. Symptom-to-FRU Index 85
POST Error Code
FRU/Action
191 System Security: Embedded Security
If problem persists, replace the system board
hardware Reset
192 System Security: Embedded Security
hardware tamper detected
If problem persists, replace the system board
If problem persists, replace the system board
If problem persists, replace the system board
If problem persists, replace the system board
If problem persists, replace the system board
193 System Security: Embedded Security
hardware Removed
194 System Security: Asset ID Antenna has
been Removed
195 System Security: Asset ID Antenna has
been installed
196 System Tampered Cleared
201
1. Run Enhanced Diagnostics Memory Test
2. Memory module
Memory error
3. System board
210
1. Check for stuck keys
Keyboard stuck key error
2. Replace the keyboard
211
1. Make sure keyboard is connected
Keyboard error
correctly
2. Check for stuck keys
3. Replace the keyboard
212
1. Replace the keyboard
Keyboard controller error
2. If problem persists, replace the system
board
250
1. Replace the battery and run Setup
Battery is dead
2. If problem persists, replace the system
board
270
1. Run Setup and set date and time
Real time clock error
2. If problem persists, replace the system
board
271
1. Run Setup and set date and time
Date and time out of range
2. If problem persists, replace the system
board
662 Configuration Change has occurred
Diskette drive configuration error or wrong
diskette drive type; run Setup.
1762
1. Run Setup and verify hard disk drive
Configuration Change has occurred
settings.
2. Run hard disk drive diagnostics.
3. Replace hard disk drive
1800 PCI/PnP Error! No Hardware Interrupt
Available
1. Run Setup and verify PCI/ISA
configuration settings.
2. Run diagnostics.
3. Replace PCI Adapter
86 Hardware Maintenance Manual
POST Error Code
FRU/Action
1801 PCI/PnP Error! No Space Available to
Shadow ROM
1. Run Setup and verify PCI/ISA
configuration settings.
2. Run diagnostics.
3. Replace PCI Adapter
1802 PCI/PnP Error! Not Enough I/O Space
Available
1. Run Setup and verify PCI/ISA
configuration settings.
2. Run diagnostics.
3. Replace PCI Adapter
1803 PCI/PnP Error! Not Enough Memory
Space Available
1. Run Setup and verify PCI/ISA
configuration settings.
2. Run diagnostics.
3. Replace PCI Adapter
1804 PCI/PnP Error! Not Enough Real
Memory Space Available
1. Run Setup and verify PCI/ISA
configuration settings.
2. Run diagnostics.
3. Replace PCI Adapter
1805 PCI/PnP Error! Adapter ROM
Checksum Error
1. Run Setup and verify PCI/ISA
configuration settings.
2. Run diagnostics.
3. Replace PCI Adapter
1962
Press F1 to repeat boot sequence.
No operating system found
5962
1. Run Setup.
An IDE device (other than hard drive)
configuration error
2. CD-ROM Drive
3. CD-ROM Adapter
4. Zip or other ATAPI device
5. Replace system Board
6. Replace riser card if applicable
8603, 8604 Pointing Device Error
1. Replace pointing device
(mouse)
2. if problem persists, replace the system
board
Chapter 7. Symptom-to-FRU Index 87
Miscellaneous error messages
Message/Symptom
FRU/Action
CMOS Backup Battery inaccurate
2. System Board
Changing colors
Display/Monitor
1. Power Switch
2. System Board
3. Riser card
Computer will not RPL from server
1. Ensure that network is in startup
sequence as first device or first device
after diskette
2. Ensure that network adapter is enabled
for RPL
3. Network adapter (Advise network
administrator of new MAC address)
Computer will not perform a Wake On
1. Check power supply and signal cable
LAN® (if applicable)
connections to network adapter
2. Ensure that the operating system settings
are set to enable Wake on LAN®
3. Ensure Wake On LAN feature is enabled
in Setup/Configuration (see “Starting the
4. Ensure network administrator is using
correct MAC address
5. Ensure no interrupt or I/O address
conflicts
6. Network adapter (advise network
administrator of new MAC address)
Dead computer. See “Power Supply Errors”
1. Power Supply
2. System Board
3. Riser card
Diskette drive in-use light remains on or
does not light when drive is active.
1. Diskette Drive
2. System Board
3. Diskette Drive Cable
4. Riser card
Flashing cursor with an otherwise blank
display.
1. System Board
2. Primary Hard Disk Drive
3. Hard Disk Drive Cable
4. Riser card
Incorrect memory size during POST
1. Run the Memory tests
2. Memory Module
3. System Board
88 Hardware Maintenance Manual
Message/Symptom
FRU/Action
″Insert a Diskette″ icon appears with a
known-good diagnostics diskette in the first
3.5-inch diskette drive.
1. System Board
2. Diskette Drive Cable
3. Riser card
4. Network Adapter
Intensity or color varies from left to right of
characters and color bars
1. Display
2. System Board
No power or fan not running
Non-system disk or disk error-type message
with a known-good diagnostic diskette.
1. Diskette Drive
2. System Board
3. Diskette Drive Cable
4. Riser card
Other display symptoms not listed above
(including blank or illegible display)
1. Display
2. System Board
Power-on indicator or hard disk drive in-use
light not on, but computer works correctly
1. Power Supply
2. System Board
3. LED Cables
Printer problems
1. Printer
Program loads from the hard disk with a
known-good diagnostics diskette in the first
3.5-inch diskette drive
1. Run Setup
2. Diskette Drive
3. Diskette Drive Cable
4. System Board
5. Riser card
6. Power Supply
RPL computer cannot access programs from
its own hard disk.
1. If network administrator is using
LCCM Hybrid RPL, check startup
sequence:
a. First device - network
b. Second device - hard disk
2. Hard disk drive
RPL computer does not RPL from server
1. Check startup sequence
2. Check the network adapter LED status
Serial or parallel port device failure (system
board port)
1. External Device Self-Test OK?
2. External Device
3. Cable
4. System Board
Serial or parallel port device failure (adapter
port)
1. External Device Self-Test OK?
2. External Device
3. Cable
4. Alternate Adapter
5. System Board
Chapter 7. Symptom-to-FRU Index 89
Message/Symptom
FRU/Action
Some or all keys on the keyboard do not
work
1. Keyboard
2. Keyboard Cable
3. System Board
Undetermined problems
voltages are correct, return here and continue with the following steps.
1. Power-off the computer.
2. Remove or disconnect the following components (if installed) one at a time.
a. External devices (modem, printer, or mouse)
b. Any adapters
c. Riser card
d. Memory modules
e. Extended video memory
f. External Cache
g. External Cache RAM
h. Hard disk drive
i. Diskette drive
3. Power-on the computer to re-test the system.
4. Repeat steps 1 through 3 until you find the failing device or adapter.
If all devices and adapters have been removed, and the problem continues, replace
the system board.
90 Hardware Maintenance Manual
Chapter 8. Replacing FRUs (Types 8126, 8174, 8175, and 8176)
Important
Before you replace any FRU, read Chapter 2, “Safety information,” on page 5.
These precautions and guidelines will help you work safely.
FRU replacements are to be done by trained service technicians only.
This chapter does not contain a remove and replace procedure for all FRUs. Only
the major FRUs are documented.
Locating connectors on the front
The following illustration shows the locations of the USB connectors on the front of
the computer.
ꢀ1ꢁMicrophone connector
ꢀ2ꢁHeadphone connector
ꢀ3ꢁUSB connector
ꢀ4ꢁUSB connector
© Lenovo 2005. Portions © IBM Corp. 2005.
91
Locating the connectors on the rear
The following illustration shows the locations of the connectors on the rear of the
computer.
ꢀ1ꢁ
ꢀ2ꢁ
ꢀ3ꢁ
Power connector ꢀ8ꢁ
Mouse connector ꢀ9ꢁ
USB connectors
Ethernet connector
Microphone connector
Keyboard
connector
ꢀ10ꢁ
ꢀ4ꢁ
ꢀ5ꢁ
ꢀ6ꢁ
USB connectors ꢀ11ꢁ
Serial connector ꢀ12ꢁ
Audio line out connector
Audio line in connector
AGP slot (some models)
Parallel
ꢀ13ꢁ
connector
VGA Monitor
connector
ꢀ7ꢁ
ꢀ14ꢁ
PCI slots (In some models, other devices, such as a
modem, might be installed here.)
Removing the cover
Important
discharge-sensitive devices” on page 8 before removing the cover.
1. Shut down your operating system, remove any media (diskettes, CDs, or tapes)
from the drives, and turn off all attached devices and the computer.
2. Unplug all power cords from electrical outlets.
3. Disconnect all cables attached to the computer. This includes power cords,
input/output (I/O) cables, and any other cables that are connected to the
computer.
4. Remove the two screws at the rear and slide the cover to the rear to remove.
92 Hardware Maintenance Manual
Chapter 8. Replacing FRUs (Types 8126, 8174, 8175, and 8176) 93
Identifying parts on the system board
ꢀ1ꢁ
ꢀ2ꢁ
ꢀ3ꢁ
ꢀ4ꢁ
ꢀ5ꢁ
ꢀ6ꢁ
ꢀ7ꢁ
ꢀ8ꢁ
Microprocessor
ꢀ9ꢁ
Secondary IDE connector
SATA1 connector
SATA2 connector
Power switch/LEDs connector
Clear CMOS/Recovery jumper
Battery
Front panel audio connector
PCI slots
DIMM connector 1
DIMM connector 2
DIMM connector 3
DIMM connector 4
Power connector
Diskette drive
ꢀ10ꢁ
ꢀ11ꢁ
ꢀ12ꢁ
ꢀ13ꢁ
ꢀ14ꢁ
ꢀ15ꢁ
ꢀ16ꢁ
ꢀ17ꢁ
Primary IDE connector
AGP slot (some models)
Chapter 8. Replacing FRUs (Types 8126, 8174, 8175, and 8176) 95
Removing and replacing memory
3. Open the retaining clips and remove the failing DIMM.
4. Make sure the notch ꢀ1ꢁ on the new DIMM is aligned correctly with the
connector key ꢀ2ꢁ on the socket. Insert the DIMM straight down into the
connector until it snaps into position and the retaining clips are closed.
Removing and replacing a PCI adapter
2. Remove the screw securing the adapter.
3. Remove the failing adapter.
4. Remove the new adapter from its static-protective package.
5. Install the new adapter into the appropriate slot on the system board.
96 Hardware Maintenance Manual
6. Secure the adapter with the screw as shown.
Removing and replacing the battery
3. If necessary, remove any adapters that impede access to the battery. See
“Removing and replacing a PCI adapter” on page 96 for more information.
4. Remove the old battery.
5. Install the new battery.
6. Replace any adapters that were removed to gain access to the battery.
Note: Use the Setup Utility program to set the date and time and any
passwords. See Chapter 6, “Using the Setup Utility,” on page 55.
Chapter 8. Replacing FRUs (Types 8126, 8174, 8175, and 8176) 97
Removing and replacing the power supply
Attention
Never remove the cover on a power supply or any part that has the
following label attached.
Hazardous voltage, current, and energy levels are present inside any
component that has this label attached. There are no servicable parts inside
these components.
2. Disconnect all power supply cables from the drives.
4. Support the power supply and remove the four screws that hold the power
supply in place.
5. Remove the power supply.
6. Install the new power supply and insert the four screws that hold the power
supply in place.
7. Reconnect all power supply cables to the system board and the drives. See
98 Hardware Maintenance Manual
Removing and replacing the system board
3. Remove any air baffles or ducts.
4. Carefully take note of the location of all cable connections on the system
board. It will be necessary to reconnect them properly when installing a new
system board. See “Identifying parts on the system board” on page 95.
5. Disconnect all cables connected to the system board.
6. Remove the screws that secure the system board in place and remove the
system board.
7. Take note of the location of the DIMMs and remove them from the failing
system board and install them on the new system board in the same location
as they were on the failing system board. See “Removing and replacing
8. Remove the heat sink and microprocessor from the failing system board and
install them on the new system board. See “Removing and replacing the
microprocessor.” Continue at the next step after installing the heat sink and
microprocessor on the new system board.
9. Install the new system board and insert the screws.
10. Reconnect all cables to the system board.
11. Replace any air baffles or ducts.
Removing and replacing the microprocessor
2. Remove any air baffles or ducts that cover the microprocessor.
3. Disconnect the heat sink fan cable from the system board. Refer to
Chapter 8. Replacing FRUs (Types 8126, 8174, 8175, and 8176) 99
4. Loosen the two captured screws ꢀ3ꢁ holding the fan and heat sink ꢀ1ꢁ in
place, and pivot them to the side.
5. To remove the fan and heat sink from the microprocessor ꢀ2ꢁ, gently twist the
fan and heat sink to break the seal formed by the thermal grease and remove.
Note: If the thermal grease seal cannot be broken, you may want to start up
the system to heat the processor and loosen the thermal grease.
6. Place the heat sink on a clean work surface.
7. Take notice of the orientation of the beveled corner on the microprocessor.
This is important when reinstalling the microprocessor on the system board.
8. Release the microprocessor from the system board by pulling outward and
lifting the small handle on the microprocessor socket to its maximum vertical
position. Carefully lift the microprocessor off the socket.
9. Make sure that the microprocessor socket handle is fully in the vertical
position. Otherwise the microprocessor pins might be damaged when
installing the microprocessor.
10. Position the microprocessor so that the pins are aligned with the socket and
with the beveled corner in the correct orientation.
11. Lower the handle until it is fully in the down position and locked into the
socket. This secures the microprocessor in the socket.
12. Remove the cleaning pad from its package and use the cleaning pad to wipe
the thermal grease from the bottom of the heat sink.
Notes:
a. The cleaning pad and thermal grease are separate FRUs and are not
included with the system board or microprocessor FRUs. These must be
ordered separately and shipped along with the FRUs being replaced.
b. Be sure that all of the thermal grease is removed.
Note: 0.01ML is one tick mark on the syringe. If the grease is properly
applied, approximately half (0.22ML) of the grease will remain in the
syringe.
13. Use the thermal grease syringe to place 16 uniformly spaced dots of 0.01ML
each on the top of the microprocessor.
100 Hardware Maintenance Manual
0.01 mL of
thermal grease
Microprocessor
14. Place the fan and heat sink into position on the microprocessor.
15. When tightening the screws that clamp the heat sink, do not overtighten.
Tighten the clamp screws evenly by tightening one side some and then the
other until they are both snug.
16. Reconnect the fan to the system board connector.
17. If you are replacing a failing system board, go back to the system board
procedure. Otherwise, go to “Closing the cover and connecting cables” on
Removing and replacing drives
2. If you are removing the hard disk drive or diskette drive, remove the front
bezel by releasing the four plastic tabs inside the chassis and pressing down
on the top of the bezel.
Chapter 8. Replacing FRUs (Types 8126, 8174, 8175, and 8176) 101
3. Disconnect the signal and power cables from the failing drive.
Note: Take note of the location of any cables you disconnect. You might have
to disconnect cables to other drives to gain access to the drive you are
removing.
4. Remove the screws that secure the drive being removed.
Note: The hard disk drive has four screws; two at the side of the drive and
two on the bottom.
5. If removing the hard disk drive, remove the cover on the front of the drive.
6. Slide the drive out the front of the computer.
102 Hardware Maintenance Manual
Note: This illustration shows the hard disk drive being removed. All drives
are removed in the same manner. However, it is only necessary to
remove the front bezel when removing the hard disk drive or diskette
drive.
7. Make sure the drive that you are installing is set correctly as either a master
or a slave device. Jumper the new drive the same as the drive being replaced.
Note: If you are installing a serial ATA drive, no master/slave jumpering is
necessary.
Refer to the documentation that comes with your drive for master/slave
jumper information.
8. Install the new drive into the bay. Align the screw holes and install the screws
to secure the drive.
Chapter 8. Replacing FRUs (Types 8126, 8174, 8175, and 8176) 103
Note: This illustration shows a CD drive installation. The hard disk drive and
diskette drive is installed in the same manner except that the front
bezel is not in place.
9. If installing the hard disk drive, replace the cover on the front of the drive.
10. If the front bezel was removed, replace it by aligning the four plastic tabs and
pressing the bezel into position.
11. Reconnect the signal and power cables to the drive.
Closing the cover and connecting cables
After replacing FRUs, you need to install any removed parts, replace the cover, and
reconnect any cables, including telephone lines and power cords. Also, depending
on the FRU that is replaced, you might need to confirm the updated information in
the Setup Utility program.
1. Ensure that all components have been reassembled correctly and that no tools
or loose screws are left inside the computer.
2. Clear any cables that might impede the replacement of the cover.
3. Position the cover on the chassis so that the guides on the top and bottom of
the cover engage the chassis and push the cover to the closed position. Insert
the screws that secure the cover.
4. Reconnect the external cables and power cords to the computer.
Note: When the power cord is first plugged in, the computer might appear to turn
on for a few seconds and then turn off. This is a normal sequence to enable
the computer to initialize.
104 Hardware Maintenance Manual
Chapter 9. Replacing FRUs (Types 8149, 8177, and 8178)
Important
Before you replace any FRU, read Chapter 2, “Safety information,” on page 5.
These precautions and guidelines will help you work safely.
FRU replacements are to be done by trained service technicians only.
This chapter does not contain a remove and replace procedure for all FRUs. Only
the major FRUs are documented.
Locating connectors on the front
The following illustration shows the locations of the USB connectors on the front of
the computer.
ꢀ1ꢁUSB connector
ꢀ2ꢁUSB connector
© Lenovo 2005. Portions © IBM Corp. 2005.
105
Locating connectors on the rear
ꢀ1ꢁ
ꢀ2ꢁ
ꢀ3ꢁ
ꢀ4ꢁ
ꢀ5ꢁ
ꢀ6ꢁ
ꢀ7ꢁ
Power connector
Mouse connector
Parallel connector
Ethernet connector
Audio line in connector
PCI slots
ꢀ8ꢁ
ꢀ9ꢁ
Audio line out connector
Microphone connector
USB connectors
VGA monitor connector
Serial connector
ꢀ10ꢁ
ꢀ11ꢁ
ꢀ12ꢁ
ꢀ13ꢁ
ꢀ14ꢁ
USB connectors
Keyboard connector
AGP slot (some models)
Removing the cover
Important
discharge-sensitive devices” on page 8 before removing the cover.
1. Shut down your operating system, remove any media (diskettes, CDs, or tapes)
from the drives, and turn off all attached devices and the computer.
2. Unplug all power cords from electrical outlets.
3. Disconnect all cables attached to the computer. This includes power cords,
input/output (I/O) cables, and any other cables that are connected to the
computer.
4. Press the buttons on the sides of the computer and pivot the rear of the cover
up and off of the computer.
106 Hardware Maintenance Manual
Locating components
ꢀ1ꢁ
ꢀ2ꢁ
ꢀ3ꢁ
ꢀ4ꢁ
ꢀ5ꢁ
ꢀ6ꢁ
CD drive or DVD drive
ꢀ7ꢁ
ꢀ8ꢁ
ꢀ9ꢁ
ꢀ10ꢁ
ꢀ11ꢁ
DIMMs
USB connector
USB connector
Optional drive bay
Hard disk drive
Diskette drive
Microprocessor and heat sink
AGP slot (some models)
Battery
PCI slots
Chapter 9. Replacing FRUs (Types 8149, 8177, and 8178) 107
Identifying parts on the system board
ꢀ1ꢁ
ꢀ2ꢁ
ꢀ3ꢁ
ꢀ4ꢁ
ꢀ5ꢁ
ꢀ6ꢁ
ꢀ7ꢁ
ꢀ8ꢁ
Microprocessor
ꢀ9ꢁ
Secondary IDE connector
SATA1 connector
SATA2 connector
Power switch/LEDs connector
Clear CMOS/Recovery jumper
Battery
Front panel audio connector
PCI slots
DIMM connector 1
DIMM connector 2
DIMM connector 3
DIMM connector 4
Power connector
Diskette drive
ꢀ10ꢁ
ꢀ11ꢁ
ꢀ12ꢁ
ꢀ13ꢁ
ꢀ14ꢁ
ꢀ15ꢁ
ꢀ16ꢁ
ꢀ17ꢁ
Primary IDE connector
AGP slot (some models)
108 Hardware Maintenance Manual
Removing and replacing memory
3. Open the retaining clips and remove the failing DIMM.
4. Make sure the notch ꢀ1ꢁ on the new DIMM is aligned correctly with the
connector key ꢀ2ꢁ on the socket. Insert the DIMM straight down into the
connector until it snaps into position and the retaining clips are closed.
Chapter 9. Replacing FRUs (Types 8149, 8177, and 8178) 109
Removing and replacing a PCI adapter
2. Open and remove the adapter-slot-cover latch and remove the failing adapter.
3. Remove the new adapter from its static-protective package.
4. Install the new adapter into the appropriate slot on the system board.
5. Install and close the adapter-slot-cover latch.
Removing and replacing the battery
3. If necessary, remove any adapters that impede access to the battery. See
“Removing and replacing a PCI adapter” for more information.
4. Remove the old battery.
110 Hardware Maintenance Manual
5. Install the new battery.
6. Replace any adapters that were removed to gain access to the battery.
Note: Use the Setup Utility program to set the date and time and any
passwords. See Chapter 6, “Using the Setup Utility,” on page 55.
Removing and replacing the power supply
Attention
Never remove the cover on a power supply or any part that has the
following label attached.
Hazardous voltage, current, and energy levels are present inside any
component that has this label attached. There are no servicable parts inside
these components.
2. Disconnect all power supply cables from the system board and the drives. See
3. Remove the four screws that hold the power supply in place.
4. Lift the power supply out.
Chapter 9. Replacing FRUs (Types 8149, 8177, and 8178) 111
5. Install the new power supply and insert the four screws that hold the power
supply in place.
6. Reconnect all power supply cables to the system board and the drives. See
Removing and replacing the system board
3. Carefully take note of the location of all cable connections on the system
board. It will be necessary to reconnect them properly when installing a new
system board. See “Identifying parts on the system board” on page 108.
4. Disconnect all cables connected to the system board.
5. Remove the screws that secure the system board in place and remove the
system board.
6. Take note of the location of the DIMMs and remove them from the failing
system board and install them on the new system board in the same location
as they were on the failing system board. See “Removing and replacing
7. Remove the heat sink and microprocessor from the failing system board and
install them on the new system board. See “Removing and replacing the
112 Hardware Maintenance Manual
microprocessor.” Continue to the next step after installing the heat sink and
microprocessor on the new system board.
8. Install the new system board into the chassis and insert the screws.
Removing and replacing the microprocessor
1. Turn off the computer and peripheral devices and disconnect all external
cables and power cords; then, remove the cover. See “Removing the cover” on
2. Remove any air baffles or ducts that cover the microprocessor.
3. Disconnect the heat sink fan cable from the system board. Refer to
4. Loosen the two captured screws ꢀ3ꢁ holding the fan and heat sink in place,
and pivot them to the side.
5. To remove the fan and heat sink ꢀ1ꢁ from the microprocessor ꢀ2ꢁ, gently twist
the fan and heat sink to break the seal formed by the thermal grease and
remove.
Note: If the thermal grease seal cannot be broken, you may want to start up
the system to heat the processor and loosen the thermal grease.
6. Place the heat sink on a clean work surface.
7. Take notice of the orientation of the beveled corner on the microprocessor.
This is important when reinstalling the microprocessor on the system board.
8. Release the microprocessor from the system board by pulling outward and
lifting the small handle on the microprocessor socket to its maximum vertical
position. Carefully lift the microprocessor off the socket.
9. Make sure that the microprocessor socket handle is fully in the vertical
position. Otherwise the microprocessor pins might be damaged when
installing the microprocessor.
10. Position the microprocessor so that the pins are aligned with the socket and
with the beveled corner in the correct orientation.
Chapter 9. Replacing FRUs (Types 8149, 8177, and 8178) 113
11. Lower the handle until it is fully in the down position and locked into the
socket. This secures the microprocessor in the socket.
12. Remove the cleaning pad from its package and use the cleaning pad to wipe
the thermal grease from the bottom of the heat sink.
Notes:
a. The cleaning pad and thermal grease are separate FRUs and are not
included with the system board or microprocessor FRUs. These must be
ordered separately and shipped along with the FRUs being replaced.
b. Be sure that all of the thermal grease is removed.
Note: 0.01ML is one tick mark on the syringe. If the grease is properly
applied, approximately half (0.22ML) of the grease will remain in the
syringe.
13. Use the thermal grease syringe to place 16 uniformly spaced dots of 0.01ML
each on the top of the microprocessor.
0.01 mL of
thermal grease
Microprocessor
14. Place the fan and heat sink into position on the microprocessor.
15. When tightening the screws that clamp the heat sink, do not overtighten.
Tighten the clamp screws evenly by tightening one side some and then the
other until they are both snug.
16. Reconnect the fan to the system board connector.
17. Replace any air baffles or ducts that were removed.
Removing and replacing drives
2. Pivot the drive-bay latch handle toward the front of the computer and then
pivot the appropriate drive-bay cage upward, as shown, until latched in the
upright position.
Notes:
a. Both drive-bay cages pivot in the same manner.
b. You can lift the drive-bay cages out of the chassis to make it easier to
remove and install the drives.
c. Take note of the location of any cables you disconnect. You might have to
disconnect cables to other drives to gain access to the drive you are
removing.
114 Hardware Maintenance Manual
3. Disconnect the signal cable and power supply cable from the drive being
replaced.
4. Remove any screws that secure the drive. Not all drives have screws.
5. Make sure the drive that you are installing is set correctly as either a master or
a slave device. Jumper the new drive the same as the drive being replaced.
Note: If you are installing a serial ATA drive, no master/slave jumpering is
necessary.
Refer to the documentation that comes with your drive for master/slave
jumper information.
6. Install the drive into the bay as shown.
Chapter 9. Replacing FRUs (Types 8149, 8177, and 8178) 115
7. Secure the new drive (if necessary) with the screws that were removed.
8. If necessary, place the drive-bay cages back into the chassis.
Installing the cover and connecting cables
After replacing FRUs, you need to install any removed parts, replace the cover, and
reconnect cables, including telephone lines and power cords. Also, depending on
the option that is installed, you might need to confirm the updated information in
the Setup Utility program.
1. Ensure that all components have been reassembled correctly and that no tools
or loose screws are left inside the computer.
2. Clear any cables that might impede the replacement of the cover.
3. Lower the drive-bay cages to the normal position.
4. Position the cover over the chassis and pivot it down over the computer until it
snaps into place.
116 Hardware Maintenance Manual
5. Reconnect the external cables and power cords to the computer.
Chapter 9. Replacing FRUs (Types 8149, 8177, and 8178) 117
118 Hardware Maintenance Manual
Chapter 10. Replacing FRUs (Types 8084, 8085, 8147, 8148,
and 8179
Important:
Before you replace any FRU, read Chapter 2, “Safety information,” on page 5.
These precautions and guidelines will help you work safely.
FRU replacements are to be done by trained service technicians only.
This chapter does not contain a remove and replace procedure for all FRUs. Only
the major FRUs are documented.
© Lenovo 2005. Portions © IBM Corp. 2005.
119
Locating the connectors on the rear
ꢀ1ꢁ
ꢀ2ꢁ
ꢀ3ꢁ
ꢀ4ꢁ
ꢀ5ꢁ
ꢀ6ꢁ
ꢀ7ꢁ
Power connector
Mouse connector
Keyboard connector
USB connectors
Serial connector
Parallel connector
VGA monitor connector
ꢀ8ꢁ
ꢀ9ꢁ
USB connectors
Ethernet connector
Microphone connector
Audio line out connector
Audio line in connector
AGP slot (some models)
PCI slots
ꢀ10ꢁ
ꢀ11ꢁ
ꢀ12ꢁ
ꢀ13ꢁ
ꢀ14ꢁ
Removing the cover
Important
discharge-sensitive devices” on page 8 before removing the cover.
1. Shut down your operating system, remove any media (diskettes, CDs, or tapes)
from the drives, and turn off all attached devices and the computer.
2. Unplug all power cords from electrical outlets.
3. Disconnect all cables attached to the computer. This includes power cords,
input/output (I/O) cables, and any other cables that are connected to the
computer.
4. Press the cover-release button and slide the cover to the rear to remove.
Chapter 10. Replacing FRUs (Types 8084, 8085, 8147, 8148, and 8179 121
122 Hardware Maintenance Manual
Identifying parts on the system board
ꢀ1ꢁ
ꢀ2ꢁ
ꢀ3ꢁ
ꢀ4ꢁ
ꢀ5ꢁ
ꢀ6ꢁ
ꢀ7ꢁ
ꢀ8ꢁ
Microprocessor
ꢀ9ꢁ
Secondary IDE connector
SATA1 connector
SATA2 connector
Power switch/LEDs connector
Clear CMOS/Recovery jumper
Battery
Front panel audio connector
PCI slots
DIMM connector 1
DIMM connector 2
DIMM connector 3
DIMM connector 4
Power connector
Diskette drive
ꢀ10ꢁ
ꢀ11ꢁ
ꢀ12ꢁ
ꢀ13ꢁ
ꢀ14ꢁ
ꢀ15ꢁ
ꢀ16ꢁ
ꢀ17ꢁ
Primary IDE connector
AGP slot (some models)
124 Hardware Maintenance Manual
Removing and replacing memory
3. Open the retaining clips and remove the failing DIMM.
4. Make sure the notch ꢀ1ꢁ on the new DIMM is aligned correctly with the
connector key ꢀ2ꢁ on the socket. Insert the DIMM straight down into the
connector until it snaps into position and the retaining clips are closed.
Removing and replacing a PCI adapter
Chapter 10. Replacing FRUs (Types 8084, 8085, 8147, 8148, and 8179 125
2. Open the adapter-slot-latch securing the adapter and remove the failing
adapter.
3. Remove the new adapter from its static-protective package.
4. Install the new adapter into the appropriate slot on the system board and
secure the adapter with the adapter-slot-latch.
126 Hardware Maintenance Manual
Removing and replacing the battery
3. If necessary, remove any adapters that impede access to the battery. See
“Removing and replacing a PCI adapter” on page 125 for more information.
4. Remove the old battery.
5. Install the new battery.
6. Replace any adapters that were removed to gain access to the battery.
Note: Use the Setup Utility program to set the date and time and any
passwords. See Chapter 6, “Using the Setup Utility,” on page 55.
Removing and replacing the power supply
Attention
Never remove the cover on a power supply or any part that has the
following label attached.
Hazardous voltage, current, and energy levels are present inside any
component that has this label attached. There are no servicable parts inside
these components.
2. Disconnect all power supply cables from the drives.
4. Support the power supply and remove the four screws that hold the power
supply in place.
5. Remove the power supply.
Chapter 10. Replacing FRUs (Types 8084, 8085, 8147, 8148, and 8179 127
6. Install the new power supply and insert the four screws that hold the power
supply in place.
7. Reconnect all power supply cables to the system board and the drives. See
Removing and replacing the system board
3. Carefully take note of the location of all cable connections on the system
board. It will be necessary to reconnect them properly when installing a new
system board. See “Identifying parts on the system board” on page 124.
4. Remove any air baffles or ducts.
5. Disconnect all cables connected to the system board.
6. Remove the screws that secure the system board in place and remove the
system board.
128 Hardware Maintenance Manual
7. Take note of the location of the DIMMs and remove them from the failing
system board and install them on the new system board in the same location
as they were on the failing system board. See “Removing and replacing
8. Remove the heat sink and microprocessor from the failing system board and
install them on the new system board. See “Removing and replacing the
microprocessor.” Continue at the next step after installing the heat sink and
microprocessor on the new system board.
9. Install the new system board and insert the screws.
10. Reconnect all cables to the system board.
11. Replace any air baffles or ducts.
Removing and replacing the microprocessor
2. Remove any air baffles or ducts that cover the microprocessor.
3. Disconnect the heat sink fan cable from the system board. Refer to
Chapter 10. Replacing FRUs (Types 8084, 8085, 8147, 8148, and 8179 129
4. Loosen the two captured screws ꢀ3ꢁ holding the fan and heat sink in place,
and pivot them to the side.
5. To remove the fan and heat sink ꢀ1ꢁ from the microprocessor ꢀ2ꢁ, gently twist
the fan and heat sink to break the seal formed by the thermal grease and
remove.
Note: If the thermal grease seal cannot be broken, you may want to start up
the system to heat the processor and loosen the thermal grease.
6. Place the heat sink on a clean work surface.
7. Take notice of the orientation of the beveled corner on the microprocessor.
This is important when reinstalling the microprocessor on the system board.
8. Release the microprocessor from the system board by pulling outward and
lifting the small handle on the microprocessor socket to its maximum vertical
position. Carefully lift the microprocessor off the socket.
9. Make sure that the microprocessor socket handle is fully in the vertical
position. Otherwise the microprocessor pins might be damaged when
installing the microprocessor.
10. Position the microprocessor so that the pins are aligned with the socket and
with the beveled corner in the correct orientation.
11. Lower the handle until it is fully in the down position and locked into the
socket. This secures the microprocessor in the socket.
12. Remove the cleaning pad from its package and use the cleaning pad to wipe
the thermal grease from the bottom of the heat sink.
Notes:
a. The cleaning pad and thermal grease are separate FRUs and are not
included with the system board or microprocessor FRUs. These must be
ordered separately and shipped along with the FRUs being replaced.
b. Be sure that all of the thermal grease is removed.
Note: 0.01ML is one tick mark on the syringe. If the grease is properly
applied, approximately half (0.22ML) of the grease will remain in the
syringe.
130 Hardware Maintenance Manual
13. Use the thermal grease syringe to place 16 uniformly spaced dots of 0.01ML
each on the top of the microprocessor.
0.01 mL of
thermal grease
Microprocessor
14. Place the fan and heat sink into position on the microprocessor.
15. When tightening the screws that clamp the heat sink, do not overtighten.
Tighten the clamp screws evenly by tightening one side some and then the
other until they are both snug.
16. Reconnect the fan to the system board connector.
17. Replace any air baffles or ducts.
Removing and replacing drives
2. If you are removing a drive from bay 1 or bay 2, skip the next step.
3. Remove the front bezel by pushing in on the blue plastic tab at the rear of the
chassis.
4. Disconnect the signal and power cables from the drive being removed.
Note: Take note of the location of any cables you disconnect. You might have
to disconnect cables to other drives to gain access to the drive you are
removing.
Chapter 10. Replacing FRUs (Types 8084, 8085, 8147, 8148, and 8179 131
5. For all drives except the hard disk drive, push in on the metal tab that secures
the drive being removed. The hard disk drive tray pivots out toward the front
of the computer for removal of the hard disk drive. See the following
illustrations.
For the hard disk drive, see the illustration below.
6. Slide the drive out the front of the computer.
7. Make sure the drive that you are installing is set correctly as either a master
or a slave device. Jumper the new drive the same as the drive being replaced.
Note: If you are installing a serial ATA drive, no master/slave jumpering is
necessary.
Refer to the documentation that comes with your drive for master/slave
jumper information.
8. Slide the drive into the appropriate bay.
9. Reconnect the signal and power cables to the new drive.
132 Hardware Maintenance Manual
10. For bay 5 (hard disk drive), pivot the drive cage to the closed position.
11. If the front bezel was removed, replace it by aligning and pressing the bezel
into position.
Closing the cover and connecting cables
After replacing FRUs, you need to install any removed parts, replace the cover, and
reconnect any cables, including telephone lines and power cords. Also, depending
on the FRU that is replaced, you might need to confirm the updated information in
the Setup Utility program.
1. Ensure that all components have been reassembled correctly and that no tools
or loose screws are left inside the computer.
2. Clear any cables that might impede the replacement of the cover.
3. Position the cover on the chassis so that the rail guides on the bottom of the
cover engage the rails and push the cover closed until it latches.
4. Reconnect the external cables and power cords to the computer.
Chapter 10. Replacing FRUs (Types 8084, 8085, 8147, 8148, and 8179 133
134 Hardware Maintenance Manual
Chapter 11. FRU lists
Note: A CRU (Customer Replaceable Unit) is identified by a single asterisk (*) or
two asterisks (**) in the CRU ID column. An N in the CRU ID Column
means that the part is not a CRU. A single asterisk (*) means that the part is
a Tier 1 CRU; two asterisks (**) mean that the part is a Tier 2 CRU.
Machine Type 8084
Item #
8084 FRUs
FRU#
CRU
**
ꢀ1ꢁ Side cover assembly (all models)
ꢀ2ꢁ ″L″ Cover assembly (all models)
ꢀ3ꢁ Front Bezel assembly (all models)
ꢀ4ꢁ Bezel trim/label kit (all models)
59P8547
59P8546
59P8544
49P1900
**
**
**
© Lenovo 2005. Portions © IBM Corp. 2005.
135
Item #
8084 FRUs
FRU#
CRU
ꢀ5ꢁ CD-ROM Drive 48X (Black) - w/o volume ctrl and headphone jack (models 17S
23S 1BS 1AU 11U 12G 21G 24U A3G B1G B2G D4G E3G 41U 15G 18G 1CG 1DC
1EC 1FU 26G 31U 31G 73G 75G 76G 77G 78G 79G 7AG 7DG B2S D4S A4J E6G
33G 51G 53U 7KG 7NG 7PG D7U EAS 2AU 36U 37S EBG 7UG 7VG)
40Y8801
*
ꢀ5ꢁ CD-ROM Drive 48X (Black) - w/o volume ctrl and headphone jack (models 17S
23S 1BS 1AU 11U 12G 21G 24U A3G B1G B2G D4G E3G 41U 15G 18G 1CG 1DC
1EC 1FU 26G 31U 31G 73G 75G 76G 77G 78G 79G 7AG 7DG B2S D4S A4J E6G
33G 51G 53U 7KG 7NG 7PG D7U EAS 2AU 36U 37S EBG 7UG 7VG)
40Y8805
40Y8807
40Y8813
40Y8929
40Y8811
*
*
*
*
*
ꢀ5ꢁ CD-ROM Drive 48X (Black) - w/o volume ctrl and headphone jack (models 17S
23S 1BS 1AU 11U 12G 21G 24U A3G B1G B2G D4G E3G 41U 15G 18G 1CG 1DC
1EC 1FU 26G 31U 31G 73G 75G 76G 77G 78G 79G 7AG 7DG B2S D4S A4J E6G
33G 51G 53U 7KG 7NG 7PG D7U EAS 2AU 36U 37S EBG 7UG 7VG)
ꢀ5ꢁ CD-ROM Drive 48X (Black) - w/o volume ctrl and headphone jack (models 17S
23S 1BS 1AU 11U 12G 21G 24U A3G B1G B2G D4G E3G 41U 15G 18G 1CG 1DC
1EC 1FU 26G 31U 31G 73G 75G 76G 77G 78G 79G 7AG 7DG B2S D4S A4J E6G
33G 51G 53U 7KG 7NG 7PG D7U EAS 2AU 36U 37S EBG 7UG 7VG)
ꢀ5ꢁ CD-ROM Drive 48X (Black) - w/o volume ctrl and headphone jack (models 17S
23S 1BS 1AU 11U 12G 21G 24U A3G B1G B2G D4G E3G 41U 15G 18G 1CG 1DC
1EC 1FU 26G 31U 31G 73G 75G 76G 77G 78G 79G 7AG 7DG B2S D4S A4J E6G
33G 51G 53U 7KG 7NG 7PG D7U EAS 2AU 36U 37S EBG 7UG 7VG)
ꢀ5ꢁ DVD-ROM Drive (16x\48x) (models 19G 22G 32G 72G 74G 7BG 7CG 7EG 7GG
7HG 7JG 52G 7QG 7RG 7SG 7TG)
ꢀ5ꢁ DVD-ROM/CD-RW Combo Drive (48x\32x\48x\16x) (models 1GU)
40Y8781
40Y8903
40Y9107
*
*
*
ꢀ5ꢁ DVD-ROM/CD-RW Combo Drive (48x\32x\48x\16x) (models 1GU)
ꢀ6ꢁ Diskette drive, 3.5 1.44MB (models 17S 23S CTO-U CTO-G 1BS 1AU 21G 24U 15G
18G 19G 22G 31U 31G 32G 73G 74G 7BG 7CG 7EG D1S A1U A1F A2U A2F D2U
D2F E1U E1F E2U E2F 11U 12G 13U 13F 14U 14F 25U 25F A3G B1G B2G D2U
D2F D3U D3F D4G E3G 41U 1CG 1DC 1EC 1FU 26G 27U 27F 72G 75G 76G 77G
78G 79G 7AG 7DG 1GU B2S B3U B3F B4U B4F D4S D5U D5F D6U D6F E4U E4F
E5U E5F 1HU 1HF 1JU 1JF 28U 28F 29U 29F 7GG 7HG 7JG A4J E6G 33G 34U 34F
35U 35F 51G 52G 53U 7KG 7NG 7PG 7QG D7U E8U E8F E9U E9F EAS 2AU 36U
37S EBG 7RG 7SG 7TG 7UG 7VG)
ꢀ6ꢁ Diskette drive, 3.5 1.44MB (optional to 76H4091) (models 17S 23S CTO-U CTO-G
1BS 1AU 21G 24U 15G 18G 19G 22G 31U 31G 32G 73G 74G 7BG 7CG 7EG D1S
A1U A1F A2U A2F D2U D2F E1U E1F E2U E2F 11U 12G 13U 13F 14U 14F 25U
25F A3G B1G B2G D2U D2F D3U D3F D4G E3G 41U 1CG 1DC 1EC 1FU 26G 27U
27F 72G 75G 76G 77G 78G 79G 7AG 7DG 1GU B2S B3U B3F B4U B4F D4S D5U
D5F D6U D6F E4U E4F E5U E5F 1HU 1HF 1JU 1JF 28U 28F 29U 29F 7GG 7HG
7JG A4J E6G 33G 34U 34F 35U 35F 51G 52G 53U 7KG 7NG 7PG 7QG D7U E8U
E8F E9U E9F EAS 2AU 36U 37S EBG 7RG 7SG 7TG 7UG 7VG)
40Y8899
40Y9105
*
*
ꢀ6ꢁ Diskette drive, 3.5 1.44MB (optional to 76H4091) (models 17S 23S CTO-U CTO-G
1BS 1AU 21G 24U 15G 18G 19G 22G 31U 31G 32G 73G 74G 7BG 7CG 7EG D1S
A1U A1F A2U A2F D2U D2F E1U E1F E2U E2F 11U 12G 13U 13F 14U 14F 25U
25F A3G B1G B2G D2U D2F D3U D3F D4G E3G 41U 1CG 1DC 1EC 1FU 26G 27U
27F 72G 75G 76G 77G 78G 79G 7AG 7DG 1GU B2S B3U B3F B4U B4F D4S D5U
D5F D6U D6F E4U E4F E5U E5F 1HU 1HF 1JU 1JF 28U 28F 29U 29F 7GG 7HG
7JG A4J E6G 33G 34U 34F 35U 35F 51G 52G 53U 7KG 7NG 7PG 7QG D7U E8U
E8F E9U E9F EAS 2AU 36U 37S EBG 7RG 7SG 7TG 7UG 7VG)
136 Hardware Maintenance Manual
Item #
8084 FRUs
FRU#
CRU
ꢀ7ꢁ Hard disk drive, 40GB EIDE (models D1S 1AU A1U A1F A2U A2F D2U D2F E1U
E1F E2U E2F 11U 12G 13U 13F 14U 14F 21G 24U 25U 25F A3G B1G B2G D2U D2F
D3U D3F D4G E3G 41U 15G 16G 18G 1CG 1DC 1EC 1FU 26G 27U 27F 31U 31G
73G 75G 76G 77G 78G 79G 7AG 7DG 1GU B2S B3U B3F B4U B4F D4S D5U D5F
D6U D6F E4U E4F E5U E5F 1HU 1HF 1JU 1JF 28U 28F 29U 29F A4J E6G 33G 34U
34F 35U 35F 51G 53U 7KG 7NG 7PG D7U E8U E8F E9U E9F EAS 2AU 36U EBG
7RG 7SG 7TG 7UG 7VG)
40Y8757
*
ꢀ7ꢁ Hard disk drive, 80GB EIDE (models17S 23S 1BS 19G 22G 32G 72G 74G 7BG 7CG
40Y8758
19R0703
*
7EG 7GG 7HG 7JG 52G 7QG 37S)
ꢀ8ꢁ System board, 10/100 E-net (models 17S 23S CTO-U CTO-G 1BS 1AU 21G 24U
15G 18G 19G 22G 31U 31G 32G 73G 74G 7BG 7CG 7EG C5U C6U C7U 1GU 7HG
7JG 34U 34F 35U 35F 52G 53U 7QG C8U 2AU 36U 37S 7UG 7VG)
**
ꢀ8ꢁ System board,(10/100 Enet) w/ video buffer -- optional to 19R0703 (models 17S
23S CTO-U CTO-G 1BS 1AU 21G 24U 15G 18G 19G 22G 31U 31G 32G 73G 74G
7BG 7CG 7EG C5U C6U C7U 1GU 7HG 7JG 34U 34F 35U 35F 52G 53U 7QG C8U
2AU 36U 37S 7UG 7VG)
39J7965
41D0948
19R0837
**
**
**
ꢀ8ꢁ System board,(10/100 Enet) w/ video buffer -- optional to 19R0703 (models 17S
23S CTO-U CTO-G 1BS 1AU 21G 24U 15G 18G 19G 22G 31U 31G 32G 73G 74G
7BG 7CG 7EG C5U C6U C7U 1GU 7HG 7JG 34U 34F 35U 35F 52G 53U 7QG C8U
2AU 36U 37S 7UG 7VG)
ꢀ8ꢁ System board, 10/100 E-net, no AGP (models D1S A1U A1F A2U A2F D2U D2F
E1U E1F E2U E2F 11U 12G 13U 13F 14U 14F 25U 25F A3G B1G B2G D2U D2F
D3U D3F D4G E3G 41U 16G 1CG 1DC 1EC 1FU 26G 27U 27F 72G 75G 76G 77G
78G 79G 7AG 7DG C1U C2U C3U C4U B2S B3U B3F B4U B4F D4S D5U D5F D6U
D6F E4U E4F E5U E5F 1HU 1HF 1JU 1JF 28U 28F 29U 29F 7GG A4J E6G 33G 51G
7KG 7NG 7PG D7U E8U E8F E9U E9F EAS EBG 7RG 7SG 7TG)
ꢀ8ꢁ System board, (10/100 Enet) w/ video buffer, no AGP -- optional to 19R0837
(models D1S A1U A1F A2U A2F D2U D2F E1U E1F E2U E2F 11U 12G 13U 13F
14U 14F 25U 25F A3G B1G B2G D2U D2F D3U D3F D4G E3G 41U 16G 1CG 1DC
1EC 1FU 26G 27U 27F 72G 75G 76G 77G 78G 79G 7AG 7DG C1U C2U C3U C4U
B2S B3U B3F B4U B4F D4S D5U D5F D6U D6F E4U E4F E5U E5F 1HU 1HF 1JU
1JF 28U 28F 29U 29F 7GG A4J E6G 33G 51G 7KG 7NG 7PG D7U E8U E8F E9U
E9F EAS EBG 7RG 7SG 7TG)
39J7966
**
**
ꢀ8ꢁ System board, (10/100 Enet) w/ video buffer, no AGP -- optional to 19R0837
(models D1S A1U A1F A2U A2F D2U D2F E1U E1F E2U E2F 11U 12G 13U 13F
14U 14F 25U 25F A3G B1G B2G D2U D2F D3U D3F D4G E3G 41U 16G 1CG 1DC
1EC 1FU 26G 27U 27F 72G 75G 76G 77G 78G 79G 7AG 7DG C1U C2U C3U C4U
B2S B3U B3F B4U B4F D4S D5U D5F D6U D6F E4U E4F E5U E5F 1HU 1HF 1JU
1JF 28U 28F 29U 29F 7GG A4J E6G 33G 51G 7KG 7NG 7PG D7U E8U E8F E9U
E9F EAS EBG 7RG 7SG 7TG)
41D0949
ꢀ9ꢁ 128 MB SDRAM (models D1S)
31P9120
31P9121
*
*
ꢀ9ꢁ 256 MB SDRAM (models A1U A1F A2U A2F D2U D2F E1U E1F E2U E2F 11U 12G
13U 13F 14U 14G 25U 25F A3G B1G B2G D2U D2F D3U D3F D4G E3G 41U 15G
16G 1CG 1DC 1FU 27U 27F 72G 73G 74G 75G 76G 77G 78G 79G 7AG B2S B3U
B3F B4U B4F D4S D5U D5F D6U D6F E4U E4F E5U E5F 1HU 1HF 1JU 1JF 7GG
7HG A4J E6G 7KG D7U E8U E8F E9U E9F EAS EBG 7RG 7SG 7TG)
ꢀ9ꢁ 256 MB SDRAM (models 17S 23S 1BS 1AU 21G 24U 18G 19G 1EC 22G 26G 31U
31G 32G 7BG 7CG 7EG 7DG 7JG 33G 34U 34F 35U 35F 51G 52G 53U 7NG 7PG
7QG 2AU 36U 37S 7UG 7VG)
73P2683
*
ꢀ9ꢁ 512 MB SDRAM (models 1GU)
73P2684
88P7699
13R8905
*
ꢀ10ꢁ Intel Celeron 2.4 GHz (models CTO-U CTO-G A1U A1F A2U A2F A3G 75G C1U)
ꢀ10ꢁ Intel Celeron 2.5 GHz (models CTO-U CTO-G)
* *
* *
Chapter 11. FRU lists 137
Item #
8084 FRUs
FRU#
CRU
ꢀ10ꢁ Intel Celeron 2.6 GHz (models CTO-U CTO-G D1S D2U D2F D2U D2F D3U D3F
13R8907
* *
C2U)
ꢀ10ꢁ Intel Celeron 2.7 GHz (models CTO-U CTO-G)
ꢀ10ꢁ Intel Celeron 2.8 GHz (models CTO-U CTO-G E1U E1F E2U E2F)
ꢀ10ꢁ Intel Prescott Celeron 2.4 GHz (models A4J)
13R8947
13R8963
19R0780
19R0417
* *
* *
* *
* *
ꢀ10ꢁ Intel Celeron 2.53GHz (models B1G B2G 76G CTO-U CTO-G B2S B3U B3F B4U
B4F)
ꢀ10ꢁ Intel Celeron 2.66GHz (models D4G 77G D4S D5U D5F D6U D6F D7U)
ꢀ10ꢁ Intel Celeron 2.8GHz (models E3G 78G C3U E4U E4F E5U E5F 7RG)
ꢀ10ꢁ Intel Prescott Celeron 2.93GHz (models CTO-U CTO-G E6G 7KG 7SG)
19R0419
19R0421
29R6989
29R6990
* *
* *
* *
* *
ꢀ10ꢁ Intel Prescott Celeron 3.06GHz (models CTO-U CTO-G E8U E8F E9U E9F EAS
EBG 7TG)
ꢀ10ꢁ Intel P4 2.6 GHz (models CTO-U CTO-G 41U)
ꢀ10ꢁ Intel P4 2.8 GHz (models CTO-U CTO-G 1FU 72G)
ꢀ10ꢁ Intel P4 2.66 GHz (models CTO-U CTO-G)
73P0574
19R2302
74P1629
74P1631
* *
* *
* *
* *
ꢀ10ꢁ Intel P4 2.8 GHz (models CTO-U CTO-G 1BS 1AU 11U 12G 13U 13F 14U 14F 79G
C4U)
ꢀ10ꢁ Intel P4 3.06 GHz (models CTO-U CTO-G 25U 25F 27U 27F)
ꢀ10ꢁ Intel P4 2.4 GHz (models CTO-U CTO-G)
ꢀ10ꢁ Intel P4 2.6 GHz (models CTO-U CTO-G)
ꢀ10ꢁ Intel P4 2.8 GHz (models CTO-U CTO-G)
ꢀ10ꢁ Intel P4 3.0 GHz (models CTO-U CTO-G)
ꢀ10ꢁ Intel P4 3.2 GHz (models CTO-U CTO-G)
74P1633
88P5867
88P5868
88P5869
88P5870
88P5871
19R0423
* *
* *
* *
* *
* *
* *
* *
ꢀ10ꢁ Intel Prescott P4 2.8 GHz (models CTO-U CTO-G 15G 16G 1CG 1DC 73G 74G
7AG 1HU 1HF 1JU 1JF 7GG 7HG)
ꢀ10ꢁ Intel Prescott P4 2.8 GHz (models 17S CTO-U CTO-G 18G 19G 1EC 7BG C5U
19R0292
19R0294
19R0296
* *
* *
* *
1GU)
ꢀ10ꢁ Intel Prescott P4 3.0 GHz (models 23S CTO-U CTO-G 21G 22G 24U 26G 7CG C6U
7DG 28U 28F 29U 29F 7JG 2AU 7UG)
ꢀ10ꢁ Intel Prescott P4 3.2 GHz (models CTO-U CTO-G 31U 31G 32G 7EG C7U 33G 34U
34F 35U 35F 7NG 36U 37S 7VG)
ꢀ10ꢁ Intel Prescott P4 3.4 GHz (models CTO-U CTO-G 51G 52G 53U 7PG 7QG C8U)
29R6991
32P4004
* *
* *
ꢀ11ꢁ Heat sink and fan and fan, Northwood <3.0 GHZ (models D1S D2U D2F D2U D2F
D3U D3F C2U E1U E1F E2U E2F 41U 1FU 72G 1BS 1AU 11U 12G 13U 13F 14U
14F 79G C4U CTO-U CTO-G)
ꢀ11ꢁ Heat sink and fan, Northwood >=3.0 GHZ and all Prescott (models 17S 23S 21G
24U 15G 16G 1CG 1DC 73G 74G 7AG 18G 19G 1EC 7BG C5U 31U 31G 32G 7EG
C7U 1GU B1G B2G 76G D4G 77G E3G 78G C3U 1HU 1HF 1JU 1JF 28U 28F 29U
29F 7JG 7GG 7HG B2S B3U B3F B4U B4F D4S D5U D5F D6U D6F E4U E4F E5U
E5F A4J E6G 7KG 33G 34U 34F 35U 35F 7NG 51G 52G 53U 7PG 7QG C8U 7DG
22G 24U 26G 7CG C6U 25U 25F 27U 27F CTO-U CTO-G D7U E8U E8F E9U E9F
EAS 2AU 36U 37S EBG 7TG 7RG 7SG 7UG 7VG)
13R9195
* *
138 Hardware Maintenance Manual
Item #
8084 FRUs
FRU#
CRU
ꢀ11ꢁ Heat sink and fan, Northwood >=3.0 GHZ and all Prescott, Dual Heat Pipe --
optional to 13R9195 (models 17S 23S 21G 24U 15G 16G 1CG 1DC 73G 74G 7AG
18G 19G 1EC 7BG C5U 31U 31G 32G 7EG C7U 1GU B1G B2G 76G D4G 77G E3G
78G C3U 1HU 1HF 1JU 1JF 28U 28F 29U 29F 7JG 7GG 7HG B2S B3U B3F B4U B4F
D4S D5U D5F D6U D6F E4U E4F E5U E5F A4J E6G 7KG 33G 34U 34F 35U 35F
7NG 51G 52G 53U 7PG 7QG C8U 7DG 22G 24U 26G 7CG C6U 25U 25F 27U 27F
CTO-U CTO-G D7U E8U E8F E9U E9F EAS 2AU 36U 37S EBG 7TG 7RG 7SG 7UG
7VG)
13N2951
* *
ꢀ12ꢁ Power supply, AcBel PFC, 230W (models 1AU A1U A1F A2U A2F D2U D2F E1U
E1F E2U E2F 11U 12G 13U 13F 14U 14F 21G 24U 25U 25F A3G B1G B2G D2U D2F
D3U D3F D4G E3G 41U 15G 16G 18G 19G 1CG 1FU 22G 26G 27U 27F 31U 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG C1U C2U C3U
C4U C5U C6U C7U 1GU B3U B3F B4U B4F D5U D5F D6U D6F E4U E4F E5U E5F
1HU 1HF 1JU 1JF 28U 28F 29U 29F 7GG 7HG 7JG A4J E6G 33G 34U 34F 35U 35F
51G 52G 53U 7KG 7NG 7PG 7QG C8U D7U E8U E8F E9U E9F 2AU 36U EBG 7RG
7SG 7TG 7UG 7VG)
74P4300
N
ꢀ12ꢁ Power supply, AcBel China, 230W (models 17S 23S D1S 1BS 1DC 1EC B2S D4S
74P4301
59P8542
N
**
EAS 37S)
ꢀ13ꢁ Chassis assembly (all models)
The FRUs listed in the following table are not illustrated.
8084 FRUs
Front bezel release kit (all models)
FRU#
CRU
**
25P0069
59P8564
00N5151
75H9219
19K5548
03K9655
32P4743
25P0068
22P4447
49P1750
Retainer, Adapter Cards (all models)
Speaker assembly (models D7U EAS 37S 2AU 36U)
Cable, audio (all models)
**
**
**
5.25 EMC shield (all models)
**
Rubber foot (all models)
**
Universal adapter bracket (all models)
Bezel blanks kit (all models)
**
**
80 mm fan assembly (models with 3.06 GHz microprocessor or greater)
**
2 audio front panel (models 17S 23S 7GG 7HG 7JG E6G 33G 34U 34F 35U 35F 51G 52G
53U 7KG 7NG 7PG 7QG C8U D5U 2AU 36U)
**
Cable, audio assembly (all models)
49P1933
49P4365
59P8543
59P8549
59P8545
59P8548
59P8571
59P8572
59P8568
33F8354
24P0383
**
**
**
**
**
**
*
Cable, dual USB 2.0 (all models)
Hard disk drive bracket assembly (all models)
Hard disk drive tray (all models)
Power switch assembly (all models)
Bezel, Diskette drive (all models)
Cable, 2 drop (close spacing) ATA 66/100 w/pull tabs (all models)
Cable, 2 drop** (large spacing) ATA 66/100 w/pull tabs (all models)
Cable, Diskette drive (all models)
*
*
Battery, 3.0 V (all models)
**
*
Mouse, 2 button, black (models A1U A1F A2U A2F D2U D2F E1U E1F E2U E2F 13U 13F
14U 14F 25U 25F D3U D3F 27U 27F B3U B3F B4U B4F D5U D5F D6U D6F E4U E4F E5U
E5F 1HU 1HF 1JU 1JF 28U 28F 29U 29F 34U 34F 35U 35F E8U E8F E9U E9F)
Chapter 11. FRU lists 139
8084 FRUs
FRU#
CRU
Mouse, optical wheel (models 17S 23S D1S 1BS 1AU 11U 21G 24U 41U 15G 19G 1DC 1EC
1FU 22G 31U 31G 32G 73G 74G 7BG 7CG 7EG A3G B1G B2G D4G E3G 12G 16G 18G 1CG
26G 72G 75G 76G 77G 78G 79G 7AG 7DG 1GU B2S D4S 7GG 7HG 7JG A4J E6G 33G 51G
52G 53U 7KG 7NG 7PG 7QG D7U EAS 2AU 36U 37S EBG 7RG 7SG 7TG 7UG 7VG)
89P5089
*
Cable clip (all models)
59P8584
89P4761
89P6740
13R9195
09N5764
22P7943
73P3974
29R7236
60H6043
60H6045
60H6046
60H6047
60H6048
60H6049
60H6050
60H6051
60H6052
60H6053
60H6054
60H6055
*
**
**
**
**
*
System board EMC shield kit (all models)
Retention kit (all models)
Heatsink grease, Heat pipe (all models)
Misc. hardware kit (all models)
PCI Modem Card (Soft), ATX (models D7U 2AU 36U)
PCI Serial Port Adapter (models CTO-U CTO-G)
128 MB AGP ATX VGA DVI-I S-VIDEO (models CTO-U CTO-G)
RJ11 connector adapter (Spain, Ireland) (All ″G″ models)
RJ11 connector adapter (Austria) (All ″G″ models)
RJ11 connector adapter (Belgium) (All ″G″ models)
RJ11 connector adapter (Denmark) (All ″G″ models)
RJ11 connector adapter (Norway, Finland) (All ″G″ models)
RJ11 connector adapter (France) (All ″G″ models)
RJ11 connector adapter (Germany) (All ″G″ models)
RJ11 connector adapter (UK, NZ, HK) (All ″G″, ″M″, ″B″, ″H″ models)
RJ11 connector adapter (Italy) (All ″G″ models)
RJ11 connector adapter (Netherlands) (All ″G″ models)
RJ11 connector adapter (Sweden) (All ″G″ models)
RJ11 connector adapter (Switzerland) (All ″G″ models)
*
*
*
*
*
*
*
*
*
*
*
*
*
*
8084 Windows XP Home Recovery CDs
US/UK/AP/TH (models A2U D2U E2U 13U 25U D2U B4U D6U E5U 1HU 28U 35U E8U)
FR/CF (models A2F D2F E2F 13F 25F D2F B4F D6F E5F 1HF 28F 35F E8F)
Simplified Chinese (models 1DC)
FRU#
39J6250
39J6251
30R4777
CRU
*
*
*
8084 Windows XP Pro Recovery CDs
FRU#
CRU
US (Models 1GU 1AU A1U E1U 11U 12G 14U 21G 24U A3G B1G D3U D4G E3G 41U 15G
16G 18G 19G 1CG 1FU 22G 26G 27U 31U 31G 32G 72G 74G 75G 76G 77G 78G 79G 7AG
7BG 7CG 7DG 7EG B3U D5U E4U 1JU 29U 7GG 7HG 7JG E6G 33G 34U 51G 52G 53U
7KG 7NG 7PG 7QG D7U E9U 2AU 36U EBG 7RG 7SG 7TG)
39J6414
*
FR (models A1F E1F 12G 14F 21G A3G B1G D3F D4G E3G 15G 16G 18G 19G 1CG 22G
26G 27F 31G 32G 72G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG B3F D5F E4F
1JF 29F 7GG 7HG 7JG E6G 33G 34F 51G 52G 7KG 7NG 7PG 7QG E9F EBG 7RG 7SG 7TG)
39J6415
39J6416
39J6417
*
*
*
GR (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
SP/LA (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G
72G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 17S 23S D1S 1BS D4S EAS 37S)
140 Hardware Maintenance Manual
8084 Windows XP Pro Recovery CDs
FRU#
CRU
IT (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
39J6418
*
SV (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
39J6420
39J6421
39J6422
39J6423
39J6424
39J6425
39J6426
39J6427
39J6428
41D1950
41D1949
39J6430
39J6431
39J6432
39J6433
39J6434
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
DK (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
FI (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
NO (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
NL (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
HE (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
PL (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
CZ (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
AE (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
RU (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
RE (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
TR (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
HU (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
PO (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
GK (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
SL (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
Chapter 11. FRU lists 141
8084 Windows XP Pro Recovery CDs
FRU#
CRU
JP (models A4J)
CS (models 1EC)
30R4834
30R4813
39J7221
*
*
*
Multilingual 1 (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G
32G 72G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
Multilingual 2 (models 12G 21G A3G B1G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G
32G 72G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG)
39J7222
*
8084 Keyboards (Standard PS/2 Black)
FRU#
CRU
US English (models 1AU A1U A2U D2U E1U E2U 11U 12G 13U 14U 21G 24U 25U A3G
B1G B2G D2U D3U D4G E3G 41U 15G 16G 18G 19G 1CG 1DC 1EC 1FU 22G 26G 27U
31U 31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 1GU B3U B4U
D5U D6U E4U E5U 1HU 1JU 28U 29U 7GG 7HG 7JG E6G 33G 34U 35U 51G 52G 53U
7KG 7NG 7PG 7QG D7U E8U E9U 2AU 36U EBG 7RG 7SG 7TG 7UG 7VG)
89P8300
*
Arabic (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
89P8301
89P8302
89P8303
89P8305
*
*
*
*
Belgian/French (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G
31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G
33G 51G 52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Belgian/UK (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G
51G 52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Bulgarian (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Chinese/US (models 21G)
89P8306
89P8307
*
*
Czech (mmodels 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Danish (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
89P8308
89P8309
89P8310
*
*
*
Dutch (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
French (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
French Canadian (models A1F A2F D2F E1F E2F 14F 25F D2F D3F 27F B3F B4F D5F D6F
E4F E5F 1HF 1JF 28F 29F 34F 35F E8F E9F)
89P8311
89P8312
89P8313
*
*
*
French Canadian (models A1F A2F D2F E1F E2F 14F 25F D2F D3F 27F B3F B4F D5F D6F
E4F E5F 1HF 1JF 28F 29F 34F 35F E8F E9F)
German (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Greek (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G
7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
89P8314
*
142 Hardware Maintenance Manual
8084 Keyboards (Standard PS/2 Black)
FRU#
CRU
Hebrew (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
89P8315
*
Hungarian (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G
51G 52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
89P8316
89P8317
89P8318
89P8319
*
*
*
*
Iceland (mmodels 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Italian 141 (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Italian 142 (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Japanese (models A4J)
89P8320
89P8322
89P8323
*
*
*
LA Spanish (models 17S 23S D1S 1BS B2S D4S EAS 37S)
Norwegian (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G
51G 52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Polish (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
89P8324
89P8325
89P8326
89P8327
89P8328
89P8329
89P8330
89P8331
89P8332
89P8333
*
*
*
*
*
*
*
*
*
*
Portuguese (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G
51G 52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Romanian (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Russian/Cy (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G
51G 52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Russian/Cy (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G
51G 52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Serbian/Cyrillic (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G
31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G
33G 51G 52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Slovak (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Spanish (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Swedish/Finn (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G
51G 52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Swiss F/G (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Chapter 11. FRU lists 143
8084 Keyboards (Standard PS/2 Black)
FRU#
CRU
Turkish (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
89P8335
*
Turkish (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G
52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
89P8336
89P8337
89P8338
89P8339
*
*
*
*
UK English (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G 33G
51G 52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
US International (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G
31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G
33G 51G 52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Yugoslav/Latin (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G 26G
31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG E6G
33G 51G 52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
8084 Power Cords
FRU#
CRU
Power Cord (models 17S 23S D1S 1BS 1AU A1U A1F A2U A2F D2U D2F E1U E1F E2U
E2F 11U 12G 13U 13F 14U 14F 21G 24U 25U 25F A3G B1G B2G D2U D2F D3U D3F D4G
E3G 41U 15G 16G 18G 19G 1CG 1FU 22G 26G 27U 27F 31U 31G 32G 72G 73G 74G 75G
76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG C1U C2U C3U C4U C5U C6U C7U 1GU B2S
B3U B3F B4U B4F D4S D5U D5F D6U D6F E4U E4F E5U E5F 1HU 1HF 1JU 1JF 28U 28F
29U 29F 7GG 7HG 7JG E6G 33G 34U 34F 35U 35F 51G 52G 53U 7KG 7NG 7PG 7QG C8U
D7U E8U E8F E9U E9F EAS 2AU 36U 37S EBG 7RG 7SG 7TG 7UG 7VG)
6952301
*
Power Cord (EMEA, ANZ, ASEAN Eng, Korea) (models 21G A3G B1G B2G D4G E3G 15G
16G 18G 19G 1CG 22G 26G 31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG
7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG
7VG)
13F9978
14F0032
*
*
Power Cord (EMEA, ANZ, ASEAN Eng, HK Eng) (models 21G A3G B1G B2G D4G E3G
15G 16G 18G 19G 1CG 22G 26G 31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG
7CG 7DG 7EG 7GG 7HG 7JG E6G 33G 51G 52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG
7UG 7VG)
Power Cord (EMEA) (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G
26G 31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG
E6G 33G 51G 52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
13F9996
14F0068
*
*
Power Cord (EMEA, LA) (models 17S 23S D1S 1BS 21G A3G B1G B2G D4G E3G 15G 16G
18G 19G 1CG 22G 26G 31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG
7EG B2S D4S 7GG 7HG 7JG E6G 33G 51G 52G 7KG 7NG 7PG 7QG EAS 37S EBG 7RG
7SG 7TG 7UG 7VG)
Power Cord (Japan) (models A4J)
1838576
02K0545
14F0086
*
*
*
Power Cord (China, HK) (models 1DC 1EC)
Power Cord (EMEA) (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G
26G 31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG
E6G 33G 51G 52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
Power Cord (EMEA, ANZ, ASEAN Eng) (models 21G A3G B1G B2G D4G E3G 15G 16G
18G 19G 1CG 22G 26G 31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG
7EG 7GG 7HG 7JG E6G 33G 51G 52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
14F0014
14F0050
*
*
Power Cord (EMEA) (models 21G A3G B1G B2G D4G E3G 15G 16G 18G 19G 1CG 22G
26G 31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG 7GG 7HG 7JG
E6G 33G 51G 52G 7KG 7NG 7PG 7QG EBG 7RG 7SG 7TG 7UG 7VG)
144 Hardware Maintenance Manual
Machine Type 8085
Item #
8085 FRUs
FRU#
CRU
**
ꢀ1ꢁ Side cover assembly (all models)
ꢀ2ꢁ ″L″ Cover assembly (all models)
ꢀ3ꢁ Front Bezel assembly (all models)
ꢀ4ꢁ Bezel trim/label kit (all models)
59P8547
59P8546
59P8544
49P1900
71P7367
**
**
**
ꢀ5ꢁ CD-ROM Drive 48X (Black) - w/o volume ctrl and headphone jack (models A1U
15U 15F 15G 33U 33F D2U 41U 11U 13G 19U 21U 21F 21G 35G A4U A5S A5D
A5Y B1U B2S B2D B2Y 7DG 1DU 1DF 51U 51F 51G A6J A7J A8J B4J B5J B6J 1GJ
2BJ E5J E6J E7J E9J EAJ EBJ)
*
ꢀ5ꢁ CD-ROM Drive 48X (Black) - w/o volume ctrl and headphone jack (models A1U
15U 15F 15G 33U 33F D2U 41U 11U 13G 19U 21U 21F 21G 35G A4U A5S A5D
A5Y B1U B2S B2D B2Y 7DG 1DU 1DF 51U 51F 51G A6J A7J A8J B4J B5J B6J 1GJ
2BJ E5J E6J E7J E9J EAJ EBJ)
71P7385
71P7375
*
*
ꢀ5ꢁ CD-ROM Drive 48X (Black) - w/o volume ctrl and headphone jack (models A1U
15U 15F 15G 33U 33F D2U 41U 11U 13G 19U 21U 21F 21G 35G A4U A5S A5D
A5Y B1U B2S B2D B2Y 7DG 1DU 1DF 51U 51F 51G A6J A7J A8J B4J B5J B6J 1GJ
2BJ E5J E6J E7J E9J EAJ EBJ)
Chapter 11. FRU lists 145
Item #
8085 FRUs
FRU#
CRU
ꢀ5ꢁ CD-ROM Drive 48X (Black) - w/o volume ctrl and headphone jack (models A1U
15U 15F 15G 33U 33F D2U 41U 11U 13G 19U 21U 21F 21G 35G A4U A5S A5D
A5Y B1U B2S B2D B2Y 7DG 1DU 1DF 51U 51F 51G A6J A7J A8J B4J B5J B6J 1GJ
2BJ E5J E6J E7J E9J EAJ EBJ)
71P7371
*
ꢀ5ꢁ DVD-ROM 16X/48X (Black) (models 34S 34D 34Y 32U D3U 16G 1AU 1AS 1AD
71P7357
26K5385
26K5435
71P7347
*
*
*
*
1AY 22G 36G 71G 72G 75G 78G 79G 7AG D5U 28U 52G 7EG 7FG)
ꢀ5ꢁ DVD-ROM 16X/48X (Black) (models 34S 34D 34Y 32U D3U 16G 1AU 1AS 1AD
1AY 22G 36G 71G 72G 75G 78G 79G 7AG D5U 28U 52G 7EG 7FG)
ꢀ5ꢁ DVD-ROM 16X/48X (Black) (models 34S 34D 34Y 32U D3U 16G 1AU 1AS 1AD
1AY 22G 36G 71G 72G 75G 78G 79G 7AG D5U 28U 52G 7EG 7FG)
ꢀ5ꢁ CD-RW Drive (48X/32X/48X) (models A2S A2D A2Y D1S D1D D1Y E3S E3D E3Y
14S 14D 14Y 23U A3U D3U D4S D4D D4Y 42U 42S 42D 42Y 18U 1AU 1AS 1AD
1AY D5U B3U 1CU 37U 28U E8S)
ꢀ5ꢁ CD-RW Drive (48X/32X/48X) (models A2S A2D A2Y D1S D1D D1Y E3S E3D E3Y
14S 14D 14Y 23U A3U D3U D4S D4D D4Y 42U 42S 42D 42Y 18U 1AU 1AS 1AD
1AY D5U B3U 1CU 37U 28U E8S)
71P7349
*
ꢀ5ꢁ 48X Combo drive (models 17S 17D 17Y 24S 24D 24Y 27S 27D 27Y 24U 31U E1U
26K5379
26K5381
*
*
1BU 73G 74G 76G 77G 7BG 7CG E4G 53U 7GG 7HG 1EJ 1FJ 29J 2AJ 1HJ 38S)
ꢀ5ꢁ 48X Combo drive (models 17S 17D 17Y 24S 24D 24Y 27S 27D 27Y 24U 31U E1U
1BU 73G 74G 76G 77G 7BG 7CG E4G 53U 7GG 7HG 1EJ 1FJ 29J 2AJ 1HJ 38S)
ꢀ5ꢁ Rambo IV (Black) (models 34S 34D 34Y 32U)
26K5383
76H4091
*
*
ꢀ6ꢁ Diskette drive, 3.5 1.44MB (models 34S 34D 34Y A2S A2D A2Y D1S D1D D1Y E3S
E3D E3Y 14S 14D 14Y 17S 17D 17Y 24S 24D 24Y 27S 27D 27Y 15U 15F 15G 23U
24U 31U 32U 33U 33F A3U D3U D4S D4D D4Y E1U 42U 42S 42D 42Y 13G 16G
18U 1AU 1AS 1AD 1AY 1BU 21U 21F 21G 22G 35G 36G 71G 72G 73G 74G 75G
76G 77G 78G 79G 7AG 7BG 7CG A5S A5D A5Y B2S B2D B2Y D5U 7DG B3U E4G
1CU 1DU 1DF 28U 37U 51U 51F 51G 52G 53U 7EG 7FG 7GG 7HG A6J A7J A8J
B4J B5J B6J 1EJ 1FJ 1GJ 29J 2AJ 2BJ E5J E6J E7J 1HJ E8S 38S E9J EAJ EBJ)
ꢀ6ꢁ Diskette drive, 3.5 1.44MB (optional to 76H4091) (models 34S 34D 34Y A2S A2D
A2Y D1S D1D D1Y E3S E3D E3Y 14S 14D 14Y 17S 17D 17Y 24S 24D 24Y 27S 27D
27Y 15U 15F 15G 23U 24U 31U 32U 33U 33F A3U D3U D4S D4D D4Y E1U 42U
42S 42D 42Y 13G 16G 18U 1AU 1AS 1AD 1AY 1BU 21U 21F 21G 22G 35G 36G
71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG A5S A5D A5Y B2S B2D
B2Y D5U 7DG B3U E4G 1CU 1DU 1DF 28U 37U 51U 51F 51G 52G 53U 7EG 7FG
7GG 7HG A6J A7J A8J B4J B5J B6J 1EJ 1FJ 1GJ 29J 2AJ 2BJ E5J E6J E7J 1HJ E8S 38S
E9J EAJ EBJ)
33P3343
*
ꢀ7ꢁ Hard disk drive, 40GB EIDE (models A1U 15U 15F 15G 23U 33U 33F A3U D2U
D3U E1U 41U 42U 42S 42D 42Y 11U 13G 18U 19U 1AU 1AS 1AD 1AY 21U 21F
21G 35G 71G 75G 79G A4U A5S A5D A5Y B1U B2S B2D B2Y D5U 7DG B3U E4G
1CU 1DU 1DF 28U 37U 51U 51F 51G 7EG A6J A7J A8J B4J B5J B6J 1GJ 2BJ E5J E6J
E7J E9J EAJ EBJ)
40Y8757
40Y8758
*
*
ꢀ7ꢁ Hard disk drive, 80GB EIDE (models 34S 34D 34Y A2S A2D A2Y D1S D1D D1Y
E3S E3D E3Y 14S 14D 14Y 17S 17D 17Y 24U 24F 24S 24D 24Y 27S 27D 27Y 31U
D4S D4D D4Y 16G 1BU 22G 36G 72G 78G 7AG 52G 53U 7FG 1EJ 1FJ 29J 2AJ 1HJ
E8S 38S)
ꢀ7ꢁ Hard disk drive, 120GB EIDE (models 32U)
40Y8759
71P7293
40Y8761
71P7297
40Y8762
40Y9035
*
*
*
*
*
*
ꢀ7ꢁ Hard disk drive, 80GB S-ATA (models 74G 77G 7CG 7HG)
ꢀ7ꢁ Hard disk drive, 80GB S-ATA (models 74G 77G 7CG 7HG)
ꢀ7ꢁ Hard disk drive, 160GB S-ATA (models 73G 76G 7BG 7GG)
ꢀ7ꢁ Hard disk drive, 160GB S-ATA (models 73G 76G 7BG 7GG)
ꢀ7ꢁ Hard disk drive, 160GB S-ATA (models 73G 76G 7BG 7GG)
146 Hardware Maintenance Manual
Item #
8085 FRUs
FRU#
CRU
ꢀ8ꢁ System board, 10/100 E-net (models 34S 34D 34Y 14S 14D 14Y 17S 17D 17Y 24S
24D 24Y 27S 27D 27Y 15U 15F 15G 23U 24U 31U 32U 33U 33F 13G 16G 18U 21U
21F 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG
C4U C5U C6U C7U 7DG 1DU 1DF 28U 37U 51U 51F 51G 52G 53U 7EG 7FG 7GG
7HG CDU 1FJ 1GJ 1EJ 29J 2AJ 2BJ 1HJ 38S)
19R0703
**
ꢀ8ꢁ System board, (10/100 Enet) w/ video buffer -- optional to 19R0703 (models 34S
34D 34Y 14S 14D 14Y 17S 17D 17Y 24S 24D 24Y 27S 27D 27Y 15U 15F 15G 23U
24U 31U 32U 33U 33F 13G 16G 18U 21U 21F 21G 22G 35G 36G 71G 72G 73G 74G
75G 76G 77G 78G 79G 7AG 7BG 7CG C4U C5U C6U C7U 7DG 1DU 1DF 28U 37U
51U 51F 51G 52G 53U 7EG 7FG 7GG 7HG CDU 1FJ 1GJ 1EJ 29J 2AJ 2BJ 1HJ 38S)
39J7965
41D0948
19R0837
39J7966
41D0949
**
**
**
**
**
ꢀ8ꢁ System board, (10/100 Enet) w/ video buffer -- optional to 19R0703 (models 34S
34D 34Y 14S 14D 14Y 17S 17D 17Y 24S 24D 24Y 27S 27D 27Y 15U 15F 15G 23U
24U 31U 32U 33U 33F 13G 16G 18U 21U 21F 21G 22G 35G 36G 71G 72G 73G 74G
75G 76G 77G 78G 79G 7AG 7BG 7CG C4U C5U C6U C7U 7DG 1DU 1DF 28U 37U
51U 51F 51G 52G 53U 7EG 7FG 7GG 7HG CDU 1FJ 1GJ 1EJ 29J 2AJ 2BJ 1HJ 38S)
ꢀ8ꢁ System board, 10/100 E-net, no AGP (models A2S A2D A2Y D1S D1D D1Y E3S
E3D E3Y A1U A3U D2U D3U D4S D4D D4Y E1U 41U 42U 42S 42D 42Y 11U 19U
1AU 1AS 1AD 1AY 1BU C1U C2U C3U A4U A5S A5D A5Y B1U B2S B2D B2Y
D5U C8U C9U CAU B3U E4G 1CU CBU A7J A8J A6J B4J B5J B6J E5J E6J E7J E8S
E9J EAJ EBJ)
ꢀ8ꢁ System board, (10/100 Enet) w/ video buffer, no AGP -- optional to
19R0837(models A2S A2D A2Y D1S D1D D1Y E3S E3D E3Y A1U A3U D2U D3U
D4S D4D D4Y E1U 41U 42U 42S 42D 42Y 11U 19U 1AU 1AS 1AD 1AY 1BU C1U
C2U C3U A4U A5S A5D A5Y B1U B2S B2D B2Y D5U C8U C9U CAU B3U E4G
1CU CBU A7J A8J A6J B4J B5J B6J E5J E6J E7J E8S E9J EAJ EBJ)
ꢀ8ꢁ System board, (10/100 Enet) w/ video buffer, no AGP -- optional to
19R0837(models A2S A2D A2Y D1S D1D D1Y E3S E3D E3Y A1U A3U D2U D3U
D4S D4D D4Y E1U 41U 42U 42S 42D 42Y 11U 19U 1AU 1AS 1AD 1AY 1BU C1U
C2U C3U A4U A5S A5D A5Y B1U B2S B2D B2Y D5U C8U C9U CAU B3U E4G
1CU CBU A7J A8J A6J B4J B5J B6J E5J E6J E7J E8S E9J EAJ EBJ)
ꢀ9ꢁ 128 MB SDRAM PC2700 (models A2S A2D A2Y D1S D1D D1Y A1U D2U 41U 11U
31P9120
31P9121
*
*
19U A4U A5S A5D A5Y B1U A8J B5J E7J EBJ)
ꢀ9ꢁ 256 MB SDRAM PC2700 (models E3S E3D E3Y 14S 14D 14Y 27S 27D 27Y A3U
D3U D4S D4D D4Y E1U 42U 42S 42D 42Y 1AU 1AS 1AD 1AY 1BU B2S B2D B2Y
D5U 7DG B3U E4G 1CU 1DU 1DF A6J A7J B4J B6J E5J E6J E8S E9J EAJ)
ꢀ9ꢁ 512 MB SDRAM PC2700 (models 1EJ 1FJ 1GJ 1HJ)
31P9122
73P2683
*
*
ꢀ9ꢁ 256 MB SDRAM PC3200 (models 34S 34D 34Y 17S 17D 17Y 24S 24D 24Y 15U 15F
15G 23U 24U 31U 32U 33U 33F 13G 16G 18U 21U 21F 21G 22G 35G 36G 71G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 28U 37U 51U 51F 51G 52G 53U
7EG 7FG 7GG 7HG 38S)
ꢀ9ꢁ 512 MB SDRAM PC3200 (models 29J 2AJ 2BJ)
73P2684
88P7699
13R8907
13R8963
19R0780
19R0417
19R0419
19R0421
29R6989
29R6990
*
ꢀ10ꢁ Intel Celeron 2.4 GHz (models A2S A2D A2Y A1U A3U C1U)
ꢀ10ꢁ Intel Celeron 2.6 GHz (models D1S D1D D1Y D2U D3U C2U)
ꢀ10ꢁ Intel Celeron 2.8 GHz (models E3S E3D E3Y)
* *
* *
* *
* *
* *
* *
* *
* *
* *
ꢀ10ꢁ Intel Celeron 2.4 GHz (models A4U A5S A5D A5Y C8U A6J A7J A8J)
ꢀ10ꢁ Intel Celeron 2.53 GHz (models B1U B2S B2D B2Y C9U B3U B4J B5J B6J)
ꢀ10ꢁ Intel Celeron 2.66 GHz (models D4S D4D D4Y D5U CAU)
ꢀ10ꢁ Intel Celeron 2.8 GHz (models E1U C3U E5J E6J E7J)
ꢀ10ꢁ Intel Celeron 2.93 GHz (models E4G CBU E9J EAJ EBJ)
ꢀ10ꢁ Intel Celeron 3.06 GHz (models E8S)
Chapter 11. FRU lists 147
Item #
8085 FRUs
FRU#
CRU
* *
ꢀ10ꢁ Intel P4 2.6 GHz (models 41U 42U 42S 42D 42Y)
ꢀ10ꢁ Intel P4 2.8 GHz (models 19U 1AU 1AS 1AD 1AY)
ꢀ10ꢁ Intel P4 2.8 GHz (models 11U C4U)
73P0574
19R2302
74P1631
74P1633
19R0423
* *
* *
ꢀ10ꢁ Intel P4 3.06 GHz (models 27S 27D 27Y)
* *
ꢀ10ꢁ Intel P4 2.8 GHz (models 14S 14D 14Y 13G 1BU 7DG 1CU 1DU 1DF 1EJ 1FJ 1GJ
* *
1HJ)
ꢀ10ꢁ Intel P4 2.8 GHz (models 17S 17D 17Y 15U 15F 15G 16G 18U 71G 72G 73G 74G
19R0292
19R0294
19R0296
* *
* *
* *
C5U)
ꢀ10ꢁ Intel P4 3.0 GHz (models 24S 24D 24Y 23U 24U 21U 21F 75G 76G 77G 78G C6U
28U 29J 2AJ 2BJ)
ꢀ10ꢁ Intel P4 3.2 GHz (models 34S 34D 34Y 31U 32U 33U 33F 35G 36G 79G 7AG 7BG
7CG C7U 37U 38S)
ꢀ10ꢁ Intel P4 3.4 GHz (models 51U 51F 51G 52G 53U 7EG 7FG 7GG 7HG CDU)
29R6991
32P4004
* *
* *
ꢀ11ꢁ Heat sink and fan, Northwood <3.0 GHZ (models A2S A2D A2Y A1U A3U C1U
D1S D1D D1Y D2U D3U C2U E3S E3D E3Y 41U 42U 42S 42D 42Y 19U 1AU 1AS
1AD 1AY 11U C4U)
ꢀ11ꢁ Heat sink and fan, Northwood >=3.0 GHZ and all Prescott (models 34S 34D 34Y
17S 17D 17Y 24S 24D 24Y 15U 15F 15G 23U 24U 31U 32U 33U 33F 13G 1BU 16G
18U 71G 72G 73G 74G C5U 21U 21F 75G 76G 77G 78G C6U 35G 36G 79G 7AG
7BG 7CG C7U D4S D4D D4Y E1U C3U A4U A5S A5D A5Y C8U B1U B2S B2D
B2Y C9U D5U CAU 7DG B3U 1CU 1DU 1DF 28U 37U 51U 51F 51G 52G 53U 7EG
7FG 7GG 7HG CDU 27S 27D 27Y A6J A7J A8J B4J B5J B6J 1EJ 1FJ 1GJ 29J 2AJ 2BJ
E5J E6J E7J 1HJ E8S 38S E9J EAJ EBJ)
13R9195
13N2951
74P4300
* *
* *
N
ꢀ11ꢁ Heat sink and fan, Northwood >=3.0 GHZ and all Prescott, Dual Heat Pipe --
optional to 13R9195 (models 34S 34D 34Y 17S 17D 17Y 24S 24D 24Y 15U 15F 15G
23U 24U 31U 32U 33U 33F 13G 1BU 16G 18U 71G 72G 73G 74G C5U 21U 21F 75G
76G 77G 78G C6U 35G 36G 79G 7AG 7BG 7CG C7U D4S D4D D4Y E1U C3U A4U
A5S A5D A5Y C8U B1U B2S B2D B2Y C9U D5U CAU 7DG B3U 1CU 1DU 1DF
28U 37U 51U 51F 51G 52G 53U 7EG 7FG 7GG 7HG CDU 27S 27D 27Y A6J A7J
A8J B4J B5J B6J 1EJ 1FJ 1GJ 29J 2AJ 2BJ E5J E6J E7J 1HJ E8S 38S E9J EAJ EBJ)
ꢀ12ꢁ Power supply, AcBel PFC, 230W (models A1U 15U 15F 15G 23U 24U 31U 32U 33U
33F A3U D2U D3U E1U 41U 42U 11U 13G 16G 18U 19U 1AU 1BU 21U 21F 21G
22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG C1U C2U
C3U C4U C5U C6U C7U A4U B1U D5U 7DG C8U C9U CAU B3U E4G 1CU 1DU
1DF 28U 37U 51U 51F 51G 52G 53U 7EG 7FG 7GG 7HG CBU CDU ADD A6J A7J
A8J B4J B5J B6J 1EJ 1FJ 1GJ 29J 2AJ 2BJ E5J E6J E7J 1HJ E9J EAJ EBJ)
ꢀ12ꢁ Power supply, AcBel China, 230W (models 34S 34D 34Y A2S A2D A2Y D1S D1D
D1Y E3S E3D E3Y 14S 14D 14Y 17S 17D 17Y 24S 24D 24Y 27S 27D 27Y D4S D4D
D4Y 42S 42D 42Y 1AS 1AD 1AY A5S A5D A5Y B2S B2D B2Y E8S 38S)
74P4301
59P8542
N
**
ꢀ13ꢁ Chassis assembly (all models)
The FRUs listed in the following tables are not illustrated.
8085 FRUs
Front bezel release kit (all models)
Retainer, Adapter Cards (all models)
Cable, audio (all models)
FRU#
CRU
**
25P0069
59P8564
75H9219
19K5548
03K9655
**
**
5.25 EMC shield (all models)
**
Rubber foot (all models)
**
148 Hardware Maintenance Manual
8085 FRUs
FRU#
CRU
**
PCMCIA Asm (all models)
59P8587
25P0084
32P4743
25P0068
22P4447
49P1750
1394 (6-pin) Cable (models 73G 76G 7BG)
Universal adapter bracket (all models)
**
**
Bezel blanks kit (all models)
**
80 mm fan assembly (models with 3.06 GHz microprocessor or greater)
**
2 audio front panel (models 34S 34D 34Y 24U 24S 24D 24Y 31U 32U A2S A2D A2Y D1S
D1D D1Y D4S D4D D4Y E3S E3D E3Y 14S 14D 14Y 17S 17D 17Y 74G 77G 7CG A5S A5D
A5Y B2S B2D B2Y 7DG 7GG 7HG 29J 2AJ 2BJ E8S 38S)
**
2 Audio w/1394 Fr Pnl (models 73G 76G 7BG)
Cable, audio assembly (all models)
49P1752
49P1933
49P4365
03R0293
59P8543
59P8549
59P8545
59P8548
59P8561
59P8571
59P8572
59P8568
59P8584
33F8354
24P0383
89P5089
**
**
**
**
**
**
**
**
**
*
Cable, dual USB 2.0 (all models)
Cable, SATA (all models)
Hard disk drive bracket assembly (all models)
Hard disk drive tray (all models)
Power switch assembly (all models)
Bezel, Diskette drive (all models)
90 deg, 6-pin, 1394 cable (models 73G 76G 7BG 7GG)
Cable, 2 drop (close spacing) ATA 66/100 w/pull tabs (all models)
Cable, 2 drop** (large spacing) ATA 66/100 w/pull tabs (all models)
Cable, Diskette drive (all models)
*
*
Cable clip (all models)
*
Battery, 3.0 V (all models)
*
Mouse, 2 button, black (models A1U D2U 41U 11U 19U)
*
Mouse, optical wheel (models 34S 34D 34Y A2S A2D A2Y D1S D1D D1Y E3S E3D E3Y 14S
14D 14Y 17S 17D 17Y 24S 24D 24Y 27S 27D 27Y 15U 15F 15G 23U 24U 31U 32U 33U 33F
A3U D3U D4S D4D D4Y E1U 42U 42S 42D 42Y 13G 16G 18U 1AU 1AS 1AD 1AY 1BU
21U 21F 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG A4U
A5S A5D A5Y B1U B2S B2D B2Y D5U 7DG B3U E4G 1CU 1DU 1DF 28U 37U 51U 51F
51G 52G 53U 7EG 7FG 7GG 7HG A6J A7J A8J B4J B5J B6J 1EJ 1FJ 1GJ 29J 2AJ 2BJ E5J E6J
E7J 1HJ E8S 38S E9J EAJ EBJ)
*
Speakers, Infinity Active T1 (Black) (models 34S 34D 34Y A2S A2D A2Y D1S D1D D1Y E3S
E3D E3Y 14S 14D 14Y 17S 17D 17Y 24S 24D 24Y 27S 27D 27Y 23U 24U 31U 32U A3U D3U
D4S D4D D4Y E1U 42U 42S 42D 42Y 18U 1AU 1AS 1AD 1AY 1BU 73G 76G 7BG A5S A5D
A5Y B2S B2D B2Y D5U B3U E4G 1CU 28U 37U 53U 7GG E8S 38S)
25P4726
10K2587
*
*
Speaker Power brick - US, CE, CF, LA, Taiwan (models 34S 34D 34Y A2S A2D A2Y D1S
D1D D1Y E3S E3D E3Y 14S 14D 14Y 17S 17D 17Y 24S 24D 24Y 27S 27D 27Y 23U 24U 31U
32U A3U D3U D4S D4D D4Y E1U 42U 42S 42D 42Y 18U 1AU 1AS 1AD 1AY 1BU A5S
A5D A5Y B2S B2D B2Y D5U B3U 28U 37U 53U E8S 38S)
Speaker Power brick - Europe (non-UK) (models 73G 76G 7BG E4G 7GG)
25P5704
25P5703
01R2253
*
*
*
Speaker Power brick - UK, Hong Kong (3 prong) (models 73G 76G 7BG E4G 7GG)
Speaker Power brick - Argentina (models 34S 34Y A2S A2Y D1S D1Y E3S E3Y 14S 14Y 17S
17Y 24S 24Y 27S 27Y D4S D4Y 42S 42Y 1AS 1AY A5S A5Y B2S B2Y E8S 38S)
System board EMC shield kit (all models)
Retention kit (all models)
89P4761
89P6740
13R9195
**
**
**
Heatsink grease, Heat pipe (all models)
Chapter 11. FRU lists 149
8085 FRUs
FRU#
CRU
Misc. hardware kit (all models)
09N5764
22P7943
**
*
Soft modem V.92/V.44 (models 34S 34D 34Y A2S A2D A2Y D1S D1D D1Y E3S E3D E3Y
14S 14D 14Y 17S 17D 17Y 24S 24D 24Y 27S 27D 27Y 23U 24U 31U 32U A3U D3U D4S D4D
D4Y E1U 42U 42S 42D 42Y 18U 1AU 1AS 1AD 1AY 1BU 73G 76G 7BG A5S A5D A5Y B2S
B2D B2Y D5U B3U E4G 1CU 28U 37U 53U 7GG E8S 38S)
64MB, Nvidia GeForce MX 440 (VGA) ATX (models 34S 34D 34Y 24S 24D 24Y 24U 31U
32U)
73P0715
*
64MB NVidia Quadro4 200NVS (LP/ATX) (models73G 76G 7BG 7GG)
1394 Firewire PCI LP (ATX) (models 73G 76G 7BG)
1394 Firewire PCI LP (ATX) (models 73G 76G 7BG)
RJ11 connector adapter (Spain, Ireland) (All ″G″ models)
RJ11 connector adapter (Austria) (All ″G″ models)
RJ11 connector adapter (Belgium) (All ″G″ models)
RJ11 connector adapter (Denmark) (All ″G″ models)
RJ11 connector adapter (Norway, Finland) (All ″G″ models)
RJ11 connector adapter (France) (All ″G″ models)
25P6684
73P2608
73P2609
60H6043
60H6045
60H6046
60H6047
60H6048
60H6049
60H6050
60H6051
60H6052
60H6053
60H6054
60H6055
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
RJ11 connector adapter (Germany) (All ″G″ models)
RJ11 connector adapter (UK, NZ, HK) (All ″G″, ″M″, ″B″, ″H″ models)
RJ11 connector adapter (Italy) (All ″G″ models)
RJ11 connector adapter (Netherlands) (All ″G″ models)
RJ11 connector adapter (Sweden) (All ″G″ models)
RJ11 connector adapter (Switzerland) (All ″G″ models)
8085 Windows XP Home Recovery CDs
FRU#
39J6250
CRU
US (models A1U 23U 24U 31U 32U A3U D2U D3U E1U 41U 42U 11U 18U 19U
1AU 1BU A4U B1U D5U B3U E4G 1CU 28U 37U 53U)
*
FR (models E4G)
GR (models E4G)
39J6251
39J6252
39J6253
*
*
*
SP/LA (models 34S 34D 34Y A2S A2D A2Y D1S D1D D1Y E3S E3D E3Y 14S 14D
14Y 17S 17D 17Y 24S 24D 24Y 27S 27D 27Y D4S D4D D4Y 42S 42D 42Y 1AS 1AD
1AY A5S A5D A5Y B2S B2D B2Y E4G E8S 38S)
IT (models E4G)
DK (models E4G)
NL (models E4G)
AE (models E4G)
SV (models E4G)
HE (models E4G)
FI (models E4G)
NO (models E4G)
PL (models E4G)
PO (models E4G)
RU (models E4G)
RE (models E4G)
39J6254
39J6257
39J6260
39J6264
39J6256
39J6261
39J6258
39J6259
39J6262
39J6268
41D1948
41D1947
*
*
*
*
*
*
*
*
*
*
*
*
150 Hardware Maintenance Manual
8085 Windows XP Home Recovery CDs
FRU#
39J6267
39J6263
39J6266
39J6269
30R4798
CRU
HU (models E4G)
CZ (models E4G)
TR (models E4G)
GK (models E4G)
*
*
*
*
*
JP (models A7J A8J B5J B6J 1FJ 1GJ 2AJ 2BJ E6J E7J 1HJ E9J EAJ EBJ)
8085 Windows XP Pro Recovery CDs
FRU#
CRU
US (Models 15U 15G 33U 13G 16G 21U 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG 1DU 51U 51G 52G 7EG 7FG 7GG 7HG)
39J6414
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
FR (models 15F 15G 33F 13G 16G 21F 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG 1DF 51F 51G 52G 7EG 7FG 7GG 7HG)
39J6415
39J6416
39J6418
39J6417
39J6421
39J6424
39J6428
39J6420
39J6425
39J6422
39J6423
39J6426
39J6432
41D1950
41D1949
39J6431
39J6427
39J6430
39J6433
GR (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
IT (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG
7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
SP (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG
7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
DK (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
NL (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
AE (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
SV (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG
7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
HE (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
FI (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG
7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
NO (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
PL (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG
7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
PO (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
RU (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
RE (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG
7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
HU (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
CZ (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
TR (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG
7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
GK (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
Chapter 11. FRU lists 151
8085 Windows XP Pro Recovery CDs
FRU#
CRU
SL (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG
7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
39J6434
*
JP (models A6J B4J 1EJ 29J E5J E9J)
30R4834
39J7221
*
*
Multilingual 1 (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
Multilingual 2 (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG 51G 52G 7EG 7FG 7GG 7HG)
39J7222
*
8085 Keyboard (Preferred Pro Fullsize, PS/2, Stealth Black)
FRU#
CRU
US English (models A1U 15U 15G 23U 24U 31U 33U A3U D2U D3U E1U 41U 42U 11U
13G 16G 18U 19U 1AU 1BU 21U 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G
79G 7AG 7BG 7CG A4U B1U D5U 7DG B3U E4G 1CU 1DU 28U 37U 51U 51G 52G 53U
7EG 7FG 7GG 7HG)
89P8300
*
Arabic (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
89P8301
89P8302
89P8303
89P8305
*
*
*
*
Belgian/French (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Belgian/UK (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G
79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Bulgarian (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G
79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Chinese/US (models 15G)
89P8306
89P8307
*
*
Czech (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Danish (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
89P8308
89P8309
89P8310
*
*
*
Dutch (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
French (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
French Canadian (models 15F 33F 21F 1DF 51F)
French Canadian (models 15F 33F 21F 1DF 51F)
89P8311
89P8312
89P8313
*
*
*
German (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Greek (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
89P8314
89P8315
89P8316
89P8317
89P8318
89P8319
*
*
*
*
*
*
Hebrew (models15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Hungarian (models s 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G
79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Iceland (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Italian 141 (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G
79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Italian 142 (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G
79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
152 Hardware Maintenance Manual
8085 Keyboard (Preferred Pro Fullsize, PS/2, Stealth Black)
FRU#
CRU
Japan (models A6J A7J A8J B4J B5J B6J 1EJ 1FJ 1GJ 29J 2AJ 2BJ E5J E6J E7J 1HJ E9J EAJ
EBJ)
89P8320
*
LA Spanish (models 34S 34D 34Y A2S A2D A2Y D1S D1D D1Y E3S E3D E3Y 14S 14D 14Y
17S 17D 17Y 24S 24D 24Y 27S 27D 27Y D4S D4D D4Y 42S 42D 42Y 1AS 1AD 1AY A5S
A5D A5Y B2S B2D B2Y E8S 38S)
89P8322
*
Norwegian (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G
79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
89P8323
89P8324
89P8325
89P8326
89P8327
89P8328
89P8329
89P8330
89P8331
89P8332
89P8333
89P8335
89P8336
89P8337
89P8338
89P8339
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Polish (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Portuguese (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G
79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Romanian (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G
79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Russian/Cy (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G
79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Russian/Cy (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G
79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Serbian/Cyrillic (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Slovak (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Spanish (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Swedish/Finn (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Swiss F/G (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G
79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Turkish (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Turkish (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
UK English (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G
79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
US International (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG)
Yugoslav/Latin (models 15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
8085 Productivity USB Keyboard
FRU#
CRU
US (models 32U)
89P8800
*
8085 Power Cords
FRU#
CRU
Power Cord (models 34S 34D A2S A2D D1S D1D E3S E3D 14S 14D 17S 17D 24S 24D 27S
27D A1U 15U 15F 23U 24U 31U 32U 33U 33F A3U D2U D3U D4S D4D E1U 41U 42U 42S
42D 11U 13G 16G 18U 19U 1AU 1AS 1AD 1BU 21U 21F 21G 22G 35G 36G 71G 72G 73G
74G 75G 76G 77G 79G 7AG 7BG 7CG C1U C2U C3U C4U C5U C6U C7U A4U A5S A5D
B1U B2S B2D D5U 7DG C8U C9U CAU B3U E4G 1CU 1DU 1DF 28U 37U 51U 51F 51G
52G 53U 7EG 7FG 7GG 7HG CBU CDU E8S 38S)
6952301
*
Chapter 11. FRU lists 153
8085 Power Cords
FRU#
CRU
Power Cord (EMEA, ANZ, ASEAN Eng, Korea) (models15G 13G 16G 21G 22G 35G 36G
71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG
7HG)
13F9978
*
Power Cord (EMEA, ANZ, ASEAN Eng, HK Eng) (models15G 13G 16G 21G 22G 35G 36G
71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG
7HG)
14F0032
*
Power Cord (EMEA) (models15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G
77G 78G 79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
13F9996
14F0068
*
*
Power Cord (EMEA, LA) (models 34S 34D 34Y A2S A2D A2Y D1S D1D D1Y E3S E3D E3Y
14S 14D 14Y 17S 17D 17Y 24S 24D 24Y 27S 27D 27Y 15G D4S D4D D4Y 42S 42D 42Y 13G
16G 1AS 1AD 1AY 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG
7CG A5S A5D A5Y B2S B2D B2Y 7DG E4G 51G 52G 7EG 7FG 7GG 7HG E8S 38S)
Power Cord (APU) (models 34Y A2Y D1Y E3Y 14Y 17Y 24Y 27Y D4Y 42Y 1AY A5Y B2Y)
Power Cord (Japan) (models A6J A7J A8J B4J B5J B6J 1EJ 1FJ 1GJ 29J 2AJ 2BJ E9J EAJ EBJ)
36L8879
1838576
14F0086
*
*
*
Power Cord (EMEA) (models15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G
77G 78G 79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
Power Cord (EMEA, ANZ, ASEAN Eng) (models15G 13G 16G 21G 22G 35G 36G 71G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
14F0014
14F0050
*
*
Power Cord (EMEA) (models15G 13G 16G 21G 22G 35G 36G 71G 72G 73G 74G 75G 76G
77G 78G 79G 7AG 7BG 7CG 7DG E4G 51G 52G 7EG 7FG 7GG 7HG)
154 Hardware Maintenance Manual
Machine Type 8126
2
1
3
4
11
7
6
5
10
9
8
Item #
8126 FRUs
FRU#
CRU
1
2
3
Chassis assembly (all models)
74P2256
74P2257
40Y8801
N
*
Bezel and shield kit (all models)
CD-ROM Drive 48X - Black w/o jack & vol (models 41C 11C D3A
D3Q D3T D4V E1A E1Q E1T E2A E2Q E2T 12V 13A 13Q 13T 21A
21Q 21T 31A 31Q 31T)
**
3
3
3
3
CD-ROM Drive 48X - Black w/o jack & vol (models 41C 11C D3A
D3Q D3T D4V E1A E1Q E1T E2A E2Q E2T 12V 13A 13Q 13T 21A
21Q 21T 31A 31Q 31T)
40Y8805
40Y8807
40Y8813
40Y8929
**
**
**
**
CD-ROM Drive 48X - Black w/o jack & vol (models 41C 11C D3A
D3Q D3T D4V E1A E1Q E1T E2A E2Q E2T 12V 13A 13Q 13T 21A
21Q 21T 31A 31Q 31T)
CD-ROM Drive 48X - Black w/o jack & vol (models 41C 11C D3A
D3Q D3T D4V E1A E1Q E1T E2A E2Q E2T 12V 13A 13Q 13T 21A
21Q 21T 31A 31Q 31T)
CD-ROM Drive 48X - Black w/o jack & vol (models 41C 11C D3A
D3Q D3T D4V E1A E1Q E1T E2A E2Q E2T 12V 13A 13Q 13T 21A
21Q 21T 31A 31Q 31T)
Chapter 11. FRU lists 155
Item #
8126 FRUs
FRU#
CRU
4
Diskette drive, 3.5 1.44 MB (models D1C D2C A1C A2C D3A D3Q
D3T D4V E1A E1Q E1T E2A E2Q E2T 12V 13A 13Q 13T 21A 21Q 21T
31A 31Q 31T)
40Y9107
**
4
4
5
Diskette drive, 3.5 1.44 MB (models D1C D2C A1C A2C D3A D3Q
D3T D4V E1A E1Q E1T E2A E2Q E2T 12V 13A 13Q 13T 21A 21Q 21T
31A 31Q 31T)
40Y8899
40Y9105
40Y8757
**
**
**
Diskette drive, 3.5 1.44 MB (models D1C D2C A1C A2C D3A D3Q
D3T D4V E1A E1Q E1T E2A E2Q E2T 12V 13A 13Q 13T 21A 21Q 21T
31A 31Q 31T)
Hard disk drive, 40 GB EIDE (models D1C D2C 41C 11C A1C A2C
D3A D3Q D3T D4V E1A E1Q E1T E2A E2Q E2T 12V 13A 13Q 13T
21A 21Q 21T 31A 31Q 31T)
6
7
Speaker Asm. Soldered Terminals (all models)
00N5151
31P9120
*
*
128 MB SDRAM PC2700 (models D1C D2C 41C 11C A1C A2C D3A
D3Q D3T E1A E1Q E1T)
7
256 MB SDRAM PC2700 (models D4V E2A E2Q E2T 12V 13A 13Q
13T)
31P9121
*
7
8
8
256 MB SDRAM PC32 (models 21A 21Q 21T 31A 31Q 31T)
System board, 10/100 E-net, (models 12V 31A 31Q 31T)
73P2683
19R0703
39J7965
*
**
**
System board, (10/100 Enet) w/ video buffer -- optional to 19R0703
(models 12V 31A 31Q 31T)
8
8
System board, (10/100 Enet) w/ video buffer -- optional to 19R0703
(models 12V 31A 31Q 31T)
41D0948
19R0837
**
**
System board, 10/100 E-net, no AGP (models D1C D2C 41C 11C A1C
A2C D3A D3Q D3T D4V E1A E1Q E1T E2A E2Q E2T 13A 13Q 13T
21A 21Q 21T)
8
8
System board, (10/100 Enet) w/ video buffer, no AGP -- optional to
19R0837 (models D1C D2C 41C 11C A1C A2C D3A D3Q D3T D4V
E1A E1Q E1T E2A E2Q E2T 13A 13Q 13T 21A 21Q 21T)
39J7966
**
**
System board, (10/100 Enet) w/ video buffer, no AGP -- optional to
19R0837 (models D1C D2C 41C 11C A1C A2C D3A D3Q D3T D4V
E1A E1Q E1T E2A E2Q E2T 13A 13Q 13T 21A 21Q 21T)
41D0949
9
9
Intel P4 2.6 GHz (models 41C)
73P0574
19R2302
13R8907
19R0780
19R0419
29R6989
29R6990
19R0294
19R0296
32P4004
**
**
**
**
**
**
**
**
**
*
Intel P4 2.8 GHz (models 11C 13A 13Q 13T)
Intel Celeron 2.6 GHz (models D1C D2C)
9
9
Intel Celeron 2.4 GHz (models A1C A2C)
9
Intel Prescott Celeron 2.66 GHz (models D3A D3Q D3T D4V)
Intel Prescott Celeron 2.93 GHz (models E1A E1Q E1T E2A E2Q E2T)
Intel Prescott Celeron 3.06 GHz (models)
9
9
9
Intel Prescott 3.0 GHz (models 21A 21Q 21T)
Intel Prescott 3.2 GHz (models 31A 31Q 31T)
9
10
Heat sink and fan, Northwood <3.0GHZ (models D1C D2C 41C 11C
13A 13Q 13T)
10
Heat sink and fan, Northwood >=3.0 GHZ and all Prescott (models
A1C A2C D3A D3Q D3T D4V 12V 21A 21Q 21T 31A 31Q 31T)
13R9195
*
156 Hardware Maintenance Manual
Item #
8126 FRUs
FRU#
CRU
10
Heat sink and fan, Northwood >=3.0 GHZ and all Prescott, Dual Heat
Pipe -- optional to 13R9195 (models A1C A2C D3A D3Q D3T D4V
12V 21A 21Q 21T 31A 31Q 31T)
13N2951
*
11
11
230W Power Supply (models D3A D3T E1A E1T E2A E2T 13A 13T
21A 21T 31A 31T)
74P4300
74P4301
N
N
230W Power Supply - AcBel China version (models D1C D2C 41C
11C A1C A2C D3Q D4V E1Q E2Q 12V 13Q 21Q 31Q)
Chapter 11. FRU lists 157
The FRUs listed in the following table are not illustrated.
8126 FRUs
FRU#
CRU
**
**
**
**
**
**
**
*
Cable, Diskette drive (all models)
59P8568
75H9219
37L4525
37L5098
89P8137
49P1754
49P1933
09N6708
49P3386
09N6709
49P3387
74P2254
88P5927
26K1216
88P8585
33F8354
89P5089
Cable, audio (all models)
Cable, IDE (ATA66 1 drop) (all models)
Cable, IDE (ATA66 2 drop) (all models)
Dual USB 1.1 cable (top channel) (all models)
SPDIF Card assembly (all models)
Audio cable assembly (ATA) (all models)
Front panel label kit (all models)
Access panel (all models)
*
Cable, power/LED (all models)
**
*
Screw kit (all models)
Bracket, second hardfile mount & 6-32 screw (all models)
Cable, serial ATA (all models)
**
**
**
**
**
*
Planar shield (all models)
System Fan (includes bracket) -- =>3.0GHz (models 21A 21Q 21T 31A 31Q 31T)
Battery, 3.0 V (all models)
Mouse, optical wheel (models D1C D2C 41C 11C A1C A2C D3A D3Q D3T D4V E1A E1Q
E1T E2A E2Q E2T 12V 13A 13Q 13T 21A 21Q 21T 31A 31Q 31T)
RJ11 connector adapter (Spain, Ireland) (All ″G″ models)
RJ11 connector adapter (Austria) (All ″G″ models)
RJ11 connector adapter (Belgium) (All ″G″ models)
RJ11 connector adapter (Denmark) (All ″G″ models)
RJ11 connector adapter (Norway, Finland) (All ″G″ models)
RJ11 connector adapter (France) (All ″G″ models)
RJ11 connector adapter (Germany) (All ″G″ models)
RJ11 connector adapter (UK, NZ, HK) (All ″G″, ″M″, ″B″, ″H″ models)
RJ11 connector adapter (Italy) (All ″G″ models)
60H6043
60H6045
60H6046
60H6047
60H6048
60H6049
60H6050
60H6051
60H6052
60H6053
60H6054
60H6055
*
*
*
*
*
*
*
*
*
*
*
*
RJ11 connector adapter (Netherlands) (All ″G″ models)
RJ11 connector adapter (Sweden) (All ″G″ models)
RJ11 connector adapter (Switzerland) (All ″G″ models)
8126 Windows XP Home Recovery CDs
US/UK/AP/TH (models D3A D3Q D3T E1A E1Q E1T)
Simplified Chinese (models D2C A2C)
FRU#
39J6250
30R4777
CRU
*
*
8126 Windows XP Pro Recovery CDs
US/UK/AP/TH (models E2A E2Q E2T 13A 13Q 13T 21A 21Q 21T 31A 31Q 31T)
Simplified Chinese (models D4V 12V)
FRU#
39J6414
30R4820
CRU
*
*
158 Hardware Maintenance Manual
8126 Keyboards (Standard PS/2 Black)
FRU#
CRU
US English (models D1C D2C 41C 11C A1C A2C D3A D3Q E1A E1Q E2A E2Q 13A 13Q
21A 21Q 31A 31Q)
89P8300
*
Chinese/US (models D4V 12V)
89P8306
89P8334
*
*
Thailand (models D3T E1T E2T 13T 21T 31T)
8126 Power Cords
FRU#
CRU
Power Cord (models D3A D3T D4V E1A E1T E2A E2T 12V 13A 13T 21A 21T
31A 31T)
6952301
*
Power Cord (China, HK) (models D1C D2C 41C 11C A1C A2C)
Power Cord (India) (models D3Q E1Q E2Q 13Q 21Q 31Q)
02K0545
49P2078
*
*
Machine Type 8147
Item #
8147 FRUs
FRU#
59P8547
CRU
**
ꢀ1ꢁ Side cover assembly (all models)
Chapter 11. FRU lists 159
Item #
8147 FRUs
FRU#
CRU
**
ꢀ2ꢁ ″L″ Cover assembly (all models)
ꢀ3ꢁ Front Bezel assembly (all models)
ꢀ4ꢁ Bezel trim/label kit (all models)
59P8546
59P8544
49P1900
40Y8801
**
**
ꢀ5ꢁ CD-ROM Drive 48X (Black) - w/o volume ctrl and headphone jack (models 11U
*
13U 21U 31U D1U 34U 24U 15U 15F 36U 36F)
ꢀ5ꢁ CD-ROM Drive 48X (Black) - w/o volume ctrl and headphone jack (models 11U
40Y8805
40Y8807
40Y8813
40Y8929
*
*
*
*
13U 21U 31U D1U 34U 24U 15U 15F 36U 36F)
ꢀ5ꢁ CD-ROM Drive 48X (Black) - w/o volume ctrl and headphone jack (models 11U
13U 21U 31U D1U 34U 24U 15U 15F 36U 36F)
ꢀ5ꢁ CD-ROM Drive 48X (Black) - w/o volume ctrl and headphone jack (models 11U
13U 21U 31U D1U 34U 24U 15U 15F 36U 36F)
ꢀ5ꢁ CD-ROM Drive 48X (Black) - w/o volume ctrl and headphone jack (models 11U
13U 21U 31U D1U 34U 24U 15U 15F 36U 36F)
ꢀ5ꢁ CD-RW Drive (48X/32X/48X) (models 12U 22U 32U 25U)
40Y8811
40Y8901
40Y8781
*
*
*
ꢀ5ꢁ CD-RW Drive (48X/32X/48X) (models 12U 22U 32U 25U)
ꢀ5ꢁ DVD-ROM/CD-RW Combo Drive (48x\32x\48x\16x) (models 23U 33U 14U 35U
35F)
ꢀ5ꢁ DVD-ROM/CD-RW Combo Drive (48x\32x\48x\16x) (models 23U 33U 14U 35U
40Y8903
40Y9107
40Y8899
40Y9105
40Y8757
*
*
*
*
*
35F)
ꢀ6ꢁ Diskette drive, 3.5 1.44MB (models D1U 13U 23U 33U 11U 12U 21U 22U 31U 32U
34U 14U 24U 25U 15U 15F 35U 35F 36U 36F)
ꢀ6ꢁ Diskette drive, 3.5 1.44MB (models D1U 13U 23U 33U 11U 12U 21U 22U 31U 32U
34U 14U 24U 25U 15U 15F 35U 35F 36U 36F)
ꢀ6ꢁ Diskette drive, 3.5 1.44MB (models D1U 13U 23U 33U 11U 12U 21U 22U 31U 32U
34U 14U 24U 25U 15U 15F 35U 35F 36U 36F)
ꢀ7ꢁ Hard disk drive, 40GB EIDE (models D1U 13U 11U 12U 21U 22U 31U 32U 34U
14U 24U 25U 15U 15F 36U 36F)
ꢀ7ꢁ Hard disk drive, 80GB EIDE (models 23U 33U 35U 35F)
40Y8758
19R0703
*
ꢀ8ꢁ System board, 10/100 E-net (models 12U 32U 22U 23U 31U 33U CDU CEU CFU
**
CTO-U 21U 34U CGU 24U 25U 35U 35F 36U 36F)
ꢀ8ꢁ System board, (10/100 Enet) w/ video buffer -- optional to 19R0703 (models 12U
32U 22U 23U 31U 33U CDU CEU CFU CTO-U 21U 34U CGU 24U 25U 35U 35F
36U 36F)
39J7965
**
**
ꢀ8ꢁ System board, (10/100 Enet) w/ video buffer -- optional to 19R0703 (models 12U
32U 22U 23U 31U 33U CDU CEU CFU CTO-U 21U 34U CGU 24U 25U 35U 35F
36U 36F)
41D0948
ꢀ8ꢁ System board, 10/100 E-net, no AGP (models 11U 13U D1U CAU CBU CCU 14U
19R0837
39J7966
41D0949
**
**
**
15U 15F)
ꢀ8ꢁ System board, (10/100 Enet) w/ video buffer, no AGP -- optional to 19R0837
(models 11U 13U D1U CAU CBU CCU 14U 15U 15F)
ꢀ8ꢁ System board, (10/100 Enet) w/ video buffer, no AGP -- optional to 19R0837
(models 11U 13U D1U CAU CBU CCU 14U 15U 15F)
ꢀ9ꢁ 256 MB SDRAM (models D1U 13U 11U 14U 15U 15F)
31P9121
73P2683
*
*
ꢀ9ꢁ 256 MB SDRAM (models 23U 33U 12U 22U 31U 32U 21U 34U 24U 25U 35U 35F
36U 36F)
ꢀ10ꢁ Intel P4 2.6 GHz (models D1U CAU)
73P0574
19R2302
* *
* *
ꢀ10ꢁ Intel P4 2.8 GHz (models 13U CBU)
160 Hardware Maintenance Manual
Item #
8147 FRUs
FRU#
CRU
* *
ꢀ10ꢁ Intel P4 2.8 GHz Prescott (models CCU 11U 14U 15U 15F)
ꢀ10ꢁ Intel P4 2.8 GHz Prescott (models 12U CDU)
19R0423
19R0292
19R0294
19R0296
29R6991
32P4004
13R9195
* *
ꢀ10ꢁ Intel P4 3.0 GHz Prescott (models 22U 23U CEU 21U 24U 25U 35U 35F 36U 36F)
ꢀ10ꢁ Intel P4 3.2 GHz Prescott (models 31U 32U 33U CFU 34U)
ꢀ10ꢁ Intel P4 3.4 GHz Prescott (models CGU)
* *
* *
* *
ꢀ11ꢁ Heat sink and fan, Northwood <3.0GHz (models D1U CAU 13U CBU)
* *
ꢀ11ꢁ Heat sink and fan, Northwood >=3.0 GHZ and all Prescott (models CCU CDU
* *
23U CEU 11U 22U 33U CFU 21U 34U CGU 14U 24U 25U 15U 15F 35U 35F 36U
36F)
ꢀ11ꢁ Heat sink and fan,Northwood >=3.0 GHZ and all Prescott, Dual Heat Pipe --
optional to 13R9195 (models CCU CDU 23U CEU 11U 22U 33U CFU 21U 34U
CGU 14U 24U 25U 15U 15F 35U 35F 36U 36F)
13N2951
74P4300
59P8542
* *
N
**
ꢀ12ꢁ Power supply, AcBel PFC, 230W (models D1U 13U 23U 33U CAU CBU CCU CDU
CEU CFU 11U 12U 21U 22U 31U 32U 34U CGU 14U 24U 25U 15U 15F 35U 35F
36U 36F)
ꢀ13ꢁ Chassis assembly (all models)
The FRUs listed in the following tables are not illustrated.
8147 FRUs
Front bezel release kit (all models)
FRU#
CRU
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
*
25P0069
59P8564
75H9219
19K5548
03K9655
32P4743
25P0068
22P4447
49P1750
49P1933
49P4365
59P8543
59P8549
59P8545
59P8548
59P8571
59P8572
59P8568
59P8584
33F8354
89P5089
Retainer, Adapter Cards (all models)
Cable, audio (all models)
5.25 EMC shield (all models)
Rubber foot (all models)
Universal adapter bracket (all models)
Bezel blanks kit (all models)
80 mm fan assembly (models with 3.06 GHz microprocessor or greater)
2 audio front panel (models23U 33U 35U 35F)
Cable, audio assembly (all models)
Cable, dual USB 2.0 (all models)
Hard disk drive bracket assembly (all models)
Hard disk drive tray (all models)
Power switch assembly (all models)
Bezel, Diskette drive (all models)
Cable, 2 drop (close spacing) ATA 66/100 w/pull tabs (all models)
Cable, 2 drop** (large spacing) ATA 66/100 w/pull tabs (all models)
Cable, Diskette drive (all models)
*
*
Cable clip (all models)
*
Battery, 3.0 V (all models)
**
*
Mouse, optical wheel (models D1U 13U 23U 33U 11U 12U 21U 22U 31U 32U 34U 14U 24U
25U 15U 15F 35U 35F 36U 36F)
64MB, Nvidia GeForce MX 440 (VGA) ATX (models 23U 33U 35U 35F)
73P0715
*
Chapter 11. FRU lists 161
8147 FRUs
System board EMC shield kit (all models)
FRU#
CRU
89P4761
89P6740
13R9195
09N5764
60H6043
60H6045
60H6046
60H6047
60H6048
60H6049
60H6050
60H6051
60H6052
60H6053
60H6054
60H6055
**
**
**
**
*
Retention kit (all models)
Heatsink grease, Heat pipe (all models)
Misc. hardware kit (all models)
RJ11 connector adapter (Spain, Ireland) (All ″G″ models)
RJ11 connector adapter (Austria) (All ″G″ models)
RJ11 connector adapter (Belgium) (All ″G″ models)
RJ11 connector adapter (Denmark) (All ″G″ models)
RJ11 connector adapter (Norway, Finland) (All ″G″ models)
RJ11 connector adapter (France) (All ″G″ models)
RJ11 connector adapter (Germany) (All ″G″ models)
RJ11 connector adapter (UK, NZ, HK) (All ″G″, ″M″, ″B″, ″H″ models)
RJ11 connector adapter (Italy) (All ″G″ models)
RJ11 connector adapter (Netherlands) (All ″G″ models)
RJ11 connector adapter (Sweden) (All ″G″ models)
RJ11 connector adapter (Switzerland) (All ″G″ models)
*
*
*
*
*
*
*
*
*
*
*
8147 Windows XP Pro Recovery CDs
FRU#
CRU
US (models 11U 12U 21U 22U 31U 32U D1U 13U 23U 33U 34U 14U 24U 25U 15U 35U
36U)
39J6414
*
FR (models 15F 35F 36F)
39J6415
*
8147 Keyboards (Standard PS/2 Black)
FRU#
CRU
US English (models D1U 13U 23U 33U 11U 12U 21U 22U 31U 32U 34U 14U 24U 25U 15U
35U 36U)
89P8300
*
French Canadian 445 (models 15F 35F 36F)
French Canadian 58 (models 15F 35F 36F)
89P8311
89P8312
*
*
8147 Power Cords
FRU#
CRU
Power Cord (models D1U 13U 23U 33U CAU CBU CCU CDU CEU CFU 11U 12U 21U
22U 31U 32U 34U CGU 14U 24U 25U 15U 15F 35U 35F 36U 36F)
6952301
*
162 Hardware Maintenance Manual
Machine Type 8148
Item #
8148 FRUs
FRU#
CRU
**
ꢀ1ꢁ Side cover assembly (all models)
ꢀ2ꢁ ″L″ Cover assembly (all models)
ꢀ3ꢁ Front Bezel assembly (all models)
ꢀ4ꢁ Bezel trim/label kit (all models)
59P8547
59P8546
59P8544
49P1900
40Y8801
**
**
**
ꢀ5ꢁ CD-ROM Drive 48X (Black) - w/o volume ctrl and headphone jack (models A1U
D1U E1U 21U 31U A2U A3G B1G D2G E2G 41U 42U 13U 14G 15G 24G 34G 71G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 15U A4U A4G B2U D3U
7EG 7HG 7JG 7KG E3G 35U 51G 7RG 7UG 25U A5U A5F 18U 18F 29U 29F A6G
7YG 7ZG)
*
ꢀ5ꢁ CD-ROM Drive 48X (Black) - w/o volume ctrl and headphone jack (models A1U
D1U E1U 21U 31U A2U A3G B1G D2G E2G 41U 42U 13U 14G 15G 24G 34G 71G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 15U A4U A4G B2U D3U
7EG 7HG 7JG 7KG E3G 35U 51G 7RG 7UG 25U A5U A5F 18U 18F 29U 29F A6G
7YG 7ZG)
40Y8805
*
Chapter 11. FRU lists 163
Item #
8148 FRUs
FRU#
CRU
ꢀ5ꢁ CD-ROM Drive 48X (Black) - w/o volume ctrl and headphone jack (models A1U
D1U E1U 21U 31U A2U A3G B1G D2G E2G 41U 42U 13U 14G 15G 24G 34G 71G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 15U A4U A4G B2U D3U
7EG 7HG 7JG 7KG E3G 35U 51G 7RG 7UG 25U A5U A5F 18U 18F 29U 29F A6G
7YG 7ZG)
40Y8807
*
ꢀ5ꢁ CD-ROM Drive 48X (Black) - w/o volume ctrl and headphone jack (models A1U
D1U E1U 21U 31U A2U A3G B1G D2G E2G 41U 42U 13U 14G 15G 24G 34G 71G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 15U A4U A4G B2U D3U
7EG 7HG 7JG 7KG E3G 35U 51G 7RG 7UG 25U A5U A5F 18U 18F 29U 29F A6G
7YG 7ZG)
40Y8813
40Y8829
*
*
ꢀ5ꢁ CD-ROM Drive 48X (Black) - w/o volume ctrl and headphone jack (models A1U
D1U E1U 21U 31U A2U A3G B1G D2G E2G 41U 42U 13U 14G 15G 24G 34G 71G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 15U A4U A4G B2U D3U
7EG 7HG 7JG 7KG E3G 35U 51G 7RG 7UG 25U A5U A5F 18U 18F 29U 29F A6G
7YG 7ZG)
ꢀ5ꢁ DVD-ROM 16X/48X (Black) (models 7GG 7MG 7NG 7PG 7QG 7VG 7WG)
ꢀ5ꢁ CD-RW Drive (48X/32X/48X) (models 12U 22U 32U 26U 28U 28F)
ꢀ5ꢁ DVD-ROM/CD-RW Combo Drive (48x\32x\48x\16x) (models 23U 33U 16U)
ꢀ5ꢁ DVD-ROM/CD-RW Combo Drive (48x\32x\48x\16x) (models 23U 33U 16U)
40Y8811
40Y8901
40Y8781
40Y8903
40Y9107
*
*
*
*
*
ꢀ6ꢁ Diskette drive, 3.5 1.44MB (models A1U D1U E1U 12U 21U 22U 31U 32U A2U
A3G B1G D2G E2G 41U 42U 13U 14G 15G 23U 24G 33U 34G 71G 72G 73G 74G
75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 15U A4U A4G B2U D3U 7EG 7GG
7HG 7JG 7KG E3G 35U 51G 7MG 7NG 7PG 7QG 7RG 7UG 16U 25U 26U A5U
A5F 18U 18F 28U 28F 29U 29F A6G 7VG 7WG 7YG 7ZG)
ꢀ6ꢁ Diskette drive, 3.5 1.44MB (models A1U D1U E1U 12U 21U 22U 31U 32U A2U
A3G B1G D2G E2G 41U 42U 13U 14G 15G 23U 24G 33U 34G 71G 72G 73G 74G
75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 15U A4U A4G B2U D3U 7EG 7GG
7HG 7JG 7KG E3G 35U 51G 7MG 7NG 7PG 7QG 7RG 7UG 16U 25U 26U A5U
A5F 18U 18F 28U 28F 29U 29F A6G 7VG 7WG 7YG 7ZG)
40Y8899
40Y9105
40Y8757
*
*
*
ꢀ6ꢁ Diskette drive, 3.5 1.44MB (models A1U D1U E1U 12U 21U 22U 31U 32U A2U
A3G B1G D2G E2G 41U 42U 13U 14G 15G 23U 24G 33U 34G 71G 72G 73G 74G
75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 15U A4U A4G B2U D3U 7EG 7GG
7HG 7JG 7KG E3G 35U 51G 7MG 7NG 7PG 7QG 7RG 7UG 16U 25U 26U A5U
A5F 18U 18F 28U 28F 29U 29F A6G 7VG 7WG 7YG 7ZG)
7
Hard disk drive, 40GB EIDE (models A1U D1U E1U 12U 21U 22U 31U 32U A2U
A3G B1G D2G E2G 41U 42U 13U 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G
77G 78G 79G 7AG 7BG 7CG 7DG 15U A4U A4G B2U D3U 7EG 7GG 7HG 7JG
7KG E3G 35U 51G 7MG 7NG 7PG 7QG 7RG 7UG 16U 25U 26U A5U A5F 18U 18F
28U 28F 29U 29F A6G 7VG 7WG 7YG 7ZG)
ꢀ7ꢁ Hard disk drive, 80GB EIDE (models 23U 33U)
40Y8758
19R0703
*
ꢀ8ꢁ System board, 10/100 E-net (models 12U 31U 22U 32U 23U 33U CGU CHU CJU
**
21U 35U 51G CMU 25U 26U 28U 28F 29U 29F)
ꢀ8ꢁ System board, (10/100 Enet) w/ video buffer -- optional to 19R0703 (models 12U
39J7965
**
**
31U 22U 32U 23U 33U CGU CHU CJU 21U 35U 51G CMU 25U 26U 28U 28F 29U
29F)
ꢀ8ꢁ System board, (10/100 Enet) w/ video buffer -- optional to 19R0703 (models 12U
41D0948
31U 22U 32U 23U 33U CGU CHU CJU 21U 35U 51G CMU 25U 26U 28U 28F 29U
29F)
164 Hardware Maintenance Manual
Item #
8148 FRUs
FRU#
CRU
ꢀ8ꢁ System board, 10/100 E-net, no AGP (models A1U D1U E1U A2U A3G B1G D2G
E2G 41U 42U 13U 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G 78G 79G
7AG 7BG 7CG 7DG CAU CBU CCU CDU CEU CFU 15U A4U A4G B2U D3U 7EG
7GG 7HG 7JG 7KG E3G 7MG 7NG 7PG 7QG 7RG 7UG CKU CLU 16U A5U A5F
18U 18F A6G 7VG 7WG 7YG 7ZG)
19R0837
**
ꢀ8ꢁ System board, (10/100 Enet) w/ video buffer, no AGP -- optional to 19R0837
(models A1U D1U E1U A2U A3G B1G D2G E2G 41U 42U 13U 14G 15G 24G 34G
71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG CAU CBU CCU
CDU CEU CFU 15U A4U A4G B2U D3U 7EG 7GG 7HG 7JG 7KG E3G 7MG 7NG
7PG 7QG 7RG 7UG CKU CLU 16U A5U A5F 18U 18F A6G 7VG 7WG 7YG 7ZG)
39J7966
**
**
ꢀ8ꢁ System board, (10/100 Enet) w/ video buffer, no AGP -- optional to 19R0837
(models A1U D1U E1U A2U A3G B1G D2G E2G 41U 42U 13U 14G 15G 24G 34G
71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG CAU CBU CCU
CDU CEU CFU 15U A4U A4G B2U D3U 7EG 7GG 7HG 7JG 7KG E3G 7MG 7NG
7PG 7QG 7RG 7UG CKU CLU 16U A5U A5F 18U 18F A6G 7VG 7WG 7YG 7ZG)
41D0949
ꢀ9ꢁ 128 MB SDRAM (models A2U A3G B1G D2G E2G 41U 71G 73G 75G 77G 7EG)
31P9120
31P9121
*
*
ꢀ9ꢁ 256 MB SDRAM (models A1U D1U E1U 42U 13U 14G 15G 72G 74G 76G 78G 79G
7AG 7BG 15U A4U A4G B2U D3U 7GG 7HG 7JG 7KG E3G 7MG 7NG 7PG 7QG
7RG 16U A5U A5F 18U 18F A6G 7VG 7WG 7YG)
ꢀ9ꢁ 256 MB SDRAM (models 12U 22U 31U 32U 23U 24G 33U 34G 7CG 7DG 21U 35U
73P2683
*
51G 7UG 25U 26U 28U 28F 29U 29F 7ZG)
ꢀ10ꢁ Intel Celeron 2.4 GHz (models A1U A2U A3G 71G 72G CAU)
ꢀ10ꢁ Intel Celeron 2.6 GHz (models D1U CBU)
88P7699
13R8907
19R0780
19R0417
19R0419
19R0421
29R6989
29R6990
73P0574
19R2302
74P1631
19R0423
19R0292
19R0294
19R0296
29R6991
32P4004
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
* *
ꢀ10ꢁ Intel Celeron 2.4 GHz (models A4U A4G 7EG 7GG 7JG)
ꢀ10ꢁ Intel Celeron 2.53 GHz (models B1G 73G 74G B2U 7MG A5U A5F)
ꢀ10ꢁ Intel Celeron 2.66 GHz (models D2G 76G 75G D3U 7NG)
ꢀ10ꢁ Intel Celeron 2.8 GHz (models E1U E2G 77G 78G CCU 7PG 7VG)
ꢀ10ꢁ Intel Celeron 2.93 GHz (models E3G 7QG 7RG CKU)
ꢀ10ꢁ Intel Celeron 3.06 GHz (models CLU A6G 7YG 7WG)
ꢀ10ꢁ Intel P4 2.6 GHz (models 41U 42U CDU)
ꢀ10ꢁ Intel P4 2.8 GHz (models 13U 14G 7AG CEU 7HG)
ꢀ10ꢁ Intel P4 2.8 GHz (models 79G)
ꢀ10ꢁ Intel P4 2.8 GHz (models 15G 7BG CFU 15U 7KG 16U 18U 18F)
ꢀ10ꢁ Intel P4 2.8 GHz (models 12U CGU 7ZG)
ꢀ10ꢁ Intel P4 3.0 GHz (models 22U 23U 24G 7CG CHU 21U 25U 26U 28U 28F 29U 29F)
ꢀ10ꢁ Intel P4 3.2 GHz (models 31U 32U 33U 34G 7DG CJU 35U)
ꢀ10ꢁ Intel P4 3.4 GHz (models 51G 7UG CMU)
ꢀ11ꢁ Heat sink and fan, Northwood <3.0 GHZ (models A1U A2U A3G 71G 72G CAU
D1U CBU 41U 42U CDU 13U 14G 7AG CEU 7HG 79G)
ꢀ11ꢁ Heat sink and fan, Northwood >=3.0 GHZ and all Prescott (models 12U 22U 31U
32U 15G 7BG CFU 23U 24G 7CG CHU 33U 34G 7DG CJU CGU 15U B1G 73G 74G
D2G 76G E2G 77G 78G CCU 75G A4U A4G CKU 7EG 7GG 7JG B2U CLU D3U
CMU 7KG 35U 51G 7UG 7MG 7NG 7PG 21U 16U 25U 26U 16U A5U A5F 18U 18F
28U 28F 29U 29F A6G 7YG 7WG 7VG 7ZG)
13R9195
* *
Chapter 11. FRU lists 165
Item #
8148 FRUs
FRU#
CRU
ꢀ11ꢁ Heat sink and fan, Northwood >=3.0 GHZ and all Prescott, Dual Heat Pipe --
optional to 13R9195 (models 12U 22U 31U 32U 15G 7BG CFU 23U 24G 7CG CHU
33U 34G 7DG CJU CGU 15U B1G 73G 74G D2G 76G E2G 77G 78G CCU 75G A4U
A4G CKU 7EG 7GG 7JG B2U CLU D3U CMU 7KG 35U 51G 7UG 7MG 7NG 7PG
21U 16U 25U 26U 16U A5U A5F 18U 18F 28U 28F 29U 29F A6G 7YG 7WG 7VG
7ZG)
13N2951
* *
ꢀ12ꢁ Power supply, AcBel PFC, 230W (models A1U D1U E1U 12U 21U 22U 31U 32U
A2U A3G B1G D2G E2G 41U 42U 13U 14G 15G 23U 24G 33U 34G 71G 72G 73G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG CAU CBU CCU CDU CEU CFU
CGU CHU CJU 15U A4U A4G B2U D3U 7EG 7GG 7HG 7JG CKU CLU CMU 7KG
E3G 35U 51G 7MG 7NG 7PG 7QG 7RG 7UG 16U 25U 26U A5U A5F 18U 18F 28U
28F 29U 29F A6G 7VG 7WG 7YG 7ZG)
74P4300
59P8542
N
**
ꢀ13ꢁ Chassis assembly (all models)
The FRUs listed in the following table are not illustrated.
8148 FRUs
Front bezel release kit (all models)
FRU#
CRU
**
**
**
**
**
**
**
**
**
**
**
**
**
**
**
*
25P0069
59P8564
75H9219
19K5548
03K9655
32P4743
25P0068
22P4447
49P1750
49P1933
49P4365
59P8543
59P8549
59P8545
59P8548
59P8571
59P8572
59P8568
33F8354
24P0383
89P5089
Retainer, Adapter Cards (all models)
Cable, audio (all models)
5.25 EMC shield (all models)
Rubber foot (all models)
Universal adapter bracket (all models)
Bezel blanks kit (all models)
80 mm fan assembly (models with 3.06 GHz microprocessor or greater)
2 audio front panel (models 12U 13U 23U 33U 7HG)
Cable, audio assembly (all models)
Cable, dual USB 2.0 (all models)
Hard disk drive bracket assembly (all models)
Hard disk drive tray (all models)
Power switch assembly (all models)
Bezel, Diskette drive (all models)
Cable, 2 drop (close spacing) ATA 66/100 w/pull tabs (all models)
Cable, 2 drop** (large spacing) ATA 66/100 w/pull tabs (all models)
Cable, Diskette drive (all models)
*
*
Battery, 3.0 V (all models)
**
*
Mouse, PS/2 2BUTTON (Black) (models A2U 41U)
Mouse, optical wheel (models A1U D1U E1U 12U 21U 22U 31U 32U 42U 13U 23U 33U
A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG
7CG 7DG 15U A4U A4G B2U D3U 7EG 7GG 7HG 7JG 7KG E3G 35U 51G 7MG 7NG 7PG
7QG 7RG 7UG 16U 25U 26U A5U A5F 18U 18F 28U 28F 29U 29F A6G 7VG 7WG 7YG
7ZG)
*
Cable clip (all models)
59P8584
89P4761
89P6740
*
System board EMC shield kit (all models)
Retention kit (all models)
**
**
166 Hardware Maintenance Manual
8148 FRUs
FRU#
CRU
Heatsink grease, Heat pipe (all models)
Misc. hardware kit (all models)
13R9195
09N5764
60H6043
60H6045
60H6046
60H6047
60H6048
60H6049
60H6050
60H6051
60H6052
60H6053
60H6054
60H6055
**
**
*
RJ11 connector adapter (Spain, Ireland) (All ″G″ models)
RJ11 connector adapter (Austria) (All ″G″ models)
RJ11 connector adapter (Belgium) (All ″G″ models)
RJ11 connector adapter (Denmark) (All ″G″ models)
RJ11 connector adapter (Norway, Finland) (All ″G″ models)
RJ11 connector adapter (France) (All ″G″ models)
RJ11 connector adapter (Germany) (All ″G″ models)
RJ11 connector adapter (UK, NZ, HK) (All ″G″, ″M″, ″B″, ″H″ models)
RJ11 connector adapter (Italy) (All ″G″ models)
*
*
*
*
*
*
*
*
RJ11 connector adapter (Netherlands) (All ″G″ models)
RJ11 connector adapter (Sweden) (All ″G″ models)
RJ11 connector adapter (Switzerland) (All ″G″ models)
*
*
*
8148 Windows XP Home Recovery CDs
FRU#
CRU
US (models A2U 41U 71G 73G 75G 77G 7EG 7GG 7HG 7KG 7MG 7NG 7PG 7QG
7WG)
39J6250
*
FR (models 71G 73G 75G 77G 7EG 7GG 7HG 7KG 7MG 7NG 7PG 7QG 7WG)
GR (models 71G 73G 75G 77G 7EG 7GG 7HG 7KG 7MG 7NG 7PG 7QG 7WG)
IT (models 71G 73G 75G 77G 7EG 7GG 7HG 7KG 7MG 7NG 7PG 7QG 7WG)
DK (models 71G 73G 75G 77G 7EG 7GG 7HG 7KG 7MG 7NG 7PG 7QG 7WG)
NL (models 71G 73G 75G 77G 7EG 7GG 7HG 7KG 7MG 7NG 7PG 7QG 7WG)
AE (models 71G 73G 75G 77G 7EG 7GG 7HG 7KG 7MG 7NG 7PG 7QG 7WG)
SV (models 71G 73G 75G 77G 7EG 7GG 7HG 7KG 7MG 7NG 7PG 7QG 7WG)
HE (models 71G 73G 75G 77G 7EG 7GG 7HG 7KG 7MG 7NG 7PG 7QG 7WG)
FI (models 71G 73G 75G 77G 7EG 7GG 7HG 7KG 7MG 7NG 7PG 7QG 7WG)
NO (models 71G 73G 75G 77G 7EG 7GG 7HG 7KG 7MG 7NG 7PG 7QG 7WG)
PL (models 71G 73G 75G 77G 7EG 7GG 7HG 7KG 7MG 7NG 7PG 7QG 7WG)
PO (models 71G 73G 75G 77G 7EG 7GG 7HG 7KG 7MG 7NG 7PG 7QG 7WG)
RU (models 71G 73G 75G 77G 7EG 7GG 7HG 7KG 7MG 7NG 7PG 7QG 7WG)
RE (models 71G 73G 75G 77G 7EG 7GG 7HG 7KG 7MG 7NG 7PG 7QG 7WG)
HU (models 71G 73G 75G 77G 7EG 7GG 7HG 7KG 7MG 7NG 7PG 7QG 7WG)
CZ (models 71G 73G 75G 77G 7EG 7GG 7HG 7KG 7MG 7NG 7PG 7QG 7WG)
TR (models 71G 73G 75G 77G 7EG 7GG 7HG 7KG 7MG 7NG 7PG 7QG 7WG)
GK (models 71G 73G 75G 77G 7EG 7GG 7HG 7KG 7MG 7NG 7PG 7QG 7WG)
39J6251
39J6252
39J6254
39J6257
39J6260
39J6264
39J6256
39J6261
39J6258
39J6259
39J6262
39J6268
41D1948
41D1947
39J6267
39J6263
39J6266
39J6269
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
8148 Windows XP Pro Recovery CDs
FRU #
CRU
US (models A1U D1U E1U 12U 21U 22U 31U 32U A3G B1G D2G E2G 42U 13U
14G 15G 23U 24G 33U 34G 72G 74G 76G 78G 79G 7AG 7BG 7CG 7DG 15U A4U
A4G B2U D3U 7JG E3G 35U 51G 7RG 7UG 16U 25U 26U A5U 18U 28U 29U
A6G 7VG 7YG 7ZG)
39J6414
*
Chapter 11. FRU lists 167
8148 Windows XP Pro Recovery CDs
FRU #
CRU
FR (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A5F 18F 28F 29F A6G 7VG 7YG
7ZG)
39J6415
*
GR (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
39J6416
39J6418
39J6417
39J6421
39J6424
39J6428
39J6420
39J6425
39J6422
39J6423
39J6426
39J6432
41D1950
41D1949
39J6431
39J6427
39J6430
39J6433
39J6434
39J7221
39J7222
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
IT (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
SP (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
DK (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
NL models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
AE (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
SV (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
HE (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
FI (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
NO (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
PL (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
PO (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
RU (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
RE (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
HU (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
CZ (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
TR (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
GK (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
SL (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G 79G 7AG
7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
Multilingual 1 (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G
79G 7AG 7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
Multilingual 2 (models A3G B1G D2G E2G 14G 15G 24G 34G 72G 74G 76G 78G
79G 7AG 7BG 7CG 7DG A4G 7JG E3G 51G 7RG 7UG A6G 7VG 7YG 7ZG)
168 Hardware Maintenance Manual
Keyboard (Preferred Pro Fullsize, PS/2, Stealth Black)
FRU#
CRU
US English (models A1U D1U E1U 12U 21U 22U 31U 32U A2U A3G B1G D2G E2G 41U
42U 13U 14G 15G 23U 24G 33U 34G 71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG
7CG 7DG 15U A4U A4G B2U D3U 7EG 7GG 7HG 7JG 7KG E3G 35U 51G 7MG 7NG 7PG
7QG 7RG 7UG 16U 25U 26U A5U 18U 28U 29U A6G 7VG 7WG 7YG 7ZG)
89P8300
*
Arabic (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G 78G
79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG 7RG
7UG A6G 7VG 7WG 7YG 7ZG)
89P8301
89P8302
89P8305
89P8307
89P8308
89P8309
89P8310
*
*
*
*
*
*
*
Belgian/French (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G
77G 78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG
7QG 7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Bulgarian (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG
7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Czech (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G 78G
79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG 7RG
7UG A6G 7VG 7WG 7YG 7ZG)
Danish (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG
7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Dutch (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G 78G
79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG 7RG
7UG A6G 7VG 7WG 7YG 7ZG)
French (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG
7RG 7UG A6G 7VG 7WG 7YG 7ZG)
French Canadian 445 (models A5F 18F 28F 29F)
French Canadian 58 (models A5F 18F 28F 29F)
89P8311
89P8312
89P8313
*
*
*
German (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG
7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Greek (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G 78G
79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG 7RG
7UG A6G 7VG 7WG 7YG 7ZG)
89P8314
89P8303
89P8315
89P8316
89P8317
89P8318
89P8319
*
*
*
*
*
*
*
Belgian/UK (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G
77G 78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG
7QG 7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Hebrew (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG
7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Hungarian (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG
7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Iceland (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG
7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Italian 141 (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG
7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Italian 142 (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG
7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Chapter 11. FRU lists 169
Keyboard (Preferred Pro Fullsize, PS/2, Stealth Black)
FRU#
CRU
Norwegian (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG
7RG 7UG A6G 7VG 7WG 7YG 7ZG)
89P8323
*
Polish (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G 78G
79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG 7RG
7UG A6G 7VG 7WG 7YG 7ZG)
89P8324
89P8325
89P8326
89P8327
89P8328
89P8329
89P8330
89P8331
89P8332
89P8333
89P8335
89P8336
89P8337
89P8338
89P8339
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Portuguese (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG
7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Romanian (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG
7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Russian (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG
7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Russian/Cyrillic (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G
76G 77G 78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG
7PG 7QG 7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Serbian/Cyrillic (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G
76G 77G 78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG
7PG 7QG 7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Slovak (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G 78G
79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG 7RG
7UG A6G 7VG 7WG 7YG 7ZG)
Spanish (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG
7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Swedish/Finn (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G
77G 78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG
7QG 7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Swiss F/G (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG
7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Turkish 440 (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G
77G 78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG
7QG 7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Turkish 179 (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G
77G 78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG
7QG 7RG 7UG A6G 7VG 7WG 7YG 7ZG)
UK English (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G
77G 78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG
7QG 7RG 7UG A6G 7VG 7WG 7YG 7ZG)
US Euro (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G 77G
78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG
7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Yugoslav/Latin (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G 75G 76G
77G 78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG 7NG 7PG
7QG 7RG 7UG A6G 7VG 7WG 7YG 7ZG)
170 Hardware Maintenance Manual
8148 Power Cords
FRU#
CRU
Power Cord (models A1U D1U E1U 12U 21U 22U 31U 32U A2U A3G B1G D2G E2G 41U
42U 13U 14G 15G 23U 24G 33U 34G 71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG
7CG 7DG CAU CBU CCU CDU CEU CFU CGU CHU CJU 15U A4U A4G B2U D3U 7EG
7GG 7HG 7JG CKU CLU CMU 7KG E3G 35U 51G 7MG 7NG 7PG 7QG 7RG 7UG 16U
25U 26U A5U A5F 18U 18F 28U 28F 29U 29F A6G 7VG 7WG 7YG 7ZG)
6952301
*
Power Cord (EMEA, ANZ, ASEAN Eng, Korea) (models A3G B1G D2G E2G 14G 15G 24G
34G 71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG
7KG E3G 51G 7MG 7NG 7PG 7QG 7RG 7UG A6G 7VG 7WG 7YG 7ZG)
13F9978
14F0032
13F9996
14F0068
14F0086
14F0014
14F0050
*
*
*
*
*
*
*
Power Cord (EMEA, ANZ, ASEAN Eng, HK Eng) (models A3G B1G D2G E2G 14G 15G
24G 34G 71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG
7HG 7JG 7KG E3G 51G 7MG 7NG 7PG 7QG 7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Power Cord (EMEA) (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G
75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG
7NG 7PG 7QG 7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Power Cord (EMEA, LA) (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G
75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG
7NG 7PG 7QG 7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Power Cord (EMEA) (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G
75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG
7NG 7PG 7QG 7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Power Cord (EMEA, ANZ, ASEAN Eng) (models A3G B1G D2G E2G 14G 15G 24G 34G
71G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG
7KG E3G 51G 7MG 7NG 7PG 7QG 7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Power Cord (EMEA) (models A3G B1G D2G E2G 14G 15G 24G 34G 71G 72G 73G 74G
75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG A4G 7EG 7GG 7HG 7JG 7KG E3G 51G 7MG
7NG 7PG 7QG 7RG 7UG A6G 7VG 7WG 7YG 7ZG)
Chapter 11. FRU lists 171
Machine Type 8149
1
2
3
13
4
12
11
10
5
9
8
7
6
Item #
8149 FRUs
FRU#
CRU
**
1
2
Top cover assembly (all models)
88P5962
74P4300
230W Power Supply - AcBel PFC (models 11U 21U 31U 41U 14U
CAU CBU CCU CDU CEU CFU 33U CGU 24U)
N
2
230W Power Supply - AcBel PFC China (models A1S A1Y D1S D1Y
D2S D2Y E1S E1Y E2S E2P E2Y 41S 41P 41Y 42S 42P 42Y 11S 11P 11Y
12S 12Y 13S 13P 13Y 14S 14P 14Y 15S 15P 15Y 22S 22Y 23S 23P 23Y
32S 32P 32Y A2S A2Y B1S B1P B1Y E3S E3Y E4S E4Y E5S E5Y 25S
25Y 34S 34Y)
74P4301
N
3
4
Pivot lock, 5.25 DASD (all models)
09N5747
40Y8801
**
**
CD-ROM Drive 48X - Black w/o jack & vol (models 11U 21U 31U
A1S A1Y D1S D1Y D2S D2Y E1S E1Y E2S E2P E2Y 41U 41S 41P 41Y
11S 11P 11Y 12S 12Y 13S 13P 13Y 14U 14S 14P 14Y 15S 15P 15Y 22S
22Y 23S 23P 23Y 32S 32P 32Y A2S A2Y B1S B1P B1Y 33U 24U E3S
E3Y E4S E4Y E5S E5Y 25S 25Y 34S 34Y)
4
CD-ROM Drive 48X - Black w/o jack & vol (models 11U 21U 31U
A1S A1Y D1S D1Y D2S D2Y E1S E1Y E2S E2P E2Y 41U 41S 41P 41Y
11S 11P 11Y 12S 12Y 13S 13P 13Y 14U 14S 14P 14Y 15S 15P 15Y 22S
22Y 23S 23P 23Y 32S 32P 32Y A2S A2Y B1S B1P B1Y 33U 24U E3S
E3Y E4S E4Y E5S E5Y 25S 25Y 34S 34Y)
40Y8805
**
172 Hardware Maintenance Manual
Item #
8149 FRUs
FRU#
CRU
4
CD-ROM Drive 48X - Black w/o jack & vol (models 11U 21U 31U
A1S A1Y D1S D1Y D2S D2Y E1S E1Y E2S E2P E2Y 41U 41S 41P 41Y
11S 11P 11Y 12S 12Y 13S 13P 13Y 14U 14S 14P 14Y 15S 15P 15Y 22S
22Y 23S 23P 23Y 32S 32P 32Y A2S A2Y B1S B1P B1Y 33U 24U E3S
E3Y E4S E4Y E5S E5Y 25S 25Y 34S 34Y)
40Y8807
**
4
4
5
CD-ROM Drive 48X - Black w/o jack & vol (models 11U 21U 31U
A1S A1Y D1S D1Y D2S D2Y E1S E1Y E2S E2P E2Y 41U 41S 41P 41Y
11S 11P 11Y 12S 12Y 13S 13P 13Y 14U 14S 14P 14Y 15S 15P 15Y 22S
22Y 23S 23P 23Y 32S 32P 32Y A2S A2Y B1S B1P B1Y 33U 24U E3S
E3Y E4S E4Y E5S E5Y 25S 25Y 34S 34Y)
40Y8813
40Y8929
40Y8757
**
**
**
CD-ROM Drive 48X - Black w/o jack & vol (models 11U 21U 31U
A1S A1Y D1S D1Y D2S D2Y E1S E1Y E2S E2P E2Y 41U 41S 41P 41Y
11S 11P 11Y 12S 12Y 13S 13P 13Y 14U 14S 14P 14Y 15S 15P 15Y 22S
22Y 23S 23P 23Y 32S 32P 32Y A2S A2Y B1S B1P B1Y 33U 24U E3S
E3Y E4S E4Y E5S E5Y 25S 25Y 34S 34Y)
Hard disk drive, 40 GB EIDE (models 11U 21U 31U A1S A1Y D1S
D1Y D2S D2Y E1S E1Y E2S E2P E2Y 41U 41S 41P 41Y 42S 42P 42Y
11S 11P 11Y 14U 14S 14P 14Y A2S A2Y B1S B1P B1Y 33U 24U E3S
E3Y E4S E4Y E5S E5Y)
5
6
Hard disk drive, 80 GB EIDE (models 12S 12Y 13S 13P 13Y 15S 15P
15Y 22S 22Y 23S 23P 23Y 32S 32P 32Y 25S 25Y 34S 34Y)
40Y8758
40Y9107
**
**
Diskette drive, 3.5 1.44 MB (models 11U 21U 31U A1S A1Y D1S D1Y
D2S D2Y E1S E1Y E2S E2P E2Y 41U 41S 41P 41Y 42S 42P 42Y 11S 11P
11Y 12S 12Y 13S 13P 13Y 14U 14S 14P 14Y 15S 15P 15Y 22S 22Y 23S
23P 23Y 32S 32P 32Y A2S A2Y B1S B1P B1Y 33U 24U E3S E3Y E4S
E4Y E5S E5Y 25S 25Y 34S 34Y)
6
6
Diskette drive, 3.5 1.44 MB (models 11U 21U 31U A1S A1Y D1S D1Y
D2S D2Y E1S E1Y E2S E2P E2Y 41U 41S 41P 41Y 42S 42P 42Y 11S 11P
11Y 12S 12Y 13S 13P 13Y 14U 14S 14P 14Y 15S 15P 15Y 22S 22Y 23S
23P 23Y 32S 32P 32Y A2S A2Y B1S B1P B1Y 33U 24U E3S E3Y E4S
E4Y E5S E5Y 25S 25Y 34S 34Y)
40Y8899
40Y9105
**
**
Diskette drive, 3.5 1.44 MB (models 11U 21U 31U A1S A1Y D1S D1Y
D2S D2Y E1S E1Y E2S E2P E2Y 41U 41S 41P 41Y 42S 42P 42Y 11S 11P
11Y 12S 12Y 13S 13P 13Y 14U 14S 14P 14Y 15S 15P 15Y 22S 22Y 23S
23P 23Y 32S 32P 32Y A2S A2Y B1S B1P B1Y 33U 24U E3S E3Y E4S
E4Y E5S E5Y 25S 25Y 34S 34Y)
7
8
Speaker assembly (all models)
00N5151
09N5748
88P5963
31P9120
31P9121
*
**
**
*
Pivot lock, 3.5 Diskette drive (all models)
Chassis/top cover kit (all models)
9
10
10
128 MB SDRAM (models A1S A1Y D1S D1Y)
256 MB SDRAM (models 11U D2S D2Y E1S E1Y E2S E2P E2Y 41U
41S 41P 41Y 42S 42P 42Y 11S 11P 11Y 12S 12Y 13S 13P 13Y 14U 14S
14P 14Y 22S 22Y A2S A2Y B1S B1P B1Y E3S E3Y E4S E4Y E5S E5Y)
*
10
11
256 MB SDRAM (models 21U 31U 15S 15P 15Y 23S 23P 23Y 32S 32P
32Y 33U 24U 25S 25Y 34S 34Y)
73P2683
19R0703
*
System board, 10/100 E-net (models 21U 31U 12S 12Y 13S 13P 13Y
22S 22Y 23S 23P 23Y 32S 32P 32Y CDU CEU CFU CTO-U 33U CGU
24U)
**
11
System board, (10/100 Enet) w/ video buffer -- optional to 19R0703
(models 21U 31U 12S 12Y 13S 13P 13Y 22S 22Y 23S 23P 23Y 32S 32P
32Y CDU CEU CFU CTO-U 33U CGU 24U)
39J7965
**
Chapter 11. FRU lists 173
Item #
8149 FRUs
FRU#
CRU
11
System board, (10/100 Enet) w/ video buffer -- optional to 19R0703
(models 21U 31U 12S 12Y 13S 13P 13Y 22S 22Y 23S 23P 23Y 32S 32P
32Y CDU CEU CFU CTO-U 33U CGU 24U)
41D0948
**
11
11
System board, 10/100 E-net, no AGP (models 11U A1S A1Y D1S D1Y
D2S D2Y E1S E1Y E2S E2P E2Y 41U 41S 41P 41Y 42S 42P 42Y 11S 11P
11Y 14U 14S 14P 14Y 15S 15P 15Y CAU CBU CCU A2S A2Y B1S B1P
B1Y E3S E3Y E4S E4Y E5S E5Y 25S 25Y 34S 34Y)
19R0837
39J7966
**
**
System board, (10/100 Enet) w/ video buffer, no AGP -- optional to
19R0837 (models 11U A1S A1Y D1S D1Y D2S D2Y E1S E1Y E2S E2P
E2Y 41U 41S 41P 41Y 42S 42P 42Y 11S 11P 11Y 14U 14S 14P 14Y 15S
15P 15Y CAU CBU CCU A2S A2Y B1S B1P B1Y E3S E3Y E4S E4Y E5S
E5Y 25S 25Y 34S 34Y)
11
System board, (10/100 Enet) w/ video buffer, no AGP -- optional to
19R0837 (models 11U A1S A1Y D1S D1Y D2S D2Y E1S E1Y E2S E2P
E2Y 41U 41S 41P 41Y 42S 42P 42Y 11S 11P 11Y 14U 14S 14P 14Y 15S
15P 15Y CAU CBU CCU A2S A2Y B1S B1P B1Y E3S E3Y E4S E4Y E5S
E5Y 25S 25Y 34S 34Y)
41D0949
**
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
2.4GHz Celeron, (models A1S A1Y)
88P7699
13R8907
13R8963
19R0780
19R0417
19R0419
19R0421
29R6989
29R6990
73P0574
19R2302
74P1631
74P1633
19R0423
19R0292
19R0294
**
**
**
* *
* *
**
**
**
**
**
**
**
**
**
**
**
2.6GHz Celeron, (models D1S D1Y)
2.8GHz Celeron, (models E1S E1Y)
Intel Celeron 2.4 GHz (models A2S A2Y)
Intel Celeron 2.53 GHz (models B1S B1P B1Y)
2.66GHz Celeron, (models D2S D2Y)
2.8GHz Celeron, (models E2S E2P E2Y E3S E3Y)
2.93GHz Celeron, (models E4S E4Y)
3.06GHz Celeron, (models E5S E5Y)
Intel P4 2.6 GHz (models 41U 41S 41P 41Y 42S 42P 42Y CAU)
Intel P4 2.8 GHz (models s 14U 14S 14P 14Y CBU)
Intel P4 2.8 GHz (models s 12S 12Y)
Intel P4 3.06 GHz (models 22S 22Y)
Intel Prescott P4 2.8 GHz (models 11U 11S 11P 11Y 13S 13P 13Y CCU)
Intel Prescott P4 2.8 GHz (models 15S 15P 15Y CDU)
Intel Prescott P4 3.0 GHz (models 21U 23S 23P 23Y CEU 24U 25S
25Y)
12
12
13
Intel Prescott P4 3.2 GHz (models 31U 32S 32P 32Y CFU 33U 34S 34Y)
Intel Prescott P4 3.4 GHz (models CGU)
19R0296
29R6991
32P4004
**
**
**
Heat sink and fan, Northwood <3.0GHz (models A1S A1Y D1S D1Y
E1S E1Y 41U 41S 41P 41Y 42S 42P 42Y CAU 14U 14S 14P 14Y CBU
12S 12Y)
13
13
Heat sink and fan, Northwood >=3.0 GHZ and all Prescott (models
11U 21U 31U 11S 11P 11Y 13S 13P 13Y CCU 15S 15P 15Y CDU 23S
23P 23Y CEU 32S 32P 32Y CFU A2S A2Y B1S B1P B1Y 33U CGU 24U
22S 22Y E3S E3Y E4S E4Y E5S E5Y 25S 25Y 34S 34Y)
13R9195
13N2951
**
**
Heat sink and fan, Northwood >=3.0 GHZ and all Prescott, Dual Heat
Pipe -- optional to 13R9195 (models 11U 21U 31U 11S 11P 11Y 13S 13P
13Y CCU 15S 15P 15Y CDU 23S 23P 23Y CEU 32S 32P 32Y CFU A2S
A2Y B1S B1P B1Y 33U CGU 24U 22S 22Y E3S E3Y E4S E4Y E5S E5Y
25S 25Y 34S 34Y)
174 Hardware Maintenance Manual
Chapter 11. FRU lists 175
The FRUs listed in the following table are not illustrated.
8149 FRUs
FRU#
CRU
Retention kit (all models)
89P6740
89P6700
*
*
Fan Bracket Assembly >= 3.0Ghz (models 21U 31U 23S 23P 23Y CEU 22S 22Y 32S 32P 32Y
CFU 33U CGU 24U 25S 25Y 34S 34Y)
System board EMC shield kit (all models)
Hard disk drive mounting bracket assembly (all models)
Heat Sink, Grease, Heat Pipe (all models)
Heat Sink, Dual Heat Pipe (all models)
Bezel kit (all models)
89P4761
88P5916
13R9195
13N2951
49P4371
49P4365
89P6749
88P5967
88P5971
88P6515
49P4530
37L5092
19K5548
88P5965
26K1216
33F8354
89P5089
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Cable, dual USB 2.0 (all models)
Cable, dual USB Cable, Long USB 2.0 (all models)
Cable, ATA66 1 drop (all models)
Cable, ATA66 2 drop (all models)
Cable, Diskette drive (all models)
Cable, second serial port (all models)
Cable assembly, power/LED (all models)
5.25 EMC shield (all models)
Misc. hardware kit (all models)
Planar shield (all models)
Battery, 3.0 V (all models)
Mouse, optical wheel (models 11U 21U 31U A1S A1Y D1S D1Y D2S D2Y E1S E1Y E2S E2P
E2Y 41U 41S 41P 41Y 42S 42P 42Y 11S 11P 11Y 12S 12Y 13S 13P 13Y 14U 14S 14P 14Y 15S
15P 15Y 22S 22Y 23S 23P 23Y 32S 32P 32Y A2S A2Y B1S B1P B1Y 33U 24U E3S E3Y E4S
E4Y E5S E5Y 25S 25Y 34S 34Y)
RJ11 connector adapter (Spain, Ireland) (All “G” models)
RJ11 connector adapter (Austria) (All “G” models)
RJ11 connector adapter (Belgium) (All “G” models)
RJ11 connector adapter (Denmark) (All “G” models)
RJ11 connector adapter (Norway, Finland) (All “G” models)
RJ11 connector adapter (France) (All “G” models)
RJ11 connector adapter (Germany) (All “G” models)
RJ11 connector adapter (UK, NZ, HK) (All “G”, “M”, “B”, “H” models)
RJ11 connector adapter (Italy) (All “G” models)
60H6043
60H6045
60H6046
60H6047
60H6048
60H6049
60H6050
60H6051
60H6052
60H6053
60H6054
60H6055
*
*
*
*
*
*
*
*
*
*
*
*
RJ11 connector adapter (Netherlands) (All “G” models)
RJ11 connector adapter (Sweden) (All “G” models)
RJ11 connector adapter (Switzerland) (All “G” models)
8149 Windows XP Pro Recovery CDs
FRU#
39J6414
39J6417
CRU
US (Models 11U 21U 31U 41U 14U 33U 24U)
*
*
SP (models A1S A1Y D1S D1Y D2S D2Y E1S E1Y E2S E2Y 41S 41Y 42S 42Y 11S 11Y 12S
12Y 13S 13Y 14S 14Y 15S 15Y 22S 22Y 23S 23Y 32S 32Y A2S A2Y B1S B1Y E3S E3Y E4S
E4Y E5S E5Y 25S 25Y 34S 34Y)
176 Hardware Maintenance Manual
8149 Windows XP Pro Recovery CDs
FRU#
CRU
BR (models E2P 41P 42P 11P 13P 14P 15P 23P 32P B1P)
39J6419
*
8149 Keyboards (Standard PS/2 Black)
US English (models 11U 21U 31U 41U 14U 33U 24U)
BR (models E2P 41P 42P 11P 13P 14P 15P 23P 32P B1P)
FRU#
CRU
89P8300
89P8304
89P8322
*
*
*
SP/LA (models A1S A1Y D1S D1Y D2S D2Y E1S E1Y E2S E2Y 41S 41Y 42S 42Y 11S 11Y
12S 12Y 13S 13Y 14S 14Y 15S 15Y 22S 22Y 23S 23Y 32S 32Y A2S A2Y B1S B1Y E3S E3Y E4S
E4Y E5S E5Y 25S 25Y 34S 34Y)
8149 Power Cords
FRU#
CRU
Power Cord (models 11U 21U 31U A1S D1S D2S E1S E2S E2P 41U 41S 41P 42S 42P 11S
11P 12S 13S 13P 14U 14S 14P 15S 15P 22S 23S 23P 32S 32P CAU CBU CCU CDU CEU
CFU CTO-U A2S B1S B1P 33U CGU 24U E3S E4S E5S 25S 34S)
6952301
*
Power Cord (EMEA, LA) (models A1S A1Y D1S D1Y D2S D2Y E1S E1Y E2S E2P E2Y 41S
41P 41Y 42S 42P 42Y 11S 11P 11Y 12S 12Y 13S 13P 13Y 14S 14P 14Y 15S 15P 15Y 22S 22Y
23S 23P 23Y 32S 32P 32Y A2S A2Y B1S B1P B1Y E3S E3Y E4S E4Y E5S E5Y 25S 25Y 34S
34Y)
14F0068
36L8879
*
*
Power Cord (APU) (models A1Y D1Y D2Y E1Y E2Y 41Y 42Y 11Y 12Y 13Y 14Y 15Y 22Y
23Y 32Y A2Y B1Y E3Y E4Y E5Y 25Y 34Y)
Chapter 11. FRU lists 177
Machine Type 8174
2
1
3
4
11
7
6
5
10
9
8
Item #
8174 FRUs
FRU#
CRU
1
2
3
Chassis assembly (all models)
74P2256
74P2257
40Y8801
**
*
Bezel and shield kit (all models)
CD-ROM Drive 48X - Black w/o jack & vol (models 22A 22T 22B 22H
22V 22Q 23K)
**
3
3
3
3
CD-ROM Drive 48X - Black w/o jack & vol (models 22A 22T 22B 22H
22V 22QK 23K)
40Y8805
40Y8807
40Y8813
40Y8929
**
**
**
**
CD-ROM Drive 48X - Black w/o jack & vol (models 22A 22T 22B 22H
22V 22Q 23K)
CD-ROM Drive 48X - Black w/o jack & vol (models 22A 22T 22B 22H
22V 22Q 23K)
CD-ROM Drive 48X - Black w/o jack & vol (models 22A 22T 22B 22H
22V 22Q 23K)
4
4
4
5
Diskette drive, 3.5 1.44 MB (all models)
40Y9107
40Y8899
40Y9105
40Y8757
**
**
**
*
Diskette drive, 3.5 1.44 MB (optional to 76H4091 (all models)
Diskette drive, 3.5 1.44 MB (optional to 76H4091 (all models)
Hard disk drive, 40 GB EIDE (models 22A 22T 22B 22H 22V 22Q 23K)
178 Hardware Maintenance Manual
Item #
8174 FRUs
Speaker Asm. Soldered Terminals
FRU#
CRU
6
7
8
8
00N5151
73P2683
19R0703
39J7965
*
*
256 MB SDRAM (models 22A 22T 22B 22H 22V 22Q)
System board, 10/100 E-net, (models 23K)
**
**
System board, (10/100 Enet) w/ video buffer -- optional to 19R0703
(models 23K)
8
8
8
8
System board, (10/100 Enet) w/ video buffer -- optional to 19R0703
(models 23K)
41D0948
19R0837
39J7966
41D0949
**
**
**
**
System board, 10/100 E-net, no AGP (models 22A 22T 22B 22H 22V
22Q)
System board, (10/100 Enet) w/ video buffer, no AGP -- optional to
19R0837 (models 22A 22T 22B 22H 22V 22Q)
System board, (10/100 Enet) w/ video buffer, no AGP -- optional to
19R0837 (models 22A 22T 22B 22H 22V 22Q)
9
Intel Prescott P4 3.0 GHz (models 22A 22T 22B 22H 22V 22Q 23K)
19R0294
13R9195
**
*
10
Heat sink and fan (for Prescott only) (models 22A 22T 22B 22H 22V
22Q 23K)
10
Heat sink and fan, Dual Heat Pipe -- optional to 13R9195 (for Prescott
only) (models 22A 22T 22B 22H 22V 22Q 23K)
13N2951
*
11
11
Power Supply, 230W, PFC (Acbel) (models 22A 22T 23K)
Power Supply, 230W, China (models 22B 22H 22V 22Q)
74P4300
74P4301
N
N
Chapter 11. FRU lists 179
The FRUs listed in the following table are not illustrated.
8174 FRUs
FRU#
CRU
Cable, Diskette drive (all models)
59P8568
75H9219
37L4525
37L5098
26K1216
22P2400
49P1933
09N6708
49P3386
09N6709
49P3387
49P4530
74P2254
88P5927
88P8585
33F8354
89P5089
60H6043
60H6045
60H6046
60H6047
60H6048
60H6049
60H6050
60H6051
60H6052
60H6053
60H6054
60H6055
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Cable, audio (all models)
Cable, IDE (ATA66 1 drop) (all models)
Cable, IDE (ATA66 2 drop) (all models)
Planar shield (all models)
Dual USB 1.1 cable (top channel) (all models)
Audio cable assembly (ATA) (all models)
Front panel label kit (all models)
Access panel (all models)
Cable, power/LED (all models)
Screw kit (all models)
Cable, serial port (all models)
Bracket, second hardfile mount & 6-32 screw (all models)
Cable, serial ATA (all models)
System fan (includes bracket) (models 22A 22T 22B 22H 22V 22Q 23K)
Battery, 3.0 V (all models)
Mouse, optical wheel (models 22A 22T 22B 22H 22V 22Q 23K)
RJ11 connector adapter (Spain, Ireland) (All ″G″ models)
RJ11 connector adapter (Austria) (All ″G″ models)
RJ11 connector adapter (Belgium) (All ″G″ models)
RJ11 connector adapter (Denmark) (All ″G″ models)
RJ11 connector adapter (Norway, Finland) (All ″G″ models)
RJ11 connector adapter (France) (All ″G″ models)
RJ11 connector adapter (Germany) (All ″G″ models)
RJ11 connector adapter (UK, NZ, HK) (All ″G″, ″M″, ″B″, ″H″ models)
RJ11 connector adapter (Italy) (All ″G″ models)
RJ11 connector adapter (Netherlands) (All ″G″ models)
RJ11 connector adapter (Sweden) (All ″G″ models)
RJ11 connector adapter (Switzerland) (All ″G″ models)
8174 Windows XP Pro Recovery CDs
US (models 22A 22T 22H 22Q)
TW (models 22V)
FRU#
CRU
39J6414
30R4820
30R4827
30R4806
*
*
*
*
HK (models 22B)
Korea (models 23K)
8174 Keyboards (Standard PS/2 Black)
US English (models 22A 22H 22Q)
FRU#
CRU
89P8300
89P8306
*
*
Chinese/US (models 22B 22V)
180 Hardware Maintenance Manual
8174 Keyboards (Standard PS/2 Black)
FRU#
89P821
89P8334
CRU
Korean (models 23K)
Thailand (models 22T)
*
*
8174 Power Cords
FRU#
CRU
Power Cord (models 22A 22T 22V)
6952301
13F9978
14F0032
02K0545
02K0545
*
*
*
*
*
Power Cord (EMEA, ANZ, ASEAN Eng, Korea) (models 23K)
Power Cord (EMEA, ANZ, ASEAN Eng, HK Eng) (models 22H)
Power Cord (China, HK) (models 22B 22H)
Power Cord (India) (models 22Q)
Machine Type 8175
2
1
3
4
11
7
6
5
10
9
8
Item #
8175 FRUs
FRU#
CRU
1
2
Chassis assembly (all models)
Bezel and shield kit (all models)
74P2256
74P2257
**
*
Chapter 11. FRU lists 181
Item #
8175 FRUs
FRU#
CRU
3
CD-ROM Drive 48X - Black w/o jack & vol (models 13B 13H 14B 14H
15K 19C 1AC 1BA 1BT 22C 23C 24A 24T 24B 24H 27K 31B 31H 16V
A3J D1V D4Q 41A 41T 43A 43Q 43T 44V 12J 13A 13Q 13T 14Q 14T
16A 16T 1BQ 1BB 1BH 1EA 1ET 1EB 1EH 1HC 1KC 31A 31T D2A
D2T D2B D2H 14A D5A D5T 45A 45T 47A 47Q 47T 1LA 1LQ 1LT
1MA 1MQ 1MT 1PA 1PQ 1PT 1QA 1QT A6Q A7Q A8V B1A B2A B2T
B3A B3Q B3T B3B B3H D6A D7A D7T D8A D8Q D8T D9V E2V DBB
DBH E4A E4Q E4T 51A 51Q 51T 51C 52C 53B 53H DCK E6K)
40Y8801
**
3
3
3
3
CD-ROM Drive 48X - Black w/o jack & vol (models 13B 13H 14B 14H
15K 19C 1AC 1BA 1BT 22C 23C 24A 24T 24B 24H 27K 31B 31H 16V
A3J D1V D4Q 41A 41T 43A 43Q 43T 44V 12J 13A 13Q 13T 14Q 14T
16A 16T 1BQ 1BB 1BH 1EA 1ET 1EB 1EH 1HC 1KC 31A 31T D2A
D2T D2B D2H 14A D5A D5T 45A 45T 47A 47Q 47T 1LA 1LQ 1LT
1MA 1MQ 1MT 1PA 1PQ 1PT 1QA 1QT A6Q A7Q A8V B1A B2A B2T
B3A B3Q B3T B3B B3H D6A D7A D7T D8A D8Q D8T D9V E2V DBB
DBH E4A E4Q E4T 51A 51Q 51T 51C 52C 53B 53H DCK E6K)
40Y8805
40Y8807
40Y8813
40Y8929
**
**
**
**
CD-ROM Drive 48X - Black w/o jack & vol (models 13B 13H 14B 14H
15K 19C 1AC 1BA 1BT 22C 23C 24A 24T 24B 24H 27K 31B 31H 16V
A3J D1V D4Q 41A 41T 43A 43Q 43T 44V 12J 13A 13Q 13T 14Q 14T
16A 16T 1BQ 1BB 1BH 1EA 1ET 1EB 1EH 1HC 1KC 31A 31T D2A
D2T D2B D2H 14A D5A D5T 45A 45T 47A 47Q 47T 1LA 1LQ 1LT
1MA 1MQ 1MT 1PA 1PQ 1PT 1QA 1QT A6Q A7Q A8V B1A B2A B2T
B3A B3Q B3T B3B B3H D6A D7A D7T D8A D8Q D8T D9V E2V DBB
DBH E4A E4Q E4T 51A 51Q 51T 51C 52C 53B 53H DCK E6K)
CD-ROM Drive 48X - Black w/o jack & vol (models 13B 13H 14B 14H
15K 19C 1AC 1BA 1BT 22C 23C 24A 24T 24B 24H 27K 31B 31H 16V
A3J D1V D4Q 41A 41T 43A 43Q 43T 44V 12J 13A 13Q 13T 14Q 14T
16A 16T 1BQ 1BB 1BH 1EA 1ET 1EB 1EH 1HC 1KC 31A 31T D2A
D2T D2B D2H 14A D5A D5T 45A 45T 47A 47Q 47T 1LA 1LQ 1LT
1MA 1MQ 1MT 1PA 1PQ 1PT 1QA 1QT A6Q A7Q A8V B1A B2A B2T
B3A B3Q B3T B3B B3H D6A D7A D7T D8A D8Q D8T D9V E2V DBB
DBH E4A E4Q E4T 51A 51Q 51T 51C 52C 53B 53H DCK E6K)
CD-ROM Drive 48X - Black w/o jack & vol (models 13B 13H 14B 14H
15K 19C 1AC 1BA 1BT 22C 23C 24A 24T 24B 24H 27K 31B 31H 16V
A3J D1V D4Q 41A 41T 43A 43Q 43T 44V 12J 13A 13Q 13T 14Q 14T
16A 16T 1BQ 1BB 1BH 1EA 1ET 1EB 1EH 1HC 1KC 31A 31T D2A
D2T D2B D2H 14A D5A D5T 45A 45T 47A 47Q 47T 1LA 1LQ 1LT
1MA 1MQ 1MT 1PA 1PQ 1PT 1QA 1QT A6Q A7Q A8V B1A B2A B2T
B3A B3Q B3T B3B B3H D6A D7A D7T D8A D8Q D8T D9V E2V DBB
DBH E4A E4Q E4T 51A 51Q 51T 51C 52C 53B 53H DCK E6K)
3
3
DVD-ROM 16X/48X (Black) (models 25V 1DV)
40Y8811
40Y8901
**
**
CD-RW Drive (48X/32X/48X) (models 1CM 25V 29M D3M E1M
DAM E3M)
3
3
DVD-ROM/CD-RW Combo Drive (48x\32x\48x\16x) (models 17K
32K 1TK 2AK)
40Y8781
40Y8903
**
**
DVD-ROM/CD-RW Combo Drive (48x\32x\48x\16x) (models 17K
32K 1TK 2AK)
4
4
4
Diskette drive, 3.5 1.44 MB (all models)
Diskette drive, 3.5 1.44 MB (all models)
Diskette drive, 3.5 1.44 MB (all models)
40Y9107
40Y8899
40Y9105
*
*
*
182 Hardware Maintenance Manual
Item #
8175 FRUs
FRU#
CRU
5
Hard disk drive, 40 GB EIDE (models 13B 13H 14B 14H 15K 16V 17K
18A 19C 1AC 1BA 1BT 21A 22C 23C 24A 24T 24B 24H 27K 31B 31H
A3J D1V D4Q 41A 41T 42Q 43A 43Q 43T 44V 12J 13A 13Q 13T 14Q
14T 16A 16T 1BQ 1BB 1BH 1EA 1ET 1EB 1EH 1FQ 1GQ 1HC 1KC
31A 31T D2A D2T D2B D2H 14A D5A D5T 45A 45T 46Q 47A 47Q 47T
1LA 1LQ 1LT 1MA 1MQ 1MT 1NA 1PA 1PQ 1PT 1QA 1QT 1RQ 1SQ
A5Q A6Q A7Q A8V B1A B2A B2T B3A B3Q B3T B3B B3H D6A D7A
D7T D8A D8Q D8T D9V E2V DBB DBH E4A E4Q E4T 51A 51Q 51T
51C 52C 53B 53H DCK E6K 1TK 2AK)
40Y8757
*
5
Hard disk drive 80 GB EIDE (models 1CM 25V 29M 1DV D3M E1M
DAM E3M)
40Y8758
**
5
5
6
7
Hard disk drive 80 GB Serial ATA (models 32K)
Hard disk drive 80 GB Serial ATA (models 32K)
Speaker Asm. Soldered Terminals
71P7293
40Y8761
00N5151
31P9120
**
**
*
128 MB SDRAM (models A3J D2A D2T D2B D2H 41A 41T 1EA 1ET
1EB 1EH D5A D5T 45A 45T 1QA 1QT A5Q A6Q B1A B2A B2T D6A
D7A D7T DBB DBH)
*
7
256 MB SDRAM (models 13B 13H 14B 14H 15K 16V 17K D1V D3M
D4Q 42Q 43A 43Q 43T 44V 12J 13A 13Q 13T 14Q 14T 16A 16T 1FQ
1GQ 1HC 1KC E1M 14A 46Q 47A 47Q 47T 1LA 1LQ 1LT 1MA 1MQ
1MT 1RQ 1SQ A7Q A8V B3A B3Q B3T B3B B3H D8A D8Q D8T D9V
DAM E2V E3M E4A E4Q E4T E6K 1TK)
31P9121
*
7
7
512 MB SDRAM (models 1CM)
31P9122
73P2683
*
*
256 MB SDRAM (models 18A 19C 1AC 1BA 1BT 21A 22C 23C 24A
24T 24B 24H 25V 27K 31B 31H 32K 1BQ 1BB 1BH 1DV 31A 31T 1NA
1PA 1PQ 1PT 51A 51Q 51T 51C 52C 53B 53H 2AK)
7
8
512 MB SDRAM (models 29M)
73P2684
19R0703
*
System board, 10/100 E-net (models 15K 17K 1CM 27K 29M 32K 16V
25V D1V 44V 16A 16T 1DV A8V D9V E2V 53B 53H 1TK 2AK)
**
8
8
8
System board, (10/100 Enet) w/ video buffer -- optional to 19R0703
(models 15K 17K 1CM 27K 29M 32K 16V 25V D1V 44V 16A 16T 1DV
A8V D9V E2V 53B 53H 1TK 2AK)
39J7965
41D0948
19R0837
**
**
**
System board, (10/100 Enet) w/ video buffer -- optional to 19R0703
(models 15K 17K 1CM 27K 29M 32K 16V 25V D1V 44V 16A 16T 1DV
A8V D9V E2V 53B 53H 1TK 2AK)
System board, 10/100 E-net, no AGP (models 13B 13H 14B 14H 18A
19C 1AC 1BA 1BT 21A 22C 23C 24A 24T 24B 24H 31B 31H A3J D2A
D2T D2B D2H D4Q 41A 41T 42Q 43A 43Q 43T 12J 13A 13Q 13T 14Q
14T 1BQ 1BB 1BH 1EA 1ET 1EB 1EH 1FQ 1GQ 1HC 1KC 31A 31T
14A D3M E1M D5A D5T 45A 45T 46Q 47A 47Q 47T 1LA 1LQ 1LT
1MA 1MQ 1MT 1NA 1PA 1PQ 1PT 1QA 1QT 1RQ 1SQ A5Q A6Q
A7Q B1A B2A B2T B3A B3Q B3T B3B B3H D6A D7A D7T D8A D8Q
D8T DAM E3M DBB DBH E4A E4Q E4T 51A 51Q 51T 51C 52C DCK
E6K)
Chapter 11. FRU lists 183
Item #
8175 FRUs
FRU#
CRU
8
System board, (10/100 Enet) w/ video buffer, no AGP -- optional to
19R0837 (models 13B 13H 14B 14H 18A 19C 1AC 1BA 1BT 21A 22C
23C 24A 24T 24B 24H 31B 31H A3J D2A D2T D2B D2H D4Q 41A 41T
42Q 43A 43Q 43T 12J 13A 13Q 13T 14Q 14T 1BQ 1BB 1BH 1EA 1ET
1EB 1EH 1FQ 1GQ 1HC 1KC 31A 31T 14A D3M E1M D5A D5T 45A
45T 46Q 47A 47Q 47T 1LA 1LQ 1LT 1MA 1MQ 1MT 1NA 1PA 1PQ
1PT 1QA 1QT 1RQ 1SQ A5Q A6Q A7Q B1A B2A B2T B3A B3Q B3T
B3B B3H D6A D7A D7T D8A D8Q D8T DAM E3M DBB DBH E4A
E4Q E4T 51A 51Q 51T 51C 52C DCK E6K)
39J7966
**
8
System board, (10/100 Enet) w/ video buffer, no AGP -- optional to
19R0837 (models 13B 13H 14B 14H 18A 19C 1AC 1BA 1BT 21A 22C
23C 24A 24T 24B 24H 31B 31H A3J D2A D2T D2B D2H D4Q 41A 41T
42Q 43A 43Q 43T 12J 13A 13Q 13T 14Q 14T 1BQ 1BB 1BH 1EA 1ET
1EB 1EH 1FQ 1GQ 1HC 1KC 31A 31T 14A D3M E1M D5A D5T 45A
45T 46Q 47A 47Q 47T 1LA 1LQ 1LT 1MA 1MQ 1MT 1NA 1PA 1PQ
1PT 1QA 1QT 1RQ 1SQ A5Q A6Q A7Q B1A B2A B2T B3A B3Q B3T
B3B B3H D6A D7A D7T D8A D8Q D8T DAM E3M DBB DBH E4A
E4Q E4T 51A 51Q 51T 51C 52C DCK E6K)
41D0949
**
9
9
Intel Celeron 2.4 GHz (models A3J)
88P7699
13R8907
**
**
Intel Celeron 2.6 GHz (models D1V D2A D2T D2B D2H D3M D4Q
D5A D5T)
9
9
9
9
Intel Celeron 2.8 GHz (models E1M)
13R8963
19R0780
19R0417
19R0419
**
Intel Celeron 2.4 GHz (models A5Q A6Q A7Q A8V)
Intel Celeron 2.53 GHz (models B1A B2A B2T B3A B3Q B3T B3B B3H)
* *
* *
* *
Intel Celeron 2.66 GHz (models D6A D7A D7T D8A D8Q D8T D9V
DAM DBB DBH DCK)
9
9
9
9
Intel Celeron 2.8 GHz (models E2V E3M E6K)
Intel Celeron 2.93 GHz (models E4A E4Q E4T)
Intel Celeron 3.06 GHz (models)
19R0421
29R6989
29R6990
73P0574
* *
* *
* *
**
Intel P4 2.6 GHz (models 41A 41T 42Q 43A 43Q 43T 44V 45A 45T 46Q
47A 47Q 47T)
9
Intel P4 2.8 GHz (models 13B 13H 13A 13Q 13T 1EA 1ET 1EB 1EH
1FQ 1LA 1LQ 1LT 1QA 1QT 1RQ)
19R2302
**
9
9
Intel P4 2.8 GHz (models 12J)
74P1631
19R0423
**
**
Intel Prescott P4 2.8 GHz (models 14B 14H 15K 16V 17K 14Q 14T 16A
16T 1GQ 1HC 1KC 14A 1MA 1MQ 1MT 1SQ 1TK)
9
9
Intel Prescott P4 2.8 GHz (models 18A 19C 1AC 1BA 1BT 1CM 1BQ
1BB 1BH 1DV 1NA 1PA 1PQ 1PT)
19R0292
19R0294
**
**
Intel Prescott P4 3.0 GHz (models 21A 22C 23C 24A 24T 24B 24H 25V
27K 29M 2AK)
9
9
Intel Prescott P4 3.2 GHz (models 31B 31H 32K 31A 31T)
19R0296
29R6991
32P4004
**
**
**
Intel Prescott P4 3.4 GHz (models 51A 51Q 51T 51C 52C 53B 53H)
10
Heat sink and fan, Northwood <3.0GHz (models E4A E4Q E4T 13B
13H 14B 14H 15K 16V 17K A3J D1V D2A D2T D2B D2H D3M D4Q
41A 41A 41T 42Q 43A 43Q 43T 44V 12J 13A 13Q 13T 1EA 1ET 1EB
1EH 1FQ E1M D5A D5T 45A 45T 46Q 47A 47Q 47T 1LA 1LQ 1LT
1QA 1QT 1RQ)
184 Hardware Maintenance Manual
Item #
8175 FRUs
FRU#
CRU
10
Heat sink and fan, Northwood >=3.0 GHZ and all Prescott (models
18A 19C 1AC 1BA 1BT 1CM 21A 22C 23C 24A 24T 24B 24H 25V 27K
29M 31B 31H 32K 14Q 14T 16A 16T 1GQ 1HC 1KC 1BQ 1BB 1BH
1DV 31A 31T 14A 1MA 1MQ 1MT 1SQ 1NA 1PA 1PQ 1PT A5Q A6Q
A7Q A8V B1A B2A B2T B3A B3Q B3T B3B B3H D6A D7A D7T D8A
D8Q D8T D9V DAM E2V E3M DBB DBH 51A 51Q 51T 51C 52C 53B
53H DCK E6K 1TK 2AK)
13R9195
**
10
11
11
Fansink, Northwood >=3.0 GHZ and all Prescott, Dual Heat Pipe --
optional to 13R9195 (models 18A 19C 1AC 1BA 1BT 1CM 21A 22C
23C 24A 24T 24B 24H 25V 27K 29M 31B 31H 32K 14Q 14T 16A 16T
1GQ 1HC 1KC 1BQ 1BB 1BH 1DV 31A 31T 14A 1MA 1MQ 1MT 1SQ
1NA 1PA 1PQ 1PT A5Q A6Q A7Q A8V B1A B2A B2T B3A B3Q B3T
B3B B3H D6A D7A D7T D8A D8Q D8T D9V DAM E2V E3M DBB
DBH 51A 51Q 51T 51C 52C 53B 53H DCK E6K 1TK 2AK)
13N2951
74P4300
74P4301
**
N
N
230W Power Supply - AcBel PFC (models 15K 17K 18A 1BA 1BT 1CM
21A 24A 24T 27K 29M 32K A3J D2A D2T D3M D4Q 41A 41T 42Q 43A
43Q 43T 12J 13A 13Q 13T 14Q 14T 16A 16T 1BQ 1EA 1ET 1FQ 1GQ
31A 31T E1M 14A D5A D5T 45A 45T 46Q 47A 47Q 47T 1LA 1LQ 1LT
1MA 1MQ 1MT 1NA 1PA 1PQ 1PT 1QA 1QT 1RQ 1SQ A5Q A6Q
A7Q B1A B2A B2T B3A B3Q B3T D6A D7A D7T D8A D8Q D8T DAM
E3M E4A E4Q E4T 51A 51Q 51T DCK E6K 1TK 2AK)
230W Power Supply - AcBel China version (models 13B 13H 14B 14H
16V 19C 1AC 22C 23C 24B 24H 25V 31B 31H D1V D2B D2H 44V 1BB
1BH 1DV 1EB 1EH 1HC 1KC A8V B3B B3H D9V E2V DBB DBH 51C
52C 53B 53H)
Chapter 11. FRU lists 185
The FRUs listed in the following table are not illustrated.
8175 FRUs
FRU#
CRU
Cable, Diskette drive (all models)
59P8568
75H9219
37L4525
37L5098
26K1216
22P2400
49P1933
09N6708
49P3386
09N6709
49P3387
49P4530
74P2254
88P5927
88P8585
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Cable, audio (all models)
Cable, IDE (ATA66 1 drop) (all models)
Cable, IDE (ATA66 2 drop) (all models)
Planar shield (all models)
Dual USB 1.1 cable (top channel) (all models)
Audio cable assembly (ATA) (all models)
Front panel label kit (all models)
Access panel (all models)
Cable, power/LED (all models)
Screw kit (all models)
Cable, serial port (all models)
Bracket, second hardfile mount & 6-32 screw (all models)
Cable, serial ATA (all models)
System fan (includes bracket) (models 21A 22C 23C 24A 24T 24B 24H 25V 27K 29M 31B
31H 32K 31A 31T 51A 51Q 51T 51C 52C 53B 53H 2AK)
Battery, 3.0 V (all models)
33F8354
49P1750
89P5089
*
*
*
2 Audio Front Panel (models1CM 25V 29M)
Mouse, optical wheel (models 13B 13H 14B 14H 15K 16V 17K 18A 19C 1AC 1BA 1BT 1CM
21A 22C 23C 24A 24T 24B 24H 25V 27K 29M 31B 31H 32K A3J D1V D2A D2T D2B D2H
D3M D4Q 41A 41T 42Q 43A 43Q 43T 44V 12J 13A 13Q 13T 14Q 14T 16A 16T 1BQ 1BB
1BH 1DV 1EA 1ET 1EB 1EH 1FQ 1GQ 1HC 1KC 31A 31T E1M 14A D5A D5T 45A 45T 46Q
47A 47Q 47T 1LA 1LQ 1LT 1MA 1MQ 1MT 1NA 1PA 1PQ 1PT 1QA 1QT 1RQ 1SQ A5Q
A6Q A7Q A8V B1A B2A B2T B3A B3Q B3T B3B B3H D6A D7A D7T D8A D8Q D8T D9V
DAM E2V E3M DBB DBH E4A E4Q E4T 51A 51Q 51T 51C 52C 53B 53H)
PCI Modem Card (Soft), ATX (models 1CM 29M D3M E1M DAM E3M 51A 51Q 51T 51C
52C 53B 53H E6K 1TK)
22P7943
*
64MB, Nvidia GeForce MX 440 (VGA) ATX (models 1TK)
Speakers, Infinity Active T1 (Black)(models 1CM 29M 25V D3M E1M DAM E3M E6K 1TK)
Speaker Power brick - Taiwan (models 25V)
73P0715
25P4726
03R0338
25P5705
88P7687
60H6043
60H6045
60H6046
60H6047
60H6048
60H6049
60H6050
60H6051
60H6052
60H6053
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Speaker Power brick - ANZ (models 1CM 29M D3M E1M DAM E3M)
Speaker Power brick -Korean (models E6K 1TK)
RJ11 connector adapter (Spain, Ireland) (All ″G″ models)
RJ11 connector adapter (Austria) (All ″G″ models)
RJ11 connector adapter (Belgium) (All ″G″ models)
RJ11 connector adapter (Denmark) (All ″G″ models)
RJ11 connector adapter (Norway, Finland) (All ″G″ models)
RJ11 connector adapter (France) (All ″G″ models)
RJ11 connector adapter (Germany) (All ″G″ models)
RJ11 connector adapter (UK, NZ, HK) (All ″G″, ″M″, ″B″, ″H″ models)
RJ11 connector adapter (Italy) (All ″G″ models)
RJ11 connector adapter (Netherlands) (All ″G″ models)
186 Hardware Maintenance Manual
8175 FRUs
RJ11 connector adapter (Sweden) (All ″G″ models)
RJ11 connector adapter (Switzerland) (All ″G″ models)
FRU#
CRU
60H6054
60H6055
*
*
8175 Windows XP Home Recovery CDs
FRU#
CRU
US (models 1CM 29M D3M 41A 41T 1EA 1ET 1EH E1M B1A D6A DAM E3M 51A 51Q
51T)
39J6250
*
SC (models 1AC 23C 1KC 51C)
TW (models 25V)
30R4777
30R4784
27K6746
30R4770
*
*
*
*
HK (models 1EB)
KO (models 15K 17K 27K 32K DCK E6K 1TK 2AK)
8175 Windows XP Pro Recovery CDs
FRU#
CRU
US (models 13H 14H 18A 1BA 1BT 21A 24A 24T 24H 31H D2A D2T D2H 43A 43T 13A
13T 14T 16A 16T 1BH 31A 31T 14A D4Q 42Q 43Q 13Q 14Q 1BQ A7Q B2A B2T B3A B3Q
B3T B3H D7A D7T D8A D8Q D8T DBH E4A E4Q E4T 53H)
39J6414
*
JP (models A3J 12J)
30R4834
30R4820
30R4827
*
*
*
TW (models 16V D1V 44V 1DV A8V D9V E2V)
HK (models 13B 14B 24B 31B D2B 1BB B3B DBB 53B)
8175 Keyboards (Productivity USB)
FRU#
CRU
Korean (models E6K 1TK 2AK)
89P8821
*
8175 Keyboards (Standard PS/2 Black)
FRU#
CRU
US English (models 13H 14H 18A 19C 1AC 1BA 1CM 21A 22C 23C 24A 24H 29M 31H
D2A D2H D3M D4Q 41A 42Q 43A 43Q 13A 13Q 14Q 16A 1BQ 1BH 1EA 1EH 1FQ 1GQ
1HC 1KC 31A E1M 14A D5A 45A 46Q 47A 47Q 1LA 1LQ 1MA 1MQ 1NA 1PA 1PQ 1QA
1RQ 1SQ A5Q A6Q A7Q B1A B2A B3A B3Q B3H D6A D7A D8A D8Q DAM E3M DBH
E4A E4Q 51A 51Q 51C 52C 53H)
89P8300
*
Chinese/US (models 13B 14B 16V 24B 25V 31B D1V D2B 44V 1BB 1DV 1EB A8V B3B D9V
E2V DBB 53B)
89P8306
*
Japanese (models A3J 12J)
89P8320
89P8321
89P8334
*
*
*
Korean (models 15K 17K 27K 32K DCK)
Thailand (models 1BT 24T D2T 41T 43T 13T 14T 16T 1ET 31T D5T 45T 47T 1LT 1MT 1PT
1QT B2T B3T D7T D8T E4T 51T)
8175 Power Cords
FRU#
CRU
Power Cord (models 16V 18A 1BA 1BT 21A 24A 24T 25V D1V D2A D2T 41A 41T 43A 43T
44V 13A 13T 14T 16A 16T 1DV 1EA 1ET 31A 31T 14A D5A D5T 45A 45T 47A 47T 1LA 1LT
1MA 1MT 1NA 1PA 1PT 1QA 1QT A8V B1A B2A B2T B3A B3T D6A D7A D7T D8A D8T
D9V E2V E4A E4T 51A 51T)
6952301
*
Power Cord (ANZ) (models 1CM 29M D3M E1M DAM E3M)
13F9939
13F9978
*
*
Power Cord (EMEA, ANZ, ASEAN Eng, Korea) (models 15K 17K 27K 32K DCK E6K 1TK
2AK)
Power Cord (EMEA, ANZ, ASEAN Eng, HK Eng) (models 13H 14H 24H 31H D2H 1BH
1EH B3H DBH 53H)
14F0032
*
Chapter 11. FRU lists 187
8175 Power Cords
FRU#
CRU
Power Cord (China, HK) (models 13B 13H 14B 14H 19C 1AC 22C 23C 24B 24H 31B 31H
D2B D2H 1BB 1BH 1EB 1EH 1HC 1KC B3B B3H DBB DBH 51C 52C 53B 53H)
02K0545
*
Power Cord (India) (models D4Q 42Q 43Q 13Q 14Q 1BQ 1FQ 1GQ 46Q 47Q 1LQ 1MQ
1PQ 1RQ 1SQ A5Q A6Q A7Q B3Q D8Q E4Q 51Q)
49P2078
*
Machine Type 8176
2
1
3
4
11
7
6
5
10
9
8
Item #
8176 FRUs
FRU#
CRU
**
1
2
3
3
3
3
3
3
Chassis assembly (all models)
74P2256
74P2257
40Y8801
40Y8805
40Y8807
40Y8813
40Y8929
40Y8811
Bezel and shield kit (all models)
*
CD-ROM Drive 48X - Black w/o jack & vol (models D3B D3H)
CD-ROM Drive 48X - Black w/o jack & vol (models D3B D3H)
CD-ROM Drive 48X - Black w/o jack & vol (models D3B D3H)
CD-ROM Drive 48X - Black w/o jack & vol (models D3B D3H)
CD-ROM Drive 48X - Black w/o jack & vol (models D3B D3H)
DVD-ROM 16X/48X (Black) (models 12C D1C 22B D2C)
**
**
**
**
**
**
188 Hardware Maintenance Manual
Item #
8176 FRUs
FRU#
CRU
**
3
3
CD-RW Drive (48X/32X/48X) (models 22B)
40Y8901
40Y8781
DVD-ROM/CD-RW Combo Drive (48x\32x\48x\16x) (models 21C
13C 32C 51C 52C)
**
3
4DVD-ROM/CD-RW Combo Drive (48x\32x\48x\16x) (models 21C
13C 32C 51C 52C)
40Y8903
**
4
4
4
5
5
5
5
5
6
7
7
7
8
8
Diskette drive, 3.5 1.44 MB (all models)
40Y9107
40Y8899
40Y9105
40Y8757
40Y8758
40Y8759
71P7293
40Y8761
00N5151
31P9120
31P9121
73P2683
19R0703
39J7965
*
*
Diskette drive, 3.5 1.44 MB (all models)
Diskette drive, 3.5 1.44 MB (all models)
*
Hard disk drive, 40 GB EIDE (models 22B D3B D3H)
Hard disk drive, 80 GB EIDE (models D1C 13C D2C)
Hard disk drive, 120 GB EIDE (models 21C 32C 51C 52C)
Hard disk drive, 80 GB SATA (models 11C 12C 21C)
Hard disk drive, 80 GB SATA (models 11C 12C 21C)
Speaker Asm. Soldered Terminals
*
*
*
**
**
*
128 MB SDRAM (models D1C D3B D3H)
*
256 MB SDRAM (models 12C 13C D2C)
*
256 MB SDRAM (models 21C 22B 32C 51C 52C)
System board, 10/100 E-net (models 12C 21C 13C 32C 51C 52C)
*
**
**
System board, (10/100 Enet) w/ video buffer -- optional to 19R0703
(models 12C 21C 13C 32C 51C 52C)
8
8
8
8
System board, (10/100 Enet) w/ video buffer -- optional to 19R0703
(models 12C 21C 13C 32C 51C 52C)
41D0948
19R0837
39J7966
41D0949
**
**
**
**
System board, 10/100 E-net, no AGP (models D1C 22B D2C D3B
D3H)
System board, (10/100 Enet) w/ video buffer, no AGP -- optional to
19R0837 (models D1C 22B D2C D3B D3H)
System board, (10/100 Enet) w/ video buffer, no AGP -- optional to
19R0837 (models D1C 22B D2C D3B D3H)
9
9
Intel P4 2.66 GHz (models D2C D3B D3H)
Intel P4 2.6 GHz (models D1C)
19R0419
73P0574
19R2302
19R0423
19R0294
19R0296
29R6991
32P4004
13R9195
**
**
**
**
**
**
**
**
**
9
Intel P4 2.8 GHz (models 12C)
9
Intel Prescott P4 2.8 GHz (models 13C)
Intel Prescott P4 3.0 GHz (models 21C 22B)
Intel Prescott P4 3.2 GHz (models 32C)
Intel Prescott P4 3.4 GHz (models 51C 52C)
Heat sink and fan, Northwood <3.0GHz (models 12C D1C)
9
9
9
10
10
Heat sink and fan, Northwood >=3.0 GHZ and all Prescott (models
21C 13C 22B 32C D2C D3B D3H 51C 52C)
10
11
Heat sink and fan, Northwood >=3.0 GHZ and all Prescott, Dual Heat
Pipe -- optional to 13R9195 (models 21C 13C 22B 32C D2C D3B D3H
51C 52C)
13N2951
74P4301
**
N
230W Power Supply - AcBel China version (models 12C 21C D1C 13C
22B 32C D2C D3B D3H 51C 52C)
Chapter 11. FRU lists 189
The FRUs listed in the following table are not illustrated.
8176 FRUs
FRU#
CRU
Cable, Diskette drive (all models)
59P8568
75H9219
37L4525
37L5098
22P2400
49P1933
09N6708
49P3386
09N6709
49P3387
49P4530
74P2254
88P5927
26K1216
88P8585
49P1750
33F8354
89P5089
22P7943
73P0715
88P6084
25P4726
25P5703
10K2597
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Cable, audio (all models)
Cable, IDE (ATA66 1 drop) (all models)
Cable, IDE (ATA66 2 drop) (all models)
Dual USB 1.1 cable (top channel) (all models)
Audio cable assembly (ATA) (all models)
Front panel label kit (all models)
Access panel (all models)
Cable, power/LED (all models)
Screw kit (all models)
Cable, serial port (all models)
Bracket, second hardfile mount & 6-32 screw (all models)
Cable, serial ATA (all models)
Planar shield (all models)
System fan (includes bracket) (models 21C 22B 32C 51C 52C)
2 Audio Front Panel (models 12C 21C D1C 13C 22B 32C D2C 51C 52C)
Battery, 3.0 V (all models)
Mouse, optical wheel (models 12C 21C D1C 13C 22B 32C D2C D3B D3H 51C 52C)
PCI Modem Card (Soft), ATX (models 12C 21C D1C 13C 22B 32C D2C 51C 52C)
64MB, Nvidia GeForce MX 440 (VGA) ATX (models 21C 32C 51C)
ATI RADEON 9600 (models 52C)
Speakers, Infinity Active T1 (Black)(models 12C 21C D1C 13C 22B 32C D2C 51C 52C)
Speaker Power brick - UK, Hong Kong (3 prong) (models 22B)
Speaker Power brick - China, Hong Kong (newer 2 prong) (models 12C 21C D1C 13C 22B
32C D2C 51C 52C)
RJ11 connector adapter (Spain, Ireland) (All ″G″ models)
RJ11 connector adapter (Austria) (All ″G″ models)
RJ11 connector adapter (Belgium) (All ″G″ models)
RJ11 connector adapter (Denmark) (All ″G″ models)
RJ11 connector adapter (Norway, Finland) (All ″G″ models)
RJ11 connector adapter (France) (All ″G″ models)
RJ11 connector adapter (Germany) (All ″G″ models)
RJ11 connector adapter (UK, NZ, HK) (All ″G″, ″M″, ″B″, ″H″ models)
RJ11 connector adapter (Italy) (All ″G″ models)
60H6043
60H6045
60H6046
60H6047
60H6048
60H6049
60H6050
60H6051
60H6052
60H6053
60H6054
60H6055
*
*
*
*
*
*
*
*
*
*
*
*
RJ11 connector adapter (Netherlands) (All ″G″ models)
RJ11 connector adapter (Sweden) (All ″G″ models)
RJ11 connector adapter (Switzerland) (All ″G″ models)
8176 Windows XP Home Recovery CDs
FRU#
CRU
SC (models 12C 21C 13C 32C 51C 52C)
30R4777
*
190 Hardware Maintenance Manual
8176 Windows XP Home Recovery CDs
8176 Windows XP Pro Recovery CDs
FRU#
CRU
HK (models 22B)
27K6746
*
FRU#
39J6414
30R4827
CRU
US/UK/AP/TH (models D3H)
HK (models D3B)
*
*
8176 Keyboards (Preferred Pro PS/2 Fullsize)
FRU#
CRU
US English (models D3H)
Chinese/US (models D3B)
89P8300
89P8807
*
*
8176 Keyboards (Productivity USB)
FRU#
CRU
US English (models 12C 21C D1C 13C 32C D2C 51C 52C)
Chinese/US (models 22B)
89P8800
89P8807
*
*
8176 Power Cords
FRU#
CRU
Power Cord (EMEA,ANZ,ASEAN,Eng,HK Eng) (models D3H)
Power Cord (China, HK) (models 12C 21C D1C 13C 22B 32C D2C D3B D3H 51C 52C)
14F0032
02K0545
*
*
Chapter 11. FRU lists 191
Machine Type 8177
1
2
3
13
4
12
11
10
5
9
8
7
6
Item #
8177 FRUs
FRU#
CRU
**
1
2
Top cover assembly (all models)
230W Power Supply - AcBel PFC (models 21M 21A E3U D1U A3G
88P5962
74P4300
N
B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG B1U D3U
E4U E4G 33G 51G 52G 7FG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
2
230W Power Supply - AcBel China version (models 11S 21C 21B 21H
21V 22S A1S D4S 12S D2S A1Y D2P D2Y D4P D4Y E1S E1P E1Y 12Y
21Q 22P 22Y B1S B1P E3S E6S E6Y 26S 26Y 34S 34Y)
74P4301
N
3
4
Pivot lock, 5.25 DASD (all models)
09N5747
40Y8801
**
*
CD-ROM Drive 48X - Black w/o jack & vol (models 21M 21A 21C
21B 21H 21V E3U D1U A3G B1G D3G E2G 11G 13G 16G 17G 21Q
23G 25G 32G 72G 74G 75G 76G 77G 78G 79G 7AG 7DG A2G A3U
21T B1U B1S B1P D3U E3S E4U E4G 33G 51G 7FG 7HG 7JG E7G)
4
4
CD-ROM Drive 48X - Black w/o jack & vol (models 21M 21A 21C
21B 21H 21V E3U D1U A3G B1G D3G E2G 11G 13G 16G 17G 21Q
23G 25G 32G 72G 74G 75G 76G 77G 78G 79G 7AG 7DG A2G A3U
21T B1U B1S B1P D3U E3S E4U E4G 33G 51G 7FG 7HG 7JG E7G)
40Y8805
40Y8807
*
*
CD-ROM Drive 48X - Black w/o jack & vol (models 21M 21A 21C
21B 21H 21V E3U D1U A3G B1G D3G E2G 11G 13G 16G 17G 21Q
23G 25G 32G 72G 74G 75G 76G 77G 78G 79G 7AG 7DG A2G A3U
21T B1U B1S B1P D3U E3S E4U E4G 33G 51G 7FG 7HG 7JG E7G)
192 Hardware Maintenance Manual
Item #
8177 FRUs
FRU#
CRU
4
CD-ROM Drive 48X - Black w/o jack & vol (models 21M 21A 21C
21B 21H 21V E3U D1U A3G B1G D3G E2G 11G 13G 16G 17G 21Q
23G 25G 32G 72G 74G 75G 76G 77G 78G 79G 7AG 7DG A2G A3U
21T B1U B1S B1P D3U E3S E4U E4G 33G 51G 7FG 7HG 7JG E7G)
40Y8813
*
4
CD-ROM Drive 48X - Black w/o jack & vol (models 21M 21A 21C
21B 21H 21V E3U D1U A3G B1G D3G E2G 11G 13G 16G 17G 21Q
23G 25G 32G 72G 74G 75G 76G 77G 78G 79G 7AG 7DG A2G A3U
21T B1U B1S B1P D3U E3S E4U E4G 33G 51G 7FG 7HG 7JG E7G)
40Y8929
*
4
5
DVD-ROM 16X/48X (Black) (models 15G 24G 31G 73G 7BG 7CG 7EG
52G 7KG 7LG 7MG 7NG)
40Y8811
40Y8757
*
*
Hard disk drive, 40 GB EIDE (models 21M 21A 21C 21B 21H 21V A1S
D4S E3U 12S D1U D2S A1Y A3G B1G D2P D2Y D3G D4P D4Y E1S
E1P E1Y E2G 11G 12Y 13G 14G 16G 17G 21Q 23G 25G 32G 72G 74G
75G 76G 77G 78G 79G 7AG 7DG A2G A3U 21T B1U B1S B1P D3U
E3S E4U E4G 33G 51G 7FG 7HG 7JG E6S E6Y E7G 7LG 7MG 7NG)
5
6
Hard disk drive, 80 GB EIDE (models 11S 22S 15G 22P 22Y 24G 31G
73G 7BG 7CG 7EG 52G 7KG 26S 26Y 34S 34Y)
40Y8758
40Y9107
*
Diskette drive, 3.5 1.44 MB (models 11S 21M 21A 21C 21B 21H 21V
22S 13G 15G 16G 21Q 22P 22Y 24G 25G 31G 32G 73G 7AG 7BG 7CG
7EG CTO-U CTO-G 21T A1S D4S E3U 12S D1U D2S A1Y A3G B1G
D2P D2Y D3G D4P D4Y E1S E1P E1Y E2G 11G 12Y 14G 17G 23G 72G
74G 75G 76G 77G 78G 79G 7DG A2G A3U B1U B1S B1P D3U E3S
E4U E4G 33G 51G 52G 7FG 7HG 7JG 7KG E6S E6Y 26S 26Y 34S 34Y
E7G 7LG 7MG 7NG)
**
6
6
Diskette drive, 3.5 1.44 MB (models 11S 21M 21A 21C 21B 21H 21V
22S 13G 15G 16G 21Q 22P 22Y 24G 25G 31G 32G 73G 7AG 7BG 7CG
7EG CTO-U CTO-G 21T A1S D4S E3U 12S D1U D2S A1Y A3G B1G
D2P D2Y D3G D4P D4Y E1S E1P E1Y E2G 11G 12Y 14G 17G 23G 72G
74G 75G 76G 77G 78G 79G 7DG A2G A3U B1U B1S B1P D3U E3S
E4U E4G 33G 51G 52G 7FG 7HG 7JG 7KG E6S E6Y 26S 26Y 34S 34Y
E7G 7LG 7MG 7NG)
40Y8899
40Y9105
**
**
Diskette drive, 3.5 1.44 MB (models 11S 21M 21A 21C 21B 21H 21V
22S 13G 15G 16G 21Q 22P 22Y 24G 25G 31G 32G 73G 7AG 7BG 7CG
7EG CTO-U CTO-G 21T A1S D4S E3U 12S D1U D2S A1Y A3G B1G
D2P D2Y D3G D4P D4Y E1S E1P E1Y E2G 11G 12Y 14G 17G 23G 72G
74G 75G 76G 77G 78G 79G 7DG A2G A3U B1U B1S B1P D3U E3S
E4U E4G 33G 51G 52G 7FG 7HG 7JG 7KG E6S E6Y 26S 26Y 34S 34Y
E7G 7LG 7MG 7NG)
7
8
Speaker assembly (models 21M 21A 21T 21C 21B 21H 21V)
Pivot lock, 3.5 Diskette drive (all models)
00N5151
09N5748
88P5963
31P9120
31P9121
*
**
**
*
9
Chassis/top cover kit (all models)
10
10
128 MB SDRAM (models A1S D4S D2S A1Y D2P D2Y D4P D4Y)
256 MB SDRAM (models 11S E3U 12S D1U A3G B1G D3G E1S E1P
E1Y E2G 11G 12Y 13G 14G 17G 72G 73G 74G 75G 76G 77G 78G 79G
7AG A2G A3U B1U B1S B1P D3U E3S E4U E4G 7FG E7G 7LG 7MG
7NG)
*
10
11
256 MB SDRAM (models 21M 21A 21C 21B 21H 21V 22S 15G 16G
21Q 22P 22Y 23G 24G 25G 31G 32G 7BG 7CG 7DG 7EG 21T 33G 51G
52G 7HG 7JG 7KG E6S E6Y 26S 26Y 34S 34Y)
73P2683
19R0703
*
System board, 10/100 E-net (models 11S 21M 21A 21C 21B 21H 21V
22S 13G 15G 16G 21Q 22P 22Y 24G 25G 31G 32G 73G 7AG 7BG 7CG
7EG CTO-U CTO-G 21T 52G 7KG)
**
Chapter 11. FRU lists 193
Item #
8177 FRUs
FRU#
CRU
11
System board, (10/100 Enet) w/ video buffer -- optional to 19R0703
(models 11S 21M 21A 21C 21B 21H 21V 22S 13G 15G 16G 21Q 22P
22Y 24G 25G 31G 32G 73G 7AG 7BG 7CG 7EG CTO-U CTO-G 21T
52G 7KG)
39J7965
**
11
11
System board, (10/100 Enet) w/ video buffer -- optional to 19R0703
(models 11S 21M 21A 21C 21B 21H 21V 22S 13G 15G 16G 21Q 22P
22Y 24G 25G 31G 32G 73G 7AG 7BG 7CG 7EG CTO-U CTO-G 21T
52G 7KG)
41D0948
19R0837
**
**
System board, 10/100 E-net, no AGP (models A1S D4S E3U 12S D1U
D2S A1Y A3G B1G D2P D2Y D3G D4P D4Y E1S E1P E1Y E2G 11G
12Y 14G 17G 23G 72G 74G 75G 76G 77G 78G 79G 7DG A2G A3U
B1U B1S B1P D3U E3S E4U E4G 33G 51G 7FG 7HG 7JG E6S E6Y 26S
26Y 34S 34Y E7G 7LG 7MG 7NG)
11
11
System board, (10/100 Enet) w/ video buffer, no AGP -- optional to
19R0837 (models A1S D4S E3U 12S D1U D2S A1Y A3G B1G D2P D2Y
D3G D4P D4Y E1S E1P E1Y E2G 11G 12Y 14G 17G 23G 72G 74G 75G
76G 77G 78G 79G 7DG A2G A3U B1U B1S B1P D3U E3S E4U E4G
33G 51G 7FG 7HG 7JG E6S E6Y 26S 26Y 34S 34Y E7G 7LG 7MG
7NG)
39J7966
**
**
System board, (10/100 Enet) w/ video buffer, no AGP -- optional to
19R0837 (models A1S D4S E3U 12S D1U D2S A1Y A3G B1G D2P D2Y
D3G D4P D4Y E1S E1P E1Y E2G 11G 12Y 14G 17G 23G 72G 74G 75G
76G 77G 78G 79G 7DG A2G A3U B1U B1S B1P D3U E3S E4U E4G
33G 51G 7FG 7HG 7JG E6S E6Y 26S 26Y 34S 34Y E7G 7LG 7MG
7NG)
41D0949
12
12
12
Intel Celeron 2.4 GHz (models A1S D4S A1S A1Y A3G 74G A2G A3U)
Intel Celeron 2.6 GHz (models D4S D1U D4P D4Y)
88P7699
13R8907
19R0417
**
**
**
Intel Celeron 2.53 GHz (models B1G 76G CTO-U CTO-G B1U B1S
B1P)
12
12
12
12
12
12
12
12
12
12
Intel Celeron 2.66 GHz (models D2S D2P D2Y D3G 75G D3U)
Intel Celeron 2.8 GHz (models E3U E1S E1P E1Y E2G 78G E3S 7LG)
Intel Celeron 2.93 GHz (models E4U E4G 7FG 7MG)
Intel Celeron 3.06 GHz (models E6S E6Y E7G 7NG)
Intel P4 2.8 GHz (models 72G)
19R0419
19R0421
29R6989
29R6990
19R2302
74P1631
88P5869
19R0423
19R0292
19R0294
**
**
**
**
**
**
**
**
**
**
Intel P4 2.8 GHz (models 11S 11G 12Y 79G)
Intel P4 2.8 GHz (models 12S)
Intel Prescott P4 2.8 GHz (models 13G 14G 17G 73G 77G 7AG)
Intel Prescott P4 2.8 GHz (models 15G 16G 7BG)
Intel Prescott P4 3.0 GHz (models 21M 21A 21C 21B 21H 21V 22S 21Q
22P 22Y 23G 24G 25G 7CG 7DG 21T 26S 26Y)
12
12
13
Intel Prescott P4 3.2 GHz (models 31G 32G 7EG 33G 7HG 34S 34Y)
Intel Prescott P4 3.4 GHz (models51G 52G 7JG 7KG)
19R0296
29R6991
32P4004
**
**
*
Heat sink and fan, Northwood <3.0GHz (modelsE4U E4G 7FG 11S
A1S D4S 12S A1S D4S 12S D1U A1Y A3G 74G D4P D4Y 78G 11G 12Y
79G 72G A2G A3U)
194 Hardware Maintenance Manual
Item #
8177 FRUs
FRU#
CRU
13
Heat sink and fan, Northwood >=3.0 GHZ and all Prescott (models
21M 21A 21C 21B 21H 21V 22S 13G 14G 17G 73G 77G 7AG 15G 16G
7BG 21Q 22P 22Y 23G 24G 25G 7CG 7DG 31G 32G 7EG 21T B1U B1S
B1P D3U E3S B1G 76G D2S D2P D2Y D3G 75G E3U E1S E1P E1Y
E4U E4G 7FG 31G 32G 7EG 33G 7HG 51G 52G 7JG 7KG E5U E5G
7GG E6S E6Y 26S 26Y 34S 34Y E7G 7NG 7LG 7MG)
13R9195
*
13
Heat sink and fan, Northwood >=3.0 GHZ and all Prescott , Dual
Heat Pipe -- optional to 13R9195 (models 21M 21A 21C 21B 21H 21V
22S 13G 14G 17G 73G 77G 7AG 15G 16G 7BG 21Q 22P 22Y 23G 24G
25G 7CG 7DG 31G 32G 7EG 21T B1U B1S B1P D3U E3S B1G 76G D2S
D2P D2Y D3G 75G E3U E1S E1P E1Y E4U E4G 7FG 31G 32G 7EG
33G 7HG 51G 52G 7JG 7KG E5U E5G 7GG E6S E6Y 26S 26Y 34S 34Y
E7G 7NG 7LG 7MG)
13N2951
*
Chapter 11. FRU lists 195
The FRUs listed in the following table are not illustrated.
8177 FRUs
FRU#
CRU
Retention kit (all models)
89P6740
89P6700
*
*
Fan bracket assembly (models 21M 21A 21C 21B 21H 21V 22S 21Q 22P 22Y 23G 24G 25G
7CG 7DG 31G 32G 7EG 21T 33G 7HG 51G 52G 7JG 7KG 26S 26Y 34S 34Y E7G 7NG)
System board EMC shield kit (all models)
Hard disk drive mounting bracket assembly (all models)
Bezel kit (all models)
89P4761
88P5916
49P4371
49P4365
88P5967
88P5971
88P6515
49P4530
00N5151
37L5092
19K5548
88P5965
26K1216
33F8354
24P0383
89P5089
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Cable, dual USB 2.0 (all models)
Cable, ATA66 1 drop (all models)
Cable, ATA66 2 drop (all models)
Cable, Diskette drive (all models)
Cable, second serial port (all models)
Speaker Asm (models 21M 21A 21C 21B 21H 21V 21Q 21T E6S E6Y 26S 26Y 34S 34Y)
Cable assembly, power/LED (all models)
5.25 EMC shield (all models)
Misc. hardware kit (all models)
Planar shield (all models)
Battery, 3.0 V (all models)
Mouse, 2 button, black (models D1U A1U E1U)
Mouse, optical wheel (models 21M 21A 21C 21B 21H 21V 11S 22S A1S D4S 12S D2S A1Y
D2P D2Y D4P D4Y E1S E1P E1Y 12Y 13G 15G 16G 21Q 22P 22Y 24G 25G 31G 32G 73G
7BG 7CG 7EG A3G B1G D1U D3G E2G E3U 11G 14G 17G 23G 72G 74G 75G 76G 77G 78G
79G 7AG 7DG A2G A3U 21T B1U B1S B1P D3U E3S E4U E4G 33G 51G 52G 7FG 7HG 7JG
7KG E6S E6Y 26S 26Y 34S 34Y E7G 7LG 7MG 7NG)
RJ11 connector adapter (Spain, Ireland) (All “G” models)
RJ11 connector adapter (Austria) (All “G” models)
RJ11 connector adapter (Belgium) (All “G” models)
RJ11 connector adapter (Denmark) (All “G” models)
RJ11 connector adapter (Norway, Finland) (All “G” models)
RJ11 connector adapter (France) (All “G” models)
RJ11 connector adapter (Germany) (All “G” models)
RJ11 connector adapter (UK, NZ, HK) (All “G”, “M”, “B”, “H” models)
RJ11 connector adapter (Italy) (All “G” models)
60H6043
60H6045
60H6046
60H6047
60H6048
60H6049
60H6050
60H6051
60H6052
60H6053
60H6054
60H6055
*
*
*
*
*
*
*
*
*
*
*
*
RJ11 connector adapter (Netherlands) (All “G” models)
RJ11 connector adapter (Sweden) (All “G” models)
RJ11 connector adapter (Switzerland) (All “G” models)
8177 Windows XP Home Recovery CDs
FRU#
19R2723
CRU
US (models A2G)
FR (models A2G)
GR (models A2G)
IT (models A2G)
*
*
*
*
39J6251
39J6252
39J6254
196 Hardware Maintenance Manual
8177 Windows XP Home Recovery CDs
FRU#
CRU
DK (models A2G)
NL (models A2G)
AE (models A2G)
SV (models A2G)
HE (models A2G)
FI (models A2G)
NO (models A2G)
PL (models A2G)
PO (models A2G)
RU (models A2G)
HU (models A2G)
CZ (models A2G)
TR (models A2G)
GK (models A2G)
39J6257
39J6260
39J6264
39J6256
39J6261
39J6258
39J6259
39J6262
39J6268
39J6265
39J6267
39J6263
39J6266
39J6269
*
*
*
*
*
*
*
*
*
*
*
*
*
*
8177 Windows XP Pro Recovery CDs
FRU#
CRU
US (Models 21M 21A 21H D1U E3U A2U A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G
23G 24G 25G 31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A3U
21T 21Q B1U D3U E4U E4G 33G 51G 52G 7FG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
39J6414
39J6415
39J6416
39J6418
39J6417
*
*
*
*
*
FR (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
GR (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
IT (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G 73G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG 7GG 7HG 7JG
7KG E7G 7LG 7MG 7NG)
SP (models 22S D2S A1S D4S 12S A1Y A3G B1G D2Y D3G D4Y E1S E1Y E2G 11G 12Y 13G
14G 15G 16G 17G 22Y 23G 24G 25G 31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG
7BG 7CG 7DG 7EG B1S E3S E4G 33G 51G 52G 7FG 7HG 7JG 7KG E6S E6Y 26S 26Y 34S
34Y)
BR (models D2P D4P E1P 22P B1P)
39J6419
39J6421
*
*
DK (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
NL (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
39J6424
39J6428
39J6420
*
*
*
AE (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
SV (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
Chapter 11. FRU lists 197
8177 Windows XP Pro Recovery CDs
FRU#
CRU
HE (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
39J6425
*
FI (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G 73G
74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG 7GG 7HG 7JG
7KG E7G 7LG 7MG 7NG)
39J6422
39J6423
39J6426
39J6432
41D1950
41D1949
39J6431
39J6427
39J6430
39J6433
39J6434
*
*
*
*
*
*
*
*
*
*
*
NO (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
PL (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
PO (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
RU (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
RE (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
HU (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
CZ (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
TR (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
GK (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
SL (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
CS (models 21C)
Taiwan (models 21V)
HK (models 21B)
30R4834
30R4813
30R4827
39J7221
*
*
*
*
Multilingual 1 (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
Multilingual 2 (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG E4G 33G 51G 52G 7FG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
39J7222
*
198 Hardware Maintenance Manual
8177 Keyboard (Preferred Pro Fullsize, PS/2, Stealth Black)
FRU#
CRU
US English (models 21M 21A 21C 21H E3U D1U A3G B1G D3G E2G 11G 13G 14G 15G
16G 17G 21Q 23G 24G 25G 31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG
7DG 7EG A2G A3U B1U D3U E4U E4G 33G 51G 52G 7FG 7HG 7JG 7KG E7G 7LG 7MG
7NG)
89P8300
*
Arabic (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
89P8301
89P8302
89P8305
89P8307
89P8308
89P8309
89P8310
89P8313
89P8314
89P8303
89P8315
89P8316
89P8317
89P8318
89P8319
89P8322
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Belgian/French (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G
7FG 7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Bulgarian (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG
7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Czech (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
Danish (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG
7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Dutch (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
French (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
German (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG
7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Greek (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
Belgian/UK (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G
7FG 7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Hebrew (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG
7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Hungarian (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG
7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Iceland (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG
7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Italian 141 (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG
7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Italian 142 (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG
7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
LA Spanish (models 11S 22S A1S D4S 12S D2S A1Y D2Y D4Y E1S E1Y 12Y 22Y B1S E3S
E6S E6Y 26S 26Y 34S 34Y)
Chapter 11. FRU lists 199
8177 Keyboard (Preferred Pro Fullsize, PS/2, Stealth Black)
FRU#
CRU
Norwegian (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG
7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
89P8323
*
Polish (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
89P8324
89P8325
89P8326
*
*
*
Portuguese (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG
7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Romanian (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG
7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Russian (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G
89P8327
89P8328
*
*
Russian/Cyrillic (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G
31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G
52G 7FG 7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Serbian/Cyrillic (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G
7FG 7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
89P8329
89P8330
89P8331
89P8332
89P8333
*
*
*
*
*
Slovak (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G
73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG 7GG
7HG 7JG 7KG E7G 7LG 7MG 7NG)
Spanish (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG
7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Swedish/Finn (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G
7FG 7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Swiss F/G (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG
7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Thailand (models 21T)
89P8334
89P8335
*
*
Turkish 440 (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G
7FG 7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Turkish 179 (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G
7FG 7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
89P8336
89P8337
89P8338
89P8339
89P8304
*
*
*
*
*
UK English (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G
7FG 7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
US Euro (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G 32G
72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG
7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Yugoslav/Latin (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G 25G 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G
7FG 7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Brazil/Portuguese (models D2P D4P E1P 22P B1P)
200 Hardware Maintenance Manual
8177 Keyboards (Productivity USB)
US English (models E4U E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Arabic (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Arabic/French (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Belgian/French (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Belgian/UK (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Bulgarian (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Czech (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Danish (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Dutch (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
French (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
German (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Greek (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Hebrew (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Hungarian (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Iceland (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Italian 141 (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Norwegian (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Polish (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Portuguese (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Romanian (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Romanian (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Russian/Cyrillic (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Serbian/Cyrillic (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Slovak (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Spanish (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Swedish/Finn (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Swiss F/G (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Turkish 440 (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Turkish 179 (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
UK English (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
US International (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
Yugoslav/Latin (models E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG)
FRU#
CRU
89P8800
89P8801
89P8802
89P8803
89P8804
89P8806
89P8808
89P8809
89P8810
89P8811
89P8814
89P8815
89P8816
89P8817
89P8818
89P8819
89P8823
89P8824
89P8825
89P8826
89P8827
89P8828
89P8829
89P8830
89P8831
89P8832
89P8833
89P8835
89P8836
89P8837
89P8838
89P8839
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
8177 Power Cords
FRU#
CRU
Power Cord (models 11S 21A 21V 22S A1S D4S E3U 12S D1U A3G B1G D2P D3G D4P E1S
E1P E2G 11G 13G 14G 15G 16G 17G 22P 23G 24G 25G 31G 32G 72G 73G 74G 75G 76G
77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G A3U 21T B1U B1S B1P D3U E3S E4U E4G 33G
51G 52G 7FG 7HG 7JG 7KG E6S 26S 34S E7G 7LG 7MG 7NG)
6952301
*
Power Cord (ANZ) (models 21M)
13F9939
13F9978
*
*
Power Cord (EMEA, ANZ, ASEAN Eng, Korea) (models A3G B1G D3G E2G 11G 13G 14G
15G 16G 17G 23G 24G 25G 31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG
7DG 7EG A2G E4G 33G 51G 52G 7FG 7GG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Chapter 11. FRU lists 201
8177 Power Cords
FRU#
CRU
Power Cord (EMEA, ANZ, ASEAN Eng, HK Eng) (models 21H A3G B1G D3G E2G 11G
13G 14G 15G 16G 17G 23G 24G 25G 31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG
7BG 7CG 7DG 7EG A2G E4G 33G 51G 52G 7FG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
14F0032
*
Power Cord (EMEA) (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G
25G 31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G
51G 52G 7FG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
13F9996
14F0068
*
*
Power Cord (EMEA, LA) (models 11S 22S A1S D4S 12S D2S A1Y A3G B1G D2P D2Y D3G
D4P D4Y E1S E1P E1Y E2G 11G 12Y 13G 14G 15G 16G 17G 22P 22Y 23G 24G 25G 31G
32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G B1S B1P E3S E4G
33G 51G 52G 7FG 7HG 7JG 7KG E6S E6Y 26S 26Y 34S 34Y)
Power Cord (APU) (models A1Y D2Y D4Y E1Y 12Y 22Y E6Y 26Y 34Y)
Power Cord (China, HK) (models 21C 21B 21H)
36L8879
02K0545
14F0086
*
*
*
Power Cord (EMEA) (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G
25G 31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G
51G 52G 7FG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Power Cord (EMEA, ANZ, ASEAN Eng) (models A3G B1G D3G E2G 11G 13G 14G 15G
16G 17G 23G 24G 25G 31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG
7EG A2G E4G 33G 51G 52G 7FG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
14F0014
14F0050
49P2078
*
*
*
Power Cord (EMEA) (models A3G B1G D3G E2G 11G 13G 14G 15G 16G 17G 23G 24G
25G 31G 32G 72G 73G 74G 75G 76G 77G 78G 79G 7AG 7BG 7CG 7DG 7EG A2G E4G 33G
51G 52G 7FG 7HG 7JG 7KG E7G 7LG 7MG 7NG)
Power Cord (India) (models 21Q)
202 Hardware Maintenance Manual
Machine Type 8178
1
2
3
13
4
12
11
10
5
9
8
7
6
Item #
8178 FRUs
FRU#
CRU
**
1
2
Top cover assembly (all models)
88P5962
74P4300
230W Power Supply - AcBel PFC (models D1M 12M 12A 13M 21M
22M 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G
CT0-U CTO-G D2M E1M 33M 34M 51G 51A 51T 52G 77G 78G)
N
2
230W Power Supply - AcBel China version (models 12C 12B 12H 12V
12Q 51Q)
74P4301
N
3
4
Pivot lock, 5.25 DASD (all models)
09N5747
40Y8801
*
CD-ROM Drive 48X - Black w/o jack & vol (models D1M 12M 12A
12C 12B 12H 12V 21M 12Q 14G 15G 24G 32G D2M E1M 51G 51A
51Q 51T)
**
4
4
4
CD-ROM Drive 48X - Black w/o jack & vol (models D1M 12M 12A
12C 12B 12H 12V 21M 12Q 14G 15G 24G 32G D2M E1M 51G 51A
51Q 51T)
40Y8805
40Y8807
40Y8813
**
**
**
CD-ROM Drive 48X - Black w/o jack & vol (models D1M 12M 12A
12C 12B 12H 12V 21M 12Q 14G 15G 24G 32G D2M E1M 51G 51A
51Q 51T)
CD-ROM Drive 48X - Black w/o jack & vol (models D1M 12M 12A
12C 12B 12H 12V 21M 12Q 14G 15G 24G 32G D2M E1M 51G 51A
51Q 51T)
Chapter 11. FRU lists 203
Item #
8178 FRUs
FRU#
CRU
4
CD-ROM Drive 48X - Black w/o jack & vol (models D1M 12M 12A
12C 12B 12H 12V 21M 12Q 14G 15G 24G 32G D2M E1M 51G 51A
51Q 51T)
40Y8929
**
4
DVD-ROM 16X/48X (Black) (models 16G 23G 31G 71G 72G 73G 74G
75G 76G 52G 77G 78G)
40Y8811
**
4
4
5
CD-RW Drive (48X/32X/48X) (models 13M 22M 33M)
Rambo IV (models 34M)
40Y8901
26K5383
40Y8757
**
**
*
Hard disk drive, 40 GB EIDE (models D1M 12M 12A 12C 12B 12H
12V 13M 21M 22M 12Q 14G 15G 24G 32G 71G 73G 75G D2M E1M
51G 51A 51Q 51T 77G)
5
Hard disk drive, 80 GB EIDE (models 16G 23G 31G 72G 74G 76G 52G
78G)
40Y8758
*
5
5
6
6
6
7
Hard disk drive, 80 GB S-ATA (models 33M 34M)
Hard disk drive, 80 GB S-ATA (models 33M 34M)
Diskette drive, 3.5 1.44 MB (all models)
71P7293
40Y8761
40Y9107
40Y8899
40Y9105
00N5151
*
*
**
**
**
*
Diskette drive, 3.5 1.44 MB (all models)
Diskette drive, 3.5 1.44 MB (all models)
Speaker assembly (models A1M D1M 12M 12A 12T 12C 12B 12H 12V
13M 21M 22M)
8
9
Pivot lock, 3.5 Diskette drive (all models)
Chassis/top cover kit (all models)
09N5748
88P5963
31P9121
*
**
*
10
256 MB SDRAM (models D1M 12M 12A 12C 12B 12H 12V 13M 12Q
14G D2M E1M)
10
256 MB SDRAM (models 21M 22M 15G 16G 23G 24G 31G 32G 71G
72G 73G 74G 75G 76G 51G 51A 51Q 51T 52G 77G 78G)
73P2683
*
10
11
512 MB SDRAM (models 33M 34M)
73P2684
19R0703
*
System board, 10/100 E-net (models 12M 12A 12C 12B 12H 12V 13M
21M 22M 12Q 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G
76G CTO-U CTO-G 33M 34M 51G 51A 51Q 51T 52G 77G 78G)
**
11
11
System board, (10/100 Enet) w/ video buffer -- optional to 19R0703
(models 12M 12A 12C 12B 12H 12V 13M 21M 22M 12Q 14G 15G 16G
23G 24G 31G 32G 71G 72G 73G 74G 75G 76G CTO-U CTO-G 33M
34M 51G 51A 51Q 51T 52G 77G 78G)
39J7965
**
**
System board, (10/100 Enet) w/ video buffer -- optional to 19R0703
(models 12M 12A 12C 12B 12H 12V 13M 21M 22M 12Q 14G 15G 16G
23G 24G 31G 32G 71G 72G 73G 74G 75G 76G CTO-U CTO-G 33M
34M 51G 51A 51Q 51T 52G 77G 78G)
41D0948
11
11
System board, 10/100 E-net, no AGP (models D1M D2M E1M)
19R0837
39J7966
**
**
System board, (10/100 Enet) w/ video buffer, no AGP -- optional to
19R0837 (models D1M D2M E1M)
11
System board, (10/100 Enet) w/ video buffer, no AGP -- optional to
19R0837 (models D1M D2M E1M)
41D0949
**
12
12
12
12
Intel Celeron 2.6 GHz (models D1M)
Intel Celeron 2.66 GHz (models D2M)
Intel Celeron 2.8 GHz (models E1M)
13R8907
19R0419
19R0421
19R0423
**
**
**
**
Intel Prescott P4 2.8 GHz (models 12M 12A 12C 12B 12H 12V 13M
12Q 14G)
204 Hardware Maintenance Manual
Item #
12
8178 FRUs
FRU#
CRU
**
Intel Prescott P4 2.8 GHz (models 15G 16G 71G 72G)
Intel Prescott P4 3.0 GHz (models 21M 22M 23G 24G 73G 74G)
Intel Prescott P4 3.2 GHz (models 31G 32G 75G 76G 33M 34M)
Intel Prescott P4 3.4 GHz (models 51G 51A 51Q 51T 52G 77G 78G)
Heat sink and fan, Northwood <3.0GHz (models D1M)
19R0292
19R0294
19R0296
29R6991
32P4004
13R9195
12
**
12
**
12
**
13
**
13
Heat sink and fan, Northwood >=3.0 GHZ and all Prescott (models
12Q 14G 15G 16G 71G 72G 23G 24G 73G 74G 31G 32G 75G 76G D2M
E1M 12M 12A 12C 12B 12H 12V 13M 21M 22M 33M 34M 51G 51A
51Q 51T 52G 77G 78G)
**
13
Heat sink and fan, Northwood >=3.0 GHZ and all Prescott, Dual Heat
Pipe -- optional to 13R9195 (models 12Q 14G 15G 16G 71G 72G 23G
24G 73G 74G 31G 32G 75G 76G D2M E1M 12M 12A 12C 12B 12H
12V 13M 21M 22M 33M 34M 51G 51A 51Q 51T 52G 77G 78G)
13N2951
**
Chapter 11. FRU lists 205
The FRUs listed in the following table are not illustrated.
8178 FRUs
FRU#
CRU
Retention kit (all models)
89P6740
89P6700
*
*
Fan bracket assembly (models 21M 22M 23G 24G 73G 74G 31G 32G 75G 76G 33M 34M
51G 51A 51Q 51T 52G 77G 78G)
System board EMC shield kit (all models)
Hard disk drive mounting bracket assembly (all models)
Heat Sink, Grease, Heat Pipe (all models)
Heat Sink, Dual Heat Pipe (all models)
Bezel kit (all models)
89P4761
88P5916
13R9195
13N2951
49P4371
49P4365
89P6749
88P5967
88P5971
88P6515
49P4530
00N5151
*
*
*
*
*
*
*
*
*
*
*
*
Cable, dual USB 2.0 (all models)
Cable, dual USB Cable, Long USB 2.0 (all models)
Cable, ATA66 1 drop (all models)
Cable, ATA66 2 drop (all models)
Cable, Diskette drive (all models)
Cable, second serial port (all models)
Speaker Asm (models D1M 12M 12A 12C 12B 12H 12V 13M 21M 22M 12Q 33M 34M 51G
51A 51Q 51T 52G 77G 78G D2M E1M)
Cable assembly, power/LED (all models)
5.25 EMC shield (all models)
Misc. hardware kit (all models)
Planar shield (all models)
37L5092
19K5548
88P5965
26K1216
33F8354
24P0383
89P5089
*
*
*
**
*
Battery, 3.0 V (all models)
Mouse, 2 button, black (models 11G)
*
Mouse, optical wheel (models D1M 12M 12A 12C 12B 12H 12V 13M 21M 22M 12Q 14G
15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G D2M E1M 33M 34M 51G 51A 51Q
51T 52G 77G 78G)
*
RJ11 connector adapter (Spain, Ireland) (All “G” models)
RJ11 connector adapter (Austria) (All “G” models)
RJ11 connector adapter (Belgium) (All “G” models)
RJ11 connector adapter (Denmark) (All “G” models)
RJ11 connector adapter (Norway, Finland) (All “G” models)
RJ11 connector adapter (France) (All “G” models)
RJ11 connector adapter (Germany) (All “G” models)
RJ11 connector adapter (UK, NZ, HK) (All “G”, “M”, “B”, “H” models)
RJ11 connector adapter (Italy) (All “G” models)
60H6043
60H6045
60H6046
60H6047
60H6048
60H6049
60H6050
60H6051
60H6052
60H6053
60H6054
60H6055
*
*
*
*
*
*
*
*
*
*
*
*
RJ11 connector adapter (Netherlands) (All “G” models)
RJ11 connector adapter (Sweden) (All “G” models)
RJ11 connector adapter (Switzerland) (All “G” models)
8178 Windows XP Pro Recovery CDs
FRU#
CRU
US (Models D1M 12M 12A 12H 13M 21M 22M 14G 15G 16G 23G 24G 31G 32G 71G 72G
73G 74G 75G 76G 12Q D2M E1M 33M 34M 51G 51A 51Q 51T 52G 77G 78G)
39J6414
*
206 Hardware Maintenance Manual
8178 Windows XP Pro Recovery CDs
FRU#
39J6415
39J6416
CRU
FR (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G 78G)
*
*
GR (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
IT (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G 78G)
SP (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G 78G)
39J6418
39J6417
39J6421
*
*
*
DK (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
NL (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
39J6424
39J6428
*
*
AE (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
SV (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G 78G)
39J6420
39J6425
*
*
HE (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
FI (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G 78G)
39J6422
39J6423
*
*
NO (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
PL (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G 78G)
39J6426
39J6432
*
*
PO (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
RU (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
41D1950
*
RE (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G 78G)
41D1949
39J6431
*
*
HU (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
CZ (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
39J6427
*
TR (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G 78G)
39J6430
39J6433
*
*
GK (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
SL (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G 78G)
39J6434
30R4813
30R4820
30R4827
39J7221
*
*
*
*
*
CS (models 12C)
Taiwan (models 12V)
HK (models 12B)
Multilingual 1 (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G
52G 77G 78G)
Multilingual 2 (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G
52G 77G 78G)
39J7222
*
8178 Keyboards (Standard PS/2 Black)
FRU#
CRU
US English (models D1M 12M 12A 12C 12H 13M 21M 22M 12Q 14G 15G 16G 23G 24G
31G 32G 71G 72G 73G 74G 75G 76G D2M E1M 33M 34M 51G 51A 51Q 52G 77G 78G)
89P8300
*
Arabic (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
89P8301
89P8302
*
*
Belgian/French (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G
52G 77G 78G)
Chapter 11. FRU lists 207
8178 Keyboards (Standard PS/2 Black)
FRU#
CRU
Bulgarian (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G
77G 78G)
89P8305
*
Chinese/US (models 12B 12V)
89P8306
89P8307
*
*
Czech (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
Danish (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
89P8308
89P8309
89P8310
89P8313
89P8314
89P8303
89P8315
89P8316
89P8317
89P8318
89P8319
89P8323
89P8324
89P8325
89P8326
89P8327
89P8328
89P8329
89P8330
89P8331
89P8332
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Dutch (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
French (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
German (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
Greek (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
Belgian/UK (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G
77G 78G)
Hebrew (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
Hungarian (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G
77G 78G)
Iceland (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
Italian 141 (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G
77G 78G)
Italian 142 (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G
77G 78G)
Norwegian (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G
77G 78G)
Polish (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
Portuguese (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G
77G 78G)
Romanian (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G
77G 78G)
Russian (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
Russian/Cyrillic (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G
52G 77G 78G)
Serbian/Cyrillic (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G
52G 77G 78G)
Slovak (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
Spanish (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G
78G)
Swedish/Finn (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G
52G 77G 78G)
208 Hardware Maintenance Manual
8178 Keyboards (Standard PS/2 Black)
FRU#
CRU
Swiss F/G (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G
77G 78G)
89P8333
*
Turkish 440 (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G
77G 78G)
89P8335
89P8336
89P8337
89P8338
89P8339
*
*
*
*
*
Turkish 179 (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G
77G 78G)
UK English (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G
77G 78G)
US Euro (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G 52G
77G 78G)
Yugoslav/Latin (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G 51G
52G 77G 78G)
8178 Power Cords
FRU#
CRU
Power Cord (models 12A 12V 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G
51G 51A 51T 52G 77G 78G)
6952301
*
Power Cord (ANZ) (models D1M 12M 13M 21M 22M D2M E1M 33M 34M)
13F9939
13F9978
*
*
Power Cord (EMEA, ANZ, ASEAN Eng, Korea) (models 14G 15G 16G 23G 24G 31G 32G
71G 72G 73G 74G 75G 76G 51G 52G 77G 78G)
Power Cord (EMEA, ANZ, ASEAN Eng, HK Eng) (models 12H 14G 15G 16G 23G 24G
31G 32G 71G 72G 73G 74G 75G 76G 51G 52G 77G 78G)
14F0032
13F9996
14F0068
*
*
*
Power Cord (EMEA) (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G
51G 52G 77G 78G)
Power Cord (EMEA, LA) (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G
76G 51G 52G 77G 78G)
Power Cord (China, HK) (models 12C 12B 12H)
02K0545
14F0086
*
*
Power Cord (EMEA) (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G
51G 52G 77G 78G)
Power Cord (EMEA, ANZ, ASEAN Eng) (models 14G 15G 16G 23G 24G 31G 32G 71G 72G
73G 74G 75G 76G 51G 52G 77G 78G)
14F0014
14F0050
49P2078
*
*
*
Power Cord (EMEA) (models 14G 15G 16G 23G 24G 31G 32G 71G 72G 73G 74G 75G 76G
51G 52G 77G 78G)
Power Cord (India) (models 12Q 51Q)
Chapter 11. FRU lists 209
Machine Type 8179
Item #
8179 FRUs
FRU#
CRU
ꢀ1ꢁ Side cover assembly (all models)
ꢀ2ꢁ ″L″ Cover assembly (all models)
ꢀ3ꢁ Front Bezel assembly (all models)
ꢀ4ꢁ Bezel trim/label kit (all models)
59P8547
59P8546
59P8544
49P1900
40Y8801
40Y8805
40Y8807
40Y8813
40Y8929
71P7357
26K5385
33P3301
40Y9107
*
**
*
*
ꢀ5ꢁ CD-ROM Drive 48X - Black w/o jack & vol (models 12C 13C)
ꢀ5ꢁ CD-ROM Drive 48X - Black w/o jack & vol (models 12C 13C)
ꢀ5ꢁ CD-ROM Drive 48X - Black w/o jack & vol (models 12C 13C)
ꢀ5ꢁ CD-ROM Drive 48X - Black w/o jack & vol (models 12C 13C)
ꢀ5ꢁ CD-ROM Drive 48X - Black w/o jack & vol (models 12C 13C)
ꢀ5ꢁ DVD-ROM 16X/48X (Black) (models)
*
*
*
*
*
*
ꢀ5ꢁ DVD-ROM 16X/48X (Black) (models)
*
ꢀ5ꢁ 48X Combo drive (models)
*
ꢀ6ꢁ Diskette drive, 3.5 1.44MB (all models)
*
210 Hardware Maintenance Manual
Item #
8179 FRUs
FRU#
CRU
ꢀ6ꢁ Diskette drive, 3.5 1.44MB (all models)
40Y8899
40Y9105
40Y8757
19R0703
39J7965
41D0948
19R0837
39J7966
*
ꢀ6ꢁ Diskette drive, 3.5 1.44MB (all models)
*
ꢀ7ꢁ Hard disk drive, 40GB EIDE (models 12C 13C)
*
ꢀ8ꢁ System board, 10/100 E-net (models 13C)
**
**
**
**
**
ꢀ8ꢁ System board, (10/100 Enet) w/ video buffer -- optional to 19R0703 (models 13C)
ꢀ8ꢁ System board, (10/100 Enet) w/ video buffer -- optional to 19R0703 (models 13C)
ꢀ8ꢁ System board, 10/100 E-net, no AGP (models 12C)
ꢀ8ꢁ System board, (10/100 Enet) w/ video buffer, no AGP -- optional to 19R0837
(models 12C)
ꢀ8ꢁ System board, (10/100 Enet) w/ video buffer, no AGP -- optional to 19R0837
41D0949
**
(models 12C)
ꢀ9ꢁ 256 MB SDRAM (models 12C)
31P9121
73P2683
19R0423
19R0292
13R9195
13N2951
74P4301
59P8542
*
ꢀ9ꢁ 256 MB SDRAM (models 13C)
*
ꢀ10ꢁ P4 2.8 GHz Prescott P4 (models 12C)
**
**
**
**
N
N
ꢀ10ꢁ P4 2.8 GHz Prescott P4 (models 13C)
ꢀ11ꢁ Heat sink and fan for Prescott (models 12C 13C)
ꢀ11ꢁ Heat sink and fan, Dual Heat Pipe -- optional to 13R9195 (models 12C 13C)
ꢀ12ꢁ Power supply, AcBel China, 230W (models 12C 13C)
ꢀ13ꢁ Chassis assembly (all models)
The FRUs listed in the following table are not illustrated.
8179 FRUs
Bezel blanks kit (all models)
FRU#
CRU
*
25P0068
25P0069
59P8564
00N5151
19K5548
03K9655
32P4743
22P4447
49P1750
49P1933
49P4365
59P8543
59P8549
59P8545
59P8548
59P8571
59P8572
59P8568
33F8354
Front bezel release kit (all models)
**
*
Retainer, Adapter Cards (all models)
Speaker assembly (models 13C)
*
5.25 EMC shield (all models)
**
*
Rubber foot (all models)
Universal adapter bracket (all models)
80 mm fan assembly (models with 3.06GHz microprocessor or greater)
2 audio front panel (models)
**
**
**
**
**
**
*
Cable, audio assembly (all models)
Cable, dual USB 2.0 (all models)
Hard disk drive bracket assembly (all models)
Hard disk drive tray (all models)
Power switch assembly (all models)
Bezel, Diskette drive (all models)
**
*
Cable, 2 drop (close spacing) ATA 66/100 w/pull tabs (all models)
Cable, 2 drop** (large spacing) ATA 66/100 w/pull tabs (all models)
Cable, Diskette drive (all models)
*
*
*
Battery, 3.0 V (all models)
*
Chapter 11. FRU lists 211
8179 FRUs
FRU#
CRU
Mouse, optical wheel (models 12C 13C)
Cable clip (all models)
89P5089
59P8584
89P4761
89P6740
13R9195
09N5764
60H6043
60H6045
60H6046
60H6047
60H6048
60H6049
60H6050
60H6051
60H6052
60H6053
60H6054
60H6055
*
*
System board EMC shield kit (all models)
**
N
**
**
*
Retention kit (all models)
Heatsink grease, Heat pipe (all models)
Misc. hardware kit (all models)
RJ11 connector adapter (Spain, Ireland) (All ″G″ models)
RJ11 connector adapter (Austria) (All ″G″ models)
RJ11 connector adapter (Belgium) (All ″G″ models)
RJ11 connector adapter (Denmark) (All ″G″ models)
RJ11 connector adapter (Norway, Finland) (All ″G″ models)
RJ11 connector adapter (France) (All ″G″ models)
RJ11 connector adapter (Germany) (All ″G″ models)
RJ11 connector adapter (UK, NZ, HK) (All ″G″, ″M″, ″B″, ″H″ models)
RJ11 connector adapter (Italy) (All ″G″ models)
RJ11 connector adapter (Netherlands) (All ″G″ models)
RJ11 connector adapter (Sweden) (All ″G″ models)
RJ11 connector adapter (Switzerland) (All ″G″ models)
*
*
*
*
*
*
*
*
*
*
*
8179 Windows XP Home Recovery CDs
FRU#
CRU
Simplified Chinese (models 12C)
30R4777
*
8179 Windows XP Pro Recovery CDs
FRU#
CRU
CS (models 13C)
30R4813
*
8179 Keyboards (Standard PS/2 Black)
FRU#
CRU
US English (models 12C 13C)
89P8300
*
8179 Power Cords
FRU#
CRU
Power Cord (China, HK) (models 12C 13C)
02K0545
*
212 Hardware Maintenance Manual
Chapter 12. Additional Service Information
This chapter provides additional information that the service representative might
find helpful.
Security features
Security features in this section include the following:
v Passwords
v Vital Product Data
v Management Information Format (MIF)
v Alert on LAN™
Hardware controlled Passwords
Hardware controlled passwords are set using the Setup Utility program. For more
information about passwords, see “Using passwords” on page 55.
Operating system password
An operating system password is very similar to a power-on password and denies
access to the computer by an unauthorized user when the password is activated.
The computer is unusable until the password is entered and recognized by the
computer.
Vital product data
Each computer has a unique Vital Product Data (VPD) code stored in the
nonvolatile memory on the system board. After you replace the system board, the
Management Information Format (MIF)
Management Information Format (MIF) is a file used to maintain a list of the
system unit serial number along with all serialized components (for example,
system board, riser card, memory, and processor).
At the time of computer manufacture, the EPROM is loaded with the serial
numbers of the system and all major components.
A company called Retain-a-Group is a central data warehouse offering serial
number data management. Retain-a-Group acts as a focal point to law
enforcement. The customer has the option to purchase serial number information
and services from Retain-a-Group. It is the customer’s responsibility to maintain
the MIF file and to inform Retain-a-Group of any changes to the file.
Some customers might request that their servicers assist them in maintaining the
MIF file when serialized components are replaced during hardware service. This
assistance is between the customer and the servicer. The servicer can use the DMI
MIF Browser to update the MIF information in the EPROM. It is anticipated that
some servicers might charge for this service.
To update the EPROM using the DMI MIF Browser, use the following procedure.
© Lenovo 2005. Portions © IBM Corp. 2005.
213
1. Click Start from the desktop, then Programs.
2. Select SystemView Agent
3. Select the Serial Number Information icon
4. Click the plus sign to expand.
5. Select the component you want to view or edit.
6. Double click on the component you want to change.
7. Enter new data in the Value field, then click Apply.
BIOS levels
An incorrect level of BIOS can cause false errors and unnecessary FRU
replacement. Use the following information to determine the current level of BIOS
installed in the computer, the latest BIOS available for the computer, and where to
obtain the latest level of BIOS.
v Current Level BIOS information
– Run the Setup Utility to determine the level of BIOS installed.
v Sources for obtaining the latest level BIOS available
1. Lenovo support web site:
http://www.lenovo.com/think/support/
2. Lenovo Customer Support Center
3. Levels 1 and 2 Support
Flash update procedures
This section details how to flash (update) the BIOS.
Updating (flashing) BIOS from a diskette or CD-ROM
1. Shut down the operating system and turn off the computer.
2. Insert the flash update diskette or CD-ROM.
3. Turn on the computer. The update begins.
4. When you are prompted to select a language, press the number on your
keyboard that corresponds to the language; then press Enter.
5. When prompted to change the serial number, press Y, type the seven character
serial number of your computer, and then press Enter.
6. When prompted to change the machine type/model, press Y, type the seven
character machine type/model of your computer, and then press Enter.
7. Follow the instructions on the screen to complete the update.
Updating (flashing) BIOS from your operating system
Note: Due to constant improvements being made to the Lenovo Web site, Web
page content (including the links referenced in the following procedure) is
subject to change.
1. From your browser, type http://www.lenovo.com/think/support.
2. In the Use Quick path field, type your 4-digit machine type and click Go.
3. Under Browse by product, click Downloads and drivers.
4. Scroll down to the BIOS catagory and click on the Flash Bios Update.
214 Hardware Maintenance Manual
5. On the Flash BIOS Update page, scroll down to locate the .txt file for the flash
from the operating system version. Click the .txt file.
6. Print these instructions. This is very important because these instructions are
not on the screen after the download begins.
7. From the browser, click Back to return to the list of files. Carefully follow the
printed instructions to download, extract, and install the update.
Recovering from a POST/BIOS update failure
Attention: If an interruption occurs during a POST/BIOS update (flash update),
the computer might not restart correctly. If this occurs, perform the following
procedure (also known as a Boot-block recovery).
Note: If your computer has no internal diskette drive, an optional USB diskette
drive must be connected to use the BIOS flash diskette.
1. Open the cover.
2. Remove any parts necessary to gain access to the Clear CMOS/Recovery
jumper.
3. Move the Clear CMOS/Recovery jumper from the standard position (pins 1
and 2) to pins 2 and 3.
4. Insert the BIOS flash diskette in the diskette drive.
5. Close the cover and reconnect the computer power cord to the computer and
to an electrical outlet. Turn on the computer.
6. The recovery session takes two to three minutes. During this time you will
hear a series of beeps. After the update session completes, the series of beeps
ends and the computer automatically turns off. There is no video during the
recovery session.
7. When the computer turns off, open the cover.
8. Move the Clear CMOS/Recovery jumper back to the original position (pins 1
and 2).
9. Remove the BIOS flash diskette from the diskette drive.
10. Close or install the cover and reconnect all external cables.
Chapter 12. Additional Service Information 215
Power management
Power management reduces the power consumption of certain components of the
computer such as the system power supply, processor, hard disk drives, and some
monitors.
Automatic configuration and power interface (ACPI) BIOS
Being an ACPI BIOS system, the operating system is allowed to control the power
management features of the computer and the setting for Advanced Power
Management (APM) BIOS mode is ignored. Not all operating systems support
ACPI BIOS mode.
Automatic Power-On features
The Automatic Power-On features within the Power Management menu allow you
to enable and disable features that turn on the computer automatically.
v Serial Port A Ring Detect: With this feature set to Enabled and an external
modem connected to serial port (COM1), the computer will turn on
automatically when a ring is detected on the modem.
v PCI Modem Ring Detect: With this feature set to Enabled, the computer will
turn on automatically when a ring is detected on the internal modem.
v PCI Wake Up: This feature allows PCI cards that support this capability to wake
the system.
v Wake Up on Alarm: You can specify a date and time at which the computer will
be turned on automatically. This can be either a single event or a daily event.
v Wake on LAN: If the computer has a properly configured token-ring or Ethernet
LAN adapter card that is Wake on LAN-enabled and there is remote network
management software, you can use the Wake on LAN feature. When you set
Wake on LAN to Enabled, the computer will turn on when it receives a specific
signal from another computer on the local area network (LAN).
216 Hardware Maintenance Manual
Recovering software using the Rescue and Recovery program
The Rescue and Recovery program provides an environment that runs
independently of the Windows operating system and is hidden from the Windows
operating system. Because the Rescue and Recovery workspace is hidden, it is
immune from most virus attacks and provides a safe place to perform rescue and
recovery operations that might not be possible in the Windows environment. The
following recovery solutions are provided by the Rescue and Recovery program:
v Create Product Recovery discs.
v Create rescue media.
v Back up your hard disk periodically.
v Create a Recovery Repair diskette.
If a problem with the software is encountered, you can use the recovery tools from
either the Windows environment or from the Rescue and Recovery workspace to
do one of the two recovery operations:
v Rescue files
v Restore your backups
Starting the Rescue and Recovery workspace
To start the program:
1. If your computer is already on when you start this procedure, shut down the
operating system and turn off the computer.
2. Repeatedly press the F11 key as you turn on the computer.
Note: If a user password or an administrator password has been set, the
Rescue and Recovery workspace is not displayed until you type the
password.
3. The Rescue and Recovery workspace is displayed.
Refer to the Quick Reference that comes with the computer and the Rescue and
Recovery help system for additional information about using the Rescue and
Recovery program.
Chapter 12. Additional Service Information 217
218 Hardware Maintenance Manual
Appendix. Notices
Lenovo may not offer the products, services, or features discussed in this
document in all countries. Consult your local Lenovo representative for
information on the products and services currently available in your area. Any
reference to a Lenovo product, program, or service is not intended to state or
imply that only that Lenovo product, program, or service may be used. Any
functionally equivalent product, program, or service that does not infringe any
Lenovo intellectual property right may be used instead. However, it is the user’s
responsibility to evaluate and verify the operation of any other product, program,
or service.
Lenovo may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you
any license to these patents. You can send license inquiries, in writing, to:
Lenovo (United States), Inc.
500 Park Offices Drive, Hwy. 54
Research Triangle Park, NC 27709
U.S.A.
Attention: Lenovo Director of Licensing
LENOVO GROUP LTD. PROVIDES THIS PUBLICATION “AS IS” WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some
jurisdictions do not allow disclaimer of express or implied warranties in certain
transactions, therefore, this statement may not apply to you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. Lenovo may make improvements
and/or changes in the product(s) and/or the program(s) described in this
publication at any time without notice.
The products described in this document are not intended for use in implantation
or other life support applications where malfunction may result in injury or death
to persons. The information contained in this document does not affect or change
Lenovo product specifications or warranties. Nothing in this document shall
operate as an express or implied license or indemnity under the intellectual
property rights of Lenovo or third parties. All information contained in this
document was obtained in specific environments and is presented as an
illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it
believes appropriate without incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those Web
sites. The materials at those Web sites are not part of the materials for this Lenovo
product, and use of those Web sites is at your own risk.
Any performance data contained herein was determined in a controlled
environment. Therefore, the result obtained in other operating environments may
© Lenovo 2005. Portions © IBM Corp. 2005.
219
vary significantly. Some measurements may have been made on development-level
systems and there is no guarantee that these measurements will be the same on
generally available systems. Furthermore, some measurements may have been
estimated through extrapolation. Actual results may vary. Users of this document
should verify the applicable data for their specific environment.
Television output notice
The following notice applies to models that have the factory-installed
television-output feature.
This product incorporates copyright protection technology that is protected by
method claims of certain U.S. patents and other intellectual property rights owned
by Macrovision Corporation and other rights owners. Use of this copyright
protection technology must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or disassembly is
prohibited.
Trademarks
The following terms are trademarks of Lenovo in the United States, other
countries, or both:
Lenovo
ThinkCentre
PS/2
Rescue and Recovery
The following terms are trademarks of International Business Machines
Corporation in the United States, other countries, or both:
Asset ID
Alert on LAN
IBM (used under license)
Wake on LAN
Intel and Pentium are trademarks of Intel Corporation in the United States, other
countries, or both.
Microsoft and Windows are trademarks of Microsoft Corporation in the United
States, other countries, or both.
Other company, product, or service names may be trademarks or service marks of
others.
220 Hardware Maintenance Manual
Part Number: 19R1295
Printed in USA
(1P) P/N: 19R1295
|