IMPRESSA Z5
Instructions for use
9/05
Fig. 1
Fig. 6
Fig. 11
Fig. 2
Fig. 7
Fig. 12
Fig. 3
Fig. 8
Fig. 13
Fig. 4
Fig. 9
Fig. 14
Fig. 5
Fig. 10
a
1
b
c
̇
Fig. 13:
Correct assembly of the
cappuccino nozzle
Make sure there is always a small gap
between the rear cappuccino nozzle
and the connection piece. This will
guarantee perfect operation of the cap-
puccino nozzle.
7
8
6
5
9
14
15
10
11
12
4a
13
2b
16b
16a
A
B
C
4b
3
2a
1
D
E
F
G
H
I
J
K
L
M
Description of the machine
1. Drip tray
2. a) Drip grate
b) Cup platform
3. Coffee grounds tray and container
4. a) One Touch Cappuccino nozzle* long spout
b) One Touch Cappuccino nozzle* short spout
5. Water tank with handle and level indicator
6. Water tank cover
7. Cover for bean tank and coffee powder tank
8. Aroma preservation cover
9. Filler funnel for pre-ground coffee
10. Control panel
11. Height-adjustable coffee spout
12. Height-adjustable hot water spout
13. Cup illumination
14. Rotary switch for setting the grinding degree
15. Power switch
16. a) Vacuum milk container
b) Stainless steel vacuum milk container
* hereinafter referred to as cappuccino nozzle
A ON / OFF key
B Rotary Switch
C Maintenance key
D Milk key
E Cappuccino key
F Special Coffee key
G Hot Water key
H Text display
I
J
Graphics display
1 ESPRESSO key
K 2 ESPRESSOS key
L 1 COFFEE key
M 2 COFFEES key
Contents
1. Safety information ..............................................page
7
7
7
7
7
8
8
8
8
8
8
9
9
9
15. Programming.....................................................page 20
15.1 Programming the filter...............................page 20
15.2 Programming your machine to the correct
1.1
1.2
Warning..................................................page
Precautions..............................................page
2. Preparing the IMPRESSA Z5 ...............................page
water hardness (only with FILTER NO)..........page 20
2.1
2.2
2.3
2.4
2.5
2.6
Check supply voltage..................................page
Check electrical fuse..................................page
Fill water tank .........................................page
Fill coffee beans .......................................page
Adjusting the grinding gear .........................page
Vacuum milk container...............................page
15.3 Maintenance ............................................page 20
15.4 Programming the temperature for coffee,
espresso, cappuccino and special coffee ..........page 20
15.5 Programming the coffe strength ...................page 21
15.6 Cappuccino programming............................page 22
15.7 Programming the milk ...............................page 22
15.8 Save energy .............................................page 23
15.9 Setting the time........................................page 24
15.10 Programming the automatic switch-on time.....page 25
15.11 Programming the automatic switch-off time ....page 25
15.12 Information .............................................page 26
15.13 Renaming................................................page 27
15.14 Programming the language..........................page 28
15.15 Programming the display ............................page 28
16. Maintenance......................................................page 29
16.1 Filling the water tank ................................page 29
16.2 Emptying the coffee gronds .........................page 30
16.3 Emptying the drip tray ...............................page 30
16.4 Drip tray missing ......................................page 30
16.5 Grounds container missing...........................page 30
16.6 Filling the bean tank..................................page 31
16.7 Aroma preservation cover missing.................page 31
16.8 Removing stones from the grinding gear.........page 31
16.9 Changing the filter ....................................page 31
16.10 Information about cleaning cycle ..................page 31
16.11 Information about decalcify.........................page 32
16.12 Emptying the system..................................page 32
17. Cleaning ...........................................................page 32
18. Decalcifying ......................................................page 33
19. Disposal ...........................................................page 35
20. Tips for perfect coffee..........................................page 35
21. Problems ..........................................................page 36
22. Legal information ...............................................page 37
23. Technical Data...................................................page 37
2.6.1 Vacuum milk container (16a).......................page
2.6.2 Stainless steel vacuum milk container (16b)....page
2.7
Power switch............................................page
3. First use...........................................................page
3.1
Cup illumination .......................................page 10
4. Adjusting your machine to the water hardness...........page 10
5. Using the CLARIS plus filter cartridge....................page 11
5.1
5.2
Installing the filter ....................................page 11
Changing the filter ....................................page 12
6. Rinsing the machine ............................................page 13
7. Making coffee (1 espresso, 2 espressos, 1 coffee,
2 coffees)..........................................................page 13
8. Making special coffee ..........................................page 13
9. Cappuccino .......................................................page 14
9.1
9.2
9.3
9.4
Making cappuccino....................................page 14
Cappuccino rinsing cycle.............................page 14
Cappuccino cleaning cycle ...........................page 15
Cleaning the cappuccino nozzle ....................page 16
10. Making hot milk.................................................page 16
11. Making hot water ...............................................page 16
12. Brewing coffee using pre-ground coffee powder .........page 17
13. Switching the IMPRESSA off ...............................page 17
14. Settings............................................................page 18
14.1 Setting the amount of water for coffee,
espresso (1 or 2 cups) and special coffee ........page 18
14.2 Cappuccino setting ....................................page 18
14.3 Milk setting .............................................page 19
14.4 Setting the amount of hot water ...................page 19
6
Ⅲ Never use a defective coffee machine or a machine with a
defective mains cable.
Introduction
Thank you for purchasing the IMPRESSA Z5. To ensure perfect
functioning of your IMPRESSA, carefully read this operating
manual and keep it for future reference.
Ⅲ Never immerse the coffee machine in water.
1.2 Precautions
Should you need more information or if you encounter particular
problems not specified in these operating instructions in sufficient
detail, either contact us directly or contact your local authorized
dealer.
You can download other languages from the JURA website at
Ⅲ Never expose the coffee machine to weather (rain, snow, frost),
never touch the machine when your hands are wet.
E
Ⅲ Place the IMPRESSA on a firm, level base that is resistant to
any water that may leak. Never stand on hot or warm surfaces
(oven hobs). Keep out of the reach of children.
Ⅲ If you don’t use the machine for a longer time (holidays, etc.)
always disconnect the mains cable.
You will also find useful tips on operation and maintenance
Don’t forget to check out the Knowledge Builder our ani-
mated operating instructions. LEO, our assistant, will take
you through all the functions.
Ⅲ Always disconnect mains cable before cleaning the machine.
Ⅲ When disconnecting the mains cable never pull on the mains
cable or the machine itself.
Ⅲ Never repair or open the coffee machine yourself. Any repairs
may only be carried out by authorized service shops using ori-
ginal spare parts and accessories.
If you have chosen the special chrome version of the
IMPRESSA Z5, your machine is equipped with a stainless
steel vacuum milk container (Fig. 16b) and an elegant cup
platform (Fig. 2b). Also, the IMPRESSA Z5 Chrome is
delivered with a microfibre cloth for cleaning the high-class
chrome front.
Ⅲ The coffee machine is connected to mains supply via a mains
cable. Make sure nobody can trip over the mains cable. Make
sure children and pets cannot reach the machine
We recommend that you wash the microfibre cloth with
items of similar colour.
Ⅲ Never put the coffee machine or individual parts of it into a
dishwasher.
Ⅲ Make sure to install the machine at a place with sufficient air
circulation, to prevent overheating of the machine.
1. Safety information
1.1 Warning
2. Preparing the IMPRESSA Z5
2.1 Check supply voltage
Ⅲ Children do not realize the dangers involved in using electric
appliances, for this reason always keep an eye on children when
they use electric appliances.
The IMPRESSA Z5 is preset in the factory to the correct mains
voltage. Check if your local mains supply voltage complies with
the information given on the type plate on the underside of the
IMPRESSA.
Ⅲ The coffee machine may only be used by instructed persons.
7
a fine grinding degree Ǟ for bright roasts
a coarse degree for dark roasts
2.2 Check electrical fuse
Ǟ
The IMPRESSA Z5 is designed for an electric current of 10
amperes. Check if the electrical fuse has sufficient capacity.
The grinding degree may only be adjusted while the grinding
gear is running.
2.3 Fill water tank
Ⅲ Open the bean tank cover (7).
Only use fresh, cold water. Never fill in milk, mineral water
or other liquids.
Ⅲ To adjust the grinding degree, turn the Rotary Switch (14) to the
required position.
Ⅲ Remove the water tank and rinse it with cold tap water
thoroughly (Fig. 1).
Ⅲ There are two options:
the narrower the bar, the finer the grind
the broader the bar, the coarser the grind
Ⅲ Then fill the water tank and reinstall it. Make sure to install the
tank properly, it must engage audibly.
2.6 Vacuum milk container
2.4 Fill coffee beans
Ⅲ The vacuum milk container and the lid are NOT dishwasher safe
To ensure that your machine will work perfectly for a long
time and to avoid damage, please note that the grinding gear
of your JURA coffee machine is not suitable for coffee beans
which were treated, during or after roasting, with additives
(e.g. sugar). Such coffee blends may damage the grinding
gear. Any repair costs resulting from the use of such blends
are not covered by warranty.
Ⅲ Wash out the vacuum milk container (16a/16b) thoroughly
before you use it for the first time.
Ⅲ Fill the milk container with cool, fresh milk.
Ⅲ Always make sure there is enough milk in the vacuum milk con-
tainer before you froth milk or make cappuccino.
Ⅲ If filled with refrigerated milk, the vacuum milk container will
keep mil cool for about 8 hours.
Ⅲ Open the bean tank cover (7) and remove the aroma preser-
vation cover (8).
Ⅲ Please do not fill ice cubes into the vacuum milk container since
these could damage its coating.
Ⅲ Remove any dirt or foreign matter from the bean tank.
Ⅲ Keep the vacuum milk container away from hot stove tops etc.
Ⅲ Fill coffee beans into the bean tank (Fig. 2), replace the aroma
preservation cover (8), make sure the rounded edges are pointing
outwards, and close the lid.
Ⅲ The vacuum milk container may be damaged if dropped.
2.6.1 Vacuum milk container (16a)
2.5 Adjusting the grinding gear
Ⅲ Never use shapr or pointed objects in the milk container since
these could damage its coating.
You can adjust the grinding gear to the roast of your coffee. We
recommend
8
2.6.2 Stainless steel vacuum milk container (16b)
Ⅲ Switch the machine on using the ON/OFF key
of the ON/OFF key goes off.
(A). The light
Ⅲ Always clean the stainless steel vacuum milk container after you
have used it. Rinse it with warm water, and with some detergent
if necessery Remove the riser tube inside the milk container as
well as the hose connection on the outside and give these parts
including the lid a good rinse with clear water. Never use scour-
ing agents, bleach, solvents or abrasive pads for cleaning. Leave
the vacuum milk container OPEN if it’s not being used.
Ⅲ
Ⅲ
LANGUAGE
ENGLISH
Ⅲ Turn the Rotary Switch (B) until the required language is dis-
played.
E
Ⅲ Example:
Ⅲ
Ⅲ
LANGUAGE
ENGLISH
Ⅲ The stainless steel vacuum milk container is supplied with a hose
set consisting of a 120 mm hose (fitted on both ends with a con-
nection nipple) and a 360 mm hose. With the longer hose the
container can be placed further away from the machine. You can
also cut it to make 3 spare hoses each with a length of 120 mm.
Ⅲ Confirm the selected language by pressing the Rotary Switch
(B).
Ⅲ
Ⅲ
Ⅲ
Ⅲ
CONFIRMED
Ⅲ Please note that in order to fasten the suction tube on the lid the
(transparent) rubber seal first has to be inserted into the opening
as far as the stop. Then insert the suction tube into the rubber
seal as far as the stop.
√
TIME
HOURS
—:—
Too little milk in the container may cause the milk to squirt
out of the nozzle.
Ⅲ To set the hours, turn the Rotary Switch (B)
Ⅲ
Ⅲ
TIME
HOURS
12:00
2.7 Power switch
Actuate the power switch (15) on your IMPRESSA Z5 be-
fore using the machine for the first time.
Ⅲ Press the Rotary Switch (B) to confirm the hours and to activate
the minutes.
Ⅲ
Ⅲ
TIME
We recommend that you switch off your IMPRESSA Z5
with the power switch (15) if you intend not to use the
machine for longer periods of time (e.g.during holidays)
MINUTES
12:00
Ⅲ To set the minutes, turn the Rotary Switch (B).
Ⅲ
Ⅲ
TIME
3. First use
MINUTES
12:45
Ⅲ Press the power switch (15) at the bottom left of your IMPRES-
SA (Fig. 3)
Ⅲ Confirm the minutes by pressing the Rotary Switch (B).
Ⅲ The ON/OFF key lights up
(A) to indicate that the machine
has been switched on with the power switch.
9
After putting the IMPRESSA into operation for the first
time, do not disconnect it from the mains for at least 24
hours to ensure it is in perfect operating condition. There-
fore, do not turn the machine off using the power switch dur-
ing this time!
Ⅲ
Ⅲ
Ⅲ
Ⅲ
CONFIRMED
√
PRESS MAINTENANCE
Ⅲ Maintenance key
(C) lights up.
If FILL BEANS appears on the display, press one of the
coffee product keys again. The mill is not yet completely
filled with coffee beans.
Ⅲ Place a cup each under the height-adjustable coffee spout (12)
and the cappuccino nozzle (4) and press the maintenance key
(C).
Ⅲ
Ⅲ
SYSTEM FILLS
For a perfect frothing result, adjust the coffee spout (11) to
the size of your cup (Fig. 4).
Ⅲ The system now fills up automatically. While it is doing so, the
maintenance key flashes. (A little water will leak from the cap-
puccino nozzle (4), then from the hot water spout (12).
3.1 Cup illumination
The cup illumination puts your coffee in a perfect light, making it
a treat for the eyes as well.
When you switch on the IMPRESSA or press any key, the cup
illumination is activated for 1 minute.
Ⅲ
Ⅲ
Ⅲ
Ⅲ
Ⅲ
Ⅲ
WELCOME TO
JURA
UNIT IS HEATING
4. Adjusting your machine to the water hardness
PRESS MAINTENANCE
The IMPRESSA heats up water. As a result, calcification
occurs during normal use, and it is indicated automatically.
The IMPRESSA must therefore be adjusted to the hardness
of the water used. Use the supplied test sticks to determine
the water hardness or contact your local waterworks.
Ⅲ Place a cup under the height-adjustable coffee spout (11).
Ⅲ Press the maintenance key (C).
Ⅲ
Ⅲ
RINSING
1° German hardness is equivalent to 1.79° French hardness.
Ⅲ Now the water lines are flushed with fresh water. A little water
will leak from the coffee spout (11).
Ⅲ
Ⅲ
COFFEE READY
The water hardness programming step is no longer displayed
if the filter is activated.
Ⅲ You can now make the machine dispense a product of your
choice by pressing the corresponding key.
The IMPRESSA is preset to 16°e. This setting can be changed. To
do so, proceed as follows:
10
5. Using the CLARIS plus filter cartridge
Ⅲ
Ⅲ
COFFEE READY
When using the CLARIS plus filter cartridge correctly,
decalcifying your IMPRESSA will no longer be necessary.
For more information on the CLARIS plus filter cartridge
refer to brochure “CLARIS plus. Hard on limescale. Gentle
on your coffee machine.”
Ⅲ Press the Rotary Switch (B) until you hear an acoustic signal.
Ⅲ
Ⅲ
FILTER
NO
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
E
played:
5.1 Installing the filter
Ⅲ
Ⅲ
HARDNESS
16°dH
Ⅲ Press the Rotary Switch (B) until you hear an acoustic signal.
Ⅲ
Ⅲ
FILTER
NO
Ⅲ Now press the Rotary Switch (B) to start programming.
Ⅲ
Ⅲ
HARDNESS
16°dH
Ⅲ Now press the Rotary Switch (B) to start programming.
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
played:
Ⅲ Now turn the Rotary Switch until the correct water hardness is
set.
Ⅲ
Ⅲ
FILTER
YES
Ⅲ
Ⅲ
HARDNESS
20°dH (example)
Ⅲ Confirm your setting by pressing the Rotary Switch (B).
Ⅲ Confirm the selected setting by pressing the Rotary Switch (B).
Ⅲ
Ⅲ
Ⅲ
Ⅲ
CONFIRMED
√
Ⅲ
Ⅲ
Ⅲ
Ⅲ
CONFIRMED
√
INSERT FILTER
HARDNESS
PRESS BUTTON
20°dH (example)
Ⅲ Remove the water tank from the IMPRESSA. Empty out any
remaining water. Fold up the cartridge holder (Fig.6). Attach the
extension piece (contained in the Welcome Pack) to the top of
the CLARIS plus filter cartridge. Now insert the filter cartridge
in the water tank, applying gentle pressure (Fig. 6)
Ⅲ Now turn the Rotary Switch (B) until the following message is
displayed:
Ⅲ
Ⅲ
EXIT
Ⅲ Now press the Rotary Switch (B) to leave the programming
Ⅲ Close the cartridge holder until it engages audibly.
mode.
Ⅲ Fill the water tank with cold, fresh tap water and place it back
Ⅲ
Ⅲ
COFFEE READY
into the machine.
11
Ⅲ Place a sufficiently large receptacle (min. 0.5 litres) under the
cappuccino nozzle (4). We recommend attaching the short spout
(4b).
Ⅲ
Ⅲ
INSERT FILTER
PRESS BUTTON
Ⅲ Remove the water tank from the IMPRESSA. Empty out any
remaining water. Fold up the cartridge holder (Fig.6). Attach the
extension piece to the top of the CLARIS plus filter cartridge.
Now insert the filter cartridge in the water tank, applying gentle
pressure (Fig. 6).
Ⅲ Press the maintenance key
(C) to start rinsing the filter.
Ⅲ
Ⅲ
FILTER RINS
Ⅲ Filter rinsing stops automatically.
Ⅲ Close the cartridge holder until it engages audibly.
Ⅲ
Ⅲ
Ⅲ
Ⅲ
UNIT IS HEATING
Ⅲ Fill the water tank with cold, fresh tap water and place it back
into the machine.
COFFEE READY
Ⅲ Place a sufficiently large receptacle (min. 0.5 litres) under the
cappuccino nozzle (4). We recommend attaching the short spout
(4b).
You have now activated the filter. The programming step for
adjusting your machine to the correct water hardness is
therefore no longer displayed.
Ⅲ Press the maintenance key
(C) to start rinsing the filter.
Ⅲ
Ⅲ
FILTER RINS
The water might be slightly discoloured (no hazard to
health).
You can interrupt the filter rinsing cycle (e.g. to empty the
receptacle). To do so, press a key of your choice.
Ⅲ Filter rinsing stops automatically.
Ⅲ
Ⅲ
Ⅲ
Ⅲ
UNIT IS HEATING
COFFEE READY
5.2 Changing the filter
After drawing off approx. 50 litres, the filter cartridge will be
used up. A message requesting you to replace the filter will
appear on the display. The scale on the cartridge holder in
the water tank will tell you how much longer you can use the
CLARIS plus filters.
You can also trigger a change of filter manually from the
maintenance menu at any point in time (only if the filter has
been activated) – see Chapter 15.3
The water might be slightly discoloured (no hazard to
health).
Ⅲ
Ⅲ
COFFEE READY
FILTER-CHANGE
You can interrupt the filter rinsing cycle (e.g. to empty the
receptacle). To do so, press a key of your choice.
Ⅲ The maintenance key
(C) lights up. Press the maintenance
key.
12
Ⅲ The coffee brewing process stops automatically as soon as the
set amount of water has run through.
6. Rinsing the machine
If the coffee machine is switched off and has cooled down,
you will be prompted to start a rinsing cycle when switching
the machine back on. The machine automatically performs a
rinsing cycle when you switch it off.
Ⅲ
Ⅲ
COFFEE READY
To stop the brewing process prematurely, press any of the
draw-off keys.
Ⅲ
Ⅲ
PRESS MAINTENANCE
E
You can pre-select the strength of your coffee when the ma-
Ⅲ Place a cup under the height-adjustable coffee spout (11).
Ⅲ Press the maintenance key (C).
chine is ready to brew (
PLEASE SELECT) To do
so, turn the Rotary Switch (B) until the display indicates the
desired coffee strength and then press a coffee key of your
Ⅲ
Ⅲ
Ⅲ
Ⅲ
RINSING
choice
,
,
,
.
COFFEE READY
You can change the amount of water to be used while the
machine is brewing coffee. To do so, turn the Rotary Switch
(B) until the display indicates the required amount (ML). The
amount of water can be selected in increments of 5 ML.
You can also trigger a rinsing cycle manually from the main-
tenance menu at any point in time (see Chapter 15.3).
The amounts given in ML are approximate values and may
vary from the effective quantity.
With manually triggered rinsing, all the spouts that were
used are rinsed.
8. Making special coffee
7. Making coffee
Ⅲ
Ⅲ
COFFEE READY
(1 espresso, 2 espressos, 1 coffee, 2 coffees)
Ⅲ
Ⅲ
COFFEE READY
Ⅲ Place 1 cup under the cappuccino nozzle (4) and press the
Special Coffee key . The pre-brewing process (I.P.B.A.S.)
moistens the coffee powder, briefly interrupts the flow of hot
water and then begins with the actual brewing process.
Ⅲ Place 1 or 2 cups (as required) under the adjustable coffee spout
(11) and press the corresponding symbol . The
,
,
,
pre-brewing process (I.P.B.A.S.) moistens the coffee powder,
briefly interrupts the flow of hot water and then begins with the
actual brewing process.
Ⅲ
Ⅲ
SPECIAL CUP
MILD (example)
Ⅲ The coffee brewing process stops automatically as soon as the
Ⅲ
Ⅲ
1 ESPRESSO (example)
STRONG (example)
set amount of water has run through.
13
Ⅲ
Ⅲ
COFFEE READY
Ⅲ
Ⅲ
CAPPUCCINO
MILK
Ⅲ The machine stops drawing milk automatically as soon as the set
amount of milk (in SEC) has been used.
To stop the brewing process prematurely, press any of the
product keys.
Ⅲ
Ⅲ
CAPPUCCINO
NORMAL (example)
You can pre-select the strength of your coffee when the ma-
chine is ready to brew (
PLEASE SELECT). To
Ⅲ The coffee brewing process stops automatically as soon as the
do so, turn the Rotary Switch (B) until the display indicates
the desired coffee strength and then press the coffee key of
your choice (key F for special coffee).
set amount of coffee has been made.
Ⅲ
Ⅲ
COFFEE READY
You can change the amount of water while the machine is
brewing coffee. To do so, turn the Rotary Switch (B) until
the display indicates the required amount (ML). The amount
of water can be selected in increments of 5 ML.
To stop the frothing or the brewing process prematurely,
press the Cappuccino key
again.
You can pre-select the strength of your coffee when the ma-
chine is ready to brew ( PLEASE SELECT). To
do so, turn the Rotary Switch (B) until the display indicates
the desired coffee strength and then press the key of your
choice (E for cappuccino).
The amounts given in ML are approximate values and may
vary from the effective quantity.
9. Cappuccino
You can change the amount of milk and the amount of water
while the machine is brewing coffee. To do so, turn the
Rotary Switch (B) until the display indicates the required
SEC (during frothing) or ML (during coffee brewing).
9.1 Making cappuccino
Ⅲ
Ⅲ
COFFEE READY
Ⅲ Take the milk hose out of the Welcome Pack. (We recommend
using the short hose with the vacuum milk container and the
long hose with a milk carton). Connect the hose with the suction
pipe projecting from the vacuum milk container. Then attach the
other end of the hose to the cappuccino nozzle (Fig. 8).
The amounts given in ML are approximate values and may
vary from the effective quantity.
9.2 Cappuccino rinsing cycle
Ⅲ Turn the selector switch (1, Fig. 9) to the milk frothing range
(a, Fig. 9).
10 min. after having made cappuccino or frothed milk, a
message on the display of your IMPRESSA will prompt you
to run a cappuccino rinsing cycle.
Ⅲ Place 1 cup under the cappuccino nozzle and press the Cappuc-
cino key
.
Ⅲ
COFFEE READY
14
Ⅲ
CAPPU RINSE
Ⅲ
NO or YES
Ⅲ Place a sufficiently large receptacle (ca. 0.5 litres) under the cap-
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
puccino nozzle (4).
played:
Ⅲ Turn the selector switch (1, Fig. 9) to the steam range (c, Fig. 9).
Ⅲ
Ⅲ
MAINTENANCE
Ⅲ Press the maintenance key
(C) to start the cappuccino rinsing
cycle.
Ⅲ Now press the Rotary Switch (B) to start the maintenance menu.
E
Ⅲ
Ⅲ
Ⅲ
Ⅲ
CAPPUCCINO
RINSING
Ⅲ
Ⅲ
RINSE UNIT
COFFEE READY
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
played:
Ⅲ
Ⅲ
CAPPUCCINO CLEANING
You can also trigger a cappuccino rinsing cycle manually
from the maintenance menu at any point in time (see Chapter
15.3).
Ⅲ Place a sufficiently large receptacle (ca. 0.5 litres) under the cap-
puccino nozzle (4).
Ⅲ Confirm by pressing the Rotary Switch (B).
9.3 Cappuccino cleaning cycle
Ⅲ
Ⅲ
CLEANER FOR CAPPUCCINO
PRESS BUTTON
We recommend running the cappuccino cleaning cycle daily
if you make cappuccino or frothed milk.
Ⅲ Fill a receptacle with approx. 250 ml of fresh water and add 1
capful of cappuccino cleaning agent. Dip the milk hose into the
solution (Fig.10).
Your IMPRESSA will not prompt you to run the cappuccino
cleaning cycle. You need to activate the cappuccino cleaning
cycle manually from the maintenance menu.
Ⅲ Make sure the selector switch (1, Fig. 9) is not set to “Steam” (c,
Fig. 9).
Please contact your authorized dealer for a JURA cappuccino
cleaner that is suitable specifically for the cappuccino clean-
ing program of your IMPRESSA. Please note that the use of
unsuitable cleaning agents may cause damage to your
machine and could leave unfavourable residues in the water.
Ⅲ Press the maintenance key
(C) to start the cleaning cycle.
Ⅲ
Ⅲ
Ⅲ
Ⅲ
MACHINE IS CLEANING
WATER FOR CAPPUCCINO
PRESS BUTTON
Ⅲ
Ⅲ
COFFEE READY
Ⅲ Fill a receptacle with fresh water and dip the milk hose into it
(Fig. 10).
Ⅲ Press the Rotary Switch (B) until you hear an acoustic signal.
FILTER
Ⅲ Press the maintenance key
(C).
Ⅲ
15
Ⅲ
Ⅲ
Ⅲ
Ⅲ
MACHINE IS CLEANING
COFFEE READY
Ⅲ
Ⅲ
COFFEE READY
To stop the machine dispensing milk prematurely, press any
of the product keys.
10 min. after having made cappuccino or frothed milk, your
IMPRESSA will prompt you to run a cappuccino rinsing
cycle. The prompt appears on the display (see Chapter 9.2
Cappuccino rinsing cycle).
9.4 Cleaning the cappuccino nozzle
Despite the cappuccino cleaning cycle, you should regularly
disassemble the cappuccino nozzle and rinse it under running
water.
You can change the amount of milk set while the machine is
dispensing milk. To do so, turn the Rotary Switch (B) until
the display indicates the required SEC.
Ⅲ Remove the cappuccino nozzle from the IMPRESSA and take it
apart as shown in Fig. 11.
Ⅲ Thoroughly rinse all the parts of the nozzle under running water.
We recommend running the cappuccino cleaning cycle daily
if you make cappuccino or frothed milk (see Chapter 9.3
Cappuccino cleaning cycle).
Ⅲ Re-assemble the cappuccino nozzle and attach it to your
IMPRESSA.
10. Making hot milk
11. Making hot water
Ⅲ
Ⅲ
COFFEE READY
Ⅲ
Ⅲ
COFFEE READY
Ⅲ Take the milk hose out of the Welcome Pack. (We recommend
using the short hose with the vacuum milk container and the
long hose with a milk carton). Connect the hose with the suction
pipe projecting from the vacuum milk container. Then attach the
other end of the hose to the cappuccino nozzle (Fig. 8).
Ⅲ Place 1 cup or 1 glass under the height-adjustable hot water
spout (12) and press the Hot Water key
.
Ⅲ
Ⅲ
HOT WATER
PORTION
Ⅲ Turn the selector switch (1, Fig. 9) to “Milk” (b, Fig. 9).
Ⅲ The machine stops dispensing water automatically as soon as the
programmed amount of water has been dispensed.
Ⅲ Place 1 cup or 1 glass under the cappuccino nozzle (4) and press
the Milk key
.
Ⅲ
Ⅲ
COFFEE READY
Ⅲ
Ⅲ
MILK
20 SEC (example)
To stop the machine dispensing hot water prematurely, press
any of the product keys.
Ⅲ The machine stops dispensing milk automatically as soon as the
set amount of milk (in SEC) has been dispensed.
16
You can change the amount of water set while the machine
is dispensing hot water. To do so, turn the Rotary Switch (B)
until the display indicates the required amount (ML). The
amount of water can be selected in increments of 5 ML.
Ⅲ
Ⅲ
COFFEE READY
To stop the brewing process prematurely, press any of the
keys.
The amounts given in ML are approximate values and may
vary from the effective quantity.
We recommend always using powder from fresh coffee
beans or pre-ground, vacuum-packed coffee. Never fill in
more than 2 scoops of powder. The filler funnel is no storage
tank. Make sure the coffee powder you use is not too fine.
This may block the system and cause the coffee only to drip
out of the coffee spout.
E
12. Brewing coffee using pre-ground coffee powder
Never use water-soluble instant coffee.
Ⅲ
Ⅲ
COFFEE READY
If you have used too little powder, the display will indicate
“NOT ENOUGH”. Your IMPRESSA will stop the process
and return to “COFFEE READY”.
Ⅲ Place 1 or 2 cups (as required) under the height-adjustable coffee
spout (11).
You can also make special coffee or cappuccino using pre-
ground coffee powder.
Ⅲ Open the lid of the filler funnel for pre-ground coffee (9). It is
under the bean tank cover (7).
Ⅲ
Ⅲ
PRE-GROUND
FILL POWDER
You can change the amount of water set while the machine
is brewing coffee. To do so, turn the Rotary Switch (B) until
the display indicates the required amount (ML). The amount
of water can be selected in increments of 5 ML.
Ⅲ Fill 1 or 2 level scoops of pre-ground coffee into the filler funnel
for pre-ground coffee (9) (Fig. 7) and close the lid.
Ⅲ
Ⅲ
PRE-GROUND
The amounts given in ML are approximate values and may
vary from the effective quantity.
COFFEE READY
Ⅲ Then press a key of your choice
,
,
,
,
,
. The
machine will brew the coffee with the amount of water pre-
selected for it.
13. Switching the IMPRESSA off
When you switch the machine off, all the spouts that were used
will be rinsed. Therefore, please make sure to place suitable recep-
tacles under the spouts.
Ⅲ
Ⅲ
PRE-GROUND
Ⅲ The coffee brewing process stops automatically as soon as the
set amount of coffee has been made.
Ⅲ
Ⅲ
COFFEE READY
17
Ⅲ
Ⅲ
1 COFFEE (example)
NORMAL (example)
Ⅲ Switch the IMPRESSA off with the ON / OFF switch
(A).
Ⅲ
Ⅲ
GOODBYE
Ⅲ The coffee will be brewed. Keep on holding the key down until
the following message is displayed:
Ⅲ The coffee spout is rinsing.
Ⅲ
Ⅲ
ENOUGH ?
Ⅲ
Ⅲ
RINSE LEFT SPOUT
PRESS BUTTON
PRESS BUTTON
Ⅲ When you have made as much coffee as you wanted, briefly
press the key once more.
Ⅲ Press the maintenance key
(C) to continue rinsing.
Ⅲ
Ⅲ
GOODBYE
Ⅲ
Ⅲ
CONFIRMED
√
Ⅲ The amount of coffee made has now been programmed for the
selected type of coffee.
When switching the machine off, there may be a hissing
sound. This is due to a normal process being performed by
the system.
Ⅲ
Ⅲ
COFFEE READY
It is recommended to switch off the machine with the power
switch if you intend not to use your IMPRESSA for a longer
time.
14.2 Cappuccino setting
The system’s basic settings include pre-defined amounts of water
(100 ml) and milk (15 sec.). However, these amounts can be
modified as required.
14. Settings
14.1 Setting the amount of water for coffee,
espresso (1 and 2 cups) and special coffee
Ⅲ
Ⅲ
COFFEE READY
The system’s basic settings include pre-defined amounts of water
(coffee 130 ml, espresso 60 ml, 2 coffees 260 ml, 2 espressos
120 ml, special coffee 145 ml). However, these can be modified as
required.
Ⅲ Place a cup under the cappuccino nozzle (4).
Ⅲ Press the Cappuccino key
and hold it down until the follow-
ing message appears:
Ⅲ
Ⅲ
CAPPUCCINO
Ⅲ
Ⅲ
COFFEE READY
NORMAL (example)
Ⅲ The cappuccino will be brewed. Keep on holding the key
Ⅲ Place a cup under the respective coffee spout (17).
down until the following message is displayed:
Ⅲ Press the product key to be programmed and hold it down until
the following message appears:
Ⅲ
Ⅲ
ENOUGH MILK
PRESS BUTTON
18
Ⅲ When the machine has dispensed as much milk as you wanted,
briefly press the key once more.
CONFIRMED
Ⅲ When the machine has dispensed as much milk as you wanted,
briefly press the key once more.
CONFIRMED
Ⅲ
Ⅲ
Ⅲ
Ⅲ
√
√
Ⅲ The amount of milk to be dispensed is now programmed.
Ⅲ The amount of milk to be used is now programmed.
Ⅲ
Ⅲ
ENOUGH ?
You can also set the amount of milk in the programming
mode (see Chapter 15.7)
E
PRESS BUTTON
Ⅲ When you have made as much coffee as you wanted, briefly
press the key once more.
14.4 Setting the amount of hot water
Ⅲ
Ⅲ
CONFIRMED
The system’s basic settings include a pre-defined amount of water
(225 ml). However, this amount can be modified as required.
√
Ⅲ The amount of coffee to be made is now programmed.
Ⅲ
Ⅲ
COFFEE READY
You can also make the cappuccino settings in the program-
ming mode (see Chapter 15.6)
Ⅲ Place a cup under the hot water spout (12).
Ⅲ Press the Hot Water key
message appears:
and hold it down until the following
14.3 Milk setting
The system’s basic settings include a pre-defined amount of milk
(20 sec.). However, this amount can be modified as required.
Ⅲ
Ⅲ
HOT WATER
PORTION
Ⅲ
Ⅲ
COFFEE READY
Ⅲ Machine dispenses hot water. Keep on holding the key
until the following message is displayed:
down
Ⅲ
Ⅲ
ENOUGH WATER
PRESS BUTTON
Ⅲ Place a cup under the cappuccino nozzle (4).
Ⅲ Press the Milk key
and hold it down until the following mes-
sage appears:
Ⅲ When the machine has dispensed as much hot water as you
wanted, briefly press the key
once more.
Ⅲ
Ⅲ
MILK
Ⅲ
Ⅲ
CONFIRMED
20 SEC (example)
√
Ⅲ The milk will be dispensed. Keep on holding the key
down
until the following message is displayed:
Ⅲ The amount of water to be dispensed is now programmed.
Ⅲ
Ⅲ
ENOUGH MILK
PRESS BUTTON
19
15. Programming
15.3 Maintenance
The IMPRESSA leaves the factory with a number of default
You can activate the following maintenance functions from this
program item:
settings that allow you to make coffee without having to pro-
gram the machine first. You can, however, adjust various
parameters to make the coffee suit your personal taste.
RINSING MACHINE, CLEAN CAPPUCCINO,
CHANGE FILTER, CLEAN UNIT, RINSE CAPPUCCINO,
DECALCIFY MACHINE.
The following parameters can be programmed:
“DECALCIFY MACHINE” is not displayed if you are using a
CLARIS plus filter and the filter is set to “Yes”.
ț Filter
ț Water hardness
ț Maintenance
ț Temperature
ț Coffee strength
ț Cappuccino
ț Milk
“CHANGE FILTER” is not displayed if you are not using a
CLARIS plus filter and the filter is set to “No”.
Ⅲ
Ⅲ
COFFEE READY
Ⅲ Press the Rotary Switch (B) until you hear an acoustic signal.
ț Save energy
ț Time
Ⅲ
Ⅲ
FILTER
ț Automatic switch-on time
ț Automatic switch-off time
ț Information
ț Rename
ț Language
ț Display
NO or YES
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
played:
Ⅲ
Ⅲ
MAINTENANCE
Ⅲ Press the Rotary Switch (B) to start programming.
15.1 Programming the filter
Ⅲ
Ⅲ
RINSE UNIT
Please refer to Chapter 5 “Using the CLARIS plus filter cartridge”.
Ⅲ Turn the Rotary Switch (B) until the required maintenance func-
tion (for selection see above) is displayed. Press the Rotary
Switch (B) to activate the function.
15.2 Programming your machine to the correct
water hardness (only with FILTER NO)
Please refer to Chapter 4 “Adjusting your machine to the water
hardness”.
15.4 Programming the temperature for coffee,
espresso, cappuccino and special coffee
You can adjust the temperature for each type of coffee sepa-
rately. The temperature can be set to 3 different levels
(LOW, NORMAL, HIGH).
20
Ⅲ
Ⅲ
COFFEE READY
Ⅲ
Ⅲ
COFFEE READY
Ⅲ Press the Rotary Switch (B) until you hear an acoustic signal.
15.5 Programming the coffee strength
Ⅲ
Ⅲ
FILTER
NO or YES
You can adjust the strength of each individual coffee product
separately. The coffee strength can be set to 5 different levels
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
E
(VERY MILD , MILD
STRONG
, NORMAL
).
,
played:
, XSTRONG
Ⅲ
Ⅲ
TEMPERATURE
Ⅲ
Ⅲ
COFFEE READY
Ⅲ Press the Rotary Switch (B) to start programming.
Ⅲ
Ⅲ
TEMPERATURE
COFFEE READY
Ⅲ Press the Rotary Switch (B) until you hear an acoustic signal.
Ⅲ
Ⅲ
FILTER
Ⅲ Then press a product key of your choice.
NO or YES
Ⅲ
Ⅲ
1 ESPRESSO (example)
NORMAL
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
played:
Ⅲ Turn the Rotary Switch until the required temperature is set.
Ⅲ
Ⅲ
AROMA
Ⅲ
Ⅲ
1 ESPRESSO (example)
HIGH (example)
Ⅲ Now press the Rotary Switch (B) to start programming.
Ⅲ Confirm the selected setting by pressing the Rotary Switch (B).
Ⅲ
Ⅲ
AROMA
Ⅲ
Ⅲ
Ⅲ
Ⅲ
CONFIRMED
COFFEE READY
√
Ⅲ Then press a product key of your choice.
TEMPERATURE
Ⅲ
Ⅲ
1 ESPRESSO (example)
NORMAL
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
played:
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
played:
Ⅲ
Ⅲ
EXIT
Ⅲ
Ⅲ
1 ESPRESSO (example)
STRONG (example)
Ⅲ Now press the Rotary Switch (B) to leave the programming
mode.
Ⅲ Confirm the selected setting by pressing the Rotary Switch (B).
CONFIRMED
Ⅲ
21
Ⅲ
Ⅲ
Ⅲ
√
Ⅲ
Ⅲ
CAPPUCCINO
AROMA
MILK 12 SEC (example)
Ⅲ Confirm the selected setting by pressing the Rotary Switch (B).
Ⅲ Now turn the Rotary Switch (B) until the following message is
displayed:
Ⅲ
Ⅲ
Ⅲ
Ⅲ
CONFIRMED
√
Ⅲ
Ⅲ
EXIT
CAPPUCCINO
COFFEE 100 ML (example)
Ⅲ Now press the Rotary Switch (B) to leave the programming
mode.
Ⅲ Now turn the Rotary Switch (B) until the required amount of
coffee is set.
Ⅲ
Ⅲ
COFFEE READY
Ⅲ
Ⅲ
CAPPUCCINO
COFFEE 110 ML (example)
Ⅲ Confirm the selected setting by pressing the Rotary Switch (B).
15.6 Cappuccino programming
Ⅲ
Ⅲ
Ⅲ
Ⅲ
CONFIRMED
√
You can also make the cappuccino settings in the program-
ming mode or as described in Chapter 14.2 “Cappuccino set-
ting”.
CAPPUCCINO
MILK 12 SEC (example)
Ⅲ Now turn the Rotary Switch (B) until the following message is
displayed:
Ⅲ
Ⅲ
COFFEE READY
Ⅲ
Ⅲ
EXIT
Ⅲ Press the Rotary Switch (B) until you hear an acoustic signal.
Ⅲ
Ⅲ
FILTER
Ⅲ Now press the Rotary Switch (B) to leave the programming
NO or YES
mode.
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
played:
Ⅲ
Ⅲ
COFFEE READY
Ⅲ
Ⅲ
CAPPUCCINO
MILK 15 SEC (example)
15.7 Programming the milk
Ⅲ Now press the Rotary Switch (B) to start programming.
You can also set the amount of milk in the programming
mode or as described in Chapter 14.3 “Milk setting”.
Ⅲ
Ⅲ
CAPPUCCINO
MILK 15 SEC (example)
Ⅲ Now turn the Rotary Switch (B) until the required amount of
milk is set.
Ⅲ
COFFEE READY
22
15.8 Save energy
Ⅲ
Ⅲ Press the Rotary Switch (B) until you hear an acoustic signal.
You can set your machine to various power saving modes.
Ⅲ
Ⅲ
FILTER
NO or YES
Ⅲ
Ⅲ
COFFEE READY
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
played:
E
Ⅲ Press the Rotary Switch (B) until you hear an acoustic signal.
Ⅲ
Ⅲ
MILK
Ⅲ
Ⅲ
FILTER
20 SEC (example)
NO or YES
Ⅲ Now press the Rotary Switch (B) to start programming.
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
played:
Ⅲ
Ⅲ
MILK
20 SEC (example)
Ⅲ
Ⅲ
ENERGY
SAVE NO
Ⅲ Now turn the Rotary Switch (B) until the required amount of
milk is set.
Ⅲ Now press the Rotary Switch (B) to start programming.
Ⅲ
Ⅲ
MILK
Ⅲ
Ⅲ
ENERGY
SAVE NO
28 SEC (example)
Ⅲ Confirm the selected setting by pressing the Rotary Switch (B).
Ⅲ Now turn the Rotary Switch (B) until the required power saving
mode is displayed.
Ⅲ
Ⅲ
Ⅲ
Ⅲ
CONFIRMED
√
Ⅲ
Ⅲ
ENERGY
MILK
SAVE LEVEL 2 (example)
28 SEC (example)
Ⅲ Confirm the selected setting by pressing the Rotary Switch (B).
Ⅲ Now turn the Rotary Switch (B) until the following message is
Ⅲ
Ⅲ
Ⅲ
Ⅲ
CONFIRMED
displayed:
√
Ⅲ
Ⅲ
EXIT
ENERGY
SAVE LEVEL 2 (example)
Ⅲ Now press the Rotary Switch (B) to leave the programming
Ⅲ Now turn the Rotary Switch (B) until the following message is
displayed:
mode.
Ⅲ
Ⅲ
COFFEE READY
Ⅲ
Ⅲ
EXIT
23
Ⅲ Now press the Rotary Switch (B) to leave the programming
mode.
15.9 Setting the time
You already set the time when you used the IMPRESSA for
the first time. This programming option allows you to
modify that setting.
Ⅲ
Ⅲ
COFFEE READY
Ⅲ
Ⅲ
COFFEE READY
Save energy: No
Selecting this level puts the IMPRESSA in constant stand-by
mode.
Ⅲ Press the Rotary Switch (B) until you hear an acoustic signal.
This setting allows you to make coffee or frothed milk without
having to wait for the machine to heat up.
Ⅲ
Ⅲ
FILTER
NO or YES
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
played:
This setting is useful if you make a lot of coffee and milk
products and want your machine to be in stand-by all the
time.
Ⅲ
Ⅲ
TIME
12:45 (example)
Save energy: Level 1
Ⅲ Now press the Rotary Switch (B) to start programming.
Selecting this level puts the IMPRESSA in constant stand-by mode
for making coffee. The machine is heated up separately to make
frothed milk.
Ⅲ
Ⅲ
TIME
HOURS 12:45
Ⅲ Turn the Rotary Switch (B) to set the hours.
Ⅲ
Ⅲ
TIME
This setting is useful if you mostly make black coffees and
are prepared to wait for 1 minute before being able to froth
milk.
HOURS 13:45 (example)
Ⅲ Press the Rotary Switch (B) to confirm the hours and to activate
the minutes.
Save energy: Level 2
Ⅲ
Ⅲ
TIME
Selecting this level does not put the IMPRESSA in stand-by mode
(economy temperature). The machine heats up separately each time
you make coffee or frothed milk.
The machine switches to economy temperature 5 minutes after you
last used it.
MINUTES 13:45
Ⅲ Turn the Rotary Switch (B) to set the minutes.
Ⅲ
Ⅲ
TIME
13:50 (example)
Ⅲ Confirm the minutes by pressing the Rotary Switch (B).
This setting is useful if you make very few coffees (with or
without milk) and are prepared to wait 30 seconds for the
machine to get ready.
Ⅲ
Ⅲ
CONFIRMED
√
24
Ⅲ
Ⅲ
TIME
13:50
Ⅲ
Ⅲ
UNIT ON
MINUTES 07:00
Ⅲ Now turn the Rotary Switch (B) until the following message is
Ⅲ Turn the Rotary Switch (B) to set the minutes.
displayed:
Ⅲ
Ⅲ
UNIT ON
Ⅲ
Ⅲ
EXIT
07:30 (example)
Ⅲ Confirm the minutes by pressing the Rotary Switch (B).
E
Ⅲ Now press the Rotary Switch (B) to leave the programming
Ⅲ
Ⅲ
Ⅲ
Ⅲ
CONFIRMED
√
mode.
Ⅲ
Ⅲ
COFFEE READY
UNIT ON
07:30
Ⅲ Now turn the Rotary Switch (B) until the following message is
displayed:
15.10 Programming the automatic switch-on time
Ⅲ
Ⅲ
COFFEE READY
Ⅲ
Ⅲ
EXIT
Ⅲ Press the Rotary Switch (B) until you hear an acoustic signal.
Ⅲ Now press the Rotary Switch (B) to leave the programming
mode.
Ⅲ
Ⅲ
FILTER
Ⅲ
Ⅲ
COFFEE READY
NO or YES
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
played:
To deactivate the automatic switch-on time, set the time to
—:—.
Ⅲ
Ⅲ
UNIT ON
—:—
Ⅲ Now press the Rotary Switch (B) to start programming.
15.11 Programming the automatic switch-off time
Ⅲ
Ⅲ
UNIT ON
Ⅲ
Ⅲ
COFFEE READY
HOURS 00:00
Ⅲ Turn the Rotary Switch (B) to set the hours.
Ⅲ Press the Rotary Switch (B) until you hear an acoustic signal.
Ⅲ
Ⅲ
UNIT ON
Ⅲ
Ⅲ
FILTER
HOURS 07:00 (example)
NO or YES
Ⅲ Press the Rotary Switch (B) to confirm the hours and to activate
the minutes.
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
played:
25
Ⅲ Press the Rotary Switch (B) until you hear an acoustic signal.
Ⅲ
Ⅲ
OFF AFTER
5 HRS
Ⅲ
Ⅲ
FILTER
NO or YES
Ⅲ Now press the Rotary Switch (B) to start programming.
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
played:
Ⅲ
Ⅲ
OFF AFTER
5 HRS
Ⅲ
Ⅲ
INFORMATION
Ⅲ Turn the Rotary Switch (B) to set the switch-off time.
Ⅲ
Ⅲ
OFF AFTER
Ⅲ Now press the Rotary Switch (B) to access the information
menu.
4 HRS (example)
Ⅲ Confirm the automatic switch-off time by pressing the Rotary
Ⅲ
Ⅲ
1 ESPRESSO
Switch (B).
1000 COUNT (example)
Ⅲ
Ⅲ
Ⅲ
Ⅲ
CONFIRMED
√
Ⅲ Turn the Rotary Switch (B) to display how often you made 2
espressos, 1 coffee, 2 coffees, cappuccino, special coffee, frothed
milk and hot water.
OFF AFTER
4 HRS
Ⅲ Then the water and milk quantities are displayed.
Ⅲ Now turn the Rotary Switch (B) until the following message is
displayed:
Ⅲ
Ⅲ
1 ESPRESSO (example)
AMOUNT 50 ML (example)
Ⅲ
Ⅲ
EXIT
Ⅲ Turn the Rotary Switch (B) to display any further water and milk
quantities.
Ⅲ Now press the Rotary Switch (B) to leave the programming
mode.
Ⅲ Finally, the number of decalcifying and cleaning cycles and filter
changes are displayed.
Ⅲ
Ⅲ
COFFEE READY
Ⅲ To exit the information program, press the Rotary Switch (B).
Ⅲ
Ⅲ
INFORMATION
15.12 Information
Ⅲ Now turn the Rotary Switch (B) until the following message is
displayed:
This program item enables you to check the number of cof-
fees or frothed milk you made, i.e. how often you selected a
certain function, and the values that are programmed.
Ⅲ
Ⅲ
EXIT
Ⅲ Now press the Rotary Switch (B) to leave the programming
mode.
Ⅲ
Ⅲ
COFFEE READY
26
Ⅲ
Ⅲ
COFFEE READY
Ⅲ
ABCDEFG...√
Ⅲ Enter a text of your choice by selecting letters (highlighted in
red) with the Rotary Switch (B) and confirming by pressing the
Rotary Switch (B).
15.13 Renaming
Ⅲ To confirm your text, select √ which you will find at the end of
This function allows you to rename the different products as
well as change the welcome and end text.
the alphabet (after the arrow).
E
Ⅲ
Ⅲ
MY COFFEE (example)
ABCDEFG.....
Ⅲ
Ⅲ
COFFEE READY
Ⅲ Confirm by pressing the Rotary Switch (B).
Ⅲ
Ⅲ
Ⅲ
Ⅲ
CONFIRMED
√
Ⅲ Press the Rotary Switch (B) until you hear an acoustic signal.
Ⅲ
Ⅲ
FILTER
RENAME
NO or YES
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
played:
Ⅲ Now turn the Rotary Switch (B) until the following message is
displayed:
Ⅲ
Ⅲ
RENAME
Ⅲ
Ⅲ
EXIT
Ⅲ Now press the Rotary Switch (B) to start programming.
Ⅲ Now press the Rotary Switch (B) to leave the programming
mode.
Ⅲ
Ⅲ
RENAME
PRODUCT NAME
Ⅲ
Ⅲ
COFFEE READY
Ⅲ Turn the Rotary Switch further to select WELCOME MESSAGE
or END MESSAGE.
Ⅲ Press the Rotary Switch (B).
To reset to the original product name, select the following
display and confirm.
Ⅲ
Ⅲ
PRODUCT NAME (example)
CHANGE
Ⅲ
Ⅲ
PRODUCT NAME
RESET
Ⅲ Press the Rotary Switch (B).
Ⅲ
Ⅲ
PRODUCT NAME
COFFEE READY
You can also reset all the product names to their original
names in one step. Select the following display and confirm.
Ⅲ Press a key of your choice (only required for PRODUCT
NAME).
Ⅲ
Ⅲ
PRODUCT NAME
RESET ALL
Ⅲ
_
27
15.14 Programming the language
15.15 Programming the display
Ⅲ
Ⅲ
COFFEE READY
This program item allows you to change the time format
from 24 hrs. to AM/PM and the units from ml (millilitres) to
oz (ounces).
Ⅲ Press the Rotary Switch (B) until you hear an acoustic signal.
Ⅲ
Ⅲ
FILTER
Changing the units
NO or YES
Ⅲ
Ⅲ
COFFEE READY
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
played:
Ⅲ Press the Rotary Switch (B) until you hear an acoustic signal.
Ⅲ
Ⅲ
LANGUAGE
ENGLISH
Ⅲ
Ⅲ
FILTER
NO or YES
Ⅲ Now press the Rotary Switch (B) to start programming.
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
played:
Ⅲ
Ⅲ
LANGUAGE
ENGLISH
Ⅲ
Ⅲ
SETTINGS
Ⅲ Turn the Rotary Switch (B) to set the language.
Ⅲ
Ⅲ
LANGUAGE
Ⅲ Now press the Rotary Switch (B) to start programming.
ENGLISH (example)
Ⅲ
Ⅲ
SETTINGS
UNIT
Ⅲ Confirm the selected language by pressing the Rotary Switch
(B).
Ⅲ Now press the Rotary Switch (B).
Ⅲ
Ⅲ
Ⅲ
Ⅲ
CONFIRMED
√
Ⅲ
Ⅲ
SETTINGS
UNIT ML
LANGUAGE
Ⅲ Turn the Rotary Switch (B) to change the units.
ENGLISH
Ⅲ
Ⅲ
SETTINGS
UNIT OZ
Ⅲ Now turn the Rotary Switch (B) until the following message is
displayed:
Ⅲ Confirm your selection by pressing the Rotary Switch (B).
Ⅲ
Ⅲ
EXIT
Ⅲ
Ⅲ
Ⅲ
Ⅲ
CONFIRMED
√
Ⅲ Now press the Rotary Switch (B) to leave the programming
mode.
SETTINGS
Ⅲ
Ⅲ
COFFEE READY
28
Ⅲ Now turn the Rotary Switch (B) until the following message is
displayed:
Ⅲ
Ⅲ
SETTINGS
FORMAT AM/PM
Ⅲ
Ⅲ
EXIT
Ⅲ Confirm your selection by pressing the Rotary Switch (B).
Ⅲ
Ⅲ
Ⅲ
Ⅲ
CONFIRMED
√
Ⅲ Now press the Rotary Switch (B) to leave the programming
mode.
SETTINGS
E
Ⅲ
Ⅲ
COFFEE READY
Ⅲ Now turn the Rotary Switch (B) until the following message is
displayed:
Changing the time format
Ⅲ
Ⅲ
EXIT
Ⅲ
Ⅲ
COFFEE READY
Ⅲ Now press the Rotary Switch (B) to leave the programming
mode.
Ⅲ Press the Rotary Switch (B) until you hear an acoustic signal.
Ⅲ
Ⅲ
COFFEE READY
Ⅲ
Ⅲ
FILTER
NO or YES
Ⅲ Turn the Rotary Switch (B) until the following message is dis-
played:
16. Maintenance
Ⅲ
Ⅲ
SETTINGS
16.1 Filling the water tank
Ⅲ
Ⅲ
WATER TANK
FILL
Ⅲ Now press the Rotary Switch (B) to start programming.
Ⅲ
Ⅲ
SETTINGS
UNIT
If this information is displayed, the machine will no longer
produce coffee, hot water or milk. Refill water as described
in Chapter 2.3.
Ⅲ Turn the Rotary Switch (B).
Ⅲ
Ⅲ
SETTINGS
TIME FORMAT
Ⅲ
Ⅲ
COFFEE READY
Ⅲ Press the Rotary Switch (B).
Ⅲ
Ⅲ
SETTINGS
The water tank should be rinsed out and filled with fresh
water daily. Always use fresh, cold water. Never fill the
water tank with milk, mineral water or other liquids.
FORMAT 24 HRS
Ⅲ Turn the Rotary Switch (B) to change the format.
29
On the IMPRESSA Z5 Chrome we recommend that the cup
platform (2b) is removed first followed by the drip tray and
the coffee grounds tray with bin.
16.2 Emptying the coffee grounds
Ⅲ
Ⅲ
GROUNDS
EMPTY
Ⅲ Carefully take out the drip tray (1) – which contains water – and
the coffee grounds tray with the container (3).
If this information is displayed, the machine will no longer
make coffee. The machine will still make hot water and
frothed milk, however. Empty the coffee grounds container
(3).
Ⅲ
Ⅲ
TRAY
MISSING
Ⅲ Place the empty, clean drip tray (1) and the coffee grounds tray
with the container (3) back into the IMPRESSA.
On the IMPRESSA Z5 Chrome we recommend that the cup
platform (2b) is removed first followed by the drip tray and
the coffee grounds tray with bin.
Ⅲ
Ⅲ
COFFEE READY
Ⅲ Carefully take out the drip tray (1) – which contains water – and
the coffee grounds tray with the container (3).
16.4 Drip tray missing
Ⅲ
Ⅲ
TRAY
Ⅲ
Ⅲ
TRAY
MISSING
MISSING
Ⅲ Place the empty, clean drip tray (1) and the coffee grounds tray
with the container (3) back into the IMPRESSA. (The coffee
grounds tray must be outside the machine for at least 10 sec-
onds).
If this information is displayed, the machine will no longer
make coffee, hot water or frothed milk. The drip tray (1) has
not been installed or not been installed properly.
Ⅲ
Ⅲ
COFFEE READY
Ⅲ Insert the drip tray (1).
Ⅲ
Ⅲ
COFFEE READY
16.3 Emptying the drip tray
Ⅲ
Ⅲ
TRAY
16.5 Grounds container missing
EMPTY
Ⅲ
Ⅲ
COFFEE BIN
MISSING
If this information is displayed, the machine will no longer
make coffee, hot water or frothed milk, and the coffee
grounds container must be emptied.
If this information is displayed, the machine will no longer
make coffee, hot water or frothed milk. The drip tray (3) has
not been installed or not been installed properly.
30
Ⅲ Insert the drip tray (3).
Ⅲ Open the cover of the bean tank (7) and remove the aroma
preservation cover (8).
Ⅲ
Ⅲ
COFFEE READY
Ⅲ Remove any beans with a vacuum cleaner.
Ⅲ Insert the key (Fig. 12).
Ⅲ Now turn the key conter-clockwise until the jammed stone is
released.
16.6 Filling the bean tank
Ⅲ
Ⅲ
COFFEE READY
FILL BEANS
E
Ⅲ Remove any remaining powder with a vacuum cleaner.
Ⅲ Fill up with fresh beans.
If this information is displayed, the machine will no longer
make coffee. The machine will still make hot water and
frothed milk, however. Refill beans as described in Chapter
2.4.
16.9 Changing the filter
After having used 50 litres of water or after two months, the
filter cartridge will be used up. The display will prompt you
to change the filter.
Ⅲ
Ⅲ
COFFEE READY
Refer to Chapter 5.2 “Changing the filter”.
16.7 Aroma preservation cover missing
16.10 Information about cleaning cycle
Ⅲ
Ⅲ
BEANCOVER
MISSING
After having dispensed 220 products or after 160 rinsing cycles,
the IMPRESSA must be cleaned. You will be informed of this by a
message on the display. The machine will still make coffee, hot
water and frothed milk. However, we recommend that you should
run the cleaning cycle (Chapter 17) within the next few days.
If this information is displayed, the machine will no longer
make coffee. The machine will still make hot water and
frothed milk, however. The aroma preservation cover (8) has
not been installed or not been installed properly.
Ⅲ
Ⅲ
COFFEE READY
CLEAN
Ⅲ Install the aroma preservation cover (8).
After the machine has dispensed another 30 products, the display
begins to flash. You should run the cleaning cycle now (Chapter
17).
Ⅲ
Ⅲ
COFFEE READY
Ⅲ
Ⅲ
COFFEE READY
CLEAN (flashing)
16.8 Removing stones from the grinding gear
Ⅲ Switch the machine off using the ON / OFF key
(A).
Ⅲ Turn the power switch (15) off.
31
After another 10 products, the display will change. Please run the
cleaning cycle immediately (see Chapter 17).
Ⅲ Place a receptacle each under the height-adjustable hot water
spout (12) and under the cappuccino nozzle (4).
Ⅲ
Ⅲ
CLEAN NOW
Ⅲ Take out the water tank (Fig. 1).
CLEAN (flashing)
Ⅲ Press the maintenance key
(C) until the following message
appears:
Ⅲ
Ⅲ
SYS EMPTY
16.11 Information about decalcify
Lime scale builds up in the IMPRESSA as a result of normal use.
The degree of calcification depends on the hardness of the water
you use. The IMPRESSA Z5 recognizes when you should run a de-
calcifying cycle. The machine will still make coffee, hot water and
frothed milk. However, we recommend that you should decalcify
the machine (Chapter 18) within the next few days.
Ⅲ When the process has been completed, the IMPRESSA Z5
switches itself off.
Next time you switch on the machine, the display will read PRESS
MAINT., meaning that the system needs to be filled with water.
Please refer to Chapter 3 “First use”.
Ⅲ
Ⅲ
COFFEE READY
DESCALE
17. Cleaning
After a while the display will begin to flash. You should run the
decalcifying cycle now Chapter 18).
The IMPRESSA features an integrated cleaning program. The
process takes approx.15 minutes.
Ⅲ
Ⅲ
COFFEE READY
Please contact your authorized dealer for JURA cleaning
tablets that are suitable specifically for the cleaning program
of your IMPRESSA. Please note that the use of unsuitable
cleaning agents may cause damage to your machine and
could leave unfavourable residues in the water.
DESCALE (flashing)
After a while the display will change if you have still not decalci-
fied the machine. Please run the decalcifying cycle immediately
(see Chapter 18).
Ⅲ
Ⅲ
DECALCIFY NOW
DESCALE (flashing)
Once started, the cleaning process must not be interrupted.
When the cleaning program has finished, take out the re-
movable coffee powder tank (9) and briefly rinse it under
running water.
16.12 Emptying the system
Requirements: The IMPRESSA has been switched off with the
ON / OFF key
(A), but the power switch is still turned on.
Ⅲ
Ⅲ
COFFEE READY
CLEAN
This is necessary to protect the machine against damage
occurring during transport as a result of frost.
Ⅲ Press the maintenance key
(C).
32
Ⅲ Empty the drip tray (1) and the coffee grounds tray with the
container (3).
Ⅲ
Ⅲ
TRAY / GROUNDS
EMPTY
Ⅲ
Ⅲ
TRAY
Ⅲ Empty the drip tray (1) and the coffee grounds tray with the con-
MISSING
tainer (3).
Ⅲ Place the empty, clean drip tray (1) and the coffee grounds tray
with the container (3) back into the IMPRESSA.
Ⅲ
Ⅲ
TRAY
MISSING
E
Ⅲ
Ⅲ
COFFEE READY
Ⅲ Place the empty, clean drip tray (1) and the coffee grounds tray
with the container (3) back into the IMPRESSA.
Ⅲ
You can also trigger a cleaning cycle manually from the
maintenance menu at any point in time (see Chapter 15.3).
Ⅲ
PRESS BUTTON
Ⅲ Place a sufficiently large receptacle (ca. 0.5 litres) each under the
height-adjustable coffee spout (11) and under the cappuccino
nozzle (4).
18. Decalcifying
The IMPRESSA features an integrated decalcifying program. The
process takes approx.50 minutes.
Ⅲ Press the maintenance key
(C).
Ⅲ
Ⅲ
MACHINE IS CLEANING
Lime scale builds up in the IMPRESSA as a result of normal
use. The degree of calcification depends on the hardness of
the water you use. The IMPRESSA recognizes when you
should run a decalcifying cycle. The machine will still make
coffee, frothed milk and hot water. However, we recom-
mend that you should decalcify the machine within a few
days after the message was displayed.
Ⅲ You will hear an acoustic signal.
Ⅲ
Ⅲ
ADD TABLET
Ⅲ Open the lid of the filler funnel for pre-ground coffee (9). It is
under the bean tank cover (7).
Ⅲ Drop a cleaning tablet inside (Fig. 5) and close the lid.
Please contact your authorized dealer for JURA decalcifying
tablets that are suitable specifically for the decalcifying pro-
gram of your IMPRESSA. Please note that the use of unsuit-
able decalcifying agents may cause damage to your machine
and could leave unfavourable residues in the water.
Ⅲ
Ⅲ
PRESS BUTTON
Ⅲ Press the maintenance key
(C).
MACHINE IS CLEANING
Ⅲ
Ⅲ
Remove any splashes or drops of the decalcifying agent from
sensitive surfaces, in particular surfaces made of natural
stone or wood, or take appropriate preventive measures.
Ⅲ You will hear an acoustic signal.
Ⅲ
Ⅲ
TRAY / GROUNDS
EMPTY
33
Once started, the decalcifying program must not be inter-
rupted.
Ⅲ
Ⅲ
MACHINE IS DECALCIFYING
Ⅲ You will hear an acoustic signal.
Always wait until the decalcifying agent has been used up
and the tank is empty. Never fill in additional descaling
agent.
Ⅲ
Ⅲ
TRAY / GROUNDS
EMPTY
Ⅲ Empty the drip tray (1) and the coffee grounds tray with the con-
tainer (3).
Ⅲ
Ⅲ
COFFEE READY
DESCALE
Ⅲ
Ⅲ
TRAY
Ⅲ Press the maintenance key
(C).
TRAY / GROUNDS
EMPTY
MISSING
Ⅲ
Ⅲ
Ⅲ Place the empty, clean drip tray (1) and the coffee grounds tray
with the container (3) back into the IMPRESSA.
Ⅲ Empty the drip tray (1) and the coffee grounds tray with the
container (3).
Ⅲ
Ⅲ
WATER TANK
FILL
Ⅲ
Ⅲ
TRAY
MISSING
Thouroughly rinse out the water tank and fill it with fresh
cold tap water. Then place it back into the IMPRESSA.
Ⅲ Place the empty, clean drip tray (1) and the coffee grounds tray
with the container (3) back into the IMPRESSA Z5.
Ⅲ
Ⅲ
Ⅲ
Ⅲ
SOLVENT IN TANK
PRESS BUTTON
PRESS BUTTON
Ⅲ Re-assemble the cappuccino nozzle.
Ⅲ Remove the water tank from the machine. Empty out any
Ⅲ Place a cup each under the height-adjustable hot water spout (12)
and the cappuccino nozzle (4), and press the maintenance key
(C).
remaining water.
Completely dissolve the content of one blister (3 tablets) in a
receptacle containing 0.6 litres of water, and pour the mixture into
the water tank. Place the water tank back into the machine.
Ⅲ
Ⅲ
Ⅲ
Ⅲ
MACHINE IS DECALCIFYING
UNIT IS HEATING
Ⅲ
Ⅲ
SOLVENT IN TANK
PRESS BUTTON
Ⅲ After the machine has heated up, it will automatically perform a
rinsing cycle.
Ⅲ Remove the cappuccino nozzle (4) from the machine (Fig. 14).
Ⅲ Place a receptacle each under the height-adjustable hot water
spout (12) and under the connecting parts of the nozzle (use tall
receptacle). Press the maintenance key
Ⅲ
Ⅲ
RINSING
(C).
34
Ⅲ You will hear an acoustic signal.
20. Tips for perfect coffee
Ⅲ
Ⅲ
TRAY / GROUNDS
EMPTY
Height-adjustable coffee spout (11)
You can adjust the height of the coffee spout to the size of your
cups.
Ⅲ Empty the drip tray (1) and the coffee grounds tray with the
container (3).
Grinding degree
Refer to Chapter 2.5 “Adjusting the grinding gear”.
Ⅲ
Ⅲ
TRAY
E
MISSING
Preheating cups
Ⅲ Place the empty, clean drip tray (1) and the coffee grounds tray
You can preheat the cups with hot water. The smaller the quantity
of coffee you make, the more important preheating is.
with the container (3) back into the IMPRESSA.
Ⅲ
Ⅲ
COFFEE READY
Sugar and cream
Stirring coffee/tea will result in heat being released. Adding refrig-
erated cream or milk will reduce the temperature of the coffee sig-
nificantly.
You can also trigger a decalcifying cycle manually from the
maintenance menu at any point in time (see Chapter 15.3).
19. Disposal
Please return the IMPRESSA to your local dealer, the service shop
or to JURA for proper disposal.
35
21. Problems
Problem
Cause
Remedy
Very loud noise coming from the grinding
gear
Foreign body in grinding gear
Please refer to Chapter 16.8
Frothing spout squirts
Milk hose not properly attached
Make sure the milk hose is properly
attached
Too little froth when frothing milk
Cappuccino nozzle clogged
Grinding degree too fine
Pre-ground coffee too fine
Clean nozzle (Chapter 9.4)
Coffee only drips from the coffee spout
Adjust grinding gear to coarser grind
Use a coarser type of pre-ground
coffee
Message: Display constantly indicates
‘Empty tray’
Soiled metal contacts at rear of drip tray
Bean monitoring system soiled
Clean metal contacts
Clean bean tank (dry)
‘Fill beans’ not displayed despite empty
bean tank
36
22. Legal information
23. Technical data
Voltage:
These operating instructions contain all the information required
for using, operating and maintaining the machine properly.
230V AC
1350 W
10 A
Power:
Knowledge of and compliance with the specifications contained in
these operating instructions is required for using the machine safely
as well as for operational safety and safety during maintenance.
These operating instructions cannot cover any conceivable appli-
cation. The machine was designed for private household use.
Additionally we point out that the content of these operating
instructions does not form part of any previous or existing agree-
ment, consent or al legal relationship nor does it constitute a
change of such an agreement, consent or legal relationship. Any
obligations to be fulfilled by JURA Elektroapparate AG are stipu-
lated in the corresponding purchase contract, which also contains
the full and solely applicable warranty stipulations. These con-
tractual warranty stipulations are neither extended nor limited by
the specifications contained in these operating instructions.
Fuse:
Safety check:
E
Energy consumption level no:
Energy consumption level 1:
Energy consumption level 2:
Pump pressure:
23 Wh
16 Wh
14 Wh
static, max. 15 bar
2.8 liter
Water tank:
Bean tank capacity:
Coffee grounds container capacity:
Milk container capacity:
Length of cable:
280 gr.
max. 20 portions
1 liter
The operating instructions contain information, protected by Copy-
right. Photocopying or translations into other languages shall not be
permissible without JURA Elektroapparate AG’s written approval.
approx. 1.1 m
Weight:
13.3 kg/13.8 kg
(IMPRESSA Z5 Chrome)
Size (WxHxD):
31 x 37 x 43.5 cm
The machine complies with the following EU directives:
73/23/EWG dated 19/02/1973 "Low Voltage Directive" including
Modification Directive 93/336/EWG
89/336/EWG dated 03/05/1989 "EMC Directive" including
Modification Directive 92/31/EWG
37
|