DeLonghi EC 152 CD User Manual

Инструкция для  
Delonghi EC 152 CD  
ꢀꢁдꢊꢁбнꢈяꢄинфꢁꢊмꢈцияꢄꢁꢄтꢁвꢈꢊꢃ,  
ꢁтзывы,ꢄꢁбзꢁꢊыꢄиꢄꢈꢇꢆꢃꢆꢆꢂꢈꢊы  
ꢀꢁлꢂчитꢃꢄтꢃꢅничꢃꢆꢇꢂюꢄꢇꢁнꢆꢂльтꢈцию.  
ꢉꢊꢂглꢁꢆꢂтꢁчнꢁ.ꢄБꢃзꢄвыꢅꢁдныꢅ  
COFFEE MAKER  
Instruction for use  
Please retain instructions for  
future reference  
EC152.CD  
Electrical requirements  
Before using this appliance ensure that the voltage indicated on the product corresponds  
with the main voltage in your home, if you are in any doubt about your supply contact your  
local electricity company.  
The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13  
amp capacity.  
Should this plug not fit the socket outlets in your home, it should be cut off and replaced with  
a suitable plug, following the procedure outlined below.  
Note: Such a plug cannot be used for any other appliance and should therefore be properly  
disposed of and not left where children might find it and plug it into a supply socket - with  
the obvious consequent danger.  
Please note: We recommend the use of good quality plugs and wall sockets that can be  
switched off when the machine is not in use.  
IMPORTANT: The wires in the mains lead fitted to this appliance are coloured in accordance  
Green and Yellow to Earth  
with the following code:  
13 amp  
Fuse  
GREEN AND YELLOW  
BLUE  
BROWN  
EARTH  
NEUTRAL  
LIVE  
Brown to  
live  
Blue to  
neutral  
Cord Clamp  
As the colours of the wires in the mains lead of this appliance may not correspond with the  
coloured markings identifying the terminals in your plug, proceed as follows:  
-
-
-
The wire which is coloured green and yellow must be connected to the terminal in the plug which is  
marked with the letter E or by the earth symbol or coloured green or green and yellow.  
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or  
coloured black.  
The wire which is coloured brown must be connected to the terminal which is marked with the letter L  
or coloured red.  
When wiring the plug, ensure that all strands of wire are securely retained in each terminal.  
Do not forget to tighten the mains lead clamp on the plug. If your electricity supply point has  
only two pin socket outlets, or if you are in doubt, consult a qualified electrician.  
Should the mains lead ever require replacement, it is essential that this operation be carried  
out by a qualified electrician and should only be replaced with a flexible cord of the same  
size.  
After replacement of a fuse in the plug, the fuse cover must be refitted. If the fuse cover  
is lost, the plug must not be used until a replacement cover is obtained. The colour of the  
correct replacement fuse cover is that of the coloured insert in the base of the fuse recess or  
elsewhere on the plug. Always state this colour when ordering a replacement fuse cover.  
Only 13amp replacement fuses which are asta approved to B.S. 1362 should be fitted.  
This appliance conforms to the Norms EN 55014 regarding the suppression of radio inter-  
ference.  
Warning - this appliance must be earthed  
2
Description  
OFF  
position  
OK indicator light  
Steam  
position  
On indicator  
light  
Cofee- hot water  
delivery position  
Water tank  
Water tank lid  
Steam  
dial  
Filter compartment  
Power supply cable  
Cofee  
tamper  
Selector dial  
Steam or  
hot water tube  
Drip tray  
Cappuccino nozzle  
Boiler outlet  
Filter  
Filter holder  
Measure  
3
ig. 3  
ig. 2  
ig. 1  
1
2
ig. 5  
ig. 6  
ig. 4  
ig. 8  
ig. 9  
ig. 7  
ig. 11  
ig. 12  
ig. 10  
4
ig. 15  
ig. 14  
ig. 13  
ig. 17  
ig. 18  
ig. 16  
ig. 20  
ig. 21  
ig. 19  
ig. 22  
ig. 23  
ig. 24  
ig. 25  
ig. 26  
5
Safety  
Symbols used in these instructions  
The important recommendations have these symbols. These  
recommendations must be followed.  
to the enclosed guarantee lealet for details.  
Attention:  
Keep the packaging material (plastic bags, expanded  
polystyrene) out of the reach of children.  
Danger!  
Failure to comply can be or is the cause of injury due to  
life-threatening electric shocks.  
Attention:  
The appliance is not intended for use by persons  
(including children) with reduced physical, sensory or  
mental capabilities, or lack of experience and knowledge,  
unless they have been given supervision or instruction  
concerning use of the appliance by a person responsible  
for their safety. Children should be supervised to ensure  
that they do not play with the appliance.  
Attention!  
Failure to comply can be or is the cause of injury or  
damage to the appliance.  
Scalding hazard!  
Failure to comply can be or is the cause of scalding or  
burns.  
Scalding hazard!  
This appliance produces hot water and steam may form  
when it is operating.  
Please Note:  
This symbol highlights recommendations and important  
information for the user.  
Pay attention not to come into contact with hot water  
sprays or steam.  
Fundamental recommendations regarding safety  
Do not touch the cup warmer plate when the appliance  
is on; it is hot.  
Danger!  
As the appliance operates using electric current, electric  
shocks can not be excluded.  
Conditions of use  
This appliance is manufactured for the preparation of  
cofee and to heat beverages.  
Therefore, follow the safety recommendations given:  
Do not touch the appliance when you have wet  
hands or feet.  
The appliance is designed and produced for domestic use  
only. It is not suitable for use in:  
Do not touch the plug with wet hands.  
Make sure that the socket used can always be easily  
reached, so that the plug can be removed when  
required.  
staf kitchens in shops, oices and other workplaces  
farms  
hotels, motels or other holiday accommodation  
guest houses  
Remove the plug from the socket by acting directly  
on the plug itself. Do not pull the cable as damage  
could be caused.  
Any other use must be considered improper and therefore  
dangerous.  
Remove the plug from the socket to disconnect the  
appliance completely.  
The manufacturer is not liable for damage deriving from  
the improper use of the appliance.  
Do not attempt to repair the appliance if it should  
breakdown.  
Switch the appliance of, remove the plug from the  
socket and contact the After-Sales Service. Please  
refer to enclosed guarantee lealet for details.  
Iftheplugorpowersupplycablearedamaged,have  
them replaced exclusively by the De’Longhi After-  
Sales Service, in order to prevent risks. Please refer  
6
Introduction  
Instructions for use  
Only connect the appliance to a correctly installed socket  
with a minimum rating of 10A and correctly earthed.  
In the case of incompatibility between the socket and  
the plug on the appliance, have the plug replaced by a  
qualiied technician.  
Thank you for choosing this cofee machine. To get the  
very best out of your new cofee machine it is advisable  
to read these instructions before using the appliance.  
This is the only way to ensure optimum results and ma-  
ximum safety.  
The power supply cable on this appliance must  
never be replaced by the user as special tools are  
needed for this operation. Contact an After-Sales  
Centre authorised by the manufacturer if the cable  
is damaged or must be replaced, in order to avoid all  
risks. Please refer to enclosed guarantee lealet for  
details.  
The manufacturer is not liable for damage deriving from  
the failure to comply with the user instructions.  
Please Note:  
Keep these instructions carefully. If the appliance should  
be transferred to other persons, these instructions must  
accompany it.  
Filling the water tank  
1. Open the water tank lid (ig. 1) and then lift the tank  
to remove it (ig. 2).  
Check after transport  
After the packaging has been removed, check the  
integrity of the appliance and the presence of all  
accessories.  
2. Fill the tank with fresh water but do not pass MAX  
level (ig. 3). Re-position the tank by pressing it  
lightly in a way to open the valve situated on the  
base of the tank itself.  
Do not use the appliance in the presence of obvious  
damage. Contact the De’Longhi Customer Services  
department, please see enclosed lealet.  
3. Alternatively, do not remove the tank, just ill it by  
pouring in water from a jug, be careful of splashes  
Installing the appliance  
Attention!  
The following safety measures must be complied with  
when installing the appliance:  
Attention!  
Do not operate the appliance without water in the tank  
and always ill it when the water is a few centimetres  
from the bottom.  
Theappliancecouldbedamagedbythepenetration  
of water.  
Please Note: it is normal to ind water in the  
compartment under the tank; dry using a clean sponge.  
Do not position the appliance near to water taps or  
sinks.  
The appliance could be damaged if the water it  
contains freezes. Do not install the appliance in a  
room where the temperature can fall below freezing  
point.  
Position the power supply cable in a way that it  
cannot be damaged by sharp edges or by contact  
with hot surfaces.  
Connecting the appliance  
Attention!  
Make sure that the electric mains voltage corresponds  
with that indicated on the rating plate on the base of the  
appliance.  
7
Making espresso  
Making espresso  
Please Note: irst use  
cofee can run out slowly. If you press too lightly, the  
cofee can run out too fast.  
3. Remove any excess cofee from the rim of the ilter-  
holder and attach it to the machine: turning it fully  
home to the right (ig. 5) to prevent water from  
escaping.  
Before using the appliance for the irst time, rinse the  
internal piping thoroughly, operating it as you would  
to make cofee, until two tanks of water have emptied,  
then proceed with making cofee.  
4. Position the cup or cups under the ilter-holder  
spouts (ig. 11). It is recommended to warm the  
cups before making the cofee by running them  
under hot water.  
Pre-heating the cofee machine  
1. Turn the appliance on by rotating the selector dial  
to the  
position (the relative indicator light  
switches on) (ig. 4) and attach the ilter-holder  
with the empty ilter to the machine (ig. 5). Make  
sure that the ilter holder is correctly inserted into  
the relative seat (ig. 6).  
5. Make sure that the OK light (ig. 7) is on (if it is of,  
wait for it to switch on) and turn the selector dial to  
the  
of cofee has been obtained, interrupt delivery by  
rotating the selector dial back to the position  
position (ig. 8). Once the desired amount  
2. Place a cup under the ilter-holder. Use the same  
cup in which the cofee is to be served so that it can  
be pre-heated.  
(ig. 7). (It is recommended not to run the cofee for  
more than 45 seconds).  
3. Wait until the OK light comes on (ig. 7) then  
immediately rotate the selector dial to the  
position (ig. 8), allow the water to run until the OK  
light switches of , then stop the water by rotating  
the selector dial back to the position (ig. 4) and  
empty the cup.  
6. Turn the ilter holder from right to left to release the  
ilter-holder.  
Scalding hazard!  
To prevent sprays, do not release the ilter-holder while  
the machine is dispensing cofee.  
(It is normal for a small, harmless puf of steam to be  
released when the ilter-holder is removed).  
7. To remove the used cofee, lock the ilter using  
the lever in the grip and let the cofee fall out by  
knocking the over-turned ilter-holder (ig. 12).  
8. To turn the appliance of, rotate the selector dial to  
the “ ”position.  
Making and espresso using ground cofee  
1. To prepare one cofee, ill the ilter with a level  
measuring spoon of ground cofee, about 7gr. (ig.  
9). If you wish to prepare two cups of cofee, ill the  
ilter with two less-than-level measuring spoons  
of ground cofee (about 7+7 gr). Fill the ilter  
with small amounts at a time to prevent the cofee  
spilling out.  
Attention:  
For correct use, before illing the ilter with ground cofee  
always make sure there is no residual cofee in the ilter  
from the previous infusion.  
2. Distribute the ground cofee evenly and press it  
lightly using the cofee tamper (ig. 10).  
Pressing the ground cofee is very important to  
obtain a good espresso. If you press too hard, the  
8
Cappuccino  
To switch of the appliance, turn the selector dial to  
the position.  
Making a cappuccino  
1. Prepare the espresso cofee as described in the  
previous paragraphs, using cups that are large  
enough  
9. Pour the frothed milk into the cups containing the  
previously prepared espresso cofee. The cappuccino  
is ready. Add sugar and sprinkle a little powder  
chocolate on top of the froth if desired.  
2. Rotate the selector dial to the position (ig. 13).  
3. While waiting for the OK light, ill a container with  
about 100 grams of milk for every cappuccino  
to be prepared. The milk must be at refrigerator  
temperature (5°C). When choosing the container  
consider that the volume of the milk will increase by  
2 or 3 times.  
Please Note:  
If more than one cappuccino is to be prepared, irst  
make all of the cofees and then prepare the milk for  
all of the cappuccinos;  
If more cofee must be prepared after the  
milk has been frothed, allow the boiler to  
cool irst otherwise the cofee may be burned.  
To cool it, position a container under the ilter-holder  
spouts, turn the selector dial to the position (ig.  
8); allow water to run out until the steam function  
light switches of; turn the selector dial to the  
position and prepare cofee as illustrated before.  
Maximum steam delivery of 60 seconds is  
recommended and the milk must not be frothed  
more than 3 times consecutively.  
Please Note:  
It is recommended to use semi-skimmed milk at  
refrigerator temperature.  
4. Position the container with the milk under the  
cappuccino nozzle.  
5. Wait for the OK light to switch on. This indicates  
that the boiler has reached the ideal temperature  
for steam production, when reaching the ideal  
temperature, it is normal for a small puf of steam  
and water to be released, and collected in the drip  
tray.  
Cleaning the Cappuccino nozzle  
6. Extract the cappuccino nozzle by pulling it and  
rotating it towards the left (ig. 14): pay attention  
not to touch the boiler outlet because it is hot.  
Position the container with the milk under the  
cappuccino nozzle.  
The cappuccino nozzle must always be washed after  
each use to ensure hygiene. Proceed as follows:  
1. Discharge a small amount of steam for a few seconds  
(see points 2,5 and 6 of the previous paragraph) by  
turning the steam dial (ig. 16). By doing this, the  
cappuccino nozzle clears any milk left inside. Switch  
the appliance of by turning the selector dial in  
position.  
7. Dip the cappuccino nozzle into the milk a few  
millimeters (ig. 15). Turn the steam dial anti-  
clockwise (ig. 16), for at least half a turn. Steam  
escapes from the cappuccino nozzle giving the milk  
a creamy appearance and increasing its volume. To  
obtain a creamier froth, dip the cappuccino nozzle  
into the milk and turn the container with slow  
movements from the bottom upwards.  
2. Use one hand to hold the cappuccino tube and the  
other to release the cappuccino nozzle by turning it  
clockwise (ig. 19).  
3. Wash the cappuccino nozzle thoroughly in warm  
water.  
8. When the volume of the milk has doubled, dip the  
cappuccino nozzle deep down and continue to heat  
the milk (ig. 17). When the desired temperature  
(ideal value is 60°C) and the desired milk froth have  
been reached, interrupt the steam by turning the  
steam dial clockwise (ig. 18) and turn the selector  
dial to the position.  
4. Makesurethattheholesindicatedbythearrows(ig.  
20) are not blocked. Clean using a pin if necessary.  
5. Re-mount the steam maker by inserting it irmly  
upwards into the steam tube.  
6. Re-mount the cappuccino nozzle by inserting it  
upwards and turning it anti-clockwise.  
9
Hot water • Cleaning  
Producing hot water  
ilter (ig. 25), making sure that the pin is inserted  
into the hole of the support itself (see arrow ig.  
25).  
1. Switch the machine on by turning the selector dial  
to the position (the relative light comes on) (ig.  
4). Wait for the OK light to switch on (ig. 7).  
2. Position a container under the cappuccino nozzle.  
3. When the OK light comes on, turn the selector dial  
Finally, tighten the tap.  
The warranty is not valid if the cleaning operations  
described above are not performed on a regular basis.  
to the  
position (ig. 8) and turn the steam dial  
Cleaning the boiler outlet  
About every 300 cofees the espresso boiler outlet must  
be cleaned as follows:  
anti-clockwise at the same time (ig. 16). The hot  
water will be delivered from the cappuccino nozzle.  
4. To interrupt the hot water, turn the steam dial  
clockwise and turn the selector dial to the  
position.  
Make sure that the cofee machine is not hot and  
the plug is disconnected from the socket;  
Use a screwdriver to remove the screw that ixes the  
espresso boiler outlet (ig. 26);  
Maximum delivery of 60 seconds is recommended.  
Remove the boiler outlet;  
Clean the boiler using a damp cloth;  
Cleaning  
Danger!  
During cleaning, never immerse the cofee machine  
in water. It is an electrical appliance.  
Clean the outlet thoroughly using hot water and a  
brush. Check that the holes are not blocked. If this is  
not the case, clean them using a pin (ig. 23).  
Re-mount the boiler outlet, paying attention to  
position it correctly on the gasket.  
Before performing any cleaning operations on the  
external parts of the appliance, switch the machine  
of, remove the plug from the socket and let the  
machine cool down.  
The warranty is not valid if the cleaning operations  
described above are not performed on a regular basis.  
Cleaning and maintenance of the ilter  
Other cleaning operations  
1. Do not use solvents or abrasive detergents to clean  
the machine. Use a soft, damp cloth.  
Clean the ilter-holder and ground cofee ilter about  
every 300 cofees or if the cofee drips through the ilter-  
holder and does not low unrestricted:  
2. Clean the ilter-holder cup, the ilters, drip tray and  
water tank regularly.  
Remove the ilter from the ilter-holder.  
Unscrew the ilter cap (ig. 21) in the direction  
indicated by the arrow on the cap itself.  
To empty the drip tray, remove the cup warmer grid,  
remove the water and clean the tray using a cloth:  
then re-assemble the drip tray.  
Slide the cream enhancer device from the container  
by pushing it from the cap end.  
Remove the gasket.  
Rinse all components and clean the metal ilter  
thoroughly using hot water and a brush (ig. 22).  
Check that the holes in the metal ilter are not  
blocked. If this is not the case, clean them using a  
pin (see ig. 23) or when descaling.  
Clean the water tank using a soft bottle-brush in  
order to reach the bottom.  
Danger!  
During cleaning, never immerse the machine in water: it  
is an electric appliance.  
Re-mount the ilter and the gasket on the plastic  
disc as indicated in (ig. 24). Make sure that the  
plastic disc pin is inserted inside the hole in the  
gasket as indicated by the arrow in (ig. 24).  
Re-insert the unit into the steel container for the  
10  
Descaling · Disposal  
which it is made in order to make signiicant savings in energy  
and resources.  
Descaling  
It is recommended to descale the machine about every  
200 cofees.  
Follow this procedure:  
The product has the crossed-out wheeled bin mark as a  
reminder of the obligation to dispose of household appliances  
separately.  
1. Fill the tank with the descaling solution obtained  
by diluting the descaler with water following the  
indications given on the pack.  
The appliance is in compliance with the following  
CE Directives:  
2. Switch the appliance on by turning the selector to  
the position and wait until the OK indicator light  
comes on.  
“LowvoltageDirective”2006/95/CEandsuc¬cessive  
amendments.  
“EMC Directive” EMC 2004/108/CE and suc¬cessive  
amendments.  
3. Make sure that the ilter holder is not attached and  
position a suitable container under the machine  
outlet.  
The materials and objects destined to come into  
contact with food stufs are in compliance with the  
provisions of the 1935/2004 European Standard.  
4. Rotate the selector dial to the  
position and  
allow about 1/4 of the solution contained in the  
tank low out. Every now and again turn the steam  
dial and allow a small amount of solution to escape;  
then interrupt by turning the selector dial to the  
position then interrupt by pressing the button again  
and leave the solution to act for about 5 minutes.  
5. Repeat point 4 another 3 times or until the tank is  
completely empty.  
Technical date  
Mains voltage:  
Absorbed power:  
Dimensions (LxHxD ):  
Pressure:  
220-240V 50/60Hz  
1100W  
195x285x240 (330) mm  
˜
15 bar  
1 L  
Water tank capacity:  
Cable lenght:  
Weight:  
1,2 m  
3 kg  
6. To eliminate residues of the descaling solution, rinse  
the tank well and ill it with clean water (without  
descaler).  
7. Rotate the selector dial to the  
position and  
operate the appliance until the tank is completely  
empty.  
8. Repeat operations 6 and 7 again.  
Repairs to the cofee machine relative to lime scale  
problems are not covered by the warranty if the descaling  
procedure is not performed on a regular basis.  
Disposal  
Recommendations for the correct disposal of  
the product in compliance with the 2002/96/CE  
European Directive.  
The product must not be disposed of as urban waste at the end  
of its working life.  
It must be taken to appropriate local authority separate waste  
collection centres or to dealers providing this service.  
Disposing of a household appliance separately avoids possible  
negativeconsequencesfortheenvironmentandhealthderiving  
from unsuitable disposal and allows to recover the materials of  
11  
Troubleshooting  
Problem  
Possible causes  
Solution  
No water in the tank  
Fill the water tank  
Espresso cofee does not low out  
The holes in the ilter-holder are blocked  
Clean the holes in the ilter-holder spouts  
The espresso boiler outlet is blocked  
Clean as indicated in the “Cleaning the boiler outlet”  
paragraph  
The ilter-holder is inserted incorrectly  
Attach the ilter-holder correctly and turn it fully  
to the right  
Espresso cofee drips from the edges of  
the ilter-holder instead of through the  
holes  
The espresso boiler gasket has lost elasticity  
The holes in the ilter-holder spout are blocked  
Replace the espresso boiler gasket: contact Customer  
Services  
Clean the holes in the spouts.  
The espresso OK light is not on when the cofee  
button is pressed  
Wait for the OK light to switch on  
The espresso cofee is cold  
Pre-heating has not been carried out  
The cups have not been pre-heated  
Pre-heat as indicated in the paragraph  
Pre-heat the cups using hot water or leaving them  
for at least 20 minutes on the cup warmer plate  
on the lid  
The water tank is empty  
Fill the water tank  
Loud pump noise  
The tank is inserted incorrectly and the valve on the  
bottom is not open  
Press the tank lightly to open the valve on the  
bottom  
The ground cofee has not been suiciently pressed  
Not enough ground cofee  
Tamper the ground cofee more (ig. 10)  
The cofee cream is light (cofee lows  
quickly from the spout)  
Increase the amount of ground cofee  
The cofee is not ground inely enough  
Only use cofee ground speciically for espresso  
cofee machines  
Incorrect type of ground cofee  
The ground cofee is too tightly pressed  
Too much ground cofee  
Change the quality of the ground cofee  
Decrease the amount of ground cofee  
Reduce the quantity of ground cofee  
Clean as indicated in “Cleaning the ilter”  
The cofee cream is dark (the cofee  
lows slowly from the spout)  
The espresso boiler outlet is blocked  
The ilter is blocked  
Only use cofee ground speciically for espresso cofee  
machines and it must not be damp  
The cofee is too inely ground  
The ground cofee is too ine or is damp  
Incorrect type of ground cofee  
Milk not cold enough  
Change the quality of the ground cofee powder  
Only use cofee ground speciically for espresso cofee  
machines and it must not be damp  
Change the quality of the ground cofee powder  
Always use milk at refrigerator temperature  
The milk does not froth when making a  
cappuccino  
Cappucccino maker is dirty  
Carefully clean the holes in the cappuccino nozzle, in  
particular, those indicated in igure 20  
12  

Motorola MILESTONE XT800 User Manual
Magnavox AJ3282 User Manual
Kenwood KDC M4524G User Manual
Kalorik Team International Group Coffeemaker CM 38933 User Manual
Hitachi Travelstar HTS725016A9A360 User Manual
Fetco Home Decor Coffeemaker CBS 2032E User Manual
Black Box Computer Accessories KV1402A User Manual
Blackberry ICQ User Manual
Audiovox CDM 8900 User Manual
Apple PCIe Fan User Manual