PAL
Camera Control Unit
CCU-TX7P
MAIN FEATURES
transfer high quality digital signals with
just one cable to SDI ready units. Using
the SDI interface, a total digital DXC
system becomes a reality.
Hig h Q u a lity Tria x
Tw o In p u ts fo r Re tu rn Vid e o
The CCU-TX7P has two RETURN
VIDEO inputs (BNC type) and therefore
accept return video signals (VBS colour)
from two different systems. Two
channels of return video can be selected
from the Sony CA-TX7P Camera
Adaptor.
Tra n sm issio n
The CCU-TX7P also employs analogue
component video transmission, with a
9MHz bandwidth for the luminance (Y)
signal and 4.5MHz for the colour
difference signals (R-Y/B-Y) . This
assures high quality and the provision of
various video outputs from the CCU.
Note* The CCU-TX7P (Serial No. less than 41000)
needs some modification to accommodate the
SDI outputs. Please contact your nearest
Sony office.
O th e r Sig n a l O u tp u ts
The CCU-TX7P provides two composite
outputs, and two component output
selectable from Y/R-Y/B-Y, R/G/B and
Y/C. The CCU-TX7 also has a 4-pin
WF MODE (waveform monitor mode)
connector for flickerless parade
monitoring of signals, in addition to a
WF output and a PIX (picture monitor)
output.
Co lo u r Te le p ro m p te r Fa cility
The CCU-TX7P can be used with colour
teleprompter facilities. Since reverse
signal transmission (CA -> CCU) is
supported using a teleprompter video
channel in a triax cable, it is also
possible to transmit video signals other
than those for teleprompter from CA to
CCU, if necessary.
Lo n g Dista n ce Tra n sm issio n
Cable length can be extended up to a
maximum of 1500m via ø14.5mm triax
cable (with return video) (Fujikura),
1125m via ø13.2mm cable (Belden) or
750m via ø8.5mm cable (Fujikura,
Belden). Teleprompter video channel
can also be transmitted over a limited
length of cable.
* For detailed information, please contact your
nearest Sony office.
Hig h Sp e e d Hig h Q u a lity Se ria l
Da ta Tra n sm issio n
Data at up to a resolution of 10-bits can
be transmitted with high speed via serial
data transmission using a triax cable.
This provides the benefits of smooth,
real-time control with instant tactile
response from remote control devices.
AC/ DC O p e ra tio n
The CCU-TX7P is designed to operate
on not only AC but also DC power with
both an AC inlet and, for DC 12V (10.5V
to 17V), a DC inlet. DC operation
greatly expands system flexibility in
outside broadcast applications.
Dig ita l Sig n a l O u tp u ts
The CCU-TX7P provides two SDI
outputs when the optional DXBK-701
SDI Output Board is installed. It can
3
MAIN FEATURES
Fle x ib le In te rco m Sy ste m
Pro g ra m m e Micro p h o n e Syste m
The CCU-TX7P and CA-TX7P are
Co a x ia l Co n tro l Ca p a b ility
The CCU-TX7P is equipped with a
coaxial input. This enables each camera
to operate over conventional coaxial
cable instead of a triax cable, with power
supplied locally to the camera.
The CCU-TX7P is equipped with a
programme audio channel and a
equipped with a two-channel microphone
system. Two XLR connectors on the
CA-TX7P provide balanced audio CH-1
and CH-2 inputs with microphone
bi-directional intercom channel.
Programme audio sound from an
external audio system can be fed to the
camera head. This can be mixed with
intercom sound; major intercom systems
(Four-wire/Two-wire/RTS/Clearcom) can
be interfaced via connectors on the rear
panel of the CCU-TX7P. The camera
control unit accepts two-channel input
from the external intercom system, and
communication can be initiated from the
CCU-TX7P, or the camera adaptor
(CA-TX7P) or the external intercom
system (CH-1 or CH-2).
phantom power available for an external
microphone. The MIC input gain of each
channel can be controlled within a range
of ±12dB in 16 steps by control volumes
on the internal board of the CCU-TX7P.
* For detailed information, please contact your
nearest Sony office.
Co m p a ct Size
The CCU-TX7P is half a 19-inch rack
size wide and 4 units (4U) high. With the
Sony RMM-TXC7 Rack Mount Kit, two
CCU-TX7P units or one unit with a
waveform monitor can be mounted into a
standard 19-inch rack.
RS-2 3 2 C Po rt
The CCU-TX7P is equipped with an
RS-232C port to link several CCU-TX7P
units for a multiple camera control
system, or to connect an external
personal computer.
DXBK-701 SDI Output Board
4
PERIPHERALS
CA-TX7 P
Ro ta ry Tria x Co n n e cto r
Vie w fin d e r Bo x Cu rso r
In d ica tio n
The Sony CA-TX7P Triax Camera
Adaptor is equipped with a rotary (70˚)
triax connector for easy cabling.
The CA-TX7P can indicate a box cursor
on the screen of any DXC-D30P/
D30WSP viewfinder such as the
DXF-701WSCE and DXF-51. Cursor
position (H, V) and size (width, height)
can all be adjusted using control volumes
on the rear panel of the
7 6 -p in / 5 0 -p in In te rfa ce
The CA-TX7P is equipped with both
Pro 76-pin and Pro 50-pin interfaces,
which facilitate connections to DXC-D30P/
D30WSP and DXC-637P Video Cameras.
CA-TX7P. Two kinds of cursors can be
stored and retrieved.
* This function is not available with the DXC-637P.
Pro 50-pin
Pro 76-pin Digital
5
RCP-TX7
As Re m o te Co n tro l Pa n e l
● Full Camera Control
● Links in Control of Iris and Master
Black
The Sony RCP-TX7 provides full control
functions as a remote camera control
panel for the CCU-TX7P. It covers the
complete range of control functions, from
basic camera control to more
In a multi-camera system, the control of
Iris and Master Black can be linked over
multiple RCP-TX7 panels. Simply press
the “IRIS/M.BLACK LINK” button on each
required RCP-TX7. When controlling Iris
and Master Black, the values of all the
linked RCP-TX7 units can be overridden
by one RCP-TX7. Any one of the units
can be set up as the master device.
● Colour Matching Capability
sophisticated operation. It provides
camera set-up control using convenient
scene files, as well as basic control and
paint operation control. For engineering
and service personnel, the RCP-TX7also
provides comprehensive camera set-up
functions. The RCP-TX7 is a quarter the
width of a 19-inch rack so that four
RCP-TX7 units can be installed into a
standard 19-inch rack using the Sony
RMM-TXR7 Rack Mount Kit.
The RCP-TX7 has a useful colour
matching function. When using multiple
cameras and RCP-TX7 units, once one
RCP-TX7 has been set up, the master
data can be copied to the other RCP-
TX7 units. To do this, the user must first
set one RCP-TX7 as the master and the
others as subsidiary units.
● Scene File System
The RCP-TX7 can store up to 16 scene
files. All parameters, both for camera
operation and set-up, can be adjusted
and stored in each scene file. The stored
scene file most suitable for each shooting
situation can be instantly recalled.
6
PERIPHERALS
CO U-TX7
As Sta n d a lo n e Ca m e ra
Co n tro lle r
Ba sic Ca m e ra Co n tro l w ith
CO U-TX7
Directly connected to the Sony
DXC-D30P/ D30WSP Video Camera
through a 10-pin remote connector, the
RCP-TX7 can be used as a standalone
remote control unit offering the same
functionality as the RM-M7G.
(This is only possible
The Sony COU-TX7 Camera Operation
Unit can be attached to form a part of the
front panel of the CCU-TX7P to provide
basic control of camera operation and
painting. This is useful when using the
CCU-TX7P in limited space, such as in
field production vehicles.
● Convenient Liquid Crystal Display
The RCP-TX7 has an LCD (Liquid
Crystal Display) on the control panel.
This LCD shows menu status information
on the current adjustment. Function
status such as Detail Level, Gamma,
Knee, White Balance and Black (Flare)
Balance can also be displayed on the
LCD by using an INDICATION button.
The LCD also displays troubleshooting
hints when an operational difficulty arises
from use of the RCP-TX7 controls.
with the
DXC-D30P/
D30WSP.)
SYSTEM CO N FIGURATIO N
DXF-51(5-inch)
Monochrome Viewfinder
Intercom
(System & Headset)
WRR-810A + DC-WL800(DC Pack Unit)
Wireless Microphone Receiver
DXC-D30P/
D30WSP or
SDI Output
DXF-701WSCE(*) or
DXC-637P
DXF-601CE
Viewfinder
(w/DXBK-701)
CCU-TX7P
Camera Control Unit
Camera Head
Waveform
Monitor Vectorscope
CA-TX7P
Camera Adaptor
Triax Cable
Picture Monitor
Zoom Lens
AC
CCA-7
(10-pin/10-pin)
(Max.50m)
DC 12V
(*) DXF-701WSCE can be
used only with DXC-D30P/D30WSP.
COU-TX7
Camera Operation
Unit
Intercom
(Headset)
Either the COU-TX7 or the
RCP-TX7 is used as a
control panel of the CCU-TX7P.
RCP-TX7
Remote Control Panel
7
SPECIFICATIO N S
1 . CCU-TX7 P
Input connectors
2 . CA-TX7 P
Input/output connectors
GEN LOCK:
BNC type, loopthrough,
VBS/BS, 1.0Vp-p, 75ohms
BNC type, loopthrough,
VBS, 1.0 Vp-p, 75ohms
BNC type, loopthrough,
VBS, 1.0 Vp-p, 75ohms
XLR 3-pin x 1
BNC type, VBS, 1.0 Vp-p, 75ohms
BNC type,
Y: 1.0Vp-p, 75ohms
R-Y/B-Y: 525mVp-p, 75ohms
BNC type,
700mVp-p, 75ohms
BNC type,
Y: 1.0Vp-p, 75ohms
C: 300mVp-p, 75ohms
Conform to serial digital interfase
(270Mbs), 0.8 Vp-p, 75Ω
CCU:
Triax (Fischer type) x 1
Pro 76P Digital or
Pro 50P switchable
XLR 3-pin x 2, 600ohms, balanced
MIC IN (CH-1/2)
Input level : Mic in: -60dB
: Line in: -20dB
XLR 4-pin x 1,10.5V to 17V
4-pin x 1, 10.5V to 17V, Max 12W
BNC type x 1, 1.0Vp-p, 75ohms
BNC type x 1, 1.0Vp-p, 75ohms
RETURN (1,2):
PROMPT (prompter):
CAMERA INTERFACE:
PGM IN:
VBS (1,2):
(*1)Y/R-Y/B-Y (1,2):
DC IN:
DC OUT:
PROMPTER OUT:
RETURN OUT:
INTERCOM/PROGRAMME: XLR 5-pin x 1 (for Headset)
Input level: -60dBs (dynamic)
Output connectors
(*1)R/G/B (1,2):
(*1)Y/C (1,2):
Output level: ∞ to 12dBs
10-pin x 1
DC 0 to 5V (analogue) x 4
DC 0 or 5V (digital) x 2
DATA OUT:
(*2)SDI (1,2):
Power requirements
Power consumption
DC 120V (from Triax connector) or
DC 12V (10.5 to 17.0V) (from DC IN connector)
SYNC:
BNC type,
VBS, 0.3 Vp-p, 75ohms, negative
BNC type,
1.0 Vp-p, 75ohms
DC 120V
(Supplied from triax connector)
DC 12V
(Supplied from DC IN connector)
PIX (picture monitor):
CA-TX7P
internal only
Total
CA-TX7P
internal only
Total
WF (waveform monitor):
BNC type,
700 mVp-p, 75ohms
(Encoded output: 1.0 Vp-p, 75ohms)
4-pin x 1
XLR 3-pin x 2,
0dBu/-20dBu balanced, 2 channels
CA-TX7P only
10.5W
10.5W
26W
7.5W
7.5W
w/DXC-D30P,
DXF-701CE
11.2W
7.5W
22.3W
WF MODE:
MIC OUT (CH-1/2):
w/DXC-D30P,
DXF-51
12.3W
35W
7.5W
30.2W
Camera control
input/output
connectors
CAMERA:
COAX:
REMOTE:
INTERCOM/TALLY:
Triax (Fischer type) x 1
BNC type x 1
10-pin
D-sub 25-pin x 1
4W/2W
Operating temperature
Storage temperature
Operating humidity
Weight
-10˚C to 45˚C (14˚F to 113˚F)
-20˚C to 55˚C (-4˚F to 131˚F)
20% to 90%
Approx. 2.7 kg (5 lb 15oz)
Dimensions (W x H x D) 226 x 221 x 131mm (9 x 8 3/4 x 5 1/4 inches)
Operation manual x 1
TALLY: 24V DC, TTL level or
contact selectable
Supplied accessory
INTERCOM (Front):
RTS:
RS232C:
AC 220 to 240V or DC 10.5 to 17.0V
95W max.
1500m max. (ø14.5mm)
XLR 5-pin x 1
XLR 3-pin x 1
D-sub 25-pin x 2
27.5
3 . RCP-TX7
Power requirements
10 to 17V (supplied from
camera or CCU)
4.0W
-10˚C to 45˚C (14˚F to 113˚F)
-20˚C to 55˚C (-4˚F to 131˚F)
Approx. 1.5kg (3 lb 5 oz)
Power requirements
Power consumption
Cable length
Power consumption
Operating temperature
Storage temperature
Weight
Dimensions (W x H x D) 100 x 330 x 70mm
(4 x 13 x 2 7/8 inches)
Operating temperature 5˚C to 40˚C (41˚F to 104˚F)
Storage temperature -20˚C to 55˚C (-4˚F to 131˚F)
Weight Approx. 8.45 kg (18 lb 10oz)
Dimensions (W x H x D) 218 x 169 x 415mm (8 5/8 x 6 3/4 x 16 3/8 inches)
Supplied accessories AC power cord x 1
Plug holder for AC power cord x 1
Number plate (1 set)
Cable length
Supplied accessory
50m max. (with CCA-7 cable)
CCA-7-5 Connecting Cable (5m)
Number plate (1set)
Screws and washers x 2
Operation manual x 1
50
70
100
Operation manual x 1
(*)Note: 1) These CCU output signals can be selected to be R/G/B or Y/R-Y/B-Y or Y/C.
2) Using optional DXBK-701 (SDI output board)
1
105 (4
80 (3
/
4
)
22.7
1
/4)
4 . CO U-TX7
Weight
10
Approx. 330g (12.6 oz)
Dimensions (W x H x D) 105 x 155 x 43mm
(4 1/4 x 6 1/8 x 1 3/4 inches)
Operation manual x 1
1
163 (6 /2)
CCU-TX7P
CA-TX7P
Supplied accessory
42.7
49.5
5 . RMM-TXC7
Weight
Approx. 3.7 kg (8 lb 3 oz)
Dimensions (W x H x D) 482 x 177 x 380mm
(19 1/8 x 7 x 15 inches)
Supplied accessories
Installation manual x 1
Blank panel x 1
3
220 (8 /4)
1
/4)
23.3
436 (17
482 (19)
6 . RMM-TXR7
Weight
Dimensions (W x H x D) 482 x 75 x 354mm
(19 x 3 x 14 inches)
Approx. 2.7 kg (5 lb 12 oz)
5
8
30 140 (5 /8)
7
3
200 (7 /8)
9.5 ( /8)
unit: mm (inch)
Supplied accessories
Installation manual x 1
Blank panel x 2
10
29
404 (16)
29
3
424 (16
/4)
60
70
©1999 Sony Corporation. All rights reserved. Reproduction in whole or in part without Sony’s written
permission is prohibited.
482 (19)
7 . DXBK-7 0 1
Power Consumption
Weight
4.5 W
330 g (11.6 oz)
Features and specifications are subject to change without notice.
Sony is a trademark of Sony Corporation.
Dimensions (W x H x D) 17 x 148 x 277 mm
(11/16 x 5 7/8 x 11 inches)
The Quality Management systems in design of the CCU-TX7P, CA-TX7P, RCP-TX7, COU-TX7, RMM-TXC7
and RMM-TXR7 have been assessed and registered as meeting the requirements of ISO 9001.
Distributed by
Printed in Japan
©1999 Sony Corporation
MK4126V2OHB99APR
|
Sterling Plumbing SDRIOM 2 User Manual
Standard Horizon Car Amplifier BMF1000D User Manual
Sony XDP 210EQ User Manual
Sony LCR VX2000A User Manual
Sony Handycam HDR PJ10E User Manual
Sony DSR 450WSPL User Manual
Sony DCR IP5E User Manual
Sony Camera Accessories DCR SC100 User Manual
Samsung VP D361W(i) User Manual
Samsung Car Video System T260 User Manual