Maxtor DIAMONDMAX 90576D4 User Manual

This document is a condensed version of the full Product Reference Manual.  
This version only includes the Maxtor Information about the Product. Information  
that can be found in the ANSI specification is not included in this document to  
reduce its over all size. Also eliminated are the Table of Contents and Glossary.  
This condensed version is created to allow faster downloading from Maxtor's  
Internet home page and MaxFax services.  
DiamondMax2880  
91152D8, 91008D7, 90845D6, 90840D6,  
90720D5, 90648D5, 90576D4, 90510D4,  
90432D3, 90288D2, 90256D2  
Part #1390/A  
All material contained herein Copyright © 1998 Maxtor Corporation.  
DiamondMax™, DiamondMax™ 1280, DiamondMax™ 1750, Diamond-  
Max™ 2160, DiamondMax™ 2880 and MaxFax™ are trademarks of Maxtor  
Corporation. No Quibble® Service is a registered trademark of Maxtor  
Corporation. Other brands or products are trademarks or registered  
trademarks of their respective holders. Contents and specifications subject  
to change without notice. All rights reserved. Printed in the U.S.A. 2/98  
Corporate Headquarters  
510 Cottonwood Drive  
Milpitas, California 95035  
Tel: 408-432-1700  
Fax: 408-432-4510  
Research and Development  
Engineering Center  
2190 Miller Drive  
Longmont, Colorado 80501  
Tel: 303-651-6000  
Fax: 303-678-2165  
BeforeYou Begin  
Thank you for your interest in the Maxtor DiamondMax™ 2880 AT hard disk drives. This manual provides  
technical information for OEM engineers and systems integrators regarding the installation and use of DiamondMax  
hard drives Drive repair should be performed only at an authorized repair center. For repair information, contact  
theMaxtorCustomerServiceCenterat800-2MAXTORor408-432-1700.  
Before unpacking the hard drive, please review Sections 1 through 4.  
CAUTION  
Maxtor DiamondMax 2880 hard drives are precision products. Failure to  
follow these precautions and guidelines outlined here may lead to  
product failure, damage and invalidation of all warranties.  
1
2
BEFOREunpackingorhandlingadrive,takeallproperelectro-staticdischarge(ESD)  
precautions,includingpersonnelandequipmentgrounding.Stand-alonedrivesaresensitiveto  
ESDdamage.  
BEFOREremovingdrivesfromtheirpackingmaterial,allowthemtoreachroom  
temperature.  
3
4
Duringhandling,NEVERdrop,jar,orbumpadrive.  
OnceadriveisremovedfromtheMaxtorshippingcontainer,IMMEDIATELYsecurethedrive  
throughitsmountingholeswithinachassis.Otherwise,storethedriveonapadded,grounded,  
antistaticsurface.  
5
NEVERswitchDCpowerontothedrivebyplugginganelectricallyliveDCsourcecableinto  
thedrive'sconnector.NEVERconnectalivebustothedrive'sinterfaceconnector.  
Please do not remove or cover up Maxtor factory-installed drive labels.  
They contain information required should the drive ever need repair.  
DIAMONDMAX2880INTRODUCTION  
SECTION 1  
Introduction  
Maxtor Corporation  
Maxtor Corporation has been providing high-quality computer storage products since 1982. Along the way,  
we’ve seen many changes in data storage needs. Not long ago, only a handful of specific users needed more than  
a couple hundred megabytes of storage. Today, downloading from the Internet and CD-ROMs, multimedia,  
networking and advanced office applications are driving storage needs even higher. Even home PC applications  
need capacities measured in gigabytes, not megabytes.  
Products  
Maxtor’s products meet those demanding storage capacity requirements with room to spare. They feature  
proven compatibility and reliability. While DiamondMax2880 is the latest addition to our family of high  
performance desktop hard drives, the DiamondMax™ 2160 and DiamondMax™ 1750 series hard drives  
deliver industry-leading capacity, performance and value for many PC applications.  
Support  
No matter which capacity, all Maxtor hard drives are supported by our commitment to total customer  
satisfaction and our No Quibble® Service guarantee. One call – or a visit to our home page on the Internet  
provide you the information you need quickly, accurately and in the form you prefer – a fax, a downloaded  
file or a conversation with a representative.  
Manual Organization  
This hard disk drive reference manual is organized in the following method:  
Section 1 – Introduction  
Section 2 – Description  
Section 3 – Specifications  
Section 4 – Installation  
Section 5 – AT Interface  
Section 6 – Host Software Interface  
Section 7 – Interface Commands  
Section 8 – Service and Support  
Appendix – Glossary  
Abbreviations  
ABBRV DESCRIPTION  
ABBRV DESCRIPTION  
ATA AT attachment  
bpi bits per inch  
MB megabyte  
Mbits/sec megabits per second  
CHS cylinder - head - sector  
db decibels  
MB/sec megabytes per second  
MHz megahertz  
dBA decibels, A weighted  
DMA direct memory access  
ECC error correction code  
fci flux changes per inch  
ms millisecond  
MSB most significant bit  
mV millivolts  
ns nanoseconds  
G
acceleration  
PIO programmed input/output  
RPM revolutions per minute  
tpi tracks per inch  
GB gigabyte  
Hz hertz  
KB kilobyte  
UDMA ultra direct memory access  
µsec microsecond  
LBA logical block address(ing)  
LSB least significant bit  
mA milliamperes  
V
volts  
W
watts  
1 – 4  
DIAMONDMAX2880INTRODUCTION  
Conventions  
If there is a conflict between text and tables, the table shall be accepted as being correct.  
Key Words  
The names of abbreviations, commands, fields and acronyms used as signal names are in all uppercase type  
(e.g., IDENTIFY DRIVE). Fields containing only one bit are usually referred to as the “name” bit instead of  
the “name” field.  
Names of drive registers begin with a capital letter (e.g., Cylinder High register).  
Numbering  
Numbers that are not followed by a lowercase “b” or “h” are decimal values. Numbers that are followed by  
a lowercase “b” (e.g., 01b) are binary values. Numbers that are followed by a lowercase “h” (e.g., 3Ah) are  
hexadecimal values.  
Signal Conventions  
Signal names are shown in all uppercase type.  
All signals are either high active or low active signals. A dash character (-) at the end of a signal name  
indicates that the signal is low active. A low active signal is true when it is below ViL and is false when it is  
above ViH. A signal without a dash at the end indicates that the signal is high active. A high active signal is  
true when it is above ViH and is false when it is below ViL.  
When a signal is asserted, it means the signal is driven by an active circuit to its true state.  
When a signal is negated, it means the signal is driven by an active circuit to its false state.  
When a signal is released, it means the signal is not actively driven to any state. Some signals have bias  
circuitry that pull the signal to either a true or false state when no signal driver is actively asserting or negating  
the signal. These instances are noted under the description of the signal.  
1 – 5  
SECTION 2  
Product Description  
Maxtor DiamondMax™ 2880 AT disk drives are 1-inch high, 3.5-inch diameter random access storage devices  
which incorporate an on-board ATA/Ultra DMA controller. High capacity is achieved by a balanced  
combination of high areal recording density and the latest data encoding and servo techniques.  
Maxtor's latest advancements in electronic packaging and integration methods have lowered the drive's power  
consumption and increased its reliability. Advanced magneto-resistive read/write heads, an state-of-the-art head/  
disk assembly using an integrated motor/spindle design allow up to four disks in a 3.5-inch package.  
Exceptionally high data transfer rates and 9.0 ms access times make these performance series disk drives especially  
well-suited to high speed desktop and server applications.  
DiamondMax 2880 Key Features  
ANSI ATA-4 compliant PIO Mode 4 interface (Enhanced IDE)  
Supports Ultra DMA Mode 2 for up to 33 MB/sec data transfers  
256 KB buffer with multi-adaptive cache manager  
9.0 ms seek time  
Zone density and I.D.-less recording  
High reliability with > 500,000 hour MTBF  
Outstanding shock resistance at 200 Gs  
High durability with 50K constant start/stop cycles  
Advanced multi-burst on-the-fly Error Correction Code (ECC)  
Extended data integrity with ECC protected data and fault tolerant servo synchronization fields  
Supports EPA Energy Star Standards (Green PC Friendly) with ATA powering savings commands  
Auto park and lock actuator mechanism  
Low power consumption  
S.M.A.R.T. Capability  
Note: Maxtor defines one megabyte as 106 or one million bytes and one gigabyte as 109 or one billion bytes.  
2 – 1  
PRODUCTDESCRIPTION  
Product Features  
Functional / Interface  
Maxtor DiamondMax™ 2880 hard drives contain all necessary mechanical and electronic parts to interpret control  
signals and commands from an AT-compatible host computer. See Section 3 Product Specifications, for complete  
drive specifications.  
Zone Density Recording  
The disk capacity is increased with bit density management – common with Zone Density Recording. Each  
disk surface is divided into 16 circumferential zones. All tracks within a given zone contain a constant  
number of data sectors. The number of data sectors per track varies in different zones; the outermost zone  
contains the largest number of data sectors and the innermost contains the fewest.  
Read/Write Multiple Mode  
This mode is implemented per ANSI ATA/ATAPI-4 specification. Read/Write Multiple allows the host to  
transfer a set number of sectors without an interrupt request between them, reducing transfer process  
overhead and improving host performance.  
UltraDMA - Mode 2  
Maxtor DiamondMax 2880 hard drives fully comply with the new ANSI Ultra DMA protocol, which greatly  
improves overall AT interface performance by significantly improving burst and sustained data throughput.  
Multi-word DMA (EISA Type B) - Mode 2  
Supports multi-word Direct Memory Access (DMA) EISA Type B mode transfers.  
Sector Address Translation  
All DiamondMax 2880 drives feature a universal translate mode. In an AT/EISA-class system, the drive may  
be configured to any specified combination of cylinders, heads and sectors (within the range of the drive's  
formatted capacity). DiamondMax 2880 drives power-up in a translate mode:  
MODEL  
91152D8  
91008D7  
90845D6  
90840D6  
90720D5  
90648D5  
90576D4  
90510D4  
90432D3  
90288D2  
90256D2  
CYL  
HD  
16  
16  
16  
16  
16  
16  
16  
16  
16  
16  
16  
SPT  
63  
63  
63  
63  
63  
63  
63  
63  
63  
63  
63  
LZone  
(*)  
(*)  
(*)  
(*)  
(*)  
(*)  
(*)  
(*)  
WPcom  
(*)  
CAPACITY  
11,520 MB  
10,080 MB  
8,455 MB  
8,400 MB  
7,200 MB  
6,480 MB  
5,760 MB  
5,122 MB  
4,320 MB  
2,880 MB  
2,560 MB  
22,332  
19,540  
16,383  
16,276  
13,957  
12,555  
11,166  
9,925  
(*)  
(*)  
(*)  
(*)  
(*)  
(*)  
(*)  
(*)  
8,374  
5,583  
4,960  
(*)  
(*)  
(*)  
(*)  
(*)  
(*) The fields LZone (Landing Zone) and WPcom (Write Pre-comp) are not used by the Maxtor hard drive  
and the values may be either 0 or the values set by the BIOS. All capacities listed in the above table are based  
on 106 or one million bytes.  
2 – 2  
PRODUCTDESCRIPTION  
Logical Block Addressing  
The Logical Block Address (LBA) mode can only be utilized in systems that support this form of translation.  
The cylinder, head and sector geometry of the drive, as presented to the host, differs from the actual physical  
geometry. The host AT computer may access a drive of set parameters: number of cylinders, heads and  
sectors per track, plus cylinder, head and sector addresses. However, the drive can’t use these host parameters  
directly because of zoned recording techniques. The drive translates the host parameters to a set of logical  
internal addresses for data access.  
The host drive geometry parameters are mapped into an LBA based on this formula:  
LBA  
= (HSCA - 1) + HHDA x HSPT + HNHD x HSPT x HCYA  
= (HSCA - 1) + HSPT x (HHDA + HNHD x HCYA)  
HSCA = Host Sector Address, HHDA = Host Head Address  
HCYA = Host Cylinder Address, HNHD = Host Number of Heads  
HSPT = Host Sectors per Track  
(1)  
(2)  
where  
The LBA is checked for violating the drive capacity. If it does not, the LBA is converted to physical drive  
cylinder, head and sector values. The physical address is then used to access or store the data on the disk and  
for other drive related operations.  
Defect Management Zone (DMZ)  
Each drive model has a fixed number of spare sectors per drive, all of which are located at the end of the  
drive. Upon detection of a bad sector that has been reassigned, the next sequential sector is used.  
For example, if sector 3 is flagged, data that would have been stored there is “pushed down” and recorded  
in sector 4. Sector 4 then effectively becomes sector 3, as sequential sectors are “pushed down” across the  
entire drive. The first spare sector makes up for the loss of sector 3, and so maintains the sequential order of  
data. This push down method assures maximum performance.  
On-the-Fly Hardware Error Correction Code (ECC)  
33 bits, single burst, guaranteed  
Software ECC Correction  
81 bits, single burst, guaranteed  
33 bits, double bursts, guaranteed  
Automatic Park and Lock Operation  
Immediately following power down, dynamic braking of the spinning disks delays momentarily allowing the  
read/write heads to move to an inner mechanical stop. A small fixed magnet holds the rotary actuator in  
place as the disk spins down. The rotary actuator is released only when power is again applied.  
2 – 3  
PRODUCTDESCRIPTION  
Cache Management  
Buffer Segmentation  
The data buffer is organized into two segments: the data buffer and the micro controller scratch pad.  
The data buffer is dynamically allocated for read and write data depending on the commands received.  
A variable number of read and write buffers may exist at the same time.  
Read-Ahead Mode  
Normally, this mode is active. Following a read request, disk read-ahead begins on the first sector and  
continues sequentially until the allocated buffer is full. If a read request is received during the read-ahead  
operation, the buffer is examined to determine if the request is in the cache. If a cache hit occurs, read-  
ahead mode continues without interruption and the host transfer begins immediately.  
Automatic Write Reallocation (AWR)  
This feature is part of the write cache and reduces the risk of data loss during deferred write operations. If a  
disk error occurs during the disk write process, the disk task stops and the suspect sector is reallocated to a  
pool of alternate sectors located at the end of the drive. Following reallocation, the disk write task continues  
until it is complete.  
Write Cache Stacking  
Normally, this mode is active. Write cache mode accepts the host write data into the buffer until the buffer  
is full or the host transfer is complete. A command complete interrupt is generated at the end of the transfer.  
A disk write task begins to store the host data to disk. Host write commands continue to be accepted and  
data transferred to the buffer until either the write command stack is full or the data buffer is full. The drive  
may reorder write commands to optimize drive throughput.  
2 – 4  
PRODUCTDESCRIPTION  
Major HDA Components  
Drive Mechanism  
A brush-less DC direct drive motor rotates the spindle at 5,400 RPM (±0.1%). The dynamically balanced  
motor/spindle assembly ensures minimal mechanical run-out to the disks. A dynamic brake provides a fast  
stop to the spindle motor upon power removal. The speed tolerance includes motor performance and motor  
circuit tolerances.  
Rotary Actuator  
All DiamondMax™ 2880 drives employ a rotary voice coil actuator which consists of a moving coil, an  
actuator arm assembly and stationary magnets. The actuator moves on a low-mass, low-friction center shaft.  
The low friction contributes to fast access times and low power consumption.  
Read/Write Electronics  
An integrated circuit mounted within the sealed head disk assembly (near the read/write heads) provides up  
to eight head selection (depending on the model), read pre-amplification and write drive circuitry.  
Read/Write Heads and Media  
Low mass, low force magneto-resistive read/write heads record data on 3.5-inch diameter disks. Maxtor uses  
a sputtered thin film medium on all disks for DiamondMax 2880 drives.  
Air Filtration System  
All DiamondMax 2880 drives are assembled in a Class 100 controlled environment. Over the life of the drive,  
a 0.1 micron filter and breather filter located within the sealed head disk assembly (HDA) maintain a clean  
environment to the heads and disks. DiamondMax 2880 drives are designed to operate in a typical office  
environment with minimum environmental control.  
Microprocessor  
The microprocessor controls the following functions for the drive electronics:  
Command execution  
Cache management  
Data correction and error recovery  
Diagnostic execution  
Data sequencing  
Head positioning (including error recovery)  
Host interface  
Index detection  
Spin speed control  
Seeks  
Servo  
S.M.A.R.T.  
2 – 5  
PRODUCTDESCRIPTION  
Subsystem Configuration  
Dual Drive Support  
Two drives may be accessed via a common interface cable, using the same range of I/O addresses. The drives  
are jumpered as device 0 or 1 (Master/Slave), and are selected by the drive select bit in the  
Device/Head register of the task file.  
All Task File registers are written in parallel to both drives. The interface processor on each drive decides  
whether a command written to it should be executed; this depends on the type of command and which  
drive is selected. Only the drive selected executes the command and activates the data bus in response to  
host I/O reads; the drive not selected remains inactive.  
A master/slave relationship exists between the two drives: device 0 is the master and device 1 the slave.  
When J50 is closed (factory default, figure 2-1), the drive assumes the role of master; when open, the drive  
acts as a slave. In single drive configurations, J50 must be closed.  
Cable Select Option  
CSEL (cable select) is an optional feature per ANSI ATA specification. Drives configured in a multiple drive  
system are identified by CSEL’s value:  
– If CSEL is grounded, then the drive address is 0.  
– If CSEL is open, then the drive address is 1.  
Jumper Location/Configuration  
Darkened jumper pins indicate factory-installed (default) shunts.  
JUMPER CONFIGURATION  
J50  
J48  
J46  
J44  
J42  
Master/Slave  
Only drive in single drive system*  
Master drive in dual drive system*  
Slave drive in dual drive system  
C
C
O
Cable Select  
Disabled*  
Enabled  
O
C
4092 Cylinder Limitation  
Disabled*  
Enabled  
O
C
Factory Reserved  
Factory Reserved  
O
O
Key * = Default C = Closed (jumper installed) O = Open (no jumper installed)  
Figure 2-1  
PCBA Jumper Location and Configuration  
4092 Cylinder Limitation  
On some older BIOS', primarily those that auto-configure the disk drive, a hang may occur when the drive  
cylinder value exceeds 4096. The 4092 Cylinder Limitation jumper reduces the capacity in the Identify Drive to  
4092 allowing large capacity drives to work with older BIOS'. A software driver is required to access the full  
capacity of the drive.  
2 – 6  
SECTION 3  
Product Specifications  
Models and Capacities  
91152D8 91008D7 90845D6 90840D6 90720D5 90648D5 90576D4 90510D4 90432D3 90288D2 90256D2  
MODEL  
11,520 10,080 8,455 8,400 7,200 6,480 5,760 5,122 4,320 2,880 2,560  
Formatted Capacity (MB LBA Mode)  
Maxtor defines one megabyte as 106 or one million bytes and one gigabyte as 109 or one billion bytes.  
Drive Configuration  
MODEL  
91152D8 91008D7 90845D6 90840D6 90720D5 90648D5 90576D4 90510D4 90432D3 90288D2 90256D2  
Integrated Controller / Interface  
Encoding Method  
Interleave  
ATA-4 /EIDE  
EPR4 RLL 16/17  
1:1  
Servo System  
Embedded  
Buffer Size / Type  
Data Zones per Surface  
Data Surfaces / Heads  
Aerial Density  
256 KB SDRAM  
16  
5
7
8
6
6
5
4
4
3
2
2
2,000 Mb / in2  
Tracks per Surface (Cylinders)  
Track Density  
10,022  
9,800 tpi  
Flux Density  
166-21  
156-20  
512  
20 -330  
22,510,656 19,696,320 16,514,064 16,406,250 14,068,656 12,656,250 11,255,328 10,004,400 8,440,992 5,627,664 5,000,000  
8
kfci  
Recording Density  
Bytes per Sector / Block  
Sectors per Track  
Sectors per Drive  
5
kbpi  
0
Performance Specifications  
91152D8  
91008D7 90864D6 90840D6 90720D5 90640D5 90576D4 90525D4 90432D3 90288D2 90256D2  
MODEL  
Seek Times (typical)1  
Track-to-track  
< 1.0 ms  
9.0 ms  
Average  
Maximum  
< 18 ms  
5.56 ms  
5,400 RPM  
Average Latency  
Rotational Speed (±0.1%)  
Controller Command Overhead  
Data Transfer Rate  
< 0. ms  
5
up to 33.0 MB/sec  
up to 16.7 MB/sec  
To/from Interface  
(Ultra DMA - Mode 2)  
To/from Interface  
(PIO 4/Multi-word DMA - Mode 2)  
To/from Media  
up to 15.2 MB/sec  
9.0 sec typical  
Start Time (0 to Drive Ready)  
1 Controller overhead not included  
3 – 7  
PRODUCTSPECIFICATIONS  
Physical Dimensions  
PARAMETER  
STANDARD  
METRIC  
Height  
Length  
Width  
Weight  
1.02 inch  
25.9 millimeters  
146.6 millimeters  
102.1 millimeters  
0.59 kilograms  
5.77 inches  
4.02 inches  
1.3 pounds  
Figure 3 - 1  
Outline and Mounting Dimensions  
3 – 8  
PRODUCTSPECIFICATIONS  
Power Requirements (Average)  
MODE  
12V ± 8%  
1600 mA  
620 mA  
215 mA  
245 mA  
7 mA  
5V ± 5%  
200 mA  
330 mA  
350 mA  
225 mA  
245 mA  
140 mA  
POWER  
20.2 W  
9.0 W  
4.3 W  
4.1 W  
1.3 W  
Spin-up (peak)  
Seek  
Read/Write  
Idle  
Standby  
Sleep  
7 mA  
0.8 W  
Power Mode Definitions  
Spin-up  
The drive is spinning up following initial application of power and has not yet reached full speed.  
Seek  
A random access operation by the disk drive.  
Read/Write  
Data is being read from or written to the drive.  
Idle  
The drive is spinning, the actuator is parked and powered off and all other circuitry is powered on.  
The drive is capable of responding to read commands within 40 ms.  
Standby  
The spin motor is not spinning. The drive will leave this mode upon receipt of a command that requires  
disk access. The time-out value for this mode is programmable. The buffer is active to accept write data.  
Sleep  
This is the lowest power state – with the interface set to inactive. A software or hardware reset is required  
to return the drive to the Standby state.  
EPA Energy Star Compliance  
Maxtor Corporation supports the goals of the U.S. Environmental Protection Agency’s Energy Star program  
to reduce the electrical power consumption of computer equipment.  
Environmental Limits  
PARAMETER  
OPERATING  
NON-OPERATING/STORAGE  
Temperature  
5° C to 55° C  
low temperature (-40° C) per MIL-STD-810E, method 502.3.  
high temperature (71° C) per MIL-STD-810E, method 501.3,  
climatic category; hot-induced conditions.  
Thermal Gradient  
Relative Humidity  
Wet Bulb  
25° C per hour (maximum)  
5% to 95% (non-condensing)  
27° C (maximum)  
Altitude  
-200 to 10,000 feet  
(with any naturally occurring  
Per MIL-STD-810E, method 500.3, low pressure (altitude) test  
procedure I. storage; test condition 2, transport aircraft cargo  
temperature and humidity rate within compartment pressure.  
this range)  
Acoustic Noise (Idle mode)  
36 dBA average sound power  
(per ISO 7779, 10 microphone)  
3 – 9  
PRODUCTSPECIFICATIONS  
Shock and Vibration  
PARAMETER  
OPERATING  
NON-OPERATING  
Mechanical Shock  
Random Vibration  
20 Gs, 2.0 ms, no errors  
200 Gs, 2.0 ms, no damage  
Per MIL-STD-810E, method 514.4, basic  
transportation, vertical axis PSD profile.  
10 - 300 Hz at 0.004 G2/Hz  
10 Hz at 0.015 G2/Hz  
40 Hz at 0.015 G2/Hz  
500 Hz at 0.00015 G2/Hz  
301 - 500 Hz at 0.0006 G2/Hz  
Swept Sine Vibration  
5 - 20 Hz  
21 - 300 Hz  
0.049 inches double amplitude  
1.0 G peak amplitude (0 - peak)  
Reliability Specifications  
AFR  
< 1.7%  
The annualized average failure rate (AFR) applies to the period prior  
to the expiration of component design life, and is based on failures  
chargeable to Maxtor.  
MTBF  
> 500,000 hours  
Maxtor does not differentiate between various usage profiles (e.g.,  
power-on hours, power saving modes, non-operating periods or  
operating temperatures within the published specification.)  
Quality Acceptance Rate  
TBD (< 1,500 DPPM)  
The quality acceptance rate indicates the percentage of Maxtor  
products successfully installed by our customers, and/or the number  
of defective parts per million (DPPM) encountered during the entire  
installation process.  
Start/Stop Cycles  
50,000 (minimum)  
This indicates the minimum cycles for reliable start/stop function at a  
60% confidence level.  
Data Reliability  
< 1 per 1014 bits read  
Data errors (non-recoverable). Average data error rate allowed with all  
error recovery features activated.  
Component Design Life  
5 years (minimum)  
Component design life is defined as a.) the time period before  
identified wear-out mechanisms impact the failure rate, or b.) the time  
period up to the wear-out point when useful component life expires.  
3 – 10  
PRODUCTSPECIFICATIONS  
EMC/EMI  
Radiated Electromagnetic Field Emissions - EMC Compliance  
The hard disk drive mechanism is designed as a subassembly for installation into a suitable enclosure and is  
therefore not subject to Subpart J of Part 15 of FCC Rules (47CFR15) or the Canadian Department of  
Communications Radio Interference Regulations. Although not required, the disk mechanism has been  
tested within a suitable end-use product and found to comply with Class B limits of the FCC Rules and  
Regulations of the Canadian Department of Communications.  
The CE Marking indicates conformity with the European Union Low Voltage Directive (73/23/EEC) when  
the disk mechanism is installed in a typical personal computer. Maxtor recommends that testing and analysis  
for EMC compliance be performed with the disk mechanism installed within the user's end-use application.  
Canadian Emissions Statement  
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set  
out in the radio interference regulations of the Canadian department of communications.  
Le present appareil numerique n'emet pas de bruit radioelectriques depassant les limites applicables aux  
appareils numeriques de Class B prescrites dans le reglement sur le brouillage radioelectrique edicte par le  
ministere des communications du Canada.  
Radiated Magnetic Field Emissions  
Minimum of VDE Class B and MIL-STD-461/462, Method RE01 (stand-alone test configuration).  
Radiated Electromagnetic Field Immunity  
IEC 801-3, Class 2 compliance.  
Radiated Magnetic Field Immunity  
Per MIL-STD-461/462, Method RD01(15 Hz to 100 kHz, stand-alone test configuration).  
Standard Test Methods  
Traditional hard drive specifications are open to incorrect interpretation, but internationally recognized standard  
test methods accurately measure how products perform in real-world conditions. These methods have gained  
worldwide acceptance since they reflect actual environments, have well-defined test requirements, are easily  
understood and provide repeatable results. They objectively demonstrate to our customers the reliable, durable  
design of Maxtor hard drives. Each international test specification provides the basic method and condition  
information needed for reference by a knowledgeable Test and Qualification Engineer.  
Acoustic specifications such as sound pressure are misleading because the test methods used are not controlled  
by recognizable standards. The sound pressure measurement itself is the least meaningful indicator of noise  
emissions as it relates to the human ear. The specification of sound power, loudness and sharpness are  
considered the most accurate acoustic measurement methodologies recognized by the leading acoustic  
measurement experts. ISO 7779, sound power, is a repeatable test method providing results reproducible in any  
properly equipped acoustic lab.  
Safety Regulatory Compliance  
All Maxtor DiamondMax™ 2880 drives comply with relevant product safety standards such as CE, CUL, TUV  
and UL rules and regulations. As delivered, DiamondMax 2880 hard disk drives are designed for system  
integration before they are used.  
3 – 11  
INSTALLATION  
SECTION 4  
Handling and Installation  
Pre-formatted Drive  
This Maxtor hard drive has been formatted at the factory. Do not use a low-level formatting program.  
Important Notice  
There are a number of system BIOS’s currently in use which do not support hard drives with more than 4095  
cylinders (2.1 gigabytes). This section contains information describing the conditions which may identify this  
limitation. In order to obtain the full capacity of your Maxtor drive, you will need to follow the recommended  
installation instructions.  
Hard Drive Handling Precautions  
During handling, NEVER drop, jar, or bump a drive. Handle the drive by its sides and avoid touching the printed circuit  
board assembly (PCBA).  
Hard drives are sensitive to electrostatic discharge (ESD) damage. Use proper ESD practices by grounding yourself  
and the computer system the hard drive will be installed in.  
Allow the hard drive to reach room temperature BEFORE installing it in your computer system.  
NEVER switch DC power onto the drive by plugging an electrically live DC source cable into the drive's connector.  
NEVER connect a live connector to the hard drive's IDE interface connector.  
Electro-Static Discharge (ESD)  
To avoid some of the problems associated with ESD, Maxtor advises that anyone handling a disk drive use a  
wrist strap with an attached wire connected to an earth ground. Failure to observe these precautions voids the  
product warranty.  
Manufacturers frequently experience “unsolved” component/hardware malfunctions often caused by ESD. To  
reduce the incidence of ESD-related problems, Maxtor recommends that any electronics manufacturing plans  
include a comprehensive ESD program, the basic elements and functions of which are outlined here:  
ESD Program Element  
Management  
Chief coordinator  
Multi-department committee  
Employee training  
ESD Program Function  
Institute and maintain  
Organize and enforce  
Evaluate and improve  
Educate and inform  
ESD program supplies typically include: wrist- and foot-worn grounding straps; counter-top and floor antistatic  
matting; wrist strap testers; ESD video and training materials. Sources for such supplies include:  
Static Control Systems – 3M  
225-4S, 3M Center  
Charleswater  
93 Border St.  
St. Paul, MN 55144  
West Newton, MA 02165-9990  
Maxtor also offers a complete video training package, “Care and Handling of Maxtor Disk Drives.”  
Contact your Maxtor representative for details.  
4 – 12  
INSTALLATION  
Unpacking and Inspection  
Retain any packing material for reuse. Inspect the shipping container for evidence of damage in transit. Notify  
the carrier immediately in case of damage to the shipping container.  
As they are removed, inspect drives for evidence of shipping damage or loose hardware. If a drive is damaged  
(and no container damage is evident), notify Maxtor immediately for drive disposition.  
Figure 4 - 1  
Multi-pack Shipping Container  
4 – 13  
INSTALLATION  
Figure 4 - 2  
Single Pack Shipping Container (Option A)  
Figure 4 - 3  
Single Pack Shipping Container (Option B)  
Repacking  
If a Maxtor drive requires return, repack it using Maxtor packing materials, including the antistatic bag.  
Physical Installation  
Recommended Mounting Configuration  
The DiamondMax™ 2880 drive design allows greater shock tolerance than that afforded by larger, heavier  
drives. The drive may be mounted in any attitude using four size 6-32 screws with 1/8-inch maximum  
penetration and a maximum torque of 5-inch pounds. See Figure 3-1 for mounting dimensions. Allow  
adequate ventilation to the drive to ensure reliable operation.  
4 – 14  
INSTALLATION  
Before You Begin  
1
IMPORTANT – PLEASE READ !  
Please read this Installation Sheet completely before installing the Maxtor hard drive. It gives general information for installing a Maxtor hard drive in a  
typical computer system. If you don’t understand the installation steps, have a qualified computer technician install the hard drive. DO NOT use any low-level  
formatting software on this drive.  
HandlingPrecautions  
Allow the hard drive to reach room temperature BEFORE installing it in your computer system.  
Hard drives are sensitive to electrostatic discharge (ESD) damage.  
Handle the drive by its sides. DO NOT touch the printed circuit board assembly.  
NEVER drop, jar, or bump the drive.  
DON’T connect/disconnect any drive cables when the power is on.  
Tools for Installation  
The following tools are needed to complete the installation of your Maxtor hard drive:  
A small (#2) Phillips head screw driver  
Small needle-nose pliers or tweezers  
For drive capacities 8.4 GB or less, a DOS 5.0  
(or higher) or Windows 95 bootable system  
diskette  
Your computer user’s manual  
For drive capacities greater than 8.4 GB,  
a Windows 95 bootable system diskette  
Capacity Barriers  
Due to operating system limitations, DOS cannot access the full capacity of drives larger than 8.4 GB. The Microsoft Windows 95 operating system or  
equivalent (full installation), NOT a Windows 95 upgrade from DOS (Windows 3.1 or 3.11), is required to obtain the full capacity of any hard drive larger  
than 8.4 GB.  
Protecting Your Existing Data  
Have you backed up your hard disk?  
Periodic backup of important data is always a good idea. Whenever your computer is on, there is the potential for losing data on your hard drive. This is  
especially true when running disk utilities or any software that directly manipulates your files. Maxtor recommends that you make a backup copy of the  
files on any existing hard drives. If required, this data may then be copied to the Maxtor hard drive after it has been installed in your computer. Refer to your  
computer user’s manual for detailed data backup instructions.  
CapacityCalculations  
Maxtor defines one megabyte as 106 or one million bytes (1,000,000) and one gigabyte as 109 or one billion bytes (1,000,000,000).  
FDISK, CHKDSK, Windows, BIOS and hard drive manufacturers may show different capacity values for the hard drive as they use different methods and  
numbering systems to calculate hard drive capacities. The two most common numeric representations of the hard drive capacity are presented in the base 10  
(decimal) and base 2 (binary) numbering systems.  
The formula to calculate the capacity of a drive is: Cylinders * Heads * Sectors * 512  
This is a decimal number representing the total number of bytes (characters) that can be stored on the hard drive. To convert this number to binary megabytes  
(MB) or gigabytes (GB), this value must be divided by the decimal value of a binary MB or GB. The decimal equivalent of 1 MB (220) is 1,048,576 and 1 GB (230) is  
1,073,741,824.  
Example for a 3.5 GB hard drive:  
6,800 * 16 * 63 * 512 = 3,509,452,800 bytes or 3.5 GB using 106 or decimal values.  
The equivalent in binary MB is 3,509,452,800 / 1,048,576 = 3,346 MB.  
The equivalent in binary GB is 3,509,452,800 / 1,073,741,824 = 3,268 GB.  
4 – 15  
INSTALLATION  
Hardware, Software and BIOS Requirements  
2
System Hardware Requirements  
Maxtor does not recommend installing drives greater than 8.4 GB in a 486 (50 MHz or slower), 286, 386 or older systems. These systems are not designed to  
support large capacity hard drives. Even if an EIDE interface card or drive management software are used the performance and reliability of the drive in older  
systems cannot be predicted. The minimum system recommended for drives 8.4 GB and less is a 486 DX 66 MHz system. For drives larger than 8.4 GB it is  
suggested that the minimum system be a Pentium class system.  
BIOS Requirements  
Most of the systems with newer BIOS; (typically with a date of July 1994 or newer) support large capacity drives. System BIOS dated prior to September 1997  
do not provide support for drives greater than 8.4 GB. To obtain the full capacity of a drive larger than 8.4 GB either a BIOS upgrade, a BIOS enhancer card or  
the MaxBlast software (version 9.06M or newer) will be required to correctly support the drive.  
Ultra Direct Memory Access (UDMA)  
In order to utilize the drives UDMA mode it is required that the mother board or interface card have the full UDMA chip set and the UDMA drivers provided by  
the manufacturer installed on the system. If the mother board or interface card does not have this capability then UDMA will not be available on the drive  
IMPORTANT –  
Operating System Requirements for Drives Larger than 8.4 GB  
Due to limitations, DOS operating systems cannot access the full capacity of drives larger than 8.4 GB. The Windows 95 full installation operating system or  
equivalent – NOT a Windows 95 upgrade from DOS (Windows 3.1 or 3.11) – is required to obtain the full capacity of any hard drive larger than 8.4 GB. This  
means that the drive cannot be installed using a DOS operating system and then upgraded to Windows 95 or any subsequent release of this operating  
system, e.g. Windows 98.  
4 – 16  
INSTALLATION  
Hard Drive Identification  
IDE stands for Integrated Drive Electronics and EIDE is Enhanced IDE. The IDE or EIDE interface is designed to support two devices – typically hard drives – on a  
single ribbon cable through one 40 pin connector on the mother board or interface card.  
3
Some mother boards and interface cards may have a second IDE/EIDE connector to support two additional IDE devices. The IDE/EIDE interface is identified as  
a primary or secondary interface. In systems with only a single connector on the mother board or interface card, it is the primary IDE/EIDE interface and  
requires a special interface card to add a secondary IDE/EIDE interface to the system. In systems with two connectors on the mother board or interface card,  
one is identified as the primary and the other as the secondary.  
The primary interface must be used for at least one IDE device before connecting any devices to the secondary IDE interface.  
The ribbon cable used is limited to a maximum length of 18 inches (per ANSI standards) and has two or three 40 pin connectors. This cable is referred to as a  
parallel cable and IDE devices may be connected any where on the cable. One of the connectors is attached to the IDE connector on the mother board or  
interface card and the remaining connector(s) are available for the IDE devices.  
Identifying IDE Devices on the Interface  
Each IDE interface (connector) supports one or two IDE devices on the ribbon cable. Each device must be identified as either the Master or Slave device on that  
interface (cable). Each cable must have a Master before it can have a Slave device on the cable. There cannot be two Master or two Slave devices on the  
same cable.  
IDE devices use jumpers to designate the Master/Slave identification of the device. Each manufacturer may have its own jumpering scheme to identify the  
device as a Master or Slave and its relationship to other IDE devices attached to the same cable.  
Primary/Master/SlaveDefinitions  
Some hard drive manufacturers use three definitions, Primary, Master and Slave. The manufacturers which use the three definitions define “Primary” as the  
only IDE device on the interface cable; “Master” as the 1st IDE device on the interface cable; and “Slave” as the 2nd device on the interface cable. Maxtor  
uses only two definitions that of Master and Slave devices on the IDE interface. Maxtor’s “Master” definition performs both the “Primary” and “Master”  
definitions used by other hard drive manufacturers with a single jumper setting.  
JumperSettings  
A jumper is a small piece of plastic that slides over a pair of configuration pins on the drive to activate a specific function. The jumper illustration below shows  
three valid jumper settings for Maxtor hard drives – Master, Slave and Cable Select. Maxtor hard drives can be set as either a Master or a Slave device.  
There are no other jumpers to set when the Maxtor hard drive is installed on the same ribbon cable with another IDE device.  
Master Device  
Slave Device  
Cable Select  
J50 J48 J46 J44 J42  
J50 J48 J46 J44 J42  
J50 J48 J46 J44 J42  
EIDE Interface Connector J1  
Power Connector J2  
J50 – Master/Slave  
J48 – Cable Select  
J46 – 4092 Cylinder Limitation  
J44 – Factory Reserved  
J42 – Factory Reserved  
Rear View of Maxtor Hard Drive  
Master, Slave and Cable Select Settings  
Before installing the drive in the computer, you must determine how the jumpers on the Maxtor hard drive are to be set for your system based upon the use of  
the Maxtor hard drive as either a Master or Slave device. Maxtor hard drives are shipped with the Master jumper setting enabled.  
IMPORTANT: If a Maxtor hard drive is being added to a system on the same cable with an existing IDE device, it may be necessary to re-configure the  
jumpers on the existing device to insure that the system will properly recognize both devices. Information regarding the correct jumper configurations on other  
IDE devices is available in their product documentation or from the manufacturer of that device.  
4 – 17  
INSTALLATION  
Systems Using Cable Select  
IMPORTANT – Most systems do not use this feature. Unless you are sure that your computer system supports Cable Select, do not set up the drive with this  
feature enabled.  
Maxtor hard drives support Cable Select. The Cable Select method of drive identification allows the system to identify Master and Slave IDE devices based  
upon the position (connector) the IDE device is attached to on the interface (ribbon) cable.  
A special IDE cable select interface (ribbon) cable is required for systems using the Cable Select feature.  
The ribbon cable included in Maxtor kits is a standard IDE cable and cannot be used in systems that use Cable Select. Systems that use Cable Select do not  
support the standard Master/Slave definitions described above and the standard IDE interface (ribbon) cable cannot be used on these systems.  
If your system supports this feature, refer to the system user’s manual or contact the system manufacturer for specific procedures for installing hard drives. On  
Maxtor DiamondMax 2880 hard drives, Cable Select is enabled by installing a jumper on J48.  
Relationship to Other IDE Devices  
IDE devices such as a CD-ROM or tape drive also have the jumper definitions for Master and Slave. The difference between a hard drive and these devices is  
that they require special software drivers in order to communicate properly with the system. Hard drives do not require additional drivers to communicate with  
the system. Because of limitations in the software drivers provided with CD-ROMs, tape drives and other IDE devices, Maxtor does NOT recommend that a  
hard drive be a slave to a CD-ROM or other IDE devices only to another hard drive. The software drivers for non hard drive IDE devices do not provide  
adequate support for communications to a hard drive as a slave device. Maxtor recommends that hard drives be the master to any other IDE devices except  
another hard drive.  
Mounting Drive in System  
4
Turn the computer OFF, disconnect the power cord and remove the cover. Refer to the computer user’s manual for information on removing the cover.  
Each system manufacturer uses different types of cases, including desktop, mini-tower, full tower and other special configurations. As a result, there are many  
different possible mounting locations that could be used.  
In a typical system case, there are specific 3.5 inch and 5.25 inch bays available for storage devices. When a 3.5 inch mounting bay is available, mounting  
brackets and rails are not required. If a 5.25 inch mounting bay is used, mounting brackets (and possibly rails) will be required to mount the Maxtor hard drive  
in the system case. Refer to the system manufacturers user’s manual or contact the system manufacturer directly for additional information.  
NOTE: Some computer manufacturers have system cases that require custom mounting brackets and/or rails to physically mount a hard drive. If the ANSI-  
standard brackets and rails provided in the Maxtor Hard Drive Kit cannot be used in your system case, you will need to obtain custom brackets and rails from  
your system manufacturer.  
Installing 5.25-inch Mounting Brackets and Rails  
If the Maxtor hard drive is being mounted in a 5.25 inch drive bay, the following figure shows how to attach the brackets and/or rails to the drive. If the drive is  
being installed in a 3.5 inch bay which requires the use of rails, they may be installed directly on the drive without brackets.  
Installing in Drive Bay  
After the hard drive is prepared with mounting brackets/rails, if required, and the jumpers are set correctly, the drive can be mounted in a drive bay and  
secured. Note: The computer system the Maxtor hard drive is being installed in may use standard or a unique mounting and placement method. Refer to the  
computer user’s manual or contact the system manufacturer for detailed mounting instructions for that specific system.  
4 – 18  
INSTALLATION  
Attaching Interface  
and Power Cables  
5
In order for the computer to recognize that the Maxtor hard drive is in the system, the  
power cable and IDE interface cable must be properly connected.  
1
Attach an available IDE interface connector to J1 on the Maxtor hard drive. The connector on the cable provided with the Maxtor Hard Drive Kit is keyed  
and will only fit in one orientation. Do not force the connector. If the cable from the Maxtor kit is being connected to an IDE device or interface connection  
that is not keyed, the plastic plug in the connector at pin 20 may be removed.  
The striped or colored edge of the IDE interface cable indicates pin 1. Pin 1 on the IDE interface cable connector must match pin 1 on the drive IDE interface  
connector – closest to the drive power connector. It must also match pin 1 on the IDE connector on the mother board or IDE interface card. Refer to the  
system or interface card user’s manual for identification of pin 1 on their IDE interface connector.  
2
Connect an available power connector to J2 on the Maxtor hard drive. This connector is keyed and will only fit in one orientation. Do not force the  
connector.  
After attaching the IDE  
interface cable and the  
power cable to the Maxtor  
hard drive, verify that all other  
cables connected to other  
devices, the mother board or  
interface cards are correctly  
seated.  
Striped/colored edge is pin 1  
Attaching System Cables  
6
The computer system the Maxtor hard drive is being installed in will have its own cable placement and connection methodology, this means that the location  
of the IDE interface connectors on the mother board and/or interface card and the orientation of pin one is determined by the manufacturer. Also, older  
systems and interface cards may have only a single IDE interface connection, limiting the system to two IDE devices. Refer to the system or interface card user’s  
manual for detailed cable connection and orientation instructions.  
Attach the 40-pin IDE interface cable from the Maxtor hard drive to the IDE connector on the mother board or IDE interface card. Insure that the red edge of  
the ribbon cable is oriented to pin 1 on the interface.  
4 – 19  
INSTALLATION  
System Setup  
The following procedures are designed for systems using the DOS 5.0 (or higher) or Windows 95 operating systems. For other operating systems  
(e.g., Windows NT®, OS2®, UNIX®, LINUX and Novell NetWare®), refer to the operating system user’s manual for the BIOS setting and other installation  
requirements.  
7
IMPORTANT: For drives with capacities larger than 8.4 GB the full installation set for Window 95a or 95b (OSR2) or equivalent is required. Operating  
systems that do not support extended interrupt 13 cannot access or format a drive larger than 8.4 GB. This is true regardless of BIOS, mother board or  
interface card support. DOS based operating systems do not support this interrupt and are limited to a maximum drive size that they can format and access  
of 8.4 GB. It is not possible to upgrade from a DOS operating system to Windows 95 or equivalent and obtain the full capacity of a drive larger than 8.4 GB.  
Setting the BIOS (CMOS)  
The SETUP (BIOS) program identifies the system configuration information (e.g., floppy disk drives, hard disk drives, video, etc.) used to identify devices  
attached to the computer during system boot. This includes the information about what kind and how many hard drives are attached to the system.  
IMPORTANT- Please Note: Major BIOS manufacturers like AMI, Award and Phoenix provide their core BIOS programs to system board manufacturers  
and OEM’s who have the capability of making modifications to some of the descriptions and definitions to meet their unique requirements. These changes  
include, but are not limited to, how to access the BIOS, the appearance of the information on the screens and the location of parameters within the BIOS. If  
you are unsure how to access the system BIOS refer to the system or BIOS manufacturers documentation or contact the system manufacturer for the correct  
procedure to enter the BIOS setup program for your system.  
System manufacturers like Compaq, IBM, AST etc., may use their own unique proprietary BIOS definitions and configurations and will have their own unique  
methods of accessing and setting their BIOS. If you have a system that utilizes such an unique BIOS refer to the system user’s manual or contact the  
manufacturer for assistance in accessing and setting the BIOS.  
WARNING: When entering the settings for the new Maxtor hard drive, be careful not to change any of the other BIOS settings, or other parts of the system  
may not work correctly.  
BIOS (CMOS) Parameters  
In order for the computer system to recognize the new Maxtor hard drive, it is necessary to set the system BIOS with the correct information about the hard  
drive. To do this, run the system SETUP (BIOS) program. The Maxtor hard drive must be identified to the system through the BIOS and it must be registered in  
the BIOS based upon its position relative to the other IDE devices connected to the system and recorded in the BIOS.  
Most newer BIOS’ provide the descriptions of Primary Master, Primary Slave, Secondary Master and Secondary Slave (see section 2) which identify the  
device configuration and location on an IDE interface and its relationship to the other IDE devices on the same interface or ribbon cable.  
Some older BIOS versions do not use this terminology for identification and it may be necessary to refer to the system user’s manual or BIOS documentation  
to determine where the drive settings should be set in that specific BIOS. If this information is not available, then it will be necessary to contact the system  
manufacturer for the correct terminology to correctly identify the drives within the system.  
The following are the typical steps to be used to set the hard drive parameters in a BIOS:  
A
Turn the system ON. During the system start-up sequence, run the SETUP (BIOS) program or similar commands to access the system BIOS.  
Note: Newer systems will typically display a message (e.g., press DEL to Enter Setup) identifying how to access the SETUP (BIOS) program.  
Once the SETUP (BIOS) program is active, do one of the following to set the BIOS parameters for the Maxtor hard drive.  
B
1
Enter the BIOS menu where the hard drive definitions are displayed, select the correct entry (Primary Master, Primary Slave, Secondary Master or  
Secondary Slave or their equivalents) to set the parameters for the Maxtor hard drive.  
If the SETUP program provides an “AUTO DETECT” capability, use this feature to detect the Maxtor hard drive. If the SETUP program does not have  
AUTO DETECT, set the drive parameters as defined in 2 below. Typically, this feature is available for each individual IDE device. It may be necessary to  
exit the BIOS, re-boot the system and re-enter the BIOS before the AUTO DETECT operation will take effect.  
IMPORTANT After the SETUP program has detected the hard drive, verify that the Logical Block Addressing (LBA) mode is enabled for the drive - as  
not all BIOS versions set this feature during the AUTO DETECT process.  
4 – 20  
INSTALLATION  
Comment: When LBA is enabled, some BIOS programs (typically Award) will change the values of the cylinders and heads by dividing the cylinders by  
2, 4, 8 or 16 and multiplying the heads by the same value. This operation will not change the capacity of the hard drive.  
If the system correctly detects the drive and does not hang during the boot process proceed to Section 9, If the system hung during the POST proceed  
to Section 8. If Auto Detect did not find the drive and no error message was presented proceed to step 2 below.  
2
Enter the BIOS menu where the hard drive definitions are displayed and select the appropriate entry (Primary Master, Primary Slave, Secondary  
Master or Secondary Slave – or their equivalents) for the Maxtor hard drive. If the SETUP program does not provide an AUTO DETECT capability, the  
drive parameters must be set using the User Definable Type (UDT).  
Set the Cylinder, Head and Sector values with the values listed on the drive label. The drive label is located on the top cover of the drive. The fields  
LZone (Landing Zone) and WPcom (Write Pre-comp) are not used by the Maxtor hard drive. These values may be either 0 or the values set by the BIOS.  
Only the cylinder, head and sector values listed in the table must be entered. All other values may be zero (0). Set the LBA mode to enabled for this  
drive. Refer to the system user’s manual or contact the system manufacturer for information on enabling LBA.  
If the SETUP program does not provide the UDT, set the BIOS to the drive type with the largest capacity of those listed in the BIOS.  
C
After the drive parameters are entered, follow the SETUP program procedures to save the settings and exit the SETUP program. After changing BIOS  
settings, saving the values and exiting, the SETUP program should force the system to re-boot.  
If you are not sure how the UDT is defined in the BIOS, refer to the computer user’s manual or contact the system manufacturer. Companies like Compaq,  
IBM and HP use their own unique definitions and setup procedures.  
4 – 21  
INSTALLATION  
Hard Drive Preparation  
8
To finish the installation, the drive must be partitioned and formatted. Hard drive partitioning and formatting may be done with the operating system software  
or with MaxBlast installation software. Select A or B below to complete the preparation of the Maxtor hard drive.  
NOTE: Drive letter assignment is controlled by the operating system and not by the BIOS or MaxBlast. The operating system assigns drive letters to all devices  
as follows: (1) to all hard drives and their partitions; (2) to all other devices like CD-ROM’s and tape drives. When adding an additional hard drive to the system,  
the drive letters will be automatically changed by the operating system.  
A
Preparing the hard drive using the operating system software.  
IMPORTANT Due to operating system limitations, DOS operating systems cannot access the full capacity of drives larger than 8.4 GB. The Windows 95 full  
installation, not an upgrade from DOS, operating system or equivalent is required to obtain the full capacity of any drive larger than 8.4 GB.  
If the system or interface card correctly supports the Maxtor hard drive, the drive may be partitioned and formatted using the operating system software. If the  
cylinder limitation jumper (J46) is installed or the BIOS does not support the hard drive, MaxBlast installation software must be used to prepare the hard drive.  
NOTE: All versions of DOS, PC-DOS, DR-DOS and Windows 95a (FAT 16 support) have a partition size limitation of 2.1 GB. For drives larger than 2.1 GB, the  
drive must be divided into partitions that do not exceed the 2.1 GB limitation. Windows 95b (OSR2) does not have this limitation. Windows NT®, OS2®, UNIX®,  
LINUX and Novell NetWare® should not have this limitation but please refer to their documentation or contact the manufacturer to verify their support or  
limitations.  
For detailed operating system installation assistance, refer to the system manufacturers user’s manual, the operating system user’s manual or contact the  
manufacturer directly.  
B
Preparing the hard drive using MaxBlast installation software.  
1
2
Boot the system with the bootable MaxBlast software installation diskette.  
The MaxBlast installation software will load and the first screen of the program will display. Complete the information in the System Configuration  
Information table and follow the on-screen prompts to complete the hard drive installation.  
System/Drive Information  
The first time MaxBlast installation software is run, it will display information in a format similar to the System Configuration Information table below.  
Subsequent executions start at the main menu and allow the user to optionally display this information.  
S Y S TE M / D R I V E I N FO RM A T I O N  
Maxtor Hard Disk Drive  
Model Number  
Computer System  
Manufacturer  
Serial Number  
Model  
Processor (i.e., Pentium)  
Interface Card  
Speed (i.e., 90MHz)  
Manufacturer  
Model  
BIOS (CMOS/Setup)  
Manufacturer  
Version  
Date  
Other Hard Disk Drive  
Manufacturer  
Model  
Heads  
BIOS Setting: Cylinders  
Other IDE Devices  
Type (i.e., CD-ROM)  
Manufacturer  
SPT  
Model  
The information in the System Configuration table must be completed for your records. This information will be requested by the Maxtor Technical  
Assistance representative in the event that you call for assistance.  
The Maxtor hard drive model number and serial number are also located on the top cover label of the hard drive. System information should be available in  
the computer users’s manual or in the documentation for the different devices attached to the system.  
Once the information in this table is copied from the screen, continue with the installation or exit the MaxBlast installation software as shown on the screen.  
EZMAX is a menu-driven program with on-line help to guide you through the installation process.  
4 – 22  
INSTALLATION  
System Hangs During Boot  
If the system hangs during the boot process after installing the Maxtor hard drive – either before or after setting the system BIOS – the system many have a  
BIOS with a cylinder limitation. This may occur for hard drives that exceed 2.1 GB. If this happens, do the following:  
1
2
Turn the system OFF.  
Install the cylinder limitation jumper (J46) on the drive. The figure below shows the Maxtor hard drive configured as a Master or Slave device with the  
cylinder limitation jumper installed.  
IMPORTANT: When the Cylinder Limitation jumper (J46) is installed, the Maxtor hard drive must be prepared using MaxBlast installation software.  
Master Device  
Slave Device  
Cable Select  
J50 J48 J46 J44 J42  
J50 J48 J46 J44 J42  
J50 J48 J46 J44 J42  
EIDE Interface Connector J1  
Power Connector J2  
J50 – Master/Slave  
J48 – Cable Select  
J46 – 4092 Cylinder Limitation  
J44 – Factory Reserved  
J42 – Factory Reserved  
3
If the BIOS was set to AUTO DETECT, follow the instructions in Section 7 to prepare the hard drive using the MaxBlast installation software.  
If other BIOS settings were used, access the system BIOS SETUP program and set the BIOS parameters to a User Definable Type with 4,092 cylinders,  
16 heads and 63 sectors per track for the Maxtor hard drive. Then follow the instructions for setting the BIOS in Section 6 then Section 7 to prepare the  
hard drive with MaxBlast software.  
How to Obtain MaxBlast Software  
If a MaxBlast software installation diskette was not included with the hard drive, the software may be downloaded from Maxtor’s Internet home page at  
After downloading MaxBlast, perform the following steps to create a bootable diskette:  
1
If MaxBlast was downloaded to a hard drive, perform the following steps below. If MaxBlast was downloaded to a diskette, skip to step 2.  
Insert a blank 1.44 MB diskette in the A: floppy disk drive.  
Set the system DOS prompt to the hard drive letter and directory where the downloaded MaxBlast installation software is stored.  
Type “MAXBLAST,“ press the [Enter] key and follow the on-screen prompts. This will create a bootable diskette with MaxBlast software loaded and  
ready for use. Go to step 3.  
2
If the downloaded MaxBlast installation software is on a diskette, place this diskette in the A: floppy disk drive.  
Set the system to the floppy disk drive DOS prompt.  
Type “MAXBLAST,“ press the [Enter] key and follow the on-screen prompts. This will create a bootable diskette with MaxBlast software loaded  
and ready for use.  
4 – 23  

Nokia 6016i User Manual
Motorola V547 User Manual
Kenwood DPF J5030 User Manual
JVC GET0699 001A User Manual
Fujitsu MAS3735FC User Manual
Denon DN D4000 User Manual
Curtis RCD869 User Manual
Cuisinart Coffeemaker CBC 1600 User Manual
Clarion DXZ656MP User Manual
Black &amp; Decker DCM1300 User Manual