Jura Capresso 95 User Manual

IMPRESSA XS90/95  
Instructions for use  
9/05  
Fig. 1  
Fig. 5  
Fig. 9  
Fig. 13  
Fig. 2  
Fig. 3  
Fig. 4  
Fig. 8  
Fig. 12  
Fig. 6  
Fig. 7  
2
3
1
Fig. 10  
Fig. 11  
Fig. 14  
Fig. 15  
Description of the machine  
16  
17  
18  
1. Drip tray  
2. Drip grate  
15  
14  
3. Programming door  
4. Rotary Switch  
5. Selection key for pre-ground coffee  
6. Coffee à la Carte key  
7. 1 Coffee key  
19  
20  
21  
13  
12  
11  
8. 2 Coffees key  
10  
9. 1 Espresso key  
9
8
22  
23  
24  
25  
10. 2 Espressos key  
7
11. ON / OFF key  
12. Rinse key  
13. Display dialog system  
14. Water tank with handle  
15. Aroma preservation cover  
16. Bean tank cover  
3
17. Lid for pre-ground coffee filler funnel  
18. Height-adjustable coffee spout  
19. Heatable cup shelf  
20. Constant Steam key  
21. Steam Portion key  
22. Hot Water switch  
23. Pivoting steam spout  
24. 2-stage frothing jet  
25. Height-adjustable hot water spout  
26. Coffee grounds bin  
27. Power switch  
27  
6
5
4
26  
2 1  
Contents  
13.3 Maintenance ............................................page 14  
13.4 Programming the amount of powder for coffee  
1. Safety information ..............................................page  
6
6
6
6
6
6
7
7
7
7
7
8
8
9
9
9
1.1  
1.2  
Warnings ................................................page  
and espressso............................................page 14  
Precautions..............................................page  
13.5 Setting the amount of water for coffee,  
2. Before you start using the IMPRESSA ....................page  
espresso and coffee à la carte........................page 15  
2.1  
2.2  
2.3  
2.4  
2.5  
2.6  
Checking the mains voltage ..........................page  
Checking electrical fuse...............................page  
Filling the water tank .................................page  
Filling the bean tank...................................page  
Adjusting the grinding gear ..........................page  
Power switch............................................page  
13.6 Programming the temperature for coffee,  
espresso and coffee à la carte........................page 16  
13.7 Programming the water portion.....................page 16  
13.8 Programming the steam portion ....................page 16  
13.9 Economy mode..........................................page 17  
13.10 Setting the time ........................................page 18  
13.11 Programming the automatic switch-on time......page 18  
13.12 Programming the automatic switch-off time .....page 19  
13.13 Programming the language ..........................page 19  
13.14 Programming the display.............................page 20  
13.15 Information..............................................page 20  
14. Lock functions....................................................page 21  
14.1 Locking/releasing the drawing of coffee  
3. First use ...........................................................page  
3.1  
Cup illumination........................................page  
4. Adjusting your machine to the water hardness.............page  
5. Using a CLARIS plus filter cartridge........................page  
5.1  
5.2  
Installing the filter.....................................page  
Changing the filter .....................................page  
6. Rinsing the machine.............................................page 10  
7. Making coffee (1 espresso, 2 espressos, 1 coffee,  
à la carte.................................................page 21  
E
2 coffees)..........................................................page 10  
7.1. Making coffee with pre-ground coffee powder....page 10  
8. Making coffee à la carte .......................................page 11  
9. Making hot water................................................page 11  
10. Drawing off steam ...............................................page 12  
11. Frothing milk.....................................................page 12  
11.1 Frothing one portion of milk (with the  
14.2 Locking the programming function.................page 21  
15. Maintenance......................................................page 21  
15.1 Filling the water tank .................................page 21  
15.2 Emptying the coffee grounds.........................page 22  
15.3 Emptying the drip tray................................page 22  
15.4 Drip tray missing.......................................page 22  
15.5 Filling the bean tank...................................page 22  
15.6 Removing stones from the grinding gear ..........page 22  
15.7 Changing the filter .....................................page 23  
15.8 Prompt to run cleaning cycle ........................page 23  
15.9 Prompt to run decalcifying cycle....................page 23  
15.10 Emptying the system ..................................page 23  
15.11 General cleaning instructions ........................page 24  
16. Cleaning ...........................................................page 24  
17. Decalcifying.......................................................page 25  
18. Disposal............................................................page 26  
19. Tips for perfect coffee...........................................page 26  
20. Problems ..........................................................page 27  
21. Legal information ...............................................page 28  
22. Technical data....................................................page 28  
2-stage frothing jet) ...................................page 12  
11.2 Frothing milk (with the 2-stage frothing jet) .....page 12  
11.3 Attaching the Professional-Cappuccino Frother  
to the IMPRESSA .....................................page 13  
11.4 Making cappuccino and hot milk with the  
Professional-Cappuccino Frother ...................page 13  
11.5 Cleaning the Professional-Cappuccino Frother  
and jet....................................................page 13  
12. Switching the IMPRESSA off ................................page 13  
13. Programming.....................................................page 14  
13.1 Programming the filter ...............................page 14  
13.2 Programming your machine to the correct  
water hardness (only with FILTER NO) ...........page 14  
5
Never immerse the IMPRESSA in water.  
Before you begin  
Congratulations on having bought this IMPRESSA!  
1.2.Precautions  
In order to ensure perfect operation of your IMPRESSA, carefully  
read this operating manual and keep it for future reference.  
Should you need more information or meet with particular prob-  
lems not specified in these operating instructions in sufficient  
detail, please contact JURA Elektroapparate AG directly or your  
local authorized dealer.  
Never expose the coffee machine to weather (rain, snow, frost),  
never touch the machine when your hands are wet.  
Place the IMPRESSA on a firm, level base that is resistant to any  
water that may leak. Never stand on hot or warm surfaces (oven  
hobs). Keep out of the reach of children.  
If you intend not to use the machine for a longer time (holidays,  
etc.), always turn off the power switch.  
You will also find useful tips on operation and maintenance  
Don’t forget to check out the knowledge builder – our ani-  
mated operating instructions. LEO, our assistant, will take  
you through all the functions.  
Always turn off the power switch before cleaning the machine.  
When disconnecting the mains cable, never pull on the mains  
cable or the machine itself.  
The IMPRESSA is connected to the mains supply via a mains  
cable. Make sure nobody can trip over the mains cable. Keep out  
of reach of children and pets.  
Never put the coffee machine or parts of it into a dishwasher.  
Make sure to install the machine at a place with sufficient air  
circulation to prevent it from overheating.  
1. Safety information  
1.1 Warnings  
2. Before you start using the IMPRESSA  
2.1 Checking the mains voltage  
Children are not aware of the dangers involved in using electric  
appliances. Therefore, never leave the machine unattended with  
unsupervised children around.  
The coffee machine is preset to the correct mains voltage. Check if  
your local mains supply voltage complies with the information giv-  
en on the type plate on the underside of the coffee machine.  
The coffee machine must only be used by persons who know  
how to operate it.  
Never use a defective machine or a machine with a defective  
mains cable.  
2.2 Checking electrical fuse  
Never repair or open the coffee machine yourself. Repairs may  
only be carried out by authorized service shops using original  
spare parts and accessories.  
The machine is designed for an electric current of 10 amperes.  
Check if the electrical fuse has sufficient capacity.  
6
Open the lid of the bean tank (16).  
2.3 Filling the water tank  
To adjust the grinding degree, turn the Rotary Switch (Fig. 2) to  
the required position.  
Only use fresh, cold water. Never fill the water tank with  
milk, mineral water or other liquids.  
The smaller the dots, the finer the grind  
The larger the dots, the coarser the grind  
Take out the water tank and thoroughly rinse it out with cold tap  
water.  
2.6 Power switch  
Then fill it with water and place it back into the coffee machine.  
Make sure the tank is installed correctly and that it engages  
properly.  
Actuate the power switch (27) on your IMPRESSA before  
using the machine for the first time.  
We recommend that you switch off your IMPRESSA with  
the power switch (27) if you intend not to use the machine  
for longer periods of time (e.g.during holidays)  
2.4 Filling the bean tank  
To ensure your IMPRESSA will have a long service life and  
to avoid repairs, please note that the grinding gear is not suit-  
able for coffee beans that have been treated with additives  
(e.g. sugar) during or after roasting. Coffee blends of this  
type may damage the machine’s grinding gear. Repair costs  
resulting from such use are not subject to the terms of guar-  
antee.  
3. First use  
Press the power switch (27) on the back (bottom left) of the  
machine (Fig. 3).  
E
The ON / OFF key  
(11) lights up to indicate that the machine  
has been switched on with the power switch.  
Open the cover of the bean tank (Fig. 2) and remove the aroma  
Switch the machine on using the ON / OFF key  
(11). The  
preservation cover (15).  
light of the ON / OFF key goes off.  
Remove any dirt or foreign matter from the bean tank.  
Open the programming door (3).  
Fill the bean tank with coffee beans (Fig. 2), replace the aroma  
LANGUAGE  
ENGLISH  
preservation cover (15) and close the lid.  
Turn the Rotary Switch (4) until the required language is dis-  
played.  
2.5 Adjusting the grinding gear  
You can adjust the grinding gear to the roast of your coffee. We  
recommend that you use:  
Example:  
LANGUAGE  
ENGLISH  
a finer setting for a lighter roast  
a coarser setting for a darker roast  
Confirm your selection by pressing the Rotary Switch (4).  
FILL SYSTEM / PRESS STEAM  
The grinding degree may only be adjusted while the grinding  
gear is running.  
7
Place a receptacle under the 2-stage frothing jet (24) and press  
one of the Steam keys  
4. Adjusting your machine to the water hardness  
.
The IMPRESSA heats up water. As a result, calcification  
occurs during normal use. This is indicated automatically.  
The IMPRESSA must therefore be adjusted to the hardness  
of the water used. Use the supplied test sticks to determine  
the water hardness or contact your local waterworks.  
The system now fills up automatically. A little water will leak  
from the frothing jet.  
SYSTEM FILLING  
HEATING UP  
PRESS RINSE  
1° German hardness is equivalent to 1.79° French hardness.  
Place a cup under the height-adjustable coffee spout (18).  
Press Rinse  
.
The water hardness programming step is no longer displayed  
if the filter is activated.  
MACHINE RINSING  
Now the water lines are flushed with fresh water. A little water  
will leak from the coffee spout (18).  
The IMPRESSA is preset to 16°dH. This setting can be changed.  
To do so, proceed as follows:  
SELECT PRODUCT  
You can now make a product of your choice by pressing the  
corresponding key.  
SELECT PRODUCT  
Open the programming door (3). Press the Rotary Switch (4)  
until you hear an acoustic signal.  
If FILL BEANS appears on the display, press one of the  
coffee product keys again. The grinder is not yet completely  
filled with coffee beans.  
FILTER NO  
Turn the Rotary Switch (4) until the following message is dis-  
played:  
For a perfect frothing result, adjust the height-adjustable  
coffee spout (18) to the size of your cup (Fig. 4).  
HARDNESS  
16°dH  
Now press the Rotary Switch (4) to start programming.  
3.1 Cup illumination  
16°dH  
The cup illumination puts your coffee in a good light, making it a  
treat for the eyes as well.  
When you switch on the IMPRESSA or press any key, the cup illu-  
mination is activated for 1 minute.  
ⅥⅥⅥⅪⅪ  
Now turn the Rotary Switch (4) until the required water hardness  
is set.  
20°dH (example)  
ⅥⅥⅥⅥⅪ  
Confirm the selected setting by pressing the Rotary Switch (4).  
HARDNESS  
20°dH (example)  
8
Now turn the Rotary Switch (4) until the following message is  
Close the cartridge holder until it engages audibly.  
displayed:  
Fill the water tank (14) with cold, fresh tap water and place it  
EXIT  
Now press the Rotary Switch (4) to leave the programming mode.  
SELECT PRODUCT  
back into the machine.  
Place a sufficiently large receptacle (min. 0.5 litres) under the  
pivoting steam spout (23) and press one of the Steam keys  
to start the filter rinsing process.  
FILTER RINSING  
5. Using a CLARIS plus filter cartridge  
Filter rinsing stops automatically.  
When using the CLARIS plus filter cartridge correctly, de-  
calcifying your IMPRESSA will no longer be necessary. For  
more information on the CLARIS plus filter cartridge refer  
to the brochure “CLARIS plus. Hard on limescale. Gentle on  
your coffee machine.”  
SELECT PRODUCT  
You have now activated the filter. The programming step for  
adjusting your machine to the correct water hardness is  
therefore no longer displayed.  
5.1 Installing the filter  
The water might be slightly discoloured (no hazard to  
health).  
Open the programming door (3). Press the Rotary Switch (4) un-  
til you hear an acoustic signal.  
E
5.2 Changing the filter  
FILTER  
NO  
After 50 litres of water the filter cartridge will need to be  
replaced. The display will prompt you to change the filter.  
Please monitor the period of use of the CLARIS plus filter  
cartridge (max. 2 months) using the scale on the cartridge  
holder by the water tank.  
Now press the Rotary Switch (4) to start programming.  
Turn the Rotary Switch (4) until the following message is dis-  
played:  
FILTER  
YES  
SELECT PRODUCT / CHANGE FILTER  
The Rinse key lights up. Press Rinse  
INSERT FILTER / PRESS STEAM  
Confirm your setting by pressing the Rotary Switch (4).  
.
INSERT  
FILTER / PRESS STEAM  
Remove the water tank (14) from the IMPRESSA. Empty out  
any remaining water. Fold up the cartridge holder (Fig. 1).  
Attach the extension piece to the top of the CLARIS plus filter  
cartridge. Now insert the filter cartridge in the water tank, apply-  
ing gentle pressure (Fig. 1)  
Take out the water tank (14). Empty out any remaining water.  
Fold up the cartridge holder (Fig. 1). Attach the extension piece  
(contained in the Welcome Pack) to the top of the CLARIS plus  
filter cartridge. Now insert the filter cartridge in the water tank,  
applying gentle pressure (Fig. 1)  
Close the cartridge holder until it engages audibly.  
9
process (I.P.B.A.S.) moistens the coffee powder, briefly inter-  
rupts the flow of hot water and then begins with the actual brew-  
ing process.  
Fill the water tank (14) with cold, fresh tap water and place it  
back into the machine.  
Place a sufficiently large receptacle (min. 0.5 litres) under the  
pivoting steam spout (23) and press one of the Steam keys  
to start the filter rinsing process.  
1 ESPRESSO (example)  
NORMAL (example)  
The coffee brewing process stops automatically as soon as the  
FILTER RINSING  
set amount of water has run through.  
Filter rinsing stops automatically.  
SELECT PRODUCT  
SELECT PRODUCT  
To stop the brewing process prematurely, press any of the  
product keys.  
You can also trigger a change of filter manually from the  
Maintenance menu at any point in time (only if the filter has  
been activated) - see Chapter 13.3.  
You can change the amount of water while the machine is  
brewing coffee. Open the programming door. Turn the  
Rotary Switch (4) until the display indicates the required  
amount (ML). The amount of water can be selected in incre-  
ments of 5 ML.  
6. Rinsing the machine  
If the coffee machine is switched off and has cooled down,  
you will be prompted to start a rinsing cycle when switching  
the machine back on. The rinsing cycle starts automatically  
when you switch the machine off.  
The amounts given in ML are approximate values and may  
vary from the effective quantity.  
PRESS RINSE  
7.1. Making coffee with pre-ground coffee powder  
Place a cup under the coffee spout (18).  
Press Rinse  
.
Never use water-soluble instant coffee.  
MACHINE RINSING  
SELECT PRODUCT  
SELECT PRODUCT  
You can also trigger a rinsing cycle manually from the Main-  
tenance menu at any point in time (see Chapter 13.3).  
Place 1 or 2 cups (as required) under the coffee spout (18) and  
open the programming door (3). Press the selection key for pre-  
ground coffee  
FILL  
POWDER / SELECT PRODUCT  
.
7. Making coffee  
(1 espresso, 2 espressos, 1 coffee, 2 coffees)  
Now fill 1 or 2 level scoops of pre-ground coffee into the filler  
funnel for pre-ground coffee (17).  
SELECT PRODUCT  
Place 1 or 2 cups (as required) under the coffee spout (18) and  
press a key of your choice . The pre-brewing  
Then press a product key of your choice.  
,
,
,
10  
Turn the Rotary Switch (4) until the display indicates the desired  
coffee strength and press the Rotary Switch (4) to make the cof-  
fee. The pre-brewing process (I.P.B.A.S.) moistens the coffee  
powder, briefly interrupts the flow of hot water and then begins  
with the actual brewing process.  
1 ESPRESSO (example)  
POWDER  
The coffee brewing process stops automatically as soon as the  
set amount of water has run through.  
SELECT PRODUCT  
A LA CARTE  
XSTRONG (example)  
To stop the brewing process prematurely, press any of the  
product keys.  
The coffee brewing process stops automatically as soon as the  
set amount of water has run through.  
We recommend always using powder from fresh coffee  
beans or pre-ground, vacuum-packed coffee. Never fill in  
more than 2 scoops of powder. The filler funnel is no storage  
tank. Make sure the coffee powder you use is not too fine.  
This may block the system and cause the coffee only to drip  
out of the coffee spout.  
SELECT PRODUCT  
To stop the brewing process prematurely, press any of the  
product keys.  
You can change the amount of water while the machine is  
brewing coffee. To do so, turn the Rotary Switch (4) until the  
display indicates the required amount (ML). The amount of  
water can be selected in increments of 5 ML.  
If you have pressed the selection key  
unintentionally,  
press any of the product keys to cancel your selection.  
E
You can change the amount of water while the machine is  
brewing coffee. To do so, turn the Rotary Switch (4) until the  
display indicates the required amount (ML). The amount of  
water can be selected in increments of 5 ML.  
The amounts given in ML are approximate values and may  
vary from the effective quantity.  
9. Making hot water  
The amounts given in ML are approximate values and may  
vary from the effective quantity.  
SELECT PRODUCT  
Place 1 cup or 1 glass under the hot water spout (25) and turn the  
Hot Water switch (22) to  
.
8. Making coffee à la carte  
WATER  
PORTION  
SELECT PRODUCT  
The machine stops dispensing water automatically as soon as the  
set amount of water has been dispensed.  
Place 1 cup under the coffee spout (18) and open the program-  
ming door (3). Press the Coffee à la Carte key  
.
CLOSE TAP  
Turn the switch (22) back to  
SELECT PRODUCT  
A LA CARTE  
XMILD  
.
11  
To stop the process prematurely, turn the switch (22) back  
to  
Place a cup under the pivoting steam spout (23) and dip the  
2-stage frothing jet (24) in the milk to be frothed or the liquid to  
be heated.  
.
You can also change the amount of water set while the  
machine is brewing coffee. Open the programming door.  
Turn the Rotary Switch (4) until the display indicates the  
required amount (ML). The amount of water can be selected  
in increments of 5 ML.  
Press the Steam Portion key  
STEAM PORTION  
You can stop the process any time by pressing the Steam Portion  
key  
.
.
SELECT PRODUCT  
The amounts given in ML are approximate values and may  
vary from the effective quantity.  
You can set the duration of drawing off steam in 1-second  
increments with the Rotary Switch (4).  
10. Drawing off steam  
11. Frothing milk  
Make sure the nozzle has engaged properly. If the nozzle is  
clogged with dried milk or has not been attached properly, it  
might suddenly come off during operation.  
The IMPRESSA is ready to froth milk when both Steam key lights  
light up constantly.  
If the lights are off, press one of the two Steam keys  
.
To ensure perfect operation, clean the 2-stage frothing jet  
(24) regularly. Use the opening provided on the handle of the  
measuring spoon for the purpose to unscrew the 2-stage  
frothing nozzle (Fig. 14). Thoroughly rinse the 3 parts under  
running water.  
11.1 Frothing one portion of milk  
(with the 2-stage frothing jet)  
SELECT PRODUCT  
Pour milk into a jug or similar receptacle.  
Steam can be used for heating liquids and frothing milk for  
cappuccino. When heating liquids, make sure the 2-stage  
frothing jet (24) is pushed up. To froth liquids, push the  
2-stage frothing jet (Fig. 5) downwards, turning it slightly.  
Dip the 2-stage frothing jet (24) into the milk and press the  
key.  
STEAM PORTION  
The steam dispensing process stops automatically.  
A small amount of water leaks from the jet when you start  
frothing. This does not affect the result, e.g. when frothing  
milk.  
There might be some initial splashing when drawing off  
steam. The steam jet gets hot. Avoid direct contact with the  
skin!  
11.2 Frothing milk  
(with the 2-stage frothing jet)  
SELECT PRODUCT  
Pour milk into a jug or similar receptacle.  
SELECT PRODUCT  
12  
11.5 Cleaning the Professional-Cappuccino Frother  
and jet  
Dip the 2-stage frothing jet (24) into the milk and press the  
key.  
DRAW OFF STEAM  
After heating or frothing milk, you should clean the Profes-  
sional-Cappuccino Frother. We recommend cleaning it on a  
daily basis.  
When you have frothed the milk to your liking, pres the  
key  
again.  
Your IMPRESSA will not prompt you to clean the Profes-  
sional-Cappuccino Frother.  
11.3 Attaching the Professional-Cappuccino Frother  
to the IMPRESSA  
The Professional-Cappuccino Frother and the Easy-Cappuc-  
cino Frother are best cleaned using the JURA Auto-Cappuc-  
cino cleaner. Please contact an authorized dealer. We recom-  
mend cleaning these devices daily.  
Remove the 2-stage frothing jet (24).  
Now attach the Professional-Cappuccino Frother (Fig. 6).  
Press the hose into one side of the opening behind the dial  
(Fig. 7).  
Fill water into a receptacle and dip the milk hose into it.  
11.4 Making cappuccino and hot milk with the  
Professional-Cappuccino Frother  
Draw steam until the water / steam from the Frother runs clear.  
We also recommend regularly disassembling the Frother and  
rinsing it under running water.  
E
Fill the milk pitcher with milk or dip the milk hose directly into  
the milk.  
Place a cup under the Professional-Cappuccino Frother.  
Remove the Professional-Cappuccino Frother from the IMPRES-  
SA and take it apart as shown in Fig. 8.  
Press the Steam Portion key  
STEAM PORTION  
.
Thoroughly rinse all the parts of the Professional-Cappuccino  
Frother under running water.  
The machine will froth or heat milk according to the time you  
programmed (see “Programming the steam portion”, Chapter  
13.8)  
Re-assemble the Professional-Cappuccino Frother and attach it  
to your IMPRESSA.  
For cappuccino, turn the selector switch (1, Fig. 7) to (2).  
12. Switching the IMPRESSA off  
For hot milk, turn the selector switch (1, Fig. 7) to (3).  
Switching the IMPRESSA off causes the coffee spout to be rinsed  
first. Therefore, please make sure to place a suitable receptacle un-  
der the coffee spout (18).  
Now place the cup with the cappuccino froth or hot milk under  
the coffee spout (18) and make a coffee of your choice.  
SELECT PRODUCT  
Switch the IMPRESSA off with the ON / OFF key  
(11).  
13  
13.3 Maintenance  
MACHINE RINSING  
The coffee spout (18) is rinsed.  
You can activate the following maintenance functions from this  
program item:  
13. Programming  
RINSE MACHINE, CLEAN MACHINE, DE-SCALE MACHINE,  
CHANGE FILTER.  
The IMPRESSA leaves the factory with a number of default  
settings that allow you to make coffee without having to pro-  
gram the machine first. You can, however, adjust various  
parameters to make the coffee suit your personal taste.  
“DE-SCALE machine” is not displayed if you are using a CLARIS  
plus filter and the filter is set to “YES”.  
“CHANGE FILTER” is not displayed if you are not using a  
CLARIS plus filter and the filter is set to “NO”.  
The following parameters can be adjusted:  
SELECT PRODUCT  
ț Filter  
ț Water hardness  
ț Rinse  
Open the programming door (3). Press the Rotary Switch (4)  
until you hear an acoustic signal.  
ț Powder quantity  
ț Water quantity  
ț Temperature  
ț Water portion  
ț Steam portion  
ț Economy mode  
ț Time  
FILTER  
NO or YES  
Turn the Rotary Switch (4) until the following message is dis-  
played:  
RINSE  
Now press the Rotary Switch (4) to start programming.  
ț Automatic switch-on time  
ț Automatic switch-off time  
ț Language  
RINSE  
MACHINE  
Turn the Rotary Switch (4) until the required maintenance func-  
tion (for selection see above) is displayed. Press the Rotary  
Switch (4) to activate the function.  
ț Display  
ț Information (to be viewed only)  
13.1 Programming the filter  
The Maintenance menu closes automatically after 5 seconds  
if no function is selected.  
Please refer to Chapter 5 “Using the CLARIS plus filter cartridge”.  
13.4 Programming the amount of powder for coffee  
and espresso  
13.2 Programming your machine to the correct  
water hardness (only with FILTER NO)  
You can adjust the amount of powder for coffee and espresso  
separately.  
Please refer to Chapter 4 “Adjusting your machine to the water  
hardness”.  
14  
13.5 Setting the amount of water for coffee,  
espresso and coffee à la carte  
SELECT PRODUCT  
Open the programming door (3). Press the Rotary Switch (4)  
until you hear an acoustic signal.  
The system’s basic settings include pre-defined amounts of water  
(coffee 130 ml, espresso 60 ml, 2 coffees 260 ml, coffee à la carte  
145 ml). However, these can be modified as required.  
FILTER  
NO or YES  
Turn the Rotary Switch (4) until the following message is dis-  
played:  
SELECT PRODUCT  
Open the programming door (3). Press the Rotary Switch (4) un-  
til you hear an acoustic signal.  
POWDER  
QUANTITY  
FILTER  
NO or YES  
Now press the Rotary Switch (4) to start programming.  
SELECT  
Turn the Rotary Switch (4) until the following message is dis-  
PRODUCT  
played:  
Then press a product key of your choice.  
NORMAL (example)  
ⅥⅥⅥ _ _ _ +  
WATER  
QUANTITY  
Press the Rotary Switch (4) to activate the program item.  
Now turn the Rotary Switch (4) until the required amount of  
powder is set.  
E
SELECT  
PRODUCT  
STRONG (example)  
ⅥⅥⅥⅥ _ _ +  
Confirm the selected setting by pressing the Rotary Switch (4).  
Press a product key of your choice.  
1 ESPRESSO (example)  
60 ML  
POWDER  
Turn the Rotary Switch (4) to adjust the amount of water and  
QUANTITY  
then confirm your setting by pressing the Rotary Switch (4).  
Now turn the Rotary Switch (4) until the following message is  
displayed:  
WATER  
QUANTITY  
EXIT  
Turn the Rotary Switch (4) until the following message is dis-  
Now press the Rotary Switch (4) to leave the programming  
mode.  
played:  
EXIT  
Press the Rotary Switch (4) to leave the programming mode.  
SELECT PRODUCT  
SELECT PRODUCT  
15  
13.6 Programming the temperature for coffee,  
espresso and coffee à la carte  
13.7 Programming the water portion  
The system’s basic settings include a pre-defined amount of water  
(225 ml). However, this amount can be modified as required.  
You can adjust the temperature for each type of coffee  
separately. The temperature can be set to 2 different levels  
(NORMAL, HIGH).  
SELECT PRODUCT  
Open the programming door (3). Press the Rotary Switch (4)  
until you hear an acoustic signal.  
SELECT PRODUCT  
Open the programming door (3). Press the Rotary Switch (4)  
until you hear an acoustic signal.  
FILTER  
NO or YES  
FILTER  
NO or YES  
Turn the Rotary Switch (4) until the following message is dis-  
played:  
Turn the Rotary Switch (4) until the following message is dis-  
played:  
WATER  
PORTION  
TEMPERATURE  
Now press the Rotary Switch (4) to start programming.  
SELECT PRODUCT  
Then press a product key of your choice.  
Press the Rotary Switch (4) to activate the program item.  
PORTION  
225 ML (example)  
Turn the Rotary Switch (4) to adjust the amount of water and  
then confirm your setting by pressing the Rotary Switch (4).  
TEMPERATURE  
NORMAL (example)  
WATER  
PORTION  
Now turn the Rotary Switch (4) until the required temperature is  
Turn the Rotary Switch (4) until the following message is dis-  
played:  
set.  
TEMPERATURE  
HIGH (example)  
EXIT  
Press the Rotary Switch (4) to leave the programming mode.  
SELECT PRODUCT  
Confirm the selected setting by pressing the Rotary Switch (4).  
TEMPERATURE  
Now turn the Rotary Switch (4) until the following message is  
displayed:  
13.8 Programming the steam portion  
EXIT  
The system’s basic settings include a pre-defined steam portion (20  
sec.). However, this amount can be modified as required.  
Now press the Rotary Switch (4) to leave the programming  
mode.  
SELECT PRODUCT  
SELECT PRODUCT  
Open the programming door (3). Press the Rotary Switch (4)  
until you hear an acoustic signal.  
16  
Now press the Rotary Switch (4) to start programming.  
FILTER  
NO or YES  
ECONOMY  
MODE -  
Turn the Rotary Switch (4) until the following message is dis-  
played:  
Now turn the Rotary Switch (4) until the required economy  
mode is displayed.  
STEAM  
PORTION  
ECONOMY  
MODE 2 (example)  
Press the Rotary Switch (4) to activate the program item.  
Confirm the selected setting by pressing the Rotary Switch (4).  
PORTION  
20 SEC (example)  
ECONOMY  
MODE 2 (example)  
Turn the Rotary Switch (4) to modify the steam portion and then  
confirm your setting by pressing the Rotary Switch (4).  
Now turn the Rotary Switch (4) until the following message is  
displayed:  
STEAM  
PORTION  
EXIT  
Turn the Rotary Switch (4) until the following message is dis-  
played:  
Now press the Rotary Switch (4) to leave the programming  
mode.  
EXIT  
Press the Rotary Switch (4) to leave the programming mode.  
SELECT PRODUCT  
SELECT PRODUCT  
E
Economy mode –  
Selecting this level puts the IMPRESSA in constant stand-by  
mode.  
This setting allows you to make any of the products without having  
to wait for the machine to heat up.  
13.9 Economy mode  
You can set your machine to various power saving modes.  
Select this setting if you want to make a lot of coffees with  
hot or frothed milk and do not want to wait for the machine  
to heat up first.  
SELECT PRODUCT  
Open the programming door (3). Press the Rotary Switch (4)  
until you hear an acoustic signal.  
FILTER  
NO or YES  
Economy mode 1  
Selecting this level puts the IMPRESSA in constant stand-by mode  
for making coffee. The machine is heated up separately if you need  
steam for hot or frothed milk.  
Turn the Rotary Switch (4) until the following message is dis-  
played:  
ECONOMY  
MODE –  
17  
Select this setting if you make mostly black coffees and are  
prepared to wait for approx. 1 minute before being able to  
draw steam.  
TIME  
13:00 (example)  
Press the Rotary Switch (4) to confirm the hours and to activate  
the minutes.  
Economy mode 2  
TIME  
13:00  
Selecting this level does not put the IMPRESSA in stand-by mode  
(economy temperature). The machine heats up each time you make  
coffee or need to draw steam.  
The IMPRESSA switches to economy temperature 5 minutes after  
you last used it.  
Turn the Rotary Switch (4) to set the minutes.  
TIME  
13:50 (example)  
Press the Rotary Switch (4) to confirm the minutes.  
TIME  
13:50  
Select this setting if you make very few coffees (with or  
without milk) and are prepared to wait for approx. 30 sec-  
onds for the machine to get ready.  
Now turn the Rotary Switch (4) until the following message is  
displayed:  
EXIT  
13.10 Setting the time  
Now press the Rotary Switch (4) to leave the programming  
mode.  
You must program the time if you want to use the automatic  
switch-on function.  
SELECT PRODUCT  
SELECT PRODUCT  
Open the programming door (3). Press the Rotary Switch (4)  
until you hear an acoustic signal.  
13.11 Programming the automatic switch-on time  
You must program the time if you want to use the automatic  
switch-on function.  
FILTER  
NO or YES  
Turn the Rotary Switch (4) until the following message is dis-  
played:  
SELECT PRODUCT  
Open the programming door (3). Press the Rotary Switch (4)  
TIME  
—:—  
until you hear an acoustic signal.  
FILTER  
NO or YES  
Now press the Rotary Switch (4) to start programming.  
TIME  
—:—  
Turn the Rotary Switch (4) until the following message is dis-  
played:  
Turn the Rotary Switch (4) to set the hours.  
UNIT ON  
—:—  
18  
Now press the Rotary Switch (4) to start programming.  
Turn the Rotary Switch (4) until the following message is dis-  
played:  
UNIT ON  
—:—  
OFF AFTER  
5 HRS  
Turn the Rotary Switch (4) to set the hours.  
Now press the Rotary Switch (4) to start programming.  
UNIT ON  
07:00 (example)  
OFF AFTER  
5 HRS  
Press the Rotary Switch (4) to confirm the hours and to activate  
the minutes.  
Turn the Rotary Switch (4) to set the switch-off time.  
UNIT ON  
07:00  
OFF AFTER  
4 HRS (example)  
Turn the Rotary Switch (4) to set the minutes.  
Confirm the set switch-off time by pressing the Rotary Switch  
(4).  
UNIT ON  
07:15 (example)  
OFF AFTER  
4 HRS  
Press the Rotary Switch (4) to confirm the minutes.  
Now turn the Rotary Switch (4) until the following message is  
displayed:  
UNIT ON  
07:15  
E
EXIT  
Now press the Rotary Switch (4) to leave the programming mode.  
SELECT PRODUCT  
Now turn the Rotary Switch (4) until the following message is  
displayed:  
EXIT  
Now press the Rotary Switch (4) to leave the programming mode.  
13.13 Programming the language  
SELECT PRODUCT  
SELECT PRODUCT  
If the IMPRESSA is switched off with the power switch  
(27), you will need to set the time again next time you switch  
the machine on. The machine will prompt you to do so.  
Open the programming door (3). Press the Rotary Switch (4)  
until you hear an acoustic signal.  
FILTER  
NO or YES  
13.12 Programming the automatic switch-off time  
Turn the Rotary Switch (4) until the following message is dis-  
SELECT PRODUCT  
played:  
Open the programming door (3). Press the Rotary Switch (4)  
until you hear an acoustic signal.  
LANGUAGE  
ENGLISH  
FILTER  
NO or YES  
Now press the Rotary Switch (4) to start programming.  
19  
Turn the Rotary Switch (4) to change the time format.  
LANGUAGE  
ENGLISH  
DISPLAY  
AM/PM / ML  
Turn the Rotary Switch (4) to set the language.  
Confirm your selection by pressing the Rotary Switch (4).  
LANGUAGE  
ENGLISH (example)  
DISPLAY  
AM/PM / ML  
Confirm your selection by pressing the Rotary Switch (4).  
Turn the Rotary Switch (4) to change the unit of measurement.  
LANGUAGE  
ENGLISH  
DISPLAY  
AM/PM / OZ  
Now turn the Rotary Switch (4) until the following message is  
displayed:  
Confirm your selection by pressing the Rotary Switch (4).  
EXIT  
Now press the Rotary Switch (4) to leave the programming mode.  
SELECT PRODUCT  
DISPLAY  
AM/PM / OZ  
Turn the Rotary Switch (4) until the following message is dis-  
played:  
EXIT  
13.14 Programming the display  
Now press the Rotary Switch (4) to leave the programming  
This program item allows you to change the time format  
from 24 hrs. to AM/PM and the units from ml (millilitres) to  
oz (ounces).  
mode.  
SELECT PRODUCT  
SELECT PRODUCT  
13.15 Information  
Open the programming door (3). Press the Rotary Switch (4)  
This program item enables you to check the number of  
products you made and how often you selected a specific  
function.  
until you hear an acoustic signal.  
FILTER  
NO or YES  
SELECT PRODUCT  
Turn the Rotary Switch (4) until the following message is dis-  
played:  
Open the programming door (3). Press the Rotary Switch (4)  
until you hear an acoustic signal.  
DISPLAY  
24HRS / ML  
FILTER  
NO or YES  
Now press the Rotary Switch (4) to start programming.  
Turn the Rotary Switch (4) until the following message is dis-  
played:  
DISPLAY  
24HRS / ML  
INFO  
20  
The coffee à la carte button is now locked and can no longer  
be used to alter the amount of powder or water for individual  
beverages. To release the coffee à la carte button again, you  
should proceed as follows:  
Now press the Rotary Switch (4) to access the Information  
menu.  
TOTAL  
1000 (example)  
Turn the Rotary Switch (4) to display how often you made  
espresso, 2 espressos, 1 coffee, 2 coffees, coffee à la carte, pow-  
der, water and steam.  
Switch your machine off by pressing the ON/OFF button  
.
Open the programming door (3)  
Hold the Rotary Switch and the selection button for pre-ground  
coffee pressed down at the same time and wait until OK appears  
in the display.  
Finally, the number of cleaning and decalcifying cycles and filter  
changes are displayed.  
To exit the information program, press the Rotary Switch (4).  
INFO  
14.2 Locking the programming function  
Now turn the Rotary Switch (4) until the following message is  
Switch your machine off by pressing the ON/OFF button  
.
displayed:  
Open the programming door (3)  
EXIT  
Hold the Rotary Switch and the coffee à la carte draw-off button  
pressed down at the same time and wait until STOP appears in  
the display.  
Now press the Rotary Switch (4) to leave the programming  
mode.  
E
SELECT PRODUCT  
The Rotary Switch can no longer be used to gain access to  
the Programming mode. To release Programming mode  
again, you should proceed as follows:  
14. Lock functions  
If you install your IMPRESSA in a self-service area, you  
may wish to protect certain settings through a combination of  
buttons. You can therefore lock the programming function  
and disable the drawing of coffee à la carte.  
Switch your machine off by pressing the ON/OFF button  
.
Open the programming door (3)  
Hold the Rotary Switch and the coffee à la carte draw-off button  
pressed down at the same time and wait until OK appears in the  
display.  
14.1 Locking/releasing the drawing of coffee  
à la carte  
Switch your machine off by pressing the ON/OFF button  
.
15. Maintenance  
Open the programming door (3)  
15.1 Filling the water tank  
Hold the Rotary Switch and the selection button for pre-ground  
coffee pressed down at the same time and wait until STOP  
appears in the display.  
FILL  
WATER TANK  
21  
If this information is displayed, the machine will no longer  
make coffee. Refill water as described in Chapter 2.3.  
TRAY  
MISSING  
Place the empty, clean drip tray (1) and the coffee grounds bin  
back into the IMPRESSA.  
SELECT PRODUCT  
SELECT PRODUCT  
The water tank should be rinsed out and filled with fresh  
water daily. Always use fresh, cold water. Never fill the  
water tank with milk, mineral water or other liquids.  
15.4 Drip tray missing  
TRAY  
MISSING  
15.2 Emptying the coffee grounds  
EMPTY  
GROUNDS  
If this information is displayed, the machine will no longer  
make coffee. The drip tray (1) has not been installed or not  
been installed properly.  
If this information is displayed, the machine will no longer  
make coffee. However, the machine will still dispense hot  
water and steam. Empty the coffee grounds bin (26).  
Insert the drip tray (1) and the coffee grounds bin.  
SELECT PRODUCT  
Carefully take out the drip tray (1) – which contains water – and  
the coffee grounds bin (Fig. 15).  
15.5 Filling the bean tank  
TRAY  
MISSING  
FILL  
BEANS  
Place the empty, clean drip tray (1) and the coffee grounds bin  
back into the IMPRESSA. (The tray must be removed from the  
machine for at least 10 seconds).  
If this information is displayed, the machine will no longer  
make coffee. However, the machine will still dispense hot  
water and steam. Refill beans as described in Chapter 2.4.  
SELECT PRODUCT  
SELECT PRODUCT  
15.3 Emptying the drip tray  
15.6 Removing stones from the grinding gear  
EMPTY  
TRAY  
Switch the machine off using the ON / OFF key  
(11).  
Turn the power switch (27) off.  
If this information is displayed, the machine will no longer  
dispense coffee or steam, and the tray must be emptied.  
Open the lid of the bean tank (16) and remove the aroma preser-  
vation cover (15).  
Carefully take out the drip tray (1) – which contains water – and  
the coffee grounds bin (Fig. 15).  
Remove any beans with a vacuum cleaner.  
22  
Remove the screw in the bean tank (Fig. 9) and fold the finger  
protection device up (Fig. 10).  
15.9 Prompt to decalcify  
Lime scale builds up in the IMPRESSA as a result of normal use.  
The degree of calcification depends on the hardness of the water  
you use. The IMPRESSA recognizes when you should run a decal-  
cifying cycle. The machine will still make coffee, hot water and  
steam. However, we recommend that you should decalcify the ma-  
chine (see Chapter 16) within the next few days.  
Insert the key (Fig. 11).  
Now turn the key counter-clockwise until the jammed stone is  
released.  
Remove any remaining powder with a vacuum cleaner.  
Fold the finger protection device (Fig. 10) down and screw it  
tight.  
SELECT PRODUCT /  
DE-SCALE MACHINE  
Fill the bean tank with fresh beans.  
After a while the display will change. You should run the decalci-  
fying cycle now (see Chapter 16).  
15.7 Changing the filter  
After 50 litres of water the filter cartridge will need to be  
replaced. The display will prompt you to change the filter.  
SELECT PRODUCT /  
DE-SCALE NOW  
Refer to Chapter 5.2 “Changing the filter”.  
15.10 Emptying the system  
E
15.8 Prompt to run cleaning cycle  
Requirements: The IMPRESSA has been switched off with the  
After having dispensed 220 products or after 80 rinsing cycles, the  
IMPRESSA must be cleaned. You will be informed of this by a  
message on the display. The machine will still make coffee, hot  
water and steam. However, we recommend that you should run the  
cleaning cycle (see Chapter 15) within the next few days.  
ON / OFF key  
(11), but the power switch (27) is still turned on.  
This is necessary to protect the machine against damage  
occurring during transport as a result of frost.  
Place a receptacle under the pivoting steam spout (23).  
SELECT PRODUCT /  
CLEAN MACHINE  
Press one of the Steam keys  
until the following message is  
displayed:  
After another 30 products the display will change. You should run  
the cleaning cycle now (see Chapter 15).  
SYSTEM  
EMPTYING  
When the process has been completed, the IMPRESSA switches  
itself off.  
SELECT PRODUCT /  
CLEAN NOW  
The display will read “FILL SYSTEM / PRESS STEAM” next  
time you switch the machine on. For more information, please refer  
to Chapter 3 “First use”.  
23  
15.11 General cleaning instructions  
EMPTY TRAY /  
EMPTY GROUNDS  
Never use sharp objects or caustic chemicals for cleaning.  
Clean the case using a soft, damp cloth.  
Empty out the drip tray (1) and the coffee grounds bin (Fig. 15).  
TRAY  
MISSING  
Clean the pivoting steam spout (23) after each use.  
After heating milk, draw off some hot water to clean the inside  
of the pivoting steam spout (23).  
Place the empty, clean drip tray (1) and the coffee grounds bin  
back into the IMPRESSA.  
Remove the Professional-Cappuccino Frother to clean it  
thoroughly.  
PRESS  
RINSE  
The water tank should be rinsed out and filled with fresh water  
daily.  
Place a sufficiently large receptacle (ca. 0.5 litres) under the  
coffee spout (18).  
Press Rinse  
.
Visible calcification in the water tank can be removed using  
a commercial decalcifying agent. To do so, remove the water  
tank from the machine.  
MACHINE  
CLEANING  
You will hear an acoustic signal.  
If you are using a CLARIS plus filter cartridge, remove it  
from the tank first.  
ADD  
TABLET / PRESS RINSE  
Open the lid of the filler funnel for pre-ground coffee (17). Drop  
a JURA cleaning tablet inside (Fig. 12) and close the lid.  
16. Cleaning  
The IMPRESSA features an integrated cleaning program. The  
process takes approx.15 minutes.  
Press Rinse  
.
MACHINE  
CLEANING  
Please contact your authorized dealer for JURA cleaning  
tablets that are suitable specifically for the cleaning program  
of your IMPRESSA. Please note that the use of unsuitable  
cleaning agents may cause damage to your machine and  
could leave unfavourable residues in the water.  
You will hear an acoustic signal.  
EMPTY TRAY /  
EMPTY GROUNDS  
Empty out the drip tray (1) and the coffee grounds bin (Fig. 15).  
TRAY  
MISSING  
Once started, the cleaning process must not be interrupted.  
Place the empty, clean drip tray (1) and the coffee grounds bin  
back into the IMPRESSA.  
SELECT PRODUCT  
CLEAN MACHINE  
SELECT PRODUCT  
Press Rinse  
until the following message appears:  
24  
When the cleaning program has finished, take out the removable  
coffee powder tank and briefly rinse it under running water.  
Press Rinse  
until the following message appears:  
EMPTY TRAY /  
EMPTY GROUNDS  
Empty out the drip tray (1) and the coffee grounds bin (Fig. 15).  
You can also trigger a cleaning cycle manually at any point  
in time (see Chapter 13.3).  
TRAY  
MISSING  
17. Decalcifying  
Place the empty, clean drip tray (1) and the coffee grounds bin  
back into the IMPRESSA.  
The IMPRESSA features an integrated decalcifying program. The  
process takes approx.50 minutes.  
AGENT IN TANK /  
PRESS STEAM  
Lime scale builds up in the IMPRESSA as a result of normal  
use. The degree of calcification depends on the hardness of  
the water you use. The IMPRESSA recognizes when you  
should run a decalcifying cycle. The machine will still make  
coffee and hot water/steam. However, we recommend that  
you should decalcify the machine within a few days after the  
message was displayed.  
Take out the water tank (14). Empty out any remaining water.  
Completely dissolve the content of one blister (3 tablets) in a  
receptacle containing 0.6 litres of water, and pour the mixture into  
the water tank. Place the water tank back into the machine.  
Remove the 2-stage frothing jet (24) or Professional-Cappuccino  
Frother from the machine (if attached).  
E
Please contact your authorized dealer for JURA decalcifying  
tablets that are suitable specifically for the decalcifying  
program of your IMPRESSA. Please note that the use of  
unsuitable decalcifying agents may cause damage to your  
machine and could leave unfavourable residues in the water.  
Place a tall receptacle under the pivoting steam spout (23) and  
press one of the Steam keys  
.
MACHINE  
DE-SCALING  
Remove any splashes or drops of the decalcifying agent from  
sensitive surfaces, in particular surfaces made of natural  
stone or wood, or take appropriate preventive measures.  
You will hear an acoustic signal.  
OPEN TAP  
Place the receptacle under the hot water spout (25).  
Turn the Hot Water key (22) to the symbol.  
Once started, the decalcifying program must not be inter-  
rupted.  
MACHINE  
DE-SCALING  
Always wait until the decalcifying agent has been used up  
and the tank is empty. Never fill in additional decalcifying  
agent.  
You will hear an acoustic signal.  
CLOSE TAP  
Turn the Hot Water key (22) to the  
symbol.  
SELECT PRODUCT  
DE-SCALE MACHINE  
25  
You will hear an acoustic signal.  
MACHINE  
DE-SCALING  
EMPTY TRAY /  
EMPTY GROUNDS  
You will hear an acoustic signal.  
Empty out the drip tray (1) and the coffee grounds bin (Fig. 15).  
EMPTY TRAY /  
EMPTY GROUNDS  
TRAY  
MISSING  
Empty out the drip tray (1) and the coffee grounds bin (Fig. 15).  
Place the empty, clean drip tray (1) and the coffee grounds bin  
back into the IMPRESSA.  
TRAY  
MISSING  
SELECT PRODUCT  
Place the empty, clean drip tray (1) and the coffee grounds bin  
back into the IMPRESSA.  
You can also trigger a decalcifying cycle manually at any  
point in time (see Chapter 13.3).  
FILL WATER TANK /  
RINSE WATER TANK  
Thoroughly rinse out the water tank and fill it with fresh cold  
tap water. Then place it back into the IMPRESSA.  
18. Disposal  
Please return the IMPRESSA to your local dealer, the service shop  
or to JURA for proper disposal.  
PRESS STEAM  
Place a receptacle under the pivoting steam spout (23).  
Press one of the Steam keys  
19. Tips for perfect coffee  
.
Height-adjustable coffee spout (18)  
You can adjust the height of the coffee spout to the size of your  
cups.  
MACHINE  
DE-SCALING  
You will hear an acoustic signal.  
OPEN TAP  
Grinding degree  
Refer to Chapter 2.5 “Adjusting the grinding gear”.  
Place the receptacle under the hot water spout (25).  
Turn the Hot Water key (22) to the symbol.  
Preheating cups  
MACHINE  
The machine features a heatable cup shelf (19). You can, however,  
additionally preheat the cups with hot water. The smaller the quan-  
tity of coffee you make, the more important preheating is.  
DE-SCALING  
You will hear an acoustic signal.  
CLOSE TAP  
Turn the Hot Water key (22) to the  
Sugar and cream  
Stirring causes heat to be released. Adding refrigerated cream or  
milk will reduce the temperature of the coffee significantly.  
symbol.  
MACHINE  
DE-SCALING  
26  
20. Problems  
Problem  
Cause  
Remedy  
Grinding gear makes a very loud noise  
Too little froth when frothing milk  
Coffee only drips from the coffee spout  
Foreign body in the grinding gear  
Professional Cappuccino Frother clogged  
Grinding degree too fine  
Pre-ground coffee too fine  
Please refer to Chapter 14.6  
Clean frother (Chapter 11.5)  
Adjust grinding gear to coarser grind  
Use a coarser type of pre-ground coffee  
Clean metal contacts  
Display constantly indicates ‘Tray missing‘  
Soiled metal contacts at rear of drip  
tray (Fig. 13)  
‘Fill beans’ not displayed despite empty  
bean tank  
Bean monitoring system soiled  
Clean bean tank (dry)  
E
27  
21. Legal information  
22. Technical data  
Voltage:  
These operating instructions contain all the information required  
for operating and maintaining the machine properly.  
Knowledge of and compliance with the specifications contained in  
these operating instructions is required for using the machine  
safely as well as for operational safety and safety during mainte-  
nance.  
230 V AC  
1350 W  
10 A  
Power:  
Fuse:  
Safety check:  
These operating instructions cannot cover all conceivable appli-  
cations.  
Economy Mode – power consumption: 40 Wh  
Economy Mode 1 power consumption: 20 Wh  
Economy Mode 2 power consumption: 15 Wh  
Additionally, we point out that the contents of these operating  
instructions do not modify or form part of any previous or existing  
agreement, consent or legal relationship. Any obligations to be  
fulfilled by JURA Elektroapparate AG are stipulated in the corre-  
sponding purchase contract which also contains the full and solely  
applicable warranty terms. These contractual warranty terms are  
neither extended nor limited by the specifications contained in  
these operating instructions.  
The operating instructions contain information that is protected by  
Copyright. Photocopying or translations into other languages shall  
not be permissible without JURA Elektroapparate AG’s written  
approval.  
Pump pressure:  
static max. 15 bar  
Water tank:  
5.7 litres  
Bean tank capacity:  
Coffee grounds bin capacity:  
Length of cable:  
Weight:  
280 g.  
max. 40 portions  
approx. 1.1 m  
15.2 kg  
E
Dimensions (WxHxD):  
41 x 47 x 39 cm  
This appliance complies with the following EC directives:  
73/23/EEC of February 19th, 1973, “Low Voltage Directive” and  
amending directive 93/336/EEC.  
89/336/EEC of May 3rd,1989, “EMC Directive” and amending  
directive 92/31/EEC.  
28  

NAD VISO TWO User Manual
Melissa 245044 User Manual
Lindy 20983 User Manual
Kenwood CD RECEIVER KDC 7060R User Manual
Kalorik Team International Group Coffeemaker USK CM 34128 User Manual
JVC KD S21 User Manual
HP Hewlett Packard IPAQ 500 User Manual
Dell STUDIO XPSTM 8100 User Manual
Bunn CDBCF DV User Manual
Briel DOMUS ES161AMB TB User Manual