Mitsubishi MZ360217EX User Manual

(
(
)
MZ360216EX KDC333RCAM4  
)
MZ360217EX KDC4033AM4  
CD-RECEIVER  
INSTRUCTION MANUAL  
© B64-3677-00/00 (MW)  
Safety precautions  
About CD players/disc changers  
connected to this unit  
2WARNING  
To prevent injury or fire, take the  
following precautions:  
Kenwood disc changers/ CD players released in  
1998 or later can be connected to this unit.  
Refer to the catalog or consult your Kenwood  
dealer for connectable models of disc changers/  
CD players.  
• To prevent a short circuit, never put or leave any  
metallic objects (such as coins or metal tools)  
inside the unit.  
Note that any Kenwood disc changers/ CD players  
released in 1997 or earlier and disc changers made  
by other makers cannot be connected to this unit.  
Connecting unsupported disc changers/CD players  
to this unit may result in damage.  
Set the "O-N" Switch to the "N" position for the  
applicable Kenwood disc changers/ CD players.  
The functions you can use and the information  
that can be displayed may differ depending on the  
models being connected.  
• Mounting and wiring this product requires  
skills and experience. For safety’s sake, leave the  
mounting and wiring work to professionals.  
2CAUTION  
To prevent damage to the machine, take  
the following precautions:  
• Make sure to ground the unit to a negative 12V  
DC power supply.  
• Do not install the unit in a spot exposed to direct  
sunlight or excessive heat or humidity. Also avoid  
places with too much dust or the possibility of  
water splashing.  
You can damage both your unit and the CD changer if  
you connect them incorrectly.  
• Do not place the faceplate (and the faceplate  
case) in areas exposed to direct sunlight, excessive  
heat or humidity. Also avoid places with too much  
dust or the possibility of water splashing.  
• To prevent deterioration, do not touch the  
terminals of the unit or faceplate with your  
fingers.  
Lens Fogging  
When you turn on the car heater in cold weather,  
dew or condensation may form on the lens in the  
CD player of the unit. Called lens fogging, this  
condensation on the lens may not allow CDs to  
play. In such a situation, remove the disc and wait  
for the condensation to evaporate. If the unit still  
does not operate normally after a while, consult  
your Kenwood dealer.  
• Do not subject the faceplate to excessive shock,  
as it is a piece of precision equipment.  
• When replacing a fuse, only use a new fuse with  
the prescribed rating. Using a fuse with the wrong  
rating may cause your unit to malfunction.  
• Do not use your own screws. Use only the screws  
provided. If you use the wrong screws, you could  
damage the unit.  
Do Not Load 8 cm (3 in.) CDs in the CD  
slot  
If you try to load a 8 cm (3 in.) CD with its adapter  
into the unit, the adapter might separate from the  
CD and damage the unit.  
English  
|
3
Notes  
• If you experience problems during installation,  
consult your Kenwood dealer.  
About DAB Tuner control  
(KDC-MP4533/MP4033/MP4033S)  
• When you purchase optional accessories, check  
with your Kenwood dealer to make sure that they  
work with your model and in your area.  
Refer to A group on the Instruction manual of DAB  
Tuner KTC-9090DAB (optional accessory) for the  
control method of DAB Tuner function.  
However, the following control methods of the  
function for this unit may be differed from the  
Instruction manual; therefore, refer to the following  
supplemental instruction.  
<Auto Ensemble Memory Entry>  
1. Select the preset band for Auto Ensemble  
Memory Entry.  
• If the unit fails to operate properly, press the Reset  
button. The unit returns to factory settings when  
the Reset button is pressed.  
• Press the reset button if the disc auto changer fails  
to operate correctly. Normal operation should be  
restored.  
2. Press the [AME] button for at least 2 seconds.  
Open Auto Ensemble Memory Entry.  
After memory storage is finished, the number of  
the pre-set buttons and the ensemble label are  
displayed.  
<Searching by programme type and language>  
and <Languages to be displayed> in  
<Programme Type (PTY) Function>  
At the operation to press [DISP] button, use [AUTO]  
button instead.  
Reset button  
• The characters which can be displayed by this  
unit are A-Z 0-9 @ " ‘ ` % & * + – = , . / \ < > [ ] ( ) : ;  
^ - { } | ~ .  
<Automatic Switching DAB priority>  
• The illustrations of the display and the panel  
appearing in this manual are examples used to  
explain more clearly how the controls are used.  
Therefore, what appears on the display in the  
illustrations may differ from what appears on the  
display on the actual equipment, and some of the  
illustrations on the display may be inapplicable.  
This function cannot be used.  
The marking of products using lasers  
(Except for some areas)  
CLASS 1  
LASER PRODUCT  
Cleaning the Unit  
If the faceplate of this unit is stained, wipe it with a  
dry soft cloth such as a silicon cloth.  
The label is attached to the chassis/case and says  
that the component uses laser beams that have  
been classified as Class 1. This means that the unit  
is utilizing laser beams that are of a weaker class.  
There is no danger of hazardous radiation outside  
the unit.  
If the faceplate is stained badly, wipe the stain off  
with a cloth moistened with neutral cleaner, then  
wipe it again with a clean soft dry cloth.  
Applying spray cleaner directly to the unit may affect its  
mechanical parts. Wiping the faceplate with a hard cloth  
or using a volatile liquid such as thinner or alcohol may  
scratch the surface or erases characters.  
Cleaning the Faceplate Terminals  
If the terminals on the unit or faceplate get dirty,  
wipe them with a dry, soft cloth.  
|
4
English  
About CDs  
Handling CDs  
Removing CDs  
• Do not touch the recording surface of the CD.  
When removing CDs from this unit pull them out  
horizontally.  
CDs that cannot be used  
• CDs that are not round cannot be used.  
• CD-R and CD-RW are easier to damage than a  
normal music CD. Use a CD-R or a CD-RW after  
reading the caution items on the package etc.  
• Do not stick tape etc. on the CD, or use a CD with  
tape stuck on it.  
• CDs with coloring on the recording surface or CDs  
that are dirty cannot be used.  
• This unit can only play the CDs with  
When using a new CD  
If the CD center hole or outside rim has burrs,  
use the CD only after removing the burrs with a  
ballpoint pen, etc.  
.
This unit may not correctly play discs which do  
not have the mark.  
• You cannot play A CD-R or CD-RW that has not  
been finalized. (For the finalization process refer to  
your CD-R/CD-RW writing software, and your CD-  
R/CD-RW recorder instruction manual.)  
Burrs  
CD storage  
Burrs  
• Do not place CDs in direct sunlight (On the seat  
or dashboard etc.) or where the temperature is  
high.  
• Store CDs in their cases.  
CD accessories  
Do not use disc type accessories.  
CD cleaning  
Clean from the center of the disc and move  
outward.  
English  
|
5
About MP3 and WMA  
The playable MP3/WMA file (hereafter called  
Audio file) and the media format has the following  
limitation. The Audio file, which is not conforming  
to the specification, may not play normally, or the  
file and folder names may not display correctly.  
The maximum number of characters for  
display  
File/Folder name: 64 (Joliet: 32) characters  
MP3 ID3 Tag/ WMA Contents property: 30  
characters  
Playable Audio file  
MP3, WMA  
File/Folder name is the number of the characters  
including the extensions.  
MP3 ID3 Tag can only display the tag of Ver1.0/1.1.  
Attach the correct extension for the Audio file (MP3:  
".MP3", WMA: ".WMA")  
Do not attach the extensions to files other than the  
Audio file. If the extension is attached, the file, which is  
not the Audio file, will play and outputs a loud noise,  
causing damage to the speaker.  
The files with copy protection cannot be played.  
The settings of your encoding software and the  
environment in which it is used may now allow you  
to play or view specific audio files. For encoding  
specifications and instructions on how to set encoding  
software, browse through software help or check with  
the developers.  
Limitation of structure for the file and the  
folder  
• Maximum number of directory levels: 8  
• Maximum number of folders: 100  
• Maximum number of files per folder: 255  
Playing order of the Audio file  
The Audio file plays in the order which is written by  
writing software. You may be able to set the playing  
order by writing the play sequence numbers such  
as "01" to "99" at the beginning of the file name.  
Example  
Playable MP3 file  
0
¡
: Folder  
: Audio file  
CD  
(1)  
¡!  
• MPEG 1/2 Audio Layer 3 file  
• Transfer bit rate: 8-320 kbps  
• Sampling frequency  
: 8, 11.025, 12, 16, 22.05, 24, 32, 44.1, 48 kHz  
2
¡"  
3
Playable WMA file  
¡#  
¡$  
• The file in accordance with Windows Media Audio  
(Except for the file for Windows Media Player 9 or  
after which applies the new functions)  
4
• Transfer bit rate: 48-192 kbps  
¡%  
• Sampling frequency: 32, 44.1, 48 kHz  
• Playing order  
Playable media  
Playing order after ¡! play.  
• CD-ROM, CD-R, CD-RW  
¡", ¡#, ¡$, ¡%...  
• File search  
Forward file search during ¡# play.  
Push the Control knob towards [¢] ¡$  
CD-RW discs which are quick formatted by the writing  
software cannot be used.  
When recording to the maximum media capacity at  
once, the writing software is set to "Disc at once".  
• Folder search  
Forward folder search during ¡" play.  
Push the Control knob towards [FM] 3, 4...  
• Folder select  
Playable disc format  
• ISO 9660 Level 1/2  
When the selection is set to directory 4, and you  
want to skip to the folder 2 at the same level.  
Push the Control knob towards [4] 2  
• Joliet  
• Romeo  
• Long file name.  
When the selection is set to directory 3, moves  
the level up by folder select.  
Push the Control knob towards [AM] 2  
|
6
English  
General features  
Control knob  
Release button  
LOUD indicator  
Clock display  
ATT indicator  
Power  
Volume  
Turning ON the Power  
Press the [SRC] button.  
Increasing Volume  
Turn the [VOL] knob clockwise.  
Turning OFF the Power  
Press the [SRC] button for at least 1 second.  
Decreasing Volume  
Turn the [VOL] knob counterclockwise.  
Selecting the Source  
Attenuator  
Turning the volume down quickly.  
Press the [SRC] button.  
Press the [ATT] button.  
Each time you press the button, the Attenuator  
turns ON and OFF.  
When the Attenuator is ON, the "ATT" indicator  
blinks.  
Source required  
Tuner  
CD  
External disc* (Optional accessory)  
Auxiliary input* (Optional accessory)  
Standby (Illumination only mode)  
Display  
"TUNER"  
"CD"  
"CD CH"  
"AUX EXT"  
"STANDBY"  
* Function of the KDC-MP4533/MP4033/MP4033S.  
English  
|
7
General features  
System Q  
Selecting the best sound setting preset for  
different types of music.  
Adjustment Item Display  
Range  
–8 — +8  
–8 — +8  
–8 — +8  
Left 15 — Right 15  
Rear 15 — Front 15  
Bass level  
Middle level  
Treble level  
Balance  
"BAS L"  
"MID L"  
"TRE L"  
"BAL"  
1 Select the source to set  
Fader  
"FAD"  
Press the [SRC] button.  
Exit Audio Control mode (Volume control mode)  
2 Select the Sound type  
Press the [Q] button.  
5 Exit Audio Control mode  
Press any button.  
Press a button other than the [VOL] knob, [SRC],  
When you press the button once, the current  
sound setting is displayed.  
Each time you press the button, the sound  
setting alternates.  
[0] and [ATT] button.  
Sound setting  
Natural  
Rock  
Pops  
Easy  
Display  
"NATURAL"  
"ROCK"  
"POPS"  
"EASY"  
"TOP40"  
"JAZZ"  
Audio Setup  
Setting the Sound system, such as Volume offset  
and Loudness.  
Top 40  
Jazz  
1 Select the source to adjust  
Press the [SRC] button.  
2 Enter Audio Setup mode  
Change each setting value with the <Speaker  
Setting> (page 9).  
First, select the speaker type with the Speaker setting.  
When the value is set up by <Audio Control> (page 8),  
"USER" is displayed.  
Press the [VOL] knob for at least 1 second.  
3 Select the Audio Setup item to adjust  
Press the [VOL] knob.  
Each time you press the knob, the item to be  
adjusted alternates between the items shown in  
the table below.  
4 Adjust the Audio setup item  
Audio Control  
Turn the [VOL] knob.  
1 Select the source to adjust  
Adjustment Item Display  
Range  
–8 —  
ON/OFF  
Press the [SRC] button.  
Volume offset  
Loudness  
"V-OFF"  
"LOUD"  
0
2 Enter Audio Control mode  
Press the [VOL] knob.  
3 Select the Audio item to adjust  
Press the [VOL] knob.  
Each time you press the knob, the item to be  
adjusted alternates between the items shown in  
the table below.  
Volume offset: Sets each source’s volume as a  
difference from the basic volume.  
Loudness: Compensates for low and high tones  
during low volume.  
When Loudness is ON, "LOUD" indicator  
is ON.  
4 Adjust the Audio item  
5 Exit Audio Setup mode  
Turn the [VOL] knob.  
Press the [VOL] knob for at least 1 second.  
|
8
English  
In Audio file source  
Speaker Setting  
Information  
Display  
"TITLE"*  
"ALBUM"*  
"FOLDER"  
"FILE"  
Fine-tuning so that the System Q value is optimal  
when setting the speaker type.  
Song title & Artist name  
Album name & Artist name  
Folder name  
File name  
Play time & Track number  
Clock  
1 Enter Standby  
Press the [SRC] button.  
Select the "STANDBY" display.  
"P-TIME"  
"CLOCK"  
2 Enter Speaker Setting mode  
Press the [VOL] knob.  
In Standby/ Auxiliary input source  
3 Select the Speaker type  
Turn the [VOL] knob.  
Each time you turn the knob, the setting  
alternates between the settings shown in the  
table below.  
Information  
Auxiliary input name  
Clock  
Display  
"SRC NAME"  
"CLOCK"  
3 Exit Switching Display mode  
Press the Control knob.  
Speaker type  
OFF  
For 5 & 4 in. speaker  
For 6 & 6x9 in. speaker  
For the OEM speaker  
Display  
"SP OFF"  
"SP 5/4"  
"SP 6*9/6"  
"SP OEM"  
* If the contents of the information cannot be  
displayed, Play time or Frequency is displayed.  
Album name cannot be displayed in WMA file.  
4 Exit Speaker Setting mode  
Press the [VOL] knob.  
Dimmer Control  
You can lower the brightness of the display by  
using the dimmer function.  
Switching Display  
Changing the information displayed.  
Press the [ATT] button for at least 1 second.  
Each time you press the button for 1 second, the  
Dimmer control turns ON or OFF.  
When the Dimmer control is ON, "DIM ON" is  
displayed.  
1 Enter Switching Display mode  
Press the Control knob for at least 1 second.  
"DISP SEL" is displayed.  
2 Select the Display item  
Push the Control knob towards [4] or  
[¢].  
In Tuner source  
Information  
Frequency  
Clock  
Display  
"FREQ"  
"CLOCK"  
In CD & External disc source  
Information  
Disc title  
Track title  
Play time & Track number  
Clock  
Display  
"D-TITLE"*  
"T-TITLE"*  
"P-TIME"  
"CLOCK"  
English  
|
9
General features  
Theft Deterrent Faceplate  
TEL Mute  
The faceplate of the unit can be detached and  
taken with you, helping to deter theft.  
The audio system automatically mutes when a  
call comes in.  
Removing the Faceplate  
Press the Release button.  
When a call comes in  
"CALL" is displayed.  
The faceplate unlocks, allowing you to detach it.  
The audio system pauses.  
Listening to the audio during a call  
Press the [SRC] button.  
The "CALL" display disappears and the audio  
The faceplate is a precision piece of equipment and  
can be damaged by shocks or jolts.  
Keep the faceplate in its faceplate case while  
detached.  
Do not expose the faceplate (and the faceplate case)  
to direct sunlight or excessive heat or humidity. Also  
avoid places with too much dust or the possibility of  
water splashing.  
system comes back ON.  
When the call ends  
Hang up the phone.  
The "CALL" display disappears and the audio  
system comes back ON.  
Reattaching the Faceplate  
To use the TEL Mute feature, you need to hook up  
the MUTE wire to your telephone using a commercial  
telephone accessory. Refer to <Connection Wires to  
Terminals> (page 23).  
1 Align the projections on the unit with the  
grooves on the faceplate.  
Projections  
Grooves  
2 Push the faceplate in until it clicks.  
The faceplate is locked in place, allowing you to  
use the unit.  
|
10  
English  
Tuner features  
Control knob  
ST indicator  
Band display  
Frequency display  
Preset station number  
Tuning  
Tuning Mode  
Selecting the station.  
Choose the tuning mode.  
Press the [AUTO] button.  
1 Select tuner source  
Press the [SRC] button.  
Select the "TUNER" display.  
Each time you press the button, the Tuning  
mode alternates between the modes shown in  
the table below.  
2 Select the band  
Tuning mode  
Display  
Operation  
Automatic search for a station.  
Search in order of the stations  
in the Preset memory.  
Push the Control knob towards [FM] or [AM].  
Each time you push the knob toward [FM], it  
switches between the FM1, FM2, and FM3 bands.  
Auto seek  
"AUTO 1"  
Preset station seek "AUTO 2"  
Manual  
"MANUAL" Normal manual tuning control.  
3 Tune up or down band  
Push the Control knob towards [4] or  
[¢].  
During reception of stereo stations the "ST" indicator  
is ON.  
English  
|
11  
Tuner features  
Station Preset Memory  
Frequency Step Setting  
Putting a station in the memory.  
Changing the tuning frequency step.  
The original setting is FM band 50 kHz, and AM  
band 9 kHz.  
1 Select the band  
Push the Control knob towards [FM] or [AM].  
1 Turn the power OFF  
2 Select the frequency to put in the memory  
Push the Control knob towards [4] or  
[¢].  
Press the [SRC] button for at least 1 second.  
2 Switch the frequency step  
While pressing the [1] and [5] button, press  
the [SRC] button.  
Release your fingers from the button after the  
display appears.  
3 Put the frequency in the memory  
Press the desired [1] — [6] button for at least  
2 seconds.  
The preset number display blinks 1 time.  
On each band, 1 station can be put in the  
memory on each [1] — [6] button.  
The frequency step changes to FM band 200 kHz,  
and AM band 10 kHz.  
When the same operation is repeated, the frequency  
step returns to the original setting.  
When the frequency step is changed, the frequencies  
in the memory are deleted.  
Auto Memory Entry  
Putting stations with good reception in the  
memory automatically.  
1 Select the band for Auto Memory Entry  
Push the Control knob towards [FM] or [AM].  
2 Open Auto Memory Entry  
Press the [AME] button for at least 2 seconds.  
When 6 stations that can be received are put in  
the memory Auto Memory Entry closes.  
Preset Tuning  
Recalling the stations in the memory.  
1 Select the band  
Push the Control knob towards [FM] or [AM].  
2 Recall the station  
Press the desired [1] — [6] button.  
|
12  
English  
CD/Audio file/External disc control features  
Control knob  
Disc number  
IN indicator  
Play time  
Track number  
Function of the KDC-MP4533/KDC-MP4033/KDC-  
MP4033S  
Playing CD & Audio file  
Playing External Disc  
Playing discs set in the optional accessory disc  
player connected to this unit.  
When a disc is inserted  
Press the [SRC] button.  
Select the "CD" display.  
Press the [SRC] button.  
Select the display for the disc player you want.  
When a CD is inserted, the "IN" indicator is ON.  
Display examples:  
Pause and play  
Press the Control knob.  
Each time you press the knob, the audio pauses  
or plays.  
Display  
"CD CH"  
"MD CH"  
Disc player  
CD changer  
MD changer  
Eject the CD  
Press the [0] button.  
Pause and play  
Press the Control knob.  
Each time you press the knob, the audio pauses  
or plays.  
Disc 10 is displayed as "0".  
The functions that can be used and the information  
that can be displayed will differ depending on the  
external disc players being connected.  
English  
|
13  
CD/Audio file/External disc control features  
Function of the KDC-MP4533/KDC-MP4033/KDC-  
Fast Forwarding and Reversing  
MP4033S  
Function of disc changers with remote control  
Fast Forwarding  
Hold down toward [¢] with the Control  
knob.  
Direct Disc Search  
Doing Disc Search by entering the disc number.  
Release your finger to play the disc at that point.  
1 Enter the disc number  
Press the number buttons on the remote  
control.  
Reversing  
Hold down toward [4] with the Control  
knob.  
2 Do Disc Search  
Release your finger to play the disc at that point.  
Press the [+] or [] button.  
Cancelling Direct Disc Search  
Press the [38] button.  
There is no sound while the Audio file is being  
searched.  
Input "0" to select disc 10.  
Track/File Search  
Searching for a song on the disc or in the Audio  
file folder.  
Track/File/Disc/Folder Repeat  
Push the Control knob towards [4] or  
[¢].  
Replaying the song, disc in the Disc changer or  
Audio file folder you are listening to.  
Press the [REP] button.  
Each time you press the button, the Repeat Play  
alternates between the modes shown in the  
tables below.  
Function of disc changer/ Audio file  
Disc Search/Folder Search  
Selecting the disc set in the Disc changer or the  
folder recorded on the Audio file media.  
In CD & External disc source  
Repeat play  
Track Repeat  
Disc Repeat (In Disc Changer)  
OFF  
Display  
"TRAC REP"  
"DISC REP"  
"REP OFF"  
Push the Control knob towards [FM] or [AM].  
In Audio file  
Function of remote control  
Repeat play  
File Repeat  
Folder Repeat  
OFF  
Display  
Direct Track/File Search  
Doing Track/File Search by entering the track/file  
number.  
"FILE REP"  
"FOLD REP"  
"REP OFF"  
1 Enter the track/file number  
Press the number buttons on the remote  
control.  
2 Do Track/File Search  
Press the [4] or [¢] button.  
Cancelling Direct Track/File Search  
Press the [38] button.  
|
14  
English  
Function of Audio file  
Scan Play  
Playing the first part of each song on the disc  
or Audio file folder you are listening to and  
searching for the song you want to hear.  
Folder Select  
Quickly selecting the folder you want to hear.  
1 Enter Folder Select mode  
Press the [F.SEL] button.  
"FOLD SEL" is displayed.  
During Select mode the folder information is  
displayed as shown below.  
Folder name display  
1 Start Scan Play  
Press the [SCAN] button.  
"TRAC SCN"/"FILE SCN" is displayed.  
2 Release it when the song you want to listen  
to is played  
Press the [SCAN] button.  
Displays the current folder name.  
Random Play  
2 Select the folder level  
Playing all the songs on the disc in random order.  
Push the Control knob towards [FM] or [AM].  
With the [FM] of the Control knob, you move  
1 level down and with the [AM] of the Control  
knob, 1 level up.  
Press the [RDM] button.  
Each time you press the button, Random Play  
turns ON or OFF.  
When the Random mode is ON, "DISC RDM"/  
"FOLD RDM" is displayed.  
Selecting a folder in the same level  
Push the Control knob towards [4] or  
[¢].  
With the [4] of the Control knob, you move  
to the previous folder, and with the [¢] of the  
Control knob, to the next folder.  
When you push the Control knob toward [¢], the  
next random song starts.  
Returning to the top level  
Press the [3] button.  
Function of the KDC-MP4533/KDC-MP4033/KDC-  
MP4033S  
Function of disc changer  
3 Decide the folder to play  
Press the Control knob.  
Magazine Random Play  
Play the songs on all the discs in the disc changer  
in random order.  
The Folder Select mode releases, and the Audio  
file in the folder being displayed plays.  
Cancelling the Folder Select mode  
Press the [F.SEL] button.  
Press the [M.RDM] button.  
Each time you press the button, the Magazine  
Random Play turns ON or OFF.  
When the Magazine Random mode is ON,  
"MGZN RDM" is displayed.  
Text/Title Scroll  
Scrolling the displayed CD text, Audio file text, or  
MD title.  
When you push the Control knob toward [¢], the  
next random song starts.  
Push the Control knob toward [FM] for at  
least 2 seconds.  
English  
|
15  
Menu system  
Control knob  
Menu display  
You can continue by returning to step 2 and  
setting other items.  
Menu System  
Setting beep sound during operation, etc.  
functions.  
The Menu system basic operation method is  
explained here. The reference for the Menu items  
and their setting content is after this operation  
explanation.  
4 Exit Menu mode  
Press the [MENU] button.  
When other items those applicable to the basic  
operation method above are displayed, their setting  
content chart is entered. (Normally the setting listed at  
the top of the chart is the original setting.)  
Also, the explanation for items that are not applicable  
(<Manual Clock Adjustment> etc.) are entered step  
by step.  
1 Enter Menu mode  
Press the [MENU] button for at least 1 second.  
"MENU" is displayed.  
2 Select the menu item  
Push the Control knob towards [FM] or [AM].  
Example: When you want to set the beep sound,  
select the "BEEP" display.  
3 Set the menu item  
Push the Control knob towards [4] or  
[¢].  
Example: When you select "BEEP", each time you  
push the knob it alternates between  
"BEEP ON" or "BEEP OFF". Select 1 of  
them as the setting.  
|
16  
English  
Function of the KDC-MP4533/KDC-MP4033/KDC-  
Resetting the Security Code function when  
the audio unit is first used after removed  
from the battery power source or the Reset  
button is pressed  
MP4033S  
In Standby mode  
Security Code  
Activating the Security Code disables the usage  
of audio unit by someone else. Once the Security  
Code is activated, the entry of authorized Security  
Code is required to turn on the audio unit when  
it is removed from the vehicle. Indication of this  
Security Code activation prevents your precious  
audio unit from stealing.  
1 Turn the power ON.  
2 Do the step 4 through 7 step operation, and  
reenter the security code.  
"APPROVED" is displayed.  
Now, you can use the unit.  
If an incorrect code is entered, "WAITING" is displayed,  
and the input prohibition periods shown in the table  
below is generated.  
When you activate the Security Code function, it cannot  
be released.  
After the input prohibition time lapses, "CODE" is  
displayed, and you can reenter the code.  
Note, your Security Code is the 4 digit number entered in  
your "Car Audio Passport" in this package.  
Number of times the  
Input prohibited time  
incorrect code was input  
1 Enter Standby  
1
2
3
4
5 minutes  
1 hour  
Press the [SRC] button.  
Select the "STANDBY" display.  
2 Enter Menu mode  
24 hours  
Press the [MENU] button for at least 1 second.  
When "MENU" is displayed, "CODE SET" is  
displayed.  
In Standby mode  
3 Enter Security Code mode  
Press the Control knob for at least 2 seconds.  
When "ENTER" is displayed, "CODE" is also  
displayed.  
Touch Sensor Tone  
Setting the operation check sound (beep sound)  
ON/OFF.  
4 Select the digits to enter  
Push the Control knob towards [4] or  
[¢].  
Display  
"BEEP ON"  
"BEEP OFF"  
Setting  
Beep is heard.  
Beep canceled.  
5 Select the Security Code numbers  
Push the Control knob towards [FM] or [AM].  
6 Repeat steps 4 and 5, and complete the  
Security Code.  
7 Confirm the Security Code  
Press the Control knob for at least 3 seconds.  
When "RE-ENTER" is displayed, "CODE" is also  
displayed.  
8 Do the step 4 through 7 step operation, and  
reenter the security code.  
"APPROVED" is displayed.  
The Security Code function activates.  
If you enter a Code different from your Security Code,  
you have to start over from step 4.  
English  
|
17  
Menu system  
In Standby mode  
In CD mode  
Manual Clock Adjustment  
Supreme Setting  
When MP3 or WMA files encoded at a low bit  
rate (less than 96 kbps (fs=32k, 44.1k, 48kHz))  
are played, this function restores their high  
frequency region to approach the sound quality  
of equivalents of these files encoded at a high bit  
rate. Processing is optimized for the compression  
format used (MP3, or WMA), and adjustment is  
made for the bit rate used.  
1 Select Clock Adjustment mode  
Push the Control knob towards [FM] or [AM].  
Select the "CLK ADJ" display.  
2 Enter Clock Adjust mode  
Press the Control knob for at least 1 second.  
The clock display blinks.  
3 Adjust the hours  
Push the Control knob towards [FM] or [AM].  
Display  
Setting  
Adjust the minutes  
"SPRM ON"  
Plays sound using the Supreme function.  
Push the Control knob towards [4] or  
[¢].  
"SPRM OFF"  
Plays the original sound stored in the audio file.  
4 Exit Clock adjustment mode  
The sound effect may be imperceptible depending  
on the relationship between the audio file format and  
setting.  
Press the [MENU] button.  
Function of the KDC-MP4533/KDC-MP4033/KDC-  
MP4033S  
In FM reception  
DSI (Disabled System Indicator)  
A red indicator will blink on the unit after the  
faceplate is removed, warning potential thieves.  
CRSC (Clean Reception System  
Circuit)  
Temporarily have reception alternate from  
stereo to mono to reduce multi-path noise when  
listening to the FM station.  
Display  
"DSI ON"  
"DSI OFF"  
Setting  
LED flashes.  
LED OFF.  
Display  
Setting  
"CRSC ON"  
"CRSC OFF"  
The CRSC is ON.  
The CRSC is OFF.  
Strong electrical fields (such as from power lines) may  
cause unstable sound quality when CRSC is turned  
ON. In such a situation, turn it OFF.  
|
18  
English  
Function of the KDC-MP4533/KDC-MP4033/KDC-  
MP4033S  
Text Scroll  
Setting the displayed text scroll.  
Auxiliary Input Display Setting  
Display  
"SCL AUTO"  
"SCL MANU"  
Setting  
Repeats scroll.  
Scrolls when the display changes.  
Selecting the display when alternating to  
Auxiliary input source.  
1 Select Auxiliary input source  
Press the [SRC] button.  
Select the "AUX EXT" display.  
The text scrolled is listed below.  
- CD text  
2 Enter Menu mode  
- Folder name/ File name/ Song title/ Artist name/  
Album name  
- MD title  
Press the [MENU] button for at least 1 second.  
"MENU" is displayed.  
3 Select Auxiliary input display setting mode  
Push the Control knob towards [FM] or [AM].  
Select the "NAME SET" display.  
In Standby mode  
4 Enter Auxiliary input display setting mode  
Press the Control knob for at least 1 second.  
The selected Auxiliary input display is displayed.  
CD Read Setting  
When there is a problem with playing a CD with  
special format, this setting plays the CD by force.  
5 Select the Auxiliary input display  
Push the Control knob towards [4] or  
Display  
"CD READ1"  
"CD READ2"  
Setting  
Play CD and Audio file.  
Play CD by force.  
[¢].  
Each time you push the knob, the display  
alternates as listed below.  
• "AUX EXT"  
• "DVD"  
Setting "CD READ2" cannot play Audio file.  
• "PORTABLE"  
• "GAME"  
Some music CDs may not play even in the "CD  
READ2" mode.  
• "VIDEO"  
• "TV"  
6 Exit Auxiliary input display setting mode  
Press the [MENU] button.  
When operation stops for 10 seconds, the name at  
that time is registered, and the Auxiliary input display  
setting mode closes.  
You can only set the Auxiliary input display when the  
auxiliary input of optional KCA-S210A is used.  
English  
|
19  
Accessory of the KDC-MP4533/KDC-MP4033/KDC-MP4033S/KDC-MP333RC  
Basic Operations of remote control  
SRC  
VOL  
SRC  
ATT  
ATT  
VOL  
38  
AUD  
AUD  
38  
FM+  
AM–  
4
¢
4/¢  
FM/AM/+/–  
DIRECT  
/OK  
Not used  
Not used  
ABC  
JKL  
DEF  
GHI  
MNO  
[0] — [9]  
PRS  
TUV  
WXY  
QZ  
Loading and Replacing the battery  
Basic operations  
Use two "AA"/ "R6"-size batteries.  
Slide the cover while pressing downwards to  
remove it as illustrated.  
Insert the batteries with the + and – poles aligned  
properly, following the illustration inside the case.  
[VOL] buttons  
Adjusts the volume.  
[SRC] button  
Each time you press the button, the source  
alternates.  
For the source alternating order refer to  
<Selecting the Source> (page 7).  
[ATT] button  
Turns the volume down quickly.  
When the button is pressed again, the volume  
returns to the previous level.  
2WARNING  
Store unused batteries out of the reach of children.  
Contact a doctor immediately if the battery is  
accidentally swallowed.  
Do not set the remote control in hot places such as  
above the dashboard.  
|
20  
English  
Audio Control  
[AUD] button  
Selects the Audio item to be adjusted.  
[VOL] buttons  
Adjusts the Audio item.  
Refer to <Audio Control> (page 8) for the operation  
method, such as the procedures for Audio control and  
others operations.  
In Tuner source  
[FM]/ [AM] buttons  
Selects the band.  
Each time you press the [FM] button, the band  
alternates between the FM1, FM2, and FM3  
bands.  
[4]/ [¢] buttons  
Tune up or down band.  
[0] — [9] buttons  
Press buttons [1] — [6] to recall preset stations.  
In Disc source  
[4]/ [¢] buttons  
Going forwards and backwards between track/  
files.  
[+]/ [] buttons  
Going forwards and backwards between disc/  
folders.  
[38] button  
Each time you press the button, the song pauses  
or plays.  
[0] — [9] buttons  
When in <Direct Track/File Search> (page 14) and  
<Direct Disc Search> (page 14), enters the track/  
file/disc number.  
English  
|
21  
Accessories/ Installation Procedure  
Accessories  
If the power is not turned ON (or it is ON, but will be OFF  
immediately), the speaker wire may have a short-circuit  
or touched the chasis of the vehicle and the protection  
function may have been activated. Therefore, the speaker  
wire should be checked.  
1
..........1  
If your car’s ignition does not have an ACC position,  
connect the ignition wires to a power source that can be  
turned on and off with the ignition key. If you connect  
the ignition wire to a power source with a constant  
voltage supply, as with battery wires, the battery may die.  
If the console has a lid, make sure to install the unit so  
that the faceplate will not hit the lid when closing and  
opening.  
If the fuse blows, first make sure the wires aren’t touching  
to cause a short circuit, then replace the old fuse with  
one with the same rating.  
Insulate unconnected wires with vinyl tape or other  
similar material. To prevent a short circuit, do not remove  
the caps on the ends of the unconnected wires or the  
terminals.  
Connect the speaker wires correctly to the terminals to  
which they correspond. The unit may be damaged or fail  
to work if you share the - wires or ground them to any  
metal part in the car.  
When only two speakers are being connected to the  
system, connect the connectors either to both the front  
output terminals or to both the rear output terminals  
(do not mix front and rear). For example, if you connect  
the + connector of the left speaker to a front output  
terminal, do not connect the - connector to a rear  
output terminal.  
2
..........2  
..........4  
..........4  
..........1  
3
4
5
After the unit is installed, check whether the brake lamps,  
blinkers, wipers, etc. on the car are working properly.  
Mount the unit so that the mounting angle is 30° or less.  
Installation Procedure  
1. To prevent a short circuit, remove the key from  
the ignition and disconnect the - battery.  
2. Make the proper input and output wire  
connections for each unit.  
3. Connect the speaker wires of the wiring harness.  
4. Connect the wiring harness wires in the  
following order: ground, battery, ignition.  
5. Connect the wiring harness connector to the  
unit.  
6. Install the unit in your car.  
7. Reconnect the - battery.  
8. Press the reset button.  
2WARNING  
If you connect the ignition wire (red) and the battery wire  
(yellow) to the car chassis (ground), you may cause a short  
circuit, that in turn may start a fire. Always connect those  
wires to the power source running through the fuse box.  
|
22  
English  
Connecting Wires to Terminals  
Front left output (White)/ Front right output (Red)  
(KDC-MP4533 only)  
Rear left output (White)/ Rear right output (Red)  
To Kenwood disc changer/ External optional accessory  
(KDC-MP4533/MP4033/MP4033S only)  
To connect these leads, refer  
to the relevant instruction  
manuals.  
Fuse (10A)  
FM/AM antenna input  
Wiring harness  
(Accessory1)  
If no connections are made, do not let the wire come out from the tab.  
Power control wire (Blue/White)  
When using the optional power amplifier,  
connect to its power control terminal.  
P.CONT  
Depending on what antenna you are  
using, connect either to the control  
terminal of the motor antenna, or to the  
power terminal for the booster amplifier  
of the film-type antenna.  
Motor antenna control wire (Blue)  
TEL mute wire (Brown)  
ANT.  
CONT  
Connect to the terminal that is grounded  
when either the telephone rings or  
during conversation.  
MUTE  
To connect the  
Kenwood navigation  
system, consult your  
navigation manual.  
White/Black  
White  
To front left  
speaker  
FRONT  
L
Gray/Black  
Gray  
To front right  
speaker  
FRONT  
R
Green/Black  
Green  
To rear left  
speaker  
REAR  
REAR  
L
Purple/Black  
Purple  
To rear right  
speaker  
R
Ignition key  
switch  
Car fuse box  
ACC  
Ignition wire (Red)  
Battery wire (Yellow)  
Car fuse box  
(Main fuse)  
Ground wire (Black) - (To car chassis)  
Battery  
+
English  
|
23  
Installation  
non-Japanese cars  
Japanese cars  
1 Refer to the section <Removing the hard rubber  
frame> (page 26) and then remove the hard  
rubber frame.  
2 Align the holes in the unit (two locations on each  
side) with the vehicle mounting bracket and  
secure the unit with the accessory screws.  
Metal mounting strap  
(commercially available)  
Firewall or metal support  
T
N
T/N  
T
N
Bend the tabs of the  
T: Toyota cars  
N: Nissan cars  
mounting sleeve with a  
screwdriver or similar utensil  
and attach it in place.  
8 mm  
MAX.  
Self-tapping screw  
(commercially available)  
8mm  
MAX.  
3
4
ø5mm  
ø5mm  
Screw (M4X8)  
(commercially available)  
Accessory3...for Nissan car  
Accessory4 ...for Toyota car  
Make sure that the unit is installed securely in place. If  
the unit is unstable, it may malfunction (for example, the  
sound may skip).  
During installation, do not use any screws except for  
those provided. The use of different screws might result  
in damage to the main unit.  
Damage may occur if a screwdriver or similar tool is used  
with excessive force during the installations.  
|
24  
English  
Screwing the Faceplate on the Unit  
If you want to fasten the faceplate to the main  
unit so that it does not fall off, screw in the  
provided screws in the holes shown below.  
Accessory5  
Never insert the screw in any other screw hole than the  
one specified. If you screw them in another hole, it will  
contact and may cause damage to the mechanical parts  
inside the unit.  
English  
|
25  
Removing the Unit  
Removing the hard rubber frame  
Removing the Unit  
1 Engage the catch pins on the removal tool and  
remove the two locks on the upper level.  
Upper the frame and pull it forward as shown in  
the figure.  
1 Refer to the section <Removing the hard rubber  
frame> (page 26) and then remove the hard  
rubber frame.  
2 Remove the screw (M4 × 8) on the back panel.  
3 Insert the two removal tools deeply into the slots  
on each side, as shown.  
Screw (M4X8)  
(commercially available)  
Lock  
Catch  
Accessory2  
Removal tool  
2 When the upper level is removed, remove the  
lower two locations.  
Accessory2  
Removal tool  
4 Lower the removal tool toward the bottom, and  
pull out the unit halfway while pressing towards  
the inside.  
The frame can be removed from the bottom side in the  
same manner.  
Be careful to avoid injury from the catch pins on the  
removal tool.  
5 Pull the unit all the way out with your hands,  
being careful not to drop it.  
|
26  
English  
Troubleshooting Guide  
What might seem to be a malfunction in your unit  
may just be the result of slight misoperation or  
miswiring. Before calling service, first check the  
following table for possible problems.  
? No sound can be heard, or the volume is low.  
The fader or balance settings are set all the way to  
one side.  
Center the fader and balance settings.  
The input/output wires or wiring harness are  
connected incorrectly.  
Reconnect the input/output wires or the  
wiring harness correctly. See the section on  
<Connecting Wires to Terminals>.  
General  
? The power does not turn ON.  
The fuse has blown.  
The values of Volume offset are low.  
After checking for short circuits in the wires,  
replace the fuse with one with the same  
rating.  
Turn up the Volume offset, referring to the  
section on <Audio Setup> (page 8).  
? The sound quality is poor or distorted.  
? There’s a source you can’t switch.  
One of the speaker wires is being pinched by a  
screw in the car.  
There’s no media inserted.  
Set the media you want to listen to. If there’s  
no media in this unit, you can’t switch to each  
source.  
Check the speaker wiring.  
The speakers are not wired correctly.  
Reconnect the speaker wires so that each  
output terminal is connected to a different  
speaker.  
The Disc changer isn’t connected.  
Connect the Disc changer. If the Disc changer  
isn’t connected to it’s input terminal, You can’t  
switch to an external disc source.  
? The Touch Sensor Tone doesn’t sound.  
The preout jack is being used.  
? The memory is erased when the ignition is  
turned OFF.  
The Touch Sensor Tone can’t be output from  
the preout jack.  
The ignition and battery wire are incorrectly  
connected.  
Tuner source  
Connect the wire correctly, referring to the  
section on <Connecting Wires to Terminals>.  
? Radio reception is poor.  
The car antenna is not extended.  
? The TEL mute function does not work.  
The TEL mute wire is not connected properly.  
Pull the antenna out all the way.  
The antenna control wire is not connected.  
Connect the wire correctly, referring to the  
section on <Connecting Wires to Terminals>.  
Connect the wire correctly, referring to the  
section on <Connecting Wires to Terminals>.  
? The TEL mute function turns ON even though the  
TEL mute wire is not connected.  
The TEL mute wire is touching a metal part of the  
car.  
Pull the TEL mute wire away from the metal  
part of the car.  
? Even if Loudness is turned ON, high-pitched tone  
isn’t compensated for.  
Tuner source is selected.  
High-pitched tone isn’t compensated for when  
in Tuner source.  
English  
|
27  
Troubleshooting Guide  
Disc source  
Audio file source  
? "AUX EXT" is displayed without achieving  
? Cannot play an Audio file.  
External disc control mode.  
The media is scratched or dirty.  
Unsupported disc changer is connected.  
Clean the media, referring to the CD cleaning  
of the section on <About CDs> (page 5).  
Use the disc changer mentioned in the  
<About CD players/disc changers connected  
to this unit> (page 3) of the section on <Safety  
precautions>.  
? The sound skips when an Audio file is being  
played.  
The media is scratched or dirty.  
? The specified disc does not play, but another one  
plays instead.  
Clean the media, referring to the CD cleaning  
of the section on <About CDs> (page 5).  
The specified CD is quite dirty.  
Clean the CD.  
The recording condition is bad.  
Record the media again or use another media.  
The disc is loaded in a different slot from that  
specified.  
? The Audio file track time isn’t displayed correctly.  
---  
Eject the disc magazine and check the  
number for the specified disc.  
There are times when it isn’t displayed  
correctly according to the Audio file recording  
conditions.  
The disc is severely scratched.  
Try another disc instead.  
? Supreme does not take effect when it is turned  
ON.  
? A CD ejects as soon as it is loaded.  
The CD is quite dirty.  
Little high-frequency component.  
Clean the CD, referring to the CD cleaning of  
the section on <About CDs> (page 5).  
Supreme would not take effect with songs  
with little high-frequency component.  
? Can’t remove disc.  
The cause is that more than 10 minutes has  
Songs that have not been encoded at bit rates  
lower than 96 kbps (fs = 32k, 44.1 k, 48 kHz) or  
those that have been encoded at a variable bit  
rate cannot be decoded to reproduce their high-  
frequency components.  
elapsed since the vehicle ACC switch was turned  
OFF.  
The disc can only be removed within 10  
minutes of the ACC switch being turned OFF.  
If more than 10 minutes has elapsed, turn  
the ACC switch ON again and press the Eject  
button.  
---  
? The disc won’t insert.  
There’s already another disc inserted.  
Press the [0] button and remove the disc.  
? Direct Search can’t be done.  
Another function is ON.  
Turn Random Play or other functions OFF.  
? Track Search can’t be done.  
For the discs/folders first or last song.  
For each disc/folder, Track Search can’t be  
done in the backward direction for the first  
song or in the forward direction for the last  
song.  
|
28  
English  
READING:  
IN (Blink):  
The unit is reading the data on the disc.  
The messages shown below display your  
systems condition.  
The CD player section is not operating  
properly.  
Reinsert the CD. If the CD cannot be  
ejected or the display continues to flash  
even when the CD has been properly  
reinserted, please switch off the power  
and consult your nearest service center.  
EJECT:  
No disc magazine has been loaded in  
the changer. The disc magazine is not  
completely loaded.  
Load the disc magazine properly.  
No CD in the unit.  
Insert the CD.  
PROTECT:  
The speaker wire has a short-circuit or  
touches the chassis of the vehicle, and  
then the protection function is activated.  
Wire or insulate the speaker cable  
properly and press the reset button.  
NO DISC:  
TOC ERR:  
No disc has been loaded in the disc  
magazine.  
Load a disc into the disc magazine.  
No disc has been loaded in the disc  
magazine.  
Load a disc into the disc magazine.  
The CD is quite dirty. The CD is upside-  
down. The CD is scratched a lot.  
Clean the CD and load it correctly.  
NA FILE:  
An Audio file is played with a format that  
this unit can’t support.  
----  
COPY PRO:  
A copy-protected file is played.  
----  
E-05:  
The CD is upside-down.  
Load the CD correctly.  
BLANK:  
Nothing has been recorded on the MD.  
NO TRACK:  
No tracks are recorded on the MD,  
although it has a title.  
E-15:  
Media was played that doesn’t have data  
recorded that the unit can play.  
Use media that has data recorded that  
the unit can play.  
NO PANEL:  
E-77:  
The faceplate of the slave unit being  
connected to this unit has been removed.  
Replace it.  
The unit is malfunctioning for some reason.  
Press the reset button on the unit. If the  
"E-77" code does not disappear, consult  
your nearest service center.  
E-99:  
Something is wrong with the disc  
magazine. Or the unit is malfunctioning for  
some reason.  
Check the disc magazine. And then  
press the reset button on the unit. If the  
"E-99" code does not disappear, consult  
your nearest service center.  
HOLD:  
The protective circuit in the unit activates  
when the temperature inside the  
automatic disc changer exceeds 60°C  
(140°F), stopping all operation.  
Cool down the unit by opening  
the windows or turning on the air  
conditioner. As the temperature falls  
below 60°C (140°F), the disc will start  
playing again.  
LOAD:  
Discs are being exchanged in the Disc  
changer.  
English  
|
29  
Specifications  
Specifications subject to change without notice.  
Audio section  
FM tuner section  
Maximum output power  
KDC-MP4533/MP4033/MP4033S/MP433  
Frequency range (200 kHz space)  
: 87.9 MHz – 107.9 MHz  
: 50 W x 4  
KDC-MP333/MP333RC  
: 45 W x 4  
Full Bandwidth Power (at less than 1% THD)  
: 22 W x 4  
Frequency range (50 kHz space)  
: 87.5 MHz – 108.0 MHz  
Usable sensitivity (S/N = 30dB)  
: 9.3dBf (0.8 μV/75 Ω)  
Quieting Sensitivity (S/N = 50dB)  
: 15.2dBf (1.6 μV/75 Ω)  
Frequency response ( 3.0 dB)  
: 30 Hz – 15 kHz  
Signal to Noise ratio (MONO)  
: 70 dB  
Selectivity ( 400 kHz)  
: ≥ 80 dB  
Stereo separation (1 kHz)  
: 40 dB  
Speaker impedance  
: 4 - 8 Ω  
Tone action  
Bass : 100 Hz 8 dB  
Middle : 1 kHz 8 dB  
Treble : 10 kHz 8 dB  
Preout level / Load (during disc play)  
: 2000 mV/10 kΩ  
Preout impedance  
: ≤ 600 Ω  
AM tuner section  
Frequency range (10 kHz space)  
: 530 kHz – 1700 kHz  
Frequency range (9 kHz space)  
: 531 kHz – 1611 kHz  
Usable sensitivity (S/N = 20dB)  
: 28 dBμ (25 μV)  
General  
Operating voltage (11 – 16V allowable)  
: 14.4 V  
Current consumption  
: 10 A  
Installation Size (W x H x D)  
: 182 x 53 x 155 mm  
Weight  
: 1.4 kg  
CD player section  
Laser diode  
: GaAlAs  
Digital filter (D/A)  
: 8 Times Over Sampling  
D/A Converter  
: 1 Bit  
Spindle speed  
: 1000 – 400 rpm (CLV 2times)  
Wow & Flutter  
: Below Measurable Limit  
Frequency response ( 1 dB)  
: 10 Hz – 20 kHz  
Total harmonic distortion (1 kHz)  
KDC-MP4533: 0.008 %  
KDC-MP4033/MP4033S/MP433/MP333/  
MP333RC: 0.01 %  
Signal to Noise ratio (1 kHz)  
KDC-MP4533: 110 dB  
KDC-MP4033/MP4033S/MP433/MP333/  
MP333RC: 105 dB  
Dynamic range  
: 93 dB  
MP3 decode  
: Compliant with MPEG-1/2 Audio Layer-3  
WMA decode  
: Compliant with Windows Media Audio  
|
30  
English  

Nespresso Coffeemaker TK30N01GB User Manual
Motorola SPICETM XT300 User Manual
Motorola MOTORAZR VM9 User Manual
Melissa COFFEMAKER 245 069 User Manual
Marlin 94 User Manual
Kenwood KDC 3023 User Manual
JVC KD G427 User Manual
Jensen JMC 326 User Manual
Emerson CKS5055B User Manual
Audiovox CTX5000 User Manual