Philips 15PT2302 User Manual

15PT2302  
Operating Instructions  
15PT2302/p1-4  
1
7/6/01, 10:48 AM  
SAFETY INFORMATION AND USEFULT IPS  
Safety Information  
Disconnect mains plug when :  
the red light below theTV screen is flashing continuously.  
a bright white line is displayed across the screen.  
cleaning theTV screen. Never use abrasive cleaning agents. Use a slight damp chamois  
leather or soft cloth.  
there is a lightning storm.  
the set is left unattended for a prolonged period of time.  
No naked flame sources, such as lighted candles, should be placed on top of theTV or  
in the vicinity.  
Do not place yourTV set under direct sunlight or heat.  
Leave at least 5 cm around each side ofTV set to allow for proper ventilation.  
Avoid placing your set (e.g. near the window) where it is likely to be exposed to rain  
or water.  
No objects filled with liquids should be placed on top theTV so as to avoid dripping  
or splashing of liquids on the set.  
UsefulTips  
Do not leave your set on standby mode for a prolonged period of time. Switch off set  
to allow it to be demagnetised. A demagnetised set supports good picture quality.  
Do not shift or move the set around when it is switched on. Uneveness in colour in  
some parts of the screen may occur.  
Never attempt to repair a defectiveTV yourself.Always consult a skilled service  
personnel.  
3
15PT2302/p1-4  
3
7/6/01, 10:48 AM  
BEFORE CALLING SERVICE  
Below is a list of frequently occurred symptoms. Before you call for service, make these simple  
checks. Some of these symptoms can easily be rectified if you know what to do.  
Symptom  
What you should do  
Colour patch  
(uneveness)  
• Switch off theTV by the mains power button.Wait for 20  
minutes before switching on again.  
• Check theTV is not placed too near speakers or magnetic  
objects.  
No power  
No picture  
• Check theTV’s AC power cord is plugged into the mains  
socket. If there is still no power, disconnect plug.Wait for  
60 seconds and re-insert plug. Switch on theTV again.  
• Check the antenna connection at the rear of theTV.  
• PossibleTV station problem.Try another channel.  
Good picture  
but no sound  
Try increasing the volume.  
• Check that the sound is not muted. If it is muted, press the  
Mute button on the remote control to restore sound.  
Good sound but poor  
colour or no picture  
Try increasing the contrast and brightness setting.  
• Check antenna connection at the rear of theTV.  
Snowish picture and  
noise  
Horizontal dotted lines  
• Possible electrical interference e.g. hairdryer, vacuum  
cleaner, etc. Switch off appliances.  
Double images or  
“Ghost” images  
• Possible poor positioning of antenna. Using a highly  
directional antenna may improve reception.  
TV not responding to  
remote control handset  
• Check life span of batteries of remote control handset.  
• Aim remote control handset directly at remote control  
sensor lens on theTV.  
4
15PT2302/p1-4  
4
7/6/01, 10:48 AM  
HOOKING UPY OUR TV (BASIC CONNECTION)  
Antenna Connection  
Connect the aerial plug to the antenna socket ¬  
on the backcover.  
75  
g
• Insert the mains plug into the wall socket.  
Mains Connection  
• For correct mains voltage, refer to type sticker at  
the rear of theTV set  
• Consult your dealer if mains supply is different.  
Note :This diagram is not representative of the  
actual plug and socket.  
Switching on the Set  
• Press the main power button to switch on/  
off theTV.  
• If the set is on standby (indicator is red),  
press the Power button on the remote  
control to switch on set.  
USE/CARE OF REMOTE CONTROL  
• Insert the correct type of batteries into the  
compartment.  
• Ensure the batteries are placed in the right  
direction.  
+
5
15PT2302/p5-10  
5
7/6/01, 3:17 PM  
CONNECTING THE AUDIO/VIDEO SOCKETS (PLAYBACK)  
Monitor  
out  
AV2  
in  
AV1  
in  
VIDEO  
AV sockets on  
rear of TV  
L
S-VIDEO  
AUDIO  
R
VCR (Equipped with  
Video andAudio  
Output sockets  
OUT  
ANTENNA  
IN  
OUT  
OUT  
Back of VCR  
VIDEO  
IN  
L
AUDIO  
IN  
R
You can view the playback ofVCR tapes (Video Disc players, camcorders, etc.) by using the AUDIO  
andVIDEO INPUT sockets on the rear of theTV.  
– Connect the VIDEO and AUDIO IN sockets on the rear of theTV to the AUDIO and  
VIDEO OUT sockets on theVCR.  
Monitor  
out  
AV1  
in  
AV2  
in  
VIDEO  
AV sockets on  
rear of TV  
L
S-VIDEO  
AUDIO  
R
Back of VCR  
OUT  
OUT  
OUT  
OUT  
ANTENNA  
IN  
L
AUDIO  
IN  
R
VIDEO  
IN  
S-VIDEO  
The S-Video connection on the rear of theTV is used for the playback of S-VHS VCR tapes,Video Discs,  
Video Games or Compact Disc-Interactive (cd-i) discs. Better picture detail and clarity is possible with  
the S-Video playback as compared to the picture from a normal antenna (RF) connection.  
– Connect the S-VIDEO socket on the rear of theTV to the S-VHS OUT socket on a  
S-VHS VCR.  
– Connect the AUDIO IN sockets from the rear of theTV to the AUDIO OUT sockets  
on theVCR. Note : You need not connect the VIDEO IN socket of theTV if S-VIDEO IN  
socket is connected.  
6
15PT2302/p5-10  
6
7/6/01, 11:36 AM  
CONNECTING THE AUDIO/VIDEO SOCKETS (RECORDING)  
Connection for recording from theTV channel  
AV1  
in  
AV2  
in  
Monitor  
out  
VIDEO  
AV sockets on  
rear of TV  
L
S-VIDEO  
AUDIO  
R
OUT  
ANTENNA  
IN  
OUT  
OUT  
VCR (Equipped  
withVideo and  
Audio Input  
sockets  
VIDEO  
IN  
L
R
AUDIO  
IN  
Back of VCR  
– Connect the corresponding INPUT sockets of the VCR to the MONITOR OUTPUT  
sockets on the rear of theTV.  
To enhance the sound of yourTV, connect the AUDIO L and R sockets to an external audio  
system instead of theVCR. For mono equipment, connect only the AUDIO L socket.  
Connection for recording from oneVCR to anotherVCR  
AV sockets on rear of TV  
AV1  
in  
AV2  
in  
Monitor  
out  
VIDEO  
L
S-VIDEO  
AUDIO  
R
OUT  
ANTENNA  
IN  
OUT  
OUT  
L
VIDEO  
IN  
R
AUDIO  
IN  
OUT  
ANTENNA  
IN  
OUT  
OUT  
Back of VCR  
VIDEO  
L
R
AUDIO  
IN  
IN  
VCR (Equipped  
withVideo and  
Audio Output  
sockets  
VCR (Equipped  
withVideo and  
Audio Input  
sockets  
– Connect the sockets of theVCR which you wish to record from, to the corresponding  
sockets at either AV1 orAV2  
– Connect the sockets of the receiving VCR to the MONITOR OUTPUT sockets on the  
rear of theTV.  
7
15PT2302/p5-10  
7
7/6/01, 11:37 AM  
FUNCTIONS OF REMOTE CONTROL  
& Power button  
Switch set off temporarily to standby mode.  
(The red light indicator lights up when the set  
is on standby mode).  
To switch on set from standby mode, press  
Channel +/– , Digit (0 -9) or Power button.  
&
é
(
§
è
!
ç
é Teletext Colour/Personal Zapping buttons  
In teletext mode, the colour buttons allow you to  
access directly an item or corresponding pages.  
As Personal Zapping buttons, you can surf up to  
10 personal channels for each button. For detailed  
description of functions, refer to section on  
Personal Zapping .  
Teletext buttons  
0
Allows you to access teletext information. For  
detailed description of functions, refer to section  
onUsing theTeletext”  
1
2
Smiley button  
Allows to add and store your personal preference  
channels in your Personal Preference list. For  
detailed description of functions, refer to section  
on Using your Personal Zapping feature.  
( Timer Button  
Allows you to set the clock to switch to another  
channel at a specified time while you are watching  
another channel or when the set is on standby mode.  
§ Smart Sound Button  
Press the Smart Sound button repeatedly to  
access 4 different types of sound settings and  
choose your desired setting.  
è Menu Button  
Displays the main menu.Also exits menu from screen.  
! Cursor Up Button  
Allows you to select the next item on the menu.  
ç Cursor Left Button  
Allows you to select the sub-menus and adjust the settings.  
0 Volume + / – Button  
Increases or decreases volume.  
1 4  
Allows you to switch from Stereo to Mono sound during  
stereo transmission or to choose between language5or  
language6during dual sound transmission.  
2 A/CH(Alternate channel) Button  
Allows you to change between the current  
channel and the previous channel.  
8
15PT2302/p5-10  
8
7/6/01, 11:37 AM  
FUNCTIONS OF REMOTE CONTROL  
3 Main Index Button  
In teletext mode, press button to return to the  
main index page.  
4 Frownie button  
Allows to delete stored personal preference  
channels in your Personal Preference list. For  
detailed description of functions, refer to section on  
Personal Zapping .  
3
4
5
5 Smart Picture Button  
Press the Smart Picture button repeatedly to  
access 5 different types of picture settings and  
choose your desired setting.  
6
7
61Incredible Surround Button  
8
9
Allows you to select Incredible Surround sound  
when transmission is in stereo mode.  
Allows you to select Spatial Sound when  
transmission is in mono mode.  
20  
21  
22  
71\Cursor Right Button  
Allows you to access the sub-menus and adjust  
the settings.  
8 Cursor Down Button  
Allows you to select the next item on the menu.  
9 Channel + / – Buttons  
23  
Allows you to select channels in ascending or  
descending order.  
20 Mute Button  
Mutes sound.To restore sound, press button again.  
21 Teletext Button  
24  
25  
Refer to section on “Using theTeletext”  
22 OSD button  
Allows you to display the current channel number.  
It also allows to exit menu from the screen after  
control adjustments.  
23 Digit (0 -9) Buttons  
Press to select a channel. For a 2-digit channel  
number, press the first digit and followed  
immediately by the second digit.  
24 A/V Button  
Allows you to select the AV channels.  
25 Sleeptimer Button  
Allows you to select a time period after which the  
setwill switch to standby mode automatically.  
9
15PT2302/p5-10  
9
7/6/01, 11:37 AM  
FUNCTIONS OF TV CONTROLS  
Push catch of lid  
upwards to open  
front controls cover  
INSTALL MENU  
3
;
¸ CHANNEL ˚  
VIDEO  
L
AUDIO  
R
VOLUME  
+
&
é “ ‘  
( §  
7
&
é
Mains Power button  
Standby light indicator  
Remote Sensor  
Switch mains power on or off.  
Indicate red light when standby mode is activated.  
Acts as a sensor for activating the controls of the  
TV when remote control handset is aimed at it.  
(
Headphone socket  
AV “in” sockets  
Connect headphone jack to socket for personal  
listening.  
Connect toVideo “out” and Audio “sockets”  
toVCR, VCD, etc. (For more details on  
connection, refer to section “Connecting the  
Audio/Video Sockets”).  
§
Volume – / + buttons  
Adjust sound volume softer/louder.  
Channel ¸/ ˚ buttons  
Select channel in ascending/descending order.  
7
Note  
You can enter the main menu by pressing both the Volume – and + buttons  
at the same time.  
Press the Channel ¸/ ˚ button to select the next item on the menu.  
Press Volume – / + button to access sub-menu and adjust the settings.  
10  
15PT2302/p5-10  
10  
7/6/01, 11:37 AM  
SELECTING THE MENU LANGUAGE  
Operating instructions generally explains the operation of theTV  
set using the buttons on the remote control unless otherwise stated.  
Please read the following instructions carefully and follow the steps  
as shown to familiarise yourself with the installations and all features  
available in your set.  
The Language feature allows you to set theTV’s on-screen menu to be shown in your  
desired language.  
Press button  
Step  
Result onTV Screen  
Enter main menu.  
Main  
Picture  
o
π
MENU  
Brightness  
Colour  
Contrast  
Sharpness  
Colour Temp.  
More...  
I
I
I
Sound  
Features  
Install  
œ
Select Install.  
¸
Main  
o
I
I
I
Picture  
Sound  
Features  
Language  
Auto Store  
Manual Store  
Sort  
Channel Edit  
Name  
Install  
π
œ
Install  
Language  
o
Enter the Install menu.  
˙
˙
English  
π
I
I
I
I
I
Auto Store  
Manual store  
Sort  
Channel Edit  
Press button repeatedly to cycle  
through the language list and  
select the language of your choice.  
Name  
œ
Exit menu from screen.  
m
AUTOMATIC TUNING  
11  
15PT2302/p11-19  
11  
7/6/01, 1:31 PM  
AUTOMATIC TUNING OF CHANNELS  
Automatic tuning of channels allows you to store each programme automatically.  
Press button  
Result onTV Screen  
Step  
Enter main menu.  
Main  
Picture  
o
π
MENU  
Brightness  
Colour  
Contrast  
Sharpness  
Colour Temp.  
More...  
I
I
I
Sound  
Features  
Install  
œ
o
Main  
Press button repeatedly until  
Install is selected.  
I
I
I
Picture  
Sound  
Features  
Language  
Auto Store  
Manual Store  
Sort  
Channel Edit  
Name  
¸
Install  
π
œ
Install  
Language  
o
Enter install menu.  
˙
π English  
I
I
I
I
I
Auto Store  
Manual store  
Sort  
Channel Edit  
Name  
œ
Install  
o
Select Auto Store.  
¸
I
Language  
Auto Store  
π
I
I
I
I
Manual store  
Sort  
Channel Edit  
Name  
œ
Auto Store  
I
Channel  
TV  
1
Start automatic tuning of  
channels.  
˙
I
142 MHz  
ooooooooooooooπoooooooooooooooo  
Install  
o
œ
I
Language  
Auto Store  
π
I
I
I
I
Manual store  
Sort  
Channel Edit  
Name  
When tuning is completed,  
exit menu from screen.  
m
12  
15PT2302/p11-19  
12  
7/6/01, 1:31 PM  
MANUAL TUNING OF CHANNELS  
Manual tuning of channels allows you to select your preferred channel number for every  
available programme.  
Step  
Press button  
Result onTV Screen  
Main  
Picture  
o
π
Enter main menu.  
MENU  
Brightness  
Colour  
I
I
I
Sound  
Features  
Install  
Contrast  
Sharpness  
Colour Temp.  
More...  
œ
o
Main  
Press button repeatedly until  
Install is selected.  
I
I
I
Picture  
Sound  
Features  
Language  
Auto Store  
Manual Store  
Sort  
Channel Edit  
Name  
¸
Install  
π
œ
Install  
o
Language  
π
English  
Enter install menu.  
I
I
I
I
I
Auto Store  
Manual Store  
Sort  
Channel Edit  
Name  
˙
œ
Install  
o
I
Language  
Auto Store  
Colour System  
Sound System  
I
Press button repeatedly until  
Manual Store is selected.  
Manual Store π Search  
¸
I
Sort  
Channel No.  
I
I
Channel Edit  
Name  
Fine Tune  
Store  
œ
Manual Store  
o
Enter manual store menu.  
˙
I
Colour System  
I
Sound System  
Search  
Channel No.  
Fine Tune  
Store  
79 MHz  
π
I
Press button repeatedly until  
Search is selected.  
I
I
¸
œ
MANUAL TUNING OF  
13  
15PT2302/p11-19  
13  
7/6/01, 1:31 PM  
MANUAL TCUNHIANNGNOELFSCHANNELS  
Press button Result onTV Screen  
Step  
Manual Store  
o
Start manual searching. Searching  
stops once a transmitting signal is  
found.  
I
Colour System  
Sound System  
Search  
˙
I
128 MHzπ  
I
Channel  
I
I
Fine Tune  
Store  
œ
Manual Store  
o
¸
Select Channel.  
I
I
I
Colour System  
Sound System  
Search  
Key in the channel number.  
2
5
8
0
1
4
7
3
6
9
Channel  
Fine Tune  
Store  
2
π
9
I
I
œ
Manual Storeo  
Press button repeatedly until  
Store is selected.  
10  
¸
I
I
I
I
I
Colour System  
Sound System  
Search  
Channel  
Fine Tune  
Store  
Store?π  
œ
Manual Storeo  
Store tuned channel.  
Note : If you want to  
continue searching for  
another transmitting  
channel, repeat steps  
7 to 11.  
11  
12  
I
I
I
I
I
Colour System  
Sound System  
Search  
Channel  
Fine Tune  
Store  
˙
m
Stored  
œ
Exit menu from screen.  
14  
15PT2302/p11-19  
14  
7/6/01, 1:31 PM  
SELECTING THE COLOUR/SOUND SYSTEM  
This feature allows you to select your desired Colour and Sound system. If Auto  
is selected, the respective colour and sound system will be automatically selected according  
to the transmission system. Note : Select your desired colour and sound system manually if  
reception is poor at Auto mode.  
Step  
Press button  
Result onTV Screen  
Repeat step 1  
to step 5 as in  
Colour System is selected.  
Manual Store  
o
Colour System  
Auto π  
“ManualTuning  
ofTV Channels”  
I
I
I
I
I
Sound System  
Search  
Channel  
Fine Tune  
Store  
œ
o
Manual Store  
Select the desired colour  
system (Auto, PAL,  
NTSC 3.58, NTSC 4.43  
or SECAM).  
˝
Colour System  
PAL  
π
I
I
I
I
I
Sound System  
Search  
Channel  
Fine Tune  
Store  
or  
˙
œ
o
Manual Store  
Press button repeatedly  
until STORE is selected.  
¸
I
I
I
I
I
Colour System  
Sound System  
Search  
Channel  
Fine Tune  
Store  
˙
Store selected system.  
Stored  
œ
o
Proceed to select Sound  
System.  
Manual Store  
¸
or  
˚
9
I
Colour System  
Sound System  
Search  
Auto  
π
I
I
I
I
Channel  
Fine Tune  
Store  
œ
o
Select the desired sound  
system (Auto, BG,I,  
DK or M.  
Manual Store  
˝
10  
I
Colour System  
Sound System  
Search  
or  
DK  
π
I
˙
I
I
I
Channel  
Fine Tune  
Store  
œ
o
Manual Store  
I
I
I
I
I
Colour System  
Sound System  
Search  
Channel  
Fine Tune  
Store  
11  
12  
13  
¸
˙
Press button repeatedly  
until STORE is selected.  
Stored  
Store selected system.  
Exit menu from screen.  
15  
œ
m
15PT2302/p11-19  
15  
7/6/01, 1:31 PM  
FINE TUNING OF CHANNELS  
This feature allows you to adjust picture reception in areas of weak reception.  
Press button  
Result onTV Screen  
Step  
Enter main menu.  
Main  
Picture  
o
π
MENU  
Brightness  
Color  
Contrast  
Sharpness  
Tint  
I
I
I
Sound  
Features  
Install  
More...  
œ
o
Main  
¸
Press button repeatedly until  
Install is selected.  
I
I
I
Picture  
Sound  
Features  
Language  
Auto Store  
Manual Store  
Sort  
Channel Edit  
Name  
Install  
π
œ
Install  
o
Enter install menu.  
I
Language  
Auto Store  
Manual Store  
Sort  
Channel Edit  
Name  
Colour System  
Sound System  
π Search  
Channel  
Fine Tune  
Store  
˙
I
I
Press button repeatedly until  
Manual Store is selected.  
¸
I
I
œ
Manual Storeo  
I
I
I
I
Colour System  
Sound System  
Search  
Enter manual store menu.  
˙
Channel  
Press button repeatedly until  
FineTune is selected.  
¸
Fine Tune  
Store  
p
❘❘❘❘❘❘❘❘❘❘❘ ❘❘❘❘❘❘❘❘❘❘❘π  
❘❘  
I
œ
Manual Storeo  
I
I
I
I
Colour System  
Sound System  
Search  
Fine tune until the best reception  
is obtained.  
˙
or  
Channel No.  
˝
Fine Tune  
Store  
p
❘❘❘❘❘❘❘❘❘❘❘❘❘❘❘❘❘❘ ❘❘❘❘π  
❘❘  
I
œ
¸
Manual Storeo  
Select Store.  
I
I
I
I
I
Colour System  
Sound System  
Search  
Channel No.  
Fine Tune  
Store  
Store last fine-tuned status.  
˙
9
Stored  
œ
10  
m
Exit menu from screen.  
16  
15PT2302/p11-19  
16  
7/6/01, 1:31 PM  
SORTING OF CHANNELS  
This feature rearranges channel numbers.  
Step  
Press button  
Result onTV Screen  
MENU  
Main  
o
Enter main menu.  
I
I
I
Picture  
Sound  
Features  
Language  
Auto Store  
Manual Store  
Sort  
Channel Edit  
Name  
Install  
π
¸
Press button repeatedly until  
Install is selected.  
œ
o
Install  
˙
Enter install menu.  
I
I
I
Language  
Auto Store  
Manual Store  
000  
001  
002  
003  
004  
005  
Press button repeatedly until  
Sort is selected.  
Sort  
Channel Edit  
π
¸
I
I
Name  
œ
Install  
o
Enter sort mode.  
˙
I
I
I
Language  
000  
001  
002  
003  
004  
005  
Auto Store  
Manual Store  
Sort  
Channel Edit  
Name  
π
Select the channel number you want  
to change from (e.g. 002).  
¸
or  
π
I
I
œ
o
˚
Install  
Confirm selection.  
I
I
I
Language  
000  
001  
002  
003  
004  
005  
˙
Auto Store  
Manual Store  
Sort  
Channel Edit  
Name  
p
π
œ
I
I
Install  
o
I
I
I
Language  
Auto Store  
Manual Store  
000  
¸
Select the channel number you want  
to change to (e.g. 005).  
001  
002  
003  
004  
005  
Sort  
π
I
Channel Edit  
Name  
I
p
œ
Confirm selection.  
The change is done.  
Note : Channel numbers 5, 4 and 3  
will move upwards accordingly. that  
is, Channel 5 will move up to Channel  
4, Channel 4 to 3 and Channel 3 to 2.  
˝
Install  
o
9
I
I
I
Language  
Auto Store  
Manual Store  
000  
001  
002  
003  
004  
005  
Sort  
Channel Edit  
Name  
π
I
I
π
œ
10  
Exit menu from screen.  
m
17  
15PT2302/p11-19  
17  
7/6/01, 1:31 PM  
EDITING OF CHANNELS  
This feature allows you to skip or edit channels which have bad or weakTV signal or channels  
that you do not watch often. Note : Once a channel is skipped, you cannot have access to it by  
theCH (Channel) + or – button.You can only have access to the channel by the Digit (0 -9)  
buttons.  
Step  
Press button  
Result onTV Screen  
Enter main menu.  
MENU  
Main  
o
I
I
I
Picture  
Sound  
Features  
Language  
Auto Store  
Manual Store  
Sort  
Channel Edit  
Name  
Press button repeatedly until  
Install is selected.  
Install  
π
œ
¸
Install  
o
˙
I
I
I
I
Language  
Auto Store  
Manual Store  
Sort  
Channel  
Skipped  
Enter install menu.  
¸
Press button repeatedly until  
Channel Edit is selected.  
Channel Editπ  
Name  
I
œ
Enter Channel Edit menu.  
˙
Channel Edit  
o
Channel  
Skipped  
2
π
I
2
5
8
0
1
4
7
3
6
9
Key in the channel number to be  
skipped.  
œ
o
Channel Edit  
I
Channel  
Skipped  
Select Skipped.  
¸
On  
Select On to skip channel.  
˙
œ
Exit menu from screen.  
9
m
HOW TO RESTORE SKIPPED CHANNELS  
• Repeat Steps 1 to 5 as in”Editing of Channels”.  
• Key in the channel number to be restored by the  
Digit (0 - 9) button.  
• Select Skipped by the Cursor Down button.  
• Select Off to restore channel by the Cursor Right button.  
• Exit menu from screen by the OSD button.  
Channel Edit  
o
œ
I
Channel  
Skipped  
Off  
18  
15PT2302/p11-19  
18  
7/6/01, 1:31 PM  
NAMING OF CHANNELS  
This feature enables you to name or rename channels.  
Step  
Press button  
Result onTV Screen  
Enter main menu.  
MENU  
Main  
o
I
I
I
Picture  
Sound  
Features  
Language  
Auto Store  
Manual Store  
Sort  
Channel Edit  
Name  
Press button repeatedly until  
Install is selected.  
¸
Install  
π
œ
Install  
o
Enter install menu.  
˙
I
I
I
I
I
Language  
000  
001  
002  
003  
004  
005  
Auto Store  
Manual Store  
Sort  
Press button repeatedly until  
Name is selected.  
¸
Channel Edit  
Name  
π
œ
Enter name mode.  
Install  
o
˙
I
I
I
I
I
Language  
Auto Store  
Manual Store  
Sort  
000  
001  
002  
003π  
004  
005  
Select the channel you want to  
name.  
˚
or  
¸
Channel Edit  
Name  
π
œ
Install  
o
Move to first character slot.  
I
I
I
I
I
Language  
Auto Store  
Manual Store  
Sort  
000  
001  
002  
003π  
004  
005  
˙
A cursor appears for you to start  
the input of characters. Select the  
character you want. Move to next  
character slot by the Cursor Right  
button and select the next character.  
You can enter up to a maximum of 5  
characters. After naming the channel,  
press Cursor Right button repeatedly  
until name appears on the top left  
hand corner of the screen.  
˚
or  
Channel Edit  
Name  
π
œ
¸
9
Exit menu from screen.  
m
19  
15PT2302/p11-19  
19  
7/6/01, 1:31 PM  
ADJUSTING THE TV PICTURE  
The picture menu allows you to make adjustments to the picture.  
Step  
Press button  
Result onTV Screen  
Display the main menu on screen.  
MENU  
Main  
o
Picture  
π Brightness  
Colour  
I
I
I
Sound  
Features  
Install  
Contrast  
Sharpness  
Colour Temp  
More...  
Picture  
Brightnessp❘❘❘❘❘❘❘❘❘❘❘ ❘❘❘❘❘❘❘❘❘❘❘59π  
o
Enter Picture menu.  
˙
I
I
I
I
I
Colour  
Contrast  
Sharpness  
Colour Temp  
NR  
Select item.  
˚
or  
¸
Picture  
Colour  
o
Adjust level or select desired  
setting.  
p❘❘❘❘❘❘❘❘❘❘❘ ❘❘❘❘❘❘❘❘❘❘❘59π  
˝
I
I
I
I
I
Contrast  
Sharpness  
Colour Temp  
NR  
or  
˙
Contrast +  
œ
Exit menu from screen.  
m
Picture menu items  
Brightness  
Activities  
Increase or decrease brightness level.  
Increase or decrease color level.  
Increase or decrease contrast level.  
Colour  
Contrast  
Sharpness  
Increase or decrease sharpness level to improve detail  
in picture.  
Color temperature  
Choose from 3 settings (Normal,Warm or Cool).  
NR (Noise Reduction)  
Select “On” to reduce “noisy” picture (little dots on  
picture) due to weak signal.  
Contrast +  
Select “On” to allow you to optimise the total contrast  
for improved picture quality.  
20  
15PT2302/p20-21  
20  
7/6/01, 1:35 PM  
ADUSTING THE TV SOUND  
The sound menu allows you to make adjustments to the sound.  
Step  
Press button  
Result onTV Screen  
Display the main menu on screen.  
Main  
Picture  
o
MENU  
π Brightness  
Colour  
I
I
I
Sound  
Features  
Install  
Contrast  
Sharpness  
Colour Temp.  
More...  
œ
Main  
Picture  
o
I
Treble  
π Bass  
Balance  
Select Sound menu.  
¸
Sound  
Features  
Install  
I
I
AVL  
Incr. Surround  
Ultra Bass  
Sound  
Treble  
o
Enter Sound menu.  
˙
p❘❘❘❘❘❘❘❘❘❘❘ ❘❘❘❘❘❘❘❘❘❘❘0π  
I
I
I
I
I
Bass  
Balance  
AVL  
Incr. Surround  
Ultra Bass  
œ
Select item.  
˚
or  
¸
Adjust level or select desired  
setting.  
˝
or  
˙
m
Exit menu from screen.  
Sound menu items  
Activities  
Treble  
Increase or decrease high frequency level.  
Increase or decrease low frequency level.  
Increase or decrease to adjust balance level.  
Select On to enable volume to remain at a pre-  
Bass  
Balance  
AVL (AutoVolume Leveller)  
determined level should there be a sudden change in  
volume during commercial breaks or channel switching.  
Incredible Surround  
Select between Mono and Spatial sound when  
transmission is in Mono and between Stereo and  
Incredible Surround sound when transmission in Stereo.  
Ultra Bass  
Select On to enjoy enhanced bass output.  
21  
15PT2302/p20-21  
21  
7/6/01, 1:35 PM  
USING THET IMER  
TheTimer feature allows you to set the timer to switch to another channel at a specified  
time while you are watching another channel or when theTV is on standby mode.  
Note : For the timer to function, the set must not be switched off. Once the set is switched  
off, the timer is disabled.  
Step  
Press button  
Result onTV Screen  
Display the main menu on screen.  
MENU  
Main  
o
Picture  
π Brightness  
Colour  
I
I
I
Sound  
Features  
Install  
Contrast  
Sharpness  
Colour Temp.  
More...  
œ
Main  
o
π
¸
Select Features.  
I
Picture  
Timer  
Child Lock  
Format  
I
Sound  
Features  
Install  
I
AutoPic. Booster  
œ
Enter the Features menu.  
˙
Features  
Timer  
o
π
Time  
I
I
I
Child Lock  
Format  
AutoPic. Booster  
Start Time  
Stop Time  
Channel  
Activate  
Display  
œ
EnterTimer menu.  
˙
Timer  
Time  
o
π
08:30  
Key in the current time starting from  
the hour follow by minute.  
This is the time where the “start time”  
and “stop time” will take reference  
from.  
2
5
8
0
1
4
7
3
6
9
I
I
I
I
I
Start Time  
Stop Time  
Channel  
Activate  
Display  
œ
o
Timer  
I
Time  
Start Timeπ 10:30  
Stop Time  
Channel  
Activate  
Display  
Select StartTime.  
¸
I
I
I
I
œ
2
5
8
0
1
4
7
3
6
9
Key in the time you want the  
programme to be switched on.  
22  
15PT2302/p22-28  
22  
7/6/01, 1:39 PM  
USING THET IMER  
Result onTV Screen  
Press button  
Step  
Select StopTime.  
¸
Timer  
o
I
Time  
Start Time  
I
Stop Time π 12:30  
I
Channel  
Activate  
Display  
œ
2
5
8
0
1
4
7
3
6
9
I
I
Key in the time you want the  
programme to be switched off.  
9
Select Channel.  
Timer  
Time  
o
¸
10  
11  
I
I
I
Start Time  
Stop Time  
Channel  
Activate  
Display  
2
5
8
0
1
4
7
3
6
9
π
œ
5
I
Key in the channel you want to  
switch to.  
I
Timer  
Time  
o
¸
Select Activate.  
I
12  
13  
I
I
I
Start Time  
Stop Time  
Channel  
Activate  
Display  
π
œ
Once  
Activate timer.You can select  
Once, Daily or Off.  
I
˙
¸
Select Display.  
14  
15  
Timer  
Time  
o
I
I
I
I
I
Start Time  
Stop Time  
Channel  
Activate  
Display  
Select On mode if you want to  
display the time on theTV screen.  
˙
π
œ
On  
Exit menu from screen.  
16  
m
Note :  
• After the StopTime is activated, theTV will go to standby mode  
immediately.  
• If StopTime is not keyed in, the set will go to standby mode after  
2 hours.  
To switch on set from standby mode, press Channel +/–,  
Digit (0 -9) or Power button.  
23  
15PT2302/p22-28  
23  
7/6/01, 1:39 PM  
ACTIVATING THE CHILD LOCK (ACCESSCODE)  
The Child Lock feature allows you to lock channels to prevent your children from watching  
programmes you deem undesirable.  
Note :You can only have access to the locked channels via the remote control. Keep the  
remote control out of reach so as to prevent your children from having access to it.  
Step  
Press button  
Result onTV Screen  
Display the main menu on screen.  
MENU  
Main  
o
I
Picture  
Sound  
Timer  
Child Lock  
I
Press button repeatedly until  
Features is selected.  
Features π Format  
I
¸
Install  
œ
Enter the Features menu.  
˙
Features  
Timer  
Child Lock  
Format  
o
π
I
Select Child Lock.  
¸
I
œ
o
π
Enter Child Lock mode.  
˙
Features  
Timer  
Child Lock  
Format  
I
Access Code  
xxxx  
Correct  
Key in the 4-digit access code.  
For the first time or if you have  
forgotten the access code, enter  
the universal access code 0711  
twice. It will now prompt you to  
key in a New Code.  
I
2
5
8
0
1
4
7
3
6
9
œ
Features  
Timer  
Child Lock  
Format  
o
π
I
New Code  
xxxx  
2
5
8
0
1
3
I
Key in your preferred code (4-digit).  
4
7
6
9
œ
o
Features  
Timer  
Child Lock  
Format  
Key in the new code the second  
time to confirm code.  
2
5
8
0
1
4
7
3
6
9
I
Confirm Code  
xxxx  
Confirmed  
π
I
The Child Lock menu will now  
appear. You can proceed to lock  
channel (refer to section on  
“Lock Channel”). If not, exit menu  
from screen.  
Child Lock  
o
I
I
I
I
Lock Channel  
π
002  
003  
004  
005  
006  
007  
Change Code  
Clear All  
Lock All  
9
m
œ
Note : After you have exit menu from screen and you want to  
enter the child lock menu again, you need to key the new  
access code only once.  
24  
15PT2302/p22-28  
24  
7/6/01, 1:39 PM  
ACTIVATING THE CHILD LOCK (CHANGE CODE)  
Note : You need to key the access code only once.  
Step  
Press button  
Result onTV Screen  
Repeat Steps 1 to 8 as  
in ACTIVATING THE  
CHILD LOCK  
The Child Lock menu will  
now appear. You can proceed  
to change code.  
Child Lock  
Lock Channel  
o
π
002  
003  
004  
005  
006  
007  
I
I
I
Change Code  
Clear All  
Lock All  
(ACCESS CODE)”  
œ
¸
Child Lock  
Lock Channel  
Change Code  
o
π
9
I
New Code  
----  
Select Change Code.  
10  
˙
I
Clear All  
Lock All  
I
Enter change code mode.  
œ
2
5
8
0
1
4
7
3
6
9
Child Lock  
Lock Channel  
Change Code  
o
π
11  
I
New Code  
xxxx  
Key in your preferred code  
(4-digit).  
I
Clear All  
Lock All  
I
œ
Child Lock  
Lock Channel Confirm Code  
Change Code π xxxx  
o
2
5
8
0
1
3
I
Key in the new code the  
second time to confirm  
code.  
12  
13  
4
7
6
9
I
Clear All  
Lock All  
Confirmed  
I
œ
m
Exit menu from screen.  
25  
15PT2302/p22-28  
25  
7/6/01, 1:39 PM  
ACTIVATING THE CHILD LOCK (LOCK CHANNEL)  
Result onTV Screen  
Press button  
Step  
Repeat Steps 1 to 8 as  
in CHILD Lock (ACCESS  
CODE)”  
The Child Lock menu will  
now appear. You can proceed  
to lock channel.  
Child Lock  
Lock Channel  
o
π
002  
003  
004  
005  
006  
007  
I
I
I
Change Code  
Clear All  
Lock All  
œ
Child Lock  
Lock Channel  
o
π
Enter lock channel mode.  
002  
003  
004  
005  
006  
007  
˙
9
I
I
I
Change Code  
Clear All  
Lock All  
π
œ
Select the channel you want  
to lock.  
Child Lock  
Lock Channel  
o
π
˚
or  
10  
002  
003  
004  
005  
006  
007  
I
I
I
Change Code  
Clear All  
Lock All  
¸
π
œ
Activate blocking of channel.  
A keylock symbol will appear  
beside the channel number  
indicating that it is locked.  
Note :To lock more than one  
channel, repeat Steps 10 to 11  
before exiting menu from  
screen.  
11  
Child Lock  
Lock Channel  
o
π
˙
002  
003  
004  
005  
006  
007  
I
I
I
Change Code  
Clear All  
Lock All  
π
F
œ
Exit menu from screen.  
12  
m
26  
15PT2302/p22-28  
26  
7/6/01, 1:39 PM  
ACTIVATING THE CHILD LOCK (LOCK ALL)  
You can choose to lock all channels in the LockAll mode in the Child Lock menu.  
Step  
Press button  
Result onTV Screen  
Repeat Steps 1 to 8 as  
in CHILD Lock (ACCESS  
CODE)”  
The Child Lock menu will  
now appear. You can proceed  
to lock all channels.  
Child Lock  
Lock Channel  
o
π
002  
003  
004  
005  
006  
007  
I
I
I
Change Code  
Clear All  
Lock All  
œ
Child Lock  
o
Select LockAll.  
¸
9
I
I
I
I
Lock Channel  
Change Code  
Clear All  
Select the On option to  
lock all channels.  
10  
Lock All  
π
œ
On  
˙
11  
m
Exit menu from screen.  
ACTIVATING THE CHILD LOCK (CLEAR ALL)  
To unlock channels that you have locked, enter the Child Lock menu and select the Off option  
ClearAll mode.  
Step  
Press button  
Result onTV Screen  
Repeat Steps 1 to 8 as  
in CHILD Lock (ACCESS  
CODE)”  
The Child Lock menu will  
now appear. You can proceed  
to clear all channels.  
Child Lock  
Lock Channel  
o
π
002  
003  
004  
005  
006  
007  
I
I
I
Change Code  
Clear All  
Lock All  
œ
o
π
Select Clear All.  
¸
9
Child Lock  
I
Lock Channel  
Change Code  
I
Select the Off option to  
unlock all channels.  
10  
Clear All  
Lock All  
Off  
˙
I
œ
Exit menu from screen.  
m
11  
27  
15PT2302/p22-28  
27  
7/6/01, 1:39 PM  
USING THE SCREEN FORMAT  
You can have a choice of two formats for your viewing pleasure, namely : - 4:3 mode and the  
EXPAND 4:3 mode through the FORMAT menu.  
Step  
Press button  
Result onTV Screen  
MENU  
Display the main menu on screen.  
Main  
o
π
I
Picture  
Sound  
Timer  
Child Lock  
Format  
I
Press button repeatedly until  
Features is selected.  
Features  
¸
I
Install  
AutoPic. Booster  
œ
Enter the Features menu.  
˙
Features  
o
I
Timer  
Child Lock  
I
Press button repeatedly umtil  
Format is selected.  
¸
Format  
4:3  
π
I
AutoPic Booster  
œ
Press the button repeatedly to  
cycle through the different formats  
(4:3 or Expand 4:3) and select  
your desired format.  
Features  
o
˙
m
I
Timer  
I
Child Lock  
Format  
4:3 Expandπ  
I
AutoPic Booster  
œ
Exit menu from screen.  
When to use the Screen Formats  
4:3 format  
Select the 4:3 format if you want to  
display the 4:3 picture using the full  
surface of the screen.  
Expand 4:3 format  
Select the Expand 4:3 format if you  
want to expand movie images  
recorded in the letterbox format.  
When this format is selected, the  
black horizontal bars at the top and  
bottom are expanded thus filling  
up the entireTV screen.  
28  
15PT2302/p22-28  
28  
7/6/01, 1:39 PM  
SMART PICTURE CONTROL  
Whether you are watching a movie or video game, yourTV has automatic video control  
settings matched to your current program source or content.The Smart Picture feature quickly  
resets yourTV’s video controls of program for a number of different types of programs and  
viewing conditions you may have in your home. Each Smart Picture setting is preset at the  
factory to automatically adjust theTV’s Brightness, Colour, Picture and Sharpness levels.  
Step  
Press button  
Press botton repeatedly to cycle through the 5 settings namely,  
DVD/VCD, Rich, Natural, Soft and Personal and select  
your desired picture setting.  
`
m
Exit menu from screen.  
Defintion of Picture Settings  
DVD/VCD : For optimal picture setting, whenever  
the source is connected to DVD/VCD  
player, select DVD/VCD setting for AV  
mode.  
DVD/VCD  
Rich  
: Emphasize very vibrant colours.This  
setting is the optimal setting when you  
are viewingTV programmes in a  
brightly-lit room.  
Rich  
Natural  
Soft  
: Emphasize original colours.  
Natural  
: Emphasize “warm” colours.  
(Suitable for dimly-lit room condition and  
givescinema-like effect when light is  
switched off).  
Soft  
Personal  
: Picture settings are set to your preference.  
Personal  
29  
15PT2302/p29-32  
29  
7/6/01, 1:44 PM  
SMART SOUND CONTROL  
Whether you are watching a movie or video game, yourTV has automatic sound control  
settings matched to your current program source or content.The Smart Sound feature quickly  
resets yourTV’s sound controls of program for a number of different types of programs and  
viewing conditions you may have in your home. Each Smart Sound setting is preset at the  
factory to automatically adjust theTV’sTreble and Bass levels.  
Step  
Press button  
Press botton repeatedly to cycle through the 4 settings namely,  
Theatre, Music, Voice and Personal and select your desired  
sound setting.  
q
Exit menu from screen.  
m
Definition of Sound Settings  
Theatre : Emphasize sensation to action.  
(Bass andTreble boosted)  
Theatre  
Music  
Voice  
: Emphasize low tone (Bass boosted).  
: Emphasize high tone (treble boosted).  
Music  
Voice  
Personal : Sound settings are set to your preference.  
Personal  
30  
15PT2302/p29-32  
30  
7/6/01, 1:44 PM  
PERSONAL ZAPPING  
A list or series of favouriteTV programs can be selected and stored in the 4 coloured buttons  
with the Personal Zapping feature.With this feature you can easily viewed up to a total of 10  
preferred channels for each coloured button.  
Adding Channels to the Favourite list  
Press button  
Step  
Result onTV Screen  
2
5
8
0
1
4
7
3
6
9
Select a channel by the Digit  
buttons  
8
Press button to display list.  
8
Select List!  
Choose your favourite colour  
button to store selected channel.  
Repeat steps 1 to 3 to add and  
store your avourite channels to  
the list.  
Added!  
8
Exit menu from screen.  
m
To view through the favourite list  
Press the colour button that you have selected.  
Press button repeatedly to cycle through your favourite list  
and view your favourite channel.  
Deleting Channels from the Favourite list  
Select a colour button and press  
button repeatedly to select the  
channel you want to delete.  
8
8
Remove Item?- Press  
Press button to display list.  
Press button to remove item.  
Repeat steps 1 to 3 to delete  
more channels from list.  
Exit menu from screen.  
m
31  
15PT2302/p29-32  
31  
7/6/01, 1:44 PM  
AUTOMATIC PICTURE BOOSTER  
If the transmission signal is weak, the Automatic Picture Booster built into theTV set will  
increase the signal level to provide a good picture at all times.You have a choice to turn on/off  
the feature, depending on the signal conditions locally.  
Step  
Press button  
Result onTV Screen  
Display the main menu on screen.  
MENU  
Main  
o
Picture  
π Brightness  
Colour  
I
I
I
Sound  
Features  
Install  
Contrast  
Sharpness  
Colour Temp.  
More...  
œ
¸
Select Features.  
Main  
o
I
Picture  
Sound  
Timer  
Child Lock  
I
Features π Format  
I
Install  
Auto Pic. Booster  
œ
o
Enter the Features menu.  
˙
Select Auto Pic.Booster.  
Features  
¸
I
Timer  
I
Child Lock  
Format  
I
Auto Pic. Booster  
π
Off  
œ
Select On.  
Features  
o
˙
m
I
Timer  
I
Child Lock  
Format  
I
Auto Pic. Booster  
π
On  
œ
Exit menu from screen.  
32  
15PT2302/p29-32  
32  
7/6/01, 1:44 PM  
USING THE TELETEXT  
If aTV channel broadcast contains teletext information, each channel that broadcasts  
teletext transmits a page (index page) with information on how to use the teletext system,  
usually on page 100.The system transmitted is indicated in the option line at the bottom  
of the screen.  
Result onTV Screen  
Press button  
& On/Off teletext  
and  
Press the button once to switch on  
teletext display. (A channel in which  
teletext is being transmitted must be  
selected).  
Superimpose  
teletext page  
overTV  
Press the button the second time  
superimpose the teletext page over  
theTV programme.  
(
&
programme  
Press the button the third time  
to exit teletext mode.  
b
é Selecting a  
Key in the required teletext page  
(3 digits).The page number is  
teletext page  
displayed at the top left hand corner  
of the screen. When the teletext  
page is located, the counter stops  
searching. If the counter keeps  
searching, it means that the page is  
not available for selection. If you  
make a mistake in keying the page  
number, you have to complete  
keying the 3-digit number before  
re-keying the correct page number.  
2
5
8
0
1
4
7
3
6
9
é
Accessing  
a teletext  
page  
Press the CURSOR UP button to  
display the next page and the  
CURSOR DOWN button to  
display the previous page.  
˚
¸
Direct Access to The 4-colour buttons allow you to  
an item or  
corresponding  
pages  
access directly an item or  
corresponding pages.  
( Main Index  
Press the button to return to the  
main index page.  
d
33  
15PT2302/p33-35  
33  
7/6/01, 1:47 PM  
USING THE TELETEXT  
Press button  
Result onTV Screen  
§ Interrupt  
Press the button to change toTV  
mode. Press the button again to  
return to teletext mode and to the  
teletext page.  
!
ç
§
è
a
è Enlarge  
Press the button once to enlarge  
and view the top half of the page.  
Press the button the second time  
to enlarge and view the bottom  
half of the page. Press the button  
the third time to return to normal  
size page.  
h
! Hold  
A selected page sometimes  
f
contains a few sub-pages.The sub-  
page will automatically move to the  
next sub-page after about 20  
seconds.The total number of sub-  
pages are indicated at the top right  
hand corner of the screen. Press  
the button once to hold page and  
the second time to release holding  
of page.  
ç Reveal/  
Press the button once to reveal  
hidden information (solutions to  
puzzles, riddles, etc). Press the  
button the second time to conceal  
information.  
Conceal  
e
This button is applicable only to  
teletext page with puzzles,riddles,  
etc.)  
34  
15PT2302/p33-35  
34  
7/6/01, 1:47 PM  
SPECIFICATIONS  
15PT2302  
370 mm  
Picture tube screen size  
Picture tube visible area  
355 mm  
Audio Output :  
Speaker  
2 x 3 W  
TV System  
NTSC M  
PAL B/G  
PAL D/K  
PAL I  
SECAM B/G  
SECAM D/K  
SECAM K1  
Set Dimensions :  
Width  
Depth  
403 mm  
444 mm  
357 mm  
Height  
NetWeight of Set  
approximate 13 kg  
Note  
For OperatingVoltage, Frequency, Power Consumption andVersion Number, refer to the  
type number at the rear of the set.  
35  
15PT2302/p33-35  
35  
7/6/01, 2:02 PM  

Rockford Fosgate FNP2414 User Manual
Raypak Hi Delta 302A 902A User Manual
Plantronics Bluetooth Headset C720 User Manual
Pioneer BDP 52FD User Manual
Philips HR1840 User Manual
Nikon Riflescope MONARCH III User Manual
Marshall electronic V R902DP AFHD User Manual
Linear Car Stereo System User Manual
Kodak EASYSHARE Z1485 IS User Manual
JVC GY HM100U User Manual