MC50 with Windows® Mobile 5.0
User Guide
MC50 with Windows® Mobile 5.0
User Guide
72E-89337-01
Revision A
May 2007
ii
MC50 User Guide
© 2007 by Motorola, Inc. All rights reserved.
No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means,
without permission in writing from Motorola. This includes electronic or mechanical means, such as
photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to
change without notice.
The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on
a licensed basis. Motorola grants to the user a non-transferable and non-exclusive license to use each
software or firmware program delivered hereunder (licensed program). Except as noted below, such license
may not be assigned, sublicensed, or otherwise transferred by the user without prior written consent of
Motorola. No right to copy a licensed program in whole or in part is granted, except as permitted under
copyright law. The user shall not modify, merge, or incorporate any form or portion of a licensed program with
other program material, create a derivative work from a licensed program, or use a licensed program in a
network without written permission from Motorola. The user agrees to maintain Motorola’s copyright notice on
the licensed programs delivered hereunder, and to include the same on any authorized copies it makes, in
whole or in part. The user agrees not to decompile, disassemble, decode, or reverse engineer any licensed
program delivered to the user or any portion thereof.
Motorola reserves the right to make changes to any software or product to improve reliability, function, or
design.
Motorola does not assume any product liability arising out of, or in connection with, the application or use of
any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under any Motorola, Inc.,
intellectual property rights. An implied license only exists for equipment, circuits, and subsystems contained in
Motorola products.
MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered in the US Patent &
Trademark Office. Bluetooth is a registered trademark of Bluetooth SIG. Microsoft, Windows and ActiveSync
are either registered trademarks or trademarks of Microsoft Corporation. All other product or service names
are the property of their respective owners.
Motorola, Inc.
One Motorola Plaza
Holtsville, New York 11742-1300
iii
Revision History
Changes to the original manual are listed below:
Change
Date
5/2007
Description
Rev A
Initial release.
iv
MC50 User Guide
Table of Contents
Chapter 1
MC50 Documentation Set........................................................................................ ix
Service Information........................................................................................................ xii
Parts of the Mobile Computer ....................................................................................... 1-1
Calibrating the Battery ............................................................................................ 1-6
Starting the Mobile Computer ....................................................................................... 1-6
Calibrating the Screen ............................................................................................ 1-7
Checking Battery Status ............................................................................................... 1-7
Attaching the Handstrap ............................................................................................... 1-7
vi
MC50 with Windows Mobile 5.0 User Guide
Special Character Key ............................................................................................ 2-8
LED Indicators .............................................................................................................. 2-12
Beeper Indicator ........................................................................................................... 2-13
Data Capture ................................................................................................................ 2-13
Image Capture ........................................................................................................ 2-18
Resetting the Mobile Computer .................................................................................... 2-18
Performing a Soft Reset .......................................................................................... 2-18
Performing a Hard Reset ........................................................................................ 2-19
Infrared Communication ............................................................................................... 2-19
Receiving Information ............................................................................................. 2-21
Headset ........................................................................................................................ 3-2
Charging the Spare Battery .................................................................................... 3-4
Battery Charging Indicators .................................................................................... 3-5
Four Slot USB Cradle ................................................................................................... 3-5
Charging ................................................................................................................ 3-6
Battery Charging Indicators .................................................................................... 3-6
Charging ................................................................................................................ 3-7
Battery Charging Indicators .................................................................................... 3-7
Four Slot Spare Battery Charger .................................................................................. 3-8
Spare Battery Charging .......................................................................................... 3-8
Battery Charging Indicators .................................................................................... 3-9
Using the MSR ....................................................................................................... 3-10
USB Connection ..................................................................................................... 3-13
Universal Battery Charger (UBC) Adapter .................................................................... 3-13
Table of Contents
vii
Tell Us What You Think...
viii
MC50 with Windows Mobile 5.0 User Guide
About This Guide
Introduction
This User Guide provides information on operating the MC50 series of mobile computers with Microsoft
Windows Mobile 5.0.
MC50 Documentation Set
The end-user documentation for the MC50 is divided into separate guide that discuss information for specific
types of users.
®
•
Microsoft Applications User Guide for Symbol Devices - describes how to use Microsoft developed
applications.
•
•
Symbol Application Guide - describes how to use Symbol developed sample applications.
MC50 Integrator Guide - provides information on how to set up the MC50 product accessories and how
to install software.
•
SMDK Help File - provides API information for writing applications for the MC50.
x
MC50 with Windows Mobile 5.0 User Guide
Configurations
Depending on device configuration, the MC50 includes the following features:
•
•
•
•
•
Operating System: Microsoft Windows Mobile 5.0
Memory Configuration: 64 MB ROM/64 MB RAM
Display: 3.5” QVGA transflective color touchscreen
Keypads: Navigation (PDA-style) or QWERTY
Data Capture: 1-dimensional bar code scanning via linear CMOS, 1-dimensional or 2-dimensional bar
code imaging, or image capture via camera
•
Radio: Wireless LAN (WLAN)
About This Guide
xi
Software Versions
This guide covers various software configurations and references are made to operating system or software
versions for:
•
•
Adaptation Kit Update (AKU) version
Fusion version.
AKU Version
To determine the Adaptation Kit Update (AKU) version:
Tap Start > Settings > System tab > About icon > Version tab.
This tab lists the operating system version and the build number. The last part of the build number represents
the AKU number. For example, Build 15704.3.5.0 indicates that the device is running AKU version 3.5.0.
Fusion Software
To determine the Fusion software version:
Tap Wireless Strength icon > Wireless Status > Versions.
xii
MC50 with Windows Mobile 5.0 User Guide
Chapter Descriptions
Topics covered in this guide are as follows:
•
Chapter 1, Getting Started lists the parts and accessories for the mobile computer and explains how to
install and charge the batteries, replace the strap, and start the mobile computer for the first time.
•
•
•
Chapter 2, Operating the MC50 provides basic instructions for using and navigating the mobile computer.
Chapter 3, Accessories describes the accessories available for the mobile computer.
Chapter 4, Maintenance and Troubleshooting includes instructions on cleaning and storing the mobile
computer, and provides troubleshooting solutions for potential problems during mobile computer
operation.
•
Notational Conventions
The following conventions are used in this document:
•
•
italics are used to highlight specific items in the general text, and to identify chapters and sections in this
and related documents.
bullets (•) indicate:
• action items
• lists of alternatives
• lists of required steps that are not necessarily sequential
•
sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.
NOTE This symbol indicates something of special interest or importance to the reader. Failure to read the note
will not result in physical harm to the reader, equipment or data.
CAUTION This symbol indicates that if this information is ignored, the possiblity of data or material damage may
occur.
WARNING! This symbol indicates that if this information is ignored the possibility that serious personal
injury may occur.
About This Guide
xiii
Related Documents
•
•
•
•
•
•
MC50 Quick Start Guide, p/n 72-67793-xx
MC50 Regulatory Guide, p/n 72-67863-xx
MC50 Integrator Guide, p/n 72E-89351-xx
Microsoft Applications for Windows Mobile and CE 5.0 User Guide, p/n 72E-78456-xx
Symbol Application Guide, p/n 72-65258-xx
Service Information
If you have a problem with your equipment, contact Motorola Enterprise Mobility Support for your region.
Contact information is available at: http://www.symbol.com/customersupport. If you purchased your Enterprise
Mobility business product from a Motorola business partner, contact that business partner for support.
Before contacting, have the model number and serial number at hand. If your problem cannot be solved by
Motorola Enterprise Mobility Support, you may need to return your equipment for servicing and will be given
specific directions.
Motorola is not responsible for any damages incurred during shipment if the approved shipping container is not
used. Shipping the units improperly can possibly void the warranty.
xiv
MC50 with Windows Mobile 5.0 User Guide
Chapter 1
Getting Started
Chapter 1
Chapter 1 Getting Started
Introduction
This chapter lists the parts and accessories for the mobile computer and explains how to install and charge the
batteries, replace the strap, and start the mobile computer for the first time.
Parts of the Mobile Computer
LED 2
Power Button
LED 1
Phone Speaker
Scan Button
Volume Button
Keypad
Touch screen
Connector
Microphone
Handstrap Clip
Reset Button
Battery
Battery Release
Battery Lock Switch
Speaker
Keypad Lock
IrDA Port
Tether Point
Action Button
Scan Button
Scan Window
Secure Digital (SD) Slot
Stylus
Headset Jack
Figure 1-1 Parts of the MC50
1 - 2 MC50 with Windows Mobile 5.0 User Guide
Accessories
Table 1-1 Accessories
Accessory
Description
Standard battery
Spare 3.7V 1560 mAh lithium-ion battery.
Spare 3.7V 3600 mAh lithium-ion battery.
Performs pen functions.
Extended capacity battery
Stylus
Soft case
Protective case for the mobile computer.
Rigid case
Provides added protection for the mobile computer.
Slips around hand for convenient carrying.
Connects to the mobile computer for charging.
Connects to the single slot or four slot cradle to charge the mobile computer.
For audio playback in noisy environments.
Hand strap
AC adapter cable
Power supply
Headset
Single Slot Cradle
Charges the mobile computer and synchronizes the mobile computer with a
host computer through a USB connection.
Four Slot USB Cradle
Charges up to four mobile computers and synchronizes the mobile computers
with a host computer through a USB connection.
Four Slot Ethernet Cradle
Charges up to four mobile computers, synchronizes the mobile computer with a
host computer through an Ethernet connection, and networks the mobile
computer via an Ethernet hub.
Four Slot Battery Charger
Charges up to four spare batteries.
Charges up to four spare batteries.
Universal Battery Charger
(UBC) Adapter
Magnetic Stripe Reader
(MSR)
Snaps on to the mobile computer to add magstripe capabilities.
Cable Adapter Module (CAM) Connects to the mobile computer to accommodate data communication and
power supply attachment.
Communication cable
Connects to the CAM or single slot cradle for data communication between the
mobile computer and a host computer.
Auto charge cable
Used with the CAM to charge the mobile computer using a vehicle’s power port.
Getting Started 1 - 3
Getting Started
In order to start using the mobile computer for the first time:
•
•
•
install the main battery
charge the main battery and backup battery
start the mobile computer.
Installing the Main Battery
Before using the mobile computer, install a lithium-ion battery:
1. Using the stylus, slide the Battery Lock Switch to the left to unlock it. A red dot appears on the switch.
2. Insert the main battery into the back of the mobile computer as shown below.
3. Press the main battery down into the back of the mobile computer until the battery release slides into
place.
Battery
Battery Lock Switch
Battery Release
Figure 1-2 Inserting the Main Battery
NOTE Ensure the battery is positioned correctly. The battery charging contacts should be placed on top of the
charging contacts in the battery compartment.
4. Using the stylus, slide the Battery Lock Switch to the right to lock it.
1 - 4 MC50 with Windows Mobile 5.0 User Guide
Charging the Mobile Computer Battery
Charging the Main Battery and Memory Backup Battery
Before using the mobile computer for the first time, charge the main battery in the mobile computer for 24
hours, using a cradle or by connecting the power supply to the Cable Adapter Module (CAM).
NOTE To ensure the quickest charging time, turn the mobile computer off while charging.
The mobile computer is equipped with a memory backup battery which automatically charges from the
fully-charged lithium-ion battery. This backup battery retains data in memory when the mobile computer’s
battery is removed. When first using the mobile computer, it takes about 24 hours to charge the backup battery
from the main battery.
NOTE Removing the lithium-ion battery before the backup battery is fully charged risks data loss. DO NOT
remove the battery within the first 24 hours of use.
Using the Single Slot Cradle
1. Connect the cradle to a power source. Refer to the MC50 Integrator Guide for more information on setting
up the Single Slot Cradle.
2. Insert the mobile computer into the cradle to begin charging.
Figure 1-3 Charging in the Single Slot Serial Cradle
NOTE The main battery can be charged using the USB connection to a host computer without a power supply.
The mobile computer must be on when charging through the USB connection.
The standard battery fully charges in approximately 3.5 hours and the extended capacity battery fully charges
in approximately seven hours.
Getting Started 1 - 5
Table 1-2 Mobile Computer LED Indicators
LED
Indication
LED 1
Solid Amber
Flashing Amber
Solid Green
Charging main battery.
Error in charging; check cable connections.
Main battery in mobile computer is fully charged.
Table 1-3 Single Slot Cradle Spare Battery Charging LED Indicators
LED
Indication
Off
No spare battery in slot; spare battery not placed correctly or cradle
is not powered.
Solid Amber
Flashing Amber
Solid Green
Spare battery is charging.
Error in charging; check placement of spare battery.
Spare battery is fully charged.
Using the Four Slot Cradle
To charge the mobile computer’s battery using the Four Slot USB or Ethernet Cradle:
1. Connect the cradle to a power source. Refer to the MC50 Integrator Guide for more information on setting
up the Four Slot Cradle.
2. Insert the mobile computer(s) into the cradle to begin charging.
Figure 1-4 Inserting the Mobile Computer(s) into the Four Slot Cradle
1 - 6 MC50 with Windows Mobile 5.0 User Guide
The standard battery fully charges in approximately 3.5 hours and the extended capacity battery fully charges
Using the CAM
To charge the mobile computer’s battery using the CAM:
1. Attach the CAM to the bottom of the mobile computer.
2. Plug the power connector into the power port, and the other end to a power source.
CAM
Power Supply
Figure 1-5 Charging using the CAM
The standard battery fully charges in approximately 3.5 hours and the extended capacity battery fully charges
Calibrating the Battery
The MC50 battery requires periodic calibration to maintain an accurate calibration of the battery's gas gauge.
To calibrate the battery, deplete the battery completely from a full charge condition. Motorola recommends
performing this once a week.
Starting the Mobile Computer
Press the Power button to turn on the mobile computer. If the mobile computer does not power on, perform a
When turning the mobile computer on for the first time, the mobile computer initializes its Flash File system, the
splash screen displays for about a minute followed by the calibration window. Note that the calibration screen
only appears after a cold boot (hard reset).
Getting Started 1 - 7
Calibrating the Screen
To calibrate the screen so the cursor on the touch screen aligns with the tip of the stylus:
1. Remove the stylus from its storage silo on the back of the mobile computer.
2. Tap the Windows Mobile screen.
3. Carefully press and briefly hold the tip of stylus on the center of each target that appears on the screen.
4. Repeat as the target moves around the screen, then tap the screen to continue.
Checking Battery Status
To check whether the main battery or backup battery in the mobile computer is charged, tap Start > Settings >
System tab > Power icon to display the Power window.
To save battery power, set the mobile computer to turn off after a specified number of minutes.
Attaching the Handstrap
The mobile computer has a handstrap which increases comfort when holding the mobile computer for
extended periods of time. To attach the handstrap:
1. Feed the loop through the handstrap tether.
2. Feed the other end of the handstrap through the loop.
3. Pull the handstrap until the loop is secure.
4. Connect the other end of the handstrap to the handstrap clip at the bottom of the mobile computer.
Handstrap Clip
Figure 1-6 Handstrap Installation
1 - 8 MC50 with Windows Mobile 5.0 User Guide
Magnetic Stripe Reader
The snap-on Magnetic Stripe Reader (MSR) allows easy data capture with the swipe of a magnetic stripe card.
The MSR snaps easily on to the bottom of the mobile computer and can be removed when not in use.
Attaching the MSR
To attach the MSR, slide the MSR onto the bottom of the mobile computer, and secure by pressing the arms
into the mobile computer.
Card Reader
Slot
Arm
Figure 1-7 MSR Installation
To remove the MSR, open the arms from the MSR, and pull the MSR from the mobile computer.
Using the MSR
To use the MSR, the mobile computer must have an application installed which accepts magnetic stripe data. A
data acquired by the MSR.
Start the downloaded sample application. Swipe the magnetic stripe card through the reader, ensuring the
magnetic stripe on the card is positioned as shown. Data encoded on the magnetic stripe displays in the mobile
computer window.
Getting Started 1 - 9
Figure 1-8 Swiping a Card
NOTE The card may be swiped in either direction, from left to right, or from right to left. For best results, gently
press down on the card while swiping to ensure contact with the bottom of the reader.
Installing a Secure Digital Card
Use Secure Digital (SD) memory cards to save or back up data.
To install an SD memory card:
1. Power off the mobile computer.
2. Remove the screw securing SD cover and lift the cover out of the slot.
3. If a card is already installed, press the card in to release it, and then remove it.
Figure 1-9 SD Card Installation
4. Ensure that the card is oriented correctly, and slide it into the slot until you feel a click.
NOTE Do not force the card. If you feel resistance, remove the card, check the orientation, and reinsert it.
5. Replace the SD cover and secure with the screw.
1 - 10 MC50 with Windows Mobile 5.0 User Guide
6. See the documentation that came with the card for information on using the card.
Figure 1-10 SD Card Cover Installation
Turning the Radio On and Off
Using the Signal Strength Icon
To turn off the WLAN radio, tap the Signal Strength icon and select Disable Radio. A red X appears across the
icon indicating the radio is disabled (off).
To turn the WLAN radio back on, tap the Signal Strength icon and select Enable Radio. The red X disappears
from the icon indicating the radio is enabled (on).
Using Wireless Manager
The MC50 also includes Wireless Manager, which provides a simple method of enabling, disabling, and
configuring the device’s wireless capabilities.
To open Wireless Manager:
1. Tap the Connectivity icon.
Figure 1-11 Opening Wireless Manager
Getting Started 1 - 11
2. Select Wireless Manager.
Figure 1-12 Wireless Manager Window
3. To enable or disable the wireless connection, tap its blue bar.
To configure settings for a connection:
1. Tap Menu.
Figure 1-13 Wireless Manager Menu
2. Select Wi-Fi Settings.
1 - 12 MC50 with Windows Mobile 5.0 User Guide
Chapter 2
Operating the MC50
Chapter 2
Chapter 2 Operating the MC50
Introduction
This chapter provides basic instructions for using the mobile computer.
Using the Function Buttons
The mobile computer has various buttons for performing certain functions.
Power Button
Reset Button
Battery Release
Battery Lock Switch
Scan
Button
Keypad
Lock
Volume
Action Button
Scan Button
Figure 2-1 Function Buttons
•
Power: Turns the mobile computer on and off. See Starting the Mobile Computer on page 1-6. Press and
hold the Power button to turn the backlight on and off.
•
•
Volume: Press to display the Volume dialog. Press the top or bottom portion of the button to increase or
decrease volume.
®
•
•
Action: Press to open an application or perform a function. See the Microsoft Applications User Guide
for Symbol Devices to set an application to open.
Keypad Lock: The Keypad Lock switch locks the keypad so that keys are not accidently pressed. Note
that when locked, the mobile computer does not respond to keypad input. Move this switch up to lock the
keypad. Move the switch down to free the keypad for use.
•
2 - 2 MC50 with Windows Mobile 5.0 User Guide
•
•
Using the Stylus
The mobile computer has a stylus for selecting items and entering information. The stylus functions as a
mouse.
•
•
Tap: Touch the screen once with the stylus to press option buttons and open menu items.
Tap and Hold: Tap and hold the stylus on an item to see a list of actions available for that item. On the
pop-up menu that appears, tap the action to perform.
•
Drag: Hold the stylus on the screen and drag across the screen to select text and images. Drag in a list
to select multiple items.
Using the Keypad
The mobile computer has two keypad configurations: a navigation configuration and a QWERTY configuration.
NOTE The Keypad Lock switch locks the keypad so that keys are not accidently pressed. Slide the Keypad Lock
switch to the up position to lock the keypad or the down position to unlock the keypad.
The QWERTY keypad is backlit and illuminates when a key is pressed and stays lit for approximately 5
seconds.
Operating the MC50 2 - 3
Navigation Keypad
The navigation keypad contains application keys, navigation keys, and an Enter key. See Table 2-1 for
descriptions of the keypad.
Figure 2-2 Navigation Configuration
Table 2-1 Navigation Keypad Actions
Key
Action
App 1 - App 4
The App keys can be assigned to an application. Refer to the Microsoft
Applications for Windows Mobile and CE 5.0 User Guide for information on
setting key assignments. Defaults are:
App1: Tasks
App2: Calendar
App3: Contacts
App4: Notes
Navigation/Enter Keys
Press the right, left, top, or bottom of the navigation key to move the cursor
on the screen.
Press the center to enter a selection.
2 - 4 MC50 with Windows Mobile 5.0 User Guide
QWERTY Configuration
The QWERTY keypad uses an alphanumeric keypad that produces the 26-character alphabet (A-Z, both
lowercase and uppercase), numbers (0-9), and assorted characters. The keypad is color-coded to indicate
which modifier key to press to produce a particular character or action. The keypad default is alphabetic,
producing lowercase letters.
Figure 2-3 QWERTY Keypad Configuration
Table 2-2 QWERTY Keypad Actions
Key
Action
Blue Key
Use this key to launch applications, control cursor movement, and select items.
•
•
Press the Blue key once to activate this mode followed by another key.
Press the Blue key twice to lock this mode. Press the Blue key a third time to
unlock.
•
Press and hold the Blue key while selecting a sequence of keys.
When the Blue key is pressed, a Blue key icon appears on the display. See Blue Key
.
Orange Key
Use this key to access the secondary layer of characters and actions.
•
•
Press the Orange key once to activate this mode followed by another key.
Press the Orange key twice to lock the mode. Press the Orange key a third
time to unlock.
•
Press and hold the Orange key while entering characters or actions.
When the Orange key is pressed, an Orange key icon appears on the display. See
.
Operating the MC50 2 - 5
Table 2-2 QWERTY Keypad Actions (Continued)
Key
Action
Navigation Keys
Use these keys in conjunction with the Blue key to move the cursor on the display.
The center key functions as an Enter key.
Cursor Up
Cursor Down
Cursor Left
Cursor Right
Enter
Use this key to turn the display backlight on and off.
Backlight/ áü key
Use this key in conjunction with the Orange key for selecting alternate characters
and symbols. See Special Character Key on page 2-8
.
Star
OK
Use this key to display the soft keyboard Star Key option. Refer to the Microsoft
Applications for Windows Mobile and CE 5.0 User Guide for more information.
Use this key in conjunction with the Blue key, as an OK or close button. This function
is user programmable. Refer to the Microsoft Applications for Windows Mobile and
CE 5.0 User Guide for more information.
Start Menu
Use this key in conjunction with the Blue key, to instantly display the Start menu from
any application without tapping the screen. This function is user programmable.
Refer to the Microsoft Applications for Windows Mobile and CE 5.0 User Guide for
more information.
Menu
Use this key in conjunction with the Blue key, to instantly display the Context Menu
from any application without tapping the screen. This function is user programmable.
Refer to the Microsoft Applications for Windows Mobile and CE 5.0 User Guide for
more information.
Messaging
Use this key in conjunction with the Blue key, to instantly display the Messaging
application without tapping the screen. This function is user programmable. Refer to
the Microsoft Applications for Windows Mobile and CE 5.0 User Guide for more
information.
Calendar
Use this key in conjunction with the Blue key, to instantly display the Calendar
application without tapping the screen. This function is user programmable. Refer to
the Microsoft Applications for Windows Mobile and CE 5.0 User Guide for more
information.
2 - 6 MC50 with Windows Mobile 5.0 User Guide
Table 2-2 QWERTY Keypad Actions (Continued)
Key
Action
Contacts
Use this key in conjunction with the Blue key, to instantly display the Contacts
application without tapping the screen. This function is user programmable. Refer to
the Microsoft Applications for Windows Mobile and CE 5.0 User Guide for more
information.
Phonepad
Use this key in conjunction with the Blue key, to display the Phonepad application
without tapping the screen. This function is user programmable. Refer to the
Microsoft Applications for Windows Mobile and CE 5.0 User Guide for more
information.
Shift Key
Use the Shift/Caps key to change the state of the alpha characters from lowercase to
uppercase. Pressing the key twice, locks the state of the characters to uppercase.
When the Shift/Caps key is pressed, a Shift icon appears on the display. See Shift
.
Table 2-3 QWERTY Keypad Input Modes
Key
Q
W
E
Normal
Shift or CAPS + Key
Orange + Key
Blue + Key
q
w
e
r
Q
W
E
R
T
&
$
Start Menu
Menu
@
%
/
Messaging
Calendar
Contacts
Phonepad
R
T
t
Y
y
u
i
Y
U
I
SEND
U
I
1
2
Cursor Up
OK
O
P
o
p
a
s
d
f
O
P
A
S
D
F
3
END
A
S
(
)
D
F
-
:
G
g
G
+
Note: The key functions can be changed by an application. The keypad may not function exactly as described.
Operating the MC50 2 - 7
Table 2-3 QWERTY Keypad Input Modes (Continued)
Key
Normal
Shift or CAPS + Key
Orange + Key
Blue + Key
H
h
j
H
J
-
J
4
Cursor Left
K
k
l
K
L
5
Enter
L
6
Cursor Right
BACKSPACE
backspace
DEL
Shift
Shift
CAPS
Z
z
Z
?
!
X
x
X
C
V
B
N
M
C
c
‘
V
v
“
B
b
=
7
8
9
áü
N
n
M
,
m
Cursor Down
,
Brightness
TAB
Brightness
tab
SPACE
STAR
.
space
STAR keyboard
*
.
0
#
ENTER
Enter
Note: The key functions can be changed by an application. The keypad may not function exactly as described.
NOTE For detailed keypad configurations including ASCII values and VK codes, refer to the MC50 Integrator
Guide.
2 - 8 MC50 with Windows Mobile 5.0 User Guide
Special Character Key
NOTE Special characters are only available on the QWERTY keypad configurations.
To add special characters using the MC50 áü key, type the related character first, then press the Orange + áü
key. Continue holding the Orange key and pressing the áü key until the special character displays. To modify
an existing character, move the cursor to the right of the character then press and hold the Orange key and
pressing the áü key until the special character replaces the original character. Table 2-4 lists the special
characters that can be generated.
Table 2-4 Special Characters
Key
Special Characters
a
A
c
C
d
D
e
E
i
I
l
L
n
N
o
O
p
P
Operating the MC50 2 - 9
Table 2-4 Special Characters (Continued)
Key
Special Characters
r
R
s
S
t
T
u
U
y
Y
z
Z
$
/
“
(
)
+
!
.
*
@
%
,
2 - 10 MC50 with Windows Mobile 5.0 User Guide
Table 2-4 Special Characters (Continued)
Key
Special Characters
#
&
_
‘
?
:
-
Key Mode Icon
After pressing the Blue, Orange or Shift key, the Key Mode icon appears in the command bar indicating the key
state.
Blue Key Icon
The Blue Key icon indicates that the blue key on the keypad was pressed and that the blue highlighted
functions on the keypad are active. Press the Blue Key once to place the keypad momentarily into this state
and select another key. A hollow blue circle appears. Press the Blue Key twice to lock the keypad in this state
and select another key. A solid blue circle appears. Press the Blue Key a third time to unlock the keypad from
this state. The Blue Key icon disappears. Press and hold the Blue Key while selecting a sequence of keys.
Blue Key Shift State
Figure 2-4 Blue Key Icons
Blue Key Locked State
Operating the MC50 2 - 11
Orange Key Icon
The Orange Key icon indicates that the orange key on the keypad was pressed and that the orange highlighted
functions on the keypad are active. Press the Orange Key once to place the keypad momentarily into this state
and select another key. A hollow orange circle appears. Press the Orange Key twice to lock the keypad in this
state and select another key. A solid orange circle appears. Press the Orange Key a third time to unlock the
keypad from this state. The Orange Key icon disappears. Press and hold the Orange Key while entering
characters or actions.
Orange Key Shift State
Figure 2-5 Orange Key Icons
Orange Key Locked State
Shift Key Icon
The Shift Key icon indicates that the shift key on the keypad was pressed. Press the shift key once to place the
keypad momentarily into this state and select another key. A hollow up arrow appears. Press the shift key twice
to lock the keypad in this state and select another key. A solid up arrow appears. Press the shift key a third time
to unlock the keypad from this state. The up arrow icon disappears.
Shift State
Figure 2-6 Shift Key Icons
Caps Lock State
2 - 12 MC50 with Windows Mobile 5.0 User Guide
When a program, such as Word Mobile, is open the icon appears in the command bar. To move the icon
anywhere on the screen drag it to a new location. Double-tap the icon to return it to its default location in the
command bar. To hide the icon, tap the icon and then tap Hide. To un-hide the icon, tap Start > Today. Tap the
icon and then tap Show.
Entering Information Using the QWERTY Keypad
The QWERTY keypad uses an alphanumeric keypad that produces the 26-character alphabet (A-Z, a-z),
numbers (0-9), functions, and assorted characters. The keypad is color-coded to indicate which modifier key
(Blue or Orange) to press to produce a particular character or action. See Using the Keypad on page 2-2 for
keypad functions.
LED Indicators
The mobile computer has two LED indicators. LED 1 indicates status for main battery charging and scanning.
LED 2 is provided for message indication and is programmable. Table describes the LED indications.
LED 1
LED 2
Figure 2-7 MC50 LEDs
Table 2-5 Mobile Computer LED Indicators
LED
Indication
LED 1 - Data Capture
Solid Green
Solid Red
Successful decode/capture.
Laser enabled, scanning/imaging in process.
Not enabled.
Off
LED 1 - Battery Charging
Solid Green
Solid Amber
Flashing Amber
Main battery in mobile computer is fully charged.
Charging main battery.
Error in charging; check cable connections.
Operating the MC50 2 - 13
Table 2-5 Mobile Computer LED Indicators (Continued)
LED
Indication
LED 2
Green
Red
Programmable
Programmable
Beeper Indicator
The beeper on the mobile computer provides an audible indication for the scan status.
Table 2-6 Beeper Indicator
Beeper
Indication
Standard Use
Low/medium/high beep
Short high beep
Power up.
Bar code decoded (if decode beeper enabled).
Transmission error detected; data is ignored.
4 long low beeps
Parameter Menu Scanning
Low/high/Low/high beep
High/low beep
Successful parameter setting.
Correct programming sequence performed.
Incorrect programming sequence or Cancel bar code scanned.
Low/high beep
Data Capture
The MC50 offers three types of data capture options:
•
•
•
Linear scanning
Imaging
Image Capture.
Camera
Imager
Linear Scanner
Figure 2-8 Data Capture Configurations
2 - 14 MC50 with Windows Mobile 5.0 User Guide
Linear Scanning
Mobile computers with an integrated linear scanner have the following features:
•
•
Reading of a variety of bar code symbologies, including the most popular linear, postal, and 1-D code
Intuitive aiming for easy point-and-shoot operation.
Imaging
Mobile computers with an integrated imager have the following features:
•
Omnidirectional reading of a variety of bar code symbologies, including the most popular linear, postal,
list of bar codes.
•
•
The ability to capture and download images to a host for a variety of imaging applications.
Advanced intuitive laser aiming for easy point-and-shoot operation.
Camera
Mobile computers with an integrated camera have the following features:
•
•
The ability to capture and download images to a host for a variety of imaging applications.
The ability to store the resulting images in its memory.
Scanning Considerations
Typically, scanning is a simple matter of aim, scan and decode. However, it is important to consider range to
optimize any scanning performance:
•
Range
Any scanning device decodes well over a particular working range — minimum and maximum distances
from the bar code. This range varies according to bar code density and scanning device optics.
Scanning within range brings quick and constant decodes; scanning too close or too far away prevents
decodes. Move the mobile computer closer and further away to find the right working range for the bar
codes being scanned. However, the situation is complicated by the availability of various integrated
scanning modules. The best way to specify the appropriate working range per bar code density is
through a chart called a decode zone for each scan module. A decode zone simply plots working range
decode zones for the linear and imager scanning.
•
•
Hold the mobile computer farther away for larger symbols.
Move the mobile computer closer for symbols with bars that are close together.
NOTE Scanning procedures depend on the application and mobile computer configuration. An application may
use different scanning procedures from the one listed above.
Operating the MC50 2 - 15
in.
cm
15 38.1
Note: Typical performance at 73.4º F (23º C)
on high quality symbols.
10 25.4
W
i
d
t
h
5
0
5
12.7
0
o
f
MC 50
6 mil
F
i
2.25
1.75
4.5
12.7
7.5 mil
6.25
e
l
d
10 mil
13 mil
7.5
1.25
2.0
2.2
10 25.4
15 38.1
8.5
20 mil
12
55 mil
4.3
24
15
38.1
in.
cm
0
0
5
12.7
10
25.4
20
50.8
25
63.5
Depth of Field
Figure 2-9 Linear Scanner Decode Zone
2 - 16 MC50 with Windows Mobile 5.0 User Guide
Note: Typical performance at 73˚F (23˚C)
on high quality symbols in normal room light.
Vcc = 3.3V
in.
8
cm
W
i
20.3
d
t
h
10.2
0
4
0
4
8
o
f
MC 50
F
i
e
l
10.2
20.3
5 mil
3.5
7.5
6.67 mil PDF417
6.0
3.75
d
7.5 mil
10
2.75
3.25
10 mil PDF417
10.25
13 mil (100% UPC)
16
13.75
2.25
15 mil PDF417
20 mil
*
*
21.5
5
0
10
15
20
25
In.
cm
38.1
12.7
25.4
0
50.8
63.5
Depth of Field
* Minimum distance determined by symbol length and scan angle.
Figure 2-10 Imager Decode Zone
Linear Scanning
1. Ensure that a scan enabled application is loaded on the mobile computer.
2. Aim the scan exit window at the bar code.
Figure 2-11 Linear Scanning
3. Press the scan button.
• Ensure the red scan beam covers the entire bar code. LED 1 lights red to indicate that scanning is in
process. LED 1 lights green and a beep sounds, by default, to indicate the bar code was decoded
successfully.
Operating the MC50 2 - 17
Correct
Incorrect
Figure 2-12 Linear Scanner Aiming Pattern
Imager Scanning
1. Ensure that a scan enabled application is loaded on the mobile computer.
2. Aim the scan exit window at the bar code.
Figure 2-13 Imager Scanning
3. Press the scan button.
4. Place the bar code in any orientation within the aiming pattern. Ensure the entire symbol is within the
rectangular area formed by the brackets in the aiming pattern. The red laser aiming pattern turns on to
assist in aiming. LED 1 lights red to indicate that scanning is in process. LED 1 lights green and a beep
sounds, by default, to indicate the bar code was decoded successfully.
Linear bar code
PDF417 symbol
Symbol
View Finder
(Aiming Pattern)
Correct
Figure 2-14 Imager Aiming Pattern: Bar Code Centered
Incorrect
Figure 2-15 Imager Aiming Pattern: Bar Code Not Centered
Correct
2 - 18 MC50 with Windows Mobile 5.0 User Guide
5. Release the scan button.
NOTE Imager decoding usually occurs instantaneously. The mobile computer repeats the steps required to take
a digital picture (image) of a poor or difficult bar code, as long as the scan button remains pressed.
Image Capture
The MC50 with camera allows image capture.
1. Ensure that an image capture application is loaded on the mobile computer.
2. Aim the camera exit window at the object to capture.
Figure 2-16 Image Capture
3. Press the scan button.
Upon pressing the trigger, the camera attempts to capture images within its field of view. The camera remains
in this mode as long as the trigger is pulled or the image is captured.
Operating the MC50 2 - 19
Resetting the Mobile Computer
There are two reset functions, warm boot and cold boot. A warm boot restarts the mobile computer by closing
all running programs. A cold boot also restarts the mobile computer, and also resets the clock. Data saved in
flash memory or a memory card is not lost.
Perform a warm boot first. If the mobile computer still does not respond, perform a cold boot.
Performing a Warm Boot
Press the reset button on the back of the mobile computer with the stylus.
Reset Button
Figure 2-17 Reset Button
Performing a Cold Boot
Hold down the Power and right scan buttons, then press and release the reset button located below the
battery release on the back of the mobile computer. Release the Power and right scan buttons
Locking the MC50
Use the Device Lock feature to prevent use of the device. Note that when locked, the mobile computer does
not respond to screen or keypad input.
To lock the device, tap the Device unlocked icon. The icon changes to locked.
Figure 2-18 Device Locked/Unlocked Icons
2 - 20 MC50 with Windows Mobile 5.0 User Guide
To unlock the mobile computer and free it for use, tap Unlock.
Figure 2-19 Unlock Device Window
Tap Unlock on the Unlock Device window.
Infrared Communication
Infrared Receive (IR) allows sending and receiving of information, such as contacts, appointments, and files
between two mobile computers.
Sending Information
To send information:
1. Open the application containing the item to send.
2. Locate the item in the list. For example, a contact name in the Contacts application.
NOTE Ensure that the receiving mobile computer is enabled to accept IR beams. See Receiving Information on
3. Align the IR port of the sending mobile computer with the IR port of the receiving mobile computer so that
they are unobstructed and within close range.
4. Tap and hold the item to send until the menu appears.
Figure 2-20 Beaming Contact Information
5. Tap Send Contact > Beam on the menu. A window displays showing the mobile computer searching for a
device.
Operating the MC50 2 - 21
Figure 2-21 Searching for a Device
6. After the file is sent a message appears indicating successful data transfer.
NOTE Items, but not folders, can also be sent from File Explorer. Tap and hold the item, then tap Beam File on
the pop-up menu.
Figure 2-22 Beaming a File from File Explorer
2 - 22 MC50 with Windows Mobile 5.0 User Guide
Receiving Information
To receive information, align the mobile computer’s IR ports so that they are unobstructed and within close
range. When information is sent from the other mobile computer, the mobile computer (if configured) receives
it automatically.
1. In order to receive information automatically, tap Start > Settings > Connection tab > Beam icon. The Beam
window appears.
Figure 2-23 Beam Window
2. Select the Receive all incoming beams check box to receive beams. By default the mobile computer detects
incoming infrared (IR) beams and prompts you to accept them.
Figure 2-24 Receiving Beam Data Acknowledgement
3. To disable detection of beams, deselect the Receive all incoming beams check box.
NOTE If an older mobile computer attempts to send an IR beam, the receiving mobile computer may not be
prompted to accept it. In this case, before the beam is sent from the older mobile computer, tap Receive
an infrared beam at the bottom of the Beam window.
Chapter 3
Chapter 3
Accessories
Chapter 3 Accessories
Introduction
MC50 accessories provide a variety of product support capabilities. Accessories include cradles, Magnetic
Stripe Reader (MSR) and Cable Adapter Module (CAM) snap-ons, four slot spare battery charger, headset,
Multimedia Card (MMC), Secure Device (SD) card, and Universal Battery Charger (UBC) adapter.
Cradles
•
Single Slot USB cradle charges the mobile computer main battery and a spare battery. It also
synchronizes the mobile computer with a host computer through a USB connection.
•
•
Four Slot USB cradle charges the mobile computer main battery. It also synchronizes the mobile
computer with a host computer through a USB connection.
Four Slot Ethernet cradle charges the mobile computer main battery and connects the mobile computer
with an Ethernet network.
Miscellaneous
•
•
•
•
Four Slot Spare Battery Charger charges up to four mobile computer spare batteries.
Headset can be used in noisy environments.
Multimedia Card or Secure Digital (SD) Card provides secondary non-volatile storage.
UBC adapter adapts the UBC for use with MC50 batteries.
Snap-on Modules
•
•
MSR snaps on to the mobile computer and adds magstripe read capabilities.
CAM snaps on to the mobile computer and connects cables to the mobile computer for battery charging
and synchronizing the mobile computer with a host computer through a USB connection.
The CAM uses the cables listed below:
• AC line cord (country-specific) and power supply, charges the mobile computer.
• Auto charge cable, charges the mobile computer using a vehicle’s cigarette lighter.
• USB cable, adds USB communication capabilities.
3 - 2 MC50 with Windows Mobile 5.0 User Guide
Headset
Use the headset to communicate via Voice-Over-IP (VOIP) or for audio playback and telephony applications.
To connect the headset, remove the plug from the headset jack at the top of the mobile computer and insert the
headset connector. Contact a Motorola representative for compatible headsets.
Figure 3-1 Headset Connection
Multi Media Card (MMC) / Secure Device (SD) Card
The MMC/SD card slot provides secondary non-volatile storage. The slot is located at the top of the mobile
A variety of third-party cards can be used in the mobile computer for storage, Bluetooth connection,
Voice-over-IP, and other functions. Refer to the documentation provided with the card for more information,
and follow the manufacturer’s recommendations for use.
NOTE SD cards are inter-operable with MMC cards; both can be used in MC50 mobile computers.
CAUTION Follow proper ESD precautions to avoid damaging the MMC/SD. Proper ESD precautions include, but
are not limited to, working on an ESD mat and ensuring that the operator is properly grounded.
To insert the MMC/SD:
1. Power off the mobile computer.
2. Remove the card cover at the top of the mobile computer by removing the screw and lifting the cover out of
the slot.
3. If a card is already installed, press the card in to release it, then remove it.
4. Insert the new card with the card contacts aligning with the contacts in the MMC/SD housing, until you feel
a click.
Accessories 3 - 3
Figure 3-2 MMC/SD Card Insertion
5. Replace the housing cover and secure with the screw.
Single Slot USB Cradle
This section describes how to use a Single Slot USB cradle with the mobile computer. For USB communication
setup procedures refer to the MC50 Integrator Guide.
The Single Slot USB Cradle:
•
•
Provides 5.4 VDC power for operating the mobile computer.
Synchronizes information between the mobile computer and a host computer. (With customized or third
party software, it can also synchronize the mobile computer with corporate databases.) Refer to the
MC50 Integrator Guide for information on setting up a partnership between the mobile computer and a
host computer.
•
•
Charges the mobile computer’s battery.
Charges a spare battery.
NOTE Use only a Motorola-approved power supply (p/n 50-14000-147) output rated 5.4 VDC and minimum 3A.
The power supply is certified to EN60950 with SELV outputs. Use of alternative power supply will
invalidate any approval given to this device and may be dangerous.
HINWEIS Benutzen Sie nur eine von Motorola genehmigte Stromversorgung (Teilenr. 50-14000-147) mit einer
Ausgangsleistung von 5.4 V (Gleichstrom) und mindestens 3A. Die Stromversorgung ist nach EN60950
für die Verwendung in SELV-Stromkreisen zertifiziert. Bei Verwendung eines anderen Netzteils werden
alle für das Gerät gewährten Genehmigungen außer Kraft gesetzt, und der Betrieb kann gefährlich sein.
3 - 4 MC50 with Windows Mobile 5.0 User Guide
Charging the Mobile Computer Battery
Connect the cradle to power, or to the host computer using the USB connection. Insert the mobile computer
into the mobile computer slot to begin charging.
Battery Charging LED
Figure 3-3 Mobile Computer Battery Charging
Charging the Spare Battery
Spare Battery
Spare Battery
Charging LED
Spare Battery
Charging Well
Figure 3-4 Spare Battery Charging
Accessories 3 - 5
Battery Charging Indicators
The Single Slot USB Cradle charges the mobile computer’s main battery and a spare battery simultaneously.
The mobile computer’s charge LED indicates the status of the battery charging in the mobile computer. See
The spare battery charging LED on the cradle indicates the status of the spare battery charging in the cradle.
The standard battery fully charges in approximately 3.5 hours and the extended capacity battery fully charges
in approximately seven hours.
Table 3-1 Spare Battery LED Charging Indicators
Spare Battery LED
Indication
(on cradle)
Off
No spare battery in slot; spare battery not placed correctly; cradle is not
powered.
Solid Amber
Flashing Amber
Solid Green
Spare battery is charging.
Error in charging; check placement of spare battery.
Spare battery is fully charged.
Four Slot USB Cradle
This section describes how to use a Four Slot USB cradle with the mobile computer. For cradle communication
setup procedures refer to the MC50 Integrator Guide.
The Four Slot USB cradle:
•
•
Provides 12 VDC power for operating the mobile computer.
Enables data communication between the mobile computer (up to four) and a host computer, using a
USB connection.
•
•
Synchronizes information between the mobile computer and a host computer. (With customized or third
party software, it can also synchronize the mobile computer with corporate databases.)
Simultaneously charges up to four batteries in the mobile computer.
NOTE Use only a Motorola-approved power supply (p/n 50-14000-148) output rated 12 VDC and minimum
3.33A. The power supply is certified to EN60950 with SELV outputs. Use of alternative power supply will
invalidate any approval given to this device and may be dangerous.
HINWEIS Benutzen Sie nur eine von Motorola genehmigte Stromversorgung (Teilenr. 50-14000-148) mit einer
Ausgangsleistung von 12 V (Gleichstrom) und mindestens 3.33A. Die Stromversorgung ist nach
EN60950 für die Verwendung in SELV-Stromkreisen zertifiziert. Bei Verwendung eines anderen
Netzteils werden alle für das Gerät gewährten Genehmigungen außer Kraft gesetzt, und der Betrieb
kann gefährlich sein.
3 - 6 MC50 with Windows Mobile 5.0 User Guide
Charging
Insert the mobile computer into a slot to begin charging.
Figure 3-5 Mobile Computer Battery Charging
Battery Charging Indicators
The mobile computer’s charge LED shows the status of the battery charging in the mobile computer. See Table
1-2 on page 1-5 for charging status indications.
The standard battery fully charges in approximately 3.5 hours and the extended capacity battery fully charges
in approximately seven hours.
Four Slot Ethernet Cradle
This section describes how to set up and use a Four Slot Ethernet cradle with the mobile computer. For cradle
communication setup procedures refer to the MC50 Integrator Guide.
The Four Slot Ethernet cradle:
•
•
Provides 12 VDC power for operating the mobile computer.
Enables data communication between the mobile computer (up to four) and a host computer, using an
Ethernet connection.
•
Synchronizes information between the mobile computer and a host computer. (With customized or third
party software, it can also synchronize the mobile computer with corporate databases.)
•
•
Connects the mobile computer (up to four) to an Ethernet network.
Simultaneously charges up to four batteries in the mobile computer.
Accessories 3 - 7
NOTE Use only a Motorola-approved power supply (p/n 50-14000-148) output rated 12 VDC and minimum
3.33A. The power supply is certified to EN60950 with SELV outputs. Use of alternative power supply will
invalidate any approval given to this device and may be dangerous.
HINWEIS Benutzen Sie nur eine von Motorola genehmigte Stromversorgung (Teilenr. 50-14000-148) mit einer
Ausgangsleistung von 12 V (Gleichstrom) und mindestens 3.33A. Die Stromversorgung ist nach
EN60950 für die Verwendung in SELV-Stromkreisen zertifiziert. Bei Verwendung eines anderen
Netzteils werden alle für das Gerät gewährten Genehmigungen außer Kraft gesetzt, und der Betrieb
kann gefährlich sein.
Charging
Insert the mobile computer into a slot to begin charging.
Figure 3-6 Mobile Computer Battery Charging
Battery Charging Indicators
The mobile computer’s charge LED shows the status of the battery charging in the mobile computer. See Table
1-2 on page 1-5 for charging status indications.
The standard battery fully charges in approximately 3.5 hours and the extended capacity battery fully charges
in approximately seven hours.
3 - 8 MC50 with Windows Mobile 5.0 User Guide
Four Slot Spare Battery Charger
This section describes how to use the Four Slot Spare Battery Charger to charge up to four MC50 spare
batteries.
NOTE Use only a Motorola-approved power supply (p/n 50-14000-148) output rated 12 VDC and minimum
3.33A. The power supply is certified to EN60950 with SELV outputs. Use of alternative power supply will
invalidate any approval given to this device and may be dangerous.
HINWEIS Benutzen Sie nur eine von Motorola genehmigte Stromversorgung (Teilenr. 50-14000-148) mit einer
Ausgangsleistung von 12 V (Gleichstrom) und mindestens 3.33A. Die Stromversorgung ist nach
EN60950 für die Verwendung in SELV-Stromkreisen zertifiziert. Bei Verwendung eines anderen
Netzteils werden alle für das Gerät gewährten Genehmigungen außer Kraft gesetzt, und der Betrieb
kann gefährlich sein.
Spare Battery Charging
1. Connect the charger to a power source.
2. Insert the spare battery into a spare battery charging well and gently press down on the battery to ensure
proper contact.
Spare Battery
Spare Battery
Charging LEDs (4)
Figure 3-7 Four Slot Spare Battery Charger
Accessories 3 - 9
Battery Charging Indicators
An amber LED is provided for each battery charging well. See Table 3-2 for charging status indications. The
standard battery fully charges in approximately 2.5 hours and the extended capacity battery fully charges in
approximately six hours.
Table 3-2 Spare Battery LED Charging Indicators
LED
Indication
Off
No spare battery in slot; spare battery not placed correctly; cradle is not
powered.
Fast Blinking Amber
Slow Blinking Amber
Solid Amber
Error in charging; check placement of spare battery.
Spare battery is charging.
Charging complete.
Magnetic Stripe Reader (MSR)
This section describes how to set up and use the snap-on MSR with the mobile computer. The MSR snaps on
to the bottom of the mobile computer and can be easily removed when not in use.
When attached to the mobile computer, the MSR allows the mobile computer to capture data from magnetic
stripe cards. To download Mobile 5.0 sample applications that include MSR data capture software, visit
Attaching and Removing
To attach, slide the MSR onto the bottom of the mobile computer and secure by snapping the arms into the
mobile computer housing.
Card Reader Slot
Arms
Figure 3-8 MSR Installation
3 - 10 MC50 with Windows Mobile 5.0 User Guide
To remove the MSR open the arms and pull the MSR from the mobile computer.
Using the MSR
The MSR sample application illustrates how an application should handle MSR inputs (refer to the Symbol
Applications User’s Guide).
To use the MSR:
1. Attach the MSR to the mobile computer.
2. Power on the mobile computer.
3. Tap Start > Programs > Samples icon > MSR icon to start the sample application.
4. Swipe the magnetic stripe card through the MSR, with the magnetic stripe on the card facing down. Swipe
the card in either direction, from left to right or from right to left. For best results, gently press down on the
card while swiping to ensure contact with the bottom of the reader.
Figure 3-9 Magnetic Stripe Card Swiping
Cable Adapter Module
This section describes how to and use the snap-on CAM with the mobile computer. The CAM snaps on to the
bottom of the mobile computer and can be easily removed when not in use.
Communications Port
Power Port
Figure 3-10 Cable Adapter Module
Accessories 3 - 11
When attached to the mobile computer, the CAM:
•
•
Provides power for operating the mobile computer, with the appropriate power connection.
Provides USB connection through the USB pass-through port for communication with a USB device,
such as a host computer. For communication setup procedures, refer to the MC50 Integrator Guide.
•
Charges the mobile computer’s battery, when used with the appropriate power supply.
NOTE Use only a Motorola-approved power supply (p/n 50-14000-147) output rated 5.4 VDC and minimum 3A.
The power supply is certified to EN60950 with SELV outputs. Use of alternative power supply will
invalidate any approval given to this device and may be dangerous.
HINWEIS Benutzen Sie nur eine von Motorola genehmigte Stromversorgung (Teilenr. 50-14000-147) mit einer
Ausgangsleistung von 5.4 V (Gleichstrom) und mindestens 3A. Die Stromversorgung ist nach EN60950
für die Verwendung in SELV-Stromkreisen zertifiziert. Bei Verwendung eines anderen Netzteils werden
alle für das Gerät gewährten Genehmigungen außer Kraft gesetzt, und der Betrieb kann gefährlich sein.
Attaching and Removing
To attach, slide the CAM onto the bottom of the mobile computer, until it snaps into place.
Figure 3-11 CAM Installation
To remove the CAM pull the CAM from the mobile computer.
NOTE Remove the CAM from the bottom of the mobile computer before using a cradle for charging and
communication.
3 - 12 MC50 with Windows Mobile 5.0 User Guide
Battery Charging
To charge the mobile computer’s battery through the CAM, attach the CAM to the mobile computer, then
connect the power supply to the CAM. The mobile computer begins charging.
Into Cigarette Lighter
Into Cigarette Lighter
AC Power Supply
Figure 3-12 CAM Power Connection
The mobile computer’s charge LED shows the status of the battery charging in the mobile computer. See Table
1-2 on page 1-5 for charging status indications. The standard battery fully charges in approximately 3.5 hours
and the extended capacity battery fully charges in approximately seven hours.
Accessories 3 - 13
USB Connection
The CAM can connect to and communicate with a USB device, such as a host computer, through its data port.
Refer to the MC50 Integrator Guide for the host computer communication setup procedure.
To connect the CAM to a USB device, connect one end of the data cable to the data port on the CAM and the
other end to the USB port on the device.
Data Port
To Device
USB Port
Figure 3-13 CAM USB Connection
Universal Battery Charger (UBC) Adapter
This section describes how to use the UBC adapter to charge a spare battery.
Use the UBC with a power supply as a standalone spare battery charger, or with the four station UBC2000 to
simultaneously charge up to four spare batteries. For additional information about the UBC2000, see the UBC
2000 Universal Battery Charger Product Guide (p/n 70-33188-xx).
NOTE Use only a Motorola-approved power supply (p/n 50-14000-147) output rated 5.4 VDC and minimum 3A.
The power supply is certified to EN60950 with SELV outputs. Use of alternative power supply will
invalidate any approval given to this device and may be dangerous.
HINWEIS Benutzen Sie nur eine von Motorola genehmigte Stromversorgung (Teilenr. 50-14000-147) mit einer
Ausgangsleistung von 5.4 V (Gleichstrom) und mindestens 3A. Die Stromversorgung ist nach EN60950
für die Verwendung in SELV-Stromkreisen zertifiziert. Bei Verwendung eines anderen Netzteils werden
alle für das Gerät gewährten Genehmigungen außer Kraft gesetzt, und der Betrieb kann gefährlich sein.
3 - 14 MC50 with Windows Mobile 5.0 User Guide
Battery Insertion and Removal
Insert the battery into the battery well with the charging contacts on the battery aligning with the charging pins
on the adapter, and gently press down on the battery to ensure proper contact.
To remove the battery, press the battery release and lift battery out of the well.
Battery
Battery Well
UBC Adapter
POW ER
Battery Release
READY
(Green)
CHARGING or STANDBY or FAULT
(FlashingYellow) (FlashingYellow)
(SolidYellow)
Figure 3-14 UBC Adapter
Battery Charging Indicators
To charge a spare battery using the UBC adapter, insert the spare battery. The spare battery begins charging.
The UBC’s charge LEDs show the status of the battery charging in the adapter. Table 3-3 shows battery
charging status indications. The standard battery fully charges in approximately 2.5 hours and the extended
capacity battery fully charges in approximately six hours.
POW ER
READY
(Green)
CHARGING or STANDBY or FAULT
(FlashingYellow)
(SolidYellow)
(FlashingYellow)
Figure 3-15 UBC Adapter LEDs
Accessories 3 - 15
Table 3-3 UBC Adapter Charge LED Status Indications
LED
POWER
READY
Indication
Description
Red
Power is connected to the UBC Adapter.
Green
Yellow
Charging complete.
Normal charge.
CHARGING
or
Flashing Yellow The battery was deeply discharged and is being trickle charged to bring the
voltage up to the operating level. After operating level voltage is achieved
the battery charges normally.
STANDBY or
FAULT
Flashing Yellow Charging error, check placement of mobile computer/spare battery.
3 - 16 MC50 with Windows Mobile 5.0 User Guide
Chapter 4
Maintenance and Troubleshooting
Chapter 4
Chapter 4 Maintenance and Troubleshooting
Introduction
This chapter includes instructions on cleaning and storing the mobile computer, and provides troubleshooting
solutions for potential problems during mobile computer operation.
Maintaining the MC50
For trouble-free service, observe the following tips when using the mobile computer:
•
Take care not to scratch the screen of the mobile computer. When working with the mobile computer, use
the supplied stylus or plastic-tipped pens intended for use with a touch-sensitive screen. Never use an
actual pen or pencil or other sharp object on the surface of the mobile computer screen. Motorola
recommends the use of a screen protector, part number KT-67525-01.
•
The mobile computer is not water and dust resistant, do not expose it to rain or moisture for an extended
period of time. In general, treat the mobile computer as you would a pocket calculator or other small
electronic instrument.
•
•
The touch-sensitive screen of the mobile computer contains glass. Take care not to drop the mobile
computer or subject it to strong impact.
Protect the mobile computer from temperature extremes. Do not leave it on the dashboard of a car on a
hot day, and keep it away from heat sources.
•
•
Do not store or use the mobile computer in any location that is dusty, damp, or wet.
Use a soft lens cloth to clean the mobile computer. If the surface of the mobile computer screen becomes
soiled, clean it with a soft cloth moistened with a diluted window-cleaning solution.
•
•
Periodically replace the main battery to ensure maximum battery life and product performance. The life
expectancy of the battery is dependant upon individual usage pattern(s).
The MC50 battery requires periodic calibration to maintain an accurate calibration of the battery's gas
gauge. To calibrate the battery, deplete the battery completely from a full charge condition. Motorola
recommends performing this once a week.
4 - 2 MC50 with Windows Mobile 5.0 User Guide
Troubleshooting
Table 4-1 Troubleshooting the Mobile Computer
Problem
Cause
Solution
Mobile computer does Lithium-ion battery
Charge or replace the lithium-ion battery in the mobile computer.
not turn on.
not charged.
Lithium-ion battery
not installed
properly.
Ensure battery is installed properly. See Installing the Main
.
System error.
Perform a soft reset. If the mobile computer still does not turn
on, perform a hard reset. See Resetting the Mobile Computer
.
Rechargeable
Battery failed.
Replace battery. If the mobile computer still does not operate,
lithium-ion battery did
not charge.
try a soft reset, then a hard reset. See Resetting the Mobile
.
Mobile computer
removed from
Insert the mobile computer in cradle and begin charging. The
standard battery requires approximately 3 1/2 hours to recharge
cradle while battery fully and the optional extended capacity battery charges in
was charging.
approximately seven hours.
Cannot see
Mobile computer
Press the Power button.
characters on display. not powered on.
Fail to communicate
with IrDA printer.
Distance from
printer is not
Bring the mobile computer closer to the printer and attempt
communication again.
between 5 inches
and 39 inches.
Obstruction
Check the path to ensure no objects were in the way.
interfered with
communication.
Application is not
Printer support must be included with the application to run IrDA
enabled to run IrDA printing on the mobile computer. See the System Administrator.
printing.
During data
communication, no
Mobile computer
removed from
Replace the mobile computer in the cradle and re-transmit.
data was transmitted, cradle or unplugged
or transmitted data
was incomplete.
from host computer
during
communication.
Incorrect cable
configuration.
See the System Administrator.
No sound.
Volume setting is
low or turned off.
Check the volume slider in the Volume & Sound properties
dialog box in the Control Panel to ensure the volume is not
turned down.
Maintenance and Troubleshooting 4 - 3
Table 4-1 Troubleshooting the Mobile Computer (Continued)
Problem Cause
Solution
Mobile computer turns Mobile computer is
The mobile computer turns off after a period of inactivity. If the
mobile computer is running on battery power, this period can be
set from 30 seconds, one minute, three minutes, five minutes
and 15 minutes. If the mobile computer is running on external
power, this period can be set to one, three, five, 15, and 30
minutes.
itself off.
inactive.
Check the Power dialog box (in the Control Panel), and change
the setting for longer delay before the automatic shutoff feature
activates.
Battery is not
Insert the battery properly. See Installing the Main Battery on
inserted properly.
Battery is depleted. Recharge or replace the battery.
Battery has
exhausted its
usable life.
Replace the battery.
.
Pressing keys or
buttons does not
activate the
Keypad is locked.
Place the keypad lock switch into the unlocked position. See
.
corresponding
feature.
Tapping the window
Screen not aligned
Re-calibrate the screen. Refer to the Microsoft Applications for
buttons or icons does correctly.
not activate the
Windows Mobile and CE 5.0 User Guide, p/n 72E-78456-xx.
The system is not
corresponding
feature.
responding.
A message appears
stating that the mobile stored on the
Too many files
Delete unused memos and records. You can save these records
on the host computer.
computer memory is
full.
mobile computer.
Too many
applications
installed on the
mobile computer.
If you have installed additional applications on the mobile
computer, remove them to recover memory. Select Start >
Settings > Control Panel. Double-tap the Remove Programs
icon. Select the unused program and tap Remove.
Beamed data does
not transmit.
Mobile computers
too close together
or too far apart.
Confirm that the mobile computers are between five inches and
39 inches apart. Also ensure that there is a clear path between
the two devices.
Insufficient room
lighting.
Adjust the room lighting or move to a different location.
4 - 4 MC50 with Windows Mobile 5.0 User Guide
Table 4-1 Troubleshooting the Mobile Computer (Continued)
Problem
Cause
Solution
When receiving
beamed data an out
of memory message
appears.
Not enough free
memory available
for receiving data.
The mobile computer requires at least twice the amount of
memory available as the data you are receiving. For example, to
receive a 30K application, the mobile computer must have at
least 60K free.
The mobile computer
does not accept scan application is not
Scanning
Load a scanning application onto the mobile computer. See
System Administrator.
input.
loaded.
Unreadable bar
code.
Ensure the symbol is not defaced.
Distance between
exit window and bar
code is incorrect.
Ensure the mobile computer is within proper scanning range.
Battery is low.
If the scanner stops emitting a scan beam when you press the
scan button, check the battery level. When the battery is low, the
mobile computer shuts off before the mobile computer notifies
you of the low battery condition.
Note: If the scanner is still not reading symbols, contact the
distributor or Motorola
.
If, after performing these checks, the mobile computer is still not reading symbols, contact the distributor or
Motorola.
Appendix A
Appendix A
Technical Specifications
Technical Specifications
MC50 Technical Specifications
The following tables summarize the mobile computer’s intended operating environment and technical
hardware specifications.
Table A-1 Environmental Specifications
Feature
Operating Temperature
Storage Temperature
Charging Temperature
Humidity
Description
32° to 122° F (0° to 50° C)
-13° to 140° F (-25° to 60° C)
32° to 104° F (0° to 40° C)
5% to 95% non-condensing
Electrostatic Discharge (ESD)
+/- 8 kV air
+/- 4 kV contact
Table A-2 Technical Hardware Specifications
Feature
Description
Dimensions with standard battery:
4.75 in. L x 3.00 in. W x 1.12 in. D
(12.07 cm L x 7.62 cm W x 2.84 cm D)
Navigation Keypad, 1D Scanning
Navigation Keypad, 1D & 2D Imaging
Navigation Keypad, Camera
4.75 in. L x 3.00 in. W x 1.16 in. D
(12.07 cm L x 7.62 cm W x 2.95 cm D)
4.75 in. L x 3.00 in. W x 0.95 in. D
(12.07 cm L x 7.62 cm W x 2.41 cm D)
5.4 in. L x 3.00 in. W x 1.12 in. D
(13.71 cm L x 7.62 cm W x 2.84 cm D)
QWERTY Keypad, 1D Scanning
QWERTY Keypad, 1D & 2D Imaging
5.4 in. L x 3.00 in. W x 1.16 in. D
(13.71 cm L x 7.62 cm W x 2.95 cm D)
A - 2 MC50 with Windows Mobile 5.0 User Guide
Table A-2 Technical Hardware Specifications (Continued)
Feature
Description
5.4 in. L x 3.00 in. W x 0.95 in. D
QWERTY Keypad, Camera
(13.71 cm L x 7.62 cm W x 2.41 cm D)
Dimensions with extended capacity battery:
4.75 in. L x 3.00 in. W x 1.12 in. D
Navigation Keypad, 1D Scanning
(12.07 cm L x 7.62 cm W x 2.84 cm D)
4.75 in. L x 3.00 in. W x 1.16 in. D
(12.07 cm L x 7.62 cm W x 2.95 cm D)
Navigation Keypad, 1D & 2D Imaging
Navigation Keypad, Camera
4.75 in. L x 3.00 in. W x 1.05 in. D
(12.07 cm L x 7.62 cm W x 2.67 cm D)
5.4 in. L x 3.00 in. W x 1.12 in. D
(13.71 cm L x 7.62 cm W x 2.84 cm D)
QWERTY Keypad, 1D Scanning
QWERTY Keypad, 1D & 2D Imaging
QWERTY Keypad, Camera
5.4 in. L x 3.00 in. W x 1.16 in. D
(13.71 cm L x 7.62 cm W x 2.95 cm D)
5.4 in. L x 3.00 in. W x 1.05 in. D
(13.71 cm L x 7.62 cm W x 2.67 cm D)
Weight with standard battery:
Navigation Keypad, 1D Scanning
Navigation Keypad, 1D & 2D Imaging
Navigation Keypad, Camera
QWERTY Keypad, 1D Scanning
QWERTY Keypad, 1D & 2D Imaging
QWERTY Keypad, Camera
6.8 oz (192.8 g)
7.2 oz (204.1 g)
6.9 oz (195.6 g)
7.2 oz (204.1 g)
7.6 oz (215.5 g)
7.3 oz (207.0 g)
Weight with extended capacity battery:
Navigation Keypad, 1D Scanning
Navigation Keypad, 1D & 2D Imaging
Navigation Keypad, Camera
QWERTY Keypad, 1D Scanning
QWERTY Keypad, 1D & 2D Imaging
QWERTY Keypad, Camera
8.3 oz (235.3 g)
8.7 oz (246.6 g)
8.4 oz (238.1 g)
8.7 oz (246.6 g)
9.1 oz (258.0 g)
8.8 oz (249.5 g)
Display
3.5” QVGA transflective color
Resistive touch
Touch Panel
Technical Specifications A - 3
Table A-2 Technical Hardware Specifications (Continued)
Feature
Description
Main Battery
Standard: Rechargeable Lithium-Ion 3.7 V 1560 mAh
Extended Capacity: Rechargeable Lithium-Ion 3.7 V 3600 mAh
Backup Battery
Provides 30 minutes backup at room temperature;
5 minutes at temperature extremes
®
Processor
Intel XScale™ PXA270
®
®
Operating Platform
Microsoft Windows Mobile 5.0
64 MB RAM/ 64 MB ROM
RS-232, USB Client
Memory
Interface
Expansion Slot
SD/MMC user accessible (SDIO)
Options: scanner, camera, memory cards, Bluetooth radio
Keypad Options
Navigation keypad
QWERTY keypad
Optional Scan Engine 1-D Decode
Capability
Code 39, Code 128, Code 93, Codabar, Interleaved 2 of 5,
Discrete 2 of 5, MSI, UPC/EAN family
(EAN-8, EAN-13, EAN-128, UPC-A, UPC-E, UPC/EAN
supplementals)
Optional Imaging 1-D and 2-D Decode
Capability
Code 39, Code 128, Code 93, Codabar, Code 11, Interleaved 2 of
5, Discrete 2 of 5, MSI, UPC/EAN family (EAN-8, EAN-13,
EAN-128, UPC-A, UPC-E, UPC/EAN supplementals), Coupon
Code, Code 39 Trioptic, Composite Code, PDF417, Micro
PDF417, GS1 DataBar Expanded, GS1 DataBar Limited, GS1
DataBar-14, Data Matrix, Maxi Code, QR Code, US Postnet, US
Planet, UK 4-state, Australian 4-state, Canadian 4-state,
Japanese 4-state, Dutch Kix
Optional Scan Engine Scanning
Specifications
Print Contrast: Minimum 35% absolute dark/light reflectance
measured at 675 nm.
Ambient Light Requirements:
Sunlight (max.): 8,000 ft. candles / 86,112 lux
Ambient Light (min.): 0.5 ft. candles / 5 lux (color
temperature: ~5,000K)
Optional Imaging 1-D and 2-D Scanning
Specifications
Ambient Light Requirements (Sunlight): 9,000 ft. candles /
96,900 lux
Printer Support
Zebra: QL320, QL420, Cameo family, Encore 3 and 4 inch
Monarch: 9460
O’Neill: MF2T, MF4T, VMP2000
AIT: PT4000
802.11b (WLAN)
WLAN connectivity
IEEE 802.11b
A - 4 MC50 with Windows Mobile 5.0 User Guide
Table A-2 Technical Hardware Specifications (Continued)
Feature
Description
Antenna
Bluetooth
Security
Internal
Supports commercially available SD Bluetooth cards
LEAP, PEAP, WEP (40/128 bit), WPA-PSK, TKIP, EAP/TLS, FIPS
140-2, CCX
Accessories
Cradles
Single-Slot USB: charging and USB communication
Four-Slot USB: charging and USB communication
Four-Slot Ethernet: charging and Ethernet communication
Chargers
Four-Slot Spare Battery Charger: charges four spare batteries
simultaneously
UBC Adapter: adapts the UBC for use with MC50 spare batteries
Magstripe Reader (MSR)
Adds magstripe reading capabilities.
Magnetic stripe format: ANSI, ISO, AAMVA, CA DMV,
user-configurable generic format
Swipe speed: 5 to 50 in. /127 to 1270 mm/sec, bi-directional
Cable Adapter Module (CAM)
Miscellaneous
Accommodates AC line cord and autocharge cable for charging,
and USB cable for communication
Headset: for use in noisy environments
SDIO Card: provides secondary non-volatile storage
MC50 Accessory Specifications
Table A-3 Single-Slot USB Cradle Technical Specifications
Feature
Description
Dimensions
4.3 in. L x 2.3 in. W x 3.2 in. H (10.92 cm L x 5.84 cm W x 8.13 cm H)
Weight
6.9 oz (196 g)
Power
5.4 V +/- 5%
Interface
USB
Operating Temperature
Storage Temperature
Charging Temperature
32° to 122° F (0° to 50° C)
-40° to 158° F (-40° to 70° C)
32° to 104° F (0° to 40° C)
Technical Specifications A - 5
Table A-3 Single-Slot USB Cradle Technical Specifications (Continued)
Feature Description
Humidity
Drop
5% to 95% non-condensing
30.0 in. (76.2 cm) drops to vinyl tiled concrete at room temperature
Electrostatic Discharge (ESD)
+/- 8 kV air
+/- 4 kV contact
Table A-4 Four-Slot USB Cradle Technical Specifications
Feature
Description
Dimensions
18.0 in. L x 4.0 in. H x 5.0 in. D (45.72 cm H x 10.16 cm W x 12.7 cm D)
Weight
2.38 lb. (1079 g)
Power
12 V
Interface
USB
Operating Temperature
Storage Temperature
Charging Temperature
Humidity
32° to 122° F (0° to 50° C)
-40° to 158° F (-40° to 70° C)
32° to 104° F (0° to 40° C)
5% to 95% non-condensing
30.0 in. (76.2 cm) drops to vinyl tiled concrete at room temperature
Drop
Electrostatic Discharge (ESD)
+/- 8 kV air
+/- 4 kV contact
Table A-5 Four-Slot Ethernet Cradle Technical Specifications
Feature
Description
Dimensions
3.34 in. H x 12.6 in. W x 2.83 in. D (8.48 cm H x 32.00 cm W x 7.19 cm
D)
Weight
2.38 lb. (1079 g)
Power
12 V
Interface
Ethernet
Operating Temperature
Storage Temperature
Charging Temperature
32° to 122° F (0° to 50° C)
-40° to 158° F (-40° to 70° C)
32° to 104° F (0° to 40° C)
A - 6 MC50 with Windows Mobile 5.0 User Guide
Table A-5 Four-Slot Ethernet Cradle Technical Specifications (Continued)
Feature
Description
Humidity
Drop
5% to 95% non-condensing
30.0 in. (76.2 cm) drops to vinyl tiled concrete at room temperature
Electrostatic Discharge (ESD)
+/- 8 kV air
+/- 4 kV contact
Table A-6 Four-Slot Spare Battery Charger Technical Specifications
Feature
Description
Dimensions
8.25 in. L x 6.0 in. W x 1.7 in. H (20.96 cm L x 15.24 cm W x 4.32 cm
H)
Weight
13.6 oz (386 g)
Power
12 V
Operating Temperature
Storage Temperature
Charging Temperature
Humidity
32° to 104° F (0° to 40° C)
-40° to 158° F (-40° to 70° C)
32° to 104° F (0° to 40° C)
5% to 95% non-condensing
30.0 in. (76.2 cm) drops to vinyl tiled concrete at room temperature
Drop
Electrostatic Discharge (ESD)
+/- 8 kV air
+/- 4 kV contact
Table A-7 UBC Adapter Technical Specifications
Feature
Description
Dimensions
6.1 in. L x 2.9 in. W x 2.3 in. H (15.49 cm L x 7.37 cm W x 5.84 cm H)
5.2 oz (147 g)
Weight
Power
5.4 VDC
Operating Temperature
Storage Temperature
Charging Temperature
Humidity
32° to 122° F (0° to 50° C)
-40° to 158° F (-40° to 70° C)
32° to 104° F (0° to 40° C)
5% to 95% non-condensing
Drop
30.0 in. (76.2 cm) drops to vinyl tiled concrete at room temperature
Electrostatic Discharge (ESD)
+/- 8 kV air
+/- 4 kV contact
Technical Specifications A - 7
Table A-8 Magstripe Reader (MSR) Technical Specifications
Feature
Description
Dimensions
Weight
2.3 in. L x 3.14 in. W x 1.1 in. H (5.82 cm L x 7.98 cm W x 2.79 cm H)
1.7 oz (48 g)
Interface
Serial with baud rate up to 19,200
Format
ANSI, ISO, AAMVA, CA DMV, user-configurable generic format
5 to 50 in. (127 to 1270 mm) /sec, bi-directional
Generic, Raw Data
Swipe Speed
Decoders
Mode
Buffered, unbuffered
Track Reading Capabilities
Tracks 1 and 3: 210 bpi
Track 2: 75 and 210 bpi, autodetect
Operating Temperature
Storage Temperature
Humidity
32° to 122° F (0° to 50° C)
-40° to 158° F (-40° to 70° C)
5% to 95% non-condensing
4 ft. (1.22 m) drops to concrete
Drop
Electrostatic Discharge (ESD)
+/- 8 kV air
+/- 4 kV contact
Table A-9 Cable Adapter Module (CAM) Technical Specifications
Feature
Description
Dimensions
Weight
2.4 in. L x 3.2 in. W x 0.97 in. H (6.10 cm L x 8.13 cm W x 2.46 cm H)
1.5 oz (43 g)
Power
5.4 VDC nominal +/- 5%
Interface
Accommodates AC line cord and autocharge cable for charging, and USB
cable for communication
Operating Temperature
Storage Temperature
Humidity
-13° to 122° F (-25° to 50° C)
-40° to 158° F (-40° to 70° C)
5% to 95% non-condensing
A - 8 MC50 with Windows Mobile 5.0 User Guide
Glossary
Chapter 1
GlossaryGlossary
Numeric
802.11/802.11b. A radio protocol that may be used by the Symbol Spectrum24 radio card. Symbol radio cards
that use the 802.11 protocol also have an ESS_ID.
A
Access Point. Access Point (AP) refers to Symbol’s Spectrum24 Ethernet Access Point. It is a piece of
communications equipment that manages communications between the host computer system and one or
more wireless mobile computers. An AP connects to a wired Ethernet LAN and acts as a bridge between
the Ethernet wired network and IEEE 802.11 interoperable radio-equipped mobile units, such as a mobile
computer. The AP allows a mobile user to roam freely through a facility while maintaining a seamless
connection to the wired network.
®
®
AirBEAM Manager. AirBEAM Manager is a comprehensive wireless network management system that
provides essential functions that are required to configure, monitor, upgrade and troubleshoot the
®
Spectrum24 wireless network and its components (including networked mobile computers). Some features
include event notification, access point configuration, diagnostics, statistical reports, auto-discovery,
wireless proxy agents and monitoring of access points and mobile units.
®
AirBEAM Smart Client. AirBEAM® Smart Client is part of Symbol’s AirBEAM® suite, which also includes
AirBEAM® Safe and AirBEAM® Manager. The AirBEAM® Smart Client system uses the network accessible
host server to store software files that are to be downloaded to the mobile computers. The AirBEAM® Smart
Client provides the mobile computers with the “smarts” to request software from the host. It allows them to
request, download and install software, as well as to upload files and status data. The AirBEAM® Smart
Client uses the industry standard FTP or TFTP file transfer protocols to check the host system for updates,
and if necessary, to transfer updated software. Most often, AirBEAM® Smart Client is used with wireless
networks, but any TCP/IP connection can be used. For more information, refer to the AirBEAM® Smart
Windows® CE Client Product Reference Guide (p/n 72-63060-xx).
AP. See Access Point.
Aperture. The opening in an optical system defined by a lens or baffle that establishes the field of view.
API. An interface by means of which one software component communicates with or controls another. Usually
used to refer to services provided by one software component to another, usually via software interrupts or
function calls
Glossary - 2 MC50 with Windows Mobile 5.0 User Guide
Application Programming Interface. See API.
ASCII. American Standard Code for Information Interchange. A 7 bit-plus-parity code representing 128 letters,
numerals, punctuation marks and control characters. It is a standard data transmission code in the U.S.
Autodiscrimination. The ability of an interface controller to determine the code type of a scanned bar code.
After this determination is made, the information content is decoded.
B
Bar. The dark element in a printed bar code symbol.
Bar Code. A pattern of variable-width bars and spaces which represents numeric or alphanumeric data in
machine-readable form. The general format of a bar code symbol consists of a leading margin, start
character, data or message character, check character (if any), stop character, and trailing margin. Within
this framework, each recognizable symbology uses its own unique format. See Symbology.
Bar Code Density. The number of characters represented per unit of measurement (e.g., characters per inch).
Bar Height. The dimension of a bar measured perpendicular to the bar width.
Bar Width. Thickness of a bar measured from the edge closest to the symbol start character to the trailing edge
of the same bar.
Bit. Binary digit. One bit is the basic unit of binary information. Generally, eight consecutive bits compose one
byte of data. The pattern of 0 and 1 values within the byte determines its meaning.
Bits per Second (bps). Bits transmitted or received.
Boot or boot-up. The process a computer goes through when it starts. During boot-up, the computer can run
self-diagnostic tests and configure hardware and software.
bps. See Bits Per Second.
Byte. On an addressable boundary, eight adjacent binary digits (0 and 1) combined in a pattern to represent a
specific character or numeric value. Bits are numbered from the right, 0 through 7, with bit 0 the low-order
bit. One byte in memory is used to store one ASCII character.
C
CDRH. Center for Devices and Radiological Health. A federal agency responsible for regulating laser product
safety. This agency specifies various laser operation classes based on power output during operation.
CDRH Class 1. This is the lowest power CDRH laser classification. This class is considered intrinsically safe,
even if all laser output were directed into the eye's pupil. There are no special operating procedures for this
class.
Glossary - 3
CDRH Class 2. No additional software mechanisms are needed to conform to this limit. Laser operation in this
class poses no danger for unintentional direct human exposure.
Character. A pattern of bars and spaces which either directly represents data or indicates a control function,
such as a number, letter, punctuation mark, or communications control contained in a message.
Character Set. Those characters available for encoding in a particular bar code symbology.
Check Digit. A digit used to verify a correct symbol decode. The scanner inserts the decoded data into an
arithmetic formula and checks that the resulting number matches the encoded check digit. Check digits are
required for UPC but are optional for other symbologies. Using check digits decreases the chance of
substitution errors when a symbol is decoded.
Codabar. A discrete self-checking code with a character set consisting of digits 0 to 9 and six additional
characters: ( - $ : / , +).
Code 128. A high density symbology which allows the controller to encode all 128 ASCII characters without
adding extra symbol elements.
Code 3 of 9 (Code 39). A versatile and widely used alphanumeric bar code symbology with a set of 43
character types, including all uppercase letters, numerals from 0 to 9 and 7 special characters (- . / + % $and
space). The code name is derived from the fact that 3 of 9 elements representing a character are wide, while
the remaining 6 are narrow.
Code 93. An industrial symbology compatible with Code 39 but offering a full character ASCII set and a higher
coding density than Code 39.
Code Length. Number of data characters in a bar code between the start and stop characters, not including
those characters.
Cold Boot. A cold boot restarts the mobile computer and erases all user stored records and entries.
COM port. Communication port; ports are identified by number, e.g., COM1, COM2.
Continuous Code. A bar code or symbol in which all spaces within the symbol are parts of characters. There
are no intercharacter gaps in a continuous code. The absence of gaps allows for greater information density.
Cradle. A cradle is used for charging the mobile computer battery and for communicating with a host computer,
and provides a storage place for the mobile computer when not in use.
D
DCP. See Device Configuration Package.
Dead Zone. An area within a scanner's field of view, in which specular reflection may prevent a successful
decode.
Decode. To recognize a bar code symbology (e.g., UPC/EAN) and then analyze the content of the specific bar
code scanned.
Glossary - 4 MC50 with Windows Mobile 5.0 User Guide
Decode Algorithm. A decoding scheme that converts pulse widths into data representation of the letters or
numbers encoded within a bar code symbol.
Decryption. Decryption is the decoding and unscrambling of received encrypted data. Also see, Encryption
and Key.
Depth of Field. The range between minimum and maximum distances at which a scanner can read a symbol
with a certain minimum element width.
Device Configuration Package. The Symbol Device Configuration Package provides the Product Reference
Guide (PRG), flash partitions, Terminal Configuration Manager (TCM) and the associated TCM scripts. With
this package hex images that represent flash partitions can be created and downloaded to the mobile
computer.
DHCP. (Dynamic Host Configuration Protocol) Software that automatically assigns IP addresses to client
stations logging onto a TCP/IP network. Similar to BOOTP, but also permits the leasing of an IP address. It
eliminates having to manually assign permanent IP addresses. DHCP software typically runs in servers and
is also found in network devices such as routers that allow multiple users access to the Internet.
DHCP Server. A server in the network or a service within a server that assigns IP addresses.
Discrete Code. A bar code or symbol in which the spaces between characters (intercharacter gaps) are not part
of the code.
Discrete 2 of 5. A binary bar code symbology representing each character by a group of five bars, two of which
are wide. The location of wide bars in the group determines which character is encoded; spaces are
insignificant. Only numeric characters (0 to 9) and START/STOP characters may be encoded.
DNS Server. The Control Panel allows you to set the IP address for a DNS Server, if used. This allows users
to use server names, rather than IP addresses. It is set on the Network tab of the Control Panel.
Domain Name. The Control Panel allows you to set a Domain Name for the DNS Server, if used (e.g.,
symbol.com). It is set on the Network tab of the Control Panel.
DOS. Disk Operating System. This is basic software that allows you to load and use software applications on
your computer. Also see NetID.
DRAM. Dynamic random access memory.
E
EAN. European Article Number. This European/International version of the UPC provides its own coding format
and symbology standards. Element dimensions are specified metrically. EAN is used primarily in retail.
Element. Generic term for a bar or space.
Encoded Area. Total linear dimension occupied by all characters of a code pattern, including start/stop
characters and data.
Glossary - 5
Encryption. Encryption is the scrambling and coding of data, typically using mathematical formulas called
algorithms, before information is transmitted over any communications link or network. A key is the specific
code used by the algorithm to encrypt or decrypt the data. Also see, Decryption and Key.
ENQ (RS-232). ENQ software handshaking is also supported for the data sent to the host.
ESD. Electro-Static Discharge
ESN. Electronic Serial Number. The unique hardware number associated with a cellular device, which is
transmitted to the system when the device communicates with the cellular system.
ESS_ID. Extended Service Set Identifier, defines the coverage area. Prior to the release of the 802.11
specification the ESS_ID was called the Net_ID or Network Identifier. For mobile computers using
Spectrum24 radios with the 802.11 protocol, an ESS_ID allows facilities to limit which Access Points a
mobile computer can communicate with. It is set on the Network tab of the Control Panel. The mobile
computer can only communicate with Spectrum24 Access Points that have matching ESS_IDs.
Ethernet. Ethernet communication port. Allows a wired interface to a radio network.
F
File Transfer Protocol (FTP). A TCP/IP application protocol governing file transfer via network or telephone
lines. See TCP/IP.
Flash Disk. An additional megabyte of non-volatile memory for storing application and configuration files.
Flash Memory. Flash memory is responsible for storing the system firmware and is non-volatile. If the system
power is interrupted the data is not be lost.
Frequency Hopping. The use of a random sequence of frequency channels to achieve spread spectrum
compliance. Stations that use frequency hopping change their communications frequency at regular
intervals. A hopping sequence determines the pattern at which frequencies are changed. Messages take
place within a hop. See Hopping Sequence and Spread Spectrum.
FTP. See File Transfer Protocol.
G
Gateway Address. An IP address for a network gateway or router. A mobile computer may be part of a subnet
as specified by its IP address and Netmask. It can send packets directly to any node on the same subnet.
If the destination node is on a different subnet, then the mobile computer sends the packet to the gateway
first. The gateway determines how to route the packet to the destination subnet. This field is an option used
by networks that require gateways.
Glossary - 6 MC50 with Windows Mobile 5.0 User Guide
H
Hard Reset. See Cold Boot.
Hopping Sequence. A set of random frequencies designed to minimize interference with other sets of random
frequencies. A hopping sequence determines the pattern with which a station that uses frequency hopping
changes its communications frequency. See Frequency Hopping.
Host Computer. A computer that serves other computers in a network, providing such services as computation,
database access, supervisory programs and network control.
Hz. Hertz; A unit of frequency equal to one cycle per second.
I
IDE. Intelligent drive electronics. Refers to the solid-state hard drive type.
IEC. International Electrotechnical Commission. This international agency regulates laser safety by specifying
various laser operation classes based on power output during operation.
IEC (825) Class 1. This is the lowest power IEC laser classification. Conformity is ensured through a software
restriction of 120 seconds of laser operation within any 1000 second window and an automatic laser
shutdown if the scanner's oscillating mirror fails.
IEEE Address. See MAC Address.
Imaging Scanning. Mobile computers with an integrated imager use digital camera technology to take a digital
picture of a bar code, store the resulting image in memory and execute state-of-the-art software decoding
algorithms to extract the data from the image.
Input/Output Ports. I/O ports are primarily dedicated to passing information into or out of the mobile
computer’s memory. Series 9000 mobile computers include Serial and USB ports.
Intercharacter Gap. The space between two adjacent bar code characters in a discrete code.
Interleaved 2 of 5. A binary bar code symbology representing character pairs in groups of five bars and five
interleaved spaces. Interleaving provides for greater information density. The location of wide elements
(bar/spaces) within each group determines which characters are encoded. This continuous code type
uses no intercharacter spaces. Only numeric (0 to 9) and START/STOP characters may be encoded.
Interleaved Bar Code. A bar code in which characters are paired together, using bars to represent the first
character and the intervening spaces to represent the second.
Internet Protocol Address. See IP.
IOCTL. Input/Output Control.
I/O Ports. interface The connection between two devices, defined by common physical characteristics, signal
characteristics, and signal meanings. Types of interfaces include RS-232 and PCMCIA.
Glossary - 7
IP. Internet Protocol. The IP part of the TCP/IP communications protocol. IP implements the network layer (layer
3) of the protocol, which contains a network address and is used to route a message to a different network
or subnetwork. IP accepts “packets” from the layer 4 transport protocol (TCP or UDP), adds its own header
to it and delivers a “datagram” to the layer 2 data link protocol. It may also break the packet into fragments
to support the maximum transmission unit (MTU) of the network.
IP Address. (Internet Protocol address) The address of a computer attached to an IP network. Every client and
server station must have a unique IP address. A 32-bit address used by a computer on a IP network. Client
workstations have either a permanent address or one that is dynamically assigned to them each session.
IP addresses are written as four sets of numbers separated by periods; for example, 204.171.64.2.
IPX/SPX. Internet Package Exchange/Sequential Packet Exchange. A communications protocol for Novell. IPX
is Novell’s Layer 3 protocol, similar to XNS and IP, and used in NetWare networks. SPX is Novell's version
of the Xerox SPP protocol.
IS-95. Interim Standard 95. The EIA/TIA standard that governs the operation of CDMA cellular service. Versions
include IS-95A and IS-95B. See CDMA.
K
Kerberos. Kerberos is a network authentication protocol. It is designed to provide strong authentication for
client/server applications by using secret-key cryptography. A free implementation of this protocol is
available from the Massachusetts Institute of Technology. Kerberos is available in many commercial
products as well.
Key. A key is the specific code used by the algorithm to encrypt or decrypt the data. Also see, Encryption and
Decrypting.
L
LAN. Local area network. A radio network that supports data communication within a local area, such as within
a warehouse of building.
LASER. Light Amplification by Stimulated Emission of Radiation.The laser is an intense light source. Light from
a laser is all the same frequency, unlike the output of an incandescent bulb. Laser light is typically coherent
and has a high energy density.
Laser Diode. A gallium-arsenide semiconductor type of laser connected to a power source to generate a laser
beam. This laser type is a compact source of coherent light.
Laser Scanner. A type of bar code reader that uses a beam of laser light.
LCD. See Liquid Crystal Display.
LED Indicator. A semiconductor diode (LED - Light Emitting Diode) used as an indicator, often in digital
displays. The semiconductor uses applied voltage to produce light of a certain frequency determined by the
semiconductor's particular chemical composition.
Glossary - 8 MC50 with Windows Mobile 5.0 User Guide
Light Emitting Diode. See LED.
Liquid Crystal Display (LCD). A display that uses liquid crystal sealed between two glass plates. The crystals
are excited by precise electrical charges, causing them to reflect light outside according to their bias. They
use little electricity and react relatively quickly. They require external light to reflect their information to the
user.
M
®
MAC Address (also called IEEE Address). Spectrum24 devices, like other Ethernet devices, have unique,
hardware-encoded MAC (also called IEEE addresses). MAC addresses determine the device sending or
receiving data. The MAC address is a 48-bit number written as six hexadecimal bytes separated by colons.
MC. Mobile Computer.
MDN. Mobile Directory Number. The directory listing telephone number that is dialed (generally using POTS) to
reach a mobile unit. The MDN is usually associated with a MIN in a cellular telephone -- in the US and
Canada, the MDN and MIN are the same value for voice cellular users. International roaming considerations
often result in the MDN being different from the MIN.
MIL. 1 mil = 1 thousandth of an inch.
MIN. Mobile Identification Number. The unique account number associated with a cellular device. It is broadcast
by the cellular device when accessing the cellular system.
Misread (Misdecode). A condition which occurs when the data output of a reader or interface controller does
not agree with the data encoded within a bar code symbol.
Mobile Computer. In this text, mobile computer refers to the Symbol Series 9000 wireless portable computer. It
can be set up to run as a stand-alone device, or it can be set up to communicate with a network, using
wireless radio technology.
N
NetBeui. A non-routable LAN protocol that is an extension to NetBIOS. Used for IBM’s OS/2-based LAN
Manager and Microsoft’s LAN Manager and Windows for Workgroups.
NetID. For mobile computers using Spectrum24 radios with the Spring protocol, a NetID allows facilities to limit
which Access Points a mobile computer can communicate with. It is set on the Network tab of the Control
Panel. The mobile computer can only communicate with Spectrum24 Access Points that have matching
NetIDs. Also see ESS_ID.
Nominal. The exact (or ideal) intended value for a specified parameter. Tolerances are specified as positive
and negative deviations from this value.
Nominal Size. Standard size for a bar code symbol. Most UPC/EAN codes are used over a range of
magnifications (e.g., from 0.80 to 2.00 of nominal).
Glossary - 9
NVM. Non-Volatile Memory.
O
ODI. See Open Data-Link Interface.
Open Data-Link Interface (ODI). Novell’s driver specification for an interface between network hardware and
higher-level protocols. It supports multiple protocols on a single NIC (Network Interface Controller). It is
capable of understanding and translating any network information or request sent by any other
ODI-compatible protocol into something a NetWare client can understand and process.
Open System Authentication. Open System authentication is a null authentication algorithm.
P
PAN. Personal area network. Using Bluetooth wireless technology, PANs enable devices to communicate
wirelessly. Generally, a wireless PAN consists of a dynamic group of less than 255 devices that
communicate within about a 33-foot range. Only devices within this limited area typically participate in the
network.
Parameter. A variable that can have different values assigned to it.
Percent Decode. The average probability that a single scan of a bar code would result in a successful decode.
In a well-designed bar code scanning system, that probability should approach near 100%.
PING. (Packet Internet Groper) An Internet utility used to determine whether a particular IP address is online. It
is used to test and debug a network by sending out a packet and waiting for a response.
Print Contrast Signal (PCS). Measurement of the contrast (brightness difference) between the bars and
spaces of a symbol. A minimum PCS value is needed for a bar code symbol to be scannable. PCS = (RL -
RD) / RL, where RL is the reflectance factor of the background and RD the reflectance factor of the dark
bars.
Programming Mode. The state in which a scanner is configured for parameter values. See Scanning Mode.
Q
Quiet Zone. A clear space, containing no dark marks, which precedes the start character of a bar code symbol
and follows the stop character.
QWERTY. A standard keyboard commonly used on North American and some European PC keyboards.
“QWERTY” refers to the arrangement of keys on the left side of the third row of keys.
Glossary - 10 MC50 with Windows Mobile 5.0 User Guide
R
RAM. Random Access Memory. Data in RAM can be accessed in random order, and quickly written and read.
Reflectance. Amount of light returned from an illuminated surface.
Resolution. The narrowest element dimension which is distinguished by a particular reading device or printed
with a particular device or method.
RF. Radio Frequency.
ROM. Read-Only Memory. Data stored in ROM cannot be changed or removed.
Router. A device that connects networks and supports the required protocols for packet filtering. Routers are
typically used to extend the range of cabling and to organize the topology of a network into subnets. See
Subnet.
RS-232. An Electronic Industries Association (EIA) standard that defines the connector, connector pins, and
signals used to transfer data serially from one device to another.
S
Scan Area. Area intended to contain a symbol.
Scanner. An electronic device used to scan bar code symbols and produce a digitized pattern that corresponds
to the bars and spaces of the symbol. Its three main components are:
1. Light source (laser or photoelectric cell) - illuminates a bar code.
2. Photodetector - registers the difference in reflected light (more light reflected from spaces).
3. Signal conditioning circuit - transforms optical detector output into a digitized bar pattern.
Scanning Mode. The scanner is energized, programmed and ready to read a bar code.
Scanning Sequence. A method of programming or configuring parameters for a bar code reading system by
scanning bar code menus.
SDK. Software Development Kit
Self-Checking Code. A symbology that uses a checking algorithm to detect encoding errors within the
characters of a bar code symbol.
Shared Key. Shared Key authentication is an algorithm where both the AP and the MU share an authentication
key.
SID. System Identification code. An identifier issued by the FCC for each market. It is also broadcast by the
cellular carriers to allow cellular devices to distinguish between the home and roaming service.
Glossary - 11
SMDK. Symbol Mobility Developer’s Kit.
Soft Reset. See Warm Boot.
Space. The lighter element of a bar code formed by the background between bars.
Spectrum24. Symbol’s frequency-hopping, spread spectrum cellular network.
Specular Reflection. The mirror-like direct reflection of light from a surface, which can cause difficulty decoding
a bar code.
Spread Spectrum. A technique for uniformly distributing the information content of a radio signal over a
frequency range larger than normally required for robust transmission of data. Spreading the signal without
adding additional information adds significant redundancy, which allows the data to be recovered in the
presence of strong interfering signals such as noise and jamming signals. The primary advantage of spread
spectrum technology is its ability to provide robust communications in the presence of interfering signals.
Spring Radio Protocol. A radio protocol that may be used by the Symbol Spectrum24 radio card. Symbol
Radio cards that use the Spring protocol also have an Net ID.
Start/Stop Character. A pattern of bars and spaces that provides the scanner with start and stop reading
instructions and scanning direction. The start and stop characters are normally to the left and right margins
of a horizontal code.
STEP. Symbol Terminal Enabler Program.
Subnet. A subset of nodes on a network that are serviced by the same router. See Router.
Subnet Mask. A 32-bit number used to separate the network and host sections of an IP address. A custom
subnet mask subdivides an IP network into smaller subsections. The mask is a binary pattern that is
matched up with the IP address to turn part of the host ID address field into a field for subnets. Default is
often 255.255.255.0.
Substrate. A foundation material on which a substance or image is placed.
Symbol. A scannable unit that encodes data within the conventions of a certain symbology, usually including
start/stop characters, quiet zones, data characters and check characters.
Symbol Aspect Ratio. The ratio of symbol height to symbol width.
Symbol Height. The distance between the outside edges of the quiet zones of the first row and the last row.
Symbol Length. Length of symbol measured from the beginning of the quiet zone (margin) adjacent to the start
character to the end of the quiet zone (margin) adjacent to a stop character.
Symbology. The structural rules and conventions for representing data within a particular bar code type (e.g.
UPC/EAN, Code 39, PDF417, etc.).
Glossary - 12 MC50 with Windows Mobile 5.0 User Guide
T
TCP/IP. (Transmission Control Protocol/Internet Protocol) A communications protocol used to internetwork
dissimilar systems. This standard is the protocol of the Internet and has become the global standard for
communications. TCP provides transport functions, which ensures that the total amount of bytes sent is
received correctly at the other end. UDP is an alternate transport that does not guarantee delivery. It is
widely used for real-time voice and video transmissions where erroneous packets are not retransmitted. IP
provides the routing mechanism. TCP/IP is a routable protocol, which means that all messages contain not
only the address of the destination station, but the address of a destination network. This allows TCP/IP
messages to be sent to multiple networks within an organization or around the world, hence its use in the
worldwide Internet. Every client and server in a TCP/IP network requires an IP address, which is either
permanently assigned or dynamically assigned at startup.
Telnet. A terminal emulation protocol commonly used on the Internet and TCP/IP-based networks. It allows a
user at a terminal or computer to log onto a remote device and run a program.
Terminal. See Mobile Computer.
Terminal Emulation. A “terminal emulation” emulates a character-based mainframe session on a remote
non-mainframe terminal, including all display features, commands and function keys. The MC9000 Series
supports Terminal Emulations in 3270, 5250 and VT220.
TFTP. (Trivial File Transfer Protocol) A version of the TCP/IP FTP (File Transfer Protocol) protocol that has no
directory or password capability. It is the protocol used for upgrading firmware, downloading software and
remote booting of diskless devices.
Tolerance. Allowable deviation from the nominal bar or space width.
Transmission Control Protocol/Internet Protocol. See TCP/IP.
Trivial File Transfer Protocol. See TFTP.
U
UDP. User Datagram Protocol. A protocol within the IP protocol suite that is used in place of TCP when a reliable
delivery is not required. For example, UDP is used for real-time audio and video traffic where lost packets
are simply ignored, because there is no time to retransmit. If UDP is used and a reliable delivery is required,
packet sequence checking and error notification must be written into the applications.
UPC. Universal Product Code. A relatively complex numeric symbology. Each character consists of two bars
and two spaces, each of which is any of four widths. The standard symbology for retail food packages in the
United States.
V
Visible Laser Diode (VLD). A solid state device which produces visible laser light.
Glossary - 13
W
Warm Boot. A warm boot restarts the mobile computer by closing all running programs. All data that is not
saved to flash memory is lost.
WEP. Wired Equivalent Privacy, is specified by IEEE for encryption and decryption of RF (wireless)
communications.
WEP Encryption. (Wired Equivalent Privacy encryption) The conversion of data into a secret code for
transmission over a public network. The original text, or plaintext, is converted into a coded equivalent called
ciphertext via an encryption algorithm. The ciphertext is decoded (decrypted) at the receiving end and
turned back into plaintext. The encryption algorithm uses a key, which is a binary number that is typically
from 40 to 128 bits in length. The greater the number of bits in the key (cipher strength), the more possible
key combinations and the longer it would take to break the code. The data is encrypted, or “locked,” by
combining the bits in the key mathematically with the data bits. At the receiving end, the key is used to
“unlock” the code and restore the original data.
Wireless Local Area Network (WLAN). See LAN.
WNMP. (Wireless Network Management Protocol) This is Symbol’s proprietary MAC layer protocol used for
inter access point communication and other MAC layer communication.
®
®
WNMS (renamed to AirBEAM Manager). See AirBEAM Manager.
Glossary - 14 MC50 with Windows Mobile 5.0 User Guide
Index - 2
MC50 with Windows Mobile 5.0 User Guide
camera
communication
E
enterprise mobility support . . . . . . . . . . . . . . . . . . . . . .xii
F
companion programs
infrared receive . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
conventions
cradles
H
handstrap
I
infrared
IR
infrared receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
K
keyboard
keypad
D
data capture
DCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xi
device configuration package . . . . . . . . . . . . . . . . . . . .xi
L
Index - 3
SMDK for eVC4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
soft reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
Symbol Mobility Developer Kit for eVC4 . . . . . . . . . . . xi
M
main battery
mobile computer
soft reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
Motorola enterprise mobility support . . . . . . . . . . . . . . xii
T
N
U
UBC
O
P
R
S
scanning
screen
Index - 4
MC50 with Windows Mobile 5.0 User Guide
Motorola, Inc.
One Motorola Plaza
Holtsville, New York 11742-1300
72E-89337-01
Revision A - May 2007
|
