InstallatIon Manual
VIP 1003
WaRnInG
TO REDUCETHE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSETHIS
APPLIANCETO RAIN OR MOISTURE.
Caring for the Environment by Recycling
When you see this symbol on a Motorola product, do not dispose of the product with
residential or commercial waste.
Recycling your Motorola Equipment
IMPORTANT SAFETY INSTRUCTIONS
Please do not dispose of this product with your residential or commercial waste. Some
countries or regions, such as the European Union, have set up systems to collect and
recycle electrical and electronic waste items. Contact your local authorities for informa-
tion about practices established for your region. If collection systems are not available,
call Motorola Customer Service for assistance.
•
•
•
•
•
•
•
•
Read these instructions.
Keep these instructions.
Heed all warnings.
Use only attachments and accessories specified by
the manufacturer.
Unplug this apparatus during lightning storms or
when unused for long periods of time.
Follow all instructions.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as when the power-
supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
Do not use this apparatus near water.
Clean only with dry cloth.
•
•
Please recycle this document.
Install in accordance with the manufacturer’s
instructions.
•
•
•
Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
POWER SUPPLY
Battery pack or batteries installed shall not be
exposed to excessive heat such as sunshine, fire
or the like.
•
•
•
Keep distances around the power supply for
sufficient ventilation.
Declaration of Conformity
No naked flame sources, such as lighted candles,
should be placed near the apparatus.
Do not defeat the safety purpose of the polarized or
grounding-type plug. If the provided plug does not
fit into your outlet, consult an electrician for replace-
ment of the obsolete outlet.
We
Motorola, Inc.
Teknikringen 20
SE 583 30 Linköping, Sweden
Do not expose the power supply to dripping or
splashing and do not place objects filled with
liquids, such as vases, on the power supply.
•
Protect the power cord from being walked on
or pinched, particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
declare under our sole responsibility that the product to which this declaration relates are in conformity with
the following directives:
•
Ensure that the mains plug remains readily
operable.
EMC Directive 2004/108/EC
Low Voltage Directive 2006/95/EC
WEEE Directive 2002/96/EC
RoHS Directive 2002/95/EC
according to the following standards:
EN55022, EN55024, EN60950.
CAUTION
TO PREVENT ELECTRICAL SHOCK, DO NOT USETHIS PLUG WITH AN EXTENSION CORD, RECEPTACLE,
OR OTHER OUTLET UNLESSTHE BLADES CAN BE FULLY INSERTEDTO PREVENT BLADE EXPOSURE.
The lightning flash with arrowhead within an equilateral triangle is intended to alert the user to
the presence of uninsulated dangerous voltage within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
© 2009 Motorola, Inc. All rights reserved. No part of this publication may be reproduced in any form or by
any means or used to make any derivative work (such as translation, transformation, or adaptation) without
written permission from Motorola, Inc.
MOTOROLA and the Stylized M logo are registered in the US Patent andTrademark Office. All other prod-
uct or service names are the property of their respective owners.
The exclamation point within an equilateral triangle is intended to alert the user to the pres-
ence of important operating and maintenance (servicing) instructions in the literature accompa-
nying the product.
Motorola reserves the right to revise this publication and to make changes in content from time to time
without obligation on the part of Motorola to provide notification of such revision or change. Motorola
provides this guide without warranty of any kind, implied or expressed, including, but not limited to, the im-
plied warranties of merchantability and fitness for a particular purpose. Motorola may make improvements
or changes in the product(s) described in this manual at any time.
Repairs
If you find the unit in need of repair, contact your system operator for repair or replacement.
2
3
Your ViP 1003 Package
Placement
Enclosed material
Do not cover
The following material should be present in your package.
Do not place anything on top of the set-top box, instead leave a free space
of 20 cm above it for proper ventilation and cooling.
remote control
ethernet
scart
IP set-top box
with 2 aaa batteries
cable
cable
When using the remote control, point it to the IR-receiver in the center of
the front panel. Make sure that there is no obstacle between the remote
control and the set-top box, such as for example a table.
AC adaptor
Installation guide
For best reception of the IR-signals from the remote control to the set-top
box, make sure to place the set-top box close to the edge of the shelf.
PreParingthe remote
control for use
In order to prepare your remote control for use,
insert the batteries.
Carefully place the terminals (+ and -) of the
batteries as indicated on the back of the battery
compartment.
4
5
ViP1003 oVerView
installing
Front panel of models without display
Connecting to broadband
Connect one end of the Ethernet cable to the connector marked
ETHERNET on the rear panel of the set-top box and the other end to a hub
or the Ethernet wall connector provided by your broadband operator.
Connecting to theTV set
Connect one end of the enclosed SCART cable to the SCART connector
markedTV on the set-top box and the other end to yourTV set.
Both analog audio and standard definition video are sent to theTV set
through this connection.
Indicator lED:s
IR receiver
Receives signals from remote control
and keyboard.
• Green light - the set-top box is operational.
• Flashing green light - the set-top box receives
a signal from the remote control or a keyboard.
• Red light - the set-top box is in stand-by mode.
the marking plate is located
on exterior of the bottom of
the apparatus.
tV
Rear panel
Broadband
wall outlet
or hub
EtHERnEt
for broadband
connection
usB
sCaRt (tV)
for connection toTV set
(analog Standard Definition video)
for connection
to external devices.
sPDIF
HDMI
PoWER
for connection to digital
audio equipment
for connection to TV set
(digital High Definition video)
for connection of
external power supply
6
7
installing
installing
Optional:
Connecting High definition Video
Optional:
Connecting to external audio
If yourTV set is HDTV compatible, you can connect the set-top box to
theTV set using the HDMI connector instead of the SCART connector to
receive and display HDTV, i.e. skip installation step and replace it with
If you want to use an external source to play audio such as a stereo or
home cinema equipment.
installation step
.
Using the HDMI connector
Digital audio: Using the SPDIF connector
If yourTV set has a HDMI connector, you can connect it to the HDMI
connector on the set-top box with a HDMI cable (not included) to
receive digital high definition video and digital audio.
Connect an RCA cable (not included) to the SPDIF connector on the
set-top box and connect the other end to your stereo orTV set.
tV
stereo/
HiFi system
8
9
installing
naVigating usingthe remote
control
The navigation buttons (the inner ring comprised
by four arrow buttons and an OK button) are
used to move around on Service portal pages
and in menus, and to select the highlighted
alternative.
Connecting to power
Connecting to power
When all other cables are connected, connect the power cord to
the power connector on the set-top box and to mains power.
The navigation buttons are also used to navigate
web pages, as the buttons of the inner ring will
move the indicator between the different links.
Use the oK button to select links to be opened.
The scroll buttons, the outer ring, are used when a web page contains
more information than can be displayed on aTV screen.
For information about the functionality of the other buttons on the remote
control, please see the information provided by your IPTV provider.
notE:
Do not use an AC adaptor other than
the one that is supplied with the
product. Doing so may cause fire or
seriously damage the set-top box.
notE:
The remote control distributed by your service provider may differ
from the standard Motorola remote control.
OPEN SOURCE SOFTWARE INFORMATION
For instructions on how to obtain a copy of any
source code being made publicly available by
Motorola related to software used in this Motorola
set-top box you may send your request in writing
to:
The Motorola website opensource.motorola.com
also contains information regarding Motorola’s use
of open source.
DisPlaYing Picture
Motorola has created the opensource.motorola.com
to serve as a portal for interaction with the software
community-at-large.
To display the signal from the set-top box
on theTV set, switch to an external input.
(On someTV sets this is done automati-
cally.)There is often a button on theTV re-
mote control for this purpose. Otherwise,
see yourTV User’s Guide for instructions.
an example of
what the input
symbol may look
like.
Motorola, Inc.
OSS Management
2450 Walsh Avenue
Santa Clara, CA 95051
USA
To view additional information regarding licenses,
acknowledgments and required copyright notices
for open source packages used in this Motorola
set-top box, please navigate to the Open Source
Notices section in the user interface.
10
11
|