Dell™ PowerEdge™ 2500 Systems Installation and Troubleshooting Guide
Notes, Notices, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
CAUTION: A CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
WARNING: A WARNING indicates a potentially hazardous situation which, if not avoided, may result in severe injury.
Information in this document is subject to change without notice.
© 2000 Dell Computer Corporation. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, PowerEdge, Dell OpenManage, and DellWare are trademarks of Dell Computer Corporation; Intel is a registered trademark of Intel Corporation; Microsoft, MS-DOS, Windows NT, and Windows
are registered trademarks of Microsoft Corporation; Novell and NetWare are registered trademarks of Novell, Inc.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its
own.
Initial release: January 2001
Table A-1. System-Board Jumper Settings
Jumper
Setting
Description
PASSWD
(default) The password feature is enabled.
The password feature is disabled.
NVRAM_CLR
(default) The configuration settings are retained at system boot.
The configuration settings are cleared at next system boot. (If the configuration settings become corrupted to the point where
the system will not boot, install the jumper plug and boot the system. Remove the jumper before restoring the configuration
information.)
ONCE
Reserved (do not change).
jumpered
unjumpered
NOTE: For the full name of an abbreviation or acronym used in this table, see "Abbreviations and Acronyms."
System Board Connectors
SCSI Backplane Board Connectors
Figure A-3. Connectors on the SCSI Backplane Board
Interposer Board Connectors
Figure A-4. Connectors on the Interposer Board
Disabling a Forgotten Password
The computer's software security features include a system password and a setup password, which are discussed in detail in Section 4, "Using the System Setup
Program," in the User's Guide. A password jumper on the system board enables these password features or disables them and clears any password(s) currently in
use.
To disable a forgotten system password or setup password, perform the following steps.
CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions at the front of this guide.
2. Remove the system cover.
3. Refer to Figure A-2 for the location of the password jumper (labeled "PASSWD") on the system board.
4. Remove the jumper plug from the PASSWD jumper.
5. Replace the right-side computer cover, and then reconnect the computer to an electrical outlet and turn it on.
The existing passwords are not disabled (erased) until the system boots with the PASSWD jumper plug removed. However, before you assign a new system
and/or setup password, you must install the jumper plug.
NOTE: If you assign a new system and/or setup password with the jumper plug still removed, the system disables the new password(s) the next time it
boots.
6. Repeat step 1.
7. Install the jumper plug on the PASSWD jumper.
8. Replace the right-side computer cover, and then reconnect the computer and peripherals to their electrical outlets and turn them on.
9. Assign a new system and/or setup password.
To assign a new system password using the System Setup program, see "Assigning a System Password" in the User's Guide.
Abbreviations and Acronyms
Dell™ PowerEdge™ 2500 Systems Installation and Troubleshooting Guide
The following list defines or identifies technical terms, abbreviations, and acronyms used in Dell user documents.
NOTE: Unless otherwise specified, these definitions may not apply to operating systems other than Microsoft® Windows® 95 and Windows NT®.
A
ampere(s)
AC
alternating current
ACPI
Advanced Configuration and Power Interface
ADC
analog-to-digital converter
ADI
Autodesk Device Interface
AI
artificial intelligence
ANSI
American National Standards Institute
APIC
Advanced Peripheral Interrupt Controller
ASCII
American Standard Code for Information Interchange
ASIC
application-specific integrated circuit
B
BASIC
Beginner's All-Purpose Symbolic Instruction Code
BBS
bulletin board service
BIOS
basic input/output system
bpi
bits per inch
bps
bits per second
BTU
British thermal unit
C
Celsius
CCFT
cold cathode fluorescent tube
CD
compact disc
CD-ROM
compact disc read-only memory
CGA
color graphics adapter
cm
centimeter(s)
CMOS
complementary metal-oxide semiconductor
C.O.D.
collect on delivery
cpi
characters per inch
cpl
characters per line
CPU
central processing unit
DAC
digital-to-analog converter
DASH
Dell Advanced SCSI Host
DAT
digital audio tape
dB
decibel(s)
dBA
adjusted decibel(s)
DC
direct current
DIMM
dual in-line memory module
DIN
Deutsche Industrie Norm
DIP
dual in-line package
DMA
direct memory access
DOC
Department of Communications (in Canada)
dpi
dots per inch
DRAC
Dell OpenManage™ Remote Assistant Card
DRAM
dynamic random-access memory
DS/DD
double-sided double-density
DS/HD
double-sided high-density
DSA
Dell SCSI Array
ECC
error checking and correction
EDO
extended-data out
EGA
enhanced graphics adapter
EIDE
enhanced integrated drive electronics
EMI
electromagnetic interference
EMM
expanded memory manager
EMS
Expanded Memory Specification
EPP
Enhanced Parallel Port
EPROM
erasable programmable read-only memory
ESD
electrostatic discharge
ESDI
enhanced small-device interface
ESM
embedded server management
F
Fahrenheit
FAT
file allocation table
FCC
Federal Communications Commission
FIFO
first-in first-out
ft
feet
g
gram(s)
G
gravities
GB
gigabyte(s)
GUI
graphical user interface
h
hexadecimal
HIP
Hardware Instrumentation Package
HMA
high memory area
HPFS
High Performance File System
Hz
hertz
I/O
input/output
ICBM
inter-chassis management bus
ID
identification
IDE
integrated drive electronics
IRQ
interrupt request
ISA
Industry-Standard Architecture
JEIDA
Japanese Electronic Industry Development Association
K
kilo- (1024)
KB
kilobyte(s)
KB/sec
kilobyte(s) per second
Kb
kilobit(s)
Kbps
kilobit(s) per second
kg
kilogram(s)
kHz
kilohertz
LAN
local area network
lb
pound(s)
LCD
liquid crystal display
LED
light-emitting diode
LIF
low insertion force
LN
load number
lpi
lines per inch
LVD
low voltage differential
m
meter(s)
mA
milliampere(s)
mAh
milliampere-hour(s)
MB
megabyte(s)
Mb
megabit(s)
Mbps
megabit(s) per second
MBR
master boot record
MDA
monochrome display adapter
MGA
monochrome graphics adapter
MHz
megahertz
MMX™
MultiMedia eXtensions
mm
millimeter(s)
ms
millisecond(s)
MS-DOS®
Microsoft Disk Operating System
MTBF
mean time between failures
mV
millivolt(s)
NIC
network interface controller
NiCad
nickel cadmium
NiMH
nickel-metal hydride
NMI
nonmaskable interrupt
NNM
Network Node Manager
ns
nanosecond(s)
NTFS
NT File System
NVRAM
nonvolatile random-access memory
OS/2®
Operating System/2
OTP
one-time programmable
PAL
programmable array logic
PCI
Peripheral Component Interconnect
PCMCIA
Personal Computer Memory Card International Association
PGA
pin grid array
POST
power-on self-test
ppm
pages per minute
PQFP
plastic quad flat pack
PSDB
power-supply distribution board
PS/2
Personal System/2
PVC
polyvinyl chloride
QIC
quarter-inch cartridge
RAID
redundant arrays of independent disks
RAM
random-access memory
RAMDAC
random-access memory digital-to-analog converter
RCU
Resource Configuration Utility
REN
ringer equivalence number
RFI
radio frequency interference
RGB
red/green/blue
ROM
read-only memory
rpm
revolutions per minute
RTC
real-time clock
SCA
Single Controller Architecture
SCSI
small computer system interface
SDS
Scalable Disk System
sec
second(s)
SEC
single-edge contact
SDRAM
synchronous dynamic random-access memory
SIMM
single in-line memory module
SMB
server management bus
SNMP
Simple Network Management Protocol
SRAM
static random-access memory
SSU
system setup utility
SVGA
super video graphics array
TFT
thin film transistor
tpi
tracks per inch
TSR
terminate-and-stay-resident
UMB
upper memory block
UPS
uninterruptible power supply
USOC
Universal Service Ordering Code
V
volt(s)
VAC
volt(s) alternating current
VDC
volt(s) direct current
VESA®
Video Electronics Standards Association
VGA
video graphics array
VLSI
very-large-scale integration
VRAM
video random-access memory
VRM
voltage regulator module
W
watt(s)
WH
watt-hour(s)
X
XMM
extended memory manager
XMS
eXtended Memory Specification
Z
ZIF
zero insertion force
Introduction
Dell™ PowerEdge™ 2500 Systems Installation and Troubleshooting Guide
Dell™ PowerEdge™ 2500 systems are high-speed servers that offer significant service and upgrade features. These systems include the following service features to
make troubleshooting and repair easy and effective:
l
Embedded server management hardware, which monitors temperatures and voltages throughout the system and notifies you if the system overheats, if a system
cooling fan malfunctions, or a power supply fails
l
l
Redundant, hot-pluggable cooling fans and power supplies
Dell Diagnostics, which checks for hardware problems (if the system can boot)
The following system upgrade options are offered:
l
l
l
l
Additional microprocessors
Additional memory
A variety of PCI expansion-card options (including RAID controller host adapter cards)
A DRAC 2 PCI expansion-card for system management
Other Documents You May Need
Besides this Installation and Troubleshooting Guide, the following documentation is included with your system:
l
The Dell PowerEdge 2500 Systems User's Guide, which describes system features and technical specifications, video and SCSI device drivers, the system
setup program, and software support utilities.
l
The Dell OpenManage™ Server Agent documentation, which describes the features, requirements, installation, and basic operation of the server management
software. Refer to the software's online help for information about the alert messages issued by the software.
You may also have one or more of the following documents.
NOTE: Documentation updates are sometimes included with the system to describe changes to the system or software. Always read these updates before
consulting any other documentation because the updates often contain information that supersedes the information in the other documents.
l
l
l
Operating system documentation is included with the system if you ordered the operating system software from Dell. This documentation describes how to install
(if necessary), configure, and use the operating system software.
Documentation is included with any options you purchase separately from the system. This documentation includes information that you need to configure and
install these options in your Dell system.
Technical information files—sometimes called "readme" files—may be installed on the hard-disk drive to provide last-minute updates about technical changes to
the system or advanced technical reference material intended for experienced users or technicians.
Getting Help
If at any time you do not understand procedure described in this guide, or if your system does not perform as expected, Dell provides a number of tools to help you.
Safety, Regulatory, and Warranty Information
For important safety, regulatory, and warranty information, see the System Information document that came with your system.
Indicators, Messages, and Codes
Dell™ PowerEdge™ 2500 Systems Installation and Troubleshooting Guide
Applications, operating systems, and the system itself are capable of identifying problems and alerting you to them. When a problem occurs, a message may appear on
the monitor screen or a beep code may sound.
Several different types of messages can indicate when the system is not functioning properly:
l
l
l
l
l
l
System messages
System beep codes
Warning messages
Diagnostics messages
Alert messages
SCSI hard-disk drive indicator codes
The system indicators and the front and back panel features are illustrated in Figures 2-1 through 2-5. This section also describes each type of message and lists the
possible causes and actions you can take to resolve any problems indicated by a message. To determine what type of message you have received, read the following
sections.
Bezel Indicators
When the bezel is in place on the system, it has two indicators (see Figure 2-1). The hard-disk drive activity indicator and the ESM indicator. The ESM indicator
flashes amber when the system needs attention. The ESM indicator indicates a power problem, a fan/temperature problem, a hard drive problem, or that the PCI
expansion cards need attention.
Figure 2-1. Bezel Indicators
Front-Panel Indicators and Features
Two indicators are located on the front-panel: the hard-disk drive indicator and the ESM indicator. The ESM indicator flashes amber when the system needs attention.
The amber ESM indicator indicates a power problem, a system fan or power supply fan problem, temperature problem, a hard-disk drive problem, or that the PCI
expansion cards need attention. The power supplies and hard-disk drives also have indicators which can be seen when the bezel is removed. The CD-ROM and
diskette drives have green activity indicators.
Figure 2-2. Front-Panel Features
Back-Panel Features
Figure 2-3. Back-Panel Features
SCSI Hard-Disk Drive Indicator Codes
If you have the integrated RAID controller activated, or an optional PERC 3/Di controller is installed in the system, three indicators on each of the hard-disk drive
carriers provide information on the status of the SCSI hard-disk drives (see Table 2-1). The SCSI backplane firmware controls the drive online and drive failure
indicators.
Figure 2-4. Hard-Disk Drive Indicators
Table 2-1 lists the drive indicator patterns established by the SCSI backplane firmware. Different patterns are displayed as drive events occur in the system. For
example, in the event of a hard-disk drive failure, the "drive failed" pattern appears. After the drive is selected for removal, the "drive being prepared for removal"
pattern appears, followed by the "drive ready for insertion or removal" pattern. After the replacement drive is installed, the "drive being prepared for operation" pattern
appears, followed by the "drive online" pattern.
NOTE: If you do not have the integrated PERC3/Di, or an optional PERC3/DC or PERC3/QC controller installed, you will see only the "drive online" and
"drive bay empty" indicator patterns.
Table 2-1. SCSI Hard-Disk Drive Indicator Patterns
Condition
Indicator Code
Identify drive
All three drive status indicators blink simultaneously.
The three drive status indicators flash sequentially.
Drive being prepared for removal
Drive ready for insertion or removal All three drive status indicators are off.
Drive being prepared for operation The drive online indicator is on. The drive activity light may flash briefly.
Drive bay empty
Drive predicted failure
Drive failed
All three drive status indicators are off.
The drive online indicator is on. The drive failure indicator blinks on briefly each second.
The drive online indicator turns off. The drive failure indicator blinks off briefly each second.
The drive online indicator blinks rapidly.
Drive rebuilding
Drive online
The drive online indicator is on.
Redundant Power Supply Features
Each power supply has three indicators which indicate the power-on status, fault, and if there is AC power present. These power supplies are hot-pluggable.
Figure 2-5. Power Supply Features
Table 2-2. Power Supply Indicator Patterns
Indicator Indicator Code
Power-on Green indicator indicates that the power supply is operational.
Fault
Red indicator indicates a problem with the power supply i.e., fan failure, voltage error, etc.
AC present Green indicator indicates that AC power is present at the power supply and that the system is connected to an AC source.
System Messages
System messages alert you to a possible operating system problem or to a conflict between the software and hardware. Table 2-3 lists the system error messages that
can occur and the probable cause for each message.
NOTE: If you receive a system message that is not listed in Table 2-3, check the documentation for the application that is running when the message appears
and/or the operating system documentation for an explanation of the message and recommended action.
Table 2-3. System Messages
Message
Cause
Corrective Action
Address mark not found
or hard-disk drive subsystem
obtaining technical assistance.
(defective system board)
Alert! Maximum memory size
exceeded. Limiting memory size
to 4 GB
System supports up to 4 GB of
memory
Remove a memory module pair so that the maximum amount of
"Installing System Board Options."
Alert! Single-bit memory error
previously detected in xxxx
xxxxh
Improperly seated or faulty memory
modules
Remove and reseat the memory modules. See "Removing Memory
Modules" in "Installing System Board Options." If the problem
persists, replace the memory modules. See "Removing Memory
Modules" in "Installing System Board Options." If the problem still
assistance.
Alert! Previous processor
thermal failure.
The microprocessor exceeded its
recommended operating temperature Replacing a Microprocessor" in "Installing System Board Options."
during the previous operating session.
Remove and Replace the defective microprocessor. See "Adding or
Alert! Primary processor is out
of rev.
System detected that the primary
processor is not the correct revision.
Replace the microprocessor. See "Adding or Replacing a
Microprocessor" in "Installing System Board Options."
Alert! Processor thermal probe
failure detected.
Faulty processor or defective system Replace the defective microprocessor. See "Adding or Replacing a
board.
Microprocessor" in "Installing System Board Options." If the
instructions on obtaining technical assistance.
Alert! Secondary processor is
out of rev.
System detected that the secondary
processor is not the correct revision.
Replace the microprocessor with a type supported by Dell. See
Board Options."
Alert! Unsupported memory in
DIMM slot(s)
Unsupported memory module(s)
installed in specified slot(s)
Replace one or more memory modules so that the memory module
"Installing System Board Options."
Alert! Uncorrectable memory
error previously detected in
xxxx xxxxh
Improperly seated or faulty memory
modules
Remove and reseat the memory modules. See "Adding or Replacing
a Microprocessor" in "Installing System Board Options." If the
problem persists, replace the memory modules. See "Adding or
Replacing a Microprocessor" in "Installing System Board Options."
obtaining technical assistance.
Attachment failed to respond
Auxiliary device failure
Diskette drive or hard-disk drive
controller cannot send data to
associated drive
Replace the defective drive. See "Installing a Device That Uses the
System's Integrated SCSI Controller" in "Installing Drives." If the
obtaining technical assistance.
Mouse cable connector loose or
improperly connected, defective
mouse
"Troubleshooting Your System." If the problem persists, replace the
assistance.
Bad command or file name
Command entered does not exist, is
faulty, or is not in pathname specified.
Faulty command and syntax, or incorrect filename.
Bad error-correction code(ECC)
on disk read
or hard-disk drive subsystem
(defective system board)
obtaining technical assistance.
Controller has failed
Boot: Couldn't find NTLDR
A nonbootable diskette formatted with A nonbootable diskette is preventing the system from booting.
Win-dows NT was detected in the
diskette drive.
Remove the diskette to boot the system from the hard-disk drive or
from a bootable diskette.
CAUTION! NVRAM_CLR jumper is
installed on system board.
Please run SETUP.
The NVRAM_CLR jumper is
installed.
location. Run the System Setup program to correct the diskette
drive type. See
"Using the System Setup Program," in the User's Guide for
instructions.
CD-ROM drive not found
Improperly connected or missing CD- Check that the diskette drive/CD-ROM drive unit is seated
ROM drive.
properly against the interposer board on the peripheral cage. See
drive. Replace the drive. See "Installing a Device That Uses the
System's Integrated SCSI Controller" in "Installing Drives." If the
obtaining technical assistance.
CPUs with different level
cache sizes detected
2
Two different types of
microprocessors are installed
Install a correct version of the microprocessor so both micro-
processors have the same level 2 cache size. See "Adding or
Replacing a Microprocessor" in "Installing System Board Options."
Data error
Faulty diskette, diskette drive, or
hard-disk drive
Replace the diskette, diskette drive, or hard-disk drive. See
Decreasing available memory
One or more memory modules
improperly seated or faulty
Remove and reseat the memory modules. See "Removing Memory
Modules" in "Installing System Board Options." If the problem
persists, replace the memory modules. See "Removing Memory
Modules" in "Installing System Board Options." If the problem still
assistance.
Diskette drive 0 seek failure
Diskette drive 1 seek failure
Faulty or improperly inserted diskette, Replace the diskette. Run the System Setup program to correct the
incorrect configuration settings in
System Setup program, loose
diskette/CD-ROM interface cable
diskette drive type. See "Using the System Setup Program," in the
User's Guide for instructions. Check that the diskette drive/CD-
ROM drive unit is seated properly against the interposer board on
Diskette read failure
Faulty diskette, faulty or improperly
connected diskette/CD-ROM
Check that the diskette drive/CD-ROM drive unit is seated
properly against the interposer board on the peripheral cage. See
Diskette subsystem reset failed
Diskette write protected
Drive not ready
Faulty diskette/CD-ROM controller
(defective system board)
obtaining technical assistance.
Diskette write-protect feature
activated
Move the write-protect tab on the diskette.
Diskette missing from or improperly
inserted in diskette drive
Reinsert or replace the diskette.
Embedded server management error
Embedded server management
Shut down the system to clear the memory, and then restart the
memory may be temporarily corrupted system. If the problem persists, see "Getting Help," for instructions
on obtaining technical assistance.
Embedded server management is
not present
Gate A20 failure
Faulty keyboard controller (defective Replace the system board. See "Getting Help," for instructions on
system board)
obtaining technical assistance.
General failure
Operating system corrupted or not
installed properly
Reinstall the operating system.
Hard disk controller failure
Hard disk drive read failure
Hard disk failure
Incorrect configuration settings in
System Setup program, improperly
connected hard-disk drive, faulty
hard-disk drive controller subsystem
(defective system board), or loose
power cable
Check the hard-disk drive configuration settings in the System
Setup program. See "Using the System Setup Program," in the
User's Guide for instructions. Reinstall the hard-disk drive. See
Invalid configuration
information - please run SETUP
program
Incorrect configuration settings in
System Setup program, or faulty
battery
Check the System Setup configuration settings. See "Using the
System Setup Program," in the User's Guide for instructions.
"Installing System Board Options."
Invalid CPU speed detected
Microprocessor not supported by
system
Install a correct version of the microprocessor in the specified
microprocessor connector. See "Adding or Replacing a
Microprocessor" in "Installing System Board Options."
Invalid NVRAM configuration,
resource reallocated
System detected and corrected a
resource conflict when system
resources were allocated using the
System Setup program.
No action is required.
I/O parity interrupt at address
Expansion card improperly installed or Reinstall the expansion cards. See "Installing an Expansion Card" in
faulty
"Installing System Board Options." If the problem persists, replace
"Installing System Board Options."
Keyboard failure
Keyboard cable connector loose or
improperly connected, defective
keyboard, or defective
keyboard/mouse controller (defective
system board)
Check the keyboard cable connection. Replace the keyboard. If the
instructions on obtaining technical assistance.
Keyboard data line failure
Keyboard stuck key failure
Keyboard clock line failure
Keyboard controller failure
Defective keyboard/mouse controller Replace the system board. See "Getting Help," for instructions on
(defective system board)
obtaining technical assistance.
Memory address line failure at
address, read value expecting
value
Faulty or improperly seated memory
modules or defective system board
Remove and reseat the memory modules. See "Installing Memory
Modules" in "Installing System Board Options." If the problem
persists, replace the memory modules. See "Installing Memory
Modules" in "Installing System Board Options." If the problem still
assistance.
Memory data line failure at
address, read value expecting
value
Memory double word logic failure
at address, read value expecting
value
Memory odd/even logic failure at
address, read value expecting
value
Memory write/read failure at
address, read value expecting
value
Memory allocation error
Faulty application
Restart the application.
Memory parity interrupt at
address
Improperly seated or faulty memory
modules
Remove and reseat the memory modules. See "Installing Memory
Modules" in "Installing System Board Options." If the problem
persists, replace the memory modules. See "Installing Memory
Modules" in "Installing System Board Options." If the problem still
assistance.
Memory tests terminated by
keystroke
POST memory test terminated by
pressing the spacebar
No action is required.
No boot device available
Faulty diskette, diskette/CD-ROM
subsystem, hard-disk drive, hard-disk the problem persists, replace the system board. See "Getting Help,"
drive subsystem, or no boot disk in
drive A
for instructions on obtaining technical assistance.
No boot sector on hard-disk
drive
Incorrect configuration settings in
System Setup program, or no
operating system on hard-disk drive
Check the hard-disk drive configuration settings in the System
Setup program. See "Using the System Setup Program," in the
User's Guide for instructions.
No timer tick interrupt
Defective system board
obtaining technical assistance.
Non-system disk or disk error
Faulty diskette, diskette/CD-ROM
subsystem, or hard-disk drive
subsystem
for instructions on obtaining technical assistance.
Not a boot diskette
No operating system on diskette
Use a bootable diskette.
Processor in socket 1 not
installed!
No microprocessor installed in primary Install a VRM or a microprocessor in the primary microprocessor
microprocessor socket
Board Options."
Read fault
Faulty diskette, diskette/CD-ROM
subsystem, or hard-disk drive
subsystem (defective system board)
for instructions on obtaining technical assistance.
Requested sector not found
Reset failed
Improperly connected diskette/CD-
ROM, hard-disk drive, or power
cable
Check that the diskette drive/CD-ROM drive unit is seated
properly against the interposer board on the peripheral cage. See
cable and power cable connections to the backplane board. See
ROM bad checksum = address
Expansion card improperly installed or Reinstall the expansion cards. See "Installing an Expansion Card" in
faulty
"Installing System Board Options." If the problem persists, replace
"Installing System Board Options." If the problem still persists,
obtaining technical assistance.
Sector not found
Seek error
Defective sectors on diskette or hard- Replace the diskette or hard-disk drive. See "Installing Drives."
disk drive
Defective sectors on diskette or hard- Replace the diskette or hard-disk drive. See "Installing Drives."
disk drive
Seek operation failed
Shutdown failure
Faulty diskette or hard-disk drive
Defective system board
obtaining technical assistance.
System halted
System microprocessor is not a type
supported by Dell.
Replace the microprocessor with a type supported by Dell. See
Board Options."
System backplane cable error
System backplane error
Time-of-day clock stopped
Improperly attached interface cables
Check the primary and secondary SCSI interface cable connections
"Troubleshooting Your System."
Improperly attached or missing
backplane
Check the interface cable connections to the backplane board. See
System."
Defective battery or faulty chip
(defective system board)
"Installing System Board Options." If the problem persists, replace
technical assistance.
Time-of-day not set - please run
SETUP program
Incorrect Time or Date settings or
defective system battery
Check the Time and Date settings. See "Using the System Setup
Program," in the User's Guide for instructions. If the problem
persists, replace the system battery. See "Replacing the System
Battery" in "Installing System Board Options." If the problem still
instructions on obtaining technical assistance.
Timer chip counter 2 failed
Defective system board
obtaining technical assistance.
Unexpected interrupt in
protected mode
Improperly seated memory modules or Remove and reseat the memory modules. See "Installing Memory
faulty keyboard/mouse controller chip Modules" in "Installing System Board Options." If the problem
(defective system board)
persists, replace the memory modules. See "Installing Memory
Modules" in "Installing System Board Options." If the problem still
assistance.
Unsupported CPU detected in
Socket n
Microprocessor not supported by
system
Install a correct version of the microprocessor in the specified
"Installing System Board Options."
Unsupported CPU speed detected!
Unsupported CPU speed in CMOS
Microprocessor not supported by
BIOS
Upgrade the BIOS. See "Using the System Setup Program," in the
User's Guide for instructions.
Unsupported DIMM installed in
the RAID DIMM slot!
RAID DIMM not supported by
system
Install a correct version of the RAID DIMM. See "Activating the
Integrated RAID Controller" in "Installing System Board Options."
Unsupported RAID key detected!
RAID hardware key not supported by Install the RAID hardware key for your specific system. See
system
Board Options."
Utility partition not available
<F10> key was pressed during
Create a utility partition on the boot hard-disk drive. See "Using the
POST, but no utility partition exists on Dell OpenManage Server Assistant CD" in your User's Guide.
the boot hard-disk drive
Warning! Detected mode switch
from RAID to SCSI on the onboard
RAID channel. Data loss will
occur! Press Y to confirm the
change; press any other key to
cancel.
Type of controller has changed since Back up information on the drives before changing the type of
previous system boot
controller used with the hard-disk drives.
Write fault
Faulty diskette or hard-disk drive
Write fault on selected drive
NOTE: For the full name of an abbreviation or acronym used in this table, see "Abbreviations and Acronyms."
System Beep Codes
When an error that cannot be reported on the monitor occurs during a boot routine, the system may emit a series of beeps that identify the problem. The beep code is a
pattern of sounds; for example, one beep followed by a second beep and then a burst of three beeps (code 1-1-3) means that the system was unable to read the data
in NVRAM. This information is valuable to the Dell technical support representative if you need to call for technical assistance.
NOTE: If the system boots without a keyboard, mouse, or monitor attached, the system will not issue beep codes related to these peripherals.
When a beep code is emitted, record it on a copy of the Diagnostics Checklist in "Getting Help," and then look it up in Table 2-4. If you are unable to resolve the
problem by looking up the meaning of the beep code, use the Dell Diagnostics to identify a more serious cause. If you are still unable to resolve the problem, see
Table 2-4. System Beep Codes
Code
1-1-3
1-1-4
Cause
Corrective Action
CMOS write/read failure
BIOS checksum failure
This fatal error usually requires that you replace the BIOS firmware. See "Getting Help," for instructions on obtaining
technical assistance.
1-2-1
Programmable interval-timer Replace the system board. See "Getting Help," for instructions on obtaining technical assistance.
failure
1-2-2
1-2-3
DMA initialization failure
DMA page register
write/read failure
Remove and reseat the memory modules. See "Installing Memory Modules" in "Installing System Board Options." If the
problem persists, replace the memory modules. See "Installing Memory Modules" in "Installing System Board Options." If
1-3-1
1-3-2
1-3-3
Main-memory refresh
verification failure
Remove and reseat the memory modules. See "Installing Memory Modules" in "Installing System Board Options." If the
problem persists, replace the memory modules. See "Installing Memory Modules" in "Installing System Board Options." If
No memory installed
Remove and reseat the memory modules. See "Installing Memory Modules" in "Installing System Board Options." If the
problem persists, replace the memory modules. See "Installing Memory Modules" in "Installing System Board Options." If
Chip or data line failure in
the first 64 KB of main
memory
Remove and reseat the memory modules. See "Installing Memory Modules" in "Installing System Board Options." If the
problem persists, replace the memory modules. See "Installing Memory Modules" in "Installing System Board Options." If
1-3-4
1-4-
Odd/even logic failure in the Remove and reseat the memory modules. See "Installing Memory Modules" in "Installing System Board Options." If the
first 64 KB of main memory problem persists, replace the memory modules. See "Installing Memory Modules" in "Installing System Board Options." If
Address line failure in the
first 64 KB of main memory
1-4-2
2-1-1
Parity failure in the first 64
KB of main memory
Bit failure in the first 64 KB
through of main memory
2-4-4
3-1-1
3-1-2
3-1-3
Slave DMA-register failure Replace the system board. See "Getting Help," for instructions on obtaining technical assistance.
Master DMA-register failure
Master interrupt-mask
register failure
3-1-4
3-2-4
Slave interrupt-mask register
failure
Keyboard-controller test
failure
Check the keyboard cable and connector for proper connection. If the problem persists, run the keyboard test in the Dell
Diagnostics to determine whether the keyboard or keyboard controller is faulty. If the keyboard controller is faulty, replace
3-3-1
CMOS failure
Run the system board test in the Dell Diagnostics to isolate the problem.
3-3-2
3-3-3
System configuration check Replace the system board. See "Getting Help," for instructions on obtaining technical assistance.
failure
Keyboard controller not
detected
3-3-4
3-4-2
3-4-3
Screen initialization failure
Screen-retrace test failure
Run the video test in the Dell Diagnostics.
Search for video ROM
failure
4-2-1
4-2-2
4-2-3
4-2-4
No timer tick
Ensure that all expansion cards are properly seated, and then reboot the system.
Shutdown failure
Gate A20 failure
Unexpected interrupt in
protected mode
4-3-1
Improperly seated or faulty Remove and reseat the memory modules. See "Installing Memory Modules" in "Installing System Board Options." If the
memory modules
problem persists, replace the memory modules. See "Installing Memory Modules" in "Installing System Board Options." If
4-3-3
4-3-4
Defective system board
Time-of-day clock stopped Replace the battery. See "Replacing the System Battery" in "Installing System Board Options." If the problem persists,
4-4-1
4-4-2
4-4-3
Super I/O chip failure
(defective system board)
Remove and reseat the specified microprocessor. See "Adding or Replacing a Microprocessor" in "Installing System Board
Parallel-port test failure
(defective system board)
Math coprocessor failure
(defective microprocessor) Options." If the problem persists, replace the microprocessor. See "Adding or Replacing a Microprocessor" in "Installing
System Board Options." If the problem still persists, see "Getting Help," for instructions on obtaining technical assistance.
4-4-4
Cache test failure (defective Remove and reseat the specified microprocessor. See "Adding or Replacing a Microprocessor" in "Installing System Board
microprocessor)
Options." If the problem persists, replace the microprocessor. See "Adding or Replacing a Microprocessor" in "Installing
System Board Options." If the problem still persists, see "Getting Help," for instructions on obtaining technical assistance.
NOTE: For the full name of an abbreviation or acronym used in this table, see "Abbreviations and Acronyms."
Warning Messages
A warning message alerts you to a possible problem and asks you to take corrective action before the system continues a task. For example, before you format a
diskette, a message may warn you that you may lose all data on the diskette, as a way to protect against inadvertently erasing or writing over the data. These warning
messages usually interrupt the procedure and require you to respond by typing y(yes) or n(no).
NOTE: Warning messages are generated by either the application program or the operating system. See "Finding Software Solutions," and the documentation
that accompanied the operating system and application program for more information on warning messages.
Diagnostics Messages
When you run a test group or subtest in the Dell Diagnostics, an error message may result. These particular error messages are not covered in this section. Record the
message on a copy of the Diagnostics Checklist (see "Getting Help"), and then follow the instructions in that section for obtaining technical assistance.
Alert Log Messages From the Dell OpenManage Server Agent
The optional Dell OpenManage Server Agent management application program generates alert messages that appear in the SNMP trap log file. To see the trap log,
select any enterprise under the SNMP trap log icon. Alert log messages consist of information, status, warning, and failure messages for drive, temperature, fan, and
power conditions. More information about the Alert Log window and options is provided in the Dell OpenManage Server Agent documentation found on the Dell
Online Documentation CD.
Finding Software Solutions
Dell™ PowerEdge™ 2500 Systems Installation and Troubleshooting Guide
Because most systems have several application programs installed in addition to the operating system, isolating a software problem can be confusing. Software errors
can also appear to be hardware malfunctions at first.
Software problems can result from the following circumstances:
l
l
l
l
Improper installation or configuration of a program
Input errors
Device drivers that may conflict with certain application programs
Interrupt conflicts between devices
You can confirm that a system problem is caused by software by running the Dell Diagnostics. If all tests in the test group are completed successfully, the problem is
most likely caused by software.
This section provides some general guidelines for analyzing software problems. For detailed troubleshooting information on a particular program, see the documentation
that accompanied the software or consult the support service for the software.
Installing and Configuring Software
Use virus-scanning software to check newly acquired programs and files for viruses before installing the programs on the system's hard-disk drive. Viruses can quickly
use all available system memory, damage and/or destroy data stored on the hard-disk drive, and permanently affect the performance of the programs they infect.
Several commercial virus-scanning programs are available for purchase.
Before installing a program, read its documentation to learn how the program works, what hardware it requires, and what its defaults are. A program usually includes
installation instructions in its accompanying documentation and a software installation routine.
The software installation routine assists users in transferring the appropriate program files to the system's hard-disk drive. Installation instructions may provide details
about how to configure the operating system to successfully run the program. Always read the installation instructions before running a program's installation routine.
When you run the installation routine, be prepared to respond to prompts for information about how the system's operating system is configured, what type of system
you have, and what peripherals are connected to the system.
Using Software
The following subsections discuss errors that can occur as a result of software operation or configuration.
Error Messages
Error messages can be produced by an application program, the operating system, or the system. Messages and Codes discusses the error messages that are
generated by the system. If you receive an error message that is not listed in "Indicators, Messages, and Codes," check the operating system or application program
documentation.
Input Errors
If a specific key or set of keys is pressed at the wrong time, a program may give you unexpected results. See the documentation that came with the application program
to make sure that the values or characters you are entering are valid.
Make sure that the operating environment is set up to accommodate the programs you use. Keep in mind that whenever you change the parameters of the system's
operating environment, you may affect the successful operation of the programs. Sometimes, after modifying the operating environment, you may need to reinstall a
program that no longer runs properly.
Program Conflicts
Some programs may leave portions of their setup information behind, even though you have exited from them. As a result, other programs cannot run. Rebooting the
system can confirm whether these programs are the cause of the problem.
Device drivers, which are programs that use specialized subroutines, can cause problems with the system. For example, a variation in the way the data is sent to the
monitor may require a special screen driver program that expects a certain kind of video mode or monitor. In such cases, you may have to develop an alternate method
of running that particular program—by creating a start-up file made especially for that program, for example. Call the support service for the software you are using to
help you with this problem.
Avoiding Interrupt Assignment Conflicts
Problems can arise if two devices attempt to use the same IRQ line. To avoid this type of conflict, check the documentation for the IRQ line's default for each installed
Table 3-1. IRQ Line Assignment Defaults
IRQ Line
IRQ0
Used By/Available
Used by the system timer
IRQ1
Used by the keyboard controller
Used by interrupt controller 1 to enable IRQ8 through IRQ15
Used by serial port 2 (COM2 and COM4)
Used by serial port 1 (COM1 and COM3)
Available unless used by a secondary parallel port
Used by the diskette drive controller
Used by the primary parallel port
Used by the real-time clock
IRQ2
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
IRQ8
IRQ9
Used for power management functions
Available
IRQ10
IRQ11
IRQ12
IRQ13
IRQ14
IRQ15
Available
Used by the PS/2 mouse port unless the mouse is disabled in the System Setup program
Used by the math coprocessor
IDE CD-ROM controller
Embedded server management
NOTE: For the full name of an abbreviation or acronym used in this table, see the abbreviations and acronyms list at the end of this guide.
Running the Dell™ Diagnostics
Dell™ PowerEdge™ 2500 Systems Installation and Troubleshooting Guide
Unlike many diagnostic programs, the Dell Diagnostics helps you check the system's hardware without any additional equipment and without destroying any data. By
using the diagnostics, you can have confidence in the system's operation. If you find a problem that you cannot solve by yourself, the diagnostic tests can provide you
with important information you will need when talking to Dell's technical assistance representative.
NOTICE: Use the Dell Diagnostics to test only Dell systems. If you use this program with other systems, incorrect system responses or error messages may
result.
Features of the Dell Diagnostics
The Dell Diagnostics provides a series of menus and options from which you choose particular device groups or devices. You can also control the sequence in which
the tests are run. The diagnostic menus also have these helpful features:
l
l
l
l
l
l
l
Options that let you run tests individually or collectively
An option that allows you to choose the number of times a test is repeated
The ability to display or print test results or to save them in a file
Options to temporarily suspend testing if an error is detected or to terminate testing when an adjustable error limit is reached
Help messages that briefly describe each test and its parameters
Status messages that inform you whether device group or device tests are completed successfully
Error messages that appear if any problems are detected
When to Use the Dell Diagnostics
Whenever a major component or device in the system does not function properly, you may have a component failure. As long as the microprocessor and the input and
output components of the system (the monitor, keyboard, and diskette drive) are working, you can use the Dell Diagnostics. If you know what component(s) you need
to test, simply select the appropriate diagnostic device group(s) or subtest(s). If you are unsure about the scope of the problem, read the rest of the information in this
section.
Starting the Dell Diagnostics
You can run the Dell Diagnostics from either the utility partition on your hard-disk drive or from a set of diskettes that you create from the Dell OpenManage Server
Assistant CD.
To run the diagnostics from the utility partition, perform the following steps:
1. Start the utility partition by pressing <F10> during POST.
2. From the utility partition's main menu, select the Run System Diagnostics option from Run System Utilities.
See "Utility Partition" in "Using the Dell OpenManage Server CD," in the User's Guide for additional information about the utility partition.
To run the Dell Diagnostics from the diskettes, perform the following steps:
1. Create a set of diagnostics diskettes using the Dell OpenManage Server Assistant CD.
See "Using the Dell OpenManage Server CD," in the User's Guide for information on creating diskettes.
2. Boot the system from the first diagnostics diskette.
If the system fails to boot, see "Getting Help," for instructions on obtaining technical assistance.
When you start the diagnostics a message is displayed telling you that the diagnostics is loading. The Diagnostics menu appears. The menu allows you to run all or
specific diagnostic tests or to exit the Dell Diagnostics.
NOTE: Before you read the rest of this section, you may want to start the Dell Diagnostics so that you can see it on your monitor screen.
For a quick check of the system, select Test All Devices and then select Quick Tests. This option runs only the device tests that do not require user interaction and
that do not take a long time to run. Dell recommends that you choose this option first to increase the chance of tracing the source of the problem quickly. For a
complete check of the system, select Test All Devices and then select Extended Tests. To check a particular area of the system, choose Advanced Testing.
Selecting Exit to MS-DOS exits the diagnostics and returns you to the MS-DOS® operating system environment.
To select an option from the Diagnostics menu, highlight the option and press <Enter>, or press the key that corresponds to the highlighted letter in the option you
choose.
How to Use the Dell Diagnostics
When you select Select Devices to Test from the Diagnostics menu, the main screen of the diagnostics appears.
Information on the main screen of the diagnostics is presented in the following areas:
l
l
Two lines at the top of the main screen identify the diagnostics and give its version number.
On the left side of the screen, the Device Groups area lists the diagnostic device groups in the order they will run if you select All under the Run Tests
submenu. Press the up- or down-arrow key to highlight a device group.
l
l
On the right side of the screen, the Devices for Highlighted Group area lists the specific devices within a particular test group.
Two lines at the bottom of the screen make up the menu area. The first line lists the menu options you can select; press the left- or right-arrow key to highlight an
option. The second line gives information about the highlighted option.
How to Use the Device Groups Menu
The Device Groups menu at the bottom of the screen provides options that enable you to select and run specific diagnostic tests from the diagnostics main screen.
Press the left- and right-arrow keys to select the options on the menu. As you move from one menu option to another, a brief explanation of the highlighted option
appears on the bottom line of the screen.
If you want more information about a device group or device, highlight the Help option and press <Enter>. After you read the information, press <Esc> to return to the
previous screen.
Device Groups Menu Options
Five options are listed at the bottom of the diagnostics main screen: Run Tests, Devices, Select, Config, and Help.
There are two ways to select a menu option:
l
l
Look on the screen to see which letter in the option is capitalized, and type that letter (for example, type r to select the Run option).
Move the highlight to the option you want to select by pressing the left- or right-arrow key, and then press <Enter>.
Whenever one of the options is selected, additional choices become available.
The following subsections explain the menu options as listed from left to right in the Device Groups menu.
Run Tests
Run Tests displays seven options: One, All, Select, Options, Results, Errors, and Help. If you select One, all the devices within the highlighted device group are
run. If you select All, all of the tests in all of the device group tests are run. (The device group tests are run in the same order as they are listed.) If you choose Select,
only the selected device groups or the devices that you selected within the device groups are run. Before you test any device groups or devices, consider setting global
parameters within Options. Global parameters offer you greater control over how the device group tests or device tests are run and how results are reported. Help
displays a series of help options, including Menu, Keys, Device, Group, and Test.
Devices
Most of the device groups consist of several devices. Use the Devices option to select individual devices within the device group(s).
When you select Devices, the following options are displayed: Run Tests, Tests, Select, Parameters, and Help. Table 4-1 lists all of the possible values for each
option.
Table 4-1. Devices Options
Option
Functions
Run Tests Displays five options: Run Tests, Tests, Select, Parameters, and Help.
Tests
Allows you to select individual devices to tailor the testing process to your particular needs. You can choose one or more devices from the list. When
you choose Tests, four options are displayed: Run Tests, Select, Parameters, and Help.
Select
Allows you to choose one or more devices from a particular device group. Three options are displayed: One, All, and Help.
Parameters Determines how a particular test will be run. Table 4-2 lists all of the possible values for each option. To change Parameters options, press the
spacebar, the left- and right-arrow keys, or the plus (+) and minus (-) keys.
Help
Displays a list of help topics.
Table 4-2. Parameters Options
Option
Possible Values
Number of Times to Repeat Test(s) 0001 through 9999 or 0000, which loops indefinitely until you press <Ctrl><Break>. The default is 1.
Maximum Errors Allowed
Pause for User Response
0000 through 9999, where 0000 means that there is no error limit. The default is 1.
Yes, No
Allows you to decide whether tests will wait for user input.
The default is Yes to wait for user input.
Message Logging
None, Errors, All
Determines if any test results are saved to a file. The default is None.
Message Logging File Name
Specifies the name of the logging file if the Message Logging option is selected. The default is A: RESULT.
Select
The Select option in the Device Groups menu allows you to choose one or more devices from a particular device group. Three options are displayed: One, All, and
Help.
Config
Choosing Config from the Device Groups menu displays information about the particular device that is highlighted.
Error Messages
When you run a test in the diagnostics, error messages may result. Record the messages on a copy of the Diagnostics Checklist; also see "Getting Help," for instructions
on obtaining technical assistance and informing the technical assistance representative of these messages.
Troubleshooting Your System
Dell™ PowerEdge™ 2500 Systems Installation and Troubleshooting Guide
If your system is not working as expected, begin troubleshooting using the procedures in this section. This section guides you through some initial checks and
procedures that can solve basic system problems and provides troubleshooting procedures for components inside the system. Before you start any of the procedures in
this section, take the following steps:
l
l
l
l
Lay the system on its side.
Read the "Safety Instructions" in your System Information document.
Get the key to the system keylock.
Safety First—For You and Your System
The procedures in this guide require that you remove the cover and work inside the system. While working inside the system, do not attempt to service the system
except as explained in this guide and elsewhere in Dell documentation. Always follow the instructions closely. Make sure to review all of the procedures in "Safety
Instructions" in your System Information document.
Working inside the system is safe—if you observe the following precautions.
WARNING: The power supplies in this system produce high voltages and energy hazards, which can cause bodily harm. Only trained service
technicians are authorized to remove the system cover and access any of the components inside the system.
CAUTION: See "Protecting Against Electrostatic Discharge" in the Safety Instructions in your System Information document before performing
any procedure which requires you to open the cover.
External Connections
Improperly set switches, controls, and loose or improperly connected cables are the most likely source of problems for the system, monitor, or other peripherals (such
as a printer, keyboard, mouse, or other external equipment). A quick check of all the switches, controls, and cable connections can easily solve these problems. See
Checking Specific System Problems
1. Turn off the system, including any attached peripherals. Disconnect all the power cables from their electrical outlets.
2. If the system is connected to a PDU, turn the PDU off and then on again.
If it is not receiving power, plug it into another electrical outlet. If it still is not receiving power, try another PDU.
3. Reconnect the system to the electrical outlet or PDU.
4. Is the monitor working properly?
5. Is the keyboard working properly?
6. Are the mouse and printer working properly?
Start-Up Routine
Looking at and listening to the system is important in determining the source of a problem. Look and listen during the system's start-up routine for the indication
Table 5-1. Start-Up Routine Indications
Look/Listen for:
Action
An error message
Alert messages from the Dell OpenManage Server Agent software See "Alert Log Messages From the Dell OpenManage Server Agent" in "Indicators, Messages,
and Codes."
The monitor's power indicator
The keyboard indicators
The diskette-drive access indicator
The hard-disk drive activity indicators
A series of beeps
An unfamiliar constant scraping or grinding sound when you
access a drive
System Orientation
Figure 5-1 shows the rack-mounted and tower version of your system. The illustrations in this document are based on the tower version. Most of the illustrations will
depict the system laying on its side.
Figure 5-1. System Orientation
Removing and Replacing the Front Bezel
The front bezel has status and attention indicators. Swinging the front bezel open provides access to the power switch, diskette drive, CD-ROM drive, hard-disk drive
(s), and power supplies. You must open or remove the front bezel and remove the system cover to gain access to internal components.
Removing the Front Bezel
1. Using the system key, unlock the front bezel.
Figure 5-2. Removing the Front Bezel
4. Rotate the pins upward into the retaining grooves to remove the bezel.
Replacing the Front Bezel
NOTE: The retaining pins are spring loaded. After rotating the pins downward and releasing the pins, they will automatically be inserted into the retaining hinge.
You may need to move the bezel slightly to properly align the pins with the retaining hinge.
1. Align the two bezel retaining pins with the retaining hinge on the front of the system.
2. Rotate the pins downward, and release the pins to attach the bezel to the system.
3. Swing the bezel closed until the bezel snaps into place.
4. Using the system key, lock the bezel.
Removing and Replacing the System Cover
The system is enclosed by a front bezel and a cover. To upgrade or troubleshoot the system, remove the system cover to gain access to internal components.
Removing the System Cover
1. Open the front bezel.
4. Slide the system cover backwards and grasp the cover at both ends.
5. Carefully lift the cover away from the system.
Figure 5-3. Removing the System Cover
Replacing the System Cover
1. Check that no tools or parts are left inside the system.
2. Fit the cover over the sides of the chassis, and slide the cover forward.
3. Secure the cover with the three thumbscrews.
4. Close the front bezel.
Checking the Equipment
This section provides troubleshooting procedures for equipment that connects directly to the I/O panel of the system, such as the monitor, keyboard, or mouse. Before
Troubleshooting the Video Subsystem
Problem
l
l
l
l
Monitor
Monitor interface cable
Video memory
Video logic
Action
1. Check the system and power connections to the monitor.
2. Run the video tests in the Dell Diagnostics.
If the tests run successfully, the problem is not related to video hardware. Go to "Finding Software Solutions."
If the tests did not run successfully see "Getting Help" for instructions on obtaining technical assistance.
Troubleshooting the Keyboard
Problem
l
A system error message indicates a keyboard problem
Action
1. Look at the keyboard and the keyboard cable for any signs of damage.
2. Press and release each key on the keyboard.
If the keyboard and its cable appear to be free of physical damage, and the keys work, go to step 4.
If the keyboard or its cable are damaged, continue to step 3.
3. Swap the faulty keyboard with a working keyboard.
If the problem is resolved, the keyboard must be replaced. See "Getting Help," for instructions on obtaining technical assistance.
4. Run the keyboard test in the Dell Diagnostics.
If you can use the keyboard to select the keyboard test, go to step 6.
If you cannot use the keyboard to select the keyboard test, continue to step 5.
5. Swap the faulty keyboard with a working keyboard.
6. Did the keyboard test run successfully?
If the problem is resolved, the keyboard must be replaced. If the problem is not resolved, the keyboard controller on the system board is faulty. See "Getting
Help," for instructions on obtaining technical assistance.
Troubleshooting the Basic I/O Functions
Problem
l
l
A system error message indicates an I/O port problem
A device connected to the port does not function properly
Action
1. Enter the System Setup program, and check the Serial Port 1, Serial Port 2, and Parallel Port settings.
If the communications ports are set to Enabled, go to step 3.
If the communications ports are not set to Enabled, continue to step 2.
2. Change the Serial Port 1, Serial Port 2, and Parallel Port settings to Enabled; then reboot the system.
3. Check the system setup. See "Using the System Setup Program" in the User's Guide for instructions.
If the system setup is correct, go to step 5.
4. Change the necessary statements in the system setup. If the port problem is confined to a particular application program, see the application program's
documentation for specific port configuration requirements.
5. Reboot the system from the diagnostics diskette, and run the serial ports test and/or the parallel ports test in the Dell Diagnostics.
If the tests did not run successfully, see "Getting Help," for instructions on obtaining technical assistance.
6. If the problem persists, see one of the following procedures, "Troubleshooting a Parallel Printer" or "Troubleshooting a Serial I/O Device," depending on the
malfunctioning device.
Troubleshooting a Serial I/O Device
Problem
l
Device connected to one of the serial ports is not working
Action
1. Turn off the system and any peripheral devices connected to the serial ports.
If there is only one serial device connected to the system, go to step 4.
2. Disconnect the devices from the serial ports, and connect the malfunctioning device to the other port.
3. Turn on the power to the system.
If the problem is resolved, the serial port may be defective. See "Getting Help," for instructions on obtaining technical assistance.
4. Swap the interface cable with a known working cable.
If the problem is resolved, the interface cable must be replaced. See "Getting Help," for instructions on obtaining technical assistance.
5. Turn off the system and the serial device, and swap the device with a comparable device.
6. Turn on the power to the system and the serial device.
If the problem is resolved, the serial device must be replaced. If the problem is not resolved, see "Getting Help," for instructions on obtaining technical assistance.
Troubleshooting a Parallel Printer
Problem
l
Parallel printer is not working
Action
1. Turn off the power from the printer and the system.
2. Swap the parallel printer interface cable with a known working cable.
3. Turn on the power to the printer and the system.
4. Attempt to print with the printer.
If the print operation is successful, the interface cable must be replaced. See "Getting Help," for instructions on obtaining technical assistance.
5. Run the printer's self-test.
If the self-test is not successful, the printer is probably defective. If the printer was purchased from Dell, see "Getting Help," for instructions on obtaining technical
assistance.
6. Attempt to print on the parallel printer.
If the print operation is not successful, the see "Getting Help," for instructions on obtaining technical assistance.
Troubleshooting a USB Device
Problem
l
l
A system error message indicates a problem.
Device connected to the port is not working.
Action
1. Enter the System Setup program, and check that the USB ports are enabled. See "Using the System Setup Program" in the User's Guide for instructions.
2. Turn off the system and any USB devices.
If there is only one USB device connected to the system, go to step 5.
3. Disconnect the USB devices, and connect the malfunctioning device to the other port.
4. Apply power to the system and the reconnected device.
If the problem is resolved, the USB port may be defective. See "Getting Help," for instructions on obtaining technical assistance.
5. If possible, swap the interface cable with a known working cable.
If the problem is resolved, the interface cable must be replaced. See "Getting Help," for instructions on obtaining technical assistance.
6. Turn off the system and the USB device, and swap the device with a comparable device.
7. Turn on the power to the system and the USB device.
If the problem is resolved, the USB device must be replaced. If the problem is not resolved, see "Getting Help," for instructions on obtaining technical assistance.
Troubleshooting the Integrated NIC
Problem
l
NIC cannot communicate with net
Action
1. Enter the System Setup program and confirm that the NIC is enabled.
See "Using the System Setup Program" in the User's Guide for instructions.
2. Check the two indicators on the left and right corners of the NIC connector on the system's back-panel (see Figure 5-4).
The green link indicator shows that the adapter is connected to a valid link partner. The amber activity indicator lights if network data is being sent or received.
l
l
l
If the link indicator is not on, check all cable connections.
Try changing the auto-negotiation setting, if possible.
Try another port on the switch or hub.
3. If the activity indicator does not light, the network driver files might be damaged or deleted.
4. Reinstall the drivers.
5. Make sure the appropriate drivers are installed and the protocols are bound.
Figure 5-4. NIC Indicators
Inside the System
In Figure 5-5, the system cover and front bezel are removed to provide an interior view of the system.
Figure 5-5. Inside the System
The system board holds the system's control circuitry and other electronic components. Several hardware options such as the microprocessors and memory are
installed directly on the system board. The system board can accommodate up to seven PCI expansion cards (two cards at 64-bit/66 MHz, three cards at 64-bit/33
MHz, and two cards at 32-bit/33 MHz). The peripheral bay provides space for a 3.5-inch diskette drive and a CD-ROM drive and two other devices (hard-disk
drives, tape drives).
The hard-disk drive bays provide space for up to six 1-inch SCSI hard-disk drives. These hard-disk drives are connected to a SCSI host adapter on the system board
or on an expansion card, via the SCSI backplane board.
Power is supplied to the system board, SCSI backplane board, and internal peripherals via a single non-redundant power supply. There is an option for up to three
hot-pluggable redundant power supplies that are front loadable and slide into connectors mounted on the the PDB. When this option is installed, the PDB will provide
power to the system board, SCSI backplane board, and internal peripherals.
For non-SCSI drives such as the diskette drive and CD-ROM drive, an interface cable connects the interposer board, attached to the diskette drive and CD-ROM
drive, to the system board. For SCSI devices, interface cables connect externally accessible SCSI devices and the SCSI backplane board to a SCSI host adapter
either on the system board or on an expansion card. (For more information, see "Installing Drives").
During an installation or troubleshooting procedure, you may be required to change a jumper. For information on the system board jumpers, see "Jumpers and
Connectors."
Responding to a Dell OpenManage Server Agent Alert Message
The optional Dell OpenManage™ Server Agent management application monitors critical system voltages and temperatures, the system cooling fans, and the status of
the SCSI hard-disk drives in the system. The application generates alert messages that appear in the alert log window. For information about the alert log window and
options, see the Dell OpenManage Server Agent documentation.
Troubleshooting a Wet System
Problem
l
l
l
Liquid spills
Splashes
Excessive humidity
Action
1. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.
2. Remove the system cover.
3. Remove all expansion cards installed in the system.
4. Let the system dry thoroughly for at least 24 hours.
5. Replace the system cover, reconnect the system to the electrical outlet, and turn on the system.
If the system does not start up properly, see "Getting Help," for instructions on obtaining technical assistance.
6. If the system starts up normally, shut down the system and reinstall all expansion cards you removed in step 3.
7. Run the system board tests in the Dell Diagnostics to confirm that the system is working properly.
If the tests did not complete successfully, see "Getting Help," for instructions on obtaining technical assistance.
Troubleshooting a Damaged System
Problem
l
System dropped or damaged
Action
1. Check the following connections:
l
l
Expansion-card connections to the system board
Drive carrier connections to the SCSI backplane board
2. Make sure that all cables are properly connected and that all components are properly seated in their connectors and sockets.
3. Run the system board tests in the Dell Diagnostics.
If the tests did not complete successfully, see "Getting Help," for instructions on obtaining technical assistance.
Troubleshooting the System Battery
Problem
l
l
l
Error message shows problem with the battery
System setup program loses the system configuration information
System date and time will not stay current
Action
1. Check the connection of the coin cell battery to the system board.
WARNING: There is a danger of a new battery exploding if it is incorrectly installed. Replace the battery only with the same or equivalent type
recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions.
2. If the problem is not resolved by reseating the battery, replace the battery.
If the problem is not resolved by replacing the battery, see "Getting Help," for instructions on obtaining technical assistance.
Troubleshooting Redundant Power Supplies
Problem
l
l
Amber fault indicator on the system front panel lights up
Red fault indicator blinks on the power supply or is lit up continuously
Action
1. Open the front bezel.
CAUTION: The power supplies are hot-pluggable. The system requires two power supplies to be installed for the system to operate normally.
The system is in the redundant mode when all three power supplies are installed. Remove and replace only one power supply at a time.
2. While grasping the power supply handle, push down on the release lever and pull the power supply straight out to clear the chassis.
3. Slide the new power supply into the chassis.
Troubleshooting a Cooling Fan
Problem
l
l
Amber fault indicator on the system front bezel lights up
Server management application program issues a fan-related error message
Action
1. Open the front bezel.
2. Remove the system cover.
NOTE: There are two fan assemblies containing two individual fans. One assembly is located near the SCSI backplane board. The other fan assembly is
attached to the back-panel.
CAUTION: The cooling fans are hot-pluggable. To maintain proper cooling while the system is on, only replace one fan at a time.
3. Locate the faulty fan and while pressing the release lever, grasp the fan and lift straight up to clear the fan assembly (see Figure 5-6).
Figure 5-6. Removing a Cooling Fan
4. Reseat the fan in its compartment.
Ensure that the fan connector is firmly seated.
5. If the problem is not resolved, insert a replacement cooling fan.
6. If the replacement fan does not operate, one of the fan bay connectors is faulty.
Troubleshooting Expansion Cards
Problem
l
l
Error message indicates an expansion-card problem
Expansion card seems to perform incorrectly or not at all
Action
1. Turn off the system and disconnect the system from its electrical outlet.
2. Open the front bezel.
3. Remove the system cover.
4. Verify that each expansion card is firmly seated in its connector.
5. Verify that any appropriate cables are firmly connected to their corresponding connectors on the expansion cards.
6. Install the system cover.
7. Connect the system to an electrical outlet and turn on the system. If the problem still exists, go to step 8.
8. Turn off the system and disconnect the system from its electrical outlet.
9. Remove the system cover.
10. Remove all expansion cards installed in the system.
11. Install the system cover.
12. Connect the system to an electrical outlet and turn on the system.
13. Run the system memory tests in the Dell Diagnostics.
If the tests do not complete successfully, see "Getting Help," for information on obtaining technical assistance.
14. Reinstall one of the expansion cards you removed in step 5 and repeat step 6.
Repeat steps 8 and 9, and steps 11 through 13.
15. Repeat step 14 for each of the remaining expansion cards.
If you have reinstalled all of the expansion cards and the system memory tests are still failing, see "Getting Help," for information on obtaining technical assistance.
Troubleshooting System Memory
Problem
l
l
Faulty memory module
Faulty system board
Action
1. Turn on the power to the system, including any attached peripherals.
If there is not an error message, go to step 8.
2. Enter the System Setup program to check the system memory setting.
See "Using the System Setup Program," in the User's Guide for instructions.
3. If the amount of memory installed does match the system memory setting, go to step 9.
4. Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.
CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your System Information document.
5. Remove the system cover.
6. Remove the cooling shroud (see "Removing the Cooling Shroud" in "Installing System Board Options").
7. Reseat the memory modules in their sockets.
8. Install the cooling shroud (see "Installing the Cooling Shroud" in "Installing System Board Options").
9. Replace the system cover, reconnect the system to power, and turn on the system.
10. Enter the System Setup program and check the system memory again.
11. Does the amount of memory installed match the system memory?
If the amount of memory installed does not match the system memory setting, continue to step 13.
12. Reboot the system, and observe the monitor screen and the Num Lock, Caps Lock, and Scroll Lock indicators on the keyboard.
If the monitor screen does remain blank, and the Num Lock, Caps Lock, and Scroll Lock indicators on the keyboard remain on, continue to step 13.
If the monitor screen does not remain blank, and the Num Lock, Caps Lock, and Scroll Lock indicators on the keyboard remain on, continue to step 18.
13. Repeat steps 4 through 6.
NOTE: There are multiple configurations for the memory modules; see "Memory Module Installation Guidelines" in "Installing System Board Options." The
following steps are an example of one configuration.
14. Swap the memory module pair in bank 1 (DIMM_A and DIMM_B) with one of the same capacity.
15. Replace the system cover and reconnect the system to an electrical outlet.
16. Reboot the system, and observe the monitor screen and the indicators on the keyboard.
17. If the problem still exists, repeat steps 14 through 16 for each memory module pair installed.
If the problem is not resolved, see "Getting Help," for instructions on obtaining technical assistance.
18. Run the system memory test in the Dell Diagnostics.
If the test does not complete successfully, see "Getting Help," for instructions on obtaining technical assistance.
Troubleshooting the Video Subsystem
Problem
l
l
l
Monitor not operating
Monitor interface cable not connected correctly or is faulty
Video logic problems
Action
1. Check the system and power connections to the monitor.
2. Run the video tests in the Dell Diagnostics.
If the tests run successfully, the problem is not related to video hardware. See "Finding Software Solutions."
If the tests did not run successfully see "Getting Help," for instructions on obtaining technical assistance.
Troubleshooting the System Board
Problem
l
Error message indicating a system board problem
Action
1. Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.
2. Open the front bezel.
3. Remove the system cover.
4. Remove all expansion cards except the SCSI host adapter card for the boot drive.
5. Replace the system cover, reconnect the system to power, and turn on the system.
6. Run the system board tests in the Dell Diagnostics.
If the tests does not run successfully, see "Getting Help," for instructions on obtaining technical assistance.
7. Turn off the system, disconnect it from power, and remove the system cover.
8. Reinstall one of the expansion cards that you removed in step 4.
9. Replace the system cover, reconnect the system to power, and turn on the system.
10. Run the system board tests again.
Did the tests run successfully?
If the tests does not complete successfully, see "Getting Help," for instructions on obtaining technical assistance.
11. Repeat steps 8 through 10 for the remaining expansion cards that you removed in step 4.
If you have reinstalled all of the expansion cards and the problem still persists, see "Getting Help," for instructions on obtaining technical assistance.
Troubleshooting the Diskette Drive
Problem
l
Error message indicating a diskette drive problem during execution of either the boot routine or the Dell Diagnostics
Action
1. Enter the system setup program, and verify that the system is configured correctly. See "Using the System Setup Program" in the User's Guide for instructions.
2. Run the diskette drive tests in the Dell Diagnostics to see whether the diskette drive now works correctly.
3. Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.
4. Verify that the diskette/CD-ROM drive interface cable is securely connected between the interposer board on the diskette/CD-ROM drive assembly and the
system board.
5. Connect the system to its electrical outlet and turn on the system, including any attached peripherals.
6. Run the diskette drive tests in the Dell Diagnostics to determine whether the diskette drive works correctly.
7. If the drive still does not work, remove all expansion cards.
8. Run the diskette drive tests in the Dell Diagnostics to determine whether the diskette drive now works correctly.
If the test ran successfully, an expansion card may be conflicting with the diskette drive logic, or you may have a faulty expansion card. Continue to step 9.
9. Reinstall one of the expansion cards you removed in step 7.
10. Retest and run the diskette drives test in the Dell Diagnostics to determine whether the diskette drive subsystem now works correctly.
11. Repeat steps 9 and 10 until all expansion cards have been reinstalled or until one of the expansion cards prevents the system from booting from the diagnostics
diskette.
If the problem is not resolved, see "Getting Help," for instructions on obtaining technical assistance.
Troubleshooting a CD-ROM Drive
Problem
l
l
System cannot read data from CD
CD-ROM indicator fails to flash during boot
Action
1. Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.
2. Open the front bezel.
3. Remove the system cover.
4. Verify that the diskette/CD-ROM drive interface cable is securely connected between the interposer board on the diskette/CD-ROM drive assembly and the
system board.
5. Connect the system to its electrical outlet and turn on the system, including any attached peripherals.
6. Run the IDE devices tests in the Dell Diagnostics to determine whether the CD-ROM drive now works correctly.
If the problem is not resolved, see "Getting Help," for instructions on obtaining technical assistance.
Troubleshooting an External SCSI Tape Drive
Problem
l
l
l
l
Defective tape drive
Defective tape cartridge
Software or device driver
Defective SCSI host adapter
l
Tape drive online indicator fails to light after operating system installs
Action
1. Remove the tape that was in use when the problem occurred and replace it with a tape that you know is not defective.
2. Verify that any required SCSI device drivers are installed on the hard-disk drive and are configured correctly.
3. See "Using the Dell OpenManage Server Assistant CD" in the User's Guide for instructions on installing and configuring device drivers for the system's
integrated SCSI host adapter or Dell host adapter card.
4. For any other type of SCSI host adapter card, see the documentation that accompanied the SCSI host adapter card.
5. Reinstall the tape backup software as instructed in the tape-backup software documentation.
6. Check the external cable connections to the drive.
a. Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.
b. Check the SCSI cable connection to the host adapter card and the SCSI tape drive. Check the DC power cable connection to the tape drive.
c. Verify that the tape drive is configured for a unique SCSI ID number and that the tape drive is terminated or not terminated as appropriate.
See the documentation for the tape drive for instructions on selecting the SCSI ID and enabling or disabling termination.
d. Reconfigure the tape drive's SCSI ID and termination settings as appropriate. Reinstall the tape drive and reconnect the system to the electrical outlet.
Turn on the system.
e. Replace the SCSI cable that connects the tape drive to the SCSI host adapter. Reconnect the system to the electrical outlet and apply power.
7. If the problem is not resolved, see "Getting Help," for instructions on obtaining technical assistance.
Troubleshooting Hard-Disk Drives
Problem
l
l
l
l
The drive itself
SCSI backplane board
SCSI cable connections to the system board
Systems using an optional Dell host adapter card issue the following signals by using the drive indicator lights adjacent to each hard-disk drive:
¡
¡
¡
Hard drive failure indicator on the control panel lights
If a drive shows signs of imminent failure, the drive online indicator stays on and the drive failure indicator blinks on briefly each second.
If a drive has failed, the drive online indicator turns off and the drive failure indicator blinks on briefly each second.
Action
CAUTION: This troubleshooting procedure can destroy data stored on the hard-disk drive. Before you proceed, back up all the files on the hard-
disk drive.
1. If the integrated SCSI host adapter is being used to control the SCSI backplane board, reboot the system and press <Ctrl><q> to enter the SCSI configuration
utility program.
NOTE: If your system has a Dell PERC 3installed, reboot the system and press <Ctrl><h>. See the documentation supplied with the controller for
information on the configuration utility.
2. Check that the primary SCSI channel is enabled, and reboot the system.
3. Verify that the device drivers are installed and configured correctly.
See the documentation for the system's operating system.
4. Remove the drive carrier and install it in the another drive bay.
5. If the problem is resolved, the SCSI backplane board has a defective connector. See "Getting Help," for instructions on obtaining technical assistance.
6. Check the SCSI cable connections inside the system:
a. Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.
b. Remove the system cover.
c. Check the SCSI cable connection to the SCSI host adapter.
The SCSI cable may be connected to the internal SCSI host adapter on the system board or a SCSI host adapter installed in an expansion slot.
NOTE: If the SCSI cable is connected to the SCSI channel A only, all six hard-disk drives are controlled. If both SCSI channels A and B are connected,
the SCSI channel A controller controls hard-disk drives 0 through 2 (SCSI ID 0-2) and the SCSI channel B controller controls hard-disk drives 3 through
5 (SCSI ID 3-5).
7. Partition and logically format the hard-disk drive. If possible, restore the files to the drive.
To partition and logically format the drive, see the documentation for the system's operating system.
8. If the problem is not resolved, see "Getting Help," for instructions on obtaining technical assistance.
Troubleshooting an Integrated RAID Controller
Problem
l
Error message indicating an integrated RAID controller problem.
Action
1. Enter the System Setup program and check the setting for the integrated RAID controller.
See "Using the System Setup Program" in the User's Guide for instructions.
If the controller is enabled, go to step 8.
2. Change the RAID controller setting to Enabled, and then reboot the system.
3. See the documentation provided with the RAID controller software and check the software settings.
WARNING: Before you perform this procedure, you must turn off the system and disconnect it from its power source. For more information, see
4. Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.
6. Remove the system cover.
7. Remove the cooling shroud.
8. Reseat the RAID memory module in its socket.
See "Adding Memory" in "Installing System Board Options" for general instructions on removing and replacing DIMMs.
9. Reseat the RAID hardware key in its socket.
10. Replace the RAID backup battery.
11. Replace the cooling shroud and system cover, reconnect the system to the electrical outlet, and reboot the system.
If the problem is not resolved, see "Getting Help," for instructions on obtaining technical assistance.
Troubleshooting a RAID Controller Card
Your system may contain an optional RAID controller card. If you encounter problems with a controller, see the RAID controller's documentation for detailed
information on troubleshooting the RAID controller.
Installing System Board Options
Dell™ PowerEdge™ 2500 Systems Installation and Troubleshooting Guide
This section describes how to install the following options:
l
l
l
l
Expansion cards
Memory upgrades
Microprocessor upgrades
Integrated RAID controller
This section also includes instructions for replacing the fan assemblies, cooling shroud, power supplies, RAID battery, and system battery, if necessary.
Use Figure 6-1 to locate the system board features. Table 6-1 describes the system board connectors and sockets.
WARNING: Before you perform this procedure, you must turn off the system and disconnect it from its power source. For more information, see
Figure 6-1. System Board Features
Table 6-1. System Board Connectors and Sockets
Connector or Socket Description
SCSI BACKPLANE
RAID BAT
Hot-pluggable SCSI backplane board interface cable connector
RAID battery connector
BATTERY
System battery connector
COMn
Serial port connectors; sometimes referred to as COM1 and COM2
DIMM_x
Memory module sockets (A–F)
Memory module socket for integrated RAID controller
Ethernet connector
DIMM_RAID
ENET
REAR FAN
FLOPPY/IDE
INTR
Power for the rear fan assembly
Power and data to the diskette/CD ROM interposer board from the system board
Intrusion-alarm switch connectors
Keyboard connector
KYBD
MOUSE
Mouse connector
FRONT PANEL
PARALLEL
POWERn
System control panel connector
Parallel port connector; sometimes referred to as LPT1
Power connector
PROCESSOR_n
Microprocessor sockets
PROCESSOR_n VRM Voltage regulator module connector
RAID_KEY
SLOT_n
SCSIA, SCSIB
USBn
Socket for integrated RAID controller hardware key
Expansion card connectors (SLOT_1—SLOT_7)
Ultra160/m SCSI host adapter connectors
USB connector
VGA
Video connector
NOTE: For the full name of an abbreviation or acronym used in this table, see "Abbreviations and Acronyms ."
Removing and Replacing Fan Assemblies
There are two fan assemblies containing two individual fans. One assembly is located near the SCSI backplane board. The other fan assembly is attached to the back-
panel.
Removing the Front Fan Assembly
2. Remove the system cover.
Figure 6-2. Removing the Front Fan Assembly
4. Swing the fan assembly up and out of the way.
5. Disconnect the fan assembly power cable from the front fan connector on the SCSI backplane board (see Figure A-3).
Replacing the Front Fan Assembly
1. Connect the fan assembly power cable to the front fan connector on the SCSI backplane board (see Figure A-3).
2. Place the fan assembly in the hinge bracket and swing the fan assembly down until the release lever snaps into place.
3. Replace the system cover.
4. Close the front bezel.
Removing the Back Fan Assembly
2. Remove the system cover.
4. Press the release latch and lift the fan assembly straight up to clear the chassis (see Figure 6-3).
Figure 6-3. Removing the Back Fan Assembly
5. Disconnect the fan assembly power cable from the fan connector (REAR FAN) on the system board (see Figure 6-1).
Replacing the Back Fan Assembly
1. Connect the fan assembly power cable to the fan connector (REAR FAN) on the system board (see Figure 6-1).
2. Align the fan assembly with the fan assembly guide on the back-panel, and push down until the fan assembly is firmly seated and the latch is engaged (see
4. Replace the system cover.
5. Close the front bezel.
Removing and Replacing Individual Fans
There are four fans contained in two fan assemblies. The procedure for removing and replacing the four fans are the same.
To remove a fan:
2. Remove the system cover.
CAUTION: The cooling fans are hot-pluggable. To maintain proper cooling while the system is on, only replace one fan at a time.
3. Locate the faulty fan and while pressing the fan release lever, lift the fan straight up to clear the fan assembly (see Figure 6-4).
Figure 6-4. Removing/Replacing a Fan
To replace a fan:
1. Lower the fan into the fan assembly until the fan snaps into position.
2. Replace the system cover.
3. Close the front bezel.
Expansion Cards
Expansion cards are installed on the system board (see Figure 6-1). There are seven expansion card slots available.
The front fan assembly bracket is used to help secure the expansion cards.
Installing an Expansion Card
To install an expansion card, perform the following steps.
WARNING: Before you perform this procedure, you must turn off the system and disconnect it from its power source. For more information, see
1. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.
3. Remove the system cover.
CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your System Information document.
See the documentation that came with the expansion card for information on configuring the card, making internal connections, or otherwise customizing the card
for your system.
5. Release the expansion-card latch, and remove the filler bracket from the expansion slot (see Figure 6-5).
7. Position the expansion-card so that the board-edge connector aligns with the expansion-card connector on the system board.
8. Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated.
Figure 6-5. Installing an Expansion Card
9. When the card is seated in the connector and the card-mounting bracket is aligned with the brackets on either side of it, close the expansion-card latch.
NOTE: SCSI cables connected from an expansion card to the SCSI backplane board should be routed under the front fan assembly.
10. Connect any cables that should be attached to the card.
See the documentation that came with the card for information about its cable connections.
12. Replace the system cover, and then reconnect the system and peripherals to their power sources and turn on the system.
13. Close the front bezel.
Removing an Expansion Card
WARNING: Before you perform this procedure, you must turn off the system and disconnect it from its power source. For more information, see
1. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.
3. Remove the system cover.
5. Disconnect any cables connected to the card.
6. To release the expansion card from the system, rotate the latch away from the expansion-card bracket (see Figure 6-5).
7. Grasp the expansion card by its top corners, and carefully remove it from the expansion-card connector.
8. If you are removing the card permanently, install a metal filler bracket over the empty card-slot opening.
NOTE: Installing a filler bracket over an empty expansion slot is necessary to maintain Federal Communications Commission (FCC) certification of the
system. The brackets also keep dust and dirt out of the system and aid in proper cooling and airflow inside the system.
10. Replace the system cover, and then reconnect the system and peripherals to their power sources and turn on the system.
11. Close the front bezel.
Removing and Installing the Cooling Shroud
Removing the Cooling Shroud
2. Remove the system cover.
Figure 6-6. Removing and Installing the Cooling Shroud
4. Rotate the cooling shroud up and lift to clear the rear cooling fan assembly and chassis (see Figure 6-7).
Figure 6-7. Rotating the Cooling Shroud
Installing the Cooling Shroud
1. Lower the cooling shroud into the chassis ensuring that the cooling shroud is aligned with the rear cooling fan assembly guides.
2. Rotate the cooling shroud down ensuring the thumbscrews are aligned with the connecting posts on the system board (see Figure 6-6).
3. Tighten the two thumbscrews securing the cooling shroud to the system board.
4. Replace the system cover.
5. Close the front bezel.
Removing and Installing a Power Supply
CAUTION: The power supplies are hot-pluggable. The system requires two power supplies to be installed for the system to operate normally.
The system is in the redundant mode when all three power supplies are installed. Remove and replace only one power supply at a time.
2. Remove the power supply by grasping the power supply handle, pressing down on the release lever, and pulling the power supply straight out to clear the
Figure 6-8. Removing and Installing the Power Supply
3. Install the power supply by sliding the new power supply into the chassis until it snaps into place.
4. Close the front bezel.
Adding Memory
The six memory module sockets on the system board can accommodate 128 MB to 4 GB of registered SDRAM. The memory module sockets are arranged in pairs
which consist of three banks (Bank 1– Bank 3). These banks are located near the back edge of the system board (see Figure 6-1), next to the cooling fan assembly.
Memory Upgrade Kits
The system is upgradable to 4 GB by installing combinations of 64-,128- 256-, 512-MB, and 1 GB registered memory modules. If you receive an error message
stating that maximum memory has been exceeded, see "Indicators, Messages, and Codes," for detailed information. You can purchase memory upgrade kits from Dell
as needed.
NOTE: The memory modules must be PC-133 compliant.
Memory Module Installation Guidelines
Starting with the socket nearest the fans, the memory module sockets are labeled "DIMM_A" through "DIMM_F" (see Figure 6-9). When you install memory
modules, follow these guidelines:
l
l
You must install memory modules in matched pairs.
Install a pair of memory modules in socket DIMM_A and DIMM_B before installing a second pair in sockets DIMM_C and DIMM_D.
Figure 6-9. Memory Module Sockets
Table 6-2. Sample Memory Module Configurations
Total Desired
Memory
DIMM_A DIMM_B DIMM_C DIMM_D DIMM_E DIMM_F
128 MB
256 MB
512 MB
512 MB
1 GB
64 MB
64 MB
None
None
None
None
128 MB
256 MB
128 MB
256 MB
256 MB
512 MB
512 MB
1 GB
128 MB
256 MB
128 MB
256 MB
256 MB
512 MB
512 MB
1 GB
None
None
None
None
None
None
None
None
128 MB
256 MB
256 MB
512 MB
512 MB
1 GB
128 MB
256 MB
256 MB
512 MB
512 MB
1 GB
None
None
None
None
1.5 GB
2 GB
256 MB
None
256 MB
None
3 GB
512 MB
None
512 MB
None
4 GB
Performing a Memory Upgrade
WARNING: Before you perform this procedure, you must turn off the system and disconnect it from its power source. For more information, see
CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your System Information document.
2. Remove the system cover.
4. Locate the memory module sockets in which you will install or replace memory module pairs. Figure 6-9 shows the order of the memory module sockets.
5. Install or replace the memory module pairs as necessary to reach the desired memory total (see "Installing Memory Modules" or "Removing Memory
Modules").
7. Replace the system cover, reconnect the system to the electrical outlet, and turn on system. After the system completes the POST routine, it runs a memory test.
The system detects that the new memory does not match the system configuration information, which is stored in NVRAM. The monitor displays an error
message that ends with the following words:
Press <F1> to continue; <F2> to enter System Setup
8. Press <F2> to enter the System Setup program, and check the System Memory setting in the system data box on the System Setup screens. The system
should have already changed the value in the System Memory setting to reflect the newly installed memory.
9. If the System Memory value is incorrect, one or more of the memory modules may not be installed properly. Repeat steps 1 through 5 again, checking to
make sure that the memory modules are firmly seated in their sockets.
10. Run the system memory test in the Dell Diagnostics.
11. Close the front bezel.
Installing Memory Modules
WARNING: Before you perform this procedure, you must turn off the system and disconnect it from its power source. For more information, see
CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your System Information document.
2. Remove the system cover.
4. Locate the memory module sockets in which you will install a memory module. Figure 6-9 shows the order of the memory module sockets.
5. Press down and outward on the ejectors on the memory module socket, as shown in Figure 6-10, to allow the memory module to be inserted into the socket.
Figure 6-10. Installing a Memory Module
6. Align the memory module's edge connector with the alignment keys of the memory module socket, and insert the memory module in the socket (see Figure 6-
10).
The memory module socket has two alignment keys that allow the memory module to be installed in the socket in only one way.
7. Press down on the memory module with your thumbs while pulling up on the ejectors with your index fingers to lock the memory module into the socket (see
8. When the memory module is properly seated in the socket, the ejectors on the memory module socket should align with the ejectors on the other sockets with
memory modules installed.
9. Repeat steps 5 through 7 of this procedure to install the remaining memory modules.
Removing Memory Modules
WARNING: Before you perform this procedure, you must turn off the system and disconnect it from its power source. For more information, see
CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your System Information document.
2. Remove the system cover.
4. Locate the memory module sockets in which you will remove memory modules.
5. Press down and outward on the ejectors on each end of the socket until the memory module pops out of the socket (see Figure 6-11).
Figure 6-11. Removing a Memory Module
Microprocessor Upgrades
To take advantage of future options in speed and functionality, you can add a second processor or replace either the primary or secondary processor.
NOTICE: The second processor must be of the same type and speed as the first processor.
Each processor and its associated L2 cache memory are contained in a PGA package that is installed in a ZIF socket on the system board. The following subsection
describes how to install or replace the microprocessor in either the primary or secondary processor socket.
Adding or Replacing a Microprocessor
In addition to the ZIF socket for the primary microprocessor on the system board, there is a second ZIF socket to accommodate a secondary microprocessor. The
secondary micro-processor must have the same operating frequency as the primary micro-processor. For example, if the system has a 933-MHz primary
microprocessor, your secondary microprocessor must also be a 933-MHz microprocessor.
In a single microprocessor system, the microprocessor must be installed in the primary ZIF socket.
The following items are included in the microprocessor upgrade kit:
l
l
l
l
A microprocessor chip
A heat sink
A securing clip
A VRM, if adding a second processor
NOTE: Dell recommends that only a technically knowledgeable person perform this procedure.
2. Remove the system cover.
CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your System Information document.
4. Press down on the heat-sink securing clip to release the clip from the retaining tab on the ZIF socket (see Figure 6-12).
5. Remove the securing clip.
CAUTION: Never remove the heat sink from a microprocessor unless you intend to remove the microprocessor. The heat sink is necessary to
maintain proper thermal conditions.
WARNING: The microprocessor chip and heat sink can become extremely hot. Be sure the microprocessor has had sufficient time to cool before
handling.
Figure 6-12. Securing Clip
6. Remove the heat sink.
7. Pull the socket release lever straight up until the microprocessor is released (see Figure 6-13).
8. Lift the microprocessor out of the socket and leave the release lever up so that the socket is ready for the new microprocessor.
CAUTION: Be careful not to bend any of the pins when removing the microprocessor chip. Bending the pins can permanently damage the
microprocessor chip.
Figure 6-13. Removing the Microprocessor
9. Unpack the new microprocessor.
If any of the pins on the microprocessor appear bent, see "Getting Help," for instructions on obtaining technical assistance from Dell.
10. Align the pin-1 corner of the microprocessor (see Figure 6-14) with the pin-1 corner of the microprocessor socket.
NOTE: Identifying the pin-1 corners is critical to positioning the microprocessor correctly.
Identify the pin-1 corner of the microprocessor by locating the tiny gold triangle that extends from one corner of the large central rectangular area. The gold
triangle points toward pin 1, which is also uniquely identified by a square pad.
Figure 6-14. Pin-1 Identification
CAUTION: Positioning the microprocessor incorrectly can permanently damage the microprocessor and the system when you turn on the
system. When placing the microprocessor in the socket, be sure that all of the pins on the microprocessor go into the corresponding holes. Be
careful not to bend the pins.
If the release lever on the microprocessor socket is not all the way up, move it to that position now.
With the pin-1 corners of the microprocessor and socket aligned, set the microprocessor lightly in the socket and make sure all pins are matched with the correct
holes in the socket. Because the system uses a ZIF micro-processor socket, there is no need to use force (which could bend the pins if the microprocessor is
misaligned). When the microprocessor is positioned correctly, it should drop down into the socket with minimal pressure.
When the microprocessor is fully seated in the socket, rotate the socket release lever back down until it snaps into place, securing the microprocessor.
Figure 6-15. Installing the Microprocessor
Figure 6-16. Installing the Heat-Sink
14. Hook the end of the clip without the heat-sink latch to the tab on the edge of the socket facing the front of the system.
15. Push down and pivot the heat-sink latch until the hole on the clip latches onto the ZIF socket tab.
CAUTION: If you are installing a VRM, it must be a +12V VRM.
17. Make sure that the latches engage.
Figure 6-17. Installing the VRM
19. Replace the system cover making sure that the shroud support holds the shroud in place.
20. Close the front bezel.
21. Reconnect your system and peripherals to their power sources, and turn on system.
22. Press <F2> to enter the System Setup program, and check that the PROCESSOR 1 and PROCESSOR 2 categories match the new system configuration.
See the system User's Guide for instructions.
23. As the system boots, it detects the presence of the new processor and automatically changes the system configuration information in the System Setup program.
If you installed a second microprocessor, the following message is displayed:
Two 933 MHZ Processors, Processor Bus: 133 MHz, L2 cache 256 KB Advanced
If only one processor is installed, the following message is displayed:
One 933 MHz Processor, Processor Bus: 133 MHz, L2 cache 256 KB Advanced
NOTE: After you remove and replace the front bezel, the chassis intrusion detector will cause the following message to be displayed at the next system
start-up:
ALERT! Bezel was previously removed.
24. Enter the System Setup program, and confirm that the top line in the system data area correctly identifies the installed processor(s). See "Using the System
Setup Program" in your User's Guide.
25. While in the System Setup program, reset the chassis intrusion detector.
NOTE: If a setup password has been assigned by someone else, contact your network administrator for information on resetting the chassis intrusion
detector.
26. Run the Dell Diagnostics to verify that the new microprocessor is operating correctly. See "Running the Dell™ Diagnostics," for information on running the
diagnostics and troubleshooting any problems that may occur.
Activating the Integrated RAID Controller
To activate the integrated PERC 3/Di, perform the following steps.
WARNING: Before you perform this procedure, you must turn off the system and disconnect it from its power source. For more information, see
NOTICE: To avoid possible data loss, back up all data on the hard-disk drives before changing the mode of operation of the integrated SCSI controller from
SCSI to RAID.
CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your System Information document.
2. Remove the system cover.
3. Remove the cooling shroud.
4. Open the ejectors on the RAID controller memory module socket down and outward, as shown in Figure 6-18, to allow the memory module to be inserted into
the socket.
Figure 6-18. Installing the RAID Controller Memory Module
5. Align the memory module's edge connector with the slot in the center of the memory module socket, and insert the memory module in the socket (see Figure 6-
18).
The memory module socket has two alignment keys that allow the memory module to be installed in the socket in only one way.
NOTE: The RAID controller memory module must be an unbuffered memory module, rated to run at 100 MHz or faster. Do not substitute registered
memory modules such as those used for system memory.
6. Press on the memory module with your thumbs while pulling on the ejectors with your index fingers to lock the memory module into the socket.
Insert the hardware key into the socket and secure the key with the latches on each end of the socket (see Figure 6-19).
Figure 6-19. Installing the RAID Key
9. Replace the cooling shroud and system cover; reconnect the system and peripherals to their power sources and turn them on.
10. Install the RAID software.
For details, see the RAID controller documentation.
Installing the RAID Battery
1. Hook the front edge of the battery assembly into the slot in the bay, then snap the back edge of the battery assembly into place so the battery lies flat in the bay
2. Connect the battery cable to the RAID battery connector (RAID_BTRY) on the system board (see Figure 6-1).
Removing the RAID Battery
2. Remove the system cover.
4. Disconnect the battery cable from the RAID battery connector (RAID_BTRY) on the system board (see Figure 6-1).
5. Press the release clip on the RAID battery and lift straight up to clear the system (see Figure 6-20).
Figure 6-20. Removing and Installing the RAID Battery
Replacing the System Battery
The system battery maintains system configuration, date, and time information in a special section of memory when you turn off the system. The operating life of the
battery ranges from 2 to 5 years, depending on how you use the system (for example, if you keep the system on most of the time, the battery gets little use and thus
lasts longer). You may need to replace the battery if an incorrect time or date is displayed during the boot routine along with the following or similar message:
Time-of-day not set -- please run SETUP program
Strike the F1 key to continue, F2 to run the setup utility
or
System CMOS checksum bad -- Run SETUP
Strike the F1 key to continue, F2 to run the setup utility
or
Invalid configuration information -- please run SETUP program
Strike the F1 key to continue, F2 to run the setup utility
To determine if the battery needs replacing:
1. Reenter the time and date through the System Setup program.
2. Turn off and disconnect the system from the electrical outlet for a few hours.
3. Reconnect and turn the system on again.
4. Enter the System Setup program.
If the date and time are not correct in the System Setup program, replace the battery.
NOTE: Some software may cause the system time to speed up or slow down. If the system seems to operate normally except for the time kept in the System
Setup program, the problem may be caused by software rather than by a defective battery.
NOTE: If the system is turned off for long periods of time (for weeks or months), the NVRAM may lose its system configuration information. This situation is
not caused by a defective battery.
You can operate the system without a battery; however, the system configuration information maintained by the battery in NVRAM is erased each time you shut down
the system. Therefore, you must reenter the system configuration information and reset the options each time the system boots until you replace the battery.
The battery is a 3.0-volt (V), coin-cell battery. To remove the battery, perform the following steps.
WARNING: Before you perform this procedure, you must turn off the system and disconnect it from its power source. For more information, see
WARNING: There is a danger of a new battery exploding if it is incorrectly installed. Replace the battery only with the same or equivalent type
recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions.
1. Enter the System Setup program and, if possible, make a printed copy of the System Setup screens.
See "Using the System Setup Program," in the User's Guide for instructions.
2. Shut down the system, including any attached peripherals, and disconnect the system from the electrical outlet.
CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your System Information document.
4. Remove the system cover.
6. Pry the battery out of its socket with your fingers or with a blunt, nonconductive object such as a plastic screwdriver.
Figure 6-21. Installing the Battery
8. Replace the system cover, and then reconnect the system and peripherals to their power sources and turn on the system power.
9. Enter the System Setup program to confirm that the battery is operating properly.
10. Enter the correct time and date through the System Setup program's Time and Date settings.
Also reenter any system configuration information that is no longer displayed on the System Setup screens, and then exit the System Setup program.
11. To test the newly installed battery, power down and disconnect the system from the electrical source for at least an hour.
12. Close the front bezel.
13. After an hour, connect the system to an electrical source and turn on the power.
14. Enter the System Setup program and if the time and date are still incorrect, see "Getting Help," for instructions on obtaining technical assistance.
Installing Drives
Dell™ PowerEdge™ 2500 Systems Installation and Troubleshooting Guide
Your system features an internal drive bay that contains up to six SCSI hard-disk drives. Your system also features a removable peripheral bay that incorporates two
drive bays for installing additional SCSI hard-disk drives. Attached to the removable peripheral bay is a user-accessible, half-height, CD ROM drive and a 3.5-inch
diskette drive, which is controlled by the IDE/diskette drive controller on the system board. Instructions are also included for upgrading the system by installing an
optional SCSI backplane daughter card for split backplane operation, or a PERC host adapter card.
Removing the Peripheral Bay
1. Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.
3. Remove the system cover.
4. Remove the front fan assembly (see "Removing the Front Fan Assembly" in "Installing System Board Options").
5. Disconnect the interface cable from the interposer board attached to the CD-ROM/diskette drive.
NOTE: To slide the peripheral bay backward, you may need to disconnect the power cable on the SCSI backplane board.
Figure 7-1. Removing the Peripheral Bay
7. While grasping the peripheral bay handle, slide the peripheral bay backwards and lift the bay straight up to clear the chassis.
Installing the Peripheral Bay
1. Connect the interface cable from the system board to the CD-ROM/diskette drive interposer board.
2. While grasping the peripheral bay handle, lower the peripheral bay into the chassis.
3. Align the tabs on side of the peripheral bay with the locking slots in the chassis and slide the peripheral bay forward.
5. Replace the front fan assembly (see "Replacing the Front Fan Assembly" in "Installing System Board Options").
6. Replace the system cover.
7. Close the front bezel.
Interface Cables
If you install a SCSI device, you will connect it to the secondary SCSI interface connector (SCSI2 [Channel B]) on the system board (see Figure 6-1), or to a SCSI
host adapter on an expansion card.
These interface connectors are keyed for correct insertion. Keying ensures that the pin-1 wire in the cable goes to the pin-1 ends of the connectors on both ends.
When you disconnect an interface cable, take care to grasp the cable connector, rather than the cable itself, to avoid stress on the cable.
SCSI Configuration Information
Although SCSI devices are installed essentially the same way as other devices, their configuration requirements are different. To configure a SCSI device installed in the
peripheral bay, follow the guidelines in the following subsections.
SCSI ID Numbers
Each device attached to a SCSI host adapter must have a unique SCSI ID number from 1 to 7.
When SCSI devices are shipped from Dell, the default SCSI ID numbers are assigned as follows:
l
A SCSI tape drive is configured as SCSI ID 6 (the default ID number for a tape drive).
NOTE: There is no requirement that SCSI ID numbers be assigned sequentially or that devices be attached to the cable in order by ID number.
Device Termination
SCSI logic requires that the two devices at opposite ends of the SCSI chain be terminated and that all devices in between be unterminated. The SCSI cable included in
the upgrade kit has an active terminator installed at the end of the cable. Therefore, when configuring the devices in the peripheral bay, you should disable the devices
termination.
Installing a Device That Uses the System's Integrated SCSI Controller
WARNING: Before you perform this procedure, you must turn off the system and disconnect it from its power source. For more information, see
1. Turn off the power to the system, including any attached peripherals, and disconnect the system from the electrical outlet.
2. Prepare the drive for installation.
CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your System Information document.
Ground yourself by touching an unpainted metal surface on the back of the system, unpack the drive, and compare the jumper and switch settings with those in
the drive documentation. (See "SCSI Configuration Information," for information on setting the drive's SCSI ID number and enabling termination [if required].)
Change any settings necessary for this system's configuration.
4. Remove the system cover.
5. Disconnect the cable connected to the interposer board on top of the peripheral bay.
This cable is the system board interface cable connecting the interposer board of the CD-ROM/diskette drive to the system board.
6. Remove the inserts from the front of the peripheral bay.
From the inside of the chassis, push outwards on the center of the insert to remove the insert from the chassis.
8. Slide the new drive into the peripheral bay until the holes in the peripheral bay and the drive line up.
9. Using four screws, secure the drive to the peripheral bay.
11. Connect the SCSI device to the SCSI cable provided with the device. Attach the other end of the SCSI cable to the interface connector SCSI/Channel B on
the system board.
Route the SCSI cable under the front fan assembly.
12. Check all cable connections that may have been loosened during this procedure. Arrange cables so that they will not catch on the system cover or block the
airflow of the fans or cooling vents.
13. Replace the system cover.
14. Close the front bezel.
15. Reconnect the system and peripherals to their power sources, and turn on the power.
16. Test the device.
To test a tape drive, see the documentation for the tape drive software to perform a tape drive backup and verification test.
Installing a Tape Drive That Uses a Controller Card
Tape drives that require their own separate controller cards are shipped with the controller card and an interface cable.
WARNING: Before you perform this procedure, you must turn off the system and disconnect it from its power source. For more information, see
1. Turn off the power to the system, including any attached peripherals, and disconnect the system from the electrical outlet.
2. Prepare the controller card and drive for installation.
CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your System Information document.
Ground yourself by touching an unpainted metal surface on the back of the system, unpack the drive and controller card, and compare the jumper and switch
settings with those in the drive documentation. (See "SCSI Configuration Information," for information on setting the drive's SCSI ID number and enabling
termination [if required].) Change any settings necessary for this system's configuration.
4. Remove the system cover.
5. Disconnect the cable connected to the interposer board on top of the peripheral bay.
This cable is the system board interface cable connecting the interposer board of the CD-ROM/diskette drive to the system board.
6. Remove the inserts from the front of the peripheral bay.
From the inside of the chassis, push outwards on the center of the insert to remove the insert from the chassis.
8. Slide the tape drive into the peripheral bay until the holes in the peripheral bay and the tape drive line up.
9. Using four screws, secure the drive to the peripheral bay.
11. Install the controller card in an expansion slot (see "Installing an Expansion Card" in "Installing System Board Options").
12. Attach the interface cable that came with the drive kit to the interface connector on the back of the drive.
13. Connect the SCSI device to the SCSI cable provided with the device. Attach the other end of the SCSI cable to interface connector SCSI/Channel B on the
system board.
Route the SCSI cable along the top of the cooling shroud.
14. Check all cable connections that may have been loosened during this procedure. Arrange cables so that they will not catch on the system cover or block the
airflow of the fans or cooling vents.
15. Replace the system cover.
16. Close the front bezel.
17. Reconnect the system and peripherals to their power sources, and turn on the power.
18. Perform a tape backup and verification test with the drive as instructed in the tape-drive software documentation that came with the drive.
Connecting an External SCSI Tape Drive
This subsection describes how to configure and install an external SCSI tape drive.
Installing the Tape Drive
CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your System Information document.
1. Prepare the tape drive for installation.
Ground yourself by touching an unpainted metal surface on the back of the system, unpack the drive and controller card, and compare the jumper and switch
settings with those in the drive documentation. (See "SCSI Configuration Information," for information on setting the drive's SCSI ID number and enabling
termination [if required].) Change any settings necessary for this system's configuration.
2. Unpack the tape drive (and controller card, if applicable), and configure the tape drive for the system according to the documentation that came with the tape
drive.
3. If the tape drive was supplied with a controller card, perform the following steps to install the card:
b. Remove the system cover.
c. Install the controller card in an expansion slot.
d. Replace the system cover.
e. Close the front bezel.
4. Connect the tape drive's interface/DC power cable to the external SCSI connector on the back of the system, or the connector on the controller card supplied
with the tape drive.
5. Secure the controller card connection by tightening the screws on the connector.
6. Reconnect the system and peripherals to electrical outlets, and turn on the power.
7. Perform a tape backup and verification test with the drive as instructed in the software documentation that came with the drive.
Installing SCSI Hard-Disk Drives
This subsection describes how to install and configure SCSI hard-disk drives in the system's internal hard-disk drive bays, and how to upgrade the system by installing
a Dell host adapter card.
The internal hard-disk drive bays provide space for up to six 1-inch hard-disk drives. These drives connect to a SCSI backplane board. A SCSI cable connects the
SCSI backplane board to the SCSI host adapter connector on the system board or to an optional SCSI host adapter card such as the Dell PERC host adapter card.
Before You Begin
Before attempting to remove or install a drive while the system is running, see the documentation for the Dell PERC host adapter card to ensure that the card is
configured correctly to support hot-pluggable drive removal and insertion.
SCSI hard-disk drives are supplied by Dell in special drive carriers that fit in the hard-disk drive bays.
NOTE: Dell recommends that you use only drives that Dell has tested and approved for use with the SCSI backplane board.
Refer to the following guidelines when you configure the SCSI drive:
l
l
l
Disable termination on the drive. The SCSI backplane board provides termination for the SCSI bus.
Set the SCSI ID on all drives to 0. All SCSI ID numbers for the drives are set by the SCSI backplane board.
Configure the drive so that the drive motor waits for a Start Unit command from the SCSI host adapter before spinning.
You may need to use different programs than those provided with the operating system to partition and format SCSI hard-disk drives. See "Installing and Configuring
SCSI Drivers," in the User's Guide for information and instructions.
CAUTION: Do not turn off or reboot your system while the drive is being formatted. Doing so can cause a drive failure.
When you format a high-capacity SCSI hard-disk drive, allow enough time for the formatting to be completed. Long format times for these drives are normal. A 9 GB
hard-disk drive, for example, can take up to 2.5 hours to format.
Installing a SCSI Hard-Disk Drive
NOTICE: Hot-plug drive installation is not supported for systems without an integrated RAID controller or Dell PERC host adapter card.
1. If the system does not have a RAID controller installed, shut down the system.
Figure 7-2. Installing a SCSI Hard-Disk Drive Carrier
5. Close the drive carrier handle to lock the drive in place.
6. Close the front bezel.
7. Install any required SCSI device drivers (see "Installing and Configuring SCSI Drivers," in the User's Guide for information).
8. If the hard-disk drive is a new drive, run the SCSI Controllers test in the Dell Diagnostics.
Removing a SCSI Hard-Disk Drive
NOTICE: Hot-plug drive installation is not supported for systems without an integrated RAID controller or Dell PERC host adapter card.
1. If the system does not have a RAID controller installed, shut down the system.
2. For systems with Dell PERC host adapter cards, power down the hard-disk drive bay and wait until the SCSI hard-disk drive indicator codes on the drive
carrier signal that the drive may be removed safely.
If the drive has been online, the drive status indicators will flash sequentially as the drive is powered down. When all indicators are turned off, the drive is ready
for removal.
4. Open the drive carrier handle to release the carrier.
5. Slide the carrier toward you until it is free of the drive bay.
6. Close the front bezel.
Installing a Dell Host Adapter Card
Follow these general guidelines when installing a Dell host adapter card. For specific instructions, see the documentation supplied with the host adapter card.
WARNING: Before you perform this procedure, you must turn off the system and disconnect it from its power source. For more information, see
CAUTION: See "Protecting Against Electrostatic Discharge" in the Safety Instructions in your System Information document.
1. Unpack the host adapter card, and prepare it for installation.
See the documentation accompanying the host adapter card.
3. Remove the system cover.
4. Remove the SCSI interface cable that connects the SCSI/Channel A host-adapter connector on the system board to the SCSIA connector on the SCSI
5. Install the host adapter card.
If you are installing a Dell PERC host adapter card, install the card in PCI expansion slot 1.
6. Install the SCSI interface cable supplied with the host adapter card to the SCSIA connector on the SCSI backplane board.
To identify the correct connector, see documentation for the host adapter card. Route the SCSI cable under the front fan assembly.
7. Connect the external SCSI devices to the SCSI host adapter card's external connector on the system's back-panel.
If you are attaching multiple external SCSI devices, daisy-chain the devices to each other by using the cables shipped with each device.
8. Replace the system cover.
9. Close the front bezel. Reconnect the system to an electrical outlet.
10. Connect the external device(s) to electrical outlet(s).
11. Install any required SCSI device drivers (see "Installing and Configuring SCSI Drivers," in the User's Guide for information and instructions).
12. Test the SCSI devices.
Test a SCSI hard-disk drive by running the SCSI Controllers test in the Dell Diagnostics. To test a SCSI tape drive, also see the documentation for the tape drive
software to perform a tape drive backup and verification test.
Installing a SCSI Backplane Daughter Card
To operate the SCSI backplane in a 2 x 3 split backplane configuration, you must install an optional daughter card.
WARNING: Before you perform this procedure, you must turn off the system and disconnect it from its power source. For more information, see
1. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.
CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your System Information document.
2. Unpack the SCSI backplane board daughter card kit.
4. Remove the system cover.
5. The daughter card fits between the sides of a card guide on the top of the drive bay. To install the card in the card guide:
a. Hold the daughter card by its edges with the component side facing up and the card connector facing the SCSI backplane board (see Figure 7-3).
b. Ensure that the retention lever is in the open position.
Figure 7-3. Installing a SCSI Backplane Board Daughter Card
c. Position the card in the drive bay so that the notches on the left and right edges of the card are aligned with the tabs on the card guide in the drive
bay.
d. Lower the card into the card guide.
6. Close the retention lever to slide the daughter card into the SCSI backplane connector and lock the card into place (see Figure 7-3).
7. Reconfigure the SCSI cable connections to the SCSI backplane as necessary to operate the backplane as a 2 x 3 split backplane.
8. Replace the system cover.
9. Close the front bezel. Reconnect the system and peripherals to their power sources and turn on power.
Configuring the Boot Device
If you plan to boot the system from a hard-disk drive, the drive must be attached to the primary (or boot) controller or SCSI host adapter card. The device that the
system boots from is determined by the boot order specified in the system setup program.
The system setup program provides options that the system uses to scan for installed boot devices. Refer to the User's Guide for information about the system setup
program.
Getting Help
Dell™ PowerEdge™ 2500 Systems Installation and Troubleshooting Guide
Help Overview
This section describes the tools Dell provides to help you when you have a problem with your computer. It also tells you when and how to contact Dell for technical or
customer assistance.
Technical Assistance
If you need assistance with a technical problem, perform the following steps:
2. Run the Dell diagnostics.
3. Make a copy of the Diagnostics Checklist, and fill it out.
4. Use Dell's extensive suite of online services available at Dell's website (http://www.dell.com) for help with installation and troubleshooting procedures.
5. If the preceding steps have not resolved the problem, call Dell for technical assistance.
When prompted by Dell's automated telephone system, enter your Express Service Code to route the call directly to the proper support personnel. If you do not
have an Express Service Code, open the Dell Accessories folder, double-click the Express Service Code icon, and follow the directions.
NOTE: Dell's Express Service Code system may not be available in all countries.
For instructions on using the technical support service, see "Technical Support Service" and "Before You Call."
Help Tools
Dell provides a number of tools to assist you. These tools are described in the following sections.
NOTE: Some of the following tools are not always available in all locations outside the continental U.S. Please call your local Dell representative for information
on availability.
World Wide Web
The Internet is your most powerful tool for obtaining information about your computer and other Dell products. Through the Internet, you can access most of the
services described in this section, including AutoTech, TechFax, order status, technical support, and product information.
You can access Dell's support website at http://support.dell.com. To select your country, click the map that appears. The Welcome to support.dell.com page
opens. Enter your system information to access help tools and information.
Dell can be accessed electronically using the following addresses:
l
World Wide Web
http://www.dell.com/ap/ (for Asian/Pacific countries only)
http://www.euro.dell.com (for Europe only)
http://www.dell.com/la (for Latin American countries)
Anonymous file transfer protocol (FTP)
ftp.dell.com/
l
Log in as user:anonymous, and use your e-mail address as your password.
l
Electronic Support Service
[email protected] (for Asian/Pacific countries only)
support.euro.dell.com (for Europe only)
Electronic Quote Service
l
[email protected] (for Asian/Pacific countries only)
Electronic Information Service
l
AutoTech Service
Dell's automated technical support service—AutoTech—provides recorded answers to the questions most frequently asked by Dell customers about their portable and
desktop computer systems.
When you call AutoTech, you use your touch-tone telephone to select the subjects that correspond to your questions.
The AutoTech service is available 24 hours a day, seven days a week. You can also access this service through the technical support service. For the telephone
number to call, see "Dell Contact Numbers."
TechFax Service
Dell takes full advantage of fax technology to serve you better. Twenty-four hours a day, seven days a week, you can call the Dell TechFax line toll-free for all kinds of
technical information.
Using a touch-tone phone, you can select from a full directory of topics. The technical information you request is sent within minutes to the fax number you designate.
Automated Order-Status System
You can call this automated service to check on the status of any Dell products that you have ordered. A recording prompts you for the information needed to locate
Technical Support Service
Dell's industry-leading hardware technical-support service is available 24 hours a day, seven days a week, to answer your questions about Dell hardware.
Our technical support staff pride themselves on their track record: more than 90 percent of all problems and questions are taken care of in just one toll-free call, usually
in less than 10 minutes. When you call, our experts can refer to records kept on your Dell system to better understand your particular question. Our technical support
staff use computer-based diagnostics to provide fast, accurate answers to questions.
To contact Dell's technical support service, see "Before You Call" and then call the number for your country as listed in "Dell Contact Numbers."
Problems With Your Order
If you have a problem with your order, such as missing parts, wrong parts, or incorrect billing, contact Dell for customer assistance. Have your invoice or packing slip
Product Information
If you need information about additional products available from Dell, or if you would like to place an order, visit Dell's website at http://www.dell.com/. For the
Returning Items for Warranty Repair or Credit
Prepare all items being returned, whether for repair or credit, as follows:
1. Call Dell to obtain an authorization number, and write it clearly and prominently on the outside of the box.
2. Include a copy of the invoice and a letter describing the reason for the return.
3. Include a copy of the Diagnostics Checklist indicating the tests you have run and any error messages reported by the Dell Diagnostics.
4. Include any accessories that belong with the item(s) being returned (such as power cables, software diskettes, and guides) if the return is for credit.
5. Pack the equipment to be returned in the original (or equivalent) packing materials.
You are responsible for paying shipping expenses. You are also responsible for insuring any product returned, and you assume the risk of loss during shipment to
Dell. Collect-on-delivery (C.O.D.) packages are not accepted.
Returns that are missing any of the preceding requirements will be refused at our receiving dock and returned to you.
Before You Call
NOTE: Have your Express Service Code ready when you call. The code helps Dell's automated-support telephone system direct your call more efficiently.
Remember to fill out the Diagnostics Checklist. If possible, turn on your system before you call Dell for technical assistance and call from a telephone at or near the
computer. You may be asked to type some commands at the keyboard, relay detailed information during operations, or try other troubleshooting steps possible only at
the computer system itself. Make sure that the system documentation is available.
CAUTION: Before servicing any components inside your computer, see "Safety First—For You and Your System."
Dell Contact Numbers
The following table provides country-specific access codes and telephone numbers, websites, and email addresses that you can use to contact Dell.
The codes required depend on where you are calling from as well as the destination of your call; in addition, each country has a different dialing protocol. If you need
assistance in determining which codes to use, contact a local or an international operator.
NOTE: Toll-free numbers are for use only within the country for which they are listed. Area codes are most often used to call long distance within your own
country (not internationally)—in other words, when your call originates in the same country you are calling.
Country (City)
International Access Code
Country Code
Department Name or Service Area,
Website and E-mail Address
Area Codes,
Local Numbers, and Toll Free Numbers
City Code
Australia (Sydney)
International Access Code: 0011
Country Code: 61
Home and Small Business
1-300-65-55-33
toll free: 1-800-633-559
toll free: 1-800-060-889
toll free: 1-800-819-339
toll free: 1-800-808-385
toll free: 1-800-808-312
toll free: 1-800-818-341
01 795 67602
Government and Business
Preferred Accounts Division (PAD)
Customer Care
City Code: 2
Corporate Sales
Transaction Sales
Fax
Austria (Vienna)
Home/Small Business Sales
Home/Small Business Fax
Home/Small Business Customer Care
Preferred Accounts/Corporate Customer Care
Home/Small Business Technical Support
Preferred Accounts/Corporate Technical Support
Switchboard
01 795 67605
International Access Code: 900
Country Code: 43
01 795 67603
0660 8056
City Code: 1
01 795 67604
0660 8779
01 491 04 0
Website: http://support.euro.dell.com
E-mail: [email protected]
Technical Support
Belgium (Brussels)
International Access Code: 00
Country Code: 32
02 481 92 88
02 481 91 19
Customer Care
Home/Small Business Sales
Corporate Sales
toll free: 0800 16884
02 481 91 00
City Code: 2
Fax
02 481 92 99
Switchboard
02 481 91 00
Website: http://support.euro.dell.com
E-mail: [email protected]
Customer Support, Technical Support
Brazil
0800 90 3355
0800 90 3366
International Access Code: 0021
Country Code: 55
Sales
Website: http://www.dell.com/br
City Code: 51
Brunei
Customer Technical Support (Penang, Malaysia)
Customer Service (Penang, Malaysia)
Transaction Sales (Penang, Malaysia)
604 633 4966
604 633 4949
Country Code: 673
604 633 4955
Canada (North York, Ontario) Automated Order-Status System
toll free: 1-800-433-9014
toll free: 1-800-247-9362
toll free: 1-800-387-5759
416 758-2400
AutoTech (Automated technical support)
International Access Code: 011
Customer Care (From outside Toronto)
Customer Care (From within Toronto)
Customer Technical Support
toll free: 1-800-847-4096
toll free: 1-800-387-5752
416 758-2200
Sales (Direct Sales—from outside Toronto)
Sales (Direct Sales—from within Toronto)
Sales (Federal government, education, and medical)
toll free: 1-800-567-7542
Sales (Major Accounts)
toll free: 1-800-387-5755
toll free: 1-800-950-1329
toll free: 1230-020-4823
TechFax
Chile (Santiago)
Sales, Customer Support, and Technical Support
Country Code: 56
City Code: 2
China (Xiamen)
Technical Support
toll free: 800 858 2437
toll free: 800 858 2060
toll free: 800 858 2222
toll free: 800 858 2062
toll free: 800 858 2999
02 22 83 27 27
Customer Experience
Home and Small Business
Preferred Accounts Division
Large Corporate Accounts
Technical Support
Country Code: 86
City Code: 592
Czech Republic (Prague)
International Access Code: 00
Country Code: 420
Customer Care
02 22 83 27 11
Fax
02 22 83 27 14
TechFax
02 22 83 27 28
City Code: 2
Switchboard
02 22 83 27 11
Website: http://support.euro.dell.com
E-mail: [email protected]
Technical Support
Denmark (Horsholm)
International Access Code: 009
Country Code: 45
45170182
45170184
32875505
45170100
859005594
45170117
Relational Customer Care
Home/Small Business Customer Care
Switchboard
Fax Technical Support (Upplands Vasby, Sweden)
Fax Switchboard
Website: http://support.euro.dell.com
E-mail: [email protected]
Technical Support
Finland (Helsinki)
International Access Code: 990
Country Code: 358
City Code: 9
09 253 313 60
09 253 313 81
09 253 313 38
09 693 791 94
09 253 313 99
09 253 313 00
Technical Support Fax
Relational Customer Care
Home/Small Business Customer Care
Fax
Switchboard
Website: http://support.euro.dell.com
E-mail: [email protected]
Home and Small Business
Technical Support
France (Paris/Montpellier)
International Access Code: 00
Country Code: 33
0825 387 270
0825 823 833
0825 004 700
04 99 75 40 39
0825 004 700
0825 004 701
Customer Care
Switchboard
City Code: (1) (4)
Switchboard (Alternative)
Sales
Fax
Website: http://support.euro.dell.com
E-mail: [email protected]
Corporate
Technical Support
0825 004 719
0825 338 339
01 55 94 71 00
01 55 94 71 00
01 55 94 71 99
Customer Care
Switchboard
Sales
Fax
Website: http://support.euro.dell.com
E-mail: [email protected]
Technical Support
Germany (Langen)
International Access Code: 00
Country Code: 49
06103 766-7200
06103 766-9222
0180-5-224400
06103 766-9570
06103 766-9420
06103 766-9560
06103 766-9555
06103 766-7000
Technical Support Fax
Home/Small Business Customer Care
Global Segment Customer Care
Preferred Accounts Customer Care
Large Accounts Customer Care
Public Accounts Customer Care
Switchboard
City Code: 6103
Website: http://support.euro.dell.com
E-mail: [email protected]
Technical Support
Hong Kong
toll free: 800 96 4107
604 633 4949
Customer Service (Penang, Malaysia)
Transaction Sales
International Access Code: 001
Country Code: 852
Ireland (Cherrywood)
International Access Code: 16
Country Code: 353
City Code: 1
toll free: 800 96 4109
toll free: 800 96 4108
0870 908 0800
01 204 4026
Corporate Sales
Technical Support
Customer Care
Sales
01 286 0500
SalesFax
01 204 0144
Fax
0870 907 5590
01 286 0500
Switchboard
Website: http://support.euro.dell.com
E-mail: [email protected]
Home and Small Business
Technical Support
Italy (Milan)
02 577 826 90
02 696 821 14
02 696 824 13
02 696 821 12
International Access Code: 00
Country Code: 39
City Code: 02
Customer Care
Fax
Switchboard
Website: http://support.euro.dell.com
E-mail: [email protected]
Corporate
Technical Support
02 577 826 90
02 577 825 55
02 575 035 30
02 577 821
Customer Care
Fax
Switchboard
Website: http://support.euro.dell.com
E-mail: [email protected]
Technical Support (Server)
Technical Support (Dimension™ and Inspiron™)
Japan (Kawasaki)
International Access Code: 001
Country Code: 81
toll free: 0120-1984-35
toll free: 0120-1982-56
or 0088-25-3355
Technical Support (Workstation, Optiplex™ and Latitude™)
toll free: 0120-1984-39
City Code: 44
or 0088-22-7890
044 556-3801
044 556-4240
044 556-3344
044 556-3433
044 556-3430
24-Hour Automated Order Service
Customer Care
Home and Small Business Group Sales
Preferred Accounts Division Sales
Large Corporate Accounts
Faxbox Service
044 556-3490
Switchboard
044 556-4300
Website: http://support.jp.dell.com
Technical Support
Korea (Seoul)
toll free: 080-200-3800
toll free: 080-200-3777
2194-6220
Sales
International Access Code: 001
Country Code: 82
City Code: 2
Customer Service (Seoul, Korea)
Customer Service (Penang, Malaysia)
Fax
604 633 4949
2194-6202
Switchboard
2194-6000
Latin America
Customer Technical Support (Austin, Texas, U.S.A.)
Customer Service (Austin, Texas, U.S.A.)
Fax (Technical Support and Customer Service)(Austin, Texas, U.S.A.)
Sales (Austin, Texas, U.S.A.)
SalesFax (Austin, Texas, U.S.A.)
512 728-4093
512 728-3619
512 728-3883
512 728-4397
512 728-4600
or 512 728-3772
02 481 92 88
Luxembourg
Technical Support (Brussels, Belgium)
Home/Small Business Sales (Brussels, Belgium)
Corporate Sales (Brussels, Belgium)
Customer Care (Brussels, Belgium)
Fax (Brussels, Belgium)
toll free: 080016884
02 481 91 00
International Access Code: 00
Country Code: 352
02 481 91 19
02 481 92 99
Switchboard (Brussels, Belgium)
Website: http://support.euro.dell.com
E-mail: [email protected]
02 481 91 00
Macau
Technical Support
toll free: 0800 582
604 633 4949
Customer Service (Penang, Malaysia)
Transaction Sales
Country Code: 853
toll free: 0800 581
toll free: 1 800 888 298
Malaysia (Penang)
Technical Support
Customer Service
Transaction Sales
Corporate Sales
04 633 4949
toll free: 1 800 888 202
toll free: 1 800 888 213
International Access Code: 00
Country Code: 60
City Code: 4
Mexico
Automated Order-Status System (Austin, Texas, U.S.A.)
AutoTech (Automated technical support) (Austin, Texas, U.S.A.)
Customer Technical Support
512 728-0685
512 728-0686
525 228-7870
525 228-7811
International Access Code: 95
Country Code: 52
Sales
City Code: 5
or toll free: 91-800-900-37
or toll free: 91-800-904-49
525 228-7878
525 228-7800
020 581 8838
Customer Service
Main
Netherlands (Amsterdam)
International Access Code: 00
Country Code: 31
Technical Support
Customer Care
020 581 8740
Home/Small Business Sales
Home/Small Business Sales Fax
Corporate Sales
toll free: 0800-0663
020 682 7171
City Code: 20
020 581 8818
Corporate Sales Fax
Fax
020 686 8003
020 686 8003
Switchboard
020 581 8818
Website: http://support.euro.dell.com
E-mail: [email protected]
Home and Small Business
Government and Business
Sales
New Zealand
0800 446 255
0800 444 617
0800 441 567
0800 441 566
671 16882
International Access Code: 00
Country Code: 64
Fax
Norway (Lysaker)
International Access Code: 095
Country Code: 47
Technical Support
Relational Customer Care
Home/Small Business Customer Care
Switchboard
671 17514
23162298
671 16800
Fax Technical Support (Upplands Vasby, Sweden)
Fax Switchboard
590 05 594
671 16865
Website: http://support.euro.dell.com
E-mail: [email protected]
Technical Support
Poland (Warsaw)
22 57 95 700
22 57 95 999
22 57 95 999
22 57 95 998
22 57 95 999
Customer Care
International Access Code: 011
Country Code: 48
Sales
Fax
City Code: 22
Switchboard
Website: http://support.euro.dell.com
E-mail: [email protected]
Technical Support
Portugal
35 800 834 077
Customer Care
34 902 118 540 or
35 800 834 075
International Access Code: 00
Country Code: 35
Sales
35 800 834 075
Fax
35 121 424 01 12
E-mail: [email protected]
Singapore (Singapore)
International Access Code: 005
Country Code: 65
Technical Support
toll free: 800 6011 051
604 633 4949
Customer Service (Penang, Malaysia)
Transaction Sales
toll free: 800 6011 054
toll free: 800 6011 053
011 709 7710
Corporate Sales
South Africa (Johannesburg)
International Access Code: 09/091
Country Code: 27
Technical Support
Customer Care
011 709 7707
Sales
011 709 7700
Fax
011 709 0495
City Code: 11
Switchboard
011 709 7700
Website: http://support.euro.dell.com
E-mail: [email protected]
Southeast Asian and Pacific
Countries
Customer Technical Support, Customer Service, and Sales (Penang, Malaysia)
604 633 4810
Spain (Madrid)
Home and Small Business
Technical Support
Customer Care
902 100 130
902 118 540
902 118 541
902 118 541
902 118 539
International Access Code: 00
Country Code: 34
City Code: 91
Sales
Switchboard
Fax
Website: http://support.euro.dell.com
E-mail: [email protected]
Corporate
Technical Support
902 100 130
Customer Care
902 118 546
91 722 92 00
91 722 95 83
Switchboard
Fax
Website: http://support.euro.dell.com
E-mail: [email protected]
Technical Support
Sweden (Upplands Vasby)
International Access Code: 009
Country Code: 46
08 590 05 199
08 590 05 642
08 587 70 527
08 590 05 594
08 590 05 185
Relational Customer Care
Home/Small Business Customer Care
Fax Technical Support
Sales
City Code: 8
Website: http://support.euro.dell.com
E-mail: [email protected]
Technical Support (Home and Small Business)
Technical Support (Corporate)
Customer Care
Switzerland (Geneva)
International Access Code: 00
Country Code: 41
0844 811 411
0844 822 844
0848 802 802
022 799 01 90
022 799 01 01
Fax
City Code: 22
Switchboard
Website: http://support.euro.dell.com
E-mail: [email protected]
Technical Support
Taiwan
toll free: 0080 60 1255
toll free: 0080 60 1256
toll free: 0080 651 228
Technical Support (Servers)
Transaction Sales
International Access Code: 002
Country Code: 886
or 0800 33 556
Corporate Sales
toll free: 0080 651 227
or 0800 33 555
Thailand
Technical Support
toll free: 0880 060 07
Customer Support (Penang, Malaysia)
Sales
604 633 4949
International Access Code: 001
toll free: 0880 060 09
Country Code: 66
U.K. (Bracknell)
Technical Support (Corporate/Preferred Accounts/PAD [1000+ employees])
Technical Support (Direct/PAD and General)
Global Accounts Customer Care
0870 908 0500
0870 908 0800
01344 723186
01344 723185
01344 723196
01344 723193
01344 723194
0870 907 4000
01344 860456
International Access Code: 010
Country Code: 44
Corporate Customer Care
City Code: 1344
Preferred Accounts (500-5000 employees) Customer Care
Central Government Customer Care
Local Government Customer Care
Home/Small Business Sales
Corporate/Public Sector Sales
Website: http://support.euro.dell.com
E-mail: [email protected]
U.S.A. (Austin, Texas)
International Access Code: 011
Country Code: 1
Automated Order-Status System
toll free: 1-800-433-9014
AutoTech (for portable and desktop computers)
Dell Home and Small Business Group (for portable and desktop computers):
Customer Technical Support (Return Material Authorization Numbers)
Customer Service (Credit Return Authorization Numbers)
toll free: 1-800-247-9362
toll free: 1-800-624-9896
toll free: 1-877-576-3355
toll free: 1-800-624-9897
National Accounts (systems purchased by established Dell national accounts [have your account number handy], medical
institutions, or value-added resellers [VARs]):
Customer Service and Technical Support (Return Material Authorization
toll free: 1-800-822-8965
Numbers)
Public Americas International (systems purchased by governmental agencies [local, state, or federal] or educational
institutions):
Customer Service and Technical Support (Return Material Authorization
Numbers)
toll free: 1-800-234-1490
Dell Sales
toll free: 1-800-289-3355
or toll free: 1-800-879-3355
toll free: 1-800-357-3355
toll free: 1-800-753-7201
toll free: 1-800-433-9005
toll free: 1-800-967-0765
toll free: 1-800-426-5150
toll free: 1-800-727-8320
toll free: 1-800-950-1329
toll free: 1-877-DELLTTY
Spare Parts Sales
DellWare™
Desktop and Portable Fee-Based Technical Support
Server Fee-Based Technical Support
Sales (Catalogs)
Fax
TechFax
Dell Services for the Deaf, Hard-of-Hearing, or Speech-Impaired
(1-877-335-5889)
512 338-4400
Switchboard
Dellnet Technical Support
toll free: 1-877-Dellnet
(1-877-335-5638)
Dell™ PowerEdge™ 2500 Systems Installation and Troubleshooting Guide
Notes, Notices, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
CAUTION: A CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
WARNING: A WARNING indicates a potentially hazardous situation which, if not avoided, may result in severe injury.
|
