IMPRESSA X9
Instructions for use
Fig. 1
Fig. 5
Fig. 9
Fig. 13
Fig. 16
Fig. 2
Fig. 3
Fig. 7
Fig. 11
Fig. 4
A
B
Fig. 6
Fig. 8
A
B
Fig. 10
Fig. 14
Fig. 17
Fig. 12
̈
̇
̈
̇
Fig. 15
Fig. 18
N
O
P
Q
M
R
S
L
K
J
I
H
T
U
G
F
V
E
D
W
X
C
B
A
Operating elements Impressa X9
A
B
C
D
E
F
Drip tray
Drip grate
Grounds bin
Height-adjustable dual spout
Frothing key
Macchiato key
Milk Coffee key
2x key
G
H
I
Ristretto key
Espresso key
Coffee key
J
K
L
Cappuccino key
M Display dialog system (incl. graphics display)
N
O
P
Bean tank
Filler funnel for cleaning tablet
Cup railing
Q
R
S
Cover for programming keys
Water tank
Steam key
T
U
V
Hot Water key
Pivoting hot water spout
Pivoting steam spout
W Accessories drawer
Water tank cover
X
Programming keys
A
B
C
D
E
F
ON / OFF
Filter
Decalcify
Counter
Access programming mode
+
(Page through parameters/higher
values)
G
H
I
Rinse
Clean milk system
Clean coffee system
Clean dual spout
EXIT
J
K
L
–
(Page through parameters/lower
values)
5
Contents
JURA Impressa X9
1. Description of the machine......................................................................................................................page
1.1 Standard functions.........................................................................................................................page
1.2 DISPLAY to be made by a JURA service technician.............................................................................page
2. Safety information.................................................................................................................................page
2.1 Warnings .....................................................................................................................................page
2.2 Safety precautions .........................................................................................................................page
3. Preparing the machine ...........................................................................................................................page
3.1 Checking the mains voltage .............................................................................................................page
3.2 Checking the fuse ..........................................................................................................................page
3.3 Filling the water tank.....................................................................................................................page
3.4 Adding coffee beans .......................................................................................................................page
4. First use..............................................................................................................................................page
5. Switching the machine on .......................................................................................................................page
6. Rinsing the machine ..............................................................................................................................page
7. Setting the grinding degree .....................................................................................................................page
8. Adjusting your machine to the water hardness.............................................................................................page
9. Using the CLARIS plus filter cartridge......................................................................................................page
9.1 Installing the filter ........................................................................................................................page
10. Coffee .................................................................................................................................................page
10.1 Making coffee/espresso/ristretto........................................................................................................page
10.2 Making cappuccino/macchiato ..........................................................................................................page
10.3 Making milk coffee ........................................................................................................................page
10.4 Frothing milk................................................................................................................................page
10.5 2x key.........................................................................................................................................page
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
9
9
9
9
9
9
9
9
11. Making hot water..................................................................................................................................page 10
12. Drawing off steam .................................................................................................................................page 10
13. Switching the machine off.......................................................................................................................page 10
14. Programming .......................................................................................................................................page 10
14.1 Adjusting the machine to the water hardness.......................................................................................page 10
14.2 Customizing (product definition) .......................................................................................................page 10
14.3 Setting the time ............................................................................................................................page 11
14.4 Automatic switch-on time................................................................................................................page 11
14.5 Automatic switch-off time ...............................................................................................................page 11
14.6 Programming the language..............................................................................................................page 12
14.7 Setting up the display.....................................................................................................................page 12
14.7.1 Unit of measurement (ml/oz)..................................................................................................page 12
14.7.2 Time format........................................................................................................................page 12
14.8 Information ..................................................................................................................................page 12
15. Counter ...............................................................................................................................................page 13
16. Maintenance ........................................................................................................................................page 13
16.1 Filling the water tank...................................................................................................................page 13
16.2 Installing a fixed water supply system..............................................................................................page 13
16.3 Emptying the coffee grounds container.............................................................................................page 13
16.4 Emptying the drip tray .................................................................................................................page 13
16.5 Grounds bin missing .....................................................................................................................page 13
16.6 Filling the bean tank ....................................................................................................................page 13
16.7 Removing stones..........................................................................................................................page 13
16.8 General cleaning instructions .........................................................................................................page 14
16.9 Disassembling and cleaning the dual spout........................................................................................page 14
16.10 Cleaning the milk system...............................................................................................................page 14
16.11 Cleaning the coffee system.............................................................................................................page 14
16.12 Cleaning the dual spout.................................................................................................................page 15
16.13 Changing the filter.......................................................................................................................page 15
16.14 Decalcifying................................................................................................................................page 15
16.15 Cleaning the grinder and the bean tank............................................................................................page 16
17. Tips for perfect coffee ............................................................................................................................page 16
18. Messages.............................................................................................................................................page 17
19. Disposal ..............................................................................................................................................page 18
20. Legal information..................................................................................................................................page 18
21. Technical data ......................................................................................................................................page 18
6
Important Information for the user
2. Safety information
2.1 Warnings
Thank you for choosing this JURA product.
Please study these operating instructions carefully before using
your new machine and keep them in a safe place for easy reference
in the future.
Ⅲ Children are unaware of the dangers that can be caused by elec-
trical machines; for this reason, children should never be left
unsupervised with electrical machines.
Should you require further information or should particular prob-
lems occur that are not dealt with in sufficient detail for you in
these operating instructions, please ask your local dealer for the
information you require or get in touch with us directly.
Ⅲ The machine may only be used by people who have been
instructed.
Ⅲ Never use a faulty machine or one with a damaged power cable.
2.2 Safety precautions
Ⅲ Never expose the machine to the effects of weather (rain, snow,
frost) and never operate it with your hands wet.
Ⅲ Place your machine on a solid and level surface. Never leave it
on a warm or hot surface (hobs). Choose a location that is inac-
cessible for children or pets.
E
1. Description of the machine
Ⅲ If you intend not to use the machine for a longer time (e.g. holi-
days) always switch the machine off with the power switch
(Fig. 15/D) and disconnect the mains cable.
Spoil your customers, guests, staff and yourself with superb coffee
delights. Operating the IMPRESSA X9 is easy even for inexperi-
enced users. The display dialog system features plain text and com-
prehensible symbols that take you through each program step by
step. The Intelligent Pre Brew Aroma System (I.P.B.A.S.©) brings
out the full coffee aroma in espresso or coffee - always crowned by
a beautiful crema. You can have your coffee made with powder
from either of the two grinders or program a mixture according to
your personal preference. Cappuccino, latte macchiato or milk
coffee at the press of a key and without shifting around cups.
Ⅲ Always switch off the machine with the power switch (Fig.
15/D) and disconnect the mains cable before cleaning the ma-
chine.
Ⅲ When removing the plug from the power socket, never tug on the
corde of the machine itself.
Ⅲ Never repair or open the machine yourself. Repairs may only be
done by authorised service centres using original spare parts and
accessories.
The intelligent electronic system provides the utmost operating
convenience. For instance, the active bean tank monitor prompts
you to refill the two 650 g bean containers.
Ⅲ The machine is connected to the mains power socket via an
electric cable. Please ensure that no-one trips ober the cable and
pulls the machine down. Keep children and pets at a distance.
With the integrated rinsing, cleaning and decalcifying programs,
machine maintenance is done at the press of a key.
Ⅲ Never put the machine or parts of it into the dishwasher.
Ⅲ To precent overheating, please put the machine in a place with a
good circulation of air.
Ⅲ If you use de-scaling agents containing acid, remove any
splashes and drips on sensitive surfaces, in particular natural
stone and wood surfaces, straight away or take corresponding
safety precautions.
1.1 Standard functions
Your IMPRESSA X9 makes the following standard products
(Fig. 1):
Ⅲ Use service connectors A + B for approved manufacturer’s
accessories only (Fig. 15 A+ B).
A
B
C
D
COFFEE
ESPRESSO
RISTRETTO
2x
E
F
G
H
CAPPUCCINO
MILK COFFEE
MACCHIATO
FROTHED MILK
3. Preparing the machine
3.1 Checking the mains voltage
1.2 DISPLAY to be made by a JURA service
technician
The coffee machine is preset to the correct mains voltage. Check if
your local mains supply voltage complies with the information
given on the type plate on the rear of the coffee machine (Fig.
15/C).
The following DISPLAYcan only be made by a JURA service
technician:
a) Customer-specific product set-up. The standard products can be
replaced with:
– 2 espressos, 2 coffees, 2 ristrettos, pot of coffee, latte mac-
chiato, milk, hot water or steam at all times.
3.2 Checking the fuse
Check whether the fuse matches your machine (Fig. 15/C).
– Optionally you can preset the grinder or Rinse key.
The products can be arranged according to your personal
preference (Fig. 1).
3.3 Filling the water tank
Ⅲ Remove the water tank (Fig. 2) and rinse it out well with cold tap
water.
b) Lock products
c) All the products can be modified by a service technician to meet
the customer’s specific requirements.
Ⅲ Then fill the water tank and put it back into the machine.
Ⅲ Please ensure that the tank locks in properly.
d) Adjust filter capacity
e) Assign code groups
Please only use fresh, cold water. Never fill up with milk,
mineral water and other fluids. You can also top up water
without removing the tank. Simply remove the cover and
pour in the water from above with a vessel and replace the
lid again.
– A total of 3 code groups can be assigned. Each code group has
its own authorization.
7
3.4 Adding coffee beans
WELCOME TO
You have the possilility of using two different types of coffee
beans.
MACHINE HEAT
Ⅲ Remove the cover from the bean container (Fig. 3)
Ⅲ Clean out any dirt or foreign objects from the bean container.
Ⅲ Place a cup under the height-adjustable dual spout (Fig. 6).
Ⅲ Fill coffee beans into the bean container and replace the cover
again.
PRESS RINSE
Ⅲ Press the Rinse key (Fig. 5/G).
4. First use
RINSING
Make sure to have filled the water tank and the bean tank.
When rinsing the machine, start with the coffee spout and
then move on to the two milk spouts.
Ⅲ Switch the IMPRESSA X9 on with the power switch on the rear
of the machine (Fig. 15/D).
Ⅲ Open the programming door on the front (Fig. 4) and switch the
IMPRESSA X9 on with the ON / OFF key (Fig. 5/A).
6. Rinsing the machine
COFFEE READY
LANGUAGE
ENGLISH
Ⅲ Select a language of your choice by pressing the «+» or «–» key
Ⅲ Press the Rinse key (Fig. 5/G).
(Fig. 5/F or L).
RINSING
Ⅲ Press P to save your selection (Fig. 5/E).
CONFIRMED
When rinsing the machine, start with the coffee spout and
then move on to the two milk spouts.
TIME
HOURS
—:—
7. Setting the grinding degree
You can adjust the grinding gear to the roast of your coffee. We
recommend
Ⅲ Set the hours by pressing the «+» or «–» key (Fig. 5/F or L).
Ⅲ Press P to save your setting (Fig. 5/E).
a finer setting Ǟ (for a lighter roast)
TIME
a coarser setting Ǟ (for a darker roast)
MINUTES
12:00
Ⅲ To adjust the grinding degree, turn the setting rings to the
required position (Fig. 7).
Ⅲ Set the minutes by pressing the «+» or «–» key (Fig. 5/F or L).
Ⅲ You have the following options:
Ⅲ Press P to save your setting (Fig. 5/E).
The smaller the dots, the finer the grind
The larger the dots, the coarser the grind
CONFIRMED
The grinding degree may only be adjusted while the grinding
gear is running.
WELCOME TO
PRESS RINSE
8. Adjusting your machine to the water hardness
Water is heated in the machine. This leads to scale as a result of
use, which is automatically shown on the display. The machine
must be adjusted to match the hardness of the water used. For this,
please use the enclosed test stick.
Ⅲ Press the Rinse key (Fig. 5/G).
SYSTEM FILLI
1° German hardness is equivalent to 1.79° French hardness.
MACHINE HEAT
Ⅲ Place a cup under the height-adjustable dual spout (Fig. 6).
The machine can be adjusted from 1° German hardness up to 30°
German hardness. The function can also be deactivated.
PRESS RINSE
The IMPRESSA X9 is preset to 16° German hardness. You can
adjust your machine to the local water hardness. Example:
Ⅲ Press the Rinse key (Fig. 5/G).
RINSING
COFFEE READY
When rinsing the machine, start with the coffee spout and
then move on to the two milk spouts.
Ⅲ Press P (Fig. 5/E) until you hear an acoustic signal.
HARDNESS
5. Switching the machine on
Ⅲ Press P again (Fig. 5/E) to activate the programming step.
Ⅲ Switch the IMPRESSA X9 on with the power switch on the rear
of the machine (Fig. 15/D).
Ⅲ Adjust the machine to the required water hardness by pressing
the «+» or «–» key.
Ⅲ Open the programming door on the front (Fig. 4) and switch the
IMPRESSA X9 on with the ON / OFF key (Fig. 5/A).
8
HARDNESS
MACCHIATO
Ⅲ Press P to save your setting (Fig. 5/E).
Ⅲ Last of all the machine brews the coffee.
CONFIRMED
The upper of the two bargraphs indicates the duration of the
coffee brewing process.
Press any of the product keys to stop the frothing or the
brewing process prematurely.
HARDNESS
The milk system is rinsed automatically 10 minutes after dis-
pensing milk. You will hear an acoustic signal before the
rinsing cycle starts.
Ⅲ Press EXIT (Fig. 5/K).
SELECT PRODU
10.3 Making milk coffee
E
9. Using a CLARIS plus filter cartridge
COFFEE READY
When using the CLARIS plus filter cartridge properly, decal-
cifying your machine will no longer be necessary. For more
information on the CLARIS plus filter cartridge refer to the
CLARIS plus brochure “CLARIS. Hard on limescale. Gentle
on your coffee machine.”
Ⅲ Place a cup under the height-adjustable dual spout (Fig. 6) and
press the Milk Coffee key (Fig. 1/F).
MILK COFFEE
9.1 Installing the filter
Ⅲ Coffee and milk are discharged into the cup simultaneously.
Initial installation of a CLARIS plus filter cartridge needs
to be carried out by a service technician. Please contact your
service partner.
The upper of the two bargraphs indicates the duration of the
coffee brewing process.
Press any of the product keys to stop the frothing and the
brewing process prematurely.
Ⅲ Change the filter as described in Chapter 21.
The milk system is rinsed automatically 10 minutes after dis-
pensing milk. You will hear an acoustic signal before the
rinsing cycle starts.
10. Coffee
10.1 Making coffee/espresso/ristretto
COFFEE READY
10.4 Frothing milk
Ⅲ Place a cup under the height-adjustable dual spout (Fig. 6) and
press a product key of your choice. The pre-brewing process
(I.P.B.A.S.©) moistens the coffee powder, briefly interrupts the
flow of hot water and then begins with the actual brewing
process. The following example shows how to make 1 espresso.
COFFEE READY
Ⅲ Place a cup under the height-adjustable dual spout (Fig. 6) and
press the Frothing key (Fig. 1/H). Make sure the milk hoses
(Fig. 8/A) have been dipped into the milk.
1 ESPRESSO
MILK FROTH
A bargraph indicates the duration of the espresso brewing
process.
Ⅲ Your milk/frothed milk will be prepared.
A bargraph indicates the duration of the frothing process.
To stop the brewing process prematurely, press any of the
coffee keys. For a perfect frothing result, adjust the dual
spout (Fig. 6) to the size of your cup.
Press the frothing hos to stop the frothing process prema-
turely.
10.2 Making cappuccino/macchiato
10.5 2x key
COFFEE READY
You can make 2 coffees in one brewing step by preselecting
the 2x key. Press the 2x key and then the coffee key of your
choice.
Ⅲ Place a cup under the height-adjustable dual spout (Fig. 6) and
press the Macchiato key (Fig. 1/G). Make sure the milk hoses
(Fig. 8/A) have been dipped into the milk. The following exam-
ple shows how to make 1 macchiato.
The milk products cannot be doubled.
MACCHIATO
COFFEE READY
Ⅲ The IMPRESSA X9 starts by making the frothed milk.
Ⅲ Make 2 ristretti, espressi or coffees by pressing the 2x key
(Fig. 1/D) first.
The lower of the two bargraphs indicates the duration of the
milk frothing process.
COFFEE READY
9
Ⅲ Select a coffee product. For example, ristretto (Fig. 1/C)
14. Programming
2 RISTRETTI
The following parameters can be programmed:
¼ Water hardness
¼ Setup (product)
Ⅲ The machine will now make two ristrettos in one brewing step.
¼ Time
¼ Switch-on time
¼ Switch-off time
¼ Language
11. Making hot water
¼ Display (unit and time format)
COFFEE READY
¼ Information (number of products made, number of cleaning
cycles run)
Ⅲ Place a cup under the pivoting hot water spout (T) and press the
Hot Water key (T/ ).
14.1 Adjusting the machine to the water hardness
HOT WATER
For this, please refer to Chapter 8 “Adjusting your machine
to the water hardness”.
Ⅲ The machine stops dispensing the programmed portion of hot
water automatically.
14.2 Customizing (product definition)
A bargraph indicates the duration of the hot water dispensing
process.
You can program each product according to your preference.
Example: cappuccino
To stop the machine from dispensing hot water prematurely,
press any of the product keys.
COFFEE READY
Ⅲ Press P (Fig. 5/E) until you hear an acoustic signal.
There might be some initial splashing when drawing off hot
water. The pivoting hot water spout becomes hot. Avoid
direct contact with the skin!
HARDNESS
Ⅲ Press the «+» or «–» key until SETTING appears on the display.
12. Drawing off steam
SETTING
COFFEE READY
Ⅲ Press P again (Fig. 5/E) to activate the SETTING programming
step.
Ⅲ Place a cup under the pivoting steam spout (V) and press the
Steam key (S / ).
SETTING
STEAM
PLEASE
SELECT
Ⅲ Select a product key of your choice. In our example it is cappuc-
cino (Fig. 1/E).
Ⅲ The machine stops dispensing the programmed portion of steam
automatically.
CAPPUCCINO
WATER
100 ML
A bargraph indicates the duration of the steam dispensing
process.
Ⅲ Press P (Fig. 5/E) again to activate the setting programming step.
To stop the machine from dispensing steam prematurely,
press any of the product keys.
Ⅲ Press the «+» or «–» key until the required amount of water
appears on the display.
Ⅲ Press P (Fig. 5/E) to confirm your setting.
There might be some initial splashing when drawing off
steam. The pivoting steam spout becomes hot. Avoid direct
contact with the skin!
CONFIRMED
CAPPUCCINO
13. Switching the machine off
FROTH
20 SEC
COFFEE READY
Ⅲ Press P (Fig. 5/E) again to activate the programming step.
Ⅲ Press the «+» or «–» key to define the amount of frothed milk.
Ⅲ Switch the machine off using the ON / OFF key (Fig. 5/A). The
machine automatically performs a rinsing cycle when you switch
it off. Only the spouts and nozzles that were used are rinsed.
Ⅲ Press P to confirm your setting (Fig. 5/E).
CAPPUCCINO
GOOD-BYE
MILK
20 SEC
Ⅲ Press P (Fig. 5/E) again to activate the programming step.
Use the power switch on the rear of the machine (Fig. 15/D)
to disconnect the machine from the mains supply.
Ⅲ Press the «+» or «–» key to define the amount of frothed milk.
Ⅲ Press P to confirm your setting (Fig. 5/E).
Ⅲ Press the «+» or «–» key until POWDER appears on the display.
CAPPUCCINO
Ⅲ Press P (Fig. 5/E) again to activate the programming step.
Ⅲ Press the «+» or «–» key to set the coffee strength.
10
Ⅲ Press P to confirm your setting (Fig. 5/E).
Ⅲ Press the «+» or «–» key until MACHINE ON appears on the
display.
CAPPUCCINO
UNIT ON
GRINDER
50% 50%
—:—
Ⅲ Press P again (Fig. 5/E) to activate the MACHINE ON program-
Ⅲ Press P (Fig. 5/E) again to activate the programming step.
ming step.
Ⅲ Press the «+» or «–» key to define the left and the right grinder.
UNIT ON
Ⅲ Press P to confirm your setting (Fig. 5/E).
HOURS
—:—-
CAPPUCCINO
TEMP.
NORMAL
Ⅲ Press the «+» or «–» key to set the hours.
UNIT ON
Ⅲ Press P (Fig. 5/E) again to activate the programming step.
HOURS
07:00
Ⅲ Press the «+» or «–» key to set the temperature.
Ⅲ Press P to confirm your setting (Fig. 5/E).
Ⅲ Press EXIT (Fig. 5/K).
Ⅲ Press P to confirm your setting (Fig. 5/E).
UNIT ON
SETTING
E
MINUTES
07:00
Ⅲ Press the «+» or «–» key to set the minutes.
PLEASE
SELECT
Ⅲ Press EXIT (Fig. 5/K) to leave this programming step or select
the next product key.
UNIT ON
MINUTES
07:30
14.3 Setting the time
Ⅲ Press P to confirm your setting (Fig. 5/E).
CONFIRMED
COFFEE READY
Ⅲ Press P (Fig. 5/E) until you hear an acoustic signal.
UNIT ON
HARDNESS
07:30
Ⅲ Press the «+» or «–» key to select the next program step or press
EXIT (Fig. 5/K) to leave programming mode.
Ⅲ Press the «+» or «–» key until TIME appears on the display.
TIME
If —:— appears on the display, the switch-on function is
deactivated.
12:00
Ⅲ Press P again (Fig. 5/E) to activate the TIME programming step.
TIME
14.5 Automatic switch-off time
HOURS
12:00
You can program the automatic switch-off time. Choose a
time between 0.5 and 9.0 hours or —.— (inactive).
Ⅲ Press the «+» or «–» key to set the hours.
TIME
COFFEE READY
HOURS
14:00
Ⅲ Press P (Fig. 5/E) until you hear an acoustic signal.
Ⅲ Press P to confirm your setting (Fig. 5/E).
HARDNESS
TIME
MINUTES
14:00
Ⅲ Press the «+» or «–» key to set the minutes.
Ⅲ Press the «+» or «–» key until OFF AFTER appears on the
display.
TIME
OFF AFTER
MINUTES
14:45
Ⅲ Press P to confirm your setting (Fig. 5/E).
5.0 HRS
Ⅲ Press P again (Fig. 5/E) to activate the OFF AFTER program-
ming step.
CONFIRMED
OFF AFTER
5.0 HRS
Ⅲ Press the «+» or «–» key to define after how many hours your
machine should switch off.
TIME
14:45
Ⅲ Press the «+» or «–» key to select the next program step or press
EXIT (Fig. 5/K) to leave programming mode.
OFF AFTER
9.0 HRS
Ⅲ Press P to confirm your setting (Fig. 5/E).
CONFIRMED
14.4 Automatic switch-on time
COFFEE READY
OFF AFTER
9.0 HRS
Ⅲ Press the «+» or «–» key to select the next program step or press
EXIT (Fig. 5/K) to leave programming mode.
Ⅲ Press P (Fig. 5/E) until you hear an acoustic signal.
HARDNESS
11
14.6 Programming the language
SETTINGS
UNIT
ML
COFFEE READY
Ⅲ Press the EXIT key (Fig. 5/K) for with «+» or «–» key to select
the next program step.
Ⅲ Press P (Fig. 5/E) until you hear an acoustic signal.
HARDNESS
Ⅲ Press EXIT (Fig. 5/K) again to leave programming mode.
Ⅲ Press the «+» or «–» key until LANGUAGE appears on the
display.
14.7.2 Time format
This setting allows you to select the time format (24 hours or
AM/PM).
LANGUAGE
GERMAN
Ⅲ Press P again (Fig. 5/E) to activate the LANGUAGE program-
COFFEE READY
ming step.
Ⅲ Press P (Fig. 5/E) until you hear an acoustic signal.
LANGUAGE
GERMAN
Ⅲ Press the «+» or «–» key to select the required language.
HARDNESS
LANGUAGE
Ⅲ Press the «+» or «–» key until DISPLAY appears on the display.
ENGLISH
Ⅲ Press P to confirm your setting (Fig. 5/E).
SETTINGS
CONFIRMED
Ⅲ Press P again (Fig. 5/E) to activate the DISPLAY programming
step.
SETTINGS
LANGUAGE
UNIT
ML
ENGLISH
Ⅲ Press the «+» or «–» key to select the next program step or press
EXIT (Fig. 5/K) to leave programming mode.
Ⅲ Press the «+» or «–» key until TIME FORMAT appears on the
graphics display.
Ⅲ Press EXIT (Fig. 5/K) again to leave programming mode.
SETTINGS
TIME
FORMAT
14.7 Setting up the display
Ⅲ Press P again (Fig. 5/E) to activate TIME FORMAT.
14.7.1 Unit of measurement (ml/oz)
SETTINGS
This setting allows you to select a unit of measurement
(ml or oz).
FORMAT
24 HRS
Ⅲ Press the «+» or «–» key to select the required time format.
COFFEE READY
SETTINGS
FORMAT
AM/PM
Ⅲ Press P (Fig. 5/E) until you hear an acoustic signal.
HARDNESS
Ⅲ Press P to confirm your setting (Fig. 5/E).
CONFIRMED
Ⅲ Press the «+» or «–» key until DISPLAY appears on the display.
SETTINGS
SETTINGS
TIME
FORMAT
Ⅲ Press P again (Fig. 5/E) to activate the DISPLAY programming
step.
Ⅲ Press the EXIT key (Fig. 5/K) for with «+» or «–» key to select
the next program step.
SETTINGS
UNIT
ML
Ⅲ Press EXIT (Fig. 5/K) again to leave programming mode.
Ⅲ Press P again (Fig. 5/E) to activate the selected unit of measure-
ment.
14.8 Information
SETTINGS
With the IMPRESSA X9 you can check each coffee you
made. You can also check the number of cleaning cycles,
decalcifying cycles and Claris filter replacements you per-
formed.
UNIT
ML
Ⅲ Press the «+» or «–» key to select the required unit of measure-
ment.
COFFEE READY
SETTINGS
UNIT
OZ
Ⅲ Press P (Fig. 5/E) until you hear an acoustic signal.
Ⅲ Press P to confirm your setting (Fig. 5/E).
HARDNESS
CONFIRMED
Ⅲ Press the «+» or «–» key until INFORMATION appears on the
display.
12
16.2 Installing a fixed water supply system
INFORMATION
Please refer to the operating instructions for the fixed water supply
system or contact your JURA dealer.
Ⅲ Press P (Fig. 5/E) to activate the INFORMATION programming
step.
1 ESPRESSO
16.3 Emptying the coffee grounds container
The coffee grounds container collects the coffee grounds.
GROUNDS
200
PRODUCTS
Ⅲ Press the «+» or «–» key to select the required item of infor-
mation.
EMPTY
Ⅲ If this information is displayed, the machine will no longer make
coffee. The grounds container needs to be emptied.
You can leave the INFORMATION menu any time by
pressing EXIT (Fig. 5/K).
Ⅲ Carefully take out the drip tray; it is filled with water. Remove
the grounds container (Fig. 9/ A).
Ⅲ Press the «+» or «–» key to select the next program step or press
EXIT (Fig. 5/K) to leave programming mode.
Under TOTAL you will find all the products made (coffee,
hot water and steam)
E
16.4 Emptying the drip tray
DRIP TRAY
EMPTY
Ⅲ If this information is displayed, the machine will no longer make
coffee. The drip tray needs to be emptied.
15. Counter
The single counter allows you to record your consumption
over a defined period of time. This counter can be reset to 0
at any point in time.
Ⅲ Carefully take out the drip tray; it is filled with water (Fig. 9/B).
16.5 Grounds bin missing
COFFEE READY
GROUNDS BIN
Ⅲ Press Counter (Fig. 5/D) until you hear an acoustic signal.
MISSING
Ⅲ If this message lights up, the grounds bin is not installed properly
1 ESPRESSO
or missing altogether.
150
PRODUCT
Ⅲ Press the «+» or «–» key to select a product.
16.6 Filling the bean tank
Ⅲ The display will indicate the number of times this product was
made.
COFFEE READY
Ⅲ Press EXIT (Fig. 5/K) to leave the COUNTER.
FILL
BEANS
Reset counter:
The display dialog system indicates which of the two bean tanks is
empty. Fill tank with beans as described in Chapter 3.4.
COUNTER
RESET
NO
The bean level is monitored electronically on the IMPRES-
SA X9. To ensure smooth operation, we recommend that you
regularly clean the bean tanks with a dry cloth. Switch the
machine off with the ON / OFF key (Fig. 5/A) before you do
so.
Ⅲ Press the «+» or «–» key until the display indicates
COUNTER
RESET
YES
Ⅲ Press P to confirm your selection (Fig. 5/E).
Ⅲ Switch the machine off with the power switch on the rear of the
machine (Fig. 15/D).
RESET
16.7 Removing stones
Ⅲ Open the programming door on the front (Fig. 4) and switch the
IMPRESSA X9 off with the ON / OFF key (Fig. 5/A).
16. Maintenance
Ⅲ Switch the machine off with the power switch on the rear of the
machine (Fig. 15/D) and disconnect it from the mains supply.
16.1 Filling the water tank
WATER TANK
Ⅲ Open the hinged door on reverse of the machine (Fig. 10).
FILL
Ⅲ If this message is displayed, the machine will no longer make
coffee/hot water. Refill water as described in Chapter 3.3.
Ⅲ Push sliders to the rear (Fig. 10) and take the bean tank out of the
machine.
Ⅲ Remove any beans with a vacuum cleaner.
Ⅲ Insert the key (Fig. 11).
The water tank should be rinsed out and filled with fresh
water daily. When using a fixed water supply system, we
recommend regularly rinsing the water tank and filling it
with fresh water.
Ⅲ Now turn the key counter-clockwise until the jammed stone is
released.
Ⅲ Remove any remaining powder with a vacuum cleaner.
Ⅲ Re-install the bean tank and pull the sliders to the front before
closing the door (Fig. 10).
13
16.8 General cleaning instructions
MACHINE CLEA
Ⅲ Never use sharp objects or caustic chemicals for cleaning.
Ⅲ Clean the inside and outside of the case using a soft, damp cloth. COFFEE READY
Ⅲ Clean the pivoting steam spout (V) each time it was used.
Ⅲ After heating milk, draw off some steam to clean the inside of
the pivoting steam spout (V).
Always dip both milk hoses into the fluid (Fig. 8/B).
Ⅲ The water tank should be rinsed out and filled with fresh water
daily.
16.11 Cleaning the coffee system
Visible calcification in the water tank can be removed using
a commercial decalcifying agent. Take out the water tank
(Fig.2).
Once started, the cleaning process must not be interrupted. It takes
approx. 15 minutes.
If you are using a CLARIS plus filter cartridge, remove it
before decalcifying the tank.
COFFEE READY
CLEAN
After having dispensed 220 products or after 80 rinsing cy-
cles, the machine must be cleaned. The machine will still
make coffee or hot water/steam. However, we recommend
that you run a cleaning cycle within the same day. After hav-
ing made another 20 coffees the cleaning alarm flashes, and
after yet another 20 coffees, the display will indicate the fol-
lowing message:
16.9 Disassembling and cleaning the dual spout
We recommend to disassemble and clean the dual spout if
you make milk products regularly.
Ⅲ Remove the cover of the height-adjustable dual spout by pressing
the Unlock key (Fig. 12) and remove the coffee distributor (Fig.
13).
CLEAN NOW
Ⅲ Take off the spouts (Fig. 13).
Ⅲ Take the spouts apart (Fig. 14).
Ⅲ Open the programming door (Fig. 4) and press the Clean Coffee
System key (Fig. 5/I) until you hear an acoustic signal.
Ⅲ Thoroughly rinse all the parts with warm water.
Ⅲ Reassemble the parts (Fig. 14).
EMPTY
TRAY
When assembling the dual spout, note the colour of the indi-
vidual parts (Fig. 14).
EMPTY
COFFEE
BIN
Ⅲ Attach the spouts to the IMPRESSA X9 (Fig. 13).
Ⅲ Put back the cover, making sure it locks into place (Fig. 13).
Ⅲ Remove the tray and the grounds bin and EMPTY the coffee
grounds.
Use corresponding brushes for carrying out the cleaning
steps described in sections above.
COFFEE BIN
MISSING
Ⅲ Place the grounds bin and the tray back into the machine.
16.10 Cleaning the milk system
PRESS
KEY
We recommend to clean the milk system daily.
Ⅲ Place a sufficiently large receptacle under the height-adjustable
Once started, the cleaning process must not be interrupted. It takes
approx. 2 minutes.
dual spout (Fig. 6).
Ⅲ Press the Clean Coffee System key (Fig. 5/I) until you hear an
acoustic signal.
Ⅲ Open the programming door on the front (Fig. 4).
MACHINE CLEA
Ⅲ Press the Clean Milk System key (Fig. 5/H) until you hear an
acoustic signal.
Ⅲ You will hear an acoustic signal.
CLEANER FOR
ADD TABLET
PRESS
KEY
PRESS
KEY
Ⅲ Place a receptacle with a capacity of at least 0.5 litres under the
height-adjustable dual spout (Fig. 6).
Ⅲ Drop an original JURA cleaning tablet into the filler funnel
(Fig. 16).
Ⅲ Fill a receptacle with approx. 4 dl of water and add 1 1/2 capfuls
of JURA cappuccino cleaning agent. Dip the two milk hoses into
this solution (Fig. 8/B).
Ⅲ Press the Clean Coffee System key (Fig. 5/I).
MACHINE CLEA
Ⅲ Press the Clean Milk System key (Fig. 5/H).
Ⅲ You will hear an acoustic signal.
MACHINE CLEA
EMPTY
TRAY
Ⅲ You will hear an acoustic signal.
WATER FOR C
EMPTY
PRESS
KEY
COFFEE
BIN
Ⅲ Remove the tray and the grounds bin and EMPTY the coffee
grounds.
Fill a receptacle with approx. 4 dl of fresh water and dip the
milk hoses into it (Fig. 8/B).
COFFEE BIN
MISSING
Ⅲ Press the Clean Milk System key (Fig. 5/H).
14
Ⅲ Place the grounds bin and the tray back into the machine.
EMPTY
TRAY
EMPTY
COFFEE
COFFEE READY
BIN
Ⅲ Remove the tray and the grounds bin and EMPTY the coffee
16.12 Cleaning the dual spout
grounds.
Once started, the cleaning process must not be interrupted. It takes
approx. 20 minutes.
COFFEE BIN
MISSING
Ⅲ Place the grounds bin and the tray back into the machine.
COFFEE READY
CLEAN
COFFEE READY
After having dispensed 220 products or after 80 rinsing
cycles, the machine must be cleaned. The machine will still
make coffee or hot water/steam. However, we recommend
that you run a cleaning cycle within the same day. After
having made another 20 coffees the cleaning alarm flashes,
and after yet another 20 coffees, the display will indicate the
following message:
16.13 Changing the filter
E
After 50 litres of water, the CLARIS plus filter cartridge will
need to be replaced. If the capacity exceeds 5%, a message
on the display will prompt you to change the filter. If it
exceeds 10%, the display will read CHANGE NOW
CLEAN NOW
COFFEE READY
Ⅲ Open the programming door (Fig. 4) and press Clean Dual Spout
(Fig. 5/J) until you hear an acoustic signal.
CHANGE
FILTER
EMPTY
TRAY
Ⅲ Open the programming door (Fig. 4) and press the Filter key
(Fig. 5/B).
EMPTY
INSERT FILTE
COFFEE
BIN
PRESS
WATER
Ⅲ Remove the tray and the grounds bin and EMPTY the coffee
grounds.
Ⅲ EMPTY the water tank and insert the filter cartridge in the tank
together with the cartridge holder, applying gentle pressure. Push
the cartridge holder into position until it engages audibly (Fig.
17).
COFFEE BIN
MISSING
Ⅲ Place the grounds bin and the tray back into the machine.
Ⅲ Fill the water tank with cold, fresh tap water and reinstall it in
the machine.
CLEANER FOR
Ⅲ Place a sufficiently large receptacle under the pivoting hot water
spout (U).
PRESS
KEY
Ⅲ Press the Hot Water key (T / ).
Ⅲ Place a sufficiently large receptacle under the height-adjustable
dual spout (Fig. 6).
FILTER RINSE
Ⅲ Fill a receptacle with approx. 4 dl of water and add 1 1/2 capfuls
of JURA cappuccino cleaning agent. Dip the two milk hoses into
the solution (Fig. 8/B).
Ⅲ The flow of water stops automatically.
COFFEE READY
Ⅲ Press the Clean Dual Spout key (Fig. 5/J).
MACHINE CLEA
The water might be slightly discoloured (no hazard to
health).
Ⅲ You will hear an acoustic signal.
ADD TABLET
PRESS
KEY
16.14 Decalcifying
Once started, the decalcifying program must not be interrupted. It
takes approx. 40 minutes.
Ⅲ Drop an original JURA cleaning tablet into the filler funnel
(Fig. 16).
Ⅲ Press the Clean Dual Spout key (Fig. 5/J).
When using acidic decalcifying agents, immediately remove
any splashes or drops from sensitive surfaces, in particular
surfaces made of natural stone or wood, or take appropriate
preventive measures.
MACHINE CLEA
Ⅲ You will hear an acoustic signal.
WATER FOR C
COFFEE READY
DESCALE
PRESS
KEY
We recommend that you decalcify the machine within the
same day. If you make more coffees, the display will indicate
DECALCIFY. After yet even more coffees made, the display
will read DECALCIFY NOW.
Fill a receptacle with approx. 0.4 litres of fresh water and dip
the milk hoses into it (Fig. 8).
Ⅲ Press the Clean Dual Spout key (Fig. 5/J).
Ⅲ Open the programming door on the front (Fig. 4) and press the
MACHINE CLEA
Decalcify key (Fig. 5/C).
Ⅲ You will hear an acoustic signal.
EMPTY
TRAY
15
16.15 Cleaning the grinder and the bean tank
EMPTY
COFFEE
BIN
Ⅲ Switch off the machine by pressing the ON/OFF key (Fig.5/A)
Ⅲ Disconnect the machine from power supply (Fig. 15/D)
Ⅲ Open the flap (Fig. 10) on the back of the machine
Ⅲ Push back the slides (Fig. 10)
Ⅲ Remove the tray and the grounds bin and EMPTY the coffee
grounds.
COFFEE BIN
Ⅲ Remove the bean tanks by turning them (Fig. 10)
Ⅲ Remove bean residues using the vacuum cleaner.
MISSING
Ⅲ Place the grounds bin and the tray back into the machine.
Ⅲ Completely dissolve 3 original JURA descaling tablets in 0.7
litres of water and pour the solution into the empty water tank.
17. Tips for perfect coffee
SOLVENT IN T
Height-adjustable dual spout
You can adjust the height-adjustable dual spout to the size of your
cups.
PRESS
KEY
Place 3 sufficiently large receptacles under the height-
adjustable dual spout, the steam spout and the hot water
spout (Fig. 18, 1/2 litre receptacle each).
Grinding
Please refer to Capter 7 “Setting the grinding degree”.
Individual programming for perfect coffee
Please refer to Chapter 14.2. Customizing (product definition).
Ⅲ Press the Decalcify key (Fig. 5/C).
MACHINE DECA
Pre-warm cups
You can warm the cups in advance with hot water or stream. The
smaller the quantity of coffee, the more important the warming of
the cups.
Ⅲ You will hear an acoustic signal.
TRAY
EMPTY
Ⅲ Remove the tray and the grounds bin. EMPTY the coffee
grounds.
TRAY
MISSING
Ⅲ Place the grounds bin and the tray back into the machine.
WATER TANK
RINSE/F
Ⅲ Thoroughly rinse out the water tank and fill it with fresh tap
water.
Ⅲ Place the water tank back into the machine.
Place 3 sufficiently large receptacles under the height-
adjustable dual spout, the steam spout and the hot water
spout (Fig. 18, 1/2 litre receptacle each).
PRESS
KEY
Ⅲ Press the Decalcify key (Fig. 5/C).
MACHINE DECA
CAPPUCCINO
RINSING
Ⅲ You will hear an acoustic signal.
EMPTY
TRAY
EMPTY
COFFEE
BIN
Ⅲ Remove the tray and the grounds bin and EMPTY the coffee
grounds.
COFFEE BIN
MISSING
Ⅲ Place the grounds bin and the tray back into the machine.
COFFE READY
16
18. Messages
Display
Cause
Remedy
WATER TANK
FILL
The tank is empty.
Fill up with water.
The water level gauge in the tank is jammed.
Empty tank, rinse, fill water and
put it back.
The tank is calcified; the water level gauge is
clogged.
Take out tank, decalcify, rinse well, fill with
water and put it back.
SELECT PRODU
FILL
BEANS
The bean tank is empty.
Refill bean tank.
Message still lights up despite beans having
been refilled.
Make a cup of coffee.
E
Stone jammed in the system.
Remove stone as described in Chapter 16.7
“Removing stones”.
GROUNDS
EMTY
The grounds bin is full.
Take out and empty tray and grounds bin.
Empty tray and place it back into machine.
Insert tray properly.
TRAY
EMTY
The tray is full.
TRAY
The tray is not properly engaged.
The grounds bin is not installed.
200 products dispensed or 80 rinsing cycles run.
MISSING
GROUNDS BIN
MISSING
Install grounds bin.
SELECT PRODU
CLEAN
Clean according to Chapter 16.12.
Cleaning cycle completed but message still
lighting up.
Run cleaning cycle again but without
cleaning tablet.
SELECT PRODU
DESCALE
Machine needs to be decalcified.
Decalcify machine as described in
Chapter 16.14.
Decalcifying cycle completed but message still
lighting up.
Run decalcifying cycle again using water only
(no decalcifying agent).
SELECT PRODU
FILLTER
CHANGE
The filter is no longer effective.
Change filter as described in Chapter 16.13.
CHECK BEAN
CONT-
AINER
The bean container is not correctly inserted.
Insert bean container correctly.
The slides have not been pulled out.
The bean container slides are closed.
Make sure that the sliders have been
pulled right out.
Bean containers are very dirty.
Clean bean container as described in
section 16.15.
ERROR
Please contact your local service partner.
17
19. Disposal
21. Technical data
Please dispose of old machines in an environmentally
compatible way
Old machines contain valuable materials capable of being
recycled which should be salvaged for recycling. Please
therefore dispose of old machines via suitable collection
systems.
Version «CH»
Voltage:
230 V AC
1500 W
10 A
Output:
Fuse:
Safety check:
20. Legal information
Pump pressure:
2 x max. 15 bar
5.0 liters
These operating instructions contain all the information necessary
for the correct use, operation and maintenance of your machine.
Understanding and complying with the directives contained in
these operating instructions are essential for the machine without
risk and also for safety during operation and maintenance. These
opperating instructions cannot cover all imaginable users of the
machine.
Water tank:
Capacity, bean container:
Capacity, grounds container:
Cable length:
2x 650 gr
max. 40 port.
approx. 1.8 m
20.5 kg
Weight:
We would further point out that the contents of these operating
instructions in no way constitute a part of or amend any previous or
existing contract, agreement or legal relationsship. All obligations
on the part of JURA Elektroapparate AG result from the sales
agreement question, which also contains the complete details of the
valid warranty terms. These contractual warranty terms are neither
extended nor limitet in any way by information contained in these
operating instructions.
These operating instructions contain information protected by
copyright. Photocoping or translation into another language with-
out the prior written approval of JURA Elektroapparate AG are not
admissible.
Dimensions (B x H x D):
43 x 58.5 x 51 cm
Version «International»
Voltage:
Output:
230 V AC
2200 W
15 A*
Fuse:
Safety check:
Pump pressure:
2 x max. 15 bar
5.0 liters
Water tank:
Capacity, bean container:
Capacity, grounds container:
Cable length:
2x 650 gr
max. 40 port.
approx. 1.8 m
20.5 kg
Weight:
Dimensions (B x H x D):
43 x 58.5 x 51 cm
* During the preparation of draw-offs of coffee, steam can also be
drawn of.
18
|