5713216051/02.11
C1
B
C
B1
C2
B2
B3
B6
B7
C3
B4
B5
B8
B9
C4
C5
B10
D
D1
D2
D3
D4
2
A
A4
A5
A2
A3
A6
A7
A8
A1
A9
A10
A12
A19
C4
PUSH
A13
A11
A15
A14
A17
A16
A18
3
1
2
3A
3B
4
5
6
7
11
15
8
9
10
12
13
14
16
4
17
18
19
23
27
20
21
24
CLEAN
22
26
25A
25B
A
B
SH
U
P
H
S
U
P
B
28
A
29
30
31A
31B
5
makinG Drinks With milk ................. 14
Filling and attaching the milk container.............14
Making cappuccino or macchiato ....................14
Making frothed milk (without coffee)................15
Preparing milk (unfrothed and without coffee) .15
Cleaning the milk frother with the CLEAN
contents
important safeGuarDs......................7
SAVE THESE INSTRUCTIONS ............................7
short corD instructions ..................7
button .............................................................15
Programming the quantity of coffee and milk in
the cup for cappuccino or milk .........................15
introDuction ...................................8
Symbols used in these instructions....................8
Letters in brackets ..............................................8
Troubleshooting and repairs ...............................8
Description .........................................................8
Description of the appliance ...............................8
Description of the control panel..........................8
Description of the accessories............................9
Description of milk container..............................9
heatinG Water ................................ 15
Change the quantity of water delivered
automatically. ...................................................15
cleaninG........................................ 16
Cleaning the coffee grounds container..............16
Cleaning the drip tray and condensate tray.......16
Cleaning the inside of the coffee maker ............16
Cleaning the water tank.....................................16
Cleaning the coffee spouts................................17
Cleaning the pre-ground coffee funnel..............17
Cleaning the infuser..........................................17
Cleaning the milk container...............................17
Cleaning the hot water/steam nozzle.................18
preliminary checks ..........................9
Checking the appliance .......................................9
Installing the appliance .......................................9
Connecting the appliance....................................9
Using the appliance for the first time..................9
turninG the appliance on ................ 10
turninG the appliance off .............. 10
Descale ......................................... 18
menu settinGs................................ 10
Descale .............................................................10
Adjust time........................................................10
Auto-off.............................................................10
Auto-start..........................................................11
Setting the temperature ....................................11
Energy Saving...................................................11
Setting water hardness .....................................11
Setting the language ........................................11
Install filter........................................................11
Replacing the filter............................................11
Activate/deactivate the beep..............................11
Cup lighting ......................................................12
Default values (reset)........................................12
Statistics function.............................................12
settinG Water harDness.................. 19
Measuring water hardness................................19
Set water hardness ...........................................19
Water softener filter..................... 19
Installing the filter.............................................19
Replacing the filter............................................19
Removing the filter ...........................................20
technical specification................... 20
DisplayeD messaGes........................ 21
trouBleshootinG............................ 22
limiteD Warranty........................... 24
makinG coffee ................................ 12
Selecting the coffee taste..................................12
Selecting the quantity of coffee in the cup .......12
Customising the “my coffee” quantity ..............12
Adjusting the coffee mill ...................................13
Tips for a hotter coffee......................................13
Making coffee using coffee beans.....................13
Making coffee using pre-ground coffee ............14
6
en
i m p o r t a n t s a f e G u a r D s
When using electrical appliances, basic safety precautions should always be followed, inclu-
ding the following.
•
•
Read all instructions carefully.
Make sure the voltage of your electrical system corresponds to the voltage shown on the
bottom of the machine.
•
•
Do not touch hot surfaces. Use handles or knobs.
To protect against fire, electrical shock and personal injury, do not immerse cord, plug or
appliance in water or other liquid.
•
Keep the appliance out of the reach of children and do not leave appliance unattended
while in operation.
•
•
Unplug from the outlet when not in use and before cleaning.
Do not operate with a damaged cord or plug, or after the appliance malfunctions, or has
been damaged in any manner. Return the appliance to the nearest authorized service
facility for examination, repair or adjustment.
The use of accessory attachments not recommended by the manufacturer may result in
fire, electrical shock, or personal injury.
Do not use outdoors.
•
•
•
Make sure the power cord does not hang over the edge of the table or counter-top to avoid
getting accidentally caught or entangled.
•
•
•
Do not place the appliance or its electrical parts on or near electric stoves, cooking surfa-
ces, or gas burners.
Plug cord into the wall outlet. To disconnect, first turn machine “off”, then remove plug
from wall outlet.
Do not use the appliance for other than the intended use. This appliance is to be utilized
for domestic use only. The manufacturer declines all responsibility for any damage caused
by improper, incorrect, or irresponsible use.
WarninG: to reduce the risk of fire or electric shock, do not remove the cover or the exterior of the
unit. Don’t attempt to repair or modify the machine, doing so will void the warranty. repair should
be done by authorized service personnel only!
saVe these instructions
THIS APPLIANCE IS FOR HOUSEHOLD USE ONLY
short corD instructions
A short power cord is provided to reduce risks resulting from becoming entangled in or tripping
over a longer cord.
Longer, detachable power supply cords or extension cords are available and may be used if care is
exercised in their use.
If an extension cord is used, the marked electrical rating should be at least as great as the electrical
rating of the appliance. If the appliance is provided with 3- wire, grounding type cord, the extension
should be a GROUNDING TYPE 3 - WIRE CORD. The longer cord should be arranged so that it will
not drape over the counter-top or table top where it can be pulled on by children or tripped over.
Your product is equipped with a polarized alternating current line plug (a plug having one blade
wider than the other). This plug will fit into the power outlet only one way. This is a safety feature.
If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still
fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose
of the polarized plug.
-
-
-
7
introDuction
Description
Thank you for choosing the ECAM23.450 SL
automatic coffee and cappuccino maker.
We hope you enjoy using your new appliance.
Take a few minutes to read these instructions.
This will avoid all risks and damage to the
machine.
Description of the appliance
(page 3 - A )
A1. Control panel
A2. Grinding adjustment knob
A3. Cup shelf
A4. Beans container lid
A5. Pre-ground coffee funnel lid
A6. Pre-ground coffee funnel
A7. Beans container
A8. Main switch
symbols used in these instructions
Important warnings are identified by these
symbols.
These warnings must absolutely be respected.
A9. Water tank
A10. Infuser-extraction door
A11. Infuser
A12. Hot water/steam nozzle
A13. Coffee spout (adjustable height)
A14. Coffee grounds container
A15. Condensate tray
A16. Cup tray
A17. Drip tray water level indicator
A18. Drip tray
A19. Cup lighting
Danger!
Failure to observe the warning could result in
possibly life threatening injury from electric
shock.
Important!
Failure to observe the warning could result in
injury or damage to the appliance.
Danger of burns!
Failure to observe the warning could result in
scalds.
Description of the control panel
(page 2 - B )
A number of buttons on the panel have a double
function. This is indicated in brackets in the
description.
B1. Display: guides the user in using the
appliance
B2. Selection knob: turn to select the required
quantity of coffee. (When in the settings
MENU, turn to select the required function).
Please note :
This symbol identifies important advice or
information for the user.
letters in brackets
The letters in brackets refer to the legend in the
Description of the Appliance on page 2-3.
B3.
button: turns the appliance on and off.
troubleshooting and repairs
B4. p button to access the menu
B5.
In the event of problems, first try and resolve
them following the information given in the
section “Displayed messages” on page 21 and
“Troubleshooting” on page 22.
If this does not resolve the problem or you
require further information, you should consult
Customer Services by calling the number given
on the annexed “Customer Service” sheet.
If your country is not among those listed on the
sheet, call the number given in the guarantee.
If repairs are required, contact De’Longhi
Customer Services only.
button: to perform a rinse cycle.
(When in the settings MENU, it acts as
the “ESC” button to exit from the selected
function and go back to the main menu).
aroma selection button: to select the
coffee taste.
button: to make 1 cup of coffee with the
settings displayed.
button: to make 2 cups of coffee with
the settings displayed.
button: to deliver hot water.
(When you access the MENU: “OK” button to
confirm the selection made)
B6.
B7.
B8.
B9.
The addresses are given in the guarantee
certificate provided with the appliance.
B10.CAPPUCCINO button: to prepare cappuccino
or frothed milk.
8
Description of the accessories
(page 2 - C )
C1. Measuring scoop for pre-ground coffee
C2. Cleaning brush
C3. Descaler bottle
C4. Water softener filter (certain models only)
C5. Hot water spout
Connect the appliance to an efficiently earthed
and correctly installed socket with a minimum
current rating of 10A only.
If the power socket does not match the plug on
the appliance, have the socket replaced with a
suitable type by a qualified professional.
en
using the appliance for the first time
Description of milk container
(page 2 - D )
D1. Froth adjustment knob
D2. Frothed milk spout (adjustable)
D3. Milk intake tube
Please note!
•
•
Coffee has been used to factory test the
appliance and it is therefore completely
normal for there to be traces of coffee in the
mill. The machine is, however, guaranteed to
be new.
D4. CLEAN button
preliminary checks
checking the appliance
After removing the packaging, make sure the
product is complete and undamaged and that all
accessories are present.
You should customize water hardness as
soon as possible following the instructions
in the section “Setting water hardness” on
page 19.
Do not use the appliance if it is visibly damaged.
Contact De’Longhi Customer Services.
1. Plug the appliance into the electrical socket
and press the main switch on the back of the
appliance (fig. 1).
You must first choose the language (the
languages scroll through at intervals of about 3
seconds).
2. When “English” appears, press the
button (fig. 2) for a few seconds until
“ENGLISH installed” is displayed.
Follow the instructions displayed by the
appliance:
3. “FILL TANK!”: remove the water tank, fill to
the MAX line with fresh water (fig. 3A) then
replace in the appliance (fig. 3B).
4. “INSERT WATER SPOUT!”: Check that the
hot water spout is inserted on the nozzle and
place a container with a minimum capacity of
3.4 oz / 100 ml underneath (fig. 4).
installing the appliance
Important!
When installing the appliance, respect the
following safety warnings:
•
The appliance could be damaged if the
water it contains freezes. Do not install the
appliance in a room where the temperature
could drop below freezing point.
•
The appliance gives off heat.
After positioning the appliance on the
worktop, leave a space of at least 1.18 in/
3 cm between the surfaces of the appliance
and the side and rear walls and at least 5.9
in/ 15 cm above the coffee maker.
•
•
Water penetrating the coffee maker could
cause damage. Do not place the appliance
near water taps or sinks.
Arrange the power cable in such a way that
it cannot be damaged by sharp edges or in
contact with hot surfaces (e.g. electric hot
plates).
5. “Hot water... Confirm?” is displayed;
6. Press the
button to confirm. The
appliance delivers water from the spout then
goes off automatically.
The coffee maker is now ready for normal use.
Please note!
connecting the appliance
•
•
When using the appliance for the first time,
you need to make 4-5 cups of coffee or 4-5
cappuccinos before the appliance starts to
give satisfactory results.
Important!
Check that the mains power supply voltage
corresponds to the value indicated on the rating
plate on the bottom of the appliance.
When making the first 5-6 cappuccinos, it
9
is normal to hear the noise of boiling water.
After this, the noise diminishes.
To enjoy your coffee even more and improve
the performance of your appliance, we
displayed and the appliance goes off.
Please note!
If the appliance is not used for an extended
period, also release the main switch (fig. 1).
•
recommend installing
a
water softener
filter as described in the section “WATER
SOFTENER FILTER” (pg. 19). If your model
is not provided with a filter, you can request
one from De’Longhi Customer Services.
Important!
To avoid damaging the appliance, never release
the main switch (fig. 1) while the appliance is
on.
turninG the appliance on
menu settinGs
When you access the programming menu by pressing
the p button, the following menu items are available:
Please note!
Before turning the appliance on, press the main
switch on the back of the appliance (fig. 1).
Descale
Each time the appliance is turned on, it performs
an automatic preheat and rinse cycle which
cannot be interrupted. The appliance is ready for
use only after completion of this cycle.
For instructions on descaling, see page 18.
adjust time
To adjust the time on the display, proceed as
follows:
1. Press the p button to enter the menu;
2. Turn the selection knob (fig. 7) until “Adjust
time” is displayed;
Danger of burns!
During rinsing, a little hot water comes out of
the coffee spouts and is collected in the drip
tray underneath. Avoid contact with splashes of
water.
3. Press the
button (fig. 2);
4. Turn the selection knob (fig. 7) to change the
hours;
•
To turn the appliance on, press the
5. Press the
button to confirm;
6. Turn the selection knob (fig. 7) to change the
minutes;
button (fig. 5). The message “Heating
up... Please wait” is displayed.
After heating, the message “Rinsing...” is
displayed. As well as heating the boiler, the
appliance also heats the internal circuits by
circulating hot water.
The appliance is at temperature when a message
indicating the coffee taste and quantity is
displayed.
7. Press the
button to confirm.
This sets the time. Press the
the menu.
button to exit
auto-off
The appliance is set to turn off automatically if
not used for 2 hours.
The time can be changed so that the appliance
switches off after 15 or 30 minutes, or after 1,
2 or 3 hours.
To re-program Auto-off, proceed as follows:
1. Press the p button to enter the menu;
2. Turn the selection knob (fig. 7) until “Auto-
off” is displayed;
turninG the appliance off
Each time the appliance is turned off, it performs
an automatic rinse cycle which cannot be
interrupted.
Danger of burns!
During rinsing, a little hot water flows from the
coffee spouts.
3. Press the
button;
4. Turn the selection knob (fig. 7) until the
desired operation time is displayed (15 or 30
minutes, or 1, 2 or 3 hours);
Avoid contact with splashes of water.
5. Press the
6. Press the
Auto-off is programmed.
button to confirm;
button to exit the menu.
To turn the appliance off, press the
(fig. 5). The appliance performs a rinse cycle,
then the message “Turning Off Please wait...” is
button
10
auto-start
When energy saving mode is active, an asterisk
appears below “Energy Saving” in the menu.
To deactivate or activate “Energy Saving” mode,
proceed as follows:
1. Press the p button to enter the menu;
2. Turn the selection knob (fig. 7) until “Energy
Saving” is displayed;
en
You can set the auto-start time in order to
have the appliance ready at a certain time (for
example in the morning) so you can make coffee
immediately.
Please note!
To activate this function, the time must already
have been set correctly.
3. Press the
button. “Deactivate?” is
displayed, or “Active?” if the function has
already been disabled.
To activate Auto-on, proceed as follows:
1. Press the p button to enter the menu;
2. Turn the selection knob (fig. 7) until “Auto-
start” is displayed;
3. Press the
displayed;
4. Press the
5. Turn the selection knob to choose the hours;
6. Press the button to confirm;
4. Press the
button to deactivate energy
saving mode;
5. Then press the
menu.
button to exit the
button. “Activate?” is
When the function is active, if the machine is
not used for about 1 minute, “Energy Saving” is
displayed.
button to confirm;
Please note!
7. Turn the selection knob (fig. 7) to change the
minutes;
8. Press the
When in energy saving mode, a few seconds
may elapse before the first coffee is delivered as
the appliance must heat up again.
button to confirm;
button to exit the menu.
9. Press the
Once the time has been confirmed, activation
of auto-start is indicated by the symbol
displayed alongside the time and under the Auto-
start item in the menu.
setting water hardness
For instructions on setting water hardness, see
page 19.
To deactivate the function:
1. Select auto-start from the menu;
setting the language
To change the language for the display, proceed
as follows:
1. Press the p button to enter the menu;
2. Turn the selection knob (fig. 7) until “Set
language” is displayed;
2. Press the
displayed;
3. press the
button. “Deactivate?” is
button to confirm.
The
symbol is no longer displayed.
3. Press the
4. Turn the selection knob until the required
language is displayed;
5. Press the
6. Press the
button;
setting the temperature
To modify the temperature of the water used to
make the coffee, proceed as follows:
1. Press the p button to enter the menu;
2. Turn the selection knob (fig. 7) until “Set
temperature” is displayed;
button to confirm;
button to exit the menu.
install filter
3. Press the
button;
For instructions on how to install the filter, see
the section “Installing the filter” on page 19.
4. Turn the selection knob until the required
temperature (l = low; llll = high) is
displayed;
replacing the filter
For instructions on how to replace the filter, see
the section “Replacing the filter” on page 19.
5. Press the
button to confirm;
6. Press the
button to exit the menu.
energy saving
activate/deactivate the beep
Use this function to activate or deactivate energy
saving mode. When activated, the function
reduces energy consumption.
This activates or deactivates the beep emitted by
the machine each time the buttons are pressed
or an accessory is inserted/removed.
11
The beep is active by default.
To deactivate or reactivate the beep, proceed as
follows:
1. Press the p button to enter the menu;
2. Turn the selection knob (fig. 7) until “Beep”
is displayed;
“Statistics” is displayed;
3. Press the
button;
4. Turn the selection knob (fig. 7) to verify:
-
-
how many coffees have been made;
how many times the machine has been
descaled;
3. Press the
“Activate?” is displayed;
4. Press the
button. “Deactivate?” or
-
-
-
the total number of litres of water delivered;
how many cappuccinos have been made;
how many times the water softener filter has
been replaced.
button to activate or deactivate
the beep (or the
button to exit);
5. Activation of the beep is indicated by an
asterisk after the “Beep” item in the menu.
5. Press the
menu.
button twice to exit the
Press the
button to exit the menu.
makinG coffee
cup lighting
selecting the coffee taste
The appliance is set by default to make coffee
with a standard taste.
You can also choose one of these tastes:
Extra-mild taste
Mild taste
Standard taste
This function activates or deactivates the cup
lighting. The lighting is activated by default.
Thelightscomeoneachtimecoffeeorcappuccino
is made and during each rinse cycle.
To deactivate or reactivate this function, proceed
as follows:
1. Press the p button to enter the menu;
2. Turn the selection knob (fig. 7) until “Cup
lighting” is displayed.
Strong taste
Extra-strong taste
3. Press the
“Activate?” is displayed;
4. Press the
button. “Deactivate?” or
To change the taste, press the
(fig. 6) repeatedly until the required taste is
displayed.
button
button to activate or deactivate
the cup lighting (or the
button to exit);
5. When the function is active, an asterisk
appears after “Cup lighting” in the menu.
selecting the quantity of coffee in the cup
The appliance is set by default to make a standard
quantity of coffee.
Press the
button to exit the menu.
To select the quantity of coffee, turn the selection
knob (fig. 7) until the message corresponding to
the required quantity of coffee is displayed:
Default values (reset)
This resets all menu settings and programmed
quantities back to the default values (with the
exception of the language which remains as set
previously).
quantity in cup
coffee selected
(fl oz./ ml)
To reset the default values, proceed as follows:
1. Press the p button to enter the menu;
2. Turn the selection knob (fig. 7) until “Default
values” is displayed;
MY COFFEE
Programmable:
from ≃0.68/20 to
≃6/180
ESPRESSO
STANDARD
LONG
≃1.35/40
≃2/60
≃3/90
3. Press the
button;
4. The message “Confirm?” is displayed.
5. Press the
button to confirm and exit.
statistics function
This displays statistics relating to the machine.
EXTRA LONG
≃4/120
To display, proceed as follows:
1. Press the p button to enter the menu;
2. Turn the selection knob (fig. 7) until
customizing the “my coffee” quantity
The appliance is set by default to automatically
deliver 1 fl oz./ 30 ml of “my coffee”.
12
To modify this quantity, proceed as follows:
1. Place a cup under the coffee spouts (fig.
11).
2. Turn the selection knob until “MY COFFEE” is
displayed.
•
•
warm the cups with hot water (using the hot
water function);
select the “high” coffee temperature in the
menu.
en
making coffee using coffee beans
3. Keep the
button (fig. 8) pressed until the
message “1 MY COFFEE Program quantity”
is displayed and coffee delivery begins.
Release the button.
Important!
Do not use caramelized or candied coffee beans
as this could damage the appliance.
4. As soon as the coffee in the cup reaches the
required level, press the button
again.
The quantity of coffee in the cup has now been
programmed.
(fig. 8)
1. Fill the container with coffee beans (fig. 10).
2. Place under the coffee spouts:
- 1 cup if you want one coffee;
- 2 cups if you want 2 coffees.
3. Lower the spouts as near as possible to the
cup. This makes a creamier coffee (fig. 11).
4. Press the button corresponding to the
adjusting the coffee mill
The coffee mill is preset in the factory to make
coffee correctly and should not require adjusting
initially.
However, if after making the first few coffees you
find that the coffee is too thin and not creamy
enough or that delivery is too slow (a drop at
a time), this can be corrected by adjusting the
grinding adjustment knob (fig. 9).
number of coffees required (1 cup
or 2
cups , figs. 8 and 12).
5. Preparation begins. The amount of coffee
selected is displayed together with a progress
bar which gradually fills as preparation
progresses.
Please note:
Please note!
•
•
While the coffee maker is making coffee,
delivery can be interrupted at any moment by
pressing one of the two coffee buttons (
The grinding adjustment knob must only be
turned when the coffee mill is in operation.
If the coffee is delivered too
or
).
slowly or not at all, turn one
click clockwise towards “7”.
For fuller bodied creamier
coffee on the other hand,
turn one click anticlockwise
towards “1” (do not turn
more than one click at a time
At the end of delivery, to increase the quantity
of coffee in the cup, just press (within 3
seconds) one of the coffee buttons (
or
).
Once the coffee has been made, the appliance is
ready to use again.
otherwise the coffee could be delivered a drop
at a time).
These adjustments will only be evident after at
least 2 cups of coffee have been delivered.
If this adjustment does not obtain the desired
result, turn the knob another click.
Please note!
For hotter coffee, see the section “Tips for a
hotter coffee” (page 13).
Various messages (fill tank, empty grounds
container, etc.) will be displayed while using
the machine. Their meaning is explained in
the section “Displayed messages” (page 21).
•
•
tips for a hotter coffee
For a hotter coffee, before delivery you are
recommended to:
Important!
•
If the coffee is delivered a drop at a time, too
thin and not creamy enough or too cold, read
the tips in the “Troubleshooting” section on
page 22.
•
rinse the appliance through by pressing the
button. Hot water flows out of the coffee
spouts and heats the internal circuit of the
machine so that the coffee delivered will be
hotter.
13
making coffee using pre-ground coffee
lid and hot water nozzle as described in
the sections “Cleaning the milk frother
with the CLEAN button” on page 15 and
“Cleaning the milk container” on page
17.
Important!
•
•
Never add pre-ground coffee when the
machine is off or it could spread through the
inside of the machine and dirty it. This could
damage the appliance.
3. Make sure the milk intake tube is correctly
inserted in the bottom of the milk container
lid (fig. 16).
4. Place the lid back on the milk container.
5. Remove the hot water spout from the nozzle
(fig. 17).
6. Attach the milk container to the nozzle and
push as far as it will go (fig. 18). The machine
emits a beep.
7. Place a sufficiently large cup under the coffee
and frothed milk spouts. Adjust the length of
the milk spout. To move it nearer the cup,
simply pull it downwards (fig. 19).
8. Follow the instructions below for each
function.
Never use more than 1
level measure or it could
dirty the inside of the
coffee maker or block the
funnel.
Please note!
If you use pre-ground coffee, you can only
make one cup of coffee at a time.
1. Press the
button (fig. 6) until “Pre-
ground” is displayed.
2. Make sure the funnel is not blocked, then
add one level measure of pre-ground coffee
(fig. 13).
3. Place a cup under the coffee spouts.
making cappuccino or macchiato
1. After attaching the milk container, turn the
4. Press the 1 cup coffee button
(fig. 8).
5. Preparation begins. The amount of coffee
selected is displayed together with a progress
bar which gradually fills as preparation
progresses.
froth adjustment knob on the milk container
lid between position 2
20).
and 3
(fig.
2. Press the CAPPUCCINO button on the control
panel. “CAPPUCCINO” is displayed, together
with a progress bar which fills gradually
as preparation proceeds. If the froth is not
satisfactory, turn the froth adjustment knob
makinG Drinks With milk
Please note!
To avoid milk with poor froth or large bubbles,
always clean the milk lid and hot water nozzle
as described in the section “Cleaning the milk
container” on pages 15 and 17.
towards 2
(= less froth) or towards 3
(= more froth) (fig. 20).
3. After delivering the frothed milk, the machine
automatically makes the coffee.
filling and attaching the milk container
1. Remove the lid (fig. 14);
2. Fill the milk container with a sufficient
quantity of milk, not exceeding the MAX level
marked on the container (fig. 15). Each mark
on the side of the container corresponds to
3.4 oz / 100 ml of milk.
Please note!
•
•
•
If during delivery you want to stop making
milk or coffee, press the CAPPUCCINO
button twice.
At the end of delivery, to increase the quantity
of coffee in the cup, just press (within 3
seconds) the CAPPUCCINO button.
Do not leave the milk container out of the
refrigerator for longer than strictly necessary.
The warmer the milk (41°F/5°C ideal), the
poorer the froth will be.
Please note!
•
•
For a denser more even froth, we
recommend using skim or 2% milk
at refrigerator temperature (about
41°F/5°C).
To avoid producing milk with poor froth
or large bubbles, always clean the milk
making frothed milk (without coffee)
Proceed as described in the previous paragraph
14
(Making cappuccino or macchiato), pressing the
CAPPUCCINO button twice instead of once.
been delivered into the cup, press the
CAPPUCCINO button again.
5. The appliance stops delivering milk and after
a few seconds the coffee is delivered into the
cup. “Coffee for Cappucc. Program Quantity”
is displayed.
en
Please note!
If during delivery you want to stop making milk
or coffee, press the CAPPUCCINO button once.
6. Once the required quantity of coffee has
been delivered into the cup, press the
CAPPUCCINO button. Coffee delivery stops.
The machine is now reprogrammed with the new
quantities.
preparing milk (unfrothed and without coffee)
Proceed as described in the previous paragraph
(Making frothed milk), turning the froth
adjustment knob to position 1
(fig. 20).
cleaning the milk frother with the clean
button
“Press CLEAN button” flashes on the display
each time you use a milk function.
To eliminate all milk residues, proceed as
follows:
heatinG Water
Important! Danger of burns.
Never leave the machine unsupervised while
delivering hot water.
The spout becomes hot during delivery. Hold by
the plastic handle only.
1. Leave the milk container in the machine (you
do not need to empty it);
2. Place a cup or other recipient under the
frothed milk spout.
3. Press the CLEAN button (fig. 21) and keep
pressing until the progress bar which
appears on the display together with the
message “Cleaning...” is complete.
1. Make sure the hot water spout is attached
correctly (fig. 4).
2. Place a container under the spout (as close
as possible to avoid splashes).
3. Press the
button (fig. 2). “Hot water…”
progress
is displayed, together with
a
Please note!
bar which fills gradually as preparation
proceeds.
4. The machine delivers 8.5 oz / 250 ml of hot
water, then delivery stops automatically. To
interrupt delivery of hot water manually,
•
•
If you are making a number of cappuccinos
one after the other, you do not need to clean
by pressing the CLEAN button each time you
make a cappuccino. Just press it once after
making the last cappuccino (the appliance
can continue making cappuccino or coffee
even if the CLEAN button is not pressed).
After use, always clean the hot water/steam
nozzle and the milk container as described
on pages 17-18.
press the
button again.
Please note!
If “Energy Saving” mode is active, you may have
to wait a few seconds before the hot water is
delivered.
change the quantity of water delivered
automatically.
programming the quantity of coffee and milk
in the cup for cappuccino or milk
The machine is set by default to automatically
delivery 8.5 oz / 250 ml of hot water.
To modify these quantities, proceed as follows:
1. Position a container under the spout.
The appliance is set by default to automatically
deliver standard quantities.
To change these quantities, proceed as follows:
1. Place a cup under the coffee and milk
spouts.
2. Hold the CAPPUCCINO button until the
message “Milk for Cappuccino Program
Quantity” is displayed.
3. Release the button. The appliance starts
delivering milk.
4. Once the required quantity of milk has
2. Press the
Program Quantity” is displayed, then release
the button.
3. When the hot water in the cup reaches the
required level, press the button again.
button again until “Hot Water
The machine is now reprogrammed with the new
quantity.
15
showing the level of water it contains (fig. 23).
Before the indicator protrudes from the cup
tray, the drip tray must be emptied and cleaned,
otherwise the water may overflow the edge and
damage the appliance, the surface it rests on or
the surrounding area.
cleaninG
Important!
•
Do not use solvents, abrasive detergents
or alcohol to clean the coffee maker. With
De’Longhi superautomatic coffee makers,
you need not use chemical products to clean
the machine.
To remove the drip tray:
1. Remove the drip tray and the grounds
container (fig. 22);
2. Empty the drip tray and grounds container
and wash them;
3. Check the red condensate tray and empty if
necessary.
•
•
None of the components can be washed in
a dishwasher apart from the milk container
(D).
Do not use metal objects to remove
encrustations or coffee deposits as they
could scratch metal or plastic surfaces.
4. Replace the drip tray and grounds container.
cleaning the coffee grounds container
When “EMPTY GROUNDS CONTAINER” is
displayed, the grounds container must be
emptied and cleaned.
cleaning the inside of the coffee maker
Danger of electric shock!
Before cleaning internal parts, the machine must
be turned off (see “Turning off”) and unplugged
from the mains power supply. Never immerse
the coffee maker in water.
Until the grounds container has been cleaned,
the appliance continues to display the message
and coffee cannot be made.
Important! Danger of burns
If you make a number of cappuccinos one after
the other, the metal cup tray becomes hot.
Wait for it to cool down before touching it and
handle it from the front only.
1. Check regularly (about once a month) that
the inside of the appliance (accessible
after removing the drip tray) is not dirty. If
necessary, remove coffee deposits with the
brush provided or a sponge.
2. Remove the residues with a vacuum cleaner
(fig. 24).
To clean (with the machine on):
•
Remove the drip tray (fig. 22), empty and
clean.
cleaning the water tank
•
Empty the grounds container and clean
thoroughly to remove all residues left on the
bottom. This can be done with the spatula on
the brush provided.
Check the condensate tray (red) and empty if
necessary.
1. Clean the water tank (A9) regularly (about
once a month and whenever you replace
the water softener filter (if provided) with a
damp cloth and a little mild dish soap.
2. Remove the filter (if present) and rinse with
running water.
•
Important!
3. Replace the filter (if provided), fill the tank
with fresh water and replace the tank.
When removing the drip tray, the grounds
container must be emptied, even if it contains
few grounds.
cleaning the coffee spouts
If this is not done, when you make the next
coffees, the grounds container may fill up more
than expected and clog the machine.
1. Regularly clean the coffee spouts with a
sponge or cloth (fig. 25A).
2. Check the holes in the coffee spout are not
blocked. If necessary, remove coffee deposits
with a toothpick (fig. 25B).
cleaning the drip tray and condensate tray
Important!
cleaning the pre-ground coffee funnel
Check regularly (about once a month ) that the
The drip tray is fitted with a level indicator (red)
16
pre-ground coffee funnel (A6) is not blocked.
If necessary, remove coffee deposits with the
brush (C2) supplied.
en
cleaning the infuser
The infuser (A11) must be cleaned at least once
a month.
7. Once inserted, make sure the two red buttons
have snapped out.
Important!
The infuser may not be extracted when the
machine is on.
1. Make sure the machine is correctly turned
off (see “Turning the appliance off” on page
10).
PUSH
2. Remove the water tank.
3. Open the infuser door (fig. 26) on the right
side.
4. Press the two red release buttons inwards
and at the same time pull the infuser
outwards (fig. 27).
8. Close the infuser door.
9. Replace the water tank.
Important!
RINSE WITH WATER ONLY
NO DISH WASHING LIQUID - NO DISH
WASHER
Clean the infuser without using dish soap as
it could be damaged.
cleaning the milk container
Clean the milk container as described below each
time you prepare milk:
1. Remove the lid.
2. Remove the milk
spout and intake tube.
5. Soak the infuser in water for about 5 minutes,
then rinse under the tap.
6. Use the brush (C2) to remove any coffee
residues left in the infuser housing, visible
through the infuser door.
7. After cleaning, replace the infuser by sliding it
onto the internal support; then push the PUSH
symbol fully in until it clicks into place.
3. Turn
the
froth
adjustment knob to
the“INSERT”position
(see figure) and pull
it off upwards.
4. Wash
all
the
c o m p o n e n t s
thoroughly with hot
water and mild dish
soap.Allcomponents
are dishwasher safe,
placing them in the
top basket of the
dishwasher.
Make sure there are
no milk residues
in the hollow and
groove under the
knob (see figure
Please note!
If the infuser is difficult to insert, before insertion,
adapt it to the right size by pressing the two
levers shown in the figure.
alongside).
If
necessary, scrape
the groove with a
toothpick.
17
5. Rinse the inside of the
froth adjustment knob
under running water
(see figure alongside).
6. Check that the intake
tube and spout are
alternating to
CONTAINER”
6. Completely empty the water tank (A9) and
remove the water softener filter (if present);
then empty the drip tray and the empty
grounds container and re-insert them.
“EMPTY GROUNDS
not clogged with milk
residues.
7. Replace the knob
(lining up the arrow
with the word “INSERT”) the spout and the
milk intake tube.
8. Place the lid back on the milk container.
7. Pour the descaler into the tank up to the level
A (corresponding to a 3.4 oz / 100 ml pack)
marked on the back of the tank (fig. 28A),
then add water (34oz. / one litre) up to level
B (fig. 28B); reinsert the water tank.
8. Place an empty container with a minimum
capacity of 50.7 oz. / 1.5 litres under the hot
water spout (fig. 4).
cleaning the hot
Important! Danger of burns
Hot water containing acid flows from the change
to hot water spout.
water/steam nozzle
Each time you prepare
milk, clean the nozzle
Avoid contact with splashes of water.
with
a
sponge to
remove milk residues
from the gaskets (see
figure).
9. Press the
button to confirm introduction
of the solution.
The message “Descaling...” is displayed.
Thedescalingprogramstartsandthedescaler
liquid comes out of the water spout.
The descale program automatically performs
a series of rinses and pauses to remove
limescale deposits from inside the machine.
Descale
Descale the machine when the message
“DESCALE!” flashes on the display.
Important!
Descaler contains acids which may irritate the
skin and eyes.
Please note!
It is normal that the appliance is inactive for
several minutes between once rinsing and the
other.
After about 30 minutes, the message “FILL
TANK!” is displayed.
7. The appliance is now ready for rinsing
through with clean water. Remove the water
tank, empty, rinse under running water, fill
with clean water and replace. “Rinsing”
is displayed. “Rinsing... Confirm?” is
displayed.
8. Empty the container used to collect the
descaler solution and replace it empty under
the hot water spout.
It is vital to respect the manufacturer’s safety
warnings given on the descaler pack and the
warnings relating to the procedure to follow in
the event of contact with the skin and eyes.
Please note!
Use De’Longhi descaler only.
Under no circumstances should you use
sulphamic or acetic based descalers. Their use
invalidates the guarantee. Failure to descale
the appliance as described also invalidates the
guarantee.
1. Turn the machine on and wait for the
appliance to be ready for use.
2. Press the p button to enter the menu.
3. Turn the selection knob (fig. 7) until
“Descaling” is displayed.
9. Press the
button to start rinsing. Hot
water flows out of the spout and the message
“Rinsing...” is displayed.
10. When the water tank is completely empty, “
Rinsing complete Confirm?” is displayed.
4. Select by pressing the
button: Descaling
Confirm?” is displayed. Press
activate the function.
again to
11. Press the
button.
5. The message “Add descaler Confirm?”
12. Insert the filter (if it was present) in the tank,
18
fill the water tank again and the appliance is
ready for use.
you are recommended to purchase one from
De’Longhi Customer Services. To use the filter
correctly, follow the instructions below.
en
settinG Water harDness
installing the filter
The DESCALE! message is displayed after a
period of time established according to water
hardness. The machine is factory set for a
hardness value of 4. The machine can also be
programmed according to the hardness of water
in various regions so that the machine needs to
be descaled less often.
1. Remove the filter from the packaging.
2. Turn the date indicator disk (see fig. 29) until
the next 2 months of use are displayed.
Please note
The filter lasts about two months if the appliance
is used normally. If the coffee maker is left unused
with the filter installed, it will last a maximum of
three weeks.
measuring water hardness
1. Remove the “TOTAL HARDNESS TEST”
indicator paper attached to this manual from
its pack.
3. Remove the tank from the appliance and fill
with water.
4. Insert the filter in the water tank and immerse
it completely for ten or so seconds, sloping it
to enable the air bubbles to escape (fig. 30).
5. Insert the filter in the filter housing (fig. 31A)
and press as far as it will go.
6. Close the tank with the lid (fig. 31B), then
replace the tank in the machine.
When you install the filter, you must notify the
appliance of its presence.
7. Press the p button to enter the menu;
8. Turn the selection knob (fig. 7) until “Install
filter” is displayed;
2. Immerse the paper completely in a glass of
water for one second.
3. Remove the paper from the water and shake
lightly.
After about a minute, 1, 2, 3, or 4 red squares
form, depending on the hardness of the water.
Each square corresponds to one level.
soft water l
slightly hard water
ll
9. Press the
10. The message “Activate?” is displayed.
11. Pressthe buttontoconfirmtheselection.
“ Hot water Confirm?” is displayed.
12. Position container with minimum
button;
hard water lll
very hard water
llll
a
a
capacity of 3.4 oz / 100 ml under the hot
water spout.
set water hardness
13. Pressthe
buttontoconfirmtheselection.
The appliance begins delivering hot water and
the message “ Please wait... “ is displayed.
14. After delivery, the appliance returns
automatically to the “Ready for coffee”
position.
1. Press the p button to enter the menu.
2. Turn the selection knob to select “ Water
hardness “.
3. Confirm the selection by pressing the
button.
4. Turn the selection knob (fig. 7) and set the
level shown by the indicator paper (see
previous paragraph).
The new filter is active and indicated by an
asterisk displayed under “Install filter” in the
menu. You can now use the coffee maker.
5. Press the
button to confirm the setting.
6. Press the
The machine is now reprogrammed with the new
water hardness setting.
button to exit the menu.
replacing the filter
When “REPLACE FILTER!” is displayed, after
two months (see date indicator) or when the
appliance has not been used for 3 weeks, you
should replace the filter:
Water softener filter
Certain models are fitted with a water softener
filter. If this is not the case with your model,
1. Remove the exhausted filter;
19
2. Remove the new filter from the packaging;
3. Turn the date indicator disk (see fig. 29) until
the next 2 months of use are displayed (the
filter lasts about two months);
technical specification
Voltage:
120V~ 60Hz
Absorbed power:
Pressure:
1250W
15 bars
4. Refill the tank;
Water tank capacity:
Size LxHxD:
60 fl oz max
9.4x13.8x16.9 in
3.5 ft
5. Insert the filter in the water tank and immerse
it completely, sloping it to enable the air
bubbles to escape (fig. 30);
Cable length:
Weight:
20,22 lb.
6. Place the filter in the filter housing (fig. 31A)
and press as far as it will go. Close the tank
with the lid (fig. 31B), then replace the tank
in the machine;
Beans container capacity:
8.8 oz max
7. Position
a
container with
a
minimum
capacity of 3.4 oz / 100 ml under the hot
water spout;
8. Press the p button to enter the menu;
9. Turn the selection knob (fig. 7) until “Replace
“ is displayed;
10. Press the
button;
11. The message “Confirm?” is displayed;
12. Press the
selection;
button to confirm the
13. “Hot Water… Confirm?” is displayed.
14. Press the button to confirm the
selection. The appliance begins delivering
hot water and the message “Please Wait... “
is displayed.
15. After delivery, the appliance returns
automatically to the “Ready for coffee”
position.
The new filter is now active and you can use the
coffee maker.
removing the filter
If you want to continue using the appliance
without a filter, you must remove it and notify the
appliance of its removal as follows:
1. Extract the tank and exhausted filter;
2. Press the p button to enter the menu;
3. Turn the selection knob (fig. 7) until “Install
filter*” is displayed;
4. Press the
5. “Deactivate?” is displayed;
6. Press the button to confirm and the
button to exit the menu.
button;
20
DisplayeD messaGes
DisplayeD messaGe possiBle cause
en
remeDy
•
•
Insufficient water in the tank.
•
Fill the tank with water and/or insert it
correctly, pushing it as far as it will go
until it clicks into place (fig. 3B).
FILL TANK !
The grounds container (A14) is full.
•
Empty the grounds container and
drip tray, clean and replace (fig. 22).
Important: When removing the drip tray,
the grounds container must be emptied,
even if it is not completely full. If this
is not done, when you make the next
coffees, the grounds container may fill
up more than expected and clog the
machine.
EMPTY GROUNDS
CONTAINER!
•
The grinding is too fine and the coffee is
delivered too slowly or not at all.
•
Repeat coffee delivery and turn the
grinding adjustment knob (fig. 9) one
click clockwise towards “7” while the
coffee mill is in operation. If after
making at least 2 coffees delivery is
still too slow, repeat the correction
procedure, turning the grinding
GROUND TOO FINE
ADJUST MILL!
alternating with...
insert water spout and
press OK
adjustment knob another click (see the
section “Adjusting the coffee mill” on
page 13). If the problem persists, press
the
button and deliver a little
water from the spout.
•
•
After cleaning, the grounds container
•
•
Remove the drip tray and insert the
INSERT GROUNDS
CONTAINER!
has not been replaced.
grounds container.
The “pre-ground coffee” function has
been selected without placing any pre-
ground coffee in the funnel.
Place pre-ground coffee in the funnel or
deselect the “pre-ground” function.
ADD PRE-GROUND
COFFEE!
•
•
The machine must be descaled.
•
•
The descaling procedure described in the
“Descaling” section (page 17) needs to be
performed as soon as possible.
DESCALE!
Too much coffee has been used.
Select a milder taste or reduce the
quantity of pre-ground coffee.
LESS COFFEE!
•
•
The coffee beans have run out.
•
•
Fill the beans container
FILL BEANS
CONTAINER!
The pre-ground coffee funnel is clogged.
Empty the funnel with the help of a brush
as described in the section “Cleaning the
pre-ground coffee funnel”.
•
The infuser has not been replaced after
cleaning.
•
Insert the infuser as described in the
section “Cleaning the infuser” (page 17).
INSERT INFUSER
ASSEMBLY!
•
•
The tank is not correctly in place.
•
•
Insert the tank correctly and press as far
INSERT TANK
as it will go.
The inside of the appliance is very dirty.
Clean the inside of the appliance
GENERAL ALARM!
thoroughly, as described in the section
“Cleaning and maintenance” (page 16).
If the message is still displayed after
cleaning, contact a customer services.
•
The water softener filter is exhausted.
•
Replace the filter or remove it as
described in the section “Water softener
filter” (page 19).
REPLACE FILTER
21
DisplayeD messaGe possiBle cause
remeDy
•
Milk has been delivered recently and the
tubes inside the milk container must be
cleaned.
•
Press the CLEAN button and keep it
Press CLEAN button
pressed until the progress bar which
appears on the display together with the
message “Cleaning...” is complete.
•
•
The hot water spout is not inserted or is
inserted incorrectly.
•
•
Insert water spout as far as it will go.
INSERT WATER SPOUT
The milk container is not inserted
correctly.
Insert the milk container as far as it will
go.
INSERT MILK
CONTAINER!
trouBleshootinG
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact Customer Services.
proBlem
possiBle cause
remeDy
•
The cups were not preheated.
•
Warm the cups by rinsing them with hot
water (Note: you can use the hot water
function).
The coffee is not hot
•
The infuser has cooled down because
2/3 minutes have elapsed since the last
coffee was made.
•
Before making the coffee, warm the
infuser by pressing the
button .
•
•
Low coffee temperature is set.
•
•
In the menu, set a high coffee
temperature.
The coffee is ground too coarsely.
Turn the grinding adjustment knob one
click anticlockwise towards “1” while
the coffee mill is in operation (fig. 9).
Continue one click at a time until coffee
delivery is satisfactory. The effect is only
visible after delivering 2 coffees (see the
section: “Adjusting the coffee mill” on
page 13).
The coffee is thin or
not creamy enough.
•
•
The coffee is unsuitable.
•
•
Use pre-ground coffee for espresso
coffee makers
The coffee is ground too finely.
Turn the grinding adjustment knob
one click clockwise towards “7” while
the coffee mill is in operation (fig. 9).
Continue one click at a time until coffee
delivery is satisfactory. The effect is only
visible after delivering two coffees. (see
the section “Adjusting the coffee mill” on
page 13).
The coffee is delivered
too slowly or a drop at
a time.
•
•
The spouts are blocked.
•
•
Clean the spouts with a toothpick (fig.
Coffee does not come
out of one of the
spouts.
25B).
The milk container lid is dirty.
Clean the milk container lid as described
in the section “Cleaning the milk
container” .
The milk does not
come out of the milk
spout.
22
proBlem
possiBle cause
remeDy
en
•
The milk container lid or froth
•
Clean the milk container lid and knob as
described in the section “Cleaning the
milk container” (page 17).
The milk is not frothed,
or contains large
bubbles and squirts out
of the milk spout.
adjustment knob is dirty
•
The milk is not cold enough or is not
semi-skimmed.
•
We recommend using skim or 2%
milk at refrigerator temperature (about
41°F/5°C). If the result is not as you
wished, try changing brand of milk.
•
•
The froth adjustment knob is incorrectly
•
•
Adjust following the instructions in the
adjusted.
section on preparing drinks with milk.
The hot water/steam nozzle is dirty
Clean the nozzle as described in the
section “Cleaning the hot water/steam
nozzle”.
•
•
It is not plugged into the electrical
•
•
Plug into the electrical socket.
The appliance does not
come on.
socket.
The main switch (A8) is not turned on.
Push the main switch (fig. 1).
23
limiteD Warranty
This warranty applies to all products with De’Longhi or Kenwood brand names.
What does the warranty cover?
We warrant each appliance to be free from defects in material and workmanship. Our obligation under
this warranty is limited to repair at our factory or authorized service center of any defective parts or part
thereof, other than parts damaged in transit. In the event of a products replacement or return, the unit
must be returned transportation prepaid. The repaired or new model will be returned at the company
expense.
This warranty shall apply only if the appliance is used in accordance with the factory directions, which
accompany it, and on an Alternating current ( AC ) circuit.
how long does the coverage last?
This warranty runs for two years (2) from the purchase date found on your receipt and applies only to
the original purchaser for use.
What is not covered by the warranty?
The warranty does not cover defects or damage of the appliance, which result from repairs or alterations
to the appliance outside our factory or authorized service centers, nor shall it apply to any appliance,
which has been subject to abuse, misuse, negligence or accidents. Also, consequential and incidental
damage resulting from the use of this product or arising out of any breach of contract or breach of this
warranty are not recoverable under this warranty. Some states do not allow the exclusion or limitation
of incidental or consequential damage, so the above limitation may not apply to you.
how do you get service?
If repairs become necessary, see contact information below:
u.s. residents: Please contact our toll free hotline at 1-866-528-8323 (1-866-Latte-Best) or log onto
residents of canada: Please contact our toll free hotline at 1-888-335-6644 or log onto our website at
residents of mexico: Please contact our toll free number 01-800-711-8805 for assistance or log onto
The above warranty is in lieu of all other express warranties and representations. All implied warranties
are limited to the applicable warranty period set forth above. This limitation does not apply if you enter
into an extended warranty with De’Longhi. Some states/countries do not allow limitations on how long
an implied warranty lasts, so the above exclusions may not apply to you. De’Longhi does not authorize
any other person or company to assume for it any liability in connection with the sale or use of its
appliance.
how does country law apply?
This warranty gives you specific legal rights, and you may also have other rights, which vary from state
to state/country to country.
24
|