Vivitar DVR 380 User Manual

DVR 380  
Digital Camcorder  
with Camera  
User Manual  
© 2009-2011 Sakar International, Inc. All rights reserved.  
Windows and the Windows logo are registered trademarks of Microsoft Corporation.  
All other trademarks are the property of their respective companies.  
Introduction  
Thank you for purchasing this camcorder. Everything you need to take quality digital photos and  
videos is included with your digital video recorder.  
Vivitar makes capturing those special moments as easy as possible.  
Note: Your camcorder needs an SD Memory card (up to 16GB) for normal use.  
SD Memory cards are not included and need to be purchased separately.  
Please read this manual carefully first in order to get the most out of your digital video recorder.  
What’s Included  
1. Digital Camcorder  
2. Wrist Strap  
3. Vivitar Experience Image Manager  
software Installation CD  
4. Built-in USB Connector  
(not shown)  
Note: SD memory card and batteries not included.  
2
   
Parts of the Camcorder  
1. Power Button  
2. Shutter Button  
3. MODE Button  
10. LCD Screen  
11. Lens  
12. SD Memory Card Slot  
13. USB Lever  
4. SET (Menu/Delete) Button  
5. Up / Zoom In Button  
6. Down / Zoom Out Button  
7. Right Button  
14. USB Connector  
15. Microphone  
16. Speaker  
8. Left Button  
17. Wrist Strap Connector  
18. Battery Compartment  
9. LED Indicator  
3
   
Initial Camcorder Setup  
Installing the Batteries  
Installing the Memory Card  
Make sure the camcorder is  
powered OFF.  
Slide the battery cover off.  
Insert 3 X AAA (1.5V) batteries.  
Insert SD Memory card  
(up to 16GB) before use.  
Turning On the Camcorder  
Using the Camcorder  
4
When powering the camcorder ON for the first time the camcorder will take you through the  
initial setup.  
Powering the Digital Video Recorder ON  
1)  
Batteries  
Make sure the batteries have been inserted properly into your digital video recorder.  
Slide the battery cover on the back of the camera in a downward direction to open the cover.  
Insert 3 x AAA (1.5V) batteries (not included) with the correct polarity, according to the  
polarity illustrated inside the battery compartment.  
Note:  
Alkaline batteries are recommended.  
Remove the batteries from the camera when not in use for an extended period.  
Do not mix alkaline and non-alkaline batteries.  
Some camera features (Flash) will not work if the battery power level is low.  
When the battery power is low the battery icon turns red and the camcorder will  
automatically turn off a few seconds later.  
The energy status of the power is displayed on LCD as shown below:  
Full battery power  
Medium battery power  
Low battery power  
2)  
SD Memory Card  
Make sure the camcorder is powered OFF before inserting your SD/MMC/SDHC Memory  
Card.  
Make sure an SD card (up to16GB) has been inserted into your digital video recorder.  
(SD Memory card not included.)  
To properly insert the SD Card:  
Push the SD card into the slot in the direction shown on the camcorder (see SD icon by the  
SD card slot). Push the SD card until you hear a slight clicking sound. This indicates the SD  
card has been inserted correctly.  
Note:  
After the camcorder is powered on, an SD icon will appear on the LCD display. If you do  
not see the SD icon on the display, please check if the card was inserted properly.  
Make sure the SD card is not locked (check the lock switch on the side of the SD card). If the  
5
SD card is locked this will prevent the camcorder from saving captured photos to the SD  
card.  
3)  
Power On  
Press the POWER  
button to turn on the camcorder.  
Setting the Camcorder Language  
You will first be prompted to select a language for the camcorder. The Language selection menu  
will appear. Select the language of your choice and press the Shutter/OK button to confirm the  
selection.  
Your digital video recorder is now ready to begin capturing videos and photos.  
6
Main Camcorder Modes  
Your digital video recorder has different modes for the various camcorder functions.  
You can switch modes by pressing the MODE button on your digital video recorder after the  
camcorder has been powered ON.  
Video Capture Mode  
Use this mode to capture videos with your digital video recorder.  
This is the default mode when the camcorder is powered ON.  
To take a video, aim your camcorder as desired and press the Shutter button to start the  
record. A red record indicator will appear on the LCD screen while record is in progress. To  
stop the record, press the Shutter button again. The video will be automatically saved to  
your camcorder‟s memory card.  
To access the various menus for the Video Capture mode, press the SET button while in  
the Video Capture mode.  
Photo Capture Mode  
Use this mode to capture pictures with your camcorder.  
After turning on your camcorder, press the MODE button once to open the Photo Capture  
mode.  
To take a picture, aim your camcorder as desired and press the Shutter button.  
The picture will be automatically saved to your camcorder‟s memory card.  
To access the various menus for the Photo Capture mode, press the SET button while in  
the Photo Capture mode.  
Playback Mode (Photos & Videos)  
Use this mode to view and manage the photos and videos on your camcorder.  
After turning on your camcorder, press the MODE button twice to open the Playback mode  
for photos and videos. You can scroll through the photos and videos that you‟ve previously  
taken to view and delete them as desired.  
To access the various menus for the Playback mode for photos and videos, press the SET  
button while in the Playback mode.  
7
 
Camcorder Technical Specifications  
Image Sensor  
Image Resolution  
Video Resolution  
File Format  
CMOS Sensor  
1280x1024 pixels (1.3MP), 640x480 pixels (VGA)  
640X480pixels (VGA 30fps), 320X240pixels (QVGA 30 fps)  
JPEG/AVI  
SD/MMC/SDHC (up to 16GB) SD Card Memory Card not  
included  
External Memory  
LCD Display  
Lens  
1.77 Inch TFT  
f=3.8mm  
F2.8  
Zoom  
4X Digital Zoom  
Normal  
Auto  
Image Quality  
White Balance  
Color Effect  
Light Exposure  
ISO  
Standard  
Auto  
Auto  
Frequency  
Auto Power Off  
Metering  
60 Hz  
3 minutes  
Center  
Language  
Microphone  
Speaker  
English, French  
Yes  
Yes  
Interface  
USB 2.0 (HS)  
Window XP SP3 / Vista SP1/ Windows 7  
Mac OS X v10.5.x or higher  
System Requirements  
Battery  
3 x AAA (1.5V) Alkaline batteries  
Working Temperature  
0~40 C  
8
 
Computer System Requirements Windows  
To be able to download photos and videos to your PC, you will need the following minimum  
configuration:  
Microsoft® Windows XP with Service Pack 3, Windows Vista with Service Pack 1 or Windows 7  
Pentium® 4 processor (or above)  
512 MB of RAM, with 250 MB of free hard disk spaceꢀ  
16-bit Color monitor, 1024 X 768 recommended screen resolutionꢀ  
CD-ROM Drive  
QuickTime® 6 or higherꢀ  
Microsoft® Internet Explorer 7 or higher  
Windows Media Player 10 or higherꢀ  
DirectX 9 or higher  
Internet connection required  
Computer System Requirements Macintosh  
To be able to download photos and videos to your Macintosh, you will need the following  
minimum configuration:  
Intel processor running Mac OS X v10.5.x or later  
256 MB RAM, 250 MB free hard disk space  
Display: 1024 x 768 or higher-resolution monitor  
CD-ROM Drive  
QuickTime® 6 or higher  
Internet connection required  
9
   
Powering ON/OFF Your Digital Video Recorder  
Make sure the batteries have been inserted properly into your digital video recorder.  
If your camcorder comes with a rechargeable lithium battery, make sure it is fully charged  
before the first use.  
Make sure an SD card has been inserted into your camcorder.  
(SD card up to 16GB - SD Card not included)  
Powering the camcorder ON  
Press the Power  
button to turn your camcorder ON.  
The camcorder will be in Video Capture mode to start.  
Powering the camcorder OFF  
While the camcorder is on, you can press the Power  
button again at any point to turn your  
camcorder OFF. You will see a “Goodbye” splash screen and then the camcorder will power off  
completely.  
Note: When there is insufficient battery power, a Low Batterymessage will appear on the LCD  
screen. The digital video recorder will automatically power off a few moments later.  
Auto Power Saving  
Your digital video recorder has an Auto Power Off feature that will automatically turn off the  
camcorder if it has not been in use after 3 minutes.  
10  
 
Changing Camcorder Mode  
Your digital video recorder has three main modes:  
1) Video Capture Mode - Use this mode to capture videos with your camcorder.  
2) Photo Capture Mode - Use this mode to capture photos with your camcorder.  
3) Playback Mode (for photos and videos) - Use this mode to view the photos and videos  
you have already taken with your camcorder.  
When the camcorder is first powered ON, the Video Capture Mode will be active. The icons that  
appear on the LCD screen are the best default settings so that you can begin to capture and  
enjoy clear quality videos and photos.  
To change the active camcorder mode, make sure the camcorder is powered ON and press the  
MODE button.  
When in Video Capture Mode, this icon will display on the top-left corner of the LCD display  
When in Photo Capture Mode, this icon will display on the top-left corner of the LCD display  
When in Playback Mode, this icon will display on the top-left corner of the LCD display  
11  
 
Navigating the Menus  
Each camcorder mode has a set of menus specific to that mode.  
1) Press the SET button to open the menus for the current mode.  
1) Press the LEFT or RIGHT direction control buttons to scroll between the various menus for  
the current mode.  
2) Press the UP or DOWN direction control buttons to highlight the desired menu selection.  
3) Press the Shutter/OK button to confirm and select the highlighted menu option.  
4) If the selection can be remembered by the camcorder, a  
selection icon will appear to the  
right of the selected menu option. Changes made to these options will remain as is until you  
decide to change them again at a later time.  
5) Some menu options are single-use functions that are not remembered by the camcorder  
and do not display this icon when selected.  
6) At any time you can press the SET button to exit the menus and return to the previous  
screen.  
12  
 
Video Capture Mode  
The Video Capture Mode allows you to capture videos with your digital video recorder. When the  
camcorder is first powered ON, the Video Capture Mode will display by default.  
Taking a Video  
1) While in Video Capture Mode use the LCD display to direct the camcorder at the scene you  
would like to capture.  
2) Press the UP - Zoom In and Down - Zoom Out buttons to better set the camcorder display  
if desired.  
3) Press the Shutter button to start the video capture.  
4) The elapsed time will begin to appear on the top right corner of the LCD screen and a red  
indicator will appear in place of the video icon on the screen.  
5) To stop the video record, press the Shutter button again.  
6) The video will automatically be saved to the camcorder‟s SD card.  
Note: The amount of recording time available for the resolution selected appears on the top  
center of LCD screen. The lower the resolution setting the more recording time is available.  
However, videos recorded at lower resolution are of less quality than videos recorded at the  
higher resolution.  
Remember, the amount of time that you can capture videos also depends on the size of the SD  
memory card inserted as well as the video resolution selected.  
13  
 
Video Capture Mode Quick Function Buttons  
Your digital video recorder has a four-directional pad and additional buttons that functions as  
Quick Function buttons.  
Button  
LEFT  
UP  
Function  
Video Resolution Changes between VGA and QVGA Video Resolution  
Zooms in  
Video Resolution Changes between VGA and QVGA Video Resolution  
RIGHT  
DOWN  
Zooms out  
Other  
Starts and stops your video capture  
Shutter/OK  
Opens and exits the Video Menu options  
Note: To navigate through the Menus, use the Left, Up, Right, and Down  
directions control buttons.  
SET  
Toggles between the Video Capture Mode, Photo Capture Mode, and  
Playback Mode  
MODE  
Video Capture Mode Menus  
The following are the menus that appear in your camcorder‟s Video Capture Mode:  
14  
Image Resolution Menu  
The Image Resolution menu allows you to choose the desired size of the images taken by your  
camcorder. Keep in mind that images with a larger size will also take up more of your  
camcorder‟s memory.  
1) Press the SET button to open the menus for the current mode.  
2) Press the LEFT or RIGHT direction control buttons to scroll and select the Image Resolution  
menu.  
3) Press the UP or DOWN direction control buttons to scroll through the menu options.  
4) Press the Shutter/OK button to select the desired option.  
5)  
A
selected option icon will appear on the selected item.  
6) Press the LEFT or RIGHT button to select the next menu item.  
7) Press the SET button to exit the menu and return to your previous mode.  
8) An icon reflecting your selection will display on the LCD screen.  
9) Remember that this setting will be saved by your camcorder until you manually change the  
setting.  
Language Menu  
You can select your camcorders language setting by selecting the desired language from the  
Language menu.  
1) Press the SET button to open the menus for the current mode.  
2) Press the LEFT or RIGHT direction control buttons to scroll and select the Language menu.  
3) Press the UP or DOWN direction control buttons to scroll through the menu options.  
4) Press the Shutter/OK button to select the desired option.  
5)  
A
selected option icon will appear on the selected item.  
6) Press the LEFT or RIGHT button to select the next menu item.  
7) Press the SET button to exit the menu and return to your previous mode.  
8) Remember that this setting will be saved by your camcorder until you manually change the  
setting.  
15  
Video Playback Mode  
The Playback mode allows you to review photos and videos that you‟ve already taken with your  
digital video recorder.  
When you first turn on the camcorder, the camcorder will be in Video Capture mode by  
default.  
Press the MODE button twice to open the Playback Mode.  
The Playback screen appears with the Playback  
icon appearing on the top left corner of  
the screen.  
Playing Videos on Your Digital Video Recorder  
1) Select your Video:  
Once in Playback mode, press the LEFT or RIGHT direction buttons to scroll through the  
images on your digital video recorder‟s memory card until you find the video you would  
like to view.  
Each captured image (both videos and photos) is displayed on the LCD screen.  
Videos appear with an „AVIicon on the top left of the LCD screen.  
2) Play your selected Video:  
Press the Shutter button to START playing the video.  
- While the Video is playing all the icons on the top section of the LCD disappear.  
- The video playing time is shown on the bottom right.  
Press the Shutter button again to STOP the video.  
16  
 
Video Playback Mode Quick Function Buttons  
Your digital video recorder has a four-directional pad and additional buttons that functions as Quick  
Function buttons.  
Button  
Function  
- Displays the PREVIOUS image  
LEFT  
UP  
- Scrolls through your Thumbnail images  
- Scrolls through your Thumbnail images  
- Displays the NEXT image  
RIGHT  
- Scrolls through your Thumbnail images  
- Opens the Thumbnail display  
DOWN  
Other  
- Scrolls through your Thumbnail images  
- Plays the selected video file  
Shutter/OK  
- Stops the selected playing video  
- Opens selected image from the Thumbnail display  
Opens and exits the Video Playback Delete Menu options  
Note: To navigate through the Menus, use the Left, Up, Right, and Down  
directions control buttons.  
SET /  
DELETE  
Toggles between the Video Capture Mode, Photo Capture Mode, and  
Playback Mode  
MODE  
Thumbnail View  
Easily navigate and select the image you wish to view by using the Thumbnail View.  
The images on your camcorder will be displayed in a 3 X 3 matrix where you can use the  
direction buttons to scroll and select images from the thumbnails.  
1) Press the DOWN button for the images to appear in Thumbnail View.  
2) Use the UP/DOWN/LEFT/RIGHT direction control buttons to navigate the thumbnails and  
select the image you wish to view.  
Videos appear with a „V‟ icon.  
3) Press the Shutter/OK button for the selected image to appear in full screen.  
Note: You can identify from the thumbnail the image type:  
AVI files have a V appear on the thumbnail image  
JPEG files do not have any icons on the thumbnail image  
17  
Video Playback Mode Menu  
The following is the menu that appears in your digital video recorder‟s Video Playback Mode:  
Delete Menu  
While in the Playback mode, you can delete videos from your camcorder through the Delete  
menu.  
Delete This Video:  
1) Select the image you wish to delete.  
1) Press the SET button to open the „Delete‟ menu.  
2) Press the UP or DOWN direction control buttons to highlight the „Delete this Video‟ option,  
and then press the Shutter/OK button confirm and continue.  
3) A „Delete This Video‟ confirmation menu appears.  
- Select „No‟ then press the Shutter/OK button to exit without deleting the selected video.  
- Select „Yes‟ then press the Shutter/OK button to delete the selected video.  
Delete All Images (all videos and photos):  
1) Press the SET button to open the „Delete‟ menu.  
2) Press the UP or DOWN direction control buttons to highlight the „Delete All Images‟ option,  
and then press the Shutter/OK button confirm and continue.  
3) A „Delete All Files?‟ confirmation menu appears.  
- Select „No‟ then press the Shutter/OK button to exit without deleting all of your images.  
- Select „Yes‟ then press the Shutter/OK button to delete all of your captured images.  
Caution: Please use this Delete feature with care. Once all the images are deleted they are  
permanently removed from your SD memory card. Please make sure that you only use this  
feature once you have downloaded and saved all the images you wish to your computer.  
18  
Photo Capture Mode  
The Photo Capture mode allows you to capture pictures with your digital video recorder.  
When the camcorder is first powered ON, the camcorder will be in Video Capture Mode by  
default.  
Press the MODE button once to enter the Photo Capture mode.  
Taking a Picture  
1) Turn on your digital video recorder.  
2) Press the MODE button once to open the Photo Capture Mode.  
3) The  
camera icon will appear on the top left corner of the LCD.  
4) While in Photo Capture mode, use the LCD display to direct the camcorder at the scene you  
would like to capture.  
5) Press the UP - Zoom In and Down - Zoom Out buttons to better set the camcorder display  
if desired.  
6) Press the Shutter button to capture and save your photo to the memory card.  
Note: The lower the resolution setting the more photos can be taken. However lower resolution  
photos are of less quality than photos taken at higher resolution.  
Photo Capture Mode Quick Function Buttons  
Your digital video recorder has a four-directional pad and additional buttons that functions as  
Quick Function buttons.  
Button  
LEFT  
UP  
Function  
Photo Resolution Changes between 1M and VGA Photo Resolution  
Zooms in  
Photo Resolution Changes between 1M and VGA Photo Resolution  
RIGHT  
DOWN  
Zooms out  
Other  
Captures your Photo  
Shutter/OK  
Opens and exits the Photo Menu options  
SET  
19  
 
Note: To navigate through the Menus, use the Left, Up, Right, and Down  
directions control buttons.  
Toggles between the Video Capture Mode, Photo Capture Mode, and  
Playback Mode  
MODE  
Photo Capture Mode Menus  
The following are the menus that appear in your digital video recorder‟s Photo Capture Mode:  
Image Resolution Menu  
The Image Resolution menu allows you to choose the desired size of the images taken by your  
camcorder. Keep in mind that images with a higher resolution will also take up more of your  
camcorder‟s memory.  
1) Press the SET button to open the menus for the current mode.  
2) Press the LEFT or RIGHT direction control buttons to scroll and select the Image Resolution menu.  
3) Press the UP or DOWN direction control buttons to scroll through the menu options.  
4) Press the Shutter/OK button to select the desired option.  
5)  
A
selected option icon will appear on the selected item.  
6) Press the LEFT or RIGHT button to select the next menu item.  
7) Press the SET button to exit the menu and return to your previous mode.  
8) An icon reflecting your selection will display on the LCD screen.  
9) Remember that this setting will be saved by your digital video recorder until you manually  
change the setting or restore the camcorder‟s default factory settings.  
20  
Language Menu  
You can select your camcorder‟s language setting by selecting the desired language from the  
Language menu.  
1) Press the SET button to open the menus for the current mode.  
2) Press the LEFT or RIGHT direction control buttons to scroll and select the Language menu.  
3) Press the UP or DOWN direction control buttons to scroll through the menu options.  
4) Press the Shutter/OK button to select the desired option.  
5)  
A
selected option icon will appear on the selected item.  
6) Press the LEFT or RIGHT button to select the next menu item.  
7) Press the SET button to exit the menu and return to your previous mode.  
Photo Playback Mode  
The Playback mode allows you to review photos and videos that you‟ve already taken with your  
digital video recorder.  
When you first turn on the camcorder, the camcorder will be in Video Capture mode by  
default.  
Press the MODE button twice to open the Playback Mode.  
The Playback screen appears with the Playback  
icon appearing on the top left corner of  
the screen.  
Viewing Captured Photos on Your Camcorder  
1) Select your Photo:  
Once in Playback mode, press the LEFT or RIGHT direction control buttons to scroll  
through the images on your digital video recorder‟s memory card until you find the image  
you would like to view.  
Each captured image (both videos and photos) is displayed on the LCD screen.  
Photos appear with a „JPGicon on the top left of the LCD screen.  
21  
 
2) Zooming In/Out of your selected Photo:  
Press the UP / Zoom In button to Zoom In and magnify the selected photo.  
Press the Shutter/OK button then press the LEFT/RIGHT/UP/DOWN buttons to  
navigate around the zoomed photos.  
Press the DOWN/Zoom Out button to Zoom Out of the selected photo or press the  
Shutter/OK button to return back to the photo in full screen.  
Photo Playback Mode Quick Function Buttons  
Your digital video recorder has a four-directional pad and additional buttons that functions as Quick  
Function buttons.  
Button  
Function  
- Displays the PREVIOUS image  
- Scrolls through your Thumbnail images  
- Scrolls through your Thumbnail images  
- Displays the NEXT image  
LEFT  
UP  
RIGHT  
- Scrolls through your Thumbnail images  
- Opens the Thumbnail display  
DOWN  
- Scrolls through your Thumbnail display images  
Other  
Shutter/OK  
- Opens selected image from the Thumbnail display  
Opens and exits the Photo Playback Delete Menu options  
Note: To navigate through the Menus, use the Left, Up, Right, and Down  
directions control buttons.  
SET /  
DELETE  
Toggles between the Video Capture Mode, Photo Capture Mode, and  
Playback Mode  
MODE  
22  
Thumbnail View  
Easily navigate and select the image you wish to view by using the Thumbnail View.  
The images on your camcorder will be displayed in a 3 X 3 matrix where you can use the  
direction buttons to scroll and select images from the thumbnails.  
1) Press the DOWN button for the images to appear in Thumbnail View.  
2) Use the UP/DOWN/LEFT/RIGHT direction control buttons to navigate the thumbnails and  
select the image you wish to view.  
Note: You can identify from the thumbnail the image type:  
AVI files have a V appear on the thumbnail image  
JPEG files do not have any icons on the thumbnail image  
3) Press the Shutter/OK button for the selected image to appear in full screen.  
4) Zooming Into the Image:  
Once in full screen display mode, you can press the UP or DOWN buttons to Zoom In  
and Zoom Out of the photo.  
Once Zoomed In, press the Shutter/OK button to allow navigation of the zoomed in  
photo.  
Photo Playback Mode Menu  
The following is the menu that appears in your digital video recorder‟s Photo Playback Mode:  
Delete Menu  
While in the Playback mode, you can delete photos from your camcorder through the Delete  
menu.  
Remember, you can also quickly access the Delete menu by pressing the Delete button.  
Delete This Photo:  
1) Select the image you wish to delete.  
23  
2) Press the SET button to open the „Delete‟ menu.  
3) Press the UP or DOWN direction control buttons to highlight the „Delete this Photo‟ option,  
and then press the Shutter/OK button confirm and continue.  
4) A „Delete This Photo‟ confirmation menu appears.  
- Select „No‟ then press the Shutter/OK button to exit without deleting the selected photo.  
- Select „Yes‟ then press the Shutter/OK button to delete the selected photo.  
Delete All Images (all videos and photos):  
1) Press the SET button to open the „Delete‟ menu.  
2) Press the UP or DOWN direction control buttons to highlight the „Delete All Images‟ option  
and then press the Shutter/OK button confirm and continue.  
3) A „Delete All Files?‟ confirmation menu appears.  
- Select „No‟ then press the Shutter/OK button to exit without deleting all of your images.  
- Select „Yes‟ then press the Shutter/OK button to delete all of your captured images.  
Caution: Please use this Delete feature with care. Once all the images are deleted they are  
permanently removed from your SD memory card. Please make sure that you only use this  
feature once you have downloaded and saved all the images you wish to your computer.  
24  
Installing the Software  
You must be connected to the internet to install and run the Vivitar Experience Image  
Manager software.  
1) Insert the installation CD into your CD-ROM drive. The installation screen should  
automatically open.  
2) On PC: The Vivitar Experience Image Manager Installer window appears. If the window  
does not appear, open the application‟s CD/DVD drive and click on “Setup.exe” to launch  
the installer.  
3) On Macintosh: Click the icon that appears on the desktop to install the Vivitar Experience  
Image Manager.  
4) If you do not have internet access at the time of inserting the CD-ROM, connect to the  
internet and then click the “Install Vivitar Experience Image Manager” button to begin the  
installation.  
Note: If you do not have internet access, you can still download media from the camcorder. Click  
the “How to transfer photos and videos from my camcorder to my computer” button for  
instructions.  
25  
 
5) If you have internet access, the “Choose your language” window opens, choose your  
language and click “Next” to open the next window.  
6) Select your camera model from the list and click “Next” to open the next window.  
7) Click “Next” to confirm your camera model selection and to install the application.  
8) Please wait while the application is being installed on your computer.  
9) Please review the license terms.  
On PC and Macintosh: Click the “I accept the terms of this license agreement” and then click  
“Next” to continue.  
10) On PC only: Let the “Vivitar Experience Image Manager” installer create the folder to where  
the program will be installed, and then click “Install”.  
11) Please wait while the application continues the installation process on your computer.  
12) On PC: Click the “Close” button when the installation is complete.  
Click the “Launch Vivitar Experience Image Manager” to open the application.  
13) On Macintosh: Click the “Quit” button when the installation is complete.  
Click the “Launch Vivitar Experience Image Manager” to open the application.  
14) If you close the application you can run the Vivitar Experience Image Manager from the  
Programs (PC) or Applications (Mac) menu on your computer.  
Connecting the Camcorder to the Computer  
1) Slide down the USB lever on the side of the digital video recorder to reveal the retractable  
built -in USB connector.  
2) Insert the USB connector into an available USB port on your computer.  
3) Power the camcorder ON.  
4) The first time you connect the device to the computer you will have to wait a few seconds  
until the computer recognizes the device.  
5) As your camcorder is a mass storage device “MSDC” will appear on the LCD, indicating that  
your camcorder is in Mass Storage Mode.  
26  
 
Getting Photos and Videos from your Camcorder to Your Computer  
NOTE: An SD card needs to be inserted. Do not disconnect the USB connector during transfer.  
Doing so will cancel the transfer of any files on their way to your computer.  
1) Select the “Get Images” button from the Main menu.  
2) The “Get Images from device” window opens.  
3) You can select to download photos, videos or both.  
4) Select your camera (removable disk) from the device window. If your camera is the only  
USB device connected then it will be selected automatically.  
5) Select a location on the computer where to place the new photo and video files.  
6) Add the new photo and video files to albums if desired.  
7) Select to remove the media files from the selected device (removable disk) after the import.  
8) Click the “Get Media” button to transfer the photos and videos from your camera to your  
computer.  
27  
 
9) A media download progress bar appears on the bottom left showing the number of media  
files downloading to your computer. A message appears when the download is complete.  
10) The photo and video files that you selected are now downloaded to your computer to the  
selected folder and albums ready for your use.  
Get started!  
Using the Vivitar Experience Image Manager, you can:  
Upload and manage photos and videos to and from the most popular photo sharing and social  
networking sites - Facebook, Flickr, Picasa, MySpace, Photobucket, Twitpic, Twitgoo and  
YouTube  
Seamlessly transfer photos and videos from one social network to another  
Organize your images by creating offline and online albums  
Edit images using automatic and manual tools  
Use automatic “Geotagging” with built in Google Maps  
For more details on how to use the Vivitar Experience Image Manager open the Help file or  
click the “Take a Tour” button on the application’s Home page.  
28  
 
Transferring Images from my Camcorder to my Computer Manually  
WINDOWS  
1) Slide down the lever on the side of the camcorder to reveal the built-in USB connector.  
Use the USB built-in connector on your camcorder to connect your camcorder to the USB  
port on your computer.  
2) “MSDC” appears on the LCD – indicating that your camcorder is in Mass Storage Mode.  
3) A window appears with a list of options, select Open folder to view filesand click OK.  
4) Open the DCIM folder and the folder inside to view the media files.  
5) Select the media and copy the files from this folder into your computer. Optionally, select the  
files and choose Copy from the Edit menu. Then select a folder and choose Paste from the  
Edit menu.  
6) We recommend that you copy the images into the Pictures/My Pictures folder and the  
videos into the Videos/My Videos folder.  
7) Do not disconnect the camcorder from the computer during transfer. Doing so will cancel the  
transfer of any files on their way to your computer.  
MACINTOSH  
1)  
Slide down the lever on the side of the camcorder to reveal the built-in USB connector.  
Use the USB built-in connector on your camcorder to connect your camcorder to the USB  
port on your computer.  
2) “MSDC” appears on the LCD – indicating that your camcorder is in Mass Storage Mode.  
3) The camcorder‟s device icon appears on the desktop.  
4) Click on the device icon and open the DCIM folder and the folder inside to view the media  
files.  
5) Select the files and drag them into your computer. Optionally, select the files and choose  
Copy from the Finder‟s Edit menu. Then select a folder and choose Paste from the Edit  
menu.  
6) We recommend that you copy the images into the Pictures folder and the videos into the  
Movies folder.  
7) Do not disconnect the camcorder from the computer during transfer. Doing so will cancel the  
transfer of any files on their way to your computer.  
29  
 
Camcorder Maintenance  
The digital video recorder is a delicate device.  
Always wear the wrist strap to prevent the device from falling.  
Please handle your camcorder with care to avoid damaging it.  
Do not expose your digital video recorder to heat sources.  
Do not use you digital video recorder in wet or moist conditions.  
To clean the lens, first blow away the dust on the surface of the lens, then use a proper cloth or  
tissue for optical devices to clean the lens. If necessary, use lens cleanser.  
Never use organic cleanser to clean the digital video camera.  
Never touch the lens with your fingers.  
When left idle for an extended period of time, store the digital video recorder without the batteries,  
in a dry and dark place.  
Sakar Warranty Card  
This warranty covers for the original consumer purchaser only and is not transferable. Products  
that fail to function properly UNDER NORMAL USAGE, due to defects in material or  
workmanship will be repaired at no charge for parts or labor for a period of one year from the time  
of purchase.  
What Is Not Covered By Warranty:  
Damages or malfunctions not resulting from defects in material or workmanship and damages or  
malfunctions from other than normal use, including but limited to, repair by unauthorized parties,  
tampering, modification or accident.  
What To Do When Service Is Required:  
When returning your defective product (postage pre-paid) for service, your package should  
include:  
30  
   
1) Copy of original bill of sale  
2) A detailed written description of the problem.  
3) Your return address and telephone number (Daytime)  
MAIL TO ADDRESS BELOW:  
Sakar US  
Sakar UK/Europe  
Sakar Australia  
Sakar International  
Attention: Service Department  
195 Carter Drive  
Edison, NJ  
Attention: Service Department  
2D, Siskin Parkway East  
4020 Middlemarch Business Park  
Coventry, CV3 4PE  
Return faulty camera to the  
Refund Counter at the store  
where purchased  
08817  
Technical Support  
For technical support issues please visit our website at www.vivitar.com. You can find manuals,  
software and FAQ‟s at the website. Can‟t find what you are looking for? E-mail us at  
[email protected] and one of our technical support team members will answer your  
questions. For phone support in the US please call 1-800-592-9541, in the UK call 0800 917 4831,  
in Australia call 1800-006-614. If you would like to call from anywhere else, please visit  
www.vivitar.com for your local toll free number.  
31  
 
Troubleshooting  
Q: I have taken photos and selected the “Get Images” button. I get a message that the  
images were successfully transferred but the photos do not appear on my computer.  
What do I do?  
Ensure that you have in fact taken photos. Press the Shutter button to take some sample photos  
and then try downloading them again.  
With test photos, if the camera powers off before you upload them to the computer the photos are  
not stored in the cameras memory. These photos should be uploaded quickly before the camera  
powers off. If the photos are saved to the SD memory card then all the photos should appear.  
Q: How do I make sure I don't lose important pictures?  
This camera requires an SD card for normal use. If the camera powers off nothing will happen to  
the images stored on the SD memory card. We recommend always downloading your photos to  
your computer as soon as possible to prevent unintentional data loss.  
Q: I deleted images using the Vivitar Experience Image Manager. The images were also  
deleted from my computer. How do I recover images that I accidently deleted?  
All images deleted using the Vivitar Experience Image Manager are sent to your computer`s  
Recycle or Trash Bin and can be retrieved from there.  
DVR380HD063011ver1TA FW21101SADKHE010  
32  
 

Windmere WMBLH3V User Manual
Tokina VARIFOCAL LENS TVR0614 User Manual
Soundstream Technologies EXC 8 User Manual
Sony Handycam 4 170 539 1100000000#User Manual
Sony Ericsson PDW 530P User Manual
Slick VC125 User Manual
Sharp Calculator EL 1750PIII User Manual
Seanix Epson ActionNote 900 User Manual
Samsung DualView ST700 User Manual
Samsung Blu ray Player BD f5500e User Manual