POSIFLEX Business Machines Cash Register CR 2200 User Manual

CR-2200 SERIES  
CASH DRAWER  
USER’S MANUAL  
FCC Notes:  
Rev. A0  
This equipment generates, uses, and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions manual, may cause interference  
to radio communications. It has been tested and found to comply with limits for a Class  
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to  
provide reasonable protection against interference when operated in a commercial  
environment. Operation of this equipment in a residential area is likely to cause  
interference in which case the user at his own expense will be required to take whatever  
measures to correct the interference.  
Warranty Limits:  
Warranty terminates automatically when any person other than the authorized  
technicians opens the machine. The user should consult his/her dealer for the problem  
happened. Warranty voids if the user does not follow the instructions in application of  
this merchandise. The manufacturer is by no means responsible for any damage or  
hazard caused by improper application.  
About This Manual:  
Posiflex has made every effort for the accuracy of the content in this manual. However,  
Posiflex will assume no liability for any technical inaccuracies or editorial or other  
errors or omissions contained herein, nor for direct, indirect, incidental, consequential  
or otherwise damages, including without limitation loss of data or profits, resulting  
from the furnishing, performance, or use of this material.  
This information is provided “as is” and Posiflex Technologies, Inc. expressly  
disclaims any warranties, expressed, implied or statutory, including without limitation  
implied warranties of merchantability or fitness for particular purpose, good title and  
against infringement.  
The information in this manual contains only essential hardware concerns for general  
user and is subject to change without notice. Posiflex reserves the right to alter product  
designs, layouts or drivers without notification. The system integrator shall provide  
applicative notices and arrangement for special options utilizing this product. The user  
may find the most up to date information of the hardware from web sites:  
All data should be backed-up prior to the installation of any drive unit or storage  
peripheral. Posiflex will not be responsible for any loss of data resulting from the use,  
disuse or misuse of this or any other Posiflex product.  
All rights are strictly reserved. No part of this documentation may be reproduced,  
stored in a retrieval system, or transmitted in any form or by any means, electronic,  
mechanical, photocopying, or otherwise, without prior express written consent from  
Posiflex Technologies, Inc. the publisher of this documentation.  
© Copyright Posiflex Technologies, Inc. 2007  
All brand and product names and trademarks are the property of their respective holders.  
Part 1  
P/N: 19230900030  
CARTON CONTENTS  
1. Cash drawer pre-assembled.  
2. User’s manual.  
3. Separators of coin compartment: 5 pcs.  
4. Key 2pcs: There is a key serial No. sticker on the cash drawer bottom  
side. If user lost the key he/she can order the key according to this  
number.  
5. Signal Cable depend on model  
a). For CR-2200: The standard signal cable is 21863018010 which has a 8  
pin modular plug at one end to connect to the cash drawer and a 6 pin  
modular plug at the other end to connect to the POS system/printer.  
This cable serves for most popularly used POS equipment such as  
Posiflex POS terminals, all Posiflex POS printers, most Epson POS  
printers, most Star POS printers and all other compatibles. The user  
may cut the 6 pin end or order the ready cut cable CCBLA-180A and  
assemble this free end according to his POS printer specification if the  
POS printer used applies different connection. The cable connection on.  
CCBLA-180A is as below:  
RJ45 Function  
Wire color  
Red  
Blue  
Green  
Yellow  
Pin 1 Drawer open sense  
Pin 2 Drawer open sense return  
Pin 7 + 24V to solenoid  
Pin 8 Drawer kick pulse  
b). For CR-2204: Serial signal RS232 DF9F RJ9 conversion cable  
(21863259900/21863159900).  
c). For CR-2205: USB cable (21863250800/21863150800)  
6. Power Source depend on model  
a). For CR-2200: not applicable  
b). For CR-2204: Power adapter 12VAC 1.5A  
c). For CR-2205: Power adapter 12VAC 1.5A  
Part 3  
INSTALLATION  
Coin compartment adjust:  
Open the top cover and remove any protective materials such as a  
piece of PE foam if it exists.  
The coin compartment separator can be removed from and inserted  
till click into the grooves in adjustable coin compartment zones for appropriate  
compartment size.  
Coin Compartment Separator  
Adjustable Coin Compartment  
CR-2200:  
1). Connect the 8 pin plug of CR cable to cash drawer and the 6 pin plug to  
CR port of POS system or POS printer as shown below:  
Rear View  
8P modular Jack  
Output to drawer  
CR Cable: 21863018010  
Cash Drawer  
With Printer Interface  
Connect to POS System or  
Printer 6P modular Jack  
2). Turn the keylock to standby position.  
CR-2204:  
1). Connect the 4 pin RJ9 plug of RS232 conversion cable to the RJ9 jack  
at the rear side of CR-2204 and connect the DB 9 pin connector to  
RS232 port of host (PC or POS) system as shown in drawing below.  
2). Check the specification of power adaptor on its nameplate. Insert the  
Part 4  
power adaptor into the correct power outlet. Insert the output plug to  
the power jack at rear side of CR-2204 to supply power for drawer  
kickout.  
3). Turn the keylock to standby position.  
4). Set the communication protocol of the RS232 port in host system to  
use baud rate of either 9600 bps or 19200 bps.  
Rear View  
RJ9 (4P4C) modular Jack  
USB Type B Connector  
AC 12V I/P  
Connect to Adaptor  
USB Cable:  
RS232 Conversion Cable:  
(21863150800/21863250800)  
(21863159900/21863259900)  
Connect to RS232 port of host system  
(For CR-2204 only)  
Connect to USB Port of host  
system (For CR-2205 only)  
CASH DRAWER With RS232 & USB Interface  
CR-2205:  
1). The drawer number (PID) is default to be 7. Refer to the guidance for  
“Jumper Setting Change” below if the PID has to be changed.  
2). Connect USB type B connector (more or less square one) of USB  
cable to the USB connector at rear side of CR-2205 and the type A  
connector end to USB port of host (PC or POS) system as shown in  
drawing above.  
3). Check the specification of power adaptor on its nameplate. Insert the  
power adaptor into the correct power outlet. Insert the output plug to  
the power jack at rear side of CR-2205 to supply power for drawer  
kickout.  
4). Turn the keylock to standby position.  
5). Install the USB utility driver from Posiflex Product Information CD  
with Posiflex POS system or visit our web sites  
or  
or  
Switch Setting Change for CR-2204/2205:  
1). Use key to open the cash drawer. Take out the removable tray and you  
Part 5  
can find a control board in the bottom. The lay out of the control  
board is illustrated below.  
4
3
2
1
JP1  
O
N
2). By switch setting at different positions of JP1, interface selection  
between RS232 and USB and PID selection can be made.  
a. Interface select: switch position 1 of JP1 defines interface of the cash  
drawer besides the interface cable used. When switch position 1 is  
ON, the controller responds to RS232 signals. When switch position 1  
is OFF, the cash drawer works to USB interface.  
b. USB PID select: Switch positions 2, 3 or 4 define a drawer number  
for the cash drawer as in below table so that this cash drawer is going  
to respond accordingly in USB communication. Please note that  
within each system there should never be any 2 USB interface cash  
drawers carrying the same drawer number.  
USB PID  
1
2
3
4
5
6
7
0
JP1 SW  
2
3
4
ON  
ON  
ON OFF OFF OFF OFF ON  
ON OFF OFF ON  
OFF ON OFF ON OFF ON OFF ON  
ON OFF OFF ON  
Default setting: Drawer 7 (SW2: OFF; SW3: OFF; SW4: OFF)  
UPOS and WEPOS driver application:  
Please first find in Posiflex Product Information CDROM or  
download from Posiflex web sites for UPOS driver setup. In this application  
CR-2204 responds to OpenDrawer command only; CR-2200/2204 are  
compliant to UPOS version 1.7 and CR-2205 is compliant to UPOS version  
1.8 and is also WEPOS certified.  
Part 6  
FUNCTIONAL TEST  
CR-2200  
1. Follow the printer’s manual of the printer the cash drawer is connected to  
open cash drawer.  
2. If the cash drawer is connected to a Posiflex POS system, follow the  
technical instruction of the system to open the cash drawer.  
CR-2204  
1. Under DOS prompt, type “MODE COM1 9600 N 8 1”. Hit the ENTER  
key.  
2. Type “TYPE CON>COM1”. Hit the ENTER key.  
3. Type “CTRL-G” (Press Ctrl and G keys together). Hit the ENTER key,  
then the drawer will open and pass the test.  
4. Hit CTRL-C (Press Ctrl and C keys together) to return the computer back  
to the normal display mode.  
In case the cash drawer is connected to serial port other than COM1 please  
substitute COM1 above to proper port name.  
CR-2205  
1. Please find in Posiflex Product Information CDROM or go to Posiflex  
the Posiflex Product Information CDROM that comes with any Posiflex  
POS system, please go to folder “\Drivers\CR\USB” and click  
“SETUP.EXE” to install the USB Cash Drawer Test Program.  
2. Start up the test program and click “STATUS” button. The drawer status  
of Open/Close or Not present will be displayed under each drawer  
number as “O”, “C” or “N”  
3. Use a key to turn the lock to standby position (the one marked with sign  
at middle), click the check only the box(es) under the drawer number(s)  
for the drawer(s) to be tested then click the “KICK” button.  
4. The cash drawer will then open and the Open/Close/Not present status of  
the tested drawer number will be renewed accordingly. If these status are  
correct, the USB interface cash drawer passes the test  
Part 7  
SPECIFICATIONS  
MECHANICAL: Dimensions:  
460 (W) x 174.9 (D) x 101.5 (H) mm  
18.2” (W) x 6.9” (D) x 4.0” (H)  
Weight: 4.2 Kg  
Removable tray with a lock-on cover (option)  
ELECTRICAL:  
Power Source  
Solenoid Drive (for CR-2200)  
Pulse Amplitude  
Pulse Width  
12 to 24 VDC  
100 to 250 msec  
10% max.  
Pulse Duty Cycle  
Max. Current Consumption 0.75A @ 12 VDC / 1A @ 24 VDC  
AC Adaptor (for CR-2204/2205)  
Input Voltage  
120 VAC ± 10 % / 240 VAC ± 10 %  
@50 -60 Hz  
Output Voltage  
12 VAC at 1.5 A  
Interface  
Direct Drive: CR-2200  
Serial (RS232C)  
CR-2204  
9600; 19200  
none  
Baud rate  
Parity  
Data Bits  
Stop Bits  
8
1
USB (1.1): CR-2205  
Security Code  
CR-2205  
USB PID  
Drawer Open Sense  
CR-2200  
CR-2204  
CR-2205  
Drawer open sense circuit shorts when drawer open  
Pin 9 in DB9 connector goes high when drawer open  
Through USB driver  
Part 8  
KEYLOCK OPERATION  
Lock ( ): Physically lock the drawer.  
Open ( ): Open the drawer by the key. At this position  
the key can’t be extracted and will be automatically  
springed away once released.  
Standby ( ): Automatically open the drawer by POS printer  
or POS system or interface signal control  
Keylock  
STRUCTURE  
Check Slot  
Inside CR- 2200/ 2204/ 2205  
Adjustable Bill  
compartment  
Adjustable coin  
compartment  
Cash Tray  
Fixed coin compartment  
Check Storage  
Part 9  
T31454  
警告使用者  
這是甲類的資訊產品,在居住的環  
境中使用時,可能會造成射頻干  
擾,在這種情況下,使用者會被要  
求採取某些適當的對策。  
Part 10  

Prince Castle Slicers User Manual
Planar Systems Car Video System PLL2710W User Manual
Pioneer TAD M600 User Manual
Philips HR1841 User Manual
Mars CASHFLOW 129 User Manual
Lochinvar COPPER FIN CB 1256 User Manual
Kramer Electronics Car Amplifier 910 User Manual
Kenwood eXcelon KDC X889 User Manual
Kenwood Excelon DNX8120 User Manual
JVC MARINE CASE GR DVX8 User Manual