La Crosse Technology WS 6118 User Manual

WS-6118  
ATOMIC CLOCK WITH OUTDOOR WIRELESS TEMPERATURE AND  
MOON PHASE  
OUTDOOR TEMPERATURE TRANSMITTER:  
Instruction Manual  
Holder  
FEATURES:  
ATOMIC CLOCK:  
Hanging holes  
ꢀꢁ ꢂ ꢈꢉꢂ  
Remote transmission of outdoor temperature to the atomic clock by 433 MHz signals  
Wall mounting case  
LCD1  
display  
Function keys  
Foldable stand  
TO INSTALL AND REPLACE BATTERIES IN THE ATOMIC CLOCK  
The atomic clock uses 2 x AA, 1.5V batteries. To install and replace the batteries, please follow the  
steps below:  
LCD2  
display  
1.  
Insert finger or other solid object in the space at the bottom center of the battery compartment  
and lift up to remove the cover.  
2.  
3.  
Insert batteries observing the correct polarity (see marking inside battery compartment).  
Replace compartment cover.  
WWVB Radio controlled time with manual time setting  
12/24 hour time display  
Time display: hour, minute, second  
Alarm setting with snooze function  
Calendar display  
Battery cover  
DO NOT SET THE CLOCK.  
TO INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE TRANSMITTER  
The transmitter uses 2 x AA,1.5V batteries. To install and replace the batteries, please follow the  
steps below:  
1.  
2.  
3.  
Weekday display (3 languages to choose from: English, French and Spanish)  
Time zone setting  
Remove the cover.  
Insert the batteries, observing the correct polarity (see marking inside battery compartment).  
Replace the battery cover on the unit.  
Daylight savings time ON/OFF option (DST)  
ºC or ºF temperature display selectable  
Indoor temperature display  
Outdoor temperature display via 433MHz transmission  
Wall mount or freestanding  
Alkaline batteries are recommended for use in both units. Avoid using rechargable batteries.  
SETTING UP:  
Current moon phase display  
The DST default is “ON”, meaning that the WWVB will automatically change the time according to  
Daylight Saving Time in the spring and fall. For areas that do not recognize DST changes (Arizona  
and parts of Indiana) turn the DST “OFF”.  
LANGUAGE SETTING  
The weekdays can be displayed in LCD2 with the pre-set languages: US English, French and  
Spanish.  
Month setting  
Date setting  
Weekday setting  
12/24 hour time display setting  
ºC or ºF setting  
TIME ZONE SETTING  
After entering the manual setting mode as described above, the time zone can be set between the –1  
to –12 hour or Greenwich Mean Time (GMT) range in LCD2. To do this:  
1.  
2.  
Set the desired language for the weekday display in LCD 2 by use of the + key.  
Press and release the SET key to enter the mode “Manual Time Setting”.  
MANUAL TIME SETTING  
In case the atomic clock is not able to detect the WWVB-signal (disturbances, transmitting distance,  
etc.), the time can be manually set. The clock will then work as a normal Quartz clock.  
Note: In 12 hours mode the time will be displayed with an additional PMfor the time from 12:00  
noon until 11:59.  
1.  
2.  
3.  
4.  
The hour digits will start flashing on LCD1.  
Set the desired hours by pressing and releasing the + key followed by pressing the SET key.  
Now the minute digits will start flashing.  
Set the desired minutes by pressing and releasing the + key . If the + key is held, the units will  
increase by 5.  
Press and release the SET key to move to the “Year Setting”.  
1.  
The time zone (LCD2) will start flashing (Default setting "-5h“). Select the desired time zone by  
pressing and releasing the + key.  
Note: The time zones from –4 to –10 hours will be displayed with 3 characters abbreviations:  
-4 ATL (Atlantic time),  
-5 EST (Eastern time; default time zone),  
-6 CST (Central time),  
-7 MST (Mountain time),  
-8 PST (Pacific time),  
-9 ALA (Alaska time),  
-10 HAW (Hawaii time).  
"GMT” will be displayed if set to GMT (0).  
5.  
Note:  
The unit will still try and receive the signal every day despite it being manually set. When it does  
receive the signal, it will change the manually set time into the received time. During reception  
attempts the WWVB tower icon will flash. If reception has been unsuccessful, then the WWVB tower  
icon will not appear but reception will still be attempted the following hour.  
WWVB time reception takes place from 12:00 am through 6:00 am each day (attempts WWVB  
reception every full hour within this time frame). When the time signal is received for example at 1:00  
am, the atomic clock will not attempt to receive the WWVB signal for the remaining hours until 6:00  
am. Therefore, the next signal attempt will take place between 12:00 am and 6:00 am the next day.  
The other times WWVB reception takes place, are upon setup and after manual time set exiting  
mode. Reception is generally not possible during daylight hours due to the interference of the sun.  
2. Press and release the SET key to enter the “DST Setting“.  
DST SETTING (daylight saving time)  
1.  
2.  
The ON digit will start flashing on LCD1. Set the DST ON or OFF by pressing the + key.  
Press and release the SET key to enter the “Language Setting“.  
Note:  
If no keys are pressed for at least 15 seconds in setting mode, the atomic clock will  
automatically switch back to normal display mode.  
YEAR SETTING  
The year can be selected sequentially from 2000 to 2049 and will then start over again (default  
setting 2000). Only the last 2 digits of the year will be visible on LCD2 .  
1.  
2.  
The year digits will start flashing on LCD2. Select the desired year by use of the + key.  
Press and release the SET key to switch to the “Month Setting”.  
ALARM SETTING  
To enter into the alarm setting mode:  
MONTH SETTING  
1.  
2.  
3.  
4.  
5.  
Hold the ALM key for 4 seconds. The hour digits start flashing.  
Press and release the + key to set the hour.  
Press and release the ALM key to set the minutes. The minute digits start flashing.  
Press and release the + key to set the minutes.  
Press and release again the ALM key to exit the Alarm setting mode or wait for 15 seconds  
automatic timeout.  
1.  
2.  
The month digits on LCD2 will start flashing. Set the desired month by use of the + key.  
Press and release the SET key to move to the mode “Date Setting”.  
Date Setting  
1.The digits for the date will start flashing on LCD2 (Default setting 1). Set the desired date by use of  
the + key.  
Note: The date can only be set in conjunction with the selected month. For example, it is not possible  
to set the date 30 if the month of February is selected.  
Press and release the SET key to enter the “Weekday Setting”.  
TO DEACTIVATE THE ALARM:  
Alarm icon  
((())) (ON)  
WEEKDAY SETTING  
1.  
The weekday symbols will be displayed on LCD2 in the pre-set language and flashing. Set the  
desired weekday by use of the + key.  
The alarm will be automatically ON when the alarm time is set. To deactivate the alarm (OFF), press  
and release once the ALM key in normal mode display. The alarm icon will disappear, the alarm is  
now off  
2.  
Press and release the SET key to enter the mode “12/24 Hours Time Display Setting”.  
12/24 HOURS TIME DISPLAY SETTING  
1.  
The “12h” or “24h” will start flashing in LCD1 (Default setting 12h). Select the desired time  
display mode by use of the + key.  
SNOOZE SETTING  
The snooze can only be activated during alarm time for a snooze duration of 10 minutes by pressing  
the SNZ key on the back of the clock  
2.  
Press and release the SET key to enter the “ºC/ºF Temperature Setting“.  
°C OR °F TEMPERATURE SETTING  
OUTDOOR TEMPERATURE TRANSMITTER:  
The temperature is measured and transmitted to the atomic clock every 1 minute. The atomic clock  
will update the temperature display every 5 minutes.  
The range of the outdoor temperature transmitter may be affected by the temperature. At cold  
temperatures the transmitting distance may be decreased. Please bear this in mind when positioning  
the transmitter. Also the batteries may be reduced in power during periods of extreme cold  
temperatures.  
1.  
The characters “°C” or “°F” will start flashing on LCD1 (Default setting °F). By use of the + key  
select “°C” for temperature display in degrees Celsius or “°F” for degrees Fahrenheit.  
Press and release the SET key to exit the setting mode and switch back to the normal display  
mode .  
2.  
EXIT THE MANUAL SETTING MODES  
To return to the normal display mode from anywhere in manual setting mode simply press the  
SNZ key anytime.  
433MHz RECEPTION CHECK FOR OUTDOOR TEMPERATURE TRANSMITTER  
The atomic clock will receive the temperature data within 4 minutes. If the temperature data is not  
being received 4 minutes after setting up (the display shows “- - -”), then please check the following  
points:  
1. The distance of the atomic clock or outdoor temperature transmitter should be at least 6 feet (2  
meters) away from any interfering sources such as computer monitors or TV sets.  
2. Avoid placing the receiver onto or in the immediate proximity of metal window frames.  
3. Using other electrical products such as headphones or speakers operating on the same signal  
frequency (433MHz) may prevent correct signal transmission and reception.  
4. Neighbors using electrical devices operating on the 433MHz signal frequency can also cause  
interference.  
WWVB RADIO CONTROLLED TIME  
The NIST radio station, WWVB, is located in Ft. Collins, Colorado and transmits the exact time signal  
continuously throughout the United States at 60 kHz. The signal can be received up to 2,000 miles  
away through the internal antenna in the atomic clock. However, due to the nature of the Earth’s  
Ionosphere, reception is very limited during daylight hours. The atomic clock will search for a signal  
every night when reception is best. The WWVB radio station derives its signal from the NIST atomic  
clock in Boulder, Colorado. A team of atomic physicists continually measures every second of every  
day to an accuracy of ten billionths of a second a day. These physicists have created an international  
standard, measuring a second as 9,192,631,770 vibrations of a Cesium 133 atom in a vacuum. This  
atomic clock regulates the WWVB transmitter.  
Note:  
Once the outdoor temperature is displayed on the atomic clock, the WWVB tower icon in the clock  
display will start flashing in the top center of the LCD. This indicates that the clock has detected a  
radio signal and is trying to receive it. When the time code is received, the WWVB tower becomes  
permanently lit and the time will be displayed.  
When the 433 MHz signal is received correctly, do not re-open the battery cover of either the outdoor  
temperature transmitter or atomic clock, as the batteries may spring free from the contacts and force  
a false reset. Should this happen accidentally then reset all units (see Setting up above) otherwise  
transmission problems may occur.  
The maximum transmission range is 82 feet (25 meters) from the outdoor temperature transmitter to  
the atomic clock (in open space). However, this depends on the surrounding environment and  
interference levels. If no reception is possible despite the observation of these factors, all system  
units have to be reset (see Setting up).  
If the tower icon flashes, but does not set the time or the WWVB tower does not appear at all, then  
please take note of the following:  
Recommended distance to any interfering sources like computer monitors or TV sets is a  
minimum of 6 feet (2 meters).  
Within ferro-concrete rooms (basements, superstructures), the received signal is naturally  
weakened. In extreme cases, please place the unit close to a window and/ or point its front or back  
towards the Fort Collins, Colorado, transmitter.  
During nighttime, the atmospheric disturbances are usually less severe and reception is possible  
in most cases. A single daily reception is adequate to keep the accuracy deviation below 1  
second.  
CHANGING THE DISPLAY MODE (DAY, SECONDS, AND TEMPERATURES)  
There are three possible display modes to view the day, seconds, and temperatures.  
The month&date/weekday/indoor temperature/outdoor temperature is the default.  
To change the display:  
1. Press the + key. The display should now show the month&date/weekday/seconds/ indoor  
temperature.  
2. Press the + key a second time and the display will now show the month&date/seconds/indoor  
temperature/outdoor temperature.  
Note:  
In case the atomic clock is not able to detect the WWVB-signal (disturbances, transmitting distance,  
etc.), the time can be manually set (please refer to notes on Manual time setting)  
3.  
Press the + key third time and the display will return to the normal display.  
waterproof and should not be placed anywhere it will become submerged in water or be directly in the  
rain.  
MOON PHASE  
The Moon Phases, and their corresponding dates appear in LCD 2. There are 12 visible Moon  
Phases that will show in the LCD 2:  
POSITIONING THE ATOMIC CLOCK:  
There are two possible ways to mount the atomic clock:  
use of the foldout table stands, or  
wall mounting  
MOON PHASES FOR WS-8117  
FOLDOUT TABLE STAND  
The Foldout table stand legs are located on the backside, at the  
lower corners, and on both sides of the battery cover. The hinges  
are towards the edges of the atomic clock, and the ends (with no  
hinge) need to be folded out towards the edge. Once the Foldout  
table stands are extended, place the atomic clock in an appropriate  
location.  
New Moon Small Waxing Large Waxing First Quarter Small Waxing  
Crescent Crescent Gibbous  
Large Waxing  
Gibbous  
FullMoon  
Large Waning Small Waning Last Quarter Large Waning  
Gibbous Gibbous Crescent  
Small Waning  
Crescent  
WALL MOUNTING  
1) Using a straightedge, horizontally space at 2-3/4 of an inch (70 mm) three  
screw positions on a wall.  
POSITIONING  
2) Install three mounting screws (not included) into a wall within transmission  
range—leaving approximately 3/16 of an inch (5mm) extended from the wall.  
3) Place the atomic clock onto the screws, using the hanging holes on the  
backside. Gently pull the atomic clock down to lock the screws into place.  
Note:  
Before permanently mounting ensure that the atomic clock is able to receive WWVB signals from the  
desired location. Also, extreme and sudden changes in temperature will decrease the accuracy of the  
atomic clock, and changes in elevation will result with inaccurate temperatures readings for the next  
12 to 24 hours. These changes will require a 12 to 24 hour wait before obtaining reliable data.  
Always ensure that the atomic clock locks onto the screws before releasing.  
To achieve a true temperature reading, avoid mounting where direct sunlight can reach the outdoor  
temperature transmitter. It is recommended to mount the outdoor temperature transmitter on a  
North-facing wall or in any well shaded area. The maximum transmitting range is 82 feet (25 meters)  
obstacles such as walls, concrete, and large metal objects can reduce the range.  
POSITIONING THE OUTDOOR TEMPERATURE TRANSMITTER  
The outdoor temperature transmitter can be mounted in two ways:  
Place both units in their desired location, and wait approximately 10 minutes before permanently  
mounting to ensure that there is proper reception. The outdoor temperature transmitter is not  
with the use of screws, or using the adhesive tape.  
MOUNTING WITH SCREWS  
1) Move the atomic clock to an area with warmer or cooler surrounding  
temperature. Current surrounding temperatures are outside measuring  
range.  
"--.-" appears in the outdoor temperature section of the LCD.  
1) Remove the batteries of both units for one minute, then reinsert them  
again. Make sure the batteries are new and fresh.  
Solution:  
1)  
2)  
Remove the mounting bracket from the outdoor temperature transmitter.  
Place the mounting bracket over the desired location. Through the three  
screw holes of the bracket, mark the mounting surface with a pencil.  
Where marked, start the screw holes into mounting surface.  
Screw mounting bracket onto the mounting surface. Ensure that the  
screws are flush with the bracket.  
Problem:  
Solution:  
3)  
4)  
2) Move the atomic clock closer to the transmitter or place the transmitter  
closer to the atomic clock. Make sure the clock is at a receivable range  
from the transmitter.  
3) Move the units to another location. Interferences from other electrical  
devices operating on the same signal frequency (433MHz) may prevent  
correct signal transmission and reception.  
"OFL“ appears in the outdoor temperature section of the LCD.  
1) Wait until the current surrounding temperature cools down or increases.  
Current temperature is outside of the measuring range of the transmitter.  
The outdoor temperature will be displayed again once the current  
surrounding temperature is within the range of the transmitter.  
MOUNTING WITH ADHESIVE TAPE  
1) With a nonabrasive solution, clean and dry the back of the mounting  
bracket and the mounting surface to ensure a secure hold. The  
mounting surface should be smooth and flat.  
Problem:  
Solution:  
2) Remove the protective strip from one side of the tape. Adhere the  
tape to the designated area on the back of the mounting bracket.  
3) Remove the protective strip from the other side of the tape. Position  
the outdoor temperature transmitter in the desired location, ensuring  
that the atomic clock can receive the signal.  
CARE AND MAINTENANCE:  
TROUBLESHOOTING  
Avoid placing the units in areas prone to vibration and shock as these may cause damage.  
Avoid areas where the units can be exposed to sudden changes in temperature, i.e. direct  
sunlight, extreme cold and wet/moist conditions as these will lead to rapid changes which reduces  
the accuracy of readings.  
The LCD is faint.  
1) Replace the batteries.  
No reception of WWVB signal  
1) It may help reception to face the front of the atomic clock in the general  
direction of Ft. Collins, Colorado.  
Problem:  
Solution:  
Problem:  
Solution:  
When cleaning the LCD and casing, use a soft damp cloth only. Do not use solvents or scouring  
agents.  
Do not submerge the units into water.  
Immediately remove all low powered batteries to avoid leakage and damage. Replace only with  
new batteries of the recommended size.  
2) Wait overnight for signal.  
3) Be sure the atomic clock is at least 6 feet (2 meters) from any electrical  
devices, i.e. TV sets, computers, or other radio controlled clocks.  
4) Remove batteries for five minutes, reinsert and leave the unit alone  
overnight without pressing any keys.  
Do not make any repairs to the units. Please return it to the original point of purchase. Opening  
and tampering with the units may invalidate the warranty.  
Hour is incorrect (minute and date are correct).  
1) Be sure the correct time zone and daylight saving time are selected.  
"OFL“ appears in the indoor temperature section of the LCD  
Problem:  
Solution:  
Problem:  
Please help in the preservation of the environment and return used batteries to an  
authorized depot.  
SPECIFICATIONS:  
Temperature measuring range  
Indoor: +32ºF to +122ºF with 0.2ºF resolution  
0ºC to +50ºC with 0.1ºC resolution  
WARRANTY INFORMATION  
("OFL" displayed if outside this range)  
Outdoor : -21.8ºF to +140ºF with 0.2ºF resolution  
-29.9ºC to +59.9ºC with 0.1ºC resolution  
("OFL“ displayed if outside this range)  
Temperature checking interval  
La Crosse Technology provides a 1-year warranty on this atomic clock. Contact La Crosse  
Technology immediately upon discovery of any defects covered by this warranty.  
Before sending the atomic clock in for repairs, contact La Crosse Technology. The atomic clock will  
be repaired or replaced with the same or similar model.  
Indoor: every 10 seconds  
Outdoor: every 5 minutes  
This warranty does not cover any defects resulting from improper use, unauthorized repairs, faulty  
batteries, or the clocks inability to receive a signal due to any source of interference.  
Transmission distance: maximum 82 feet (25 meters) in open field, depending upon surrounding  
structures, mounting location and possible interfering sources  
Power source (Alkaline batteries recommended)  
Atomic clock : 2 x AA, 1.5V batteries  
Transmitter: 2 x AA, 1.5V batteries  
LA CROSSE TECHNOLOGY WILL NOT ASSUME LIABILITY FOR INCIDENTAL,  
CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE  
OPERATION OR MALFUNCTION OF THIS TEMPERATURE CLOCK. THIS PRODUCT IS NOT TO  
BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. THIS PRODUCT IS NOT  
A TOY. KEEP OUT OF CHILDRENS’ REACH.  
Battery life: about 12 months  
Dimensions (L x W x H)  
Atomic clock : 11.41“ x 0.98“ x 7.48“ / 290 x25 x190mm  
Transmitter: 1.57“ x 0.9“ x 5.04“ / 40 x 23 x 128 mm  
This warranty gives you specific legal rights. You may also have other rights specific to your State.  
Some States do not allow the exclusion of consequential or incidental damages; therefore the above  
exclusion of limitation may not apply to you.  
LIABILITY DISCLAIMER:  
For warranty work, technical support, or information contact:  
The manufacturer and supplier cannot accept any responsibility for any incorrect readings and any  
consequences that occur should an inaccurate reading take place.  
La Crosse Technology, Ltd  
2809 Losey Blvd. S.  
La Crosse, WI 54601  
Phone: 608.782.1610  
Fax: 608.796.1020  
This product is only designed for use in the home or office.  
This product is not to be used for medical purposes or for public information.  
The specifications of this product may change without prior notice.  
This product is not a toy. Keep out of the reach of children.  
No part of this manual may be reproduced without written authorization of the manufacturer.  
e-mail  
(warranty work)  
BATTERIES CHANGE:  
For best performance, batteries should be replaced at least once a year to maintain the best running  
accuracy. Ensure that the batteries used are new and the correct size.  
(information on other products)  
Or visit us on the internet at  
FCC ID: OMO-01RX (receiver)  
OMO-01TX (transmitter)  
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO  
THE FOLLOWING TWO CONDITIONS:  
1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND  
2. THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED, INCLUDING INTERFERENCE  
THAT MAY CAUSE UNDESIRED OPERATION.  
All rights reserved. This handbook must not be reproduced in any form, even in excerpts, or  
duplicated or processed using electronic, mechanical or chemical procedures without written  
permission of the publisher.  
This handbook may contain mistakes and printing errors. The information in this handbook is  
regularly checked and corrections made in the next issue. We accept no liability for technical  
mistakes or printing errors, or their consequences.  
All trademarks and patents are acknowledged.  
WS-6118  
Atomic Clock With Outdoor Temperature and Moon Phase  
Instruction Manual  
ꢀꢁ ꢈꢉꢂ  

MTD 243 650B000 User Manual
Jura Capresso IMPRESSA701 User Manual
HTC TOUCH Pro2 User Manual
HTC One S ONESTMB User Manual
Hayter Mowers 71620 User Manual
Hamilton Beach 44274 User Manual
Fellowes PS75 User Manual
Emerson MLT Analyzer Module NGA 2000 User Manual
Dell PRECISION 530 User Manual
Black & Decker DCM601W User Manual