Ego Technology B013281 User Manual

140 8001 1.00  
US  
English  
Operating Manual  
CUP  
Bluetooth QD ID B013281  
2 Introduction / Foreword  
Congratulations on your new EGO!  
EGO CUP is the clever beginners' solution for using your telephone in your vehicle: easy to operate, noble and compact.  
Installing the EGO CUP in the vehicle requires no special knowledge and skills. Simply place the EGO CUP on the  
adapter, engage with this while turning clockwise and finally insert into the cupholder while turning clockwise.  
Please ensure that your telephone is compatible with the EGO CUP.  
Ask your dealer, if necessary. Our Service department would also be happy to provide you with information.  
Further information regarding compatibility with various mobile phones can be found on our homepage.  
2
3
|
3 Safety instructions  
1. Improper installation — Improper installation can cause damage to the device or vehicle! Only use EGO CUP  
in the cupholder!  
2. Risk of injury — Installing the device in inappropriate positions may cause injuries in a road accident or  
render safety devices ineffective. Only use EGO CUP in the cupholder!  
3. Risk of injury / Material damage — Do not apply any direct pressure on the connection cable!  
4. Negative impact on driving safety — Inattentiveness can lead to dangerous traffic situations! Even when  
calling in handsfree mode, it is important to always focus your attention on what is happening around you.  
When navigating in difficult situations, try to avoid carrying out a phone conversation at all!  
5. Damage to the airbag — If an incorrect installation position is chosen, the airbag can be damaged or its  
function can be impaired!  
6. Insulation damages — Lay the cables in such a way that they do not become crushed or rub against each  
other!  
7. Interference with the on-board electronics — Observe the notices from the vehicle manufacturer!  
8. Proper use — This system is intended exclusively for using mobile phones in motor vehicles!  
9. Damages due to incorrect replacement parts — Incorrect replacement or exchange parts can lead to  
malfunctions! Repairs can only be performed by our Service department!  
10. Negative impact on driving safety — For your own safety, please do not perform a pairing procedure while  
driving!  
EGO CUP  
4 Scope of supply / Packaging contents  
[1]  
[2]  
[3]  
[4]  
EGO CUP  
Adapter for use in the cupholder  
Microphone  
Connection kit for connection to  
the vehicle cigarette lighter (12 V)  
[5]  
[6]  
Quick Guide  
Safety instructions  
[1]  
[4]  
[3]  
Only the connection kit included in  
the scope of supply (Funkwerk Dabendorf,  
model: R0002037) is to be used.  
[2]  
[5]  
[6]  
Ill.: Scope of supply  
 PLEASE ENSURE the completeness of the delivery. If parts are missing, please contact our service hotline:  
858.566.2170, Mo. – Th. 7.00 a.m. 5.00 p.m., Fr. 7.00 a.m. 4.00 p.m.  
4
5
|
5 Connection/Assembly  
Connection  
Assembly  
Step 1  
Step 2  
Microphone  
connection  
Adapter  
connection  
for cigarette  
lighter  
Step 3  
The assembled system is to be inserted in the cupholder  
of the vehicle by turning in a clockwise direction.  
6 Funktion test  
The function test cannot be carried out until the system has been connected to a compatible Bluetooth® mobile phone.  
Please consult the “Putting into operation“ section further back in this instruction manual for details of the procedure.  
EGO CUP  
7 Operating instructions  
 NEGATIVE IMPACT ON DRIVING SAFETY! Inattentiveness can lead to dangerous traffic situations. Even when calling  
in handsfree mode, it is important to always focus your attention on what is happening around you. When navigating  
in difficult situations, try to avoid carrying out a phone conversation at all!  
7.1 Functions  
7.1.1 Function overview  
The EGO CUP handsfree system supports the Bluetooth® handsfree profile. This means that the system can be used  
to operate telephones which support this profile. EGO CUP is the clever beginners solution for using your telephone  
in your vehicle and offers the following range of functions:  
Æ Call functions such as accept call, reject call and redial  
Æ Support of the mobile phone voice dialling  
Æ Registration of up to 8 mobile phones  
7.2 Symbols  
Accept call,  
redial  
Increase  
volume  
The control unit of the EGO CUP has a total of  
4 buttons. The picture to the right gives a brief  
overview of the available buttons.  
The functions of the individual buttons are  
explained next to the picture.  
Lower  
volume  
End call, reject  
call, begin the  
voice dialling of  
the mobile phone  
6
7
|
LED – functions  
An LED is integrated in the EGO CUP. This is used to display various states. The following states may occur.  
LED – state with inactive Bluetooth®- connection  
- LED flashes in intervals shortly  
Æ No mobile phone connected  
LED – state with active Bluetooth®- connection  
- LED permanently on  
- LED quickly flashes in intervals  
- LED off  
Æ Mobile phone connected, network reception exists  
Æ Active call  
Æ No network reception  
7.3  
Putting into operation  
Take the time to familiarise yourself with the operation of the system together with the telephone. Make some initial  
calls during which you determine the ideal conditions for the volume and the speaking direction before you use the  
system while driving. When putting into operation, the vehicle should be parked in a quite place. Making arrangements  
with a contact who can take the time to help you with the test connection is a decided advantage.  
7.3.1 About the Bluetooth® technology  
Bluetooth® technology is a radio technology and thus enables communication without cables. Data and speech can be  
transmitted at the same time. To do so, the devices involved do not have to be within sight of each other. The radio range  
in the open is generally 10 m, however interferences through other electrical devices or obstacles can lead to a lower  
range. The frequency band in which Bluetooth® functions is approved on a virtually global scale. This coupled with the  
fact that every Bluetooth® product is tested and qualified for problem-free cooperation with other Bluetooth® devices  
ensures the highest possible compatibility of devices from different manufacturers. The EGO CUP supports the  
Bluetooth® handsfree profile. This means that you can use this to operate telephones which support the Bluetooth®  
handsfree profile. If necessary, please refer to the operating manual that came with your mobile phone for details of  
which profile it supports.  
EGO CUP  
7.3.2 Switching on/off  
When the ignition is switched on or the connection kit is plugged in, the handsfree system switches on and the LED slowly  
flashes four times. Then the EGO CUP is in standby mode and ready to establish a connection. A compatible Bluetooth®  
telephone must be connected to the EGO CUP in order to be able to telephone with the system. You will learn how to do  
this in the following sections. If the system does not switch on after the connection kit is plugged in, activate the ignition  
of your vehicle. If the ignition is switched off or the connection cable disconnected, the handsfree system switches off. If  
the cigarette lighter of your vehicle does not switch off when the ignition key is removed, remove the connection kit from  
the cigarette lighter to switch off the system.  
7.3.3 Pairing  
A mobile phone that is to be operated using the handsfree system must be paired with EGO CUP. As long as no device is  
connected, the system is visible to all Bluetooth® devices. In this condition, the LED flashes every few seconds. The  
telephone to be used must be registered in the EGO CUP. The Bluetooth® search and pairing occurs in the mobile phone.  
The Bluetooth® identifier is „EGO CUP“. The PIN to be entered is „0000“. If the connection/pairing was successful, the  
LED lights up permanently. One telephone can be paired per user. If you wish to pair another telephone, please  
disconnect the current connection on the telephone. Should problems arise when pairing, please refer to the „Trouble-  
shooting“ section and research the device search using Bluetooth® in the operating instructions of your mobile phone.  
7.3.4 Automatic connection  
If a telephone is already connected to the system, the EGO CUP attempts to pair with this telephone. If the connection was  
successful, the LED lights up permanently. The telephone that was connected last is always paired. If this telephone is  
outside of the range, the other paired telephones are sought. If the search was successful, the system automatically  
connects to this telephone. However, if the search is unsuccessful, the system switches to pairing mode. Manual  
connection via the telephone is now possible.  
8
9
|
7.4  
Calls  
7.4.1 Incoming call  
The ringtone can be heard for an incoming call. In addition, the LED flashes periodically.  
The call can be accepted using the  
button. The call is rejected using the  
button.  
7.4.2 Outgoing call  
There are multiple options for beginning a call. The telephone's redial is activated using the  
number last dialled is dialled again. If the call is established, the LED flashes periodically. If the  
button, in which the  
button is  
pressed, the voice dialling of the telephone is initiated. Now you can say the number, the name or other commands that  
are supported by the telephone. Here the LED also flashes periodically when the call is established.  
The third possibility is direct dialling using the mobile phone.  
 IMPORTANT NOTE: Please observe the legal regulations of your country regarding use of the telephone in a vehicle!  
7.5  
Volume  
The volume can be changed using the  
and  
buttons. Pressing the  
button increases the volume and  
pressing the button lowers the volume.  
EGO CUP  
Troubleshooting:  
Problem  
Cause  
Remedy  
Mini - USB not connected  
Connection kit not connected  
Ignition not switched on  
Connect mini - USB  
Connect connection kit  
Switch on ignition  
EGO CUP does not  
switch on  
The person on the other end of the  
line cannot hear you  
Microphone not connected  
Microphone in airstream  
Connect microphone  
Decrease ventilation  
The person on the other end  
complains of noise interference  
Telephone very close to EGO CUP  
parts or car radio  
Increase the distance between the phone and  
the EGO CUP or radio  
The person on the other end  
complains of echo effects  
Volume too high  
Lower volume  
Cancel existing connection  
Lower volume  
When pairing the device, the mobile phone  
cannot be paired with the EGO CUP  
EGO CUP is already connected to a device  
Poor Bluetooth®-connection  
Audio sounds unpurified, scratchy  
The telephone is out of range  
Bring the telephone in range of the EGO CUP  
The Bluetooth®-interface is deactivated  
In the phone  
Switch Bluetooth® to “ON” in your telephone  
(”Automatic” option is insufficient)  
After switching on the ignition,  
the connection to the paired  
telephone is not established  
The telephone requires a confirmation  
that the connection was established  
Confirm the connection on the phone. Deactivate the security  
request (see operating instructions of telephone)  
One of the two devices no long has  
a valid passkey  
Perform a new pairing  
10 11  
|
8 Technical specifications  
EGO CUP dimensions  
Length of adapter cable  
Operating voltage  
76 mm x 74 mm x 43,5 mm  
0,6 m  
12 V  
Temperature range  
-10 °C to +55 °C  
Supported Bluetooth® profiles  
Handsfree  
9 Certification  
0681  
In accordance with R&TTE Directive 1999/5/EC  
03 5156  
Model certification according to EU Directive 72/245/EEC (2006/28/EC) „Radio interference (electromagnetic  
compatibility) of vehicles“  
Bluetooth® is a registered trademark of Bluetooth SIG, Inc.  
EGO CUP  
10 Conformity statement  
This device works with Bluetooth® radio technology. In certain countries the use of this device may not be allowed or  
may be restricted. Please familiarise yourself with these restrictions and do not use the device if you are unsure  
whether usage is allowed in a certain country.  
Bluetooth® is trademark of Bluetooth SIG, Inc.  
The  
Funkwerk Dabendorf GmbH  
Märkische Straße  
D-15806 Dabendorf  
confirms that the  
„EGO CUP“ handsfree system  
is in compliance with the fundamental requirements and the other relevant  
guidelines of the EU Directive 1999/5/EC.  
0681  
12 13  
|
FCC statement  
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device  
may not cause harmful interference, and (2) this device must accept any interference received, including interference  
that may cause undesired operation.  
 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part  
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference  
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to  
try to correct the interference by one or more of the following measures:  
Æ Reorient or relocate the receiving antenna.  
Æ Increase the separation between the equipment and receiver.  
Æ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Æ Consult the dealer or an experienced radio/TV technician for help.  
 WARNING: Changes or modifications made to this equipment not expressly approved by FWD may void the FCC  
authorization to operate this equipment.  
FCC Radiation Exposure statement:  
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must  
follow the specific operating instructions for satisfying RF exposure compliance.  
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.  
EGO CUP  
11 Hotline  
Do you have questions or suggestions? Would you like more information? Do you require on-site consulting and  
service? Give us a call!  
Our hotline is available to you at the following times:  
Monday – Friday  
from 8.00 AM to 5.00 PM  
Please follow the steps below:  
Æ Check whether you can solve the problem using the "Troubleshooting" section.  
Æ Please have the model of the handsfree system at hand.  
Æ Try to describe the problem as accurately as possible.  
You can reach our hotline at the following numbers:  
From Germany:  
Telephone:  
Telephone:  
Fax:  
0800 - 0 393 393  
Outside Germany:  
+49 (0) 3377 - 316 233  
+49 (0) 3377 - 316 234  
+49 (0) 3377 - 316 244  
USA  
Telephone:  
eMail:  
(+1) 858.566.2170  
14 15  
|
Raytel Corporation  
A partner of Funkwerk Dabendorf GmbH  
8820 Kenamar Drive, Ste 506  
San Diego, CA 92121  
Telephone  
Fax  
858.566.2159  
858.566.2179  
eMail  
A Funkwerk AG company.  
Internet  
Funkwerk Dabendorf reserves the right to modifications in the course of technological progress and deviations from the delivery scope! All rights  
reserved! Reproduction, in whole or in part, is only permitted with the prior written consent of Funkwerk Dabendorf GmbH!  

Mr Coffee NL5 Black User Manual
Motorola V276 User Manual
Motorola MOTOKRZR K1 User Manual
Motorola 9520 User Manual
Miglia Technology VideoExpress Converter User Manual
Kenwood Z919 User Manual
Kenwood DP M5520 User Manual
HP Hewlett Packard Hewlett Packard Computer Accessories 11689A User Manual
Agilent Technologies Clock Radio 83446A User Manual
ACTiSYS Computer Accessories ACT IR2000UL User Manual