13.3" High Res TFT-LCD Monitor
PLVW1340M
Usage Notice
Follow all warnings, precautions and maintenance as
recommended in this user's manual to maximize the life of your
LCD monitor
To avoid the damage of the LCD monitor and risk of electronic
shock, do not permeate the LCD monitor with water or any
drink.
When this happens, turn off the power, unplug the power cord
and send the LCD monitor to your local dealer or our service
cen-ter as soon as possible.
Use a regular power specification of DC 12V . Do not use any
other power supply different from the regularity.
Do not place objects on or suspend them with the power cord.
This will make the power cord damaged.
Do not assemble or twist the power cord arbitrarily. And do not
put it together with heated object.
Do not try to repair the power cord when it is damaged or
broken, change a new one immediately.
Avoid any metal objects or inflammable dropping into the LCD
monitor from ventilation slots.
Do not attempt to open or disassemble the LCD monitor
yourself as this may cause electronic shock.
When there is smile or peculiar smell in use, unplug the power
cord immediately and send it to your local dealer or our service
center.
When there is damage or breach on the LCD monitor casing,
send it to your local dealer or our service center.
Do not use this LCD monitor in the areas susceptible to
excessive dust, dirt, and humid.
Do not setup the LCD monitor in direct sunlight, extremely hot,
and cold environment.
Do not expose the LCD monitor to rain or moisture.
2
Package
This LCD monitor comes with all the items below. Check to make sure your unit
complete. Contact your dealer immediately if anything is missing.
PLVW1340M & PLVW1350IR
* 13.3" High RES TFT-LCD Monitor
* Overhead Console Mounting Bracket
* Credit Card Size Remote Control with Batteries
* Interface Cable with RCA jacks forAudio / Video
Connection and 12V DC
* User's Manual
PLVW1350IR
* Headphones
* AAA1.5V Batteries
Remote Control
MUTE
POWER
2
1
3
7
4
8
5 6
0
9
FUNCTION/ODS MANU
UP
DOWN
3
User Controls
User Control Overview
* Panel Control
Start Your Installation
Wiring
* Monitor connection
System Cable
Pig Tail
Light cable for the main unit
Car Power/ACC
1. Red
2. Yellow
3. Red +12V
4. Black
Video in
Color
Connection
Audio (Right side)
1. Red RCA
2. Yellow RCA
3. Red Line
4. Black Line
Video in
+12V
Ground
4
Setting Up The Dome Lamps
There are three settings for the interior
light: OFF, DOOR and ON (see diagram
below).
OFF: The lights are switched off.
DOOR: With this setting, the lights only
come on when the vehicle's doors are
opened.
ON: The lights are switched on.
Right
Left
DOOR
ON
OFF
The right sw control right lamp
The left sw control left lamp
Notes:
* There is no electrical cable connected
to position "B", since "B" is connected
to the ground via two screws.
* The power supply must be 12 volts.
OFF
LAMP
Door
ON
SW1
OFF
Battery
R
W
LAMP
Sw2
Door
ON
B
W=White=Connection to the sensor
B=Black=Ground
R=Red=Electrical connection
5
Installation your Monitor
Take care to select a suitable fitting location and securing method for
the monitor:
*The unit should not distract or obstruct the driver.
*The installation should not inhibit the entry to, or the exit from the
vehicle.
*The unit should not interfere with other vehicle components e,g
(sliding sunroof).
*Make sure the unit is installed to a secure, robust mounting location
and cannot become dislodged in the event of an emergency stop.
*Do not support the unit using only the vehicle interior roof lining.
*If driving is required, take care not to penetrate through the other
sheet metal of the vehicle.
*Avoid prolonged use of the monitor when the engine is not running
to prevent draining the vehicle battery.
*Place the mounting metal plate with the nuts facing upward, then,
mount the monitor by screws included
6
Closing Monitor
1. Return the monitor to the central viewing position.
(Refer to the following figure)
2. Push the monitor/TV back into the monitor base unit until
the screen engages with the release button.
Operating the Monitor
* Powering up the monitor
The monitor will be automatically turned on when releasing the
monitor from the base unit and "OFF" when it is closed.
Operating Instructions
Opening the Monitor
1. Press the monitor release button to lower the LCD screen.
2. Lower the monitor until is fixed 90 from the monitor base
unit for viewing (Refer to the following figure.)
7
Press the "+" key to enter the
sub-menu. Press "MENU" button
to go back to the main menu.
* OSD Menus in A/V Source
MAIN MENU
A. Source Selection Menu
CUBS.1 = NTSC
H. SYNC = +15.7K Hz
V. SYNC = -60.0Hz
SOURCE
BRIGHTNESS
CONTRAST
COLOR
AUTO DETECT
S-VIDEO
HUE
VIDEO 1
1
SOURCE
AUDIO
VIDEO 2
2
RECALL
RETURN
EXIT
B. Audio Input Selection Menu
AUDIO
MUTE
VOLUME
RECALL
RETURN
* Quick Adjustment OSD Menus
1. By pressing the "SELECT" button, you may open the following OSD
menus directly. Use "+" or "-" key to make adjustment.
BRIGHTNESS
CONTRAST
COLOR
2. Press "+" or "-" button directly to adjust speaker volume.
VOLUME
8
Function Descriptions
Panel Control
* Power:
* Menu:
Power on/off Control
Pop up the OSD menus. Press the "Menu" button
again to exit the OSD menus. When in sub-menu,
press "MENU" again to go back to the main menu.
* UP/Down Keys: 1. Press the "up/down" key to increase or decrease
volume.
2. Make item selection in OSD menus to increase or
decrease parameters as well.
Remote Control
* Mute:
Press the "Mute" button from the remote control
to still the sound of the LCD monitor.
* Volume:
1. When the OSD menu function is turned off, press
the " up/down " buttons directly from the remote
control to adjust volume.
2. Make item selection in OSD menus to increase
or decrease parametersas well.
* Brightness:
* Contrast:
*Color:
Adjust brightness. (You may choose this from OSD
menu.)
Adjust contrast. (You may choose this from OSD
menu.)
Adjust picture color: (You may choose this from
OSD menu.)
* Power:
When the power switch on the side unit is pushed
to "1" position, you may also turn on or off the
monitor by this "Power" button.
9
Specifications
Screen Size
Resolution
Number of colors
Pixel pitch & Format
13.3" diagonal
1024 (H) x 768 (V) pixels
262, 144 colors
0.264 (H) x 0.264 (V) mm
Vertical Stripe Arrangement
130 cd/m2
Brightness
Maximum Contrast Ratio
Operating Temperature
Storage Temperature
Back light
View Angle L/R
View Angle U/D
200
0 C ~ 50 C
-25 C ~ +60 C
Cold cathode Filament Tube
40/40 Degrees
10/30 Degrees
Monitor Dimension
Monitor Weight
330(W) x 279(H) X 44(D) mm
2.5KG
Graphic Mode
VESA standard mode ( 75Hz)
Supported
450mA
2.25A @ DC 12V
CVBS, RCAx 1
On Screen Display
Power Saving mode
Power Consumption
A/V Video input
Video Input level
1.0V p-p 0.5Vp-p
75 Ohms
1.0Vp-p 0.2Vp-p
600 Ohms
1W x 2
Video Input Impedance
Audio Input Level
Audio Input Impedance
Speaker Rating
10
Appendix
Changing the New Battery in Remote Control
1. Push the cassette button to wards the right. (As shown # 1 in below
figure)
2. Pull the all battery cassette away from the remote control. As shown
# 2 in below figure) Change a new battery.
2
Battery
Cassette Button
1
11
|