American Audio®
Operating Instructions
PRO-DJ2FX
Featuring:
FLIPFLOP
Sampling
American Audio®
4295 Charter Street
Los Angeles Ca. 90058
Revised 6/01
ELECTRICAL SAFETY PRECAUTIONS
CAUTION: TO PREVENT ELECTRIC SHOCK
DO NOT USE THIS (POLARIZED) PLUG WITH
AN EXTENSION CORD, RECEPTACLE, OR
OTHER OUTLET UNLESS THE BLADES CAN
BE CAREFULLY INSERTED TO PREVENT
BLADE EXPOSURE
NOTE: This CD player uses a semiconductor
laser. It is recommended for use in a room
at the following temperature: 41˚F - 95˚F /
5˚C - 35˚C
CAUTION:
1. Handle the power supply cord carefully. Do
not damage or deform; it may cause electric
shock or malfunction when used. Hold plug
attachment when removing from wall outlet.
Do not pull on the cord.
2. To avoid electric shock, do not open the
top cover when the unit is plugged in. If
problems occur with the unit, call your local
American Audio® dealer.
ATTENTION: POUR PREVENIR LES CHOCS
ELECTRIQUES NE PAS UTILISER CETTE
FICHE POLARISEE AVEC UN PROLON-
GATEUR, UNE PRISE DE COURANT OU
UNE AUTRE SORTIE DE COURANT, SAUF SI
LES LAMES PEUVENT ETRE INSEREES A
FOND SANS EN LAISSER AUCUNE PARTIE
A DECOUVERT.
3. Do not place metal objects or spill liquid
inside the CD player. Electric shock or mal-
function may occur.
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS UNIT TO
WATER OR MOISTURE
The serial and model number for this unit
is located on the rear panel. Please write
down the numbers here and retain for future
reference.
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reason-
able protection against harmful interference in
a residential installation. This equipment gen-
erates, uses, and can radiate radio frequency
energy and, if not installed and used in accor-
dance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not
occur in a particular installation. If this equip-
ment does cause harmful interference to radio
or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
Model No._____________________________
Serial No._____________________________
NOTE: This product satisfies FCC regulations
when shielded cables and connectors are
used to connect the unit to other equipment.
To prevent electromagnetic interference with
electrical appliances such as radios and televi-
sions, use shielded cables and connectors for
connections.
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS
OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE
– Reorient or relocate the receiving antenna.
– Increase the separation between the equip-
ment and receiver.
– Connect the unit into an electrical outlet on a
circuit different from that to which the receiver
is connected.
THE COMPACT DISC PLAYER SHOULD NOT
BE ADJUSTED OR REPAIRED BY ANYONE
EXCEPT PROPERLY QUALIFIED SERVICE
PERSONNEL.
– Consult the dealer or an experienced radio/TV
technician for help.
©American Audio®
-
-
PRO-DJ2FX™ Instruction Manual Page 3
ELECTRICAL SAFETY PRECAUTIONS
ELECTRICAL PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product'senclosurethatmaybeofsufficientmagnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER (OR BACK).
THERE ARE NO USER SERVICEABLE PARTS
INSIDE REFER SERVICE TO YOUR AUTHORIZED
AMERICAN AUDIO® SERVICE TECHNICIAN.
IMPORTANT SAFETY INSTRUCTIONS
OBJECT AND LIQUID ENTRY - Never push objects of
READ INSTRUCTIONS — All the safety and operating
GROUNDING OR POLARIZATION
instructions should be read before the product is
operated.
•
Ifthisproductisequippedwithapolarizedalternating
current line plug (a plug having one blade wider than
theother), itwillfitintotheoutletonlyoneway. This
isasafetyfeature.Ifyouareunabletoinserttheplug
fullyintotheoutlet, tryreversingtheplug. Iftheplug
should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
any kind into this product through openings as they
may touch dangerous voltage points or short-out
parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
RETAIN INSTRUCTIONS — The safety and operating
instructionsshouldberetainedforfuturereference.
HEED WARNINGS — All warnings on the product and
in the operating instructions should be adhered to.
FOLLOW INSTRUCTIONS — All operating and use
instructions should be followed.
SERVICING — Do not attempt to service this product
yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
CLEANING — The product should be cleaned only with
a polishing cloth or a soft dry cloth. Never clean with
furniture wax, benzine, insecticides or other volatile
liquids since they may corrode the cabinet.
•
If this product is equipped with
a
three-wire
DAMAGEREQUIRINGSERVICE - Unplugthisproduct
from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
groundingtypeplug,aplughavingathird(grounding)
pin, itwillonlyfitintoagroundingtypepoweroutlet.
Thisisasafetyfeature.Ifyouareunabletoinsertthe
plug into the outlet, contact your electrician to
replace your obsolete outlet. Do not defeat the
safety purpose of the grounding type plug.
•
•
When the power-supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen into
the product.
ATTACHMENTS
—
Do not use attachments not
recommendedbytheproductmanufacturerasthey
may cause hazards.
WATER AND MOISTURE — Do not use this product
near water — for example, near a bathtub, wash
bowl,kitchensink,orlaundrytub;inawetbasement;
or near a swimming pool; and the like.
ACCESSORIES — Do not place this product on an
unstable cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a child or
adult, and serious damage to the product. Use only
•
•
If the product has been exposed to rain or water.
Iftheproductdoesnotoperatenormallybyfollowing
theoperatinginstructions.Adjustonlythosecontrols
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its
normal operation.
POWER-CORD PROTECTION - Power-supply cords
should be routed so that they are not likely to be
walked on or pinched by items placed upon or
against them, paying particular attention to cords at
plugs,conveniencereceptacles,andthepointwhere
they exit from the product.
OUTDOOR ANTENNA GROUNDING — If an outside
antennaorcablesystemisconnectedtotheproduct,
be sure the antenna or cable system is grounded so
astoprovidesomeprotectionagainstvoltagesurges
andbuilt-upstaticcharges.Article810oftheNational
ElectricalCode,ANSI/NFPA70,providesinformation
with regard to proper grounding of the mast and
supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding
conductors, location of antenna-discharge unit,
connection to grounding electrodes, and
requirementsforthegroundingelectrode.SeeFigure
A.
LIGHTNING — For added protection for this product
duringalightningstorm,orwhenitisleftunattended
and unused for long periods of time, unplug it from
the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product
due to lightning and power-line surges.
POWER LINES —An outside antenna system should
notbelocatedinthevicinityofoverheadpowerlines
or other electric light or power circuits, or where it
can fall into such power lines or circuits. When
installing an outside antenna system, extreme care
should be taken to keep from touching such power
lines or circuits as contact with them might be fatal.
OVERLOADING — Do not overload wall outlets,
extensioncords,orintegralconveniencereceptacles
as this can result in a risk of fire or electric shock.
•
•
If the product has been dropped or damaged in any
way.
When the product exhibits a distinct change in
performance — this indicates a need for service.
with
a
cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with
the product. Any mounting of the product should
follow the manufacturer’s instructions, and should
use a mounting accessory recommended by the
manufacturer.
REPLACEMENT PARTS -- When replacement parts
arerequired,besuretheservicetechnicianhasused
replacement parts specified by the manufacturer or
have the same characteristics as the original part.
Unauthorizedsubstitutionsmayresultinfire,electric
shock, or other hazards.
SAFETY CHECK - Upon completion of any service or
repairs to this product, ask the service technician to
performsafetycheckstodeterminethattheproduct
is in proper operating condition.
CART — A product and cart combination should be
moved with care. Quick stops, excessive force, and
uneven surfaces may cause the product and cart
combination to overturn.
WALL OR CEILING MOUNTING — The product should
not be mounted to a wall or ceiling.
HEAT —The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce
heat.
VENTILATION — Slots and openings in the cabinet are
provided for ventilation and to ensure reliable
operation of the product and to protect it from
overheating, and these openings must not be
blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug,
or other similar surface. This product should not be
placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
POWER SOURCES —This product should be operated
only from the type of power source indicated on the
marking label. If you are not sure of the type of
power supply to your home, consult your product
dealer or local power company.
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
LOCATION – The appliance should be installed in a
stable location.
NONUSE PERIODS – The power cord of the appliance
should be unplugged from the outlet when left un-
used for a long period of time.
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
Fig. A
NEC — NATIONAL ELECTRICAL CODE
©American Audio®
-
-
PRO-DJ2FX™ Instruction Manual Page 4
PRODUCT INFORMATION
This unit has been thoroughly tested and has
been shipped in perfect operating condition.
Carefully check the shipping carton for damage
that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect
your unit for any damage. Be sure all acces-
sories needed to operate the unit has arrived
intact. In the event damage has been found or
parts are missing, please contact our toll free
customer support number for further instruc-
tions. Please do not return the unit to your
dealer without first contacting customer sup-
port.
I. Heat - The CD player should be situated
away from heat sources such as radiators,
heat registers, stoves, or other appliances
(including amplifiers) that produce heat.
2. Do not let insecticides, benzene, or thinner
come in contact with the surface of the unit.
3. Never disassemble or modify your unit in
any way, doing so will void your manufactures
warranty.
4. Never plug this unit in to a dimmer pack
LINE VOLTAGE SELECTION
• The desired voltage may be set with the
VOLTAGE SELECTOR switch on the rear
panel (using a flat head screw driver).
• Do not force the VOLTAGE SELECTOR
switch as this may cause damage
5. Do not attempt to operate this unit if it becomes
damaged in any way.
6. This unit is intended for indoor use only, use
of this product outdoors voids all warranties.
• If the VOLTAGE SELECTOR switch does
not move smoothly, please contact a quali-
fied service technician.
7. Always mount this unit in safe and stable
matter.
8. Disconnect from main power before making
any type of connection.
9. Cleaning -
• The CD Player should be cleaned only as
recommended by the manufacturer. Use a
soft cloth to wipe down the outside of the
unit. For stubborn stains moisten a soft cloth
with class cleaner or other mild detergent to
wipe away any stains. Use a soft cloth to
wipe any residual cleaner. Never use volatile
cleaners such as benzene, solvent, or thinner
to clean your unit, these cleaners will damage
the units surface.
• Cleaning the pick-up lens - The pick-up lens
should not become dirty under normal usage.
If the lens does become dirty, contact
American Audio Technical Support for further
instructions. Third party lens cleaners avail-
able but not highly recommended. Use of
some of these cleaner may damage the pick-
up lens, be sure to follow extreme caution
when using these types of cleaners.
VOLTAGE SELECTOR SWITCH
WARRANTY INFORMATION
The PRO-DJ2FX™ carries a TWO year (730
days) limited warranty. This warranty covers
parts and labor. Please fill out the enclosed
warranty card to validate your purchase and
warranty. All returned service items whether
under warranty or not, must be freight pre-paid
and accompany a return authorization (R.A.)
number. If the unit is under warranty, you
must provide a copy of your proof of purchase
invoice. Please contact American Audio® cus-
tomer support at (800) 322-6337 for a R.A.
number.
©American Audio®
-
-
PRO-DJ2FX™ Instruction Manual Page 5
CUSTOMER SERVICE
Customer Support: American Audio® provides a toll free customer support line, to provide set up help and to
answer any question should you encounter problems during your set up or initial operation. You may also visit us
American Audio®. Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time.
Voice:
Fax:
(800) 322-6337
(323) 582-2610
E-mail:
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will
void your manufactures warranty. In the unlikely event your unit may require service please contact customer
support. Please do not return to your dealer without first contacting customer support.
SET-UP
1. Checking the Contents:
Be sure your PRO-DJ2FX™ was shipped with the following:
1) PRO-DJ2FX™ Professional CD player.
1) One dual stereo RCA cable.
1) Warranty card.
1) Operating instructions (this booklet).
1) One male to male 1/8” mini plug.
2. Installing the Units
1) Place your unit on a flat surface or mount it in a secure case such as optional PRO-DJ/CASE.
2) Be sure the player is mounted in a well ventilated area where it will not be exposed to direct sunlight,
high temperatures, or high humidity.
3) Try to place the unit as far as possible from TVs and tuners, as the unit may cause undesirable
interference.
3. Connections
1) Be sure main power is connected last to prevent any electrical damage.
2) AUDIO CONNECTIONS: Use the included RCA cable to connect the PRO-DJ2FX™ outputs to the line
inputs of a mixer. Never connect a CD player's output to a mixers "phono" inputs.
3) CONTROL JACK CONNECTIONS: Use the supplied 1/8” mini plug cable to connect your PRO-
DJ2FX™
“Fader Q Start” mixer. (This will
“Q” start control page 7)
to a mini jack connection (A or B) on a compatible American Audio
enable the Fader “Q” Start function - See
CAUTION: Be sure to use the supplied control cables. Using different types of cables may result
in unit damage. To avoid server unit damage, be sure main power is off when connecting the
CAUTION:
CAUTION:
• The LCD is designed to be clearly visible within the
angles shown in Figure 2. Mount the control unit
so that the visual angle is within this range.
10˚ 50˚
• The player will work normally when the main unit is
mounted with the front panel within 15 degrees of
the vertical plane. If the unit is tilted excessively,
discs may not be loaded or unloaded properly.
(Figure 1)
15˚
Figure 1
Figure 2
©American Audio®
-
-
PRO-DJ2FX™ Instruction Manual Page 6
MAIN FEATURES
• 8 times over sampling 1 bit D/A converter
• 20 Seconds Digital Anti-Shock Protection
• 4 Programmable Cue Points
• Reverse Playback
• Selectable Time Display
• Break Effect
• Coast Effect
• Auto cue Function (Sensitive to -48dB)
• Realtime Cue (“Cue on the Fly”)
• 4 different speed scan
• S/PDIF Digital Audio RCA Coaxial Output
• 30 Programmable Tracks
• Fader “Q” Start Control (a)
• Bop Effect (b)
• Flip-Flop (Relay Playback) (c)
• Sleep Mode (e)
• Selectable Pitch: +/-8%, +/-12% or +/-16%
• Seamless Loop - Uninterrupted Loop Playback
• Large bright LCD Screen can be viewed from
wide angles.
• 60 Second Transport Protection (d)
• Memory Backup, Defaults to last setting (f)
• Jog Wheel Pitch Bend +/-16% (g)
• Pitch Display
• Single/Continuous/Repeat Play Modes
• 1/75 Frame Search
• Instant Start within 10 msec (sound is produced immediately when the PLAY button is pressed)
(a) FADER “Q” START CONTROL: This feature is used in conjunction with American Audio® mixers that also
feature “Fader Q Start” control. For best results use this feature with two PRO-DJ2FX players. Connect your
PRO-DJ2FX’s as described in the set-up section of this manual. After set-up is completed load your unit's. By
moving the mixer’s crossfader from left to right you can start and pause your PRO-DJ2FX playback functions.
For Example, when using two PRO-DJ2FX units and a Fader “Q” Start mixer, if your mixer’s crossfader is all
the way to the left (player one is playing, player two is in cue or pause mode), and you move the fader at
least 20% to the right, player two will begin to play and player one will return to cue mode. When the crossfader
is to the right, and you move it 20% to the left, player one (will begin to play and player two will return to its’
cue point. You can create great effects similar to scratching with this feature. After storing cue points on each
side of the CD player, different songs or samples may quickly be recalled by moving the mixer crossfader
back and forth. New cue points can be easily selected on the PRO-DJ2FX player (see setting cue points
page 13). “Q” Start control is easy to use and mastering this feature will help you create amazing effects
with your music. Note: For proper “Q” Start operation be sure your mixers “Hamster” setting are set to
1/2 (Normal Setting).
(b) BOP EFFECT: The Bop Effect button serves two features. First, it is a stutter effect, creating a sound
similar to a sampler. Second, it will return to the last Cue point in memory instantly. This will allow you to create
great effects. To create the BOP Effect, see BOP Effect on page 22.
(c) FLIP-FLOP: This feature is used in conjunction with American Audio® mixers that also feature Fader “Q”
Start. For FLIP-FLOP results you must use two PRO-DJ2FX players. Connect your PRO-DJ2FX’s as
described in the set-up section of this manual. This feature will start the next player once one player has
ended. For example, if player one is playing a disc and it ends, player two will instantly begin to play.
You may set FLIP-FLOP to play track to track or disc to disc. For more information on this feature, see
FLIP-FLOP™ on page 23.
(d) 60 SECOND TRANSPORT PROTECTION: The CD transport tray will automatically close if left open for
more than 60 seconds. If a CD is left in the tray it will immediately cue.
(e) SLEEP MODE: The PRO-DJ2FX’s laser and pick-up assembly will power down after 15 minutes of
inactivity (when in pause or cue mode). This will lengthen the life of your motor drive and laser. To initialize
the player, just press the cue or play buttons.
(f) MEMORY BACKUP: The PRO-DJ2FX has a five year memory back-up, that will save your setting in
case the power supply is accidentally disconnected. PRO-DJ2FX will automatically remember your last setting
(repeat, SGL, CTN) even if you disconnect your main power.. The PRO-DJ2FX will store your cue points
in memory if you accidentally open transport tray or shut off the power. Note: Memory cues are erased
automatically when a new CD is played, or by holding memory button down for 5 seconds.
(g) JOG WHEEL PITCH BEND: During normal playback, the inner jog wheel acts as a momentary pitch bend.
Turing the wheel in a clockwise direction will increase the speed and turning the wheel in a counter-clockwise
direction will decrease the speed.
©American Audio®
-
-
PRO-DJ2FX™ Instruction Manual Page 7
GENERAL FUNCTIONS AND CONTROLS
1 2 3 4 5
6
7
8
9
Figure 3
Figure 4
28
27
26
25
10
11
29 30
31 32 33
34
Figure 5
24
23
22
12
13
21
14
15 16
17 18 19 20
A. TOP UNIT CONTROLS (FIGURE 3)
COAST effect is selected. See Coast effect on
page 24.
1. SKID - This button activates the SKID effect.
This effect simulates the sudden platter stop of
a turntable. Almost like pressing the stop button
on a turntable. When the SKID effect is selected
a number 1 will appear in the LCD (13), this
indicates the SKID effect is active. See "Skid"
effect on page 24.
3. REV/PLAY - This button activates reverse
play mode. When this effect is selected the disc
will begin to play in reverse mode, and continue
to play in reverse until reverse play function is
turned off. If reverse play is not turned off the disc
will continue to play in reverse until it returns to
the beginning of the disc. When the REV/PLAY
effect is selected a number 3 will appear in the
LCD (13), indicating REV/PLAY is active. See
reverse play on page 22.
2. COAST - This button activates the COAST
effect. This effect will simulates turning the power
off on a turntable, a turntable platter spinning
until it slowly loses momentum and stops. When
the COAST effect is selected a number 2 will
appear in the LCD (13), this will indicates the
4. P.S. - (Pitch Select Button) This button chang-
©American Audio®
-
-
PRO-DJ2FX™ Instruction Manual Page 8
GENERAL FUNCTIONS AND CONTROLS (Cont.)
es the pitch value. The pitch percentage can by 1 Icon (52) will appear in the LCD (13).
be changed between 8%, 12%, and 16%. 8%
10. CUE MEMORY - This button allows you to
will allow the least amount of pitch manipulation
program up to 4 cue points on the CD. For more
and 16% will allow the most amount of pitch
information on setting a cue point see page 18.
manipulation. To adjust to the different values tap
11. SKID/COAST/ADJUST - This button allow
you to change the Skid and Coast values. With
the SKID/COAST/ADJUST button selected (on)
the SKID value is one second and the COAST
value is five seconds. With the SKID/COAST/
ADJUST deselected (off) the SKID value is a 1/2
second and the COAST value is three seconds.
A yellow LED will indicated on and off functions.
this button. The LED next to the Pitch Button
(27) will indicate which pitch percentage mode is
activated by, flashing red for 8%, glowing green
for 12%, or glowing red for 16%. Note, the Pitch
Button (27) must be activated to get a LED read-
ing. The pitch values will immediately reflect the
amount of pitch being applied to a music source
in the CD drive. The pitch value is adjusted by
sliding the PITCH SLIDER (21) up and down.
12. OPEN/CLOSE (Disc Tray Open/Close) -
This button is used to open and close the
disc transport tray door. NOTE: When a disc is
loaded, the tray will not open unless the unit is in
pause or cue mode.
5. TIME - The TIME button is used to changed
the displayed time values. Time can be displayed
as elapsed track time, remaining track time, and
total disc remaining time.
13. LIQUID CRYSTAL DISPLAY (LCD) - This
high quality LCD Indicates all the functions (play,
pause, cue, etc...,), as they occur. This display
is viewable at several comfortable angles as
described on page 12. The LCD icons will be
described in the next section.
6. CUE BUTTONS - These button are used to
store four user programmable “Cue Points.” A
“Cue Point” is a starting point anywhere on a
disc. To program a “Cue Point” see Cue Points
on page 18.
7. BOP - This button is used to activate the
BOP Effect. A Bop Effect is a stutter, creating
a sound similar to a CD skipping. This function
will instantly play the last set cue point during
playback without music interruption. The Bop
Effect can be created in 2 ways. See creating a
BOP on page 22.
14. JOG WHEEL - (INNER WHEEL) This jog
wheel serves two functions depending on the
current operating mode:
A. The jog wheel will act as a slow frame
search control when the unit is in pause or
cue mode allowing you to set a specific cue
point or find a particular starting point.
B. The inner wheel also works as a momentary
pitch bend during playback. Turning the wheel
clockwise will increase the pitch percentage
up to 16%, and turning the wheel in the
counterclockwise direction will decrease the
pitch percentage up to -16%. The pitch bend
will be determined on how fast you turn the
wheel.
8. PROG. - (PROGRAM BUTTON) This button
is used to enter Program Mode. The word
“PROGRAM” will be indicated in the LCD Display
(13) when Program Mode is activated. For pro-
gramming information see “Programming” on
page 21.
9. REPEAT - This button activates the repeat
function. Pressing the Repeat Button once will
activate the track repeat function, pressing the
Repeat Button again will activate the disc repeat
function, pressing the Repeat Button once again
will turn off the repeat function. When the unit is
in disc repeat mode, the Repeat Icon (53) will
display in the LCD (13). When the track repeat
function is active the Repeat Icon (53) followed
15. SHUTTLE WHEEL - (OUTER RING) This
wheel has two forward and two reverse speed
positions for speed searching through tracks.
The more you turn the wheel in either direction,
the faster you search.
©American Audio®
-
-
PRO-DJ2FX™ Instruction Manual Page 9
GENERAL FUNCTIONS AND CONTROLS (Cont.)
16.
TRACK BUTTON - This buttons is the LCD (13). Use this slider to match the BPM’s
used to select a track. Tapping this button will of this unit to that of another music source. By
back-skip to the previous track, holding down this changing the pitch of one disc with respect to the
button will rapidly back-skip through the tracks other in this way, the beats can be matched.
on a CD.
22. RELOOP BUTTON - If a Loop has been
17. CUE - Pressing the CUE button during play- made (see setting a Seamless Loop on page
back immediately pauses playback and returns 23), but the unit is not actively in Loop mode
the track to the last set cue point (see setting a (a loop is not playing), pressing the RELOOP
CUE POINT, page 18). The red CUE LED will BUTTON will instantly reactivate Loop mode. To
glow when the unit is in cue mode The LED exit the Loop , press the OUT/EXIT BUTTON
will also flash every time a new CUE POINT (23). LOOP (48) and RELOOP (47) will display
is set. The CUE button can be held down to in the LCD (13) when the Reloop function is
momentarily play the CD. When you release the available.
CUE button it instantly returns to the last set
23. OUT/EXIT - This button serves two functions.
CUE POINT. You can also tap the CUE button
This button is used to set the ending point of
to create a BOP EFFECT (for definition of BOP
a loop. During normal loop playback, a loop is
exited by pressing the OUT/EXIT button.
EFFECT, see page 22).
18.
TRACK BUTTON - This buttons is
24. IN REALTIME CUE (SEAMLESS LOOP IN
BUTTON) - “CUE ON THE FLY” - This button
allows you to set a CUE POINT (see CUE POINT
page 18) without music interruption (“on the fly”).
This button also sets the starting point of a loop
used to select your desired track. Tapping this
button will forward skip to the next track, holding
down this button will rapidly forward skip through
the tracks on your CD.
19. PLAY/PAUSE BUTTON - Each press of the (see SEAMLESS LOOP on page 19).
PLAY/PAUSE BUTTON causes the operation to
change from play to pause or from pause to
25. (+) & (-) PITCH BEND -
A. (+) PITCH BEND - The (+) pitch bend function
creates a momentary “BUMP” in the CD’s
pitch speed (Beats per minute - BPM) when
the PITCH (27) function is activated. This
functions allows the beats between two CD’s
or any other music source to match. This
is a momentary function. When the button
is depressed the pitch speed will automati-
cally return to PITCH SLIDER'S (21) selected
pitch. Holding down this button will give a
maximum of +16% pitch. Be sure to remem-
ber that this function is a momentary pitch
adjustment, for a more precise adjustment
use the PITCH SLIDER'S (21) to match the
BPM’s with another playing music source.
play. While in play mode the green play LED will
glow, and while in pause mode the green play
LED will flash.
20. +10 BUTTON - This button is used to quickly
advance ten tracks. For example if you are
on track two, pressing the +10 BUTTON will
immediately advance you to track 12.
21. PITCH SLIDER - This slider is used to adjust
the playback pitch percentage when the PITCH
(27) function is activated. The slider is a set
adjustment and will remain set until the pitch
slider is moved or the PITCH (27) function has
been turned off. This adjustment can be made
with or without a CD in the drive. The pitch
adjustment will remain even if a disc has been B. (-) PITCH BEND BUTTON - The (-) pitch bend
remove, and will reflect on any other disc loaded
into the unit. That is to say, if you set a +2%
pitch on one disc, remove that disc and insert
another, that disc too will have a +2% pitch. The
amount of pitch being applied will be displayed in
function creates a momentary “Slow Down” in
the CD’s pitch speed (Beats per minute -
BPM) when the PITCH (27) function is acti-
vated. This functions allows the beats between
two CD’s or any other music source to match.
PRO-DJ2FX™ Instruction Manual Page 10
©American Audio®
-
-
GENERAL FUNCTIONS AND CONTROLS (Cont.)
This is a momentary function. When the ized power cord. Use of any other power may
button is depressed the pitch speed will result in sever damage to the unit. Be sure the
automatically return to PITCH SLIDER'S (21) local power matches the unit’s required power.
selected pitch. Holding down this button will
30. POWER SWITCH - This switch is used to
give a maximum of -16% pitch. Be sure to
control the unit's main power.
remember that this function is a momentary
31. VOLTAGE SELECTOR - Because power
supplies vary from location to location a voltage
selector switch has been incorporated in the
unit's design. This switch can select a voltage
input of 120v or 220v to accommodate the
two major power source. Always be sure to
disconnect the power plug before changing the
voltage.
pitch adjust-ment, for a more precise adjust-
ment use the PITCH SLIDER'S (21) to
match the BPM’s with another playing music
source.
26. SGL/CTN - This button allows the unit's play
mode to change between Single and Continuous.
In single mode the unit will play a single track
and return to cue mode. In continuous mode the
unit continues to play track by track and returns
to cue mode after all tracks have played. This
function also operates in PROGRAM and FLIP
FLOP modes. In program mode the continuous
function will play all tracks in a program, than
return to cue mode on the first track in the
program. When using two units in Flip-Flop
mode, each unit may be set up to run in either
single or continuous. In single mode a unit will
play a single track and jump to the next unit.
If the next unit is in continuous mode, that unit
will play all tracks and jump back to next unit,
and so on.
32. CONTROL - These control jacks are only
used for the "Q" function. Only use these jacks in
conjunction with a compatible "Q" seriesAmerican
Audio® mixer or CD unit. Connect the supplied
mini-plug from the CONTROL jack on the rear
of your unit to the control jack on a compatible
mixer or CD unit.
33. DIGITAL OUT - This jack sends a digital
stereo out signal. Use this connection to create
near perfect copies of your disc to a Mini disc,
CD-R, or any other recording device with a digital
input.
34. AUDIO OUT R & L - These jacks send a
left and right analog mono output signal. Use
these jacks to send standard audio to a mixer
or receiver.
27. PITCH BUTTON - This button is used to
turn the pitch function on and off. The pitch
functions of the PITCH SLIDER (21), PITCH
BEND BUTTONS (25) and JOG WHEEL (14) will
not function without this function being activated.
The pitch percentage value can be changed from
(+/- 8%), (+/- 12%) or (+/- 16%). The PITCH
BUTTON’s LED will indicate the maximum pitch
value by flashing red for 8%, glowing green for
12%, or glowing red for 16%.
28.TRANSPORT TRAY - This tray is used to
load and load compact disc. The tray is opened
and closed by pressing the OPEN/CLOSE BUT-
TON (12). Never attempt to force the transport
tray open or closed when the power is turned
off.
29. POWER CONNECTOR - This is the main
power connection. Only use the supplied polar-
©American Audio®
-
-
PRO-DJ2FX™ Instruction Manual Page 11
LIQUID CRYSTAL DISPLAY (LCD)
LCD DISPLAY
53 52
51
50
49
48
35
36
37
47
46
38
s
39
40
41
42
43
44
45
Figure 6
44). When the ELAPSE indicator is displayed in
the LCD, the time defined will refer to a single
track's elapsed time. The time mode is changed
by the tapping on the TIME BUTTON (5).
B. LCD DISPLAY (FIGURE 6)
35. FUNCTION INDICATORS - These indicators
serve two functions; Indicators 1-3 detail which
effect is active, Indicators 6-9 detail a cue point
stored in memory.
42. MINUTES METER - This meter will display
the elapse, total, or remaining time in minutes.
The display time will be indirect reference to the
current time mode.
36. CUE INDICATOR - This indicator will glow
when the unit is in CUE mode and will flash every
time a new CUE POINT is recorded in memory
(see setting CUE POINTS on page 18).
43. SECONDS METER - This meter will display
the elapse, total, or remaining time in seconds.
The display time will be indirect reference to the
current time mode.
37. PROGRAM INDICATOR - This icon indicates
"Program Mode" is activated. See Program Play
on page for more information on programing.
44. FRAME METER - This meter will display the
elapse, total, or frames. The displayed frames will
be indirect reference to the current time mode.
38. PLAY INDICATOR - This indicator will glow
when the unit is in play mode.
39. PAUSE INDICATOR - This indicator will glow
when the unit is in pause or cue mode.
45. PITCH METER - This meter displays the
pitch percentage being applied to playback by
the PITCH SLIDER (21). If the meter read zero
regardless of the PITCH SLIDER'S (21) position,
the PITCH (27) function is not activated.
40.TRACK INDICATOR - This double digit
indicator details a current track. The number
displayed in the track indicator is a direct refer-
ence to a track being selected for programming
or a track in play, pause, or cue mode.
46.TIME BAR INDICATOR - This bar visually
details the time defined in the TIME METER (42,
43, & 44). As with the TIME METER (42, 43, &
44), this bar is also dependent on the selected
41.ELAPSE INDICATOR - This indicator is in
direct reference to the TIME METER (42, 43, &
©American Audio®
-
-
PRO-DJ2FX™ Instruction Manual Page 12
LIQUID CRYSTAL DISPLAY (LCD) CONT.
time function (TOTAL REMAIN (50), REMAIN icon will display in the LCD. When the repeat
(47) OR ELAPSE (41). This bar will begin to function is first activated, the unit enters a repeat
flash when 15 seconds of a track remain and will track mode. This function is indicated by the
begin to rapidly flash when three seconds of a REPEAT and 1 (52) icons in the LCD. Tapping
track remain. The flashing bar is a great visual on the REPEAT (9) button once more will activate
reminder a track is about to end. The flashing the repeat disc option. This function will repeat
bar will function regardless of which time mode the entire disc over and over until the repeat
the unit is in.
function is disengaged. The repeat disc function
is indicated by the REPEAT icon displayed in the
LCD without the 1 icon.
47. REMAIN INDICATOR - This indicator is in
direct reference to the TIME METER (42, 43, &
43). When the REMAIN indicator is displayed in
the LCD, the time defined will refer to a single
track's remaining time. The time mode is changed
by tapping on TIME BUTTON (5).
48. RELOOP INDICATOR - This icon will display
when a LOOP is engaged or is set and ready
to be engaged.
49. LOOP - This icon flashes when a loop is
engaged or displays when a loop is not engaged
but is set and ready to be engaged.
50. TOTAL REMAIN INDICATOR - This indicator
is in direct reference to the TIME METER (42,
43, & 43). When the TOTAL REMAIN indicator is
displayed in the LCD, the time defined will refer
to a disc's total remaining time. The time mode is
changed by tapping on TIME BUTTON (5).
51. SINGLE INDICATOR - This indicates the unit
is in single play mode, the unit will play a single
and return to CUE mode. If the single indicator
is not displayed the unit is in continuous mode.
In continuous mode the drive will play through all
the tracks on the disc. Once all the tracks have
ended the unit will return to cue mode.
52. 1 INDICATOR - This indicator is in direct
reference to the REPEAT (53) indicator and
REPEAT (9) function. When the repeat function
is first activated, the unit enters a repeat track
mode. This mode will repeat a single track over
and over until the repeat function is disengaged.
The single track repeat function is indicated by
the REPEAT (53) and 1 icons in the LCD.
53. REPEAT INDICATOR - This indicator is in
direct reference to the REPEAT (9) function.
When the repeat function is activated the REPEAT
©American Audio®
-
-
PRO-DJ2FX™ Instruction Manual Page 13
BASIC OPERATIONS
5 in. / 12cm disc
1. OPENING AND CLOSING THE DISC TRAY/LOADING DISCS
This is an electronic operation and can only work when the power is on. Press
the OPEN/CLOSE BUTTON (12) to open or close the disc tray. Pressing the
PLAY/PAUSE BUTTON (19), will also automatically close the tray if it is open and
immediately cue any CD that is in it. If the transport tray is left open for more than
60 seconds it will close automatically to prevent accidental damage to the transport.
Again if a CD is left in the transport tray it will immediately cue to the first
song. The disc trays cannot be opened during playback to prevent playback from
being interrupted if the OPEN/CLOSE BUTTON (12) is pressed accidentally. Stop
playback, then press the OPEN/CLOSE BUTTON (12).
2. LOADING DISCS
Figure 7
The PRO-DJ2FX can play both 3 inch (8 cm) and 5 inch (12 cm) compact discs
(CD’s). Odd shaped and oval CD’s are not compatible. When loading a CD into the
unit always hold the disc by its' edges and place it in the disc tray. Never touch
the signal surface (the glossy side). When using 5 inch/12 cm discs, place the disc
in the outer tray guides (figure 7), and when using 3 inch/8 cm discs, place them
securely in the inner guides (figure 8).
3 in. / 8cm disc
CAUTION:
• NEVER insert any foreign objects in the disc tray.
• NEVER attempt to insert more than one disc in the disc tray at a time. Doing
so may result in severe damage to the unit.
• NEVER force the transport tray open or closed when the power is off, as this
may result in malfunction and damage the transport system.
Figure 8
3. SELECTING TRACKS
Select a desired track by using either of the two TRACK BUTTONS (16 & 18). Tapping the TRACK BUTTONS
(16 & 18) once will select either a higher or lower track. You may hold down the TRACK BUTTONS (16 &
18) to change tracks continuously at a higher speed. If you are using the TRACK BUTTONS (16 & 18) to
select a new track during playback (a track already playing) the new track you selected will immediately begin
playback as soon as the search operation is completed.
4. STARTING PLAYBACK
Insert an audio CD as describe above (loading discs). Pressing the PLAY/PAUSE BUTTON (19) with
an audio CD inserted will immediately start playback. The PLAY INDICATOR (38) will glow as soon as
playback begins. The point at which playback starts (cue point) will automatically be stored in the memory
as the cue point. The unit will return to this cue point (the point at which playback started) when the
CUE BUTTON (17) is pressed.
5. STOPPING PLAYBACK
Stopping playback will not stop the drive mechanism, but merely pause or cue the track. There are two
ways to stop playback:
1) Press the PLAY/PAUSE BUTTON (19) during playback to pause at that point.
2) Press the CUE BUTTON (17) during playback to return the track to it’s last cue point.
6. PAUSING
Pausing temporarily stops playback. Pressing the PLAY/PAUSE BUTTON (19) changes the operating mode
between play and pause. The PAUSE INDICATOR (39) in the LCD (13) will glow when pause mode is
activated or when a track is in cue mode.
7. AUTO CUE
”Cueing” is the action of preparing for playback. When the unit is in cue mode the CUE INDICATOR (36) in
the LCD (13) will glow. The unit is designed to automatically cue at the first audible signal on the first of a
disc when a disc is inserted. If a track is selected before a disc is inserted, the unit will automatically cue to
the first audible signal for the selected track.
©American Audio®
-
-
PRO-DJ2FX™ Instruction Manual Page 14
BASIC OPERATIONS (CONT.)
8. FRAME SEARCH
This feature allows you to scroll through a track to set a cue, starting
sample, or loop point. To use the scroll function you must first be in Pause
Mode or Cue Mode. Once you are in Pause or Cue mode, use your finger
tip to turn the JOG WHEEL (14) to scroll through the track (figure 9).
Turning the wheel in a clockwise direction will advance the frame search
and turning the wheel in a counter-clockwise direction rewinds the frame
search. When you use the JOG WHEEL (14) the monitor (headphone level)
function allows you to here what you are scrolling through. Once you reach
your desired starting point you can set a cue (starting) point by pressing
the PLAY/PAUSE BUTTON (19) as in figure 9. Pressing the CUE BUTTON
(17) will return the disc to the cue point just set.
Figure 9
9. SCANNING (FAST FORWARD / FAST REVERSE)
This function gives you a fast search through a disk or track. To
do this turn SHUTTLE WHEEL (15) in clockwise direction for fast
forward or counterclockwise for fast reverse. You can scan in 6
different forward and 6 different reverse speeds depending on how
much you rotate the wheel.
Figure 10
9. CHANGING THE TIME DISPLAY (42, 43, & 44)/TIME BAR (46):
The time may be displayed in three different modes; Elapsed, Remain, and Total Remain. During normal
playback, pressing the TIME BUTTON (5) as in figure 11, will change the time display information (42, 43, 44,
& 46) in the LCD. The following is a break down of the time settings and their definitions:
1) ELAPSED (41) - This details the time in the LCD (42, 43, & 44) as the
current tracks’ elapsed running time. The elapsed function only details
a tracks elapsed time and not the entire disc.
2) REMAIN (47) - This details the time in the LCD (42, 43, & 44) as the
current tracks’ remaining running time.
3) TOTAL REMAIN (50) - This details the time in the LCD (42, 43, & 44)
as the total disc remaining time.
TIME BAR INDICATOR - The time bar in the LCD visually details the time
defined in the TIME METER (42, 43, & 44). This bar is also dependent
on the selected time function (TOTAL REMAIN (50), REMAIN (47) or
ELAPSE (41). This bar will begin to flash when 15 seconds of a track
remain and will begin to rapidly flash when three seconds of a
track remain. The flashing bar is a great visual reminder a track
is about to end. The flashing bar will function regardless of which
time mode the unit is in.
Figure 11
©American Audio®
-
-
PRO-DJ2FX™ Instruction Manual Page 15
BASIC OPERATIONS (CONT.)
10. PITCH ADJUSTMENTS:
This function will increase or decrease a tracks playback speed or "PITCH," this is not a momentary change
as in "PITCH BENDING" (see page 17). The maximum pitch bend percentage allowed is +/-16%. The PITCH
SLIDER (21) is used to decrease or increase the playback pitch. If the slider is move up (towards the top
of the unit) the pitch will decrease, if the slider is moved down (towards the bottom of the unit) the pitch
will increase. The PITCH SLIDER (21) adjustment can be changed to range from +/-8%, +/-12%, or +/-16%
(See changing "PITCH SLIDER PERCENTAGE RANGE" figure 19/page 18). The pitch adjustments will effect
playback, reverse playback, and loops.
Activating the Pitch Slider (21): To activate the PITCH SLIDER (21), turn
the pitch function on. Press the PITCH BUTTON (27) to turn on the pitch
function, when the pitch function is activated a LED will begin to glow (or flash
depending on what pitch percentage value is selected, see changing pitch
values on page 18). If the pitch function is not activated neither the PITCH
SLIDER (21) nor the PITCH BEND BUTTONS (25) will not function.
Figure 12
Using the Pitch Slider (21): To use the PITCH SLIDER (21) slide the
slider up and down. Down will increase the pitch and up will decrease
the pitch. When the slider is in the center position, a green LED just
left of the slider will glow. When this slider LED is glowing there is zero
pitch being applied to a track.
Figure 13
Adjusting the Pitch Slider's Range (21): You may change the PITCH
SLIDER'S (21) operating range. To change the operating range be sure
the pitch function is turned on, see figure 17. The pitch percentage can be
changed between +/-8%, +/-12%, and +/-16%. +/-8% will allow the least
amount of pitch manipulation and +/-16% will allow the most amount of pitch
manipulation. To adjust to the different values tap the P.S. BUTTON (4). The
LED beside the PITCH BUTTON (27) will indicate which pitch percentage
mode the unit is operating in. Glowing green for +/-8%, glowing orange for
+/-12%, or glowing red for +/-16%. Note, the pitch function must be activated
to receive a LED reading.
Figure 14
©American Audio®
-
-
PRO-DJ2FX™ Instruction Manual Page 16
BASIC OPERATIONS (CONT.)
11. PITCH BEND:
This function will momentarily increase or decrease a tracks playback speed. There are two ways to operate
this function with the (-) & (+) PITCH BUTTONS (25) or with the JOG WHEEL (14). The maximum pitch bend
percentage allowed is +/- 16%. The pitch bend function will work in conjunction with the PITCH SLIDER
(21) pitch setting. The PITCH SLIDER (21) adjustment can be changed to range from +/-8%, +/-12%, or
+/-16% (See changing "PITCH SLIDER PERCENTAGE RANGE" on page 16). For example, if the PITCH
SLIDER (21) is set to a 2% pitch gain the pitch bending process will begin at 2% and will continue to
the maximum of -/+16%.
PITCH BEND BUTTONS (25):
The (+) PITCH BEND BUTTON (25) will provide a speed bump and the (-) PITCH BEND BUTTON (25) will
provide a slow down. The extent to which the speed changes is proportionate to the amount of time the button
is pressed. For example, if the (+) PITCH BEND BUTTON (25) is held down continuously, the disc speed will
increases and will continue to increase until reaches a maximum of 100% speed gain. When you release the
(+) PITCH BEND BUTTON (25) the disc speed will automatially return to it’s previous speed.
c
Holding down or tapping on the
(+) PITCH BEND BUTTON (25)
will provide a speed bump in the
playback pitch.
Holding down or tapping on the
(-) PITCH BEND BUTTON (25)
will provide a slow down in the
playback pitch.
Figure 15
Figure 16
JOG WHEEL (14):
The JOG WHEEL (14) will temporarily bend the pitch if a track is in
play mode Rotating the wheel in a clockwise direction will increase
your track pitch and rotating the wheel in a counter-clockwise direction
will slow your track pitch. The speed you rotate the JOG WHEEL (14)
will determine pitch bend percentage (%).
Figure 17
©American Audio®
-
-
PRO-DJ2FX™ Instruction Manual Page 17
BASIC OPERATIONS (CONT.)
12. SETTING and STORING a CUE POINT:
Setting A Cue Point:
A cue point is the exact point playback will begin when the PLAY/PAUSE BUTTON (19) is pressed. A cue point
may be anywhere on a disc or in a track. You may set and store up to five independent cue points per disk.
Four cue points are stored in the CUE BUTTONS (6) and one in the IN REALTIME CUE BUTTON (24). Once
a cue point is set it may be recalled at any time during normal playback. Figures 18 and 19 will detail the
procedures for setting your custom cue points. There are two ways to set a CUE point:
1) Press the IN REALTIME CUE BUTTON (24) on the fly (while a disc is
playing). This will set a CUE Point without music interruption. Once this point
is set, you may return to this point at any time by pressing either the CUE
BUTTON (17) or the BOP BUTTON (7). Pressing the CUE BUTTON (17) will
stop playback and return the disc in cue mode, pressing the BOP BUTTON
(7) will return the disc to cue point without music interruption and continue
playback from that point.
Figure 18
2) The JOG WHEEL (14) may be used to set a cue point by frame.
While a disc is in pause or cue mode, use the JOG WHEEL (14) to
scroll through a track to find your desired starting point. Once you
have found your desired cue point press the PLAY BUTTON (19) to
enter this point in to the unit's memory. At this point pressing either
the CUE BUTTON (17) or the BOP BUTTON (7) will return you to this
exact point.
Figure 19
Storing A Cue Point: Once you have set a cue point by one of the two means as detailed above, you may
store this point in any one of the CUE BUTTONS (6). Once a cue point is stored in to memory it may be
recalled at any time by pressing the cue button it was stored into. A cue point may even be recall if the disc
has been remove or power had been disconnected. To Store a cue point:
1) Create a cue point, press the CUE MEMORY BUTTON (10), as in
Figure 20. The yellow Cue Memory LED will glow. This indicates a
cue point is ready to be stored in to memory.
Figure 20
American Audio® • PRO-DJ2FX™ INSTRUCTION MANUAL • PAGE 18
BASIC OPERATIONS (CONT.)
2) At this point pressing any one of the four CUE BUTTONS
(6) will store your cue point into memory (Figure 21), and the
yellow Cue Memory LED will shut off.
3) Repeat steps one and two to store up to four Cue Points.
Once all your four cue points have been stored you may
access them at any time.
4) During playback the cue points will instantly start without any
music interruption. During play or pause mode accessing a
stored cue point will cue to that point in pause mode.
Figure 21
13. CREATING AND PLAYING A SEAMLESS LOOP
A seamless loop is a sound loop that plays continuously without sound interruption. You can use this loop to
create dramatic effect in your mixing. This loop has no time limit and you could actually loop the entire length
of disc. You create a seamless loop between two continuous points of a disc. The following steps illustrate
the procedures for creating a seamless loop:
1) Press the PLAY/PAUSE BUTTON (19) to activate
playback mode.
Figure 22
2) Press the IN REALTIME CUE BUTTON (24). This will set a
loops starting point. The IN REALTIME CUE BUTTON (24) LED
will briefly indicating a starting point has been set.
Figure 23
American Audio® • PRO-DJ2FX™ INSTRUCTION MANUAL • PAGE 19
BASIC OPERATIONS (CONT.)
3) Press the OUT/EXIT BUTTON (23) to set the ending point for your
SEAMLESS LOOP (Figure 13). The IN REALTIME CUE BUTTON (24) and
OUT/EXIT BUTTON (23) LEDs will begin to flash indicating SEAMLESS
LOOP mode has been activated.
LOOP INDICATORS - During a seamless loop, the LOOP (49) and RELOOP
(48) INDICATORS will light in the LCD (13) indication a loop is active.
Figure 24
EXITING A LOOP - To exit a SEAMLESS LOOP, press the OUT/EXIT
BUTTON (23). The IN REALTIME CUE BUTTON (24) and OUT/EXIT
BUTTON (23) LEDs will remain on, but will stop flashing. Music playback
will resume normal play (Figure 25). The IN REALTIME CUE BUTTON (24)
and OUT/EXIT BUTTON (23) LEDs will remain on to remind you that a
loop is stored in memory.
Figure 25
REPLAY LOOP - The RELOOP (19) function allows you to return to your
stored loop at any time. The IN REALTIME CUE BUTTON (24) and OUT/EXIT
BUTTON (23) LEDs will indicate a loop is stored in memory, and may be played
at any time. To replay the loop, press the RELOOP BUTTON (19). The IN
REALTIME CUE BUTTON (24) and OUT/EXIT BUTTON (23) LEDs will again
begin to flash indicating SEAMLESS LOOP mode has been activated (Figure
26) and your stored loop will immediately begin to play.
Figure 26
14. EDITING A LOOP:
Please note only the ending point of a loop may be edited, a loop may be made shorter or longer. Before
you can edit your seamless loop you obviously must first have created a seamless loop to edit. If you haven’t
created a SEAMLESS LOOP, follow the instructions in step 10. If a SEAMLESS LOOP has already been
created, press the RELOOP BUTTON (22) to activate your SEAMLESS LOOP (Figure 26), if it is not already
playing. To edit a loop’s ending point:
1) Press the OUT/EXIT BUTTON (23) to return to normal play from the loops cue point (Figure 25). This will
disengage the SEAMLESS LOOP and allows you to edit the loops ending point.
2) Press the OUT/EXIT BUTTON (23) again when you reach your new ending point (Figure 25).
- FOR A SHORTER LOOP: Press the OUT/EXIT BUTTON (23) at sooner point in the track (Figure 25).
- FOR LONGER LOOP: Press the OUT/EXIT BUTTON (23) at later point in the track (Figure 25).
American Audio® • PRO-DJ2FX™ INSTRUCTION MANUAL • PAGE 20
BASIC OPERATIONS (CONT.)
15. PROGRAM PLAY
This operation allows you to customize your disc playback. You may select specific tracks to played and the
order they will be played in. You may program a maximum of 20 tracks at once and program a single track to
played more than once. To create a program:
1) Be sure a disc is inserted in the drive and press the PROGRAM
BUTTON (8). Pressing the PROGRAM BUTTON (8) from any function will
immediately pause the disc and enter the program mode.
2) After activating the program mode the program indicator LED beside the
PROGRAM BUTTON (8) and the PROGRAM INDICATOR (37) in the LCD
(13) will begin to glow indicating Program Mode has been activated.
Figure 27
3) Select a track to be programmed by using the
FORWARD TRACK SKIP (18) and BACK SKIP
TRACK BUTTON (16).
Figure 28
4) Once you reach the track you wish to place in to the program memory
pressing PROGRAM BUTTON (8) will lock the track into memory.
Figure 29
5) Repeat these steps three and four up to 29 times (up to 30 tracks may be programmed).
6) As you program tracks in memory the LCD (13) will indicate the tracks that have been programmed
in to memory.
7) When you have finished your programming and are ready to begin
playback simply press the PLAY/PAUSE BUTTON (19) and your
program will begin to play.
8) After you have complete your program you can always add more tracks
to your program by repeating the steps one through four. Remember
that you can only a maximum of 30 track in a program and you can
only add track not subtract.
9) To cancel and clear the program press and hold down the PROGRAM
BUTTON (8) for more than two seconds (see figure 29).
Figure 30
American Audio® • PRO-DJ2FX™ INSTRUCTION MANUAL • PAGE 21
ADVANCED OPERATIONS
Creating a BOP Effect:
The Bop Effect is a stutter effect that is similar to a CD skipping. You can use this effect to create tricks in your
mixing. Creating a BOP effect is a simple process:
1) Press the PLAY/PAUSE BUTTON
(19) so music is playing (Figure 31).
Figure 31
2) Press the IN BUTTON (12) at the point
you want your BOP to take place (Figure
32).
Figure 32
3) Now tap the BOP BUTTON (7). It will produce
a stutter effect as quickly as you tap on the
BOP BUTTON (7). See Figure 33.
Figure 33
Reverse Play:
Reverse play allows you to play a track, loop, or sample backwards. This function is activated by pressing the
REV/PLAY BUTTON (3) as in figure 34. This function will react differently to different playback modes:
- Reverse track/disc play. In this mode the unit will playback in reverse until
the reverse function is turned off. If the reverse function is not turned off the
unit will continue to play the remainder of the disc in reverse mode until it
reach the begging of the disc. When the unit comes to the beginning it will
automatically cue to the first track. If the unit is paused in this mode it will
continue to play in reverse when playback begins again.
- Reverse loop play. In this mode the loop will play in reverse once and
turn off. If the reverse function is turned off at this point, the loop will
continue in regular play. If the OUT/EXIT BUTTON (23) is pressed during
reverse loop playback mode, playback will continue in reverse until the
reverse function.
Figure 34
American Audio® • PRO-DJ2FX™ INSTRUCTION MANUAL • PAGE 22
ADVANCED OPERATIONS
FLIP-FLOP™
This feature is kind of “auto pilot." “Flip-Flop” mode can only function with the use of two PRO-DJ2FX
units. The “Flip-Flop” function may be used with or without an American Audio “Q” deck mixer, you can
have one unit begin playback when the other ends. You can “Flip Flop” single tracks, the entire disc,
a combination of the two, or you can even “Flip-Flop” your programmed tracks.
To FLIP-FLOP single tracks or programmed tracks:
1) Connect your system as described in the set up section on page 6.
2) Set your mixer’s crossfader to the center position.
3) Be sure your two units are single mode. SINGLE (51) should be indicated in the LCD (13).
4) Load your two PRO-DJ2FX with audio disc.
5) After they have both cued, press the PLAY/
PAUSE BUTTON (19) on one of your drive to
begin playback.
6) After the first unit’s single track has ended the
second unit’s track will immediately begin play-
back.
7) FLIP FLOP will continue until you stop it or power
is interrupted.
Figure 35
To FLIP-FLOP entire CDs:
To FLIP-FLOP an entire disc, be sure both drives are in continuous play mode. The SINGLE ICON
(51) should not be displayed in the LCD (13). When both drives are in continuous play mode, follow
the directions for single track FLIP-FLOP as detailed above. When one the disc in one unit ends the
other unit will immediately begin playback.
Combining FLIP-FLOP modes:
Flip-Flop modes may combined. One unit may run in single mode and the other in continuous mode.
When the units are arranged in this fashion, the unit in single mode will play a single track and flip to
the next unit. The next unit will then play the entire disc and flip back to the other. The other will then
play the next track and flip back to the other unit, and so on.
Fader Q-Start™
This function works in conjunction with a compatible American Audio “Q-Start" DJ mixer. When used
with a compatible CD player, you can use the crossfader to start and stop the CD Player with the slide
of the fader.
Connecting your PRO-DJ2FX to a Fader “Q” Start mixer for “Flip Flop” control: Be sure to
connect 1/8” mini plugs from the control connection on the rear your PRO-DJ2FX to the 1/8” control
jack on the rear of American DJ “Q” series mixer. That’s it, you’ll be set for FLIP FLOP!
American Audio® • PRO-DJ2FX™ INSTRUCTION MANUAL • PAGE 23
ADVANCED OPERATIONS
BUILT-IN EFFECTS: The PRO-DJ2FX™ comes with two built in effects. Only one effect may be
used at any given time. The Built-in effects include Skid and Coast. When either effect is activated a
corresponding icon will display in the LCD. For example when the SKID EFFECT (1) is activated a 1
(35) icon will display in the LCD (13). You can choose to use the effects with their default setting or
you may choose activate the SKID/COAST/ADJUST (11) function to increase the effect parameters
(see below). Each effect has two sets of parameters. All parameters will be reset to there default
values when power is shut off.
1. SKID - This button activates the SKID effect. This effect
simulates the sudden platter stop of a turntable. Almost like
pressing the stop button on a turntable.
SKID EFFECT: The Skid effect simulates the sudden platter stop of a
turntable, like pressing the stop button on a turntable. When the SKID
effect is selected the "SKID" icon displays in the LCD (13).
Figure 36
2. COAST - This button activates the COAST effect. This effect
will simulates turning the power off on a turntable, a turntable
platter spinning until it slowly loses momentum and stops.
COAST EFFECT: The COAST effect simulates a turntable slowly
revving up to it's proper speed, or slowly winding down to a stop, like
tuning the power off when a turntable is running. When the COAST
effect is selected the "COAST" icon displays in the LCD (13).
Figure 37
3. SKID/COAST/ADJUST - This button allow you to change the Skid
and Coast values. With the SKID/COAST/ADJUST button selected
(on) the SKID value is one second and the COAST value is five
seconds. With the SKID/COAST/ADJUST deselected (off) the SKID
value is a 1/2 second and the COAST value is three seconds. A yellow
LED will indicated on and off functions.
Figure 37
American Audio® • PRO-DJ2FX™ INSTRUCTION MANUAL • PAGE 24
BEFORE SWITCHING OFF THE POWER
• When you have finished using the CD unit, and before switching off the power, be sure that the disc holder
has been closed with the OPEN/CLOSE button (see figures 7 & 8).
• TRAY PROTECTION: If tray is not closed after 60 seconds, it will close automatically and pause.
CAUTION: DO NOT forcibly close the disc holder when the power is off.
DO NOT switch off the power when the disc holder is
open. Switch off the power after the disc holder has
been closed with the OPEN/CLOSE BUTTON (12).
COMPACT DISCS
1. PRECAUTIONS ON HANDLING COMPACT DISCS
Compact disc are constructed of the same types of plastic record are. To avoid severe damage to you valuable
disc please observe the following guide lines. Following the these guide lines will ensure long disc life.
•
•
Do not allow fingerprints, oil or dust to get on the surface of the disc. If the disc is dirty, wipe it off with a
soft dry cloth.
Do not use benzene, thinner, water, record spray, electrostatic-proof chemicals, or silicone-treated cloths
to clean discs.
•
•
•
•
•
•
Always handle discs carefully to prevent damaging the surface; in particular when removing a disc from its
Do not bend the disc.
Do not apply heat.
Do not enlarge the hole in the center of the disc.
Do not write on the label (printed side) with a hard tipped implement such as a pencil or ball point pen.
Condensation will form if a disc is brought into a warm area from a colder one, such as outdoors in
winter. Do not attempt to dry the disc with a hair dryer, etc.
2. PRECAUTION ON STORAGE
•
•
•
After playing a disc, always unload it from the unit.
Always store the compact disc in the jewel case, protecting from dirt or damage.
Do not place discs in the following areas:
a) Areas exposed to direct sunlight for a considerable time.
b) Areas subject to accumulation of dust or high humidity.
c) Areas affected by heat from indoor heaters, etc.
American Audio® • PRO-DJ2FX™ INSTRUCTION MANUAL • PAGE 25
WARRANTY
2-YEAR LIMITED WARRANTY
A. American Audio® hereby warrants, to the original purchaser, American Audio® products to be free
of manufacturing defects in material and workmanship for a period of 2 Year (730 days) from
the date of purchase. This warranty shall be valid only if the product is purchased within the
United States of America, including possessions and territories. It is the owner’s responsibility
to establish the date and place of purchase by acceptable evidence, at the time service is sought.
B. For warranty service, send the product only to the American Audio® factory. All shipping charges
must be pre-paid. If the requested repairs or service (including parts replacement) are within the
terms of this warranty, American Audio® will pay return shipping charges only to a designated point
within the United States. If the entire instrument is sent, it must be shipped in its original package.
No accessories should be shipped with the product. If any accessories are shipped with the prod-
uct, American Audio® shall have no liability whatsoever for loss of or damage to any such acces-
sories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified
in any manner which American Audio® concludes, after inspection, affects the reliability of the prod-
uct; if the product has been repaired or serviced by anyone other than the American Audio® factory
unless prior written authorization was issued to purchaser by American Audio®; if the product is
damaged because not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning or peri-
odic check-up. During the period specified above, American Audio® will replace defective parts at
its expense, and will absorb all expenses for warranty service and repair labor by reason of defects
in material or workmanship. The sole responsibility of American Audio® under this warranty shall
be limited to the repair of the product, or replacement thereof, including parts, at the sole discre-
tion of American Audio®. All products covered by this warranty were manufactured after January 1,
1990, and bear identifying marks to that effect.
E. American Audio® reserves the right to make changes in design and/or improvements upon its prod-
ucts without any obligation to include these changes in any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any accessory sup-
plied with products described above. Except to the extent prohibited by applicable law, all implied
warranties made by American Audio® in connection with this product, including warranties of
merchantability or fitness, are limited in duration to the warranty period set forth above. And no war-
ranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply
to this product after said period has expired. The consumer’s and or Dealer’s sole remedy shall
be such repair or replacement as is expressly provided above; and under no circumstances shall
American Audio® be liable for any loss or damage, direct or consequential, arising out of the use
of, or inability to use, this product.
G. This warranty is the only written warranty applicable to American Audio® Products and supersedes
all prior warranties and written descriptions of warranty terms and conditions heretofore published.
©American Audio®
-
-
PRO-DJ2FX™ Instruction Manual Page 26
SPECIFICATIONS
GENERAL
Model: American Audio® PRO-DJ2FX™ - Professional Compact Disc Player
System:
Single, Tray Loading, Digital Compact Disc Audio Player.
Disc type:
Standard compact discs (5 in / 12cm and 3in/8cm discs)
Dimensions:
3 1/4” ~ 4 1/2” H x 8 1/2” W x 10 3/8” L
Place on flat surface or mount in flat case
5.3 Lbs. / 2.4 kgs
AC 115v/230v, 50/60Hz
14W
+/-8%, +/-12%, +/-16%
+/-16%
Installation:
Weight:
Power supply:
Power consumption:
Pitch control range:
Pitch bend:
Pitch accuracy:
Environmental conditions:
+/- 0.1%
Operational temperature:
Operational humidity:
Storage temperature:
5 to 35˚C
(41 to 95˚F)
25 to 85% RH (non-condensation)
-20 to 60˚C (4 to 140˚F)
Accessories:
Dual RCA Cable (for left and right channels)
Control 1/8” miniplug type (3 feet)
AUDIO SECTION
Quantization:
Sampling rate:
16 bit linear per channel
44.1 kHz at normal pitch
8 times over sampling 1 bit D/A converter
16 bit
Over sampling rate:
D/A conversion
Frequency response:
Output level:
+/- 1 dB 20 Hz to 20,000 KHz
2.0V +/- 1dB
Load impedance:
47k ohm or more
AUDIO CHARACTERISTICS (TEST DISC: TCD-782, LOAD=47Kohm)
ITEM
NOMINAL
LIMIT
CONDITION
Output level
2.0Vrms+/-1dB
2.0V+/-1dB
1KHz,0dB
Channel balance
Frequency response
De-emphasis response
Channel separation*
T.H.D. + NOISE*
S/N ratio (IHF-A)*
0.5dB
1.0dB
1KHz,0dB
+/-0.5dB
+/-2.5dB
82dB
+/-1.0dB
+/-3dB
75dB
0.025%
75dB
20Hz-20KHz,0dB
16KHz, -20dB
1KHz,0dB
1KHz,0dB
1KHz.0dB
0.02%
84dB
NOTE: *With 20KHz low pass filter.
SEARCHING TIME (TEST DISC: TCD-792)
ITEM
NOMINAL
LIMITS
CONDITION
Short access time
Long access time
CD recover time
1.7 sec
4 sec
6 sec
2 sec
Play next track
Track 1 ->Track 20 / Track 20 ->Track 1
CD play interrupted by mechanical shock
3 sec
1 sec
PLAYABILITY
ITEM
NOMINAL
LIMIT
CONDITION
Interruption
1000um
1000um
75um
210um
1mm
700um
600um
65um
140um
0.54mm
TCD-725
Black dot
TCD-725
Finger prints
Eccentricity
Vertical deviation
TCD-725
TCD-712,713 NO TRACK JUMP
TCD-731R
PICK-UP
System
Object lens drive system
Tracking detection
Optical source
Wave length
Object lens drive system optical pick-up
2 dimensional parallel drive
3 spot beam detection
Semiconductor laser
780nm
NOTES:
The specifications are subject to change to any improvement by negotiations in advance.
The parts are subject to change to any improvement within the range of the specifications.
American Audio® • PRO-DJ2FX™ INSTRUCTION MANUAL • PAGE 27
©American Audio
A Division of the American DJ Group of Companies
American Audio World Headquarters:
4295 Charter Street
Los Angeles, CA 90058 USA
Tel: 323-582-2650 Fax: 323-582-2610
|