Sony BLU RAY DISC BDV E470 User Manual

4-178-243-16(1)  
Blu-ray Disc/DVD  
Home Theatre System  
Operating Instructions  
BDV-E870 / E570 / E470 / E370 / T57 / T37  
©2010 Sony Corporation  
NOTE:  
7) Do not block any ventilation  
openings. Install in accordance  
with the manufacturer’s  
instructions.  
fallen into the apparatus, the  
apparatus has been exposed to  
rain or moisture, does not  
operate normally, or has been  
dropped.  
This equipment has been tested and  
found to comply with the limits for  
a Class B digital device, pursuant to  
Part 15 of the FCC Rules. These  
limits are designed to provide  
reasonable protection against  
harmful interference in a residential  
installation. This equipment  
generates, uses, and can radiate  
radio frequency energy and, if not  
installed and used in accordance  
with the instructions, may cause  
harmful interference to radio  
communications. However, there is  
no guarantee that interference will  
not occur in a particular  
installation. If this equipment does  
cause harmful interference to radio  
or television reception, which can  
be determined by turning the  
equipment off and on, the user is  
encouraged to try to correct the  
interference by one or more of the  
following measures:  
8) Do not install near any heat  
sources such as radiators, heat  
registers, stoves, or other  
apparatus (including  
amplifiers) that produce heat.  
9) Do not defeat the safety  
purpose of the polarized or  
grounding-type plug. A  
For the USB Wireless  
LAN Adapter (UWA-  
BR100) (BDV-E570/  
BDV-T57 only)  
Pursuant to FCC regulations, you  
are cautioned that any changes or  
modifications not expressly  
approved in this manual could void  
your authority to operate this  
equipment.  
polarized plug has two blades  
with one wider than the other. A  
grounding type plug has two  
blades and a third grounding  
prong. The wide blade or the  
third prong are provided for  
your safety. If the provided  
plug does not fit into your  
outlet, consult an electrician for  
replacement of the obsolete  
outlet.  
To prevent radio interference to the  
licensed service, this device is  
intended to be operated indoors and  
away from windows to provide  
maximum shielding. Equipment(or  
its transmit antenna) that is  
installed outdoors is subject to  
licensing.  
10) Protect the power cord from  
being walked on or pinched  
particularly at plugs,  
Only use Wireless LAN indoors  
when using it with IEEE 802.11a  
(5 GHz).  
– Reorient or relocate the receiving  
antenna (aerial).  
convenience receptacles, and  
the point where they exit from  
the apparatus.  
– Increase the separation between  
the equipment and receiver.  
– Connect the equipment into an  
outlet on a circuit different from  
that to which the receiver is  
connected.  
High power radars are allocated as  
primary users (meaning they have  
priority) of 5250-5350 MHz and  
5650-5850 MHz and these radars  
could cause interference and/or  
damage to this device.  
11) Only use attachments/  
accessories specified by the  
manufacturer.  
12) Use only with the cart, stand,  
tripod, bracket, or table  
– Consult the dealer or an  
experienced radio/TV technician  
for help.  
This device uses 5 GHz band for  
wireless LAN communication and  
the maximum gain of the antenna in  
this device is 5 dBi.  
specified by the manufacturer,  
or sold with the apparatus.  
When a cart is used, use caution  
when moving the cart/  
apparatus combination to avoid  
injury from tip-over.  
CAUTION  
This equipment complies with  
FCC/IC radiation exposure limits  
set forth for an uncontrolled  
environment. This equipment  
should be installed and operated  
with minimum distance 20 cm  
between the radiator and your body  
(excluding extremities: hands,  
wrists and feet).  
You are cautioned that any changes  
or modifications not expressly  
approved in this manual could void  
your authority to operate this  
equipment.  
Important Safety  
Instructions  
1) Read these instructions.  
2) Keep these instructions.  
3) Heed all warnings.  
13) Unplug this apparatus during  
lightning storms or when  
This device and its antenna(s) must  
not be co-located or operating with  
any other antenna or transmitter  
except Grant condition.  
unused for long periods of time.  
14) Refer all servicing to qualified  
service personnel. Servicing is  
required when the apparatus  
has been damaged in any way,  
such as power-supply cord or  
plug is damaged, liquid has  
been spilled or objects have  
4) Follow all instructions.  
5) Do not use this apparatus near  
water.  
If you have any questions about this  
product, contact Sony Customer  
Information Service Center at 1-  
6) Clean only with dry cloth.  
US  
3
800-222-7669 or visit http://  
are trademarks of DTS, Inc.  
Product includes software.  
© DTS, Inc. All Rights  
CD, DVD, Blu-ray Disc, and  
music and video-related data from  
Gracenote, Inc., copyright ©  
2000-present Gracenote.  
Reserved.  
The telephone number below is for  
FCC-related matters only.  
• This system incorporates High-  
Definition Multimedia Interface  
(HDMITM) technology.  
HDMI, the HDMI logo and High-  
Definition Multimedia Interface  
are trademarks or registered  
trademarks of HDMI Licensing  
LLC.  
Gracenote Software, copyright ©  
2000-present Gracenote. One or  
more patents owned by Gracenote  
apply to this product and service.  
See the Gracenote website for a  
nonexhaustive list of applicable  
Gracenote patents. Gracenote,  
CDDB, MusicID, MediaVOCS,  
the Gracenote logo and logotype,  
and the “Powered by Gracenote”  
logo are either registered  
Regulatory Information  
Declaration of Conformity  
Trade Name: SONY  
Model: UWA-BR100  
Responsible Party: Sony  
Electronics Inc.  
• Java and all Java-based trademarks  
and logos are trademarks or  
registered trademarks of Sun  
Microsystems, Inc.  
Address: 16530 Via Esprillo,  
San Diego, CA 92127 U.S.A.  
Telephone Number: 858-942-  
2230  
trademarks or trademarks of  
Gracenote in the United States  
and/or other countries.  
• “BD-LIVE” and  
“BONUSVIEW” are trademarks  
of Blu-ray Disc Association.  
• “Blu-ray Disc” is a trademark.  
• “Blu-ray Disc,” “DVD+RW,”  
“DVD-RW,” “DVD+R,” “DVD-  
R,” “DVD VIDEO,” and “CD”  
logos are trademarks.  
This device complies with part  
15 of the FCC rules. Operation is  
subject to the following two  
conditions: (1) This device may  
not cause harmful interference,  
and (2) this device must accept  
any interference received,  
• “PhotoTV HD” and the “PhotoTV  
HD” logo are trademarks of Sony  
Corporation.  
• “Blu-ray 3D” and “Blu-ray 3D”  
logo are trademarks of Blu-ray  
Disc Association.  
including interference that may  
cause undesired operation.  
• MPEG Layer-3 audio coding  
technology and patents licensed  
from Fraunhofer IIS and  
Thomson.  
• “BRAVIA” is a trademark of  
Sony Corporation.  
Copyrights and  
Trademarks  
• “AVCHD” and the “AVCHD”  
logo are trademarks of Matsushita  
Electric Industrial Co., Ltd. and  
Sony Corporation.  
• iPod is a trademark of Apple Inc.,  
registered in the U.S. and other  
countries.  
• This system incorporates with  
Dolby* Digital and Dolby Pro  
Logic (II) adaptive matrix  
surround decoder and the DTS**  
Digital Surround System.  
* Manufacturedunder license  
from Dolby Laboratories.  
Dolby, Pro Logic, and the  
double-D symbol are  
• “Made for iPod” means that an  
electronic accessory has been  
designed to connect specifically  
to iPod and has been certified by  
the developer to meet Apple  
performance standards.  
• “S-AIR” and its logo are  
trademarks of Sony Corporation.  
, “XMB,” and “xross media  
bar” are trademarks of Sony  
Corporation and Sony Computer  
Entertainment Inc.  
• Apple is not responsible for the  
operation of this device or its  
compliance with safety and  
regulatory standards.  
• “PLAYSTATION” is atrademark  
of Sony Computer Entertainment  
Inc.  
trademarks of Dolby  
Laboratories.  
**Manufacturedunder license  
under U.S. Patent #’s:  
5,451,942; 5,956,674;  
5,974,380; 5,978,762;  
6,226,616; 6,487,535;  
®
®
• DivX , DivX Certified and  
associated logos are registered  
trademarks of DivX, Inc. and are  
used under license. (Except for  
U.S. models, BDV-E470.)  
• Windows Media is either a  
registered trademark or trademark  
of Microsoft Corporation in the  
United States and/or other  
countries.  
7,212,872; 7,333,929;  
• Music and video recognition  
technology and related data are  
®
7,392,195; 7,272,567 &  
other U.S. and worldwide  
patents issued & pending.  
DTS and the Symbol are  
registered trademarks, &  
DTS-HD, DTS-HD Master  
Audio, and the DTS logos  
• DLNA , the DLNA Logo and  
®
DLNA CERTIFIED™ are  
trademarks, service marks, or  
certification marks of the Digital  
Living Network Alliance.  
provided by Gracenote .  
Gracenote is the industry standard  
in music recognition technology  
and related content delivery. For  
more information, please visit  
• Other system and product names  
are generally trademarks or  
US  
4
registered trademarks of the  
manufacturers. ™ and ® marks  
are not indicated in this document.  
surround back amplifier, or  
S-AIR receiver is used.  
About These  
Operating  
Instructions  
• The instructions in these  
Operating Instructions  
describe the controls on the  
remote. You can also use the  
controls on the unit if they  
have the same or similar  
names as those on the remote.  
• In this manual, “disc” is used  
as a general reference for  
BDs, DVDs, Super Audio  
CDs, or CDs unless otherwise  
specified by the text or  
illustrations.  
• The instructions in this  
manual are for BDV-E870,  
BDV-E570, BDV-E470,  
BDV-E370, BDV-T57, and  
BDV-T37. BDV-E870 is the  
model used for illustration  
purposes. Any difference in  
operation is clearly indicated  
in the text, for example,  
“BDV-E870.”  
• The items displayed on the  
TV screen may vary  
depending on the area.  
• The default setting is  
underlined.  
• The system is compatible  
with the S-AIR function,  
which allows transmission of  
sound between S-AIR  
products wirelessly. For  
details on the S-AIR function,  
• Notes or instructions for the  
surround amplifier, surround  
back amplifier, or S-AIR  
receiver in these Operating  
Instructions refer only to  
when the surround amplifier,  
US  
5
 
Table of Contents  
Step 3: Performing the Easy  
Step 5: Enjoying Surround  
Selecting the Effect to Suit  
the Source .......................................39  
Selecting the Audio Format, Multilingual  
Tracks, or Channel..........................39  
Enjoying Multiplex Broadcast  
Sound..............................................40  
Using the Control for HDMI Function for  
“BRAVIA” Sync ............................49  
Calibrating the Appropriate Settings  
Automatically .................................51  
Deactivating the Buttons on  
the Unit ...........................................54  
Controlling Your TV with the Supplied  
Remote............................................54  
US  
6
Unpacking  
BDV-E870  
• Front speakers (2)  
• Subwoofer (1)  
• R6 (size AA) batteries (2)  
• Calibration mic (1)  
• FM wire antenna (aerial) (1)  
• Bases (2)  
or  
• Speaker cords (3, blue/gray/  
green)  
• Screws (6)  
• Speaker-bottom covers (2)  
• Surround speakers (2)  
• Center speaker (1)  
• Video cord (1)  
• Operating Instructions  
• Speaker Installation Guide  
• Quick Setup Guide  
• Remote commander  
(remote) (1)  
• End user license agreement  
• Easy Setup Disc (DVD)  
US  
7
 
BDV-E570/BDV-E470/BDV-T57  
• Front speakers (2)  
• FM wire antenna (aerial) (1) • Operating Instructions  
• Quick Setup Guide  
• End user license agreement  
• Easy Setup Disc (DVD)  
or  
For BDV-E570/BDV-T57  
• USB Wireless LAN Adapter  
(UWA-BR100)  
• Speaker cords (6, white/red/  
blue/gray/green/purple)  
• Surround speakers (2)  
• UWA-BR100 External  
cable  
• Video cord (1)  
• Center speaker (1)  
• Subwoofer (1)  
• Remote commander  
(remote) (1)  
For BDV-T57  
• HDMI cable (1)  
• R6 (size AA) batteries (2)  
• Calibration mic (1)  
US  
8
BDV-E370/BDV-T37  
• Front speakers (2)  
• Speaker cords (5, white/red/  
blue/gray/green)  
• Operating Instructions  
• Quick Setup Guide  
• End user license agreement  
For U.S. and Canadian  
models  
• Easy Setup Disc (DVD)  
• Surround speakers (2)  
• Video cord (1)  
For BDV-E370 (Latin  
American models only)/BDV-  
T37  
• HDMI cable (1)  
• Remote commander  
(remote) (1)  
• Center speaker (1)  
• Subwoofer (1)  
• R6 (size AA) batteries (2)  
• Calibration mic (1)  
• FM wire antenna (aerial) (1)  
or  
Preparing the remote  
Insert two R6 (size AA) batteries (supplied) by matching the 3 and # ends on the batteries to the  
markings inside the compartment.  
US  
9
Index to Parts and Control  
For more information, refer to the pages indicated in parentheses.  
Front panel  
FUNCTION  
VOLUME  
VOLUME  
A
"/1 (on/standby)  
C
(USB) port (page 33)  
Used for connecting a USB device.  
Turns on the unit, or sets it to standby mode.  
D Front panel display  
(remote sensor)  
B Play operation buttons  
E
Z (open/close) (page 32)  
Opens or closes the disc tray.  
F Power indicator  
Lights up while the system is turned on.  
N (play)  
Starts or re-starts playback (resume play).  
Plays a slideshow when a disc containing  
JPEG image files is inserted.  
G Disc tray (page 32)  
x (stop)  
Stops playback and remembers the stop  
point (resume point).  
The resume point for a title/track is the last  
point you played or the last photo for a  
photo folder.  
FUNCTION  
Selects the playback source.  
VOLUME +/–  
Adjusts the system’s volume.  
US  
10  
   
Front panel display  
About the indications in the front panel display  
A Displays the current sound format.  
H Flashes when the sleep timer is set.  
(page 54)  
B Lights up when the system is playing  
via the PARTY STREAMING function.  
I S-AIR indicator (only when the wireless  
transmitter (not supplied) is inserted  
into the unit)  
C Lights up when outputting 1920 ×  
1080p/24 Hz video signals.  
Lights up during wireless  
D Lights up when outputting 720p/1080i/  
1080p video signals from the HDMI  
OUT jack or 720p/1080i video signals  
from the COMPONENT VIDEO OUT  
jacks.  
transmission. Flashes when [Standby]  
is set to [On] and the system is in  
standby mode while wireless  
transmission between the unit and  
S-AIR receiver is not activated. (page  
E Lights up when the HDMI OUT jack is  
correctly connected to an HDCP (High-  
bandwidth Digital Content Protection)-  
compliant device with HDMI or DVI  
(Digital Visual Interface) input.  
J Displays system’s status such as  
chapter, title, or track number, time  
information, radio frequency, playing  
status, surround setting, etc.  
F Lights up when a station is received.  
K Lights up when repeat play is  
(Radio only) (page 42)  
activated.  
G Lights up when stereo sound is  
L Displays system’s playing status.  
received. (Radio only) (page 42)  
M Lights up when muting is on.  
US  
11  
 
Rear panel  
Screws*  
VIDEO OUT  
LAN(100)  
ARC  
Y
P
B
/
C
B
P
R
/
CR  
OUT  
COMPONENT VIDEO OUT  
EZW-T100  
AUDIO  
SAT/CABLE  
TV  
SPEAKERS  
SPEAKERS  
DIGITAL IN  
DIGITAL IN  
A. CAL MIC  
ECM-AC2  
FM COAXIAL 75  
ANTENNA  
FRONT  
R
FRONT  
L
SUBWOOFER  
CENTER  
SUR  
R
SUR  
L
COAXIAL  
OPTICAL  
R
AUDIO IN  
L
A
(USB) port (page 33)  
I ANTENNA (FM COAXIAL 75Ω) jack  
B LAN (100) terminal (page 27)  
J TV (DIGITAL IN OPTICAL) jack (page  
C COMPONENT VIDEO OUT jacks (page  
K SAT/CABLE (DIGITAL IN COAXIAL)  
D VIDEO OUT jack (page 23)  
E HDMI OUT jack (page 23)  
jack (page 25)  
L SPEAKERS jacks (page 22)  
F EZW-T100 slot (page 44)  
G AUDIO (AUDIO IN L/R) jacks (page 25)  
H A.CAL MIC jack (pages 28, 51)  
*
CAUTION  
Please do not remove the screws unless you  
are installing the EZW-T100.  
US  
12  
 
B Number buttons (pages 43, 54)  
Enters the title/chapter numbers, radio  
frequencies, etc.  
Remote control  
AUDIO (pages 39, 40)  
Selects the audio format/track.  
ONE-TOUCH TV  
THEATER  
PLAY  
1
SUBTITLE (page 59)  
BRAVIA Sync  
Selects the subtitle language when  
multilingual subtitles are recorded on a BD-  
ROM/DVD VIDEO.  
1
2
5
8
3
6
SLEEP  
4
SYSTEM  
MENU  
9
2
3
4
7
9
SUBTITLE  
D.TUNING (page 42)  
Selects the radio frequencies.  
FAVORITES AUDIO  
0
RED  
D.TUNING  
GREEN  
YELLOW  
BLUE  
C Color buttons (YELLOW/BLUE/RED/  
TOP MENU  
POP UP/ MENU  
GREEN)  
Short cut keys for selecting items on some  
BD menus (can also be used for Java  
interactive operations on BDs).  
RETURN  
OPTIONS  
D TOP MENU  
FUNCTION  
SOUND MODE  
5
6
HOME  
Opens or closes the BD’s or DVD’s Top  
Menu.  
PRESET  
TUNING  
DISPLAY  
REPLAY ADVANCE PRESET  
PLAY  
TUNING  
STOP  
POP UP/MENU  
Opens or closes the BD-ROM’s Pop-up  
Menu, or the DVD’s menu.  
PAUSE  
8
VOL TV VOL  
OPTIONS (page 37)  
Displays the options menu on the TV  
screen.  
MUTING  
TV INPUT  
7
RETURN  
Returns to the previous display.  
Number 5, AUDIO, VOL +, and N buttons  
have a tactile dot. Use the tactile dot as a  
reference when operating the remote.  
C/X/x/c  
Moves the highlight to a displayed item.  
: For TV operations  
(ENTER)  
Enters the selected item.  
E FUNCTION (pages 29, 42)  
Selects the playback source.  
A THEATER (page 50)  
Switches to the optimum video mode for  
watching movies automatically.  
Enters or exits the system’s home menu.  
SOUND MODE (page 39)  
Selects the sound mode.  
ONE-TOUCH PLAY (page 50)  
Activates One-Touch Play.  
TV "/1 (on/standby) (page 54)  
Turns on the TV or sets it to standby mode.  
"/1 (on/standby) (pages 28, 42)  
Turns on the system or sets it to standby  
mode.  
US  
13  
 
F Playback operation buttons  
H DISPLAY (pages 32, 35)  
Displays the playback information on the  
TV screen.  
./> (previous/next)  
Skip to the previous/next chapter, track, or  
file.  
When the function is “TV” or “SAT/  
CABLE” and digital signals are input via  
the DIGITAL IN jack, displays the stream  
information in the front panel display.  
(replay/advance)  
Briefly replay the current scenes for 10  
seconds./Briefly fast forwards the current  
scenes for 15 seconds.  
I
Z (open/close)  
Opens or closes the disc tray.  
SLEEP (page 54)  
Sets the sleep timer.  
m/M (fast reverse/fast forward)  
Fast reverse/fast forward the disc during  
playback. Each time you press the button,  
search speed changes.  
SYSTEM MENU (pages 30, 38, 40, 42)  
Enters the system menu.  
Activates slow-motion play when pressed  
for more than one second in pause mode.  
Plays one frame at a time when pressed in  
pause mode.  
FAVORITES  
Displays the Internet contents added to the  
Favorites List. You can save 18 favorite  
Internet contents.  
N (play)  
Starts or re-starts playback (resume play).  
Plays a slideshow when a disc containing  
JPEG image files is inserted.  
X (pause)  
Pauses or re-starts playback.  
x (stop)  
Stops playback and remembers the stop  
point (resume point). The resume point for  
a title/track is the last point you played or  
the last photo for a photo folder.  
Radio operation buttons  
PRESET +/–  
TUNING +/–  
G MUTING  
Turns off the sound temporarily.  
VOL +/– (page 42)  
Adjusts the volume.  
TV VOL +/–  
Adjusts the TV volume.  
TV INPUT  
Switches the TV’s input source between the  
TV and other input sources.  
US  
14  
Getting Started  
Step 1: Installing the System  
Positioning the speakers  
For the best possible surround sound, place all speakers at the same distance from the listening position  
(A). The distance can be between 0 to 23 feet (0.0 to 7.0 meters).  
If you cannot place the center speaker and surround speakers at the same distance as (A), place them  
within 23 feet (7.0 meters) of the listening position.  
Place the surround speakers to the rear of the listening position (B).  
The subwoofer can be placed anywhere in the room.  
Center speaker  
Subwoofer  
Front left speaker (L)  
Front right speaker (R)  
A
A
A
30  
30  
B
45  
45  
B
A
A
Surround left speaker (L)  
Surround right speaker (R)  
Note  
• Use caution when placing the speakers and/or speaker stands attached to the speakers on a specially treated (waxed,  
oiled, polished, etc.) floor, as staining or discoloration may result.  
• Do not lean or hang on a speaker, as it may fall down.  
US  
15  
   
To add the optional surround back speakers  
You can enjoy 7.1 surround sound by purchasing the Wireless Surround Speaker Kit (WAHT-SBP2,  
optional). The optional product lineup differs depending on the area.  
For the position of the surround back speakers, refer the illustration below (C).  
Center speaker  
Subwoofer  
Front left speaker (L)  
Front right speaker (R)  
Surround left  
speaker (L)  
Surround right  
speaker (R)  
30 30  
45  
45  
C
C
Surround back left speaker (L)  
(optional)  
Surround back right speaker (R)  
(optional)  
Note  
• To use the surround back speakers, set [Surround Back] (page 52) in [Speaker Settings] to [Yes] while performing  
the Easy Setup (page 28).  
Installing the speakers on a wall  
Caution  
• Contact a screw shop or installer regarding the wall material or screws to be used.  
• Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach  
the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where  
reinforcement is applied.  
• Sony is not responsible for accidents or damage caused by improper installation, insufficient wall strength or  
improper screw installation, natural calamity, etc.  
Before installing the front speakers of BDV-E870 on a wall, you need to disassemble the speakers. You  
can install the upper part of the speakers on a wall.  
US  
16  
 
To disassemble the speaker  
(Front speakers of BDV-E870 only)  
1
Disconnect the speaker cords from the speaker.  
Rear of the speaker  
2
Remove the screw (pre-installed) at the rear of the speaker.  
This screw is used when reassembling the speaker. Be sure not to lose the screw.  
Screw  
Rear of the speaker  
3
Disassemble the speaker by lifting the upper part of the speaker.  
Upper part  
Lower part  
Rear of the speaker  
US  
17  
4
Pull out the speaker cord from the bottom of the lower part of the speaker.  
The removed speaker cord is used when installing the speaker on a wall.  
Lower part of the speaker  
,
Speaker cord  
5
Remove the protection paper from the speaker-bottom cover, then attach the speaker-  
bottom cover to the bottom of the upper part of the speaker.  
Bottom of the upper part of  
the speaker  
Protection paper  
,
,
Speaker-bottom cover  
Note  
• When removing the protection paper, pull it off via the section exposed by the notch in the speaker-bottom cover.  
Fully-disassembled illustration  
Upper part of  
the speaker  
Lower part of  
the speaker  
Speaker cord  
Screw  
US  
18  
To install the speakers on a wall  
Before installing the speakers on a wall, connect the speaker cord to the speaker.  
Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord with  
the color tube to 3, and the speaker cord without the color tube to #.  
Color tube  
Front left speaker (L): White  
Front right speaker (R): Red  
Center speaker: Green  
Surround left speaker (L): Blue  
Surround right speaker (R): Gray  
1
Prepare screws (not supplied) that are suitable for the hole on the back of each speaker.  
See the illustrations below.  
Hole on the back of  
4 mm (3/16 inch)  
the speaker  
5 mm  
(7/32 inch)  
30 mm (1 3  
/16 inches)  
10 mm  
13  
(
/32 inch)  
US  
19  
2
Fasten the screws to the wall.  
BDV-E870  
BDV-E570/BDV-E470/BDV-  
E370/BDV-T57/BDV-T37  
For the center speaker  
For the front speakers  
219 mm  
5
(
8
/8 inches)  
304 mm  
12 inches)  
(
8 to 10 mm  
11  
13  
(
/
to  
/
inch)  
32  
32  
8 to 10 mm  
11  
13  
(
/
to  
/
inch)  
32  
32  
For the center speaker  
219 mm  
5
(8  
/8 inches)  
For the other speakers  
8 to 10 mm  
8 to 10 mm  
11  
13  
11  
13  
(
/
to  
/
inch)  
(
/
to  
/
inch)  
32  
32  
32  
32  
For the surround speakers  
8 to 10 mm  
11  
13  
(
/
to  
/
inch)  
32  
32  
US  
20  
3
Hang the speakers on the screws.  
Hole on the back of  
the speaker  
5 mm  
(7/32 inch)  
10 mm  
13  
(
/32 inch)  
Rear of the speaker  
US  
21  
Step 2: Connecting the System  
For connecting the system, read the information on the following pages.  
Do not connect the AC power cord (mains lead) of the unit to a wall outlet (mains) until all the other  
connections are made.  
Note  
• When you connect another component with a volume control, turn down the volume of the other components to a  
level where sound is not distorted.  
Connecting the speakers  
The connector of the speaker cords and the color tube are color-coded depending on the type of speaker.  
Connect the speaker cords to match the color of the SPEAKERS jacks of the unit.  
Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord with  
the color tube to 3, and the speaker cord without the color tube to #. Do not catch the speaker cord  
insulation (rubber covering) in the speaker terminals.  
To connect speaker cords to the unit  
When connecting to the unit, insert the connector until it clicks.  
Rear panel of the unit  
Gray  
(Surround right speaker (R))  
S
R
E
K
A
E
P
S
L
R
U
Blue  
S
R
R
U
S
S
R
E
K
A
E
P
S
(Surround left speaker (L))  
R
E
T
N
E
C
FE  
O
O
W
B
U
S
L
T
N
O
R
F
R
T
N
O
R
F
Green  
(Center speaker)  
Red  
(Front right  
speaker (R))  
Purple  
(Subwoofer)  
White  
(Front left speaker (L))  
To connect speaker cords to the speaker  
Rear or bottom of the speaker  
Color tube  
(+)  
(–)  
Connector  
US  
22  
   
Connecting the TV (Video connection)  
This connection sends a video signal to the TV.  
Depending on the jacks on your TV, select the connection method.  
Rear panel of the unit  
B Component video  
cable (not supplied)  
T
U
O
O
E
ID  
V
ARC  
OUT  
/
CR  
R
P
/
T
CB  
B
P
T
U
O
E
ID  
V
Y
N
N
O
P
M
O
C
A HDMI cable*  
C Video cord (supplied)  
To the component  
video input jacks of  
the TV.  
To the video input  
jack of the TV.  
To the HDMI IN jack  
of the TV.  
* The HDMI cable is supplied with BDV-E370 (Latin American models), BDV-T57, and BDV-T37 only.  
Method 1: HDMI cable (A) connection  
If your TV has an HDMI jack, connect to the TV with an HDMI cable. Picture quality will be improved  
compared to using the component video cable connection or the video cord connection.  
When connecting with the HDMI cable, you need to select the type of output signal (page 57).  
Method 2: Component video cable (B) connection  
If your TV does not have an HDMI jack, but has component video input jacks, connect to the TV with  
a component video cable. Picture quality will be improved compared to using the video cord  
connection.  
When connecting with the component video cable, you need to select the type of output signal (page  
57).  
Method 3: Video cord (C) connection  
If you do not have an HDMI cable or a component video cable, temporarily make this connection.  
US  
23  
 
Connecting the TV (Audio connection)  
This connection sends an audio signal to the unit from the TV. To listen to TV sound via the system,  
perform this connection.  
Rear panel of the unit  
V
T
E
N
L
I
B
L
A
A
IT  
IG  
/C  
T
A
D
S
IN  
L
A
IT  
IG  
D
A
C  
T
P
O
L
IA  
X
A
O
C
Digital optical cord (not  
supplied)  
To the digital optical out jack of  
the TV.  
With a digital audio connection, the system receives a Dolby Digital multiplex broadcast signal and  
you can enjoy multiplex broadcast sound.  
Note  
• When you connect the TV and the unit with an audio cord, see “Connecting the other components” (page 25).  
About Audio Return Channel  
If your TV is compatible with the Audio Return Channel function, an HDMI cable connection also  
sends a digital audio signal from the TV. You do not need to make a separate audio connection for  
listening to TV sound. For details of the Audio Return Channel function, see [Audio Return Channel]  
US  
24  
   
Connecting the other components  
When you connect the system and other components to the TV, video signals from the system and the  
components are sent to the TV, and audio signals from the components are sent to the system as  
follows.  
TV  
Signal flow  
System  
: Video signal  
: Audio signal  
You can enjoy connected components via the system’s speakers.  
• VCR or digital satellite receiver, etc. (not supplied), which has a digital coaxial output jack: D  
• VCR, digital satellite receiver, PlayStation, or portable audio source, etc. (not supplied): E  
Rear panel of the unit  
D Digital coaxial cord  
(not supplied)  
IO  
D
AU  
U
A
R
L
V
T
E
L
IN  
B
L
A
A
IT  
IG  
/C  
T
A
D
S
IN  
L
A
IT  
IG  
D
L
A
IC  
T
P
O
L
IA  
X
A
O
C
E Audio cord  
(not supplied)  
To the digital coaxial out jack  
of the VCR or digital satellite  
receiver, etc.  
To the audio out jacks of the VCR,  
digital satellite receiver, PlayStation,  
or portable audio source, etc.  
US  
25  
   
Connecting the antenna (aerial)  
To connect the antenna (aerial)  
Rear panel of the unit  
L
N
IA  
N
X
A
O
C
M
F
E
T
N
A
or  
FM wire antenna (aerial)  
(supplied)  
Note  
• Be sure to fully extend the FM wire antenna (aerial).  
• After connecting the FM wire antenna (aerial), keep it as horizontal as possible.  
Tip  
• If you have poor FM reception, use a 75-ohm coaxial cable (not supplied) to connect the unit to an outdoor FM  
antenna (aerial) as shown below.  
Outdoor FM antenna (aerial)  
Unit  
FM COAXIAL 75  
ANTENNA  
US  
26  
 
Wireless LAN Adapter and the wireless LAN router  
closer to each other.  
Connecting to the network  
To set the network settings  
Wired Setup  
Use a LAN cable to connect to the LAN (100)  
terminal on the unit.  
For details, see [Network Settings] (page 61)  
and follow the on-screen instructions to  
complete the setup.  
About wireless LAN security  
Since communication via the wireless LAN  
function is established by radio waves, the  
wireless signal may be susceptible to  
interception. To protect wireless  
LAN cable  
(not supplied)  
communication, this system supports various  
security functions. Be sure to correctly  
configure the security settings in accordance  
with your network environment.  
Internet  
Broadband  
router  
ADSL modem/  
cable modem  
No Security  
USB Wireless Setup  
Although you can easily make settings, anyone  
can intercept wireless communication or intrude  
into your wireless network, even without any  
sophisticated tools. Keep in mind that there is a  
risk of unauthorized access or interception of  
data.  
Use a wireless LAN via the USB Wireless LAN  
Adapter (Sony UWA-BR100* only) (supplied  
with BDV-E570 and BDV-T57).  
The USB Wireless LAN Adapter may not be  
available in some regions/countries.  
* As of January 2010.  
WEP  
Turn the unit off before connecting the  
WEP applies security to communications to  
prevent outsiders from intercepting  
communications or intruding into your wireless  
network. WEP is a legacy security technology  
that enables older devices, which do not support  
TKIP/AES, to be connected.  
extension cable or inserting the USB Wireless  
LAN Adapter. After inserting the USB Wireless  
LAN Adapter to the base of the extension cable  
and connecting the extension cable to the  
(USB) port (front or rear), turn the unit on again.  
WPA-PSK (TKIP), WPA2-PSK (TKIP)  
TKIP is a security technology developed to  
correct for the deficiencies of WEP. TKIP  
assures a higher security level than WEP.  
/
C
A  
WPA-PSK (AES), WPA2-PSK (AES)  
AES is a security technology that uses an  
advanced security method that is distinct from  
WEP and TKIP.  
AES assures a higher security level than WEP or  
TKIP.  
LAN cable  
(not supplied)  
USB  
Wireless  
LAN  
Adapter  
Internet  
ADSL modem/ Wireless LAN  
cable modem router  
Note  
• The placement distance between the USB Wireless  
LAN Adapter and your wireless LAN router differs  
depending on the usage environment. If the system  
cannot connect to the network or the network  
connection is unstable, move the USB Wireless LAN  
Adapter to a different position or place the USB  
US  
27  
   
2
Connect the calibration mic to the  
A.CAL MIC jack on the rear panel.  
Step 3: Performing the  
Easy Setup  
Set up the calibration mic at ear level using  
a tripod, etc. (not supplied). The front of  
each speaker should face the calibration  
mic, and there should be no obstruction  
between the speakers and the calibration  
mic.  
Before performing Step3  
Make sure all connections are secure, and then  
connect the AC power cord (mains lead).  
Follow the Steps below to make the basic  
adjustments for using the system.  
Displayed items vary depending on the country  
model.  
Note  
IC  
M
L
A
C
.
A
2
C
-A  
M
C
E
• To use the optional surround back speakers, set  
[Surround Back] in [Speaker Settings] to [Yes]  
"/1  
1
4
7
2
5
8
0
3
6
9
Calibration mic  
C/X/x/c,  
HOME  
1
Turn on the TV.  
3
4
Press [/1 on the unit.  
Switch the input selector on your TV so  
that the signal from the system  
appears on the TV screen.  
The Easy Setup Display for OSD language  
selection appears.  
Easy Setup - OSD  
Select the language to be displayed by this unit.  
English  
Français  
Español  
Português  
US  
28  
         
5
Perform the [Easy Setup]. Follow the  
on-screen instructions to make the  
basic settings using C/X/x/c, and  
Step 4: Selecting the  
Source  
.
For details about [Auto Calibration]  
settings in [Easy Setup], see “Calibrating  
You can select the playback source.  
To recall the Easy Setup Display  
1
4
7
2
5
8
0
3
6
9
1
Press HOME.  
The home menu appears on the TV screen.  
2
3
Press C/c to select  
Press X/x to select [Easy Setup], then  
press  
[Setup].  
FUNCTION  
.
4
Press C/c to select [Start], then press  
.
The Easy Setup Display appears.  
Press FUNCTION repeatedly until the  
desired function appears in the front panel  
display.  
Each time you press FUNCTION, the function  
changes as follows.  
“BD/DVD” t “D. MEDIA” t “TUNER FM”  
t“TV” t “SAT/CABLE” t “AUDIO” t  
“BD/DVD” t …  
Function  
Source  
“BD/DVD”  
“D. MEDIA”  
Disc that is played by the system  
USB device, iPod, BRAVIA  
Internet Video, or DLNA server  
“TUNER FM”  
“TV”  
Component (TV, etc.) that is  
connected to the TV (DIGITAL  
IN OPTICAL) jack on the rear  
panel, or a TV compatible with the  
Audio Return Channel function  
that is connected to the HDMI  
OUT jack on the rear panel  
“SAT/CABLE” Component that is connected to  
the SAT/CABLE (DIGITAL IN  
COAXIAL) jack on the rear panel  
“AUDIO”  
Component that is connected to  
the AUDIO (AUDIO IN L/R)  
jacks on the rear panel (page 25)  
US  
29  
   
Step 5: Enjoying Surround Sound  
After performing the previous Steps and starting playback, you can easily enjoy surround sound. You  
can also select pre-programmed surround settings that are tailored to different kinds of sound sources.  
They bring the exciting and powerful sound of movie theaters into your home.  
1
4
7
2
5
8
0
3
6
9
SYSTEM MENU  
X/x/c,  
Selecting surround settings based on your listening preference  
1
2
Press SYSTEM MENU.  
Press X/x repeatedly until “SUR.SETTING” appears in the front panel display, then  
press  
or c.  
3
Press X/x repeatedly until the surround setting you want appears in the front panel  
display.  
See the table below for surround sound setting descriptions.  
4
5
Press  
.
The setting is made.  
Press SYSTEM MENU.  
The system menu turns off.  
About speaker output of each surround setting  
The table below describes the options when you connect all the speakers to the unit.  
The default setting is “A.F.D. MULTI.”  
Sound from  
Surround setting  
Effect  
Depending on the source.  
“A.F.D. STD”  
(AUTO FORMAT  
The system discriminates the sound format of the source and  
presents sound as it was recorded/encoded.  
DIRECT STANDARD)  
US  
30  
     
Sound from  
Surround setting  
Effect  
“A.F.D. MULTI”  
(AUTO FORMAT  
DIRECT MULTI)  
• 2 channel source: The system simulates surround sound  
from 2 channel sources and outputs sound from the 5.1  
channel speakers by duplicating 2 channel source sound  
across each speaker.  
• Multi-channel source: The system outputs sound from the  
speakers depending on the number of channels of the  
source.  
“PRO LOGIC”  
“PLII MOVIE”  
• 2 channel source: The system simulates surround sound  
from 2 channel sources and outputs sound from the 5.1  
channel speakers.  
– “PRO LOGIC” performs Dolby Pro Logic decoding.  
– “PLII MOVIE” performs Dolby Pro Logic II movie  
mode decoding.  
• Multi-channel source: The system outputs sound from the  
speakers depending on the number of channels of the  
source.  
“NEO6 CIN”  
“NEO6 MUS”  
• 2 channel source: The system simulates surround sound  
from 2 channel sources and produces 6.1 channel sound.  
– “NEO6 CIN” performs DTS Neo:6 Cinema mode  
decoding.  
– “NEO6 MUS” performs DTS Neo:6 Music mode  
decoding.  
• Multi-channel source: The system outputs sound from the  
speakers depending on the number of channels of the  
source.  
“2CH STEREO”  
The system outputs the sound from the front speakers and  
subwoofer regardless of sound format or number of channels.  
Multi-channel surround formats are downmixed to 2  
channels.  
Note  
• When you select “A.F.D. MULTI,” depending on the disc or source, the beginning of the sound may be cut off  
while the optimum mode is automatically selected. To avoid cutting the sound, select “A.F.D. STD.”  
• When bilingual broadcast sound is input, “PRO LOGIC” and “PLII MOVIE” are not effective.  
• Depending on the input stream, the surround settings may not be effective.  
• When changing the surround setting while using the S-AIR receiver, sound from the S-AIR receiver may skip.  
• When you play a Super Audio CD, surround settings are not activated.  
Tip  
• The system memorizes the last surround setting selected for each function.  
Whenever you select a function such as “BD/DVD” or “TUNER FM,” the surround setting that was last applied to  
the function is automatically applied again. For example, if you select “BD/DVD” with “PRO LOGIC” as the  
surround setting, then change to another function, and then return to “BD/DVD,” “PRO LOGIC” will be applied  
again.  
US  
31  
Tip  
• Delete unnecessary data in internal memory or USB  
Playback  
memory. Select [Erase BD Data] in  
[Video] to  
delete unnecessary data. If you use USB memory as  
local storage, all saved data in the [BUDA/BUDB]  
folder is deleted. Make sure to backup any video/  
music/photo data in the [BUDA/BUDB] folder.  
Playing a Disc  
For playable discs, see “Playable Discs”  
Enjoying Blu-ray 3D  
1
2
Switch the input selector on your TV so  
that the signal from the system  
appears on your TV screen.  
You can enjoy Blu-ray 3D Discs with the 3D  
logo*.  
Press Z, and place a disc on the disc  
tray.  
*
1
Prepare for Blu-ray 3D Disc playback.  
• Connect the system to your 3D-  
compatible TV using a High-Speed  
HDMI cable (not supplied).  
• Set [3D Output Setting] and [TV Screen  
Size Setting for 3D] in [Screen Settings]  
2
Insert a Blu-ray 3D Disc.  
The operation method differs depending on  
the disc. Refer to the operating instructions  
supplied with the disc.  
3
Press Z to close the disc tray.  
appears on the home menu and playback  
starts.  
Tip  
If playback does not start automatically,  
• Refer also to the operating instructions of your 3D-  
compatible TV.  
select  
in the  
[Video],  
[Music], or  
.
[Photo] category, and press  
Enjoying BONUSVIEW/BD-LIVE  
Some BD-ROMs with “BD-LIVE Logo*” have  
bonus content and other data that can be  
downloaded for enjoyment.  
*
1
2
Prepare for BONUSVIEW/BD-LIVE.  
• Connect the unit to a network (page 27).  
• Set [BD Internet Connection] to [Allow]  
Insert a BD-ROM with BONUSVIEW/  
BD-LIVE.  
The operation method differs depending on  
the disc. Refer to the operating instructions  
of the disc.  
US  
32  
             
Displaying the play information  
Playing from a USB  
Device  
You can check the playback information, etc.,  
by pressing DISPLAY.  
The displayed information differs depending on  
the disc type and player status.  
You can play video/music/photo files on the  
connected USB device.  
For playable types of files, see “Playable Types  
Example: when playing a BD-ROM  
1
Connect the USB device to the  
(USB) port on the unit.  
Refer to the operating instructions of the  
USB device before connecting.  
USB device  
A
B
C
D
Output resolution/Video frequency  
Title number or name  
The currently selected audio setting  
Available functions (  
subtitle)  
angle,  
audio,  
E
Playback information  
Displays disc type, play mode, repeat type,  
video codec, bit rate, playing status bar,  
playing time, total time  
USB device  
F
G
Chapter number  
2
3
Press C/c to select  
[Video],  
The currently selected angle  
[Music], or  
[Photo].  
Press X/x to select  
(front)] or [USB device (rear)], then  
[USB device  
press  
.
Note  
• Do not remove the USB device during  
operation. To avoid data corruption or damage  
to the USB device, turn the system off when  
connecting or removing the USB device.  
US  
33  
     
To operate the iPod using the  
remote  
You can operate the iPod using the buttons on  
the remote. The following table shows an  
example of buttons that can be used.  
Enjoying an iPod  
You can enjoy the sound and charge the battery  
of an iPod via the system.  
Compatible iPod models  
The compatible iPod models are as follows.  
Update your iPod with the latest software before  
using with the system.  
Press  
Operation  
N, X  
Same operation as the N/X button  
of the iPod.  
x
Pause.  
m or M  
. or >  
Fast reverse or forward.  
Same operation as the . or >  
buttons of the iPod.  
DISPLAY,  
RETURN,  
C
Same operation as the MENU button  
of the iPod.  
X/x  
Same operation as the Click Wheel  
of the iPod.  
, c  
Same operation as the Center button  
of the iPod.  
Note  
• The iPod is charged when connected to the system  
while the system is turned on.  
• You cannot transfer songs onto the iPod.  
• Sony cannot accept responsibility in the event that  
data recorded to iPod is lost or damaged when using  
an iPod connected to this unit.  
• This product has been designed specifically to work  
with iPod and has been certified to meet Apple  
performance standards.  
1
Connect the iPod to the front  
port on the unit with the iPod’s USB  
cable.  
(USB)  
• Do not remove the iPod during operation. To avoid  
data corruption or damage to the iPod, turn the system  
off when connecting or removing the iPod.  
2
3
Press C/c to select  
Press X/x to select [iPod (front)],  
then press  
[Music].  
.
The sound from the iPod is played on the  
system.  
You can operate the iPod using the buttons  
on the remote.  
For operation details, refer to the operating  
instructions of the iPod.  
US  
34  
 
Playing files stored on a DLNA  
server (DLNA Player)  
Playing via a Network  
You can play video/music/photo files on your  
home server, such as a DLNA-certified network  
audio system or a PC with software that enables  
a DLNA-certified server function, by  
Streaming BRAVIA Internet  
Video  
BRAVIA Internet Video serves as a gateway  
delivering the selected Internet content and a  
variety of on-demand entertainment straight to  
your unit.  
connecting the system to your home network.  
1
Prepare for playing files on a DLNA  
server.  
• Connect the unit to a network (page 27).  
• Set [Connection Server Settings]  
1
Prepare for BRAVIA Internet Video.  
Connect the unit to a network (page 27).  
2
3
Press C/c to select  
[Video],  
2
3
Press C/c to select  
[Video],  
[Music], or [Photo].  
[Music], or [Photo].  
Press X/x to select an Internet content  
provider icon, then press  
Press X/x to select a DLNA server, then  
press  
.
.
When the Internet content list has not been  
retrieved, it will be represented by an  
unacquired icon or a new icon.  
The file list or folder list appears.  
Playing the same audio in  
different rooms (PARTY  
STREAMING)  
To use the control panel  
The control panel appears when the video file  
starts playing. The displayed items may differ  
depending on Internet content providers.  
To display again, press DISPLAY.  
Note  
• If [Party Auto Start] (page 62) is not displayed on the  
TV screen, this function may be available via a future  
update. However, the function may not be available  
in some regions/countries.  
A
B
Control display  
Press C/X/x/c or  
for playback operations.  
Playing status bar  
Status bar, cursor indicating the current  
position, playing time, duration of the video  
file  
C
D
The next video file name  
The currently selected video file name and  
rating  
US  
35  
         
You can play the same audio at the same time  
across all Sony components which are  
compatible with the PARTY STREAMING  
function.  
The component that plays audio for the party  
through the use of [Start Party] is called the  
“party host.” A component that is invited to the  
party from the party host and plays the same  
audio as the party host is called a “party guest.”  
To close a party  
For the party host  
Press x, then press HOME.  
For a party guest  
Press OPTIONS, press X/x to select [Close  
Party], then press  
.
To leave from a party  
(for a party guest only)  
To start a party  
(for the party host only)  
Press OPTIONS, press X/x to select [Leave  
Party], then press  
.
You can use other components to play the  
content that is playing on the system.  
Note  
• The sale and product lineup of products that are  
compatible with the PARTY STREAMING function  
differ depending on the area.  
1
Turn on the system and other Sony  
components compatible with the  
PARTY STREAMING function.  
Make sure that each component is  
connected to the network.  
Operating the system with a  
DLNA controller (renderer)  
2
Press C/X/x/c to select the audio  
content in  
[Music] or a radio station.  
Note  
For selecting a radio station, see “Listening  
• If [Renderer Options] (page 61) is not displayed on  
the TV screen, this function may be available via a  
future update. However, the function may not be  
available in some regions/countries.  
3
4
Press OPTIONS.  
Press X/x to select [Start Party], then  
press  
.
You can operate the system with a DLNA  
controller.  
For details of operation, see the operating  
instructions of the DLNA controller.  
All party guests’ components start playing  
the same audio content as the party host.  
To join in a party  
(for a party guest only)  
Note  
• Do not operate the system with the supplied remote  
when operating the system by the DLNA controller.  
You can use the system to play the content that  
is playing on other components.  
Tip  
• The system is compatible with the “Play To” function  
of Windows Media Player 12 that comes standard  
with Windows 7.  
1
Turn on the system and other Sony  
components compatible with the  
PARTY STREAMING function.  
®
Make sure that each component is  
connected to the network.  
2
Start a party on another networked  
component.  
3
4
Press C/c to select  
[Music].  
Press X/x to select  
[Party], then  
press  
Press X/x to select the party host that  
you set up in Step 2, then press  
.
5
.
US  
36  
[Video] only  
Available Options  
Items  
Details  
Various settings and playback operations are  
available by pressing OPTIONS. The available  
items differ depending on the situation.  
[3D Output Setting] Sets whether or not to output  
3D video automatically.  
[Video Settings]  
• [Picture Quality Mode]:  
Selects the picture settings  
for different lighting  
environments.  
Common options  
Items  
Details  
• [FNR]: Reduces the random  
noise appearing in the  
picture.  
[Playback History  
List]  
Displays titles/tracks in the  
playback history of a  
BD-ROM/DVD-ROM/  
CD-DA (music CD) using  
Gracenote technology (except  
for BDV-E370 (U.S. models)).  
• [BNR]: Reduces the  
mosaic-like block noise in  
the picture.  
• [MNR]: Reduces minor  
noise around the picture  
outlines (mosquito noise).  
[Search History]  
[Search Contents]  
Searches for related  
informationbased on keywords  
from Gracenote via the  
Information Display (except  
for BDV-E370 (U.S. models)).  
[Play/Pause]  
[Top Menu]  
Starts or pauses playback.  
Displays the BD’s or DVD’s  
Top Menu.  
Searches for BRAVIA  
Internet Video content based  
on keywords from Gracenote  
via the Information Display  
(except for BDV-E370 (U.S.  
models)).  
[Menu/Popup Menu] Displays the BD-ROM’s  
Pop-up Menu or DVD’s  
menu.  
[Title Search]  
Searches for a title on BD-  
ROMs/DVD VIDEOs and  
starts playback from the  
beginning.  
[Repeat Setting]  
[Favorites List]  
[Play/Stop]  
Sets the repeat play.  
Displays the Favorites List.  
Starts or stops playback.  
[Chapter Search]  
[Angle]  
Searches for a chapter and  
starts playback from the  
beginning.  
[Play from beginning] Plays the item from the  
beginning.  
[Information Display] Displays information on the  
BD-ROM/DVD-ROM/  
Switches to other viewing  
angles when multi-angles are  
recorded on BD-ROMs/DVD  
VIDEOs.  
CD-DA (music CD) by using  
Gracenote technology (except  
for BDV-E370 (U.S. models)).  
[Add to Favorites]  
Adds an Internet content to  
the Favorites List.  
[Music] only  
[Remove from  
Favorites]  
Erases an Internet content  
from the Favorites List.  
Items  
Details  
[Add Slideshow  
BGM]  
Registers music files in the  
USB memory as slideshow  
background music.  
[Start Party]  
Starts a party with the  
selected source.  
This item may not appear  
depending on the source.  
[Leave Party]  
Leaves from a party which  
the system is participating in.  
The PARTY STREAMING  
function continues among  
other participating devices.  
[Close Party]  
Closes a party which the  
system is participating in. The  
PARTY STREAMING  
function ends for all other  
participating devices.  
US  
37  
   
[Photo] only  
Adjusting the delay between  
the picture and sound  
(A/V SYNC)  
Items  
Details  
[Slideshow]  
Starts a slideshow.  
Changes the slideshow speed.  
[Slideshow Speed]  
[Slideshow Effect]  
Sets the effect when playing a  
slideshow.  
When the sound does not match the pictures on  
the TV screen, you can adjust the delay between  
the picture and sound.  
[Slideshow BGM]  
• [Off]: Turns off the  
function.  
• [My Music from USB]: Sets  
the music files registered in  
[Add Slideshow BGM]. If  
no music file is registered,  
[(Not registered)] is  
displayed.  
1
2
Press SYSTEM MENU.  
Press X/x repeatedly until “A/V SYNC”  
appears in the front panel display, then  
press  
or c.  
3
Press X/x to adjust the delay between  
the picture and sound.  
• [Play from disc]: Sets the  
tracks on CD-DAs (music  
CDs).  
You can adjust from 0 ms to 300 ms in 25  
ms increments.  
[Rotate Left]  
Rotates the photo  
counterclockwise by  
90 degrees.  
4
Press  
.
The setting is made.  
[Rotate Right]  
[View Image]  
Rotates the photo clockwise  
by 90 degrees.  
5
Press SYSTEM MENU.  
Displays the selected picture.  
The system menu turns off.  
Note  
• Depending on the input stream, A/V SYNC may not  
be effective.  
US  
38  
       
• When changing the sound mode while using the  
S-AIR receiver, sound from the S-AIR receiver may  
skip.  
Sound Adjustment  
• When you play a Super Audio CD, this function does  
not work.  
Selecting the Effect to  
Suit the Source  
Selecting the Audio  
Format, Multilingual  
Tracks, or Channel  
When the system is playing a BD/DVD VIDEO  
or DATA CD/DATA DVD (DivX video files*)  
recorded in multiple audio formats (PCM,  
Dolby Digital, MPEG audio, or DTS) or  
multilingual tracks, you can change the audio  
format or language.  
You can select a suitable sound mode for movies  
or music.  
1
4
7
2
5
8
0
3
6
9
SOUND  
MODE  
With a CD, you can select the sound from the  
right or left channel and listen to the sound of the  
selected channel through both the right and left  
speakers.  
* Except for U.S. models, BDV-E470.  
Press SOUND MODE repeatedly during  
playback until the desired mode appears in  
the front panel display.  
1
4
7
2
5
8
0
3
6
9
• “AUTO”: The system selects “MOVIE” or  
“MUSIC” automatically to produce the sound  
effect depending on the disc or sound stream.  
• “MOVIE”: The system provides the sound for  
movies.  
AUDIO  
• “MUSIC”: The system provides the sound for  
music.  
• “SPORTS”: The system adds reverberation for  
sports programs.  
• “NEWS”: The system provides the sound for  
voice programs, such as news.  
• “GAME ROCK”: The system provides the  
sound for music/rhythm games.  
Press AUDIO repeatedly during playback to  
select the desired audio signal.  
The audio information appears on the TV  
screen.  
Note  
• Depending on the disc or source, when you select  
“AUTO,” the beginning of the sound may be cut off  
as the system selects the optimum mode  
automatically. To avoid cutting the sound, select  
other than “AUTO.”  
x BD/DVD VIDEO  
Depending on the BD/DVD VIDEO, the choice  
of language varies.  
When 4 digits are displayed, they indicate a  
(page 77) to confirm which language the code  
represents. When the same language is  
• Depending on the input stream, the sound mode may  
not be effective.  
US  
39  
             
displayed two or more times, the BD/DVD  
VIDEO is recorded in multiple audio formats.  
1
4
7
2
5
8
0
3
6
9
x DVD-VR  
The types of sound tracks recorded on a disc are  
displayed.  
AUDIO  
Example:  
• [ Stereo]  
• [ Stereo (Audio1)]  
• [ Stereo (Audio2)]  
• [ Main]  
• [ Sub]  
• [ Main/Sub]  
Note  
• [ Stereo (Audio1)] and [ Stereo (Audio2)] do not  
appear when only one audio stream is recorded on the  
disc.  
Press AUDIO repeatedly until the desired  
signal appears in the front panel display.  
• “MAIN”: Sound of the main language will be  
output.  
x DATA CD (DivX video file)/DATA DVD  
(DivX video file) (Except for U.S. models,  
BDV-E470)  
• “SUB”: Sound of the sub language will be  
output.  
The choice of DATA CD or DATA DVD audio  
signal formats differs, depending on the DivX  
video file contained on the disc. The format  
appears on the TV screen.  
• “MAIN/SUB”: Mixed sound of both the main  
and sub languages will be output.  
x CD  
Using the Sound Effect  
• [ Stereo]: The standard stereo sound.  
• [ 1/L]: The sound of the left channel  
(monaural).  
• [ 2/R]: The sound of the right channel  
(monaural).  
1
4
7
2
5
8
0
3
6
9
SYSTEM  
MENU  
Enjoying Multiplex  
Broadcast Sound  
(DUAL MONO)  
C/X/x/c,  
You can enjoy multiplex broadcast sound when  
the system receives or plays a Dolby Digital  
multiplex broadcast signal.  
Note  
• To receive the Dolby Digital signal, you need to  
connect a TV or other component to the unit with a  
digital coaxial or optical cord (pages 24, 25). If your  
TV is compatible with the Audio Return Channel  
function (page 51), you can receive a Dolby Digital  
signal via an HDMI cable.  
Enjoying sound at low volume  
You can enjoy sound effects or dialog, as you  
would in a movie theater, even at low volume. It  
is useful for watching movies at night.  
1
Press SYSTEM MENU.  
US  
40  
           
2
3
Press X/x repeatedly until “NIGHT  
MODE” appears in the front panel  
display, then press  
or c.  
Press X/x to select a setting.  
• “NIGHT ON”: On.  
• “NIGHT OFF”: Off.  
4
Press SYSTEM MENU.  
The system menu turns off.  
Note  
• When sound is output from the center speaker, this  
effect is more pronounced, as speech (movie dialog,  
etc.) is easy to hear. When sound is not output from  
the center speaker, the system optimally adjusts the  
volume.  
Reinforcing bass frequencies  
You can reinforce bass frequencies.  
1
2
Press SYSTEM MENU.  
Press X/x repeatedly until “D.BASS”  
appears in the front panel display, then  
press  
or c.  
3
4
Press X/x to select a setting.  
• “D.BASS ON”: On.  
• “D.BASS OFF”: Off.  
Press SYSTEM MENU.  
The system menu turns off.  
US  
41  
     
3
Adjust the volume by pressing  
VOL +/–.  
Tuner  
If an FM program is noisy  
If an FM program is noisy, you can select  
monaural reception. There will be no stereo  
effect, but reception will improve.  
Listening to the Radio  
You can enjoy radio sound with the system’s  
speakers.  
1
2
Press SYSTEM MENU.  
Press X/x repeatedly until “FM MODE”  
appears in the front panel display.  
"/1  
1
4
7
2
5
8
0
3
6
9
Number  
buttons  
SYSTEM  
MENU  
D.TUNING  
3
4
Press  
or c.  
C/X/x/c,  
Press X/x to select “MONO.”  
• “STEREO”: Stereo reception.  
• “MONO”: Monaural reception.  
HOME  
PRESET +/–  
FUNCTION  
TUNING +/–  
5
Press SYSTEM MENU.  
x
The system menu turns off.  
VOL +/–  
To turn off the radio  
Current station  
Current band and preset number  
Press "/1.  
FM  
7
Presetting radio stations  
You can preset up to 20 stations. Before tuning,  
make sure to turn down the volume to minimum.  
88.00 MHz  
1
Press FUNCTION repeatedly until  
“TUNER FM” appears in the front panel  
display.  
2
Press and hold TUNING +/– until the  
auto scanning starts.  
1
2
Press FUNCTION repeatedly until  
“TUNER FM” appears in the front panel  
display.  
Scanning stops when the system tunes in a  
station.  
Select the radio station.  
3
4
Press SYSTEM MENU.  
Automatic tuning  
Press X/x repeatedly until “MEMORY”  
appears in the front panel display, then  
Press and hold TUNING +/– until the auto  
scanning starts.  
press  
or c.  
[Auto Tuning] appears on the TV screen.  
Scanning stops when the system tunes in a  
station.  
A preset number appears in the front panel  
display.  
To stop the automatic tuning manually,  
press TUNING +/– or x.  
Manual tuning  
Press TUNING +/– repeatedly.  
US  
42  
         
5
6
Press X/x to select the preset number  
you want.  
Selecting a radio station by  
inputting a frequency directly  
When you know the frequencies, you can select  
radio stations by inputting the frequencies  
directly.  
Tip  
• You can select the preset number directly by  
pressing the number buttons.  
1
Press FUNCTION repeatedly until  
“TUNER FM” appears in the front panel  
display.  
Press  
.
“COMPLETE” appears in the front panel  
display, and the station is stored.  
2
3
Press D.TUNING.  
7
8
Repeat Steps 2 to 6 to store other  
stations.  
Press the number buttons to select the  
frequencies.  
Press SYSTEM MENU.  
4
Press  
.
The system menu turns off.  
To change the preset number  
Select the desired preset number by pressing  
PRESET +/–, then perform the procedure from  
Step 3.  
Selecting the preset station  
1
Press FUNCTION repeatedly until  
“TUNER FM” appears in the front panel  
display.  
The last received station is tuned in.  
2
Press PRESET +/– repeatedly to select  
the preset station.  
The preset number and frequency appear on  
the TV screen and front panel display.  
Each time you press the button, the system  
tunes in one preset station.  
Tip  
• You can select the preset station number directly  
by pressing the number buttons.  
US  
43  
 
Note  
• When you insert the wireless transmitter/transceiver,  
make sure that the AC power cord (mains lead) is not  
connected to a wall outlet (mains).  
• Do not touch the terminals of the wireless transmitter/  
transceiver.  
External Audio Device  
Using an S-AIR Product  
When you purchase the S-AIR product, you  
need to perform the following settings to  
activate wireless transmission.  
To insert the wireless transmitter  
into the unit  
1
Remove the screws directly below the  
mark.  
About S-AIR products  
There are two types of S-AIR product.  
• S-AIR main unit (this unit): This is for  
transmitting sound. You can use up to three  
S-AIR main units. (The number of usable  
S-AIR main units depends on the use  
environment.)  
Rear of the unit  
EZW-T100  
• S-AIR sub unit: This is for receiving sound.  
Surround amplifier (optional): You  
can enjoy surround speaker sound  
wirelessly.  
-T100  
EZW  
S-AIR receiver (optional): You can  
enjoy system sound in another room.  
Room A  
Note  
S-AIR main unit  
• Remove the screws that are indicated in the  
illustration. Do not remove other screws.  
2
Insert the wireless transmitter.  
Rear of the unit  
EZW-T100  
S-AIR sub unit  
(surround amplifier)  
Room B  
-T100  
EZW  
S-AIR sub unit  
(S-AIR receiver)  
(not supplied)  
Inserting the wireless  
transmitter/transceiver  
Note  
• Insert the wireless transmitter with the S-AIR  
logo facing up.  
• Insert the wireless transmitter so that the V  
marks are aligned.  
To make use of the S-AIR function, you need to  
insert the wireless transmitter into the unit and  
the wireless transceiver into the S-AIR sub unit.  
• Do not insert anything other than the wireless  
transmitter into the EZW-T100 slot.  
US  
44  
         
3
Make sure to use the same screws to  
secure the wireless transmitter.  
3
4
Press C/c to select  
Press X/x to select [System Settings],  
then press  
Press X/x to select [S-AIR Settings],  
then press  
[Setup].  
.
Rear of the unit  
5
.
EZW-T100  
The [S-AIR Settings] display appears.  
6
7
Press X/x to select [ID], then press  
.
Press X/x to select the desired ID.  
You can select any ID (A, B, or C).  
8
9
Press  
.
The setting is made.  
Set the S-AIR sub unit to the same ID.  
Wireless transmission is activated as  
follows (example):  
Note  
• Do not use other screws to fasten the wireless  
transmitter.  
ID A  
To insert the wireless  
transceiver into the S-AIR sub  
unit  
For details on installing the wireless transceiver  
into the S-AIR sub unit, such as a surround  
amplifier or S-AIR receiver, see the operating  
instructions of the S-AIR sub unit.  
ID A  
ID A  
Tip  
• When you change the S-AIR configuration, Sony  
recommends that you perform [Auto Calibration].  
To set the ID of the surround  
amplifier  
Refer to the operating instructions of the  
surround amplifier.  
Setting the S-AIR ID to activate  
wireless transmission  
For the surround amplifier  
For the S-AIR receiver  
To set the ID of the S-AIR  
receiver  
Refer to the operating instructions of the S-AIR  
receiver.  
To enjoy a 7.1 channel system  
Simply by matching the ID of the unit and the  
S-AIR sub unit, you can activate wireless  
transmission.  
You can enjoy the more realistic surround sound  
effect of 7.1 channels when you use the Wireless  
Surround Speaker Kit (WAHT-SBP2, optional).  
For details, refer to the operating instructions of  
the Wireless Surround Speaker Kit.  
To set the ID of the unit  
1
Press "/1 on the unit.  
In this case, set [Surround Back] in [Speaker  
Settings] to [Yes] (page 52).  
The system turns on.  
2
Press HOME.  
The home menu appears on the TV screen.  
US  
45  
   
Enjoying the system’s sound in  
another room  
Enjoying the S-AIR receiver  
while the unit is in standby  
mode  
For the S-AIR receiver  
For the S-AIR receiver  
You can enjoy the system’s sound in another  
room by using the S-AIR receiver.  
You can enjoy the S-AIR receiver while the unit  
is in standby mode by setting [Standby] to [On].  
1
Press HOME.  
The home menu appears on the TV screen.  
1
Press HOME.  
2
3
Press C/c to select  
Press X/x to select [System Settings],  
then press  
Press X/x to select [S-AIR Settings],  
then press  
[Setup].  
The home menu appears on the TV screen.  
2
3
Press C/c to select  
Press X/x to select [System Settings],  
then press  
Press X/x to select [S-AIR Settings],  
then press  
[Setup].  
.
4
.
.
4
The [S-AIR Settings] display appears.  
.
5
6
Press X/x to select [Mode], then press  
The [S-AIR Settings] display appears.  
.
5
6
Press X/x to select [Standby], then  
Press X/x to select the desired setting.  
press  
.
• [Party]: The S-AIR receiver outputs  
sound according to functions set on the  
unit.  
Press X/x to select the desired setting.  
• [On]: You can enjoy the S-AIR receiver  
while the unit is in standby mode or turned  
on. The power consumption during  
standby mode increases.  
• [Off]: You cannot enjoy the S-AIR  
receiver while the unit is in standby mode.  
• [Separate]: You can set the desired  
function for the S-AIR receiver while unit  
functions do not change.  
7
8
Press  
.
The setting is made.  
7
Press  
.
When you select [Separate] in Step 6,  
press S-AIR CH on the S-AIR receiver  
to select the function.  
The setting is made.  
Note  
• When you turn the system off while [Standby] is set  
to [On], “S-AIR” flashes (when wireless transmission  
between the unit and S-AIR receiver is not activated),  
or lights up (when wireless transmission between the  
unit and S-AIR receiver is activated) in the front  
panel display.  
The S-AIR receiver’s function changes as  
follows.  
“MAIN UNIT” t “TUNER FM” t  
“AUDIO” t …  
To enjoy the same function as the unit,  
select “MAIN UNIT.”  
9
Adjust the volume on the S-AIR  
receiver.  
US  
46  
   
8
9
Start pairing of the S-AIR sub unit.  
Identifying the unit with a  
specific S-AIR sub unit  
(Pairing operation)  
For the surround amplifier  
For the S-AIR receiver  
x For the surround amplifier  
Refer to the operating instructions of the  
surround amplifier.  
x For the S-AIR receiver  
Refer to the operating instructions of the  
S-AIR receiver.  
Press C/c to select [Start], then press  
When using S-AIR products, neighbors may  
also receive your system’s sound if IDs are the  
same, or you may receive sound from neighbors.  
To prevent this, you can identify the unit with a  
specific S-AIR sub unit by performing the  
pairing operation.  
When you perform pairing, wireless  
transmission is activated between the paired  
main unit and S-AIR sub unit only.  
.
The unit starts pairing.  
The PAIRING indicator of the surround  
amplifier flashes when pairing starts.  
When wireless transmission is activated,  
the PAIRING indicator of the surround  
amplifier turns on.  
To cancel pairing, select [Cancel].  
1
2
Place the S-AIR sub unit that you want  
to pair near the unit.  
Note  
• Perform pairing within several minutes of Step  
9. If you do not, [Pairing failed. Retry?] appears  
on the TV screen. To continue pairing, select  
[OK] and press , then start again from Step 8.  
To cancel pairing, select [Cancel].  
Match the IDs of the unit and the S-AIR  
sub unit.  
• To set the ID of the unit, see “To set the ID  
• To set the ID of the surround amplifier,  
refer to the operating instructions of the  
surround amplifier.  
To cancel pairing  
Change the ID of the main and sub unit  
• To set the ID of the S-AIR receiver, refer  
to the operating instructions of the S-AIR  
receiver.  
If wireless transmission is  
unstable  
For the surround amplifier  
For the S-AIR receiver  
3
Press HOME.  
The home menu appears on the TV screen.  
4
5
Press C/c to select  
Press X/x to select [System Settings],  
then press  
Press X/x to select [S-AIR Settings],  
then press  
[Setup].  
If you use multiple wireless systems, such as  
wireless LAN or Bluetooth, the transmission of  
S-AIR signals or other wireless signals may be  
unstable. In this case, the transmission may be  
improved by changing the following [RF  
Change] setting.  
.
6
.
The [S-AIR Settings] display appears.  
7
Press X/x to select [Pairing], then  
press  
.
1
Press HOME.  
The home menu appears on the TV screen.  
2
3
Press C/c to select  
Press X/x to select [System Settings],  
then press  
[Setup].  
.
US  
47  
   
4
Press X/x to select [S-AIR Settings],  
then press  
.
The [S-AIR Settings] display appears.  
5
6
Press X/x to select [RF Change], then  
press  
Press X/x to select the desired setting,  
then press  
.
.
• [Auto]: Normally select this. The system  
changes [RF Change] to [On] or [Off]  
automatically.  
• [On]: The system transmits sound by  
searching for the better channel for  
transmitting.  
• [Off]: The system transmits sound by  
fixing the channel for transmitting.  
7
8
Press  
.
The setting is made.  
When you set [RF Change] to [Off],  
select the ID so that wireless  
transmission is most stable (page 45).  
Note  
• In most cases, you will not need to change this  
setting.  
– If [RF Change] is set to [Off], transmission  
between the unit and S-AIR sub unit can be  
performed using one of the following channels.  
– S-AIR ID A: equivalent channel for IEEE  
802.11b/g channel 1  
– S-AIR ID B: equivalent channel for IEEE  
802.11b/g channel 6  
– S-AIR ID C: equivalent channel for IEEE  
802.11b/g channel 11  
• The transmission may be improved by changing the  
transmission channel (frequency) of the other  
wireless system(s). For details, refer to the operating  
instructions of the other wireless system(s).  
US  
48  
• The Control for HDMI function may not work if you  
connect other than a Sony component, even if the  
component is compatible with the Control for HDMI  
function.  
Other Operations  
Using the Control for  
HDMI Function for  
“BRAVIA” Sync  
This function is available on TVs with the  
“BRAVIA” Sync function.  
By connecting Sony components that are  
compatible with the Control for HDMI function  
with an HDMI cable, operation is simplified as  
below:  
Preparing for the Control for  
HDMI function  
(Control for HDMI - Easy Setting)  
If your TV is compatible with the Control for  
HDMI - Easy Setting function, you can set the  
system’s [Control for HDMI] function  
automatically by setting the TV. For details,  
refer to the operating instructions of the TV.  
– System Power Off (page 50)  
– One-Touch Play (page 50)  
– Theater Mode (page 50)  
If the TV is not compatible with the Control for  
HDMI - Easy Setting function, set the Control  
for HDMI function of the system and TV  
manually.  
– System Audio Control (page 50)  
– Volume Limit (page 50)  
Note  
• For details on setting the TV, refer to the operating  
instructions of the TV.  
– Audio Return Channel (page 51)  
– Remote Easy Control (page 51)  
– Language Follow (page 51)  
1
2
3
Make sure that the system and the TV  
are connected with an HDMI cable.  
Turn on the TV and press [/1 to turn on  
the system.  
Control for HDMI is a mutual control function  
standard used by CEC (Consumer Electronics  
Control) for HDMI (High-Definition  
Multimedia Interface).  
Set the Control for HDMI function of the  
system and TV.  
The Control for HDMI function for the  
system and TV is simultaneously set to on.  
The Control for HDMI function will not work  
when you connect this system to a component  
which is not compatible with the Control for  
HDMI function.  
To set the [Control for HDMI]  
function of the system to on/off  
manually  
There are convenient buttons on the system’s  
remote for operating the TV, such as  
THEATER, ONE-TOUCH PLAY, and TV "/1.  
For details, see “Remote control” (page 13) and  
refer to the operating instructions of the TV.  
1
Press HOME.  
The home menu appears on the TV screen.  
2
3
Press C/c to select  
Press X/x to select [System Settings],  
then press  
Press X/x to select [HDMI Settings],  
then press  
[Setup].  
.
ONE-TOUCH TV  
THEATER  
PLAY  
4
BRAVIA Sync  
.
1
2
3
The [HDMI Settings] display appears.  
Note  
5
Press X/x to select [Control for HDMI],  
• Depending on the connected component, the Control  
for HDMI function may not work. Refer to the  
operating instructions supplied with the component.  
then press  
.
US  
49  
       
6
Press X/x to select the setting, then  
press  
.
Enjoying TV sound from the  
speakers in this system  
• [On]: On.  
• [Off]: Off.  
(System Audio Control)  
You can simplify operation to enjoy TV sound  
via this system.  
To use this function, connect the system and the  
TV with an audio cord and an HDMI cable  
(pages 23, 24).  
Turning the system off in sync  
with the TV  
(System Power Off)  
When you turn the TV off by using the POWER  
button on the TV’s remote or TV "/1 on the  
system’s remote, the system turns off  
automatically.  
You can use the System Audio Control function  
as follows:  
• When the system is turned on, TV sound can  
be output from the speakers of the system.  
• When TV sound is output from the speakers of  
the system, you can change the output method  
to the speakers of the TV via the TV menu.  
• When TV sound is output from the speakers of  
the system, you can adjust the volume and turn  
off the sound of the system using the TV  
remote.  
Note  
• This function depends on the settings of your TV. For  
details, refer to the operating instructions of the TV.  
Watching BD/DVD by a single  
button press  
(One-Touch Play)  
Note  
• While the TV is in PAP (picture and picture) mode,  
the System Audio Control function will not work.  
• Depending on the TV, when you adjust the unit's  
volume, the volume level appears on the TV screen.  
In this case, the volume level that appears on the TV  
screen and the unit's front panel display may differ.  
Press ONE-TOUCH PLAY.  
The system and your TV turn on, your TV’s  
input is set to the HDMI input to which the  
system is connected, and the system starts  
playing a disc automatically.  
The System Audio Control function is also  
activated automatically.  
Setting the Maximum Volume  
Level of the System  
Also, when you insert a disc, One-Touch Play is  
enabled. If One-Touch Play does not start (in the  
case of inserting a disc that is not compatible  
with the auto playback function), press  
FUNCTION repeatedly to select “BD/DVD”  
and press N or ONE-TOUCH PLAY.  
(Volume Limit)  
When the System Audio Control function is  
activated, loud sound may be output depending  
on the volume level of the system. You can  
prevent this by limiting the maximum level of  
the volume. For details, see [Volume Limit]  
Using the Theater Mode  
(Theater Mode)  
Press THEATER.  
If your TV is compatible with the Theater Mode,  
you can enjoy optimal image and sound quality  
suited for movies, and the System Audio Control  
function is activated automatically.  
US  
50  
               
1
Press HOME.  
Receiving the digital audio  
signal of the TV  
The home menu appears on the TV screen.  
2
3
Press C/c to select  
Press X/x to select [Audio Settings],  
then press  
Press X/x to select [Auto Calibration],  
then press  
[Setup].  
(Audio Return Channel)  
.
The system can receive the digital audio signal  
of the TV via an HDMI cable when your TV is  
compatible with the Audio Return Channel  
function. You can enjoy TV sound via the  
system by using just one HDMI cable. For  
details, see [Audio Return Channel] (page 60).  
4
.
The confirmation display for [Auto  
Calibration] appears.  
5
Connect the calibration mic to the  
A.CAL MIC jack on the rear panel.  
Operating the system via the  
TV remote  
Set up the calibration mic at ear level using  
a tripod, etc. (not supplied). The front of  
each speaker should face the calibration  
mic, and there should be no obstruction  
between the speakers and the calibration  
mic.  
(Remote Easy Control)  
You can control the basic functions of the  
system via the TV remote when the system’s  
video output is displayed on the TV screen. For  
details, refer to the operating instructions of the  
TV.  
IC  
Changing the language for the  
on-screen display of the TV  
M
L
A
C
.
A
2
C
-A  
M
C
E
(Language Follow)  
When you change the language for the on-screen  
display of the TV, the system’s on-screen  
display language is also changed after turning  
the system off and on.  
Calibration mic  
Calibrating the  
Appropriate Settings  
Automatically  
[Auto Calibration]  
D. C. A. C. (Digital Cinema Auto Calibration)  
can set the appropriate surround sound  
automatically.  
6
Press X/x to select [OK].  
To cancel, select [Cancel].  
Note  
• The system outputs a loud test sound when [Auto  
Calibration] starts. You cannot turn the volume  
down. Give consideration to children and neighbors.  
US  
51  
               
7
Press  
.
[Auto Calibration] starts.  
Setting the Speakers  
[Speaker Settings]  
The system adjusts the speaker settings  
automatically.  
Be quiet during the measurement.  
To obtain the best possible surround sound, set  
connection of the speakers and their distance  
from your listening position. Then use the test  
tone to adjust the level and the balance of the  
speakers to the same level.  
Note  
• Before [Auto Calibration], make sure that the  
surround amplifier turns on and you install the  
surround amplifier in the appropriate location. If  
you install the surround amplifier in an improper  
location, such as another room, proper  
measurement will not be obtained.  
1
Press HOME.  
The home menu appears on the TV screen.  
• When you use the Wireless Surround Speaker  
Kit (WAHT-SBP2, optional) for the surround  
back speakers (page 16), install the speakers in  
appropriate location and turn the surround  
amplifier on. To use the surround back speakers,  
set [Surround Back] in [Speaker Settings] to  
2
3
Press C/c to select  
Press X/x to select [Audio Settings],  
then press  
Press X/x to select [Speaker Settings],  
then press  
[Setup].  
.
4
.
The [Speaker Settings] display appears.  
8
Confirm the conclusions of [Auto  
Calibration].  
5
Press X/x to select the item, then press  
.
The speakers connected to the unit are listed  
as [Yes] on the TV screen.  
Check the following settings.  
Note  
x [Connection]  
• If measurement fails, follow the message then  
retry [Auto Calibration].  
If you do not connect center or surround  
speakers, set the parameters for [Center] and  
[Surround]. Since the front speaker and  
subwoofer settings are fixed, you cannot change  
them.  
• The measurement for [Subwoofer] is always  
[Yes] and [Speaker Settings] returns to the  
default setting when you perform [Auto  
Calibration].  
When you use the Wireless Surround Speaker  
Kit (WAHT-SBP2, optional) for the surround  
back speakers (page 16), set [Surround Back]  
also.  
9
Press X/x to select [OK] or [Cancel],  
then press  
.
x The measurement is OK.  
Disconnect the calibration mic, then select  
[OK]. The result is implemented.  
[Front]  
[Yes]  
x The measurement is not OK.  
Follow the message, then select [OK] to  
retry.  
[Center]  
[Yes]: Normally select this.  
[None]: Select this if no center speaker is used.  
Note  
[Surround]  
• While the Auto Calibration function works:  
– do not turn off the power.  
– do not press any button.  
[Yes]: Normally select this.  
[None]: Select this if no surround speaker is  
used.  
– do not change the volume.  
– do not change the function.  
– do not change the disc.  
[Surround Back]  
[Yes]: Select this if surround back speakers are  
used.  
[None]: Select this if no surround back speakers  
is used.  
– do not insert a disc.  
– do not disconnect the calibration mic.  
US  
52  
           
[Subwoofer]  
Tip  
[Yes]  
• You can change measurement units (feet or meters)  
by pressing the color button (RED).  
x [Distance]  
When you move the speakers, be sure to set the  
parameters of the distance (A) from the  
listening position to the speakers.  
You can set the parameters from 0 to 23 feet (0.0  
to 7.0 meters).  
x [Level]  
You can adjust the sound level of the speakers.  
You can set the parameters from –6.0 dB to +6.0  
dB. Be sure to set [Test Tone] to [On] for easy  
adjustment.  
The speakers in the illustration correspond to the  
following:  
[Front Left/Right] 0.0 dB: Set the front speaker  
level.  
1Center speaker  
2Front left speaker (L)  
3Front right speaker (R)  
4Subwoofer  
5Surround left speaker (L)  
6Surround right speaker (R)  
7Surround back left speaker (L) (optional)  
8Surround back right speaker (R) (optional)  
[Center]* 0.0 dB: Set the center speaker level.  
[Surround Left/Right]* 0.0 dB: Set the surround  
speaker level.  
[Surround Back Left/Right]* 0.0 dB: Set the  
surround back speaker level.  
[Subwoofer] 0.0 dB: Set the subwoofer level.  
* This item appears when you set it to [Yes] in the  
[Connection] setting.  
1
2
3
x [Test Tone]  
The speakers will emit a test tone to adjust  
[Level].  
4
[Off]: The test tone is not emitted from the  
speakers.  
A
[On]: The test tone is emitted from each speaker  
in sequence while adjusting level. When you  
select one of the [Speaker Settings] items, the  
test tone is emitted from each speaker in  
sequence.  
5
6
A
Adjust the sound level as follows.  
7
8
1
2
Set [Test Tone] to [On].  
[Front Left/Right] 10 ft/3.0 m: Set the front  
speaker distance.  
[Center]* 10 ft/3.0 m: Set the center speaker  
distance.  
[Surround Left/Right]* 10 ft/3.0 m: Set the  
surround speaker distance.  
[Surround Back Left/Right]* 10 ft/3.0 m: Set the  
surround back speaker distance.  
[Subwoofer] 10 ft/3.0 m: Set the subwoofer  
distance.  
Press X/x to select [Level], then press  
.
3
4
Press X/x to select the desired speaker  
type, then press  
.
Press C/c to select the left or right  
speaker, then press X/x to adjust the  
level.  
5
6
7
Press  
.
* This item appears when you set it to [Yes] in the  
[Connection] setting.  
Repeat Steps 3 to 5.  
Press RETURN.  
Note  
The system returns to the previous display.  
• Depending on the input stream, [Distance] may not  
be effective.  
8
Press X/x to select [Test Tone], then  
press  
.
US  
53  
     
9
Press X/x to select [Off], then press  
To cancel, press x for more than 5 seconds so  
that “CHILD LOCK” and “OFF” appear in the  
front panel display.  
.
Note  
• The test tone signals are not output from the HDMI  
OUT jack.  
Note  
• When you operate the buttons on the unit while the  
child lock function is on, “CHILD LOCK” appears in  
the front panel display.  
Tip  
• To adjust the volume of all the speakers at one time,  
press VOL +/–.  
Controlling Your TV with  
the Supplied Remote  
By adjusting the remote signal, you can control  
your TV with the supplied remote.  
Using the Sleep Timer  
You can set the system to turn off at a preset  
time, so you can fall asleep listening to music.  
The time can be preset in intervals of 10  
minutes.  
Note  
• When you replace the batteries of the remote, the  
code number may reset itself to the default (SONY)  
setting. Reset the appropriate code number.  
Press SLEEP.  
Each time you press SLEEP, the minutes display  
(the remaining time) changes by 10 minutes.  
When you set the sleep timer, “SLEEP” flashes  
in the front panel display.  
Preparing the remote for  
controlling the TV  
To check the remaining time  
Press SLEEP once.  
Press and hold TV [/1 while entering your  
TV’s manufacturer’s code (see the table)  
using the number buttons. Then release TV  
[/1.  
To change the remaining time  
Press SLEEP repeatedly to select the desired  
time.  
If the setting is unsuccessful, the currently  
registered code is not changed. Re-enter the  
code number.  
Deactivating the Buttons  
on the Unit  
Code numbers of controllable  
TVs  
If more than one code number is listed, try  
entering them one at a time until you find the  
code that works with your TV.  
(Child Lock)  
You can deactivate the buttons on the unit  
(except for "/1) for preventing misoperation,  
such as child mischief (child lock function).  
Manufacturer  
SONY  
Code number  
01 (default)  
Press x on the unit for more than 5  
seconds.  
SAMSUNG  
PANASONIC  
LG  
02, 06  
05  
“CHILD LOCK” and “ON” appear in the front  
panel display.  
The child lock function is activated and the  
buttons on the unit are locked. (You can operate  
the system by using the remote.)  
02  
TOSHIBA  
SHARP  
04  
03  
US  
54  
               
Saving Power in Standby  
Mode  
Check that the following settings are made:  
– [Control for HDMI] in [HDMI Settings] is set  
to [Off] (page 49).  
– [Standby] in [S-AIR Settings] is set to [Off]  
– [Quick Start Mode] is set to [Off] (page 60).  
US  
55  
 
Icon  
Explanation  
Makes the audio settings  
Settings and Adjustments  
according to the type of  
connecting jacks.  
Using the Setup Display  
You can make various adjustments of items such  
Makes detailed settings for BD/  
as picture and sound.  
DVD playback.  
Select  
(Setup) on the home menu when you  
Makes detailed settings for the  
need to change the settings of the system.  
The default settings are underlined.  
Parental Control function.  
Note  
Makes detailed settings for  
Super Audio CD playback.  
• Playback settings stored in the disc take priority over  
the Setup Display settings and not all the functions  
described may work.  
Makes the system-related  
settings.  
1
2
Press HOME.  
The home menu appears on the TV screen.  
Makes detailed settings for  
Internet and network.  
Press C/c to select  
[Setup].  
Re-runs the Easy Setup to make  
the basic settings.  
Resets the system to the factory  
settings.  
3
Press X/x to select the setup category  
[Network Update]  
You can update and improve the functions of the  
icon to change, then press  
.
Example: [Screen Settings]  
system.  
For information about update functions, refer to  
the following website:  
Setup  
TV Type  
Set the screen aspect ratio of your TV.  
Screen Format  
Original  
DVD Aspect Ratio  
Cinema Conversion Mode  
Letter Box  
Auto  
[Screen Settings]  
You can setup the following options.  
x [3D Output Setting]  
[Auto]: Normally select this.  
[Off]: Select this to display all contents in 2D.  
Icon  
Explanation  
Updates the software of the  
system.  
Makes the screen settings  
according to the type of  
connecting jacks.  
x [TV Screen Size Setting for 3D]  
Sets the screen size of your 3D compatible TV.  
US  
56  
                     
[Video]: Automatically sets the lowest  
resolution.  
x [TV Type]  
[16:9]: Select this when connecting to a wide-  
screen TV or a TV with a wide-mode function.  
[4:3]: Select this when connecting to a 4:3  
screen TV without a wide-mode function.  
Note  
• When connecting the HDMI OUT jack and other  
video output jacks at the same time, select  
[Component Video].  
• If no picture appears when setting [HDMI] or  
[Component Video] resolution, try another resolution  
setting.  
x [Screen Format]  
[Original]: Select this when connecting to a TV  
with a wide-mode function. Displays a 4:3  
screen picture in 16:9 aspect ratio even on a  
wide-screen TV.  
[Fixed Aspect Ratio]: Changes the picture size  
to fit the screen size with the original picture  
aspect ratio.  
x [BD/DVD-ROM 1080/24p Output]  
[Auto]: Outputs 1920 × 1080p/24 Hz video  
signals only when connecting a 1080/24p-  
compatible TV using the HDMI OUT jack.  
[Off]: Select this when your TV is not  
compatible with 1080/24p video signals.  
x [DVD Aspect Ratio]  
[Letter Box]: Displays a wide picture with black  
bands on the top and bottom.  
x [YCbCr/RGB (HDMI)]  
[Auto]: Automatically detects the type of  
external device, and switches to the matching  
color setting.  
[YCbCr (4:2:2)]: Outputs YCbCr 4:2:2 video  
signals.  
[YCbCr (4:4:4)]: Outputs YCbCr 4:4:4 video  
signals.  
[RGB]: Select this when connecting to a device  
with an HDCP-compliant DVI jack.  
[Pan & Scan]: Displays a full-height picture on  
the entire screen, with trimmed sides.  
x [HDMI Deep Color Output]  
[Auto]: Normally select this.  
[12bit], [10bit]: Outputs 12bit/10bit video  
signals when the connected TV is compatible  
with Deep Color.  
[Off]: Select this when the picture is unstable or  
colors appear unnatural.  
x [Cinema Conversion Mode]  
[Auto]: Normally select this. The unit  
automatically detects whether the material is  
video-based or film-based, and switches to the  
appropriate conversion method.  
x [Pause Mode] (BD/DVD VIDEO/DVD-R/  
DVD-RW only)  
[Auto]: The picture, including subjects that  
move dynamically, is output with no jitter.  
Normally select this position.  
[Frame]: The picture, including subjects that do  
not move dynamically, is output in high  
resolution.  
[Video]: The conversion method suited for  
video-based material will always be selected  
regardless of the material.  
x [Output Video Format]  
[HDMI]: Normally select [Auto]. Select  
[Original Resolution] to output the resolution  
recorded on the disc. (When the resolution is  
lower than SD resolution, it is scaled up to SD  
resolution.)  
[Component Video]: Select the resolution that  
suits your TV.  
US  
57  
                     
• When the System Audio Control function (page 50)  
is activated, this setting may change automatically.  
[Audio Settings]  
x [Sound Effect]  
x [BD Audio MIX Setting]  
You can set the system’s sound effects (SOUND  
MODE, “D.BASS,” “NIGHT MODE,” and  
“SUR.SETTING”) to on/off.  
[On]: Outputs the audio obtained by mixing the  
interactive audio and secondary audio to the  
primary audio.  
[Off]: Outputs the primary audio only. Select  
this when outputting HD audio signals to an AV  
receiver.  
[On]: Enables all of the system’s sound effects.  
The upper limit of sampling frequency is set to  
48 kHz.  
[Off]: The sound effects are disabled. Select this  
when you do not want to set the upper limit of  
sampling frequency.  
x [Audio DRC]  
You can compress the dynamic range of the  
sound track.  
x [Speaker Settings]  
[Auto]: Performs playback at the dynamic range  
specified by the disc (BD-ROM only).  
[Off]: No compression of dynamic range.  
[On]: The system reproduces the sound track  
with the kind of dynamic range that the  
recording engineer intended.  
To obtain the best possible surround sound, set  
the speakers. For details, see “Setting the  
x [Auto Calibration]  
You can calibrate the appropriate settings  
automatically. For details, see “Calibrating the  
x [Attenuate - AUDIO]  
Distortion may occur when you listen to a  
component connected to the AUDIO (AUDIO  
IN L/R) jacks. You can prevent distortion by  
reducing the input level on the unit.  
[BD/DVD Viewing  
Settings]  
[On]: Attenuates the input level. The output  
level is changed.  
[Off]: Normal input level.  
You can make detailed settings for BD/DVD  
playback.  
x [Audio Output]  
The system cannot output multi-channel sound  
from both the HDMI OUT jack and system’s  
speakers simultaneously.  
x [BD/DVD Menu]  
You can select the default menu language for  
BD-ROMs or DVD VIDEOs.  
When you select [Select Language Code], the  
display for entering the language code appears.  
Enter the code for your language by referring to  
[Speaker]: Outputs multi-channel sound from  
the system’s speakers only.  
[Speaker + HDMI]: Outputs multi-channel  
sound from the system’s speakers and 2-channel  
linear PCM signals from the HDMI OUT jack.  
[HDMI]: Outputs sound from the HDMI OUT  
jack only. Sound format depends on the  
connected component.  
x [Audio]  
You can select the default track language for  
BD-ROMs or DVD VIDEOs.  
When you select [Original], the language given  
priority in the disc is selected.  
Note  
When you select [Select Language Code], the  
display for entering the language code appears.  
• When you set [Audio Output] to [HDMI], the  
SOUND MODE, “D.BASS,” “NIGHT MODE,” and  
“SUR.SETTING” functions are disabled.  
US  
58  
                               
Enter the code for your language by referring to  
x [BD Parental Control]  
Playback of some BD-ROMs can be limited  
according to the age of the users. Scenes may be  
blocked or replaced with different scenes.  
Follow the on-screen instructions and enter your  
four-digit password.  
x [Subtitle]  
You can select the default subtitle language for  
BD-ROMs or DVD VIDEOs.  
When you select [Select Language Code], the  
display for entering the language code appears.  
Enter the code for your language by referring to  
x [DVD Parental Control]  
Playback of some DVD VIDEOs can be limited  
according to a predetermined level such as the  
age of the users. Scenes may be blocked or  
replaced with different scenes. Follow the on-  
screen instructions and enter your four-digit  
password.  
x [BD Hybrid Disc Playback Layer]  
[BD]: Plays BD layer.  
[DVD/CD]: Plays DVD or CD layer.  
x [BD Internet Connection]  
[Allow]: Normally select this.  
[Do not allow]: Prohibits Internet connection.  
x [Internet Video Parental Control]  
Playback of some Internet videos can be limited  
according to the age of the users. Scenes may be  
blocked or replaced with different scenes.  
Follow the on-screen instructions and enter your  
four-digit password.  
x [BD Data Jack Selection]  
[Internal memory]: Selects the internal memory  
to store BD data.  
[USB device (front)]: Selects the  
on the front panel to store BD data.  
[USB device (rear)]: Selects the  
on the rear panel to store BD data.  
(USB) port  
x [Internet Video Unrated]  
[Allow]: Allows the playback of unrated  
Internet videos.  
[Block]: Blocks the playback of unrated Internet  
videos.  
(USB) port  
[Parental Control  
Settings]  
[Music Settings]  
You can make detailed settings for Super Audio  
CD playback.  
x [Password]  
Set or change the password for the Parental  
Control function. A password allows you to set  
a restriction on BD-ROM, DVD VIDEO, or  
Internet video playback. If necessary, you can  
differentiate the restriction levels for BD-ROMs  
and DVD VIDEOs.  
x [Super Audio CD Playback Layer]  
[Super Audio CD]: Plays the Super Audio CD  
layer.  
[CD]: Plays the CD layer.  
x [Super Audio CD Playback Channel]  
[DSD 2ch]: Plays the 2ch area.  
[DSD Multi]: Plays the multi-channel area.  
x [Parental Control Area Code]  
Playback of some BD-ROMs or DVD VIDEOs  
can be limited according to the geographic area.  
Scenes may be blocked or replaced with  
different scenes. Follow the on-screen  
instructions and enter your four-digit password.  
US  
59  
                                 
[Off]: Off.  
[System Settings]  
You can make the system-related settings.  
Note  
• This function is available only when [Control for  
HDMI] is set to [On].  
[Volume Limit]  
x [OSD]  
When the System Audio Control (page 50) is  
activated, loud sound may be output depending  
on the volume level of the system. You can  
prevent this by limiting the maximum level of  
the volume when the System Audio Control  
function activates.  
You can select your language for the system on-  
screen displays.  
x [S-AIR Settings]  
You can set up the S-AIR settings. For details,  
[Level3]: Maximum volume level is set to 10.  
[Level2]: Maximum volume level is set to 15.  
[Level1]: Maximum volume level is set to 20.  
[Off]: Off.  
[ID]: You can set the ID of the system.  
[Pairing]: You can pair the system and S-AIR  
sub unit, such as a surround amplifier or S-AIR  
receiver.  
[RF Change]: If wireless transmission is  
unstable, set this function.  
[Mode]: You can enjoy the system’s sound in  
another room.  
[Standby]: You can enjoy the S-AIR receiver  
while the unit is in standby mode.  
Note  
• This function is available only when [Control for  
HDMI] is set to [On].  
x [Quick Start Mode]  
[On]: Shortens the startup time from standby  
mode. You can operate the system quickly after  
turning it on.  
x [Dimmer]  
[Bright]: Bright lighting.  
[Dark]: Low lighting.  
[Off]: The default setting.  
x [Auto Standby]  
[On]: Turns on the [Auto Standby] function.  
When you do not operate the system for about  
30 minutes, the system enters standby mode  
automatically.  
x [HDMI Settings]  
By connecting Sony components that are  
compatible with the Control for HDMI function  
with an HDMI cable, operation is simplified.  
[Off]: Turns off the function.  
x [Auto Display]  
[On]: Automatically displays information on the  
screen when changing the viewing titles, picture  
modes, audio signals, etc.  
[Control for HDMI]  
You can set the [Control for HDMI] function to  
on/off.  
[Off]: Displays information only when you  
press DISPLAY.  
[On]: On. You can operate mutually between  
components that are connected with an HDMI  
cable.  
[Off]: Off.  
x [Screen Saver]  
[On]: Turns on the screen saver function.  
[Off]: Off.  
[Audio Return Channel]  
This function is available when you connect the  
system and TV that is compatible with the Audio  
Return Channel function.  
[Auto]: The system can receive the digital audio  
signal of the TV automatically via an HDMI  
cable.  
x [Software Update Notification]  
[On]: Sets the system to inform you of newer  
software version information (page 56).  
[Off]: Off.  
US  
60  
                           
x [Gracenote Settings]  
[Network Settings]  
You can make detailed settings for Internet and  
(Except for BDV-E370 (U.S. models))  
[Auto]: Automatically downloads disc  
information when you stop playback of the disc.  
To download, the system must be connected to  
the network.  
[Manual]: Downloads disc information when  
you select [Playback History List] or  
[Information Display] in the options menu.  
network.  
x [Internet Settings]  
Connect the system to the network beforehand.  
x [DivX® VOD]  
[View Network Status]: Displays the current  
network status.  
[Wired Setup]: Select this when you connect to  
a broadband router directly.  
[USB Wireless Setup]: Select this when you use  
a USB Wireless LAN Adapter.  
(Except for U.S. models, BDV-E470)  
You can display the registration or  
deregistration code for this system, or deregister  
this system after registration.  
When the registration is disabled  
[Registration Code]: The registration code is  
displayed.  
For more information, go to  
[Deregistration Code]: The deregistration code  
is displayed. (This item can be selected only  
after the registration code is displayed.)  
x [Network Connection Diagnostics]  
You can run the network diagnostic to check if  
the network connection has been made properly.  
When the registration is enabled  
Press C/c to select [OK] or [Cancel], then  
x [Connection Server Settings]  
Sets whether or not to display the connected  
DLNA server.  
press  
.
[OK]: The device is deregistered and the  
deregistration code is displayed.  
[Cancel]: The system returns to the previous  
display.  
x [Renderer Options]  
[Auto Access Permission]: Sets whether or not  
to allow automatic access from newly detected  
DLNA controller.  
For more information, go to  
[Smart Select]: Allows a Sony DLNA controller  
to find the system as the target component to  
operate by using the infrared ray. You can set  
this function to on or off.  
[Renderer Name]: Displays the system’s name  
as it is listed on other DLNA devices on the  
network.  
x [System Information]  
You can display the system’s software version  
information and the MAC address.  
x [Renderer Access Control]  
Sets whether or not to accept commands from  
DLNA controllers.  
US  
61  
                           
x [Party Auto Start]  
[On]: Starts a party or joins an existing party at  
the request of a networked device compatible  
with the PARTY STREAMING function.  
[Off]: Off.  
x [BD Remote Device Registration]  
Registers your “BD remote” device.  
x [Registered BD Remote Devices]  
Displays a list of your registered “BD remote”  
devices.  
[Easy Setup]  
Re-runs the Easy Setup to make the basic  
settings. Follow the on-screen instructions.  
[Resetting]  
x [Reset to Factory Default Settings]  
You can reset the system settings to the factory  
default by selecting the group of settings. All the  
settings within the group will be reset.  
x [Initialize Personal Information]  
You can erase your personal information stored  
in the system.  
US  
62  
                   
• Do not place the system in a place where medical  
equipment is in use. It may cause a malfunction of  
medical equipment (BDV-E570/BDV-T57 only).  
• If you use a pacemaker or other medical device,  
consult your physician or the manufacturer of your  
medical device before using the wireless LAN  
function (BDV-E570/BDV-T57 only).  
Additional Information  
Precautions  
On safety  
• To prevent fire or shock hazard, do not place objects  
filled with liquids, such as vases, on the system, or  
place the system near water, such as near a bathtub or  
shower room. Should any solid object or liquid fall  
into the cabinet, unplug the system and have it  
checked by qualified personnel before operating it  
any further.  
On operation  
• If the system is brought directly from a cold to a warm  
location, or is placed in a very damp room, moisture  
may condense on the lenses inside the unit. Should  
this occur, the system may not operate properly. In  
this case, remove the disc and leave the system turned  
on for about half an hour until the moisture  
evaporates.  
• Do not touch the AC power cord (mains lead) with  
wet hands. Doing so may cause an electric shock.  
• When you move the system, take out any disc. If you  
do not, the disc may be damaged.  
On power sources  
• If anything falls into the cabinet, unplug the unit and  
have it checked by qualified personnel before  
operating it any further.  
• Unplug the unit from the wall outlet (mains) if you do  
not intend to use it for an extended period of time. To  
disconnect the cord, pull it out by the plug, never by  
the cord.  
On adjusting volume  
• Do not turn up the volume while listening to a section  
with very low level inputs or no audio signals. If you  
do, the speakers may be damaged when a peak level  
section is suddenly played.  
On placement  
• Place the system in a location with adequate  
ventilation to prevent heat build-up in the system.  
• At high volume, over long periods of time, the cabinet  
becomes hot to the touch. This is not a malfunction.  
However, touching the cabinet should be avoided. Do  
not place the system in a confined space where  
ventilation is poor as this may cause overheating.  
• Do not block the ventilation slots by putting anything  
on the system. The system is equipped with a high  
power amplifier. If the ventilation slots are blocked,  
the system can overheat and malfunction.  
• Do not place the system on surfaces (rugs, blankets,  
etc.) or near materials (curtains, draperies) that may  
block the ventilation slots.  
On cleaning  
• Clean the cabinet, panel, and controls with a soft cloth  
slightly moistened with a mild detergent solution. Do  
not use any type of abrasive pad, scouring powder or  
solvent such as alcohol or benzine.  
If you have any questions or problems concerning  
your system, please consult your nearest Sony dealer.  
On cleaning discs, disc/lens  
cleaners  
• Do not use cleaning discs or disc/lens cleaners  
(including wet or spray types). These may cause  
the apparatus to malfunction.  
• Do not install the system in a confined space, such as  
a bookshelf or similar unit.  
• Do not install the system near heat sources such as  
radiators, air ducts, or in a place subject to direct  
sunlight, excessive dust, mechanical vibration, or  
shock.  
On replacement of parts  
• In the events that this system is repaired, repaired  
parts may be collected for reuse or recycling  
purposes.  
• Do not install the system in an inclined position. It is  
designed to be operated in a horizontal position only.  
• Keep the system and discs away from components  
with strong magnets, such as microwave ovens, or  
large loudspeakers.  
On your TV’s color  
• If the speakers should cause the TV screen to have  
color irregularity, turn off the TV then turn it on after  
15 to 30 minutes. If color irregularity should persist,  
place the speakers further away from the TV set.  
• Do not place heavy objects on the system.  
• Do not place metal objects in front of the front panel.  
They may limit reception of radio waves (BDV-  
E570/BDV-T57 only).  
US  
63  
   
IMPORTANT NOTICE  
Caution: This system is capable of holding a still  
Notes about the Discs  
On handling discs  
• To keep the disc clean, handle the disc by its  
edge. Do not touch the surface.  
video image or on-screen display image on your  
television screen indefinitely. If you leave the still  
video image or on-screen display image displayed  
on your TV for an extended period of time you risk  
permanent damage to your television screen.  
Projection televisions are especially susceptible to  
this.  
• Do not stick paper or tape on the disc.  
On moving the system  
• Before moving the system, make sure that there is no  
disc inserted, and remove the AC power cord (mains  
lead) from the wall outlet (mains).  
• Do not expose the disc to direct sunlight or  
heat sources such as hot air ducts, or leave it in  
a car parked in direct sunlight as the  
temperature may rise considerably inside the  
car.  
• After playing, store the disc in its case.  
On cleaning  
• Before playing, clean the disc with a cleaning  
cloth.  
Wipe the disc from the center out.  
• Do not use solvents such as benzine, thinner,  
commercially available cleaners, or anti-static  
spray intended for vinyl LPs.  
This system can only play a standard circular  
disc. Using neither standard nor circular discs  
(e.g., card, heart, or star shape) may cause a  
malfunction.  
Do not use a disc that has a commercially  
available accessory attached, such as a label or  
ring.  
US  
64  
 
Troubleshooting  
If you experience any of the following difficulties while using the system, use this troubleshooting  
guide to help remedy the problem before requesting repairs. Should any problem persist, consult your  
nearest Sony dealer.  
Note that if service personnel changes some parts during repair, these parts may be retained.  
In the event of a problem with the S-AIR function, have a Sony dealer check the entire system together  
(S-AIR main unit and sub unit).  
Power  
Symptom  
Problems and solutions  
The power is not turned on.  
“PROTECTOR” and “PUSH  
• Check that the AC power cord (mains lead) is connected securely.  
Press "/1 to turn off the system, and check the following items after  
POWER” appear alternately in “STANDBY” disappears.  
the front panel display.  
• Are the + and – speaker cords short-circuited?  
• Are you using only the specified speakers?  
• Is anything blocking the ventilation holes of the system?  
• After checking the above items and fixing any problems, turn on the system. If  
the cause of the problem cannot be found even after checking all the above  
items, consult your nearest Sony dealer.  
General  
Symptom  
Problems and solutions  
The remote does not function.  
• The distance between the remote and the unit is too far.  
• The batteries in the remote are weak.  
• When you cannot perform menu operations via the front panel display, press  
HOME on the remote.  
The system does not work  
normally.  
• Disconnect the AC power cord (mains lead) from the wall outlet (mains), then  
reconnect after several minutes.  
Picture  
Symptom  
Problems and solutions  
There is no picture.  
• Check the video connection (page 23).  
• The unit is not connected to the correct TV input jack (page 23).  
• The video input on the TV is not set so that you can view pictures from the  
system.  
• Check the output method on your system (page 23).  
• The unit is connected to an input device that is not HDCP (High-bandwidth  
Digital Content Protection) compliant (“HDMI” on the front panel does not  
light up) (page 23).  
• When playing a double-layer DVD, the video and audio may be momentarily  
interrupted at the point where the layers switch.  
No picture appears when the  
• Press and hold N and VOLUME – on the unit for more than 5 seconds to reset  
video output resolution selected the video output resolution to the lowest resolution.  
in [Output Video Format] is  
incorrect.  
US  
65  
 
Symptom  
Problems and solutions  
Video signals are only output  
• Set [Output Video Format] in [Screen Settings] to [Component Video]  
from the HDMI OUT jack when (page 57).  
connecting the HDMI OUT jack  
and other video output jacks at  
the same time.  
The dark area of the picture is too • Set [Picture Quality Mode] to [Standard] (default) (page 37).  
dark/the bright area is too bright  
or unnatural.  
The picture is not output  
correctly.  
• Check the [Output Video Format] settings in [Screen Settings] (page 57).  
• If the analog and digital signals are output at the same time, set [BD/DVD-  
ROM 1080/24p Output] in [Screen Settings] to [Off] (page 57).  
• For BD-ROMs, check the [BD/DVD-ROM 1080/24p Output] settings in  
[Screen Settings] (page 57).  
Picture noise appears.  
• The disc is dirty or flawed.  
• If the picture output from your system goes through your VCR to get to your  
TV, the copy-protection signal applied to some BD/DVD programs could affect  
picture quality. If you still experience problems even when you connect your  
unit directly to your TV, try connecting your unit to the other input jacks.  
Even though you set the aspect • The aspect ratio on the disc is fixed.  
ratio in [TV Type] of [Screen  
Settings], the picture does not fill  
the TV screen.  
Color irregularity occurs on the • If the speakers are used with a CRT-based TV or projector, install the speakers  
TV screen.  
at least 1.0 ft (0.3 meters) from the TV set.  
• If the color irregularity persists, turn off the TV set once, then turn it on after 15  
to 30 minutes.  
• Make sure that no magnetic object (magnetic latch on a TV stand, health care  
device, toy, etc.) is placed near the speakers.  
Sound  
Symptom  
Problems and solutions  
There is no sound.  
• The speaker cord is not connected securely.  
• Check the speaker settings (page 52).  
• Fast forward or fast reverse is performed. Press N to return to normal play  
mode.  
• Slow forward or freeze frame is performed. Press N to return to normal play  
mode.  
No sound is output from the  
HDMI OUT jack.  
• Set [Audio Output] to [HDMI] (page 58).  
The left and right sounds are  
unbalanced or reversed.  
• Check that the speakers and components are connected correctly and securely.  
• Check the speaker connections and settings (pages 22, 52).  
There is no sound from the  
subwoofer.  
US  
66  
Symptom  
Problems and solutions  
There is no digital sound from  
• Set [Control for HDMI] in [HDMI Settings] of [System Settings] to [On]  
the HDMI OUT jack when using (page 60). Also, set [Audio Return Channel] in [HDMI Settings] of [System  
the Audio Return Channel  
function.  
Settings] to [Auto] (page 60).  
• Make sure that your TV is compatible with the Audio Return Channel function.  
• Make sure that an HDMI cable is connected to a jack on your TV that is  
compatible with the Audio Return Channel function.  
• The sampling frequency of the input stream is more than 48 kHz.  
The system does not output  
• Set [Audio Return Channel] in [HDMI Settings] of [System Settings] to [Off]  
sound correctly when connected (page 51).  
to a set-top box.  
Severe hum or noise is heard.  
• Check that the connecting cords are away from a transformer or motor, and at  
least 10 feet (3 meters) away from your TV set or a fluorescent light.  
• Move your TV away from the audio components.  
• Clean the disc.  
The sound loses stereo effect  
when you play a CD.  
• Select stereo sound by pressing AUDIO (page 39).  
The surround effect is difficult to • Check the surround setting (page 30).  
hear when you are playing a  
sound track of Dolby Digital,  
DTS, or MPEG audio.  
• Check the speaker connections and settings (pages 22, 52).  
• Depending on the BD/DVD, the output signal may not be the entire 5.1 channel.  
It may be monaural or stereo even if the sound track is recorded in Dolby  
Digital or MPEG audio format.  
The sound comes from the center • Depending on the disc, the sound may come from the center speaker only.  
speaker only.  
No sound is heard from the  
center speaker.  
• Check the speaker connections and settings (pages 22, 52).  
• Check the surround setting (page 30).  
• Depending on the source, the effect of the center speaker may be less  
noticeable.  
• A 2 channel source is being played.  
No sound or only a very low-  
level sound is heard from the  
surround speakers.  
• Check the speaker connections and settings (pages 22, 52).  
• Check the surround setting (page 30).  
• Depending on the source, the effect of the surround speakers may be less  
noticeable.  
• A 2 channel source is being played.  
The beginning of the sound is cut • Set the sound mode to “MOVIE” or “MUSIC” (page 39).  
off.  
• Select “A.F.D. STD” for “SUR.SETTING” (page 30).  
The sound effects are disabled. • The effects of SOUND MODE, “D.BASS,” “NIGHT MODE,” and  
“SUR.SETTING” may be disabled depending on the input stream (page 58).  
Distortion occurs in the sound of • Reduce the input level for the connected component by setting [Attenuate -  
a connected component.  
Operation  
Symptom  
Problems and solutions  
Radio stations cannot be tuned • Check that the antenna (aerial) is connected securely. Adjust the antenna  
in.  
(aerial) or connect an external antenna (aerial) if necessary.  
• The signal strength of the stations is too weak (when tuning in with automatic  
tuning). Use direct tuning.  
US  
67  
Symptom  
Problems and solutions  
The disc does not play.  
• You are attempting to play a disc with a format that cannot be played back by  
this system (page 72).  
• The region code on the BD/DVD does not match the system.  
• Moisture has condensed inside the unit and may cause damage to the lenses.  
Remove the disc and leave the unit turned on for about half an hour.  
• The system cannot play a recorded disc that is not correctly finalized (page 72).  
File names are not displayed  
correctly.  
• The system can only display ISO 8859-1-compliant character formats. Other  
character formats may be displayed differently.  
• Depending on the writing software used, the input characters may be displayed  
differently.  
A disc does not start playing  
from the beginning.  
• Resume play has been selected. Press OPTIONS and select [Play from  
beginning], then press  
• The title or BD/DVD menu automatically appears on the TV screen.  
Playback does not start from the • The resume point may be cleared from memory depending on the disc when  
.
resume point where you last  
stopped playing.  
– you open the disc tray.  
– you disconnect the USB device.  
– you play other content.  
– you turn off the unit.  
The system starts playing the  
disc automatically.  
• The BD/DVD features an auto playback function.  
Playback stops automatically.  
• Some discs may contain an auto pause signal. While playing such a disc, the  
system stops playback at the auto pause signal.  
You cannot perform some  
• Depending on the disc, you may not be able to perform some of the operations.  
functions such as stop or search. Refer to the operating instructions supplied with the disc.  
Messages do not appear on the • In the Setup Display, select the desired language for the on-screen display in  
TV screen in the language you  
want.  
The language for the soundtrack/ • Try using the BD’s or DVD’s menu.  
subtitle or angles cannot be  
changed.  
• Multi-lingual tracks/subtitles or multi-angles are not recorded on the BD or  
DVD being played.  
• The BD or DVD prohibits the changing of the language for the sound track/  
subtitle or angles.  
The disc tray does not open and • Try the following: 1 Press and hold N and Z on the unit for more than 5  
you cannot remove the disc even seconds to open the disc tray. 2 Remove the disc. 3 Disconnect the AC power  
after you press Z.  
cord (mains lead) from the wall outlet (mains), then reconnect after several  
minutes.  
A disc cannot be ejected and  
“LOCKED” appears in the front  
panel display.  
• Contact your Sony dealer or local authorized Sony service facility.  
US  
68  
Symptom  
Problems and solutions  
The Control for HDMI function • Set [Control for HDMI] in [HDMI Settings] of [System Settings] to [On]  
does not work.  
• Make sure that the connected component is compatible with the [Control for  
HDMI] function.  
• Check the connected component’s setting for the Control for HDMI function.  
Refer to the operating instructions supplied with the component.  
• If you change the HDMI connection, connect and disconnect the AC power  
cord (mains lead), or have a power failure, set [Control for HDMI] in [HDMI  
Settings] of [System Settings] to [Off], then set [Control for HDMI] to [On]  
No sound is output from the  
system and TV while using the  
System Audio Control function.  
• Make sure that the connected TV is compatible with the System Audio Control  
function.  
Bonus contents or other data that • Try the following: 1 Remove the disc. 2 Turn the system off. 3 Remove and  
are contained in a BD-ROM  
cannot be played.  
reconnect the USB device (page 33). 4 Turn the system on. 5 Insert the BD-  
ROM with BONUSVIEW/BD-LIVE.  
The unit does not work and  
“CHILD LOCK” appears in the  
front panel display when you  
press any button on the unit.  
• Set the child lock function to off (page 54).  
The system menu does not work. • Press HOME on the remote.  
USB device  
Symptom  
Problems and solutions  
The USB device is not  
recognized.  
• Try the following: 1 Turn the system off. 2 Remove and reconnect the USB  
device. 3 Turn the system on.  
• Make sure that the USB device is securely connected to the  
• Check if the USB device or a cable is damaged.  
• Check if the USB device is on.  
(USB) port.  
• If the USB device is connected via a USB hub, disconnect it and connect the  
USB device directly to the unit.  
US  
69  
S-AIR  
Symptom  
Problems and solutions  
There is no sound from the  
S-AIR sub unit, noise is heard  
from the S-AIR sub unit, or  
sound from the S-AIR sub unit  
skips.  
• If you use another S-AIR main unit, place it more than 25 feet (8 meters) away  
from the unit.  
• Place the S-AIR main unit and S-AIR sub unit closer together.  
• Avoid use of equipment that generates electromagnetic energy, such as a  
microwave oven.  
• Place the S-AIR main unit and S-AIR sub unit away from other wireless  
products.  
• Change the S-AIR ID settings of the S-AIR main unit and S-AIR sub unit.  
• Turn off the system and S-AIR sub unit, then turn them on.  
BRAVIA Internet Video  
Symptom  
Problems and solutions  
The picture/sound is poor/certain • Picture/sound quality may be poor depending on Internet content providers.  
programs display with a loss of  
detail, especially during fast-  
motion or dark scenes.  
• Picture/sound quality may be improved by changing the connection speed.  
Sony recommends a connection speed of at least 2.5 Mbps for standard-  
definition video and 10 Mbps for high-definition video.  
• Not all videos contain sound.  
The picture is small.  
• Press X to zoom in.  
Network connection  
Symptom  
Problems and solutions  
The system cannot connect to the • Check the network connection (page 27) and the network settings (page 61).  
network.  
You cannot connect your PC to • The wireless settings of the router may change automatically if you use the Wi-  
the Internet after [Wi-Fi  
Protected Setup (WPS)] is  
performed.  
Fi Protected Setup function before adjusting the settings of the router. In this  
case, change the wireless settings of your PC accordingly.  
You cannot connect the system • Check if the wireless LAN router is on.  
to your wireless LAN router.  
• Depending on the usage environment, including the wall material, radio wave  
reception conditions, or obstacles between the system and the wireless LAN  
router, the possible communication distance may be shortened. Move the  
system and the wireless LAN router closer to each other.  
• Devices that use a 2.4 GHz frequency band, such as a microwave, Bluetooth, or  
digital cordless device, may interrupt the communication. Move the unit away  
from such devices, or turn off such devices.  
The desired wireless router is not • Press RETURN to return to the previous screen, and try [Scan] again. If the  
detected even if [Scan] is  
performed.  
desired wireless router is still not detected, press RETURN to select [Manual  
registration].  
The message [A new software  
version has been found on the  
network. Perform update under  
“Network Update.”] appears on  
the screen when turning the  
system on.  
• See [Network Update] (page 56) to update the system to a newer software  
version.  
US  
70  
USB Wireless LAN Adapter  
(BDV-E570 and BDV-T57 only)  
Symptom  
Problems and solutions  
The system cannot connect to the • The distance between the unit and the wireless LAN router is too far (page 27).  
network or the network  
connection is unstable.  
• Change the USB Wireless LAN Adapter position.  
Other  
Symptom  
Problems and solutions  
“Exxxx” appears in the front  
panel display.  
• Contact your nearest Sony dealer or local authorized Sony service facility and  
give the error code.  
appears without any  
• Contact your nearest Sony dealer or local authorized Sony service facility.  
messages on the entire screen.  
US  
71  
Note on playback operations of a  
BD/DVD  
Some playback operations of a BD/DVD may be  
intentionally set by software producers. Since  
this system plays a BD/DVD according to the  
disc contents the software producers designed,  
some playback features may not be available.  
Playable Discs  
1)  
Blu-ray Disc  
BD-ROM  
2)  
BD-R/BD-RE  
DVD-ROM  
3)  
DVD  
DVD-R/DVD-RW  
DVD+R/DVD+RW  
Note about double-layer BDs/  
DVDs  
The playback picture and sound may be  
3)  
CD  
CD-DA (Music CD)  
CD-ROM  
momentarily interrupted when the layers switch.  
CD-R/CD-RW  
Super Audio CD  
Region code (BD-ROM/DVD  
VIDEO only)  
1)Since the Blu-ray Disc specifications are new and  
evolving, some discs may not be playable depending  
on the disc type and the version. Also, the audio  
output differs depending on the source, connected  
output jack, and selected audio settings.  
2)BD-RE: Ver.2.1  
Your system has a region code printed on the  
rear of the unit and will only play a BD-ROM/  
DVD VIDEO (playback only) labeled with  
ALL  
identical region codes or  
.
BD-R: Ver.1.1, 1.2, 1.3 including organic pigment  
type BD-R (LTH type)  
BD-Rs recorded on a PC cannot be played if  
postscripts are recordable.  
3)A CD or DVD disc will not play if it has not been  
correctly finalized. For more information, refer to the  
operating instructions supplied with the recording  
device.  
Discs that cannot be played  
• BDs with cartridge  
• DVD-RAMs  
• HD DVDs  
• DVD Audio discs  
• PHOTO CDs  
• Data part of CD-Extras  
• VCDs/Super VCDs  
• Audio material side on DualDiscs  
• A disc recorded in a color system other than  
NTSC, such as PAL (this system conforms to  
the NTSC color system).  
Notes on discs  
This product is designed to playback discs that  
conform to the Compact Disc (CD) standard.  
DualDiscs and some music discs encoded with  
copyright protection technologies do not  
conform to the Compact Disc (CD) standard.  
Therefore, these discs may not be compatible  
with this product.  
US  
72  
     
6)The system plays SD resolution only via the DLNA  
function.  
Playable Types of Files  
Video7)  
7)The system does not play these files via the renderer  
function.  
Note  
File format  
Extensions  
• Some files may not play depending on the file format,  
the file encoding, the recording condition, or DLNA  
server condition.  
1)5)  
MPEG-1 Video/PS  
“.mpg,” “.mpeg,” “.m2ts,”  
“.mts”  
MPEG-2 Video/PS,  
1)6)  
• Some files edited on a PC may not play.  
• The system can recognize the following files or  
folders in BDs, DVDs, CDs and USB devices:  
– up to folders in the 5th tree  
TS  
2)  
DivX  
“.avi,” “.divx”  
1)5)  
MPEG4/AVC  
“.mkv,” “.mp4,” “.m4v,”  
“.m2ts,” “.mts”  
– up to 500 files in a single tree  
1)5)  
WMV9  
“.wmv,” “.asf”  
3)5)  
• The system can recognize the following files or  
folders stored in the DLNA server:  
AVCHD  
– up to folders in the 20th tree  
Music  
– up to 999 files in a single tree  
• Some USB devices may not work with this system.  
• The system can recognize Mass Storage Class (MSC)  
devices (such as flash memory or an HDD) that are  
FAT-compatible and non-partitioned, Still Image  
Capture Devices (SICDs), and 101-key keyboards  
File format  
Extensions  
MP3 (MPEG-1 Audio  
Layer III)  
“.mp3”  
1)4)5)  
AAC  
“.m4a”  
“.wma”  
“.wav”  
1)4)  
WMA9 Standard  
(front  
(USB) port only).  
LPCM  
• To avoid data corruption or damage to USB memory  
or other devices, turn the system off before  
connecting or removing USB memory or other  
devices.  
Photo7)  
File format  
Extensions  
• The system may not play high bit rate video files from  
a DATA CD smoothly. It is recommended to play  
high bit rate video files using a DATA DVD.  
JPEG  
“.jpg,” “.jpeg,” “.jpe”  
1)The system does not play files encoded with DRM.  
2) Canadian models only (Except for BDV-E470)  
®
ABOUT DIVX VIDEO: DivX is a digital video  
format created by DivX, Inc. This is an official DivX  
Certified device that plays DivX video. Visit  
tools to convert your files into DivX video.  
ABOUT DIVX VIDEO-ON-DEMAND: This DivX  
®
Certified device must be registered in order to play  
DivX Video-on-Demand (VOD) content. To  
generate the registration code, locate the DivX VOD  
section in the device setup menu. Go to  
vod.divx.com with this code to complete the  
registration process and learn more about DivX  
VOD.  
3)The system plays AVCHD-format files that are  
recorded via a digital video camera, etc. To watch  
AVCHD-format files, the disc with AVCHD-format  
files on it must be finalized.  
4)The system does not play files encoded with  
Lossless, etc.  
5)The system does not play these files via the DLNA  
function.  
US  
73  
   
Supported Audio Formats  
Audio formats supported by this system are as follows.  
Format  
LPCM 2ch  
LPCM 5.1ch,  
LPCM 7.1ch  
Dolby Digital Dolby  
TrueHD,  
DTS  
DTS-ES  
Discrete 6.1,  
DTS-ES  
Matrix 6.1,  
DTS96/24  
DTS-HD  
High  
Resolution  
Audio  
DTS-HD  
Master  
Audio  
Function  
Dolby Digital  
Plus  
“BD/DVD”  
a
a
a
a
a
a
a
a
a
a
a
“SAT/CABLE”  
“TV”  
(DIGITAL IN)  
a: Supported format.  
–: Unsupported format.  
Video Output Resolution  
Output resolution differs depending on the [Output Video Format] setting in [Screen Settings]  
When [Output Video Format] is set to  
[HDMI]  
When [Output Video Format] is set to  
[Component Video]  
Resolution  
setting  
COMPONENT  
COMPONENT  
VIDEO OUT  
jack  
HDMI OUT  
VIDEO OUT  
jack  
HDMI OUT  
VIDEO OUT  
jacks  
VIDEO OUT  
jacks  
jack  
jack  
480i  
480i  
480i  
480i  
480i  
480i  
480i  
480p  
480i  
480p  
720p  
1080i  
1080p  
480i  
480i  
480i  
480p  
480i  
480p  
720p  
1080i  
480p  
720p  
1080i  
1080p  
720p*  
1080i*  
1080i*  
480i  
720p*  
1080i*  
480i  
unselectable  
unselectable unselectable  
* Protected contents on DVDs are output at 480p resolution.  
When [Output Video Format] is set to [Video]  
480i video signals are output from the VIDEO OUT or COMPONENT VIDEO OUT jack, and 480p  
video signals are output from the HDMI OUT jack.  
US  
74  
   
camera, and digital video  
camera)  
500 mA  
Specifications  
Amplifier Section  
Maximum current:  
LAN Section  
LAN (100) terminal  
100BASE-TX Terminal  
U.S. models:  
POWER OUTPUT AND TOTAL HARMONIC  
DISTORTION:  
(FTC)  
Tuner Section  
System  
PLL quartz-locked digital  
synthesizer  
Front L + Front R:  
With 3 ohms loads, both  
channels driven, from 180  
- 20,000 Hz; rated 60 watts  
per channel minimum  
FM tuner section  
Tuning range  
North American models: 87.5 MHz - 108.0 MHz  
(100 kHz step)  
RMS power, with no more  
than 1% total harmonic  
distortion from 250 milli  
watts to rated output.  
Other models:  
87.5 MHz - 108.0 MHz  
(50 kHz step)  
FM wire antenna (aerial)  
Antenna (aerial)  
Antenna (aerial) terminals 75 ohms, unbalanced  
Other models:  
POWER OUTPUT (rated)  
Front L/Front R:  
Intermediate frequency  
10.7 MHz  
Speakers  
108 W + 108 W (at 3 ohms,  
1 kHz, 1% THD)  
Front/Surround (SS-TSB101) for BDV-E570/  
BDV-E470/BDV-E370/BDV-T57/BDV-T37  
BDV-E370/BDV-T37:  
POWER OUTPUT (reference)  
Front L/Front R/Center/Surround L/Surround R:  
142 W (per channel at 3  
Surround (SS-TSB101) for BDV-E870  
Speaker system  
Speaker unit  
Full range Bass reflex  
55 mm × 80 mm (2 1/4 in ×  
3 1/4 in) cone type  
3 ohms  
ohms, 1 kHz)  
Subwoofer:  
140 W (at 3 ohms, 80 Hz)  
Rated impedance  
BDV-E870/BDV-E570/BDV-E470/BDV-T57:  
POWER OUTPUT (reference)  
Front L/Front R/Center/Surround L/Surround R:  
167 W (per channel at 3  
Dimensions (approx.)  
75 mm × 225 mm × 71 mm  
(3 in × 8 7/8 in × 2 7/8 in)  
(w/h/d)  
Mass (approx.)  
0.45 kg (1 lb)  
ohms, 1 kHz)  
Subwoofer:  
165 W (at 3 ohms, 80 Hz)  
Sensitivity: 450/250 mV  
Front (SS-TSB104) for BDV-E870  
Inputs (Analog)  
AUDIO (AUDIO IN)  
Inputs (Digital)  
SAT/CABLE (COAXIAL), TV (OPTICAL)  
Supported formats: LPCM  
Speaker system  
Speaker unit  
Full range Bass reflex  
55 mm × 80 mm (2 1/4 in ×  
3 1/4 in) cone type  
3 ohms  
Rated impedance  
Dimensions (approx.)  
75 mm × 610 mm × 70 mm  
(3 in × 24 1/8 in × 2 7/8 in)  
(w/h/d) (wall-mounted  
part)  
2CH (up to 48 kHz), Dolby  
Digital, DTS  
Video Section  
Outputs  
251 mm × 1,205 mm × 251  
mm (10 in × 47 1/2 in ×  
10 in) (w/h/d) (whole  
speaker)  
VIDEO: 1 Vp-p 75 ohms  
COMPONENT:  
Y: 1 Vp-p 75 ohms  
PB/CB, PR/CR: 0.7 Vp-p  
75 ohms  
Mass (approx.)  
0.9 kg (2 lb) (wall-  
mounted part)  
HDMI OUT: Type A (19  
pin)  
2.7 kg (6 lb) (whole  
speaker)  
BD/DVD/Super Audio CD/CD System  
Signal format system  
Center (SS-CTB101)  
NTSC  
Speaker system  
Full range Acoustic  
suspension, Magnetically  
Shielded  
USB Section  
(USB) port:  
Type A (For connecting  
USB memory, memory  
card reader, digital still  
Speaker unit  
30 mm × 60 mm (1 3/16 in ×  
2 3/8 in) cone type  
3 ohms  
Rated impedance  
US  
75  
 
Dimensions (approx.)  
Mass (approx.)  
290 mm × 49 mm × 49 mm  
(11 1/2 in × 1 15/16 in ×  
1 15/16 in) (w/h/d)  
802.11b: 11, 5.5, 2 and 1  
Mbps  
802.11n: up to 300 Mbps  
(40 MHz/spatial streams:  
2)  
Tx: up to 500 mA  
USB Wireless LAN  
Adapter: 27 g (1 oz)  
0.28 kg (10 oz)  
Subwoofer (SS-WSB101) for BDV-E870/  
BDV-E370/BDV-T37  
Speaker system  
Speaker unit  
Rated impedance  
Dimensions (approx.)  
Power consumption:  
Mass (Approx.):  
Subwoofer Bass reflex  
160 mm (6 3/8 in) cone type  
3 ohms  
260 mm × 320 mm × 260  
mm (10 1/4 in × 12 5/8 in ×  
10 1/4 in) (w/h/d)  
Dimensions (Approx.) (w × h × d):  
USB Wireless LAN  
Adapter: 96 mm × 14 mm  
× 27 mm (3 7/8 in × 9/16 in ×  
1 1/8 in)  
Mass (approx.)  
5.2 kg (11 lb 8 oz)  
Subwoofer (SS-WSB102) for BDV-E570/  
BDV-E470/BDV-T57  
* The frequency and channel differ depending on the  
area.  
Speaker system  
Speaker unit  
Rated impedance  
Dimensions (approx.)  
Subwoofer Bass reflex  
180 mm (7 1/8 in) cone type  
3 ohms  
275 mm × 405 mm × 275  
mm (10 7/8 in × 16 in ×  
10 7/8 in) (w/h/d)  
**The transmission speed differs depending on the  
distance and number of obstructions between the  
transmission products, the configuration of  
products, the radio wave conditions, the line traffic,  
and the products that you use. The transmission may  
also be cut off depending on the radio wave  
conditions. The standard values of the transmission  
speed are the theoretical maximum values for the  
wireless standards. They are not the actual speeds of  
data transmission.  
Mass (approx.)  
7.5 kg (16 lb 12 oz)  
General  
Power requirements  
North American and Mexican models:  
120 V AC, 60 Hz  
Latin American models: 110 V - 240 V AC,  
50/60 Hz  
Design and specifications are subject to change  
without notice.  
Power consumption  
Dimensions (approx.)  
On: 170 W  
• Standby power consumption 0.3 W.  
Standby: 0.3 W (at the  
Power Saving mode)  
430 mm × 85 mm × 335  
mm (17 in × 3 3/8 in ×  
13 1/4 in) (w/h/d) incl.  
projecting parts  
• Halogenated flame retardants are not used in the  
certain printed wiring boards.  
• Over 85% power efficiency of amplifier block is  
achieved with the full digital amplifier, S-Master.  
Mass (approx.)  
4.8 kg (10 lb 10 oz)  
USB Wireless LAN Adapter (UWA-BR100)  
for BDV-E570/BDV-T57  
Standards Compliance:  
Host Interface:  
Security:  
IEEE 802.11a/b/g/n  
USB 2.0  
64/128 bit: WEP, WPA/  
WPA2, WPS  
Frequency and Channel*: 2.4 GHz - 2.4835 GHz  
[CH1 - 11]  
5.15 GHz - 5.25 GHz  
[CH36 - 48]  
5.25 GHz - 5.35 GHz  
[CH52 - 64]  
5.47 GHz - 5.725 GHz  
[CH100 - 140]  
5.725 GHz - 5.85 GHz  
[CH149 - 165]  
Data Rate**:  
802.11a/g: 54, 48, 36, 24,  
18, 12, 9 and 6 Mbps  
US  
76  
Language Code List  
The language spellings conform to the ISO 639: 1988 (E/F) standard.  
Code Language  
Code Language  
Code Language  
Code Language  
1027 Afar  
1183 Irish  
1347 Maori  
1507 Samoan  
1508 Shona  
1509 Somali  
1511 Albanian  
1512 Serbian  
1513 Siswati  
1514 Sesotho  
1515 Sundanese  
1516 Swedish  
1517 Swahili  
1521 Tamil  
1028 Abkhazian  
1032 Afrikaans  
1039 Amharic  
1044 Arabic  
1045 Assamese  
1051 Aymara  
1052 Azerbaijani  
1053 Bashkir  
1057 Byelorussian  
1059 Bulgarian  
1060 Bihari  
1186 Scots Gaelic  
1194 Galician  
1196 Guarani  
1203 Gujarati  
1209 Hausa  
1349 Macedonian  
1350 Malayalam  
1352 Mongolian  
1353 Moldavian  
1356 Marathi  
1357 Malay  
1217 Hindi  
1226 Croatian  
1229 Hungarian  
1233 Armenian  
1235 Interlingua  
1239 Interlingue  
1245 Inupiak  
1358 Maltese  
1363 Burmese  
1365 Nauru  
1369 Nepali  
1376 Dutch  
1379 Norwegian  
1393 Occitan  
1403 (Afan)Oromo  
1408 Oriya  
1417 Punjabi  
1428 Polish  
1525 Telugu  
1527 Tajik  
1061 Bislama  
1066 Bengali;  
Bangla  
1248 Indonesian  
1253 Icelandic  
1254 Italian  
1528 Thai  
1529 Tigrinya  
1531 Turkmen  
1532 Tagalog  
1534 Setswana  
1535 Tonga  
1538 Turkish  
1539 Tsonga  
1540 Tatar  
1067 Tibetan  
1070 Breton  
1079 Catalan  
1093 Corsican  
1097 Czech  
1103 Welsh  
1105 Danish  
1109 German  
1130 Bhutani  
1142 Greek  
1144 English  
1145 Esperanto  
1149 Spanish  
1150 Estonian  
1151 Basque  
1157 Persian  
1165 Finnish  
1166 Fiji  
1257 Hebrew  
1261 Japanese  
1269 Yiddish  
1283 Javanese  
1287 Georgian  
1297 Kazakh  
1298 Greenlandic  
1299 Cambodian  
1300 Kannada  
1301 Korean  
1305 Kashmiri  
1307 Kurdish  
1311 Kirghiz  
1313 Latin  
1326 Lingala  
1435 Pashto; Pushto  
1436 Portuguese  
1463 Quechua  
1481 Rhaeto-  
Romance  
1543 Twi  
1557 Ukrainian  
1564 Urdu  
1482 Kirundi  
1483 Romanian  
1489 Russian  
1491 Kinyarwanda  
1495 Sanskrit  
1498 Sindhi  
1572 Uzbek  
1581 Vietnamese  
1587 Volapük  
1613 Wolof  
1632 Xhosa  
1665 Yoruba  
1684 Chinese  
1697 Zulu  
1501 Sangho  
1502 Serbo-Croatian  
1503 Singhalese  
1505 Slovak  
1327 Laothian  
1332 Lithuanian  
1334 Latvian; Lettish  
1345 Malagasy  
1171 Faroese  
1174 French  
1181 Frisian  
1506 Slovenian  
1703 Not specified  
Parental Control/Area Code List  
Code Area  
Code Area  
Code Area  
Code Area  
2044 Argentina  
2047 Australia  
2046 Austria  
2057 Belgium  
2070 Brazil  
2109 Germany  
2200 Greece  
2219 Hong Kong  
2248 India  
2238 Indonesia  
2239 Ireland  
2254 Italy  
2276 Japan  
2304 Korea  
2376 Netherlands  
2390 New Zealand  
2379 Norway  
2543 Taiwan  
2528 Thailand  
2184 United  
Kingdom  
2427 Pakistan  
2424 Philippines  
2428 Poland  
2090 Chile  
2092 China  
2436 Portugal  
2489 Russia  
2093 Colombia  
2115 Denmark  
2165 Finland  
2174 France  
2501 Singapore  
2149 Spain  
2333 Luxembourg  
2363 Malaysia  
2362 Mexico  
2499 Sweden  
2086 Switzerland  
US  
77  
   
BD-ROM  
BD-ROMs (Blu-ray Disc Read-Only Memory)  
are commercially produced discs and are  
available in the same capacities as the BD  
below. Other than conventional movie and video  
contents, these discs have enhanced features  
such as interactive content, menu operations  
using pop-up menus, selection of subtitle  
display, and slideshow. Although a BD-ROM  
may contain any form of data, most BD-ROM  
discs will contain movies in High Definition  
format, for playback on Blu-ray Disc/DVD  
players.  
Glossary  
AVCHD  
The AVCHD format is a high-definition digital  
video camera format used to record SD  
(standard definition) or HD (high definition)  
signals of either the 1080i specification* or the  
720p specification** on DVDs, using efficient  
data compression coding technology. The  
MPEG-4 AVC/H.264 format is adopted to  
compress video data, and the Dolby Digital or  
Linear PCM system is used to compress audio  
data. The MPEG-4 AVC/H.264 format is  
capable of compressing images at higher  
efficiency than that of the conventional image  
compression format. The MPEG-4 AVC/H.264  
format enables a high definition (HD) video  
signal shot on a digital video camera recorder to  
be recorded on DVD discs in the same way as it  
would be for a standard definition (SD)  
television signal.  
Blu-ray Disc (BD)  
A disc format developed for recording/playing  
high-definition (HD) video (for HDTV, etc.),  
and for storing large amounts of data. A single  
layer Blu-ray Disc holds up to 25 GB, and a  
dual-layer Blu-ray Disc holds up to 50 GB of  
data.  
Digital Cinema Auto Calibration  
(D.C.A.C)  
Digital Cinema Auto Calibration was developed  
by Sony to automatically measure and adjust the  
speaker settings to your listening environment in  
a short period of time.  
* A high definition specification that utilizes 1080  
effective scanning lines and the interlace format.  
**A high definition specification that utilizes 720  
effective scanning lines and the progressive format.  
BD-J application  
Dolby Digital  
The BD-ROM format supports Java for  
interactive functions.  
“BD-J” offers content providers almost  
unlimited functionality when creating  
interactive BD-ROM titles.  
This movie theater sound format is more  
advanced than Dolby Surround Pro Logic. In  
this format, the surround speakers output stereo  
sound with an expanded frequency range, and a  
subwoofer channel for deep bass is  
BD-R  
independently provided. This format is also  
called “5.1” with the subwoofer channel  
designed as the 0.1 channel (since it functions  
only when a deep bass effect is needed). All six  
channels in this format are recorded separately  
for superior channel separation. Furthermore,  
since all the signals are processed digitally, less  
signal degradation occurs.  
BD-R (Blu-ray Disc Recordable) is a  
recordable, write-once Blu-ray Disc, available  
in the same capacities as the BD below. Since  
contents can be recorded and cannot be  
overwritten, a BD-R can be used to archive  
valuable data or store and distribute video  
material.  
BD-RE  
Dolby Digital Plus  
BD-RE (Blu-ray Disc Rewritable) is a  
recordable and rewritable Blu-ray Disc,  
available in the same capacities as the BD  
below. The re-recordable feature makes  
extensive editing and time-shifting applications  
possible.  
Developed as an extension to Dolby Digital, the  
audio coding technology supports 7.1 multi-  
channel surround sound.  
US  
78  
               
Dolby Pro Logic II  
DTS-HD Master Audio  
Dolby Pro Logic II creates five full-bandwidth  
output channels from 2 channel sources. This is  
done using an advanced, high-purity matrix  
surround decoder that extracts the spatial  
properties of the original recording without  
adding any new sounds or tonal colorations.  
DTS-HD Master Audio has a maximum  
transmission rate of 24.5 Mbps, and uses  
lossless compression, and DTS-HD Master  
Audio corresponds to a maximum sampling  
frequency of 192 kHz, and maximum of 7.1ch.  
HDMI (High-Definition Multimedia  
Interface)  
x Movie mode  
The Movie mode is for use with stereo television  
shows and all programs encoded in Dolby  
Surround. The result is enhanced sound field  
directionality that approaches the quality of  
discrete 5.1-channel sound.  
HDMI is an interface that supports both video  
and audio on a single digital connection,  
allowing you to enjoy high quality digital  
picture and sound. The HDMI specification  
supports HDCP (High-bandwidth Digital  
Content Protection), a copy protection  
technology that incorporates coding technology  
for digital video signals.  
Dolby Surround Pro Logic  
As one method of decoding Dolby Surround,  
Dolby Surround Pro Logic produces four  
channels from 2 channel sound. Compared with  
the former Dolby Surround system, Dolby  
Surround Pro Logic reproduces left-to-right  
panning more naturally and localizes sounds  
more precisely. To take full advantage of Dolby  
Surround Pro Logic, you should have one pair of  
surround speakers and a center speaker. The  
surround speakers output monaural sound.  
Interlace format  
(Interlaced scanning)  
The Interlace format is the NTSC standard  
method for displaying TV images at 30 frames  
per second. Each frame is scanned twice -  
alternately between the even numbered scanning  
lines and then odd numbered scanning lines, at  
60 times per second.  
Dolby TrueHD  
LTH (Low to High)  
Dolby TrueHD is a lossless coding technology  
that supports up to 8 channels of multi-channel  
surround sound for the next generation of optical  
discs. The reproduced sound is true to the  
original source bit-for-bit.  
LTH is a recording system that supports organic  
pigment type BD-R.  
Parental Control  
A function of the BD/DVD to limit playback of  
the disc by the age of the users according to the  
limitation level in each country. The limitation  
varies from disc to disc; when it is activated,  
playback is completely prohibited, violent  
scenes are skipped or replaced with other scenes  
and so on.  
DTS  
Digital audio compression technology  
developed by DTS, Inc. This technology  
conforms to 5.1-channel surround. This format  
includes a stereo rear channel and a discrete  
subwoofer channel. DTS provides the same 5.1  
discrete channels of high quality digital audio.  
The good channel separation is realized due to  
the all channel data being recorded discretely  
and processed in digitally.  
PhotoTV HD  
“PhotoTV HD” allows for highly-detailed  
pictures, and photo-like expression of subtle  
textures and colors. By connecting Sony  
“PhotoTV HD” compatible devices using an  
HDMI cable, a whole new world of photos can  
be enjoyed in breathtaking Full HD quality. For  
instance, the delicate texture of the human skin,  
flowers, sand and waves can now be displayed  
on a large screen in beautiful photo-like quality.  
DTS-HD High Resolution Audio  
Developed as an extension to DTS Digital  
Surround format. It supports a maximum  
sampling frequency of 96 kHz, and 7.1 multi-  
channel surround.  
DTS-HD High Resolution Audio has a  
maximum transmission rate of 6 Mbps, with  
lossy compression.  
US  
79  
                   
Pop-up menu  
An enhanced menu operation available on BD-  
ROMs. The pop-up menu appears when POP  
UP/MENU is pressed during playback, and can  
be operated while playback is in progress.  
Progressive format  
(sequential scanning)  
In contrast to the Interlace format, the  
progressive format can reproduce 50 - 60 frames  
per second by reproducing all scanning lines  
(525 lines for the NTSC system). The overall  
picture quality increases and still images, text  
and horizontal lines appear sharper. This format  
is compatible with the 525 or 625 progressive  
format.  
S-AIR  
(Sony Audio Interactive Radio  
frequency)  
Recent times have seen the rapid spread of BD/  
DVD media, digital broadcasting, and other  
high-quality media.  
To ensure that the subtle nuances of these high-  
quality media are transmitted with no  
deterioration, Sony has developed a technology  
called “S-AIR” for the radio transmission of  
digital audio signals with no compression, and  
has incorporated this technology into the EZW-  
RT10/EZW-RT10A/EZW-T100.  
This technology transfers digital audio signals  
with no compression using the 2.4 GHz band  
range of ISM band (Industrial, Scientific, and  
Medical band), such as wireless LANs and  
Bluetooth applications.  
24p True Cinema  
Movies shot with a film camera consist of 24  
frames per second.  
Since conventional televisions (both CRT and  
flat panels) display frames either at 1/60 or 1/50  
second intervals, the 24 frames do not appear at  
an even pace.  
When connected to a TV with 24p capabilities,  
the player displays each frame at 1/24 second  
intervals — the same interval originally shot  
with the film camera, thus faithfully reproducing  
the original cinema image.  
US  
80  
     
Index  
Numerics  
D
M
N
A
Network Connection  
O
P
E
B
BD Hybrid Disc Playback  
F
BD Remote Device  
BD/DVD-ROM 1080/24p  
G
Q
H
HDMI  
R
HDMI (High-Definition  
Registered BD Remote Devices  
Reset to Factory Default  
I
Initialize Personal Information  
C
Internet Video Parental Control  
S
L
US  
81  
 
The software of this system may be updated in the future. To find out details on any  
Printed in Malaysia  
(1)  

Westcott Halo & Apollo 1050 User Manual
Toshiba MA 205 User Manual
Sungale AD1020 User Manual
Sony XS A1323 User Manual
Sony XR C850RDS User Manual
Sony WM ES392 User Manual
Sony MDDISCAM DCM M1 User Manual
Sharp AQUOS BD HP80U User Manual
Samsung VP L750D User Manual
Samsung Camcorder SCB 2000PH User Manual