Owner’s manual
Keurig® K-Cup™ K10 MINI Plus Brewer
Important SafeguardS Safe Operation & Use
When using electrical appliances, basic
safety precautions should be followed,
including the following:
11. For best operation, plug the appliance
into its own electrical outlet on a
dedicated circuit to prevent flickering
of lights, blowing of fuses or tripping a
circuit breaker.
electrical short circuit, grounding
reduces the risk of electrical shock.
19. If the outlet is a standard 2-prong wall
outlet, it is your personal responsibility
and obligation to have it replaced with a
properly grounded 3-prong wall outlet.
20.Do not, under any circumstances, cut or
remove the third (ground) prong from
the power cord or use an adapter.
21. Consult a qualified electrician if
the grounding instructions are not
completely understood, or if doubt
exists as to whether the appliance is
properly grounded.
CAUTION: There are two sharp needles that puncture the
K-Cup® pack, one above the K-Cup® Pack Holder and the
other in the bottom of the K-Cup® Pack Holder. To avoid risk
of injury, do not put your fingers in the K-Cup® Pack
Assembly Housing.
WARNING
WARNING
KEEP ALL PLASTIC BAgS AwAY FROM CHILDREN.
THIS PRODUCT CONTAINS CHEMICALS, INCLUDINg
LEAD, wHICH IS KNOwN TO THE STATE OF CALIFORNIA TO CAUSE CANCER,
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
1. Read all instructions before using.
2. Do not touch hot surfaces. Use handles
and knobs when available.
12. Do not operate any appliance with a
damaged cord or plug or after
the appliance malfunctions or is
damaged in any manner. Contact
Keurig Customer Service to report
any malfunction of or damage to the
brewer.
13. Do not let the cord hang over the edge
of the table or counter, or touch hot
surfaces.
CAUTION: There is extremely hot water in the K-Cup® Pack Holder during
the brew process. To avoid risk of injury, do not lift the Handle or open the
K-Cup® Pack Assembly Housing during the brewing process.
3. This appliance must be properly
installed and located in accordance
with these instructions before it is used.
4. The use of accessory attachments
not recommended by the appliance
manufacturer may result in fire,
electrical shock or injury to persons.
5. Do not place on or near a hot gas or
electric burner, or in a heated oven.
6. Do not use outdoors.
CAUTION: Please always keep the brewer in its upright position to avoid
potential injury and/or damage to your brewer.
SHORT CORD INSTRUCTIONS: A short power supply cord is provided to
reduce the risk of becoming entangled in or tripping over a longer cord.
22.Do not use the appliance for other than
its intended use.
WARNING TO USERS AND PARENTS
1. DO NOT permit children to use brewer unless there is adult
supervision. Brewer dispenses very hot water.
If an extension cord is used, (1) the marked electrical rating of the cord set or
extension cord should be at least as great as the electrical rating of the
appliance; (2) the cord should be arranged so that it will not drape over the
countertop or tabletop where it can be pulled on by children or tripped over
unintentionally; and (3) the extension cord must include a 3-prong grounding plug.
14. To disconnect, press the Power Button
on the brewer to “OFF” status and then
remove the plug from the wall outlet.
7. To protect against fire, electric shock
SAvE THESE
2. SPECIAL NOTICE FOR HOT COCOA USERS:
and injury do not immerse cords, plugs, 15. Close supervision is necessary when
IMMEDIATELY AFTER USING A HOT COCOA K-CUP® PACK, RUN a Hot
Water Brew Cycle without a K-Cup® pack to avoid the possibility of
clogging the exit needle. DO NOT assume the next user will do this.
INSTRUCTIONS.
or the appliance in water or any other
liquid.
any appliance is used by or near
children.
THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.
8. Do not overfill the Cold Water Reservoir 16. Do not lift the brewer Handle while
with water.
brewing is in progress; scalding
may occur.
9. Use only water in this appliance! Do
not put any other liquids or foods in the
Water Reservoir except as instructed in
the Cleaning Instructions in this guide.
10. Turn off and unplug the brewer before
cleaning or maintenance. Allow to cool
before putting on or taking off parts
and before cleaning the appliance.
17. Always keep the Cold Water Reservoir
Lid closed unless you are refilling it.
18. This appliance is equipped with a power
cord having a grounding wire with a
grounding plug. The appliance must
be grounded using a 3-hole properly
grounded outlet. In the event of an
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT REMOVE THE
BOTTOM COVER. NO USER SERVICEABLE
PARTS ARE INSIDE. REPAIR SHOULD BE DONE
BY AUTHORIZED SERVICE PERSONNEL ONLY.
WARNING
RISK OF FIRE OR
ELECTRIC SHOCK
!
DO NOT OPEN
2
3
SeCtIon 1 Brewer Overview
table of ContentS
J
A
B
A
B
C
D
E
F
G
H
I
Water Level Guide
KEURIG® GOURMET SINGLE CUP HOME BREWING SYSTEM
K10 MINI Plus Brewer — Using Your Brewer
K
Handle
SeCTion 1—Brewer overview ..........................................................4
SeCTion 2—Helpful Hints .................................................................6
SeCTion 3—Buttons & indicators.........................................................7
K-Cup® Pack Holder Assembly
K-Cup® Pack Holder
Funnel
L
SeCTion 4—Set-Up & operation
Initial Cleansing & First Brew...........................................................8
K-Cup® Pack Assembly Housing
Drip Tray Overfill Indicator
Drip Tray Plate
M
N
D
E
SeCTion 5—Cleaning & Maintenance
C
Cleaning External Parts ..................................................................12
Cleaning the K-Cup® Pack Holder Assembly .............................. 12
Cleaning the Cold Water Reservoir................................................14
Emptying the Internal Hot Water Tank...........................................14
De-Scaling Your Brewer ..................................................................14
Storage ...............................................................................................15
Storing the Power Cord....................................................................15
F
Drip Tray
O
J
Cold Water Reservoir Lid
Cold Water Reservoir
BREW Button
G
H
K
L
M
N
O
P
SeCTion 6—Troubleshooting..........................................................16
SeCTion 7—Warranty......................................................................18
LED Indicator
Power Button
Record your Brewer Serial Number here.
I
P
Power Cord
Drip Tray Base
Removing the serial number label from the brewer will void warranty.
4
5
SeCtIon 3 Buttons & Indicators
SeCtIon 2 Helpful Hints
1. Plug Power Cord into an independent,
Grounded outlet – If the electric circuit is
overloaded with other appliances, your brewer
may not function properly.
up to 30% more ground coffee than regular
varieties) along with a brew size that’s right for
you. The less water you use, the more intense
the flavor in your cup. The more water you use,
the less intense the flavor in your cup.
10. Automatic Shut-off – As a safety feature, your
brewer will shut off automatically when it is
idle for longer than 90 seconds. Simply press
the Power Button to restart.
Power Button (does not illuminate)
Press to turn the brewer power on and off.
Add Water Indicator
Your Next Brew
When the brewing process is complete, the Add Water
Indicator light will appear. At this point you can begin
making the next beverage, or you can power off.
2. initial Cleansing Brew – Before you make your
first beverage, perform an initial cleansing
brew without inserting a K-Cup® pack.
11. Clean Your Brewer Regularly – To keep
your brewer looking and performing at its
best, be sure to clean the external and
internal components on a regular basis.
See page 12 for more information.
Use the Water Level Guide located inside the Cold
Water Reservoir to customize your brew size.
Flashing Blue — Fill the Cold Water Reservoir
with cold water until it reaches just under the rim
of the desired level – 6, 8, or 10 oz. of the Water
Level Guide.
Automatic Shut-Off
6. Brewing iced Beverages – Your iced tea and
iced coffee taste best when fresh-brewed hot
over ice. Try it by placing a tall cup filled with
ice on the Drip Tray, choose your favorite
K-Cup® pack and follow the brewing
3. one Cup at a Time – Your new brewer makes
one fresh beverage at a time. You will need to
add fresh water each time you brew. Unlike
other Keurig® brewers, the K10 MINI Plus does
not store water in the reservoir.
As a safety feature, your brewer will automatically
shut off at any stage when it is idle for longer than 90
seconds. Press the Power Button to restart. If it shut
off while the BREW Button was flashing blue, lift and
lower the Handle to reset.
12. De-Scaling – Depending on the mineral
content of the water in your area, calcium
deposits or scale may build up in your brewer.
Scale is non-toxic, but left unattended, it can
hinder brewer performance. De-scaling your
brewer helps maintain the heating element
and other internal parts of the brewer that
come in contact with water. See page 14 for
more information.
Handle Indicator
instructions on page 8. Also, look for the
“Brew Over Ice” icon on K-Cup® packs specially
crafted to brew over ice! IMPORTANT: Do not
brew into a cup made of glass. Doing so may
cause the glass to crack or break.
4. The Right Water Makes a Difference – For the
best-tasting gourmet coffee, tea or hot cocoa,
Keurig recommends using bottled or filtered
water. We do not recommend using distilled or
reverse osmosis water. Note that water quality
can vary from place to place. If you notice an
undesirable taste in your beverage (such as
chlorine or other mineral substance), we
recommend trying bottled water or water from
a filtration system. For best results, carefully
follow manufacturer’s instructions when using
any water filtration system.
Flashing Blue — The blue light flashes when the
minimum water amount of 6 oz. has been poured
into the Cold Water Reservoir. After adding your
desired amount of water (10 oz. maximum),
lower the Cold Water Reservoir Lid. The light will
continue to flash until you lift the Handle.
Drip Tray Overfill Indicator
A red float will appear when the Drip Tray is almost
full. Carefully slide Drip Tray out and empty contents
into the sink.
7. Remove K-Cup® Pack After Use – Please see
page 8 for brewing instructions.
13. Storing – When storing your brewer,
empty the Drip Tray. Follow the instructions
on page 14 for emptying the Internal Hot
Water Tank. Store your brewer upright in
a safe, dry, frost-free environment. See
page 15 for more information.
8. Brewing into a Tall Mug – To brew into a tall
mug, simply remove the Drip Tray Assembly
and place the tall mug on the Drip Tray Base.
Without the Drip Tray Assembly, however, you
do lose the benefit of the Drip Tray to contain
any excess water.
Brew Button
Flashing Blue — Indicates you are ready to brew.
Press the BREW Button.
Flashing Red — Indicates water is heating
(approximately 2 minutes).
Solid Red — Indicates brewing and dispensing of
beverage has begun.
5. Customize Your Size, Flavor & Brew – With
over 200 K-Cup® pack varieties and multiple
fill levels, your brewer provides endless
customization options – so that you can create
the size, flavor and strength of each beverage
that is perfect for you. For a strong, intense
flavor, select an Extra Bold K-Cup® pack (with
9. The Drip Tray – Any liquid overflow (from your
cup or from the Cold Water Reservoir) will be
caught in the Drip Tray. Be sure to empty the
Drip Tray when the red Drip Tray Overflow
Indicator pops up.
6
7
For accurate measuring, do not fill if the
Handle is up. In the down position it prevents
water from entering the lower heating
compartment.
SeCtIon 4 Set-Up & Operation
Initial Cleansing & First Brew
MAX
10 oz.
CAUTION: Two sharp needles are used to puncture the
K-Cup® packs. One is above the K-Cup® Pack Holder and
the other is in the bottom of the K-Cup® Pack Holder. To
avoid risk of injury, do not put your fingers inside the
K-Cup® Pack Assembly Housing.
8 oz.
BREW
CAUTION: During the brewing process, the water
gets extremely hot. To avoid risk of injury, do not
lift the Handle or open the K-Cup® Pack Assembly
Housing until brewing is complete.
6 oz.
Min
Remove all tape and cardboard.
1
2
3
4
Plug the Power Cord into an
independent, grounded outlet.
Press the Power Button. The Add Water Indicator
will flash blue.
Lift the Cold Water Reservoir Lid.
Perform an initial cleansing
brew before making your
first beverage. Follow these
instructions but do not insert
a K-Cup® pack.
Pour water anywhere within the Cold Water
Reservoir until it reaches up to the rim of your
desired fill level on the Water Level Guide
(minimum of 6 oz.). Lower the lid.
The Power Button does not illuminate.
For accurate measuring, do not fill if the
Handle is up.
Bottled or filtered water is recommended;
distilled or reverse osmosis water is not.
8
9
SECTION 4 Set-Up & Operation (continued)
Let water fully drain into brewer
before lowering the Handle.
Do noT remove foil lid or puncture K-Cup® pack.
5 Sec
2 Min
5
10
6
9
11
7
8
Lift the Handle. Water starts to drain
from the Cold Water Reservoir into
the brewer.
Place mug on the Drip Tray.
Insert the K-Cup® pack into the
K-Cup® Pack Holder.
Wait until all water has drained
(5 seconds) into the brewer
before lowering the Handle
completely.
The BREW Button will flash blue. Press the
BREW Button.
The BREW Button will flash red to
indicate that the water is heating. After
about 2 minutes, the BREW Button will
turn solid red when the beverage starts
to dispense.
Enjoy your beverage! Your brewer is ready to use
again or you can power it off.
If you want to use a taller mug,
you can slide the Drip Tray out,
but you will lose the benefit of
the tray to catch the excess
water.
Do not add a K-Cup® pack if
you are performing the initial
cleansing brew.
As a safety feature, brewer automatically
shuts off after 90 seconds.
!
CAUTION: Do not lift the Handle
If you add more than 10 oz.,
excess water goes into the
Drip Tray.
while brewing.
Remove used K-Cup® pack after brewing.
CAUTION: K-Cup® pack will be hot.
If completing the initial cleansing brew,
discard hot water into the sink. Your brewer
is ready to use again.
10
11
SeCtIon 5 Cleaning & Maintenance
Cleaning External Parts
Cleaning the K-Cup® Pack Holder Assembly
2. Separate the Funnel from the K-Cup® Pack Holder by pulling it until it
snaps free (fig. 2).
4. To replace the Funnel, just snap it back into the K-Cup®
Pack Holder (fig. 4).
IMPORTANT: Make sure the brewer is unplugged before cleaning.
K-Cup® Pack Holder Assembly parts include:
• Funnel
IMPORTANT: Make sure the brewer is unplugged before cleaning.
Regular cleaning of the brewer’s external components is recommended.
• Brewer external housing
3. Clean the Exit Needle on the bottom of the K-Cup® Pack Holder. Insert
a paper clip (fig. 3) or similar tool from below if needle becomes
clogged by coffee grinds.
fig.
4
• K-Cup® Pack Holder with Exit Needle
• Drip Tray
• Drip Tray Plate
The K-Cup® Pack Holder Assembly parts can be placed on
the top shelf of the dishwasher. Use a low temperature cycle
when cleaning.
BReWeR
fig.
fig.
2
3
• Never immerse brewer in water or other liquids.
• Clean the external housing of the brewer and other external
components with a damp, non-abrasive, lint-free cloth.
1. To remove the K-Cup® Pack
5. To replace the K-Cup® Pack Holder Assembly, align the
K-Cup® Pack Holder with the opening using the two front
ribs as a guide and snap into place from the top (fig. 5).
Holder Assembly from the brewer,
lift the Handle to open. Grasp the top
of the K-Cup® Pack Holder with one
hand. With the other hand, push up
on the bottom of the K-Cup® Pack
DRiP TRAY AnD DRiP TRAY PLATe
fig.
1
• When the red Drip Tray Overfill Indicator appears, the Drip Tray is
almost full. Carefully remove by sliding tray toward you. Empty
contents into the sink.
fig.
5
•
Inspect the Drip Tray periodically and clean with a damp, non-abrasive,
lint-free cloth.
Holder Assembly until it releases (fig. 1).
Avoid sharp needles in K-Cup®
Pack Assembly Housing. Do
not put your fingers inside the
K-Cup® Pack Assembly Housing.
Do not put the Drip Tray or the Drip Tray Plate in the dishwasher.
12
13
SECTION 5 Cleaning & Maintenance (continued)
Cleaning the Cold Water Reservoir
Emptying the Internal Hot Water Tank
De-Scaling Your Brewer (continued)
Storage
FiLL, CLeAn AnD RinSe
Step 1: First Vinegar Rinse
it is normal over time for discoloration, spotting or staining to appear in
the Cold Water Reservoir. Results will vary depending on the mineral
content of the bottled or filtered water used but will not affect the
operation of the brewer. However, be sure to clean the Cold Water
Reservoir regularly to minimize build-up.
Brewer must be powered off but plugged in.
• Lower the Cold Water Reservoir Lid.
• Place a mug on the Drip Tray.
Empty the Internal Hot Water Tank and Cold Water Reservoir before storing.
See page 14. Store your brewer in a safe, frost-free environment in an
upright position.
•
•
•
Fill the Cold Water Reservoir with 10 oz. of undiluted white vinegar.
Place the ceramic mug on the Drip Tray.
Lift the Handle, but do not add a K-Cup® pack.
• Press and hold down the BREW Button and continue to hold until all
the water is dispensed into the mug.
Storing the brewer in cold temperatures may cause any residual
condensation to freeze inside the brewer and could cause damage.
• After 5 seconds, lower the Handle.
•
•
Press the flashing blue BREW Button. It will flash red and then turn
solid red.
To access the Cold Water Reservoir, lift the lid. Remove the Water Level
Guide (fig. 6) and then clean inside the reservoir with a damp, lint-free cloth
as necessary (fig. 7).
Before using your brewer after storage, wipe the Cold Water Reservoir with a
damp, lint-free cloth and run three (3) cleaning brews (without K-Cup®
packs). See page 8 for initial cleansing brew process.
There will be a 3 to 5 second delay before water begins to dispense.
Once the vinegar is dispensed, discard hot contents into sink.
Step 2: Second Vinegar Rinse
Replace the Water Level Guide and lower the lid when finished.
•
•
•
Pour the remaining 10 oz. of vinegar into the Cold Water Reservoir.
Place the ceramic mug on the Drip Tray.
Let brewer rest at room temperature for at least 2 hours before
powering on.
De-Scaling Your Brewer
Lift the Handle, but do not add a K-Cup® pack.
The Water Level Guide is not dishwasher safe.
Calcium deposits may build up in your brewer, depending on the mineral
content of your water. Scale is non-toxic but if left unattended, it can hinder
brewer performance. De-scaling your brewer helps to maintain the heating
element and other internal parts of the brewer.
• After 5 seconds, lower the Handle.
Press the flashing blue BREW Button. It will then flash red.
When it turns solid red, power off as it starts to dispense.
•
•
Storing the Power Cord
fig.
fig.
6
7
• Allow brewer to sit for 30 minutes.
Behind the brewer is a convenient
compartment to hold the Power
Cord during transport or storage
(fig. 8).
fig.
8
•
•
Power on the brewer, lift and lower the Handle, then press
BREW Button.
Once the vinegar is dispensed, discard hot contents into sink.
The de-scaling process should be done every 3 to 6 months to ensure
optimal performance or when there are white deposits in the Cold Water
Reservoir. However, it is possible for calcium deposits to build up faster,
making it necessary to de-scale more often.
Step 3: Fresh Water Rinse
•
•
•
•
Fill the Cold Water Reservoir with 10 oz. of fresh water.
Place the ceramic mug on the Drip Tray.
Lift the Handle, but do not add a K-Cup® pack.
To begin, you will need the following:
• 20 oz. of undiluted white vinegar
• 12 oz. ceramic mug (do not use a paper cup)
• Access to a sink
Service
Lower the Handle and continue the brewing process until the
hot water is dispensed into the mug. Discard hot contents into sink.
Repeat this cleansing brew process three (3) more times to cleanse the
brewer plumbing and to remove any residual vinegar taste. The brewer
is now ready for normal use again.
Beyond these recommended cleaning and maintenance procedures, this
brewer is not user serviceable. See page 18 for warranty guidelines. For
service, please refer to the Warranty section in this guide.
•
14
15
SeCtIon 6 Troubleshooting
SiTUATion
SoLUTion
SiTUATion
SoLUTion
Brewer will not brew when used for the first time
Brewer does not have power
•
•
Make sure the Power Button is pressed. The Add Water Indicator should flash blue
after pushing the Power Button. Note that the Power Button does not illuminate.
During normal operation, the brewer will shut off when it is idle for longer than 90
seconds. Just press the Power Button to restart.
•
•
Brewer may be cold or frozen. Let brewer rest at room temperature for at least 2
hours before powering on.
Make sure the brewer has power (see previous page).
Brewer only brews a partial brew
•
•
•
•
•
Plug brewer into an independent outlet.
• Allow enough time for water in the Cold Water Reservoir to drain completely into the brewer.
• The Exit Needle may be clogged (see page 12).
•
•
•
Check to be sure that brewer is plugged in securely.
Plug into a different outlet.
Clean the K-Cup® Pack Assembly, if necessary (see page 12).
De-scale the brewer (see page 14).
If you have repeated the de-scale procedure two times and the brewer still does not
function properly, contact Customer Service.
Reset your home circuit breaker, if necessary.
If the brewer still does not operate, contact Customer Service.
BReW Button flashes red too long
•
Under normal operation, the BREW Button will flash red when the brewer is heating and
will turn solid red when brewing. If the BREW Button flashes red longer than 3 minutes,
contact Customer Service.
•
•
•
•
Under normal operation, the brewer will shut off when it is idle for longer than 90 seconds.
Just press the Power Button to restart.
If the brewer shuts off in the middle of a brew (not from power outage), contact Customer Service.
Brewer shuts off automatically
There is water in the Drip Tray
Add Water indicator does not flash blue
•
•
If the Add Water Indicator does not flash blue, make sure the brewer has power (see above).
Water may be in the Cold Water Reservoir and brewer. First, try raising the Handle to
drain all water from the Cold Water Reservoir into the brewer. If the light still does not flash,
power off and place a mug on the Drip Tray. Hold down the BREW Button and continue to
hold down until all the water is dispensed into the mug.
Remember that any liquid overflow (from your cup or the Cold Water Reservoir) will be
caught in the Drip Tray.
When the Drip Tray is almost full, the red Drip Tray Overflow Indicator will appear. Carefully
remove the Drip Tray and empty its contents into the sink.
•
If the brewer still does not operate, contact Customer Service.
Red indicator appears in Drip Tray
• This means that the Drip Tray is almost full. Carefully remove the Drip Tray and empty its
Brewer will not brew
•
•
Make sure the brewer has power (see above).
contents into the sink.
If using reverse osmosis or distilled water, the brewer may not operate correctly. See page 14 for
emptying the Internal Hot Water Tank and then use filtered or bottled water.
Press the Power Button. If the Add Water Indicator flashes blue, add water and attempt
to brew. If the brewer loses power during the brew process, the brewer may need to be
re-set when power is restored. To re-set, simply lift and lower the Handle.
Check that the minimum water level of 6 oz. has been poured into the Cold Water Reservoir.
•
Should other issues arise with your brewer, please call
Keurig Customer Service at 1.866.901.BReW (2739).
•
16
17
Scan. Click. Call!
SeCtIon 7 Warranty
Learn more and reach us quickly without leaving home.
Limited One Year Warranty
Keurig, Incorporated warrants that your brewer will be free of defects in
materials or workmanship under normal home use for one year from the date
of purchase. It is recommended that you fill out and return the warranty card
enclosed with your brewer so that your purchase information will be stored
in our system. Keurig will, at its option, repair or replace a defective brewer
without charge upon its receipt of proof of the date of purchase. If a
replacement brewer is necessary to service this warranty, the replacement
brewer may be new or reconditioned. If a replacement brewer is sent, a new
limited one year warranty will be applied to the replacement brewer.
Nor does this warranty cover damages caused by non Keurig Brewed®
K-Cup® brand packs or accessories, services performed by anyone other
than Keurig or its authorized service providers, use of parts other than
genuine Keurig® parts, or external causes such as abuse, misuse,
inappropriate power supply or acts of God.
other limitations
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS
WARRANTY, WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY
SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO
YOUR K10 MINI PLUS BREWER, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Some
states or provinces do not allow disclaimers of such implied warranties or
limitations on how long an implied warranty lasts, so the above limitation
may not apply to you depending on the state or the province of purchase.
This warranty only applies to brewers operated in the United States and
Canada. This warranty gives you specific legal rights, and you may also have
other rights that vary from state to state and, in the case of Canada, from
province to province.
Only the use of Keurig Brewed® K-Cup® brand packs and accessories will
guarantee the proper functioning and lifetime of your Keurig® brewer.
Any damage to or malfunction of your brewer resulting from the use of non
Keurig Brewed® K-Cup® brand packs and accessories may not be covered
by this warranty or may result in a service fee if the damage or malfunction is
determined to be caused by such use.
Scan here for videos about caring for your brewer!
Have questions? We’re here to help!
Scan this QR code with your smartphone for step-by-step videos on
cleaning, de-scaling and more. Or if you prefer, you can watch the videos
on your computer at bit.ly/NjTZ8W
Keurig is committed to your satisfaction. If you have questions, just give
us a call to have them answered quickly without leaving the comfort of
your home. 1.866.901.BREW (2739)
How do you obtain warranty service?
Keurig® brewers are high-quality appliances and, with proper care, are
intended to provide years of satisfying performance. However, should the
need arise for warranty servicing, simply call Keurig Customer Service at
our toll free phone number 1.866.901.BREW (2739). Please do not return your
brewer for servicing without first speaking to Keurig Customer Service to
obtain an Authorization to Return number (ATR). Keurig® brewers returned
without an ATR number will be returned to the sender without servicing.
What is not covered by the limited warranty?
THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL
DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER
INCIDENTAL COSTS AND EXPENSES RESULTING FROM ANY BREACH
OF THIS WARRANTY, EVEN IF FORESEEABLE. Some states or provinces
do not allow the exclusion or limitations of incidental or consequential
damages, so the above limitation or exclusion may not apply to you
depending on the state or province of purchase.
Keurig, Incorporated
55 Walkers Brook Drive
Reading, MA 01867
1.866.901.BREW (2739)
18
19
|