Sanyo CE42LH2DPB User Manual

INSTRUCTION MANUAL  
LCD Monitor  
CE42LH2R  
CE42LH2DPB  
CE42LH2WP  
Please read this Instruction book before using your LCD monitor.  
We wish you many hours of pleasure from your new LCD monitor.  
GB  
GB  
SAFETY PRECAUTIONS  
CAUTION: Please read and retain for your safety. This unit has been designed and manufactured to assure your personal safety, but  
LPSURSHUꢀXVHꢀFDQꢀUHVXOWꢀLQꢀSRWHQWLDOꢀHOHFWULFꢀVKRFNꢀRUꢀ¿UHꢀKD]DUGVꢆꢀ,QꢀRUGHUꢀQRWꢀWRꢀGHIHDWꢀWKHꢀVDIHJXDUGVꢀLQFRUSRUDWHGꢀLQꢀWKLVꢀPRQLWRUꢀREVHUYHꢀWKHꢀ  
following basic rules for its installation, use and servicing.  
Installation and Use  
(CE42LH2WP model only)  
The operating temperature range of this monitor is guaranteed 0°C  
Do not allow anything to rest on the power  
~ 40°C/32°F ~ 104°F. It is not recommended to install the screen  
cord. Do not locate this LCD monitor where the  
in direct sunlight without adequate shading, as this will cause the  
FRUGꢀZLOOꢀEHꢀGDPDJHGꢀE\ꢀSHRSOHꢀZDONLQJꢀRQꢀLWꢆ  
WHPSHUDWXUHꢀRIꢀWKHꢀSDQHOꢀWRꢀULVHꢀDERYHꢀWKHꢀPD[LPXPꢀVSHFL¿HGꢆꢀ'R-  
LQJꢀVRꢀPD\ꢀFDXVHꢀDꢀEODFNꢀVKDGRZꢀWRꢀDSSHDUꢀRQꢀWKHꢀVFUHHQꢀZKLFKꢀ  
will disappear when the screen temperature returns to within the  
VSHFL¿FDWLRQꢆꢀ7KLVꢀ³RIꢀFRXUVH´ꢀGRHVꢀQRWꢀSURGXFHꢀDQ\ꢀKDUPIXOꢀHIIHFWꢀ  
on the lifetime of the monitor.  
Do not overload wall outlets and extension  
FRUGVꢀDVꢀWKLVꢀFDQꢀUHVXOWꢀLQꢀ¿UHꢀRUꢀHOHFWULFꢀVKRFNꢆ  
$ꢀVXLWDEOHꢀVRFNHWꢀRXWOHWꢀPXVWꢀEHꢀSURYLGHGꢀQHDUꢀ  
to the monitor and shall be easily accessible.  
Do not place this LCD monitor near any heat  
sources such as radiators, heaters, stoves and other heat-generating  
SURGXFWVꢀꢁLQFOXGLQJꢀDPSOL¿HUVꢅꢆꢀ  
Do not apply liquid cleaners or aerosol cleaners directly onto the LCD  
monitor. Use a damp cloth for cleaning.  
Do not place your LCD monitor on an unstable stand, shelf or table.  
Serious injury to an individual, and damage to the LCD monitor may  
result if it should fall. Your sales person can recommend an approved  
ZDOOꢀPRXQWLQJꢀNLWꢆꢀ$ꢀVSHFLDOꢀZDOOꢀPRXQWLQJꢀNLWꢀLVꢀDYDLODEOHꢀIRUꢀWKLVꢀ  
model.  
ADDITIONAL FOR NORTH AMERICA AND CANADA:  
This monitor must NOT be permanently mounted to the building  
structure. It must be mounted in such a way that it can be removed  
using basic tools.  
The power supply cord must NOT be attached to the building surface.  
The power supply cord must NOT be routed through walls, ceiling,  
ÀRRUVꢇꢀRUꢀRWKHUꢀVLPLODUꢀRSHQLQJVꢀLQꢀWKHꢀEXLOGLQJꢀVWUXFWXUHꢆꢀ  
The power supply cord MUST be positioned so as to prevent physical  
damage.  
This LCD monitor should be operated only from the type of power  
source indicated on the monitor or as indicated in the Operating In-  
structions. If you are not sure of the type of power supply, consult your  
sales person or your local power company.  
For added protection it is strongly recommended that this LCD  
monitor has its mains supplied via an approved earth fault protection  
device.  
Important: (UK only)  
THIS PRODUCT MUST BE EARTHED.  
7KLVꢀHTXLSPHQWꢀLVꢀ¿WWHGꢀZLWKꢀDQꢀDSSURYHGꢀPDLQVꢀOHDGꢀDQGꢀDQꢀ  
approved non rewireable UK mains plug. To change a fuse in this  
type of plug proceed as follows:  
WARNING: To prevent injury the LCD monitor must be securely  
attached to the wall in accordance with the manufacturers installation  
instructions.  
1. Remove the fuse cover and fuse.  
IMPORTANT:  
2. Fit a new fuse which should be a BS1362 13 Amp A.S.T.A. or  
BSI approved type.  
This product must be earthed.  
This unit is not disconnected from the mains unless the mains lead  
LVꢀXQSOXJJHGꢆꢀ7KHꢀLQVWDOOHUꢀPXVWꢀPDNHꢀVXUHꢀWKDWꢀWKHꢀZDWHUSURRIꢀLQOLQHꢀ  
coupler is easily accessible.  
3.ꢀ(QVXUHꢀWKDWꢀWKHꢀIXVHꢀFRYHUꢀLVꢀFRUUHFWO\ꢀUH¿WWHGꢆ  
If the fuse cover is lost or damaged the plug must NOT be used  
but replaced with a serviceable plug.  
(CE42LH2WP model only)  
,IꢀWKHꢀ¿WWHGꢀSOXJꢀLVꢀQRWꢀVXLWDEOHꢀIRUꢀ\RXUꢀVRFNHWꢀRXWOHWVꢇꢀLWꢀVKRXOGꢀEHꢀ  
FXWꢀRIIꢀDQGꢀDQꢀDSSURSULDWHꢀSOXJꢀ¿WWHGꢀLQꢀLWVꢀSODFHꢆꢀ,IꢀWKHꢀPDLQVꢀSOXJꢀ  
contains a fuse, this should have a rating of 13 Amp, ensure the  
IXVHꢀFRYHUꢀLVꢀFRUUHFWO\ꢀ¿WWHGꢆꢀ,IꢀDꢀSOXJꢀZLWKRXWꢀDꢀIXVHꢀLVꢀXVHGꢇꢀWKHꢀ  
fuse at the distribution board should not be greater than 13 Amp.  
This monitor is tested to IP66 standard rating.  
This monitor is not protected against temporary or continuous  
immersion in liquid.  
Do not use immediately after moving the LCD monitor from a low  
temperature to a high temperature environment, as this causes con-  
GHQVDWLRQꢇꢀZKLFKꢀPD\ꢀUHVXOWꢀLQꢀ¿UHꢇꢀHOHFWULFꢀVKRFNꢇꢀRUꢀRWKHUꢀKD]DUGVꢆꢀ  
%HIRUHꢀFOHDQLQJꢇꢀXQSOXJꢀWKHꢀPRQLWRUꢀIURPꢀWKHꢀZDOOꢀVRFNHWꢆꢀ  
Note: The severed plug must be destroyed to avoid a possible  
VKRFNꢀKD]DUGꢀVKRXOGꢀLWꢀEHꢀLQVHUWHGꢀLQWRꢀDꢀꢃꢈꢀ$PSꢀVRFNHWꢀHOVH-  
where.  
The wires in this mains lead are coloured in accordance with the  
following code:  
Do notꢀPRXQWꢀQHDUꢀDQꢀRSHQꢀÀDPHꢀVRXUFHꢆꢀ2SHQꢀÀDPHVꢀPXVWꢀQHYHUꢀ  
be used near this LCD monitor.  
Blue  
Brown  
Neutral  
Live  
This LCD monitor should not be built in or enclosed in any way, heat  
build up will reduce the life of the monitor.  
Green and Yellow  
Earth  
This LCD monitor should have a minimum distance of 5cm away from  
the wall and the monitor should have 10cm distance around the top  
and sides.  
1. The Blue wire must be connected to the terminal which is  
PDUNHGꢀZLWKꢀWKHꢀOHWWHUꢀ³1´ꢀRUꢀFRORXUHGꢀ%/$&.ꢆ  
2. The Brown wire must be connected to the terminal with the  
AlwaysꢀPRXQWꢀXVLQJꢀUHFRPPHQGHGꢀDQGꢀVXEVWDQWLDOꢀ¿[WXUHVꢀDQGꢀ¿W-  
letter “Lor coloured RED.  
tings.  
3. The Green and Yellow wire must be connected to the terminal  
ZKLFKꢀLVꢀPDUNHGꢀZLWKꢀWKHꢀOHWWHUꢀ³(´ꢀRUꢀFRORXUHGꢀ*5((1ꢀRUꢀ  
GREEN and YELLOW.  
10cm  
%HIRUHꢀUHSODFLQJꢀWKHꢀSOXJꢀFRYHUꢇꢀPDNHꢀFHUWDLQꢀWKDWꢀWKHꢀFRUGꢀJULSꢀLVꢀ  
clamped over the sheath of the lead - not simply over the wires.  
5cm  
10cm  
10cm  
Do not attempt to bypass the safety purpose of the grounding  
type plug.  
THIS UNIT IS NOT DISCONNECTED FROM THE MAINS UN-  
LESS THE MAINS LEAD IS UNPLUGGED.  
7KHꢀUHDUꢀ¿QQHGꢀVHFWLRQꢀDURXQGꢀWKHꢀFDELQHWꢀIXQFWLRQVꢀDVꢀDꢀKHDWꢀVLQNꢇꢀ  
removing heat away from the monitor. The external surface of the  
FDELQHWꢀꢁ¿QQHGꢀDUHDꢅꢀPXVWꢀQRWꢀEHꢀFRYHUHGꢀRUꢀWKHꢀDLUÀRZꢀUHVWULFWHGꢀLQꢀ  
anyway by enclosing the LCD monitor.  
THE INSTALLER MUST MAKE SURE THE MAINS LEAD IS  
EASILY ACCESSIBLE.  
3
GB  
GB  
SERVICING  
Servicing  
Your monitor is fully transistorised and does not contain any user serviceable components.  
You must not remove the rear cover of the monitor by yourself. The apparatus is working with high voltages and could damage  
objects or even endanger people. Leave all required repair and service jobs to an authorised service technician. He will exclusively  
use such spare parts that are complying with the same safety standards as applicable to the original parts. The use of original  
VSDUHꢀSDUWVꢀFDQꢀSUHYHQWꢀ¿UHꢁꢀVKRFNꢀDQGꢀRWKHUꢀKD]DUGVꢂ  
8QSOXJꢀWKHꢀ/&'ꢀPRQLWRUꢀIURPꢀWKHꢀZDOOꢀRXWOHWꢀDQGꢀUHIHUꢀVHUYLFLQJꢀWRꢀTXDOL¿HGꢀVHUYLFHꢀSHUVRQQHOꢀXQGHUꢀWKHꢀIROORZLQJꢀ  
conditions:  
N If the power cord or plug is damaged.  
N If liquid has been spilt in to the LCD monitor.  
N If the LCD monitor has been dropped or the cabinet has been damaged.  
N If the LCD monitor exhibits a distinct change in performance.  
N If the LCD monitor does not operate normally by following the operating instructions.  
N If the LCD monitor has been exposed to rain or water. (CE42LH2R/CE42LH2DPB model only)  
Adjust only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage.  
7KLVꢀZLOOꢀRIWHQꢀUHTXLUHꢀH[WHQVLYHꢀZRUNꢀE\ꢀDꢀTXDOL¿HGꢀWHFKQLFLDQꢀWRꢀUHVWRUHꢀWKHꢀPRQLWRUꢀWRꢀQRUPDOꢀRSHUDWLRQꢆ  
Important recycling information.  
Your SANYO product is designed and manufactured with high quality materials and components  
which can be recycled and reused.  
This symbol means that electrical and electronic equipment, at their end-of-life, should be dis-  
posed of separately.  
In the European Union there are separate collection systems for used electrical and electronic  
products.  
Please help us to conserve the environment we live in!  
Note:7KLVꢀV\PEROꢀPDUNꢀDQGꢀUHF\FOHꢀV\VWHPꢀDUHꢀDSSOLHGꢀRQO\ꢀWRꢀ(8ꢀFRXQWULHVꢀDUHꢀQRWꢀDSSOLHGꢀWRꢀ  
other countries of the world.  
Federal Communications Commission Notice  
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits  
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This  
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,  
PD\ꢀFDXVHꢀKDUPIXOꢀLQWHUIHUHQFHꢀWRꢀUDGLRꢀFRPPXQLFDWLRQVꢆꢀ2SHUDWLRQꢀRIꢀWKLVꢀHTXLSPHQWꢀLQꢀDꢀUHVLGHQWLDOꢀDUHDꢀLVꢀOLNHO\ꢀWRꢀFDXVHꢀKDUPIXOꢀLQWHUIHU-  
ence in which case the user will be required to correct the interference at his own expense.  
'RꢀQRWꢀPDNHꢀDQ\ꢀFKDQJHVꢀRUꢀPRGL¿FDWLRQVꢀWRꢀWKHꢀHTXLSPHQWꢀXQOHVVꢀRWKHUZLVHꢀVSHFL¿HGꢀLQꢀWKHꢀLQVWUXFWLRQVꢆꢀ,IꢀVXFKꢀFKDQJHVꢀRUꢀPRGL¿FDWLRQVꢀ  
should be made, you could be required to stop operation of the equipment.  
Canadian Radio Interference Regulations  
This Class A digital apparatus meets all requirements of the Canadian ICES-003.  
WARNING  
7KLVꢀLVꢀDꢀ&ODVVꢀ$ꢀSURGXFWꢆꢀ,QꢀDꢀGRPHVWLFꢀHQYLURQPHQWꢀWKLVꢀSURGXFWꢀPD\ꢀFDXVHꢀUDGLRꢀLQWHUIHUHQFHꢀLQꢀZKLFKꢀFDVHꢀWKHꢀXVHUꢀPD\ꢀEHꢀUHTXLUHGꢀWRꢀWDNHꢀ  
adequate measures.  
4
GB  
GB  
SERVICING  
AC Power Cord Requirement  
The AC Power Cord supplied with this LCD monitor meets the requirement for use in the country in which you  
purchase it.  
AC Power Cord for the United States and Canada:  
GROUND  
$&ꢀ3RZHUꢀ&RUGꢀXVHGꢀLQꢀWKHꢀ8QLWHGꢀ6WDWHVꢀDQGꢀ&DQDGDꢀLVꢀOLVWHGꢀE\ꢀWKHꢀ8QGHUZULWHUVꢀ/DERUDWRULHVꢀꢁ8/ꢅꢀDQGꢀFHUWL¿HGꢀ  
by the Canadian Standard Association (CSA).  
$&ꢀ3RZHUꢀ&RUGꢀKDVꢀDꢀJURXQGLQJꢂW\SHꢀ$&ꢀOLQHꢀSOXJꢆꢀ7KLVꢀLVꢀDꢀVDIHW\ꢀIHDWXUHꢀWRꢀPDNHꢀVXUHꢀWKDWꢀWKHꢀSOXJꢀZLOOꢀ¿WꢀLQWRꢀWKHꢀSRZHUꢀRXWOHWꢆꢀ  
Do not try to defeat this safety feature. Should you be unable to insert the plug into the outlet, contact your electrician.  
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE  
End-User License  
The product (meaning the equipment or appliance to which this documentation relates) incorporates Software (the software applications, utili-  
ties and modules embedded within the Product) which is owned by Sanyo or its licensors. Before using the product, please read the End-User  
License Conditions detailed below. If you do not agree to the terms and conditions of the End-User License, Please do not proceed to use the  
3URGXFWꢂꢀUHSDFNꢀWKHꢀ3URGXFWꢀXQXVHGꢀDQGꢀUHWXUQꢀLWꢀWRꢀ\RXUꢀVXSSOLHUꢀWRJHWKHUꢀZLWKꢀSURRIꢀRIꢀSXUFKDVHꢀIRUꢀDꢀIXOOꢀUHIXQGꢆꢀ%\ꢀXVLQJꢀWKHꢀSURGXFWꢇꢀ\RXꢀ  
agree to be bound by the terms and conditions of the End-User License.  
/LFHQVHꢀ*UDQWꢁꢀ&RQGLWLRQVꢀDQGꢀUHVWULFWLRQV  
1. Sanyo grants you a non-exclusive, world-wide (subject to export controls), non-transferable (except as permitted by 2 below), royalty-free  
license to use the Software upon and with the Product.  
2. You may not transfer any of your license rights in the Software without the prior written consent of SANYO and if consent is provided then  
the Software shall only be transferred in conjunction with the transfer of the Product AND provided that the transferee has read and agreed  
to accept the terms and conditions of this license.  
3.<RXꢀPXVWꢀHQVXUHꢀWKDWꢀWKHꢀFRS\ULJKWꢇꢀWUDGHPDUNꢀDQGꢀRWKHUꢀSURWHFWLYHꢀQRWLFHVꢀFRQWDLQHGꢀLQꢀWKHꢀ6RIWZDUHꢀDUHꢀPDLQWDLQHGꢀDQGꢀQRWꢀDOWHUHGꢀRUꢀ  
removed.  
4. The Software provided hereunder is copyrighted and licensed (not sold). SANYO especially does not transfer title or and ownership rights  
in the Software to you. The Software provided hereunder may contain or be derived from portions of materials provided to SANYO under  
license by a third party supplier.  
5. Except as expressly permitted by statute you may not;  
L use the Software in conjunction with any other computer hardware other than the product;  
L copy all or part of the Software;  
L incorporate all (or any of) the Software into other programs developed by (or on behalf of) you and/or used by you;  
L reverse-engineer, decompile or disassemble the Software;  
L PDNHꢀWKHꢀ6RIWZDUHꢀꢁRUꢀDQ\ꢀSDUWꢀRIꢀLWꢅꢀDYDLODEOHꢇꢀRUꢀSHUPLWꢀLWVꢀUHGLVWULEXWLRQꢇꢀIRUꢀXVHꢀZLWKꢀDQ\ꢀFRPSXWHUꢀKDUGZDUHꢀRWKHUꢀWKDQꢀWKHꢀ3URGXFWꢉꢀRUꢀꢀꢀꢀꢀꢀ  
rent, lease, gift, loan, sell, distribute or transfer possession of the whole or any part of the Software.  
Termination  
This license is effective until terminated. This license will terminate automatically without notice if you fail to comply with any of its provisions.  
Disclaimer  
1. The Software is(to the extent permitted by law) supplied “as is” and SANYO and its suppliers expressly exclude all warranties, express or  
LPSOLHGꢇꢀLQFOXGLQJꢀꢁEXWꢀQRWꢀOLPLWHGꢀWRꢅꢀZDUUDQWLHVꢀRIꢀVDWLVIDFWRU\ꢀTXDOLW\ꢇꢀ¿WQHVVꢀIRUꢀSXUSRVHꢀDQGꢀQRQꢂLQIULQJHPHQWꢀꢁVDYHꢀWRꢀWKHꢀH[WHQWꢀWKDWꢀWKHꢀ  
same are not capable of exclusion at law).  
2.,QꢀQRꢀFLUFXPVWDQFHVꢀZLOOꢀ6$1<2ꢀEHꢀOLDEOHꢀIRUꢀDQ\ꢀGLUHFWꢇꢀLQGLUHFWꢇꢀFRQVHTXHQWLDOꢇꢀRUꢀLQFLGHQWDOꢀGDPDJHꢀꢁLQFOXGLQJꢀORVVꢀRIꢀSUR¿WVꢇꢀEXVLQHVVꢀ  
interruption, loss of data or the cost of procurement of substitute goods, technology or services) arising out of the use or the inability to use  
the Software (save to the extent that such liability is not capable of exclusion at law).  
General  
1. This End-User License will be governed by laws of England and the User may only bring claims in the English Courts and SANYO shall be  
entitled to bring a claim in the courts of any jurisdiction.  
2. This End-User License is governed by the laws of the State of California. The End-User and Sanyo agree that any action to enforce or inter-  
pret the terms of this End-User License shall be brought only in the appropriate state or federal court located in Los Angeles County, Califor-  
nia.The End-User and Sanyo hereby submit to the exclusive jurisdiction and venue of such court.  
3. The above terms and conditions supersede any prior agreement, oral or written, between you and SANYO relating to the Software.  
5
GB  
GB  
INSTALLATION  
Step: 1 Mains Connection  
N&RQQHFWꢀWKHꢀGLVSOD\ꢀXQLWꢀWRꢀ9*$ꢁꢀ%1&ꢀDQGꢀ6FDUWꢀFRQ-  
nector as required.  
LD-Net  
ꢍꢀ7KLVꢀ¿JXUHꢀLVꢀ&(ꢎꢊ/+ꢊ:3ꢆ  
4. AV3  
Composite (CVBS) signal input.  
1. Connect the in-line power connector to the Mains Inlet as shown  
above.  
AV3-OUT can be used to output the incoming AV3 signal to the  
other monitor.  
2. Connect the power cord of the LCD monitor to a suitable wall outlet.  
As this product does not have a mains On/Off switch, please  
ensure your mains plug is easily accessible.  
5. DVI-D (Digital Video Interface)  
DVI-D supports a large range of resolutions as shown on page 17.  
The LCD monitor is prepared for a mains voltage AC100 ~ 240V,  
50Hz/60Hz. To completely switch off the mains, or when the  
display unit is not to be used for an extended period of time, it is  
advisable to disconnect the power cord from the power outlet.  
6. PC connection  
PC input (PC-IN D-SUB). This input supports a large range of reso-  
lutions as shown page 17. Audio can be connected via the 3.5mm  
PC-AUDIO IN.  
A
C
M
ains  
O
u
t
l
e
t
7. External Speaker  
Output the audio signal from AV1, AV2, AV3, PC and DVI.  
7KHꢀVSHDNHUꢀLPSHGDQFHꢀLVꢀꢌꢀRKPVꢆ  
Please use the correct mains lead supplied with the set for your  
area.  
3. Warning: To prevent injury, the unit must be securely attached to  
the wall in accordance with the installation instructions.  
WARNING! High voltages are used in the  
RSHUDWLRQꢀRIꢀWKLVꢀVHWꢆꢀ5HIHUꢀVHUYLFHꢀWRꢀTXDOL¿HGꢀ  
service personnel.  
8. AV2 / DVI AUDIO IN  
Connect the audio output (stereo) from a computer or video equip-  
ment connected AV2 or DVI.  
Step: 2 Connections  
N INPUT selection  
7RꢀVZLWFKꢀHLWKHUꢀ$9ꢃꢇꢀ5*%ꢇꢀ$9ꢊꢇꢀ$9ꢈꢇꢀ3&ꢇꢀ'9,ꢀRUꢀ1HWZRUNꢀE\ꢀSUHVV-  
ing the INPUT button on your remote control repeatedly.  
1. AV1  
SCART connection/CVBS/RGB/S-VIDEO.  
2. RGB  
9. Monitor Audio OUT  
7KLVꢀWHUPLQDOVꢀRXWSXWꢀ¿[HGꢀOHYHOꢀIURPꢀ$8',2ꢀ,1ꢆ  
TTL input (5V RGB signals) into SCART terminal.  
ꢃꢂꢀ<ꢁꢀ3Eꢁꢀ3Uꢄ5*%+9ꢀFRQQHFWLRQꢀꢅ$9ꢆꢇ  
10. RS232C IN/OUT  
Choose Y, Pb, Pr or RGB H/V connection by selecting AV2 Setting  
in Set up menu (see page 10). You can connect your DVD player  
to the Y, Pb, Pr terminals instead of using a scart lead. This can  
VXSSRUWꢀKLJKꢀGH¿QLWLRQꢀLQꢀDQDORJXHꢀFRPSRQHQWꢀIRUPꢆꢀ5*%ꢀ+ꢋ9ꢀFDQꢀ  
be used as a PC input via the BNC terminals. Both options support  
a large range of resolutions (page 17). AV2-OUT can be used to  
output the incoming AV2 signal to the other monitor.  
ꢀꢀ:KHQꢀWKHꢀPRQLWRUꢀLVꢀFRQWUROOHGꢀE\ꢀDꢀFRPSXWHUꢇꢀFRQQHFWꢀWRꢀWKLVꢀMDFNꢀ  
with serial control cable.  
You can connect to another monitor with RS232C OUT.  
:KHQꢀ\RXꢀFRQQHFWꢀ3&ꢀZLWKꢀ56ꢊꢈꢊ&ꢇꢀVHOHFWꢀ³21´ꢀDWꢀ1HWZRUNꢀ  
standby in Installation mode.  
If it is selected “OFF”, RS232C terminals do not functional. Also  
select push button to “SERIAL PORT”.  
6
GB  
GB  
INSTALLATION  
Remote control  
Standby  
Input  
To switch the monitor on and off. Also see page 8.  
To switch input source from AV1, RGB, AV2, AV3,  
PC, DVI or Network mode.  
Recall  
To display input selection information and the Time  
set.  
You can also select colour systems in AV1/AV3  
mode as follows: AUTO í PAL í SECAM í  
NTSC í NTSC4.43 í PAL M í PAL N.  
Wide  
To select the screen mode Full, Full All, Zoom  
16:9, Title in 16:9, Zoom 14:9, Title in 14:9,  
Normal or Natural wide.  
Refer to page 12.  
Auto PC  
It can also be automatically adjusted in PC mode  
by pressing this button for twice .  
Menu  
To enter and exit the main menu, and sub menu.  
Back  
Used to return to the previous menu.  
Up and Down  
To select the next or previous item.  
Level Up/Down  
To adjust the sound volume level or enter sub  
menus.  
F/OK  
Sound Mute  
7RꢀFRQ¿UPꢀWKHꢀLQLWLDOꢀVHWWLQJꢀLQꢀWKHꢀPHQXꢆ  
7RꢀPXWHꢀWKHꢀVRXQGꢀIURPꢀWKHꢀVSHDNHUVꢆ  
The sound changes as follows: Normal volume  
Mute.  
Picture mode selector  
Press the  button repeatedly to select the fol-  
lowing picture mode.  
Personal - Personal preference mode.  
Standard - Normal viewing mode.  
Dynamic - Suitable for brightly lit rooms.  
Soft - Low contrast setting  
Bass Expander  
To get an emphasised bass sound ON or OFF.  
TXT/TV  
To select Teletext mode.  
Eco - Suitable for dimly lit rooms and gives a cin-  
HPDꢂOLNHꢀHIIHFWꢆ  
Main/Sub Picture Swap  
To swap Main and Sub picture.  
)UHH]H  
To switch picture still on or off.  
ON/OFF  
To switch OFF í PIP(1) í PIP(2) í POP mode  
Green  
in turn.  
Press this button for more than 5 seconds, installa-  
tion mode will appear.  
Refer to page 13.  
FOR EU USERS  
Remote control battery installation  
7KHꢀV\PEROꢀPDUNꢀDQGꢀUHF\FOLQJꢀV\VWHPVꢀGHVFULEHGꢀEHORZꢀDSSO\ꢀWRꢀ(8ꢀ  
countries and do not apply to countries in other areas of the world.  
Your SANYO product is designed and manufactured with high quality  
materials and components which can be recycled and/or reused.  
7KHꢀV\PEROꢀPDUNꢀPHDQVꢀWKDWꢀHOHFWULFDOꢀDQGꢀHOHFWURQLFꢀHTXLSPHQWꢇꢀ  
batteries and accumulators, at their end-of-life, should be disposed of  
separately from your household waste.  
Note:  
,IꢀDꢀFKHPLFDOꢀV\PEROꢀLVꢀSULQWHGꢀEHQHDWKꢀWKHꢀV\PEROꢀPDUNꢇꢀWKLVꢀFKHPL-  
cal symbol means that the battery or accumulator contains a heavy  
metal at a certain concentration. This will be indicated as follows: Hg:  
mercury, Cd: cadmium, Pb: lead  
In the European Union there are separate collection systems for used  
electrical and electronic equipment, batteries and accumulators.  
Please, dispose of them correctly at your local community waste col-  
lection/recycling centre.  
Please, help us to conserve the environment we live in!  
,QVWDOOꢀWZRꢀ³$$´ꢀꢃꢆꢄꢀYROWꢀEDWWHULHVꢀVRꢀWKDWꢀWKHꢀ³ꢏ´ꢀDQGꢀ³±´ꢀPDUNVꢀRQꢀWKHꢀ  
EDWWHULHVꢀPDWFKꢀWKHꢀ³ꢏ´ꢀDQGꢀ³±´ꢀPDUNVꢀLQVLGHꢀWKHꢀXQLWꢀLQWRꢀWKHꢀUHPRWHꢀ  
control handset.  
7
GB  
GB  
INSTALLATION  
Controls and Menus  
Menu Operation  
Many of your monitors functions are controlled through the menu  
function, using the remote control.  
MENU  
Picture  
Brightness  
Contrast  
Color  
Tint (only if NTSC equipment is detected)  
Sharpness  
White Tone  
White Tone / R / G / B  
Advanced Setting  
DCDi / ACC/ACM / CCS / DNR / MPEG NR / Film Mode  
Sound  
Time  
Treble  
Bass  
Balance  
On / Off  
Bass Expander  
Current Weekday  
Current Time  
Schedule  
Weekday  
Time  
1 - 20  
Action  
Power On / Power Off  
On Program  
AV1 / RGB / AV2 / AV3 / PC / DVI / Network  
On / Off  
Active  
Setup Menu Setup  
Language / H/V-Position / Duration / Transparence  
PIP / POP Setup  
PIP/POP Mode / Main/Sub Source / PIP Position  
Initial Settings  
Text Language  
Tile Mode  
Western / Eastern / Russian / Arabic / Farsi  
Tile Mode Active / H/V_Sets / H/V Location / Bezel H/V Adjustment  
q
w
AV2 Setting  
XGA Mode  
RGBHV / YPbPr  
XGA / WXGA 1366x768  
On / Off  
PC Power save  
PC Adj. Auto Adjust  
H-Position  
V-Position  
Clock  
The LCD display has a Standby light to show there is power.  
å
Phase  
Switching into/from standby mode  
During menu operation the bottom of the on screen display will show  
which controls can be used for menu navigation.  
Press the MENU button to enter the main menu. Whenever main  
menu is accessed initially, PICTURE will be the default selection.  
The Standby mode is used for switching the LCD monitor off for short  
periods of time. In standby mode the monitor is switched off but is still  
receiving mains power.  
L To turn the monitor into standby mode, press the  button.  
The blue power indicator illuminates more brightly.  
A sub menu is selected using the  or  button and pressing  
the  or  button when the required sub menu is highlighted.  
:KHQꢀ\RXꢀKDYHꢀ¿QLVKHGꢀ\RXꢀFDQꢀSUHVVꢀWKHꢀBACK button to return to  
the previous menu, press the MENU button to exit the menu operation.  
L To turn the monitor ON from standby mode, press the  button  
again.  
,Iꢀ\RXꢀ¿QGꢀWKHꢀSRZHUꢀLQGLFDWRUꢀÀDVKLQJꢇꢀGLVFRQQHFWꢀ  
power cord from the power outlet and contact our  
6HUYLFHꢀGHVNꢆ  
7KLVꢀZDUQLQJꢀLVꢀDꢀVLJQꢀWRꢀOHWꢀ\RXꢀNQRZꢀWKDWꢀWKHꢀ  
power protection function of this TV set is now  
operating.  
Picture menu  
1. Press the MENU button. PICTURE will be the default selection.  
Press the  or  button to enter.  
Set the picture settings for your “personal” preference.  
Control buttons (bottom corner of back cover)  
ç
Menu button: Used to display or cancel main menu.  
Input/4 button: Switch between AV1, RGB, AV2, AV3, PC , DVI  
RUꢀ1HWZRUNꢀPRGHꢆꢀ,WꢀLVꢀDOVRꢀXVHGꢀWRꢀSURYLGHꢀVXEꢀ  
menu selection from the Main Menu.  
2. Use the  or  button to select eg. Brightness and the  or  
 button to adjust levels.  
 or  buttons: provide up and down adjustments.  
N White Tone  
May be used to adjust the color tone of the picture. Use the  or  
 button to select White Tone and press the  or  button  
to enter the sub menu. You can select Personal, Cool, Standard or  
Warm settings by using the  or  button. To adjust the color  
tone of the picture by using the  or  button to select Red(R),  
Green(G) or Blue(B) and the  or  button to adjust levels.  
These settings will be stored in personal mode automatically.  
 button: To switch to standby mode (to switch off completely  
disconnect the monitor from the power supply).  
8
GB  
GB  
MENU OPERATION  
N Current Weekday  
8VHꢀWRꢀVHWꢀFXUUHQWꢀZHHNGD\ꢀXVLQJꢀWKHꢀ or  button.  
Picture menu  
N Advanced settings  
N Current Time  
Use to set the current time using the Numeric buttons.  
Use the  or  button to select Advanced settings and press  
the  or  button to enter the sub menu as follows.  
Other items in Time Menu should not be selected until Current  
Time has been set.  
N Schedule  
Use to set up to 20 separate time schedules for “Power On” or “Power  
Off”, select 1 ~ 20 using the  or  button.  
N Weekday  
DCDi (Directional Correlational Deinterlacing) is used to process  
moving angled edge in deinterlacing to get the smoothest and most  
natural image. Press the  or  button on the remote control to  
select On or Off.  
8VHꢀWRꢀVHWꢀWKHꢀVFKHGXOHꢀIRUꢀ³3RZHUꢀ2Q´ꢀRUꢀ³3RZHUꢀ2II´ꢀRIꢀDQ\ꢀZHHNGD\ꢀ  
from Sunday through to Saturday or Everyday using the  or  
button.  
ACC/ACM (ACC: Adaptive Contrast and Color; ACM-II: Active Color  
Management-II) is used to select adaptive Brightness, Contrast and  
tone control. Press the  or  button on the remote control to  
select suitable mode either Vivid, Cinema, Sport or Off.  
N Time  
Use to set the schedule for “Power On” or “Power Off” of any time us-  
ing the Numeric buttons.  
CCS (Cross Color Separation) is used to remove residual chroma  
information from luminance signal which is the result of imperfect  
decoding of composite video. Press the  or  button on the  
remote control to select either Auto, Standard or Off.  
N Action  
Use to set the schedule for “Power On” or “Power Off” active using  
the  or  button.  
You can set Power On timer in Time menu selecting “ON” in “On  
Timer Function” in Installation Mode. If it is selected “OFF”, Power On  
display in Time menu does not functional.  
DNR (Digital Noise Reduction) is available for noise reduction. Press  
the  or  button on the remote control to select either Auto,  
Low, Mid, High or Off.  
N On Program  
Use to select AV1, RGB, AV2, AV3, PC, DVI or Network for the  
schedule of “Power On” using the  or  button.  
MPEG NR (MPEG Noise Reduction): Removes unwanted ringing and  
EORFNꢀQRLVHꢀIURPꢀLPDJHVꢀWKDWꢀKDYHꢀXQGHUJRQHꢀ03(*ꢀRUꢀ-3(*ꢀFRP-  
pression and decompression. Press the  or  button on the  
remote control to select On or Off.  
N Active  
Film Modeꢀꢁ,QYHUVHꢀꢈꢐꢊꢀSXOOGRZQꢅꢐꢀ)LOPꢀYVꢆ9LGHRꢂ'HWHFWꢀ¿OPꢆꢀ3HUIRUPHGꢀ  
on material which underwent technologic conversion to video. Press the  
 or  button on the remote control to select On or Off.  
Use to select ON or OFF using the  or  button. When set  
³2))´ꢀWKHꢀDERYHꢀLWHPVꢀ³6FKHGXOH´ꢇꢀ³:HHNGD\´ꢇꢀ³7LPH´ꢇꢀ³$FWLRQ´ꢀRUꢀ³21ꢀ  
Program” will be inactive.  
Use NUMERIC buttons [0 ~ 9] to set On Time. (Action “Power On”  
– 00:00 ~ 23:59)  
Sound menu  
Press the MENU button and select Sound using the  or  but-  
Once On Time has been set, when the set time is reached, the  
monitor will leave the stand-by status and enter to the source  
automatically.  
tons, press the  or  button to enter.  
After On Time has been set, you can go on watching other pro-  
grams. When the set time is reached, the monitor will automatically  
switch to the preset program.  
On Program can only be selected whenAction (Power On) has  
been set.  
Action (Power Off) can be set to turn the monitor into standby at a  
selected time  
Select and adjust to obtain the best sound settings for your environ-  
ment using the  or  button to select Treble, Bass or Balance  
and the  or  button to adjust levels.  
Bass Expander can also be selected using the  or  button  
and pressing the  or  button to select On or Off.  
These settings automatically store when you exit the menu.  
Press the BACK button to return to the previous menu.  
Press the MENU button to exit menu operation.  
Once On Program has been set, when the set time is reached, the  
monitor will enter to the preset source automatically.  
Use the  or  button to select On program, AV1, RGB, AV2,  
AV3, PC, DVI or Network.  
Setup menu  
Press the MENU button and select Setup using the  or  but-  
tons, press the  or  button to enter. Press the BACK but-  
ton to return to the previous menu. Press the MENU button to exit.  
Time menu  
Press the MENU button and select Time using the  or  but-  
tons, press the  or  button to enter. Press the BACK but-  
ton to return to the previous menu. Press the MENU button to exit  
menu operation.  
N Menu Setup  
Whenever Setup menu is accessed initially, Menu Setup will be the  
default selection. Press the  or  button to enter the sub menu.  
9
GB  
GB  
MENU OPERATION  
H_Sets is used to divide the horizonal picture into more than one  
part, but the most is 5 parts (5 monitors).  
V_Sets is used to divide the vertical picture into more than one part,  
and the most is also 5 parts (5 monitors). Using the  or  but-  
ton to set.  
H Location is used to select one part of the horizonal picture to dis-  
play on the current LCD Monitor using the  or  button.  
V Location is used to select one part of the vertical picture to display  
on the current LCD Monitor using the  or  button.  
Language is used to select the preferred language. Use the  or  
 button to select English, French, German, Italian, Spanish or  
Dutch.  
%H]HOꢀ+ꢀ$GMXVWPHQW is used to align the image horizontally with  
respect to the other monitors in the video wall to accommodate the  
bezel width using the  or  button. (0 ~ 10)  
H-Position changes the OSD position horizontally by using the  
or  button.  
%H]HOꢀ9ꢀ$GMXVWPHQW is used to align the image vertically with respect  
to the other monitors in the video wall to accommodate the bezel  
width using the  or  button. (0 ~ 10)  
V-Position changes the OSD position vertically by using the  or  
 button.  
Duration is used to set the display time of the MENU by using the  
 or  button. (5 ~ 120 seconds)  
N AV2 Setting  
Transparence is used to adjust transparence of menu display. Use  
the  or  button to adjust levels.  
Use the  or  button to select AV2 Setting and press the  
or  button to select YPbPr or RGBHV.  
Connect your PC to either PC-IN or RGBHV on the rear of the set.  
Once connected select PC mode or AV2 (RGBHV, see page 6 for AV2  
input settings) via the INPUT button on your remote control.  
The set will become a monitor for the PC.  
N PIP/POP Setup  
Use the  or  button to select PIP/POP Setup and press the  
 or  button to enter the sub menu.  
N XGA Mode  
Use the  or  button to select XGA Mode and press the  or  
 button to select XGA or WXGA 1366 x 768.  
N PC Power Save  
The monitor set automatically turns off with no PC input signal and  
ZDNHVꢀXSꢀZLWKꢀVLJQDOꢀZKLOHꢀ3&ꢀ3RZHUꢀ6DYHꢀLVꢀDFWLYHꢆ  
Use the  or  button to select PC Power Save and press the  
 or  button to select ON or OFF.  
PIP/POP Mode: Using the  or  button select the most suit-  
able mode PIP1, PIP2, POP or Off. (Please refer to page 13.)  
When Mode is set to Off, Sub Source and PIP Position will not  
ZRUNꢆꢀ  
PC Adj. menu  
Main Source is used to select input source (AV1, RGB, AV2, AV3, PC,  
Press the MENU button and select PC Adj. using the  or  
buttons, press the  or  button to enter. Press the BACK  
button to return to the previous menu. Press the MENU button to  
exit menu operation.  
'9,ꢀRUꢀ1HWZRUNꢀꢅꢀIRUꢀPDLQꢀSLFWXUHꢀE\ꢀXVLQJꢀWKHꢀ or  button.  
Sub Source is used to select input source (AV1, AV2, AV3, PC or  
DVI) for sub picture by using the  or  button.  
For a combination of main picture and sub picture: only DVI or  
1HWZRUNꢀLQSXWꢀFDQꢀDVVHPEOHꢀZLWKꢀRWKHUꢀLQSXWꢀVRXUFHꢆꢀ)RUꢀH[DPSOHꢇꢀ  
if main source is selected as AV1 input, then the sub source must  
EHꢀ'9,ꢀRUꢀ1HWZRUNꢀLQSXWꢆ  
PIP Position: Using the  or  button it can be selected Top  
Left, Top Right, Bottom Right or Bottom Left.  
N Initial Settings  
This function returns all setting values except for Installation Mode.  
Auto Adjust is used to automatically detect incoming signal, and  
adjust itself to optimize its performance by using the  or  
button. If the image is not displayed properly, a manual adjustment is  
required (Refer to following adjustments).  
N Text Language  
Use the  or  button to select Text Language and press the  
 or  button to select Western, Eastern, Russian, Arabic or  
Farsi.  
H-Position is used to move the horizontal picture position by using  
the  or  button.  
V-Position is used to move the vertical picture position by using the  
 or  button.  
N Tile Mode  
This function allows you to split an image to suit your monitor grid  
format to create a video wall.  
ClockꢀLVꢀXVHGꢀWRꢀHOLPLQDWHꢀÀLFNHUꢀIURPꢀWKHꢀLPDJHꢀE\ꢀXVLQJꢀWKHꢀ or  
 button.  
Use the  or  button to select Tile Mode and press the  or  
 button to enter the sub menu as follows.  
Tile Mode Active can be set On or Off using the  or  but-  
ton.  
Phase is used to eliminate disorder from the image by using the  
or  button.  
10  
GB  
GB  
INSTALLATION MODE  
N Address  
Set the address for the LCD monitor (0 ~ 999).  
Installation Mode  
L Setting the monitor address in RS232 mode  
G2.02 0000  
Installation Mode  
(DFKꢀPRQLWRUꢀFDQꢀKDYHꢀDꢀVSHFL¿Fꢀ$GGUHVVꢇꢀZKLFKꢀKHOSVꢀFRPPDQGꢀꢀꢀꢀꢀꢀ  
that monitor individually and will not effect to other monitors con-  
nected to a controlling PC Address format command.  
The addressing format command is used for operating multiple  
monitor sets from a single PC via the RS232C command line.  
On program  
Tuner Menu  
Max Volume  
Winter mode  
RC inhibition  
Child Lock  
Address  
Off  
Off  
63  
Off  
Off  
Off  
0
Baud rate  
19200  
N Baud rate  
Panel protection  
AV Auto shut off  
Network Standby  
On Timer Function  
LED light setting  
DCR  
Off  
Select Baud rate using the  or  button. To set transmission  
speed RS232 or LD-NET communication for 19200 or 9600 Baud rate  
by pressing the  or  button.  
Off  
On  
Off  
Off  
Off  
Network initial  
Temperature Error  
IP Address  
>>>  
N Panel protection  
0
7RꢀSUHYHQWꢀLPDJHꢀVWLFNLQJꢀZKLFKꢀPD\ꢀRFFXUꢀVKRZLQJꢀVWLOOꢀSLFWXUHꢀIRUꢀDꢀ  
long time, select “Panel Protect” using the  or  button, once  
highlighted you can select ON or OFF by pressing the  or  
button.  
000000000000  
000000000000  
000000000000  
000000000000  
Subnet  
Gateway  
DNS  
MENU  
Exit  
Select  
Adjust  
N AV Auto shut off  
With no picture input signal to AV1, RGB, AV2(YPbPr), AV3, DVI,  
1HWZRUNꢇꢀVHWꢀWXUQVꢀRIIꢀDXWRPDWLFDOO\ꢆꢀ6HOHFWꢀ³$9ꢀ$XWRꢀ6KXWꢀ2II´ꢀXVLQJꢀ  
the  or  button, once highlighted you can select On or Off by  
pressing the  or  button.  
This LCD monitor allows you to set up the following:  
SETTING PROCEDURE  
1. Press and hold the GREEN button on the remote control for 5  
seconds. (Installation Mode will appear)  
N Network Standby  
<RXꢀFDQꢀVDYHꢀSRZHUꢀFRQVXPSWLRQꢀVHOHFWLQJꢀ³2II´ꢀDWꢀ1HWZRUNꢀ6WDQGE\ꢀ  
in Installation mode, both RS232C and LD-NET do not functional. To  
PDNHꢀWKHPꢀIXQFWLRQDOꢇꢀVHOHFWꢀ³21´ꢀLQꢀWKLVꢀPHQXꢆ  
2. Use the  or  button to highlight each option, use the  or  
 button to adjust each option. Press the MENU button to exit  
the mode.  
N On Timer Function  
N On Program  
You can save power consumption selecting “Off” at On Timer function  
in Installation mode. On Timer in Time menu does not functional. To  
PDNHꢀWKHPꢀIXQFWLRQDOꢇꢀVHOHFWꢀ³21´ꢀLQꢀWKLVꢀPHQXꢆ  
Select ON program using the  or  button, select the start up  
position using the  or  buttons.  
ꢁ2IIꢋ$9ꢃꢋ5*%ꢋ$9ꢊꢋ$9ꢈꢋ3&ꢋ'9,ꢀRUꢀ1HWZRUNꢅ  
N LED Light setting  
Select LED Light setting using the  or  button, once highlight-  
ed you can select On or Off by pressing the  or  button.  
N Max Volume  
Select Max volume using the  or  button, use the  or  
buttons to set the maximum volume required.  
N DCR  
N Winter mode  
The picture contrast improved while DCR is ON. Select DCR using  
the  or  button, once highlighted you can select On or Off by  
pressing the  or  button.  
This Function can be activated when the LCD monitor is used dur-  
LQJꢀFROGꢀWHPSHUDWXUHꢀFRQGLWLRQVꢇꢀDSSUR[LPDWHO\ꢀꢈꢌÛ)ꢋꢎÛ&ꢀRUꢀEHORZꢀWRꢀ  
maintain picture performance.  
Using the  or  button select winter mode, once highlighted you  
can select ON or OFF by pressing the  or  button.  
IMPORTANT: The AC cord should not be disconnected during the  
operation of Winter mode function.  
N Network Initial  
This function automatically installs the IP Address, Subnet, Gateway  
and DNS information.  
When in winter mode, power consumption is higher than normal  
standby consumption. This is entirely due to the operation of heating  
circuitry. We strongly recommend to turn off Winter mode when the  
DPELHQWꢀWHPSHUDWXUHꢀLVꢀDERYHꢀꢈꢌÛ)ꢋꢎÛ&ꢆ  
N Temperature Error  
The recorded number of abnormal temperature is occurred is indi-  
cated here.  
N RC inhibition  
You can prevent unwanted remote control operation by selecting RC  
N IP Address/Subnet/Gateway/DNS  
These 4 items display the LD-Net information. If LD-NET is NOT con-  
Inhibition.  
nected, all the items would be displayed as “000000000000”.  
Select using the  or  button. Press the  or  button to  
select On or Off.  
To re-instate RC operation press and hold the green button on the  
remote control and select RC inhibition OFF.  
Disconnecting the mains supply before exiting Installation Mode will  
cancel the following features On program, RC inhibition, Address  
and Baud Rate.  
N Child Lock  
You can prevent unwanted operation of the LCD monitor via the  
buttons on the rear of the monitor.  
Select using the  or  button. Press the  button to select  
2QꢀRUꢀ2))ꢀ7KHꢀ³&KLOGꢀ/RFN´ꢀ26'ꢀZLOOꢀDSSHDUꢀLIꢀEXWWRQVꢀDUHꢀSUHVVHGꢀ  
ZKHQꢀFKLOGꢀORFNꢀLVꢀ2Qꢆ  
6WDQGE\ꢀRSHUDWHVꢀQRUPDOO\ꢀZKHQꢀFKLOGORFNꢀLVꢀVHWꢀ³2Q´ꢆ  
11  
GB  
GB  
OPERATION  
6HOHFWLRQꢀRIꢀSLFWXUHꢀVL]H  
Select screen size from FULL, FULL ALL, ZOOM 16:9, TITLE IN 16:9,  
ZOOM 14:9, TITLE IN 14:9, NORMAL or NATURAL WIDE by pressing  
the WIDE button repeatedly on the Remote Control.  
When in AV2 (RGBHV) or PC mode FULL or NORMAL can be  
selected.  
Note: Full - Set display area 100%  
Only in DVI or AV2 (YPbPr) displaying high resolution content  
FULL and FULL ALL are selectable.  
Note: FULL - Set display area 95%  
FULL ALL - Set display area 100%  
All other inputs AV1, AV3, DVI or AV2 (YPbPr) (displaying lower reso-  
lutions) can select all picture sizes.  
N Full/Full All  
N Title In 14:9  
4:3  
14:9  
16:9  
Letterbox Video  
4:3  
14:9  
16:9  
Letterbox Video  
TITLES ON SCREEN  
TITLES ON SCREEN  
TITLES ON SCREEN  
TITLES ON SCREEN  
The whole screen The whole screen The whole screen 7KHꢀEODFNꢀEDUVꢀ  
As zoom (14:9),  
but bottom is  
As zoom (14:9),  
but bottom is  
As zoom (14:9),  
but bottom is  
As zoom (14:9),  
but bottom is  
LVꢀ¿OOHGꢀVWUHWFKLQJꢀ LVꢀ¿OOHGꢀVWUHWFKLQJꢀ LVꢀ¿OOHGꢀZLWKꢀWKHꢀ  
top and bottom  
are present and  
the height is  
the width.  
the height slightly corrrect picture  
compressed even compressed even compressed even compressed even  
at the edges.  
ratio.  
more to allow  
subtitles to be  
seen.  
more to allow  
subtitles to be  
seen.  
more to allow  
subtitles to be  
seen.  
more to allow  
subtitles to be  
seen.  
compressed.  
N Normal  
N Zoom 16:9  
4:3  
14:9  
16:9  
Letterbox Video  
4:3  
14:9  
16:9  
Letterbox Video  
The correct  
Zooms in slightly Zooms in slightly 7KHꢀEODFNꢀEDUVꢀ  
The correct ratio %ODFNꢀEDUVꢀ  
is maintained with left and right,  
EODFNꢀEDUVꢀRQꢀWKHꢀ picture height is  
%ODFNꢀEDUVꢀ  
%ODFNꢀEDUVꢀOHIWꢇꢀ  
right, top and  
bottom.  
picture width is  
maintained but  
the top and bot-  
tom are cropped.  
cropping the top  
and bottom.  
cropping the top  
and bottom.  
top and bottom  
are smaller and  
the picture height  
is compressed  
slightly.  
left and right,  
picture height is  
stretched.  
left and right.  
stretched.  
N Title in 16:9  
N Natural Wide  
4:3  
14:9  
16:9  
Letterbox Video  
4:3  
14:9  
16:9  
Letterbox Video  
TITLES ON SCREEN  
TITLES ON SCREEN  
TITLES ON SCREEN  
TITLES ON SCREEN  
As Zoom (16:9),  
but bottom is  
As Zoom (16:9),  
but bottom is  
As Zoom (16:9),  
but bottom is  
As Zoom (16:9),  
but bottom is  
Stretches the pic- The height is ex- 7KHꢀSLFWXUHꢀ¿OOVꢀ  
ture horizontally SDQGHGꢀWRꢀ¿OOꢀWKHꢀ the screen and  
7KHꢀEODFNꢀEDUVꢀ  
top and bottom  
remain and the  
height is com-  
SUHVVHGꢀWRꢀ¿WꢀWKHꢀ  
picture area.  
compressed even compressed even compressed even compressed even  
WRꢀ¿OOꢀWKHꢀVFUHHQꢆꢀ whole screen.  
The picture is  
is proportionally  
correct.  
more to allow  
subtitles to be  
seen.  
more to allow  
subtitles to be  
seen.  
more to allow  
subtitles to be  
seen.  
more to allow  
subtitles to be  
seen.  
more stretched at  
the edges.  
N Zoom 14:9  
4:3  
14:9  
16:9  
Letterbox Video  
The correct  
Zooms in slightly Zooms in slightly 7KHꢀEODFNꢀEDUVꢀ  
picture width is  
maintained but  
the top and bot-  
tom are cropped.  
cropping the top  
and bottom.  
cropping the top  
and bottom.  
top and bottom  
are smaller and  
the picture height  
is compressed  
slightly.  
12  
GB  
GB  
OPERATION  
PIP/POP Operation  
Using this function, you can enjoy a DVI or Network program and an  
image (AV1, AV2, AV3 or PC input) at the same time.  
Press the ON/OFF button on the Remote Control repeatly to select  
PIP1, PIP2, POP or OFF mode.  
During the PIP/POP mode, press the Main/Sub Picture Swap but-  
ton will switch the location for main and sub picture.  
Only the sound on the main picture is heard from the monitor  
VSHDNHUꢆꢀ7KHꢀVRXQGꢀRQꢀWKHꢀVXEꢂSLFWXUHꢀFDQQRWꢀEHꢀKHDUGꢆ  
The details for PIP/POP operation (eg,location for sub picture or  
input source for any picture,etc.), please refer to page 10.  
N PIP1 mode  
N PIP2 mode  
N OFF mode  
N POP mode  
The left picture is main picture, the right picture is sub picture.  
13  
GB  
GB  
OPERATION (IN TEXT MODE)  
Teletext Operation  
Text Cancel  
Teletext is only available via external sources.  
Teletext mode can be operated by the following buttons on the Re-  
mote Control.  
Press the TEXT CANCEL button in TEXT or MIX mode, the TV pic-  
ture appears on the screen.  
Press this button once again or press TXT/TV button, CANCEL mode  
will be cancelled.  
Some buttons have dual functions.  
In CANCEL mode, “CAN” is always displayed on the upper left of the  
screen.  
TXT/TV  
Press TXT/TV button to select teletext. Press again will display:  
AV mode: AV/TEXT mode/MIX mode/AV.  
Text Hold  
Press Text Hold button to stop page request and updating.  
Note:  
MIX mode: AV (broadcast image) screen and the contents of TEXT  
(superimposed) are displayed simultaneously.  
HOLD ON:  
The Hold symbol will appear instead of the page number.  
Update of TELETEXT is forbidden. It holds on the current TEXT  
screen display now.  
CANCEL mode: TEXT/MIX MODE is cancelled temporarily and AV  
image is displayed.  
HOLD OFF:  
If the signal is removed or disconnected, the monitor will revert to a  
EOXHꢀEDFNJURXQGꢀZLWKꢀ³1RꢀVLJQDO´ꢀPHVVDJHꢀRQꢀWKHꢀVFUHHQꢆ  
If the TXT/TV button is pressed during the CANCEL mode, the CAN-  
CEL mode will be cancelled, and full text will resume.  
The hold symbol is replaced with the page number.  
TELETEXT page data is updated.  
The present page is re-requested. (header roll)  
7H[Wꢀ+ROGꢀEXWWRQꢀZLOOꢀRQO\ꢀZRUNꢀZKLOVWꢀLQꢀ7(;7ꢀ0RGHꢆ  
Text Subcode  
Text Reveal  
Press this button, “110/. . . .” will be displayed (e.g. the current page is  
110).  
And press the NUMERIC buttons(0 ~ 9) to enter the sub page.  
For example, to select sub page 4, press NUMERIC buttons 0 - 0 - 0  
- 4, and “110/0004” will be displayed.  
Press Text Reveal button to reveal hidden items on the text page.  
Some pages such as quiz pages have the answers hidden. The button  
PD\ꢀKDYHꢀWRꢀEHꢀKHOGꢀWRꢀNHHSꢀWKHꢀDQVZHUꢀRQꢀWKHꢀVFUHHQꢇꢀRUꢀSUHVVꢀDJDLQꢀ  
to remove the answer.  
:KHQꢀ¿QLVKHGꢇꢀSUHVVꢀWKHꢀWH[WꢀVXEFRGHꢀEXWWRQꢀWRꢀUHWXUQꢀWRꢀQRUPDOꢀ  
operation.  
In Reveal OFF, this indication is not given.  
Text Reveal buttonꢀZLOOꢀRQO\ꢀZRUNꢀZKLOVWꢀLQꢀWH[WꢀPRGHꢆ  
Text Index  
Page Up and Down  
Press this button to select one of the teletext index pages in TEXT,  
MIX or CANCEL mode.  
To select the next or previous page.  
Volume Up/Down  
Text Red  
Use to select the red topic or page number at the bottom of the text  
page.  
To adjust the sound volume level.  
7H[Wꢀ6L]H  
Text Green  
Press Text Size button to enlarge the top half of the text page.  
Press Text Size button again to enlarge the bottom half of the text  
page.  
Use to select the green topic or page number at the bottom of the text  
page.  
Press Text Size button again to return to the normal size page.  
(Normal/top half enlargement/bottom half enlargement/normal)  
Text Yellow  
Note:  
During the top half or bottom half enlargement mode, if a page re-  
quest is performed by [0 ~ 9] numeric buttons or the TEXT INDEX  
button, it will return to normal mode and a page will be requested.  
If HOLD ON/OFF is performed during the top half enlargement mode,  
it will hold the top half enlargement mode. (HOLD symbol will display)  
If HOLD ON/OFF is performed during the bottom half enlargement  
mode, it will hold the bottom half enlargement mode. (HOLD symbol  
will NOT display)  
Use to select the yellow topic or page number at the bottom of the text  
page.  
Text Blue  
Use to select the blue topic or page number at the bottom of the text  
page.  
14  
GB  
GB  
SPECIFICATIONS/HELPFUL HINTS  
6SHFL¿FDWLRQ  
Helpful hints  
&RPPRQꢀVSHFL¿FDWLRQ  
N NO PICTURE NO SOUND  
L &KHFNꢀLIꢀPRQLWRUꢀLVꢀSOXJJHGꢀLQꢆ  
L &KHFNꢀPRQLWRUꢀLVꢀQRWꢀLQꢀVWDQGE\ꢀPRGHꢆ  
Power source: 100 ~ 240V 50Hz/60Hz  
Colour system: PAL/NTSC/NTSC4.43/SECAM  
AV terminal  
N POOR PICTURE  
AV1: Scart CENELEC Standard  
Input: Composite video, RGB (5V RGB with 5V sync to pin 14)  
and audio-L/R  
L Adjust BRIGHTNESS/CONTRAST levels (too low).  
Nꢀ12ꢀ&2/285ꢁꢀ3,&785(ꢀ2.  
L Adjust COLOUR control.  
Output: composite video from AV3 and audio L/R  
AV2: BNC  
Input: RGB, H and V/Y, Pb, Pr and audio L/R  
Output: RGB, H and V/Y, Pb, Pr  
L &KHFNꢀOHDGꢀFRQQHFWLRQVꢆ  
L Does the signal input have colour.  
AV3: BNC  
Input: Composite video  
Output: Composite video  
N REMOTE CONTROL DOES NOT WORK  
L &KHFNꢀEDWWHULHVꢀDUHꢀLQVHUWHGꢀFRUUHFWO\ꢆ  
L &KHFNꢀFRQGLWLRQꢀRIꢀEDWWHULHVꢆ  
Audio Monitor Out: CINCH L/R  
Audio Speaker Out: 2 x 6W  
L &KHFNꢀWRꢀVHHꢀLIꢀUHPRWHꢀFRQWUROꢀLQKLELWꢀLVꢀVHWꢀ21ꢆ  
DVI  
Nꢀ3,&785(ꢀ2.ꢁꢀ12ꢀ6281'  
Input: DVI-D GROUP Standard  
L &KHFNꢀH[WHUQDOꢀVSHDNHUVꢀDUHꢀFRQQHFWHGꢀFRUUHFWO\ꢆ  
L &KHFNꢀOHDGꢀFRQQHFWLRQVꢀWRꢀH[WHUQDOꢀHTXLSPHQWꢆ  
L &KHFNꢀYROXPHꢀWXUQHGꢀGRZQꢀRUꢀPXWHꢀVHOHFWHGꢆ  
PC  
Input:ꢀ0LQLꢀ'ꢂ68%ꢀꢃꢄꢀ3,1ꢀDQGꢀ$XGLRꢀꢈꢆꢄPPꢀ-DFN  
Serial Port: RS232C: Input/Output  
Net Organiser: POA-LN02 (optional)  
When ordering these products, give the Name and Type No. to the  
sales dealer.  
Screen  
(inches/cm)  
(viewing measured  
diagonally)  
Display Native  
Resolution  
Dimension  
Veiwing angles  
Model name  
Contrast Ratio  
Weight (kg)  
(W x H x D)  
CE42LH2R  
32.8  
33.8  
37.5  
1027 x 620 x 178.5 mm  
H: 178°, V: 178°  
CE42LH2DPB  
CE42LH2WP  
1000:1  
42"/106.7 cm  
1920 x 1080  
1027 x 620 x 183 mm  
L 7KHꢀVSHFL¿FDWLRQVꢀDUHꢀVXEMHFWꢀWRꢀFKDQJHꢀZLWKRXWꢀQRWLFHꢆ  
L LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a tiny fraction of the pixels  
(0.01% or less) may be ineffective by the characteristics of the LCD panels.  
15  
GB  
GB  
DIMENSIONS  
N CE42LH2WP  
Unit: mm  
989.0  
925.4  
(WALL MOUNT SCREW)  
10 x M6, 1.0 PITCH x 12MM  
418.4  
418.4  
41.8  
1027.0  
165.9  
126.0  
400.0  
953.0  
930.25  
VIEWING AREA(H)  
200.0  
100.0  
50.8  
17.6  
Handles x 2  
178.5  
402.9  
417.9  
Control buttons  
43.7  
ø4.2  
Cables exit terminal cover  
(RC RECEIVER)  
ø4.2  
(LED INDICATOR)  
16  
GB  
GB  
PC/DVI-D/COMPONENT SIGNAL SUPPORT TIMING LIST  
N PC signal support timing  
N DVI-D signal support timing  
+RUL]RQWDOꢀ  
Vertical  
+RUL]RQWDOꢀ  
Vertical  
Resolution Frequency Frequency  
Remark  
Resolution Frequency Frequency  
Remark  
ꢅN+]ꢇ  
31.47  
31.43  
37.50  
37.86  
43.27  
35.00  
34.97  
35.16  
37.88  
46.875  
34.50  
38.00  
53.67  
49.72  
48.36  
56.47  
60.02  
48.50  
60.31  
61.00  
68.68  
60.24  
37.5  
ꢅ+]ꢇ  
70.09  
59.88  
75.00  
72.81  
85.00  
66.67  
66.60  
56.25  
60.32  
75.00  
55.38  
60.51  
85.06  
74.55  
60.00  
70.07  
75.03  
60.02  
74.92  
75.70  
85.00  
75.08  
50.00  
60.00  
75.025  
60.01  
59.98  
60.01  
60.18  
60.00  
76.107  
65.20  
66.00  
75.60  
60.12  
59.90  
75.06  
75.00  
60.00  
60.01  
60.03  
50.00  
60.00  
ꢅN+]ꢇ  
31.43  
37.86  
37.5  
ꢅ+]ꢇ  
59.88  
72.81  
75  
720 x 400  
640 x 480  
DOS (VGA)  
VGA VESA 60Hz  
VGA VESA 75Hz  
VGA VESA 72Hz  
VGA VESA 85Hz  
Mac. 13  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
800 x 600  
832 x 624  
VGA VESA 60Hz  
VGA VESA 72Hz  
VGA VESA 75Hz  
MAC LC 13"  
640 x 480  
640 x 480  
34.97  
35  
66.6  
66.67  
56.25  
60.32  
75  
640 x 480  
MAC_NORMAL 13"  
SVGA VESA 56Hz  
SVGA VESA 60Hz  
SVGA VESA 75Hz  
MAC_NORMAL 16"  
XGA VESA 60Hz  
XGA VESA 75Hz  
XGA VESA 70Hz  
MAC_NORMAL 19"  
MAC_NORMAL 21"  
SXGA VESA 60Hz  
480p  
640 x 480  
35.16  
37.88  
46.875  
49.72  
48.36  
60.23  
56.47  
60.24  
68.68  
63.98  
31.7  
640 x 480  
Mac LC 13"  
SVGA VESA 56Hz  
SVGA VESA 60Hz  
SVGA VESA 75Hz  
SVGA  
800 x 600  
800 x 600  
74.55  
60  
800 x 600  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1152 x 870  
1280 x 1024  
720 x 480  
800 x 600  
75.03  
70.07  
75.08  
75.06  
60.02  
59.94  
59.94  
50  
800 x 600  
SVGA  
800 x 600  
SVGA VESA 85Hz  
Mac. 16  
832 x 624  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1280 x 720  
1280 x 960  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1152 x 900  
1152 x 900  
1152 x 900  
1400 x 1050  
1400 x 1050  
1152 x 870  
1280 x 1024  
1600 x 1200  
1366 x 768  
1360 x 768  
1920 x 1080  
1920 x 1080  
XGA VESA 60Hz  
XGA VESA 70Hz  
XGA VESA 75Hz  
XGA  
720 x 480  
15.73  
31.25  
15.63  
37.5  
480i  
768 x 575  
575p  
XGA  
768 x 575  
50  
575i  
XGA  
1280 x 720  
1280 x 720  
1366 x 768  
1360 x 768  
1920 x 1080  
1920 x 1080  
1920 x 1080  
1920 x 1080  
1920 x 1080  
1920 x 1080  
1920 x 1080  
50  
720p - 50Hz  
XGA VESA 85Hz  
MAC_Normal 19"  
720p - 50Hz  
SXGA VESA 60Hz  
SXGA VESA 75Hz  
SXGA  
45  
60  
720p - 60Hz  
48.36  
47.7  
60  
WXGA  
60  
WXGA  
60.00  
79.976  
63.370  
63.34  
63.74  
63.79  
63.90  
81.13  
61.20  
61.85  
71.40  
65.35  
65.12  
68.68  
80.00  
75.00  
48.36  
47.73  
28.125  
33.75  
28.125  
33.75  
56.25  
67.5  
50  
1080i - 50Hz  
60  
1080i - 60Hz  
50  
HDTV 1080p - 50Hz  
HDTV 1080p - 60Hz  
HDTV 1080p - 24Hz  
HDTV 1080p - 25Hz  
HDTV 1080p - 30Hz  
SXGA  
60  
SXGA  
27.00  
28.13  
33.75  
24  
SXGA  
25  
SXGA  
30  
SXGA  
Depending on the condition of signals and the type and length of cables, these  
signals may not be properly viewed.  
To save the XGA Mode 1366 x 768 setting switch the monitor off then on using  
the standby button.  
SXGA  
SXGA  
SXGA  
SXGA +  
SXGA +  
MAC_Normal 21"  
Mac II  
UXGA VESA 60Hz  
WXGA  
WXGA  
1080i - 50Hz  
1080i - 60Hz  
The monitor can be automatically adjusted in pc mode when receiving a stan-  
dard VESA signal. It will be displayed as XGA when the monitor is receiving a  
XGA or WXGA signal.  
N Component signal support timing  
+RUL]RQWDOꢀ  
Vertical  
Resolution Frequency Frequency  
Remark  
ꢅN+]ꢇ  
15.735  
15.625  
31.25  
31.25  
45.00  
37.50  
33.75  
28.13  
ꢅ+]ꢇ  
60i  
720 x 480  
720 x 576  
SDTV 480i  
SDTV 576i  
SDTV 480p  
SDTV 576p  
HDTV 720p  
HDTV 720p  
HDTV 1080i  
HDTV 1080i  
50i  
720 x 480  
60p  
50p  
60p  
50p  
60i  
720 x 576  
1280 x 720  
1280 x 720  
1920 x 1080  
1920 x 1080  
50i  
17  
GB  
GB  
RS232C COMMAND TABLES  
N Functional Execution Command Table  
Command Item  
N Image control Read Command Table  
Status read command  
Item  
Status of Brightness.  
C00  
C01  
C03  
C10  
C22  
C24  
C25  
C26  
C27  
C28  
C29  
C30  
C0F  
C70  
C71  
C72  
C73  
C74  
C75  
C76  
C64  
C92  
POWER ON  
CR BRIGHT  
CR CONT  
CR COLOR  
CR TINT  
POWER OFF  
Status of Contrast.  
Status of Color.  
Status of Tint.  
Sharpness.  
POWER ON/ OFF (toggle)  
Wide toggle  
Input  
CR SHARP  
Wide “Natural” direct  
Wide “Zoom 16:9” direct  
Wide “Title in 16:9” direct  
Wide “Zoom 14:9” direct  
Wide “Title in 14:9” direct  
Wide “Full” direct  
Picture  
Status of White Balance Mode informa-  
tion.  
CR WBAL  
CR WBAL-R  
CR WBAL-G  
CR WBAL-B  
CR NZRED  
CR FILM  
Status of White Balance Red.  
Status of White Balance Green.  
Status of White Balance Blue.  
Status of Noise reduction setting.  
Status of Film mode setting.  
Status of Image selection.  
(The same as PICTURE mode)  
CR IMAGE  
Wide “Normal” direct  
AV1 direct  
CR DCDI  
Status of DCDi setting.  
RGB direct  
CR ACCACM  
CR CCS  
Status of ACC/ACM setting.  
Status of CCS setting.  
AV2 RGBHV direct  
AV2 YPbPr direct  
AV3 direct  
CR MPEGNR  
Status of MPEG NR setting.  
DVI direct  
PC direct  
N PC Read Command Table  
PC Auto adjust  
Factory settings  
Power save ON  
Power save OFF  
&KLOGꢀORFNꢀ21  
Status read command  
Item  
CR H-POS  
CR V-POS  
CR PHASE  
CR CLOCK  
Status of Horizontal position.  
Status of Vertical position.  
Status of PHASE value.  
Status of CLOCK value.  
CF PSAVE ON  
CF PSAVE OFF  
CF CLOK ON  
CF CLOK OFF  
CF DEA RMCY  
CF DEA RMCN  
&KLOGꢀORFNꢀ2))  
RC inhibition OFF  
RC inhibition ON  
N Input Read Command Table  
Status read command  
Item  
CR INPUT  
Status of Input selection.  
CR SOURCE  
CR SYSTEM  
Status of Input source mode.  
Status of system of Input mode.  
N Screen Read Command Table  
Status read command  
Item  
Status of screen size.  
(The same of WIDE mode)  
CR SCREEN  
18  
GB  
GB  
RS232C COMMAND TABLES  
N Time Read Command Table  
N UK5 Read Command Table (Basic Command)  
Status read command  
Item  
Command  
CR0  
Item  
Note  
Status of accumulated lifetime of panel.  
(The same as CR_LAMPH Command)  
Power  
On, Standby, power error,  
AV1, AV2, . . . , DVI, PC  
Auto, Normal, Full, . . .  
Dynamic, Standard, . . .  
Signal/No signal  
On/Off  
CR PANELH  
CR MONH  
CR1  
Input Mode  
Wide mode  
Status of accumulated lifetime of monitor.  
ꢁ7KHꢀVDPHꢀDVꢀ&5B352-+ꢀ&RPPDQGꢅ  
CR WIDE  
CR PICTURE Picture mode  
CR SIGNAL  
CR CHILD  
CR PSAVE  
CRTM  
Signal existence  
&KLOGꢀORFN  
N Sound control Read Command Table  
Power save  
On/Off  
Status read command  
CR VOLUME  
Item  
Panel usage time  
RC inhibition  
Model number  
–––  
Status of volume value.  
Status of MUTE.  
CR RMC  
CR MDL  
On/Off  
CR MUTE  
Model number  
N Setting Read Command Table  
N Error code Table  
Status read command  
Item  
Error code  
Note  
CR LANG  
CR P-MANE  
CR TILE  
Status of Language selection.  
• Receiving the data that cannot be decoded.  
• The wrong indication of parameter.  
ꢁ:URQJꢀ¿JXUHGꢀQXPEHUꢇꢀRUꢀZURQJꢀZRUGꢀLVꢀLQFOXGHGꢅ  
?
Status of Power management setting.  
Status of Tile mode ON/OFF setting.  
000  
102  
Normal receiving. (no error)  
Status of Tile mode, the number of  
Horizontal array.  
CR TILE-HSETS  
CR TILE-VSETS  
CR TILE-HLOCAT  
CR TILE-VLOCAT  
&5ꢀ7,/(ꢂ%=/+$'-  
&5ꢀ7,/(ꢂ%=/9$'-  
If the command of out of range is directly entered  
valuable parameter.  
Status of Tile mode, the number of  
Vertical array.  
No matching with Hardware.  
(Command for optional function which is not  
equipped)  
103  
Status of Tile mode, the number of  
Horizontal allocation.  
If the command of “Out of range” is entered by  
inclement or decrements by numeric value.  
201  
301  
Status of Tile mode the number of Verti-  
cal allocation.  
While capturing the picture, no execution. Wait and  
transmit command again.  
Status of Tile mode, the width of bezel  
(Horizontal).  
While PIN code is in operation, no execution.  
Wait and transmit command again.  
402  
101  
Status of Tile mode, the width of bezel  
(Vertical).  
The errors not including above.  
CR ONPROG  
Status of On Program information.  
Status of Winter mode Information.  
Statuses of Panel protect Information.  
Status of LED light Information.  
CR WINTERMODE  
CR PANELPROTECT  
CR LEDLIGHT  
CR AVAUTOSHUT  
CR CHILDLOCK  
CR RCINHIBITION  
Status of AV auto shut OFF Information.  
6WDWXVHVꢀRIꢀ&KLOGꢀORFNꢀ,QIRUPDWLRQꢆ  
Status of RC Inhibit Information.  
N Other Read Command Table  
Status read command  
Item  
CR STATUS  
CR SIGNAL  
CR FREEZE  
CR FANLOCK  
CR TEMP  
Status of the operation of the monitor.  
Status of with or without signal.  
Status of Freeze setting.  
6WDWXVHVꢀRIꢀIDQꢀORFNꢀHUURUꢆ  
Status of current temperature value.  
19  
N7RAK/ N7RBK/ N7RPK  
6$1<2ꢀ(OHFWULFꢀ&Rꢂꢁꢀ/WGꢂ  
INSTALLATION GUIDELINES  
CONSIGNES D’INSTALLATION  
INSTRUCCIONES DE INSTALACIÓN  
INSTALLATIONSRICHTLINIEN  
INSTALLATIEHANDLEIDING  
ISTRUZIONI DI INSTALLAZIONE  
CE42LH2WP  
CE42LM6WP  
CE42SR2  
CE52LH2WP  
CE52SR2  
CE52SR3  
IMPORTANT  
PLEASE READ THESE GUIDE LINES PRIOR TO UNPACKING  
AND INSTALLATION.  
IMPORTANT  
VEUILLEZ LIRE ATTENTIVEMENT CES CONSIGNES AVANT  
DE DEBALLER ET D’INSTALLER LE MONITEUR.  
¡IMPORTANTE!  
POR FAVOR, LEA ESTAS INSTRUCCIONES ANTES DE  
PROCEDER AL DESEMBALAJE Y LA INSTALACIÓN.  
WICHTIG  
BITTE LESEN SIE DIESE RICHTLINIEN VOR DEM  
AUSPACKEN UND DER INSTALLATION.  
BELANGRIJK  
LEES DEZE HANDLEIDING VOOR HET UITPAKKEN EN  
INSTALLEREN.  
IMPORTANTE  
LEGGERE ATTENTAMENTE LE SEGUENTI ISTRUZIONI  
PRIMA DI DISIMBALLARE E INSTALLARE IL PRODOTTO.  
English  
IMPORTANT!!  
To All Installers,  
This monitor is sealed to IP66 standard. The integrity of  
the enclosure MUST NOT be tampered with or breached.  
The following guide lines highlight those areas of the  
product that require particular care and attention in order  
to ensure the integrity of the enclosure.  
REMOVAL FROM OUTER CARTON  
• We strongly advise that 2 ~ 4 PEOPLE handle the monitor when removing it from the carton.  
Dropping or bumping the monitor during unpacking can result in damage to the sets integrity and  
appearance.  
• Please ensure carton top is facing upwards before removing monitor.  
‡ꢀ%HIRUHꢀUHPRYLQJꢀPRQLWRUꢀIURPꢀFDUWRQꢁꢀZHꢀUHFRPPHQGꢀWKDWꢀWKHꢀPRXQWLQJꢀEUDFNHWꢀLVꢀDWWDFKHGꢀÀUVWꢀWRꢀ  
avoid any damage during installation.  
• Please ensure that both installers grip the monitor as shown in photos below.  
To lift and maneuver the monitor, please use the handles provided and support from underside as  
illustrated in picture.  
IT IS STRONGLY RECOMMENDED  
TO HANDLE BY 2 ~ 4 PEOPLE.  
Always use the handles to lift the set  
ALWAYS SUPPORT THE MONITOR FROM UNDERNEATH  
2
BACK OF MONITOR  
LD-NET COVER  
SECURITY FIXING POINT  
(42 inch model only)  
TERMINAL COVER  
MAINS LEAD  
* This photo is 42 inch model.  
WEATHERPROOF ENCLOSURE VENTILATION  
• There are labels to inform users that the vents MUST NOT be loosened or removed otherwise the  
sealing of the set will be compromised. Adhesive applied to the vent threads provides added seal  
security and a visual indication of tampering. In the event that this adhesive sealing is broken when  
the set is returned, SANYO can not accept liability for the condition.  
• Vent caps can be easily damaged. The set should always be lifted (DO NOT SLIDE) and always  
PDNHꢀXVHꢀRIꢀUDLVHGꢀFXVKLRQVꢀXQGHUꢀWKHꢀDOXPLQLXPꢀIUDPHꢀLIꢀSODFHGꢀÁDWꢀRQꢀUHDUꢀVLGHꢂ  
• The vents SHOULD NOT be covered or obstructed.  
Please note that caps are easily damaged.  
Do not lay monitor with rear side down without proper protection underneath.  
EXAMPLE OF VENT  
CAP MISSING  
3
ANTI-TAMPER INK  
• Anti-tamper ink has been placed on the screws on the back plate, AV insert and outer back  
cabinet.  
• This is to identify if the screws have been removed. Any attempt to remove the anti-tamper ink will  
be CLEARLY visible.  
• In the event that the back plate is removed, the sealing of the set will be compromised, therefore,  
SANYO can not accept liability for any related failure.  
ANTI-TAMPER INK  
SCREWS  
‡ꢀ$OOꢀEDFNꢀSODWHꢀÀ[LQJꢀVFUHZVꢀXWLOLVHꢀUXEEHUꢀVHDOLQJꢀZDVK-  
HUVꢂꢀ7KLVꢀLPSURYHVꢀWKHꢀDLUꢀWLJKWꢀLQWHJULW\ꢀRIꢀWKHꢀÀ[LQJꢀDQGꢀ  
therefore MUST NOT be removed.  
‡ꢀ2QO\ꢀZDOOꢀPRXQWꢀÀ[LQJꢀDQGꢀWHUPLQDOꢀFRYHUꢀVFUHZVꢀPD\ꢀ  
be removed by the installer. Under no circumstances  
should non-SANYO screws be used as replacements.  
RUBBER WASHER  
SECURITY FIXING POINT (42 inch model only)  
‡ꢀ$ꢀVHFXULW\ꢀÀ[LQJꢀSRLQWꢀLVꢀSURYLGHGꢀRQꢀWKHꢀEDFNꢀSODWHꢀLQꢀ  
order to secure the monitor to the installation point with  
a security device.  
• This is NOT for lifting purposes. Lifting the monitor by  
WKHꢀVHFXULW\ꢀÀ[LQJꢀSRLQWꢀZLOOꢀFDXVHꢀGHIRUPDWLRQꢀRIꢀWKHꢀ  
back plate, resulting in possible breakdown of the weath-  
erproof seal.  
4
REAR A.V.SHIELD COVER/TERMINAL COVER  
‡ꢀ$IWHUꢀFDEOHꢀLQVWDOODWLRQꢀ3/($6(ꢀHQVXUHꢀDOOꢀVHDOVꢀDUHꢀFRUUHFWO\ꢀÀWWHGꢀDVꢀVKRZQꢀEHORZꢀSULRUꢀWRꢀUHÀW-  
ting the terminal cover and rear A.V.cover. ALLꢀÀ[LQJꢀVFUHZVꢀPXVWꢀEHꢀUHSODFHGꢀDQGꢀWLJKWHQHGꢂ  
Check point  
Check point  
1
2
Check gasket is in place inside the cover. &DEOHVꢀPXVWꢀÀWꢀLQꢀWKHꢀVKDSHꢀRIꢀWKHꢀ  
Gasket is important to seal cable area.  
recess of the terminal base.  
MAKE SURE CORD FITS IN  
THE MOULD SHAPE  
GASKET IN THE TERMINAL  
COVER  
GASKET IN THE RECESS  
OF THE TERMINAL BASE  
5
MAINS LEAD  
• The mains lead is secured to the back plate using a weatherproof cable gland.  
Do not loosen the gland as this will impair the weatherproof sealing.  
RUBBER WASHER  
VIEW INSIDE ENCLOSURE  
ADHESIVE TREATMENT  
‡ꢀ7KHꢀFDELQHWꢀFRUQHUVꢀDUHꢀVHDOHGꢀXVLQJꢀDꢀVSHFLDOꢀDGKHVLYHꢀWRꢀPD[LPLVHꢀWKHꢀVHDOꢂ  
• Sets must be handled with EXTREME care to ensure that this seal is not damaged. Please take  
particular care not to drop or bump the set during handling/installation.  
COATING MATERIAL  
• The steel back plate is protected from corrosion using a polyester powder coating. Good care and  
attention must be taken to prevent scratching the surface. Any uncoated metal will corrode poten-  
tially affecting the integrity of the enclosure.  
• Similarly the same care and attention applies to the aluminum enclosure which is anodised to pro-  
tect it from corrosion.  
CAUSE RUST!!  
6
INSTALLING POSITION  
When the monitor installed outside, it SHOULD NOT set  
in a position where the screen is subjected to direct sun  
light.  
If it can’t be done, please prepare adequate shading. Di-  
rect sun light can cause the screen surface temperature  
WRꢀULVHꢀDERYHꢀWKHꢀPD[LPXPꢀRSHUDWLQJꢀUDQJHꢂꢀ  
This causes a black shadow to appear on the screen,  
which will disappear when the screen temperature returns  
WRꢀZLWKLQꢀVSHFLÀFDWLRQꢂ  
WIRE ASSEMBLY  
1. Connect the in-line waterproof AC cord, line up and push together connectors A & B so they are  
tight and then twist C until A & B cannot be pulled apart. To disconnect unscrew C and pull con-  
nector A & B apart.  
To Connect  
To Disconnect  
C
B
A
C
A
B
2. Remove the covers A for access to connect required cables. Re-position the covers and replace  
screws.  
If LD Net connection is required remove cover B and connect cable, then re-position cover B and  
replace screws.  
B
B
A
A
DO NOT REMOVE SILICA GEL SACHETS FROM INSIDE LD-NET TERMINAL COVER (B)  
AND TERMINAL COVER (A).  
Thank you for your attention.  
We hope our Weatherproof monitors are to your satisfaction.  
7
GB  
GB  
SAFETY PRECAUTIONS  
CAUTION: Please read and retain for your safety. This unit has been designed and manufactured to assure your personal safety, but  
LPSURSHUꢀXVHꢀFDQꢀUHVXOWꢀLQꢀSRWHQWLDOꢀHOHFWULFꢀVKRFNꢀRUꢀÀUHꢀKD]DUGVꢂꢀ,QꢀRUGHUꢀQRWꢀWRꢀGHIHDWꢀWKHꢀVDIHJXDUGVꢀLQFRUSRUDWHGꢀLQꢀWKLVꢀPRQLWRUꢀREVHUYHꢀWKHꢀ  
following basic rules for its installation, use and servicing.  
The operating temperature range of this monitor is guaranteed 0°C  
Installation and Use  
~ 40°C/32°F ~ 104°F. It is not recommended to install the screen  
in direct sunlight without adequate shading, as this will cause the  
WHPSHUDWXUHꢀRIꢀWKHꢀSDQHOꢀWRꢀULVHꢀDERYHꢀWKHꢀPD[LPXPꢀVSHFLÀHGꢂꢀ  
Doing so may cause a black shadow to appear on the screen which  
will disappear when the screen temperature returns to within the  
VSHFLÀFDWLRQꢂꢀ7KLVꢀ´RIꢀFRXUVHµꢀGRHVꢀQRWꢀSURGXFHꢀDQ\ꢀKDUPIXOꢀHIIHFWꢀRQꢀ  
the lifetime of the monitor.  
Do not allow anything to rest on the power  
cord. Do not locate this LCD monitor where the  
cord will be damaged by people walking on it.  
Do not RYHUORDGꢀZDOOꢀRXWOHWVꢀDQGꢀH[WHQVLRQꢀ  
FRUGVꢀDVꢀWKLVꢀFDQꢀUHVXOWꢀLQꢀÀUHꢀRUꢀHOHFWULFꢀVKRFNꢂ  
A suitable socket outlet must be provided near  
Do not apply liquid cleaners or aerosol cleaners directly onto the LCD  
to the monitor and shall be easily accessible.  
monitor. Use a damp cloth for cleaning.  
Do not place this LCD monitor near any heat  
sources such as radiators, heaters, stoves and other heat-generating  
SURGXFWVꢀꢃLQFOXGLQJꢀDPSOLÀHUVꢄꢂꢀ  
ADDITIONAL FOR NORTH AMERICA AND CANADA:  
This monitor must NOT be permanently mounted to the building  
structure. It must be mounted in such a way that it can be removed  
using basic tools.  
Do not place your LCD monitor on an unstable stand, shelf or table.  
Serious injury to an individual, and damage to the LCD monitor may  
result if it should fall. Your sales person can recommend an approved  
wall mounting kit. A special wall mounting kit is available for this  
model.  
The power supply cord must NOT be attached to the building surface.  
The power supply cord must NOT be routed through walls, ceiling,  
ÁRRUVꢁꢀRUꢀRWKHUꢀVLPLODUꢀRSHQLQJVꢀLQꢀWKHꢀEXLOGLQJꢀVWUXFWXUHꢂꢀ  
The power supply cord MUST be positioned so as to prevent physical  
damage.  
This LCD monitor should be operated only from the type of power  
source indicated on the monitor or as indicated in the Operating In-  
structions. If you are not sure of the type of power supply, consult your  
sales person or your local power company.  
Important: (UK only)  
For added protection it is strongly recommended that this LCD  
monitor has its mains supplied via an approved earth fault protection  
device.  
THIS PRODUCT MUST BE EARTHED.  
7KLVꢀHTXLSPHQWꢀLVꢀÀWWHGꢀZLWKꢀDQꢀDSSURYHGꢀPDLQVꢀOHDGꢀDQGꢀDQꢀ  
approved non rewireable UK mains plug. To change a fuse in this  
type of plug proceed as follows:  
WARNING: To prevent injury the LCD monitor must be securely  
attached to the wall in accordance with the manufacturers installation  
instructions.  
1. Remove the fuse cover and fuse.  
2. Fit a new fuse which should be a BS1362 13 Amp A.S.T.A. or  
BSI approved type.  
IMPORTANT:  
3.ꢀ(QVXUHꢀWKDWꢀWKHꢀIXVHꢀFRYHUꢀLVꢀFRUUHFWO\ꢀUHÀWWHGꢂ  
This product must be earthed.  
This unit is not disconnected from the mains unless the mains lead  
is unplugged. The installer must make sure that the waterproof inline  
coupler is easily accessible.  
If the fuse cover is lost or damaged the plug must NOT be used  
but replaced with a serviceable plug.  
,IꢀWKHꢀÀWWHGꢀSOXJꢀLVꢀQRWꢀVXLWDEOHꢀIRUꢀ\RXUꢀVRFNHWꢀRXWOHWVꢁꢀLWꢀVKRXOGꢀ  
EHꢀFXWꢀRIIꢀDQGꢀDQꢀDSSURSULDWHꢀSOXJꢀÀWWHGꢀLQꢀLWVꢀSODFHꢂꢀ,IꢀWKHꢀPDLQVꢀ  
plug contains a fuse, this should have a rating of 13 Amp, ensure  
WKHꢀIXVHꢀFRYHUꢀLVꢀFRUUHFWO\ꢀÀWWHGꢂꢀ,IꢀDꢀSOXJꢀZLWKRXWꢀDꢀIXVHꢀLVꢀXVHGꢁꢀ  
the fuse at the distribution board should not be greater than 13  
Amp.  
This monitor is tested to IP66 standard rating.  
This monitor is not protected against temporary or continuous  
immersion in liquid.  
Do not use immediately after moving the LCD monitor from a low  
temperature to a high temperature environment, as this causes con-  
GHQVDWLRQꢁꢀZKLFKꢀPD\ꢀUHVXOWꢀLQꢀÀUHꢁꢀHOHFWULFꢀVKRFNꢁꢀRUꢀRWKHUꢀKD]DUGVꢂꢀ  
Before cleaning, unplug the monitor from the wall socket.  
Note: The severed plug must be destroyed to avoid a possible  
VKRFNꢀKD]DUGꢀVKRXOGꢀLWꢀEHꢀLQVHUWHGꢀLQWRꢀDꢀꢅꢆꢀ$PSꢀVRFNHWꢀHOVH-  
where.  
Do notꢀPRXQWꢀQHDUꢀDQꢀRSHQꢀÁDPHꢀVRXUFHꢂꢀ2SHQꢀÁDPHVꢀPXVWꢀQHYHUꢀ  
be used near this LCD monitor.  
The wires in this mains lead are coloured in accordance with the  
following code:  
This LCD monitor should not be built in or enclosed in any way, heat  
build up will reduce the life of the monitor.  
Blue  
Neutral  
Live  
Brown  
This LCD monitor should have a minimum distance of 5cm away from  
Green and Yellow  
Earth  
the wall and the monitor should have 10cm distance around the top  
1. The Blue wire must be connected to the terminal which is  
and sides.  
PDUNHGꢀZLWKꢀWKHꢀOHWWHUꢀ´1µꢀRUꢀFRORXUHGꢀ%/$&.ꢂ  
AlwaysꢀPRXQWꢀXVLQJꢀUHFRPPHQGHGꢀDQGꢀVXEVWDQWLDOꢀÀ[WXUHVꢀDQGꢀÀW-  
2. The Brown wire must be connected to the terminal with the  
tings.  
OHWWHUꢀ´/µꢀRUꢀFRORXUHGꢀ5('ꢂ  
10cm  
3. The Green and Yellow wire must be connected to the termi-  
QDOꢀZKLFKꢀLVꢀPDUNHGꢀZLWKꢀWKHꢀOHWWHUꢀ´(µꢀRUꢀFRORXUHGꢀ*5((1ꢀRUꢀ  
GREEN and YELLOW.  
5cm  
10cm  
10cm  
Before replacing the plug cover, make certain that the cord grip is  
clamped over the sheath of the lead - not simply over the wires.  
Do not attempt to bypass the safety purpose of the grounding  
type plug.  
7KHꢀUHDUꢀÀQQHGꢀVHFWLRQꢀDURXQGꢀWKHꢀFDELQHWꢀIXQFWLRQVꢀDVꢀDꢀKHDWꢀVLQNꢁꢀ  
UHPRYLQJꢀKHDWꢀDZD\ꢀIURPꢀWKHꢀPRQLWRUꢂꢀ7KHꢀH[WHUQDOꢀVXUIDFHꢀRIꢀWKHꢀ  
FDELQHWꢀꢃÀQQHGꢀDUHDꢄꢀPXVWꢀQRWꢀEHꢀFRYHUHGꢀRUꢀWKHꢀDLUÁRZꢀUHVWULFWHGꢀLQꢀ  
anyway by enclosing the LCD monitor.  
THIS UNIT IS NOT DISCONNECTED FROM THE MAINS UN-  
LESS THE MAINS LEAD IS UNPLUGGED.  
THE INSTALLER MUST MAKE SURE THE MAINS LEAD IS  
EASILY ACCESSIBLE.  
8
GB  
GB  
SERVICING  
Servicing  
Your monitor is fully transistorised and does not contain any user serviceable components.  
You must not remove the rear cover of the monitor by yourself. The apparatus is working with high voltages and could damage  
objects or even endanger people. Leave all required repair and service jobs to an authorised service technician. He will exclusively  
use such spare parts that are complying with the same safety standards as applicable to the original parts. The use of original spare  
SDUWVꢀFDQꢀSUHYHQWꢀÀUHꢁꢀVKRFNꢀDQGꢀRWKHUꢀKD]DUGVꢂ  
8QSOXJꢀWKHꢀ/&'ꢀPRQLWRUꢀIURPꢀWKHꢀZDOOꢀRXWOHWꢀDQGꢀUHIHUꢀVHUYLFLQJꢀWRꢀTXDOLÀHGꢀVHUYLFHꢀSHUVRQQHOꢀXQGHUꢀWKHꢀIROORZLQJꢀ  
conditions:  
N If the power cord or plug is damaged.  
N If liquid has been spilt in to the LCD monitor.  
N If the LCD monitor has been dropped or the cabinet has been damaged.  
N ,IꢀWKHꢀ/&'ꢀPRQLWRUꢀH[KLELWVꢀDꢀGLVWLQFWꢀFKDQJHꢀLQꢀSHUIRUPDQFHꢂ  
N If the LCD monitor does not operate normally by following the operating instructions.  
Adjust only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage.  
7KLVꢀZLOOꢀRIWHQꢀUHTXLUHꢀH[WHQVLYHꢀZRUNꢀE\ꢀDꢀTXDOLÀHGꢀWHFKQLFLDQꢀWRꢀUHVWRUHꢀWKHꢀPRQLWRUꢀWRꢀQRUPDOꢀRSHUDWLRQꢂ  
Important recycling information.  
Your SANYO product is designed and manufactured with high quality materials and components  
which can be recycled and reused.  
This symbol means that electrical and electronic equipment, at their end-of-life, should be dis-  
posed of separately.  
In the European Union there are separate collection systems for used electrical and electronic  
products.  
Please help us to conserve the environment we live in!  
Note: This symbol mark and recycle system are applied only to EU countries are not applied to  
other countries of the world.  
Federal Communications Commission Notice  
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits  
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This  
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,  
may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interfer-  
HQFHꢀLQꢀZKLFKꢀFDVHꢀWKHꢀXVHUꢀZLOOꢀEHꢀUHTXLUHGꢀWRꢀFRUUHFWꢀWKHꢀLQWHUIHUHQFHꢀDWꢀKLVꢀRZQꢀH[SHQVHꢂ  
'RꢀQRWꢀPDNHꢀDQ\ꢀFKDQJHVꢀRUꢀPRGLÀFDWLRQVꢀWRꢀWKHꢀHTXLSPHQWꢀXQOHVVꢀRWKHUZLVHꢀVSHFLÀHGꢀLQꢀWKHꢀLQVWUXFWLRQVꢂꢀ,IꢀVXFKꢀFKDQJHVꢀRUꢀPRGLÀFDWLRQVꢀ  
should be made, you could be required to stop operation of the equipment.  
Canadian Radio Interference Regulations  
This Class A digital apparatus meets all requirements of the Canadian ICES-003.  
WARNING  
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take  
adequate measures.  
9
GB SERVICING  
GB  
AC Power Cord Requirement  
The AC Power Cord supplied with this LCD monitor meets the requirement for use in the country in which you  
purchase it.  
AC Power Cord for the United States and Canada:  
GROUND  
$&ꢀ3RZHUꢀ&RUGꢀXVHGꢀLQꢀWKHꢀ8QLWHGꢀ6WDWHVꢀDQGꢀ&DQDGDꢀLVꢀOLVWHGꢀE\ꢀWKHꢀ8QGHUZULWHUVꢀ/DERUDWRULHVꢀꢃ8/ꢄꢀDQGꢀFHUWLÀHGꢀ  
by the Canadian Standard Association (CSA).  
$&ꢀ3RZHUꢀ&RUGꢀKDVꢀDꢀJURXQGLQJꢇW\SHꢀ$&ꢀOLQHꢀSOXJꢂꢀ7KLVꢀLVꢀDꢀVDIHW\ꢀIHDWXUHꢀWRꢀPDNHꢀVXUHꢀWKDWꢀWKHꢀSOXJꢀZLOOꢀÀWꢀLQWRꢀWKHꢀSRZHUꢀRXWOHWꢂꢀ  
Do not try to defeat this safety feature. Should you be unable to insert the plug into the outlet, contact your electrician.  
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE  
End-User License  
The product (meaning the equipment or appliance to which this documentation relates) incorporates Software (the software applications, utili-  
ties and modules embedded within the Product) which is owned by Sanyo or its licensors. Before using the product, please read the End-User  
License Conditions detailed below. If you do not agree to the terms and conditions of the End-User License, Please do not proceed to use the  
Product- repack the Product unused and return it to your supplier together with proof of purchase for a full refund. By using the product, you  
agree to be bound by the terms and conditions of the End-User License.  
/LFHQVHꢀ*UDQWꢁꢀ&RQGLWLRQVꢀDQGꢀUHVWULFWLRQV  
1.6DQ\RꢀJUDQWVꢀ\RXꢀDꢀQRQꢇH[FOXVLYHꢁꢀZRUOGꢇZLGHꢀꢃVXEMHFWꢀWRꢀH[SRUWꢀFRQWUROVꢄꢁꢀQRQꢇWUDQVIHUDEOHꢀꢃH[FHSWꢀDVꢀSHUPLWWHGꢀE\ꢀꢈꢀEHORZꢄꢁꢀUR\DOW\ꢇIUHHꢀ  
license to use the Software upon and with the Product.  
2. You may not transfer any of your license rights in the Software without the prior written consent of SANYO and if consent is provided then  
the Software shall only be transferred in conjunction with the transfer of the Product AND provided that the transferee has read and agreed  
to accept the terms and conditions of this license.  
3. You must ensure that the copyright, trademark and other protective notices contained in the Software are maintained and not altered or  
removed.  
4. The Software provided hereunder is copyrighted and licensed (not sold). SANYO especially does not transfer title or and ownership rights  
in the Software to you. The Software provided hereunder may contain or be derived from portions of materials provided to SANYO under  
license by a third party supplier.  
5.ꢀ([FHSWꢀDVꢀH[SUHVVO\ꢀSHUPLWWHGꢀE\ꢀVWDWXWHꢀ\RXꢀPD\ꢀQRWꢉ  
L XVHꢀWKHꢀ6RIWZDUHꢀLQꢀFRQMXQFWLRQꢀZLWKꢀDQ\ꢀRWKHUꢀFRPSXWHUꢀKDUGZDUHꢀRWKHUꢀWKDQꢀWKHꢀSURGXFWꢉ  
L FRS\ꢀDOOꢀRUꢀSDUWꢀRIꢀWKHꢀ6RIWZDUHꢉ  
L LQFRUSRUDWHꢀDOOꢀꢃRUꢀDQ\ꢀRIꢄꢀWKHꢀ6RIWZDUHꢀLQWRꢀRWKHUꢀSURJUDPVꢀGHYHORSHGꢀE\ꢀꢃRUꢀRQꢀEHKDOIꢀRIꢄꢀ\RXꢀDQGꢊRUꢀXVHGꢀE\ꢀ\RXꢉ  
L UHYHUVHꢇHQJLQHHUꢁꢀGHFRPSLOHꢀRUꢀGLVDVVHPEOHꢀWKHꢀ6RIWZDUHꢉ  
L PDNHꢀWKHꢀ6RIWZDUHꢀꢃRUꢀDQ\ꢀSDUWꢀRIꢀLWꢄꢀDYDLODEOHꢁꢀRUꢀSHUPLWꢀLWVꢀUHGLVWULEXWLRQꢁꢀIRUꢀXVHꢀZLWKꢀDQ\ꢀFRPSXWHUꢀKDUGZDUHꢀRWKHUꢀWKDQꢀWKHꢀ3URGXFWꢉꢀRUꢀ  
rent, lease, gift, loan, sell, distribute or transfer possession of the whole or any part of the Software.  
Termination  
This license is effective until terminated. This license will terminate automatically without notice if you fail to comply with any of its provisions.  
Disclaimer  
1.7KHꢀ6RIWZDUHꢀLVꢃWRꢀWKHꢀH[WHQWꢀSHUPLWWHGꢀE\ꢀODZꢄꢀVXSSOLHGꢀ´DVꢀLVµꢀDQGꢀ6$1<2ꢀDQGꢀLWVꢀVXSSOLHUVꢀH[SUHVVO\ꢀH[FOXGHꢀDOOꢀZDUUDQWLHVꢁꢀH[SUHVVꢀRUꢀ  
LPSOLHGꢁꢀLQFOXGLQJꢀꢃEXWꢀQRWꢀOLPLWHGꢀWRꢄꢀZDUUDQWLHVꢀRIꢀVDWLVIDFWRU\ꢀTXDOLW\ꢁꢀÀWQHVVꢀIRUꢀSXUSRVHꢀDQGꢀQRQꢇLQIULQJHPHQWꢀꢃVDYHꢀWRꢀWKHꢀH[WHQWꢀWKDWꢀWKHꢀ  
VDPHꢀDUHꢀQRWꢀFDSDEOHꢀRIꢀH[FOXVLRQꢀDWꢀODZꢄꢂ  
2.,QꢀQRꢀFLUFXPVWDQFHVꢀZLOOꢀ6$1<2ꢀEHꢀOLDEOHꢀIRUꢀDQ\ꢀGLUHFWꢁꢀLQGLUHFWꢁꢀFRQVHTXHQWLDOꢁꢀRUꢀLQFLGHQWDOꢀGDPDJHꢀꢃLQFOXGLQJꢀORVVꢀRIꢀSURÀWVꢁꢀEXVLQHVVꢀ  
interruption, loss of data or the cost of procurement of substitute goods, technology or services) arising out of the use or the inability to use  
WKHꢀ6RIWZDUHꢀꢃVDYHꢀWRꢀWKHꢀH[WHQWꢀWKDWꢀVXFKꢀOLDELOLW\ꢀLVꢀQRWꢀFDSDEOHꢀRIꢀH[FOXVLRQꢀDWꢀODZꢄꢂ  
General  
1. This End-User License will be governed by laws of England and the User may only bring claims in the English Courts and SANYO shall be  
entitled to bring a claim in the courts of any jurisdiction.  
2. This End-User License is governed by the laws of the State of California. The End-User and Sanyo agree that any action to enforce or  
interpret the terms of this End-User License shall be brought only in the appropriate state or federal court located in Los Angeles County,  
&DOLIRUQLD7KHꢀ(QGꢇ8VHUꢀDQGꢀ6DQ\RꢀKHUHE\ꢀVXEPLWꢀWRꢀWKHꢀH[FOXVLYHꢀMXULVGLFWLRQꢀDQGꢀYHQXHꢀRIꢀVXFKꢀFRXUWꢂ  
3. The above terms and conditions supersede any prior agreement, oral or written, between you and SANYO relating to the Software.  
10  
GB  
GB  
INSTALLATION  
Step: 1 Mains Connection  
N&RQQHFWꢀWKHꢀGLVSOD\ꢀXQLWꢀWRꢀ9*$ꢁꢀ%1&ꢀDQGꢀ6FDUWꢀFRQ-  
nector as required.  
LD-Net  
ꢎꢀ7KLVꢀÀJXUHꢀLVꢀꢏꢈꢀLQFKꢀPRGHOꢂ  
1. Connect the in-line power connector to the Mains Inlet as shown  
4. AV3  
Composite (CVBS) signal input.  
above.  
AV3-OUT can be used to output the incoming AV3 signal to the  
other monitor.  
2. Connect the power cord of the LCD monitor to a suitable wall  
outlet.  
5. DVI-D (Digital Video Interface)  
As this product does not have a mains On/Off switch, please  
DVI-D supports a large range of resolutions as shown in the IN-  
STRUCTION MANUAL on page 17.  
ensure your mains plug is easily accessible.  
The LCD monitor is prepared for a mains voltage AC100 ~ 240V,  
ꢋꢌ+]ꢊꢍꢌ+]ꢂꢀ7RꢀFRPSOHWHO\ꢀVZLWFKꢀRIIꢀWKHꢀPDLQVꢁꢀRUꢀZKHQꢀWKHꢀ  
GLVSOD\ꢀXQLWꢀLVꢀQRWꢀWRꢀEHꢀXVHGꢀIRUꢀDQꢀH[WHQGHGꢀSHULRGꢀRIꢀWLPHꢁꢀLWꢀLVꢀ  
advisable to disconnect the power cord from the power outlet.  
6. PC connection  
PC input (PC-IN D-SUB). This input supports a large range of reso-  
lutions as shown in the INSTRUCTION MANUAL page 17. Audio  
can be connected via the 3.5mm PC-AUDIO IN.  
A
C
Mains  
O
u
tle  
t
7. External Speaker  
Output the audio signal from AV1, AV2, AV3, PC and DVI.  
The speaker impedance is 8 ohms.  
Please use the correct mains lead supplied with the set for your  
area.  
3. Warning: To prevent injury, the unit must be securely attached to  
the wall in accordance with the installation instructions.  
WARNING! High voltages are used in the  
RSHUDWLRQꢀRIꢀWKLVꢀVHWꢂꢀ5HIHUꢀVHUYLFHꢀWRꢀTXDOLÀHGꢀ  
service personnel.  
8. AV2 / DVI AUDIO IN  
Connect the audio output (stereo) from a computer or video equip-  
ment connected AV2 or DVI.  
Step: 2 Connections  
N INPUT selection  
To switch either AV1, RGB, AV2, AV3, PC, DVI or Network by pressing  
the INPUT button on your remote control repeatedly.  
1. AV1  
SCART connection/CVBS/RGB/S-VIDEO.  
2. RGB  
9. Monitor Audio OUT  
TTL input (5V RGB signals) into SCART terminal.  
7KLVꢀWHUPLQDOVꢀRXWSXWꢀÀ[HGꢀOHYHOꢀIURPꢀ$8',2ꢀ,1ꢂ  
ꢃꢂꢀ<ꢁꢀ3Eꢁꢀ3Uꢄ5*%+9ꢀFRQQHFWLRQꢀꢅ$9ꢆꢇ  
10. RS232C IN/OUT  
Choose Y, Pb, Pr or RGB H/V connection by selecting AV2 Setting  
in Set up menu (refer to the INSTRUCTION MANUAL on page 10).  
You can connect your DVD player to the Y, Pb, Pr terminals instead  
RIꢀXVLQJꢀDꢀVFDUWꢀOHDGꢂꢀ7KLVꢀFDQꢀVXSSRUWꢀKLJKꢀGHÀQLWLRQꢀLQꢀDQDORJXHꢀ  
component form. RGB H/V can be used as a PC input via the BNC  
terminals. Both options support a large range of resolutions (refer  
to the INSTRUCTION MANUAL on page 17). AV2-OUT can be used  
to output the incoming AV2 signal to the other monitor.  
When the monitor is controlled by a computer, connect to this jack  
with serial control cable.  
You can connect to another monitor with RS232C OUT.  
:KHQꢀ\RXꢀFRQQHFWꢀ3&ꢀZLWKꢀ56ꢈꢆꢈ&ꢁꢀVHOHFWꢀ´21µꢀDWꢀ1HWZRUNꢀ  
standby in Installation mode.  
,IꢀLWꢀLVꢀVHOHFWHGꢀ´2))µꢁꢀ56ꢈꢆꢈ&ꢀWHUPLQDOVꢀGRꢀQRWꢀIXQFWLRQDOꢂꢀ$OVRꢀ  
VHOHFWꢀSXVKꢀEXWWRQꢀWRꢀ´6(5,$/ꢀ32$57µꢂ  
11  
GB INSTALLATION  
GB  
Remote control  
Standby  
Input  
To switch the monitor on and off. Also, refer to the  
INSTRUCTION MANUAL on page 8.  
To switch input source from AV1, RGB, AV2, AV3,  
PC, DVI or Network mode.  
Recall  
To display input selection information and the Time  
set.  
Wide  
You can also select colour systems in AV1/AV3  
mode as follows: AUTO í PAL í SECAM í  
NTSC í NTSC4.43 í PAL M í PAL N.  
To select the screen mode Full, Full All, Zoom  
16:9, Title in 16:9, Zoom 14:9, Title in 14:9,  
Normal or Natural wide.  
Refer to the INSTRUCTION MANUAL on page 12.  
Auto PC  
It can also be automatically adjusted in PC mode  
by pressing this button for twice .  
Menu  
7RꢀHQWHUꢀDQGꢀH[LWꢀWKHꢀPDLQꢀPHQXꢁꢀDQGꢀVXEꢀPHQXꢂ  
Back  
Used to return to the previous menu.  
Up and Down  
Level Up/Down  
7RꢀVHOHFWꢀWKHꢀQH[WꢀRUꢀSUHYLRXVꢀLWHPꢂ  
To adjust the sound volume level or enter sub  
mF/eOnuKs.  
Sound Mute  
7RꢀFRQÀUPꢀWKHꢀLQLWLDOꢀVHWWLQJꢀLQꢀWKHꢀPHQXꢂ  
To mute the sound from the speakers.  
The sound changes as follows: Normal  
volume  
Picture mode selector  
Mute.  
Press the  button repeatedly to select the fol-  
lowing picture mode.  
Bass Expander  
Personal - Personal preference mode.  
Standard - Normal viewing mode.  
Dynamic - Suitable for brightly lit rooms.  
Soft - Low contrast setting  
To get an emphasised bass sound ON or OFF.  
TXT/TV  
7RꢀVHOHFWꢀ7HOHWH[WꢀPRGHꢂ  
Eco - Suitable for dimly lit rooms and gives a cin-  
ema-like effect.  
Main/Sub Picture Swap  
To swap Main and Sub picture.  
)UHH]H  
ON/OFF  
To switch picture still on or off.  
To switch OFF í PIP(1) í PIP(2) í POP mode  
in turn.  
Green  
Press this button for more than 5 seconds, installa-  
tion mode will appear.  
Refer to the INSTRUCTION MANUAL on page 13.  
FOR EU USERS  
Remote control battery installation  
The symbol mark and recycling systems described below apply to EU  
countries and do not apply to countries in other areas of the world.  
Your SANYO product is designed and manufactured with high quality  
materials and components which can be recycled and/or reused.  
The symbol mark means that electrical and electronic equipment,  
batteries and accumulators, at their end-of-life, should be disposed of  
separately from your household waste.  
Note:  
If a chemical symbol is printed beneath the symbol mark, this chemi-  
cal symbol means that the battery or accumulator contains a heavy  
metal at a certain concentration. This will be indicated as follows: Hg:  
mercury, Cd: cadmium, Pb: lead  
In the European Union there are separate collection systems for used  
electrical and electronic equipment, batteries and accumulators.  
Please, dispose of them correctly at your local community waste col-  
lection/recycling centre.  
Please, help us to conserve the environment we live in!  
,QVWDOOꢀWZRꢀ´$$µꢀꢅꢂꢋꢀYROWꢀEDWWHULHVꢀVRꢀWKDWꢀWKHꢀ´ꢐµꢀDQGꢀ´²µꢀPDUNVꢀRQꢀWKHꢀ  
EDWWHULHVꢀPDWFKꢀWKHꢀ´ꢐµꢀDQGꢀ´²µꢀPDUNVꢀLQVLGHꢀWKHꢀXQLWꢀLQWRꢀWKHꢀUHPRWHꢀ  
control handset.  
12  
INSTALLATION  
GB  
GB  
Controls and Menus  
Menu Operation  
Many of your monitors functions are controlled through the menu  
function, using the remote control.  
MENU  
Picture  
Brightness  
Contrast  
Color  
Tint (only if NTSC equipment is detected)  
Sharpness  
White Tone  
White Tone / R / G / B  
Advanced Setting  
DCDi / ACC/ACM / CCS / DNR / MPEG NR / Film Mode  
Sound  
Time  
Treble  
Bass  
Balance  
On / Off  
Bass Expander  
Current Weekday  
Current Time  
Schedule  
Weekday  
Time  
1 - 20  
Action  
Power On / Power Off  
On Program  
AV1 / RGB / AV2 / AV3 / PC / DVI / Network  
On / Off  
Active  
Setup Menu Setup  
Language / H/V-Position / Duration / Transparence  
PIP / POP Setup  
PIP/POP Mode / Main/Sub Source / PIP Position  
Initial Settings  
Text Language  
Tile Mode  
Western / Eastern / Russian / Arabic / Farsi  
Tile Mode Active / H/V_Sets / H/V Location / Bezel H/V Adjustment  
q
w
AV2 Setting  
XGA Mode  
RGBHV / YPbPr  
XGA / WXGA 1366x768  
On / Off  
PC Power save  
PC Adj. Auto Adjust  
H-Position  
V-Position  
Clock  
å The LCD display has a Standby light to show there is power.  
Phase  
Switching into/from standby mode  
During menu operation the bottom of the on screen display will show  
which controls can be used for menu navigation.  
The Standby mode is used for switching the LCD monitor off for short  
periods of time. In standby mode the monitor is switched off but is still  
receiving mains power.  
Press the MENU button to enter the main menu. Whenever main  
menu is accessed initially, PICTURE will be the default selection.  
L TTohetubrnluethpeomwoenriitnodriicnatotosrtiallnudmbinyamteosdme,oprreebssrigthhetly. button.  
L Taogatuinr.n the monitor ON from standby mode, press the  button  
A sub menu is selected using the  or  button and pressing  
the  or  button when the required sub menu is highlighted.  
:KHQꢀ\RXꢀKDYHꢀÀQLVKHGꢀ\RXꢀFDQꢀSUHVVꢀWKHꢀBACK button to return to  
the previous menu, press the MENU buttonꢀWRꢀH[LWꢀWKHꢀPHQXꢀRSHUDWLRQꢂ  
,Iꢀ\RXꢀÀQGꢀWKHꢀSRZHUꢀLQGLFDWRUꢀÁDVKLQJꢁꢀGLVFRQQHFWꢀ  
power cord from the power outlet and contact our  
Service desk.  
This warning is a sign to let you know that the  
power protection function of this TV set is now  
operating.  
Picture menu  
1. Press the MENU button. PICTURE will be the default selection.  
Press the  or  button to enter.  
ç Control buttons (bottom corner of back cover)  
6HWꢀWKHꢀSLFWXUHꢀVHWWLQJVꢀIRUꢀ\RXUꢀ´personalµꢀSUHIHUHQFHꢂ  
Menu button: Used to display or cancel main menu.  
Input/  button: Switch between AV1, RGB, AV2, AV3, PC , DVI  
or Network mode. It is also used to provide sub  
menu selection from the Main Menu.  
2. Use the  or  button to select eg. Brightness and the  or  
 button to adjust levels.  
 or  buttons: provide up and down adjustments.  
N White Tone  
 button: To switch to standby mode (to switch off completely  
May be used to adjust the color tone of the picture. Use the  or  
 button to select White Tone and press the  or  button  
to enter the sub menu. You can select Personal, Cool, Standard or  
Warm settings by using the  or  button. To adjust the color  
tone of the picture by using the  or  button to select Red(R),  
Green(G) or Blue(B) and the  or  button to adjust levels.  
These settings will be stored in personal mode automatically.  
disconnect the monitor from the power supply).  
13  

XO Vision XO1915BT User Manual
Westcott 4899 User Manual
Westcott 1865 User Manual
Weil McLain CG Series 10 User Manual
Swann SW244 VR5 User Manual
Sony DXC3000 User Manual
Sony DVD203 User Manual
Sony DCR TRV27 User Manual
Sharp AQUOS BD HP80U User Manual
Rosewill Blender R W320 T User Manual