Motorola Nextel i365 User Manual

SouthernLINC

i365/i365IS Phone

User’s Guide

Dummy Page - To be discarded before printing

IMPORTANT NOTICE: PLEASE READ

PRIOR TO USING YOUR PHONE

The SIM card provided in this kit is intended for use

with the phone provided in this package.

Loss of certain features will result when using a SIM

card from one of the following models: i30sx, i35s,

i50sx, i55sr, i58s, i60c, i80s, i85s, i88s, i90c, i95cl

series, and the i2000 series.

For more information on SIM card compatibility, go to

www.motorola.com/iden.

Defects or damage to your Motorola phone that result

from the use of non-Motorola branded or certified

Accessories, including but not limited to replacement

housings and or other peripheral accessories, are

excluded from warranty coverage. Please refer to the

text of Motorola's Limited One Year warranty located

in this user’s guide for complete details.

harmful interference, and (2) this device must

accept any interference received, including

interference that may cause undesired

operation.

DECLARATION OF CONFORMITY

Per FCC CFR 47 Part 2 Section 2.1077(a)

Note: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation.

Responsible Party Name: Motorola, Inc.

Address: 8000 West Sunrise Boulevard

Plantation, FL 33322 USA

Phone Number: 1 (800) 453-0920

Hereby declares that the product:

Product Name: i365 (i365IS)

Model Number: H01XAN6JR5AN (i365)

H01XAN6JR6AN (i365IS)

If this equipment does cause harmful

interference to radio or television reception,

which can be determined by turning the

equipment off and on, the user is encouraged to

try to correct the interference by one or more of

the following measures:

Conforms to the following regulations:

FCC Part 15, subpart B, section 15.107(a),

15.107(d) and section 15.109(a)

•

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and

receiver.

Class B Digital Device

As a personal computer peripheral, this device

complies with Part 15 of the FCC Rules.

Operation is subject to the following two

conditions: (1) this device may not cause

•

Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician

for help.

HELLOMOTO

Introducing your new Motorola i365 wireless phone. Here’s a quick anatomy lesson.

Speaker On/Off

Key

Smart Key

Status Indicator

Earpiece

Volume Keys

Left Soft Key

Perform function

in lower left

Right Soft Key

Audio Jack

Perform function

in lower right

display.

PTT Button

Speaker

display.

Menu Key

From home screen,

open main menu.

Power Key

Home/End Key

End calls, exit menu

system.

Talk Key

Make &

answer calls.

Microphone

OK Key

4-Way

In menus & lists,

press to select

highlighted option.

Navigation Key

check it out

Home Screen

Main Menu

T u

Exit

Press the Navigation key

Press and hold the

up, down, left or right (

)

Power Key

for a

to highlight a menu feature.

few seconds, or until

the screen lights up,

to turn on your phone.

Press the O key

to select.

Press the O key

to open the

Ringtones screen

Motorola, Inc.

Manual Number: NNTN7437A

Consumer Advocacy Office

1307 East Algonquin Road

Schaumburg, IL 60196

www.hellomoto.com

Note: Do not ship your phone to the above address. If you need to

return your phone for repairs, replacement, or warranty service,

please contact the Motorola Customer Support Center at:

1-800-453-0920 (United States)

1-877-483-2840 (TTY/TDD United States for hearing impaired)

Certain mobile phone features are dependent on the capabilities

and settings of your service provider’s network. Additionally,

certain features may not be activated by your service provider,

and/or the provider's network settings may limit the feature’s

functionality. Always contact your service provider about feature

availability and functionality. All features, functionality, and other

product specifications, as well as the information contained in this

user's guide are based upon the latest available information and

are believed to be accurate at the time of printing. Motorola

reserves the right to change or modify any information or

specifications without notice or obligation.

MOTOROLA and the Stylized M Logo are registered in the US

Patent & Trademark Office. All other product or service names are

the property of their respective owners. Java and all other Java-

based marks are trademarks or registered trademarks of Sun

Microsystems, Inc. in the U.S. and other countries.

contents

check it out . . . . . . . . . . . 2

menu map. . . . . . . . . . . . 7

Use and Care . . . . . . . . . 9

call a stored phone

number or LINC ID . . . 19

your phone number

and LINC ID . . . . . . . . 20

text messages . . . . . . 20

manage memory . . . . 23

using your handset

navigation key. . . . . . . 49

handsfree speaker . . . 49

transmitters . . . . . . . . 49

use GPS with map

essentials . . . . . . . . . . . 10

about this guide . . . . . 10

SIM card. . . . . . . . . . . . 11

battery . . . . . . . . . . . . . 11

turn it on & off . . . . . . 15

enable security. . . . . . 15

make a phone call. . . . 16

answer a phone call . . 16

make a InstantLINC

Mobile to Mobile call . 16

answer a InstantLINC

Mobile to Mobile call . 18

store a phone number

software . . . . . . . . . . . 50

calls . . . . . . . . . . . . . . . . 53

turn off a call alert. . . . 53

recent calls . . . . . . . . . 53

redial. . . . . . . . . . . . . . 54

caller ID . . . . . . . . . . . 54

call forward. . . . . . . . . 55

voice names . . . . . . . . 55

emergency calls . . . . . 56

international calls . . . . 57

speed dial . . . . . . . . . . 57

turbo dial. . . . . . . . . . . 57

voicemail. . . . . . . . . . . 57

LINCaround . . . . . . . . 58

as a modem . . . . . . . . 24

main attractions . . . . . . 26

LINC features . . . . . . . 26

one touch PTT . . . . . . 33

LINC manager . . . . . . 34

bluetooth^®. . . . . . . . . 34

advanced features . . . 38

basics. . . . . . . . . . . . . . . 45

display . . . . . . . . . . . . 45

main menu . . . . . . . . . 46

text entry . . . . . . . . . . 46

or LINC ID. . . . . . . . . . 18

contents

customize. . . . . . . . . . . . 65

ring tones . . . . . . . . . . 65

wallpaper. . . . . . . . . . . 66

backlight . . . . . . . . . . . 67

datebook . . . . . . . . . . . 67

hide or show location

Specific Absorption

Rate Data . . . . . . . . . . . . 85

Motorola Limited Warranty

for the United States

and Canada . . . . . . . . . . 87

Information From the

World Health

information . . . . . . . . . 68

other features . . . . . . . . 70

advanced calling . . . . . 70

contacts. . . . . . . . . . . . 71

datebook . . . . . . . . . . . 71

GPS . . . . . . . . . . . . . . . 72

handsfree . . . . . . . . . . 73

personalize . . . . . . . . . 74

pc applications. . . . . . . 74

TTY . . . . . . . . . . . . . . . 74

security . . . . . . . . . . . . 75

Organization . . . . . . . . . 92

Patent and Trademark

Information . . . . . . . . . . 94

Privacy and Data

Security . . . . . . . . . . . . . 95

Smart Practices

While Driving . . . . . . . . . 96

index. . . . . . . . . . . . . . . . 98

Safety and General

Information . . . . . . . . . . 78

Service & Repairs . . . . . 84

contents

menu map

main menu

Settings

Shortcuts

Recent Calls

Memo

•

(see next page)

•

[New Entry]

1)Shortcuts

Downloads

2)Cntcs[New Contact]

3)Ring Tones

4)LINC Manager

5)Browser Apps

6)Java Apps

Contacts

Browser Apps

•

[New Contact]

Java Apps

Messages

•

[Create Message]

•

Java System

Voice Mail

Text Inbox

Quick Notes

Drafts

7)Settings

Ring Tones

8)Profiles

•

Vibrate All

9)Call Forward

Ringer

Vibrate

Silent

Profiles

Text Outbox

Net Alert

Fax Mail

Call Alert

LINC Manager

Call Timers

GPS

•

LINC Message

•

Last Call

LINC Picture

LINC Event

LINC My Info

LINC Contact

Configure

•

Position

Privacy

Interface

Phone Reset

Phone Lifetime

Prvt/Grp Reset

Prvt/Grp Life

Circuit Reset

Circuit Lifetime

Kbytes Reset

Bluetooth

•

Hands Free

Link to Devices

Device History

Setup

My Pictures

Call Forward

My Info

Find Me

VoiceRecord

•

My Name

LINCaround

Line 1

•

[New VoiceRec]

Line 2

LINC ID

Group ID

Carrier IP

IP1 Address

IP2 Address

Circuit Data

Datebook

This is the standard Main Menu layout. Your

phone’s menu may be a little different.

menu map

settings menu

Display/Info

InstantLINC

Security

•

Wallpaper

Text Size

•

Tkgrp Silent

•

Phone Lock

Tkgrp Area

Keypad Lock

SIM PIN

Theme

One Touch PTT

Alert Type

Home Icons

Backlight

Clock

Menu View

Large Dialing

Status Light

Language

GPS PIN

LINC Notes

On/Off LINC Features

Store Rcvd Info

Change Passwds

Advanced

•

Alert Timeout

Personalize

Headset/Spkr

Connectivity

Reset Defaults

Return to Home

Transmitters

Phone Only

•

Menu Options

Up Key

Phone Calls

Down Key

Left Key

Right Key

Center Key

Left Sftkey

Right Sftkey

Power Up

•

Set Line

Any Key Ans

Auto Redial

Call Waiting

Auto Ans

Baud Rate

Minute Beep

Call Duration

TTY

Notifications

DTMF Dialing

Volume

•

Line 1

Line 2

Messages

Earpiece

Speaker

Keypad

Java Earpiece

Java Spkr

Data

menu map

Use and Care

To care for your Motorola phone, please keep it away from:

liquids of any kind

dust and dirt

Don’t expose your phone to

water, rain, extreme humidity,

sweat, or other moisture.

Don’t expose your phone to

dust, dirt, sand, food, or other

inappropriate materials.

extreme heat or cold

cleaning solutions

Avoid temperatures below

-10°C/14°F or above 45°C/113°F.

To clean your phone, use only a

dry soft cloth. Don’t use alcohol

or other cleaning solutions.

microwaves

the ground

Don’t try to dry your phone in a

microwave oven.

Don’t drop your phone.

Use and Care

essentials

Caution: Before using the phone for the first

time, read the Important Safety and Legal

information included in the gray-edged pages

at the back of this guide.

Press the navigation key

Phone Calls, and press the center key

select it.

to scroll to

symbols

This means a feature is network or

subscription dependent and may

not be available in all areas. Contact

SouthernLINC Wireless for more

information.

about this guide

This guide shows how to locate a menu

feature as follows:

Find it:

Phone Calls

This means a feature requires an

optional accessory.

This means that, from the home screen:

Press the menu key

to open the

Settings menu.

essentials

Warning: To avoid loss or damage, do not

remove your SIM card from your phone

unless absolutely necessary.

SIM card

insert the SIM card

Turn off your phone and remove your battery

before you install or remove a SIM card.

battery

Carefully slide the SIM card into your phone,

until it lies flat in the SIM card holder.

Battery Use & Battery Safety

•

Motorola recommends you always

use Motorola-branded batteries and

chargers. The warranty does not cover

damage caused by non-Motorola

batteries and/or chargers.

Caution: Use of an unqualified battery

or charger may present a risk of fire,

explosion, leakage, or other hazard.

Improper battery use, or use of a

damaged battery, may result in a fire,

explosion, or other hazard.

•

Battery usage by children should be

supervised.

essentials

•

Important: Motorola mobile devices

are designed to work best with

qualified batteries. If you see a

message on your display such as Invalid

Battery or Unable to Charge, take the

following steps:

temperature. Never expose batteries to

temperatures below 0°C (32°F) or

above 45°C (113°F) when charging.

Always take your mobile device with

you when you leave your vehicle.

•

When storing your battery, keep it in a

cool, dry place.

•

Remove the battery and inspect it to

confirm that it bears a Motorola

“Original Equipment” hologram;

It is normal over time for battery life to

decrease, and for the battery to exhibit

shorter runtime between charges or

require more frequent or longer

charging times.

•

If there is no hologram, the battery

is not a qualified battery;

If there is a hologram, replace the

battery and retry charging it;

•

Avoid damage to battery and mobile

device. Do not disassemble, open,

crush, bend, deform, puncture, shred,

or submerge the battery or mobile

device. Avoid dropping the battery or

mobile device, especially on a hard

surface. If your battery or mobile

device has been subjected to such

damage, take it to a Motorola

If the message remains, contact a

Motorola Authorized Service Center.

•

New batteries or batteries stored for a

long time may take more time to

charge.

Charging precautions: When charging

your battery, keep it near room

essentials

Authorized Service Center before

using. Do not attempt to dry it with an

appliance or heat source, such as a hair

dryer or microwave oven.

battery installation

Rotate the release lock counter-

clockwise until it releases the battery

door.

•

Use care when handling a charged

battery: Particularly when placing it

inside a pocket, purse, or other

container with metal objects. Contact

with metal objects (e.g., jewelry, keys,

beaded chains) could complete an

electrical circuit (short circuit), causing

the battery to become very hot, which

could cause damage or injury.

Remove the battery door.

Promptly dispose of used batteries in

accordance with local regulations.

Contact your local recycling center for

proper battery disposal.

Warning: Never dispose of batteries in a fire

because they may explode.

essentials

battery charging

New batteries are not fully charged.

Push the battery down until it snaps in

place.

charge using the charger

Pull out the

connector cover, and

insert the charger

into the accessory

connector on your

phone as shown.

Replace the battery door and press it

gently until you hear a click.

Plug the other end

of the charger into

the appropriate

electrical outlet.

When you charge the

battery, the battery level indicator at the upper

right of the screen shows charging progress.

At least one segment of the indicator must be

visible to ensure full phone functionality while

charging.

essentials

Tip: Motorola batteries have circuitry that

protects the battery from damage from

overcharging.

To turn off your phone, press and hold

two seconds.

for

Note: If you press the

for more than four

seconds, the handset will power “On” in

Transmitters Off mode. To avoid deactivating the

phone’s transmitters when powering up, hold

the power key for less than 4 seconds. To

power up the phone normally from charging

mode, wait until the Charger Attached screen is

displayed, and then press the power key. See

“transmitters” on page 49.

Note: This handset complies with

environmental energy consumption

requirements by notifying the user to unplug

the charger from the power outlet when the

charger is disconnected from phone/power

outlet. This notice can be dismissed

permanently by pressing

under No.

turn it on & off

To turn on your

enable security

You must enable security the first time you

power on you phone or within 10 days of first

activation of your phone.

phone, press and hold

for a few seconds

or until the display

turns on. If prompted,

enter your four-digit

unlock code.

Press

under Ok.

Your are prompted to enable security.

Press

under Yes. A series of screens

essentials

followed by the default home page

displays.

If you want to answer the call using the

handset, press . To hang up press

Press

to return to the home screen.

If you are using a Bluetooth headset, you

can press the answer key on your

Bluetooth headset. To hang up press the

same key on your Bluetooth.

make a phone call

Enter a phone number and press

to make

a call or use a voice command. See “place a

call using voice name” on page 55.

make a InstantLINC

Mobile to Mobile call

With InstantLINC Mobile to Mobile calls, you

use your phone as a long-range, digital 2-way

radio using one-to-one InstantLINC Mobile to

Mobile calls or one-to-many Talkgroup calls.

Tip: For best performance avoid touching the

antenna with your fingers during the call.

To hang up press

answer a phone call

When your phone rings and/or vibrates, you

have the following options:

Your LINC ID is the number at which you

receive one-to-one InstantLINC Mobile to

Mobile calls.

If you want to answer the call on speaker

phone, press the speaker key . To hang

Talkgroup numbers are numbers through

which you receive one-to-many group calls.

)

up press the smart key

essentials

to make a InstantLINC Mobile to Mobile

call

The recipient has the following options:

Option

Enter the LINC ID you want to call.

Answer: Begin a InstantLINC Mobile to

Mobile call with the sender.

Press and hold the PTT button. Begin

talking after your phone emits a chirping

sound.

Queue: Store the call alert to the call alert

queue.

Release the PTT button to listen.

Clear: Dismiss and delete the call alert.

To end the call press

to send a call alert

Note: An InstantLINC Mobile to Mobile call

ends automatically if there is no activity on

the call for a few seconds.

Enter the LINC ID you want to call as you

would when making a InstantLINC Mobile

to Mobile call.

send call alerts

Press

under Alert.

Sending a call alert discretely lets the

recipient know that you want to talk to him or

her on a InstantLINC Mobile to Mobile call.

When the message Ready To Alert appears on

the display, press the PTT button until the

message Alert Successful appears.

When you send a call alert, the recipient’s

handset displays your name and emits a

series of beeps or vibrations.

essentials

to answer a call alert

answer a InstantLINC

Mobile to Mobile call

Press the PTT button to start a

InstantLINC Mobile to Mobile call with the

sender.

When your phone emits a chirping sound

or vibrates to indicate you are receiving a

InstantLINC Mobile to Mobile call, wait for

the caller to finish speaking.

Queue the call allert by pressing

under

Queue

Press and hold the PTT button and begin

talking after your phone emits a chirping

sound.

Clear the call alert by pressing

under

Clear

Release the PTT button to listen.

store a phone number

or LINC ID

To end the call press

answer a call alert

You can store a phone number or LINC ID in

When you receive a call alert, you must

answer, queue, or clear it. You cannot receive

phone calls or InstantLINC Mobile to Mobile

calls until you do.

Contacts.

Find it:

[New Contact].

Enter a name for the new entry. Each

entry’s name can contain 20 characters.

Select a specific Ringer

essentials

Select a type for the entry (Mobile

LINC ID

Find it:

Work1

HUB

LINC ID

Work2

Home

Fax

Pager

Talkgroup,

Scroll to the Contacts entry.

IP or Other). To store a LINC ID choose

Tip: By pressing the first letter of the

name of the Contacts you want, you will be

taken to all the contact names starting

with the letter you pressed.

Enter the number for the entry and press

under Done

Tip: Before saving the entry, you can save

more information. You can store an Email

address, IP addresses, and more. You can

also choose a special ringer.

If the Contacts entry contains more than

one number, scroll left or right until the

type of the number you want to call is

displayed (Mobile LINC ID, Work1, Work2, Home,

After you have saved the number, the new

Contacts entry is displayed.

etc.).

If you chose a phone number, press

call the entry.

call a stored phone

number or LINC ID

If you chose a LINC ID or Talkgroup ID,

press and hold the PTT button to call the

number.

Shortcut: From the home screen press

under Contcs

Tip: If the Contacts entry you scrolled to

contains a LINC ID, you can make an

essentials

InstantLINC Mobile to Mobile call to that LINC

ID by pressing and holding the PTT button,

even if the LINC ID is not the type of number

displayed.

set it up

Before you begin using text messaging, you

may need to set up your signature, service

center number, and expiration information.

Shortcut: From the home screen press

your phone number and

LINC ID

under Mesg

Text Inbox

Text Msg Setup

Find it:

My Info.

Find it:

Text Inbox

Text Msg

Setup

Tip: Want to see your phone number or LINC

ID while you’re on a call? Press

My Info.

The following options become available:

option

text messages

Your phone sends text messages using

Signature: Enter your signature (up to 11

characters long).

Mobile Originated Short Messaging Services

(MOSMS) and receives text messages from

other phones that are using MOSMS.

Delivery Rpt: Set it to On if you wish to receive a

report once the message has been

delivered.

essentials

To dismiss the message notification press

under Back

option

Srvc Cntr No: Enter the phone number of your

service center. If you do not know this

number, contact SouthernLINC Wireless.

Note: If your phone is powered off when you

receive a text message, your phone notifies

you the next time you power it on. If you are

out of your coverage area, your phone alerts

you when you return to your coverage area.

Expire After: This is the amount of time

messages you send are saved at the

service center if they cannot be delivered.

After this period, they are discarded.

Tip: While reading a text and numeric

message that contains a phone number, you

can press

Cleanup: Set this option to On if you want your

phone to delete sent messages.

to call that number.

If you select Cleanup, select Clean Up After to set

the number of days after which sent

messages are deleted or the number of

messages to be kept.

read from the Message center

From the home screen press

under

Mesg

Text Inbox.

Select the message you want to read or

press the number of the message you

want to read. If the message fills more

than one screen, scroll to read it.

Press

you entered.

under Done to save the information

receive a text message

Tip: Scrolling through one message lets

you view the next message.

To view the message press

under Read.

essentials

To reply to the message, press

under

Press

Set Send Method and select Text

Reply or to see all other choices, including

forwarding and deleting the message,

calling the sender, or storing the sender’s

Fax,

x400

Paging Email ERMES, or Voice

If you want to send the message, press

under Send or to delete the message

without sending it, press under Cancel

number in Contacts, press

Note: If you want to request confirmation

of delivery press

create and send text messages

Delivery Report

On.

From the home screen press

under

Mesg

[Create Message].

use drafts

When you save a message as a draft, it is

saved in the drafts folder.

You can also create a text message from

the Text Inbox Text Outbox, or Drafts.

Shortcut: From the home screen press

under Mesg

To address the message use the keypad

to enter the phone number of the person

you want to send the message to and

Drafts.

Select the draft you want to edit. You also

have the choice to create new text

messages from this menu.

press

Select Msg and enter the text of the

message or to use a quick note press

under Browse and scroll to the quick note

To edit the fields you want to change,

follow step 2 through step 5 in “create

and send text messages” above.

you want and press

essentials

Press

under Yes to confirm.

resend text messages

Shortcut: From the home screen press

manage memory

Your text inbox, outbox, and drafts folder have

a set amount of memory available for storing

messages.

under Mesg

Text Outbox.

Scroll to the message you want to resend

or press the number of the message you

want to resend.

The text inbox holds 20 messages. If the text

inbox is full, you cannot receive messages

until you delete some.

Press

Re-send.

delete sent text messages

Shortcut: From the home screen press

The outbox and drafts folder hold 30

messages each. If the outbox and drafts

folder memory is full, you cannot send

messages or save drafts until you delete

some.

under Mesg

Text Outbox.

Scroll to the message you want to delete.

Press

under Delete

To view the amount of memory available in

your text inbox, text outbox, or drafts folder:

under Yes to confirm.

delete all unlocked sent messages

Shortcut: From the home screen press

From the idle screen press

under Mesg

Scroll to the folder whose available

memory capacity you want to view.

under Mesg

Text Outbox

Press

Delete All.

Press

under Memory.

essentials

outlined in the device’s user guide to connect

the device to your handset.

using your handset

as a modem

You can use your handset as a modem (Packet

Data only) with a laptop, handheld device, or

desktop computer. Circuit Data is not

supported. In order to use your handset as a

modem, you must create either a wired or

wireless connection between your handset

and the other device.

When used as a modem, your handset is

enabled for Data Modem transfer mode, which is

used for small file transfers such as email.

Note: To use these services, you must install

the iDEN Wireless Data Services software

(available separately). For more information on

setting up your computer and your handset

for Packet Data calls, contact SouthernLINC

Wireless.

To connect your handset wirelessly, you must

have a Bluetooth adapter for the other device.

connect via Bluetooth

Use your handset as a modem via Bluetooth.

The laptop, handheld device, or desktop

computer you want to connect to must have a

Bluetooth adapter installed.

Check that the adapter is properly installed,

and then follow the specific instructions

essentials

main attractions

the LINC ID you are engaged in a InstantLINC

Mobile to Mobile call with, LINC IDs on the

LINC features

With LINC features, your phone can send and

receive the following items through

InstantLINC Mobile to Mobile calls with other

phones that have this capability:

Recent Calls list, and LINC IDs stored in Contacts

When you make or receive a InstantLINC

Mobile to Mobile call, your phone

automatically determines whether the phone

you are engaged in a InstantLINC Mobile to

Mobile call with is able to receive each of

these items. Your phone saves this

•

Short text messages¹

Pictures¹

Datebook events

My Info

information for as long as the LINC ID is on

your Recent Calls list or is saved in your Contacts

Your phone updates the saved information

each time you make or receive a call to or

from that LINC ID.

Contact information

You can choose to send messages, pictures,

events, My Info, or Contacts information to

You can turn your phone’s ability to send and

receive messages, pictures, or events

information On and Off.

1. Additional charges may apply.

main attractions

Note: You cannot send LINC feature items

during Talkgroup calls.

Contacts list, the Recent Calls list, or from the LINC

Manager

begin a message during a InstantLINC

Mobile to Mobile call

While in a InstantLINC Mobile to Mobile call,

send messages

Note: This feature requires a

subscription. Please contacts your sales

representative or SouthernLINC Wireless at

1-800-406-0151.

press

LINC Features

LINC Message.

Note: The first time you send a message,

Messaging Fees May Apply. Continue? appears and you

The LINC Messages feature lets you send

short text messages through InstantLINC

Mobile to Mobile calls.

are prompted to respond. Press

to acknowledge the message.

under Yes

begin a message from the Contacts or

the Recent Calls list

When you send a message, it appears on the

display of the phone you are engaged in the

InstantLINC Mobile to Mobile call with.

From the Contacts or the Recent Calls list,

select the entry containing the LINC ID

you want to send the message to.

begin a message and choose a

recipient

Press

LINC Features

LINC Message.

You can begin a message during a

InstantLINC Mobile to Mobile call, from the

main attractions

begin a message from the LINC

Manager

changes the Quick Note for this message only

and will not change the Quick Note on the list.

The LINC Manager lets you select the LINC ID you

want to send the message to from Contacts or

the Recent Calls list.

send a completed message

After you have completed your message,

press the PTT button to send it.

Find it:

LINC Manager

LINC Message.

Then select A Contact or A Recent Call to see a list

of entries from the Contacts or the Recent Calls list

that can receive messages.

receive messages

When you receive a message, a message

notification appears on the display.

create messages

To view the message press

under View

After you have begun a message and chosen

a recipient, a screen appears that lets you

create the text of the message you want to

send. Your message may be up to 400

characters long.

To dismiss the message press

under

Dismiss

reply to a message

View the message.

Press under Reply

You can choose from a list of ready-made

words or short phrases called Quick Notes.

You can use a Quick Note as it is or edit it

before you send it. Editing a Quick Note

Create the message and press the PTT

button to send it.

main attractions

send pictures

send a picture during a call

Note: This feature requires a

While in a InstantLINC Mobile to Mobile

subscription. Please contacts your sales

representative or SouthernLINC Wireless at

1-800-406-0151.

call, press

LINC Features

under Picture or press

LINC Picture

A list of pictures that can be included in a

InstantLINC Mobile to Mobile call

appears.

You can send pictures stored in the My Pictures

through InstantLINC Mobile to Mobile calls.

The picture you send appears on the Private

call recipient’s display.

Select the picture you want to send.

Press the PTT button to send the picture.

If the recipient accepts the picture, their

phone saves the picture. The picture then

appears in that phone’s recent call list.

Wait while the picture is transmitted. The

InstantLINC Mobile to Mobile call is

temporarily interrupted while a picture is

transmitted.

The first time you send a stored picture after

turning the phone on, Picture Fees May Apply.

Continue? appears and you are prompted to

respond. You are charged only once for that

picture.

When prompted, press the PTT button to

resume the InstantLINC Mobile to Mobile

call.

Note: After you send or receive a picture via

PTT with a user, that picture will be displayed

every time you are in a private call with that

Note: You cannot make or receive

InstantLINC Mobile to Mobile calls while

transmitting or receiving a picture.

main attractions

user. That picture is saved in the media center

and a link is created between that contact and

the picture.

When prompted, press the PTT button to

resume the InstantLINC Mobile to Mobile

call.

Note: Pictures sent or received may be up to

130x130 in size and up to 100 kb.

from the LINC Manager:

Find it: LINC Manager LINC Picture

Select A Contact or A Recent Call

start a call by sending a picture

A list of contacts that have LINC IDs and

are able to receive pictures appears.

from My Pictures:

Find it:

My Pictures

Select the name of the person you want

to send the picture to.

Select the picture you want to send.

Press

Select A Contact or A Recent Call

LINC View.

Select the picture you want to send.

Press the PTT button to send the picture.

A list of contacts that have LINC IDs and

are able to receive pictures appears.

Once picture has been sent, when

prompted press the PTT button to resume

the call.

Select the name of the person you want

to send the picture to.

Press the PTT button to send the picture.

main attractions

receive a picture

clear a picture from the display

When someone sends you a picture, your

phone emits a tone or vibrates and a message

appears asking if you want to accept the

picture.

If you want to clear a picture from your

phone’s display while still on a call, press

Clear Screen.

The picture will not appear on the display

Pictures you receive are saved to your phone’s

memory. They are accessible through My

again the next time you receive a call from

person who sent it. This does not delete the

Pictures

picture from My Pictures.

When you see a message asking if you want

to accept the picture, press Yes to accept or No

to decline.

send my info

While in a InstantLINC Mobile to Mobile

Call press LINC View My Info, and push

the PTT button to send.

Tip: If you want to stop the transmission

before it is finished, press

Note: The first time you accept a stored

picture after turning the phone on, Picture Fees

May Apply. Continue? appears and you are

From the home screen press

My Info

LINC View My Info and push the PTT

prompted to respond. Press

accept the picture.

under Yes to

button to send.

main attractions

set my info sending option

Select On or Off.

You can control what portion of the

information in My Info is sent and whether it is

sent automatically in every call or only when

you choose to send it.

When you make a call in which your

information is sent automatically, the

name you entered in the My Name field of

My Info appears on the display of the

recipient’s phone, even if your name and

LINC ID are not stored in the recipient’s

Contacts.

Find it:

LINC Manager

Configure LINC My Info

Info to Send.

Select or remove the fields you want to

send.

send contact information

Press

under Done.

While in a InstantLINC Mobile to Mobile

call press

LINC Features.

The information your phone sends always

includes My Name and LINC ID. You may also send

Select LINC Contact and select the contact

information you want to send.

Line 1 Line 2, Carrier IP, and Circuit Data, depending

on your sending options.

Push the PTT button to send.

automatic sending

To control whether you send your information

automatically:

From the home screen press

LINC

Manager > LINC Contact

Find it:

LINC Manager

Configure LINC My Info

Auto Send

main attractions

Enter the LINC ID number of the person

you want to send the Contact information

one touch PTT

Find it:

LINC Manager

Configure

One Touch

to or press

under Browse

PTT.

Select from Recent Calls

Contacts, or Memo.

One Touch PTT sets your phone to do any of

the following each time you press the PTT

button from the home screen:

Select the contact information you want

to send and push the PTT button.

turn PTT features on and off

option

Off: Nothing happens when you press the

PTT button from the home screen.

You can turn your phone’s ability to send and

receive messages, pictures, and datebook

events on and off.

Last Call: Call the most recent LINC ID or

Group on the recent calls list.

You cannot turn your phone’s ability to send

and receive My Info and contact information

on and off.

Assigned No.: Call a LINC ID you assign. Enter

the number using your keypad, or press

under Search. Select Contacts

Memo

Recent Calls, or

Find it:

LINC Manager

Configure

On/Off LINC

Features

Check or uncheck Messages

Events

If you are entering a Talkgroup number,

press before the number.

Pictures and/or

LINC Manager: Go to LINC Manager. See “LINC

manager” on page 34.

main attractions

Select LINC Message, LINC Picture, LINC Event, LINC

My Info, or LINC Contact. After choosing what

PTT item you are sending, select a

option

LINC Message: Go to the first screen to send a

message. See “send messages” on

page 27.

contact and press the PTT button to send.

LINC Picture: Go to the first screen to send

pictures. See “send pictures” on page 29.

Select Configure to configure your LINC Notes

LINC My Info One Touch PTT, or On/Off LINC Features

LINC Event: Go to the first screen to send a

datebook event.

bluetooth

LINC My Info: Go to the first screen to send My

Info. See “send my info” on page 31.

Your handset supports the use of wireless

Bluetooth headsets.

LINC Contact: Go to the first screen to send a

contact. See “send contact information” on

page 32.

Find it:

Bluetooth.

turn Bluetooth On or Off

You can turn your phone’s Bluetooth feature

on or off. While Bluetooth power is on, your

phone can communicate with other devices.

LINC manager

The LINC Manager lets you quickly access LINC

features, and other InstantLINC Mobile to

Mobile call features, from the main menu.

Find it:

Bluetooth

Setup

Power.

Find it:

LINC Manager

Select On to power Bluetooth On.

main attractions

Select Name if you wish to assign a name

to your handset.

the name of the Bluetooth headset on

your screen.

Select Find Me Time to determine the

amount of time in which your handset can

be found by other Bluetooth devices.

Your handset requires that you create a

bond in order to connect with a Bluetooth

headset. Press

under Yes when you

are prompted to bond with the headset.

Tip: You can turn off Bluetooth if you want to

prolong battery life or if you enter an area

where Bluetooth is prohibited.

Enter the Bluetooth pass key.

Some Bluetooth devices ship with

Bluetooth PINs. Please refer to your

Bluetooth device’s user guide to locate

this information.

make a Bluetooth connection

connect your handset with a Bluetooth

headset

If a device ships without a Bluetooth PIN,

then you can enter any PIN for that

device. To establish a connection to that

device, enter the same PIN for both your

phone and the device. For example, if you

enter 1234 as the device’s PIN, then enter

1234 as your phone’s PIN.

Find it:

Bluetooth

Hands Free [Find Devices].

Follow the instructions on your Bluetooth

headset to set it up to be found.

Once your Bluetooth headset is set to be

found press

phone will scan the Bluetooth headset

until it finds it. Press when you see

on your handset. Your

Press

under Ok.

main attractions

Note: This handset offers bluetooth auto pair

feature with auto pair compatible Motorola

devices. When bonded via bluetooth with a

certain device, the pin will not be required

Note: If the Handsfree Devices list contains only

one device, then your phone will automatically

try to connect to that device.

While in a call, press

Press under Yes to power On

Bluetooth.

Select the audio device you want to

connect to from the list of Handsfree Devices

Use Bluetooth.

connect your handset with another

Bluetooth device

Find it:

Bluetooth Link To Devices.

Select the device you want from the list of

found devices on your screen.

send information via Bluetooth

You can use your handset to send contacts

entries, or datebook events to another

Bluetooth device.

Create a bond if you are prompted to do

so.

Tip: If you have previously connected to a

device, the device will be stored on your

phone so you can connect with it easily.

The receiving device must be within 32 feet

(10 meters) of your phone in order to connect

with yours.

use Bluetooth during a call

Note: Files sent or received may be up

to 200 kb.

You can connect with available Bluetooth

devices during a call.

main attractions

send Contacts

Shortcut: From the home screen press

Select the datebook event you want to

send.

under Contcs

Press

Send Via...

Bluetooth.

Select the contact you want to send.

If the event you select repeats, then you

will be prompted to choose whether to

send the selected instance of the event or

all instances of the event.

Press

Send Via...

Bluetooth.

Press

under Yes to power On

Bluetooth.

To send only the selected instance of the

Select the device you want to transfer the

contact information to.

event, select This Event Only

To send all instances of the event, select

Search for the device by selecting [Find

Repeat Events

Devices]

Press

under Yes to power On

If prompted, bond with the device.

Bluetooth.

Your phone connects with the devices and

transfers the contact.

Select the device you want to transfer the

contact information to.

send a Datebook event

Find it: Datebook

main attractions

Search for the device by selecting [Find

service provider’s customers. A hub consists

of 1 to 4 Talkgroups.

Devices]

If prompted, bond with the device.

You must join a Talkgroup to make or receive

calls on that Talkgroup. On your phone, you

join a Talkgroup by joining the hub it belongs

to.

Your phone connects with the device and

sends the datebook event.

On your phone, all group calls you make are

hub calls. Group calls you receive are hub calls

or Talkgroup calls to Talkgroups in the hub you

have joined.

advanced features

Note: These features may not be offered by

SouthernLINC Wireless. For additional

intrinsically safe information, please consult

the FM Supplement manual that is included

with the i365IS.

Your sales representative or your service

provider establishes Talkgroups and hubs for

you. You can choose a name for each when

you create entries for them in Contacts.

group calls, talkgroups, and

hubs

A group call is similar to a private call, but is

made to all members of a Talkgroup at once.

A Talkgroup is a predetermined group of your

join a hub

Press

Enter the hub number using the keypad.

main attractions

Scroll to the hub name in Contacts or

recent calls list.

Find it: M > Select Details.

make group calls

Press

under Join.

Press

#. Enter the hub number using

the keypad.

create a talkgroup hub

Begin creating a new Contacts entry. See

“store a phone number or LINC ID” on

page 18.

Scroll to the hub name in Contacts or

recent calls list.

Assign the hub Contacts type to the entry.

Proceed as if making a InstantLINC

Mobile to Mobile call.

Assign the Talkgroup number as the

number of the hub.

receive group calls

When you receive a group call, the following

appears on the screen:

This creates a hub with the same number as

the Talkgroup it contains. You cannot add any

more Talkgroups to this hub.

•

The name of the hub

view hub details

The name or number of the primary

Talkgroup in the hub

From the recent calls list, scroll to the

hub.

•

The private number of the person

speaking

Press

Select Hub Details

To answer a group call:

main attractions

•

Proceed as if answering a InstantLINC

Mobile to Mobile call. Only one person

at a time may speak on a group call.

Scroll to Off if you want to hear group calls.

Press

Note: Setting Tkgrp Silent to On prevents you

from hearing emergency group calls.

set talkgroup scan

From the main menu, select

emergency group calls

InstantLINC > Scan

Scroll to On

An emergency group call is a hub call

that takes priority over all other phone

activities in the phone making the call and

sounds a special emergency tone in the

phones receiving the call.

Press

To set your phone to receive group calls only

from the primary Talkgroup in a hub:

•

Scroll to Off in step 2.

When you make an emergency group call, a

group call is made using a designated

emergency hub or the hub you currently

belong to.

Find it: M > Call Setup > Scan

turn off group calls

From the main menu, select

A designated emergency hub must be

created for you by SouthernLINC Wireless

and is stored on your SIM card.

InstantLINC > Tkgrp Silent

Scroll to On if you don’t want to hear group

calls.

If no designated emergency hub has been

created for you, emergency group calls you

main attractions

make are made using the hub you currently

belong to. If no designated emergency hub

has been created for you and you have not

joined a hub, you cannot make emergency

group calls.

An emergency group call automatically ends if

there is no activity for 30 seconds.

Emergency group calls you make or receive

do not appear in the recent calls list.

receive an emergency group call

make an emergency group call

When receiving an emergency group call,

your phone sounds a special emergency tone,

unless your phone is set to make no sounds.

Caution: Making an emergency group call

ends all other activity on your phone,

including 911 emergency calls.

To answer an emergency group call:

To make an emergency group call:

•

Proceed as if answering a InstantLINC

Mobile to Mobile call.

Press and hold

the emergency group call.

(

for 3 seconds to start

isolated operation

Press and hold the PTT button on the side

of your phone to talk. Begin talking after

your phone emits a chirping sound.

Isolated Operation lets you continue to make

and receive group calls on the hub you last

used, within a limited coverage area, even if

you lose network coverage.

Release the PTT button to listen.

To end an emergency group call:

Press and hold for 3 seconds.

When you lose network coverage during a

phone call, InstantLINC Mobile to Mobile call,

group call, or data transfer, the call or data

•

(

main attractions

transfer ends. But you can make and receive

new group calls on the hub you last used.

call alert status messages

You can send call alerts that include text

messages up to 10 characters long. These

messages are stored on your SIM card when

your receive your phone. There are 10 you can

choose from.

If the One Touch PTT settings on your phone

would prevent you from making group calls on

the hub you last used, these setting are

overridden while your phone is in Isolated

Operation.

If the phone you send the call alert to has this

capability, the text message appears on that

phone when the call alert is received. If the

phone you send the call alert to does not have

this capability, the call alert appears without

the text message.

Caution: You cannot make emergency group

calls in Isolated Operation, even if the hub you

last used is the designated emergency hub.

You must have network coverage to make

emergency group calls.

If the designated emergency hub is the hub

you last used when you lost network

coverage, your phone treats the hub you used

before the designated emergency hub as the

hub you last used.

send a call alert status message

Proceed as you would when sending any

call alert.

When the Ready to Alert screen appears,

choose the text message you want to

send:

main attractions

Scroll left or right to display the message

you want to send.

Press

under Select to view all messages

and select the one you want to send.

Press the number on you keypad

associated with the message you want to

send. Press 1 and then 0 to choose

message 10.

Press the PTT button until Alert Successful

appears on the display.

receive a call alert status message

When you receive a call alert that includes

a text message, the text message

appears as the part of of the call alert

information when you receive the call alert

and in the recent calls list.

main attractions

basics

See page 1 for a basic phone diagram.

Soft key labels show the current soft key

functions. For soft key locations, see page 1.

display

The home screen shows when you turn on

the phone. To dial a number from the home

screen, press number keys and

status indicators

Status indicators are shown at the top of the

home screen:

1. 2.

Note: Your home screen may look different.

SouthernLINC

10:05 am 4/17

Date and

SouthernLINC

10:05 am 4/17

Time

Contcs

Mesg

Left Soft

Key Label

Right Soft

Key Label

Signal Strength Indicator: Vertical bars

show the strength of the network

Mesg

Contcs

basics

connection. You can’t make or receive

calls when or shows.

Battery Charge Indicator: A fuller battery

indicates a greater charge. Recharge the

battery when your phone shows Low Battery

Active Phone Line: 1 indicates phone line

1 is ready to make calls; 2 indicates phone

line 2 is ready to make calls.

main menu

All your phone’s features can be accessed

through the main menu. You can set the main

Speaker On/Off : Sounds associated with

InstantLINC Mobile to Mobile calls and

Talkgroup calls can be set to come

through the earpiece rather than through

the speaker.

menu to appear as List View or Icon View

Find it: Display/Info Menu View.

Ringer Vibe/Off: Your phone is set to not

ring.

text entry

Some features let you enter text.

Message Indicator: Shows when

you receive a text message.

Your phone provides convenient ways to enter

words, letters, punctuation, and numbers

whenever you are prompted to enter text (for

example, when adding a Contacts entry or

when using Text Messaging).

Packet Data: Your handset is ready to

transfer packet data or is transferring

packet data when it shows a blinking

arrow.

basics

change the character input mode

word method

The Word English text input method lets you

enter text into your phone by pressing keys

just once per letter.

When you see a screen where you can

enter text, press to change the

character input mode.

Select one of the following options:

The Word English text input method

combines the groups of letters found on each

phone key with a fast-access dictionary of

words, and recognizes what you want to text

as you type. It first offers the most commonly-

used word for the key sequence you enter

and lets you access other choices with one or

entry method

Alpha

Press a key several times for

different characters.

Word

Enter words using a predictive

text entering system that lets

you enter a word with fewer key

presses.

more presses of the

key.

enter a word using “word” character

input method

Symbols

Numeric

Enter symbols.

Enter numbers by pressing the

numbers on the keypad.

Select the Word character input method.

Press the corresponding keys once per

letter to enter a word (for example, to

enter the word Bill, press 2 4 5 5).

Tip: When entering text, press and hold

to change letter capitalization (Abc abc).

ABC

basics

If you make a mistake, press

to erase a single character.

Press and hold under Delete or to

delete an entire entry.

under

twice,

and

three times,

Delete or

three times again.

If you make a mistake, press

Delete to erase a single character. Press and

hold under Delete to erase an entire

entry.

under

To accept a word and insert a space,

press

To accept a word completion (such as

Billion when you entered Bill), press

right.

By default, the first letter of an entry is

capitalized and the following letters are

lowercased. After a character is entered, the

cursor automatically advances to the next

space after two seconds or when you enter a

character on a different key.

If you get a word you don’t want, you can

press the

key to see more word

choices and pick the one you want.

Characters scroll in the following order:

alpha method

To enter characters by tapping the keypad:

characters

Space . 1 ? ! , @ & : ; “ - ( ) ‘ ¿ ¡ %

£ $ ¥

Select the Alpha method.

Press the corresponding keys repeatedly

until the desired letter appears. (For

A B C 2 Á Ã Â À Ç

D E F 3 É Ê È

G H I 4 Í Ì

example, to enter the word Bill, press

basics

handsfree speaker

You can use your phone’s handsfree speaker

to make calls without holding the phone to

your ear.

characters

J K L 5

M N O 6 Ñ Ó Õ Ô Ò

P Q R S 7 ß

During a call, press the speaker key

turn the handsfree speaker On.

)

T U V 8 Ú Ü Û Ù

W X Y Z 9

The handsfree speaker stays on until you

press again.

+ - 0 * / \ [ ] = > < # §

Space

)

Note: The handsfree speaker won’t work

when your phone is connected to a handsfree

car kit or headset.

Back

navigation key

transmitters

Press the navigation key

up, down, left, or right

to scroll to items in the

display. When you scroll

to highlight the desired

Note: Consult airline staff about the use of

the Transmitters Off feature during flight. Turn

off your phone whenever instructed to do so

by airline staff.

item, press

basics

Transmitters Off turns off your phone’s calling

features in situations where wireless phone

use is prohibited, but you can use the phone’s

other non-calling features when Transmitters

is turned Off.

Electronics Association 0183 V3.0 (NMEA-

0183) standard. As such it supports the

following sentences: GGA, GLL, GSA, GSV,

RMC, and VTG.

This handset is not a full NMEA-0183

Find it:

Advanced

Transmitters

Off

compliant device supporting electrical RS-422/

RS-232 connectivity as dictated by the NMEA-

0183 standard. Consequently it's unsuitable

for conventional marine NMEA-0183

equipment use. Its intended use is for normal

"terrestrial" mobile users who want to enable

their USB hosting computing devices such as

a PC, laptop or PDA with the phone's highly-

capable GPS functionality.

use GPS with map

software

Your phone is enabled with a highly-capable

GPS receiver that sends location information

to a USB port on a PC, laptop, or PDA.

Note: No serial port connectivity is provided

by your phone. Applications on the host

device which are expecting to receive the

GPS location information via a serial port must

instead use a Virtual Serial Comm Port.

get connected

Open the phone's bottom

connector and insert a cable into the

phone's bottom connector.

The data sent to the host device is formatted

as prescribed in the National Marine

Insert the other end of the cable into a

vacant USB receptacle of your host

basics

device. A virtual USB Comm Port will be

created on your host device upon

successful enumeration of the phone as a

USB Communications Device Class

device.

Set your phone to start sending NMEA-

0183 formatted location information.

Find it:

GPS

Interface

NMEA OUT On.

Your phone is now actively sending location

NMEA-0183 formatted GPS data to your USB

host device.

Ensure no application in your host device

is using the created COMM port. You may

need to ensure that the created virtual

COMM port settings are set as follows:

To stop your phone from sending location

data:

Find it:

GPS

Interface

NMEA OUT Off.

•

Bits per second: 4800

Data bits: 8

Note: Each time you power your phone Off,

NMEA OUT is automatically set to Off and

you need to manually restart it using the

menu selections above.

Parity: None

Stop bits: 1

Flow control: None

Your USB host device will generally provide

charging power (5V, up to 500mA) to your

phone via the cable therefore no other

charging power to it will normally be required.

However some laptops may require that you

provide external AC/DC power to the laptop in

Start the GPS application on your host

device. Set the GPS application to start

accepting NMEA-0183 formatted data

from the created Virtual COMM port.

basics

order for it to provide full 500mA charging

current capability to the phone.

basics

calls

To make and answer calls, see page 16.

•

short text messages received

pictures sent or received

datebook events received

turn off a call alert

You can press the volume keys to turn off a

call alert before answering the call.

The recent calls list displays up to 20 of the

most recent calls and call alerts.

Press

Recent Calls

recent calls

Scroll through the list.

The recent calls list contains information

associated with calls you have made and

received and call alerts you have received.

store an item to contacts from

recent calls

Phone calls, InstantLINC Mobile to Mobile

calls, My Info, or Contacts entries received

from other phones can be stored to the

Contacts list from the Recent Calls list.

When you send or receive InstantLINC

Mobile to Mobile calls, the recent call list

contains the following items with those calls:

•

contact information received

My Info received

Find it:

Recent Calls.

calls

Scroll to or select the item you want to

store.

caller ID

Note: This feature requires a subscription.

Please contacts your sales representative or

SouthernLINC Wireless at 1-800-406-0151.

Press

Save to store the information

as a new entry in the Contacts list.

Caller ID allows people to identify a caller

before answering the phone by displaying the

number of the incoming call. If you do not

want your number displayed when you make

a call, just follow these easy steps.

If Save is not one or you options, press

Update Contacts. And select the contact you

want to update. Press

Press under Done to save your changes.

To block your phone number from being

displayed for a specific outgoing call:

redial

Press * 6 7

Enter the number you want to call.

Press

To redial your last outgoing call, press and

hold or push the PTT button if it was a

InstantLINC Mobile to Mobile call.

To permanently block your number, call

SouthernLINC Wireless at 1-800-406-0151.

calls

If Unreachable: When your handset is out of

coverage or powered off.

call forward

Call forwarding sends calls to the phone

numbers you specify. You can forward all calls

to one number or forward missed calls to

different numbers depending on the reason

you missed the call. You can forward phone

lines 1 and 2 independently.

voice names

You can place calls by speaking comands to

your phone if you have previously assigned a

voice name to your contacts.

Find it:

Call Forward.

assign voice names to contacs

To forward all calls select All Calls and select

To to enter the phone number you want all

your calls forwarded to.

Press

Contact]

under Contcs and select [New

Assign a name, phone number and select

[Options]

You can specify a forwarding number for

each type of missed call by selecting

Detailed and chosing the following options:

Select Voice Name and follow the prompt to

record the voice name.

Press

under Back and

under Done.

If Busy: When your handset is on a call or

transferring data.

place a call using voice name

Press the speaker key until you are

prompted to say the voice name.

)

If No Answer: When you do not answer on

the first 4 rings.

calls

The handset will automatically place the call.

center. If you are on an active call, you must

end it before making an emergency call.

When you make an emergency call, your

phone’s GPS Enabled feature can help

emergency calls

SouthernLINC Wireless may program one or

more emergency phone numbers that you

can call under any circumstances, even when

your phone is locked or the SIM card is not

inserted.

emergency service personnel find you, if you

are in a location where your phone's GPS

antenna has established a clear view of the

open sky and your local emergency response

center has the equipment to process location

information. Because of the limitations of this

feature, always provide your best knowledge

of your location to the emergency response

center when you make an emergency call.

Note: Emergency numbers vary by country.

Your phone’s preprogrammed emergency

number(s) may not work in all locations, and

sometimes an emergency call cannot be

placed due to network, environmental, or

interference issues.

Note: Emergency calls cannot be placed

while the keypad is locked.

Your phone supports emergency calling.

Emergency phone calls can be made even

when your SIM card is blocked or not in your

phone.

Note: If you have not registered on the

network, emergency calls cannot be placed

while your SIM card is in your phone.

Dial 911 or your local emergency number to

be connected to an emergency response

calls

Press

international calls

Note: This feature requires a subscription.

Please contacts your sales representative or

SouthernLINC Wireless at 1-800-406-0151.

turbo dial

The first nine entries in your contacts are set

for turbo dial. They can be called by pressing

and holding the speed dial number

(1 through 9).

If your phone service includes international

dialing, press and hold 0 to insert your local

international access code (indicated by +).

Then, press the keypad keys to dial the

country code and phone number.

voicemail

Note: To receive voice mail messages, you

must first set up a voice mail account with

SouthernLINC Wireless.

speed dial

Each phone number stored in Contacts is

assigned a Speed Dial number, which you can

use to call that number.

receiving a message

When you receive a voice mail message, New

VoiceMail Message appears on the display.

From the home screen, use the keypad to

enter the Speed Dial number assigned to

the phone number you want to call.

To call the SouthernLINC Wireless voice mail

system and listen to the message:

Press

calls

•

To check voicemail messages:

Press the soft key under Call

To dismiss the message notification:

Press or under Back

If the caller leaves a message, this icon

can talk to anyone on your code and channel

within your range.

Note: Range will vary based on terrain, man-

made structures and atmospheric conditions.

•

LINCaround allows you to use code or private

mode operation, use up to 10 channels and

communicate with standalone LINCaround

radios.

appears on the display, reminding you that

you have a new message.

Note: LINCaround is not compatible with

older Family Radio Services products.

LINCaround

The following features and main menu items

will not be available while in LINCaround

mode:

Note: This is an optional feature. Go to

www.southernlinc.com/downloads or contact

SouthernLINC Wireless at 1-800-406-0151

about its availability for purchase.

•

On-network phone calls

LINCaround allows direct two-way handset-

to-handset communications between two or

more handsets equipped for LINCaround. You

can make and receive LINCaround calls even

when network service is not available. You

On-network InstantLINC Mobile to

Mobile calls

•

Data transmission

Incoming message notification

calls

•

Musical ring tones

Call forwarding

Messages

While in LINCaround, this icon

display, indicating that there is no network

signal and LINCaround is active.

appears on the

Phones used in LINCaround mode should be

a minimum of 6 feet apart to maximize

performance and improve transmission range.

Call Timers

Call alerts

Voice records

exit LINCaround

Find it:

LA Options > Exit LINCaround.

set your phone to LINCaround

The following message displays: Switching to

Network Please Wait. After a few seconds, the

network idle screen appears.

Find it:

LINCaround > Go To LINCaround.

After a few seconds, the LINCaround idle screen

appears. The channel you are set to appears

on the first line of the display, the code you

are set to appears on the second line of the

display and LA Ready appears just above the

softkeys.

channels and codes

Your phone has 10 channels and 15 codes.

Channels are divided into sets of frequencies

that allow you to make and receive

LINCaround calls. Other parties may also be

talking on the same channel.

Note: When switching from the network to

LINCaround, the last channel and code that were

set appear on the LINCaround idle screen.

calls

Codes help minimize interference from

unwanted messages and other disturbances

when you are on the same channel as others.

set a code

From the LINCaround idle screen, press

under Edit

To have a conversation, all parties must be on

the same channel and code. For private

LINCaround calls, the person you are calling

must be in LINCaround and set to the same

channel to receive your call.

Scroll to Code and press

under Edit.

Note: When making a code call, all parties

that are on your code and channel can hear

your conversation.

set a channel

From the LINCaround idle screen, press

under Edit

Scroll to Channel and press

Select a channel number from 1 to 10.

When you are finished, press under

under Edit.

Back to return to the LINCaround idle

screen.

calls

Select a code number from 1 to 15 or one

of the following options:

option

Pvt Only: Allows you to have a private

conversation with another person using

LINCaround. When on a private

LINCaround call, no other parties can hear

your conversation. In order to make a

private LINCaround Call, you must use the

valid 10-digit Personal Telephone Number

(PTN) of the person you are calling. The

person you are calling must be in

option

Receive All: Sets your phone to receive

LINCaround transmissions from any phone

that is set to the same channel, regardless

of the code (1-15). When you receive

transmissions with the code set to Receive

All, the display changes from Receive All to the

code on which the transmission was

received.

LINCaround and set to the same channel to

receive your call.

Tip: You can reply to an incoming call within

6 seconds after hearing the short ending

beep by pressing the PTT button.

Note: An error message will occur if you

don’t use a valid PTN, or the person that you

are trying to reach is not in LINCaround, or

is set to a different channel or out of range.

Note: You cannot initiate a code call when

the code is set to Receive All. If you push the

PTT button with the code set to Receive All

you will receive an error message.

When you are finished, press

Back to return to the LINCaround idle

under

screen.

calls

Note: An incoming LINCaround call can be

terminated at any time by pressing

make and receive code calls in

LINCaround

To make a code call in LINCaround:

make a private LINCaround call

Push and hold the PTT button. Transmit

appears on the first line of display. Begin

speaking after your phone emits the

LINCaround tone.

Enter the 10-digit PTN of the person you

want to call on your channel, or press

under Contacts and select a contact, or scroll

to a number in the recent calls list.

Release the PTT button to listen.

Push and hold the PTT button. Begin

speaking after your phone emits the

LINCaround tone.

Note: The tone emitted from your phone

when using LINCaround is 4 beeps and

sounds different from the standard tone

heard with on-network InstantLINC

Mobile to Mobile and Talkgroup calls.

Release the PTT button to listen.

The number or name of the person you are

calling will appear in the first line of the

display.

You could receive an error message if

there are no parties on your channel or

code, or if you are out of range.

When you receive a code call using

LINCaround, Receive appears on the first line of

the display.

calls

automatically exit LINCaround mode and

attempt to find a network signal.

receive a private LINCaround

call

Note: If you are out of network coverage your

phone will not be able to make an emergency

911 cellular call until you go back into the

network coverage area.

The number or name of the person who

initiated the call will appear in the first line

of the display.

You can reply within 6 seconds simply by

pushing the PTT button.

You must wait until the phone reconnects to

the network before attempting to make an

emergency 911 cellular call.

end a private LINCaround call

A private LINCaround call will end if there is

no communication for 6 seconds.

setup options

LINCaround setup options are available in the

LA Options screen in both network and

LINCaround modes.

Note: A private LINCaround call may be

interrupted during the 6 second idle time by

another code call.

access setup options in network

make emergency calls while in

LINCaround mode

If you attempt to make an Emergency 911 call

while in LINCaround mode, your phone will

Find it:

access setup options in LINCaround

Find it: LA Options Setup

LINCaround

Setup.

calls

The following options become available:

option

Direct Launch: Launchs your phone directly into

LINCaround when you select LINCaround from

the Main Menu. If Direct Launch is set to On

you will not see LA Options when you select

LINCaround from the main menu. In order to

have access to your setup options, Direct

Launch must be set to Off. Or you can access

setup options while in LINCaround by

pressing

and selecting LA Options.

State Tone: Notifies you periodically with a

tone that you are in LINCaround mode. You can

select a time frame during which you want

to be notified that you are in LINCaround mode.

Select from 30 minutes

or 4 hours.

calls

customize

making a sound; Silent sets your phone to

neither vibrate nor make a sound.

ring tones

To set the ring tone your phone makes when

you receive phone calls, call alerts, message

notifications, pictures sent using InstantLINC

Mobile to Mobile calls, or datebook

reminders:

Tip: Highlighting a ring tone lets you hear

it.

Select the features you want to assign the

ring tone to.

When you are finished, press

under

Note: Only ring tones stored in your phone’s

memory are available in the ring tones list.

Not all audio files can be assigned as ring

tones.

Done

Note: This icon

you set your phone to Silent. This icon

appears on the display if you set the phone to

appears on the display if

Find it:

Ring Tones

Vibrate All

Make sure Vibrate All is set to Off

Scroll through the list of ring tones and

select the one you want to assign. Vibrate

sets your phone to vibrate instead of

set your phone to vibrate

You can set your phone to vibrate instead of

making a sound when you receive all phone

customize

calls, InstantLINC Mobile to Mobile calls,

Talkgroup calls, call alerts, messages

notifications, pictures sent using InstantLINC

Mobile to Mobile calls, and datebook

reminders.

Find it:

Ring Tones

Make sure Vibrate All is set to Off

Select Vibrate from the list of ring tones.

Select the features you want to set to

make no sound.

Find it:

Ring Tones

Vibrate All.

When you are finished, press

under

Set this option to On or Locked

Done

Setting this option to On lets you turn Vibrate All

off by pressing the up volume control. Setting

this option to Locked requires you to press and

hold the up volume control to turn Vibrate All off.

The Locked option helps prevent you from

accidentally turning Vibrate All off.

wallpaper

You can also access downloadable wallpapers

from the Wallpaper menu.

Find it:

Display/Info

Wallpaper.

Tip: To set Vibrate All to On or Locked using the

volume controls: Press the volume controls to

turn down the volume as far as possible to set

Vibrate All to On. Continue to hold the down

Select Wallpaper

Scroll through the list of pictures and

press to select the wallpaper of your

choice.

volume control to set Vibrate All to Locked

To set your phone to vibrate instead of making

a sound for some features but not others:

Note: You can set the wallpapers to change

automatically after a certain period of time by

customize

turning on the Auto Cycle feature located in the

You can view or change these options:

Wallpaper menu.

options

If you want more wallpapers, you can

download them into your phone for a fee.

Check the Downloads menu option on your

phone for a catalog of items available for

purchase and download.

Start View: Sets Datebook to start in day view,

week view, or month view when you

access Datebook.

Daily Begin: Sets the beginning of your day.

This is the earliest time of day displayed in

week view, if you have a 12-hour day view.

backlight

Set the amount of time that the display and

java apps. backlights remain on, or turn off the

backlight feature to extend battery life.

Delete After: Sets the amount of time

Datebook waits to delete an event after it

occurs.

Time Shift: Lets you shift the times of all

Datebook events. This is useful if you are

traveling to a different time zone.

Find it:

Settings

Display/Info

Backlight

Alert Timeout: Sets the amount of time a tone

continues to sound when you receive a

Datebook reminder.

datebook

Find it:

Datebook

Setup

Clock: Controls whether the time and date

appear on the home screen; sets time and

date format; sets year.

customize

set your privacy options

Find it: GPS Privacy

hide or show

location information

Select from the following options:

Your phone is equipped with a Location

feature for use in connection with location-

based services that may be available in the

future.

option

Restricted: No Java or similar software

applications may view the location of your

phone. However, location information may

still be available to the phone’s owner, fleet

manager, or account administrator.

The Location feature allows the network to

detect your position. Turning Location off will

hide your location from everyone except 911.

Unrestricted: All applications may view the

location of your phone, without notifying

you.

Note: Turning Location on will allow the

network to detect your position using GPS

technology, making some applications and

services easier to use. Turning Location off

will disable the GPS location function for all

purposes except 911, but will not hide your

general location based on the cell site serving

your call. No application or service may use

your location without your request or

permission. GPS-enhanced 911 is not

available in all areas.

Ask Access: When an application attempts to

view the location of your phone, you will be

prompted to give permission. However,

location information may still be available to

the phone’s owner, fleet manager, or

account administrator.

customize

other features

advanced calling

feature

3-way call

Make or receive a phone call

and press 3 Way. Enter

the second phone number,

press and under Join.

call waiting To accept the second call

and put the active call on

hold press

under Yes.

Tip: For quick ways to enter

the number, press to

see the dialing menu.

To accept the second call

and end the active call press

You cannot make any other

calls after you have joined a

3-way call, even if one party

disconnects.

Your phone rings with the

second call for you to

answer.

any key

answer

To answer phone calls by

pressing any key on the

keypad press

Phone Calls

Any Key Ans

other features

contacts

datebook

feature

edit/delete

contact

entry

Press

a contact and press

Edit. Change the desired

content and press under

under Contcs. Select

create

datebook

events

To create a new datebook

event press >

Datebook

[New Event]

see datebook To see a calendar event

event

Done

press

left or right to see the

day and up or down to

Datebook. Press

set ringer ID Press

under Contcs. Select

a contact and press

Edit

Ringer

see the events.

event

reminder

When an event reminder

Select desired ringer, press

, and under Done

occurs press

Press under Back to close

the reminder.

under View.

other features

GPS

To improve GPS performance:

feature

receive

To view the information

while still in the InstantLINC

Mobile to Mobile call press

datebook

events via

InstantLINC

Mobile to

Mobile calls

•

Stay in the open

Move away from other electrical or

electronic devices

The 5 most recent events

received from a LINC ID are

stored with the that LINC ID

on the recent calls list.

•

Remain stationary

Avoid touching the antenna with your

hands

To store events to the

feature

view

Datebook press

under

Save while viewing the event

To see your approximate

you want to store.

approximate location press

GPS

location

Position. Scroll to view the

entire screen.

To recalculate position press

Rfrsh. This may take several

minutes.

other features

handsfree

feature

set GPS

privacy

options

To set the level of privacy for

your GPS system press

The use of wireless phones while driving may

cause distraction. Discontinue a call if you

can't concentrate on driving. Additionally, the

use of wireless devices and their accessories

may be prohibited or restricted in certain

areas. Always obey the laws and regulations

on the use of these products.

GPS

Privacy.

If your GPS PIN security

feature is enabled, enter

your GPS PIN and select the

privacy option you want.

change GPS Note: When you receive

feature

your phone, your GPS PIN is

0000.

speaker-

phone

To activate the

speakerphone while

driving press and hold

the speakerphone key

To change your GPS PIN

press

Change Passwds

Security

)

GPS PIN

auto

answer

To automatically answer

calls when connected to a

car kit or headset press

Enter the current GPS PIN

and enter the new 4- to 8-

digit GPS PIN. Re-enter the

new 4- to 8-digit GPS PIN to

confirm.

Phone Calls

Auto Ans.

Select the amount of rings

before answering.

other features

personalize

pc applications

feature

language

To set the language of your

other PC

applications applications visit:

For a list of complete PC

menu press

Language

Display/Info

www.motorola.com/support

backlight

To select how long the

time length display screen and keypad

are backlit press

TTY

feature

Display/Info

Backlight.

menu style To display the main menu as

turn On TTY From the home screen

graphic icons or a text-based

feature

press

Phone Calls

list press

Display/

TTY

Use TTY

Info

Menu View.

choose TTY From the home screen

mode press Phone Calls

clock

display

To display the clock on the

home screen press

TTY

Type.

Display

Display/Info

Clock

Select from TTY VCO or HCO.

other features

feature

change the

TTY baud

rate

From the home screen

press

keypad lock To lock the keypad press

Phone Calls

Security

Keypad Lock

TTY

Select 45.45 or 50.00

change TTY While in the TTY call, press

Baud

Lock Now or Auto Lock.

Shortcut: To lock the

keypad press

enable SIM To enable SIM PIN, press

PIN Security SIM PIN

mode

during a call

In Call Setup

TTY

Type.

Select from TTY

VCO or HCO.

change SIM To change the SIM PIN,

PIN press

security

feature

Security

Change Passwds

SIM PIN

phone lock

To lock the phone press

Note: You can make emergency calls on a

Security

Phone Lock

locked phone (see page 56). A locked phone

still rings or vibrates for incoming calls or

messages, but you need to unlock it to

answer.

Lock Now or Auto Lock

other features

Important Safety and

Legal Information

Safety and General Information

Safety Information

This section contains important information on the safe and

•

United States Federal Communications Commission, Code

of Federal Regulations; 47 CFR part 2 sub-part J.

efficient operation of your phone. Read this information

before using your integrated multi-service portable radio.*

American National Standards Institute (ANSI) / Institute of

Electrical and Electronics Engineers (IEEE). C95. 1-1992.

Exposure to Radio Frequency (RF)

Energy

Your phone contains a transmitter and receiver. When it is ON, it

receives and transmits RF energy. When you communicate with

your phone, the system handling your call controls the power level

at which your phone transmits.

Your Motorola phone is designed to comply with local regulatory

requirements in your country concerning exposure of human beings

to RF energy.

Institute of Electrical and Electronics Engineers (IEEE).

C95. 1-2005 Edition.^*

International Commission on Non-Ionizing Radiation

Protection (ICNIRP) 1998.

Ministry of Health (Canada). Safety Code 6. Limits of

Human Exposure to Radio frequency Electromagnetic

Fields in the Frequency Range from 3 kHz to 300 GHz,

1999.

•

Australian Communications Authority Radio

communications (Electromagnetic Radiation - Human

Exposure) Standard 2003.

Portable Radio Product Operation and

EME Exposure

ANATEL, Brazil Regulatory Authority, Resolution 303 (July

2, 2002) "Regulation of the limitation of exposure to

Your Motorola radio product is designed to comply with the

following national and international standards and guidelines

regarding exposure of human beings to radio frequency

electromagnetic energy (EME):

The information provided in this document supersedes

the general safety information in user’s guides

published prior to May 1, 2006

Safety Information

electrical, magnetic, and electromagnetic fields in the

radio frequency range between 9 kHz and 300 GHz."

"Attachment to Resolution 303 from July 2, 2002."

When using your radio product as a traditional

two-way radio, hold the radio product in a

vertical position with the microphone one

to two inches (2.5 to 5 cm) away from the

lips

Operational Precautions

To assure optimal radio product performance and to be sure that

human exposure to RF does not exceed the guidelines set forth in

the relevant standards, always follow these instructions and

precautions:

If you wear a radio product on your body when

transmitting, always place the radio product in a Motorola

approved clip, holder, holster, case or body harness. If you do not

use a body-worn accessory supplied or approved by Motorola and

are not using the radio product in the intended use positions along

side the head in the phone mode or in front of the face in the

two-way radio mode, or if you hang your device from a lanyard

around your neck, keep the device at least 2.5 centimeters (1 inch)

from your body when transmitting.

Phone Operation

When placing or receiving a phone call, hold your radio product as

you would a wireline telephone. Speak directly into the

microphone

Approved Accessories

Two-way radio operation

For a list of approved Motorola accessories call 1-800-453-0920, or

visit our website at www.hellomoto.com.

Your radio product has been designed and tested to comply with

national and international standards and guidelines regarding

human exposure to RF electromagnetic energy, when operated in

the two-way mode (at the face, or at the abdomen when using an

audio accessory) at usage factors of up to 50% talk/50% listen.

RF Energy Interference/Compatibility

Nearly every electronic device is subject to RF energy interference

from external sources if inadequately shielded, designed or

otherwise configured for RF energy compatibility. In some

circumstances your handset may cause interference with other

devices.

Transmit no more than the rated duty factor of 50% of the time. To

transmit (talk), push the PTT button. To receive calls, release the

PTT button. Transmitting 50% of the time or less, is important

because this radio generates measurable RF energy only when

transmitting (in terms of measuring for standards compliance).

Safety Information

your wireless phone with your implantable medical device, consult

your health care provider.

Follow Instructions to Avoid Interference

Problems

Turn OFF your radio product where posted notices instruct you to

Hearing Aids

Some phones may interfere with some hearing aids. In the event of

such interference, you may want to consult your hearing aid

manufacturer or physician to discuss alternatives.

do so.

In an aircraft, turn off your radio product whenever instructed to do

so by airline staff. If your radio product offers an airplane mode or

similar feature, consult airline staff about using it in flight.

Other Medical Devices and Health Care Facilities

Implantable Medical Devices

If you have an implantable medical devices, such as a pacemaker

or defibrillator, consult your physician before using this radio

product.

If you use any other personal medical devices, consult your

physician or the manufacturer or your device to determine if it is

adequately shielded from RF energy. Turn off your radio product

when instructed to do so in hospitals or health care facilities that

may be using equipment that is sensitive to external RF energy.

Persons with implantable medical devices should observe the

following precautions:

Bluetooth

•

ALWAYS keep the phone more than 20 centimeters (8

inches) from the implantable medical device when the

phone is turned ON.

This device supports Bluetooth 2.0 including EDR and A2DP Stereo

profiles. In order for Bluetooth devices to communicate with one

another, they must utilize the same Bluetooth profile. To determine

the profiles supported by other Motorola devices, visit

www.hellomoto.com/bluetooth. For other devices, contact their

respective manufacturer.

•

DO NOT carry the phone in a breast pocket;

Use the ear opposite the implantable medical device to

minimize the potential for interference.

•

Turn OFF the phone immediately if you have any reason to

suspect that the interference is taking place.

Certain Bluetooth features including those listed may not be

supported by all compatible Bluetooth-enabled devices, and/or the

functionality of such features may be limited in certain devices, or

by certain wireless carriers. Contact your wireless carrier about

feature availability and functionality.

Read and follow the directions from the manufacturer of your

implantable medical device. If you have any questions about using

Safety Information

Potentially Explosive Atmospheres

Driving Precautions

Areas with potentially explosive atmospheres are often but not

always posted, and can include fueling areas such as below decks

on boats, fuel or chemical transfer or storage facilities, or areas

where the air contains chemicals or particles, such as grain, dust

or metal powders.

Check the laws and regulations on the use of radio products in the

area where you drive. Always obey them.

When using your radio product while driving, please:

•

Give full attention to driving and to the road. Using a

phone may be distracting. Discontinue a call if you can’t

concentrate on driving.

When you are in such area, turn off your handset, and do not

remove, install, or charge batteries unless it is a radio product type

especially qualified for use in such areas as “Intrinsically Safe” (for

example, Factory Mutual, CSA, or UL approved). In such areas,

sparks can occur and cause an explosion or fire.

•

Use hands free operation, if available.

Pull off the road and park before making or answering a

call if driving conditions so require.

•

Do not place a handset in the airbag deployment area.

Batteries and Chargers

Responsible driving practices can be found in the “Smart Practices

While Driving” section at the end of this guide and/or at the

Motorola Web site: www.motorola.com/callsmart.

Caution: Improper treatment or use of batteries may present

a danger of fire, explosion, leakage, or other hazard. For

more information, see the “Battery Use and Battery Safety”

section in this user’s guide.

Your battery, charger, or portable radio may contain symbols,

defined as follows:

Note: The use of wireless phones while driving may cause

distraction. Discontinue a call if you can’t concentrate on driving.

Additionally, the use of wireless devices and their accessories may

be prohibited or restricted in certain areas. Always obey the laws

and regulations on the use of these products.

Symbol

Definition

032374o

Important safety information

follows.

Operational Warnings

Obey all posted signs when using phones in public areas.

Do not dispose of your battery

or phone in a fire.

032376o

Safety Information

Glass Parts

Symbol

Definition

Some parts of your phone may be made of glass. This glass could

break if the product is dropped on a hard surface or receives a

substantial impact. If glass breaks, do not touch or attempt to

remove. Stop using your phone until the glass is replaced by a

qualified service center.

Your battery or phone may

require recycling in

032375o

accordance with local laws.

Contact your local regulatory

authorities for more

information.

Seizures/Blackouts

Do not throw your battery or

phone in the trash.

Some people may be susceptible to epileptic seizures or blackouts

when exposed to flashing lights, such as when playing video

games. These may occur even if a person has never had a previous

seizure or blackout.

Your phone contains an

internal lithium ion battery.

Li Ion BATT

032378o

If you have experienced seizures or blackouts, or if you have a

family history of such occurrences, please consult with your

physician before playing video games or enabling a flashing-lights

feature (if available) on your phone.

Do not let your battery,

charger, or phone get wet.

Listening at full volume to

music or voice through a

headset may damage your

hearing.

Discontinue use and consult a physician if any of the following

symptoms occur: convulsion, eye or muscle twitching, loss of

awareness, involuntary movements, or disorientation. It is always

a good idea to hold the screen away from your eyes, leave the

lights on in the room, take a 15-minute break every hour, and stop

use if you are very tired.

Choking Hazards

Your portable radio or its accessories may include detachable

parts, which may present a choking hazard to small children. Keep

your device and its accessories away from small children.

Caution About High Volume Usage

Listening at full volume to music or voice through a

headset may damage your hearing.

Safety Information

Repetitive Motion

When you repetitively perform actions such as pressing keys or

entering finger-written characters, you may experience occasional

discomfort in your hands, arms, shoulders, neck, or other parts of

your body. If you continue to have discomfort during or after such

use, stop use and see a physician.

Safety Information

Service & Repairs

If you have questions or need assistance, we’re here to help.

Motorola Customer Support Center at 1 (800) 453-0920 (United

States), 1 (877) 483-2840 (TTY, TDD United States for hearing

impaired).

Go to www.motorola.com/support, where you can select from a

number of customer care options. You can also contact the

Export Law Assurances

Service

Repairs

This product is controlled under the export regulations of the

United States of America and Canada. The Governments of the

United States of America and Canada may restrict the exportation

or re-exportation of this product to certain destinations. For further

information contact the U.S. Department of Commerce or the

Canadian Department of Foreign Affairs and International Trade.

Service & Repairs

Specific Absorption Rate Data

SAR Data

ALL MODELS WITH FCC ID IHDP56HJ1 MEET THE

conducted using standard operating positions reviewed by the FCC

with the phone transmitting at its highest certified power level in

all tested frequency bands. Although the SAR is determined at the

highest certified power level, the actual SAR level of the phone

while operating can be well below the maximum value. This is

because the phone is designed to operate at multiple power levels

so as to use only the power required to reach the network. In

general, the closer you are to a wireless base station antenna, the

lower the power output.

GOVERNMENT’S REQUIREMENTS FOR EXPOSURE TO RADIO

WAVES.

Your wireless phone is a radio transmitter and receiver. It is

designed and manufactured not to exceed the emission limits for

exposure to radio frequency (RF) energy set by the Federal

Communications Commission of the U.S. Government. These limits

are part of comprehensive guidelines and establish permitted

levels of RF energy for the general population. The guidelines are

based on standards that were developed by independent scientific

organizations through periodic and thorough evaluation of

scientific studies. The standards include a substantial safety

margin designed to assure the safety of all persons, regardless of

age and health.

Before a phone model is available for sale to the public, it must be

tested and certified to the FCC that is does not exceed the limit

established by the requirement adopted by the government for

safe exposure. The tests are performed in positions and locations

(e.g., at the ear and worn on the body) as required by the FCC for

each model. The highest SAR value for the model i365 (i365IS)

phone when tested for use at the ear is 1.09 W/kg and when

tested on the body, as described in this user guide, is 1.28 W/kg

during packet data transmission. (Measurements for phones worn

on the body differ among models, depending upon available

accessories and FCC requirements.) ^**

The exposure standard for wireless mobile phones employs a unit

of measurement known as the Specific Absorption Rate, or SAR.

The SAR limit set by the FCC is 1.6W/kg.^*Tests for SAR are

In the United States and Canada, the SAR limit for mobile phones used

by the public is 1.6 watts/kg (W/kg) averaged over one gram of tissue.

The standard incorporates a substantial margin of safety to give

additional protection for the public and to account for any variations in

measurements.

** The SAR information includes the Motorola testing protocol, assessment

procedure, and measurement uncertainty range for this product.

SAR Data

While there may be differences between the SAR levels of various

phones and at various positions, they all meet the government

requirement for safe exposure. Please note that improvements to

this product model could cause differences in the SAR value for

later products; in all cases, products are designed to be within the

guidelines.

Additional information on Specific Absorption Rates (SAR) can be

found on the Cellular Telecommunications Industry Association

(CTIA) web-site at http://www.ctia.org or the Canadian Wireless

Telecommunications Association (CWTA) Web site:

http://www.cwta.ca.

SAR Data

Motorola Limited Warranty for the United States and

Canada

Warranty

consumers in the United States or Canada, which are

What Does this Warranty Cover?

accompanied by this written warranty:

Note: FOR IDEN SUBSCRIBER PRODUCTS, ACCESSORIES

AND SOFTWARE PURCHASED IN THE UNITED STATES OR

CANADA

Products Covered

Length of Coverage

Products as defined

above.

One (1) year from the date of

purchase by the first consumer

purchaser of the product.

What Does this Warranty Cover?

Subject to the exclusions contained below, Motorola, Inc. warrants

its Motorola iDEN Digital Mobile and Portable Handsets

("Products"), Motorola-branded or certified accessories sold for

use with these Products ("Accessories") and Motorola software

contained on CD-Roms or other tangible media and sold for use

with these Products ("Software") to be free from defects in

materials and workmanship under normal consumer usage for the

period(s) outlined below. This limited warranty is a

Accessories as

defined above.

One (1) year from the date of

purchase by the first consumer

purchaser of the product.

Products or

The balance of the original

warranty or for ninety (90) days

from the date returned to the

consumer, whichever is longer.

Accessories that are

Repaired or

Replaced.

consumer's exclusive remedy, and applies as follows to

new Products, Accessories and Software purchased by

Warranty

commercial purposes or subjecting the Product or Accessory to

abnormal usage or conditions; or (d) other acts which are not the

fault of Motorola, are excluded from coverage.

Products Covered

Length of Coverage

Software as defined

above. Applies only to

physical defects in the

media that embodies

the copy of the software

(e.g. CD-ROM, or floppy

disk).

Ninety (90) days from the date

of purchase.

Use of Non-Motorola Products and Accessories. Defects or

damage that result from the use of Non-Motorola branded or

certified Products, Accessories, Software or other peripheral

equipment are excluded from coverage.

Unauthorized Service or Modification. Defects or damages

resulting from service, testing, adjustment, installation,

maintenance, alteration, including without limitation, software

changes, or modification in any way by someone other than

Motorola, or its authorized service centers, are excluded from

coverage.

What is not covered? (Exclusions)

Normal Wear and Tear. Periodic maintenance, repair and

replacement of parts due to normal wear and tear are excluded

from coverage.

Altered Products. Products or Accessories with (a) serial

numbers or date tags that have been removed, altered or

obliterated; (b) broken seals or that show evidence of tampering;

non-Motorola housings, antennas, or parts, are excluded from

coverage.

Ornamental Decorations. Ornamental decorations such as

emblems, graphics, rhinestones, jewels, gemstones and their

settings, and other decorative elements, are excluded from

coverage.

Batteries. Only batteries whose fully charged capacity falls below

80% of their rated capacity and batteries that leak are covered by

this limited warranty.

Communication Services. Defects, damages, or the failure of

Products, Accessories or Software due to any communication

service or signal you may subscribe to or use with the Products,

Accessories or Software is excluded from coverage.

Abuse & Misuse. Defects or damage that result from: (a)

improper operation, storage, misuse or abuse, accident or neglect,

such as physical damage (cracks, scratches, etc.) to the surface of

the product resulting from misuse; (b) contact with liquid, water,

rain, extreme humidity or heavy perspiration, sand, dirt or the like,

extreme heat, or food; (c) use of the Products or Accessories for

Software Embodied in Physical Media. No warranty is made

that the software will meet your requirements or will work in

combination with any hardware or software applications provided

by third parties, that the operation of the software products will be

Warranty

uninterrupted or error free, or that all defects in the software

products will be corrected.

purchase; (b) a written description of the problem; (c) the name of

your service provider, if applicable; (d) the name and location of the

installation facility (if applicable) and, most importantly; (e) your

address and telephone number.

Software NOT Embodied in Physical Media. Software that is

not embodied in physical media (e.g. software that is downloaded

from the internet), is provided "as is" and without warranty.

What Other Limitations Are There? ANY IMPLIED

WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, SHALL BE LIMITED TO THE DURATION OF

THIS LIMITED WARRANTY, OTHERWISE THE REPAIR,

REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS EXPRESS

LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE

CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OF IMPLIED. IN NO EVENT SHALL

MOTOROLA BE LIABLE, WHETHER IN CONTRACT OR TORT

(INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE

PURCHASE PRICE OF THE PRODUCT, ACCESSORY OR SOFTWARE,

OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR

CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF

REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF

INFORMATION OR DATA, SOFTWARE OR APPLICATIONS OR

OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION

WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS,

ACCESSORIES OR SOFTWARE TO THE FULL EXTENT THESE

DAMAGES MAY BE DISCLAIMED BY LAW.

Who is covered? This warranty extends only to the first

consumer purchaser, and is not transferable.

What will Motorola Do? Motorola, at its option, will at no

charge repair, replace or refund the purchase price of any Products,

Accessories or Software that does not conform to this warranty.

We may use functionally equivalent

reconditioned/refurbished/pre-owned or new Products,

Accessories or parts. No data, software or applications added to

your Product, Accessory or Software, including but not limited to

personal contacts, games and ringer tones, will be reinstalled. To

avoid losing such data, software and applications please create a

back up prior to requesting service.

How to Obtain Warranty Service or Other Information? To

obtain service or information, please call:

Motorola iDEN Customer Services 1-800-453-0920 or

954-723-4910 or TTY-877-483-2840.

Or visit us online at http://www.motorola.com/iden/support

You will receive instructions on how to ship the Products,

Accessories or Software, at your expense, to a Motorola

Authorized Repair Center. To obtain service, you must include: (a) a

copy of your receipt, bill of sale or other comparable proof of

Some states and jurisdictions do not allow the limitation or

exclusion of incidental or consequential damages, or limitation on

the length of an implied warranty, so the above limitations or

exclusions may not apply to you. This warranty gives you specific

Warranty

legal rights, and you may also have other rights that vary from

state to state or from one jurisdiction to another.

c.Should the Product or parts become, or in MOTOROLA'S opinion

be likely to become, the subject of a claim of infringement of a

United States patent, that such purchaser will permit MOTOROLA,

at its option and expense, either to procure for such purchaser the

right to continue using the Product or parts or to replace or modify

the same so that it becomes non-infringing or to grant such

purchaser a credit for the Product or parts as depreciated and

accept its return. The depreciation will be an equal amount per

year over the lifetime of the Product or parts as established by

MOTOROLA.

Laws in the United States and other countries preserve for

Motorola certain exclusive rights for copyrighted Motorola

software such as the exclusive rights to reproduce and distribute

copies of the Motorola software. Motorola software may only be

copied into, used in, and redistributed with, the Products

associated with such Motorola software. No other use, including

without limitation disassembly of such Motorola software or

exercise of the exclusive rights reserved for Motorola, is

permitted.

MOTOROLA will have no liability with respect to any claim of

patent infringement which is based upon the combination of the

Product or parts furnished hereunder with software, apparatus or

devices not furnished by MOTOROLA, nor will MOTOROLA have

any liability for the use of ancillary equipment or software not

furnished by MOTOROLA which is attached to or used in

connection with the Product or any parts thereof.

Patent and Software Provisions

MOTOROLA will defend, at its own expense, any suit brought

against the end user purchaser to the extent that it is based on a

claim that the Product or parts infringe a United States patent, and

Motorola will pay those costs and damages finally awarded

against the end user purchaser in any such suit which are

attributable to any such claim, but such defense and payments are

conditioned on the following:

Laws in the United States and other countries preserve for

MOTOROLA certain exclusive rights for copyrighted MOTOROLA

software, such as the exclusive rights to reproduce in copies and

distribute copies of such MOTOROLA software. MOTOROLA

software may be used in only the Product in which the software

was originally embodied and such software in such Product may

not be replaced, copied, distributed, modified in any way, or used

to produce any derivative thereof. No other use including, without

limitation, alteration, modification, reproduction, distribution, or

reverse engineering of such MOTOROLA software or exercise or

rights in such MOTOROLA software is permitted. No license is

a.That MOTOROLA will be notified promptly in writing by such

purchaser of any notice of such claim;

b.That MOTOROLA will have sole control of the defense of

such suit and all negotiations for its settlement or

compromise; and

Warranty

granted by implication, estoppel or otherwise under MOTOROLA

patent rights or copyrights.

Warranty

Information From the World Health Organization

WHO Information

Present scientific information does not indicate the need for any

special precautions for the use of mobile phones. If you are

concerned, you may want to limit your own or your children’s RF

exposure by limiting the length of calls or by using hands-free

devices to keep mobile phones away from your head and body.

Source: WHO Fact Sheet 193

Further information: http://www.who.int./peh-emf

Product Registration

Registration

Online Product Registration:

http://www.motorola.com/us/productregistration

Product registration is an important step toward enjoying your new

Motorola product. Registration permits us to contact you for

product or software updates and allows you to subscribe to

updates on new products or special promotions. Registration is not

required for warranty coverage.

Please retain your original dated sales receipt, as you may need to

provide it for warranty validation in the future.

Thank you for choosing a Motorola product.

WHO Information

Wireless: The New Recyclable

Recycling

Your wireless phone can be recycled. Recycling your phone

As a phone user, you have an important role in ensuring that this

device is recycled properly. When it comes time to give this phone

up or trade it in for a new one, please remember that the phone,

the charger, and many of its accessories can be recycled. It's easy.

To learn more about CTIA's Recycling Program for Used Wireless

Devices, please visit us at:

reduces the amount of waste disposed in landfills and allows

recycled materials to be incorporated into new products.

The Cellular Telecommunications Industry Association (CTIA) and

its members encourage consumers to recycle their phones and

have taken steps to promote the collection and environmentally

sound recycling of end-of-life devices.

http://recycling.motorola.young-america.com/ index.html

California Perchlorate Label

Perchlorate Label

Some mobile phones use an internal, permanent backup battery on

the printed circuit board that may contain very small amounts of

perchlorate. In such cases, California law requires the following

label:

“Perchlorate Material - special handling may apply. See

www.dtsc.ca.gov/hazardouswaste/perchlorate.”

There is no special handling required by consumer.

Recycling

Patent and Trademark Information

Patent and Trademark

MOTOROLA, the Stylized M Logo and all other trademarks

Software Copyright Notice

indicated as such herein are trademarks of Motorola, Inc. ® Reg.

The Motorola products described in this manual may include

copyrighted Motorola and third party software stored in

semiconductor memories or other media. Laws in the United

States and other countries preserve for Motorola and third party

software providers certain exclusive rights for copyrighted

software, such as the exclusive rights to distribute or reproduce

the copyrighted software. Accordingly, any copyrighted software

contained in the Motorola products may not be modified,

reverse-engineered, distributed, or reproduced in any manner to

the extent allowed by law. Furthermore, the purchase of the

Motorola products shall not be deemed to grant either directly or

by implication, estoppel, or otherwise, any license under the

copyrights, patents, or patent applications of Motorola or any third

party software provider, except for the normal, non-exclusive,

royalty-free license to use that arises by operation of law in the

sale of a product.

Microsoft and Microsoft Internet Explorer are registered

trademarks of Microsoft Corporation.

T9 is a trademark owned by Tegic Communications.

T9^®Text Input Patent and Trademark Information.

This product is covered by U.S. Pat. 5,818,437, U.S. Pat. 5,953,541,

U.S. Pat. 6,011,554 and other patents pending.

Java and all other Java-based marks are trademarks or registered

trademarks of Sun Microsystems, Inc. in the U.S. and other

countries.

All other product names or services mentioned in this manual are

the property of their respective trademark owners.

Patent and Trademark

Privacy and Data Security

Motorola understands that privacy and data security are important

•

Understanding AGPS: In order to comply with

to everyone. Because some features of your phone may affect your

privacy or data security, please follow these recommendations to

enhance protection of your information:

emergency caller location requirements of the FCC, certain

Motorola phones incorporate Assisted Global Positioning

System (AGPS) technology. AGPS technology also can be

used in non-emergency applications to track and monitor a

user’s location, for example, to provide driving directions.

Users who prefer not to permit such tracking and

•

Monitor access: Keep your phone with you and do not

leave it where others may have unmonitored access. Lock

your device’s keypad where this feature is available.

monitoring should avoid using such applications.

•

Keep software up to date: If Motorola or a

software/application vendor releases a patch or software

fix for your phone which updates the device’s security,

install it as soon as possible.

If you have further questions regarding how use of your phone may

impact your privacy or data security, please contact Motorola at

[email protected], or contact your service provider.

•

Erase before recycling: Delete personal information or

data from your phone prior to disposing of it or turning it in

for recycling. For step-by-step instructions on how to

delete all personal information from your device, please

contact your local service provider.

Privacy and Data Security

Smart Practices While Driving

Driving Safety

Drive Safe, Call Smart ^SM

road. If you receive an incoming call at an inconvenient

time, if possible, let your voice mail answer it for you.

Check the laws and regulations on the use of phones and

their accessories in the areas where you drive. Always

obey them. The use of these devices may be prohibited or

restricted in certain areas. Go to www.motorola.com/callsmart

for more information.

Your phone lets you communicate by voice and data, almost

anywhere, anytime, wherever wireless service is available and

safe conditions allow. When driving a car, driving is your first

responsibility. If you choose to use your phone while driving,

remember the following tips:

•

Let the person you are speaking with know you are

driving; if necessary, suspend the call in heavy

traffic or hazardous weather conditions. Rain, sleet,

snow, ice, and even heavy traffic can be hazardous.

Do not take notes or look up phone numbers while

driving. Jotting down a “to do” list or going through your

address book takes attention away from your primary

responsibility, driving safely.

Dial sensibly and assess the traffic; if possible,

place calls when your car is not moving or before

pulling into traffic. If you must make a call while

moving, dial only a few numbers, check the road and your

mirrors, then continue.

•

Get to know your Motorola phone and its features

such as speed dial and redial. If available, these

features help you to place your call without taking your

attention off the road.

•

When available, use a hands-free

device. If possible, add an additional

layer of convenience to your phone with

one of the many Motorola Original

hands-free accessories available today.

•

Do not engage in stressful or emotional

conversations that may be distracting. Make people

you are talking with aware you are driving and suspend

conversations that can divert your attention away from the

road.

•

Position your phone within easy reach. Be able to

access your phone without removing your eyes from the

Use your phone to call for help. Dial 911 or other local

emergency number in the case of fire, traffic accident, or

medical emergencies.**

Driving Safety

•

Use your phone to help others in emergencies. If you

see an auto accident, crime in progress, or other serious

emergency where lives are in danger, call 911 or other

local emergency number, as you would want others to do

for you.*

Call roadside assistance or a special

non-emergency wireless assistance number when

necessary. If you see a broken-down vehicle posing no

serious hazard, a broken traffic signal, a minor traffic

accident where no one appears injured, or a vehicle you

know to be stolen, call roadside assistance or other

special non-emergency wireless number.^*

Wherever wireless phone service is available.

Driving Safety

index

connect 35

center key 49

center select key 10

clock 74

contacts 71

edit/delete 71

set ringer ID 71

send information 36

setting your phone 34

turning on or off 34

bluetooth 34

accessories 10, 73

active phone line 46

advanced calling 70

3-way calls 70

call waiting 70

alert

call

answer 16

any key answer 70

end 16

set 65

turn off 53

datebook 71

create events 71

receive events via

answer a call 16

make 16

Call alerts

status messages 42

call forward 55

caller ID 54

Calls

InstantLINC 72

setup 67

view reminders 71

dial a phone number 16

dialed calls 53

display 45

backlight 74

battery charging 14

battery indicator 46

battery installation 13

Bluetooth

group, see Group calls

Drafts 22

index