Rockford Fosgate FNX 1405 User Manual

®
®
c a r a u d i o for  
f a n a t i c s  
component systems  
operation &  
installation  
T
ABLE O F  
C
O N T EN T S  
Introduction................................................................................................ 1  
Package Contents ....................................................................................... 1  
Design Features .......................................................................................... 2  
Installation Considerations ........................................................................... 4  
Mounting Location ...................................................................................... 5  
Installation ................................................................................................. 6  
Troubleshooting ........................................................................................ 10  
Specifications ........................................................................................... 11  
Warranty Information ................................................................................ 12  
International Information ............................................................................ 13  
GETTING  
S
TARTED  
Welcome to Rockford Fosgate! This manual is designed to provide information  
for the owner, salesperson and installer. For those of you who want quick  
information on how to install this product, please turn to the Installation  
Section of this manual or refer to the icons listed below. Other information can  
be located by using the Table of Contents. We, at Rockford Fosgate, have  
worked very hard to make sure all the information in this manual is current. But,  
as we are constantly finding new ways to improve our product, this information  
is subject to change without notice.  
I
N
S
T
A
L
L
A
T
I
®
®
TROUBLE-  
S
H
O
O
T
I
N
G
O
N
Sections marked  
TROUBLESHOOTING  
Sections marked  
INSTALLATION  
include recommendations for  
curing installation problems  
include slam dunk”  
wiring connections  
IN TRO D U C TI O N  
This manual provides information on the features and installation of the  
Fanatic X Systems. We suggest you save this manual for future reference.  
We strongly recommend you have your Authorized Rockford Fosgate Dealer  
install the Fanatic X System. If you do choose to install the system yourself,  
please be sure to read the entire manual before beginning.  
P
ACKAGE  
C
O NTENTS  
FNX1514  
(2) FNX1401 Tweeters  
FNX1414  
(2) FNX1401 Tweeters  
Includes 3/4" [20mm] silk dome tweeter,  
flush mount housing, surface mount housing,  
wedge mount housing  
Includes 3/4" [20mm] silk dome tweeter,  
flush mount housing, surface mount housing,  
wedge mount housing  
(2) Tweeter Mounting Brackets  
(4) #8 32 x .500 Screws  
(2) Tweeter Mounting Brackets  
(4) #8 32 x .500 Screws  
(4) #8 32 Black Nuts  
(4) #8 32 Black Nuts  
(8) #8 x .75 Phillips Screws  
(2) .110 Female Fast-on Connectors  
(2) .110 Male Fast-on Connectors  
(2) FNX1405 514" Midrange Speakers  
(2) 514" Speaker Grilles  
(8) #8 x .75 Phillips Screws  
(2) .110 Female Fast-on Connectors  
(2) .110 Male Fast-on Connectors  
(2) FNX1404 4" Midrange Speakers  
(2) 4" Speaker Grilles  
(2) 514" Speaker Grille Rings  
(2) RF” Speaker Grille Logos  
(2) FNX142x 2-Way Crossovers  
(8) #8 x 1.25 Phillips Screws  
(20) 18 Gauge Speaker Wire  
(2) 4" Speaker Grille Rings  
(2) RF” Speaker Grille Logos  
(2) FNX142x 2-Way Crossovers  
(8) #8 x 1.25 Phillips Screws  
(20) 18 Gauge Speaker Wire  
FNX1614  
FNX1614F  
(2) FNX1401 Tweeters  
(2) FNX1401 Tweeters  
Includes 3/4" [20mm] silk dome tweeter,  
flush mount housing, surface mount housing,  
wedge mount housing  
Includes 3/4" [20mm] silk dome tweeter,  
flush mount housing, surface mount housing,  
wedge mount housing  
(2) Tweeter Mounting Brackets  
(4) #8 32 x .500 Screws  
(2) Tweeter Mounting Brackets  
(4) #8 32 x .500 Screws  
(4) #8 32 Black Nuts  
(4) #8 32 Black Nuts  
(8) #8 x .75 Phillips Screws  
(2) .110 Female Fast-on Connectors  
(2) .110 Male Fast-on Connectors  
(2) FNX1406 612" Midrange Speakers  
(2) 612" Speaker Grilles  
(8) #8 x .75 Phillips Screws  
(2) .110 Female Fast-on Connectors  
(2) .110 Male Fast-on Connectors  
(2) FNX1406F 6" Midrange Speakers  
(2) 6" Speaker Grilles  
(2) 6" Speaker Grille Rings  
(2) RF” Speaker Grille Logos  
(2) FNX142x 2-Way Crossovers  
(8) #8 x 1.25 Phillips Screws  
(20) 18 Gauge Speaker Wire  
(2) 612" Speaker Grille Rings  
(2) RF” Speaker Grille Logos  
(2) FNX142x 2-Way Crossovers  
(8) #8 x 1.25 Phillips Screws  
(20) 18 Gauge Speaker Wire  
– 1 –  
D
ESIGN FEATURES  
4
5
6
2
7
3
1
9
10  
12  
8
11  
Tweeter  
1. 3/4" Silk Dome Tweeter – To ensure accurate high frequency reproduction, the  
tweeter dome must be both light and strong. The Fanatic X Component Systems  
use a silk dome that has extremely low mass and high strength for smooth high  
frequency reproduction.  
2. Ferrofluid Cooling – This synthetic fluid is held in place in the magnetic gap. It  
bathes the voice coil allowing higher power handling and greater reliability.  
3. Neodymium Magnet – What good would a tweeter be if it was too big to mount  
in your favorite spot? The Fanatic Component Systems use a highly efficient  
neodymiummagnettoenablea verysmalltweetertohaveverybigperformance.  
– 2 –  
D
ESIGN FEATURES  
Midrange  
4. Rubber Surround – The durable rubber surround withstands the  
extremes of the automotive environment. It also improves sound quality  
by reducing 2nd and 3rd order harmonics and provides wider frequency  
response.  
5. Mica Filled Polypropylene Cone – The ideal cone material would be  
infinitely strong, very light and would have very high damping to ensure  
great sound quality. The Fanatic X Series Component Systems use a  
mica filled polypropylene cone that is strong, light and has high internal  
damping to provide excellent reproduction of sound.  
6. Cupped Spider – The spider has the job of centering the voice coil and  
providing the rear suspension for the speaker. The Fanatic X Component  
Systems use a durable cupped spider to ensure great sound with long  
life and durability.  
7. Large 1" Voice Coil with Anodized Aluminum Former – Just like all  
Rockford Fosgate woofers, all Fanatic Component System midrange  
drivers use an aluminum voice coil former for more efficient dissipation  
of heat. Dissipating the heat is key to long life and high power handling,  
so go ahead and crank it up!  
8. VentedPole Piece Thepolepieceextendsfromthebackofthespeaker  
into the voice coil area. The Fanatic X Component System uses a vented  
pole piece to allow cool air to circulate in the voice coil gap which allows  
greater power handling and increased reliability.  
Crossover  
9. 2 WayButterworthCrossoverFeaturesan18dBperoctavehigh-pass  
crossoverforthetweeteranda 6dBlow-passcrossoverforthemidrange.  
The steeper slope of the tweeter crossover gives better power handling.  
The low-pass crossover provides a seamless transition between tweeter  
and midrange.  
10. Optical CompressionThis built-in protection circuit limits power to the  
tweeter when the “danger” threshold is exceeded. Because it simply  
limits power and doesn't shut the tweeter off, this circuit is completely  
inaudible.  
11. Gold-Plated Screw Terminals Terminals plated in gold for maximum  
resistance to corrosion to ensure great sound for years to come. These  
terminals accept bare wire or 1/4" spade lug connectors.  
12. 0dB/–3dB Tweeter Pad In some installations, you may find that the  
tweeter location is much closer to your ears than the midrange. This pad  
allows you to match the tweeter level to the midrange for the best  
balance.  
– 3 –  
I
N STALLATIO N  
C
O N SID ERATIO N S  
Tools Needed  
The following is a list of some of the tools necessary for the installation of your  
speakers.  
Power Drill with assorted bits  
Tape Measure  
#2 Phillips Screwdriver  
Voltmeter  
General  
1. For safety, disconnect the negative lead from the battery prior to beginning  
the installation.  
2. Neverrunwiresunderneaththevehicle. Runningthewiresinsidethevehicle  
provides the best protection.  
3. Avoid running wires over or through sharp edges. Use rubber or plastic  
grommets to protect any wires routed through metal.  
4. Mount the speakers/crossovers away from electrical sources (other than the  
amplifier) i.e., power cables, electronic fuel pumps, vehicle computers,  
and other potential noise sources.  
5. Mount the speakers/crossovers away from areas of extreme heat or  
moisture.  
Speakers  
1. Make sure there is an area large enough for the speaker to mount. Warning!  
Failure to do this can cause damage to the speaker if the speaker frame  
is bent during installation.  
2. Check to see that the location is deep enough for the speaker(s) and the  
location does not interfere with the normal operation of the vehicle.  
3. When mounting the speaker(s) in the door of a vehicle, make sure the  
speaker(s) do not interfere with either the door or window operation.  
4. When mounting the speaker(s) on the rear deck of the vehicle, check the  
operation of the rear hatch or trunk lid. Make sure the torsion bars and other  
moving parts are not obstructed by the speaker(s) installation.  
• Please refer to the Specifications section of this manual for proper mounting  
diameter and depth of the speaker(s).  
Crossovers  
1. Make sure there is a flat area large enough for the crossover to mount.  
2. For best results, mount the crossover(s) next to the amplifier for a decorative  
finish to the installation and to provide an easy upgrade (no new wires to  
run) for a bi-amp Rockford Fosgate system in the future.  
– 4 –  
M
O UNTING LO CATIO N  
A solid front stage with a good image is one of the most difficult tasks to achieve  
in a vehicle. No car has the optimum listening environment. This makes proper  
sound staging very difficult to accomplish. Most speakers tend to be placed  
where they will fit easily, as opposed to where they can perform the best. The  
mounting location of your speakers will have a great effect on the sound quality  
of your stereo system. The special care taken to place the speakers will yield  
many hours of listening enjoyment in return. Several important recommenda-  
tions should be followed.  
Place the speakers where they have a direct  
path to the listening area.  
Forthebestintegrationbetweenthemidrange  
and tweeter, the tweeter should be placed  
less than 2" from the midrange. (Figure 1)  
If you cannot place the tweeter less than 2"  
from the midrange, then place the tweeter  
more than 7" from the midrange. Placing  
the tweeter 2"-7" from the midrange can  
cause destructive interference (frequency  
response problems) which will affect the  
2" or less  
Figure 1  
speaker's ability to reproduce the frequency range around the crossover  
frequency of the system.  
Whenever possible, place the tweeter directly above or below the midrange  
as this maximizes the imaging (point source) capability of the speakers.  
(Figure 2)  
Figure 2-A  
Figure 2-B  
– 5 –  
Sound radiated from a “point source” has the most optimum stereo imaging  
because the separation of the acoustical centers between the midrange and  
tweeter for each channel is at the optimum. Figure 2-A describes a  
horizontal speaker alignment. In a closed environment such as an  
automobile, horizontal speaker alignment can cause severe amplitude and  
phase differences which will degrade not only the imaging, but also the  
frequency response. This is due to the path length differences between the  
midrangeandtweeter. Figure2-Bdisplaysa verticalalignmentbetweenthe  
midrange and tweeter. With a vertical alignment, the path length difference  
between the midrange and tweeter are reduced to a minimum. The result  
is a negligible difference in path lengths between the midrange and tweeter  
regardless of the proximity of the listener to the speakers. Mounting the  
speaker with minimum path length difference will ensure the best staging  
and imaging possible from your audio system.  
I
N
S
T
A
L
L
A
T
I
®
INSTALLATION  
O
N
Mounting the Midrange  
1. Cut the proper size hole for the midrange/woofer.  
For the FNX-1404, cut an 90.48mm (3916") diameter hole  
For the FNX-1405, cut a 113.50mm (41532") diameter hole  
For the FNX-1406F, cut a 127mm (5") diameter hole  
For the FNX-1406, cut a 139.06mm (512") diameter hole  
2. Place the mounting ring over the mounting hole and mark the location of  
the screw mounting holes.  
3. Remove the ring. Drill the holes for the screws using a 1/8" drill bit.  
4. Route the wire through the hole.  
5. Place the mounting ring over the hole.  
6. Attach the wires and be sure to observe the proper speaker polarity.  
7. Place the speaker into the hole and screw the speaker into place. Be  
careful not to bend the speaker frame during this step.  
8. Press the speaker grille into the mounting ring.  
– 6 –  
I
®
®
N
S
T
A
L
L
A
T
I
Flush Mount Tweeter  
O
N
Flush  
Housing  
Trim Ring  
Back  
Plate  
Tweeter  
Surface Mount Tweeter  
Back  
Plate  
Surface  
Housing  
Trim Ring  
Tweeter  
Wedge Mount Tweeter  
Wedge  
Housing  
Tweeter  
– 7 –  
Crossover Connections  
-0db Tweeter Level  
-3db Tweeter Level  
-
+
-
+
-
+
INPUT  
MIDRANGE TWEETER  
+
+
(One channel of  
amplifier)  
Be Sure to Maintain Speaker Polarity  
• 0dB Tweeter Level matches the amplitude of the tweeter to the midrange  
• –3dB Tweeter Level reduces the amplitude of the tweeter –3dB lower than  
the midrange. (ex. ideal for tweeters located high in door panels and  
midranges located low in the kick panel)  
– 8 –  
I
®
N
S
T
A
L
L
A
T
I
Bandpassing the Midrange  
O
N
The Fanatic Component Systems are optimized for full range music reproduc-  
tion. In cases where a subwoofer is used, the midrange can be bandpassed in  
order to prevent overlapping frequencies from the midrange into the  
subwoofer.  
1.Determine the frequency range that the subwoofer will play (i.e.: 20Hz-80Hz)  
2.Use the low-pass crossover frequency of the subwoofer system (i.e.: 80Hz) as  
the high-pass crossover frequency for the midrange  
3.Select the appropriate capacitor value (i.e.: 500µF) to properly bandpass the  
midrange  
4.Place the capacitor in series with the +terminal of the speaker  
-
+
-
+
-
+
INPUT  
MIDRANGE TWEETER  
+
0dB  
–3dB  
C1  
Subwoofer  
Midrange  
Tweeter  
80Hz  
6dB/octave HP  
Frequency  
Hertz  
Speaker  
(4 ohms)  
C1  
80Hz  
100Hz  
130Hz  
200Hz  
260Hz  
400Hz  
500µF  
400µF  
300µF  
200µF  
150µF  
100µF  
– 9 –  
TROUBLE-S  
H
O
O
T
I
N
G
T
R O U BL E SH O O T I N G  
Symptom  
Diagnosis  
Remedy  
No sound from  
speakers  
Wires between amplifier,  
crossover or speakers not  
connected properly.  
Check and repair or replace  
wiring as needed.  
Amplifier has no output.  
Checksystemwithknownwork-  
ing amplifier and repair or re-  
place as needed.  
Check for shorts in the wiring  
with a volt/ohm meter and re-  
pair or replace wires as needed  
Speaker wires are shorted  
to each other or to the chas-  
sis of the vehicle.  
Checksystemwithknownwork-  
ing speaker and repair or re-  
place as needed.  
Speakers are blown.  
Distorted sound  
from speakers  
Check wiring and repair or re-  
place as needed.  
Incorrect wiring between  
crossover and speakers  
Tweeters “burn  
up” easily  
Check gain settings on ampli-  
fier and readjust as necessary  
Excessive power from am-  
plifier  
Checksettingsonequalizerand  
readjust as necessary  
Equalizer in system (if  
available) has excessive  
boost in the high frequency  
range  
Check for shorts in the wiring  
with a volt/ohm meter and re-  
pairorreplacewiresasneeded.  
Engine Noise from  
One or More  
Speakers  
Speaker wires shorted to  
chassis of vehicle.  
Re-route speaker wiring away  
from noise sources. (Refer to  
the Installation Consider-  
ations section of this manual.)  
Speaker wires are routed  
near radiated noise source.  
(Power cables, vehicle  
computers, etc.)  
Move crossovers away from  
noise sources. (Refer to the In-  
stallationConsiderations sec-  
tion of this manual.)  
Crossover is mounted near  
radiated noise source.  
(Power cables, vehicle  
computers, etc.)  
– 10 –  
SP E C I FI C AT I O N S  
System Model Number  
Midrange Model Number  
Nominal Diameter  
Nominal Impedance  
Frequency Response  
Fs (Hz)  
FNX1414  
FNX1514  
FNX1614F  
FNX1406F  
6"  
FNX1614  
FNX1404  
4"  
FNX1405  
FNX1406  
612  
"
514  
"
4  
90Hz-8kHz  
4Ω  
60Hz-6kHz  
60Hz  
4Ω  
61Hz-6kHz  
4Ω  
50Hz-5kHz  
50Hz  
90Hz  
61Hz  
Qes  
.858  
.507  
.507  
.545  
Qms  
4.363  
.717  
3.303  
3.330  
3.508  
Qts  
.440  
.439  
.472  
Vas (ft3/liter)  
.08/2.4  
.11/2.9  
84.8dB  
70 Watts  
.26/7.5  
.15/3.7  
87.4dB  
70 Watts  
.31/8.8  
.15/3.7  
87.9dB  
70 Watts  
.72/20.3  
.15/3.7  
88.4dB  
70 Watts  
Xmax (in/mm)  
Sensitivity  
RMS Power Handling  
Mounting Diameter  
90.48mm  
(3916")  
113.50mm  
(41532")  
127mm  
(5")  
139.06mm  
(512")  
Mounting Depth  
54mm (218")  
60mm (238")  
63mm (21532") 65mm (2916")  
Model  
FNX1401  
3/4" (20mm)  
4Ω  
Model  
FNX142x  
Nominal Diameter  
Nominal Impedance  
Frequency Response  
Fs  
Crossover Type  
2-Way  
Crossover Frequency  
Crossover Slope  
4kHz @ 4Ω  
18dB/octave High-Pass  
6dB/octave Low-Pass  
0.707 (Butterworth)  
Optical Compression  
0dB/–3dB  
1.8kHz-20kHz  
1.8kHz  
Sensitivity  
93dB  
Filter Q  
RMS Power Handling  
Mounting Diameter  
Mounting Depth  
70 Watts*  
See drawings  
See drawings  
Tweeter Protection  
Tweeter Pad  
*Power Ratings (PE) is established with recommended filter network  
Wedge  
.675"  
Mount  
.965"  
1.562"  
1.24"  
.25"  
L = 3.25”  
Surface  
Mount  
1.00"  
1.795"  
L = 4.50”  
Flush  
Mount  
.375"  
1.00"  
H = 1.50”  
-
+
-
+
-
+
INPUT  
MIDRANGE TWEETER  
1.74"  
1.94"  
(Specifications are subject to change without notice)  
– 11 –  
LIMITED  
W
AR R AN T Y  
I
N FO R M AT I O N  
Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following  
terms:  
Length of Warranty  
1 year on speakers  
30 days on speaker B-stock (receipt required)  
90 days on electronic B-stock (receipt required)  
3 years on electronics  
2 years on source units  
What is Covered  
This warranty applies only to Rockford Fosgate products sold to consumers by Authorized  
Rockford Fosgate Dealers in the United States of America or its possessions. Product  
purchased by consumers from an Authorized Rockford Fosgate Dealer in another country  
are covered only by that countrys Distributor and not by Rockford Corporation.  
Who is Covered  
This warranty covers only the original purchaser of Rockford product purchased from an  
Authorized Rockford Fosgate Dealer in the United States. In order to receive service, the  
purchaser must provide Rockford with a copy of the receipt stating the customer name,  
dealer name, product purchased and date of purchase.  
Products found to be defective during the warranty period will be repaired or replaced  
(with a product deemed to be equivalent) at Rockford's discretion.  
What is Not Covered  
1. Damage caused by accident, abuse, improper operations, water, theft  
2. Any cost or expense related to the removal or reinstallation of product  
3. Service performed by anyone other than Rockford or an Authorized Rockford Fosgate  
Service Center  
4. Any product which has had the serial number defaced, altered, or removed  
5. Subsequent damage to other components  
6. Any product purchased outside the U.S.  
7. Any product not purchased from an Authorized Rockford Fosgate Dealer  
Limit on Implied Warranties  
Any implied warranties including warranties of fitness for use and merchantability are  
limited in duration to the period of the express warranty set forth above. Some states do not  
allow limitations on the length of an implied warranty, so this limitation may not apply. No  
person is authorized to assume for Rockford Fosgate any other liability in connection with  
the sale of the product.  
How to Obtain Service  
Please call 1-800-669-9899 for Rockford Customer Service. You must obtain an RA#  
(Return Authorization number) to return any product to Rockford Fosgate. You are  
responsible for shipment of product to Rockford.  
Ship to: Electronics  
Rockford Corporation  
Warranty Repair Department  
2055 E. 5th Street  
Ship to: Speakers  
Rockford Acoustic Design  
(Receiving-speakers)  
609 Myrtle N.W.  
Tempe, AZ 85281  
RA#:_________________  
Grand Rapids, MI 49504  
RA#:_________________  
– 12 –  
– 13 –  
LEA DETENIDAMENTE LAS SIGUIENTES INSTRUCCIONES DE INSTALACIÓN DEL  
PRODUCTO.  
INTRODUCCIÓN  
Este manual contiene información sobre la construcción, installación y  
funcionamiento de los sistemas Fanatic X. Le recomendamos que conserve el  
manual para futuras consultas.  
Es preferible que la instalación de sistema Fanatic X sea realizada por un  
distribuidor autorizado Rockford Fosgate. Si prefiere realizar la instalación usted  
mismo, asegurese de leer el manual en su totalidad antes de comenzar.  
M
ONTAJE  
Le mejor interacción entre tweeter y medio  
se consigue si no están separados entre si  
más de 5 cenimetros. (Figura 1)  
no superior a 5cm  
Figura 1  
I
N
S
T
A
L
L
A
T
I
®
®
I
N STALACIÓN  
Montaje del altavoz de medios  
O
N
– 14 –  
I
®
®
N
S
T
A
L
L
A
T
I
1. Corte el agujero para el medio/woofer.  
O
N
• Par el FNX1404, corte un circulo de 90,48mm de diámetro  
• Par el FNX1405, corte un circulo de 113,50mm de diámetro  
• Par el FNX1406F, corte un circulo de 127mm de diámetro  
• Par el FNX1406, corte un circulo de 139,06mm de diámetro  
2. Use los anillos de montaje de plástico como plantilla. Marque la posición de  
los tornills de anclaje.  
3. Quite el anillo y perfore los agujeros con una broca de 1/8".  
4. Pase el cable de altavoz a través del agujero.  
5. Monte el anillo de montaje sobre el agujero.  
6. Conecte los cables observando la polaridad. Mantenga los cables alejados pe  
partes móviles o cortantes.  
7. Asegure el altavoz en la abertura con los tornillos. Tenga la precaución de no  
doblar el marco del altavoz en este proceso.  
8. Presione la rejilla en el anillo de montaje.  
Conexiones del Crossover  
Nivel de 0dB  
del Agudo  
Nivel de –3dB  
del Agudo  
-
+
-
+
-
+
INPUT  
MIDRANGE TWEETER  
+
+
(Un canal del  
amplificador)  
Asegúrese de mantener la polaridad de los parlantes  
Nivel de 0dB del Agudo cuadra con la amplitud del Agudo al Mediorango  
Nivel de 3dB del Agudo reduce la amplitud del Agudo  
–3dB más bajo que el mediorango. (Ej. Ideal para agudos colocados en paneles  
de puerta elevados y mediorangos localizados en paneles bajos (kick panel)).  
– 15 –  
Veuillez lire les instrucitons suivantes pour l'installation de ces produits.  
I
NTRO D UCTIO N  
Ce manuel contient des informations sur les caractéristiques et l'installation des  
systèmes Fanatic X. Nous vous proposons de garder ce manuel pour toute  
référence future.  
Nous vous recommandons vivement de faire installaer votre système punch  
Fanatic X par un dealer agréé Rockford Fosgate. Si vous choisissez d'installer le  
système vous même, assurez-vous de lire ce manuel entièrement avant de  
commencer.  
EMPLACEMENT DE MONTAGE  
• Pour bénéficier d'une harmonie maximum  
entre le médium et l'aigu l'éloignement  
entre ces deux haut-parleurs devrait être de  
moins de 5 cm entre les 2 chassis. (Figure1)  
moins de 5cm  
Figure 1  
I
N
S
T
A
L
L
A
T
I
®
®
INSTALLATION  
O
N
Montage du haut-parleur médium  
– 16 –  
1. Découper un trou adapté au haut-parleur médium/woofer.  
• Pour le FNX1404, le diamètre du trou est de 90,48mm  
• Pour le FNX1405, le diamètre du trou est de 113,50mm  
• Pour le FNX1406F, le diamètre du trou est de 127mm  
• Pour le FNX1406, le diamètre du trou est de 139,06mm  
2. Placer l'anneau de montage sur le trou et repérer l'emplacement des trous des vis.  
3. Retirer l'anneau. Percer les trous des vis en utilisant une mèche de 3mm.  
4. Faire passer les fils dans le trou central.  
5. Placer l'anneau de montage au-dessus du trou central.  
6. Connecter les fils au haut-parleur en respectant les polarités. Eloigner les fils de  
toute partie tranchante ou mobile du véhicule.  
7. Placer le haut-parleur au-dussus du trou central. Visser le haut-parleur dans son  
emplacement. Faire attention à ne pas tordre le chassis du haut-parleur  
durant cette étape de montage.  
8. Mettre la grille dans l'anneau de montage.  
Connexion du filtre  
Niveau de l’aigu 0dB  
Niveau de l’aigu –3dB  
-
+
-
+
-
+
INPUT  
MIDRANGE TWEETER  
+
+
(Un canal de  
l’amplificateur)  
Vérifier les polaritées des haut-parleurs  
• 0dB Pas d'atténuation de l'aigu par rapport  
• –3dB d'atténuation du niveau de l'aigu –3dB d'atténuation par rapport au  
médium. (Ex: Idéal pour le positionnement de l'aigu en haut de portière et le  
mèdium en bas ou kick panel” Volume de charge créer en bas de port ou dans  
l'angle de celle-ci, au niveau des pieds.  
– 17 –  
Die folgende Bedienungsanleitung soll Ihnen beim Einbau eine Hilfestellung  
geben.  
ENLEITUNG  
Diese Bedienungsanleitung enthält Informationen für den Gebrauch und Einbau  
desPunchFanaticXSystems. Wirempfehlen, dieseauchfürFrageninderZukunft  
sorgfältig aufzubewahren.  
Es ist empfehlenswert, sich das Fanatic X System von einem Autorisierten  
Rockford Fosgate Fachhändler einbauen zu lassen. Sollten Sie den Einbau  
jedochselbervornehmenwollen, soempfehlenwirIhnen, dieBedienungsanleitung  
sorgfälitg zu lesen.  
EINBAUORT  
FürdasoptimaleZusammenspielvonMittel-  
undHochtöner, solltederHochtönerniemals  
weiter als 5cm vorn Mitteltöner entfernt  
montiert werden. (Abb. 1)  
Abstand max. 5cm  
(Abb. 1)  
I
N
S
T
A
L
L
A
T
I
®
®
EINBAU  
Montage des Mitteltöners  
O
N
– 18 –  
1. SchneidenSiedierichtigeLochgröβefürdenMitteltöneroderMidbaβaus.  
Für den FNX1404, schneiden Sie ein 90,48mm Ø Loch  
Für den FNX1405, schneiden Sie ein 113,50mm Ø Loch  
Für den FNX1406F, schneiden Sie ein 127mm Ø Loch  
Für den FNX1406, schneiden Sie ein 139,06mm Ø Loch  
2. Setzen Sie den Montagering auf das Loch und markieren Sie die Löcher  
für die Schrauben.  
3. Nehmen Sie den Ring wieder ab und bohren Sie dann, mit einem  
passenden Bohrer, die Schraubenlöcher vor.  
4. Führen Sie das Kabel durch das Loch.  
5. Plazieren sie den Montagering über dem Loch.  
6. Schlieβen Sie die Lautsprecherkabel an. Kontrollieren Sie, ob die Polarität  
stimmt. Stellen Sie sicher, daβ das Lautsprecherkabel an keinen scharfen  
oder sich bewegenden Teilen anliegt.  
7. Plazieren Sie den Lautsprecher im Loch und befestigen Sie diesen. Seien  
Sie dabei sehr vorsichtig, so daβ sich der Lautsprecherkorb nicht verzieht.  
8. Drücken Sie das Lautsprechergitter im Montagering fest.  
Frequenzweichen Anschlüsse  
0dB  
Hochtonabsenkung  
–3dB  
Hochtonabsenkung  
-
+
-
+
-
+
INPUT  
MIDRANGE TWEETER  
+
+
(Ein Kanal des  
Verstärkers)  
Achten Sie auf die Lautsprecherpolarität  
• 0dB Hochtonabsenkung stimmt mit der Lautstärke des Mitteltöners überein  
• –3dB Hochtonabsenkung, reduziert die Lautstärke des Hochtöners gegenüber der  
Lautstärke des Mitteltöners. –3dB leiser, als der Mitteltöner (Ideal für Einbauten, bei  
denen die Hochtöner im Armaturenbrett und die Mitteltöner in Fuβraum eingesetzt  
werden.  
– 19 –  
Leggere le istruzioni seguenti prima dell'installazione del prodotto.  
I
N TRO D U ZIO N E  
Questo manuale fornisce informazioni sulle caratteristiche e sul installazione dei  
sistemi Fanatic X. Vi suggeriamo di conservare questo manuale come riferimento  
futuro.  
Raccomandiamo fortemente che is sistema sia installato dal vostro rivenditore  
Rockford Fosgate. Se scegliete di procedere con l'installazione da soli, leggete  
attentamente tutto il manuale prima di proseguire.  
P
OSIZIONAMENTO  
• Perottenerela migliorintegrazionetra tweeter  
e midrange, vi suggeriamo di posizionare i  
due componenti a meno di 5 cm tra loro.  
(Figura 1)  
meno di 5 cm  
Figura 1  
I
N
S
T
A
L
L
A
T
I
®
®
INSTALLAZIONE  
Installazione del Midrange  
O
N
– 20 –  
1. Practicate un foro del diametro corretto per il midrange/woofer  
• 90,48mm per FNX1404  
• 113,50mm per FNX1405  
• 127mm per FNX1406F  
• 139,06mm per FNX1406  
2. Posizionate l'anello della griglia sul foro e segnate la posizione delle viti.  
3. Togliete l'anello e forate il pannello con una puna da 3,5mm.  
4. Passate i cavi attraverso il foro.  
5. L'anello della griglia sopra il foro dell'altoplarlante.  
6. Collegate i cave assicurandovi di osservare la corretta polarità. Assicuratevi di  
mantenere i cavi lontano da parti in movimento o strutture taglienti.  
7. Posizionate l'altoparlante nel foro ed avvitatelo. Assicuratevi di non piegare  
il cestello dell'altoparlante.  
8. Incastrate la griglia sull'anello di fissaggio.  
Connessioni del crossover  
-0db livello tweeter  
-3db livello tweeter  
-
+
-
+
-
+
INPUT  
MIDRANGE TWEETER  
+
+
(Un canale  
dell’amplificatore)  
Assicuratevi di mantenere la corretta polarita degli altoparlanti  
• 0dB di livello del tweeter accoppia la sensibilita del midrange a quella del tweeter  
• –3dB di livello del tweeter riduce l'efficienza del tweeter 3dB meno del midrange  
(es.: ideale per tweeter posizionati nella parte alta delle portiere e midrange molto  
bassi nelle tasche)  
– 21 –  
NOTES  
– 22 –  
NOTES  
– 23 –  
NOTES  
– 24 –  
MADE IN THE USA  
This product is designed, developed and assembled in the USA by a dedicated  
group of American workers. The majority of the components used in the  
construction of this product are produced by American companies. However,  
due to the global nature of their manufacturing facilities and the loudspeaker  
parts industry in general, some parts may be manufactured in other countries.  
Rockford Fosgate  
Rockford Corporation  
546 South Rockford Drive  
Tempe, Arizona 85281 U.S.A.  
In U.S.A., (602) 967-3565  
In Europe, Fax (49) 8503-934014  
In Japan, Fax (81) 559-79-1265  
1/98  
LIT9944  

Radio Shack 23 149A User Manual
QSC Audio Car Speaker AD C821 User Manual
Philips SCB4375NB User Manual
Panasonic DMCSZ8K User Manual
Panasonic Camcorder HC V10M User Manual
Olympus CAMERA HOUSING FL 50 User Manual
Miller Camera Support 1584 User Manual
Magnat Audio Xcess 216 User Manual
LG Electronics LG Lifes Good Blu ray Player HR932M User Manual
Kenwood KDV S250P User Manual