Kenwood DDX7035 User Manual

MONITOR WITH DVD RECEIVER  
DDX7035  
DDX7045  
DDX7065  
INSTRUCTION MANUAL  
© PRINTED IN JAPAN B64-2843-00/00 (M)(AI)  
Sound Effects Menu  
Sound Effects Menu..........................................68  
• Displaying the Control screen  
• Displaying the Sound Effects Menu screen  
Audio Control ..................................................69  
• Displaying the Audio Control 1 screen  
• Displaying the Audio Control 2 screen  
Equalizer ..........................................................70  
• Displaying the Equalizer screen  
• Tone curve setup  
• Parametric Equalizer  
Zone Control ....................................................74  
• Displaying the Zone Control screen  
Digital Effect ......................................................75  
• Displaying the Digital Effect screen  
Position ..............................................................76  
• Displaying the Position screen  
Hands-Free Unit Control......................................78  
GSM control ....................................................78  
• Displaying the Control screen  
• When called  
• When dialing  
• Calling by Phone Book  
• Addition to Phone Book  
• Editing the Phone Book  
• Quick Dialing  
• Hand Free Setup  
• Reading the SMS (Short Message Service)  
messages  
• Creating an SMS (Short Message Service)  
message  
Glossary ................................................................86  
Troubleshooting Guide........................................87  
Specifications ......................................................92  
English 3  
Before Use  
Audio units you can control from the  
DDX7035/7045/7065 Receiver (in November of  
2003):  
KDC-CPS89, KDC-CPS87, KDC-CPS85, KDC-C719,  
KDC-C717, KDC-C715, KDC-C669, KDC-C667, KDC-C665,  
KDC-D301, KDV-C810, KDC-CPS89P, KCA-HF521,  
KTC-V500N/P/E (Set the "O-N" switch to "N" position if  
provided.)  
2WARNING  
To prevent injury and/or fire, take the following  
precautions:  
• Ensure that the unit is securely installed. Otherwise it  
may fly out of place during collisions and other jolts.  
• When extending the ignition, battery or ground wires,  
make sure to use automotive-grade wires or other wires  
2
with an area of 0.75mm (AWG18) or more to prevent  
cable deterioration and damage to the cable coating.  
Navigation units you can control from the  
DDX7035/7045/7065 Receiver (in November of  
2003):  
KNA-DV2600  
• To prevent short circuits, never put or leave any metallic  
objects (e.g., coins or metal tools) inside the unit.  
• If the unit starts to emit smoke or strange smells, turn  
off the power immediately and consult your Kenwood  
dealer.  
• Do not touch the liquid crystal fluid if the LCD is  
damaged or broken due to shock. The liquid crystal fluid  
may be dangerous to your health or even fatal.  
If the liquid crystal fluid from the LCD contacts your body  
or clothing, wash it off with soap immediately.  
Loading and Replacing the battery  
Use one lithium battery  
(CR2025).  
Insert the batteries with  
Keep on slide  
the + and - poles aligned  
properly, following the  
illustration inside the case.  
Pull out  
2CAUTION  
To prevent damage to the machine, take the  
following precautions:  
2WARNING  
• Make sure to ground the unit to a negative 12V DC  
power supply.  
• Do not open the top or bottom covers of the unit.  
• Do not install the unit in a spot exposed to direct sunlight  
or excessive heat or humidity. Also avoid places with too  
much dust or the possibility of water splashing.  
• Do not subject the faceplate to excessive shock, as it is  
a piece of precision equipment.  
Store unused batteries out of the reach of children. Contact  
a doctor immediately if the battery is accidentally swallowed.  
Do not set the remote on hot places such as above the  
dashboard.  
• The provided batteries are intended for use in operation  
checking, and their service life may be short.  
• When the remote controllable distance becomes short,  
replace both of the batteries with new ones.  
• When replacing a fuse, only use a new one with the  
prescribed rating. Using a fuse with the wrong rating  
may cause your unit to malfunction.  
• To prevent short circuits when replacing a fuse, first  
disconnect the wiring harness.  
• Do not use any screws except for the ones provided.  
The use of improper screws might result in damage to  
the main unit.  
• You cannot view video pictures whilst the vehicle is  
moving. To enjoy TV/video pictures, find a safe place to  
park and engage the parking brake.  
Cleaning the panel and monitor  
When the operator panel and monitor panels are dirty, wipe  
and clean them using a soft cloth (such as a commercially  
available silicon coated cloth). When contaminated  
excessively, clean them using a cloth dipped in a neutral  
detergent first, then remove the detergent using a dry cloth.  
Do not use a hard cloth and a volatile chemical (such as an  
alcohol). If used, the panel surface may be scratched or  
printed letters may be erased.  
Cleaning the disc slot  
NOTE  
As dust can accumulate in the disc slot, clean it  
occasionally. Your discs can get scratched if you put them  
in a dusty disc slot.  
• If you experience problems during installation, consult  
your Kenwood dealer.  
• If the unit does not seem to be working right, try  
pressing the reset button first. If that does not solve the  
problem, consult your Kenwood dealer.  
Lens Fogging  
Right after you turn on the car heater in cold weather, dew  
or condensation may form on the lens in the disc player of  
the unit. Called lens fogging, discs may be impossible to  
play. In such a situation, remove the disc and wait for the  
condensation to evaporate. If the unit still does not operate  
normally after a whilst, consult your Kenwood dealer.  
The marking of products using lasers (Except for  
some areas)  
Reset button  
CLASS 1  
LASER PRODUCT  
Screen brightness during low temperatures  
When the temperature of the unit falls such as during  
winter, the liquid crystal panel's screen will become darker  
than usual. Normal brightness will return after using the  
monitor for a whilst.  
The label is attached to the chassis/case and says that the  
component uses laser beams that have been classified as  
Class 1. It means that the unit is utilizing laser beams that  
are of a weaker class. There is no danger of hazardous  
radiation outside the unit.  
4 English  
Region codes in the world  
The DVD players are given a region code according to the country or area it is marketed, as shown in the following map.  
1
5
2
1
2
1
4
5
2
4
Icons on the DVD discs  
Icon  
Description  
Indicates the region code where the disc can be played.  
Number of voice languages recorded with the audio function. The number in the icon indicates the number  
of voice languages. (Max. 8 languages)  
8
Number of subtitle languages recorded with the subtitle function. The number in the icon indicates the  
number of subtitle languages. (Max. 32 languages)  
32  
Number of angles provided by the angle function. The number in the icon indicates the number of angles.  
(Max. 9 angles)  
9
Aspect ratios that can be selected. "LB" stands for Letter Box and “PS” for Pan/Scan. In the example on the  
left, the 16:9 video can be converted into letter box video.  
16:9 LB  
Unplayable discs  
This player cannot play back any of the following discs.  
• DVD-ROM/DVD-RAM discs  
• HQ-VCD discs  
• CDV discs (Only the audio part can be reproduced)  
• Photo CD discs  
• CD-G/CD-EG/CD-EXTRA discs (Only the audio can be reproduced)  
• DVD-Audio  
Also, you cannot play back the DVD-R/RW and DVD+R/RW discs if not recorded in the DVD-Video format.  
Restrictions due to difference between discs  
Explanation of icons used on this manual  
Some DVD and VCD discs can be played only in  
Inhibition  
icon  
Indicates the key operation on the receiver.  
certain playback modes according to the intentions  
of the software producers. As this player plays  
discs according to their intentions, some functions  
may not work as intended by you. Please be sure  
to read the instructions provided with each disc.  
When an inhibition icon is displayed on the  
Indicates the button you must touch.  
Indicates the key or joystick operation on the remote  
controller.  
monitor, it indicates that the disc being played is  
under the restriction as described above.  
The initial value of each setup is shown.  
The illustrations of the display and the panel appearing in this  
manual are examples used to explain more clearly how the  
controls are used. Therefore, what appears on the display in the  
illustrations may differ from what appears on the display on the  
actual equipment, and some of the illustrations on the display  
may represent something impossible in actual operation.  
Gives an additional information or an operation advice.  
Time is displayed on each control screen in the 12 hour clock display type (with AM/PM displayed) or in the 24 hour clock display type  
(without AM/PM displayed) depending on the sales area. The display type cannot be changed. In this instruction manual, screens of the  
24 hour display type are used as examples.  
English 5  
About discs  
Handling discs  
Removing discs  
• Don’t touch the recording surface of the disc.  
When removing discs from this unit pull them out  
horizontally.  
Discs that can’t be used  
• Discs that aren’t round can’t be used.  
• CD-R/RW, DVD-R/RW, and DVD+R/RW are easier to  
damage than a normal music CD. Use a CD-R/RW, DVD-  
R/RW, or DVD+R/RW after reading the caution items on  
the package etc.  
• Don’t stick tape etc. on the disc.  
Also, don’t use a disc with tape stuck on it.  
• Discs with coloring on the recording surface or that are  
dirty can’t be used.  
• This unit can only play the CDs with  
It may not correctly play discs which do not have the  
mark.  
• A CD-R or CD-RW that hasn’t been finalized can’t be  
played. (For the finalization process refer to your CD-  
R/CD-RW writing software, and your CD-R/CD-RW  
recorder instruction manual.)  
.
When using a new disc  
If the disc center hole or outside rim has burrs, use it after  
removing them with a ball pen etc.  
Burrs  
Disc storage  
• Don’t place them in direct sunlight (On the seat or  
dashboard etc.) and where the temperature is high.  
• Store discs in their cases.  
Burrs  
Disc accessories  
Don’t use disc type accessories.  
Disc cleaning  
Clean from the center of the disc and move outward.  
6 English  
Notes on playing MP3/WMA  
This unit can play MP3 (MPEG1 Audio Layer 3)/WMA.  
Note, however, that the MP3 recording media and  
formats acceptable are limited. When writing MP3, pay  
attention to the following restrictions.  
Entering file and folder names  
The code list characters are the only file names and folder  
names that can be entered and displayed.  
If you use any other character for entry, the file and folder  
names are not displayed correctly. They may neither be  
displayed correctly depending on the CD writer used.  
The unit recognizes and plays only those MP3/WMA which  
have the MP3 extension (.MP3/.WMA).  
Acceptable media  
The MP3/WMA recording media acceptable to this unit are  
CD-ROM, CD-R, and CD-RW.  
When using CD-RW, do full format not quick format to  
prevent malfunction.  
A file with a name entered with characters not on the code  
list may not play correctly.  
Writing files into a medium  
Acceptable medium formats  
When a medium containing MP3/WMA data is loaded, the  
unit checks all the data on the medium. If the medium  
contains a lot of folders or non-MP3/WMA files, therefore,  
it takes a long time until the unit starts playing MP3/WMA.  
In addition, it may take time for the unit to move to the  
next MP3/WMA file or a File Search or Folder Search may  
not be performed smoothly.  
The following formats are available for the media used in  
this unit. The maximum number of characters used for file  
name including the delimiter (".") and three-character  
extension are indicated in parentheses.  
• ISO 9660 Level 1 (12 characters)  
• ISO 9660 Level 2 (31 characters)  
• Joliet (64 characters)  
Loading such a medium may produce loud noise to damage  
the speakers.  
• Romeo (128 characters)  
• Do no attempt to play a medium containing a non-  
MP3/WMA file with the MP3/WMA extension.  
The unit mistakes non-MP3/WMA files for MP3/WMA data  
as long as they have the MP3/WMA extension.  
Up to 170 characters can be displayed in the long file name  
format. For a list of available characters, see the instruction  
manual of the writing software and the section Entering file  
and folder names below.  
The media reproducible on this unit has the following  
limitations:  
• Do not attempt to play a medium containing non  
MP3/WMA.  
• Maximum number of directory levels: 8  
• Maximum number of files per folder: 255  
• Maximum number of characters for folder name: 64  
• Maximum number of folders: 100  
MP3 written in the formats other than the above may not  
be successfully played and their file names or folder names  
are not properly displayed.  
MP3/WMA playing order  
When selected for play, Folder Search, File Search, or for  
Folder Select, files and folders are accessed in the order in  
which they were written by the CD writer.  
Because of this, the order in which they are expected to be  
played may not match the order in which they are actually  
played. You may be able to set the order in which  
MP3/WMA are to be played by writing them onto a  
medium such as a CD-R with their file names beginning  
with play sequence numbers such as "01" to "99",  
depending on your CD writer.  
Settings for your MP3/WMA encoder and CD  
writer  
Do the following setting when compressing audio data in  
MP3 data with the MP3/WMA encoder.  
• Transfer bit rate: MP3: 8 —320 kbps  
WMA: 48 —192 kbps  
• Sampling frequency: MP3: 32, 44.1, 48 kHz  
WMA: 32, 44.1, 48 kHz  
When you use your CD writer to record MP3/WMA up to  
the maximum disc capacity, disable additional writing. For  
recording on an empty disc up to the maximum capacity at  
once, check Disc at Once.  
Play mode may not be possible when portions of the  
functions of Windows Media Player 9 or higher are used.  
Entering ID3 tag  
The Displayable ID3 tag is ID3 version 1.x.  
For the character code, refer to the List of Codes.  
English 7  
DDX7035 Basic operations  
8 English  
Play Disc  
[Disc insertion slot]  
Track/Station Selectors  
[SEEK] key  
1
2
3
4
7
8
A disc is played when you insert it.  
Selects a music or chapter, track, or frequency.  
Play/Pause  
Attenuator/Loudness  
[ATT]/[LOUD] key  
[
] key  
38  
Pauses and replays a disc.  
Attenuates the volume.  
Press it again to cancel muting.  
Press it for more than one second to turn the Loudness  
function on or off. (see page 69)  
If turned on, high and low tones are enhanced during  
low volume.  
Eject Disc  
[EJECT] key  
The disc is ejected.  
Switch Video Sources  
[V.SEL] key  
Traffic Information  
[TI] key  
9
p
q
The video sources are switched each time you press  
the key.  
Turns the Traffic Information function On or Off. (see  
page 26)  
Screen Setup  
[SCRN] key  
Displays the Screen Control or Tilt Control screen. (see  
page 42)  
Function  
[FNC] key  
* Optional accessory  
Clears the video image when pressed more than one  
second. When pressed again, the original image is  
redisplayed.  
The video sources are switched each time you press  
the key.  
Switch Audio Source/Power Supply  
[SRC] key  
5
The audio sources are switched each time you press  
the key.  
Switches the source that is output at the AV OUTPUT  
terminal when it is pressed more than 1 second.  
Switch Screen Mode/GSM  
[MODE]/[GSM] key  
w
The screen mode is switched. (see page 14)  
The GSM Control screen appears when you hold down  
the key more than 1 second. (see page 78)  
* Optional accessory  
Hold down more than 1 second to turn the power  
supply Off.  
Push it again to turn power supply On.  
Volume Controls  
[VOL] key  
6
The display turns on when you put the parking brake,  
except for the navigation system.  
English 9  
DDX7045/7065 Basic operations  
AUTO  
10 English  
Play Disc  
[Disc insertion slot]  
Track/Station Selectors  
[SEEK] key  
1
2
3
4
7
8
A disc is played when you insert it.  
Selects a music or chapter, track, or frequency.  
Play/Pause  
Attenuator/Loudness  
[ATT]/[LOUD] key  
[
] key  
38  
Pauses and replays a disc.  
Attenuates the volume.  
Press it again to cancel muting.  
Press it for more than one second to turn the Loudness  
function on or off. (see page 69)  
If turned on, high and low tones are enhanced during  
low volume.  
Eject Disc  
[EJECT] key  
The disc is ejected.  
Switch Video Sources  
[V.SEL] key  
Select Seek Mode  
[AUTO] key  
9
p
q
The video sources are switched each time you press  
the key.  
Selects the Seek mode. (see pages 24/38 for the  
<Seek Mode>)  
Screen Setup  
[SCRN] key  
Displays the Screen Control or Tilt Control screen. (see  
page 42)  
Function  
[FNC] key  
* Optional accessory  
Clears the video image when pressed more than one  
second. When pressed again, the original image is  
redisplayed.  
The video sources are switched each time you press  
the key.  
Switch Audio Source/Power Supply  
[SRC] key  
5
The audio sources are switched each time you press  
the key.  
Switches the source that is output at the AV OUTPUT  
terminal when it is pressed more than 1 second.  
Switch Screen Mode/GSM  
[MODE]/[GSM] key  
w
The screen mode is switched. (see page 14)  
The GSM Control screen appears when you hold down  
the key more than 1 second. (see page 78)  
* Optional accessory  
Hold down more than 1 second to turn the power  
supply Off.  
Push it again to turn power supply On.  
Volume Controls  
[VOL] key  
6
The display turns on when you put the parking brake,  
except for the navigation system.  
English 11  
Basic Operations of Remote Controller  
Remote Control Mode selector  
[DISC]  
1
2
3
4
5
Selects one of the following remote control modes.  
TV: TV source  
DVD: Built-in DVD/VCD/CD/MP3/WMA player source  
AUD: Tuner source or attached disc changer/disc  
player source  
Stops to play the built-in disc player.  
Switches over the sound source each time it is  
pressed.  
Selects the Direct Search mode.  
(see pages 21/26/35/39 for <Direct Search>)  
Volume Control  
Adjusts the volume.  
12 English  
Joystick  
[DVD]  
[DISC]  
6
7
t
Select a folder or a disc.  
Enters your selection from the DVD Disc Menu.  
[TV]  
[DVD] [VCD]  
FM: Switches to TV1, TV2, or VIDEO.  
Returns to the previous screen when the DVD/VCD  
Disc Menu is used.  
[TUNER]  
FM: Switches to the FM1, FM2, or FM3 band.  
AM: Switches to the AM band.  
[DVD]  
8
9
Calls the Top menu of DVD Disc Menu.  
[DISC]  
y
Switch Video Sources  
[V.SEL] key (When is set to "TV")  
1
Selects a chapter, a track or a song.  
[TV]  
The video sources are switched each time you press  
the key.  
Select a channel.  
[TUNER]  
Selects a station.  
[DVD] [VCD]  
u
1 : Fast Backward (Rewind). The speed changes  
each time it is pressed.  
¡ : Fast Forward. The speed changes each time it is  
* Optional accessory  
pressed.  
[DVD]  
p
q
w
[TV] [TUNER]  
i
o
Calls the DVD Disc Menu.  
Call the stations from memory.  
:
[DVD]  
[DISC]  
Each time you press the button, the angle switches.  
Plays or pauses.  
[DVD] [VCD]  
[TV] [TUNER]  
Each time you press the button, the zoom ratio  
switches.  
Selects the Seek mode. (see page 24/38 for the <Seek  
Mode>)  
[DVD]  
e
r
[DVD]  
;
a
Switches a subtitle language.  
:
Slow Backward.  
: Slow Forward.  
[DVD]  
Switches an audio language.  
Attenuator  
[ATT] key  
Attenuates the volume.  
Press it again to cancel muting.  
[DVD]  
[VCD]  
[DISC]  
[TV]  
: An operation during DVD playback  
: An operation during VCD playback  
: An operation during DVD, VCD, CD, MP3/WMA or MD playback  
: An operation during TV source  
[TUNER]  
: An operation during FM/AM broadcasting source  
English 13  
Switch Screen Mode  
The Screen mode of the monitor changes each time the [MODE] key is pressed.  
[MODE] key  
Full picture mode [FULL]  
Justify picture mode [JUST]  
Cinema picture mode [CINEMA]  
Zoom picture mode [ZOOM]  
Normal picture mode [NORMAL]  
• When the Menu, Easy Control screen, or Navigation is selected, it is shown in the full-size display mode automatically.  
Their Screen mode cannot be changed.  
• The Screen mode can be set for each of DVD/VCD, TV, and video images.  
14 English  
English 15  
Control during DVD Video or Video CD Playback  
Control during DVD Video or Video CD Playback  
Various control screens appear when you play back a DVD Video (DVD) or a Video  
Displaying the DVD/VCD  
Playback screen  
You can use the following operations when displaying  
DVD/VCD images.  
Title Number Display  
Chapter Number Display  
Play Time Display  
1
2
3
4
Plays back the  
DVD or VCD.  
Forward Chapter Search Area  
Selects the next chapter.  
Backward Chapter Search Area  
Selects the previous chapter.  
5
6
DVD playback screen  
1
2
3
DVD VIDEO  
5
Title 1 Chap 3  
T
0:02:37  
DVD Disc Menu Control Buttons Area  
Displays the Disc Menu Control buttons. (see page  
20)  
MODE: FU L L AV-OUT: AV - I N  
6
4
Information Display Button Area (see page 21)  
7
7
DVD VIDEO  
Title 1 Chap 3  
T
0:02:37  
IN  
VCD playback screen  
Scene/Track Number Display  
8
9
DVD VCD  
PBC  
8
Scene 255  
P
2:37  
3
MODE: FU L L AV-OUT: AV - I N  
VER2  
Forward Scene/Track Search Area  
Selects the next scene (when PBC is On) or track  
(when PBC is Off).  
10  
9
11  
Backward Scene/Track Search Area  
Selects the previous scene (when PBC is On) or  
track (when PBC is Off).  
p
12  
Zoom Control Button Area  
Displays the Zoom Control buttons. (see page 21)  
DVD VCD  
Scene 255  
P
2:37  
q
w
IN  
Information Display Button Area (see page 21)  
• For DVD/VCD playback, DVD/VCD picture  
selection, or controller key operations, see  
<DDX7035/7045/7065 Basic Operations> (see  
page 8/10).  
• The information display is cleared automatically  
after approximately 5 seconds. Also, the  
information can be displayed automatically when  
it is updated (see page 61).  
16 English  
CD (VCD) disc.  
Displaying the Easy Control  
Panel  
The Control Panel is displayed in a floating position of the  
DVD/VCD screen.  
Switches the source.  
Stops to play.  
e
r
t
y
Rewinds or fast forwards.  
Chapter Search (DVD)  
Searches for a chapter.  
Scene/Track Search (VCD)  
Selects a scene (when PBC is On) or a track (when  
PBC is Off).  
Display of Easy Control Panel  
T i t l e  
1
MODE: FU L L AV-OUT: AV - I N  
C h a p  
3
T
0 : 0 5 : 3 2  
DVD VIDEO  
Plays or pauses.  
u
The Easy Control Panel display is cleared when you  
touch the center of image display area.  
15  
16  
13  
14  
15  
16  
17  
SRC  
DVD VIDEO  
T i t l e  
1
C h a p  
3
T
0 : 0 5 : 3 2  
IN  
English 17  
Control during DVD Video or Video CD Playback  
Displaying the DVD/VCD  
Control screen  
Ejects the disc from the built-in disc player.  
Calls the Sound Effects Menu. (see page 68)  
Calls the Setup Menu. (see page 43)  
i
o
;
a
s
d
Plays a DVD/VCD using various functions.  
Displays the Source Select screen. (see page 40)  
Fast Forwards or Rewinds.  
DVD/VCD Control screen  
Stops to play.  
DVD V I DEO  
When pressed twice, the disc is played from its  
beginning when you play it in the next time.  
1 3 : 5 0  
26  
26  
23  
Audio  
19  
20  
25  
24  
24  
Set Up  
Selects a chapter, a scene or a track.  
When the DVD is paused, touch this button to start  
single-frame stepping.  
f
Direct  
SRC  
22  
22  
21  
IN  
34  
PBC27 REP28  
Title Chap  
KENWOOD  
30  
SCRL29  
TIME  
Plays or pauses.  
g
h
31  
1
3
32  
T0:05:20  
33  
18  
Slow Forwards or Backwards. (during DVD playback  
only)  
T-REP  
35  
Turns the PBC function of VCD On or Off. (when  
VCD Ver 2.0 or SVCD is in use only)  
j
k
Switches the Repeat Play operations in the  
following sequence.  
DVD: Title Repeat, Chapter Repeat, Repeat Off  
VCD: Track Repeat, Repeat Off (Available when the  
PBC is off)  
Scrolls the display text.  
l
/
Switches the play time display in the following  
sequence.  
DVD: Title, chapter, remaining titles  
VCD: Track, disc, remaining discs (Effective only  
when the PBC function is off)  
Title Number Display (DVD)  
Chapter/Scene/Track Number Display  
Play Time Display  
z
x
c
v
b
Appears when a disc is inserted.  
Function Indicator  
18 English  
English 19  
Control during DVD Video or Video CD Playback  
DVD Disc Menu  
2
Select Disc Menu options  
Disc Menu  
Selects an option from the DVD Disc Menu.  
1
Displays the Disc Menu Control screen  
Menu  
C t r l  
DVD Disc Menu Control Buttons  
Area (page 16)  
Menu  
R e t u r n  
Menu  
C t r l  
Top  
3
5
1
6
Menu  
Audio  
1 / 1  
C t r l  
SUB  
1 0 / 1 0  
1
4
3
3
3
3
4
2
7
C a n c e l  
E n t e r  
E x i t  
5
6
2
Zoom  
A n g l e 1 / 1  
E x i t  
Calls the Menu.  
1
2
3
4
5
6
7
Returns to the Disc Menu Control screen.  
Selects a menu option.  
Calls the Menu Control.  
1
2
Switches the picture angle.  
Enters your menu selection.  
Returns to the previous menu screen.  
Displays the Top Menu.  
(during program playback only)  
Switches the caption language.  
(during program playback only)  
Switches the voice language.  
(during program playback only)  
Displays the Zoom Control screen.  
Clears the Disc Menu Control.  
3
4
Clears the Disc Menu Control.  
Zoom Control  
Zoom  
5
6
ZoomC t r l  
2
2
2
3
2
1
4
C a n c e l  
Zoom  
O f f  
E x i t  
Changes the zoom ratio at 4 levels (2 times, 3  
times, 4 times, or off) each time you touch.  
Scrolls the screen in the direction you touch.  
Returns to the Disc Menu Control screen.  
Clears the Disc Menu Control.  
1
2
3
4
20 English  
VCD Zoom Control  
Direct Search  
Displays an enlarged VCD screen.  
You can search for a DVD/VCD chapter, scene  
or track by entering its number.  
1
Displays the Zoom Control screen  
1
Selects the Direct Search mode  
Zoom Control Button Area  
(page 16)  
ZoomC t r l  
The following items can be searched directly each  
time it is pressed.  
2
DVD: Title, Chapter, Time, Direct number  
VCD (when PBC is On): Scene, Direct number  
VCD (when PBC is Off): Track, Time  
2
2
However, the direct search may not be supported for  
some discs.  
1
3
Zoom O f f  
E x i t  
2
2
3
Enter a number or time  
Changes the zoom ratio at 4 levels (2 times, 3  
times, 4 times, or off) each time you touch.  
1
Scrolls the screen in the direction you touch.  
Clears the Zoom Control button.  
2
3
Search  
Information Display  
Displays the DVD and AV information.  
The operation ends automatically if you do not  
operate within 10 seconds.  
Information Display Button Area  
(Page 16)  
The information is displayed for 5 seconds.  
English 21  
Tuner Control  
Tuner Control  
Various control screens appear in the Tuner Source mode.  
Displaying the Easy Control  
Panel  
The Tuner Control Panel is displayed in a floating position  
of the selected picture.  
Switches the source.  
1
2
3
4
Switches the band (to AM or FM1/2/3).  
Tunes in a station  
Switches the Seek mode.  
(see page 24 for the <Seek Mode>)  
Displaying the Easy Control Panel  
• For receiver key operations, see <DDX7035/  
7045/7065 Basic Operations> (see page 8/10).  
• The Easy Control Panel display is cleared when  
you touch the center of image display area.  
MODE: FU L L AV-OUT: AV - I N  
1
2
2
4
3
3
SRC  
TUNER  
A M F M  
P r e s e t  
SEEK  
9 8 . 1 M H z  
F M 1  
1
22 English  
Displaying the Tuner Control  
screen  
Calls the Tuner Menu.  
5
6
7
8
9
p
q
You can tune in a station using various functions.  
Calls the Sound Effects Menu. (see page 68)  
Displays the Source Select screen. (see page 40)  
Calls the Setup Menu. (see page 43)  
Switches to the FM1/2/3 band.  
Tuner Control screen  
Switches to the AM band.  
Tunes in a station.  
Use the <Seek Mode> to change the frequency  
switching.  
TUNER  
1 3 : 5 0  
5
9
Menu  
FM  
AM  
Audio  
6
8
11  
11  
Set Up  
Switches between  
1
to  
6
buttons and  
w
e
Direct  
SRC  
10  
7
Function buttons to use.  
17  
18  
12  
14  
15  
LO.S 13 AME SEEK DISP SCRL MONO  
16  
LO.S Turns the Local seek function On or Off.  
Next  
<Function of DDX7035>  
FM1  
21  
Preset  
1
98. 1 MHz  
Turns the CRSC function On or Off. (Only  
when receiving the FM broadcast) <Function of  
DDX7045/7065>  
CRSC  
AUTO 1  
20  
19  
1
2
3
4
5
6
Selects the Auto Memory mode.  
(See page 24 for the <Auto Memory>)  
r
t
y
Switches the Seek mode.  
(see page 24 for the <Seek Mode>)  
Selects the Program Service Name, or Radio Text  
mode for text display. (Only when receiving the FM  
broadcast) <Function of DDX7035>  
Scrolls the display text. <Function of DDX7035>  
u
i
Select the Monaural sound mode. (Only when  
receiving the FM broadcast) <Function of  
DDX7035>  
When  
1
to  
6
buttons appear, you can  
o
Displaying the Tuner Menu  
screen  
call up the stations from memory.  
For memory of broadcasting stations, see <Auto  
Memory> (see page 24) or <Manual Memory> (see  
page 24).  
You can select menu options using various functions.  
Seek Mode Indicator  
;
a
s
d
Memory Number Display  
Menu  
Selects options from various function menus.  
Returns to the Tuner Control screen.  
Tuner Menu screen  
22  
The available functions vary depending on the  
model used (the tuner specifications and the  
broadcasting system that can be received).  
P r e s e t Se l e c t  
PTY Sea r c h  
Rad i o T e x t  
TUNER  
Audio  
Set Up  
SRC  
23  
English 23  
Tuner Control  
Seek Mode  
Manual Memory  
Sets a station selection.  
Stores the current receiving station in memory.  
1
Select a station you wish to store in memory  
FM  
AM  
SEEK  
Next  
If SEEK is not shown, touch  
.
The mode is switched each time you touch the  
button.  
2
Store in memory  
Tunes in a station with good  
reception automatically.  
1
6
AUTO 1  
Next  
If  
1
to  
6
are not shown, touch  
.
Tune in stations in memory one  
after another.  
AUTO 2  
Continue to touch until the memory number appears.  
Switches to the next channel  
manually.  
MANUAL  
Auto Memory  
Stores stations with good reception in memory  
automatically.  
1
Select a band you wish to store in memory  
FM  
AM  
2
Select the Auto Memory mode  
AME  
Next  
If AME is not shown, touch  
.
3
Start Auto Memory  
Touch  
or  
.
Auto Memory terminates when 6 stations are stored  
or when all stations are tuned in.  
The operation ends automatically if you do not  
operate within 10 seconds.  
24 English  
Function of DDX7045/7065  
Preset Select  
Set Station Name  
Lists and tunes in stations in memory one after  
the other.  
Names a station.  
Call the Tuner Menu  
1
2
3
Tune in a station you wish to name  
1
FM  
AM  
Menu  
Call the Tuner Menu  
2
Call the Preset Select Menu  
Menu  
P r e s e t Se l e c t  
Selects the Set Name mode  
Name Se t  
1
TUNER  
FM3 1) 100. 5 Mhz  
4
Menu  
Audio  
FM3 2) 100. 5 Mhz  
FM3 3) 100. 5 Mhz  
FM3 4) 100. 5 Mhz  
FM3 5) 100. 5 Mhz  
FM3 6) 100. 5 Mhz  
Set Up  
SRC  
2
2
4
5
Enter a name  
3
FM  
98.1  
For character entry details, see <Character Entry>  
(see page 41).  
Tunes in the displayed station.  
1
If the station name is displayed if it has been set.  
(DDX7045/7065)  
Exit the Set Name mode  
Switches the band of the displayed station list.  
2
3
4
Band Display.  
Ok  
Returns to the Tuner Menu.  
• You can store up to 30 stations in memory.  
• You can set a station name only after you have  
applied the parking brake.  
English 25  
Tuner Control  
Function of DDX7035  
Direct Search  
Traffic Information  
Tunes in a station when its frequency is  
entered.  
When a traffic bulletin starts, any source is  
switched to the traffic information and it is  
displayed automatically.  
1
2
3
Select a band  
When the traffic bulletin starts...  
The Traffic Information screen appears automatically.  
Traffic Information screen  
Selects the Direct Search mode  
1 3 : 5 0  
T U N E R  
1
Audio  
Set Up  
2
Direct  
SRC  
Enter a frequency  
Traffic Infomation  
Calls the Sound Effects Menu. (see page 68)  
Calls the Setup Menu. (see page 43)  
1
2
When you enter them, signal reception starts.  
Example: When you receive FM 92.1 MHz  
During reception of traffic information the  
adjusted volume is automatically remembered,  
and the next time it switches to traffic  
information it's automatically the remembered  
volume.  
Example: When you receive AM 810 kHz  
The operation ends automatically if you do not  
operate within 10 seconds.  
Please note that if DSP unit (optional accessory)  
is connected, the volume will be preset by  
pressing the  
button for 2 seconds or more.  
26 English  
Function of DDX7035  
Function of DDX7035  
Search for Program Type  
Radio Text  
A program is tuned when you set its program  
type.  
You can display the radio text.  
1
Call the Tuner Menu  
1
Call the Tuner Menu  
Menu  
Menu  
2
Display the Radio Text  
2
Call the PTY Search Menu  
Rad i o T e x t  
PTY Sea r c h  
TUNER  
Menu  
1
2
1
Rad i o t e x t :  
Audio  
TUNER  
A l l S p e e c h  
Set Up  
SRC  
Audio  
A l l M u s i c  
Set Up  
2
Direct  
SRC  
N e w s  
C u r r e n t A f f a i r s  
I n f o r m a t i o n  
2
SRCH  
3
4
FM  
98.1  
Re t u r n  
Not Found  
Displays the Radio Text  
1
2
Returns to the Tuner Menu.  
Selects a program type.  
1
2
3
Scrolls the program type list.  
Searches for the program type.  
It is displayed when the Program Type is selected.  
Returns to the Tuner Menu.  
4
3
4
Select a program type  
N e w s  
etc.  
Search for the program type  
SRCH  
English 27  
CD/MP3/WMA/Disc Changer Play Control  
CD/MP3/WMA/Disc Changer Play Control  
You can call various control screens during CD/MP3/WMA/Disc Changer playback.  
Displaying the Easy Control  
Panel  
The CD/MP3/WMA/Disc Changer Play Control Panel is  
displayed in a floating position of the selected picture.  
Switches the source.  
1
2
3
Stops to play the built-in disc player.  
When a CD is played back on the built-in disc player:  
Rewinds or fast forwards.  
Selects a song.  
Plays or pauses.  
4
5
6
Display of Easy Control Panel  
During CD playback  
When an MP3/WMA is played back on the built-in  
disc player:  
Selects a folder.  
DVD CD  
MODE: FU L L AV-OUT: AV - I N  
When a disc is played back on the disc changer:  
Selects a disc.  
7
• For CD/MP3/WMA/Disc Changer playback and  
receiver key operations, see <DDX7035/  
7045/7065 Basic Operations> (see page 8/10).  
2
4
1
3
3
4
5
SRC  
DVD CD  
T r a c k  
3
P
5 : 3 2  
• The Easy Control Panel display is cleared when  
you touch the center of image display area.  
IN  
During MP3/WMA playback  
5
6
4
4
6
2
SRC  
DVD MP3/WMA  
+
¡
3
1
P
0 : 0 5 : 3 2  
IN  
During playback on disc changer  
5
4
4
7
7
SRC  
CD CH  
D
-
D
T 3  
+
D 1  
P
5 : 3 2  
IN  
During playback on CD player  
4
4
5
SRC  
CD  
T 3  
P
5 : 3 2  
IN  
28 English  
Displaying the CD/MP3/WMA/  
Disc Changer Control screen  
During CD playback  
You can play the CD/MP3/WMA/disc changer using  
various functions.  
Calls the CD Menu.  
8
9
p
q
w
e
r
t
y
Calls the Sound Effects Menu. (see page 68)  
Displays the Source Select screen. (see page 40)  
Calls the Setup Menu. (see page 43)  
Ejects the disc from the built-in disc player.  
Selects a track.  
CD Control screen  
DVD CD  
1 3 : 5 0  
8
25  
Menu  
Fast Forwards or Rewinds.  
Audio  
9
15  
13  
13  
Set Up  
11  
Plays or pauses.  
Direct  
SRC  
14  
17  
14  
10  
IN  
24  
Starts or stops Scan Play (that plays the beginning  
of each song one after the other).  
16  
18  
21  
19  
20  
SCRL  
SCN  
22  
DISP  
2:09  
REP RDM  
TIME  
Repeats to play (the present track).  
u
i
23  
Track  
4
P
12  
Starts or stops Random Play (to play songs in  
random order).  
REP  
26  
Selects the Disc Name (see <Set Disc Name>, page  
33), Disc Text, or Track Text mode for text display.  
o
Scrolls the display text.  
;
a
Switches the play time display between Track, Disc,  
and Disc Remaining Time.  
Track Number Display  
Play Time Display  
s
d
f
g
Appears when a disc is inserted.  
Stops to play the built-in disc player.  
When pressed twice, the disc is played back from  
its beginning in the next time.  
Function Indicator  
h
English 29  
CD/MP3/WMA/Disc Changer Play Control  
MP3/WMA Control screen  
During MP3/WMA play  
DVD MP3/WMA  
Menu  
1 3 : 5 0  
29  
27  
32  
32  
Calls the MP3/WMA Menu.  
Fast Forwards.  
j
k
l
+
-
Audio  
31  
30  
30  
Set Up  
Direct  
SRC  
Stops to play.  
When pressed twice, the disc is played back from  
its beginning in the next time.  
28  
IN 42  
38  
33  
34  
PEP  
35  
36  
37  
Next  
SCN  
RDM  
40  
DISP  
SCRL  
0:00:38  
41  
44  
¡
3
1
P
Selects a song.  
Plays or pauses.  
Selects a folder.  
/
z
x
c
KENWOOD  
REP  
43  
FREP39  
Starts or stops Scan Play (that plays the beginning  
of each song one after the other).  
Repeats to play (the present song).  
v
b
Starts or stops Random Play (to play songs of the  
present folder in random order).  
Selects the Folder name, File name, Title (ID3/WMA  
tag), Artist name (ID3/WMA tag), or Album name  
(ID3 tag) for text display.  
n
Scrolls the display text.  
m
,
.
P
Q
W
E
R
Switches the button display.  
Repeats to play the song of the present folder.  
Folder and File Number Display  
Play Time Display  
Appears when a disc is inserted.  
Function Indicator  
Ejects a disc.  
30 English  
Disc Changer/CD player Control screen  
During play by the disc changer/CD player  
CD- CH  
1 3 : 5 0  
45  
47  
Calls the Disc Changer/CD player Menu.  
T
Y
Menu  
+
Disc  
Audio  
46  
48  
Selects a track.  
46  
Set Up  
Starts Fast Forward or Fast Rewind when it is held  
down.  
Direct  
SRC  
47  
-
Disc  
54  
57  
DISP 55 SCRL  
49  
50  
51  
56  
Selects a disc. (Function of Disc Changer)  
Plays or pauses.  
U
I
O
Next  
TIME  
SCN  
REP RDM  
59  
D1  
T5  
P
1:24  
60  
58  
Starts or stops Scan Play (that plays the beginning  
of each song one after the other).  
REP  
61  
DREP52 MRDM53  
Repeats to play (the present track).  
:
A
Starts or stops Random Play (to play songs in  
random order).  
Repeats to play disc (the present disc). (Function of  
Disc Changer)  
S
D
Starts or stops Magazine Random Play (to play  
songs of the disc changer in random order).  
(Function of Disc Changer)  
Switches the button display.  
F
G
Selects the Disc Name (see <Set Disc Name>,  
page 33), Disc Text, or Track Text mode for text  
display.  
Scrolls the display text.  
H
J
Switches the play time display between Track, Disc,  
and Disc Remaining Time.  
Disc Number Display (Function of Disc Changer)  
Track Number Display  
K
L
Play Time Display  
Function Indicator  
The functions that can be used and the information  
that can be displayed will differ depending on the  
models being connected.  
English 31  
CD/MP3/WMA/Disc Changer Play Control  
Displaying the CD/MP3/WMA/  
Disc Changer Menu screen  
Selects options from various function menus.  
You can select menu options using various functions.  
Returns to the CD/MP3/WMA/Disc Changer Control  
screen.  
Menu  
CD Menu screen  
62  
Name Set  
DVD CD  
Audio  
Set Up  
SRC  
63  
The available functions vary depending on the  
source used.  
32 English  
Set Disc Name  
Directory List (during  
MP3/WMA play)  
Names a CD.  
The directory of an MP3/WMA disc are listed  
for quick search.  
1
2
Play a CD you wish to name  
Call the CD/Disc Changer Menu  
1
Call the MP3/WMA Menu  
Menu  
Menu  
3
Select the Set Name mode  
2
Start the Directory List  
Name Set  
Directory List  
Name Set  
The  
position varies  
depending on the disc you are playing.  
Fo l d e r Name  
MP3/WMA  
Menu  
Audio  
3
4
5
Fo l d e r Name  
Fo l d e r Name  
F i l e Name  
7
Set Up  
SRC  
7
4
5
Enter a name  
1
2
Fol  
Root  
For character entry details, see <Character Entry>  
(see page 41).  
F i l e Name  
6
Open  
0:35:27  
F i l e Name  
Exit the Set Name mode  
Returns to the root directory.  
1
2
3
Displays the next higher level of hierarchy.  
Displays a directory if the subdirectory has a  
Ok  
directory. When you touch the directory, it opens.  
Displays a directory if the subdirectory has files  
without a directory. When you touch the directory,  
it opens and songs in the directory are played.  
Displays the MP3/WMA files. When you touch a  
file, its song is played back.  
4
5
• You cannot name an MD or MP3/WMA disc.  
• Number of discs that can be stored in memory  
Built-in disc player: 10  
External CD changer/ player:  
Varies depending on the CD changer/ player.  
Refer to the CD changer/ player manual.  
Plays the selected directory.  
6
7
Scrolls the list.  
3
Select a song  
F i l e Name  
Display the desired song and touch the file display.  
English 33  
CD/MP3/WMA/Disc Changer Play Control  
ID3/WMA TAG Display (during Disc Select (during play by  
MP3/WMA play)  
disc changer)  
The ID3/WMA TAG information of MP3/WMA  
file is listed.  
The discs loaded on the disc changer are listed  
for quick disc selection.  
1
2
Call the MP3/WMA Menu  
1
2
Calls the Disc Changer Menu  
Menu  
Menu  
Display the ID3/WMA TAG  
Call the Disc Select Menu  
Information  
Disc Select  
1
MP3  
CD- CH  
Menu  
1. D i s c Name  
2. D i s c Name  
3. D i s c Name  
4. D i s c Name  
5. D i s c Name  
6. D i s c Name  
Menu  
TITLE:  
Audio  
Audio  
2
Set Up  
Set Up  
DISP  
ARTIST:  
ALBUM:  
3
1
1
SRC  
SRC  
3
P
2:35  
Scrolls the list.  
Plays the displayed disc.  
1
1
2
Selects the Disc Name or Disc Text mode for text  
display.  
Scrolls the list.  
3
(It is not displayed when a disc changer having 6  
or less discs is used.)  
3
Select the desired disc  
1. D i s c Name  
Touch the desired disc display.  
34 English  
Direct Search  
Searches for a disc or a song when its number  
is entered.  
During play on the built-in disc player  
1
Select the Direct Search mode  
The following items can be searched directly each  
time it is pressed.  
CD: Track number, Total play time  
MP3/WMA: Folder, File  
2
3
Enter a disc or track number  
Search  
When searching for a song:  
During play on an external in disc player or disc  
changer  
1
Enter a disc or track number  
2
Search  
When searching for a song:  
When searching for a disc:  
The operation ends automatically if you do not  
operate within 10 seconds.  
English 35  
TV Control  
TV Control (with the optional accessory TV Tuner connected only)  
Various control screens appear in the TV Source mode.  
Displaying the TV Picture  
screen  
TV Band Number Display  
1
2
3
4
5
Various control screens appear in the TV Source mode.  
TV Area Group Display (see page 64)  
Memory Number Display  
Selects the  
TV Pictures.  
Channel Number Display  
Channel Up Area  
Increase the channel.  
TV Picture screen  
2
MODE: FU L L  
3
AV-OUT: AV - I N  
Group 1  
1
Preset 3  
4
2 c h  
T V 1  
6
Channel Down Area  
Decrease the channel.  
6
7
8
5
7
Band/Video Switch Area  
Switches to TV1, TV2, or VIDEO.  
8
Information Display Button Area  
• For receiver key operations, see <DDX7035/  
7045/7065 Basic Operations> (see page 8/10).  
TV  
Group 1  
Preset 3  
2 c h  
T V 1  
• The information display is cleared automatically  
after approximately 5 seconds. Also, the  
information can be displayed automatically when  
it is updated (see page 61).  
Displaying the Easy Control  
Panel  
The Control Panel is displayed in a floating position of the  
TV picture.  
Switches the source.  
9
p
q
w
e
Switches to Video (VIDEO).  
Switches the TV band (to TV1 or TV2).  
Calls up a channel.  
Switches the Seek mode.  
(see page 38 for the <Seek Mode>)  
Displaying the Easy Control Panel  
The Easy Control Panel display is cleared when you  
touch the center of image display area.  
T V 1  
MODE: FU L L AV-OUT: AV - I N  
VID10 T V11  
Group 1  
12  
12  
13  
9
SRC  
TV  
SEEK  
Preset 3  
2 c h  
T V 1  
36 English  
Displaying the TV Control  
screen  
Calls the TV Menu.  
r
t
y
u
i
o
;
You can tune in a TV station using various functions.  
Calls the Sound Effects Menu. (see page 68)  
Displays the Source Select screen. (see page 40)  
Calls the Setup Menu. (see page 43)  
Switches to VIDEO.  
TV Control screen  
Switches to TV1 or TV2.  
TV  
1 3 : 5 0  
14  
18  
Select a channel.  
Use the <Seek Mode> (see page 38) to change the  
channel tuning sequence.  
Menu  
VIDEO  
15  
Audio  
20  
20  
17  
Set Up  
Direct  
SRC  
16  
19  
Switches between  
1
to  
6
buttons and  
a
s
TV  
AME22 SEEK  
23  
21  
Function buttons to use.  
Next  
TV  
1
26  
Group  
1
Preset  
3
27  
2
ch  
Selects the Auto Memory mode.  
(see page 38 for the <Auto Memory>)  
AUTO 1  
25  
Switches the Seek mode.  
(see page 38 for the <Seek Mode>)  
d
f
24  
1
2
3
4
5
6
When  
1
to  
6
buttons appear, you can  
call up the channels from memory.  
For memory of broadcasting stations, see <Auto  
Memory> (see page 38) or <Manual Memory> (see  
page 38).  
Seek Mode Indicator  
g
h
j
TV Area Group Display (see page 64)  
Memory Number Display  
Displaying the TV Menu  
screen  
Selects options from various function menus.  
Returns to the TV Control screen.  
k
l
You can select menu options using various functions.  
Menu  
The available functions vary depending on the  
model used (the tuner specifications and the  
broadcasting system that can be received).  
TV Menu screen  
28  
P r e s e t Se l e c t  
Name Set  
TV  
Audio  
Set Up  
SRC  
29  
English 37  
TV Control  
Seek Mode  
Manual Memory  
Sets a TV station selection.  
Stores the current receiving channel in  
memory.  
SEEK  
1
Select a channel you wish to store in memory  
TV  
Next  
If SEEK is not shown, touch  
.
The mode is switched each time you touch the  
button.  
2
Store in memory  
Tunes in a station with good  
reception automatically.  
AUTO 1  
1
6
Tune in stations in memory one  
after another.  
Next  
AUTO 2  
If  
1
to  
6
are not shown, touch  
.
Continue to touch until the memory number appears.  
Switches to the next channel  
manually.  
MANUAL  
Preset Select  
Lists and tunes in stations in memory one after  
the other.  
Auto Memory  
Select a band you wish to call  
1
2
3
Stores stations with good reception in memory  
automatically.  
TV  
1
Select a band you wish to store in memory  
Call the TV Menu  
TV  
Menu  
(P 37  
)
r
2
Select the Auto Memory mode  
Call the Preset Select Menu  
AME  
P r e s e t Se l e c t  
Next  
If AME is not shown, touch  
.
3
Start Auto Memory  
1
TV1 1) 1ch  
TV1 2) 1ch  
TV1 3) 1ch  
TV  
2 Menu  
Audio  
Set Up  
SRC  
TV1 4) 1ch  
TV1 5) 1ch  
TV1 6) 1ch  
Touch  
or  
.
Auto Memory terminates when 6 stations are stored  
or when all stations are tuned in.  
TV  
3ch  
The operation ends automatically if you do not  
operate within 10 seconds.  
Tunes in the displayed station.  
If the station name is displayed if it has been set.  
Returns to the TV Menu.  
1
2
38 English  
Set Station Name  
Names a station.  
1
2
3
Select a station you wish to name  
TV  
Call the TV Menu  
Menu  
Selects the Set Name mode  
Name Set  
4
5
Enter a name  
For character entry details, see <Character Entry>  
(see page 41).  
Exit the Set Name mode  
Ok  
• You can store up to 20 stations in memory.  
• You can set a station name only after you have  
applied the parking brake.  
English 39  
Source Select  
Source Select  
The source you wish to listen to can be selected quickly.  
Displaying the Control screen  
Press this key several times unit the Control screen  
appears.  
Control screen  
DVD V I DEO  
1 3 : 5 0  
Audio  
Set Up  
Direct  
SRC  
IN  
SCRL  
T0:05:20  
TIME  
REP  
Chap  
KENWOOD  
Title  
1
3
The Source Select screen can be displayed from  
the control screen of any source.  
T-REP  
Displaying the Source Select  
screen  
Select the source.  
1
2
Returns to the Control screen previously displayed.  
Direct  
SRC  
Source Select screen  
1
STANDBY  
Audio  
TUNER  
Set Up  
DVD  
2
SRC  
VIDEO  
CD CH  
MD CH  
40 English  
Mute Telephone  
Character Entry  
Mute Telephone  
How To Use the Character  
Entry screen  
When the telephone is called, the system is  
paused automatically.  
When you select the Set Disc Name mode or  
others, the following screen appears for  
character entry.  
When the telephone is called...  
The Phone Call ("CALL") screen appears, and system  
is paused.  
Character Entry screen  
1
1
KENWOOD  
Phone Call ("CALL") screen  
a
h
o
v
3
b
i
c
j
d
k
r
e
l
f
m
t
g
n
u
1 3 : 5 0  
C A L L  
Audio  
4
4
Set Up  
p
w
q
x
s
z
Direct  
SRC  
y
2
Space  
Ok  
5
Shifts the cursor.  
Enters a space.  
1
2
If you erase a character, locate the cursor on it  
and touch this button.  
Enters characters.  
If you continue to listen the source audio  
during phone call...  
3
4
5
Displays respective character entry screens.  
Exits the Character Entry mode and returns to the  
previous screen.  
You can enter characters only after you have  
applied the parking brake.  
The system restarts to play while the phone call is  
continued.  
When the call ends...  
Hang up the phone.  
The system restarts to play.  
English 41  
Adjusting the Monitor Display Position and Quality  
Adjusting the Monitor Display Position and Quality  
You can adjust the position and picture quality of the monitor.  
Displaying the Screen Control  
screen  
You can adjust the picture quality using the following  
keys.  
Brightness Control  
1
2
Tint Control  
Displayed for an NTSC system image on TV or  
Video.  
Color Control  
3
Displayed on the TV and Video screen only.  
Screen Control screen  
Contrast Control  
4
5
6
Black Level Adjustment  
1
Displays the Adjust Monitor Position screen.  
1
(see Displaying the Tilt Adjust screen>, page 42)  
<
2
3
2
3
6
Tilt  
Returns to the previous screen.  
7
4
The Screen Control screen is displayed only when  
you have applied the parking brake.  
4
5
7
5
OK  
Displaying the Tilt Adjust  
screen  
Monitor Tilt Adjustment  
8
9
p
q
You can set the monitor tilt.  
The monitor fully closes.  
Returns to the Screen Control screen.  
Returns to the previous screen.  
Tilt  
Tilt Adjust screen  
If you turn the power off, the panel will close.  
However, if you turn the power back on, it will  
return to the adjusted tilt.  
T i l t A d j u s t  
10  
S c r e e n  
T i l t  
8
1
2
3
4
5
6
9
F u l l C l o s e  
11  
OK  
42 English  
Setup Menu  
Setup Menu  
You can set up various receiver parameters.  
Displaying the Control screen  
Press this key several times until the Control screen  
appears.  
Control screen  
DVD V I DEO  
1 3 : 5 0  
Audio  
Set Up  
Direct  
SRC  
IN  
SCRL  
T0:05:20  
TIME  
REP  
Chap  
KENWOOD  
Title  
1
3
You can call the same Setup Menu for the Control  
screen of each source.  
T-REP  
Displaying the Setup Menu  
screen  
Scrolls the Setup Menu.  
1
2
3
4
Calls each Setup Menu.  
Set Up  
Calls the Sound Effects Menu. (see page 68)  
Returns to the Control screen of the previous  
source.  
Setup Menu screen  
2
• Your setup on the <Sound Effects Menu> is  
adjusted automatically according to your <Audio  
Set Up> (see page 46) on the Setup menu. We  
recommend you to complete the <Audio Set Up>  
first, then set up the <Sound Effects Menu>.  
Set Up  
3
Audi o S e t Up  
DVD SETUP  
Audio  
Set Up  
Sys t em S e t U p  
AV I / F S e t Up  
User I / F S e t Up  
1
1
SRC  
4
• The available functions vary depending on the  
model used (the tuner specifications and the  
broadcasting system that can be received).  
English 43  
Setup Menu  
Audio Set Up  
You can setup a speaker network, etc.  
Displaying the Audio Set Up  
screen  
Returns to the Control screen of the previous  
source.  
1
Calls the Sound Effects Menu. (see page 68)  
Calls the Setup Menu.  
2
3
4
5
Audi o S e t Up  
Displays the X'Over setup screen. (see page 45)  
Speaker setup screen  
Sets up the front speaker type to fine-tune for the  
optimal equalizer curves.  
Standard: Setup for general diameter speakers  
Narrow: Setup for small diameter speakers  
Middle: Setup for small diameter woofer  
3
Menu  
4
Audio  
2
X' Ov e r  
Set Up  
SRC  
1
5
Fr o n t L&R  
Standard  
Wide:  
Setup for large diameter woofer  
5
Speaker  
44 English  
Crossover Network Setup  
You can set a crossover frequency of speakers.  
(P 44  
)
4
X' Ov e r  
X'Over setup screen  
X' Over  
HPF Front FREQ  
1
1
THR  
HPF Rear FREQ  
THR  
LPF SUB FREQ  
THR  
2
3
2
3
4
Rev e r s e  
Return  
5
Sets a Front High Pass Filter frequency.  
1
2
3
4
5
You can select any of the following frequency.  
Through, 40, 60, 80, 100, 120, 150, 180, 220 Hz  
Sets a Rear High Pass Filter frequency.  
You can select any of the following frequency.  
Through, 40, 60, 80, 100, 120, 150, 180, 220 Hz  
Sets a Sub woofer Low Pass Filter frequency.  
You can select any of the following frequency.  
50, 80, 120, Through Hz  
Sets the phase of subwoofer output.  
The phase is reversed 180 degrees when set to  
"Reverse".  
Returns to the Speaker setup screen.  
English 45  
Setup Menu  
Audio Set Up (with the optional accessory DSP unit connected only)  
You can set up more detailed settings by connecting the optional accessory DSP  
Displaying the Car Type Set Up  
screen  
If your vehicle type is selected, the Digital Time  
Alignment is set automatically (for timing adjustment of  
sound output for each channel) to have the highest  
surround effects.  
Returns to the Control screen of the previous  
source.  
1
Calls the Sound Effects Menu. (see page 68)  
Calls the Setup Menu.  
2
3
4
5
Sets up the car type you use together with this unit.  
Audi o S e t Up  
Displays the DTA (Digital Time Alignment) Setup  
screen. (see page 48)  
You can adjust the digital time alignment that was  
set automatically when you selected the car type.  
Car Type Set Up screen  
Displays the Speaker Set Up screen.  
6
3
5
Menu  
DTA  
Audio  
2
1
Set Up  
Car Type  
You cannot set up "Car Type" when "Position" (see  
page 76) is "ALL".  
4
4
Sma l l  
SRC  
Car Type  
6
46 English  
unit.  
Displaying the Speaker Set Up  
screen  
When the speaker type and size are set, the speaker  
crossover network and equalizer curve are set  
automatically.  
Displays the X'over (HPF) screen.  
(See <High Pass Filter Setup>, page 50)  
7
8
9
Display the X'over (LPF) screen.  
(See <Low Pass Filter Setup>, page 50)  
Sets up the front speaker type to fine-tune for the  
optimal equalizer curves.  
Standard: Setup for general diameter speakers  
Narrow: Setup for small diameter speakers  
Middle: Setup for small diameter woofer  
Speaker Set Up screen  
Wide:  
Setup for large diameter woofer  
7
X' Ov e r HPF  
Select the speakers for Multi-channel sounds.  
"3/2": Center speaker, Front speaker, Rear speaker  
"2/2": Front speaker, Rear speaker  
"3/0": Center speaker, Front speaker  
"2/0": Front speaker  
p
Menu  
Audio  
8
X' Ov e r LPF  
Set Up  
10Mu l t i Channel  
3 / 2  
10  
SRC  
Fr o n t L&R  
9
9
Standard  
11  
Set the use or no use of Sub Woofer.  
Displays the Channel Level Setup screen.  
Displays the Car Type Set Up screen.  
q
w
e
Sub Woo f e r  
O f f  
13  
Speaker  
12  
• "X’Over HPF" and "X’Over LPF" can be set only  
when "Sub Woofer" is set to "On".  
• "Multi Channel" can be set only when "Dolby Pro  
Logic" (see page 75) is set to "On".  
Displaying the Channel Level  
screen  
Selects a speaker to be set.  
(see <Channel Level>, page 48)  
r
t
y
u
You can set the volume at each setup position.  
Sets the speaker volume.  
(see <Channel Level>, page 48)  
Starts or stops test signal tone output for setup  
check.  
Channel Level screen  
Displays the Speaker Set Up screen.  
14  
Menu  
Audio  
• Your setup on the <Sound Effects Menu> is  
adjusted automatically to get the best sound  
effects according to the car type and speaker you  
have set on the <Audio Set Up> (see page 46).  
We recommend you to complete the <Audio Set  
Up> first, then set up the <Sound Effects  
Menu>.  
You can fine-adjust the automatic set value by  
<DTA Setup> (see page 48) or <Parametric  
Equalizer> (see page 72).  
16  
Set Up  
SRC  
Test  
Cent er  
15  
15  
+1 0dB  
17  
Chann e l L e v e l  
• Stop the test signal tone if you have finished  
setting up the Channel Level. If you leave the test  
signal tone on, you may not be able to set up  
other settings.  
English 47  
Setup Menu  
Channel Level  
DTA Setup  
Set the volume at each setup position.  
Manually set the sound output timing of each  
channel.  
Select a speaker you wish to adjust  
1
Display the DTA Setup screen  
1
(P46  
)
5
DTA  
Channel Level setup screen  
DTA Setup screen  
5
Menu  
2
4
1
Audio  
DTA  
1
Set Up  
3
Test  
Pr e s e t  
SRC  
3
Cent er  
+1 0dB  
Front  
2
2
1 m  
Chann e l L ev e l  
4
Return  
Left front speaker  
Right front speaker  
Left rear speaker  
Right rear speaker  
Center speaker  
1
2
3
4
5
Selects a speaker to be adjusted.  
1
2
Sets the distance between the selected speakers  
to adjust delay time.  
Stores the adjusted status in memory or calls it  
from memory.  
3
4
Returns to the Car Type Set Up screen.  
Adjust the volume  
2
Select a speaker you wish to adjust  
2
4
1
2
1
2
3
Front speaker  
1
2
3
4
Rear speaker  
Subwoofer  
Center speaker  
48 English  
Set a delay time  
3
The speakers are virtually moved to the desired  
distance.  
When the values of center speaker and front  
speakers increase, they are virtually moved forward.  
When the values of rear speakers and subwoofer  
increase, they are virtually moved backward.  
Store or call your setup into/from memory  
To store your setup in memory  
Pr e s e t  
Continue to touch more than 2 seconds.  
To call your setup from memory  
Pr e s e t  
English 49  
Setup Menu  
High Pass Filter Setup  
Low Pass Filter Setup  
You can manually set a High Pass Filter of  
Crossover Network.  
You can manually set a Low Pass Filter of  
Crossover Network.  
(P47  
)
(P47  
)
8
7
X' Ov e r HPF  
X' Ov e r LPF  
HPF F r ont  
100 Hz  
HPF Rear  
100 Hz  
1
2
1
2
3
100 Hz  
100 Hz  
5
6
1
2
1
3
4
3
4
5
Rev e r s e  
6
2
4
Sets a crossover frequency of Front High Pass  
Filter.  
Sets a crossover slope of Front High Pass Filter.  
Sets a crossover frequency of Rear High Pass  
Filter.  
Sets a crossover frequency of Low Pass Filter.  
Sets a crossover slope of Low Pass Filter.  
1
1
2
3
2
3
Sets the phase of subwoofer output.  
The phase is reversed 180 degrees when set to  
"Reverse".  
Sets a crossover slope of Rear High Pass Filter.  
Sets a crossover frequency of Center High Pass  
Filter.  
Returns to the Speaker Set Up screen.  
4
5
4
Sets a crossover slope of Center High Pass Filter.  
Returns to the Speaker Set Up screen.  
6
7
"HPF Center" can be set only when "Multi  
Channel" (see page 61) is set to "3/2" or "3/0".  
50 English  
English 51  
Setup Menu  
DVD Setup  
You can set up the DVD play.  
Displaying the DVD SETUP 1  
screen  
Returns to the Control screen of the previous  
source.  
1
DVD SETUP  
Calls the Sound Effects Menu. (see page 68)  
2
3
4
Calls the Setup Menu.  
Selects a disc menu language.*1  
(See <Language Setup>, page 54)  
DVD SETUP 1 screen  
3
Selects a subtitle language.*1  
(See <Language Setup>, page 54)  
Selects an audio language.*1  
(See <Language Setup>, page 54)  
5
6
7
Menu  
Menu LANG  
en  
Sub t i t l e LANG  
Audio  
2
4
Set  
Set  
Set  
Set Up  
en  
Aud i o LANG  
en  
Dynam i c R ange Con t r o l  
7
5
6
SRC  
1
Sets the dynamic range.*2  
(
Wide)  
7
Mi d n i g h t  
The dynamic range is reduced by changing from  
"Wide" to "Normal" and from "Normal" to "Midnight".  
You can easy to listen a small sound when the  
dynamic range is narrow.  
8
DVD S ETUP  
1
This is effective only when you are using a Dolby  
Digital software.  
Displays the DVD SETUP 2 screen.  
8
DVD SETUP  
If  
is not shown,  
to display it.  
touch  
or  
52 English  
Displaying the DVD SETUP2  
screen  
Sets an angle mark display. (  
On)  
9
p
Selects the screen display mode.*1 (  
"16:9": Displays wide pictures.  
16:9)  
"4:3 LB": Displays wide pictures in the Letter Box  
format (having black stripes at the top and  
bottom of screen).  
DVD SETUP 2 screen  
"4:3 PS": Displays wide pictures in the Pan & Scan  
format (showing pictures cut at the right  
and left ends).  
Menu  
Ang l e Mar k  
9
Sc r e e n Ra t i o  
Audio  
9
On  
O f f  
S e t  
Set Up  
Displays the Parental Lock screen.*1 (  
(See <Parental Level Setup>, page 55)  
OFF)  
q
10  
10  
4 : 3 LB  
SRC  
Pa l en t a l L ev e l  
Off  
11  
12  
Keep "AUTO" to use.  
w
e
Output  
AUTO  
Displays the DVD SETUP 1 screen.  
13  
DVD S ETUP  
2
*1 Disabled when a DVD is being played.  
*2 Disabled when the Zone function is On.  
English 53  
Setup Menu  
Language Code Table  
Language Setup  
Abbreviation  
Language  
Language  
Abbreviation  
aa  
ab  
af  
Afar  
Latvian, Lettish  
Malagasy  
Maori  
lv  
mg  
mi  
mk  
ml  
mn  
mo  
mr  
ms  
mt  
my  
na  
ne  
nl  
no  
oc  
om  
or  
pa  
pl  
Select a language you use for the speech and  
menus.  
Abkhazian  
Afrikaans  
Amharic  
Arabic  
am  
ar  
Macedonian  
Malayalam  
Mongolian  
Moldavian  
Marathi  
Malay  
1
Display the Language Setup screen  
as  
ay  
az  
ba  
be  
bg  
bh  
bi  
Assamese  
Aymara  
Azerbaijani  
Bashkir  
See <Displaying the DVD SETUP 1 screen> (see  
page 52) and select a language you wish to use.  
Byelorussian  
Bulgarian  
Bihari  
Maltese  
Burmese  
Nauru  
Audio LANG  
1
en  
d
Bislama  
Bengali, Bangla  
Tibetan  
Nepali  
a
h
o
v
b
i
c
j
e
l
f
m
t
g
n
u
bn  
bo  
br  
ca  
co  
cs  
cy  
da  
de  
dz  
el  
Dutch  
k
r
Norwegian  
Occitan  
(Afan) Oromo  
Oriya  
Breton  
p
w
q
x
s
z
Catalan  
O R I G N4  
Corsican  
Czech  
y
Punjabi  
3
5
2
C l e ar  
Cancel  
E n t e r  
Welsh  
Polish  
Danish  
Pashto, Pushto  
Portuguese  
Quechua  
Rhaeto-Romance  
Kirundi  
ps  
pt  
qu  
rm  
rn  
German  
Bhutani  
Greek  
Enters a language code.  
1
2
en  
eo  
es  
et  
eu  
fa  
English  
Cancels the language setup and returns to the  
DVD SETUP 1 screen.  
Esperanto  
Spanish  
Estonian  
Basque  
Persian  
Romanian  
Russian  
Kinyarwanda  
Sanskrit  
Sindhi  
ro  
ru  
Clears the language code.  
3
4
rw  
sa  
sd  
sg  
sh  
si  
Sets the original audio language.  
(It appears during audio language setup.)  
Sets the language and returns to the DVD SETUP  
1 screen.  
fi  
Finnish  
Sangho  
5
fj  
Fiji  
Serbo-Croatian  
Singhalese  
Slovak  
fo  
fr  
Faroese  
French  
(It appears after you have entered a language  
code.)  
sk  
sl  
fy  
Frisian  
Slovenian  
Samoan  
Shona  
ga  
gd  
gl  
Irish  
sm  
sn  
so  
sq  
sr  
ss  
st  
su  
sv  
sw  
ta  
te  
tg  
th  
ti  
tk  
tl  
tn  
to  
Scots Gaelic  
Galician  
Guarani  
Gujarati  
Hausa  
2
3
Enter a language code  
Somali  
gn  
gu  
ha  
hi  
Albanian  
Serbian  
See the Language Code Table shown at right to  
select the desired language.  
Siswati  
Hindi  
Sesotho  
Sundanese  
Swedish  
Swahili  
hr  
hu  
hy  
ia  
Croatian  
Hungarian  
Armenian  
Interlingua  
Interlingue  
Inupiak  
Set the language you use  
Tamil  
ie  
Telugu  
ik  
Tajik  
E n t e r  
in  
Indonesian  
Icelandic  
Italian  
Thai  
is  
Tigrinya  
Turkmen  
Tagalog  
Setswana  
Tongan  
it  
iw  
ja  
Hebrew  
Japanese  
Yiddish  
ji  
jw  
ka  
kk  
kl  
Javanese  
Georgian  
Kazakh  
Turkish  
tr  
ts  
tt  
Tsonga  
Tatar  
Greenlandic  
Cambodian  
Kannada  
Korean  
Twi  
tw  
uk  
ur  
uz  
vi  
vo  
wo  
xh  
yo  
zh  
zu  
km  
kn  
ko  
ks  
ku  
ky  
la  
Ukrainian  
Urdu  
Uzbek  
Kashmiri  
Kurdish  
Kirghiz  
Vietnamese  
Volapuk  
Wolof  
Latin  
Xhosa  
ln  
Lingala  
Yoruba  
lo  
Laotian  
Chinese  
Zulu  
lt  
Lithuanian  
54 English  
Parental Level Setup  
3
Display the Parental Level Setup screen  
Sets a parental level.  
E n t e r  
1
Display the Parental Level code number screen  
(P53  
)
P a r e n t a l L e v e l  
q
S e t  
Le v e l 5  
1
P a r e n t a l Pa s s  
* * * *  
1
1
2
5
8
0
1
4
7
3
6
9
2
Return  
4
Le v e l 5  
Enter  
Sets a parental level.  
1
2
2
5
3
C l e ar  
Cancel  
Returns to the DVD SETUP 2 screen.  
4
5
Set a parental level  
Enters a code number.  
1
Cancels the current setup and returns to the DVD  
SETUP 2 screen.  
Clears the code number.  
2
3
4
5
Displays the present parental lock level.  
Determines the code number and displays the  
Parental Level Setup screen.  
Enter the parental level setup  
2
Enter the code number  
Return  
0
9
• If a disc has a higher parental lock level, the  
audience needs to enter the code number.  
• The parental lock level varies depending on a  
loaded disc.  
• The number you enter first is set as your code  
number.  
• If a disc has no parental lock, any audience can  
play it back even when you have set the  
parental lock.  
• You can clear the password by pressing the  
Reset button.  
English 55  
Setup Menu  
System Setup  
You can set up the system parameters.  
Displaying the System Set Up  
1 screen  
Returns to the Control screen of the previous  
source.  
1
Sys t em S e t U p  
Calls the Sound Effects Menu. (see page 68)  
Calls the Setup Menu.  
2
3
4
5
System Set Up 1 screen  
Turns the key touch tone On or Off. (  
On)  
Allows scrolling of text display on the Source  
3
Control screen. ( Auto)  
"Auto": Scrolls the screen automatically.  
"Manual": Allows you to scroll the screen manually.  
Menu  
Beep  
Audio  
2
1
4
4
5
6
On  
O f f  
O f f  
Set Up  
Sc r o l l  
Manua l  
Remo t e Se n s o r  
SRC  
Selects a remote control signal. ( On)  
If you turn it "Off", your operation from the remote  
controller is rejected when you are in the TV mode.  
6
7
6
On  
1
Displays the System Set Up 2 screen.  
System Se t Up  
7
Sys t em S e t U p  
If  
is not shown,  
to display it.  
touch  
or  
56 English  
Displaying the System Set Up  
2 screen  
Sets a music CD playback. (  
1)  
8
"1" Automatically recognizes and plays back an  
:
MP3/WMA disc, a DVD or a music CD.  
"2" Forcibly plays back a disc as a music CD.  
:
Select "2" if you wish to play a music CD having  
a special format or if you cannot play a disc in  
the "1" position.  
System Set Up 2 screen  
• You cannot play an MP3/WMA/VCD disc in the "2"  
position. Also, you may not play some music CDs  
in the "2" position.  
Menu  
CD Read  
Audio  
8
9
1
Set Up  
Key ILLUMI  
Green  
• Your setup is disabled when the disc is being  
played.  
SRC  
Selects an illumination color of receiver keys.  
9
p
(
Green)  
"Green" Green  
:
10  
System Se t Up  
2
"Red"  
Red  
:
Displays the System Set Up 1 screen.  
English 57  
Setup Menu  
AV Interface  
You can set audio and visual (AV) interface parameters.  
Displaying the AV I/F 1 screen  
Returns to the Control screen of the previous  
1
source.  
AV I / F S e t Up  
Calls the Sound Effects Menu. (see page 68)  
Calls the Setup Menu.  
2
3
4
AV I/F 1 screen  
Selects a navigation system connection. (  
RGB)  
"RGB" Allows the Kenwood’s Navigation System  
:
3
to connect via its interface cable.  
"AV-IN": Allows a third-party navigation system to  
connect via the AV INPUT port.  
Menu  
NAV  
4
AV - I N Name  
2
1
Audio  
4
5
AV - I N  
Set Up  
5
V I DEO  
"OFF" Must be used if no navigation system is  
SRC  
:
AV - I N  
connected. (The navigation display is  
6
7
Nor ma l  
R-CAM View  
Nor ma l  
cancelled when the AV source is switched.)  
Sets a name to be displayed when you select a  
system that is connected via the AV INPUT port.  
5
6
8
AV I / F  
1
(
VIDEO)  
If you have set the navigation system connection to  
"AV-IN", the display is fixed to "NAV".  
Sets an image display of the system that is  
connected via the AV INPUT port. (  
"Normal": When the image source is switched, an  
image entered via the AV INPUT port is  
displayed.  
Normal)  
"AUTO": When an image signal is entered via the  
AV INPUT port, this image is displayed.  
Sets how the rear camera image is displayed.  
"Reverse": Displays with left and right reversed.  
"Normal": Displays as it is.  
7
8
"R-CAM View" can be set only when "AV-IN Name"  
is set to "R-CAM".  
Displays the AV I/F 2 screen.  
AV I / F S e t Up  
If  
is not shown,  
to display it.  
touch  
or  
58 English  
Displaying the AV I/F 2 screen  
Selects an AV source to be output at the AV  
9
p
OUTPUT port. (  
AV-IN)  
If you select DVD as a source when the optional  
accessory DSP unit is connected, no DVD sound is  
output to the AV output port.  
Selects speakers used for voice guidance of the  
AV I/F 2 screen  
navigation system. (  
F-Left)  
"F-Left" Uses the front left side speaker for voice  
:
Menu  
AV -OUT  
9
Audio  
guidance.  
9
AV - I N  
Set Up  
"F-Right": Uses the front right side speaker for voice  
guidance.  
N AV I n t e r r u p t i o n  
F - A l l  
NAV Guide Volume Level  
10  
SRC  
"F-All":  
Uses both front speakers for voice  
guidance.  
11  
12  
11  
19  
L i n e Mu t e  
12  
On  
O f f  
Adjusts the volume for voice guidance of the  
q
w
navigation system. (  
19)  
13  
AV I / F  
2
Mutes the volume during voice guidance of the  
navigation system. ( On)  
When turned "On", the volume level drops for voice  
guidance.  
Displays the AV I/F 1 screen.  
e
English 59  
Setup Menu  
User Interface  
You can set up user interface (IF) parameters.  
Displaying the User I/F 1  
screen  
Returns to the Control screen of the previous  
source.  
1
User I / F S e t Up  
Calls the Sound Effects Menu. (see page 68)  
Calls the Setup Menu.  
2
3
User I/F 1 screen  
Switches the wall paper.  
4
Displays the User I/F 2 screen.  
5
3
Menu  
Audio  
2
1
User I / F S e t Up  
If  
is not shown,  
to display it.  
Set Up  
Wall Paper  
4
4
touch  
or  
Wall  
SRC  
5
User I / F  
1
60 English  
Displaying the User I/F 2  
screen  
Sets an on-screen display of the navigation screen.  
6
7
8
9
(
Auto)  
If you set to "Auto", an information is displayed for 5  
seconds when updated.  
Sets an on-screen display of the video playback  
User I/F 2 screen  
screen. (  
Auto)  
If you set to "Auto", an information is displayed for 5  
seconds when updated.  
6
Menu  
On SCRN NAV  
On SCRN VIDEO  
On SCRN DVD  
On SCRN TV  
MANU  
MANU  
MANU  
MANU  
Audio  
Sets an on-screen display of the DVD playback  
7
Set Up  
screen. (  
MANU)  
SRC  
8
9
If you set to "Auto", an information is displayed for 5  
seconds when updated.  
Sets an on-screen display of the TV screen.  
(
Auto) (optional accessory) (with the optional  
10  
User I / F  
2
accessory TV tuner connected only)  
If you set to "Auto", an information is displayed for 5  
seconds when updated.  
Displays the User I/F 1 screen.  
p
English 61  
Setup Menu  
Touch Panel Adjust  
Clock  
You can adjust the touch panel operations.  
Adjusts the clock time  
1
Display the Touch Panel Adjust screen  
1
Display the Clock Screen  
Touch Adjust  
Touch Adjust  
Clock Adjust  
If  
is not shown, touch  
Clock Adjust  
If  
is not shown, touch  
or  
to display it.  
or  
to display it.  
3
5
6
3 Menu  
Menu  
Touch Ad j u s t  
4
PM 1 1 : 1 8  
4
Audio  
2
Audio  
2
S e t  
Set Up  
Set Up  
7
5
6
Res e t  
On  
SRC  
1
1
SRC  
8
8
SYNC  
O f f  
T ouch  
C lock  
Returns to the Control screen of the previous  
source.  
1
Returns to the Control screen of the previous  
source.  
1
Calls the Sound Effects Menu. (see page 68)  
Calls the Setup Menu.  
2
3
4
Calls the Sound Effects Menu. (see page 68)  
Calls the Setup Menu.  
Clock time display.  
2
3
4
5
6
7
Allows you to start touch panel adjustment.  
Adjusts hours.  
2
Start to adjust the touch panel  
Adjusts minutes.  
Sets "00" minute.  
Setup examples: 3:00~3:29  
3:00  
4:00  
S e t  
3:30~3:59  
Sets the clock time in synchronous with the time  
data sent from the RDS station. <Function of  
8
DDX7035> (  
On)  
Touch Ad j u s t  
When turned "On", the synchronous mode starts  
and the clock cannot be adjusted manually.  
2
1
Cancel  
Reset  
2
Adjust the clock time  
Cancels the adjustment and returns to the Touch  
Panel Adjust screen.  
Resets to the initial status.  
1
2
Security Code Setup  
3
Adjustment  
You can set a security code to protect your  
receiver system against theft.  
When the Security Code function is activated, it can't  
be released.  
Note, your Security Code is the 4 digit number  
entered in your "Car Audio Passport" in this package.  
Touch the center of left lower and right upper  
when requested.  
62 English  
1
Display the Security Code Setup screen  
Security Set Up  
4
5
Register your security code  
E n t e r  
Security Set Up  
If  
is not shown, touch  
Reenter the security code  
or  
to display it.  
Reenter the same security code as that you have  
entered in Step 3 for confirmation.  
3
4
Menu  
Sec u r i t y Code  
5
S e t  
O f f  
Audio  
2
5
S I  
Set Up  
On  
If you enter a different security code, the screen  
returns to Step 3 (for the first code entry).  
SRC  
1
6
Register the security code again  
Secur i t y  
E n t e r  
Returns to the Control screen of the previous  
source.  
1
Calls the Sound Effects Menu. (see page 68)  
Calls the Setup Menu.  
Allows you to start security code registration.  
Turns the SI function On or Off.  
If turned "On", the burglar alarm lamp flashes  
when the vehicle ignition is off.  
2
3
Your security code has been registered.  
If you press the Reset button or if you disconnect  
your Receiver from the battery after the code  
registration, you need to enter the registered  
security code. See below for details.  
4
5
If you have pressed the Reset button or if you  
have disconnected the Receiver from battery...  
If you have already completed the code  
registration, the S e t is not displayed.  
1
Enter the correct security code  
2
Start the security code registration  
0
9
S e t  
You must enter the same security code as that you  
have entered in Step 3 above.  
Pa ss Wor d  
1
* * * *1 s t  
2
1
4
7
3
6
9
2
Enter the security code  
5
8
E n t e r  
0
3
2
4
Clear  
Cancel  
Enter  
Now, you can use your Receiver.  
If you enter an incorrect security code, you  
cannot use your Receiver for a while.  
Enters a security code.  
Clears your entry.  
Cancels the registration and returns to the  
Security Code Setup screen.  
1
2
3
Incorrect entry count Receiver inoperable  
time  
1
Enters the security code.  
4
2
5 minutes  
1 hour  
24 hours  
3
Enter a security code  
3
4 or more  
0
9
Input a four-digit number.  
English 63  
Setup Menu  
TV Setup (with the optional accessory TV Tuner connected only)  
The TV signal receiving areas can be set.  
Displaying the TV1 Area Set Up  
screen  
Returns to the Control screen of the previous  
1
source.  
TV S e t U p  
Calls the Sound Effects Menu. (see page 68)  
Calls the Setup Menu.  
2
3
4
5
TV1 Area Set Up screen  
Sets the present TV1 receiving area.  
Displays the TV2 Area Set Up screen.  
3
Menu  
China  
Audio  
2
TV S e t U p  
If  
is not shown,  
to display it.  
Set Up  
touch  
or  
SRC  
1
4
1
2
3
4
5
6
TV1 Area Set  
5
Displaying the TV2 Area Set Up  
screen  
Sets the present TV2 receiving area.  
Displays the TV1 Area Set Up screen.  
6
7
TV2 Area Set Up screen  
Menu  
Audio  
China  
Set Up  
SRC  
6
1
2
3
4
5
6
7
TV2 Area Set  
64 English  
RDS Setup <Function of DDX7035>  
The related RDS parameters can be set.  
Displaying the RDS Set Up 1  
screen  
Returns to the Control screen of the previous  
source.  
1
RDS S e t U p  
Calls the Sound Effects Menu. (see page 68)  
Calls the Setup Menu.  
2
3
4
5
RDS Set Up1 screen  
Sets a news bulletin interrupt time.  
Turns the Alternative Frequency function On or Off.  
3
(
On)  
Menu  
News  
4
AF  
Audio  
2
1
4
Of f  
On  
Turns the Region Restriction function On or Off.  
6
Set Up  
5
(
On)  
O f f  
O f f  
O f f  
SRC  
Reg i onal  
Turns the Auto TP Seek function On or Off. (  
Displays the RDS Set Up 2 screen.  
On)  
7
8
6
7
On  
Au t o TP S e ek  
On  
8
RDS Se t Up  
1
RDS S e t U p  
If  
is not shown,  
to display it.  
touch  
or  
Displaying the RDS Set Up 2  
screen  
Selects a display language for the PTY function.  
Displays the RDS Set Up 1 screen.  
9
p
RDS Set Up2 screen  
Menu  
Language Se l e c t  
German  
Audio  
9
9
Set Up  
SRC  
10  
RDS Set Up 2  
English 65  
Setup Menu  
AMP Control (with the optional accessory LX Power AMP connected only)  
Sets the power amp connected via the LX bus.  
Displaying the AMP Control  
screen  
Calls the Setup Menu.  
1
2
3
Calls the Sound Effects Menu. (see page 68)  
AMP Ctrl  
Returns to the Control screen of the previous  
source.  
AMP Control screen  
Setup option and value display  
Select a setup option.  
Selects a set value.  
4
5
6
7
5
5
1
Menu  
Audio  
2
3
6
7
6
Set Up  
Enters the set value.  
SRC  
AMP Ctrl  
• If  
is not shown,  
to display it.  
touch  
or  
4
A M P 1 VO LT 1 4 . 4 V  
A M P C o n t r o l  
S e t  
• For the model name of amp you can control from  
the system, see the amp’s catalog.  
• For the options and values you can change and  
for the amp’s operation when changed, see the  
amp’s instruction manual.  
66 English  
English 67  
Sound Effects Menu  
Sound Effects Menu  
You can set up the receiver sound effects.  
Displaying the Control screen  
Control screen  
DVD V I DEO  
1 3 : 5 0  
Audio  
Set Up  
Direct  
SRC  
IN  
SCRL  
T0:05:20  
TIME  
REP  
Chap  
KENWOOD  
Title  
1
3
You can display the same Sound Effects Menu on  
the Control screen of any source.  
T-REP  
Displaying the Sound Effects  
Menu screen  
Calls the Sound Effects Menu.  
1
2
3
Calls the Setup Menu. (see page 43)  
Audio  
Returns to the Control screen of the previous  
source.  
Sound Effects screen  
• Your setup on the <Sound Effects Menu> is  
adjusted automatically according to your <Audio  
Set Up> (see page 46) on the Setup menu. We  
recommend you to complete the <Audio Set Up>  
first, then set up the <Sound Effects Menu>.  
1
Aud i o Co n t r o l  
Equa l i z e r  
Aud i o  
Audio  
Set Up  
SRC  
2
3
Zone Con t r o l  
• Displayed items vary depending on the optional  
accessory connected.  
68 English  
Audio Control  
You can adjust the front and rear and right and left audio balance.  
Displaying the Audio Control  
1 screen  
Returns to the Control screen of the previous  
1
source.  
Aud i o Co n t r o l  
Calls the Setup Menu. (see page 43)  
Calls the Sound Effects Menu.  
Adjusts the right and left volume balance.  
Adjusts the front and rear volume balance.  
2
3
4
5
6
Audio Control 1 screen  
F r o n t  
5
F
FAD F12  
BAL R1 2  
3
Menu  
Adjusts the volume of the present source based on  
the difference level of original volume.  
Audio  
4
4
Set Up  
2
1
L
R
7
If you have increased the volume first, then  
reduced it using the "Vol. Offset", the big sound  
may suddenly be generated when you switch to  
another source.  
SRC  
SUB -15  
R
R e a r  
5
7
Vo l . O f f s e t  
- 1 5  
LOUD  
O f f  
6
6
8
Adjusts the subwoofer volume.  
7
8
Aud i o Con t ro l 1  
9
Turns the Loudness control function On or Off.  
(Does not appear when the optional accessory DSP  
unit is connected.)  
If turned "On", high and low tones are automatically  
enhanced during low volume. (  
On)  
Displays the Audio Control 2 screen.  
9
Displaying the Audio Control  
2 screen  
Adjusts the bass boost of the B.M.S power  
amplifier (optional accessory).  
p
You may not set some models of power amp boost  
to "+18". See the catalog or instruction manual of  
power amplifier.  
Audio Control 2 screen  
Set the center frequency of bass boost you have set  
for the "AMP Bass".  
If you set it to "Low", the center frequency is  
dropped for 20 to 30%.  
q
w
Menu  
Audio  
BMS AMP Bass  
F l a t  
BMS AMP FREQ  
10  
11  
10  
Set Up  
SRC  
Displays the Audio Control 1 screen.  
Normal  
Low  
11  
12  
Aud i o Con t ro l 2  
English 69  
Sound Effects Menu  
Equalizer  
You can set up the equalizer.  
Displaying the Equalizer  
screen  
Returns to the Control screen of the previous  
source.  
1
Equa l i z e r  
Calls the Setup Menu. (see page 43)  
Calls the Sound Effects Menu.  
2
3
4
Equalizer screen  
Select the adjustment items for the Tone Curve  
setup. (Does not appear when the optional  
accessory DSP unit is connected.)  
If you set it to "Off", only "Level" can be set up for  
Tone Curve.  
3
5
Tone  
Menu  
System  
Audio  
Set Up  
2
1
Q
N a t u r a l  
6
6
SRC  
Tone  
:
Displays the Tone curve setup  
screen. (see page 71)  
5
4
Syst em Q -Ex  
O f f  
P-EQ  
: Displays the Parametric Equalizer  
screen. (see <Parametric Equalizer>  
page 72) (with the optional accessory  
DSP unit connected)  
Equa l i zer  
You can adjust the value set for the  
Equalizer Curve Type.  
Selects an equalizer curve type.  
6
You can select any of the following equalizer curves.  
System Q  
"Natural"  
"Rock"  
"Pops  
"Easy"  
"Top 40"  
"Jazz"  
"User" (when the tone curve (page 71) is set up)  
KBS (with the optional accessory DSP unit connected)  
"Natural"  
"Top 40"  
"Rock"  
"Dance"  
"Vocal"  
"Classic"  
"User" (when Parametric Equalizer (page 72) is  
set up)  
70 English  
Tone curve setup  
Set a Q factor  
Q Factor  
5
6
You can set a Tone curve.  
Display the Tone setup screen  
1
You can set it up only when Bass or Middle is  
adjusted.  
Tone  
Close the Tone setup screen  
Tone setup screen  
Tone  
FREQ  
1
Bass  
Return  
80  
- 5  
Le v e l  
F a c t o r  
2
3
Midd l e  
T r e b l e  
Q
1 . 0  
4
O f f  
Bass DC EXT  
5
Re t u r n  
Bass adjustment items are displayed.  
Middle adjustment items are displayed.  
Treble adjustment items are displayed.  
Bass DC Extend settings  
1
2
3
4
If turned "On", it extends the bass center  
frequency to the low register by approximately  
20%.  
Returns to the Equalizer screen.  
5
Tone curve can be set for each source.  
Select a frequency band you wish to adjust  
2
Bass  
Midd l e  
T r e b l e  
You can adjust the following frequency bands.  
Bass: 60, 70, 80, 100/150 (When "Q Factor" is  
"2.00") Hz  
Middle: 500, 1k, 1.5k, 2k Hz  
Treble: 10k, 12.5k, 15k, 17.5k Hz  
Set a center frequency  
3
4
FREQ  
Set a level  
Level  
English 71  
Sound Effects Menu  
Parametric Equalizer  
5
Set a Q value  
You can Manually set the equalizer curve by  
adjusting the center frequency, gain and Q  
value. (with the optional accessory DSP unit  
connected)  
Q
Store or call the equalizer curve into/from  
memory  
1
Display the Parametric Equalizer screen  
To store the equalizer curve in memory:  
P-EQ  
P1  
P3  
P aramet r i c Equ a l i z e r  
2
Continue to touch  
2 seconds.  
P1  
to  
P3  
more than  
3
4
Band3 Band4  
1Band1 Band2  
Hz  
800  
Hz  
800  
KH z  
2 . 2 5  
KH z  
2 . 2 5  
FREQ  
G a i n  
5
6
7
5
6
7
dB  
+12  
dB  
+12  
dB  
+12  
dB  
+12  
To call the equalizer curve from memory:  
Q
3. 0 0  
3. 0 0  
3. 0 0  
3. 0 0  
8
9
P1  
P3  
Re t u r n  
P1  
P2  
P3  
Touch  
P1  
to  
P3  
of the equalizer curve  
Select a band to be adjusted.  
1234  
you wish to call from memory.  
Sets a frequency.  
5
6
7
8
When you call an equalizer curve, its type is shown  
as "User".  
Sets a gain level.  
Sets a Q value.  
Store the present equalizer curve in memory, or  
calls it from memory.  
6
Close the Parametric Equalizer screen  
Exits the Parametric Equalizer setup and returns  
to the Equalizer screen.  
9
Return  
2
Select a frequency band you wish to adjust  
Band1  
Band4  
You can adjust the following frequency bands.  
60, 80, 100, 120, 160, 200, 250 Hz  
315, 400, 500, 630, 800, 1k Hz  
1.25k, 1.6k, 2k, 2.5k, 3.15k, 4k Hz  
5k, 6.3k, 8k, 10k, 12.5k, 16k Hz  
1
2
3
4
3
4
Set a center frequency  
FREQ  
Set a gain  
Gain  
72 English  
English 73  
Sound Effects Menu  
Zone Control  
You can set the front and rear audio source.  
Displaying the Zone Control  
screen  
Returns to the Control screen of the previous  
source.  
1
Calls the Setup Menu. (see page 43)  
Calls the Sound Effects Menu.  
2
3
4
Zone Con t r o l  
Turns the Zone Function (that sets different source  
sounds for front and rear speakers) On or Off.  
Zone Control screen (when the Zone function is On)  
When turned On,  
and  
are shown.  
F
R
3
4
6
Menu  
Dua l  
Zone  
Zone  
Sets the front and rear audio source separately.  
(This button appears when the Zone function is On.)  
5
Audio  
Set Up  
2
1
Area  
R e v e r s e  
When the rear speaker sound is switched, the  
audio source that is output at the AV OUTPUT  
terminal is also switched to the same source.  
However, if you have set the "Area" to "Reverse",  
the audio source that is output at the AV OUTPUT  
terminal is switched depending on the front sound  
source.  
SRC  
F r o n t  
F
Rear  
R
5
TUNER  
5
DVD  
Zone Con t r o l  
Switches the front and rear audio sources.  
(This button appears when the Zone function is On.)  
Use "Reverse" to change over the front and rear  
audio sources.  
6
F
R
If the zone function is turned on, the  
/
button appears on each source control screen, with  
which you can adjust the volume balance between  
the front and rear sources.  
DVD V I DEO  
1 3 : 5 0  
Audio  
Set Up  
Direct  
SRC  
F
R
SCRL  
TIME  
PBC REP  
Title  
KENWOOD  
T-REP  
1
Chap  
3
T0:05:20  
74 English  
Digital Effect (with the optional accessory DSP unit connected only)  
You can set up the Digital Effect.  
Displaying the Digital Effect  
screen  
Returns to the Control screen of the previous  
1
source.  
Digital Effect  
Calls the Setup Menu. (see page 43)  
Calls the Sound Effects Menu.  
2
3
4
Digital Effect screen  
PCM Center  
If you set to "On", a sound is output from the center  
speaker.  
8
De f e a t  
O f f  
3
Menu  
PCM C e n t e r  
4
D o l b y P r o Logi c  
Audio  
4
5
6
7
On  
Turns the Dolby Pro Logic function on or off.  
5
6
Set Up  
2
1
5
B i Phant om  
On  
O f f  
O f f  
O f f  
Turns the Bi Phantom function on or off.  
If you set to "On", the signal of the center channel is  
controlled so that it can be exactly positioned.  
SRC  
6
On  
Dynam i c R a n g e  
7
On  
Sets up the dynamic range when the Dolby Digital  
sound is used.  
If you set to "On", it compresses the dynamic range  
to control loud sounds.  
7
8
D i g i t a l E f f e c t  
The DSP unit settings return to default.  
• The Dolby Pro Logic and PCM Center functions  
are effective when the 2ch PCM signal is used.  
• You cannot set up "Bi Phantom" when "Dolby Pro  
Logic" is "Off".  
• You cannot set up "PCM Center" when "Dolby Pro  
Logic" is "On".  
English 75  
Sound Effects Menu  
Position (with the optional accessory DSP unit connected only)  
You can adjust the sound effects according to your listening position.  
Displaying the Position screen  
Returns to the Control screen of the previous  
source.  
1
Calls the Setup Menu. (see page 43)  
Calls the Sound Effects Menu.  
2
3
4
Position  
Sets a listening position.  
Position screen  
You can select any of "Front R" (Right front), "Front  
L" (Left front), "Front" (All front), "Rear" (All rear), and  
"ALL" (All) positions.  
3
Menu  
Audio  
Set Up  
2
1
The final distance is adjusted to the total of Car  
Type Set Up value (see page 46) and Position  
Setup (both Position and Position Fine Control)  
value.  
SRC  
Pos i t i on  
4
4
F r o n t  
Pos i t i on  
76 English  
English 77  
Hands-Free Unit Control  
GSM control  
You can call the following control screens if the GSM is connected to the system.  
Displaying the Control screen  
Displays the Search for Phone Book screen.  
(See the <Calling by Phone Book>, page 80)  
1
2
3
Or the telephone  
is called.  
Adds a number to the Phone Book.  
(See the <Addition to Phone Book>, page 81)  
Displays the Create a Mail screen.  
(See the <Creating an SMS (Short Message  
Service) messages>, page 84)  
GSM Control screen  
13  
14  
15  
AUTO  
FULL  
Hands Free  
6
16KENWOOD  
0123456789  
9
1
2
Displays the SMS list.  
(See the <Reading SMS (Short Message Service)  
messages>, page 84)  
4
P1  
P2  
P3  
7
10  
11  
8
1
4
7
*
2
5
8
0
3
6
9
#
+
3
4
5
Displays the Hands-Free Call Setup screen.  
(See the <Hands Free Setup>, page 83)  
5
6
7
8
Clear  
+
Enter three phone numbers for quick dialing.  
(See the <Quick Dialing>, page 83)  
12  
Return  
Set Up  
Enters a phone number.  
(See the <When dialing>, page 79)  
Clears the entered phone number.  
All numbers you have entered are cleared if the  
button is pressed more than 1 second.  
Starts the hands-free phone call.  
9
p
q
w
e
r
Displays the previously called phone number.  
Ends the hands-free phone call.  
Returns to the previous screen.  
Displays the radio wave intensity  
Displays the present Auto Response status  
AUTO  
When Auto Response is on:  
When Auto Response is off:  
Indicates the SMS registration availability  
t
y
Displays the calling and called phone numbers  
If you have registered a phone number in the Phone  
Book, the destination person name is displayed.  
For details on the hands-free phone calls, see the  
Instruction Manual of KCA-HF521 GSM Hands-Free  
Unit (optional).  
78 English  
When called  
When dialing  
When you are called, you can use the hands-  
free phone.  
Originate a call by entering a phone number.  
1
Enter a phone number  
1
Respond to a phone call  
9
0
2
Originate a call  
When the telephone is called, the GSM Control  
screen appears automatically.  
2
Terminate the phone call  
You can start talking when the destination responds.  
3
Terminate the phone call  
The previous screen reappears.  
The previous screen reappears.  
English 79  
Hands-Free Unit Control  
Phone Book List screen  
Calling by Phone Book  
AUTO  
FULL  
Phone Book L i s t  
0123456789  
KENWOOD  
You can call a person using his/her phone  
number that you have registered in the Phone  
Book.  
3 E d i t  
4 Clear  
2
Name  
1
Name  
1
Display the Search for Phone Book screen  
5
1
Ok  
Name  
6
Return  
Name  
Scrolls the list.  
1
2
3
The Initial Input screen appears.  
Enters the destination (called party) name.  
Displays the destination data edit screen.  
(See the <Editing the Phone Book>, page 82)  
Clears the destination if this button is touched  
more than 2 seconds.  
Enters the destination data and returns to the  
GSM Control screen.  
Returns to the GSM Control screen.  
Initial Input screen  
4
5
6
AUTO  
FULL  
Phone Book L i s t  
3
a
h
o
v
Aa  
Type  
b
i
c
j
d
k
r
e
l
f
m
t
g
n
u
1
2
2
p
w
q
x
s
z
3
4
Select a destination you wish to call  
y
4
Return  
Name  
Switches the character type.  
1
2
3
Scrolls the character array display.  
Displays the Phone Book beginning with the  
Select a destination you wish to call  
name whose first character you have touched.  
Returns to the GSM Control screen.  
4
Ok  
Select the initial character of a person name  
in memory  
2
The GSM Control screen appears again. The selected  
destination data is displayed.  
etc.  
a
5
6
Originate a call  
The Phone Book List screen appears.  
You can start talking when the destination responds.  
Terminate the phone call  
The previous screen reappears.  
80 English  
Select a memory device in which you wish  
to register phone data  
Addition to Phone Book  
3
You can add a phone number to the Phone  
Book.  
SIM CARD  
IN MEMORY  
1
Enter a phone number you wish to register  
When you select the device, the Name Edit screen  
appears.  
9
0
Name Edit Screen  
2
Start phone number registration  
AUTO  
4
FULL  
1Name Ed i t  
Kenwood  
1
a
h
o
v
Aa  
Type  
b
i
c
j
d
k
r
e
l
f
m
t
g
n
u
+
2
5
Clear  
3
p
w
q
x
s
z
6
7
Ok  
Device Select screen  
y
8
3
Space  
Return  
AUTO  
FULL  
D e v i c e S e l e c t  
1
SIM CARD  
Shifts the cursor.  
1
2
2
IN MEMORY  
Switches the character type.  
The digits, accent and extended code characters,  
and alphabets are switched each time it is  
pressed.  
3
Return  
Scrolls the keyboard display.  
3
4
5
Enters a character.  
Clears the character.  
Registers a phone number in the SIM card.  
1
2
All entry characters are cleared if this key is  
touched more than 1 second.  
Enters the entry characters.  
Registers a phone number in the GSM system  
itself.  
Returns to the GSM Control screen.  
6
7
8
3
Returns to the Device Select screen.  
Enters a space.  
The extended code characters are displayed only  
when a cellular phone supporting the GSM  
alphabets is connected.  
Each of extended code characters (^, {, }, \, [, ], ¯,  
|, ) occupies a two-character memory space  
when registered.  
4
5
Enter a name  
etc.  
a
Register the name  
Ok  
The name has been registered.  
English 81  
Hands-Free Unit Control  
Editing the Phone Book  
4
Register the phone number  
You can edit data you have registered in the  
Phone Book.  
Ok  
1
Select an item you wish to edit  
The phone number is registered, the Edit Name  
("Name Edit") screen appears.  
Name  
Edit Name ("Name Edit") screen  
AUTO  
FULL  
1
See the <Calling by Phone Book> (see page 80) and  
select an item you wish to edit on the Phone Book  
List screen.  
1Name Ed i t  
Kenwood  
4
a
h
o
v
Aa  
Type  
b
i
c
j
d
k
r
e
l
f
m
t
g
n
u
2
Clear5  
AUTO  
FULL  
Phone Book L i s t  
0123456789  
KENWOOD  
3
p
w
q
x
s
z
6
Ok  
y
7
8
3
Space  
Return  
Name  
Name  
Name  
Name  
E d i t  
Clear  
Ok  
Shifts the cursor.  
1
2
Switches the character type.  
Return  
The digits, accent and extended code characters,  
and alphabets are switched each time it is  
pressed.  
2
Start editing  
Scrolls the keyboard display.  
3
4
5
Enters a character.  
Clears the character.  
E d i t  
All entry characters are cleared if this key is  
touched more than 1 second.  
Enters the entry characters.  
6
7
The Edit Phone Number screen appears.  
Returns to the Edit Phone Number ("TEL Number  
Edit") screen.  
Enters a space.  
Edit Phone Number ("TEL Number Edit") screen  
8
AUTO  
FULL  
Number Ed i t  
The extended code characters are displayed only  
when a cellular phone supporting the GSM  
alphabets is connected.  
Each of extended code characters (^, {, }, \, [, ], ¯,  
|, ) occupies a two-character memory space  
when registered.  
0123456789  
1
1
4
7
*
2
5
8
0
3
6
9
#
2Clear  
4
Ok  
+
3
Return  
5
6
Enter a name  
Enters a phone number.  
1
2
etc.  
a
Clears the input phone number.  
All entry number are cleared if this key is touched  
more than 1 second.  
Register the phone number  
Returns to the Phone Book List screen.  
3
4
Enters the phone number.  
Ok  
3
Enter a phone number  
The editing completes and the Phone Book data is  
updated.  
9
0
82 English  
Quick Dialing  
Hand Free Setup  
You can register up to 3 phone numbers for  
quick dialing.  
The hands-free system can be set as follows.  
Display the SMS SetUp screen  
To register a phone number:  
1
2
Display a phone number you wish to register  
Set Up  
See the <Calling by Phone Book> (see page 80) and  
<When dialing> (see page 79).  
Hands Free Set Up screen  
AUTO  
FULL  
Hands Free Set Up  
Register the phone number  
Au t o Response Time  
1
1
2
30 sec  
MIC s e nce  
31  
2
3
Phone Vo i c e  
3
P1  
P3  
Right  
L e f t  
4
5
Book SYNC  
SMS SYNC  
Continue to touch more than 2 seconds.  
6
Return  
To call a phone number from memory:  
Sets an automatic response time after call  
termination.  
1
P1  
P3  
Adjusts the microphone sensitivity.  
Sets a ringing tone output position.  
2
3
"Left": Outputs the tone from the front left-hand  
side speaker.  
Only a phone number can be registered for  
Quick Dialing. Therefore, the destination  
subscriber name and others are not displayed  
during dialing.  
"Right": Outputs the tone from the front right-hand  
side speaker.  
Synchronizes the GSM with the Phone Book of  
optional KCA-HF521 unit.  
Synchronizes the GSM with the SMS of optional  
KCA-HF521 unit.  
4
5
6
Returns to the GSM Control screen.  
The "Phone Voice" of both "Left" and "Right" can  
be turned On at the same time. But they cannot  
be turned Off at the same time.  
English 83  
Hands-Free Unit Control  
Reading the SMS (Short  
Message Service) messages  
Creating an SMS (Short  
Message Service) message  
You can display messages received by the  
SMS.  
You can create a message to be sent by the  
SMS.  
Enter the destination number where you  
wish to send an SMS message  
1
Display the BOX Message List screen  
1
9
0
BOX Message List screen  
2
Display the SMS Message Input screen  
1
AUTO  
FULL  
Box L i s t  
0 1234567890123456  
0 1234567890123456  
0 1234567890123456  
0 1234567890123456  
2
SMS Message Input screen  
AUTO  
FULL  
3
Message I n p u t  
Kenwood  
2
Return  
1
1
5
a
h
o
v
Aa  
Type  
b
i
c
j
d
k
r
e
l
f
m
t
g
n
u
7
Displays messages.  
1
2
3
2
Scrolls the message list.  
Returns to the GSM Control screen.  
4
p
w
q
x
s
z
Clear6  
y
3
8
4
Space  
Return  
2
Select a message you wish to display  
Shifts the cursor.  
1
2
Switches the character type.  
The digits, accent and extended code characters,  
and alphabets are switched each time it is  
pressed.  
The message is displayed on the Box Message  
screen.  
Enters a space.  
3
4
5
6
Scrolls the keyboard display.  
Enters a character.  
BOX Message screen  
AUTO  
FULL  
Clears the character.  
Box Message  
31 / 0 1 /02 2 0 :15  
All entry characters are cleared if this key is  
touched more than 1 second.  
Sends the created message.  
7
8
Returns to the GSM Control screen.  
1
2
Clear  
Return  
3
Create a message  
3
1
etc.  
a
Scrolls for a single message.  
1
Clears the message if this button is touched more  
than 2 seconds.  
2
Returns to the BOX Message List screen.  
3
84 English  
4
Send the message  
Returns to the GSM Control screen.  
The extended code characters are displayed only  
when a cellular phone supporting the GSM  
alphabets is connected.  
Each of extended code characters (^, {, }, \, [, ], ¯,  
|, ) occupies a two-character memory space  
when registered.  
English 85  
Glossary  
DVD: Digital Versatile Disc  
Title number (DVD)  
A type of disc which contains recording of  
audio/video packaged media with high video and  
audio quality, such as a movie, featuring large  
recording capacity and digital signal processing  
capability.  
The title is the largest unit of video and audio  
recorded in a DVD. It usually corresponds to a  
single movie of video software or an album  
(sometimes a piece of music) of music software.  
The numbers assigned to individual titles are  
referred to as the title numbers.  
VCD: VIDEO CD  
Chapter number (DVD)  
A type of CD which contains the recording of  
moving images. It compresses image information  
by about 1/120 and audio information by about 1/6  
and accommodates up to 74 minutes of recording  
in a disc with the same diameter as ordinary  
music CD of 12 cm.  
The chapter is a section of video and audio  
recorded in a DVD. A title is composed of several  
chapters. The numbers assigned to individual  
chapters are referred to as the chapter numbers.  
Some VCDs do not have the P.B.C. compatibility  
and are capable of playback only, while some are  
P.B.C.-compatible and are capable of various  
special playback control operations. This player  
can play both of these VCDs.  
Subtitles (DVD)  
Some DVD discs contains the recording of more  
than one subtitle language. This player allow you  
to select one of the recorded subtitle languages  
during playback.  
MPEG: Moving Picture Expert Group (DVD, VCD)  
Track number (CD, VCD)  
This is an international standard for digital video  
and audio compression and decompression in  
media.  
A track is also a section of video and audio  
recorded in a disc. The numbers assigned to  
individual tracks are referred to as the track  
numbers.  
With most of music CDs, a track is assigned to a  
piece of music. However, with a VCD, the  
sections of the contents do not always  
correspond to the assigned tracks.  
As (special) playback functions such as skipping  
and programming of ordinary CDs are based on  
track number data, such playback functions are  
sometimes impossible with some VCDs.  
Dolby Digital  
This is a digital audio compression technology  
developed by Dolby Laboratories. It is compatible  
with 5.1-channel surround audio as well as normal  
stereo (2-channel) audio and can accommodate a  
large amount of audio data efficiently in a disc.  
DTS  
Name of a digital surround system developed by  
Digital Theater Systems, Inc.  
P.B.C.: Play-Back Control (VCD)  
When a VIDEO CD carries "Play Back Control  
capable" or similar message on the disc or jacket,  
desired scenes and information can be played  
back in an interactive manner using a hierarchical  
structure while viewing the menu screens  
displayed on the TV screen.  
Top menu/menu (DVD)  
Some DVDs display more than one title in a  
screen. This screen is referred to as the top  
menu.  
The menu is the item display (menu screen) for  
use in setting operations. The menu can be  
recalled any time during playback to perform  
settings according to the current software,  
including the audio switching between Dolby  
Digital and PCM, switching of language used in  
the subtitles and spoken voice.  
86 English  
Troubleshooting Guide  
Some system functions are limited to control depending on your setup.  
"Multi Channel" has been set to "2/0"  
or "3/0" (no rear speaker setting) on  
the Speaker Set Up screen (page 47).  
The rear speakers of DTA cannot be set.  
The "Channel Level" of rear speakers cannot be set.  
No signals can be set.  
The "Equalizer" cannot be set.  
The "Position" cannot be set.  
The Zone Control has been turned  
On (page 74).  
The "Car Type Setup" value cannot be set.  
The "Speaker Setup" value cannot be set.  
No crossover frequency can be set.  
The "Channel Level" (test signal output) cannot be set.  
"Multi Channel" has been set to "2/0"  
or "2/2" (no center speaker setting) on  
the Speaker Set Up screen (page 47).  
The center speaker for DTA cannot be set.  
The "Channel Level" of the center speaker cannot be set.  
The subwoofer of DTA cannot be set.  
"Sub Woofer" has been set to "Off" on  
the Speaker Set Up screen (page 47).  
The "Channel Level" of the subwoofer cannot be set.  
English 87  
Troubleshooting Guide  
What might appear to be a malfunction in your unit may just be the result of slight misoperation or  
miswiring. Before calling service, first check the following table for possible problems.  
General  
The power does not turn on.  
• After checking for short circuits in the wires, replace the  
fuse with one having the same rating.  
• The fuse has blown.  
The desired source is NOT selected although you pressed the SRC button.  
• A non-connected source is not selected. See  
<INSTALLATION MANUAL> and connect the unit correctly.  
• Press the reset button (see page 4).  
• An optional unit required to listen to each source is  
not connected yet.  
• The RESET button is not pressed yet although the  
optional unit has been connected to the system.  
• The "O-N" switch of the optional unit is at the "O"  
position.  
• Set the "O-N" switch to the "N" position.  
• Use a disc changer supported by the system (see page 4).  
• A disc changer not supported by the system is used.  
Nothing happens when the buttons are pressed.  
• Press the reset button on the unit (see page 4).  
• The computer chip in the unit is not functioning  
normally.  
No television/video image appears.  
• Make proper connections according to <INSTALLATION  
MANUAL>.  
• The unit is not connected to the parking brake  
detection switch.  
• For safety reasons no television/video images are  
displayed while the vehicle is moving. Engaging the  
parking brake will cause images to be displayed.  
• The parking brake is not engaged.  
The screen is dark.  
• If the temperature of the monitor unit drops, the screen  
may appear darker when power is first turned on due to  
the characteristics of a liquid crystal panel. Wait a while  
after turning power on for the temperature to rise. Normal  
brightness will return.  
• The unit is in a location where temperature is low.  
The screen does not darken when the vehicle’s lights are turned on.  
• When the unit is set to auto dimmer, it is not linked to the  
vehicle's light switch.  
• The unit is set to auto dimmer.  
• Make proper connections according to <INSTALLATION  
MANUAL>.  
• The illumination wire has not been connected. (If  
manual dimmer is set)  
AM/FM radio reception is poor and/or there is noise.  
• Separate the two antennas as far as possible.  
• Turn off the main unit.  
• The TV antenna and vehicle‘s radio antenna are too  
close.  
The remote controller does not operate.  
• Switch the remote control mode selector according to the  
source you select (see page 12).  
• The remote control mode selector is not set  
correctly.  
88 English  
No sound can be heard, or the volume is low.  
• Attenuator is turned on.  
• The fader or balance settings are set all the way to  
one side.  
• Turn off Attenuator.  
• Reset the fader and/or balance settings.  
• The input/output wires or wiring harness are  
connected incorrectly.  
• Reconnect the input/output wires or the wiring harness  
correctly. See the section on <INSTALLATION MANUAL>.  
The sound quality is poor or distorted.  
• One of the speaker wires is being pinched by a  
screw in the car.  
• Check the speaker wiring.  
• The speakers are not wired correctly.  
• Reconnect the speaker wires so that each output terminal  
is connected to a different speaker.  
Radio reception is poor.  
• The car antenna is not extended.  
• The antenna control wire is not connected.  
• Pull the antenna out all the way.  
• Connect the wire correctly, referring to the section on  
<INSTALLATION MANUAL>.  
The memory is erased when the ignition is turned off.  
• The battery wire has not been connected to the  
proper terminal.  
• The ignition and battery wire are incorrectly  
connected.  
• Connect the wire correctly, referring to the section on  
<INSTALLATION MANUAL>.  
• Connect the wire correctly, referring to the section on  
<INSTALLATION MANUAL>.  
The TEL mute function does not work.  
• The TEL mute wire is not connected properly.  
• Connect the wire correctly, referring to the section on  
<INSTALLATION MANUAL>.  
The TEL mute function turns on even though the TEL mute wire is not connected.  
• The TEL mute wire is touching a metal part of the  
car.  
• Pull the TEL mute wire away from the metal part of the  
car.  
The sound/picture skips on a DVD/VCD/CD.  
• The disc is scratched or dirty.  
• Clean the disc, referring to the section on <Disc cleaning>  
(see page 6).  
A track will not play.  
• Random play has been selected.  
• Turn off random play.  
A VCD cannot be played using menus.  
• The VCD disc being played is not compatible with  
P.B.C.  
• Menu playback is available only with VCD discs recorded  
with P.B.C.  
The subtitle is not displayed.  
• The DVD disc being played does not contain the  
recording of subtitles.  
• The subtitle cannot be displayed when the DVD disc being  
played does not contain the recording of subtitles.  
The voice (or subtitle) language cannot be changed.  
• The DVD disc being played does not contain the  
recording of more than one audio (or subtitle)  
language.  
• The voice (or subtitle) language cannot be changed when  
the DVD disc being played does not contain the recording  
of more than one voice (or subtitle) language.  
English 89  
Troubleshooting Guide  
The viewing angle cannot be changed.  
• The DVD disc being played does not contain the  
recording of more than one angle.  
• The viewing angle cannot be changed when the DVD disc  
being played does not contain the recording of more than  
one angle.  
• More than one viewing angle may be recorded only in  
limited sections in a disc.  
• You are attempting to switch the angle in a DVD  
section where more than one angle is not recorded.  
Playback will not start even after a title is selected.  
• A viewing restriction (RATING) has been set for the  
disc.  
• Check the viewing restriction level (RATING) setting.  
The voice or subtitle language selected in the initial setting is not played.  
• The DVD disc being played does not contain the  
recording of the selected voice or subtitle language.  
• Use a DVD disc containing the recording of the selected  
voice or subtitle language.  
Disc source  
The disc control mode cannot be selected.  
• No wire has been connected to the disc changer  
input terminal on the unit.  
• Connect the wire to the disc changer input terminal on the  
unit.  
The specified disc does not play, but another one plays instead.  
• The specified CD is quite dirty.  
• The CD is upside-down.  
• The disc is loaded in a different slot from that  
specified.  
• Clean the CD.  
• Load the CD with the labeled side up.  
• Eject the disc magazine and check the number for the  
specified disc.  
• The disc is severely scratched.  
• Try another disc instead.  
The sound skips.  
• Something is touching the disc changer.  
• The CD is scratched or dirty.  
• Remove whatever is touching it.  
• If skipping happens at the same place when the car is  
stopped, something with the CD is wrong. Clean the CD.  
The display shows that the changer is being played, but no sound can be heard.  
• The computer chip in the unit is not functioning  
normally.  
• Press the reset button on the unit (see page 4).  
The specified track will not play.  
• Random play or magazine random play has been  
selected.  
• Turn off random play or magazine random play.  
Track repeat, disc repeat, track scan, disc scan, random play, and magazine random play start by themselves.  
• The setting is not cancelled.  
• The settings for these functions remain on until the  
setting to off or the disc ejected, even if the power is  
turned off or the source changed.  
Can’t remove disc.  
• The cause is that more than 10 minutes has elapsed  
since the vehicle ACC switch was turned OFF.  
• The disc can only be removed within 10 minutes of the  
ACC switch being turned OFF. If more than 10 minutes  
has elapsed, turn the ACC switch ON again and press the  
Eject button.  
90 English  
MP3/WMA source  
Cannot play an MP3/WMA.  
• The media is scratched or dirty.  
• Clean the media, referring to the CD cleaning of the  
section on <About discs> (see page 6).  
The sound skips when an MP3/WMA is being played.  
• The media is scratched or dirty.  
• Clean the media, referring to the CD cleaning of the  
section on <About discs> (see page 6).  
• Record the media again or use another media.  
• The recording condition is bad.  
The MP3/WMA track time isn’t displayed correctly.  
• ---  
• There are times when it isn’t displayed correctly according  
to the MP3/WMA recording conditions.  
Can’t display the ID3 tag information correctly.  
• Record is not made in conformity with the ID3 tag  
version 1.x.  
• Record in conformity with the ID3 tag version 1.x.  
Also, the display may be incorrect if an MP3 file uses the  
ID3 tag v1.x standard and if this standard has been  
expanded after production of the machine software.  
The following messages are displayed when certain problems are occurring in your system. Take  
the recommended actions.  
Hot Error  
The protective circuit in the unit activates when the temperature inside the unit exceeds 60°C  
(140°F), stopping all operation.  
]
Cool down the unit by opening the windows or turning on the air conditioner. As the  
temperature falls below 60°C (140°F), the disc will start playing again.  
Hold Error  
Mecha Error  
The protective circuit in the unit activates when the temperature inside the automatic disc  
changer exceeds 60°C (140°F), stopping all operation.  
]
Cool down the unit by opening the windows or turning on the air conditioner. As the  
temperature falls below 60°C (140°F), the disc will start playing again.  
The disc player is malfunctioning.  
]
Eject the disc and try inserting it again. Contact the Kenwood dealer if this indicator continues  
blinking or the disc cannot be ejected.  
Disc Error  
Read Error  
The unplayable discs is inserted.  
The disc is upside-down.  
]
Load the disc with the labeled side up.  
The disc is quite dirty.  
]
Clean the disc, referring to the section on <Disc cleaning> (see page 6).  
Region code Error  
Parental level Error  
Error 07 — 67  
The DVD software encoded for other region code.  
The parental level is set to high levels.  
The unit is malfunctioning for some reason.  
]
Press the reset button on the unit. If the "Error ##" code does not disappear, consult your  
nearest service center.  
English 91  
Specifications  
Specifications subject to change without notice.  
Monitor section  
Video section  
Picture size................................................6.4 inches wide  
143.6(W)×77.1(H)mm  
Color system of external video input ................NTSC/PAL  
External video input level (RCA jacks) ..............1Vp-p/75  
External audio max input level(RCA jacks)............1V/22kΩ  
Analog RGB input ..........................................0.7Vp-p/75Ω  
Display system ........................Transparent TN LCD panel  
Drive system..............................TFT active matrix system  
Number of pixels....................336,960 (480H×234V×RGB)  
Effective pixels ......................................................99.99%  
Pixel arrangement......................RGB striped arrangement  
Back lighting ....................Cold Cathode Fluorescent Tube  
Audio section  
Maximum Power (Front&Rear) ..............................50W×4  
Full Bandwidth Power (Front&Rear)  
(at Less than 1%THD) ........................................22W×4  
Preout level (V) ....................................................2V/10kΩ  
Preout impedance ..................................................600Ω  
Tone action  
Bass........................................................100 Hz 10 dB  
Middle ......................................................1 kHz 10 dB  
Treble......................................................10 kHz 10 dB  
DVD section  
D/A Converter ............................................................24Bit  
Decoder ............Linear PCM/Dolby digital/dts/MP3/WMA  
Wow & Flutter ............................Below Measurable Limit  
Frequency response  
(Sampling frequency;96k) ........................20~44,000Hz  
(Sampling frequency;48k) ........................20~22,000Hz  
(Sampling frequency;44.1k) ......................20~20,000Hz  
Total harmonic distortion (1k) ................................0.010%  
Signal to Noise ratio................................100dB (DVD 96k)  
Dynamic range........................................100dB (DVD 96k)  
DISC Format........................DVD-Video/VIDEO-CD/CD-DA  
Sampling frequency........................44.1kHz/48kHz, 96kHz  
Quantifying bit number ....................................16/20/24bit  
General  
Operating voltage....................................14.4V (11V~16V)  
Current consumption ..................................................15A  
Dimensions (W×H×D) ..............182mm×112mm×163mm  
Operational temperature range ......................-10°C~60°C  
Storage temperature range ............................-20°C~85°C  
Weight: Main unit......................................................2.8kg  
FM Tuner section  
Frequency range (50kHz)..........................87.5~108.0MHz  
Usable sensitivity (S/N=26dB) ............9.3dBf (0.8µV/75)  
Quieting sensitivity (S/N=46dB) ........15.2dBf (1.6µV/75)  
Frequency response ( 3.0dB) ......................30Hz~15kHz  
S/N (dB) (MONO) ......................................................72dB  
Selectivity ( 400kHz) ........................................Over80dB  
Stereo separation............................................38dB (1kHz)  
AM Tuner section (DDX7045/7065)  
Frequency range (9kHz) ........................531kHz~1611kHz  
Usable sensitivity ....................................................28dBµ  
LW Tuner section (DDX7035)  
Frequency range (9kHz) ..........................153kHz~281kHz  
Usable sensitivity ....................................................28dBµ  
MW Tuner section (DDX7035)  
Frequency range (9kHz) ........................531kHz~1611kHz  
Usable sensitivity ....................................................28dBµ  
Although the effective pixels for the liquid crystal panel is given as 99.99% or more, 0.01% of pixels may not light or may  
light incorrectly.  
92 English  
is a trademark of DVD Format/Logo Licensing Corporation registered in the U.S., Japan and other countries.  
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual  
property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home  
and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is  
prohibited.  
Manufactured under license from Dolby Laboratories.  
"Dolby" and the double-D symbol are trademarks of Dolby Laboratories.  
"DTS" and "DTS 2.0 + Digital Out" are trademarks of Digital Theater Systems, Inc.  
English 93  

Radio Shack PLVWR900 User Manual
Philips 15PT2302 User Manual
Panasonic Palmcorder PV D300 User Manual
Olympus EVOLT E 500 User Manual
NEC Electronics America Car Video System LCD1970V User Manual
Laney Amplification Car Amplifier HCM30 User Manual
KitchenAid 4KFP720WH0 User Manual
Kenwood DDX8047 User Manual
Kenwood 68 User Manual
JVC GZ HM40 User Manual