3-866-124-12 (1)
Dig it a l
Vid e o Ca m e ra
Re co rd e r
Operating Instructions
Before operating the unit, please read this manual thoroughly,
and retain it for future reference.
Owner’s Record
The model and serial numbers are located on the bottom. Record the
serial number in the space provided below. Refer to these numbers
whenever you call upon your Sony dealer regarding this product.
Model No. DCR-TRV
Model No. AC-
Serial No.
Serial No.
DCR-TRV510
©1999 by Sony Corporation
Ta b le o f co n t e n t s
Qu ick St a rt Gu id e ............................... 4
Fla sh Me m o ry Op e ra t io n s
Using the flash memory function
– introduction ...................................... 54
Ge t t in g st a rt e d
Recording still images in the built-in flash
memory
Using this manual ....................................... 6
Checking supplied accessories .................. 7
Step 1 Preparing the power supply ......... 8
Installing the battery pack .............. 8
Charging the battery pack .............. 9
Connecting to a wall outlet ........... 11
Step 2 Inserting a cassette ........................ 12
– Memory photo recording ............... 58
Recording an image from a recorded tape
as a still image ..................................... 61
Copying still images from a recorded tape
– PHOTO SAVE .................................. 63
Viewing a still picture
– Memory photo playback ................ 65
Playing back images in a continuous loop
– SLIDE SHOW .................................. 69
Re co rd in g – Ba sics
Recording a picture ................................... 13
Preventing accidental erasure
Shooting backlit subjects
– PROTECT ......................................... 70
(BACK LIGHT) ........................ 19
Deleting images – DELETE ...................... 71
Copying images recorded in the built-in
flash memory to tapes ........................ 74
Shooting in the dark
(NightShot) ............................... 19
Checking the recording
– END SEARCH / EDITSEARCH /
Rec Review .......................................... 21
Cu st o m izin g Yo u r Ca m co rd e r
Changing the MENU settings .................. 76
Resetting the date and time ..................... 82
Pla yb a ck – Ba sics
Playing back a tape .................................... 22
Viewing the recording on TV .................. 25
Ad d it io n a l In fo rm a t io n
Digital8 system, recording and playback
............................................................... 83
Changing the lithium battery in your
camcorder ............................................ 85
Troubleshooting ......................................... 87
Self-diagnosis display ............................... 91
Warning indicators and messages .......... 92
Using your camcorder abroad ................. 93
Maintenance information and precautions
............................................................... 94
Ad va n ce d Re co rd in g Op e ra t io n s
Photo recording ......................................... 27
Using the wide mode ................................ 29
Using the fader function ........................... 30
Using special effects
– Picture effect ..................................... 33
Using special effects
– Digital effect ..................................... 34
Using the PROGRAM AE function ......... 37
Adjusting the exposure manually ........... 39
Focusing manually .................................... 40
Inserting a scene ........................................ 41
Specifications .............................................. 98
Qu ick Re fe re n ce
Identifying the parts and controls ........... 99
Quick Function Guide ............................ 106
Index .......................................................... 107
Ad va n ce d Pla yb a ck Op e ra t io n s
Playing back a tape with picture effects
............................................................... 42
Playing back a tape with digital effects
............................................................... 43
Quickly locating a scene using the zero set
memory function ................................ 44
Searching a recording by date ................. 45
•
•
•
IBM PC/ AT is a registered trademark of
International Business Machines Corporation of
the U.S.A.
MS-DOS and Windows are registered trademarks
licensed to Microsoft Corporation, registered in the
U.S.A. and other countries.
All other product names mentioned herein may be
the trademarks or registered trademarks of their
respective companies.
Searching for a photo
– Photo search/ Photo scan ............... 47
Ed it in g o n Ot h e r Eq u ip m e n t
Dubbing a tape ........................................... 49
Recording video or TV programs ........... 51
Inserting a scene from a VCR .................. 52
Furthermore, “ ” and “ ” are not mentioned in each
case in this manual.
3
Qu ick St a rt Gu id e
This chapter introduces you to the basic features of your
camcorder. See the page in parentheses “( )” for more
information.
Co n n e ct in g t h e p o w e r co rd (p . 11)
Use the battery pack when using your camcorder outdoors (p. 8).
Open the DC IN
jack cover.
Connect the plug with
its 4 mark facing up.
AC power adaptor (supplied)
In se rt in g a ca sse t t e (p . 12)
1Slide EJECT in the
direction of the arrow
while pressing the
small blue button.
2Insert a cassette
into the cassette
compartment
with its
3Close the cassette
compartment by
pressing the “PUSH”
mark on the cassette
compartment. The
cassette compartment
automatically goes
down.
window facing
out.
4
Re co rd in g a p ict u re (p . 13)
1Remove the lens cap.
4Turn STANDBY to STANDBY. The
picture appears on the LCD screen.
K
2Set the POWER switch to CAMERA
while pressing
the small green
button.
POWER
CAMERA
OFF
START/STOP
VTR
5Press the red button. Your camcorder
starts recording. To stop recording,
press the red button again.
K
START/STOP
3Open the LCD panel
while pressing
OPEN.
View finder
When the LCD panel is closed, use the
viewfinder placing your eye against its eyecup.
Mo n it o rin g t h e p la yb a ck p ict u re o n t h e LCD
scre e n (p . 22)
1Set the POWER switch to VTR
2Press 0 to rewind the tape.
while pressing the small green
REW
button.
POWER
CAMERA
OFF
VTR
3Press ( to start playback.
PLAY
NOTE
Do not pick up your camcorder by holding
the viewfinder or by holding the LCD
panel.
5
— Ge t t in g st a rt e d —
Usin g t h is m a n u a l
As you read through this manual, buttons and settings on your camcorder are shown in
capital letters.
e.g. Set the POWER switch to CAMERA.
When you carry out an operation, you can hear a beep sound to indicate that the
operation is being carried out.
Be fo re u sin g yo u r ca m co rd e r
With your digital camcorder, you can use Hi8 video cassettes H.
Your camcorder records and plays back pictures in the Digital8 system. Also your
camcorder plays back tapes recorded in the Hi8 H/ standard 8 h (analog) system.
You, however, cannot use the functions in “Advanced Playback Operations” on page 42
to 48 for playback in the Hi8 H/ standard 8 h system. To enable smooth transition,
we recommend that you do not mix pictures recorded in the Hi8 H/ standard 8 h
with the Digital8 system on a tape.
No t e o n TV co lo r syst e m s
TV color systems differ from country to country. To view your recordings on a TV, you
need an NTSC system-based TV.
Co p yrig h t p re ca u t io n s
Television programs, films, video tapes, and other materials may be copyrighted.
Unauthorized recording of such materials may be contrary to the provision of the
copyright laws.
Pre ca u t io n s o n ca m co rd e r ca re
• The LCD screen and/or the color view finder are manufactured using high-
precision technology. How ever, there may be some tiny black spots and/or
bright spots (red, blue or green in color) that constantly appear on the LCD
screen and/or in the color view finder. These spots occur normally in the
manufacturing process and do not affect the recorded picture in any w ay.
Effective number of pixels is 99.99% or more.
• Do not let your camcorder get wet. Keep your camcorder away from rain and sea
water. Letting your camcorder get wet may cause your camcorder to malfunction.
Sometimes this malfunction cannot be repaired [a ].
• Never leave your camcorder exposed to temperatures above 140°F (60°C ), such as in a
car parked in the sun or under direct sunlight [b ].
• Do not place your camcorder so as to point the viewfinder or the LCD screen toward
the sun. The inside of the viewfinder or LCD screen may be damaged [c].
[a ]
[b ]
[c]
6
Ch e ckin g su p p lie d a cce sso rie s
Make sure that the following accessories are supplied with your camcorder.
1
4
8
2
5
9
3
7
!¡
6
!º
1 Wireless Remote Commander (1)
6 A/V connecting cable (1) (p. 25)
7 Shoulder strap (1) (p. 102)
8 Lens cap (1) (p. 13)
(p. 104)
2 AC-L10A/L10B/L10C AC pow er adaptor
(1), Pow er cord (1) (p. 9)
3 NP-F330 battery pack (1) (p. 8, 9)
9 PC serial cable (1) (p. 68)
4 CR2025 lithium battery (1) (p. 85)
The lithium battery is already installed
in your camcorder.
!º Application softw are: PictureGear
3.2Lite (1) (p. 68)
!¡ Label sheet for cassette (1)
5 Size AA (R6) battery for Remote
Stick this label on the recorded cassette.
Commander (2) (p. 104)
Contents of the recording cannot be compensated if recording or playback is not
made due to a malfunction of the camcorder, video tape, etc.
7
St e p 1 Pre p a rin g t h e p o w e r su p p ly
In st a llin g t h e b a t t e ry p a ck
Install the battery pack to use your camcorder outdoors.
Slide the battery pack down.
To re m o ve t h e b a t t e ry p a ck
Slide the battery pack out in the direction of the arrow while pressing BATT
RELEASE down.
BATT RELEASE
After installing the battery pack
Do not carry your camcorder by holding the battery pack. If you do so, the battery pack
may slide off your camcorder unintentionally, damaging your camcorder.
8
St e p 1 Pre p a rin g t h e p o w e r su p p ly
Ch a rg in g t h e b a t t e ry p a ck
Use the battery pack after charging it for your camcorder.
Your camcorder operates only with the “InfoLITHIUM” battery pack (L series).
“InfoLITHIUM” is a trademark of Sony Corporation.
(1) Open the DC IN jack cover and connect the AC power adaptor supplied with
your camcorder to the DC IN jack with the plug’s 4 mark facing up.
(2) Connect the power cord to the AC power adaptor.
(3) Connect the power cord to a wall outlet.
(4) Set the POWER switch to OFF. Charging begins. The remaining battery time is
indicated in minutes on the display window.
When the remaining battery indicator changes to ı, normal charge is completed. To
fully charge the battery (full charge), leave the battery pack attached for about 1 hour
after normal charge is completed until FULL appears in the display window. Fully
charging the battery allows you to use the battery longer than usual.
POWER
4
CAMERA
OFF
VTR
1
2
Note
Prevent metallic objects from coming into contact with the metal parts of the DC plug of
the AC power adaptor. This may cause a short-circuit, damaging the AC power
adaptor.
Remaining battery time indicator
The remaining battery time indicator in the display window roughly indicates the
recording time with the viewfinder.
Battery pack
The battery pack is charged a little before it leaves the factory.
Until your camcorder calculates the actual remaining battery time
“– – – – min” appears in the display window.
9
St e p 1 Pre p a rin g t h e p o w e r su p p ly
Ch a rg in g t im e
Battery pack
Full charge (Normal charge)
NP-F330 (supplied)
NP-F530/ F550
150 (90)
210 (150)
300 (240)
390 (330)
NP-F730/ F730H/ F750
NP-F930/ F950
Approximate number of minutes to charge an empty battery pack
Re co rd in g t im e
Recording w ith
the view finder
Recording w ith
the LCD screen
Battery
pack
Continuous*
Typical**
50 (45)
Continuous*
Typical**
35 (30)
NP-F330 (supplied)
NP-F530
95 (85)
65 (60)
160 (145)
195 (175)
325 (290)
395 (355)
515 (465)
610 (550)
90 (80)
105 (95)
60 (55)
NP-F550
110 (100)
185 (165)
225 (200)
295 (265)
350 (315)
135 (120)
245 (220)
280 (250)
385 (345)
435 (390)
75 (65)
NP-F730
140 (125)
160 (140)
220 (195)
250 (225)
NP-F730H/ F750
NP-F930
NP-F950
Approximate number of minutes when you use a fully charged battery
Numbers in parentheses “( )” indicate the time using a normally charged battery.
*
Approximate continuous recording time at 77°F (25°C). The battery life will be
shorter if you use your camcorder in a cold environment.
** Approximate number of minutes when recording while you repeat recording start/
stop, zooming and turning the power on/ off. The actual battery life may be shorter.
Pla yin g t im e
Battery
pack
Playing time
on LCD screen
Playing time
w ith LCD closed
NP-F330 (supplied)
NP-F530
65 (55)
95 (85)
100 (90)
155 (140)
190 (170)
315 (285)
385 (345)
495 (450)
590 (530)
NP-F550
130 (115)
235 (210)
270 (240)
370 (330)
415 (370)
NP-F730
NP-F730H/ F750
NP-F930
NP-F950
Approximate number of minutes when you use a fully charged battery
Numbers in parentheses “( )” indicate the time using a normally charged battery. The
battery life will be shorter if you use your camcorder in a cold environment.
10
St e p 1 Pre p a rin g t h e p o w e r su p p ly
After charging the battery pack
Disconnect the AC power adaptor from the DC IN jack on your camcorder.
Note on the remaining battery time indicator during recording
The indicator may not be correct, depending on the conditions in which you are
recording. When you close the LCD panel and open it again, it takes about 1 minute for
the correct remaining battery time to be displayed.
What is ”InfoLITHIUM”?
The “InfoLITHIUM” is a lithium ion battery pack which can exchange data such as
battery consumption with compatible video equipment. This unit is compatible with the
“InfoLITHIUM” battery pack (L series). Your camcorder operates only with the
“InfoLITHIUM” battery. “InfoLITHIUM” battery packs have the
“InfoLITHIUM” is a trademark of Sony Corporation.
mark.
Co n n e ct in g t o a w a ll o u t le t
When you use your camcorder for a long time, we recommend that you power it from a
wall outlet using the AC power adaptor.
(1) Open the DC IN jack cover, and connect the AC power adaptor to the DC IN
jack on your camcorder with the plug’s 4 mark facing up.
(2) Connect the power cord to the AC power adaptor.
(3) Connect the power cord to a wall outlet.
2, 3
1
WARNING
The power cord must only be changed at a qualified service shop.
PRECAUTION
The set is not disconnected from the AC power source (house current) as long as it is
connected to the wall outlet, even if the set itself has been turned off.
Notes
• The AC power adaptor can supply power even if the battery pack is attached to your
camcorder.
• The DC IN jack has “source priority”. This means that the battery pack cannot supply
any power if the power cord is connected to the DC IN jack, even when the power
cord is not plugged into a wall outlet.
• Keep the AC power adaptor away from the camcorder if the picture is disturbed.
Using a car battery
Use Sony DC Adaptor/ Charger (not supplied).
11
St e p 2 In se rt in g a ca sse t t e
We recommend using Hi8 video cassettes H.
If you use standard 8 h tape, be sure to play back the tape on this camcorder.
Your camcorder records in the Digital8 system.
(1) Slide EJECT in the direction of the arrow while pressing the small blue button.
The cassette compartment automatically lifts up and opens.
(2) Insert a cassette with its window facing out and the tab on the cassette up.
(3) Close the cassette compartment by pressing the “PUSH” mark on the cassette
compartment. The cassette compartment automatically goes down.
1
2
3
To e je ct a ca sse t t e
Slide EJECT in the direction of the arrow while pressing the small blue button.
Notes
• The recording time when you use your Digital8 system camcorder on Hi8/ standard
8 tape is half the recording time when using the conventional Hi8/ standard 8 system
camcorder.
• If you use standard 8 tape, be sure to play back the tape on this camcorder. Mosaic
pattern noise may appear when you play back standard 8 tape on other VCRs.
• Do not press the cassette compartment down. Doing so may cause malfunction.
To prevent accidental erasure
Slide the write-protect tab on the cassette to expose the red mark.
12
— Re co rd in g – Ba sics —
Re co rd in g a p ict u re
Your camcorder automatically focuses for you.
(1) Remove the lens cap by pressing both knobs on its sides and attatch the lens
cap to the grip strap.
(2) Install the power source and insert a cassette. See “Step 1” and “Step 2” for
more information (p. 8 to 12).
(3) Set the POWER switch to CAMERA while pressing the small green button.
(4) Open the LCD panel while pressing OPEN. The viewfinder automatically
turns off.
(5) Turn STANDBY to STANDBY.
(6) Press START/ STOP. Your camcorder starts recording. The “REC” indicator
appears. The camera recording lamp located on the front of your camcorder
lights up. To stop recording, press START/ STOP again.
1
5
6
3
4
POWER
CAMERA
OFF
VTR
2
K
STBY 0:00:00
40min
START/STOP
REC 0:00:01
40min
K
Microphone
Camera recording
lamp
START/STOP
Note
Fasten the grip strap firmly. Do not touch the built-in microphone during recording.
To enable smooth transition
You can make the transition between the last scene you recorded and the next scene
smooth as long as you do not eject the cassette. When you exchange the battery pack in
the recording mode, set STANDBY to LOCK.
If you leave your camcorder in the standby mode for 3 minutes w hile the cassette
is inserted
Your camcorder automatically turns off. This is to save battery power and to prevent
battery and tape wear. To resume the standby mode, turn STANDBY down and up
again. To start recording, press START/ STOP.
13
Re co rd in g a p ict u re
Ad ju st in g t h e LCD scre e n
To adjust the brightness of the LCD screen, press either of the two buttons on LCD
BRIGHT.
The LCD panel moves about 90 degrees to the viewfinder side and about 210 degrees to
the lens side.
If you turn the LCD panel over so that it faces the other way, the
indicator appears
in the viewfinder and on the LCD screen (Mirror mode).
210°
to brighten
90°
to dim
When closing the LCD panel, set it vertically until it clicks, and swing it into the
camcorder body.
Note
When using the LCD screen except in the mirror mode, the viewfinder automatically
turns off.
When you use the LCD screen outdoors in direct sunlight
The LCD screen may be difficult to see. If this happens, we recommend that you use the
viewfinder.
Picture in the mirror mode
The picture on the LCD is a mirror-image. However, the picture will be normal when
recorded.
During recording in the mirror mode
While recording in the mirror mode, you cannot operate the following buttons:
ZERO SET MEMORY on the Remote Commander and MENU on your camcorder.
Indicators in the mirror mode
The STBY indicator appears as Pr and REC as r. Some of the other indicators appear
mirror-reversed and others are not displayed.
14
Re co rd in g a p ict u re
Se lf-t im e r re co rd in g
You can make a recording with the self-timer. This mode is useful when you want to
record yourself.
(1) Press
(self-timer).
(self-timer) indicator appears in the viewfinder or on the LCD screen.
The
(2) Press START/ STOP.
Self-timer starts counting down from 10 with a beep sound. In the last two
seconds of the countdown, the beep sound gets faster, then recording starts
automatically.
START/ STOP
To st o p t h e se lf-t im e r d u rin g re co rd in g
Press START/ STOP.
To re co rd st ill p ict u re s u sin g t h e se lf-t im e r
Press PHOTO in step 2.
To ca n ce l se lf-t im e r re co rd in g
Press
so that the
indicator disappears from the LCD screen or viewfinder while
the camcorder is in the standby mode.
The self-timer recording mode is automatically canceled w hen
• Self-timer recording is finished.
• The POWER switch is set to OFF or VTR.
Aft e r re co rd in g
(1) Turn STANDBY down to LOCK.
(2) Close the LCD panel.
(3) Eject the cassette.
(4) Set the POWER switch to OFF.
15
Re co rd in g a p ict u re
To re co rd p ict u re s w it h t h e vie w fin d e r – a d ju st in g t h e
vie w fin d e r
If you record pictures with the LCD panel closed, check the picture with the viewfinder.
Adjust the viewfinder lens to your eyesight so that the indicators in the viewfinder
come into sharp focus.
Lift up the viewfinder and move the viewfinder lens adjustment lever.
16
Re co rd in g a p ict u re
Usin g t h e zo o m fe a t u re
Move the power zoom lever a little for a slower zoom. Move it further for a faster zoom.
Using the zoom function sparingly results in better-looking recordings.
“T” side: for telephoto (subject appears closer)
“W” side: for wide-angle (subject appears farther away)
W
W
T
T
W
T
Zoom greater than 20× is performed digitally, if you set D ZOOM to ON in the MENU
settings. The digital zoom function is set OFF at the factory. (p. 76)
W
T
The right side of the bar shows
the digital zooming zone.
The digital zooming zone appears
when you set D ZOOM to ON.
When you shoot close to a subject
If you cannot get a sharp focus, move the power zoom lever to the “W” side until the
focus is sharp. You can shoot a subject that is at least about 2 feet 5/ 8 inch (about 80 cm)
away from the lens surface in the telephoto position, or about 1/ 2 inch (about 1 cm)
away in the wide-angle position.
Notes on digital zoom
• Digital zoom starts to function when zoom exceeds 20×.
• The picture quality deteriorates as you go toward the “T” side. Set D ZOOM to OFF in
the MENU settings. Otherwise the digital zoom activates without notice (p. 76).
17
Re co rd in g a p ict u re
START/STOP MODE se t t in g
: Recording starts when you press START/ STOP, and stops when you press it again
(factory setting).
ANTI GROUND SHOOTING
: The camcorder records only while you press START/
STOP. Use this mode to avoid recording unnecessary
scenes.
5SEC: When you press use this mode to START/ STOP, your camcorder records for 5
seconds and then stops automatically.
START/STOP
MODE
5SEC
ANTI
GROUND
SHOOTING
Notes
• You cannot use the fader function in the 5SEC or
• The time code does not appear in the 5SEC mode.
mode.
To extend the recording time in the 5SEC mode
Five dots (rrrrr) appear, and then disappear at a rate of one per second. To extend
the recording time, press START/ STOP again before all the dots disappear. Recording
continues for about 5 seconds from the moment you press START/ STOP.
In d ica t o rs d isp la ye d in t h e re co rd in g m o d e
The indicators are not recorded on tape.
Format indicator
STANDBY/REC indicator
Time code/Tape counter
REC 0:00:01
40min
Remaining tape indicator
This appears after you insert a cassette for a while.
Remaining battery time indicator
Time code (for tapes recorded in the Digital8 system only)
The time code indicates the recording or playback time, “0:00:00”
(hours:minutes:seconds) in CAMERA mode and “0:00:00:00”
(hours:minutes:seconds:frames) in VTR mode. You cannot rewrite only the time code.
Your camcorder uses the drop frame mode.
When you play back tapes recorded in the Hi8/ standard 8 system, the tape counter
appears.
18
Re co rd in g a p ict u re
Sh o o t in g b a cklit su b je ct s (BACK LIGHT)
When you shoot a subject with the light source behind the subject or a subject with a
light background, use the backlight function.
Press BACK LIGHT in the recording or standby mode.
The c indicator appears in the viewfinder or on the LCD screen.
To cancel, press BACK LIGHT again.
BACK LIGHT
If you press EXPOSURE w hen shooting backlit subjects
The backlight function will be canceled.
Sh o o t in g in t h e d a rk (Nig h t Sh o t )
The NightShot function enables you to shoot a subject in a dark place. For example, you
can satisfactorily record the environment of nocturnal animals for observation when
you use this function.
(1) While your camcorder is in the standby mode, slide NIGHTSHOT to ON.
(2) Press START/ STOP to start recording.
and “NIGHTSHOT” indicators flash on the LCD screen or in the
viewfinder. To cancel the NightShot function, slide NIGHTSHOT to OFF.
NIGHTSHOT
+
SLOW
SHUTTER
OFF ON
NightShot Light
emitter
19
Re co rd in g a p ict u re
Usin g +SLOW SHUTTER
The NightShot +Slow shutter mode makes subjects more than four times brighter than
those recorded in the NightShot mode.
(1) Slide NIGHTSHOT to ON in the standby mode.
indicator appears.
(2) Press +SLOW SHUTTER until the desired NIGHTSHOT indicator flashes.
The indicator changes as follows:
(NIGHTSHOT) n
(NIGHTSHOT1) n
(NIGHTSHOT2) n
(NIGHTSHOT)
To cancel the NightShot +Slow shutter mode, slide NIGHTSHOT to OFF.
Usin g t h e Nig h t Sh o t Lig h t
The picture will be clearer with the NightShot Light on. To enable NightShot Light, set
N.S.LIGHT to ON in the MENU settings (p. 76).
Notes
• Do not use the NightShot function in bright places (ex. outdoors in the daytime). This
may cause your camcorder to malfunction.
• When you keep NIGHTSHOT set to ON in normal recording, the picture may be
recorded in incorrect or unnatural colors.
• If focusing is difficult with the autofocus mode when using the NightShot function,
focus manually.
While using the NightShot function, you can not use the follow ing functions:
– Exposure
– PROGRAM AE
– Fader*
– Digital effect*
* You cannot use these functions only in the NightShot +Slow shutter mode.
Shutter speed in the NightShot +Slow shutter mode
Indicator
(NIGHTSHOT1)
(NIGHTSHOT2)
Shutter speed
1/ 15
1/ 4
The +SLOW SHUTTER button does not w ork:
– while the fader function is set or in use
– while the digital effect function is in use
– when NIGHTSHOT is set to OFF
NightShot Light
NightShot Light rays are infrared and so are invisible. The maximum shooting distance
using the NightShot Light is about 10 feet (3 m). The shooting distance will be twice or
more in the NightShot +Slow shutter mode.
20
Ch e ckin g t h e re co rd in g
– END SEARCH / EDITSEARCH / Re c Re vie w
You can use these buttons to check the recorded picture or shoot so that the transition
between the last recorded scene and the next scene you record is smooth.
EDITSEARCH
END SEARCH
END SEARCH
You can go to the end of the recorded section after you record.
Press END SEARCH in the standby mode.
The last 5 seconds of the recorded section are played back and playback stops. You can
monitor the sound from the speaker or headphones.
EDITSEARCH
You can search for the next recording start point.
Hold down the +/ – (Œ) side of EDITSEARCH in the standby mode. The recorded
section is played back.
+ : to go forward
– : to go backward
Release EDITSEARCH to stop playback. If you press START/ STOP, re-recording begins
from the point you released EDITSEARCH. You cannot monitor the sound.
Re c Re vie w
You can check the last recorded section.
Press the – (Œ) side of EDITSEARCH momentarily in the standby mode.
The last few seconds of the recorded section are played back. You can monitor the
sound from the speaker or headphones.
Notes
• END SEARCH, EDITSEARCH and Rec Review work only for tapes recorded in the
Digital8 system.
• If you start recording after using the end search function, occasionally, the transition
between the last scene you recorded and the next scene may not be smooth.
• The end search function may not work when there is a blank portion between pictures
on a tape.
Once you eject the cassette after you have recorded on the tape
The end search function does not work.
21
— Pla yb a ck – Ba sics —
Pla yin g b a ck a t a p e
You can monitor the playback picture on the LCD screen or in the viewfinder. You can
control playback using the Remote Commander supplied with your camcorder.
(1) Install the power source and insert the recorded tape.
(2) Set the POWER switch to VTR while pressing the small green button. The
video control buttons light up.
(3) Open the LCD panel while pressing OPEN.
(4) Press 0 to rewind the tape.
(5) Press ( to start playback.
(6) To adjust the volume, press either of the two buttons on VOLUME. The
speaker on your camcorder is silent when the LCD panel is closed.
2
4
POWER
CAMERA
OFF
REW
VTR
5
6
PLAY
3
To st o p p la yb a ck
Press p.
When monitoring on the LCD screen
You can turn the LCD panel over and move it back to the camcorder body with the
LCD screen facing out [a ]. You can adjust the angle of the LCD panel by lifting the LCD
panel up by 15 degrees [b ].
[a ]
[b ]
15°
22
Pla yin g b a ck a t a p e
To d isp la y t h e scre e n in d ica t o rs – Disp la y fu n ct io n
Press DISPLAY on your camcorder or the Remote Commander supplied with your
camcorder.
The indicators appear on the LCD screen.
To make the indicators disappear, press DISPLAY again.
DATA CODE
DISPLAY
Usin g t h e d a t a co d e fu n ct io n
Your camcorder automatically records not only images on the tape but also the
recording data (date/ time or various settings when recorded) (Data code function).
Press DATA CODE on your camcorder or the Remote Commander in the playback
mode.
The display changes as follows:
date/ time n various settings (SteadyShot, exposure AUTO/ MANUAL, white balance,
gain, shutter speed, aperture value) n no indicator
AUTO
60 AWB
F1.4 9dB
JUL
12:05:56 AM
4
1999
Not to display recording data
Set DATA CODE to DATE in the MENU settings (p. 76)
The display changes as follows:
date/ time n no indicator
Note on the data code function
The data code function works only for tapes recorded in the Digital8 system.
Recording data
Recording data is your camcorder’s information when you have recorded. In the
recording mode, the recording data will not be displayed.
When you use data code function, bars (-- -- --) appear if:
• A blank section of the tape is being played back.
• The tape is unreadable due to tape damage or noise.
• The tape was recorded by a camcorder without the date and time set.
23
Pla yin g b a ck a t a p e
Va rio u s p la yb a ck m o d e s
To operate control buttons, set the POWER switch to VTR.
To vie w a st ill p ict u re (p la yb a ck p a u se )
Press P during playback. To resume playback, press P or (.
To a d va n ce t h e t a p e
Press ) in the stop mode. To resume normal playback, press (.
To re w in d t h e t a p e
Press 0 in the stop mode. To resume normal playback, press (.
To ch a n g e t h e p la yb a ck d ire ct io n
Press < on the Remote Commander during playback to reverse the playback direction.
To resume normal playback, press ( .
To lo ca t e a sce n e m o n it o rin g t h e p ict u re (p ict u re se a rch )
Keep pressing 0 or ) during playback. To resume normal playback, release the
button.
To m o n it o r t h e h ig h -sp e e d p ict u re w h ile a d va n cin g o r
re w in d in g t h e t a p e (skip sca n )
Keep pressing 0 while rewinding or ) while advancing the tape. To resume
rewinding or advancing, release the button.
To vie w t h e p ict u re a t slo w sp e e d (slo w p la yb a ck)
Press . on the Remote Commander during playback. For slow playback in the reverse
direction, press <, then press . on the Remote Commander. To resume normal
playback, press (.
To vie w t h e p ict u re a t d o u b le sp e e d
Press ×2 on the Remote Commander during playback. For double speed playback in the
reverse direction, press <, then press x2 on the Remote Commander. To resume
normal playback, press (.
To vie w t h e p ict u re fra m e -b y-fra m e
Press 7 on the Remote Commander in the playback pause mode. For frame-by-frame
playback in the reverse direction, press '. To resume normal playback, press (.
To se a rch t h e la st sce n e re co rd e d (END SEARCH)
Press END SEARCH in the stop mode. The last 5 seconds of the recorded section plays
back and stops.
In the various playback modes
• Noise may appear when your camcorder plays back tapes recorded in the Hi8/
standard 8 system.
• Sound is muted.
• The previous recording may appear as a mosaic image when playing back in the
Digital8 system.
When the playback pause mode lasts for 3 minutes
• Your camcorder automatically enters the stop mode. To resume playback, press (.
• The previous recording may appear.
Slow playback for tapes recorded in the Digital8 system
The slow playback can be performed smoothly; however, this function does not work
for an output signal from the DV IN/ OUT jack.
24
Vie w in g t h e re co rd in g o n TV
Connect your camcorder to your TV or VCR with the A/ V connecting cable supplied
with your camcorder to watch the playback picture on the TV screen. You can operate
the playback control buttons in the same way as when you monitor playback pictures
on the LCD screen. When monitoring the playback picture on the TV screen, we
recommend that you power your camcorder from a wall outlet using the AC power
adaptor (p. 11). Refer to the operating instructions of your TV or VCR.
Open the jack cover. Connect your camcorder to the TV using the A/ V connecting
cable. Then, set the TV/ VCR selector on the TV to VCR.
IN
S VIDEO
S VIDEO
VIDEO
VIDEO
AUDIO
AUDIO
: Signal flow
If yo u r TV is a lre a d y co n n e ct e d t o a VCR
Connect your camcorder to the LINE IN input on the VCR by using the A/ V connecting
cable supplied with your camcorder. Set the input selector on the VCR to LINE.
If yo u r TV o r VCR is a m o n a u ra l t yp e
Connect the yellow plug for video and the white plug for audio on both your
camcorder and the TV or the VCR (you do not connect the red plug).
With this connection, the sound is monaural even on stereo models.
To co n n e ct t o a TV o r VCR w it h o u t Vid e o /Au d io in p u t ja cks
Use an NTSC system RFU adaptor (not supplied).
Refer to the operating instructions of your TV or VCR and the RFU adaptor. With an
RFU adaptor, the sound is monaural.
If your TV or VCR has an S video jack
Connect using an S video cable (not supplied) to obtain high-quality pictures. With this
connection, you do not need to connect the yellow (video) plug of the A/ V connecting
cable.
Connect the S video cable (not supplied) to the S video jacks on both your camcorder
and the TV or the VCR.
25
Vie w in g t h e re co rd in g o n TV
Usin g t h e AV co rd le ss IR re ce ive r
Once you connect the AV cordless IR receiver (not supplied) to your TV or VCR, you
can easily view the picture on your TV. For details, refer to the operating instructions of
the AV cordless IR receiver.
LASER LINK
LASER LINK emitter
(1) After connecting your TV and AV cordless IR receiver, set the POWER switch
on the AV cordless IR receiver to ON.
(2) Turn the TV on and set the TV/ VCR selector on the TV to VCR.
(3) Press LASER LINK. The lamp of LASER LINK lights up.
(4) Press ( on your camcorder to start playback.
(5) Point the LASER LINK emitter at the AV cordless IR receiver. Adjust the
position of your camcorder and the AV cordless IR receiver to obtain clear
playback pictures.
To ca n ce l t h e la se r lin k fu n ct io n
Press LASER LINK. The lamp on the LASER LINK button goes out.
If you turn the pow er off
Laser link turns off automatically.
If you use a Sony TV
• You can turn on the TV automatically when you press LASER LINK or (. To do so,
set AUTO TV ON to ON in the MENU settings and turn the TV’s main switch on, then
do either of the following:
– Point the LASER LINK emitter at the TV’s remote sensor and press LASER LINK.
– Turn on LASER LINK and press (.
• You can switch the video input of the TV automatically to the one which the AV
cordless IR receiver is connected. To do so, set AUTO TV ON to ON and TV INPUT to
the same video input (1, 2, 3) in the MENU settings. With some models, however, the
picture and sound may be disconnected momentarily when the video input is
switched.
• The above feature may not work on some TV models.
Note
When laser link is activated (the LASER LINK button is lit), your camcorder consumes
power. Press LASER LINK to turn off the laser link function when it is not needed.
26
— Ad va n ce d Re co rd in g Op e ra t io n s —
Ph o t o re co rd in g
You can record a still picture like a photograph. This mode is useful when you want to
record a picture such as a photograph or when you print a picture using a video printer
(not supplied).
(1) Set the POWER switch to CAMERA.
(2) In the standby mode, keep pressing PHOTO lightly until a still picture
appears. The CAPTURE indicator appears. Recording does not start yet.
To change the still picture, release PHOTO, select a still picture again, and then
press and hold PHOTO lightly.
(3) Press PHOTO deeper.
The still picture in the viewfinder or on the LCD screen is recorded for about
seven seconds. The sound during those seven seconds is also recorded.
During recording, the image you are shooting appears in the viewfinder or on
the LCD screen.
CAPTURE
2
3
1
PHOTO
•••••••
Notes
• During photo recording, you cannot change the mode or setting.
• During photo recording, you cannot turn your camcorder off or press the PHOTO
button.
• The PHOTO button does not work:
– while the digital effect function is set or in use.
– while the fader function is in use.
• When recording a still picture, do not shake your camcorder. The picture may
fluctuate.
To use the photo recording function using the Remote Commander
Press PHOTO in the Remote Commander. Your camcorder record a picture on the LCD
screen or in the viewfinder immediately.
To use the photo recording function during normal CAMERA recording
Press PHOTO deeper. The still picture is then recorded for about seven seconds and
your camcorder returns to the standby mode. You cannot select another still picture.
27
Ph o t o re co rd in g
Prin t in g t h e st ill p ict u re
You can print a still picture by using the video printer (not supplied). Connect the video
printer using the A/ V connecting cable supplied with your camcorder.
Connect the yellow plug of the cable to the VIDEO jack and to the video input of the
video printer. Refer to the operating instructions of the video printer as well.
Video printer
LINE IN
VIDEO S VIDEO
S VIDEO
VIDEO
: Signal flow
If the video printer is equipped w ith S video input
Use the S video connecting cable (not supplied). Connect it to the S VIDEO jack and the
S video input of the video printer.
28
Usin g t h e w id e m o d e
You can record a 16:9 wide picture to watch on the 16:9 wide-screen TV (16:9WIDE).
The picture with black bands at the top and the bottom on the LCD screen or in the
viewfinder [a ] is normal. The picture on a normal TV [b ] is horizontally compressed.
You can watch the picture of normal images on a wide-screen TV [c].
[b ]
[c]
[a ]
16:9WIDE
In the standby mode, set 16:9WIDE to ON in the MENU settings (p. 76).
MENU
To ca n ce l t h e w id e m o d e
Set 16:9WIDE to OFF in the MENU settings.
If the w ide mode is set to ON
The SteadyShot function does not work. If you set 16:9WIDE to ON in the MENU
settings when the SteadyShot function is working,
function does not function.
flashes and the SteadyShot
In the w ide mode
You cannot select the old movie function with DIGITAL EFFECT and the bounce
function with FADER.
During recording
You cannot select or cancel the wide mode.
Connection for a TV
Pictures recorded in the 16:9WIDE mode automatically appear on the TV screen at full
size when:
• you connect your camcorder to a TV that is compatible with the video ID (ID-1/ ID-2)
system.
• you connect your camcorder to the S video jack on the TV.
ID-2 system
The ID-2 system is a system which converts the copyrignt signal to the analog system
with ID-1 signals inserted between video signals.
29
Usin g t h e fa d e r fu n ct io n
You can fade in or out to give your recording a professional appearance.
[a ]
STBY
REC
FADER
M.FADER
(mosaic)
BOUNCE*
(Fade in only)
OVERLAP
(Fade in only)
[b ]
STBY
REC
MONOTONE
When fading in, the picture gradually changes from black-and-white to color.
When fading out the picture gradually changes from color to black-and-white.
* You cannot use this function when D ZOOM is set to ON in the MENU settings.
30
Usin g t h e fa d e r fu n ct io n
(1) When fading in [a ]
In the standby mode, press FADER until the desired fader indicator flashes.
When fading out [b ]
In the recording mode, press FADER until the desired fader indicator flashes.
The indicator changes as follows:
FADER n M.FADER n BOUNCE n MONOTONE n OVERLAP n
no indicator
The last selected fader mode is indicated first of all.
(2) Press START/ STOP. The fader indicator stops flashing.
1
FADER
FADER
To ca n ce l t h e fa d e r fu n ct io n
After the fade in/ out is carried out : Your camcorder automatically returns to the
normal mode.
Before the fade in/ out is carried out : Before pressing START/ STOP, press FADER until
the indicator disappears.
31
Usin g t h e Fa d e r fu n ct io n
Notes
• The overlap function work only for tapes recorded in the Digital8 system.
• You cannot use the following functions while using the fader function. Also, you
cannot use the fader function while using the following functions.
– Digital effect
– Low lux mode of PROGRAM AE (Overlap function only)
– NightShot +Slow shutter
– Photo recording
When the OVERLAP indicator appears
Your camcorder automatically memorizes the image recorded on a tape. As the image is
being memorized, the OVERLAP indicator flashes fast, and the playback picture is
displayed. At this stage, the picture may not be recorded clearly, depending on the tape
condition.
When START/STOP MODE is set to
or 5SEC
You cannot use the fader function.
While using the bounce function, you cannot use the follow ing functions:
– Exposure
– Focus
– Zoom
– Picture effect
Note on the bounce function
The BOUNCE indicator does not appear in the following mode or functions:
– D ZOOM is set to ON in the MENU settings
– Wide mode
– Picture effect
– PROGRAM AE
32
Usin g sp e cia l e ffe ct s – Pict u re e ffe ct
You can digitally process images to obtain special effects like those in films or on the
TV.
NEG. ART [a ] : The color and brightness of the picture is reversed.
SEPIA :
The picture is sepia.
B&W :
The picture is monochrome (black-and-white).
SOLARIZE [b ] : The light intensity is clearer, and the picture looks like an illustration.
SLIM [c] : The picture expands vertically.
STRETCH [d ] : The picture expands horizontally.
PASTEL [e ] : The contrast of the picture is emphasized, and the picture looks like an
animated cartoon.
MOSAIC [f] : The picture is mosaic.
[a ]
[b ]
[c]
[d ]
[e ]
[f]
(1) Press PICTURE EFFECT in the standby or recording mode.
The picture effect indicator appears.
(2) Turn the SEL/ PUSH EXEC dial to select the desired picture effect mode.
The indicator changes as follows:
NEG.ART ˜ SEPIA ˜ B&W ˜ SOLARIZE ˜ SLIM ˜ STRETCH ˜
PASTEL ˜ MOSAIC
PICTURE EFFECT
2
NEG. ART
To t u rn t h e p ict u re e ffe ct fu n ct io n o ff
Press PICTURE EFFECT.
While using the picture effect function
You cannot select the old movie mode with DIGITAL EFFECT.
When you turn the pow er off
Your camcorder automatically returns to the normal mode.
33
Usin g sp e cia l e ffe ct s – Dig it a l e ffe ct
You can add special effects to recorded pictures using the various digital functions. The
sound is recorded normally.
STILL
You can record a still picture so that it is superimposed on a moving picture.
FLASH (FLASH MOTION)
You can record still pictures successively at constant intervals.
LUMI. (LUMINANCEKEY)
You can swap a brighter area in a still picture with a moving picture.
TRAIL
You can record the picture so that an incidental image like a trail is left.
SLOW SHTR (SLOW SHUTTER)
You can slow down the shutter speed. The slow shutter mode is good for recording
dark pictures more brightly. However, the picture may be less clear.
OLD MOVIE
You can add an old movie type atmosphere to pictures. Your camcorder automatically
sets the wide mode to ON, picture effect to SEPIA, and the appropriate shutter speed.
Still picture
Moving picture
STILL
LUMI.
Still picture
Moving picture
34
Usin g sp e cia l e ffe ct s – Dig it a l e ffe ct
(1) While your camcorder is in the standby or recording mode, press DIGITAL
EFFECT. The digital effect indicator appears.
(2) Turn the SEL/ PUSH EXEC dial to select the desired digital effect mode.
The indicator changes as follows:
STILL ˜ FLASH ˜ LUMI. ˜ TRAIL ˜ SLOW SHTR ˜ OLD MOVIE
(3) Press the SEL/ PUSH EXEC dial. The indicator lights up and the bars appear.
In the STILL and LUMI. modes, the still picture is stored in memory.
(4) Turn the SEL/ PUSH EXEC dial to adjust the effect.
Items to adjust
STILL
The rate of the still picture you want to superimpose on the moving
picture
FLASH
LUMI.
The interval of flash motion
The color scheme of the area in the still picture which is to be
swapped with a moving picture
TRAIL
The vanishing time of the incidental image
SLOW SHTR
Shutter speed. The larger the shutter speed number, the slower the
shutter speed.
OLD MOVIE
No adjustment necessary
The more bars there are on screen, the stronger the digital effect. The bars appear in the
following modes: STILL, FLASH, LUMI. and TRAIL.
3
LUMI.
1
2
DIGITAL
EFFECT
4
LUMI.
To ca n ce l t h e d ig it a l e ffe ct
Press DIGITAL EFFECT. The digital effect indicator disappears.
35
Usin g sp e cia l e ffe ct s – Dig it a l Effe ct
Notes
• The following functions do not work during digital effect:
– Fader
– Low lux mode of PROGRAM AE
– Photo recording
– NightShot +Slow shutter
• The following functions do not work in the slow shutter mode:
– Exposure
– PROGRAM AE
• The following functions do not work in the old movie mode:
– Exposure
– Wide mode
– Picture effect
– PROGRAM AE
When you turn the pow er off
The digital effect will be automatically canceled.
When recording in the slow shutter mode
Auto focus may not be effective. Focus manually using a tripod.
Shutter speed
Shutter speed number
SLOW SHTR 1
SLOW SHTR 2
SLOW SHTR 3
SLOW SHTR 4
Shutter speed
1/ 30
1/ 15
1/ 8
1/ 4
36
Usin g t h e PROGRAM AE fu n ct io n
You can select PROGRAM AE (Auto Exposure) mode to suit your specific shooting
requirements.
Spotlight mode
This mode prevents people’s faces, for example, from appearing excessively white
when shooting subjects lit by strong light at weddings or in the theater.
a Soft portrait mode
This mode brings out the subject while creating a soft background for subjects such as
people or flowers, and faithfully reproduces skin color.
A
Sports lesson mode
This mode minimizes shake on fast-moving subjects such as in tennis or golf.
Beach & ski mode
This mode prevents people’s faces from appearing dark in strong light or reflected light,
such as at a beach in midsummer or on a ski slope.
Sunset & moon mode
This mode allows you to maintain atmosphere when you are recording sunsets, general
night views, fireworks displays and neon signs.
Landscape mode
This mode is for when you are recording distant subjects such as mountains and
prevents your camcorder from focusing on glass or metal mesh in windows when you
are recording a subject behind glass or a screen.
Low lux mode
This mode makes subjects brighter in insufficient light.
37
Usin g t h e PROGRAM AE fu n ct io n
(1) Press PROGRAM AE in the standby mode. The PROGRAM AE indicator
appears.
(2) Turn the SEL/ PUSH EXEC dial to select the desired PROGRAM AE mode.
The indicator changes as follows:
PROGRAM
1
2
A
To t u rn t h e PROGRAM AE fu n ct io n o ff
Press PROGRAM AE.
Notes
• In the spotlight, sports lesson and beach & ski modes, you cannot take close-ups. This
is because your camcorder is set to focus only on subjects in the middle to far distance.
• In the sunset & moon and landscape modes, your camcorder is set to focus only on
distant subjects.
• The following functions do not work in the PROGRAM AE mode:
– Slow shutter
– Old movie
– Bounce
• The following functions do not work in the low lux mode:
– Digital effect
– Overlap
– Exposure
• If you press PROGRAM AE when using the NightShot function, the PROGRAM AE
indicator flashes and the PROGRAM AE function does not work.
If you are recording under a discharge tube such as a fluorescent lamp, sodium
lamp or mercury lamp
Flickering or changes in color may occur in the following modes. If this happens, turn
the PROGRAM AE function off.
– Soft portrait mode
– Sports lesson mode
38
Ad ju st in g t h e e xp o su re m a n u a lly
You can manually adjust and set the exposure. When you turn your camcorder on, it
will automatically be in the automatic exposure mode. This mode works to record
subjects so that they are recorded slightly brighter than they actually are.
Adjust the exposure manually in the following cases:
• The subject is backlit
• Bright subject and dark background
• To record dark pictures (e.g. night scenes) faithfully
(1) Press EXPOSURE in the standby or recording mode.
The exposure indicator appears.
(2) Turn the SEL/ PUSH EXEC dial to adjust the brightness.
1
EXPOSURE
–
+
2
To re t u rn t o t h e a u t o m a t ic e xp o su re m o d e
Press EXPOSURE again.
Note
When you adjust the exposure manually, the following function and modes do not
work:
– Backlight
– Slow shutter
– Old movie
If you change the PROGRAM AE mode or slide NIGHTSHOT to ON
Your camcorder automatically returns to the automatic exposure mode.
39
Fo cu sin g m a n u a lly
You can gain better results by manually adjusting the focus in the following cases:
• The autofocus mode is not effective when shooting
– subjects through glass coated with water droplets
– horizontal stripes
– subjects with little contrast with backgrounds such as walls and sky
• When you want to change the focus from a subject in the foreground to a subject in the
background
• Shooting a stationary subject when using a tripod
(1) Set FOCUS to MANUAL in the standby or recording mode. The f indicator
appears.
(2) Turn the focus ring to sharpen focus.
2
FOCUS
PUSH AUTO
To re t u rn t o t h e a u t o fo cu s m o d e
Set FOCUS to AUTO.
To re co rd d ist a n t su b je ct s
When you press FOCUS down to INFINITY. The lens focuses on and
indicator
appears. When you release FOCUS, your camcorder returns to the manual focus mode.
Use this mode when your camcorder focuses on near objects even though you are
trying to shoot a distant object.
To sh o o t w it h a u t o fo cu sin g m o m e n t a rily
Press PUSH AUTO.
The auto focus functions while you are pressing PUSH AUTO.
Use this button to focus on one subject and then another with smooth focusing.
When you release PUSH AUTO, manual focusing resumes.
Shooting in relatively dark places or shooting fast-moving subjects in relatively
bright places
Shoot at the “W” (wide-angle) position after focusing at the “T” (telephoto) position.
When you shoot close to the subject
Focus at the end of the “W” (wide-angle) position.
The follow ing indicators may appear
when recording a distant subject.
when the subject is too close to focus on.
40
In se rt in g a sce n e
You can insert a scene in the middle of a recorded tape by setting the start and end
points. The previously recorded frames between these start and end points will be
erased. Use the Remote Commander for this operation.
[a ]
[b ]
(1) While your camcorder is in the standby mode, keep pressing EDITSEARCH,
and release the button at the insert end point [b ].
(2) Press ZERO SET MEMORY. The ZERO SET MEMORY indicator flashes and
the tape counter resets to zero.
(3) Keep pressing the РΠside of EDITSEARCH and release the button at the
insert start point [a ].
(4) Press START/ STOP to start recording. The scene is inserted. Recording stops
automatically at the tape counter zero point. Your camcorder returns to the
standby mode.
EDITSEARCH
ZERO SET
MEMORY
Notes
• The zero set memory function works only for tapes recorded in the Digital8 system.
• The picture and the sound may be distorted at the end of the inserted section when it
is played back.
If you re-record on the section w hich contains a non-recorded section
The zero set memory function may not work correctly.
When START/STOP MODE is set to
or 5SEC
You cannot use the zero set memory function.
41
— Ad va n ce d Pla yb a ck Op e ra t io n s —
Pla yin g b a ck a t a p e w it h p ict u re e ffe ct s
During playback, you can process a scene using the picture effect functions: NEG.ART,
SEPIA, B&W and SOLARIZE.
During playback, press PICTURE EFFECT and turn the SEL/ PUSH EXEC dial until the
desired picture effect indicator (NEG.ART, SEPIA, B&W or SOLARIZE) flashes.
For details of each picture effect function, see page 33.
PICTURE EFFECT
NEG. ART
To ca n ce l t h e p ict u re e ffe ct fu n ct io n
Press PICTURE EFFECT.
Notes
• The picture effect function works only for tapes recorded in the Digital8 system.
• You cannot process externally input scenes using the picture effect function.
• To record pictures that you have processed using the picture effect function, record
the pictures on the VCR.
Pictures processed by the picture effect function
Pictures processed by the picture effect function are not output through the DV IN/
OUT jack.
When you set the POWER sw itch to OFF or stop playing back
The picture effect function is automatically canceled.
42
Pla yin g b a ck a t a p e w it h d ig it a l e ffe ct s
During playback, you can process a scene using the digital effect functions: STILL,
FLASH, LUMI. and TRAIL.
(1) During playback, press DIGITAL EFFECT and turn the SEL/ PUSH EXEC dial
until the desired digital effect indicator (STILL, FLASH, LUMI. or TRAIL)
flashes.
(2) Press the SEL/ PUSH EXEC dial.
The digital effect indicator lights up and the bars appear. In the STILL or
LUMI. mode, the picture where you press the SEL/ PUSH EXEC dial is stored
in memory as a still picture.
(3) Turn the SEL/ PUSH EXEC dial to adjust the effect.
For details of each digital effect function, see page 34.
3
STILL
1
DIGITAL
EFFECT
4
2
STILL
To ca n ce l t h e d ig it a l e ffe ct fu n ct io n
Press DIGITAL EFFECT.
Notes
• The digital effect function works only for tapes recorded in the Digital8 system.
• You cannot process scenes from externally input scenes using the digital effect
function.
• To record picture that you have processed using the digital effect function, record the
pictures on the VCR.
Pictures processed by the digital effect function
Pictures processed by the digital effect function are not output through the DV IN/
OUT jack.
When you set the POWER sw itch to OFF or stop playing back
The digital effect function is automatically canceled.
43
Qu ickly lo ca t in g a sce n e u sin g t h e ze ro
se t m e m o ry fu n ct io n
Your camcorder goes forward or backward to automatically stop at a desired scene
having a tape counter value of “0:00:00”. Use the Remote Commander for this
operation.
Use this function, for example, to view a desired scene later on during playback.
(1) In the playback mode, press DISPLAY.
(2) Press ZERO SET MEMORY at the point you want to locate later. The tape
counter shows “0:00:00” and the ZERO SET MEMORY indicator flashes.
(3) Press p when you want to stop playback.
(4) Press 0 to rewind the tape to the tape counter’s zero point. The tape stops
automatically when the tape counter reaches approximately zero. The ZERO
SET MEMORY indicator disappears and the time code appears.
(5) Press (. Playback starts from the tape counter’s zero point.
DISPLAY
ZERO SET MEMORY
Notes
• The zero set memory function works only for tapes recorded in the Digital8 system.
• When you press ZERO SET MEMORY before rewinding the tape, the zero set memory
function will be canceled.
• There may be a discrepancy of several seconds from the time code.
• The zero set memory function may not work when there is a blank portion between
pictures on a tape.
44
Se a rch in g a re co rd in g b y d a t e
You can automatically search for the point where the recording date changes and start
playback from that point (Date search). Use the Remote Commander for this operation.
Use this function to check where recording dates change or to edit the tape at each
recording date.
JUL 4 1999
JUL 5 1999
DEC 31 1999
V
V
V
[a ]
[b ]
[c]
(1) Set the POWER switch to VTR.
(2) Press SEARCH MODE on the Remote Commander repeatedly, until the date
search indicator appears.
The indicator changes as follows:
DATE SEARCH n PHOTO SEARCH n PHOTO SCAN n no indicator
(3) When the current position is [b ], press = to search towards [a ] or press +
to search towards [c]. Your camcorder automatically starts playback at the
point where the date changes.
Each time you press = or +, the camcorder searches for the previous or
next date.
DATE
SEARCH
00
SEARCH
MODE
2
DATE
SEARCH
01
3
=
+
To st o p se a rch in g
Press p.
45
Se a rch in g a re co rd in g b y d a t e
Notes on the date seach mode
• The date search works only for tapes recorded in the Digital8 system.
• If one day’s recording is less than one minute, your camcorder may not accurately
find the point where the recording date changes.
If a tape has a blank portion in the recorded portions
The date search function will not work correctly.
46
Se a rch in g fo r a p h o t o – Ph o t o se a rch /
Ph o t o sca n
You can search for the recorded still picture (photo search).
You can also search for still pictures one after another and display each picture for five
seconds automatically (photo scan). Use the Remote Commander for these operations.
Se a rch in g fo r a p h o t o
(1)Set the POWER switch to VTR.
(2)Press SEARCH MODE on the Remote Commander repeatedly, until the photo
search indicator appears.
The indicator changes as follows:
DATE SEARCH n PHOTO SEARCH n PHOTO SCAN n no indicator
(3)Press = or + to select the photo for playback. Each time you press = or +,
the camcorder searches for the previous or next photo. Your camcorder
automatically starts playback from the photo.
2
SEARCH
MODE
PHOTO
SEARCH
00
3
=
+
PHOTO
SEARCH
01
To st o p se a rch in g
Press p.
If a tape has a blank portion in the recorded portions
The photo search function may not work correctly.
47
Se a rch in g fo r a p h o t o – Ph o t o se a rch /Ph o t o sca n
Sca n n in g p h o t o
(1)Set the POWER switch to VTR.
(2)Press SEARCH MODE on the Remote Commander repeatedly, until the photo scan
indicator appears.
The indicator changes as follows:
DATE SEARCH n PHOTO SEARCH n PHOTO SCAN n no indicator
(3)Press = or +.
Each photo is played back for about 5 seconds automatically.
SEARCH
MODE
2
PHOTO
00
SCAN
=
+
3
To st o p sca n n in g
Press p.
Note
The photo search and photo scan work only for tapes recorded in the Digital8 system.
48
— Ed it in g o n Ot h e r Eq u ip m e n t —
Du b b in g a t a p e
Usin g t h e A/V co n n e ct in g ca b le o r S vid e o co n n e ct in g ca b le
(n o t su p p lie d )
Connect your camcorder to the VCR using the A/ V connecting cable supplied with
your camcorder.
Set the input selector on the VCR to LINE, if available.
(1) Insert a blank tape (or a tape you want to record over) into the VCR, and insert
the recorded tape into your camcorder.
(2) Set the POWER switch to VTR.
(3) Play back the recorded tape on your camcorder.
(4) Start recording on the VCR.
S VIDEO
VIDEO
IN
S VIDEO
VIDEO
AUDIO
AUDIO
: Signal flow
Wh e n yo u h a ve fin ish e d d u b b in g a t a p e
Press p on both your camcorder and the VCR.
If you have displayed the screen indicators on the TV
Make the indicators disappear by pressing SEARCH MODE on the Remote
Commander, DISPLAY or DATA CODE so that they will not be superimposed on the
edited tape.
You can edit on VCRs that support the follow ing systems
h 8 mm, H Hi8, j VHS, k S-VHS, VHSC, K S-VHSC, l Betamax,
¬ ED Betamax,
mini DV,
DV or Digital8
If your VCR is a monaural type
Connect the yellow plug for video and the white plug for audio on both your
camcorder and the VCR. You do not need to connect the red plug. With this connection,
the sound will be monaural.
Connect using an S video cable (not supplied) to obtain high-quality pictures
With this connection, you do not need to connect the yellow (video) plug of the A/ V
connecting cable.
Connect an S video cable (not supplied) to the S video jacks of both your camcorder and
the VCR.
To perform a more precise editing
Connect a LANC cable (not supplied) to your camcorder and other video equipment
having fine synchro-editing function, using this camcorder as a player.
49
Du b b in g a t a p e
Usin g t h e i.LINK ca b le
Simply connect the VMC-IL4415/ IL4435/ 2DV/ 4DV i.LINK cable (not supplied) to
DV IN/ OUT and to DV IN/ OUT of the DV products. With digital-to-digital
connection, video and audio signals are transmitted in digital form for high-quality
editing. You can dub the screen indicators.
(1) Insert a blank tape (or a tape you want to record over) into the VCR, and insert
the recorded tape into your camcorder.
(2) Set the POWER switch to VTR.
(3) Play back the recorded tape on your camcorder.
(4) Start recording on the VCR.
DV
S VIDEO
LANC
DV IN/ OUT
(not supplied)
DV IN/ OUT
: Signal flow
Wh e n yo u h a ve fin ish e d d u b b in g a t a p e
Press p on both your camcorder and the VCR.
Note on tapes that are not recorded in the Digital8 system
The picture may fluctuate. This is not a malfunction.
During playback of tapes recorded in the Hi8/standard 8 system
Digital signals are output as the image signals from the DV IN/ OUT jack.
You can connect one VCR only using the i. LINK cable.
During digital editting
You cannot use DIGITAL EFFECT button functions.
You can also use your camcorder as a recorder
• You can use your camcorder as a player or recorder without changing the connection.
In this case, the DV IN indicator appears in the viewfinder or on screen. The DV IN
indicator may appear on both equipment.
• When using your camcorder as a recorder, the color balance may be incorrect on the
monitor screen. This, however, is not recorded on the tape.
If you record playback pause picture via the DV jack
The recorded picture becomes rough. Also, when you play back the recorded pictures
on other video equipment, the picture may jitter.
50
Re co rd in g vid e o o r TV p ro g ra m s
You can record a tape from another VCR or a TV program from a TV that has video/
audio outputs. Use your camcorder as a recorder. Turn down the volume of your
camcorder. Otherwise, the picture may be distorted.
(1) Insert a blank tape (or a tape you want to record over) into your camcorder. If
you are recording a tape from the VCR, insert a recorded tape into the VCR.
(2) Set the POWER switch to VTR.
(3) Set DISPLAY to LCD in the MENU settings (p. 76). The picture from a TV or
VCR appears in the viewfinder or on the LCD screen.
(4) Press r REC and the button on its right simultaneously on your camcorder,
then immediately press P on your camcorder.
(5) Press ( on the VCR to start playback if you are recording a tape from VCR.
Select a TV program if you are recording from TV.
(6) Press P on your camcorder at the scene where you want to start recording
from.
4
PAUSE
REC
S VIDEO
VIDEO
OUT
S VIDEO
AUDIO
VIDEO
AUDIO
: Signal flow
Notes
• To enable smooth transition, we recommend that you do not mix pictures recorded in
the Hi8/ standard 8 with the Digital8 system on a tape.
• If you fast-forward or slow-playback on the other equipment, be sure to play back the
original tape at normal speed.
If your VCR is a monaural type
Connect the yellow plug for video and the white plug for audio on both your
camcorder and the VCR (you do not need to connect the red plug). With this
connection, the sound will be monaural.
Connect using an S video cable (not supplied) to obtain high-quality pictures
With this connection, you do not need to connect the yellow (video) plug of the A/ V
connecting cable.
Connect an S video cable (not supplied) to the S video jacks of both your camcorder and
VCR.
If your VCR or TV does not have an S video out jack, do not connect an S video cable
(not supplied) to your camcorder. If you connect an S video cable, the picture may not
appear on screen.
51
In se rt in g a sce n e fro m a VCR
Re p la cin g re co rd in g o n a t a p e – In se rt Ed it in g
You can insert a new scene from a VCR onto your originally recorded tape by
specifying the insert start and end points. Use the Remote Commander for this
operation. Connections are the same as in “Recording video or TV programs” on page
51.
Insert a cassette containing the desired scene to insert into the VCR.
[a ]
[b ]
[c]
52
In se rt in g a sce n e fro m a VCR
(1)Set the POWER switch to VTR.
(2)On the VCR, locate just before the insert start point [a ], then press P to set the VCR
to the playback pause mode.
(3)On your camcorder, locate the insert end point [c] by pressing 0 or ). Then
press P to set it to the playback pause mode.
(4)Press ZERO SET MEMORY on the Remote Commander. The ZERO SET MEMORY
indicator flashes and the end point of the insert is stored in memory.
(5)On your camcorder, locate the insert start point [b ] by pressing 0, then press
two r REC buttons at same time to set your camcorder to the recording pause
mode.
(6)First press P on the VCR, and after a few seconds press P on your camcorder to
start inserting the new scene.
Inserting automatically stops near the zero point on the tape counter. Your
camcorder automatically returns to the recording pause mode.
5
REC
0:00:00
4
ZERO SET
ZERO SET
MEMORY
MEMORY
To ch a n g e t h e in se rt e n d p o in t
Press ZERO SET MEMORY again after step 5 to erase the ZERO SET MEMORY
indicator and begin from step 3.
Notes
• The zero set memory function works only for tapes recorded in the Digital8 system.
• The picture and sound recorded on the section between the insert start and end points
will be erased when you insert the new scene.
When the inserted picture is played back
The picture may be distorted at the end of the inserted section. This is not a
malfunction.
To insert a scene w ithout setting the insert end point
Skip step 3 and 4. Press p when you want to stop inserting.
53
— Fla sh Me m o ry Op e ra t io n s —
Using the flash m em ory function – introduction
Your camcorder has a built-in flash memory with a capacity of 2MB.
The built-in flash memory can record still images, exchange still image data with tapes
and play back and delete the still image data. If you use the supplied accessories, you
can input still image data to your PC. This chapter explains the functions that are
available using the built-in flash memory.
On file format (JPEG)
This unit compresses image data in JPEG format (extension .jpg) with thumbnail data
for the index screen. The index screen data is visible only on this unit.
Typical image data file name
ex. DSC00001.jpg
During recording in the built-in flash memory
Do not turn the power off nor remove the battery pack.
You can record only still images in the built-in flash memory. You cannot record
sounds.
When using a video light (not supplied) or similar equipment mounted on the
intelligent accessory shoe
Recording an image in the built-in flash memory may result in a temporary power
shortage in the accessory shoe, causing the video light to go out. This is not a
malfunction.
If the MEMORY FULL indicator
appears in the view finder or on the LCD screen
You cannot use the built-in flash memory. See “Warning indicators and messages”
(p. 92) for more information.
54
Usin g t h e fla sh m e m o ry fu n ct io n – in t ro d u ct io n
Se le ct in g t h e im a g e q u a lit y m o d e – QUALITY
You can select the image quality mode in still picture recording. If you do not make any
selection, your camcorder automatically records in STANDARD mode.
(1) Set the POWER switch to CAMERA.
(2) Turn STANDBY to MEMORY.
(3) Press MENU to display the MENU settings.
(4) Turn the SEL/ PUSH EXEC dial to select
, then press the dial.
(5) Turn the SEL/ PUSH EXEC dial to select QUALITY, then press the dial.
(6) Turn the SEL/ PUSH EXEC dial to select the desired image quality, then press
the dial.
Press MENU to make the MENU settings disappear.
K
MEMORY SET
POWER
CONTINUOUS
QUAL I TY
1
2
4
5
6
CAMERA
OFF
FLD. / FRAME
PROTECT
SLIDE SHOW
DELETE ALL
FORMAT
VTR
START/STOP
[
]
:
MENU END
MEMORY SET
CONTINUOUS
QUAL I TY
FLD. / FRAME
PROTECT
F I NE
SLIDE SHOW
DELETE ALL
FORMAT
RETURN
[
]
:
MENU END
MEMORY SET
CONTINUOUS
QUAL I TY
FLD. / FRAME F I NE
PROTECT
STANDARD
SLIDE SHOW
DELETE ALL
FORMAT
3
MENU
RETURN
[
]
:
MENU END
Im a g e q u a lit y se t t in g s
Setting
Meaning (indicator on the screen)
STANDARD
This is the standard image quality. The image is compressed to
about 1/ 10. (STD)
FINE
Use this mode when you want to record high quality images. The
image is compressed to about 1/ 6. (FINE)
55
Usin g t h e fla sh m e m o ry fu n ct io n – in t ro d u ct io n
Differences in image quality mode
Recorded images are compressed in JPEG format before being stored into the memory.
The memory capacity allotted to each image varies depending on the selected image
quality mode. Details are shown in the table below. (The number of pixels is 640 × 480,
regardless of image quality mode. The data size before compression is about 600 KB.)
Image quality mode
FINE
Memory capacity
About 100 KB
About 60 KB
Recordable number of images*
About 20 images
STANDARD
About 33 images
* Depending on the complexity of the subject.
Note
In some cases, changing the image quality mode may not affect the image quality,
depending on the types of images you are shooting.
56
Usin g t h e fla sh m e m o ry fu n ct io n – in t ro d u ct io n
Se le ct in g t h e re co rd in g m o d e – FIELD/FRAME
You can select the recording mode in still picture recording. If you do not make any
selection, your camcorder automatically records in FIELD mode.
(1) Set the POWER switch to CAMERA.
(2) Turn STANDBY to MEMORY.
(3) Press MENU to display the MENU settings.
(4) Turn the SEL/ PUSH EXEC dial to select
, then press the dial.
(5) Turn the SEL/ PUSH EXEC dial to select FLD./ FRAME, then press the dial.
(6) Turn the SEL/ PUSH EXEC dial to select the desired recording mode, then
press the dial.
Press MENU to make the MENU settings disappear.
K
MEMORY SET
POWER
CONTINUOUS
QUAL I TY
1
2
4
5
6
CAMERA
OFF
FLD. / FRAME
PROTECT
SLIDE SHOW
DELETE ALL
FORMAT
VTR
START/STOP
[
]
:
MENU END
MEMORY SET
CONTINUOUS
QUAL I TY
FLD. / FRAME F I ELD
PROTECT
SLIDE SHOW
DELETE ALL
FORMAT
RETURN
[
]
:
MENU END
MEMORY SET
CONTINUOUS
QUAL I TY
FLD. / FRAME F I ELD
PROTECT
FRAME
SLIDE SHOW
DELETE ALL
FORMAT
3
MENU
RETURN
[
]
:
MENU END
Re co rd in g m o d e se t t in g s
Setting
Meaning (indicator on the screen)
FIELD
Field recording. Your camcorder compensates for camera-shake.
(no indicator)
FRAME
Frame recording. Your camcorder records images in high quality.
(FRAME)
Note
When recording fast-moving subjects in FRAME mode, the recorded image is blurry.
57
Re co rd in g st ill im a g e s in t h e b u ilt -in fla sh
m e m o ry – Me m o ry p h o t o re co rd in g
You can store still images in the built-in flash memory.
(1) Set the POWER switch to CAMERA.
(2) Turn STANDBY to MEMORY.
(3) Keep pressing PHOTO lightly. The picture freezes and the CAPTURE
indicator appears in the vienfinder or on the LCD screen. Recording does not
start yet.
(4) Press PHOTO deeper. The image displayed on the screen will be recorded in
the built-in flash memory. Recording is complete when the bar scroll indicator
disappears.
K
POWER
1
3
2
CAMERA
OFF
VTR
START/STOP
STD
1 / 3 3
CAPTURE
STD
4
PHOTO
PHOTO
When the STANDBY sw itch is set to MEMORY
The following functions do not work:
– Wide mode
– Digital effect
– Picture effect
– Nightshot + Slow shutter
– Low lux mode of PROGRAM AE
When you are recording a still image
You can neither turn off the power nor press PHOTO.
When you press the PHOTO button on the Remote Commander
Your camcorder immediately records the image that is on the screen when you press
the button.
58
Re co rd in g st ill im a g e s in t h e b u ilt -in fla sh m e m o ry – Me m o ry
p h o t o re co rd in g
Re co rd in g im a g e s co n t in u o u sly
You can record still pictures continuously. Select one of the two modes in the MENU
settings (p. 76) before recording.
Continuous mode (CONTINUOUS: ON) [a ]
You can record 3 or 4 pictures continuously.
Multi screen mode (CONTINUOUS: MULTI SCRN) [b ]
You can record 9 still pictures continuously on a single page.
[a ]
[b ]
59
Re co rd in g st ill im a g e s in t h e b u ilt -in fla sh m e m o ry – Me m o ry
p h o t o re co rd in g
(1) Set the POWER switch to CAMERA.
(2) Turn STANDBY to MEMORY.
(3) Press MENU to display the MENU settings.
(4) Turn the SEL/ PUSH EXEC dial to select
, then press the dial.
(5) Turn the SEL/ PUSH EXEC to select CONTINUOUS, then press the dial.
(6) Turn the SEL/ PUSH EXEC to select the desired setting, then press the dial.
(7) Press MENU to make the MENU settings disappear.
POWER
1
CAMERA
OFF
VTR
K
2
START/STOP
MEMORY SET
CONTINUOUS
QUAL I TY
4
3
FLD.
/
FRAME
MENU
PROTECT
SLIDE SHOW
DELETE ALL
FORMAT
[
]
:
MENU END
MEMORY SET
CONTINUOUS
QUAL I TY
MEMORY SET
CONTINUOUS OFF
OFF
QUAL I TY
ON
5
6
FLD.
/
FRAME
FLD.
/
FRAME MULTI SCRN
PROTECT
PROTECT
SLIDE SHOW
DELETE ALL
FORMAT
SLIDE SHOW
DELETE ALL
FORMAT
RETURN
RETURN
[
]
:
[
]
:
MENU END
MENU END
MEMORY SET
CONTINUOUS
QUAL I TY
ON
FLD.
/
FRAME
PROTECT
SLIDE SHOW
DELETE ALL
FORMAT
RETURN
[
]
:
MENU END
Co n t in u o u s sh o o t in g se t t in g s
Setting
OFF
Meaning (indicator on the screen)
The unit shoots one image at a time. (no indicator)
ON
The unit shoots 3 or 4 still images at about 1 sec intervals. (
)
MULTI SCRN
The unit shoots 9 still images at about 0.3 sec intervals and
displays the images on a single page divided into 9 boxes. (
)
Number of images in continuous shooting
The number of images you can shoot continuously varies depending on the image
quality mode.
FINE:
3 images
STANDARD: 4 images
60
Re co rd in g a n im a g e fro m a re co rd e d
t a p e a s a st ill im a g e
Your camcorder can read moving picture data recorded on a tape and record it as a still
image in the built-in flash memory. The unit can also take in moving picture data
through the input connector and record it as a still image in the built-in flash memory.
Before operation
Insert a recorded tape.
(1) Set the POWER switch to VTR.
(2) Press (. The picture recorded on the tape is played back.
(3) Keep pressing PHOTO lightly until the picture from the tape freezes. The
CAPTURE indicator appears in the viewfinder or on the LCD screen.
Recording does not start yet.
(4) Press PHOTO deeper. The image displayed on the screen will be recorded in
the built-in flash memory. Recording is complete when the bar scroll indicator
disappears.
POWER
1
3
2
PLAY
CAMERA
OFF
VTR
STD
1 / 3 3
CAPTURE
STD
4
PHOTO
PHOTO
If you press PHOTO w hile playing back tapes recorded in the Hi8/standard 8
system
The CAPTURE indicator appears without freezing the image.
Recording a still image from a tape immediately after turning on the pow er
Saving the data may take a little more time than usual. This is not a malfunction.
61
Re co rd in g a n im a g e fro m a re co rd e d t a p e a s a st ill im a g e
Re co rd in g a st ill im a g e fro m o t h e r e q u ip m e n t
When recording the image through the DV IN/OUT jack
(not supplied)
: Signal flow
When recording the image through the AUDIO/VIDEO jack
S video connecting cable
(not supplied)
OUT
S VIDEO
VIDEO
A/ V connecting cable
: Signal flow
(1) Set the POWER switch to VTR and set DISPLAY to LCD in the MENU settings
(p. 76).
(2) Play back the recorded tape, or turn the TV on to see the desired program.
(3) Follow the steps 3 and 4 on page 61.
62
Co p yin g st ill im a g e s fro m a re co rd e d
t a p e – PHOTO SAVE
Using the search function, you can automatically take in only the still images from
tapes and record them in the built-in flash memory in sequence.
Before operation
Insert a recorded tape and rewind the tape.
(1) Set the POWER switch to VTR.
(2) Press MENU to display the MENU settings.
(3) Turn the SEL/ PUSH EXEC to select
, then press the dial.
(4) Turn the SEL/ PUSH EXEC to select PHOTO SAVE, then press the dial. The
PHOTO BUTTON indicator appears on the LCD screen.
(5) Press PHOTO deeper. The still image from the tape is recorded in the built-in
flash memory. The number of still images copied is displayed. The END
indicator is displayed when copying is completed.
POWER
1
CAMERA
OFF
VTR
(
PHOTO SAVE
0 : 0 0 : 0 0 : 0 0
PHOTO SAVE
0 : 1 0 : 2 5 : 3 4
4 / 3 3
STD
8 / 3 3
STD
5
MENU
2
3
4
SAVING
0
END
PHOTO
4
[
]
:
[
]
:
MENU END
MENU END
MEMORY SET
QUALITY
PROTECT
DELETE ALL
FORMAT
PHOTO SAVE
[
]
:
MENU END
MEMORY SET
QUALITY
(
0 : 0 0 : 0 0 : 0 0
PHOTO SAVE
PROTECT
4 / 3 3
STD
DELETE ALL
FORMAT
PHOTO SAVE READY
RETURN
PHOTO BUTTON
[
]
:
[
] :
[
] :
MENU END
PHOTO START MENU END
To st o p co p yin g
Press MENU.
63
Co p yin g st ill im a g e s fro m a re co rd e d t a p e
– Ph o t o sa ve
Note
Photo save function works only for tapes recorded in the Digital8 system.
To record all the images recorded on the tape
Rewind the tape all the way back and start copying.
64
Vie w in g a st ill p ict u re – Me m o ry p h o t o
p la yb a ck
You can play back still images recorded in the built-in flash memory. You can also play
back 6 images at a time by selecting the index screen.
(1) Set the POWER switch to CAMERA.
(2) Turn STANDBY to MEMORY.
(3) While pressing OPEN, open the LCD panel.
(4) Press MEMORY PLAY. The last recorded image is displayed.
(5) Press MEMORY +/ – to select the desired still image. To see the previous
image, press MEMORY –. To see the next image, press MEMORY +.
K
POWER
1
4
2
CAMERA
OFF
VTR
START/STOP
3
5
PLAY
To st o p m e m o ry p h o t o p la yb a ck
Press MEMORY PLAY again.
To play back recorded images on a TV screen
• Connect your camcorder to the TV with the supplied A/ V connecting cable before
operation.
• When operating memory photo playback on a TV or the LCD screen, the image
quality may appear to have deteriorated. This is not a malfunction. The image data is
as good as ever.
• Turn the audio volume of the TV down before operation, or noise (howling) may be
output from the TV speakers.
65
Vie w in g a st ill p ict u re – Me m o ry p h o t o p la yb a ck
Scre e n in d ica t o rs d u rin g st ill im a g e p la yb a ck
Image quality mode
Image number/ Total numbers of recorded
images
6 / 33
MEMORY PLAY
FINE
DSC00006
Protect indicator
Data file name
Pla yin g b a ck 6 re co rd e d im a g e s a t a t im e (in d e x scre e n )
You can play back 6 recorded images at a time. This function is especially useful when
searching for a particular image.
MEMORY
PLAY
INDEX
DELETE
MEMORY INDEX
Press MEMORY INDEX.
A red ” mark appears above the image that is displayed before changing to the index
screen mode.
1
4
2
3
5
6
” mark
DSC00006
6 / 33
• To display the following 6 images, keep pressing MEMORY +.
• To display the previous 6 images, keep pressing MEMORY –.
To re t u rn t o t h e n o rm a l p la yb a ck scre e n (sin g le scre e n )
Press MEMORY +/ – to move the ” mark to the image you want to display on full
screen, then press MEMORY PLAY.
66
Vie w in g a st ill p ict u re – Me m o ry p h o t o p la yb a ck
Note
When displaying the index screen, the number appears above each image. This
indicates the order in which images are recorded in the built-in flash memory. These
numbers are different from the data file names.
Files modified w ith personal computers
These files cannot be displayed on the index screen. Image files shot with other
equipment cannot be displayed on the index screen either.
The image quality mode indicator
The indicator may show a mode different to the one in which you recorded. This is not
a malfunction. The indicator shows the size of the data file.
67
Vie w in g a st ill p ict u re – Me m o ry p h o t o p la yb a ck
Vie w in g t h e re co rd e d im a g e s u sin g a p e rso n a l co m p u t e r
You can view the still pictures which are recorded in the built-in flash memory on the
PC screen.
Set the POWER switch to VTR, or set the POWER switch to CAMERA and set
STANDBY to MEMORY. Connect your camcorder to your PC using the PC serial cable
supplied with your camcorder. The PC MODE indicator appears in the viewfinder or
on the LCD screen.
For details on the connection and operation refer to the operating instruction supplied
with PictureGear 3.2Lite (supplied with your camcorder).
Serial port
DIGITAL
I/ O
: Signal flow
PC serial cable (supplied)
To fin ish PC m o d e
Remove the PC serial cable from the DIGITAL I/ O jack
Examples of recommended OS/application softw are
OS
• Windows95 or 98
• WindowsNT4.0
Application
• Microsoft Internet Explorer, etc.
Notes
• When you view images recorded with the camcorder on a personal computer, the
display may show lines on the edge of the screen, depending on the current state of
video input signals. This is not a malfunction.
• You cannot access your PC:
– while the tape is being played back.
– during the slide show.
– while copying still images.
– while the cassette compartment is opened.
68
Pla yin g b a ck im a g e s in a co n t in u o u s lo o p
– SLIDE SHOW
You can automatically play back images in sequence. This function is useful especially
when checking the recorded images or during a presentation.
(1) Set the POWER switch to CAMERA.
(2) Turn STANDBY to MEMORY.
(3) Press MENU to display the MENU settings.
(4) Turn the SEL/ PUSH EXEC dial to select
, then press the dial.
(5) Turn the SEL/ PUSH EXEC dial to select SLIDE SHOW, then press the dial.
(6) Press MEMORY PLAY. The unit plays back the images recorded in the built-in
flash memory in sequence. When all the images have been played back, the
display shows the first image again and the slide show ends.
POWER
1
CAMERA
OFF
VTR
K
2
START/STOP
MEMORY SET
CONTINUOUS
QUAL I TY
4
5
6
FLD.
/
FRAME
PLAY
PROTECT
SLIDE SHOW
DELETE ALL
FORMAT
[
]
:
MENU END
MEMORY SET
CONTINUOUS
QUAL I TY
SLIDE SHOW STD
DSC00027
1 / 3 3
FLD.
/
FRAME
3
MENU
PROTECT
SLIDE SHOW
DELETE ALL
FORMAT
READY
RETURN
[
]
:
[
] :
[
] :
MENU END
M
PLAY START MENU END
To st o p t h e slid e sh o w
Press MENU.
To p a u se d u rin g a slid e sh o w
Press MEMORY PLAY.
To st a rt t h e slid e sh o w fro m a p a rt icu la r im a g e
Select the desired image using MEMORY +/ – buttons before step 3.
To view the recorded images on TV
Connect your camcorder to a TV with the supplied A/ V connecting cable before
operation.
Note on the slide show
You cannot make a copy of the slide show on a tape.
69
Pre ve n t in g a ccid e n t a l e ra su re – PROTECT
To prevent accidental erasure of important images, you can protect selected images.
(1) Display the image you want to protect.
(2) Press MENU to display the MENU settings.
(3) Turn the SEL/ PUSH EXEC dial to select
, then press the dial.
(4) Turn the SEL/ PUSH EXEC dial to select PROTECT, then press the dial.
(5) Turn the SEL/ PUSH EXEC dial to select ON, then press the dial.
(6) Press MENU to make the MENU disappear. The “H” mark is displayed
beside the data file name of the protected image.
MEMORY SET
CONTINUOUS
QUAL I TY
3
2
FLD.
/
FRAME
MENU
PROTECT
SLIDE SHOW
DELETE ALL
FORMAT
[
]
:
MENU END
MEMORY SET
CONTINUOUS
QUAL I TY
1
/
5
MEMORY SET
CONTINUOUS
QUAL I TY
1
/
5
4
5
FLD.
/
FRAME
FLD.
/
FRAME
PROTECT
PROTECT
ON
OFF
SLIDE SHOW
DELETE ALL
FORMAT
SLIDE SHOW OFF
DELETE ALL
FORMAT
RETURN
RETURN
[
]
:
[
]
:
MENU END
MENU END
MEMORY SET
CONTINUOUS
QUAL I TY
1
/
5
FLD.
/
FRAME
PROTECT
ON
SLIDE SHOW
DELETE ALL
FORMAT
RETURN
[
]
:
MENU END
To ca n ce l im a g e p ro t e ct io n
Select OFF in step 5, then press the SEL/ PUSH EXEC dial.
Note
Formatting erases all information in the built-in flash memory, including the protected
image data. Check the contents of the flash memory before formatting.
70
De le t in g im a g e s – DELETE
De le t in g se le ct e d im a g e s
(1) Display the image you want to delete.
(2) Press MEMORY DELETE. “DELETE?” appears on the LCD screen.
(3) Press MEMORY DELETE again. The selected image is deleted.
DELETE
DSC00010
STD
1 2 / 3 3
DELETE
2,3
DELETE?
[
] :
DELETE DEL
[
] :
– CANCEL
To ca n ce l d e le t in g a n im a g e
Press MEMORY – in step 3.
To d e le t e a n im a g e d isp la ye d o n t h e in d e x scre e n
Press MEMORY +/ – to move the ” indicator to the desired image and follow steps 2
and 3.
Notes
• To delete a protected image, first cancel image protection.
• Once you delete an image, you cannot restore it. Check the images to delete carefully
before deleting them.
71
De le t in g im a g e s – DELETE
Era sin g a ll t h e im a g e s
You can delete all the unprotected images in the built-in flasn memory.
(1) Set the POWER switch to CAMERA.
(2) Set the STANDBY to MEMORY.
(3) Press MENU to display the MENU settings.
(4) Turn the SEL/ PUSH EXEC to select
, then press the dial.
(5) Turn the SEL/ PUSH EXECl dial to select DELETE ALL, then press the dial.
(6) Turn the SEL/ PUSH EXEC dial to select OK, then press the dial. The OK
indicator changes to EXECUTE.
(7) Turn the SEL/ PUSH EXEC dial to select EXECUTE, then press the dial. The
DELETING indicator appears on the LCD screen. When all the unprotected
images are deleted, the COMPLETE indicator is displayed.
POWER
1
CAMERA
OFF
VTR
K
2
START/STOP
MEMORY SET
CONTINUOUS
QUAL I TY
3
4
FLD.
/
FRAME
MENU
PROTECT
SLIDE SHOW
DELETE ALL
FORMAT
[
]
:
MENU END
MEMORY SET
CONTINUOUS
QUAL I TY
MEMORY SET
CONTINUOUS
QUAL I TY
5
6
7
FLD.
/
FRAME
FLD.
/
FRAME
PROTECT
PROTECT
SLIDE SHOW
DELETE ALL READY
FORMAT
SLIDE SHOW
DELETE ALL RETURN
FORMAT
RETURN
OK
RETURN
[
]
:
[
]
:
MENU END
MENU END
MEMORY SET
CONTINUOUS
QUAL I TY
MEMORY SET
CONTINUOUS
QUAL I TY
FLD.
/
FRAME
FLD.
/
FRAME
PROTECT
PROTECT
SLIDE SHOW
SLIDE SHOW
DELETE ALL RETURN
DELETE ALL RETURN
FORMAT
RETURN
OK
FORMAT
RETURN
EXECUTE
[
]
:
[
]
:
MENU END
MENU END
MEMORY SET
CONTINUOUS
QUAL I TY
MEMORY SET
CONTINUOUS
QUAL I TY
FLD.
/
FRAME
FLD.
/
FRAME
PROTECT
SLIDE SHOW
PROTECT
SLIDE SHOW
DELETE ALL DELETING
FORMAT
DELETE ALL COMPLETE
FORMAT
RETURN
RETURN
[
]
:
[
]
:
MENU END
MENU END
72
De le t in g im a g e s – DELETE
To ca n ce l d e le t in g a ll t h e im a g e s in t h e b u ilt -in fla sh m e m o ry
Select
RETURN in step 4, then press the control dial.
While the DELETING indicator appears
Do not turn the POWER switch or press any buttons.
73
Co p yin g im a g e s re co rd e d in t h e b u ilt -in
fla sh m e m o ry t o t a p e s
You can copy still images recorded in the built-in flash memory and record them to a
tape.
Before operation
Insert a tape for recording.
(1) Set the POWER switch to VTR.
(2) Using the tape transport buttons, search a point where you want to record the
desired still image. Set the tape to the playback pause mode.
(3) Press r REC to set the tape to the recording pause mode.
(4) Press PLAY to play back the still image you want to copy.
(5) Press P to start recording and press P again to stop.
(6) If you have more to copy, repeat steps 4 and 5.
2
3
REC
4
POWER
1
PLAY
CAMERA
OFF
5
PAUSE
VTR
To st o p co p yin g m id w a y
Press p.
During copying
You cannot operate the following buttons:
MEMORY PLAY, MEMORY INDEX, MEMORY DELETE, MEMORY +, and
MEMORY –.
74
Co p yin g t h e im a g e re co rd e d in t h e b u ilt -in fla sh m e m o ry t o t a p e s
Note on the index screen
You cannot record the index screen.
If you press the EDITSEARCH buttons in the pause mode
Memory playback stops.
If you press the DISPLAY button in the standby or recording modes
You can view memory playback and the file name indicators in addition to the
indicators associated with tapes, such as the time code indicator.
75
— Cu st o m izin g Yo u r Ca m co rd e r —
Ch a n g in g t h e MENU se t t in g s
To change the mode settings in the MENU settings, select the menu items with the
SEL/ PUSH EXEC dial. The factory settings can be partially changed. First, select the
icon, then the menu item and then the mode.
(1) In the standby, MEMORY or VTR mode, press MENU.
(2) Turn the SEL/ PUSH EXEC dial to select the desired icon, then press the dial to
set.
(3) Turn the SEL/ PUSH EXEC dial to select the desired item, then press the dial to
set.
(4) Turn the SEL/ PUSH EXEC dial to select the desired mode, and press the dial
to set.
(5) If you want to change other items, select
RETURN and press the dial, then
repeat steps from 2 to 4.
CAMERA SET
D
ZOOM
1
2
3
4
CAMERA
VTR
16 : 9WIDE
OTHERS
WORLD TIME
BEEP
COMMANDER
DISPLAY
REC LAMP
INDICATOR
CAMERA SET
ZOOM
16 : 9WIDE
STEADYSHOT
N. S. LIGHT
VTR SET
MENU
D
H i F i SOUND
AUDIO MIX
PB MODE
[MENU] : END
[MENU] : END
OTHERS
WORLD TIME
BEEP
COMMANDER
DISPLAY
REC LAMP
INDICATOR
0
HR
OTHERS
WORLD TIME
BEEP
0
HR
OTHERS
WORLD TIME
BEEP
COMMANDER ON
DISPLAY
REC LAMP
INDICATOR
RETURN
OTHERS
WORLD TIME
BEEP
COMMANDER ON
DISPLAY
OFF
REC LAMP
INDICATOR
OTHERS
WORLD TIME
BEEP
COMMANDER ON
DISPLAY
REC LAMP
INDICATOR
RETURN
OFF
OTHERS
WORLD TIME
BEEP
COMMANDER OFF
DISPLAY
REC LAMP
INDICATOR
RETURN
To m a ke t h e MENU d isp la y d isa p p e a r
Press MENU.
76
Ch a n g in g t h e MENU se t t in g s
Note
When you let the subject monitor the shot (Mirror mode), the menu display does not
appear.
Menu items are displayed as the follow ing seven icons:
CAMERA SET
VTR SET
LCD/ VF SET
MEMORY SET
TAPE SET
SETUP MENU
OTHERS
Se le ct in g t h e m o d e se t t in g o f e a ch it e m
r is the factory setting.
Menu items differ according to whether the POWER switch is set to VTR or CAMERA.
POWER
Icon/item
D ZOOM
Mode
Meaning
sw itch
ON
To activate digital zoom. More than 20× to 360×
zoom is performed digitally (p. 17)
CAMERA
r OFF
r OFF
ON
To prevent the deterioration of the picture quality
—
16:9WIDE
CAMERA*
To record a 16:9 wide picture (p. 29)
To compensate for camera-shake
STEADYSHOT r ON
CAMERA
OFF
To cancel the SteadyShot function. Natural
pictures are produced when shooting a stationary
object with a tripod.
N.S. LIGHT
r ON
To use the NightShot Light function (p. 20)
To cancel the NightShot Light function
CAMERA
OFF
* This item is displayed only when the STANDBY switch is set to STANDBY.
Notes on the SteadyShot function
• The SteadyShot function will not correct excessive camera-shake.
• Attachment of a conversion lens (not supplied) may influence the SteadyShot
function.
• SteadyShot does not operate in the 16:9WIDE mode. If you set STEADYSHOT to ON
in the MENU settings, the
indicator flashes.
77
Ch a n g in g t h e MENU se t t in g s
POWER
sw itch
Icon/item
HiFi SOUND
Mode
Meaning
r STEREO
To play back a stereo tape or dual sound track
tape with main and sub sound
VTR
1
2
To play back dual sound track tape with main
sound
To play back a dual sound track tape with sub
sound
AUDIO MIX
PB MODE
To adjust the balance between the stereo 1 and
stereo 2
VTR
VTR
ST1
ST2
r AUTO
To automatically select the system (Hi8/
standard 8 or Digital8) that was used to record
on the tape, and play back the tape
H/ h
To play back a tape that was recorded in the
Hi8/ standard 8 system when your camcorder
does not automatically distinguish the
recording system
VTR
LCD B. L.
r BRT NORMAL To set the brightness on the LCD screen normal
CAMERA
BRIGHT
To brighten the LCD screen
VTR
CAMERA
LCD COLOR
To adjust the color on the LCD screen, turn and
press the SEL/ PUSH EXEC dial
To lighten
To darken
VF B. L.
r BRT NORMAL To set the brightness in the viewfinder normal
BRIGHT To bright the viewfinder
VTR
CAMERA
Notes on AUDIO MIX
• You can adjust the balance only for tapes recorded in the Digital8 system.
• When playing back a tape recorded in the 16-bit mode, you cannot adjust the balance .
Note on PB MODE
The mode will return to the factory setting when:
• you remove the battery pack or power source.
• you turn the POWER switch.
Notes on LCD B. L. and VF B. L.
• When you select “BRIGHT”, battery life is reduced by about 10 percent during
recording.
• When you use power sources other than the battery pack, “BRIGHT” is automatically
selected.
78
Ch a n g in g t h e MENU se t t in g s
POWER
sw itch
Icon/item
Mode
Meaning
CONTINUOUS r OFF
Not to store continuously
To record 3 or 4 pictures continuously
CAMERA*
ON
MULTI SCRN To record 9 pictures continuously
QUALITY
r STANDARD
To record still pictures in the standard image
VTR
quality mode
CAMERA*
FINE
To store still pictures in the fine image quality
mode
FLD./FRAME
PROTECT
r FIELD
FRAME
r OFF
ON
To record moving subjects
CAMERA*
To record stopping subjects in high quality
Not to protect still pictures
VTR
CAMERA*
To protect selected still pictures against
accidental erasure. (p. 70)
CAMERA*
SLIDE SHOW
DELETE ALL
FORMAT
To play back images in a continuous loop.
(p. 69)
To delete all the images (p. 72)
To format the built-in flash memory
To duplicate still pictures (p. 63)
VTR
CAMERA*
VTR
CAMERA*
PHOTO SAVE
VTR
* These items are displayed only when the STANDBY switch is set to MEMORY.
Notes on FORMAT
Format (initialize) the built-in flash memory when the warning indicator
fast.
flashes
To format (initialize) the built-in flash memory, carry out the following operation.
(1) Set the POWER switch to CAMERA or VTR. When you set the POWER switch
to CAMERA, turn STANDBY to MEMORY.
(2) Press MENU to display the MENU settings.
(3) Turn the SEL/ PUSH EXEC dial to select
, then press the dial.
(4) Turn the SEL/ PUSH EXEC dial to select FORMAT, then press the dial.
(5) Turn the SEL/ PUSH EXEC dial to select OK, then press the dial.
To cancel formatting, select RETURN, then press the dial.
• Formatting erases all information in the built-in flash memory, including the protected
image data. Check the contents of the flash memory before formatting.
• Be sure that the battery pack is fully charged when formatting the built-in flash
memory.
Formatting takes about three seconds.
• Do not turn the POWER switch or press any button while the display shows
“FORMATTING”.
79
Ch a n g in g t h e MENU se t t in g s
POWER
sw itch
Icon/item
Mode
Meaning
AUDIO MODE r 12BIT
To record or play back in the 12-bit mode (two
stereo sounds)
VTR*
CAMERA**
16BIT
To record or play back in the 16-bit mode (the
one stereo sound with high quality)
Ò REMAIN
r AUTO
To display the remaining tape bar:
• for about 8 seconds after your camcorder is
turned on and calculates the remaining
amount of tape
VTR
CAMERA**
• for about 8 seconds after a cassette is inserted
and your camcorder calculates the remaining
amount of tape
• for about 8 seconds after ( is pressed in
VTR mode
• for about 8 seconds after DISPLAY is pressed
to display the screen indicators
• for the period of tape rewinding, forwarding
or picture search in the VTR mode
ON
To always display the remaining tape indicator
VTR
DATA CODE
r DATE/ CAM
To display date, time and recording data
during playback
DATE
To display date and time during playback
CLOCK SET
To reset the date or time (p. 82)
—
CAMERA
AUTO TV ON
r OFF
VTR
CAMERA
ON
To automatically turn on the Sony TV when
using the laser link function
VTR
CAMERA
TV INPUT
r VIDEO1
VIDEO2
VIDEO3
To switch the video input on a Sony TV when
using the laser link function (p. 26)
OFF
—
VTR
LTR SIZE
r NORMAL
2×
To display selected menu items in normal size
CAMERA
To display selected menu items at twice the
normal size
CAMERA
DEMO MODE
r ON
To make the demonstration appear
To cancel the demonstration mode
OFF
*
To dub a tape to another VCR
You cannot select AUDIO MODE for tapes recorded in the Digital8 system. You,
however, can select AUDIO MODE when you dub tapes recorded in the Hi8/
standard 8 system to another VCR using the i.LINK cable.
** These items are displayed only when the STANDBY switch is set to STANDBY.
Note on AUDIO MODE
When playing back a tape recorded in the 16-bit mode, you cannot adjust the balance in
AUDIO MIX.
Notes on DEMO MODE
• You cannot select DEMO MODE when a cassette is inserted in your camcorder.
• DEMO MODE is set to STBY (Standby) at the factory and the demonstration starts
about 10 minutes after you have set the POWER switch to CAMERA without a
cassette inserted.
Note that you cannot select STBY of DEMO MODE in the MENU settings.
• When NIGHTSHOT is set to ON, the NIGHTSHOT indicator appears in the
viewfinder or on the LCD screen and you cannot select DEMO MODE in the MENU
settings.
80
Ch a n g in g t h e MENU se t t in g s
POWER
sw itch
Icon/item
WORLD TIME
Mode
Meaning
To set the clock to the local time. Turn the SEL/
PUSH EXEC dial to set a time difference. The
clock changes by the time difference you set
here. If you set the time difference to 0, the
clock returns to the originally set time.
CAMERA
BEEP
r MELODY
To output the melody when you start/ stop
recording or when an unusual condition occurs
on your camcorder
VTR
CAMERA
NORMAL
OFF
To output the beep instead of the melody
To cancel the melody and beep sound
COMMANDER r ON
To activate the Remote Commander supplied
with your camcorder
VTR
CAMERA
OFF
To deactivate the Remote Commander to avoid
remote control misoperation caused by other
VCR’s remote control
DISPLAY
r LCD
V-OUT/ LCD
To show the display on the LCD screen and
viewfinder
VTR
CAMERA
To show the display on the TV screen, LCD
screen and viewfinder
REC LAMP
INDICATOR
r ON
To light up the camera recording lamp at the
front of your camcorder
CAMERA
OFF
To turn the camera recording lamp off so that
the subject is not aware of the recording
VTR
CAMERA
r BL OFF
To turn off the backlight on display window
To turn on the backlight
BL ON
In more than 5 minutes after removing the pow er source
The “COMMANDER” and “HiFi SOUND” items are returned to their factory settings.
The other menu items are held in memory even when the battery is removed, as long as
the lithium battery is installed.
Note
If you press DISPLAY with “DISPLAY” set to “V-OUT/ LCD” in the MENU settings,
the picture from a TV or VCR will not appear on the LCD screen even when your
camcorder is connected to outputs on the TV or VCR.
Notes on INDICATOR
• When you select “BL ON”, battery life is reduced by about 10 percent during
recording.
• When you use power sources other than the battery pack, “BL ON” is automatically
selected.
81
Re se t t in g t h e d a t e a n d t im e
The clock is set to East Coast Standard Time at the factory.
The date and time are held in memory by the lithium battery. If you replace the lithium
battery with the battery pack or other power source connected, you need not reset the
date and time.
You must reset the date and time when the lithium battery becomes dead with no
power source installed.
First, set the year, then the month, the day, the hour and then the minute.
(1) While the camcorder is in the standby mode, press MENU to display the
MENU settings.
(2) Turn the SEL/ PUSH EXEC dial to select , then press the dial.
(3) Turn the SEL/ PUSH EXEC dial to select CLOCK SET, then press the dial.
(4) Turn the SEL/ PUSH EXEC dial to adjust the desired year, then press the dial.
(5) Set the month, day and hour by turning the SEL/ PUSH EXEC dial and
pressing the dial.
(6) Set the minute by turning the SEL/ PUSH EXEC dial and pressing the dial by
the time signal. The clock starts to move.
(7) Press MENU to make the MENU settings disappear.
1,
7
2
3
MENU
SETUP MENU
SETUP MENU
CLOCK SET
AUTO TV ON
TV INPUT
LTR SIZE
DEMO MODE
RETURN
SETUP MENU
CLOCK SET
AUTO TV ON
TV INPUT
LTR SIZE
JAN
1
1998
CLOCK SET
AUTO TV ON
TV INPUT
LTR SIZE
DEMO MODE
RETURN
12:00:00AM
1998 JAN
1
DEMO MODE
12 00 AM
[MENU] : END
[MENU] : END
6
4
SETUP MENU
SETUP MENU
CLOCK SET
AUTO TV ON
TV INPUT
LTR SIZE
CLOCK SET
AUTO TV ON
TV INPUT
LTR SIZE
JUL
4
1999
5:30:00PM
1999 JUL
4
DEMO MODE
RETURN
DEMO MODE
RETURN
5
30 PM
1999 JAN
1
1999 JAN
1
[MENU] : END
[MENU] : END
12 00 AM
12 00 AM
The year changes as follow s:
1998 1999 N · · · · n 2029
˜
Note on the time indicator
The internal clock of your camcorder operates on a 12-hour cycle.
• 12:00 AM stands for midnight.
• 12:00 PM stands for noon.
82
— Ad d it io n a l In fo rm a t io n —
Dig it a l8
p la yb a ck
syst e m , re co rd in g a n d
Wh a t is t h e “ Dig it a l8
syst e m ” ?
This video system has been developed to enable digital recording to Hi8 video cassette
H.
Usa b le ca sse t t e t a p e s
We recommend using Hi8 video cassettes H. The recording time when you use your
Digital8 system camcorder on Hi8 H/ standard 8 h tape is half the recording time
when using the conventional Hi8 H/ standard 8 h system camcorder. (120 minutes
of recording time becomes 60 minutes.)
If you use standard 8 h tape, be sure to play back the tape on this camcorder. Mosaic
pattern noise may appear when you play back standard 8 h tape on other VCRs.
Note
Tapes recorded in the Digital8 system cannot be played back on Hi8 H/ standard 8
h system machine.
Pla yb a ck syst e m
The Digital8 system or Hi8 H/ standard 8 h system is automatically detected
before the tape is played back.*
* During playback of tapes recorded in the Hi8 H/ standard 8 h system, digital
signals are output as the image signals from the DV IN/ OUT jack.
Display during automatic detection of system
The Digital8 system or Hi8 H/ standard 8 h system is automatically detected, and
the playback system is automatically switched to. During switching of systems, the
screen turns blue, and the following displays appear. A hissing noise also sometimes
can be heard.
n H/ h: During switching from Digital8 to Hi8 H/ standard 8 h
H/ h n : During switching from Hi8 H/ standard 8 h to Digital8
Wh e n yo u p la y b a ck
Playing back a PAL-recorded tape
You can play back tapes recorded in the PAL video system on the LCD screen, if the
tape is recorded in the Digital8 system.
Co p yrig h t sig n a l
Wh e n yo u re co rd
You cannot record softw are on your camcorder that contains copyright control
signals for copyright protection of softw are.
“COPY INHIBIT” appears on the LCD screen, in the viewfinder or on the TV screen if
you try to record such software.
Your camcorder does not record copyright control signals on the tape when it records.
83
Dig it a l8 syst e m , re co rd in g a n d p la yb a ck
Wh e n yo u p la yb a ck a d u a l so u n d t ra ck t a p e
Wh e n yo u u se t a p e s re co rd e d in t h e Dig it a l8
syst e m
When you playback a Digital8 system tape which is dubbed from a dual sound track
tape recorded in the DV system, set “HiFi SOUND” to the desired mode in the MENU
settings (p. 76).
Sound from speaker
HiFi Sound
Mode
Playing back
a stereo tape
Playing back a dual
sound track tape
STEREO
Stereo
Lch
Main sound and sub sound
Main sound
1
2
Rch
Sub sound
Wh e n yo u u se t a p e s re co rd e d in t h e Hi8/st a n d a rd 8 syst e m
When you play back a dual sound track tape recorded in an AFM HiFi stereo system,
set “HiFi SOUND” to the desired mode in the MENU settings (p. 76).
Sound from speaker
HiFi Sound
Mode
Playing back
a stereo tape
Playing back a dual
sound track tape
STEREO
Stereo
Main sound and sub sound
Main sound
1
2
Monaural
Unnatural sound
Sub sound
You cannot record dual sound programs on your camcorder.
84
Ch a n g in g t h e lit h iu m b a t t e ry in yo u r
ca m co rd e r
When replacing the lithium battery, keep the battery pack or other power source
attached. Otherwise, you will need to reset the date, time and other items in the MENU
settings hold in memory by the lithium battery.
Insert the battery with the positive (+) side facing out. When the battery becomes weak
or dead, the I indicator flashes in the viewfinder for about 5 seconds when you set the
POWER switch to CAMERA. In this case, replace the battery w ith a Sony CR2025 or
Duracell DL-2025 lithium battery. Use of any other battery may present a risk of
fire or explosion. Discard used batteries according to the manufacturer’s instructions.
(+)
(---)
WARNING
The battery may explode if mistrested. Do not recharge, disassemble, nor dispose of it
in fire.
Lithium battery
• Keep the lithium battery out of the reach of children.
• Should the battery be swallowed, immediately consult a doctor.
• Wipe the battery with a dry cloth to ensure good contact.
Lithium battery installed at the factory
This battery may not last 1 year.
85
Ch a n g in g t h e lit h iu m b a t t e ry in yo u r ca m co rd e r
Ch a n g in g t h e lit h iu m b a t t e ry
(1) Open the LCD panel and open the lid of the lithium battery compartment.
(2) Push the lithium battery down once and pull it out from the holder.
(3) Install a Sony CR2025 or Duracell DL-2025 lithium battery with the positive (+)
side facing out.
(4) Close the lid.
1
2
4
1
3
25
0
2
R
C
86
Tro u b le sh o o t in g
If you run into any problem using your camcorder, use the following table to
troubleshoot the problem. If the problem persists, disconnect the power source and
contact your Sony dealer or local authorized Sony service facility. If “C:ππ:ππ”
appears on the LCD screen or in the viewfinder, the self-diagnosis display function has
worked. See page 91.
In t h e re co rd in g m o d e
Symptom
Cause and/or Corrective Actions
START/ STOP does not operate.
• The POWER switch is set to VTR.
m Set it to CAMERA. (p. 13)
• STANDBY is set to LOCK.
m Turn STANDBY to STANDBY. (p. 13)
• The tape has run out.
m Rewind the tape or insert a new one. (p. 12, 22)
• The write-protect tab is set to expose the red mark.
m Use a new tape or slide the tab. (p. 12)
• The tape is stuck to the drum (moisture condensation).
m Remove the cassette and leave your camcorder for at
least 1 hour to acclimatize. (p. 94)
Recording stops in a few seconds.
The power goes off.
• START/ STOP MODE is set to 5SEC or
m Set it to . (p. 18)
• While being operated in the CAMERA mode, your
camcorder has been in the standby mode for more than 3
minutes.
.
m Turn STANDBY down once and then up again. (p. 13)
Your camcorder turns on/ off when
using the accessory that is attached
to the intelligent accessory shoe.
• Your camcorder is working with the AC power adaptor.
m Use the battery pack.
The image on the viewfinder screen
is not clear.
• The viewfinder lens is not adjusted.
m Adjust the viewfinder lens. (p. 16)
The SteadyShot function does not
work.
• STEADYSHOT is set to OFF in the MENU settings.
m Set it to ON. (p. 76)
• The SteadyShot function does not work when the wide
mode is set to ON.
The autofocusing function does not
work.
• FOCUS is set to MANUAL.
m Set it to AUTO. (p. 40)
• Shooting conditions are not suitable for autofocus.
m Set FOCUS to MANUAL to focus manually. (p. 40)
The fader function does not work.
• START/ STOP MODE is set to 5SEC or
m Set it to . (p. 18)
.
• The digital effect function is working.
m Cancel it. (p. 35)
The v indicator flashes in the
• The video heads may be dirty.
viewfinder.
m Clean the heads using the Sony V8-25CLD cleaning
cassette (not supplied). (p. 95)
The picture does not appear in the
viewfinder.
• The LCD panel is open.
m Close the LCD panel. (p. 14)
(Continued on the following page)
87
Tro u b le sh o o t in g
Symptom
Cause and/or Corrective Actions
• The contrast between the subject and background is too
high. Your camcorder is not a malfunction.
A vertical band appears when you
shoot a subject such as lights or a
candle flame against a dark
background.
A vertical band appears when you
shoot a very bright subject.
• Your camcorder is not a malfunction.
• Slow shutter, low lux or NightShot +Slow shutter mode is
activated. This is not a malfunction.
Some tiny white spots appear in the
viewfinder or on the LCD screen.
• If 10 minutes elapse after you set the POWER switch to
CAMERA or DEMO MODE is set to ON in the MENU
settings without a cassette inserted, your camcorder
automatically starts the demonstration.
An unknown picture is displayed in
the viewfinder or on the LCD screen.
m Insert a cassette and the demonstration stops.
You can also cancel DEMO MODE. (p. 80)
• NIGHTSHOT is set to ON.
m Set it to OFF. (p. 19)
The picture is recorded in incorrect
or unnatural colors.
Picture appears too bright, and the
subject does not appear in the
viewfinder or on the LCD screen.
• NIGHTSHOT is set to ON in a bright place.
m Set it to OFF, or use the NightShot function in a dark
place. (p. 19)
In t h e p la yb a ck m o d e
Symptom
Cause and/or Corrective Actions
The tape does not move when a
video control button is pressed.
• The POWER switch is set to CAMERA or OFF.
m Set it to VTR. (p. 22)
• The tape has run out.
m Rewind the tape. (p. 22)
The playback picture is not clear or
does not appear.
• The television’s video channel is not adjusted correctly.
m Adjust it. (p. 25)
There are four horizontal lines on the • The video head may be dirty.
picture or the playback picture is not
m Clean the heads using the Sony V8-25CLD cleaning
cassette (not supplied). (p. 95)
clear or does not appear.
No sound or only a low sound is
heard when playing back a tape.
• The stereo tape is played back with HiFi SOUND set to 2
in the MENU settings.
m Set it to STEREO. (p. 76)
• The volume is turned to minimum.
m Open the LCD panel and press VOLUME +. (p. 22)
• AUDIO MIX is set to ST2 side in the MENU settings.
m Adjust AUDIO MIX. (p. 76)
The date search does not work
correctly.
• The tape has a blank portion in the recorded portion
(p. 46)
The picture which is recorded in the
Digital8 system is not played back.
• PB MODE is set to H/ h in the MENU settings.
m Set it to AUTO. (p. 76)
The tape which is recorded in the
Hi8/ standard 8 system is not played
back correctly.
• Set PB MODE to H/ h in the MENU settings. (p. 76)
88
Tro u b le sh o o t in g
In t h e re co rd in g a n d p la yb a ck m o d e s
Symptom
Cause and/or Corrective Actions
The power does not turn on.
• The battery pack is not installed, or is dead or nearly dead.
m Install a charged battery pack. (p. 8, 9)
• The AC power adaptor is not connected to a wall outlet.
m Connect the AC power adaptor to a wall outlet. (p. 11)
• The tape was ejected after recording.
The end search function does not
work.
• You have not recorded on the new cassette yet.
The battery pack is quickly
discharged.
• The operating temperature is too low.
• The battery pack is not fully charged.
m Charge the battery pack again. (p. 9)
• The battery pack is completely dead, and cannot be
recharged.
m Replace with a new battery pack. (p. 8)
The battery remaining
indicator does not indicate
the correct time.
• You have used the battery pack in an extremely hot or
cold environment for a long time.
• The battery pack is completely dead, and cannot be
recharged.
m Replace with a new battery pack. (p. 8)
• The battery is dead.
m Use a charged battery pack. (p. 8, 9)
The cassette cannot be removed from • The power source is disconnected.
the holder.
m Connect it firmly. (p. 8, 11)
• The battery is dead.
m Use a charged battery pack or the AC power adaptor.
(p. 8, 9)
The { and 6 indicators flash and no • Moisture condensation has occurred.
functions except for cassette ejection
work.
m Remove the cassette and leave your camcorder for at
least 1 hour to acclimatize. (p. 94)
In t h e fla sh m e m o ry fu n ct io n
Symptom
Cause and/or Corrective Actions
Recording does not function.
• The STANDBY switch is not set to MEMORY.
m Set it to MEMORY. (p. 58)
• The built-in flash memory has already been recorded to its
full capacity.
m Erase unnecessary images and record again. (p. 70)
The image cannot be deleted.
• The image is protected.
m Cancel image protection. (p. 70)
(Continued on the following page)
89
Tro u b le sh o o t in g
Ot h e rs
Symptom
Cause and/or Corrective Actions
The Remote Commander supplied
with your camcorder does not work.
• COMMANDER is set to OFF in the MENU settings.
m Set it to ON. (p. 76)
• Something is blocking the infrared rays.
m Remove the obstacle.
• The batteries are inserted in the battery holder with the + –
polarities incorrectly matching the + – marks.
m Insert the batteries with the correct polarity. (p. 104)
• The batteries are dead.
m Insert new ones. (p. 104)
The picture from a TV or VCR does
not appear even when your
camcorder is connected to outputs on
the TV or VCR.
• DISPLAY is set to V-OUT/ LCD in the MENU settings.
m Set it to LCD. (p. 76)
The melody or beep sounds for 5
seconds.
• Moisture condensation has occurred.
m Remove the cassette and leave your camcorder for at
least 1 hour to acclimatize. (p. 94)
• Some troubles has occurred in your camcorder.
m Remove the cassette and insert it again, then operate
your camcorder.
While charging the battery pack, no
indicator appears or the indicator
flashes in the display window.
• The AC power adaptor is disconnected.
m Connect it firmly. (p. 9)
• Something is wrong with the battery pack.
m Contact your Sony dealer or local authorized Sony
service facility.
90
Se lf-d ia g n o sis d isp la y
Your camcorder has a self-diagnosis display
function.
Vie w fin d e r (o r LCD scre e n )
This function displays the current condition of
your camcorder as a 5-digit code (a combination of
a letter and figures) in the viewfinder, on the LCD
screen or in the display window. If a 5-digit code is
displayed, check the following code chart. The last
two digits (indicated by ππ) will differ depending
on the state of your camcorder.
C:21:00
Self-diagnosis display
• C:ππ:ππ
You can service your camcorder
yourself.
• E:ππ:ππ
Contact your Sony dealer or local
authorized Sony facility.
Five-digit display
Cause and/or Corrective Actions
• You are using a battery pack that is not an
C:04:ππ
“InfoLITHIUM” battery pack.
m Use an “InfoLITHIUM” battery pack. (p. 11)
C:21:ππ
• Moisture condensation has occurred.
m Remove the cassette and leave your camcorder for at
least 1 hour to acclimatize. (p. 94)
C:22:ππ
• The video heads are dirty.
m Clean the heads using the Sony V8-25CLD cleaning
cassette (not supplied). (p. 95)
C:31:ππ
• A malfunction other than the above that you can service
has occurred.
m Remove the cassette and insert it again, then operate
your camcorder.
C:32:ππ
m Disconnect the power cord of the AC power adaptor or
remove the battery pack. After reconnecting the power
source, operate your camcorder.
E:61:ππ
• A malfunction that you cannot service has occurred.
m Contact your Sony dealer or local authorized Sony
service facility and inform them of the 5-digit code.
(example: E:61:10)
E:62:ππ
If you are unable to rectify the problem even if you try corrective actions a few times,
contact your Sony dealer or local authorized Sony service facility.
91
Wa rn in g in d ica t o rs a n d m e ssa g e s
If indicators and messages appear in the viewfinder, on the LCD screen or in the
display window, check the following:
See the page in parentheses “( )” for more information.
• The warning messages do not appear in the mirror mode.
• The indicators and messages are displayed in yellow.
Wa rn in g in d ica t o rs
The image date is protected.
The video heads are dirty
Fast flashing:
Self-diagnosis display (p. 91)
• You need to clean the
heads using the Sony V8-
25CLD cleaning cassette
(not supplied) (p. 95).
Moisture condensation has occurred*
Fast flashing:
• Eject the cassette, turn off your
camcorder, and leave it for about 1 hour
with the cassette compartment open
(p. 94).
The battery is dead or
nearly dead
Slow flashing:
C:21:00
• The battery is nearly dead.
Fast flashing:
• The battery is dead (p. 9).
You cannot use the built-in flash
memory*
Slow flashing:
Warning indicator as to
tape
Slow flashing:
• The tape is near the end.
• No tape is inserted (p. 12).*
• The write-protect tab on the
cassette is out (red) (p. 12)*
• The built-in flash memory is full.
Fast flashing:
• You cannot use the built-in flash
memory. Format it (p. 79).
Fast flashing:
• The tape has run out (p. 12, 22).*
You need to eject the cassette
Slow flashing:
• The write-protect tab on the cassette is
out (red) (p. 12).*
The lithium battery is w eak
or is not installed (p. 85)
Fast flashing:
• Moisture condensation has occurred
(p. 94).
• The tape has run out (p. 12, 22).*
• The self-diagnosis display function is
activated (p. 91).
Wa rn in g m e ssa g e s
CLEANING
CASSETTE
The video heads are dirty.
COPY
INHIBIT
You tried to record a picture that has a copyright control signal (p. 83).
* You hear the melody or beep sound.
92
Usin g yo u r ca m co rd e r a b ro a d
Usin g yo u r ca m co rd e r a b ro a d
You can use your camcorder in any country or area with the AC power adaptor
supplied with your camcorder within 100 V to 240 V AC, 50/ 60 Hz.
When charging the battery pack, use a commercially available AC plug adaptor [a ], if
necessary, depending on the design of the wall outlet [b ].
AC-L10A/L10B/L10C
[a ]
[b ]
Your camcorder is an NTSC system based camcorder. If you want to view the playback
picture on a TV, it must be an NTSC system based TV with VIDEO/ AUDIO input jack.
The following shows TV color systems used overseas.
NTSC system
Bahama Islands, Bolivia, Canada, Central America, Chile, Colombia, Ecuador, Jamaica,
Japan, Korea, Mexico, Peru, Surinam, Taiwan, the Philippines, the U.S.A., Venezuela,
etc.
PAL system
Australia, Austria, Belgium, China, Czech Republic, Denmark, Finland, Germany, Great
Britain, Holland, Hong Kong, Italy, Kuwait, Malaysia, New Zealand, Norway, Portugal,
Singapore, Slovak Republic, Spain, Sweden, Switzerland, Thailand, etc.
PAL-M system
Brazil
PAL-N system
Argentina, Paraguay, Uruguay
SECAM system
Bulgaria, France, Guyana, Hungary, Iran, Iraq, Monaco, Poland, Russia, Ukraine, etc.
Sim p le se t t in g o f clo ck b y t im e d iffe re n ce
You can easily set the clock to the local time by setting a time difference. Select WORLD
TIME in the MENU settings. See page 76 for more information.
93
Ma in t e n a n ce in fo rm a t io n a n d
p re ca u t io n s
Mo ist u re co n d e n sa t io n
If your camcorder is brought directly from a cold place to a warm place, moisture may
condense inside your camcorder, on the surface of the tape, or on the lens. In this
condition, the tape may stick to the head drum and be damaged or your camcorder may
not operate correctly. If there is moisture inside your camcorder, the beep sounds and
the { indicator flashes. When the 6 indicator flashes at the same time, the cassette is
inserted in your camcorder. If moisture condenses on the lens, the indicator will not
appear.
If m o ist u re co n d e n sa t io n o ccu rre d
None of the functions except cassette ejection will work. Eject the cassette, turn off your
camcorder, and leave it for about 1 hour with the cassette compartment open. Your
camcorder can be used again if the { indicator does not appear when the power is
turned on again.
Note on moisture condensation
Moisture may condense when you bring your camcorder from a cold place into a warm
place (or vice versa) or when you use your camcorder in a hot place as follows:
• You bring your camcorder from a ski slope into a place warmed up by a heating
device
• You bring your camcorder from an air-conditioned car or room into a hot place
outside
• You use your camcorder after a squall or a shower
• You use your camcorder in a high temperature and humidity place
How to prevent moisture condensation
When you bring your camcorder from a cold place into a warm place, put your
camcorder in a plastic bag and tightly seal it. Remove the bag when the air temperature
inside the plastic bag has reached the surrounding temperature (after about 1 hour).
94
Ma in t e n a n ce in fo rm a t io n a n d p re ca u t io n s
Ma in t e n a n ce in fo rm a t io n
Cle a n in g t h e vid e o h e a d
To ensure normal recording and clear pictures, clean the video heads. The video head
may be dirty when:
• mosaic-pattern noise appears on the playback picture.
• playback pictures do not move.
• playback pictures are hardly visible.
• playback pictures do not appear.
• the v indicator and “ CLEANING CASSETTE” message appear one after another
or the v indicator flashes on the LCD screen or in the viewfinder.
[a ]
[b ]
or
/
If above problem, [a ] or [b ] occurs, clean the video heads with the Sony V8-25CLD
cleaning cassette (not supplied). Check the picture and if the above problem persists,
repeat cleaning.
Cle a n in g t h e LCD scre e n
If fingerprints or dust make the LCD screen dirty, we recommend using a LCD
Cleaning Kit (not supplied) to clean the LCD screen.
95
Ma in t e n a n ce in fo rm a t io n a n d p re ca u t io n s
Pre ca u t io n s
Ca m co rd e r o p e ra t io n
• Operate your camcorder on 7.2 V (battery pack) or 8.4 V (AC power adaptor).
• For DC or AC operation, use the accessories recommended in this operating
instructions.
• If any solid object or liquid get inside the casing, unplug your camcorder and have it
checked by a Sony dealer before operating it any further.
• Avoid rough handling or mechanical shock. Be particularly careful of the lens.
• Keep the POWER switch set to OFF when you are not using your camcorder.
• Do not wrap your camcorder with a towel, for example, and operate it. Doing so
might cause heat to build up inside.
• Keep your camcorder away from strong magnetic fields or mechanical vibration.
• Do not touch the LCD screen with your fingers or a sharp-pointed object.
• If your camcorder is used in a cold place, a residual image may appear on the LCD
screen. This is not a malfunction.
• While using your camcorder, the back of the LCD screen may heat up. This is not a
malfunction.
On h a n d lin g t a p e s
Do not insert anything into the small holes on the rear of the cassette. These holes are
used to sense the type and thickness of the tape and if the recording tab is in or out.
Ca m co rd e r ca re
• Remove the tape, and periodically turn on the power, operate the CAMERA and VTR
sections and play back a tape for about 3 minutes when your camcorder is not to be
used for a long time.
• Clean the lens with a soft brush to remove dust. If there are fingerprints on the lens,
remove them with a soft cloth.
• Clean the camcorder body with a dry soft cloth, or a soft cloth lightly moistened with
a mild detergent solution. Do not use any type of solvent which may damage the
finish.
• Do not let sand get into your camcorder. When you use your camcorder on a sandy
beach or in a dusty place, protect it from the sand or dust. Sand or dust may cause
your camcorder to malfunction, and sometimes this malfunction cannot be repaired.
Co n n e ct io n t o yo u r PC
• When recording with i.LINK cable the image processed or edited by your PC, use a
new Hi8 H tape. (for models which have the DV IN jack only)
• When inputting the image recorded by Hi8/ standard 8 (analog) system into your PC,
dub the image into a Digital8 or DV tape first, and then input it into your PC.
When inputting the image recorded by Hi8/standard 8 system into SONY VAIO
The Program Capture function of DVgate motion doesn’t work. To use this function,
dub the image into a Digital8 or DV tape first, and then input it into your SONY
VAIO.
96
Ma in t e n a n ce in fo rm a t io n a n d p re ca u t io n s
AC p o w e r a d a p t o r
• Unplug the unit from the wall outlet when you are not using the unit for a long time.
To disconnect the power cord, pull it out by the plug. Never pull the power cord itself.
• Do not operate the unit with a damaged cord or if the unit has been dropped or
damaged.
• Do not bend the power cord forcibly, or place a heavy object on it. This will damage
the cord and may cause fire or electrical shock.
• Prevent metallic objects from coming into contact with the metal parts of the
connecting section. If this happens, a short may occur and the unit may be damaged.
• Always keep metal contacts clean.
• Do not disassemble the unit.
• Do not apply mechanical shock or drop the unit.
• While the unit is in use, particularly during charging, keep it away from AM receivers
and video equipment. AM receivers and video equipment disturb AM reception and
video operation.
• The unit becomes warm during use. This is not a malfunction.
• Do not place the unit in locations that are:
– Extremely hot or cold
– Dusty or dirty
– Very humid
– Vibrating
No t e s o n d ry b a t t e rie s
To avoid possible damage from battery leakage or corrosion, observe the following:
• Be sure to insert the batteries with the + – polarities matched to the + – marks.
• Dry batteries are not rechargeable.
• Do not use a combination of new and old batteries.
• Do not use different types of batteries.
• Current flows from batteries when you are not using them for a long time.
• Do not use leaking batteries.
If batteries are leaking
• Wipe off the liquid in the battery compartment carefully before replacing the batteries.
• If you touch the liquid, wash it off with water.
• If the liquid get into your eyes, wash your eyes with a lot of water and then consult a
doctor.
If any problem occurs, unplug your camcorder and contact your nearest Sony dealer.
97
Sp e cifica t io n s
Operating temperature
32 °F to 104 °F (0 °C to 40 °C)
Storage temperature
–4 °F to +140 °F (–20 °C to +60 °C)
Dimensions (Approx.)
4 3/ 8 × 4 5/ 8 × 8 1/ 8 in.
(108 × 117 × 206 mm) (w/ h/ d)
Mass (approx.)
In p u t a n d o u t p u t
co n n e ct o rs
Vid e o ca m e ra
re co rd e r
S video input/output
4-pin mini DIN
Syst e m
Luminance signal: 1 Vp-p,
75 ohms, unbalanced
Chrominance signal: 0.286 Vp-p,
75 ohms, unbalanced
Video input/output
Video recording system
2 rotary heads
Helical scanning system
Audio recording system
Rotary heads, PCM system
Quantization: 12 bits (Fs 32 kHz,
stereo 1, stereo 2), 16 bits
(Fs 48 kHz, stereo)
2 lb 3 oz (1 kg)
excluding the battery pack, lithium
battery, cassette and shoulder
strap
Phono jack, 1 Vp-p, 75 ohms,
unbalanced
Audio input/output
Phono jacks (2: stereo L and R)
327 mV, (at output impedance
47 kilohms) impedance less than
2.2 kilohms
RFU DC OUT
Special minilack, DC 5V
DV input/output
4-pin connector
Headphone jack
Stereo minijack (ø 3.5 mm)
LANC control jack
Stereo mini-minijack (ø 2.5 mm)
MIC jack
2 lb 6 oz (1.1 kg)
including the battery pack
NP-F330, lithium battery CR2025,
120 min. cassette and shoulder
strap
Supplied accessories
See page 7.
Video signal
NTSC color, EIA standards
Recommended cassette
Hi8 video cassette
Recording/playback time (using
120 min. cassette)
1 hour
Fastforw ard/rew ind time (using
120 min. cassette)
Approx. 8 min.
Image device
1/ 4 inch CCD (Charge Coupled
Device)
Approx. 460,000 pixels
(Effective: Approx. 290,000 pixels)
Lens
AC p o w e r a d a p t o r
Pow er requirements
100 - 240 V AC, 50/ 60 Hz
Pow er consumption
23 W
Output voltage
DC OUT: 8.4 V, 1.5 A in operating
mode
Minijack, 0.388 mV low impedance
with 2.5 to 3.0 V DC, output
impedance 6.8 kilohms (ø 3.5 mm)
Stereo type
Combined power zoom lens
Filter diameter 1 7/ 16 in. (37 mm)
20× (Optical), 360×(Digital)
Focal length
5/ 32 - 2 7/ 8 in. (3.6 - 72 mm)
When converted to a 35 mm still
camera
1 5/ 8 - 32 3/ 8 in. (41 - 820 mm)
Color temperature
Auto
Minimum illumination
1 lux (F 1.4)
0 lux (in the NightShot mode)*
* Objects unable to be seen due to
the dark can be shot with
infrared lighting.
Built-in flash memory
2 MB
JPEG compression
Operating temperature
32 °F to 104 °F (0 °C to 40 °C)
Storage temperature
–4 °F to +140 °F (–20 °C to +60 °C)
Dimensions (approx.)
5 × 1 9/ 16 × 2 1/ 2 in.
(125 × 39 × 62 mm) (w/ h/ d)
excluding projecting parts
Mass (approx.)
DIGITAL I/O
Minijack (ø 3.5 mm) Stereo type
Transfer rate: Max. 115.2 Kbps
LCD scre e n
Picture
4 inches measured diagonally
3 1/ 4 × 2 3/ 8 in. (80.7 × 58.9 mm)
Total dot number
9.8 oz (280 g)
112,086 (479 × 234)
excluding power cord
Cord length (approx.)
AC power cord: 6.6 feet (2 m)
Connecting cord: 5.2 feet (1.6 m)
Ge n e ra l
Pow er requirements
7.2 V (battery pack)
8.4 V (AC power adaptor)
Average pow er consumption
(w hen using the battery pack)
During camera recording using
LCD
Design and specifications are
subject to change without notice.
4.6 W
Viewfinder
3.3 W
98
— Qu ick Re fe re n ce —
Id e n t ifyin g t h e p a rt s a n d co n t ro ls
Ca m co rd e r
5
6
7
8
9
1
2
0
!¡
3
4
!™
!£
1 POWER sw itch (p. 13)
2 LCD BRIGHT buttons (p. 14)
3 OPEN button (p. 13)
4 VOLUME buttons (p. 22)
5 Eyecup
8 PHOTO button (p. 27)
9 BATT RELEASE lever (p. 8)
0 STANDBY sw itch (p. 13)
!¡ START/STOP button (p. 13)
!™ Hooks for shoulder strap (p. 102)
!£ DC IN jack (p. 9)
6 View finder lens adjustment lever
(p. 16)
7 Pow er zoom lever (p. 17)
This mark indicates that this product is a genuine accessory for Sony
video products.
When purchasing Sony video products, Sony recommends that you
purchase accessories with this “GENUINE VIDEO ACCESSORIES”
mark.
99
Id e n t ifyin g t h e p a rt s a n d co n t ro ls
!¢
!∞
@£
@¢
!§
!¶
@∞
@§
!•
!ª
@º
@¡
@™
@¶
!¢ Video control buttons
(p. 22, 24, 51, 53, 74)
@º Microphone
@¡ FOCUS sw itch (p. 40)
p STOP (stop)
0 REW (rewind)
@™ PUSH AUTO button (p. 40)
@£ +SLOW SHUTTER button (p. 20)
@¢ NIGHTSHOT sw itch (p. 19)
@∞ Display w indow (p. 105)
@§ Remote sensor (p. 104)
@¶ Tripod receptacle (base)
( PLAY (playback)
) FF (fastforward)
P PAUSE (pause)
r REC (recording)
The control buttons light up when you
set the POWER switch to VTR.
!∞ EDITSEARCH buttons (p. 21)
!§ LASER LINK button (p. 26)
!¶ Focus ring (p. 40)
Make sure that the length of the tripod
screw is less than 9/ 32 inch (6.5 mm).
Otherwise, you cannot attach the tripod
securely and the screw may damage
your camcorder.
!• Camera recording lamp (p. 13)
!ª Infrared rays emitter (p. 19, 26)
What is LASER LINK?
The LASER LINK system sends and receives pictures and sound between video
equipment having the mark by using infrared rays.
100
Id e n t ifyin g t h e p a rt s a n d co n t ro ls
@•
@ª
#º
#£
#¢
#∞
#§
#¡
#™
#¶
#•
@• START/STOP MODE sw itch (p. 18)
@ª Intelligent accessory shoe
#º Speaker
#¢ BACK LIGHT button (p. 19)
#∞ PROGRAM AE button (p. 38)
#§ EXPOSURE button (p. 39)
#¶ SEL/PUSH EXEC dial (p. 33)
#• MENU button (p. 29, 55, 76)
#¡ LCD screen (p. 14)
#™ Lithium battery compartment (p. 86)
#£ FADER button (p. 31)
Notes on the intelligent accessory shoe
• The intelligent accessory shoe supplies power to optional accessories such as a video
light or microphone.
• The intelligent accessory shoe is linked to STANDBY, allowing you to turn the power
supplied by the shoe on and off. Refer to the operating instructions of the accessory
for further information.
• The intelligent accessory shoe has a safety device for fixing the installed accessory
securely. To connect an accessory, press down and push it to the end, and then tighten
the screw.
• To remove an accessory, loosen the screw, and then press down and pull out the
accessory.
101
Id e n t ifyin g t h e p a rt s a n d co n t ro ls
$∞
$§
#ª
$º
$¡
$™
$¶
$•
$£
$¢
$ª
%º
#ª DATA CODE button (p. 23)
$º DISPLAY button (p. 23)
$∞ END SERCH button (p. 21)
$§ © (self timer) button (p. 15)
$¶ PICTURE EFFECT button (p. 33, 42)
$• DIGITAL I/O jack (p. 68)
$¡ DIGITAL EFFECT button (p. 35, 43)
$™ MEMORY PLAY button (p. 65)
$£ MEMORY INDEX button (p. 66)
$¢ MEMORY – button (p. 65)
$ª MEMORY DELETE button (p. 71)
%º MEMORY + button (p. 65)
Attaching the shoulder strap
Attach the shoulder strap supplied with your camcorder to the hooks for the shoulder
strap.
102
Id e n t ifyin g t h e p a rt s a n d co n t ro ls
%§
%¡
%™
%£
%¢
%∞
%¶
%•
%ª
^º
^¡
%¡ View finder (p. 16)
%• RFU DC OUT (RFU adaptor DC output)
jack (p. 25)
%™ EJECT sw itch (p. 12)
%ª MIC jack (PLUG IN POWER)
Connect an external microphone
(not supplied). This jack also accepts
a “plug-in-power” microphone.
If you connect a 2-pin microphone,
supply power from DC OUT jack.
%£ LANC l control jack
LANC stands for Local Application
Control Bus System. The l control jack
is used for controlling the tape transport
of video equipment and other
peripherals connected to the video
equipment. This jack has the same
function as the jack indicated as
CONTROL L or REMOTE.
^º DV IN/OUT jack (p. 50, 62)
This “i.LINK” mark is a trademark of
Sony Corporation and indicates that this
product is in agreement with IEEE 1394-
1995 specifications and their revisions.
%¢ Cassette compartment (p. 12)
%∞ Grip strap
The DV IN/ OUT jack is i.LINK
compatible.
%§ S VIDEO jack (p. 25, 28, 49, 51, 62)
%¶ 2 (headphones) jack
^¡ VIDEO/AUDIO jacks
When you use headphones, the speaker
on your camcorder is silent.
(p. 25, 28, 49, 51, 62)
Fastening the grip strap
Fasten the grip strap firmly.
103
Id e n t ifyin g t h e p a rt s a n d co n t ro ls
Re m o t e Co m m a n d e r
The buttons that have the same name on the Remote Commander as on your camcorder
function identically to the buttons on your camcorder.
7
1
2
3
4
5
8
9
0
6
1 PHOTO button (p. 27)
7 ZERO SET MEMORY button
(p. 41, 44, 53)
2 DISPLAY button (p. 23)
8 Transmitter
3 SEARCH MODE button (p. 45, 47, 48)
4 =/+ buttons (p. 45, 47, 48)
5 Tape transport buttons (p. 24)
6 DATA CODE button (p. 23)
Point toward the remote sensor to
control the camcorder after turning on
the camcorder.
9 START/STOP button (p. 13)
!º Pow er zoom button (p. 17)
To p re p a re t h e Re m o t e Co m m a n d e r
Insert 2 size AA (R6) batteries by matching the + and – polarities on the batteries to
the + – marks inside the battery compartment.
Notes on the Remote Commander
• Point the remote sensor away from strong light sources such as direct sunlight or
overhead lighting. Otherwise, the Remote Commander may not function properly.
• Your camcorder works in the commander mode VTR 2. Commander modes
1, 2 and 3 are used to distinguish your camcorder from other Sony VCRs to avoid
remote control misoperation. If you use another Sony VCR in the Commander mode
VTR 2, we recommend changing the commander mode or covering the sensor of the
VCR with black paper.
104
Id e n t ifyin g t h e p a rt s a n d co n t ro ls
Op e ra t io n in d ica t o rs
Vie w fin d e r
Disp la y w in d o w
!£
1
2
3
4
5
6
7
@∞
@¡
@¶
3
!¢
SP
0:00:00
STBY
40min
1
@§
!∞
!§
W
T
M.FADER
16:9WIDE
SEPIA
ZERO SET
MEMORY
DATE 01
SEARCH
!¶
!•
!ª
DV IN
16BIT
f
8
9
0
!¡
!™
ac
@º
@¡
@™
@£
@¢
!¢ Tape counter (p. 18, 41, 44, 53) /Time
1 Tape speed mode indicator
This indicator appears while playing
back in the Hi8/ standard 8 system.
/Mirror mode indicator (p. 14)
code indicator (p. 18)/Self-diagnosis
display function indicator (p. 91)/5SEC
mode indicator (p. 18)/Photo
recording indicator (p. 27)/Image
number indicator (p. 58)
2 Format indicator (p. 18, 83)
, H or h indicator appears.
3 Remaining battery time indicator
!∞ Remaining tape indicator (p. 18)/
Memory playback indicator (p. 66)
(p. 18)
!§ ZERO SET MEMORY indicator
(p. 41, 44, 53)
4 Exposure indicator (p. 39)/Zoom
indicator (p. 17)/Data file name
indicator (p. 54)
!¶ Search mode indicator (p. 45, 47, 48)
!• NIGHTSHOT indicator (p. 19)
!ª DV IN indicator (p. 49)
5 Fader indicator (p. 31)/Digital effect
indicator (p. 35, 43)/FRAME indicator
(p. 57)
@º Audio mode indicator (p. 80)
@¡ Warning indicators (p. 92)
@™ Continuous mode indicator (p. 60)
@£ Video flash ready indicator
This indicator appears when you use the
video flash light (not supplied).
6 Wide mode indicator (p. 29)
7 Picture effect indicator (p. 33, 42)
8 LCD bright indicator (p. 14)/Volume
indicator (p. 22)/Data code indicator
(p. 23)
@¢ Self-timer indicator (p. 15)
@∞ Hi8 indicator
9 PROGRAM AE indicator (p. 38)
0 Backlight indicator (p. 19)
This indicator appears while playing
back in the Hi8 system.
@§ Tape counter (p. 18, 41, 44, 53)/Time
code indicator (p. 18)Self-diagnosis
display function indicator (p. 91)/
Remaining battery time indicator
(p. 9)
!¡ SteadyShot off indicator (p. 77)
!™ Manual focusing indicator (p. 40)
!£ Standby/Recording indicator (p. 13)/
Video control mode (p. 24)/Image
quality mode indicator (p. 55)
@¶ FULL charge indicator (p. 9)
105
Qu ick Fu n ct io n Gu id e
Fu n ct io n s t o a d ju st e xp o su re (in t h e re co rd in g m o d e )
• In a dark place
NIGHTSHOT (p. 19)
• In insufficient light
Low lux mode (p. 37)
• In dark environments such as sunset, fireworks,
or general night views
Sunset & moon mode (p. 37)
• Shooting backlit subjects
• In spotlight, such as at the theater or a formal
event
BACK LIGHT (p. 19)
Spotlight mode (p. 37)
• In strong light or reflected light, such as
at a beach in midsummer or on a ski slope
Beach & ski mode (p. 37)
Fu n ct io n s t o g ive im a g e s m o re im p a ct
(in t h e re co rd in g m o d e )
• Smooth transition between scenes
• Taking a still picture
FADER (p. 31)
PHOTO (p. 27)
• Digital processing of images
• Processing a scene using digital effects
• Creating a soft background for subjects
PICTURE EFFECT (p. 33)
DIGITAL EFFECT (p. 35)
Soft portrait mode (p. 37)
Fu n ct io n s t o g ive a n a t u ra l a p p e a ra n ce t o yo u r re co rd in g s
(in t h e re co rd in g m o d e )
• Preventing deterioration of picture quality
in digital zoom
D ZOOM [MENU] (p. 76)
• Focusing manually
Manual focus (p. 40)
• Shooting distant subjects
• Recording fast-moving subjects
Landscape mode (p. 37)
Sports lesson mode (p. 37)
Fu n ct io n s t o u se in e d it in g (in t h e re co rd in g m o d e )
• Watching the picture on a wide-screen TV
Wide mode (p. 29)
Fu n ct io n s t o u se a ft e r re co rd in g (in t h e p la yb a ck m o d e )
• Digital processing of recorded images
• Processing a recorded scene using digital effect
• Displaying the date/ time or recording data
when you recorded
PICTURE EFFECT (p. 42)
DIGITAL EFFECT (p. 43)
Data code (p. 23)
• Quickly locating a desired scene
• Searching for scenes recorded in the
photo mode
Zero set memory (p. 41, 44, 53)
Photo seach (p. 47)
• Scanning scenes recorded in the Photo mode
• Playing back on monaural sound or sub sound
• Playing back the picture on a TV without
connecting a cord
Photo scan (p. 48)
HiFi SOUND [MENU] (p. 76)
LASER LINK (p. 26)
Fu n ct io n s u sin g t h e b u ilt -in fla sh m e m o ry
• Connecting to your PC
• Recording still pictures at high quality
PC mode (p. 68)
FRAME (p. 57)
106
In d e x
A, B
I, J, K, L
R
Adjusting viewfinder ............. 16
AC power adaptor .................... 9
AFM HiFi Sound .................... 84
ANTI GROUND SHOOTING
................................................ 18
A/ V connecting cable
.............................. 25, 28, 49, 51
BACK LIGHT .......................... 19
Battery pack ............................... 8
Beep .......................................... 81
BOUNCE .................................. 30
i.LINK ............................... 50, 103
Index screen ............................. 66
“InfoLITHIUM” battery ........ 11
Infrared rays emitter ........ 19, 26
JPEG .......................................... 54
LANC ..................................... 103
LASER LINK ........................... 26
LCD screen .............................. 14
LUMINANCEKEY ................. 34
Rec review ............................... 21
Recording and playback
systems .................................. 83
Recording mode ..................... 57
Recording time ........................ 10
Remaining tape indicator ...... 18
Remaining battery time
indicator ................................ 18
Remote control jack (LANC)
.............................................. 103
Remote commander ............. 104
Remote sensor ....................... 104
M, N
Main sound .............................. 84
Manual focus ........................... 40
Menu settings .......................... 76
Mirror mode ............................ 14
Moisture condensation .......... 94
Monaural.................................. 25
MONOTONE .......................... 30
Mosaic fader ............................ 30
NIGHTSHOT .......................... 19
Normal charge .......................... 9
NTSC system ........................... 93
C, D
S
Charging battery ....................... 9
Clock set ................................... 82
Connection
S video jack ............ 25, 28, 49, 50
SEL/ PUSH EXEC dial ......... 101
Shoulder strap ....................... 102
Skip scan .................................. 24
Slow playback ......................... 24
SLIDE SHOW .......................... 69
+SLOW SHUTTER ................. 20
START/ STOP MODE ............ 18
STEADYSHOT ........................ 77
Stereo tape ............................... 84
STILL ........................................ 34
Sub sound ................................ 78
SLOW SHUTTER .................... 34
(viewing on TV) ................... 25
(dubbing a tape) .................. 49
Connection to your PC .......... 96
CONTINUOUS ....................... 59
Data code ................................. 23
Date search .............................. 45
DELETE .................................... 71
DEMO ...................................... 80
DIGITAL EFFECT ............ 35, 43
Digital 8 system ...................... 83
DISPLAY .................................. 23
Dual sound track tape ............ 84
DV connecting cable ......... 50, 62
O, P, Q
OLD MOVIE ............................ 34
Operation indicators ............ 105
OVERLAP ................................ 30
PC MODE ................................ 68
Photo scan ................................ 48
Photo search ............................ 47
Photo recording ...................... 27
PICTURE EFFECT ............ 33, 42
Picture search .......................... 24
Playback pause ........................ 24
Power sources
T, U, V
Time code ................................. 18
Tape counter .......... 18, 41, 44, 53
Telephoto ................................. 17
TRAIL ....................................... 34
Transition ................................. 13
TV color systems ..................... 93
E
EDITSEARCH ......................... 21
END SEARCH ................... 21, 24
Exposure .................................. 39
External microphone (not
supplied) ............................. 103
(house current) ..................... 11
(car battery) .......................... 11
(battery pack) ......................... 8
Power zoom ............................. 17
PROGRAM AE ....................... 37
PROTECT................................ 70
QUALITY ................................. 55
W, X, Y, Z
F, G, H
Wide-angle .............................. 17
Wide mode .............................. 29
WORLD TIME ......................... 81
Write-protect tab ..................... 12
Zoom ........................................ 17
Zero set memory ......... 41, 44, 53
FADER ..................................... 30
Fade in/ out .............................. 30
FIELD/ FRAME ....................... 57
FLASH MOTION .................... 34
FOCUS...................................... 40
FORMAT .................................. 79
Full charge ................................. 9
Grip strap ............................... 103
Heads ........................................ 95
Headphone jack .................... 103
HiFi SOUND ........................... 78
107
Sony Corporation Printed in Japan
|