i296
User’s Guide
Class B Digital Device
DECLARATION OF CONFORMITY
Per FCC CFR 47 Part 2 Section 2.1077(a)
As a personal computer peripheral, this device complies with part 15 of
the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. See 47 CFR Sec. 15.19(3).
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
Responsible Party Name: Motorola, Inc.
Address: 8000 West Sunrise Boulevard
Plantation, FL 33322 USA
Phone Number: 1 (800) 453-0920
Hereby declares that the product:
Product Name: i296
Model Number: H88XAH6JR2AN
FCC-ID: IHDP56KY1
Conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a)
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
FCC Notice to Users
•
Consult the dealer or an experienced radio/TV technician for
help.
The following statement applies to all products that have
received FCC approval. Applicable products bear the FCC logo,
and/or an FCC ID in the format FCC-ID: IHDP56KY1 on the product
label.
Motorola has not approved any changes or modifications to this device by
the user. Any changes or modifications could void the user’s authority to
operate the equipment. See 47 CFR Sec. 15.21.
Industry Canada Notice to Users
Operation is subject to the following two conditions: (1) This device may
not cause interference and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
See RSS-GEN 7.1.5.
This Class B digital apparatus complies with Canadian ICES-003.
Motorola, Inc.
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. BOOST, BOOST and Logo, Re-Boost,
and Logo are trademarks of Boost Worldwide, Inc. Java and all
other Java-based marks are trademarks or registered trademarks
of Sun Microsystems, Inc. in the U.S. and other countries.
Microsoft, Windows, Windows Me, and Windows Vista are
registered trademarks of Microsoft Corporation in the United
States and other countries. T9 is a trademark owned by Tegic
Communications. All other product or service names are the
property of their respective owners.
Consumer Advocacy Office
600 N US Highway 45
Libertyville, IL 60048
Note: Do not ship your phone to the above address. If you need to
return your phone for repairs, replacement, or warranty service,
please contact the Motorola Customer Support Center at:
1-800-453-0920 (United States)
1-877-483-2840 (TTY/TDD United States for hearing impaired)
Important Privacy Message: Boost's policies often do not apply
to third-party applications. Third-party applications may access
your personal information or require Boost to disclose your
customer information to the third-party application provider. To
find out how a third-party application will collect, access, use, or
disclose your personal information, check the application
provider’s policies, which can usually be found on their website. If
you aren't comfortable with the third-party application’s policies,
don't use the application.
Certain mobile phone features are dependent on the capabilities
and settings of your service provider’s network. Additionally,
certain features may not be activated by your service provider,
and/or the provider's network settings may limit the feature’s
functionality. Always contact your service provider about feature
availability and functionality. All features, functionality, and other
product specifications, as well as the information contained in this
user's guide are based upon the latest available information and
are believed to be accurate at the time of printing. Motorola
reserves the right to change or modify any information or
specifications without notice or obligation.
© 2010 Motorola, Inc. All rights reserved.
© 2010 Boost Worldwide, Inc. All rights reserved. Boost, Boost
Mobile and the Logo are trademarks of Boost.
®
T9 Text Input Patent and Trademark Information.
Manual Number: NNTN7917A
This product is covered by U.S. Pat. 5,818,437, U.S. Pat. 5,953,541,
U.S. Pat. 6,011,554 and other patents pending.
HELLOMOTO
Introducing your new Motorola wireless phone. Here’s a quick anatomy lesson.
Right Soft Key
Perform function
in lower right
display.
Left Soft Key
Perform function
in lower left
display.
Volume Keys
WT Button
Menu Key
From home screen,
open main menu.
2.5mm Audio
Jack
End/Power Key
End calls, exit
menu system,
turn phone on/off.
Speaker Key
On/Off Key
Micro USB
Connector
Connects charger
and accessories.
Talk Key
Make &
answer calls.
OK Key
In menus & lists,
press to select
highlighted
option.
4-Way Navigation
Key
1
check it out
1
3
Press and hold the
Power Key for a
Press the Navigation Key
up, down, left or right
Ready
10:05pm 10/23
Mesgs
few seconds, or until
the screen lights up,
to turn on your phone.
to highlight a menu feature.
Contcs
2
/
Press the Menu Key
4
to open the main menu.
Press the
r
key
to select.
2
contents
check it out . . . . . . . . . . . 2
call a stored
phone number or
walkie-talkie ID . . . . . . 16
find your phone
number and
walkie-talkie ID . . . . . . 17
messaging . . . . . . . . . 17
datebook. . . . . . . . . . . 24
basics. . . . . . . . . . . . . . . 26
display . . . . . . . . . . . . 26
main menu . . . . . . . . . 27
text entry . . . . . . . . . . 27
volume . . . . . . . . . . . . 30
navigation key. . . . . . . 31
handsfree speaker . . . 31
transmitters off. . . . . . 31
use GPS with
features for the
hearing impaired. . . . . 32
TTY . . . . . . . . . . . . . . . 33
security features. . . . . 34
main attractions . . . . . . 35
media center . . . . . . . 35
Get Stuff . . . . . . . . . . . 36
walkie-talkie features . 36
one touch WT. . . . . . . 41
WT service . . . . . . . . . 42
Bluetooth® wireless. . 42
call features. . . . . . . . . . 46
turn off a call alert. . . . 46
recent calls . . . . . . . . . 46
redial. . . . . . . . . . . . . . 47
caller ID . . . . . . . . . . . 47
call forward. . . . . . . . . 48
(continued next page)
essentials . . . . . . . . . . . . 7
about this guide . . . . . . 7
SIM card. . . . . . . . . . . . 8
battery . . . . . . . . . . . . . 8
turn it on & off . . . . . . . 11
enable security. . . . . . . 11
make a phone call. . . . 12
answer a phone call . . 12
advanced calling . . . . . 12
make a
walkie-talkie call . . . . . 13
answer a
walkie-talkie call . . . . . 14
store a phone number
or walkie-talkie ID. . . . 15
contacts . . . . . . . . . . . 16
map software . . . . . . . 31
contents
3
call features (continued)
voice names . . . . . . . . 48
emergency calls . . . . . 49
international calls. . . . . 50
speed dial . . . . . . . . . . 50
voicemail . . . . . . . . . . . 50
customize. . . . . . . . . . . . 52
ringtones . . . . . . . . . . . 52
backlight . . . . . . . . . . . 53
wallpaper. . . . . . . . . . . 53
hide or show location . 54
Safety, Regulatory
& Legal . . . . . . . . . . . . . . 56
index. . . . . . . . . . . . . . . . 75
contents
4
menu map
main menu
l
U
Q
Re-Boost
Get Stuff
WT Service
f
X
Profiles
b
g
a
i
Datebook
Voice Notes
Memo
My Info
•
•
•
•
My Name
Line 1
•
•
•
•
•
Send Pictures
Walkie-Talkie #
Carrier IP
GPS
Send Event
Send My Info
Send Contact
Configure
•
•
•
Position
Privacy
Interface
T
Ringtones
•
•
•
•
•
Buy Ringtones
Vibrate All
Ringers (1-12)
Vibrate
d
Call Forward
S
c
e
Web
•
•
Forward
To
Recent Calls
Silent
Contacts
W
V
Call Alert
Y
Messages
•
•
[New Contact]
[New Msg Group]
•
•
•
•
•
•
•
[Create Message]
Call Timers
Voice Mail
Inbox
•
•
•
•
•
•
Last Call
R
r
Settings
Phone Reset
Phone Lifetime
WT Reset
Drafts
•
(see next page)
Outbox
Net Alert
Sent Items
Bluetooth®
WT Lifetime
Kbytes Reset
•
•
•
•
•
Hands Free
Link to Devices
Device History
Setup
Z
h
Games & Apps
j
Media Center
Shortcuts
Find Me
This is the standard Main Menu layout.
Your phone’s menu may be a little different.
menu map
5
settings menu
•
Display/Info
•
•
WT Options
•
Volume
•
•
•
•
•
•
•
•
•
Wallpaper
Text Size
Theme
•
•
•
•
•
One Touch WT
•
•
•
•
•
•
•
•
Line 1
Alert Type
Messages
Earpiece
WT Quick Notes
On/Off WT Features
Store Rcvd Info
Home Icons
Backlight
Clock
Menu View
Large Dialing
Language
Speaker
Keypad
Java™ Earpiece
Java™ Speaker
Data
Personalize
•
•
•
•
•
•
•
•
•
Menu Options
Up Key
•
•
Security
Down Key
Left Key
Right Key
Center Key
Left Sftkey
Right Sftkey
Power Up
•
Phone Calls
•
•
•
•
•
Phone Lock
•
•
•
•
•
•
•
•
•
•
•
Set Line
Keypad Lock
SIM PIN
Any Key Ans
Auto Redial
Call Waiting
Auto Ans
GPS PIN
Change Passwds
Advanced
Minute Beep
Call Duration
TTY
Hearing Aid
Notifications
DTMF Dialing
•
•
•
•
•
•
•
Alert Timeout
Headset/Spkr
Connectivity
Reset Defaults
Return to Home
Transmitters
Baud Rate
menu map
6
essentials
Caution: Before using the phone for the first
time, read the important “Safety, Regulatory
& Legal” information included in the
3
Press the navigation keys to scroll to
Phone Calls, and press to select it.
r
symbols
gray-edged pages at the back of this guide.
This means a feature is network or
subscription dependent and may
not be available in all areas. Contact
customer service for more
information.
about this guide
This guide shows how to locate a menu
feature as follows:
This means a feature requires an
optional accessory.
Find it:
/
>
R Settings
>
Phone Calls
This means that, from the home screen:
1
2
Press the menu key
/
to open the main
Note: Because of updates in phone software,
this printed guide may not be the most
current version for your phone. Visit
the most recent version of the user’s guide.
menu.
Press the navigation keys to scroll to
R Settings, and press the center key
select it.
r
to
essentials
7
Important: Do not touch the gold-colored
areas of your SIM card.
SIM card
Note: Protect your SIM card as you would any
delicate object. Store it carefully.
inserting & removing the
SIM card
battery
Note: Please review “Battery Use &
Safety” on page 56 before using your phone.
Warning: Use only Motorola-approved
batteries and chargers with your phone.
Failure to use a Motorola-approved battery or
charger may increase the risk that your phone
will overheat, catch fire, or explode, resulting
in serious bodily injury, death, or property
damage.
Warning: To avoid damaging or losing
information stored on your SIM card, do not
remove the SIM card from your phone unless
absolutely necessary.
essentials
8
battery charging
New batteries are not fully charged.
Warning: Do not handle a damaged or leaking
Li-ion battery as you can be burned.
Note: Long backlight settings, searching for
service, vibrate mode, browser use, and other
variables may reduce the battery’s talk and
standby times.
charge using the charger
Pull out the connector cover, rotate it, and
insert the charger into the micro USB
connector on your phone as shown.
charge from your
computer
You can partially charge your phone’s battery
by connecting a Motorola-approved USB cable
from your phone’s micro USB connector to a
high power USB connector on a computer
(not a low-power one, such as the USB
connector on your keyboard or bus-powered
USB hub). Typically, USB high-power
essentials
10
connectors are located directly on your
computer.
turn it on & off
To turn on your phone,
press and hold the
battery indicators
d
e
f
g
The battery is between 90% and
100% capacity when the indicator is
blue and displaying three bars.
The battery is at approximately 65%
capacity when the indicator is green
and displaying two bars.
The battery is at approximately 10%
capacity when the indicator is yellow
and displaying one bar.
The battery is at approximately 5%
capacity when the indicator is red
and has a flashing red bar.
power key
@
for a few
seconds or until the display
turns on. If prompted, enter your four-digit
unlock code.
Note: If you press
@
for more than four
seconds, the phone will turn on in
transmitters off mode. See “transmitters off”
on page 31.
To turn off your phone, press and hold
a few seconds.
@
for
enable security
h
The battery is charging.
You will need to enable security the first time
you power on your phone, or within 10 days of
the first time you activate the phone.
1
Press
K
under Ok.
essentials
11
2
3
You are prompted to enable security.
Press under Yes and follow on screen
instructions.
•
If you are using a Bluetooth® headset,
press the answer key on your headset.
To hang up press the key again.
K
Press to return to the home screen.
@
Note: When your phone is off, calls go directly
to voicemail.
make a phone call
Enter a phone number and press the
advanced calling
feature
talk key
`
or use a voice command. See
“place a call using a voice name” on page 49.
callwaiting To accept the second call
To hang up press
@
.
K
To accept the second call
and end the active call,
answer a phone call
•
To answer the call on speakerphone,
press the speaker key
press
`.
)
.
•
To answer the call using the phone,
press . To hang up press
`
@.
essentials
12
feature
make a walkie-talkie call
You can use your phone as a long-range,
digital two-way radio using one-to-one
walkie-talkie calls.
3-way call
Note: 3-way calling lets you
talk with two other people at
the same time. When using
this feature, the normal
airtime rates will be charged
for each of the two calls.
Your walkie-talkie ID (private ID) is the number
at which you receive one-to-one walkie-talkie
calls.
Make or receive a phone call
To make a walkie-talkie call:
and press
the second phone number,
press and under Join.
/
>
3 Way. Enter
1
Enter the walkie-talkie ID you want to call.
`
K
Tip: Be sure to entire the entire number,
including the asterisks.
You cannot make any other
calls during a three-way call,
even if one party hangs up.
2
3
Press and hold the WT button. Begin
talking after your phone emits a chirping
sound.
any key
answer
To answer phone calls by
pressing any keypad key,
Release the WT button to listen.
press
/
>
>
R Settings
Any Key Ans
>
Phone Calls
>
On.
To end the call press
@.
essentials
13
Note: A walkie-talkie call ends automatically if
there is no activity on the call for a few
seconds.
3
When Ready To Alert appears in the display,
press the WT button until you see
Alert Successful
.
Note: The number of digits in each part of a
walkie-talkie ID (Private ID) may vary. For
example, your walkie-talkie ID may be
formatted as 999*999*9999, while another
valid number may appear as 555*555555*55.
answer a walkie-talkie
call
1
When your phone emits a chirping sound
or vibrates to indicate you are receiving a
walkie-talkie call, wait for the caller to
finish speaking.
send call alerts
Sending a call alert discretely lets the
recipient know that you want to talk to him or
her on a walkie-talkie call.
2
3
Press and hold the WT button and begin
talking after your phone emits a chirping
sound.
When you send a call alert, the recipient’s
phone displays your name or walkie-talkie ID,
and emits a series of beeps or vibrations.
Release the WT button to listen.
To end the call press
@.
To send a call alert:
1
2
Enter the walkie-talkie ID you want to call.
Press under Alert
K
.
essentials
14
1
Enter a name for the new entry, then
answer a call alert
When you receive a call alert, you cannot
receive phone calls or walkie-talkie calls until
you do one of the following:
press
r. The entry’s name can contain
up to 20 characters.
2
3
Select a Ringer, then press
r
.
Select the entry type (Mobile
,
Walkie-Talkie,
option
Work1 Work2 Home Email Fax Pager, Msg Group,
,
,
,
,
,
Answer
Queue
Clear
Press the WT button to begin a
walkie-talkie call with the sender.
IP, or Other). To store a walkie-talkie ID,
choose Walkie-Talkie
.
Press
call alert to the call alert queue.
Press under Clear to dismiss
and delete the call alert.
K
under Queue to store the
4
Enter the number for the entry, then
press
r
.
K
Tip: When you store a walkie-talkie ID, be
sure to entire the entire number, including
the asterisks.
store a phone number
or walkie-talkie ID
5
Press
K
under Save to save the entry.
ICE - In Case of Emergency
You can store a phone number or walkie-talkie
To make it easier for emergency personnel to
identify important contacts, you can list your
local emergency contacts under “ICE” in your
phone’s contact list. For example, if your
ID (private ID) in Contacts
:
Find it:
/
>
e Contacts
>
[New Contact]
essentials
15
mother is your primary emergency contact,
list her as “ICE–Mom” in your contact list. To
list more than one emergency contact, use
“ICE1–___,” “ICE2–___,” etc.
call a stored phone
number or walkie-talkie
ID
Find it:
/
>
e Contacts
contacts
feature
1
2
Highlight the Contacts entry.
If the entry contains more than one
number, scroll left or right until the
number you want to call is displayed
edit/delete
contact
entry
Press
Highlight a contact and
press Edit. Change the
desired content, then
K
under Contcs.
/
>
(Mobile, Walkie-Talkie, Work1, Work2, Home, etc.).
3
If you chose a phone number, press
call the number.
`
to
press
K
under Done
.
set ringer ID Press
K
under Contcs.
or
Highlight a contact and
press Edit. Select Ringer
and chose your desired
ringtone. Press under
/
>
If you chose a walkie-talkie ID, press and
hold the WT button to call the number.
K
Done
.
essentials
16
3
Optionally, insert (embed) or attach a
picture, sound, or quick note:
find your phone number
and walkie-talkie ID
•
Quick notes are short, pre-written
phrases. Press
a quick note.
K
under QNotes to enter
Find it:
/
>
X My Info
•
To insert pictures, sounds (audio files),
or voice recordings into the body of
messaging
You can send and receive text messages
(SMS) and multimedia messages (MMS).
your message, press
/
>
Insert
>
Add QNotes
,
Add Picture, Insert Audio, or
Record Voice
.
create & send messages
Note: You can only insert one item at a
time. To remove an item from a
message, highlight it and press
under Delete
Find it:
/
>
Y Messages
>
[Create Message]
K
1
Enter the phone number of the person
you want to send the message to and
.
press
r, or press
K
under Search to
•
To attach a file to the end of your
message, select ....MORE....
select a contact or recent call.
>
Attach
>
[New]
>
Browse Pictures or Browse Audio or
.
2
Enter your message in the Mesg field.
Record Voice
essentials
17
Note: You can only attach pictures and
audio files if they are not forward
locked and if they are not
To read your messages later, press
/
>
Y Messages
>
Inbox.
manage received messages
DRM-protected.
feature
Tip: To remove an attachment, select
Attach. Select the attachment to remove,
forward a
message
Highlight the message and
press
and press
/
>
Unattach.
/
>
Forward.
4
When finished writing your message,
Embedded objects and
attachments are also
forwarded.
press r.
5
To send the message, press
K
under
reply to a
message
Open the message and
Send.
press
K
under Reply to reply
to the sender only.
receive messages
For MMS messages you can
also reply to all recipients:
When you receive a message, your phone
plays an alert and shows a notification.
Press
/
and select Reply All.
•
To view the message, press
K
under
Select [Create Reply] to create
your message, or select a
short phrase from the list.
Read
.
•
To dismiss the message notification,
press under Exit
K
.
essentials
18
feature
feature
view, play,
or open an
embedded
object or
Highlight the embedded
picture or audio file to view
or play it.
delete a
message
Highlight the message and
press
Press
K
K
under Delete
.
under Yes to
confirm.
For attachments, press
r.
attachment
Note: Attachments of an
unknown type cannot be
opened, but can be deleted.
message groups
You can create a message group to send
messages to groups of up to 20 contacts.
save an
embedded
object
Highlight the picture or
audio file and press
/
create message groups
Find it: /
>
Save Picture or Save Audio.
>
e Contacts > [New Msg Group]
save an
attachment and press
Highlight the attachment
1
Select [Add Member] and select the contacts
you want to add to the group.
/
>
Save Attachment.
2
When you are finished adding members
to the group, press
delete an
embedded
object or
Highlight the embedded
picture, audio file, or
K
under Done.
attachment and press
/
attachment
>
Delete Picture or Delete Audio, or
Delete Attachment
.
essentials
19
3
Type a name for the message group in the
Name field.
feature
add
Press
highlight the message group
and press
[Add Member]. Select the
contact(s) you want to add
/
>
e Contacts,
Note: If you do not provide a name for the
message group, the default name will be
Msg Group followed by the number of group
members. For example, a message group
with three members would be named
members
/
>
Edit
>
and press
Press
K
under Done
under Save
e Contacts
.
Msg Group (3)
.
K
.
4
Press
K
under Save.
remove
members
Press
/
>
,
highlight the message group
and press
Highlight the member to
remove and press
manage message groups
/
>
Edit.
feature
/
view a
message
group
Press
highlight the message group
and press
/
>
e Contacts,
>
Remove Member. Press
under Save
Press
highlight the message group
and press
Delete Msg Group. Press
under Yes to confirm
K
.
r
.
delete a
message
group
/
>
e Contacts,
/
>
K
.
essentials
20
multimedia message options
option
Multimedia messages (MMS) contain text,
pictures, and audio files. When you create an
MMS message, you have more options than
for a simple text message.
Valid Until
Set a date after which attempts
to deliver the message end, or
press
K
under No Date.
manage your messages
When creating the message, select ....MORE....
for these options:
cleanup messages
option
Set how long and/or how many messages are
stored in the inbox and sent items folders.
This feature deletes only read messages,
unlocked messages, and sent messages.
Subject
Attach
Create or edit the subject line.
Attach a picture, audio file, or
voice record.
Find it:
/
>
Y Messages, press
/
>
Setup
Cc
Send a copy of the message to
someone else.
>
Cleanup
1
Select Inbox or Sent Items
.
Auto Replies Create a list of short answers
for the recipient to choose
when replying to your
message.
Priority
Set priority Normal or High.
essentials
21
2
Choose a cleanup option from the
following list:
option
Custom
Specify clean-up settings of up
to 199 messages or 99 days for
the inbox and sent items.
option
Off
Messages are never
automatically deleted.
3
Press
K
under Yes to automatically delete
5 Messages Messages are deleted in the
order they were received,
starting with the oldest, until
five are left.
messages now, or press
delete messages later.
K
under No to
message threads
1
0 Messages Messages are deleted in the
order they were received,
starting with the oldest, until
10 are left.
If message threads are supported by your
service provider, you can organize your
messages by subject or sender.
Find it:
> None or Subject or Sender
/
>
Y Messages, press
/
>
Threading
1 Day
Messages are deleted if they
are older than 1 day.
edit & send drafts
Saved unsent messages are stored in the
drafts folder.
3 Days
Messages are deleted if they
are older than 3 days.
F-In F-Out
Messages are deleted as
necessary on a first-in first-out
basis.
Find it:
/
>
Y Messages
>
Drafts
essentials
22
1
2
To edit a draft, select it to open it. You can
change or add recipients, and edit the
message.
feature
resend a
failed
message
Press
Outbox. Highlight the
message and press
under Resend
Press
Outbox. Highlight the
message and press
/
>
Y Messages
>
To send a draft, select it to open it and
K
press
K
under Send. When you send a
.
draft, it is removed from the drafts folder.
cancel an
unsent
message
/
>
Y Messages
Note: To delete a draft without sending it,
>
highlight the message you want to delete
/
and press
K
under Delete. Press
K
under
>
Delete Message
Y Messages
Sent Items. Highlight the
message and press
Forward. Make edits if you
want, then select the
recipient and press
under Send
.
Yes to confirm.
forward a
sent
message
Press
/
>
>
more mesage management
/
feature
>
delete an
unread
message
Press
Inbox. Highlight the
message and press
/
>
Y Messages
K
>
.
K
under Delete. Press
K
under
Yes to confirm.
viewunsent Press
messages
/
Outbox.
>
Y Messages
>
essentials
23
feature
feature
delete a
sent
message
Press
Sent Items. Highlight the
message and press
/
>
Y Messages
event
reminder
When an event reminder
occurs, press under View.
>
K
K
To close the reminder,
press under Back
To view the information while
under Delete. Press
K
under
K
.
Yes to confirm.
receive
datebook still in a walkie-talkie call,
events via press
WT
datebook
feature
r.
The five most recent events
received from a walkie-talkie
ID are stored with that
walkie-talkie ID on the recent
calls list.
create
datebook event, press
events
see
datebook press
To create a new datebook
/
>
b Datebook
and press
To see a datebook event,
b Datebook. Scroll
K
under New.
To store events to the
/
>
datebook, press
K
under Save
event
to the date and select it, then
scroll to the event and
select it.
while viewing the event you
want to store.
essentials
24
datebook setup
options
Find it:
/
>
b Datebook, press
/
>
Setup
Alert
Timeout
Sets the amount of time a tone
continues to sound when you
receive a datebook reminder.
You can view or change the following options:
options
Clock
Controls whether the time and
date appear on the home
screen; sets time and date
format; sets year.
Start View Sets the datebook to start in day
view, week view, or month
view.
Daily Begin Sets the beginning of your day.
This is the earliest time of day
displayed in week view, if you
have a 12-hour day view.
Delete After Sets the amount of time the
datebook waits to delete an
event after it occurs.
Time Shift
Lets you shift the times of all
datebook events. This is useful
if you are traveling to a different
time zone.
essentials
25
basics
See page 1 for a basic phone diagram.
status indicators
Status indicators are shown at the top of the
home screen:
display
1 2 3 4
5
6
7
The home screen appears when you turn on
the phone. To dial a number from the home
screen, press number keys and
`.
Note: Your home screen may look different.
Ready
10:05pm 10/23
Contcs
Mesgs
Time &
Date
1
Signal Strength Indicator: Vertical bars
show the strength of the network
connection. You can’t make or receive
Ready
10:05pm 10/23
Left Soft
Key Label
Right Soft
Key Label
Contcs
Mesgs
calls when
~
shows.
Soft key labels show the current soft key
functions. For soft key locations, see page 1.
basics
26
2
3
Active Phone Line:
phone line is ready to make calls.
$
indicates that the
main menu
All your phone’s features can be accessed
through the main menu. You can set the main
Speaker On/Off: Sounds associated with
walkie-talkie calls and group calls can be
set to come through the earpiece rather
than through the speaker.
menu to appear as Icon View or List View
.
Find it: R Settings Display/Info Menu View
/
>
>
>
4
Ringer Vibe/Off: Your phone is set
to ring.
text entry
5
Message Indicator: Shows when
you receive a text message or
voicemail message.
Your phone provides convenient ways to enter
words, letters, punctuation, and numbers
whenever you are prompted to enter text (for
example, when adding a contact entry or
when text messaging).
6
7
Packet Data: Your phone is ready to
transfer packet data or is transferring
packet data when it shows a blinking
arrow.
change the character input method
1
When you see a screen where you can
enter text, press to change the
character input method.
Battery Charge Indicator: A fuller battery
indicates a greater charge. Recharge the
battery when your phone shows Low Battery
/
.
basics
27
2
Select one of the following options:
Tip: When entering text, press and hold
#
abc).
to change letter capitalization (Abc
>
ABC
>
entry method
Alpha
Word
Press a key several times for
word method
The word text input method lets you enter
text into your phone by pressing keys just
once per letter.
different characters.
Enter words using a predictive
text enty system that lets you
enter a word with fewer
keypresses.
The word text input method combines the
groups of letters found on each phone key
with a fast-access dictionary of words, and
recognizes what you want to text as you type.
It first offers the most commonly-used word
for the key sequence you enter and lets you
access other choices with one or more
Symbols
Numeric
Enter symbols.
Enter numbers by pressing the
numbers on the keypad.
Text
Settings
Selects the desired entry
languages and Word Prediction
features.
presses of the
0
key. You may also hold the
navigation key down to display a pop-up list of
Insert
Selects a item to be inserted,
such a picture, an audio clip or a
voice recording.
choices.
enter a word using word method
character input
Note: available only when using
MMS messaging.
1
Select the Word character input method.
basics
28
2
3
Press the corresponding keys once per
letter to enter a word (for example, to
enter the word Bill, press 2 4 5 5).
example, to enter the word Bill, press
twice, three times, three times,
and three times again. If you make a
mistake, press Delete to erase a single
character. Press and hold Delete to erase an
entire word.)
2
4
5
5
(If you make a mistake, press
a single character. Press and hold
delete an entire entry.)
*
to erase
to
*
To accept a word and insert a space,
press
By default, the first letter of an entry is
capitalized and the following letters are
lowercased. When you enter a character, the
cursor automatically advances to the next
space after two seconds, or when you enter a
character on a different key.
#
.
To accept a word completion (such as
Billion when you entered Bill), press the
navigation key right.
If you get a word you don’t want, you can
Characters scroll in the following order:
press
0
to see more word choices and
pick the one you want.
characters
1
Space . 1 ? ! , @ & : ; “ - ( ) ‘ ¿ ¡ %
£ $ ¥
alpha method
To enter characters by tapping the keypad:
2
3
4
A B C 2 Á Ã Â À Ç
D E F 3 É Ê È
G H I 4 Í Ì
1
2
Select the Alpha character input method.
Press the corresponding keys repeatedly
until the desired letter appears. (For
basics
29
characters
character type
5
6
7
8
9
0
#
*
J K L 5
Q
R
S
W
X
or
or
or
T
U
V
Lowercase
Uppercase
Shift Lock
Numerical
Symbols
M N O 6 ñ Ó Õ Ô Ò
P Q R S 7 ß
T U V 8 Ú Ü Û Ù
W X Y Z 9
+ - 0 * / \ [ ] = > < # §
Space / Shift
volume
Press the volume keys up or
down to:
Back
When entering text, press and hold
#
to
•
change the earpiece
volume during calls
switch between lowercase and uppercase
letters. The icons in the upper left-hand corner
of the screen show the character type.
•
change the ringer
volume from the home screen
Tip: You can quickly set your ringer to
Vibrate All by holding the down volume
key in the home screen.
basics
30
navigation key
transmitters off
Press the navigation key
up, down, left, or right to
scroll to items in the
display. When you
Consult airline staff about using the
transmitters off feature during flight. Turn off
your phone whenever instructed to do so by
airline staff.
highlight the desired
The transmitters off feature turns off your
phone’s calling and Bluetooth features in
situations where wireless phone use is
prohibited. You can use the phone’s other
non-calling features when transmitters are
turned off.
item, press
select it.
r
to
handsfree speaker
You can use your phone’s handsfree speaker
to make calls without holding the phone to
your ear.
Find it:
/
>
R Settings
>
Advanced
>
Transmitters
>
Off
During a call, press
handsfree speaker on.
K
under Spkr to turn the
use GPS with map
software
Your phone can be connected to a PC,
laptop, or PDA over a USB cable
The handsfree speaker stays on until you
press under Spkr again, or until you end
the call.
K
connection for use as a GPS receiver. For
basics
31
more specific information on how to set up
your phone for use with your computer please
under the FAQ section.
optimize your phone position and
orientation
While in a phone call slide your phone up and
down, then left and right until best
may need to adjust your hearing aid (HA)
volume setting.
features for the hearing
impaired
using your phone with a
hearing aid
Note: Your phone has a hearing aid rating
of M3. For more information, see “Hearing
Aid Compatibility With Mobile Phones” on
page 69.
If your HA has a telecoil, activate its switch,
then also rotate the phone as illustrated to
align the telecoils.
For best results use the following optimization
procedures and phone setting. They generally
apply as well for users with cochlear implants.
Note: Some automatically switched hearing
aids may need an auxiliary switching magnet.
basics
32
If you are unsure whether your HA is telecoil
equipped or needs an auxiliary magnet,
please refer to your HA user guide or contact
a hearing aid professional or supplier.
The factory default setting for this feature is
Off.
TTY
feature
Approximate telecoil location is within
6-13 mm of this location.
turn on TTY Press
/
>
>
R Settings
TTY Use TTY
Off - Shut off
M - Microphone
T - Telecoil
feature
>
>
Phone Calls
On
>
.
/
>
>
R Settings
TTY Type
TTY or VCO or HCO
R Settings
TTY Baud
45.45 or 50.00
>
.
Approximate telecoil location is just
above the battery.
/
>
>
>
choose your hearing aid setting
.
Find it:
/
>
R Settings
>
Phone Calls
>
Hearing Aid
change TTY While in the TTY call, press
>
Off or Microphone or Telecoil
mode
/
>
In Call Setup
>
TTY
>
Type
The Microphone option optimizes your phone for
microphone coupling. The Telecoil option meets
US federal requirements for telecoil coupling.
during a call
>
TTY or VCO or HCO.
basics
33
Note: You can make emergency calls on a
locked phone (see page 49).
security features
feature
phone lock
To lock the phone, press
/
>
>
R Settings
Phone Lock
Auto Lock
>
Security
>
Lock Now or
.
keypad lock To lock the keypad,
press
/
>
R Settings
Keypad Lock
Lock Now or Auto Lock
>
>
Security
>
.
Shortcut: To lock the
keypad, press
enable SIM Press
PIN
change SIM Press
/
>
*.
/
>
R Settings
SIM PIN On
R Settings
Change Passwords
>
Security
>
>
.
/
>
PIN
>
>
Security
>
SIM PIN
.
basics
34
main attractions
connection. See “messaging” on page 17 and
“Bluetooth® wireless” on page 42.
media center
The media center lets you access pictures and
audio recordings stored in your phone’s
memory.
Pictures in the media center can be sent in
walkie-talkie calls. See “walkie-talkie
features” on page 36.
The following audio recordings can be
accessed through the media center:
Audio files supported by the media center
include:
•
•
•
voice records
ringtones
Format
.au
Sampling Rates/Bit Rates
8 KHz/8 kbps
8 KHz
audio recordings saved from MMS
messages
.midi
.mp3
.wav
.amr
8 KHz/32 kbps
8 KHz/64 kbps
12kbps
•
audio recordings downloaded to your
phone
Items in the media center can be sent in
MMS messages and over a Bluetooth®
main attractions
35
Image files supported by the media center
include:
walkie-talkie features
Your phone can send and receive the
following items through walkie-talkie
calls with other phones that have this
capability:
Format
.png
Max. Image Size (in pixels)
128 x 160
.gif
128 x 160
.jpg
640 x 480
•
•
•
•
pictures
.wbmp
128 x 160
datebook events
My Info
Get Stuff
contact information
Your phone includes a main menu icon that
You can choose to Push-To-Send My Info and
contact information to any walkie-talkie ID.
takes you directly to Get Stuff
.
You can download ringtones, wallpapers and
Java™ applications over the air.
You can choose to send pictures, messages,
events to the walkie-talkie ID you are engaged
in a a walkie-talkie call with, walkie-talkie IDs
on the Recent Calls list, and walkie-talkie IDs
Note: Normal airtime and/or carrier usage
charges apply.
stored in Contacts
.
When you make or receive a walkie-talkie call,
your phone automatically determines whether
the phone you are engaged in a walkie-talkie
main attractions
36
call with is able to receive each of these
items. Your phone saves this information for
as long as the walkie-talkie ID is in your
Recent Calls list or is saved in your Contacts. Your
phone updates the saved information each
time you make or receive a call to or from that
walkie-talkie ID.
If the recipient accepts the picture, their
phone saves the picture.
The first time you send a stored picture after
turning your phone on, the phone shows
Picture Fees May Apply. Continue? and prompts you to
respond.
Note: You cannot make or receive
walkie-talkie calls while transmitting or
receiving a picture.
You can turn your phone’s ability to send and
receive messages, pictures, events on and
off.
Tip: When you send My Info, certain
information, such as your email address or fax
number, cannot be included. To send
complete contact information, create an entry
for yourself in contacts and send it.
send a picture during a call
1
While in a walkie-talkie call, press
under Picture or press
Send Picture
K
/
>
Use WT Feature
>
.
A list of pictures that can be included in a
walkie-talkie call appears.
send pictures
2
3
Select the picture you want to send.
You can send pictures stored in the
media center through walkie-talkie calls. The
picture you send appears on the walkie-talkie
call recipient’s display.
Press the WT button to send the picture.
main attractions
37
4
Wait while the picture is transmitted. The
walkie-talkie call is temporarily interrupted
while a picture is transmitted.
5
When prompted, press the WT button to
resume the walkie-talkie call.
To send a picture from the WT service
:
5
When prompted, press the WT button to
resume the walkie-talkie call.
Find it:
/
>
Q WT Service
>
Send Picture
1
2
Select A Contact, or A Recent Call to see a list of
entries that can receive pictures.
start a call by sending a picture
To send a picture from the media center
Select the entry containing the
walkie-talkie ID you want to send the
picture to.
:
Find it:
/
>
j Media Center
1
2
Select the picture you want to send.
Press Send Picture.
3
4
5
Select the picture you want to send.
/
>
Use WT Feature
>
Press the WT button to send the picture.
A list of contacts that have walkie-talkie
IDs and are able to receive pictures
appears.
Once the picture has been sent, when
prompted press the WT button to resume
the call.
3
Select the name of the person you want
to send the picture to.
4
Press the WT button to send the picture.
main attractions
38
receive a picture
clear a picture from the display
When someone sends you a picture, your
phone emits a tone or vibrates and a message
appears asking if you want to accept the
picture.
If you want to clear a picture from your
phone’s display while on a call, press
/
>
Clear Screen.
The picture will not appear on the display
again the next time you receive a call from the
person who sent it. This does not delete the
picture from the media center.
Pictures you receive are saved to your phone’s
memory. They are accessible through the
media center.
When you see a message asking if you want
to accept the picture, press Yes to accept or No
to decline.
send my info
While in a walkie-talkie call, press
/
>
Send via WT, and push the WT button to send.
Tip: If you want to stop the transmission
before it is finished, press
@.
Alternatively, from the home screen
,
press My Info, then press Send via WT
/
>
/
>
Note: The first time you accept a stored
picture after turning your phone on, the phone
shows Picture Fees May Apply. Continue? and prompts
and push the WT button to send.
set my info sending option
You can control what portion of the
information in My Info is sent and
you to respond. Press
the picture.
K
under Yes to accept
main attractions
39
whether it is sent automatically in every call or
only when you choose to send it.
When you make a call in which your
information is sent automatically, the name
you entered in the My Name field of My Info
appears on the display of the recipient’s
phone, even if your name and walkie-talkie ID
are not stored in the recipient’s contact list.
Find it:
/
>
>
Q WT Service
Info to Send
>
Configure
>
WT My Info
1
Select or remove the fields you want to
send.
send contact information
2
Press
K
under Done.
While in a walkie-talkie call
:
The information your phone sends always
includes My Name and Walkie-Talkie. You may also
1
2
Press
/
>
Use WT Feature.
send Line 1 Carrier IP, and Circuit Data depending on
,
Select Send Contact and select the contact
information you want to send.
your sending options.
automatic sending
To control whether you send your information
automatically:
3
Push the WT button to send.
Alternatively, from the home screen
:
1
2
Press
/
>
Q WT Service
>
Send Contact.
Find it:
/
>
>
Q WT Service
>
Configure
>
WT My Info
Auto Send On or Off
>
Enter the walkie-talkie ID number of the
person you want to send the contact
information to, or press
Select On to automatically send your
information, or Off to turn off automatic
sending.
K
under Browse
.
3
Select from Recent Calls
,
Contacts, or Memo
.
main attractions
40
4
Select the contact information you want
to send and push the WT button.
one touch WT
Find it:
/
>
Q WT Service
>
Configure
>
One Touch WT
turn WT Features on and off
One Touch WT sets your phone to do any of the
following each time you press the WT button
from the home screen:
You can turn on or turn off your phone’s ability
to send and receive messages, pictures, and
datebook events.
You cannot turn off your phone’s ability to
send and receive My Info and contact
information.
option
Off: Nothing happens when you press the
WT button from the home screen.
Find it:
/
>
Q WT Service
Select On/Off WT
Check or uncheck Messages
Events
>
Configure
Last Call: Call the most recent walkie-talkie ID
on the recent calls list.
1
2
.
Assigned No.: Call a walkie-talkie ID you assign.
Enter the number using your keypad, or
,
Pictures and/or
.
press
K
under Search. Select Contacts
,
Recent Calls, or Memo
.
WT Service: Go to WT Service. See “WT
service” on page 42.
Send Message: Go to the first screen to send a
message.
main attractions
41
Find it:
To send an item through a walkie-talkie call,
select Send Picture Send My Info, or
Send Contact. Choosing the WT item you want to
button to send it.
/
>
Q WT Service
option
Send Picture: Go to the first screen to send
pictures. See “send pictures” on page 37.
,
Send Event,
Send Event: Go the first screen to send a
datebook event.
Send My Info: Go to the first screen to send
My Info. See “send my info” on page 39.
Select Configure to set up the WT My Info
,
One Touch WT, and On/Off WT Features
.
Send Contact: Go to the first screen to send a
contact. See “send contact information” on
page 40.
Bluetooth® wireless
Find it:
/
>
r Bluetooth
WT service
The WT Service lets you quickly access WT
features and other walkie-talkie call features
from the main menu.
turn Bluetooth on or off
You can turn your phone’s Bluetooth feature
on or off. While Bluetooth power is on, your
phone can communicate with other devices.
You can also access the quick WT feature and
set the one touch WT feature.
Find it:
/
>
r Bluetooth
>
Setup
>
Power
>
On or Off
1
Select On to turn on Bluetooth power.
main attractions
42
2
3
Select Name if you wish to assign a name
to your phone.
2
Once your Bluetooth headset is set to be
found, select [Find Devices]. Your phone will
scan for all Bluetooth devices in range.
Select your Bluetooth headset from the
Select Find Me Time to determine the
amount of time in which your phone can
be found by other Bluetooth devices.
list of devices and press
r.
3
Your phone requires that you pair it with
the Bluetooth headset in order to create a
You can turn off Bluetooth if you want to
prolong battery life or if you enter an area
where Bluetooth use is prohibited.
connection. Press
K
under Yes when you
are prompted to pair with the headset.
make a Bluetooth connection
4
Enter the Bluetooth pass key.
Some Bluetooth devices ship with
Bluetooth PINs. Please refer to your
Bluetooth device’s user guide to locate
this information.
connect your phone with a Bluetooth
headset
Find it:
/
>
r Bluetooth
>
Hands Free
Note: Using a mobile device or accessory
while driving may cause distraction and may
be illegal. Always obey the laws and drive
safely.
If a device ships without a Bluetooth PIN,
then you can enter any PIN for that
device.
This phone offers the Bluetooth auto pair
feature with auto pair compatible
Motorola devices. When paired via
1
Follow the instructions on your Bluetooth
headset to set it up to be found.
main attractions
43
Bluetooth with a certain device, the PIN
will not be required.
use Bluetooth during a call
You can connect with available Bluetooth
devices during a call.
5
Press
K
under Ok.
Note: Once your phone and headset have
been paired, it will be stored on your phone
and you will not need to pair them again
unless the device is removed from memory.
1
2
While in a call, press
Select the audio device you want to
connect to from the list of Hands Free Devices
/
>
Use Bluetooth.
.
If the Audio Devices list contains only one device,
your phone will try to connect to it.
connect your phone with another
Bluetooth device
Find it:
/
>
r Bluetooth
>
Link to Devices
send information via Bluetooth
1
Select the device you want from the list of
found devices on your screen.
Your phone can transfer contact entries,
datebook events, audio files, and pictures to
another Bluetooth device.
2
Create a bond if you are prompted to
do so.
The receiving device must be within 32 feet
(10 meters) of your phone in order to connect.
If you have previously connected to a device,
the device will be stored on your phone so
you can connect with it easily.
Note: Files sent or received may be up
to 1 MB file size, depending on your
service provider.
main attractions
44
1
From the contact list, datebook, or media
center, select the contact entry, datebook
event, audio file, or picture you want to
send.
2
3
Press
/
>
Send Via...
>
Bluetooth.
Select the device you want to transfer the
information to, or search for the device by
selecting [Find Devices]
.
4
If prompted, bond with the device.
Your phone connects with the device and
transfers the information.
main attractions
45
call features
•
datebook events received
turn off a call alert
You can press the volume keys to turn off a
call alert before answering the call.
Find it:
/
>
c Recent Calls
Shortcut: From the home screen, press
to open the recent calls list.
`
The recent calls list displays up to 20 of your
most recent calls and call alerts. To view more
details for a call or call alert, highlight it and
recent calls
The recent calls list contains information
associated with calls you have made and
received, and call alerts you have received.
press
r.
store an item to contacts from
recent calls
Phone calls, walkie-talkie calls, My Info,
contacts, or location entries received from
other phones can be stored to the contact list
from the recent calls list.
When you send or receive walkie-talkie calls,
the recent call list contains the following WT
items with those calls:
•
•
•
•
contact information received
My Info received
short text messages received
pictures sent or received
call features
46
Find it:
/
>
c Recent Calls
caller ID
Caller ID helps you identify a caller before
answering the phone, by displaying the
number of the incoming call.
1
Highlight or select the item you want to
store.
2
Press
K
under Save to store the
information as a new entry in the contacts
list.
To block your phone number from being
displayed for the next outgoing call:
or
1
2
3
Press * 6 7
Enter the number you want to call.
Press
.
Select an existing contact and update the
information.
`
.
3
Press
changes.
K
under Done to save your
To permanently block your number, call your
customer service provider.
redial
To redial your last outgoing call, press and
hold
`
.
To redial your last walkie-talkie call, you must
set the one touch WT feature to Last Call (see
page 41).
call features
47
•
•
•
If Busy: When your phone is on a call or
transferring data.
call forward
Call forwarding sends calls to the phone
numbers you specify. You can forward all calls
to one number or forward missed calls to
different numbers depending on the reason
you missed the call. You can forward phone
lines 1 and 2 independently.
If No Answer: When you do not answer on
the first four rings.
If Unreachable: When your phone is out of
coverage or powered off.
Note: See your service plan for call
forwarding rates. Additional charges may
apply.
Find it:
/
>
d Call Forward
To for ward all calls:
1
2
Select Forward
Select To, enter the forwarding number
and press
>
All Calls.
voice names
You can place calls by speaking commands to
your phone, if you have previously assigned a
voice name to your contacts.
r
.
To set different forwarding numbers for
different types of missed calls:
assign voice names to contacts
1
2
Select Forward
>
Detailed.
1
Press
[New Contact]
K
under Contcs and select
.
Enter forwarding numbers for the
following options:
call features
48
2
3
4
Assign a name, phone number and select
sometimes an emergency call cannot be
placed due to network, environmental, or
interference issues.
[Options]
.
Select Voice Name and follow the prompt to
record the voice name.
Dial 911 or your local emergency number to
be connected to an emergency response
center. If you are on an active call, you must
end it before making an emergency call.
Press
K
under Back and
K
under Save.
place a call using a voice name
Press and hold the speaker key until you
are prompted to say the voice name. Speak
the voice name, and your phone will
automatically place the call.
)
Note: Your mobile device can use GPS and
AGPS signals to help emergency services find
you. See “GPS & AGPS” on page 59.
Note: Emergency calls cannot be placed
while the keypad is locked, or if your phone is
displaying a No Service message in the home
emergency calls
screen. To unlock the keypad, press
/
>
*.
Your service provider programs one or more
emergency phone numbers (such as 911) that
you can call under any circumstances, even
when your phone is locked or the SIM card is
not inserted. Emergency numbers vary by
country. Your pre-programmed emergency
number(s) may not work in all locations, and
Important: Always report your location to the
911 operator when placing an emergency call.
Some designated emergency call takers,
known as Public Safety Answering Points
(PSAPs), may not be equipped to receive GPS
location information from your phone.
call features
49
to the contact, press Edit, go to the phone
international calls
Your phone supports international dialing.
number and select [Options]
>
Speed #.
turbo dial
Press and hold
0
to insert your local
international access code (indicated by +).
Then, press the keypad keys to dial the
country code and phone number.
The first nine entries in your contact list are
set for turbo dial. They can be called by
pressing and holding the single-digit speed
dial number (1 through 9).
speed dial
Each phone number stored in your contact list
is assigned a speed dial number, which you
can use to call that number.
voicemail
All unanswered calls to your phone are
automatically transferred to your voicemail,
even if your phone is in use or turned off. It is
recommended that you set up your voicemail
and personal greeting as soon as your phone
is activated.
1
From the home screen, use the keypad to
enter the speed dial number assigned to
the phone number you want to call.
2
3
Press
Press
#.
`
.
set up your voicemail
To view or change the speed dial number for
a phone number, press e Contacts , scroll
To set up your voicemail, call your
Boost Mobile® number from either a landline
/
>
call features
50
phone or your handset. (If calling from a
landline phone, use your 7-digit phone
number as the passcode. If calling from your
handset, you will not be prompted for a
passcode.) Follow the steps to record your
name, a greeting, and a new voicemail
passcode.
To dismiss the voicemail message
notification, press or Back
r
.
Note: It is strongly recommended that you
create a passcode when setting up your
voicemail to protect against unauthorized
access. Without a passcode, anyone who has
access to your phone is able to access your
voicemail messages.
receiving a message
When you receive a voicemail message, your
phone shows New VoiceMail Message, and the
voicemail message indicator
top of the home screen.
3
appears at the
To listen to the voicemail message, press
under Call
K
.
call features
51
customize
Note: The silent indicator
of the home screen when you set your phone
to Silent. The vibrate indicator shows when
you set the phone to Vibrate All
,
shows at the top
ringtones
You can change the ringtones your phone
uses to notify you of incoming calls and other
events.
5
.
set your phone to vibrate
Find it:
/
>
T Ring Tones
Set your phone to vibrate for all calls and
alerts.
1
2
Set Vibrate All to Off
.
Scroll through the list of ringtones and
select the one you want to assign. Vibrate
sets your phone to vibrate instead of
making a sound. Silent sets your phone to
neither vibrate nor make a sound.
Find it:
/
>
T Ring Tones
>
Vibrate All
>
On or Locked
•
The On option lets you turn off Vibrate All
by pressing the up volume key.
3
Select the feature(s) you want to assign
the ringtone to.
•
The Locked option requires you to press
and hold the up volume key to turn of
Vibrate All. This option helps prevent you
4
When you are finished, press
under Done
K
from accidentally turning of Vibrate All
.
.
customize
52
To set Vibrate All to On or Locked using the volume
keys:
backlight
Set the amount of time that the display and
Java™ apps backlights remain on, or turn off
the backlight feature to extend battery life.
Press the down volume key multiple times to
turn off the volume and set Vibrate All to On
Then press and hold the down volume key to
set Vibrate All to Locked
.
Find it:
/
>
R Settings
>
Display/Info
>
Backlight
.
To set your phone to vibrate instead of making
a sound for some features but not others:
wallpaper
Find it:
/
>
T Ring Tones
Set a previously saved photo or picture as a
wallpaper (background) image on your phone’s
display screen or throughout all menu
screens.
1
2
3
Set Vibrate All to Off
.
Select Vibrate from the list of ringtones.
Select the feature(s) you want to set to
vibrate.
Find it:
/
>
R Settings
Select Wallpaper
Scroll through the list of pictures and
press to select a picture.
>
Display/Info
>
Wallpaper
1
2
.
4
When you are finished, press
under Done
K
.
r
You can set the wallpapers to change
automatically after a certain period of time by
turning on the Auto Cycle feature located in the
customize
53
wallpaper menu. You can select from 5 minutes
Daily, or Startup
,
set your privacy options
Find it: Privacy
15 minutes
,
1 hour
,
8 hours
,
.
/
>
i GPS
>
Select from the following options:
hide or show
location
Your phone has a location feature for use in
connection with location-based services that
may be available in the future.
option
Restricted
No Java™ apps or similar
software applications may
view the location of your
phone. However, location
information may still be
available to the phone’s owner,
fleet manager, or account
administrator.
Allowing the network to detect your position
using GPS technology can make some
applications and services easier to use.
Restricting access to your position
information disables the GPS location function
for all purposes except 911, but will not hide
your general location based on the cell site
serving your call. No application or service
may use your location without your request or
permission. GPS-enhanced 911 is not
available in all areas.
Unrestricted
All applications may view the
location of your phone,
without notifying you.
customize
54
option
Ask Access
When an application attempts
to view the location of your
phone, you will be prompted
to give permission. However,
location information may still
be available to the phone’s
owner, fleet manager, or
account administrator.
change GPS PIN
When you receive your phone, your GPS PIN
is set to 0000. To change your GPS PIN:
Find it:
/
>
R Settings
>
Security
>
Change Passwords
>
GPS PIN
1
Enter the current GPS PIN when
prompted, then enter the new
four-to-eight digit GPS PIN.
2
Re-enter the new GPS PIN to confirm.
customize
55
Safety, Regulatory & Legal
•
•
Do not dry a wet or damp battery with an appliance or
Battery Use & Safety
heat source, such as a hair dryer or microwave oven.
Battery Use & Safety
Important: Handle and store batteries properly to avoid
Avoid leaving your phone in your car in high
temperatures.*
injury or damage. Most battery issues arise from improper
handling of batteries, and particularly from the continued use of
damaged batteries.
DOs
•
Do avoid dropping the battery or phone. Dropping
these items, especially on a hard surface, can potentially
cause damage.*
DON’Ts
•
Don’t disassemble, crush, puncture, shred, or otherwise
attempt to change the form of your battery.
•
Do contact your service provider or Motorola if your phone
or battery has been damaged from dropping or high
temperatures.
•
Don’t let the phone or battery come in contact with
water. Water can get into the phone’s circuits, leading to
corrosion. If the phone and/or battery get wet, have them
checked by your service provider or contact Motorola,
even if they appear to be working properly.*
* Note: If the product guide expressly states that your phone is
designed to resist damage from exposure to certain rugged
conditions, such as water immersion, rain, dust, high and low
temperatures, shock, or other conditions, do not exceed the stated
limits, and ensure the stated precautions are taken. Always make
sure that the battery compartment is closed and secure to avoid
direct exposure of the battery to any of these conditions.
•
•
Don’t allow the battery to touch metal objects. If
metal objects, such as jewelry, stay in prolonged contact
with the battery contact points, the battery could become
very hot.
Don’t place your battery near a heat source.
Excessive heat can damage the phone or the battery. High
temperatures can cause the battery to swell, leak, or
malfunction. Therefore:
Important: Use Motorola Original products for quality
assurance and safeguards. To aid consumers in identifying
authentic Motorola batteries from non-original or counterfeit
batteries (that may not have adequate safety protection), Motorola
Safety, Regulatory & Legal
56
provides holograms on its batteries. Consumers should confirm
that any battery they purchase has a “Motorola Original”
hologram.
Proper and safe battery disposal and recycling: Proper
battery disposal is not only important for safety, it benefits the
environment. Consumers may recycle their used batteries in many
retail or service provider locations. Additional information on
proper disposal and recycling may be found on the Web:
Motorola recommends you always use Motorola-branded
batteries and chargers. Motorola mobile devices are designed
to work with Motorola batteries. If you see a message on your
display such as Invalid Battery or Unable to Charge, take the following
steps:
•
•
Disposal: Promptly dispose of used batteries in
accordance with local regulations. Contact your local
recycling center or national recycling organizations for
more information on how to dispose of batteries.
032375o
•
•
•
•
Remove the battery and inspect it to confirm that it has a
“Motorola Original” hologram;
If there is no hologram, the battery is not a Motorola
battery;
Warning: Never dispose of batteries in a fire because they may
explode.
If there is a hologram, replace the battery and retry
charging it;
If the message remains, contact a Motorola authorized
service center.
Battery Charging
Battery Charging
Notes for charging your phone’s battery:
Important: Motorola’s warranty does not cover damage to the
phone caused by non-Motorola batteries and/or chargers.
•
When charging your battery, keep it near room
temperature. Never expose batteries to temperatures
below 0°C (32°F) or above 45°C (113°F) when charging.
Warning: Use of a non-Motorola battery or charger may present a
risk of fire, explosion, leakage, or other hazard.
•
•
New batteries are not fully charged.
New batteries or batteries stored for a long time may take
more time to charge.
•
Motorola batteries and charging systems have circuitry
that protects the battery from damage from overcharging.
Safety, Regulatory & Legal
57
general, the closer you are to a wireless base station, the lower
the power output.
Specific Absorption Rate (IEEE)
SAR (IEEE)
Your model wireless phone meets the governmental
Before a mobile device is available for sale to the public in the U.S.
and Canada, it must be tested and certified to the FCC and Industry
Canada that it does not exceed the limit established by each
government for safe exposure. The tests are performed in
positions and locations (e.g., at the ear and worn on the body)
submitted to the FCC and available for review by Industry Canada.
The highest SAR value for this mobile device when tested for use
at the ear is 1.43 W/kg, and when worn on the body, as described
in this guide, is 1.28 W/kg. Body-worn measurements can differ,
depending upon available accessories and regulatory
requirements for exposure to radio waves.
Your mobile device is a radio transmitter and receiver. It is
designed and manufactured to not exceed limits for exposure to
radio frequency (RF) energy set by the Federal Communications
Commission (FCC) of the U.S. Government and by the Canadian
regulatory authorities. These limits are part of comprehensive
guidelines and establish permitted levels of RF energy for the
general population. The guidelines are based on standards that
were developed by independent scientific organizations through
periodic and thorough evaluation of scientific studies. The
standards include a substantial safety margin designed for the
safety of all persons, regardless of age or health, and to account
for any variations in measurements.
requirements. The SAR information includes the Motorola testing
protocol, assessment procedure, and measurement uncertainty
range for this product.
While there may be differences between the SAR levels of various
mobile devices and at various positions, they meet the
governmental requirements for safe exposure. Please note that
improvements to this product model could cause differences in the
SAR value for later products; in all cases, products are designed to
be within the guidelines.
The exposure standard for mobile devices employs a unit of
measurement known as the Specific Absorption Rate (SAR). The
IEEE SAR limit set by the FCC and by the Canadian regulatory
authorities is 1.6 watts per kilogram (W/kg), averaged over one
gram of tissue. Tests for SAR are conducted using procedures
accepted by the FCC and by Industry Canada with the mobile
device transmitting at its highest certified power level in all tested
frequencies. Although the SAR is determined at the highest
certified power level, the actual SAR level of the mobile device
while operating can be below the maximum value. This is because
the mobile device is designed to operate at multiple power levels
so as to use only the power required to reach the network. In
Additional information on SAR can be found on the Cellular
Telecommunications & Internet Association (CTIA) Web site:
or the Canadian Wireless Telecommunications Association (CWTA)
Web site:
Safety, Regulatory & Legal
58
Software Copyright Notice
GPS & AGPS
Software Copyright Notice
GPS & AGPS
Motorola products may include copyrighted Motorola and
Your mobile device can use Global Positioning System (GPS)
third-party software stored in semiconductor memories or other
media. Laws in the United States and other countries preserve for
Motorola and third-party software providers certain exclusive
rights for copyrighted software, such as the exclusive rights to
distribute or reproduce the copyrighted software. Accordingly, any
copyrighted software contained in Motorola products may not be
modified, reverse-engineered, distributed, or reproduced in any
manner to the extent allowed by law. Furthermore, the purchase of
Motorola products shall not be deemed to grant either directly or
by implication, estoppel, or otherwise, any license under the
copyrights, patents, or patent applications of Motorola or any
third-party software provider, except for the normal, non-exclusive,
royalty-free license to use that arises by operation of law in the
sale of a product.
signals for location-based applications. GPS uses satellites
controlled by the U.S. government that are subject to changes
implemented in accordance with the Department of Defense policy
and the Federal Radio Navigation Plan. These changes may affect
the performance of location technology on your mobile device.
Your mobile device can also use Assisted Global Positioning
System (AGPS), which obtains information from the cellular
network to improve GPS performance. AGPS uses your wireless
service provider's network and therefore airtime, data charges,
and/or additional charges may apply in accordance with your
service plan. Contact your wireless service provider for details.
Your Location
Location-based information includes information that can be used
to determine the approximate location of a mobile device. Mobile
phones which are connected to a wireless network transmit
location-based information. Devices enabled with GPS or AGPS
technology also transmit location-based information. Additionally,
if you use applications that require location-based information
(e.g. driving directions), such applications transmit location-based
information. This location-based information may be shared with
third parties, including your wireless service provider, applications
providers, Motorola, and other third parties providing services.
Content Copyright
Content Copyright
The unauthorized copying of copyrighted materials is contrary to
the provisions of the Copyright Laws of the United States and
other countries. This device is intended solely for copying
non-copyrighted materials, materials in which you own the
copyright, or materials which you are authorized or legally
permitted to copy. If you are uncertain about your right to copy any
material, please contact your legal advisor.
Safety, Regulatory & Legal
59
Therefore, you should visually confirm that the navigational
instructions are consistent with what you see. All drivers should
pay attention to road conditions, closures, traffic, and all other
factors that may impact driving. Always obey posted road signs.
Emergency Calls
When you make an emergency call, the cellular network may
activate the AGPS technology in your mobile device to tell the
emergency responders your approximate location.
AGPS has limitations and might not work in your area
Therefore:
.
Safety and General Information
This section contains important information on the safe and
efficient operation of your mobile device. Read this
information before using your integrated multi-service
portable radio.
•
•
Always tell the emergency responder your location to the
best of your ability; and
Remain on the phone for as long as the emergency
responder instructs you.
Performance Tips
Exposure to Radio Frequency (RF) Energy
•
Go outside and away from underground locations, covered
Your mobile device contains a transmitter and receiver. When it is
ON, it receives and transmits RF energy. When you communicate
with your mobile device, the system handling your call controls the
power level at which your mobile device transmits.
vehicles, structures with metal or concrete roofs, tall
buildings, and foliage. Indoor performance might improve
if you move closer to windows, but some window sun
shielding films can block satellite signals.
Your mobile device is designed to comply with local regulatory
requirements in your country concerning exposure of human beings
to RF energy.
•
Move away from radios, entertainment equipment, and
other electronic devices.
Portable Radio Product Operation and EME
Exposure
Your Motorola radio product is designed to comply with the
following national and international standards and guidelines
regarding exposure of human beings to radio frequency
electromagnetic energy (EME):
Navigation
Navigation
Motorola strives to provide complete and accurate mapping
information, directions, and other navigational data, using a
combination of governmental and private location information
sources. These sources may contain inaccurate or incomplete data.
In some countries, complete information may not be available.
Safety, Regulatory & Legal
60
•
•
•
•
•
United States Federal Communications Commission, Code
of Federal Regulations; 47 CFR part 2 sub-part J.
Product Operation
When placing or receiving a phone call, hold your mobile device
just like you would a landline phone. Speak directly into the
American National Standards Institute (ANSI) / Institute of
Electrical and Electronics Engineers (IEEE). C95. 1-1992.
microphone
.
Two-way radio operation
Institute of Electrical and Electronics Engineers (IEEE).
C95. 1-2005 Edition.
Your radio product has been designed and tested to comply with
national and international standards and guidelines regarding
human exposure to RF electromagnetic energy, when operated in
the two-way mode (at the face, or at the abdomen when using an
audio accessory) at usage factors of up to 50% talk/50% listen.
International Commission on Non-Ionizing Radiation
Protection (ICNIRP) 1998.
Ministry of Health (Canada). Safety Code 6. Limits of
Human Exposure to Radio frequency Electromagnetic
Fields in the Frequency Range from 3 kHz to 300 GHz,
1999.
Transmit no more than the rated duty factor of 50% of the time. To
transmit (talk), push the PTT button. To receive calls, release the
PTT button. Transmitting 50% of the time or less, is important
because this radio generates measurable RF energy only when
transmitting (in terms of measuring for standards compliance).
•
•
Australian Communications Authority Radio
communications (Electromagnetic Radiation - Human
Exposure) Standard 2003.
When using your radio product as a traditional
two-way radio, hold the radio product in a
vertical position with the microphone one
to two inches (2.5 to 5 cm) away from the
ANATEL, Brazil Regulatory Authority, Resolution 303 (July
2, 2002) “Regulation of the limitation of exposure to
electrical, magnetic, and electromagnetic fields in the
radio frequency range between 9 kHz and 300 GHz.”
“Attachment to Resolution 303 from July 2, 2002.”
lips
.
If you wear the mobile device on your body,
always place the mobile device in a Motorola approved clip,
holder, holster, case or body harness. If you do not use a body-worn
accessory supplied or approved by Motorola and are not using the
mobile device in the intended use positions along side the head in
the phone mode or in front of the face in the two-way radio mode,
or if you hang your device from a lanyard around your neck, keep
Operational Precautions
For optimal mobile device performance, and to be sure that human
exposure to RF energy does not exceed the guidelines set forth in
the relevant standards, always follow these instructions and
precautions.
Safety, Regulatory & Legal
61
the device at least 2.5 centimeters (1 inch) from your body when
transmitting.
•
ALWAYS keep the mobile device more than
20 centimeters (8 inches) from the implantable medical
device when the mobile device is turned ON.
Approved Accessories
For a list of approved Motorola accessories call 1-800-453-0920, or
•
•
DO NOT carry the mobile device in the breast pocket;
Use the ear opposite the implantable medical device to
minimize the potential for interference.
RF Energy Interference/Compatibility
•
Turn OFF the mobile device immediately if you have any
reason to suspect that interference is taking place.
Nearly every electronic device is subject to RF energy interference
from external sources if inadequately shielded, designed, or
otherwise configured for RF energy compatibility. In some
circumstances, your mobile device may cause interference with
other devices.
Read and follow the directions from the manufacturer of your
implantable medical device. If you have any questions about using
your mobile device with your implantable medical device, consult
your health care provider.
Follow Instructions to Avoid Interference Problems
Turn OFF your mobile device in any location where posted notices
instruct you to do so.
Driving Precautions
Using a mobile device while driving may cause distraction. End a
call if you can’t concentrate on driving. Input information about
your destination and route prior to your drive. Do not input data or
engage in text messaging while driving. Keep your eyes on the
road while driving. Listen to the audible turn-by-turn directions, if
available.
In an aircraft, turn off your mobile device whenever instructed to
do so by airline staff. If your mobile device offers an airplane mode
or similar feature, consult airline staff about using it in flight.
Implantable Medical Devices
If you have an implantable medical devices, such as a pacemaker
or defibrillator, consult your physician before using this mobile
device.
Also, using a mobile device or accessory may be prohibited or
restricted in certain areas. Always obey the laws and regulations
on the use of these products.
Persons with implantable medical devices should observe the
following precautions:
Responsible driving practices can be found at
Safety, Regulatory & Legal
62
Operational Warnings
Obey all posted signs when using mobile devices in public areas.
Symbol
Definition
Do not throw your battery or mobile device in the
trash.
Potentially Explosive Atmospheres
Areas with potentially explosive atmospheres are often but not
always posted, and can include fueling areas such as below decks
on boats, fuel or chemical transfer or storage facilities, or areas
where the air contains chemicals or particles, such as grain, dust
or metal powders.
Do not let your battery, charger, or mobile device
get wet.
Listening at full volume to music or voice through
a headset may damage your hearing.
When you are in such area, turn off your mobile device, and do not
remove, install, or charge batteries. In such areas, sparks can
occur and cause an explosion or fire.
Batteries and Chargers
Symbol Key
Caution: Improper treatment or use of batteries may present a
danger of fire, explosion, leakage, or other hazard. For more
information, see “Battery Use & Safety.”
Your battery, charger, or mobile device may contain symbols,
defined as follows:
Symbol
Definition
Keep Your Mobile Device and Its Accessories
Away from Small Children
032374o
Important safety information follows.
These products are not toys and may be hazardous to small
Do not dispose of your battery or mobile device in
a fire.
children. For example:
•
•
A choking hazard may exist for small, detachable parts.
Improper use could result in loud sounds, possibly causing
hearing injury.
Your battery or mobile device may require
recycling in accordance with local laws. Contact
your local regulatory authorities for more
information.
032375o
•
Improperly handled batteries could overheat and cause
a burn.
Safety, Regulatory & Legal
63
time is required before your hearing could be affected. To protect
your hearing:
Glass Parts
a substantial impact. If glass breaks, do not touch or attempt to
remove. Stop using your mobile device until the glass is replaced
by a qualified service center.
•
•
•
Limit the amount of time you use headsets or headphones
at high volume.
Avoid turning up the volume to block out noisy
surroundings.
Turn the volume down if you can’t hear people speaking
near you.
Seizures/Blackouts
Some people may be susceptible to epileptic seizures or blackouts
when exposed to flashing lights, such as when playing video
games. These may occur even if a person has never had a previous
seizure or blackout.
If you experience hearing discomfort, including the sensation of
pressure or fullness in your ears, ringing in your ears, or muffled
speech, you should stop listening to the device through your
headset or headphones and have your hearing checked.
If you have experienced seizures or blackouts, or if you have a
family history of such occurrences, please consult with your
physician before playing video games or enabling a flashing-lights
feature (if available) on your mobile device.
For more information about hearing, see our Web site at
Repetitive Motion
Discontinue use and consult a physician if any of the following
symptoms occur: convulsion, eye or muscle twitching, loss of
awareness, involuntary movements, or disorientation. It is always
a good idea to hold the screen away from your eyes, leave the
lights on in the room, take a 15-minute break every hour, and stop
use if you are tired.
When you repetitively perform actions such as pressing keys or
entering finger-written characters, you may experience occasional
discomfort in your hands, arms, shoulders, neck, or other parts of
your body. If you continue to have discomfort during or after such
use, stop use and see a physician.
Caution About High Volume Usage
Warning: Warning: Exposure to loud noise from any
source for extended periods of time may affect your
hearing. The louder the volume sound level, the less
Safety, Regulatory & Legal
64
Use & Care
Motorola Limited Warranty for the
United States and Canada
Use & Care
To care for your Motorola phone, please keep it away from:
liquids of any kind
What Does this Warranty Cover?
Note: FOR IDEN SUBSCRIBER PRODUCTS, ACCESSORIES
AND SOFTWARE PURCHASED IN THE UNITED STATES OR
CANADA
Don’t expose your phone to water, rain, extreme
humidity, sweat, or other moisture. If it does get wet,
don’t try to accelerate drying with the use of an oven or
dryer, as this may damage the phone.
Subject to the exclusions contained below, Motorola, Inc. warrants
its Motorola iDEN Digital Mobile and Portable Handsets
("Products"), Motorola-branded or certified accessories sold for
use with these Products ("Accessories") and Motorola software
contained on CD-Roms or other tangible media and sold for use
with these Products ("Software") to be free from defects in
materials and workmanship under normal consumer usage for the
period(s) outlined below. This limited warranty is a
consumer's exclusive remedy, and applies as follows to
new Products, Accessories and Software purchased by
consumers in the United States or Canada, which are
accompanied by this written warranty:
extreme heat or cold
Avoid temperatures below 0°C/32°F or
above 45°C/113°F.
microwaves
Don’t try to dry your phone in a microwave oven.
dust and dirt
Don’t expose your phone to dust, dirt, sand, food, or
other inappropriate materials.
cleaning solutions
Products Covered
Length of Coverage
To clean your phone, use only a dry soft cloth. Don’t use
alcohol or other cleaning solutions.
Products as defined
above.
Ninety (90) days from the date of
purchase by the first consumer
purchaser of the product.
shock and vibration
Don’t drop your phone.
Safety, Regulatory & Legal
65
Batteries. Only batteries whose fully charged capacity falls below
80% of their rated capacity and batteries that leak are covered by
this limited warranty.
Products Covered
Length of Coverage
Accessories as
defined above.
Ninety (90) days from the date of
purchase by the first consumer
purchaser of the product.
Abuse & Misuse. Defects or damage that result from: (a)
improper operation, storage, misuse or abuse, accident or neglect,
such as physical damage (cracks, scratches, etc.) to the surface of
the product resulting from misuse; (b) contact with liquid, water,
rain, extreme humidity or heavy perspiration, sand, dirt or the like,
extreme heat, or food; (c) use of the Products or Accessories for
commercial purposes or subjecting the Product or Accessory to
abnormal usage or conditions; or (d) other acts which are not the
fault of Motorola, are excluded from coverage.
Products or
The balance of the original
warranty or for ninety (90) days
from the date returned to the
consumer, whichever is longer.
Accessories that are
Repaired or
Replaced.
Software as defined
above. Applies only to
physical defects in the
media that embodies
the copy of the software
(e.g. CD-ROM, or
Ninety (90) days from the date of
purchase
.
Use of Non-Motorola Products and Accessories. Defects or
damage that result from the use of Non-Motorola branded or
certified Products, Accessories, Software or other peripheral
equipment are excluded from coverage.
floppy disk).
Unauthorized Service or Modification. Defects or damages
resulting from service, testing, adjustment, installation,
maintenance, alteration, including without limitation, software
changes, or modification in any way by someone other than
Motorola, or its authorized service centers, are excluded from
coverage.
What is not covered? (Exclusions)
Normal Wear and Tear. Periodic maintenance, repair and
replacement of parts due to normal wear and tear are excluded
from coverage.
Ornamental Decorations. Ornamental decorations such as
emblems, graphics, rhinestones, jewels, gemstones and their
settings, and other decorative elements, are excluded from
coverage.
Altered Products. Products or Accessories with (a) serial
numbers or date tags that have been removed, altered or
obliterated; (b) broken seals or that show evidence of tampering;
(c) mismatched board serial numbers; or (d) nonconforming or
Safety, Regulatory & Legal
66
non-Motorola housings, antennas, or parts, are excluded from
coverage.
personal contacts, games and ringer tones, will be reinstalled. To
avoid losing such data, software and applications please create a
back up prior to requesting service.
Communication Services. Defects, damages, or the failure of
Products, Accessories or Software due to any communication
service or signal you may subscribe to or use with the Products,
Accessories or Software is excluded from coverage.
How to Obtain Warranty Service or Other
Information
To obtain service or information, please call:
Software Embodied in Physical Media. No warranty is made
that the software will meet your requirements or will work in
combination with any hardware or software applications provided
by third parties, that the operation of the software products will be
uninterrupted or error free, or that all defects in the software
products will be corrected.
Motorola iDEN Customer Services 1-800-453-0920 or
954-723-4910
TTY-877-483-2840
Software NOT Embodied in Physical Media. Software that is
not embodied in physical media (e.g. software that is downloaded
from the internet), is provided "as is" and without warranty.
You will receive instructions on how to ship the Products,
Accessories or Software, at your expense, to a Motorola
Authorized Repair Center. To obtain service, you must include: (a) a
copy of your receipt, bill of sale or other comparable proof of
purchase; (b) a written description of the problem; (c) the name of
your service provider, if applicable; (d) the name and location of the
installation facility (if applicable) and, most importantly; (e) your
address and telephone number.
Who is covered?
This warranty extends only to the first consumer purchaser, and is
not transferable.
What will Motorola Do?
What Other Limitations Are There?
Motorola, at its option, will at no charge repair, replace or refund
the purchase price of any Products, Accessories or Software that
does not conform to this warranty. We may use functionally
equivalent reconditioned/refurbished/pre-owned or new Products,
Accessories or parts. No data, software or applications added to
your Product, Accessory or Software, including but not limited to
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE
DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE
REPAIR, REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS
Safety, Regulatory & Legal
67
EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF
THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OF IMPLIED. IN NO EVENT SHALL
MOTOROLA BE LIABLE, WHETHER IN CONTRACT OR TORT
(INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE
PURCHASE PRICE OF THE PRODUCT, ACCESSORY OR SOFTWARE,
OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF
REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF
INFORMATION OR DATA, SOFTWARE OR APPLICATIONS OR
OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION
WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS,
ACCESSORIES OR SOFTWARE TO THE FULL EXTENT THESE
DAMAGES MAY BE DISCLAIMED BY LAW.
exercise of the exclusive rights reserved for Motorola, is
permitted.
Patent and Software Provisions:
MOTOROLA will defend, at its own expense, any suit brought
against the end user purchaser to the extent that it is based on a
claim that the Product or parts infringe a patent, and Motorola will
pay those costs and damages finally awarded against the end user
purchaser in any such suit which are attributable to any such
claim, but such defense and payments are conditioned on the
following:
•
That MOTOROLA will be notified promptly in writing by
such purchaser of any notice of such claim;
•
That MOTOROLA will have sole control of the defense of
such suit and all negotiations for its settlement or
compromise; and
Some states and jurisdictions do not allow the limitation or
exclusion of incidental or consequential damages, or limitation on
the length of an implied warranty, so the above limitations or
exclusions may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights that vary from
state to state or from one jurisdiction to another.
•
Should the Product or parts become, or in MOTOROLA’S
opinion be likely to become, the subject of a claim of
infringement of a patent, that such purchaser will permit
MOTOROLA, at its option and expense, either to procure
for such purchaser the right to continue using the Product
or parts or to replace or modify the same so that it
becomes non infringing or to grant such purchaser a credit
for the Product or parts as depreciated and accept its
return. The depreciation will be an equal amount per year
over the lifetime of the Product or parts as established by
MOTOROLA.
Laws in the United States and other countries preserve for
Motorola certain exclusive rights for copyrighted Motorola
software such as the exclusive rights to reproduce and distribute
copies of the Motorola software. Motorola software may only be
copied into, used in, and redistributed with, the Products
associated with such Motorola software. No other use, including
without limitation disassembly of such Motorola software or
Safety, Regulatory & Legal
68
MOTOROLA will have no liability with respect to any claim of
patent infringement which is based upon the combination of the
Product or parts furnished hereunder with software, apparatus or
devices not furnished by MOTOROLA, nor will MOTOROLA have
any liability for the use of ancillary equipment or software not
furnished by MOTOROLA which is attached to or sued in
connection with the Product or any parts thereof. In no event shall
MOTOROLA be liable for any incidental, special or consequential
damages arising from any claim of patent infringement or alleged
infringement.
Hearing Aid Compatibility With Mobile
Phones
Some Motorola phones are measured for compatibility with
hearing aids. If the box for your particular model has “Rated for
Hearing Aids” printed on it, the following explanation applies.
When some mobile phones are used near some hearing devices
(hearing aids and cochlear implants), users may detect a buzzing,
humming, or whining noise. Some hearing devices are more
immune than others to this interference noise, and phones also
vary in the amount of interference they generate.
Laws in the United States and other countries preserve for
MOTOROLA certain exclusive rights for copyrighted MOTOROLA
software, such as the exclusive rights to reproduce in copies and
distribute copies of such MOTOROLA software. MOTOROLA
software may be used in only the Product in which the software
was originally embodied and such software in such Product may
not be replaced, copied, distributed, modified in any way, or used
to produce any derivative thereof. No other use including, without
limitation, alteration, modification, reproduction, distribution, or
reverse engineering of such MOTOROLA software or exercise or
rights in such MOTOROLA software is permitted. No license is
granted by implication, estoppel or otherwise under MOTOROLA
patent rights or copyrights.
The wireless telephone industry has developed ratings for some of
their mobile phones, to assist hearing device users in finding
phones that may be compatible with their hearing devices. Not all
phones have been rated. Phones that are rated have the rating on
their box or a label on the box. To maintain the published Hearing
Aid Compatibility (HAC) rating for this mobile phone, use only the
original equipment battery model.
The ratings are not guarantees. Results will vary depending on the
user’s hearing device and hearing loss. If your hearing device
happens to be vulnerable to interference, you may not be able to
use a rated phone successfully. Trying out the phone with your
hearing device is the best way to evaluate it for your personal
needs.
M-Ratings: Phones rated M3 or M4 meet FCC requirements and
are likely to generate less interference to hearing devices than
Safety, Regulatory & Legal
69
phones that are not labeled. M4 is the better/higher of the two
ratings.
Product Registration
Online Product Registration:
T-Ratings: Phones rated T3 or T4 meet FCC requirements and are
likely to be more usable with a hearing device’s telecoil (“T
Switch” or “Telephone Switch”) than unrated phones. T4 is the
better/higher of the two ratings. (Note that not all hearing devices
have telecoils in them.)
Product registration is an important step toward enjoying your new
Motorola product. Registering permits us to contact you for
product or software updates and allows you to subscribe to
updates on new products or special promotions. Registration is not
required for warranty coverage.
Hearing devices may also be measured for immunity to this type of
interference. Your hearing device manufacturer or hearing health
professional may help you find results for your hearing device. The
more immune your hearing aid is, the less likely you are to
experience interference noise from mobile phones.
Please retain your original dated sales receipt for your records. For
warranty service of your Motorola Personal Communications
Product you will need to provide a copy of your dated sales receipt
to confirm warranty status.
Information From the World Health
Organization
Present scientific information does not indicate the need for any
special precautions for the use of mobile phones. If you are
concerned, you may want to limit your own or your children’s RF
exposure by limiting the length of calls or by using hands-free
devices to keep mobile phones away from your head and body.
Thank you for choosing a Motorola product.
Export Law Assurances
Export Law
This product is controlled under the export regulations of the
United States of America and Canada. The Governments of the
United States of America and Canada may restrict the exportation
or re-exportation of this product to certain destinations. For further
information contact the U.S. Department of Commerce or the
Canadian Department of Foreign Affairs and International Trade.
Source: WHO Fact Sheet 193
Safety, Regulatory & Legal
70
Caring for the Environment by
Recycling
California Perchlorate Label
Some mobile phones use an internal, permanent backup battery on
the printed circuit board that may contain very small amounts of
perchlorate. In such cases, California law requires the following
label:
Recycling Information
This symbol on a Motorola product means the product
should not be disposed of with household waste.
Perchlorate Material - special handling may apply. See
Disposal of your Mobile Device &
Accessories
Please do not dispose of mobile devices or electrical
accessories (such as chargers, headsets, or batteries)
with your household waste. Do not dispose of your
battery or mobile device in a fire. These items should be disposed
of in accordance with the national collection and recycling
schemes operated by your local or regional authority. Alternatively,
you may return unwanted mobile devices and electrical
accessories to any Motorola Approved Service Center in your
region. Details of Motorola approved national recycling schemes,
and further information on Motorola recycling activities can be
There is no special handling required by consumers.
Privacy and Data Security
Motorola understands that privacy and data security are important
to everyone. Because some features of your mobile device may
affect your privacy or data security, please follow these
recommendations to enhance protection of your information:
•
Monitor access—Keep your mobile device with you and
do not leave it where others may have unmonitored
access. Lock your device’s keypad where this feature is
available.
Disposal of your Mobile Device Packaging &
Product Guide
Product packaging and product guides should only be disposed of
in accordance with national collection and recycling requirements.
Please contact your regional authorities for more details.
•
Keep software up to date—If Motorola or a
software/application vendor releases a patch or software
fix for your mobile device that updates the device’s
security, install it as soon as possible.
Safety, Regulatory & Legal
71
•
Secure personal information—Your mobile device can
store personal information in various locations including
your SIM card, memory card, and phone memory. Be sure
to remove or clear all personal information before you
recycle, return, or give away your device. You can also
backup your personal data to transfer to a new device.
•
Other information your device may transmit—Your
device may also transmit testing and other diagnostic
(including location-based) information, and other
non-personal information to Motorola or other third-party
servers. This information is used to help improve products
and services offered by Motorola.
Note: For information on how to backup or wipe data from
If you have further questions regarding how the use of your mobile
device may impact your privacy or data security, please contact
Motorola at [email protected], or contact your service
provider.
•
•
Online accounts—Some mobile devices provide a
Motorola online account (such as MOTOBLUR). Go to your
account for information on how to manage the account,
and how to use security features such as remote wipe and
device location (where available).
Smart Practices While Driving
Drive Safe, Call Smart
Location-based information—Location-based
information includes information that can be used to
determine the approximate location of a mobile device.
Mobile phones which are connected to a wireless network
transmit location-based information. Devices enabled
with GPS or AGPS technology also transmit
location-based information. Additionally, if you use
applications that require location-based information (e.g.
driving directions), such applications transmit
location-based information. This location-based
information may be shared with third parties, including
your wireless service provider, applications providers,
Motorola, and other third parties providing services.
Check the laws and regulations on the use of mobile
devices and their accessories in the areas where you drive.
Always obey them. The use of these devices may be
prohibited or restricted in certain areas—for example
(in English only) for more information.
Your mobile device lets you communicate by voice and
data—almost anywhere, anytime, wherever wireless service is
available and safe conditions allow. When driving a car, driving is
your first responsibility. If you choose to use your mobile device
while driving, remember the following tips:
•
Get to know your Motorola mobile device and its
features such as speed dial and redial. If available,
Safety, Regulatory & Legal
72
these features help you to place your call without taking
your attention off the road.
•
Do not engage in stressful or emotional
conversations that may be distracting. Make people
you are talking with aware you are driving and suspend
conversations that can divert your attention away from the
road.
•
•
When available, use a handsfree
device. If possible, add an additional
layer of convenience to your mobile device
with one of the many Motorola Original
handsfree accessories available today.
•
•
Use your mobile device to call for help. Dial 911 or
other local emergency number in the case of fire, traffic
accident, or medical emergencies (wherever wireless
phone service is available).
Position your mobile device within easy reach. Be
able to access your mobile device without removing your
eyes from the road. If you receive an incoming call at an
inconvenient time, if possible, let your voicemail answer it
for you.
Use your mobile device to help others in
emergencies. If you see an auto accident, crime in
progress, or other serious emergency where lives are in
danger, call 911 or other local emergency number
(wherever wireless phone service is available), as you
would want others to do for you.
•
•
•
Let the person you are speaking with know you are
driving; if necessary, suspend the call in heavy
traffic or hazardous weather conditions. Rain, sleet,
snow, ice, and even heavy traffic can be hazardous.
•
Call roadside assistance or a special
non-emergency wireless assistance number when
necessary. If you see a broken-down vehicle posing no
serious hazard, a broken traffic signal, a minor traffic
accident where no one appears injured, or a vehicle you
know to be stolen, call roadside assistance or other
special non-emergency wireless number (wherever
wireless phone service is available).
Do not take notes or look up phone numbers while
driving. Jotting down a “to do” list or going through your
address book takes attention away from your primary
responsibility, driving safely.
Dial sensibly and assess the traffic; if possible,
place calls when your car is not moving or before
pulling into traffic. If you must make a call while
moving, dial only a few numbers, check the road and your
mirrors, then continue.
Safety, Regulatory & Legal
73
Service and Repairs
If you have questions or need assistance, we’re here to help.
number of customer care options. You can also contact the
Motorola Customer Support Center at 1 (800) 453-0920 (United
States), 1 (877) 483-2840 (TTY, TDD United States for hearing
impaired).
Safety, Regulatory & Legal
74
index
Bluetooth
connect 43
send information 44
turning on or off 42
contacts
create 15
edit/delete 16
A
active phone line 27
alert
set ringer ID 16
set 30, 52
turn off 30, 46
alpha method text entry 29
answer a call 12
audio formats 35
audio jack 1
C
D
call
datebook 24
answer 12
any key answer 13
end 12
dial a phone number 12
dialed calls 46
display 26
make 12
drafts 22
B
call forward 48
call waiting 12
caller ID 47
center key 1, 2, 7, 31
battery
charging 10
installation 9
battery charge indicator 11,
27
E
earpiece volume 30
emergency number 49
end a call 12
index
75
end key 1, 12
event reminders 24
M
P
phone number
store 15
your number 17
picture formats 36
power key 1, 2, 11
make a call 12
menu key 1, 2, 7
message indicator 27
message threads 22
messaging 17
G
Get Stuff 36
H
handsfree speaker 31
hearing aid 32
R
micro USB connector 1, 10
home screen 26
received calls 46
recent calls 46
redial 47
ring style indicator 27
ring style, setting 30
ringer volume 30
ringtones
off 52
setting 52
turn off 52
N
I
navigation key 1, 2, 7, 31
numeric text entry 28
image formats 36
international calls 50
O
L
OK key 1, 2, 7, 31
on/off key 1
one touch WT 41
location 54
low battery message 27
vibrate 52
index
76
cleanup 21
S
security 34
send key 1, 12
service and repairs 74
signal strength indicator 26
SIM card 8, 34
SIM PIN 34
soft keys 1, 26
speaker 27
walkie-talkie call
answer 14
creating 17
drafts 22
receiving 18
sending 17
sent messages 23, 24
threads 22
3-way calls 13
features 36
make 13
send call alert 14
walkie-talkie ID 13, 15
wallpaper 53
speaker key 1, 12
speed dial 50
store your number 17
symbol text entry 28
WHO information 70
word method text entry 28
WT button 1
V
voice names 48
voicemail 50
volume 30
WT service 42
volume keys 1
T
Y
talk key 1, 12
text entry 27
your phone number 17
index
77
index
78
|
