FujiFilm X S1 User Manual

For Your Safety  
Power Lines: An outside antenna sys-  
tem should not be located in the  
vicinity of overhead power lines or  
other electric light or power circuits,  
or where it can fall into such power  
lines or circuits. When installing an  
outside antenna system, extreme  
care should be taken to keep from  
touching such power lines or circuits  
as contact with them might be fatal.  
Replacement Parts: When replace-  
ment parts are required, be sure  
the service technician has used  
replacement parts specified by the  
manufacturer or have the same  
characteristics as the original part.  
Unauthorized substitutions may  
result in fire, electric shock or other  
hazards.  
Use  
Service  
Cleaning: Unplug this video product Servicing: Do not attempt to service  
from the wall outlet before clean- this video product yourself as open-  
ing. Do not use liquid cleaners or ing or removing covers may expose  
aerosol cleaners. Use a damp cloth you to dangerous voltage or other  
for cleaning.  
hazards. Refer all servicing to quali-  
fied service personnel.  
Object and Liquid Entry: Never push  
objects of any kind into this video Damage Requiring Service: Unplug this  
product through openings as they video product from the wall outlet  
may touch dangerous voltage and refer servicing to qualified ser-  
points or short out parts that could vice personnel under the following  
result in a fire or electric shock. Never conditions:  
Safety Check: Upon completion of any  
service or repairs to this video prod-  
uct, ask the service technician to  
perform safety checks to determine  
that the video product is in proper  
operating condition.  
EXAMPLE OF ANTENNA GROUNDING  
AS PER NATIONAL ELECTRICAL CODE  
spill liquid of any kind on the video When the power-supply cord or  
product.  
Ground Clamp  
Antenna  
plug is damaged.  
Lead in Wire  
If liquid has been spilled, or objects  
have fallen into the video product.  
If the video product has been ex-  
posed to rain or water.  
If the video product has been  
dropped or the cabinet has been  
damaged.  
If the video product does not op-  
erate normally be following the  
operating instructions. Adjust only  
those controls that are covered by  
the operating instructions as an im-  
proper adjustment of other controls  
may result in damage and will often  
require extensive work by a qualified  
technician to restore the video prod-  
uct to its normal operation.  
Lightning: For added protection for  
this video product receiver during  
a lightning storm, or when it is left  
unattended and unused for long pe-  
Electric  
Service  
Equipment  
Antenna  
Discharge Unit riods of time, unplug it from the wall  
(NEC SECTION  
810-20)  
Grounding  
Conductors  
(NEC SECTION  
810-21)  
Ground  
Clamps  
outlet and disconnect the antenna  
or cable system. This will prevent  
damage to the video product due  
to lightning and power-line surges.  
Power Service  
Grounding Electrode  
System (NEC ART 250.  
PART H)  
When the video product exhibits a  
distinct change in performance - this  
indicates a need for service.  
iii  
For Your Safety  
Be sure to read this notes before using  
Safety Notes  
WARNING  
Do not allow water or foreign objects to enter the camera.  
If water or foreign objects get inside the camera, turn the camera  
off, remove the battery and disconnect and unplug the AC power  
adapter.  
• Make sure that you use your camera correctly. Read these Safety Notes and  
your Owner’s Manual carefully before use.  
Avoid  
exposure to  
water  
Continued use of the camera can cause a fire or electric shock.  
• Contact your FUJIFILM dealer.  
• After reading these Safety Notes, store them in a safe place.  
About the Icons  
Do not use the camera in the bathroom or shower.  
This can cause a fire or electric shock.  
The icons shown below are used in this document to indicate the severity of  
the injury or damage that can result if the information indicated by the icon  
is ignored and the product is used incorrectly as a result.  
Do not use in  
the bathroom  
or shower.  
Never attempt to disassemble or modify (never open the case).  
Failure to observe this precaution can cause fire or electric shock.  
This icon indicates that death or serious injury can result if the infor-  
mation is ignored.  
Do not disas-  
semble  
WARNING  
Should the case break open as the result of a fall or other accident, do not touch  
the exposed parts.  
Failure to observe this precaution could result in electric shock or in  
injury from touching the damaged parts. Remove the battery im-  
mediately, taking care to avoid injury or electric shock, and take the  
product to the point of purchase for consultation.  
This icon indicates that personal injury or material damage can result  
if the information is ignored.  
CAUTION  
Do not touch  
internal  
parts  
The icons shown below are used to indicate the nature of the information  
which is to be observed.  
Triangular icons tell you that this information requires attention (“im-  
portant”).  
Do not change, heat or unduly twist or pull the connection cord and do not  
place heavy objects on the connection cord.  
These actions could damage the cord and cause a fire or electric  
shock.  
• If the cord is damaged, contact your FUJIFILM dealer.  
Circular icons with a diagonal bar tell you that the action indicated is  
prohibited (“Prohibited”).  
Filled circles with an exclamation mark tell you an action that must be  
performed (“Required”).  
Do not place the camera on an unstable surface.  
This can cause the camera to fall or tip over and cause injury.  
Never attempt to take pictures while in motion.  
Do not use the camera while you are walking or driving a vehicle. This  
can result in you falling down or being involved in a traffic accident.  
Do not touch any metal parts of the camera during a thunderstorm.  
This can cause an electric shock due to induced current from the  
lightning discharge.  
WARNING  
If a problem arises, turn the camera off, remove the battery, disconnect and  
unplug the AC power adapter.  
Continued use of the camera when it is emitting smoke, is emitting  
any unusual odor, or is in any other abnormal state can cause a fire  
Unplug  
from power  
socket.  
or electric shock.  
Do not use the battery except as specified.  
Load the battery as aligned with the indicator.  
• Contact your FUJIFILM dealer.  
iv  
For Your Safety  
WARNING  
CAUTION  
Do not heat, change or take apart the battery. Do not drop or subject the bat-  
tery to impacts. Do not store the battery with metallic products. Do not use  
chargers other than the specified model to charge the battery.  
Any of these actions can cause the battery to burst or leak and cause  
fire or injury as a result.  
Keep out of the reach of small children.  
This product could cause injury in the hands of a child.  
Do not place heavy objects on the camera.  
This can cause the heavy object to tip over or fall and cause injury.  
Do not move the camera while the AC power adapter is still connected. Do not  
pull on the connection cord to disconnect the AC power adapter.  
This can damage the power cord or cables and cause a fire or electric  
shock.  
Do not use the AC power adapter when the plug is damaged or the plug socket  
connection is loose.  
Use only the battery or AC power adapters specified for use with this camera.  
Do not use voltages other than the power supply voltage shown.  
The use of other power sources can cause a fire.  
If the battery leaks and fluid gets in contact with your eyes, skin or clothing.  
Flush the affected area with clean water and seek medical attention or call an  
emergency number right away.  
This could cause a fire or electric shock.  
Do not use the charger to charge batteries other than those specified here.  
The Ni-MH battery charger is designed for FUJIFILM HR-AA Ni-MH  
batteries. Using the charger to charge conventional batteries or other  
types of rechargeable batteries can cause the battery to leak fluid,  
overheat or burst.  
Do not cover or wrap the camera or the AC power adapter in a cloth or blanket.  
This can cause heat to build up and distort the casing or cause a fire.  
When you are cleaning the camera or you do not plan to use the camera for  
an extended period, remove the battery and disconnect and unplug the AC  
power adapter.  
Danger of explosion if battery is incorrectly replaced. Replace only with the  
same or equivalent type.  
Failure to do so can cause a fire or electric shock.  
When charging ends, unplug the charger from the power socket.  
Leaving the charger plugged into the power socket can cause a fire.  
When carrying the battery, install it in a digital camera or keep it in the hard  
case. When storing the battery, keep it in the hard case. When discarding,  
cover the battery terminals with insulation tape.  
Contact with other metallic objects or battery could cause the bat-  
tery to ignite or burst.  
Using a flash too close to a person’s eyes may temporarily affect the eyesight.  
Take particular care when photographing infants and young children.  
When a memory card is removed, the card could come out of the slot too quick-  
ly. Use your finger to hold it and gently release the card.  
Keep Memory Cards out of the reach of small children.  
Because Memory Cards are small, they can be swallowed by children.  
Be sure to store Memory Cards out of the reach of small children. If  
a child swallows a Memory Card, seek medical attention or call an  
emergency number.  
Request regular internal testing and cleaning for your camera.  
Build-up of dust in your camera can cause a fire or electric shock.  
• Contact your FUJIFILM dealer to request internal cleaning every 2  
years.  
• Please note this is not a free of charge service.  
Remove your fingers from the flash window before the flash fires.  
Failure to observe this precaution could result in burns.  
CAUTION  
Do not use this camera in locations affected by oil fumes, steam, humidity or  
dust.  
Keep the flash window clean and do not use the flash if the window is ob-  
structed.  
Failure to observe these precautions could cause smoke or discolor-  
ation.  
This can cause a fire or electric shock.  
Do not leave this camera in places subject to extremely high temperatures.  
Do not leave the camera in locations such as a sealed vehicle or in  
direct sunlight. This can cause a fire.  
v
For Your Safety  
If you are using a heating pad, take  
care not to place the battery di-  
rectly against the pad. The camera  
may not operate if you use a de-  
pleted battery in cold conditions.  
• Dispose of used battery promptly.  
• Do not drop the battery or other-  
wise subject it to strong impacts.  
• Do not expose the battery to wa-  
ter.  
Battery Life  
Power Supply and Battery  
At normal temperatures, the bat-  
tery can be used at least 300 times.  
If the time for which the battery  
provides power shortens markedly,  
this indicates that the battery has  
reached the end of its effective life  
and should be replaced.  
* Confirm your battery type before read-  
ing the following descriptions.  
The following explains proper use of  
batteries and how to prolong their  
• Always keep the battery terminals  
clean.  
life. Incorrect use of batteries can Charging the Battery  
cause shorter battery life, as well as • You can charge the battery using  
• Do not store batteries in hot plac-  
es. Also, if you use the battery for  
a long period, the camera body  
and the battery itself will become  
warm. This is normal. Use the AC  
power adapter if you are taking  
pictures or viewing images for a  
long period of time.  
leakage, excessive heat, fire or explo-  
sion.  
the battery charger (included).  
- The battery can be charged  
at ambient temperatures be-  
tween 0°C and +40°C (+32°F  
and +104°F). Refer to the Owner’s  
Manual for the time of charging  
battery.  
- You should charge the battery  
at an ambient temperature be-  
tween +10°C and +35°C (+50°F  
and +95°F). If you charge the  
battery at a temperature outside  
this range, charging takes longer  
because the performance of the  
battery is impaired.  
- You cannot charge the battery  
at temperatures of 0°C (+32°F) or  
below.  
• The Rechargeable Lithium-ion Bat-  
tery does not need to be fully dis-  
charged or exhausted flat before  
being charged.  
Notes on storage  
• If  
a
battery is stored for long  
Camera uses the Rechargeable  
Lithium-ion Battery  
1
periods while charged, the per-  
formance of the battery can be  
impaired. If the battery will not be  
used for some time, run the battery  
out before storing it.  
• If you do not intend to use the  
camera for a long period of time,  
remove the battery from the cam-  
era.  
• Store the battery in a cool place.  
- The battery should be stored in  
a dry location with an ambient  
temperature between +15°C and  
+25°C (+59°F and +77°F).  
* When shipped, the battery is not  
fully charged. Always charge the  
battery before using it.  
* When carrying the battery, install it  
in a digital camera or keep it in the  
soft case.  
Camera uses AA-size alkaline or Ni-MH  
(nickel-metal hydride) rechargeable  
batteries  
2
Battery Features  
* For details on the batteries that  
you can use, refer to the Owner’s  
Manual of your camera.  
• The battery gradually loses its  
charge even when not used. Use  
a battery that has been charged  
recently (in the last day or two) to  
take pictures.  
Cautions for Using Battery  
• Do not heat the batteries or throw  
them into a fire.  
• Do not carry or store batteries with  
metal objects such as necklaces or  
hairpins.  
• Do not expose the batteries to  
water, and keep batteries from get-  
ting wet or stored in moist loca-  
tions.  
• Do not attempt to take apart or  
change the batteries, including  
battery casings.  
- Do not leave the battery in hot or  
extremely cold places.  
• To maximize the life of the battery,  
turn the camera off as quickly as  
possible when it is not being used.  
• The number of available frames  
will be lower in cold locations or  
at low temperatures. Take along  
a spare fully charged battery. You  
can also increase the amount of  
power produced by putting the  
battery in your pocket or another  
warm place to heat it and then  
loading it into the camera just be-  
fore you take a picture.  
Handling the Battery  
Cautions for Your Safety:  
• Do not carry or store battery with  
metal objects such as necklaces or  
hairpins.  
• Do not heat the battery or throw it  
into a fire.  
• Do not attempt to take apart or  
change the battery.  
• Do not recharge the battery with  
chargers other those specified.  
• The battery may feel warm after it  
has been charged or immediately  
after being used. This is perfectly  
normal.  
• Do not recharge a fully charged  
battery.  
• Do not subject the batteries to  
strong impacts.  
vi  
For Your Safety  
• Do not use batteries that are leak-  
ing, deformed, discolored.  
• Do not store batteries in warm or  
humid places.  
• Keep the batteries out of reach of  
babies and small children.  
• Make sure that the battery polarity  
(Cand D) is correct.  
• Do not use new with used batter-  
ies. Do not use charged and dis-  
charged batteries together.  
• Do not use different types or  
brands of batteries at the same  
time.  
• If you do not intend to use the  
camera for a long period of time,  
remove the batteries from the  
camera. Note if the camera is left  
with the batteries removed, the  
time and date settings are cleared.  
• The batteries feel warm right after  
being used. Before removing the  
batteries, turn the camera off and  
wait for the batteries to cool down.  
• Since batteries do not work well in  
cold weather or locations, warm  
the batteries by placing them in-  
side your garments before use.  
Batteries do not work well when  
cold. They will work again when  
the temperature returns to normal.  
• Soil (such as fingerprints) on the  
battery terminals makes the bat-  
teries charge less reducing the  
number of images. Carefully wipe  
the battery terminals with a soft  
dry cloth before loading.  
If any liquid at all leaks from  
the batteries, wipe the battery  
compartment thoroughly and  
then load new batteries.  
• Ni-MH batteries have  
a
limited  
CAUTION  
service life. If a battery can only  
be used for a short time even after  
repeated discharge-charge cycles,  
it may have reached the end of its  
service life.  
Do not use the “Discharging re-  
chargeable batteries” function when  
alkaline batteries being used.  
• To charge Ni-MH batteries, use the  
quick battery charger (sold sepa-  
rately). Refer to the instructions  
supplied with the charger to make  
sure that the charger is used cor-  
rectly.  
If any battery fluid comes into  
contact with your hands or  
clothing, flush the area thor-  
oughly with water. Note that  
battery fluid can cause loss  
of eyesight if it gets into your  
eyes. If this occurs, do not rub  
your eyes. Flush the fluid out  
with clean water and contact  
your physician for treatment.  
Disposing of Batteries  
• When disposing of batteries, do  
so in accordance with your local  
waste disposal regulations.  
• Do not use the battery charger to  
charge other batteries.  
• Note that the batteries feel warm  
after being charged.  
Notes on both models (  
,
)
3
1
2
AC Power Adapter  
Always use the AC Power Adapter  
with the camera. The use of an AC  
Power adapter other than FUJIFILM  
AC Power Adapter can be damaged  
to your digital camera.  
For details on the AC power adapter,  
refer to the Owner’s Manual of your  
camera.  
• Due to the way the camera is con-  
structed, a small amount of current  
is used even when the camera is  
turned off. Note in particular that  
leaving Ni-MH batteries in the  
camera for a long period will over-  
discharge the batteries and may  
render them unusable even after  
recharging.  
• Ni-MH batteries will self-discharge  
even when not used, and the time  
for which they can be used may be  
shortened as a result.  
• Ni-MH batteries will deteriorate  
rapidly if over-discharged (e.g.  
by discharging the batteries in a  
flashlight). Use the “Discharging re-  
chargeable batteries” function pro-  
vided in the camera to discharge  
the batteries.  
Using the AA-size Ni-MH batteries  
correctly  
• Ni-MH batteries left unused in  
storage for long periods can be-  
come “deactivated”. Also, repeat-  
edly charging Ni-MH batteries  
that are only partially discharged  
can cause them to suffer from the  
“memory effect”. Ni-MH batteries  
that are “deactivated” or affected  
by “memory” suffer from the prob-  
lem of only providing power for a  
short time after being charged. To  
prevent this problem, discharge  
and recharge them several times  
using the camera’s “Discharging  
rechargeable batteries” function.  
Deactivation and memory are spe-  
cific to Ni-MH batteries and are not  
in fact battery faults.  
• Use the AC power adapter for in-  
door use only.  
• Plug the connection cord plug se-  
curely into the DC input terminal.  
• Turn off the FUJIFILM Digital cam-  
era before disconnecting the cord  
from the DC input terminal. To dis-  
connect, pull out the plug gently.  
Do not pull on the cord.  
• Do not use the AC power adapter  
with any device other than your  
camera.  
• During use, the AC power adapter  
will become hot to the touch. This  
is normal.  
See Owner’s Manual for the proce-  
dure for “Discharging rechargeable  
batteries”.  
vii  
For Your Safety  
• Do not take apart the AC power unless intended only for personal Although the LCD panel is produced  
adapter. Doing so could be dan- use. Note that some restrictions ap- with highly sophisticated technolo-  
Explanation of Color Television  
System  
NTSC: National Television System  
Committee, color television  
gerous.  
• Do not use the AC power adapter performances, entertainments and permanently lit spots. This is not a  
in a hot and humid place. exhibits, even when intended purely malfunction, and does not affect re-  
• Do not subject the AC power for personal use. Users are also asked corded images.  
adapter to strong shocks. to note that the transfer of Memory  
• The AC power adapter may emit a Card containing images or data pro-  
ply to the photographing of stage gies, there may be black spots or  
telecasting  
specifications  
adopted mainly in the U.S.A.,  
Canada and Japan.  
Trademark Information  
xD-Picture Card and Eare trade- PAL: Phase Alternation by Line, a  
humming. This is normal.  
• If used near a radio, the AC power permissible within the restrictions  
adapter may cause static. If this imposed by those copyright laws.  
happens, move the camera away  
from the radio.  
tected under copyright laws is only  
marks of FUJIFILM Corporation. The  
typefaces included herein are solely  
developed by DynaComware Tai-  
wan Inc. Macintosh, QuickTime, and  
color television system ad-  
opted mainly by European  
countries and China.  
Handling Your Digital Camera  
Exif Print (Exif ver. 2.3)  
To ensure that images are recorded Mac OS are trademarks of Apple Inc.  
correctly, do not subject the camera in the U.S.A. and other countries.  
to impact or shock while an image is Windows 7, Windows Vista, and the  
Exif Print Format is a newly revised  
digital camera file format that con-  
tains a variety of shooting informa-  
tion for optimal printing.  
Before Using the Camera  
Do not aim the camera at extremely  
bright light sources, such as the sun  
in a cloudless sky. Failure to observe  
this precaution could damage the  
camera image sensor.  
being recorded.  
Windows logo are trademarks of  
the Microsoft group of companies.  
Adobe and Adobe Reader are either  
trademarks or registered trademarks  
of Adobe Systems Incorporated in  
the U.S.A. and/or other countries.  
The SDHC and SDXC logos are trade-  
marks of SD-3C, LLC. The HDMI logo  
is a trademark. YouTube is a trade-  
mark of Google Inc. All other trade  
names mentioned in this manual are  
the trademarks or registered trade-  
marks of their respective owners.  
Liquid Crystal  
If the LCD monitor is damaged, take  
particular care with the liquid crystal  
in the monitor. If any of the follow-  
ing situations arise, take the urgent  
action indicated.  
IMPORTANT NOTICE: Read Before  
Using the Software  
Direct or indirect export, in whole or  
in part, of licensed software without  
the permission of the applicable  
governing bodies is prohibited.  
Test Shots Prior to Photography  
For important photographs (such as  
weddings and overseas trips), always  
take a test shot and view the im-  
age to make sure that the camera is  
working normally.  
• FUJIFILM Corporation cannot ac-  
cept liability for any incidental  
losses (such as the costs of photog-  
raphy or the loss of income from  
photography) incurred as a result  
of faults with this product.  
• If liquid crystal comes in contact  
with your skin:  
Wipe the area with  
a
cloth and  
then wash thoroughly with soap  
and running water.  
• If liquid crystal gets into your eye:  
Flush the affected eye with clean Notes on Electrical Interference  
water for at least 15 minutes and If the camera is to be used in hos-  
then seek medical assistance.  
• If liquid crystal is swallowed:  
pitals or aircrafts, please note that  
this camera may cause interference  
Flush your mouth thoroughly with to other equipment in the hospital  
water. Drink large quantities of wa- or aircraft. For details, please check  
ter and induce vomiting. Then seek with the applicable regulations.  
medical assistance.  
Notes on Copyright  
Images recorded using your digital  
camera system cannot be used in  
ways that infringe copyright laws  
without the consent of the owner,  
viii  
For Your Safety  
• You are cautioned that any changes or modifications In Countries Outside the European Union, Norway, Iceland and  
not expressly approved in this manual could void the Liechtenstein: If you wish to discard this product, includ-  
NOTICCEES  
To prevent fire or shock hazard, do not expose the unit  
to rain or moisture.  
user’s authority to operate the equipment.  
ing the batteries or accumulators, please contact your  
local authorities and ask for the correct way of disposal.  
Notes on the Grant: To comply with Part 15 of the FCC  
Rules, this product must be used with a Fujifilm-spec-  
ified ferrite-core A/V cable, USB cable, and DC supply  
cord.  
Please read the “Safety Notes” and make sure you un-  
derstand them before using the camera.  
EC Declaaratioon of Coonformity  
We  
Perchlorate Material—special handling may apply. See  
http://www.dtsc.ca.gov/hazardouswaste/perchlorate.  
Name:  
Address:  
FUJIFILM Electronic Imaging Europe GmbH  
Benzstrasse 2 47533 Kleve, Germany  
For Customers in Canada  
CAUTION: This Class B digital apparatus complies with  
Canadian ICES-003.  
declare that the product  
Product Name: FUJIFILM DIGITAL CAMERA X-S1  
Manufacturer’s  
For Customers in the U. S. A.  
Tested To Comply With FCC Standards  
FOR HOME OR OFFICE USE  
Name:  
Manufacturer’s 7-3, AKASAKA 9-CHOME, MINATO-KU,  
Address: TOKYO, 107-0052 JAPAN  
conforms to the following Standards:  
FUJIFILM Corporation  
Disposall of Electrical and Electronic Equipment in Private  
Houseeholds  
FCC Statement: This device complies with Part 15 of the  
FCC Rules. Operation is subject to the following two  
conditions: (1) This device may not cause harmful in-  
terference, and (2) this device must accept any interfer-  
ence received, including interference that may cause  
undesired operation.  
In the European Union, Norway, Iceland and Liech-  
tenstein: This symbol on the product, or in  
the manual and in the warranty, and/or on  
its packaging indicates that this product  
shall not be treated as household waste.  
Instead it should be taken to an applicable  
collection point for the recycling of electri-  
cal and electronic equipment.  
Safety:  
EMC:  
EN60065: 2002 + A1: 2006 + A11: 2008  
EN55022: 2006 + A1: 2007 Class B  
EN55024: 1998 + A1: 2001 + A2: 2003  
EN61000-3-2: 2006  
CAUTION: This equipment has been tested and found  
to comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against  
harmful interference in a residential installation. This  
equipment generates, uses, and can radiate radio  
frequency energy and, if not installed and used in ac-  
cordance with the instructions, may cause harmful  
interference to radio communications. However, there  
is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause  
harmful interference to radio or television reception,  
which can be determined by turning the equipment  
off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna.  
EN61000-3-3: 2008  
following the provision of the EMC Directive (2004/108/EC)  
and Low Voltage Directive (2006/95/EC).  
By ensuring this product is disposed of correctly, you  
will help prevent potential negative consequences to  
the environment and human health, which could oth-  
erwise be caused by inappropriate waste handling of  
this product.  
Kleve,  
Germany  
Nobember 1,  
2011  
This symbol on the batteries or accumula-  
tors indicates that those batteries shall not  
be treated as household waste.  
Place  
Date  
Signature, Managing  
Director  
If your equipment contains easy removable batteries or  
accumulators please dispose these separately accord-  
ing to your local requirements.  
• Increase the separation between the equipment and  
receiver.  
• Connect the equipment into an outlet on a circuit dif-  
ferent from that to which the receiver is connected.  
• Consult the dealer or an experienced radio/TV techni-  
cian for help.  
The recycling of materials will help to conserve natural  
resources. For more detailed information about recy-  
cling this product, please contact your local city office,  
your household waste disposal service or the shop  
where you purchased the product.  
ix  
About This Manual  
Before using the camera, read this manual and the warnings on pages ii–ix. For information on specific  
topics, consult the sources below.  
Table of Contents .............................................. Pxi Troubleshooting ............................................ P110  
The “Table of Contents” gives an overview of the Having a specific problem with the camera?  
entire manual. The principal camera operations Find the answer here.  
are listed here.  
Warning Messaaggeess aanndd DDiissppllaayyss ..................... P115  
Find out what’s behind that flashing icon or error  
message in the display.  
Memory Cards  
Pictures can be stored in the camera’s internal memory or on optional SD, SDHC, and SDXC memory cards (P14),  
referred to in this manual as “memory cards”.  
Temperature Warning  
The camera will turn off automatically before its temperature or the temperature of the battery rise above safe  
limits. Pictures taken when a temperature warning is displayed may exhibit higher levels of “noise” (mottling).  
Turn the camera off and wait for it to cool before turning it on again.  
Camera Body Care  
For continued enjoyment of your camera, use a soft, dry cloth to clean the camera body after each use. Do not  
use alcohol, thinner, or other volatile chemicals, which could discolor or deform the leather on the camera body.  
Any liquid on the camera should be removed immediately with a soft, dry cloth.  
x
Table of Contents  
For Your Safety ................................................................................. ii  
IMPORTANT SAFETY INSTRUCTIONS...................................... ii  
Safety Notes.................................................................................... iv  
About This Manual.......................................................................... x  
Mooree on PPhotography  
Shooting Mode...............................................................................22  
P: PROGRAM AE............................................................................23  
S: SHUTTER PRIORITY AE...........................................................24  
A: APERTURE PRIORITY AE........................................................24  
M: MANUAL ....................................................................................25  
C1/C2/C3: CUSTOM MODE.......................................................26  
EXR (E AUTO/E Priority) .......................................27  
BAUTO ..........................................................................................28  
Adv. ADVANCED...........................................................................28  
SP SCENE POSITION ....................................................................32  
Focus Lock.........................................................................................34  
The AE/AF LOCK Button.....................................................................35  
Locking Exposure......................................................................35  
Locking Focus.............................................................................35  
FMacro and Super Macro Modes (Close-ups)................36  
NUsing the Flash (Super-Intelligent Flash).......................37  
JUsing the Self-Timer...............................................................39  
Continuous Shooting (Burst Mode/Bracketing)..............40  
dExposure Compensation.....................................................44  
Metering ............................................................................................45  
Focus Mode ......................................................................................46  
Focus Frame Selection ................................................................48  
Sensitivity .........................................................................................49  
White Balance..................................................................................50  
The Fn Button..................................................................................52  
bIntelligent Face Detection..................................................53  
Beffoore Yoou Beggin  
Introduction....................................................................................... 1  
Symbols and Conventions.......................................................... 1  
Supplied Accessories.................................................................... 1  
Parts of the Camera....................................................................... 2  
Camera Displays .......................................................................... 5  
First SSteps  
Attaching Accessories ................................................................... 8  
The Strap......................................................................................... 8  
The Lens Cap................................................................................. 8  
The Lens Hood ............................................................................. 8  
Charging the Battery ..................................................................... 9  
Inserting the Battery....................................................................10  
Inserting a Memory Card ...........................................................12  
Turning the Camera on and Off ..............................................15  
Basic Setup .......................................................................................16  
Basic Photoggrraphy annd Pllayybbaacckk  
Taking Pictures ...............................................................................17  
Viewing Pictures ............................................................................21  
xi  
Table of Contents  
nFace Recognition ....................................................................54  
Adding New Faces .......................................................................54  
Viewing, Editing, and Deleting Existing Data ...................55  
Taking RAW Pictures ....................................................................56  
Connecctions  
Viewing Pictures on TV...............................................................69  
Printing Pictures via USB............................................................71  
Connecting the Camera ............................................................71  
Printing Selected Pictures ........................................................71  
Printing the DPOF Print Order.................................................72  
Creating a DPOF Print Order....................................................74  
Viewing Pictures on a Computer............................................77  
Windows: Installing MyFinePix Studio.................................77  
Macintosh: Installing FinePixViewer.....................................79  
Connecting the Camera ............................................................81  
More on Pllayback  
Playback Options...........................................................................57  
Continuous Shooting .................................................................57  
IFavorites: Rating Pictures ....................................................57  
Playback Zoom..............................................................................58  
Multi-Frame Playback.................................................................59  
ADeleting Pictures ....................................................................60  
Viewing Photo Information ......................................................61  
Image Search...................................................................................62  
XPhotoBook Assist ...................................................................63  
Creating a PhotoBook ................................................................63  
Viewing PhotoBooks ..................................................................64  
Editing and Deleting PhotoBooks.........................................64  
Viewing Panoramas......................................................................65  
Menus  
Using the Menus: Shooting Mode .........................................83  
Using the Shooting Menu.........................................................83  
Shooting Menu Options............................................................83  
AE MODE ..........................................................................83  
AAdv. MODE..............................................................................83  
A
SCENE POSITION.....................................................................83  
NISO...............................................................................................83  
OIMAGE SIZE...............................................................................84  
TIMAGE QUALITY.....................................................................84  
UDYNAMIC RANGE ..................................................................85  
PFILM SIMULATION.................................................................85  
dWB SHIFT ..................................................................................86  
fCOLOR........................................................................................86  
HSHARPNESS..............................................................................86  
rHIGHLIGHT TONE ..................................................................86  
sSHADOW TONE ......................................................................86  
hNOISE REDUCTION................................................................86  
Movies  
Recording Movies..........................................................................66  
Movie Frame Size .........................................................................67  
aViewing Movies........................................................................68  
xii  
Table of Contents  
RINTELLIGENT DIGITAL ZOOM............................................86  
ZADVANCED ANTI BLUR........................................................86  
bFACE DETECTION...................................................................86  
FAF MODE...................................................................................87  
nFACE RECOGNITION..............................................................87  
WMOVIE MODE ..........................................................................87  
a STILL SHOOTING IN MOVIE................................................88  
IFLASH.........................................................................................88  
gEXTERNAL FLASH..................................................................88  
KCUSTOM SET............................................................................89  
vDISP. CUSTOM SETTING ......................................................89  
Using the Menus: Playback Mode..........................................90  
Using the Playback Menu..........................................................90  
Playback Menu Options.............................................................90  
XPHOTOBOOK ASSIST............................................................90  
bIMAGE SEARCH.......................................................................90  
xERASE.........................................................................................90  
jMARK FOR UPLOAD TO .......................................................91  
ISLIDE SHOW ............................................................................92  
The Setup Menu.............................................................................98  
Using the Setup Menu................................................................98  
Setup Menu Options...................................................................99  
F DATE/TIME ...............................................................................99  
N TIME DIFFERENCE..................................................................99  
L a.................................................................................99  
oSILENT MODE..........................................................................99  
R RESET ...................................................................................... 100  
K FORMAT ................................................................................. 100  
A IMAGE DISP. .......................................................................... 100  
B FRAME NO..............................................................................101  
G OPERATION VOL. .................................................................101  
H SHUTTER VOLUME ..............................................................101  
e SHUTTER SOUND.................................................................101  
I PLAYBACK VOLUME............................................................102  
J LCD BRIGHTNESS.................................................................102  
TMONITOR SUNLIGHT MODE............................................102  
E EVF/LCD MODE.....................................................................102  
M AUTO POWER OFF...............................................................102  
j RAW CONVERSION................................................................92 1QUICK START MODE...........................................................102  
BRED EYE REMOVAL................................................................93  
DPROTECT...................................................................................94  
GCROP ..........................................................................................94  
ORESIZE ........................................................................................95  
CIMAGE ROTATE........................................................................95  
ECOPY...........................................................................................96  
FVOICE MEMO...........................................................................96  
nERASE FACE RECOG. .............................................................97  
KPRINT ORDER (DPOF)...........................................................97  
JDISP. ASPECT ...........................................................................97  
FFn BUTTON .............................................................................102  
LDUAL IS MODE..................................................................... 103  
BRED EYE REMOVAL............................................................. 103  
C AF ILLUMINATOR ................................................................ 103  
xiii  
Table of Contents  
k AE/AF-LOCK MODE............................................................ 104  
v AE/AF-LOCK BUTTON ....................................................... 104  
j RAW ......................................................................................... 104  
IFOCUS RING.......................................................................... 104  
MFOCUS SCALE UNITS ......................................................... 104  
JCOLOR SPACE....................................................................... 105  
t SAVE ORG IMAGE................................................................ 105  
m AUTOROTATE PB ................................................................. 106  
OBACKGROUND COLOR...................................................... 106  
c GUIDANCE DISPLAY........................................................... 106  
Q VIDEO SYSTEM..................................................................... 106  
S CUSTOM RESET ................................................................... 106  
Techniiccaall NNoottees  
Optional Accessories..................................................................107  
Accessories from FUJIFILM .................................................... 108  
Caring for the Camera .............................................................. 109  
Troubleshooting  
Problems and Solutions ...........................................................110  
Warning Messages and Displays..........................................115  
Apppendix  
Internal Memory/Memory Card Capacity ........................119  
Specifications................................................................................120  
Restrictions on Camera Settings..........................................126  
Shooting Mode and Camera Settings................................126  
xiv  
Introduction  
Symbols and Conventions  
The following symbols are used in this manual:  
c: This information should be read before use to ensure correct operation.  
a: Points to note when using the camera.  
b: Additional information that may be helpful when using the camera.  
P: Other pages in this manual on which related information may be found.  
Menus and other text in the camera monitor are shown in bold. In the illustrations in this manual, the  
monitor display may be simplified for explanatory purposes.  
Supplied Accessories  
The following items are included with the camera:  
NP-95 rechargeable battery  
BC-65N battery charger  
USB cable  
Lens cap  
Owner’s Manual (this manual)  
• Shoulder strap  
Lens hood  
CD-ROM  
1
Introduction  
Parts of the Camera  
For more information, refer to the page listed to the right of each item.  
1
2
3
4
Command dial...........................23, 24, 25 9 I (continuous shooting) button...............40 18 Terminal cover.............................69, 71, 81  
Mode dial......................................................22 10 Memory card slot cover.......................12 19 Focus mode selector.............................46  
Hot shoe .............................................88, 107 11 Strap eyelet.................................................... 8 20 Focus ring .....................................................46  
AF-assist illuminator ............................103 12 Fn1 (Function 1) button...............................52 21 Zoom ring.....................................................18  
Self-timer lamp..........................................39 13 Memory card slot.....................................12 22 A/V cable connector..............................69  
Lens................................................................120 14 Flash..................................................................37 23 Connector for HDMI cable.................69  
ON/OFF switch ..............................................15 15 Microphone (L/R).....................................66 24 USB cable connector..................... 71, 81  
Shutter button...........................................19 16 N(flash pop-up) button..............................37 25 Connector for external microphone  
5
6
7
8 d(exposure compensation) button........ 44 17 Speaker...................................................68, 96  
..........................................................................107  
2
Introduction  
26 Monitor............................................................. 5 35 ISO (sensitivity) button................................49  
27 Tripod mount  
28 Battery-chamber cover........................10 36 WB (white balance) button..........................50  
29 Diopter adjustment control ................ 4 b(delete) button.........................................21  
info button....................................................61  
30 EVF/LCD (display selection) button.............. 4 37 Electronic viewfinder .............................. 4  
31 Indicator lamp............................................20 38 Eye sensor....................................................... 4  
32 a(playback) button.......................... 15, 21 39 z(movie record) button.............................66  
33 AE (autoexposure) button............................45 40 AE/AF LOCK (autofocus lock/autoexposure)  
k(playback zoom in) button.....................58  
button.....................................................35, 47  
34 AF (autofocus) button...................................48 41 Selector button (see below)  
n(playback zoom out) button ..................58 42 RAW button...................................................56  
43 DISP (display)/BACK button .................6, 20  
The Selector Button  
Move cursor up (e)  
Fn2 (Function 2) button (P52)  
MENU/OK button (P16, 83, 90, 98)  
Move cursor left (g)  
F(macro) button (P36)  
Move cursor right (h)  
N(flash) button (P37)  
Move cursor down (f)  
h(self-timer) button (P39)  
3
Introduction  
The Electronic Viewfinder (EVF)  
The electronic viewfinder provides the same information as the monitor, and can be  
used when bright lighting conditions make the display in the monitor difficult to see.  
Press EVF/LCD button to select from the auto switch, monitor, or electric view finder  
mode. When the auto switch mode is set, the electric view finder turns on automati-  
cally when you put your eye to the view finder, and the monitor turns on when you  
take your eye away (note that the eye sensor may not respond if you are wearing  
glasses or your head is an angle to the camera).  
Eye sensor  
The camera is equipped with diopter adjustment to accommodate individual dif-  
ferences in vision. Slide the diopter adjustment control up and down until the view-  
finder display is in sharp focus.  
Bright Ambient Lighting  
Reflections and glare caused by bright ambient lighting may make it hard to see the display in the monitor,  
particularly when the camera is used outdoors. This can be addressed by holding the EVF/LCD button to trigger  
outdoor mode. Outdoor mode can also be enabled using the TMONITOR SUNLIGHT MODE option in the  
setup menu (P102).  
4
Introduction  
Camera Displayys  
The following indicators may appear during shooting and playback. The indicators displayed vary with  
camera settings.  
1
2
3
4
5
6
7
8
9
Flash mode...................................................37 16 Monitor sunlight mode.....................102  
Macro (close-up) mode........................36 17 Silent mode indicator....................20, 99  
Self-timer indicator .................................39 18 Battery level.................................................15  
Continuous shooting mode .............40 19 Sensitivity..............................................49, 83  
Advanced Anti Blur.........................28, 86 20 Aperture.................................................24, 25  
White balance ............................................50 21 AE lock indicator.......................................35  
Film simulation..........................................85 22 Shutter speed.....................................24, 25  
Dynamic range..........................................85 23 Metering........................................................45  
Shooottiinngg  
Internal memory indicator*  
24 Shooting mode.........................................22  
10 Number of available frames............119 25 Manual focus indicator.........................46  
11 Image size/quality .................................. 84 26 Exposure indicator................................. 44  
12 Temperature warning....................x, 116 27 Histogram....................................................... 7  
13 Blur warning......................................38, 115 28 Focus frame.................................................34  
14 Electronic level ..........................................89 29 Focus warning ................................. 19, 115  
15 Dual IS mode ...........................................103 30 Intelligent digital zoom........................86  
* a: indicates that no memory card  
is inserted and that pictures will  
be stored in the camera’s internal  
memory (P12).  
Playback  
1
2
Favorites.........................................................57  
Intelligent Face Detection  
indicator.................................................53, 86 10 Playback mode indicator ............ 21, 57  
Red-eye removal indicator.................93 11 Portrait enhancer.....................................32  
Pro focus mode,  
8
Dynamic range..........................................85  
9 E mode..............................................27  
3
4
12 Mark for upload to...................................91  
pro low-light mode........................30, 31 13 Photobook assist......................................63  
Motion panorama z..................29, 65 14 Voice memo indicator...........................96  
Frame number........................................ 101 15 DPOF print indicator..............................72  
Gift image.....................................................57 16 Protected image.......................................94  
5
6
7
5
Introduction  
Shooting (electronic viewfinder)  
Diisppllaay Mode  
Press DISP/BACK to cycle through display modes as fol-  
lows:  
Shooting (monitor)  
STANDARD  
INFORMATION OFF  
INFO DISPLAY  
STANDARD  
CUSTOM  
Custom Display  
Choose items for display using vDISP. CUSTOM  
SETTING in the shooting menu (P89).  
CUSTOM  
INFORMATION OFF  
c
Some operations may cause the camera to exit auto-  
matically from the info to the standard display.  
6
Introduction  
Playback  
Histograms  
Histograms show the distribution of tones in the im-  
age. Brightness is shown by the horizontal axis, the  
number of pixels by the vertical axis.  
INFORMATION ON  
INFORMATION OFF  
Pixel brightness  
Shadows Highlights  
Optimal exposure: Pixels are  
distributed in an even curve  
throughout the tone range.  
Overexposed: Pixels are clustered  
at the right side of the graph.  
12/31/2050  
10:00 AM  
DETAIL  
IFAVORITES  
INFORMATION  
Underexposed: Pixels are clustered  
at the left side of the graph.  
cHighlights  
Overexposed areas blink on and  
off.  
7
Attaching Accessories  
To avoid losing the lens cap, pass the supplied string  
through the eyelet ( ) and secure the lens cap to the  
strap ( ).  
w
Thee Strap  
q
Attach the strap to the two strap eyelets as shown  
below.  
The Leennss Hood  
Rotate the lens hood in the direction shown until  
it clicks into place.  
c
To avoid dropping the camera, be sure the strap is cor-  
rectly secured.  
The Leennss Cap  
Attach the lens cap as shown.  
8
Charging the Battery  
The battery is not charged at shipment. Charge  
the battery before use.  
Plug the charger in.  
Plug the charger into an indoor power out-  
let. The charging indicator will light.  
2
3
Place the battery in the supplied battery  
charger.  
Insert the battery in the orientation indicat-  
1
The Charging Indicator  
The charging indicator shows battery charge  
status as follows:  
ed by the DFC labels.  
Charginng  
indicator  
The camera uses an NP-95 rechargeable battery.  
Batttteerryy sstaatus  
Action  
Battery not  
inserted.  
Battery fully  
charged.  
Battery  
Charge  
Insert the battery.  
Off  
Arrow  
lamp  
Remove the battery.  
Unplug the charger and  
remove the battery.  
On  
Battery charging.  
Blinks  
Battery fault.  
DFC  
label  
DFClabel  
Charge the battery.  
Battery charger  
Remove the battery when charging is  
complete. See the specifications (P124) for  
charging times (note that charging times  
increase at low temperatures).  
c
Attach the supplied adapter  
before charging the battery  
(the adapter is attached at  
shipment).  
c
Unplug the charger when it is not in use.  
Adapter  
9
Inserting the Battery  
Insert the batteries in the camera as described  
below.  
Insert the battery.  
2
Insert the battery as shown in the illustration  
inside the battery chamber, using the bat-  
tery to keep the latch pressed to one side.  
Open the battery-chamber cover.  
1
Slide the battery-cham-  
ber latch in the direction  
shown and open the bat-  
tery-chamber cover.  
Arrow  
a
Be sure the camera is off before opening the bat-  
tery-chamber cover.  
Battery latch  
c
• Do not open the battery-chamber cover when  
the camera is on. Failure to observe this pre-  
caution could result in damage to image files or  
memory cards.  
• Do not use excessive force when handling the  
battery-chamber cover.  
c
Insert the battery in the correct orientation. Do  
NOT use force or attempt to insert the battery up-  
side down or backwards. The battery will slide in  
easily in the correct orientation.  
10  
Inserting the Battery  
cBatteries  
Close the battery-chamber cover.  
Press the cover down un-  
til it clicks into place.  
3
• Remove dirt from the battery terminals with a clean,  
dry cloth. Failure to observe this precaution could  
prevent the battery from charging.  
• Do not affix stickers or other objects to the battery.  
Failure to observe this precaution could make it im-  
possible to remove the battery from the camera.  
• Do not short the battery terminals. The battery could  
overheat.  
• Read the cautions in “Power Supply and Battery”  
(Pvi).  
• Use only battery chargers designated for use with the  
battery. Failure to observe this precaution could re-  
sult in product malfunction.  
Removing the Battery  
Before removing the battery,  
turn the camera off and open  
the battery-chamber cover. To  
remove the battery, press the  
battery latch to the side, and  
slide the battery out of the cam-  
era as shown.  
• Do not remove the labels from the battery or attempt  
to split or peel the outer casing.  
• The battery gradually loses its charge when not in  
use. Charge the battery one or two days before use.  
Battery latch  
11  
Inserting a Memory Card  
c
Although the camera can store pictures in inter-  
nal memory, optional SD, SDHC and SDXC mem-  
ory cards (sold separately) can be used to store  
additional pictures.  
• Be sure card is in the correct orientation; do not  
insert at an angle or use force. If the memory  
card is not correctly inserted or no memory  
card is inserted, awill appear in the LCD moni-  
tor and internal memory will be used for record-  
ing and playback.  
Open the memory card slot cover.  
1
a
• SD/SDHC/SDXC memory  
cards can be locked, mak-  
ing it impossible to format  
Be sure the camera is off be-  
fore opening the memory  
card slot cover.  
the card or to record or  
delete images. Before in-  
serting an SD/SDHC/SDXC  
memory card, slide the  
write-protect switch to the  
unlocked position.  
Write-prroteect  
switch  
Insert the memory card.  
2
Holding the memory card in the orientation  
shown below, slide it in until it clicks into  
place at the back of the slot.  
Click  
12  
Inserting a Memory Card  
Close the memory card slot cover.  
Removing Memory Cards  
3
After confirming that the cam-  
era is off, press the card in and  
then release it slowly. The card  
can now be removed by hand.  
c
• The memory card may spring out if you remove  
your finger immediately after pushing the card in.  
• Memory cards may be warm to the touch after be-  
ing removed from the camera. This is normal and  
does not indicate a malfunction.  
13  
Inserting a Memory Card  
• miniSD or microSD adapters that are larger or smaller  
than the standard dimensions of an SD/SDHC/SDXC  
card may not eject normally; if the card does not  
eject, take the camera to an authorized service repre-  
sentative. Do not forcibly remove the card.  
Compatible Memory Cards  
FUJIFILM and SanDisk SD, SDHC, and SDXC mem-  
ory cards have been approved for use in the cam-  
era. A complete list of approved memory cards  
is available at http://www.fujifilm.com/support/  
digital_cameras/compatibility/. Operation is not  
guaranteed with other cards. The camera can not  
be used with xD-Picture Cards or MultiMediaCard  
(MMC) devices.  
• Do not affix labels to memory cards. Peeling labels  
can cause camera malfunction.  
• Movie recording may be interrupted with some types  
of SD/SDHC/SDXC memory card. Use a Gcard  
or better when shooting HD or high-speed movies.  
• The data in internal memory may be erased or cor-  
rupted when the camera is repaired. Please note that  
the repairer will be able to view pictures in internal  
memory.  
• Formatting a memory card or internal memory in the  
camera creates a folder in which pictures are stored.  
Do not rename or delete this folder or use a comput-  
er or other device to edit, delete, or rename image  
files. Always use the camera to delete pictures from  
memory cards and internal memory; before editing  
or renaming files, copy them to a computer and edit  
or rename the copies, not the originals.  
cMemory Cards  
Do not turn the camera off or remove the memory  
card while the memory card is being formatted or  
data are being recorded to or deleted from the card.  
Failure to observe this precaution could damage the  
card.  
• Format SD/SDHC/SDXC memory cards before first  
use, and be sure to reformat all memory cards af-  
ter using them in a computer or other device. For  
more information on formatting memory cards, see  
K FORMAT” (P100).  
• Memory cards are small and can be swallowed; keep  
out of reach of children. If a child swallows a memory  
card, seek medical assistance immediately.  
14  
Turning the Camera on and Off  
b Auto Power Off  
Rotate the ON/OFF switch to ON to turn the camera  
The camera will turn off automatically if no operations  
are performed for the length of time selected in the  
M AUTOPOWEROFFmenu(P102). Toreactivatethe  
camera after it has turned off automatically, turn the  
ON/OFF switch to OFF and then back to ON.  
on.  
Battery Level  
Battery level is shown as follows:  
Select OFF to turn the camera off.  
Indicator  
Description  
D(white) Battery partially discharged.  
b Switching to Playback Mode  
Press the abutton to start playback. Press abutton  
again or press the shutter button halfway to return to  
shooting mode.  
C(white) Battery more than half discharged.  
Low battery. Charge as soon as pos-  
B(red)  
sible.  
Battery exhausted. Turn camera off  
and charge battery.  
A(blinks red)  
15  
Basic Setup  
A language-selection dialog is displayed the first time the camera is turned on. Set up the camera as  
described below (for information on resetting the clock or changing languages, see page 99).  
Highlight a language and press MENU/OK.  
1
ENGLISH  
FRANCAIS  
DEUTSCH  
ESPAÑOL  
PORTUGUÊS  
a
Press DISP/BACK to skip the current step. Any steps you skip will be displayed  
the next time the camera is turned on.  
The date and time will be displayed. Press the selector left or right to  
highlight the year, month, day, hour, or minute and press up or down  
to change. To change the order in which the year, month, and day  
are displayed, highlight the date format and press the selector up or  
down. Press MENU/OK when settings are complete.  
DATE / TIME NOT SET  
2
2013  
2012  
YY. MM. DD  
2011 1.  
2009  
1
12:00  
AM  
2010  
SET  
NO  
b The Camera Clock  
If the battery is removed for an extended period, the camera clock will be reset and the language-selection dialog  
will be displayed when the camera is turned on.  
16  
Taking Pictures  
This section explains basic photography.  
Select a mode.  
1
When you rotate the mode dial to EXR, the R display will appear in the LCD monitor.  
Scene Icon (P27)  
The camera automatically selects the appropriate scene.  
The oIcon  
In R mode, the camera continuously adjusts focus and searches for faces, increasing the drain on the  
battery. ois displayed in the LCD monitor.  
a
• The camera analyses the scene and selects the preferred E mode when the shutter button is pressed  
halfway (P28).  
• To raise the flash when lighting is poor, press the flash pop-up button (P37).  
17  
Taking Pictures  
Frame the picture.  
Holding the Camera  
2
Use the zoom ring to  
frame the picture in the  
display. The zoom indica-  
tor appears.  
Hold the camera steady with  
both hands and brace your  
elbows against your sides.  
Shaking or unsteady hands  
can blur your shots.  
Zoom ring  
To prevent pictures that are  
out of focus or too dark (un-  
derexposed), keep your fin-  
gers and other objects away  
from the lens and flash.  
Zoom indicator  
b Focus Lock  
Use focus lock (P34) to focus on subjects that are not  
in the focus frame.  
18  
Taking Pictures  
b The Shutter Button  
The shutter button has two positions. Pressing the  
Focus.  
3
4
Press the shutter button halfway  
to focus.  
shutter button halfway ( ) sets focus and exposure;  
q
to shoot, press the shutter button the rest of the way  
down ( ).  
w
If the camera is able to focus, it will beep twice  
and the indicator lamp will glow green.  
Double  
beep  
Click  
If the camera is unable to focus, the focus frame  
will turn red, swill be displayed, and the  
indicator lamp will blink green. Change the  
composition or use focus lock (P34).  
q
w
Press halfway  
Press the rest of  
the way down  
Shoot.  
Smoothly press the shutter button  
the rest of the way down to take  
the picture.  
a
If the subject is poorly lit, the AF-assist illuminator may  
lighttoassistfocus(P103). Forinformationonusingthe  
flash when lighting is poor, see page 37.  
19  
Taking Pictures  
Silent Mode  
The Indicator Lamp  
In situations in which camera sounds or lights may be  
unwelcome, hold the DISP/BACK button down until o  
is displayed.  
Indicator lamp  
The indicator lamp shows camera status as follows:  
Indiicattor lamp Camera staattuuss  
Glows green Focus locked.  
Blur, focus, or exposure warning. Pic-  
ture can be taken.  
Blinks green Recording pictures. Additional pic-  
and orange tures can be taken.  
Blinks green  
The camera speaker, flash, and AF-assist illuminator/  
self-timer lamp turn off and flash and volume settings  
can not be adjusted (note that the flash will still fire  
when Cis selected in scene mode). To restore nor-  
mal operation, press the DISP/BACK button until the o  
icon is no longer displayed.  
Glows  
orange  
Recording pictures. No additional pic-  
tures can be taken at this time.  
Flash charging; flash will not fire when  
picture is taken.  
Blinks orange  
Lens or memory error (memory card  
Blinks red full or not formatted, format error, or  
other memory error).  
b Warnings  
Detailed warnings appear in the display. See pages  
115–118 for more information.  
20  
Viewing Pictures  
Pictures can be viewed in the monitor. When taking important photographs, take a test shot and  
check the results.  
Press the abutton.  
Deleting Pictures  
To delete the picture currently displayed in the moni-  
tor, press the bbutton.  
1
The most recent picture will be displayed in  
the monitor.  
To exit without deleting the picture, highlight CAN-  
CEL and press MENU/OK.  
b The Playback Menu  
Pictures can also be deleted from the playback menu  
(P60).  
View additional pictures.  
2
Press the selector right to view  
pictures in the order recorded, left  
to view pictures in reverse order.  
Press the shutter button to exit to shooting  
mode.  
21  
Shooting Mode  
Choose a shooting mode according to the scene or type of subject. To  
choose a shooting mode, rotate the mode dial to the desired setting. The  
following modes are available:  
P, S, A, M: Select for full control over camera settings, including  
aperture (M and A) and/or shutter speed (M and S) (P23).  
EXR: Improve clarity, reduce noise, in-  
crease dynamic range, or let the camera  
automatically adjust settings to suit the  
scene (P27).  
C1/C2/C3 (CUSTOM): Recall stored set-  
tings for modes P, S, A, M and all EXR  
modes except R (P26).  
B
(AUTO):  
A
simple “point-and-shoot”  
mode recommended for first-time users  
of digital cameras (P28).  
Adv. (ADVANCED): Sophisticated tech-  
niques made easy (P28).  
SP (SCENE POSITION): Choose a scene suited to the subject or  
shooting conditions and let the camera do the rest (P32).  
22  
Shooting Mode  
P: PROGRAM AE  
Program Shift  
Rotate the command dial to choose the desired com-  
bination of shutter speed and aperture. The default  
values can be restored by raising the flash or turning  
the camera off. To use program shift, turn the flash  
off and select OFF for gEXTERNAL FLASH. Fur-  
thermore, an option other than AUTO must be se-  
lected for UDYNAMIC RANGE and NISO.  
In this mode, the camera sets exposure  
automatically. If desired, you can choose  
different combinations of shutter speed  
and aperture that will produce the same  
exposure (program shift).  
c
If the subject is outside the metering range of the cam-  
era, the shutter speed and aperture displays will show  
“---”. Press the shutter button halfway to measure ex-  
posure again.  
Shutter speed  
Aperture  
23  
Shooting Mode  
S: SHUTTER PRIORITY AE  
Choose the shutter speed using the  
command dial, while the camera ad-  
justs aperture for optimal exposure.  
A: APERTURE PRIORITY AE  
Choose the aperture using the com-  
mand dial, while the camera adjusts  
shutter speed for optimal exposure.  
Shutter speed  
Aperture  
c
c
• If the correct exposure can not be achieved at the  
selected shutter speed, aperture will be displayed in  
red. Adjust shutter speed until the correct exposure  
is achieved. If the subject is outside the metering  
range of the camera, the aperture display will show  
“F---”. Press the shutter button halfway to measure  
exposure again.  
If the correct exposure can not be achieved at the se-  
lected aperture, shutter speed will be displayed in red.  
Adjust aperture until the correct exposure is achieved.  
If the subject is outside the metering range of the cam-  
era, the shutter speed display will show “---”. Press the  
shutter button halfway to measure exposure again.  
• The shutter speed is restricted depending on the ISO  
setting.  
24  
Shooting Mode  
M: MANUAL  
The Exposure Indicator  
In this mode, you choose both shutter  
speed and aperture. If desired, expo-  
sure can be altered from the value sug-  
gested by the camera.  
The amount the picture will  
be under- or over-exposed at  
current settings is shown by  
the exposure indicator.  
Press the dbutton to choose between shutter  
speed and aperture and rotate the command dial  
to adjust the selected setting.  
Shutter speed  
Aperture  
c
• Noise in the form of randomly-spaced bright pixels  
may occur in long exposures.  
• The shutter speed is restricted depending on the ISO  
setting.  
25  
Shooting Mode  
Meenu/settiing  
Settinggs saved  
C1/C2/C3: CUSTOM MODE  
NISO, OIMAGE SIZE, TIMAGE QUAL-  
ITY, UDYNAMIC RANGE, PFILM SIMULA-  
TION, dWB SHIFT, fCOLOR, HSHARP-  
NESS, rHIGHLIGHT TONE, sSHADOW  
TONE, hNOISE REDUCTION, RINTELLI-  
GENT DIGITAL ZOOM, bFACE DETECTION,  
nFACE RECOGNITION, FAF MODE,  
IFLASH, gEXTERNAL FLASH, WMOVIE  
MODE, a STILL SHOOTING IN MOVIE  
In P, S, A, M and all EXR modes except  
R, the KCUSTOM SET option in  
the shooting menu (P89) can be used  
to save current camera and menu set-  
tings. These settings are recalled when-  
ever the mode dial is rotated to C1/C2/  
C3 (custom mode).  
Shooting  
menu  
Setupp menu C AF ILLUMINATOR, j RAW  
Exposure compensation (d), metering (AE),  
white balance (WB), burst/bracketing mode  
(I), macro mode (F), flash mode (N), program  
shift, shutter speed, aperture, monitor display  
options (DISP/BACK)  
Other  
c
Once the camera is turned off, RINTELLIGENT DIGI-  
TAL ZOOM is deactivated.  
26  
Shooting Mode  
EXR (E AUTO/E Priority)  
Optimize settings for your current subject or improve clarity, reduce noise, or enhance dy-  
namic range. Rotate the mode dial to EXR and choose one of the following E modes  
in the shooting menu.  
R(EAUTO)  
The camera automatically selects the scene and E mode according to shooting conditions.  
a
If S is selected for OIMAGE SIZE in R mode, the camera will automatically select the optimal image size.  
The Scene Icon  
The camera selects from the following scenes:  
LAND-  
SCAPE  
SKY &  
GREENERY  
Scene  
AUTO  
NIGHT  
MACRO  
BEACH  
SUNSET  
SNOOW  
SKY  
GREENERY  
Main subject  
Nonn-porrtraait  
a
d
g
c
a
b
c
d*  
dd*  
e
u
v
w
x
y
z
Normal  
Backlit  
dc  
gc  
cc  
ac  
bc  
du  
gu  
cu  
au  
bu  
dv  
gv  
cv  
av  
bv  
dw  
gw  
cw  
aw  
bw  
dx  
gx  
cx  
ax  
bx  
dy  
gy  
cy  
ay  
by  
dz  
gz  
cz  
az  
bz  
Portrait  
ce  
Movving oobbject  
Portrait aand motion  
cd  
ad  
Normal  
Backlit  
* If nis displayed, the camera will take a series of shots (advanced anti-blur; P28).  
c
The mode selected may vary with shooting conditions. If the mode and subject do not match, select Bmode  
(P28) or choose SP (P32) and select a scene manually.  
27  
Shooting Mode  
EPriority  
Advanced Anti Blur  
Select this mode to manually choose from the fol-  
lowing E modes:  
S (RESOLUTION PRIORITY): Choose for crisp, clear  
shots.  
T (HIGH ISO & LOW NOISE): Reduce noise in pic-  
tures taken at high sensitivities.  
When nis displayed, the camera will take a series of  
exposures and combine them to form a single image,  
reducing “noise” (mottling) and blur.  
a
n is available when ON is selected in the shooting  
menu (P86) and the flash (P37) is off or set to auto.  
U (D-RANGE PRIORITY): Increase the amount of  
detail visible in highlights.  
UDYNAMIC RANGE (P85) can be set to M  
(1600%) and D (800%).  
c
• Some time may be required to combine the expo-  
sures into a single image. A single combined image  
may not be created if the subject or camera moves  
during shooting. Keep the camera steady during  
shooting and do not move the camera until shoot-  
ing is complete.  
BAUTO  
Choose for crisp, clear snapshots. This  
mode is recommended in most situa-  
tions.  
• Frame coverage is reduced.  
The EXR Icon  
When the shutter button is pressed halfway, the  
camera chooses the preferred E mode:  
S (RESOLUTION PRIORITY): Produces crisp, clear  
shots.  
T (HIGH ISO & LOW NOISE): Reduces noise in pic-  
tures taken at high sensitivities.  
Adv. ADVANCED  
This mode combines “point-and-shoot”  
simplicity with sophisticated photograph-  
ic techniques. The  
A
Adv. MODE op-  
tion in the shooting menu can be used  
to choose from the following advanced  
modes:  
U (D-RANGE PRIORITY): Increases the amount of  
detail visible in highlights.  
28  
Shooting Mode  
a
rMOTION PANORAMA 36600  
Follow an on-screen guide  
to take photos that will  
automatically be joined to  
form a panorama.  
Shooting ends if the shutter button is pressed all the  
way down during shooting. No panorama will be re-  
corded if the shutter button is pressed before the cam-  
era has been panned through 120°.  
c
• Panoramas are created from multiple frames. The  
camera may in some cases record a greater or lesser  
angle than selected or be unable to stitch the frames  
together perfectly. The last part of the panorama  
may not be recorded if shooting ends before the  
panorama is complete.  
• Shooting may be interrupted if the camera is panned  
too quickly or too slowly. Panning the camera in a  
direction other than that shown cancels shooting.  
• The desired results may not be achieved with mov-  
ing subjects, subjects close to the camera, unvarying  
subjects such as the sky or a field of grass, subjects  
that are in constant motion, such as waves and wa-  
terfalls, or subjects that undergo marked changes in  
brightness. Panoramas may be blurred if the subject  
is poorly lit.  
Rotate the zoom ring until the zoom indicator  
turns white (P18).  
1
To select the angle through which you will pan  
2
the camera while shooting, press the selector  
down. Press the selector left or right to high-  
light an angle and press MENU/OK.  
Press the selector right to view a choice of pan  
directions. Press the selector left or right to  
highlight a pan direction and press MENU/OK.  
3
Press the shutter button all the way down to  
start recording. There is no need to keep the  
shutter button pressed during recording.  
4
Pan the camera in the di-  
120  
5
rection shown by the arrow.  
Shooting ends automati-  
cally when the progress bar  
is full and the panorama is  
Progress bar  
complete.  
29  
Shooting Mode  
iPRO FOCUS  
z
Choose zfor seamless 360 ° panoramas that can be  
played back in a loop (P65).  
The camera takes up to three  
shots each time the shutter  
button is pressed, softening  
the background to emphasize  
the main subject. The amount  
of softening can be adjusted before shooting by  
rotating the command dial. Use for portraits or  
photos of flowers similar to those produced by  
SLR cameras.  
a
The t SAVE ORG IMAGE option in the setup menu  
can be used to record a vpanorama in addition to  
a seamless zpanorama (P105).  
c
Depending on the subject and shooting conditions,  
the camera may produce distorted results or a v  
panorama. The top and bottom of the area visible in  
the shooting display are cropped out and white strips  
may appear at the top and bottom of the display.  
a
Softening can not be applied to background objects  
that are too close to the main subject. If a message  
stating that the camera can not create the effect is  
displayed when the camera focuses, try backing away  
from your subject and zooming in. The camera may  
also be unable to soften the background if the subject  
is moving; if prompted, check the results and try again.  
For Best Results  
For best results, move the camera in a small circle at  
a steady speed, keeping the camera horizontal and  
being careful only to pan in the direction shown by  
the guides. If the desired results are not achieved, try  
panning at a different speed.  
30  
Shooting Mode  
jPRO LOW-LIGHT  
Pro Focus/Pro Low-Light  
Each time the shutter button  
is pressed, the camera makes  
four exposures and combines  
them into a single photograph.  
Use to reduce noise and blur  
when photographing poorly lit subjects or static  
subjects at high zoom ratios.  
To save unprocessed copies of pictures taken in these  
modes, select ON for the t SAVE ORG IMAGE op-  
tion in the setup menu (P105).  
c
• Keep the camera steady during shooting.  
• Frame coverage is reduced.  
a
• A single combined photograph may not be created  
with some scenes or if the subject or camera moves  
during shooting. Do not move the camera until  
shooting is complete.  
• The camera may make fewer than four exposures in  
some situations.  
31  
Shooting Mode  
SP SCENE POSITION  
The camera offers a choice of “scenes,” each adapted to particular shooting conditions or  
a specific type of subject. Use the ASCENE POSITION option in the shooting menu to  
choose the scene assigned to the SP position on the mode dial.  
Scene  
CNATURAL & N  
DNATURAL LIGHT  
L PORTRAIT  
Description  
The camera takes two shots: one without the flash and one with.  
Capture natural lighting under low-light conditions.  
Choose for portraits.  
Z PORTRAIT ENHANCER Choose for a smooth skin effect when shooting portraits.  
l DOG  
Choose when photographing dogs.  
mCAT  
Choose when photographing cats.  
M LANDSCAPE  
N SPORT  
Choose for daylight shots of buildings and landscapes.  
Choose when photographing moving subjects.  
O NIGHT  
Choose this mode for poorly lit twilight or night scenes.  
Choose this mode for slow shutter speeds when shooting at night.  
Slow shutter speeds are used to capture the expanding burst of light from a firework.  
Choose this mode to record the vivid colors in sunrises and sunsets.  
Choose for crisp, clear shots that capture the brightness of scenes dominated by shining white snow.  
Choose for crisp, clear shots that capture the brightness of sunlit beaches.  
Capture indoor background lighting under low-light conditions.  
Choose for vivid close-ups of flowers.  
HNIGHT (TRIPOD)  
UFIREWORKS  
QSUNSET  
RSNOW  
VBEACH  
U PARTY  
V FLOWER  
WTEXT  
Take clear pictures of text or drawings in print.  
32  
Shooting Mode  
l DOG/mCAT  
The camera focuses on the faces of dogs or cats that are facing the camera, and the self-timer menu offers a  
nAUTO RELEASE option that releases the shutter automatically when a pet is detected (P39). During play-  
back, image search (P62) can be used to search for pictures taken in either mode.  
1
Although camera can detect many different breeds of dogs and cats, results may vary with the breed and shoot-  
ing conditions. The camera may fail to detect pets with dark-colored faces or long hair covering their entire face.  
If a dog or cat is not detected, the camera focuses on the subject at the center of the frame.  
33  
Focus Lock  
To compose photographs with off-center subjects:  
Position the subject in the focus frame.  
Autofocus  
1
2
Although the camera boasts a high-precision autofo-  
cus system, it may be unable to focus on the subjects  
listed below. If the camera is unable to focus using  
autofocus, use focus lock to focus on another subject  
at the same distance and then recompose the pho-  
tograph.  
• Very shiny subjects such as mirrors or car bodies.  
• Fast-moving subjects.  
• Subjects photographed through a window or other  
reflective object.  
Focus.  
Press the shutter button  
halfway to set focus and  
exposure. Focus and ex-  
posure will remain locked  
while the shutter button  
is pressed halfway (AF/AE  
1000 F3.3  
lock).  
• Dark subjects and subjects that absorb rather than  
reflect light, such as hair or fur.  
• Insubstantial subjects, such as smoke or flame.  
• Subjects that show little contrast with the back-  
ground (for example, subjects in clothing that is the  
same color as the background).  
Recompose the picture.  
3
Keeping the shutter but-  
ton pressed halfway, re-  
compose the picture.  
• Subjects positioned in front of or behind a high-  
contrast object that is also in the focus frame (for  
example, a subject photographed against a back-  
drop of highly contrasting elements).  
1000 F3.3  
Shoot.  
4
34  
The AE/AF LOCK Button  
The AE/AF LOCK button can be used to lock exposure or focus.  
Lockingg EExxppoossuure  
Recompose the picture.  
Keeping the shutter button pressed halfway,  
recompose the picture.  
3
Meter exposure.  
1
Position the subject in the focus frame and  
press the AE/AF LOCK button to meter expo-  
sure.  
c
Adjusting zoom ends AE lock. AE lock is not avail-  
able with Intelligent Face Detection.  
Shoot.  
4
Lockiing Focus  
Focus.  
Keeping the AE/AF LOCK  
2
If AF LOCK ONLY is selected for v AE/AF-LOCK  
BUTTON in the setup menu (P104), pressing the  
AE/AF LOCK button locks focus. If AE/AF LOCK is  
selected, both focus and exposure will be locked.  
+
button pressed, press the  
shutter button halfway  
to focus. Focus and ex-  
posure will remain locked while the shutter  
button is pressed halfway, even if you later  
release the AE/AF LOCK button.  
a
If AE&AF ON/OFF SWITCH is selected for k AE/AF-  
LOCKMODEinthesetupmenu(P104), exposure and/  
or focus will lock when the AE/AF LOCK button is pressed  
and remain locked until the button is pressed again.  
Repeat steps 1 and 2 as desired to refocus  
before taking the picture.  
35  
FMacro and Super Macro Modes (Close-ups)  
For close-ups, press the selector left (F) to choose from the macro options shown below.  
Choose from F(macro mode),  
G(super macro mode), or  
OFF (macro mode off)  
When macro mode is in effect, the camera focuses on subjects near the center of the frame. Use the  
zoom ring to compose pictures. The following restrictions apply in super macro mode: the lens must  
be zoomed all the way out (at other zoom positions, zis displayed) and the flash can not be used.  
a
• Use of a tripod is recommended to prevent blur caused by camera shake.  
• Flash compensation may be required when using the flash (P88).  
• Using the flash at close range may cast a lens shadow. Zoom a little or have more distance from the subject.  
• The camera can focus at short range when macro mode is not set, but the time needed to focus increases.  
• Rotate the zoom ring until the zoom indicator turns white when using G(P18).  
Focus Range (distance from front of lens)  
Macro: approx. 7cm–3m/0.2ft.–9.8ft. (wide angle); 2m–3.5m/6.5ft.11.4ft. (telephoto)  
Super macro: approx. 1cm–1m/0.3in.–3.2ft. (wide angle)  
36  
NUsing the Flash (Super-Intelligent Flash)  
When the flash is used, the camera’s Super-Intelligent Flash system instantly analyzes the scene based  
on such factors as the brightness of the subject, its position in the frame, and its distance from the  
camera. Flash output and sensitivity are adjusted to ensure that the main subject is correctly exposed  
while preserving the effects of ambient background lighting, even in dimly-lit indoor scenes. Use the  
flash when lighting is poor, for example when shooting at night or indoors under low light.  
Raise the flash.  
Press the flash pop-up button to raise the flash.  
1
Choose a flash mode.  
Press the selector right (N). The flash mode changes each time the selector is pressed.  
2
Mode  
A/K  
(AUTO FLASH)  
Description  
The flash fires when required. Recommended in most situations.  
N/L  
The flash fires whenever a picture is taken. Use for backlit subjects or for natural  
(FORCED FLASH) coloration when shooting in bright light.  
O/M  
Capture both the main subject and the background under low light (note that  
(SLOW SYNCHRO) brightly lit scenes may be overexposed).  
37  
NUsing the Flash (Super-Intelligent Flash)  
c
The flash may fire several times with each shot. Do not move the camera until shooting is complete.  
a
• The peripheral part of an image may be dark when using the flash.  
• Remove lens hoods to prevent shadows in photos taken with the flash.  
Red-Eye Removal  
When Intelligent Face Detection is active (P53), and ON is selected for BRED EYE REMOVAL in the  
setup menu (P103), red-eye removal is available in K, L, and M.  
Red-eye removal minimizes “red-eye” caused when light from the flash is reflected from the subject’s  
retinas as shown in the illustration at right.  
Turning the Flash Off  
Lower the flash where flash photography is prohibited or to capture natural lighting un-  
der dim light. At slow shutter speeds, kwill be displayed to warn that pictures may be  
blurred; use of a tripod is recommended.  
Optional Flash Units  
The camera can be used with optional EF-42 and EF-20 clip flash units (P107).  
38  
JUsing the Self-Timer  
To use the self-timer, press the selector down (h) and choose from the following options:  
Option  
T(OFF)  
Description  
Self-timer off.  
The shutter is released ten seconds after the shutter button is pressed. Use for self-portraits.  
The self-timer lamp on the front of the camera lights when the timer starts and begins to  
blink shortly before the photo is taken.  
S(10 SEC)  
The shutter is released two seconds after the shutter button is pressed. Use to reduce blur  
caused by the camera moving when the shutter button is pressed. The self-timer lamp will  
blink as the timer counts down.  
R(2 SEC)  
Burst Mode  
If I is selected for burst mode (P40), the camera will record burst of five photographs when the timer expires,  
improving your chances of getting the desired results in portraits taken with the self-timer.  
39  
Continuous Shooting (Burst Mode/Bracketing)  
Capture motion or automatically vary selected settings over a series of pictures.  
a
• Focus and exposure are determined by the first frame  
in each series. The flash turns off automatically; the  
previously-selected flash mode is restored when con-  
tinuous shooting is turned off.  
Press the I button and choose  
from the following options:  
B: STILL IMAGE  
I: TOP  
• Frame rate varies with shutter speed.  
• The number of pictures that can be taken in a single  
burst varies with the scene and camera settings. The  
number of pictures that can be recorded depends on  
the memory available.  
• If P is selected in I or P, pictures will be recorded  
at size P or smaller.  
P: BEST FRAME CAPTURE  
O: AE BKT  
W: ISO BKT  
X: FILM SIMULATION BKT  
Y: DYNAMIC RANGE BKT  
• If you select 16 frames in P, pictures will be recorded  
at size P or smaller.  
40  
Continuous Shooting (Burst Mode/Bracketing)  
ITOP n  
PBEST FRAMEE CCAAPTURE  
The camera takes photographs while the shutter The camera takes a series of pictures, starting  
button is pressed.  
before and ending after the shutter button is  
pressed. To choose the frame rate and number  
of shots:  
Press the selector right or left to choose the  
frame rate.  
1
Press the selector right when the camera is in  
shooting mode.  
Option  
P
Max frame rate  
10 fps  
1
J
7 fps  
5 fps  
3 fps  
Highlight the current frame rate and press the  
K
2
selector right, then press selector up or down  
to choose a new value and press MENU/OK to  
select.  
O
The frame rate varies depending on the shoot-  
ing conditions or numbers of frames in con-  
tinuous shooting.  
c
Some frame rates may reduce the number of shots  
available in Step 3.  
Press MENU/OK to return to shooting mode  
when settings are complete.  
2
41  
Continuous Shooting (Burst Mode/Bracketing)  
Highlight the number of  
shots and press the selec-  
tor right. Press the selector  
up or down to choose the  
number of shots in each  
burst and left or right to  
choose their distribution  
(the number on the left is taken before and the  
number on the right after the shutter button  
is pressed). Press MENU/OK when settings are  
complete.  
Take photographs. The camera begins record-  
ing while the shutter button is pressed half-  
way, and completes the burst when the shut-  
ter button is pressed all the way down. The  
illustration shows a burst of eight shots, three  
before the shutter button is pressed and four  
after.  
Shots per burst  
3
4
5
Distribution  
Shutter button  
pressed all the  
way down  
Shutter button  
pressed halfway  
Press DISP/BACK to return to shooting mode.  
“Before” “After”  
shots shots  
c
• If the shutter button is pressed all the way down be-  
fore the number of frames selected for the “before”  
portion is recorded, the remaining frames will be  
taken after the shutter button is pressed all the way  
down.  
• If the shutter button is pressed halfway for an extend-  
ed period, the camera may record the burst before  
the shutter button is pressed all the way down.  
42  
Continuous Shooting (Burst Mode/Bracketing)  
OAE BKT  
XFILMM SSIMMUULATIION BKT  
Press the selector left or right to highlight a Each time the shutter button is pressed, the cam-  
bracketing amount. Each time the shutter but- era takes one shot and processes it to create three  
ton is pressed, the camera will take three shots: copies with different PFILM SIMULATION set-  
one using the metered value for exposure, the tings(P85):c PROVIA/STANDARDforthefirst,  
second overexposed by the selected amount, d Velvia/VIVID for the second, and e ASTIA/  
and the third underexposed by the same amount SOFT for the third.  
(the camera may not be able to use the selected  
YDYNAMIC RRANGGE BKT  
bracketing increment if the amount of over- or  
Each time the shutter button is pressed, the cam-  
under- exposure exceeds the limits of the expo-  
era takes three shots at different UDYNAMIC  
sure metering system).  
RANGE settings (P85): A 100% for the first,  
WISO BKT  
B 200% for the second, and C 400% for  
Press the selector left or right to highlight a brack- the third (NISO can not exceed 3200; values less  
eting amount. Each time the shutter is released, than 400 are not available when O is selected for  
the camera will take a picture at the current sensi- OIMAGE SIZE).  
tivity(P83)andprocessittocreatetwoadditional  
copies, one with sensitivity raised and the other  
with sensitivity lowered by the selected amount  
(regardless of the amount selected, sensitivity will  
not exceed ISO 800 or fall below ISO 200).  
43  
dExposure Compensation  
Use exposure compensation when photographing very bright, very dark, or high-contrast subjects.  
Press the dbutton and rotate  
the command dial until the  
exposure indicator shows the  
desired value.  
The effect is visible in the display.  
Choose negative values Choose positive values to  
Exposure indicator  
to reduce exposure  
increase exposure  
1
• A d icon and exposure indicator are displayed at  
settings other than 0. Exposure compensation is  
not reset when the camera is turned off; to restore  
normal exposure control, choose a value of 0.  
• Turn the flash off when using exposure compensa-  
tion.  
44  
Metering  
To choose how the camera meters exposure, press the AE button and then choose from the following  
options.  
Option  
o
Description  
Automatic scene recognition is used to adjust exposure for a wide range of shooting conditions.  
(MULTI)  
p
The camera meters lighting conditions at the center of the frame. Recommended when the back-  
(SPOT) ground is much brighter or darker than the main subject.  
Exposure is set to the average for the entire frame. Provides consistent exposure across multiple  
shots with the same lighting, and is particularly effective for landscapes and portraits of subjects  
dressed in black or white.  
q
(AVERAGE)  
45  
Focus Mode  
Use the focus mode selector to choose how the camera focuses.  
The following options are available:  
Mode  
Description  
AF-S  
(SINGLE AF)  
Focus locks while the shutter button is pressed halfway. Choose for stationary subjects.  
The camera continually adjusts focus to reflect changes in the distance to the subject even  
when the shutter button is not pressed halfway (note that this increases the drain on the  
battery). Choose for moving subjects.  
AF-C  
(CONTINUOUS AF)  
Focus manually using focus ring. Rotate focus ring left to reduce the focus distance, right to  
increase. Choose for manual control of focus or in situations in which the camera is unable to  
focus using autofocus (P34). Intelligent Face Detection turns off automatically.  
MF  
Reduce focus  
distance  
Increase focus  
distance  
(MANUAL FOCUS)  
Manual focus mode icon  
a
Focus-mode selection is also available during movie recording.  
46  
Focus Mode  
b Manual Focus  
• Use of a tripod is recommended. Focus may be affected if the camera moves.  
• Use the IFOCUS RING option in the setup menu (P104) to reverse the direction of rotation for the focus ring.  
• The camera may not focus if the focus ring is over-rotated. Rotate the focus ring in the opposite direction to  
restore focus.  
• To focus using autofocus, press the AE/AF LOCK button. This can be used to quickly focus  
on a chosen subject in manual focus mode.  
Checking Focus (Manual Focus)  
At default settings (P52), the Fn2 button can be used to zoom in on the view through the lens and  
check focus.  
b Scrolling The Focus Check Area  
Press the AF button and then press the selector up, down, left or right to scroll the focus  
check area (returned to the center by pressing MENU/OK). The setting takes effect when you  
press the AF button again.  
47  
Focus Frame Selection  
When tAREA is selected for FAF MODE in When framing a picture in the LCD monitor, you  
the shooting menu and AF-S is selected for focus can choose the size of the focus frame for AF-S.  
mode, focus position can be changed. Press AF Press the AF button and then rotate the command  
button and then press the selector up, down, left dial. The frame size can be reduced up to 50%  
or right (the focus frame can be returned to the or enlarged up to 150%. The setting takes effect  
center by pressing MENU/OK). The setting takes ef- when you press the AF button again.  
fect when you press the AF button again.  
Focus point  
Focus frame  
48  
Sensitivity  
The camera’s sensitivity to light can be adjusted by pressing the ISO button  
and then rotating the command dial until the desired value is highlighted  
in the display.  
ISO  
Higher values can reduce blur; note, however, that mottling may appear in pictures taken at high sensitivities.  
100  
12800  
ISO  
Bright  
Dark  
Scene  
Less noticeable  
More noticeable  
Noise (mottling)  
Option  
Description  
Sensitivity is adjusted automatically in response to shooting conditions.  
AUTO (3200) / AUTO (1600) / AUTO (800) / As above, except that sensitivity will not be raised above the value in paren-  
AUTO  
AUTO (400)  
theses.  
12800 / 6400 / 5000 / 4000 / 3200 / 2500 /  
2000 / 1600 / 1250 / 1000 / 800 / 640 /  
500 / 400 / 320 / 250 / 200 / 100  
Sensitivity is set to the specified value, which is shown in the display.  
a
Sensitivity can also be adjusted in the shooting menu (P83).  
49  
White Balance  
For natural colors, press the WB button and choose a setting that matches  
the light source.  
Option  
AUTO  
h
k
i
Description  
White balance adjusted automatically.  
Measure a value for white balance.  
Selecting this option displays a list of color temperatures (P51); highlight a temperature and press MENU/OK.  
For subjects in direct sunlight.  
j
For subjects in the shade.  
k
Use under “daylight” fluorescent lights.  
l
Use under “warm white” fluorescent lights.  
Use under “cool white” fluorescent lights.  
m
n
Use under incandescent lighting.  
h: Custom White Balance  
Choose h to adjust white balance for unusual lighting conditions. White balance measurement options will  
be displayed; frame a white object so that it fills the LCD monitor and press the shutter button all the way down  
to measure white balance.  
If “COMPLETED!” is displayed, press MENU/OK to set white balance to the measured value.  
If “UNDER” is displayed, raise exposure compensation (P44) and try again.  
If “OVER” is displayed, lower exposure compensation and try again.  
a
For greater precision, adjust PFILM SIMULATION, NISO, and UDYNAMIC RANGE before measuring  
white balance.  
50  
White Balance  
a
• White balance is adjusted for flash lighting only in AUTO mode. Turn the flash off when using other white balance  
options.  
• Results vary with shooting conditions. Play pictures back after shooting to check colors in the LCD monitor.  
k: Color Temperature  
Color temperature is an objective measure of the color of a light source, expressed in Kelvin (K). Light sources  
with a color temperature close to that of direct sunlight appear white; light sources with a lower color tempera-  
ture have a yellow or red cast, while those with a higher color temperature are tinged with blue. You can match  
color temperature to the light source as shown in the following table, or choose options that differ sharply from  
the color of the light source to make pictures “warmer” or “colder”.  
Choose for redder light sources  
or “colder” pictures  
Choose for bluer light sources  
or “warmer” pictures  
15,000 K  
Blue sky  
2,000 K  
Candlelight  
Sunset/sunrise  
5,000 K  
Direct sunlight  
Shade  
51  
The Fn Button  
The role played by the Fn1/Fn2 button can be selected using the FFn  
BUTTON option in the setup menu (P102).  
The following options are available:  
IMAGESIZE( P84)/IMAGEQUALITY( P84)/DYNAMICRANGE( P85)/FILMSIMULATION  
(P85)/AFMODE( P87)/FACEDETECTION( P86)/FACERECOGNITION( P87)/INTELLIGENT  
DIGITAL ZOOM (P86)/Focus Check (P47).  
Fn1 button  
Fn2 button  
a
The FFn BUTTON menu can also be displayed by pressing and holding the Fn1/Fn2 button.  
52  
bIntelligent Face Detection  
Intelligent Face Detection allows the camera to automatically detect human faces and set focus and  
exposure for a face anywhere in the frame for shots that emphasize portrait subjects. Choose for group  
portraits (in horizontal or vertical orientations) to prevent the camera from focusing on the background.  
To use Intelligent Face Detec-  
tion, press MENU/OK to display  
the shooting menu and se-  
lect ON for bFACE DETEC-  
TION. Faces can be detected  
with the camera in vertical  
or horizontal orientation; if a  
face is detected, it will be indicated by a green bor-  
der. If there is more than one face in the frame, the  
camera will select the face closest to the center;  
other faces are indicated by white borders.  
Intelligent Face Detection  
Intelligent Face Detection is  
recommended when using  
the self-timer for group- or  
self-portraits (P39).  
7
Green border  
When a picture taken with Intelligent Face Detection  
is displayed, the camera can automatically select faces  
forred-eyeremoval(P93),playbackzoom(P58),slide  
shows(P92),imagesearch(P62),imagedisp.(P100),  
printing (P75), and cropping (P94).  
c
• In some modes, the camera may set exposure for the  
frame as a whole rather than the portrait subject.  
• If the subject moves as the shutter button is pressed,  
their face may not be in the area indicated by the  
green border when the picture is taken.  
53  
nFace Recognition  
The camera can store information on the face  
and personal details (name, relationship, and  
birth date) of portrait subjects and assign these  
subjects priority for Intelligent Face Detection or  
display their names and other information during  
playback.  
Enter face recognition data.  
3
Press MENU/OK to display face recognition  
data and enter the following information:  
NAME: Enter a name of up to 14 characters  
and press MENU/OK.  
BIRTHDAY: Enter the subject’s date of birth  
and press MENU/OK.  
CATEGORY: Choose the option that describes  
your relationship to the subject and press  
MENU/OK.  
Adding New Faces  
Follow the steps below to add faces to the face  
recognition database.  
Select REGISTER.  
Select REGISTER for nFACE RECOGNI-  
TION in the shooting menu.  
a
a
1
If you attempt to zoom in on the face of a person in-  
dicated by a green border in the face recognition da-  
tabase on their birthday, the camera will display their  
name and the message “Happy Birthday!”.  
To disable face recognition, select OFF.  
c
Face recognition may not be available depending on  
the shooting mode.  
Take a photograph.  
After checking that the  
subject is facing the cam-  
2
era, frame the subject us-  
ing the guides and take  
the photograph.  
a
If an error is displayed, take the photograph again.  
54  
nFace Recognition  
Viewing, Editing, and Deleting Existing Data  
Face Recognition  
The camera can store up to eight faces. If you attempt  
to add a ninth face, a confirmation dialog will be dis-  
played; use VIEW & EDIT to make room for new faces  
by deleting existing data.  
Follow the steps below to view, edit, or delete  
face recognition data.  
Select VIEW & EDIT for nFACE RECOG-  
NITION.  
1
When Intelligent Face Detection (P53) is on and the  
frame contains multiple subjects from the face rec-  
ognition database, the camera displays the name of  
the subject that will be used to set focus and expo-  
sure (the subject shown by the green frame). If no  
name is entered, the camera will show “---”. Subjects  
identified using face recognition but not used to set  
focus and exposure are shown by orange frames,  
other subjects by white frames.  
Select a face.  
2
View or edit face recognition data.  
3
The name, category, or birth date can be ed-  
ited as described in Step 3 of “Adding New  
Faces” (P54). To retake the photo, select RE-  
PLACING IMAGE and shoot a new portrait  
as described above.  
c
a
To delete face recognition data for the selected sub-  
The camera may fail to identify subjects in the face  
recognition database if they are not facing the cam-  
era or are only partly in the frame, or if details of the  
subjects’ faces or expressions differ markedly from  
those in the database.  
ject, select ERASE.  
55  
Taking RAW Pictures  
The camera can take RAW pictures. RAW pictures  
are unprocessed data read from the image sensor.  
To take RAW pictures, select j RAW in the setup  
menu (P104).  
The RAW Button  
Press the RAW button to temporarily change the re-  
cording format.  
Choose RAW+JPEG or RAW to record RAW pic-  
tures. If RAW+JPEG is selected, JPEG copies will  
also be recorded. Choose OFF to record pictures  
in JPEG format only.  
a
j options  
RAW+JPEG  
RAW  
OFF  
RAW button pressed  
JPEG  
JPEG  
• To convert RAW files for display on the camera, use  
j RAW CONVERSION in the playback menu (P92).  
• To convert RAW files for display on a computer, use  
the supplied RAW File Converter software.  
RAW+JPEG  
Taking a picture or pressing the RAW button again re-  
c
stores the previous setting.  
• Use a memory card when taking RAW pictures.  
• Crop, resize, and red-eye removal options are not  
available with RAW images during playback. The  
maximum zoom available when viewing RAW im-  
ages is 3.2×.  
56  
Playback Options  
To view the most recent picture in the monitor,  
press the abutton.  
Continuous Shooting  
In the case of pictures taken in continuous shoot-  
ing mode, only the first frame of each series will  
be displayed. Press the selector down to view the  
other pictures in the series.  
IFavorites: Rating Pictures  
Press the selector right to view pictures  
in the order recorded, left to view pic-  
tures in reverse order. Keep the selector  
pressed to scroll rapidly to the desired  
frame.  
To rate the picture currently displayed in full-frame  
playback, press DISP/BACK and press the selector  
up and down to select from zero to five stars.  
a
Pictures taken using other cameras are indicated by a  
m(“gift image”) icon during playback.  
Creating JPEG Copies of RAW Pictures  
Pressing the RAW button during playback displays  
RAW conversion options (P92).  
57  
Playback Options  
Playback Zoom  
Intelligent Face Detection  
Pictures taken with Intelligent Face Detection (P53)  
are indicated by a g icon. Press the f button to  
zoom in on the subject selected with Intelligent Face  
Detection. You can then use the kand nbuttons  
to zoom in and out.  
Press kto zoom in on pictures displayed in sin-  
gle-frame playback; n to zoom out. When the  
picture is zoomed in, the selector can be used to  
view areas of the image not currently visible in the  
display.  
Zoom indicator  
Navigation window  
shows portion of image  
currently displayed in  
monitor  
Press DISP/BACK or MENU/OK to exit zoom.  
a
• Rotate the command dial to view other pictures with-  
out changing the zoom ratio.  
• The maximum zoom ratio varies with image size.  
Playback zoom is not available with cropped or re-  
sized copies saved at a size of a or smaller.  
58  
Playback Options  
Multi-Frame Playback  
To change the number of images displayed, press Use the selector to highlight images and press  
nin single-frame view.  
MENU/OK to view the highlighted image full frame.  
In the nine- and hundred-frame displays, press  
the selector up or down to view more pictures.  
b Two-Frame Display  
Two-frame display can be used  
to compare pictures taken in  
Cmode.  
Press kto view  
fewer images.  
Press nto view  
more images.  
59  
ADeleting Pictures  
To delete individual pictures, multiple selected pictures, or all pictures,  
press MENU/OK, select AERASE (P90), and choose from the options be-  
low. Note that deleted pictures can not be recovered. Copy important  
pictures to a computer or other storage device before proceeding.  
Option  
Description  
Press the selector left or right to scroll through pictures and press MENU/OK to delete the current picture  
(a confirmation dialog is not displayed).  
FRAME  
Highlight pictures and press MENU/OK to select or deselect (pictures included in the photobook or print  
order are shown by S). When the operation is complete, press DISP/BACK to display a confirmation dia-  
log, then highlight OK and press MENU/OK to delete the selected pictures.  
SELECT FRAMES  
A confirmation dialog will be displayed; highlight OK and press MENU/OK to delete all unprotected pic-  
tures (if a memory card is inserted, only the pictures on the memory card will be affected; the pictures  
in internal memory are only deleted if no memory card is inserted). Pressing DISP/BACK cancels deletion;  
note that any pictures deleted before the button was pressed can not be recovered.  
ALL FRAMES  
a
• Protected pictures can not be deleted. Remove protection from any pictures you wish to delete (P94).  
• If a message appears stating that the selected images are part of a DPOF print order, press MENU/OK to delete the  
pictures.  
60  
Viewing Photo Information  
a
Photo information can be viewed by pressing the  
Use the command dial to view other images.  
The active focus point is shown by a+icon.  
info button.  
Zooming in on the Focus Point  
Press the f button to zoom in  
on the focus point. Press DISP/  
BACK or MENU/OK to return to full-  
frame playback.  
/
3
PLAYBACK  
INFORMATION 1  
AF  
INFORMATION 2  
61  
Image Search  
Search for images by various criteria.  
Select bIMAGE SEARCH in the playback  
menu (P90), highlight one of the following  
search criteria, and press MENU/OK:  
Select a search condition. Only pictures that  
match the search condition will be displayed.  
To delete or protect selected pictures or to  
view the selected pictures in a slide show,  
press MENU/OK and choose from the following  
options:  
1
2
Option  
Description  
Find all pictures taken on a selected  
date.  
BY DATE  
Find all pictures based on specified face  
information.  
BY FACE  
Option  
See page  
60  
AERASE  
Find all pictures with a specified rating  
(P57).  
Find all pictures that match a selected  
scene.  
BY IFAVORITES  
BY SCENE  
DPROTECT  
94  
ISLIDE SHOW  
92  
Find all still pictures, all movies, all pic-  
BY TYPE OF DATA tures taken in burst mode, or all RAW  
pictures.  
Find all pictures selected for upload to a  
specified destination (P91).  
BY UPLOAD MARK  
62  
XPhotoBook Assist  
Create books from your favorite photos.  
Creating a PhotoBook  
Scroll through the images and press the selec-  
tor up to select or deselect the current image  
for inclusion in the book. To display the current  
image on the cover, press the selector down.  
Select XPHOTOBOOK ASSIST in the play-  
back menu.  
5
1
Highlight NEW BOOK.  
2
a
The first picture selected automatically becomes  
the cover image. Press the selector down to select  
a different picture for the cover.  
Press MENU/OK to display the new  
book dialog.  
3
Choose pictures for the new book.  
SELECT FROM ALL: Choose from all the  
pictures available.  
SELECT BY IMAGE SEARCH: Choose from pictures  
matching selected search conditions (P62).  
4
Press MENU/OK to exit when the book  
is complete.  
6
7
Highlight COMPLETE PHOTOBOOK.  
a
Neither photographs a or smaller nor movies can  
be selected for photobooks.  
a
Choose SELECT ALL to select all photos, or all pho-  
tos matching the specified search conditions, for  
the book.  
63  
kPhotoBook Assist  
Press MENU/OK. The new book will be  
added to the list in the photobook  
assist menu.  
Viewing PhotoBooks  
8
Highlight a book in the photobook assist menu  
and press MENU/OK to display the book, then press  
the selector left and right to scroll through the  
pictures. Press DISP/BACK to return to the photo-  
book assist menu.  
c
• Photobooks can contain up to 300 pictures.  
• Books that contain no photos are automatically  
deleted.  
Editing and Deleting PhotoBooks  
PhotoBooks  
Photobooks can be copied to a computer using the  
supplied MyFinePix Studio software.  
Display the photobook and press  
1
MENU/OK to view book edit options.  
Choose from the following options:  
EDIT: Edit the book as described in “Creating a  
PhotoBook” on page 63.  
2
ERASE: Delete the current photobook.  
Follow the on-screen instructions.  
3
64  
Viewing Panoramas  
If you press the selector down when a panorama is displayed full frame, the camera will play back the  
picture from left to right or from bottom to top.  
PAUSE  
The following operations can be performed during playback:  
Opperaattiion  
Button  
Description  
Start/pause  
playback  
Press the selector down to start playback. Press again to pause.  
End playback  
Press the selector up to end playback.  
a
• Once displayed in full-frame playback, panoramas can be zoomed in or out using the zoom buttons.  
zpanoramas play back in an endless loop (P30); the playback direction can be controlled by pressing the  
selector left or right. The camera will not turn off automatically while playback is in progress (P102).  
65  
Recording Movies  
Press zto shoot a movie. During recording, the following indicators will  
be displayed and sound will be recorded via the built-in microphone (be  
careful not to cover the microphone during recording).  
y REC icon  
98  
18m39s  
Number of photos that  
can be taken during  
recording  
Time remaining  
To end recording, press the zbutton again. Recording ends automatically when the movie reaches  
maximum length or memory is full.  
a
• The focus mode can be changed during recording (P46).  
• Zoom can be adjusted while recording is in progress.  
• If the subject is poorly lit, the AF-assist lamp may light to assist the focus operation.  
To turn the AF-assist lamp off , select OFF for C AF ILLUMINATOR in the setup menu (P103).  
• Exposure and white balance are adjusted automatically throughout recording. The color and brightness of the  
image may vary from that displayed before recording begins.  
• Sounds made by the camera may be recorded.  
66  
Recording Movies  
Movie Frame Size  
Before recording, select a frame size using the  
WMOVIE MODE option in the shooting menu  
(P87).  
Taking Photographs during Recording  
Press the shutter button to take a photograph during  
recording.  
a
• Seepage88forinformationonchoosinghowphoto-  
graphs are recorded.  
• The photo is saved separately from the movie and  
does not appear as part of the movie.  
Option  
Description  
i 1920 (1920 × 1080) Full HD (High Definition).  
h 1280 (1280 × 720) High Definition.  
f (640 × 480)  
Standard definition.  
c
• Photos can not be taken while a high-speed movie  
is being recorded.  
High speed movie. Sound is not  
recorded, and focus, exposure,  
and white balance are not ad-  
justed automatically. Black bands  
appear at the top and bottom of  
movies recorded at Y320 × 112.  
Y640 × 480 (70fps)  
Y320 × 240 (120fps)  
• The number of photos that can be taken is limited.  
c
Y320 × 112 (200fps)  
• The indicator lamp lights while movies are being re-  
corded. Do not open the battery chamber during  
shooting or while the indicator lamp is lit. Failure  
to observe this precaution could prevent the movie  
from being played back.  
• Vertical or horizontal streaks may appear in movies  
containing very bright subjects. This is normal and  
does not indicate a malfunction.  
• The temperature of the camera may rise if it is used to  
record movies for an extended period or if the ambi-  
ent temperature is high. This is normal and does not  
indicate a malfunction.  
67  
aViewing Movies  
During playback (P57), movies  
are displayed in the monitor as  
shown at right. The following  
operations can be performed  
while a movie is displayed:  
Playback Speed  
Arrow  
Press the selector left or right to  
adjust playback speed. Speed is  
shown by the number of arrows  
(Mor N).  
Opperaattiion  
Description  
Press the selector down to start playback.  
b Viewing Movies on a Computer  
Start/ Press again to pause. While playback is  
pause paused, you can press the selector left or  
playback right to rewind or advance one frame at  
a time.  
End  
playback  
Copy movies to the computer before viewing.  
c
Do not cover the speaker during playback.  
Press the selector up to end playback.  
Adjust Press the selector left or right to adjust play-  
speed back speed during playback.  
Press MENU/OK to pause playback and dis-  
play volume controls. Press the selector  
Adjust  
up or down to adjust the volume and  
volume  
press MENU/OK to exit. Volume can also be  
adjusted from the setup menu.  
68  
Viewing Pictures on TV  
Connect the camera to a TV to show pictures to a group.  
Turn the camera off.  
1
2
Connect an A/V or HDMI cable (available from third-party suppliers).  
Connect white plug  
to audio-in jack  
Insert into A/V  
cable connector  
Connect yellow plug  
to video-in jack  
Insert into HDMI  
connector  
Insert into HDMI  
connector  
HDMI Mini Connector  
HDMI  
AnHDMIcable(availablefromthird-partysuppliers;P107)canbeusedtoconnectthecameratoHighDefini-  
tion (HD) devices (playback only). The USB cable or optional A/V cable cannot be used while an HDMI cable  
is connected.  
69  
Viewing Pictures on TV  
Tune the television to the video or HDMI input channel. See the documentation supplied with the  
television for details.  
3
4
Turn the camera on and press the abutton. The camera monitor turns off and pictures and mov-  
ies are played back on the TV. Note that the camera volume controls have no effect on sounds  
played on the TV; use the television volume controls to adjust the volume.  
a
Image quality drops during movie playback.  
c
When connecting the cable, be sure the connectors are fully inserted.  
70  
Printing Pictures via USB  
If the printer supports PictBridge, the camera can be connected directly to the printer and  
pictures can be printed without first being copied to a computer. Note that depending on  
the printer, not all the functions described below may be supported.  
Connecting the Camera  
Printing Selected Pictures  
Connect the supplied USB cable as shown and  
Press the selector left or right to display a pic-  
1
1
turn the printer on.  
ture you wish to print.  
Press the selector up or down to choose the  
number of copies (up to 99).  
2
Repeat steps 1–2 to select additional pictures.  
Press MENU/OK to display a confirmation dialog  
when settings are complete.  
3
Turn the camera on. t USB will be displayed  
in the monitor, followed by the PictBridge dis-  
play shown below at right.  
PRINT THESE FRAMES  
2
TOTAL:  
9
SHEETS  
USB  
YES  
CANCEL  
Press MENU/OK to start printing.  
4
SET  
71  
Printing Pictures via USB  
b Printing the Date of Recording  
Printing the DPOF Print Order  
To print the print order created with KPRINT  
ORDER (DPOF) in the playback menu (P97):  
To print the date of recording on pictures, press DISP/  
BACK in steps 1–2 to display the PictBridge menu (see  
“Printing the DPOF Print Order,” below). Press the se-  
lector up or down to highlight PRINT WITH DATE s  
and press MENU/OK to return to the PictBridge display  
(to print pictures without the date of recording, select  
PRINT WITHOUT DATE).  
In the PictBridge display, press DISP/BACK to  
open the PictBridge menu.  
1
PICTBRIDGE  
PRINT WITH DATE  
PRINT WITHOUT DATE  
PRINT DPOF  
a
If no pictures are selected when the MENU/OK button is  
pressed, the camera will print one copy of the current  
picture.  
Press the selector up or down to highlight  
u PRINT DPOF.  
2
Press MENU/OK to display a confirmation dialog.  
3
TOTAL:  
9
SHEETS  
YES  
CANCEL  
72  
Printing Pictures via USB  
a
Press MENU/OK to start printing.  
4
• Pictures can be printed from internal memory or a  
memory card that has been formatted in the camera.  
• If the printer does not support date printing, the  
PRINT WITH DATE s option will not be available in  
the PictBridge menu and the date will not be printed  
on the pictures in the DPOF print order.  
• When pictures are printed via direct USB connection,  
page size, print quality, and border selections are  
made using the printer.  
During Printing  
The message shown at right  
is displayed during printing.  
Press DISP/BACK to cancel be-  
fore all pictures are printed  
(depending on the printer,  
printing may end before the  
current picture has printed).  
PRINTING  
CANCEL  
If printing is interrupted, turn the camera off and then  
on again.  
Disconnecting the Camera  
Confirm that “PRINTING” is not displayed in the moni-  
tor and turn the camera off. Disconnect the USB  
cable.  
73  
Printing Pictures via USB  
Creating a DPOF Print Order  
The KPRINT ORDER (DPOF) option in the  
playback menu can be used to create a digital  
“print order” for PictBridge-compatible printers  
(P107) or devices that support DPOF.  
WITH DATE s/ WITHOUT DATE  
Select playback mode and press MENU/OK to  
display the playback menu.  
1
2
3
Highlight KPRINT ORDER (DPOF) and press  
MENU/OK.  
DPOF  
DPOF (Digital Print Order Format) is a stan-  
dard that allows pictures to be printed from  
“print orders” stored in internal memory or  
on a memory card. The information in the  
order includes the pictures to be printed, date im-  
print, and the number of copies of each picture.  
Highlight one of the following options and  
press MENU/OK:  
WITH DATE s: Print the date of recording on  
pictures.  
WITHOUT DATE: Do not print the date of record-  
ing on pictures.  
Press the selector left or right to display a pic-  
ture you wish to include in or remove from the  
print order.  
4
74  
Printing Pictures via USB  
Press the selector up or down to choose the  
number of copies (up to 99). To remove a pic-  
ture from the order, press the selector down  
until the number of copies is 0.  
Repeat steps 4–5 to complete the print order.  
Press MENU/OK to save the print order when set-  
tings are complete, or DISP/BACK to exit without  
changing the print order.  
5
6
7
The total number of prints is displayed in the  
monitor. Press MENU/OK to exit.  
Total number of prints  
Number of copies  
The pictures in the current  
print order are indicated by a  
u icon during playback.  
b Intelligent Face Detection  
If the current picture was created with Intelligent  
Face Detection, pressing fsets the number of cop-  
ies to the number of faces detected.  
a
When pictures are printed via direct USB connec-  
tion, page size, print quality, and border selections  
are made using the printer.  
75  
Printing Pictures via USB  
a
RESET ALL  
• Remove the memory card to create or modify a print  
order for the pictures in internal memory.  
• Print orders can contain a maximum of 999 pictures.  
• If a memory card is inserted  
containing a print order cre-  
ated by another camera, the  
message shown at right will  
be displayed. Pressing MENU/  
OK cancels the print order; a  
To cancel the current print  
order, select RESET ALL  
in the KPRINT ORDER  
(DPOF) menu. The confir-  
mation shown at right will  
YES  
CANCEL  
be displayed; press MENU/OK to remove all pictures  
from the order.  
YES  
NO  
new print order must be created as described above.  
76  
Viewing Pictures on a Computer  
The supplied software can be used to copy pictures to a computer, where they can be stored, viewed,  
organized, and printed. Before proceeding, install the software as described below. Do NOT connect the  
camera to the computer until installation is complete.  
Windows: Installing MyFinePix Studio  
Confirm that the computer meets the following system requirements:  
1
Windows 7 (SP 1)/Windows Vista (SP 2) 1  
3GHz Pentium 4 or better  
Windows XP (SP 3) 1  
2GHz Pentium 4 or better  
(2.4GHz Core 2 Duo or better)2  
512MB or more  
CPU  
(2.4GHz Core 2 Duo or better)2  
RAM  
Free disk space  
GPU  
1GB or more  
(1GB or more)2  
2GB or more  
Supports DirectX 9 or later  
Supports DirectX 7 or later  
(recommended)  
(required; performance not guaranteed with other GPUs)  
Video  
1,024×768 pixels or more with 24-bit color or better  
• Built-in USB port recommended. Operation is not guaranteed with other USB ports.  
Other  
• Internet connection (broadband recommended) required to install .NET Framework (if necessary), to use  
auto update feature, and when performing such tasks as sharing pictures on-line or via e-mail.  
1 Other versions of Windows are not supported. Only pre-installed operating systems are supported; operation is not  
guaranteed on home-built computers or computers that have been upgraded from earlier versions of Windows.  
2 Recommended when displaying HD movies.  
77  
Viewing Pictures on a Computer  
Start the computer. Log in to an account with administrator privileges before proceeding.  
2
3
Exit any applications that may be running and insert the installer CD in a CD-ROM drive.  
Windows 7/Windows Vista  
If an AutoPlay dialog is displayed, click SETUP.EXE. A “User Account Control” dialog will then be displayed;  
click Yes (Windows 7) or Allow (Windows Vista).  
The installer will start automatically; click Install MyFinePix Studio and follow the on-screen in-  
structions to install MyFinePix Studio and RAW FILE CONVERTER.  
If the Installer Does Not Start Automatically  
If the installer does not start automatically, select Computer or My Computer from the Start menu, then  
double-click the FINEPIX CD icon to open the FINEPIX CD window and double-click setup or SETUP.EXE.  
If prompted to install Windows Media Player, DirectX, or .NET Framework, follow the on-screen in-  
structions to complete installation.  
4
5
Remove the installer CD from the CD-ROM drive when installation is complete. Store the installer  
CD in a dry location out of direct sunlight in case you need to re-install the software.  
Installation is now complete. Proceed to “Connecting the Camera” on page 81.  
78  
Viewing Pictures on a Computer  
Macintosh: Installing FinePixViewer  
Confirm that the computer meets the following system requirements:  
1
CPU  
PowerPC or Intel (Core 2 Duo or better)*  
Pre-installed versions of Mac OS X version 10.3.9–10.6  
(visit http://www.fujifilm.com/support/digital_cameras/compatibility/ for more information)  
OS  
RAM  
256MB or more (1GB or more)*  
Free disk space A minimum of 200MB required for installation with 400MB available when FinePixViewer is running  
Video  
Other  
800×600 pixels or more with thousands of colors or better  
Built-in USB port recommended. Operation is not guaranteed with other USB ports.  
* Recommended when displaying HD movies.  
After starting the computer and quitting any applications that may be running, insert the installer  
CD in a CD-ROM drive and double-click Installer for Mac OS X.  
2
3
a
To install RAW FILE CONVERTER, double-click SILKYRFCEXInstaller. RAW FILE CONVERTER is used to view  
RAW images on your computer.  
An installer dialog will be displayed; click Installing FinePixViewer to start installation. Enter an  
administrator name and password when prompted and click OK, then follow the on-screen instruc-  
tions to install FinePixViewer. Click Exit to quit the installer when installation is complete.  
79  
Viewing Pictures on a Computer  
Remove the installer CD from the CD-ROM drive. Note that you may be unable to remove the CD  
if Safari is running; if necessary, quit Safari before removing the CD. Store the installer CD in a dry  
location out of direct sunlight in case you need to re-install the software.  
4
5
Mac OS X 10.5 or earlier: Open the “Applications” folder, start Image Capture, and select Preferences…  
from the Image Capture application menu. The Image Capture preferences dialog will be displayed;  
choose Other… in the When a camera is connected, open menu, then select FPVBridge in the  
“Applications/FinePixViewer” folder and click Open. Quit Image Capture.  
Mac OS X 10.6: Connect the camera and turn it on. Open the “Applications” folder and start Image  
Capture. The camera will be listed under DEVICES; select the camera and choose FPVBridge from  
the Connecting this camera opens menu and click Choose. Quit Image Capture.  
Installation is now complete. Proceed to “Connecting the Camera” on page 81.  
80  
Viewing Pictures on a Computer  
Connecting the Camera  
If the pictures you wish to copy are stored on a  
memory card, insert the card into the camera  
(P12).  
Turn the camera on. MyFinePix Studio or  
FinePixViewer will start automatically; follow  
the on-screen instructions to copy pictures to  
the computer. To exit without copying pic-  
tures, click Cancel.  
1
3
a
Windows users may require the Windows CD when  
starting the software for the first time.  
c
If the software does not start automatically, it may  
not be correctly installed. Disconnect the camera  
and reinstall the software.  
c
Loss of power during transfer could result in loss of  
data or damage to internal memory or the memory  
card. Charge the battery before connecting the  
camera.  
For more information on using the supplied soft-  
ware, start the application and select the appro-  
priate option from the Help menu.  
Turn the camera off and connect the supplied  
2
USB cable as shown, making sure the connec-  
tors are fully inserted. Connect the camera di-  
rectly to the computer; do not use a USB hub  
or keyboard.  
81  
Viewing Pictures on a Computer  
c
Disconnecting the Camera  
• If a memory card containing a large number of images  
is inserted, there may be a delay before the software  
starts and you may be unable to import or save im-  
ages. Use a memory card reader to transfer pictures.  
• Make sure that the computer does not display a mes-  
sage stating that copying is in progress and that the  
indicator lamp is out before turning the camera off or  
disconnecting the USB cable (if the number of imag-  
es copied is very large, the indicator lamp may remain  
lit after the message has cleared from the computer  
display). Failure to observe this precaution could re-  
sult in loss of data or damage to internal memory or  
the memory card.  
After confirming that the indicator lamp is out, follow  
the on-screen instructions to turn the camera off and  
disconnect the USB cable.  
Uninstalling the Supplied Software  
Only uninstall the supplied software when it is no lon-  
ger required or before beginning reinstallation. After  
quitting the software and disconnecting the camera,  
drag the “FinePixViewer” folder from “Applications”  
into the Trash and select Empty Trash in the Finder  
menu (Macintosh), or open the control panel and use  
“Programs and Features” (Windows 7/Windows Vista)  
or “Add or Remove Programs” (Windows XP) to unin-  
stall MyFinePix Studio. Under Windows, one or more  
confirmation dialogs may be displayed; read the con-  
tents carefully before clicking OK.  
• Disconnect the camera before inserting or removing  
memory cards.  
• In some cases, it may not be possible to access pictures  
saved to a network server using the supplied software  
in the same way as on a standalone computer.  
• The user bears all applicable fees charged by the  
phone company or Internet service provider when  
using services that require an Internet connection.  
82  
Using the Menus: Shooting Mode  
Use the shooting menus to adjust shooting set-  
tings. The options available vary with the shoot-  
ing mode selected.  
Shooting Menu Options  
Default values are shown in square brackets [ ].  
AE MODE  
Choose an option for E mode (P27).  
[R]  
Using the Shooting Menu  
Press MENU/OK to display the shoot-  
ing menu.  
1
AAdv. MODE  
[r]  
Choose an advanced shooting mode (P28).  
SCENE POSITION  
Choose a scene for SP mode (P32).  
NISO [AUTO (800)]  
Control the camera’s sensitivity to light (P49).  
Press the selector up or down to  
highlight the desired menu item.  
2
A
[L]  
Press the selector right to display op-  
tions for the highlighted item.  
3
Press the selector up or down to  
highlight the desired option.  
4
Press MENU/OK to select the high-  
lighted option.  
5
Press DISP/BACK to exit from the  
menu.  
6
83  
Using the Menus: Shooting Mode  
OIMAGE SIZE  
[O 4 : 3] TIMAGE QUALITY  
[FINE]  
O 4 : 3  
Choose the image size and  
aspect ratio at which pictures  
are recorded. Large pictures  
Choose how much image files are compressed.  
Option  
Description  
Size  
Aspect ratio  
Low compression. Select for higher image  
quality.  
High compression. Select this option to  
store more pictures.  
FINE  
NORMAL  
can be printed at large sizes with no drop in qual-  
ity, while small pictures require less memory, al-  
lowing more pictures to be recorded.  
Size Versus Aspect Ratio  
Size  
Option  
O
Prints at sizees up to  
34×25cm (13.5×10 in.)  
24×18 cm (9.5×7 in.)  
17×13 cm (7 × 5 in.)  
P
Q
Aspect ratio  
4 : 3: Pictures have the same proportions as the camera  
display.  
3 : 2: Pictures have the same proportions as a frame of  
35 mm film.  
16 : 9: Suited for display on High Definition (HD) de-  
vices.  
1 : 1: Pictures are square.  
84  
Using the Menus: Shooting Mode  
UDYNAMIC RANGE  
[AUTO] PFILM SIMULATION  
[c]  
Control contrast. Higher values are recommend- Simulate the effects of different types of film, in-  
ed for scenes that include both sunlight and deep cluding sepia and black-and-white.  
shade or for increased contrast with such subjects  
as sunlight on water, brightly-lit autumn leaves,  
portraits taken against a blue sky, and white ob-  
jects or people wearing white; note, however, that  
mottling may appear in pictures taken at higher  
values. If AUTO is selected, the camera will auto-  
matically select values between 100% and 400%  
in response to shooting conditions.  
Option  
Description  
Standard color reproduction. Suited to a  
wide range of subjects, from portraits to  
landscapes.  
c (PROVIA/  
STANDARD)  
d (Velvia/ A high-contrast palette of saturated col-  
VIVID)  
ors, suited to nature photographs.  
e (ASTIA/ A soft-toned palette of less saturated col-  
SOFT)  
b (MONO-  
CHROME)  
ors.  
Take pictures in black and white.  
Option  
A 100%  
Description  
Increase contrast when shooting  
indoors or under overcast skies.  
Take black-and-white pictures with  
slightly increased contrast. This setting  
also slightly tones down the brightness  
of the sky.  
e (MONO-  
CHROME +  
Ye FILTER)  
AUTO B 200%  
C 4000%  
Reduce loss of detail in highlights  
and shadows when photograph-  
ing high-contrast scenes.  
D 800%  
d (MONO- Take black-and-white pictures with in-  
CHROME +  
R FILTER)  
creased contrast. This setting also tones  
down the brightness of the sky.  
M 1600%  
a
f (MONO-  
Soften skin tones in black-and-white por-  
traits.  
M 1600% and D 800% are available only when CHROME +  
D-RANGE PRIORITY is selected in E mode.  
G FILTER)  
f (SEPIA) Take pictures in sepia.  
85  
Using the Menus: Shooting Mode  
dWB SHIFT  
RINTELLIGENT DIGITAL ZOOM  
[OFF]  
White balance can be fine-tuned. Adjust the se- Intelligent digital zoom can be used to magnify  
lected color axis (R–Cy=Red-Cyan or B-Ye=Blue– the image by 1.4× or 2× while processing it for  
Yellow) by +9 to –9 in increments of one.  
sharp, high-resolution results.  
a
• Intelligent digital zoom may end when another mode  
is selected.  
fCOLOR  
Adjust color density.  
[MID]  
• Intelligent digital zoom may sometimes produce low-  
er quality images than optical zoom.  
• The time needed to record images increases.  
• The effects are not visible in the display during shoot-  
ing.  
HSHARPNESS  
Choose whether to sharpen or soften outlines.  
[STD]  
rHIGHLIGHT TONE  
Adjust the appearance of highlights.  
[STD]  
• Intelligent digital zoom is not available in continuous  
mode or during movie recording.  
sSHADOW TONE  
Adjust the appearance of shadows.  
[STD]  
[STD]  
ZADVANCED ANTI BLUR  
[ON]  
Select ON to enable advanced anti blur in R  
mode (P28).  
hNOISE REDUCTION  
Choose the amount of noise reduction.  
bFACE DETECTION  
Choose whether the camera automatically de-  
tects and sets focus and exposure for human por-  
trait subjects (P53).  
86  
Using the Menus: Shooting Mode  
FAF MODE  
[t] nFACE RECOGNITION  
Choose how the camera selects the focus area Add portrait subjects to the face recognition da-  
wheninAF-S focusmode(P46). Note that regard- tabase. These subjects will be given priority dur-  
less of the option selected, the camera will focus ing Intelligent Face Detection, and their names  
on the subject in the center of the monitor when and other information can be viewed during  
macro mode is on (P36).  
playback (P54).  
s MULTI: When the shutter button is pressed  
halfway, the camera detects high-contrast sub-  
jects near the center of the frame and selects  
the focus area automatically.  
WMOVIE MODE  
Choose a frame size for movies (P67).  
[i]  
t AREA: Choose the focus area manually  
(P48).  
x TRACKING: Position the subject in the fo-  
cus target and press the selector left. The cam-  
era will track the subject and adjust focus as it  
moves through the frame.  
a
Note that in x mode, the camera focuses continu-  
ously, increasing the drain on the battery, and that the  
sound of the camera focusing may be audible.  
87  
Using the Menus: Shooting Mode  
a STILL SHOOTING IN MOVIE  
[MOVIE PRIORITY]  
gEXTERNAL FLASH  
Choose ON when using an optional flash unit (ex-  
[OFF]  
Choose how the camera records photographs cept Fujifilm products) mounted on the camera  
taken during movie recording (P67).  
hot shoe.  
Option  
Description  
c
• The flash may not fully light the subject at speeds  
The camera interrupts filming to take the  
photograph and resumes filming automati-  
cally when recording is complete. Image  
size is determined by the option selected  
faster than 1 1000 s.  
/
STILL  
IMAGE  
• Use auto or custom white balance (P50).  
• If the built-in flash is raised when ON is selected for  
gEXTERNAL FLASH, the built-in flash will fire once  
to provide a signal for the optional flash unit to fire.  
• External flash units can be used in P, S, A, M or EXR  
(S and T only) modes.  
PRIORITY for OIMAGE SIZE, but note that the pho-  
tograph will be recorded at size Pif Ois  
selected.  
The camera takes a photograph without  
MOVIIEE  
interrupting movie recording. Image size  
• Fujifilm external flash units do not require this setting.  
PRIORITY is determined by the option selected for  
a
WMOVIE MODE.  
• The camera can be used with flash units that provide  
aperture adjustment, external metering, and sensitiv-  
ity control. Some flash units that are designed spe-  
cifically for other cameras can not be used.  
• For information on Fujifilm external flash units, see  
Accessories from FUJIFILM (P108).  
IFLASH  
[ 0]  
Adjust flash brightness. Choose from values be-  
2
2
/
/
tween + 3 EV and – 3 EV. The default setting is 0.  
Note that the desired results may not be achieved  
depending on shooting conditions and the dis-  
tance to the subject.  
88  
Using the Menus: Shooting Mode  
KCUSTOM SET  
Save settings for P, S, A, M and all EXR modes ex- Choose the items displayed in the LCD monitor  
cept R (P26). (P6). The following items can be displayed:  
vDISP. CUSTOM SETTING  
FRAMING GUIDLINE*  
WHITE BALANCE  
HISTOGRAM  
IMAGE SIZE/QUALITY  
PHOTOMETRY  
ELECTRONIC LEVEL  
APERTURE/S-SPEED/ISO  
FRAMES REMAINING  
BATTERY LEVEL  
FLASH  
FILM SIMULATION  
EXP. COMPENSATION  
DYNAMIC RANGE  
* You can also select the grid type (P105).  
See pages 5–6 for the locations of these items in  
the displays.  
Virtual Horizon  
Selecting ELECTRONIC LEVEL  
displays a virtual horizon. The  
camera is level when the two  
lines overlap.  
a
The virtual horizon may not be displayed if the cam-  
era lens is pointed up or down.  
89  
Using the Menus: Playback Mode  
Using the Playback Menu  
Playback Menu Options  
Press the a button to enter play-  
back mode.  
1
XPHOTOBOOK ASSIST  
Create books from your favorite photos (P63).  
Press MENU/OK to display the play-  
back menu.  
2
bIMAGE SEARCH  
Search for pictures (P62).  
Press the selector up or down to  
highlight the desired menu item.  
3
xERASE  
Delete all or selected pictures (P60).  
Press the selector right to display op-  
4
tions for the highlighted item.  
Press the selector up or down to  
highlight the desired option.  
5
Press MENU/OK to select the high-  
lighted option.  
6
Press DISP/BACK to exit from the  
menu.  
7
90  
Using the Menus: Playback Mode  
jMARK FOR UPLOAD TO  
Select pictures for upload to YouTube or Face-  
book using MyFinePix Studio (Windows only).  
RESEETT ALLLL:: DDeesseelleeccttiinngg All Pictures  
Choose RESET ALL to deselect all pictures. If the  
number of pictures affected is very large, a mes-  
sage will be displayed while the operation is in  
progress. Press DISP/BACK to exit before the opera-  
tion is complete.  
Selecting Pictures for Uppload  
Select YouTube to choose movies for upload  
to YouTube, FACEBOOK to choose photos and  
movies for upload to Facebook.  
1
Uploadinng Picturees (Windoows Only)  
Selected pictures can be uploaded using the  
YouTube/Facebook Upload option in MyFinePix  
Studio.  
Press the selector left or right to display pic-  
2
tures and press MENU/OK to select or deselect.  
Press DISP/BACK to exit when all the desired pic-  
tures are selected.  
Select with camera  
a
• Only movies can be selected for upload to YouTube.  
• During playback, selected pictures are indicated by  
jYouTube or jFACEBOOK icons.  
Upload from computer  
For information on installing MyFinePix Studio  
and connecting the camera to a computer, see  
“Viewing Pictures on a Computer” (P77).  
91  
Using the Menus: Playback Mode  
ISLIDE SHOW  
View pictures in an automated slide show. Choose Create JPEG copies of RAW pictures (P56). The  
the type of show and press MENU/OK to start. original image data are unaffected, allowing a  
[MULTIPLE] jRAW CONVERSION  
Press DISP/BACK at any time during the show to single RAW image to be processed in a multitude  
view on-screen help. The show can be ended at of different ways.  
any time by pressing MENU/OK.  
Select jRAW CONVER-  
1
Option  
Description  
SION in the playback menu.  
Press selector left or right to go back or  
skip ahead one frame. Select FADE-IN  
for fade transitions between frames.  
As above, except that camera automati-  
cally zooms in on faces selected with In-  
telligent Face detection.  
NORMAL  
FADE-IN  
NORMAL g  
Press the selector up or down to highlight a  
setting and press the selector right to select.  
Press the selector up or down to highlight the  
desired option and press MENU/OK to select and  
return to the settings list. Repeat this step to  
adjust additional settings.  
2
3
FADE-IN g  
MULLTTIIPPLE  
a
Display several pictures at once.  
The camera will not turn off automatically while a slide  
show is in progress.  
Press the RAW button to  
preview the JPEG copy.  
Press MENU/OK to save the  
copy or press DISP/BACK to  
return to Step 2.  
92  
Using the Menus: Playback Mode  
BRED EYE REMOVAL  
Setting  
Description  
Create a JPEG copy using the set-  
tings in effect at the time the photo  
was taken.  
If the current picture is marked with a gicon to  
indicate that it was taken with Intelligent Face De-  
tection, this option can be used to remove red-  
eye. The camera will analyze the image; if red-eye  
is detected, the image will be processed to create  
a copy with reduced red-eye.  
REFLECCTT SSHHOOOOTTIINNG  
COND.  
PUSSHH/PULL  
PROCESSING  
Adjust exposure by –1 EV to +1 EV in  
/
increments of 1 3EV (P44).  
Enhance details in highlights for  
natural contrast (P85).  
Simulate the effects of different  
types of film (P85).  
Adjust white balance (P50).  
Fine-tune white balance (P86).  
Adjust color density (P86).  
Sharpen or soften outlines (P86).  
Process the copy to reduce mot-  
tling (P86).  
DYYNNAMMICC RANGE  
FILM SIMUULATIOON  
Display the desired picture.  
1
2
Select BRED EYE REMOVAL in the playback  
menu.  
WHITE BAALLAANNCCE  
WB SHIFT  
COLOR  
Press MENU/OK.  
3
SHAARPNESS  
a
NOISSEE RREEDDUUCCTTIION  
• Red-eye may not be removed if the camera is unable  
to detect a face or the face is in profile. Results may  
differ depending on the scene. Red-eye can not be  
removed from pictures that have already been pro-  
cessed using red-eye removal or pictures created  
with other devices.  
HIGHLIGGHHT TOONE  
SHADOOW TTOONE  
Adjust highlights (P86).  
Adjust shadows (P86).  
Choose the color space used for  
color reproduction (P105).  
COOLLOORR SSPACE  
• The amount of time needed to process the image  
varies with the number of faces detected.  
• Copies created with BRED EYE REMOVAL are indi-  
cated by a eicon during playback.  
93  
Using the Menus: Playback Mode  
DPROTECT  
GCROP  
Protect pictures from accidental deletion.  
Create a cropped copy of the current picture.  
Select DPROTECT in the playback menu.  
Display the desired picture.  
1
2
1
Highlight one of the following options and  
press MENU/OK:  
FRAME: Protect selected pictures. Press the  
selector left or right to view pictures and  
press MENU/OK to select or deselect. Press  
DISP/BACK when the operation is complete.  
SET ALL: Protect all pictures.  
Select GCROP in the playback menu.  
2
Use the kand nbuttons to zoom the image  
in and out and use the selector to scroll the  
picture until the desired portion is displayed.  
3
Press MENU/OK to display a confirmation dialog.  
4
5
a
Press MENU/OK again to save the cropped copy  
to a separate file.  
RESET ALL: Remove protection from all pic-  
tures.  
c
Protected pictures will be deleted when the memory  
card or internal memory is formatted (P100).  
Larger crops produce larger copies; all copies have an  
aspect ratio of 4:3. If the size of the final copy will be  
a, OK will be displayed in yellow.  
b Intelligent Face Detection  
If the picture was shot with Intelligent Face Detection  
(P53), gwill be displayed in the monitor. Press the f  
button to zoom in on the selected face.  
94  
Using the Menus: Playback Mode  
ORESIZE  
CIMAGE ROTATE  
Create a small copy of the current picture.  
Rotate pictures taken in tall orientation so that  
they are displayed in tall orientation in the LCD  
monitor.  
Display the desired picture.  
1
Select ORESIZE in the playback menu.  
2
Display the desired picture.  
1
2
Highlight a size and press MENU/OK to display a  
confirmation dialog.  
3
Select CIMAGE ROTATE in the playback  
menu.  
Press MENU/OK to save the resized copy to a  
separate file.  
4
a
Press the selector down to rotate the picture  
90° clockwise, up to rotate it 90° counterclock-  
wise.  
3
The sizes available vary with the size of the original im-  
age.  
Press MENU/OK. The picture automatically be  
displayed in the selected orientation when-  
ever it is played back on the camera.  
4
a
• Protected pictures can not be rotated. Remove pro-  
tection before rotating pictures (P94).  
• The camera may not be able to rotate pictures cre-  
ated with other devices.  
95  
Using the Menus: Playback Mode  
ECOPY  
FVOICE MEMO  
Copy pictures from internal memory to a memory Add a voice memo to the current photograph.  
card.  
Holding the camera at a distance of about 20 cm,  
face the microphone and press MENU/OK to begin  
recording. Press MENU/OK again to end recording  
Select ECOPY in the playback menu.  
1
2
Highlight one of the following options and (recording ends automatically after 30 seconds).  
press the selector right:  
a
aINTERNAL MEMORY ybCARD: Copy pic-  
tures from internal memory to a memory  
card.  
• Voice memos can not be added to movies or protect-  
ed pictures. Remove protection from pictures before  
recording voice memos.  
• If a voice memo already exists for the current picture,  
the options will be displayed. Select RE-REC to re-  
place the existing memo.  
bCARD yaINTERNAL MEMORY: Copy pic-  
tures from a memory card to internal mem-  
ory.  
Playing Voice Memos  
Highlight one of the following options and  
press MENU/OK:  
FRAME: Copy selected pictures. Press the se-  
lector left or right to view pictures and press  
MENU/OK to copy the current picture.  
ALL FRAMES: Copy all pictures.  
3
Pictures with voice memos are indicated by a qicon  
during playback. To play the voice memo back, select  
PLAY for FVOICE MEMO in the playback menu.  
a
• The camera may not play voice memos recorded  
with other devices.  
• Do not cover the speaker during playback.  
a
• Copying ends when the destination is full.  
• DPOF print information is not copied (P74).  
96  
Using the Menus: Playback Mode  
nERASE FACE RECOG.  
JDISP. ASPECT  
[4 : 3]  
Remove face recognition links from the current Choose how High Definition (HD) devices display  
image. When this option is selected, the camera pictures with an aspect ratio of 4 : 3 (this option is  
will zoom in on an area in the current picture that available only when an HDMI cable is connected).  
it has matched with a face in the face recognition Select 16 : 9 to display the image so that it fills the  
database. If the match is not correct, press MENU/ screen with its top and bottom cropped out, 4 : 3  
OK to remove the link to the face recognition da- to display the entire image with black bands at  
tabase.  
either side.  
a
Face recognition links can not be removed from copies  
with a size of aor smaller.  
KPRINT ORDER (DPOF)  
Select pictures for printing on DPOF- and Pict-  
16 : 9  
4 : 3  
Bridge-compatible devices (P72).  
a
Photographs with an aspect ratio of 16 : 9 are displayed  
full screen, those with an aspect ratio of 3:2/1:1 in a  
black frame.  
97  
The Setup Menu  
Using the Setup Menu  
Display the setup menu.  
Adjust settings.  
1 1.1 Press  
2 2.1 Press the selector right to acti-  
MENU/OK to display the  
menu for the current mode.  
vate the setup menu.  
1.2 Press the selector left to high-  
2.2 Press the selector up or down  
light a left tab.  
to highlight a menu item.  
1.3 Press the selector up or down  
to select 4.  
2.3 Press the selector right to dis-  
play options for the highlighted  
item.  
The setup menu appears.  
2.4 Press the selector up or down  
to highlight an option.  
Tab  
2.5 Press MENU/OK to select the  
highlighted option.  
2.6 Press DISP/BACK to exit from the  
menu.  
98  
The Setup Menu  
Setup Menu Options  
Default values are shown in square brackets [ ].  
Option  
h HOME  
Description  
Switch to the time currently selected  
for FDATE/TIME (see above).  
Switch to local time. If this option is  
selected, g and the time and date  
will be displayed in yellow for three  
seconds each time the camera is  
turned on.  
FDATE/TIME  
Set the camera clock (P16).  
NTIME DIFFERENCE  
[h]  
g LOCAL  
Switch the camera clock instantly from your  
home time zone to the local time at your desti-  
nation when traveling. To specify the difference  
between local time and your home time zone:  
La  
Choose a language (P16).  
Highlight g LOCAL and press the selector  
right.  
1
oSILENT MODE  
[OFF]  
Select ON to disable the speaker, flash, and AF-  
assist illuminator in situations in which camera  
sounds or lights may be unwelcome (note that  
the flash will still fire in Cmode).  
Use the selector to choose the time difference  
between local time and your home time zone.  
2
Press MENU/OK.  
3
To switch between local time and your home  
time zone, highlight g LOCAL or h HOME and  
press MENU/OK.  
99  
The Setup Menu  
RRESET  
AIMAGE DISP.  
[1.5 SEC]  
Reset all settings except FDATE/TIME, NTIME Choose how long pictures are displayed in the  
DIFFERENCE, OBACKGROUND COLOR, and LCD monitor after shooting.  
QVIDEO SYSTEM to default values.  
Option  
Description  
Pictures are displayed for three sec-  
onds (3 SEC) or 1.5 seconds (1.5 SEC).  
Colors may differ slightly from those  
in the final image.  
Highlight RRESET and press the selector  
right to display a confirmation dialog.  
3 SEC  
1
1.5 SEC  
ZOOM  
Highlight OK and press MENU/OK.  
2
Pictures are displayed until the MENU/  
KFORMAT  
(CONTINUOUS) OK button is pressed.  
Pictures are not displayed after  
shooting.  
If a memory card is inserted in the camera, this  
option will format the memory card. If no memo-  
ry card is inserted, this option will format internal  
memory.  
OFF  
a
OFF has no effect in continuous shooting mode.  
c
• All data—including protected pictures—will be de-  
leted from the memory card or internal memory. Be  
sure important files have been copied to a computer  
or other storage device.  
• Do not open the battery-chamber cover during for-  
matting.  
100  
The Setup Menu  
a
• If the frame number reaches 999-9999, the shutter  
release will be disabled (P117).  
• Selecting RRESET (P100) sets BFRAME NO. to  
CONTINUOUS but does not reset the file number.  
• Frame numbers for pictures taken with other cam-  
eras may differ.  
BFRAME NO.  
[CONT.]  
Frame number  
Newpicturesarestoredinim-  
age files named using a four-  
digit file number assigned  
by adding one to the last file  
number used. The file num-  
ber is displayed during play-  
back as shown at right. BFRAME NO. controls  
whether file numbering is reset to 0001 when a  
new memory card is inserted or the current mem-  
ory card or internal memory is formatted.  
100-0001  
Directory  
number  
File  
number  
GOPERATION VOL.  
[c]  
Adjust the volume of the sounds produced when  
camera controls are operated. Choose e OFF  
(mute) to disable control sounds.  
Option  
Description  
HSHUTTER VOLUME  
[c]  
Numbering continues from the last  
file number used or the first avail-  
able file number, whichever is higher.  
Choose this option to reduce the  
number of pictures with duplicate  
file names.  
Numbering is reset to 0001 after for-  
matting or when a new memory card  
is inserted.  
Adjust the volume of the sounds produced when  
the shutter is released. Choose e OFF (mute) to  
disable the shutter sound.  
CONTINUOUS  
eSHUTTER SOUND  
[k]  
Choose the sound made by the shutter.  
RENEW  
101  
The Setup Menu  
IPLAYBACK VOLUME  
[7]  
1QUICK START MODE  
[OFF]  
Adjust the volume for movie and voice memo  
playback.  
Allow the camera to restart in a fast manner after  
turned off (ON/OFF).  
c
JLCD BRIGHTNESS  
[0]  
This option will increase drain on the battery. Quick  
start mode is cancelled automatically if no operations  
are performed for about 20 minutes.  
Control the brightness of the display.  
TMONITOR SUNLIGHT MODE  
[OFF]  
Select ON to make the display in the monitor eas-  
ier to read in bright light.  
FFn BUTTON  
[Fn1: R/ Fn2: FOCUS CHECK]  
Choose the role played by the Fn1/Fn2 button  
(P52).  
EEVF/LCD MODE  
Choose 30 fps to increase battery life, 50 fps for  
[50fps]  
improved display quality.  
MAUTO POWER OFF  
[2 MIN]  
Choose the length of time before the camera  
turns off automatically when no operations are  
performed. Shorter times increase battery life; if  
OFF is selected, the camera must be turned off  
manually. Note that in some situations the cam-  
era turns off automatically even when OFF is se-  
lected.  
102  
The Setup Menu  
LDUAL IS MODE  
[L] BRED EYE REMOVAL  
[ON]  
Choose from the following image stabilization Choose ON to remove red-eye effects caused by  
options:  
the flash when shooting with Intelligent Face De-  
tection.  
Description  
Option  
L
Image stabilization on. If + MOTION  
is selected, the camera will adjust  
shutter speed to reduce motion blur  
when a moving objects are detected.  
As above, except that image stabili-  
zation is performed only when the  
shutter button is pressed halfway or  
the shutter is released.  
a
• Red-eye reduction is performed only when a face is  
detected.  
CONTINUOUS +  
MOTION  
l CONTINUOUS  
M SHOOTING  
+ MOTION  
• Red-eye removal is not available with RAW images.  
CAF ILLUMINATOR  
[ON]  
m
If ON is selected, the AF-assist illuminator will light  
to assist autofocus.  
SHOOTING ONLY  
Image stabilization off. Choose this  
option when using a tripod.  
OFF  
c
• The camera may be unable to focus using the AF-as-  
sist illuminator in some cases. If the camera is unable  
to focus in macro mode, try increasing the distance to  
the subject.  
• Avoid shining the AF-assist illuminator directly into  
your subject’s eyes.  
c
+ MOTION has no effect when sensitivity is set to a  
fixed value, and may also be unavailable at some other  
combinations of settings. The effect may vary with  
lighting conditions and the speed at which the object  
is moving.  
103  
The Setup Menu  
kAE/AF-LOCK MODE  
[P] IFOCUS RING  
[XCW]  
If AE&AF ON WHEN PRESSING is selected, ex- Choose the direction in which the focus ring is ro-  
posure and/or focus will lock while the AE/AF LOCK tated to increase the focus distance.  
button is pressed. If AE&AF ON/OFF SWITCH is  
selected, exposure and/or focus will lock while the  
AE/AF LOCK button is pressed and remain locked  
until the button is pressed again (P35).  
vAE/AF-LOCK BUTTON  
[AE-L]  
Choose whether the AE/AF LOCK button locks only  
exposure, only focus, or both exposure and focus  
(AE-L /AF-L /AE+AF).  
jRAW  
[OFF]  
Choose whether RAW pictures are recorded  
(P56).  
104  
The Setup Menu  
zFRAMING GUIDLINE  
[FGRID 9] JCOLOR SPACE  
[sRGB]  
Choose the type of framing grid available in Choose the gamut of colors available for color re-  
shooting mode.  
production.  
FGRID 9  
Description  
Recommended in most situations.  
For commercial printing.  
Option  
sRGGB  
Addoobbee RGB  
For “rule of thirds” composition.  
tSAVE ORG IMAGE  
[OFF]  
Choose ON to save unprocessed copies of seam-  
less z panoramas or pictures taken using  
B RED EYE REMOVAL, jPRO LOW-LIGHT  
MODE, or iPRO FOCUS MODE.  
GGRID 24  
A six-by-four grid.  
HHD FRAMING  
Frame HD pictures in the crop  
shown by the lines at the top  
and bottom of the display.  
105  
The Setup Menu  
mAUTOROTATE PB  
[ON] QVIDEO SYSTEM  
Choose ON to automatically rotate “tall” (portrait- Choose a video mode for connection to a TV.  
orientation) pictures during playback.  
Option  
NTSC  
Description  
Select this mode for connection to  
video devices in North America, the  
Caribbean, parts of Latin America,  
and some East Asian countries.  
Select this mode for connection to  
video devices in the United Kingdom  
and much of Europe, Australia, New  
Zealand, and parts of Asia and Africa.  
OBACKGROUND COLOR  
Choose a color scheme.  
[BLACK]  
[ON]  
cGUIDANCE DISPLAY  
Choose whether to display tool tips.  
PAL  
SCUSTOM RESET  
Reset all settings for mode C1/C2/C3. A confir-  
mation dialog will be displayed, press the selector  
up or down to highlight OK and press MENU/OK.  
106  
Optional Accessories  
The camera supports a wide range of accessories from FUJIFILM and other manufacturers.  
Printing  
Flash Photoggrraphy  
DIGITAL CAMERA  
X-S1  
USB  
EF-20 shoe  
mount flash  
(sold separately)  
EF-42 shoe  
mount flash  
(sold separately)  
PictBridge-compatible printer  
(available from third-party  
suppliers)  
SD/SDHC/SDXC  
memory card  
Externnaall MMiiccrroopphhoones  
External microphone  
(available from third-  
party suppliers)  
Printer (available from  
third-party suppliers)  
Audiioo//VVisual  
Computer Related  
A/V cable  
USB  
Standard TV (available from  
third-party suppliers)  
SD card slot or card reader  
HDMI cable  
Computer (available from  
third-party suppliers)  
HDTV (available from  
third-party suppliers)  
107  
Optional Accessories  
Accessories from FUJIFILM  
The following optional accessories are available from FUJIFILM. For the latest information on the acces-  
sories available in your region, check with your local FUJIFILM representative or visit http://www.fujifilm.  
com/products/digital_cameras/index.html.  
Rechargeable  
NP-95: Additional large-capacity NP-95 rechargeable batteries can be  
Li-iioonn bbatttteerries purchased as required.  
Batttteeryy chharrgers BC-65N: Replacement battery chargers can be purchased as required. The  
BC-65N charges an NP-95 battery in about 210 minutes at +20°C (+68°F).  
Shoe Moount Flash EF-20: Hot-shoe clip-on flash, guide number: 20 (ISO 100), compatible with  
i-TTL, bounce capability: up to 90°, power source: 2 AA-size 1.5V batteries.  
Shoe Moount Flash EF-42: Hot-shoe clip-on flash, guide number: up to 42 (ISO 100), auto zoom:  
24-105mm (equivalent to 135 format), compatible with i-TTL, bounce ca-  
pability: up to 90°, power source: 4 AA-size 1.5V batteries.  
108  
Caring for the Camera  
To ensure continued enjoyment of the product, observe the following precautions.  
Storraggee aanndd UUssee  
Condensation  
If the camera will not be used for an extended pe-  
riod, remove the battery and memory card. Do  
not store or use the camera in locations that are:  
• exposed to rain, steam, or smoke  
• very humid or extremely dusty  
• exposed to direct sunlight or very high tempera-  
tures, such as in a closed vehicle on a sunny day  
• extremely cold  
Sudden increases in temperature, such as occur  
when entering a heated building on a cold day,  
can cause condensation inside the camera. If this  
occurs, turn the camera off and wait an hour be-  
fore turning it on again. If condensation forms on  
the memory card, remove the card and wait for  
the condensation to dissipate.  
Clleeaniing  
• subject to strong vibration  
Use a blower to remove dust from the lens and  
monitor, then gently wipe with a soft, dry cloth.  
Any remaining stains can be removed by wiping  
gently with a piece of FUJIFILM lens-cleaning pa-  
per to which a small amount of lens-cleaning fluid  
has been applied. Care should be taken to avoid  
scratching the lens or monitor. The camera body  
can be cleaned with a soft, dry cloth. Do not use  
alcohol, thinner, or other volatile chemicals.  
• exposed to strong magnetic fields, such as near  
a broadcasting antenna, power line, radar emit-  
ter, motor, transformer, or magnet  
• in contact with volatile chemicals such as pesti-  
cides  
• next to rubber or vinyl products  
Wateerr aanndd SSandd  
Exposure to water and sand can also damage the  
camera and its internal circuitry and mechanisms.  
When using the camera at the beach or seaside,  
avoid exposing the camera to water or sand. Do  
not place the camera on a wet surface.  
Traveeling  
Keep the camera in your carry-on baggage.  
Checked baggage may suffer violent shocks that  
could damage the camera.  
109  
Problems and Solutions  
Power and Battery  
Problem  
Solluution  
The battery is exhausted: Charge the battery or insert a fully-charged spare battery (P9).  
The battery is inserted incorrectly: Reinsert in the correct orientation (P10).  
The battery-chamber cover is not latched: Latch the battery-chamber cover (P10).  
The camera does not  
turn on.  
The battery is cold: Warm the battery by placing it in a pocket or other warm place and reinsert it  
in the camera immediately before taking a picture.  
There is dirt on the battery terminals: Clean the terminals with a soft, dry cloth.  
ON is selected for TMONITOR SUNLIGHT MODE: Select OFF to reduce the drain on the bat-  
tery (P4).  
The battery runs down  
quickly.  
R is selected for shooting mode: Select Bmode to reduce the drain on the battery (P22).  
xTRACKING is selected for FAF MODE: Select a different AF mode (P87).  
AF-C is selected for focus mode: Select a different focus mode (P46).  
The battery has been charged many times: The battery has reached the end of its charging life. Pur-  
chase a new battery.  
The camera turns off  
suddenly.  
The battery is exhausted: Charge the battery or insert a fully-charged spare battery (P9).  
Charging does not start. Reinsert the battery in the correct orientation and make sure that the charger is plugged in (P9).  
Charging is slow.  
Charge the battery at room temperature (Pvi).  
There is dirt on the battery terminals: Clean the terminals with a soft, dry cloth.  
The charging lamp lights,  
but the battery does not  
charge.  
The battery has been charged many times: The battery has reached the end of its charging life. Pur-  
chase a new battery. If the battery still fails to charge, contact your FUJIFILM dealer.  
The battery is too hot or too cold: Wait for the battery temperature to stabilize (P9).  
110  
Problems and Solutions  
Menus and Displays  
Problem  
Menus and displays are  
not in English.  
Solluution  
Select ENGLISH for Qa (P16, 99).  
Shooting  
Problem  
Solluution  
Memory is full: Insert a new memory card or delete pictures (P12, 60).  
Memory is not formatted: Format the memory card or internal memory (P100).  
There is dirt on the memory card contacts: Clean the contacts with a soft, dry cloth.  
The memory card is damaged: Insert a new memory card (P12).  
The battery is exhausted: Charge the battery or insert a fully-charged spare battery (P9).  
The camera has turned off automatically: Turn the camera on (P15).  
The indicator lamp was orange when you attempted to record a panorama: Wait until the indicator lamps  
turns off (P20).  
No picture is taken when  
the shutter button is  
pressed.  
The LCD monitor goes  
dark after shooting.  
The LCD monitor may darken while the flash charges. Wait for the flash to charge (P37).  
The subject is close to the camera: Select macro mode (P36).  
The subject is far away from the camera: Cancel macro mode (P36).  
The subject is not suited to autofocus: Use focus lock (P34).  
The camera does not  
focus.  
If Sis selected for OIMAGE SIZE in R mode, the camera will optimize not only sensitivity and  
other settings, but also image size. To record all pictures at the same size, choose another shooting  
mode or select another option for OIMAGE SIZE (P84).  
Pictures are not the same  
size.  
Macro mode is not avail-  
able.  
Choose a different shooting mode (P22).  
Intelligent Face Detection Intelligent Face Detection is not available in the current shooting mode: Choose a different shooting mode  
is not available. (P22).  
111  
Problems and Solutions  
Problem  
Solluution  
The subject’s face is obscured by sunglasses, a hat, long hair, or other objects: Remove the obstructions.  
The subject’s face occupies only a small area of the frame: Change the composition so that the sub-  
ject’s face occupies a larger area of the frame (P34).  
The subject’s head is tilted or horizontal: Ask the subject to hold their head straight.  
The camera is tilted: Keep the camera level (P18).  
No face is detected.  
The subject’s face is poorly lit: Shoot in bright light.  
Wrong subject is se-  
lected.  
The selected subject is closer to the center of the frame than the main subject. Recompose the  
picture or turn face detection off and frame the picture using focus lock (P34).  
The flash is lowered: Raise the flash (P37).  
The flash is not available in the current shooting mode: Choose a different shooting mode (P22).  
The camera is in super macro or continuous shooting mode: Turn super macro and continuous shooting  
modes off (P36).  
The flash does not fire.  
The battery is exhausted: Charge the battery or insert a fully-charged spare battery (P9).  
The camera is in silent mode: Turn silent mode off (P99).  
The flash is not raised: Raise the flash (P37).  
The desired flash mode is not available in the current shooting mode: Choose a different shooting mode  
(P22).  
The camera is in silent mode: Turn silent mode off (P99).  
Some flash modes are  
not available.  
The subject is not in range of the flash: Position the subject in range of the flash (P122).  
The flash window is obstructed: Hold the camera correctly (P18).  
Fast shutter speed selected: Choose a slower shutter speed (P24, 25).  
The flash does not fully  
light the subject.  
The lens is dirty: Clean the lens (P109).  
The lens is blocked: Keep objects away from the lens (P18).  
sis displayed during shooting and the focus frame is displayed in red: Check focus before shooting  
(P115).  
Pictures are blurred.  
kis displayed during shooting: Use the flash or a tripod (P38).  
112  
Problems and Solutions  
Problem  
Solluution  
A slow shutter speed is selected at high temperatures: This is normal and does not indicated a mal-  
function.  
The camera has been used continuously at high temperatures or a temperature warning is displayed: Turn  
the camera off and wait for it to cool down.  
Pictures are mottled.  
LCD monitor displays  
nothing.  
Display mode is set to LCD SWITCHED OFF: Press DISP/BACK to choose a different display mode (P6).  
Sounds made by the  
camera are recorded with Intelligent Face Detection is on: Turn Intelligent Face Detection off (P53).  
movies.  
Playback  
Problem  
Solluution  
Pictures are grainy.  
The pictures were taken with a different make or model of camera.  
Playback zoom unavail-  
able.  
The picture has been saved at a, or is from another make or model of camera (P58).  
The camera is in silent mode: Turn silent mode off (P99).  
No sound in voice memo Playback volume is too low: Adjust playback volume (P102).  
and movie playback.  
The microphone was obstructed: Hold the camera correctly during recording (P2).  
The speaker is obstructed: Hold the camera correctly during playback (P2).  
Selected pictures are not Some of the pictures selected for deletion are protected. Remove protection using the device  
deleted. with which it was originally applied (P94).  
File numbering is unex- The battery-chamber cover was opened while the camera was on. Turn the camera off before  
pectedly reset. opening the battery-chamber cover (P15).  
113  
Problems and Solutions  
Connections/Miscellaneous  
Problem  
Solluution  
The camera is not properly connected: Connect the camera properly (P69).  
An A/V cable was connected during movie playback: Connect the camera once movie playback has  
ended.  
No picture or sound.  
Input on the television is set to “TV”: Set input to “VIDEO”.  
The camera is not set to the correct video standard: Match the camera QVIDEO SYSTEM setting to  
the TV (P106).  
The volume on the TV is too low: Adjust the volume.  
No color  
Match the camera QVIDEO SYSTEM setting to the TV (P106).  
The computer does not  
recognize the camera.  
Be sure the camera and computer are correctly connected (P81).  
Can not transfer RAW or  
JPEG files to computer.  
Use the bundled software to transfer pictures (P77).  
Pictures can not be  
printed.  
The camera is not properly connected: Connect the camera correctly (P71).  
The printer is off: Turn the printer on.  
Only one copy is printed/  
the date is not printed.  
The printer is not PictBridge compatible.  
The camera is unrespon- Temporary camera malfunction: Remove and reinsert the battery (P10).  
sive.  
The battery is exhausted: Charge the battery (P9) or insert a fully-charged spare battery (P10).  
The camera does not  
function as expected.  
Remove and reinsert the battery (P10). If the problem persists, contact your FUJIFILM dealer.  
No sound.  
Turn silent mode off (P99).  
114  
Warning Messages and Displays  
The following warnings are displayed in the LCD monitor:  
Warning  
Description  
B(red)  
A(blinks red)  
k
Low battery. Charge the battery (P9) or insert a fully-charged spare battery (P10).  
Battery exhausted. Charge the battery (P9) or insert a fully-charged spare battery (P10).  
Slow shutter speed. Pictures may be blurred; use the flash or a tripod.  
The camera can not focus. Try one of the following solutions:  
• Use focus lock to focus on another subject at the same distance, then recompose the picture  
(P34).  
s
(displayed in red with red  
focus frame)  
• Use macro mode to focus when taking close-ups (P36).  
Aperture or shutter  
The subject is too bright or too dark and the picture will be over- or under-exposed. If the subject  
speed displayed in red is dark, use the flash (P37).  
FOCUS ERROR  
TURN OFF THE CAMERA AND Camera malfunction. Turn the camera off and then on again. If the message persists, contact a  
TURN ON AGAIN  
FUJIFILM dealer.  
LENS CONTROL ERROR  
The memory card or internal memory is not formatted or the memory card was formatted in a computer or  
other device: Format the memory card or internal memory using the KFORMAT option in the  
camera setup menu (P100).  
The memory card contacts require cleaning: Clean the contacts with a soft, dry cloth. If the message  
is repeated, format the card (P100). If the message persists, replace the card.  
Camera malfunction: Contact a FUJIFILM dealer.  
CARD NOT INITIALIZED  
PROTECTED CARD  
BUSY  
The memory card is locked. Unlock the card (P12).  
The memory card is incorrectly formatted. Use the camera to format the card (P100).  
115  
Warning Messages and Displays  
Warning  
Description  
Turn the camera off and wait for it to cool. If no action is taken, the camera will turn off automati-  
cally.  
p
The memory card is not formatted for use in the camera. Format the card (P100).  
The memory card contacts require cleaning or the memory card is damaged. Clean the contacts  
with a soft, dry cloth. If the message is repeated, format the card (P100). If the message persists,  
replace the card.  
CARD ERROR  
Incompatible memory card. Use a compatible card (P14).  
Camera malfunction. Contact a FUJIFILM dealer.  
aMEMORY FULL  
bMEMORY FULL  
INTERNAL MEMORY IS FULL  
INSERT A NEW CARD  
The memory card or internal memory is full and pictures can not be recorded or copied. Delete  
pictures or insert a memory card with more free space.  
Memory card error or connection error: Reinsert the card or turn the camera off and then on again.  
If the message persists, contact a FUJIFILM dealer.  
Not enough memory remaining to record additional pictures: Delete pictures or insert a memory card  
with more free space.  
The memory card or internal memory is not formatted: Format the memory card or internal memory  
(P100).  
The file is corrupt or was not created with the camera: The file can not be viewed.  
The memory card contacts require cleaning: Clean the contacts with a soft, dry cloth. If the message  
is repeated, format the card (P100). If the message persists, replace the card.  
Camera malfunction: Contact a FUJIFILM dealer.  
WRITE ERROR  
READ ERROR  
116  
Warning Messages and Displays  
Warning  
Description  
The camera has run out of frame numbers (current frame number is 999-9999). Format the memo-  
ry card and select RENEW for BFRAME NO. Take a picture to reset frame numbering to 100-0001,  
then select CONTINUOUS for BFRAME NO. (P101).  
FRAME NO. FULL  
PRESS AND HOLD  
THE DISP BUTTON TO  
DEACTIVATE SILENT MODE  
An attempt was made to choose a flash mode or adjust the volume with the camera in silent mode.  
Exit silent mode before choosing a flash mode or adjusting the volume (P20).  
A search has returned more than 30,000 results: Choose a search that returns fewer results.  
More than 999 images are selected for deletion: Choose fewer images.  
An attempt was made to delete, rotate, or add a voice memo to a protected picture. Remove  
protection and try again (P94).  
TOO MANY FRAMES  
PROTECTED FRAME  
aCAN NOT CROP  
CAN NOT CROP  
apictures can not be cropped.  
The picture is damaged or was not created with the camera.  
PCANNOT EXECUTE  
QCANNOT EXECUTE  
aCANNOT EXECUTE  
CAN NOT ROTATE  
FCAN NOT ROTATE  
mCANNOT EXECUTE  
FCANNOT EXECUTE  
An attempt was made to create a resized copy at a size equal to or larger than the original. Choose  
a smaller size.  
An attempt was made to rotate a picture that can not be rotated.  
Movies can not be rotated.  
Red-eye removal can not be applied to the selected picture.  
Red-eye removal can not be applied to movies.  
117  
Warning Messages and Displays  
Warning  
NO CARD  
Description  
No memory card inserted when ECOPY is selected. Insert a memory card.  
bNO IMAGE  
aNO IMAGE  
The source selected for ECOPY contains no images. Select a different source.  
The voice memo file is corrupt: The voice memo can not be played back.  
Camera malfunction: Contact a FUJIFILM dealer.  
uERROR  
The DPOF print order on the current memory card contains more than 999 images. Copy the  
pictures to internal memory and create a new print order.  
DPOF FILE ERROR  
CAN NOT SET DPOF  
FCAN NOT SET DPOF  
The picture can not be printed using DPOF.  
Movies can not be printed using DPOF.  
A connection error occurred while pictures were being printed or copied to a computer or other  
device. Confirm that the device is turned on and that the USB cable is connected.  
Printer out of paper or ink, or other printer error. Check printer (see printer manual for details). To  
resume printing, turn the printer off and then turn it back on.  
COMMUNICATION ERROR  
PRINTER ERROR  
PRINTER ERROR  
RESUME?  
Printer out of paper or ink, or other printer error. Check printer (see printer manual for details). If  
printing does not resume automatically, press MENU/OK to resume.  
An attempt was made to print a movie, a picture not created with the camera, or a picture in a  
format not supported by the printer. Movies and some pictures created with other devices can  
not be printed; if the picture is a still picture created with the camera, check the printer manual to  
confirm that the printer supports the JFIF-JPEG or Exif-JPEG format. If it does not, the pictures can  
not be printed.  
CANNOT BE PRINTED  
118  
Internal Memory/Memory Card Capacity  
The following table shows the recording time or number of pictures available at different image sizes.  
All figures are approximate; file size varies with the scene recorded, producing wide variations in the  
number of files that can be stored. The number of exposures or length remaining may not diminish at  
an even rate. A limited number of test pictures can be taken when no memory card is inserted.  
Medium  
Internnall memory  
(approxx. 26 MB)  
4 GB  
8 GB  
O
T
FINE  
5
7
NORMAL  
FINE  
820  
NORMAL  
1300  
1720  
2530  
3350  
4590  
5160  
FINE  
1650  
2200  
2640  
3500  
4880  
7110  
NORMAL  
2620  
3450  
5080  
6720  
9210  
O4:3  
O16:9  
P4:3  
P16:9  
Q4:3  
8
11  
16  
22  
30  
35  
1090  
1310  
1740  
2430  
3540  
8
11  
16  
23  
Q16:9  
10370  
i19201  
h12801  
f2  
12sec.  
17sec.  
42sec.  
32sec.  
65sec.  
32sec.  
38min.  
49min.  
115min.  
85min.  
172min.  
86min.  
76min.  
98min.  
232min.  
112min.  
345min.  
172min.  
Y640 × 4803  
Y320 × 2403  
Y320 × 1123  
1 Use a Gcard or better. Individual movies can not exceed 29 minutes in length.  
2 Individual movies can not exceed 115 minutes in length.  
3 Use a Gcard or better. Individual movies can not exceed 30 seconds in length.  
119  
Specifications  
System  
Model  
Digital Camera X-S1  
Effective pixels  
Image sensor  
Storage media  
File system  
12 million  
2
/
3 -in., EXR CMOS with primary color filter  
• SD/SDHC/SDXC memory cards  
• Internal memory (approx. 26MB)  
Compliant with Design Rule for Camera File System (DCF), Exif 2.3, and Digital Print Order Format  
(DPOF)  
File format  
Still pictures: Exif 2.3 JPEG (compressed); RAW (original RAF format, special-purpose software required); RAW+JPEG  
available  
Movies: MOV (H.264, stereo)  
Audio: WAV (stereo)  
Image size (pixels)  
O4 : 3: 4,000×3,000 O3 : 2: 4,000×2,664 O16 : 9: 4,000×2,248 O1 : 1: 2,992×2,992  
P4 : 3: 2,816×2,112 P3 : 2: 2,816×1,864 P16 : 9: 2,816×1,584 P1 : 1: 2,112×2,112  
Q4 : 3: 2,048×1,536 Q3 : 2: 2,048×1,360 Q16 : 9: 1,920×1,080 Q1 : 1: 1,536×1,536  
r MOTION PANORAMA v: 1,624×11,520 (tall)/11,520×1,080 (wide)  
r MOTION PANORAMA w: 1,624×5,760 (tall)/5,760×1,080 (wide)  
r MOTION PANORAMA x: 1,624×3,840 (tall)/3,840×1,080 (wide)  
r MOTION PANORAMA z: 1,624×11,520 (tall)/11,520×1,080 (wide)  
Digital zoom  
Lens  
Focal length  
About 1.4×/2× with intelligent digital zoom (up to 36.4 ×/52 × when combined with optical zoom)  
Fujinon 26×optical zoom lens, F2.8 (wide angle)–F5.6 (telephoto)  
f=6.1mm–158.6mm (35-mm format equivalent: 24 mm– 624 mm)  
F2.8–F11 (wide angle)/F5.6–F11 (telephoto) in increments of 1 3 EV  
/
Aperture  
Focus range (distance from  
front of lens)  
• Approx. 30cm (0.9ft.)–infinity (wide angle); 2m (6.5ft.)–infinity (telephoto)  
Macro: approx. 7cm–3m/0.2ft.–9.8ft. (wide angle); 2m–3.5m/6.5ft.–11.4ft. (telephoto)  
Super macro: approx. 1cm–1m/0.3in.–3.2ft. (wide angle)  
120  
Specifications  
System  
Sensitivity  
Standard output sensitivity equivalent to ISO 100, 200, 250, 320, 400, 500, 640, 800, 1000, 1250, 1600,  
2000, 2500, 3200, 4000, 5000, 64001, 128002 ; AUTO, AUTO (400), AUTO (800), AUTO (1600), AUTO (3200)  
1 image size Por Q  
2 image size Q  
Metering  
256-segment through-the-lens (TTL) metering; MULTI, SPOT, AVERAGE  
Exposure control  
Exposure compensation  
Picture stabilization  
Shutter speed (combined  
mechanical and electronic  
shutter)  
Programmed AE (with program shift), shutter-priority AE, aperture-priority AE, and manual exposure  
2EV+2EV in increments of 1 3 EV (except B, R, M, and U)  
/
Optical stabilization (lens-shift type)  
1
/
30s4,000 s  
1
1
O: 1 4 s– 1,000 s  
H: 3s 1,000 s  
/
1
/
/
/
U: 4s 2 s  
*
1
1
/
/
P: 4s 4,000 s  
S, A, M: 30s – 4,000 s (* slow speeds may not be available at high sensitivities)  
Other modes: 1 4 s– 4,000 s  
1
/
/
Continuous  
I: max. 200 frames; frame rate can be selected from 10, 7, 5, and 3 fps (The frame rate varies depending on the  
shooting conditions or numbers of frames in continuous shooting.)  
P: 16 or 8 frames (RAW+JPEG/RAW: max. 8 frames); frame rate can be selected from 10, 7, 5, and 3 fps  
O: 3 frames (selected exposure, overexposure, underexposure)  
W: 3 frames (selected sensitivity, sensitivity raised, sensitivity lowered)  
X: 3 frames (PROVIA, Velvia, ASTIA)  
Y: 3 frames (100%, 200%, 400%)  
Focus  
Mode: Single AF, continuous AF, manual focus  
Focus-area selection: Multi, area, tracking  
Autofocus system: Contrast-detect TTL AF with AF-assist illuminator  
Automatic scene detection; 7 manual preset modes for direct sunlight, shade, daylight fluorescent,  
warm white fluorescent, cool white fluorescent, incandescent lighting, color temperature; custom  
white balance  
White balance  
Self-timer  
Off, 2sec., 10sec.; auto shutter release (n)  
121  
Specifications  
System  
Flash  
Manual pop-up flash; effective range when sensitivity is set to AUTO (800) is approx. 30cm–8.0m/0.9ft.–  
26.2ft. (wide angle), 2.0m–4.0m/6.5ft.13.1ft. (telephoto)  
Flash modes  
Auto, forced flash, off, slow synchro (red-eye removal off); auto with red-eye removal, forced flash with  
red-eye removal, off, slow sync with red-eye removal (red-eye removal on)  
Electronic viewfinder  
Monitor  
0.47-in., 1440k-dot color LCD viewfinder; frame coverage approx. 100%  
3.0-in., 460k-dot color LCD monitor; frame coverage approx. 100%  
Movies  
i1920: 1,920×1,080 (1080p), 30 fps  
f: 640×480 (VGA), 30 fps  
Y320 × 240: 320×240, 120 fps  
h1280: 1,280×720 (720p), 30 fps  
Y640 × 480: 640×480, 70 fps  
Y320 × 112: 320×112, 200 fps  
Note: i, h, and fmovies are recorded with stereo sound.  
Languages  
Arabic, Bulgarian, Simplified Chinese, Traditional Chinese, Czech, Danish, Dutch, English, Farsi, Finnish,  
French, German, Greek, Hebrew, Hungarian, Indonesian, Italian, Japanese, Kazakh, Korean, Latvian,  
Lithuanian, Norwegian, Polish, Portuguese, Romanian, Russian, Serbian, Slovak, Spanish, Swedish,  
Thai, Turkish, Ukrainian, Vietnamese  
Input/output terminals  
A/V OUT (audio/video output) NTSC or PAL output with monaural sound  
HDMI output  
HDMI Mini Connector  
Digital input/output  
Connector for external  
microphone  
USB 2.0 High-Speed; shares A/V OUT connector; MTP/PTP  
φ3.5 mm  
122  
Specifications  
Power supply/other  
Power sources  
NP-95 rechargeable battery  
Battery type  
NP-95 (type supplied with camera)  
Battery life (approximate num-  
ber of frames that can be taken  
with a fully-charged battery)  
Appproxximaate number of fframes  
Appproximaate number of frames  
460  
500 (EVF)  
CIPA standard, measured in B(auto) mode using battery supplied with camera and SD memory card.  
Note: Number of shots that can be taken with battery varies with battery charge level and will decline  
at low temperatures.  
Camera dimensions  
135mm×107mm×149mm/5.3in. ×4.2in. ×5.8in. (W × H × D), excluding projections  
(minimum depth 141 mm/5.5 in.)  
Shooting weight  
Camera weight  
Approx. 945g/33.3oz., including batteries and memory card  
Approx. 905g/31.9oz., excluding batteries, accessories, and memory cards  
Operating conditions  
Temperature: 0°C+40°C/+32°F+104°F  
Humidity: 10%80% (no condensation)  
123  
Specifications  
NP-95 rechargeable battery  
Nominal voltage  
DC 3.6V  
Nominal capacity  
1800 mAh  
Operating temperature  
Dimensions (W × H × D)  
Weight  
0°C+40°C/+32°F+104°F  
35.2mm×49.5mm×10.8mm/1.3in. ×1.9in. ×0.4in.  
Approx. 39g/1.3oz.  
BC-65N battery charger  
Rated input  
100V–240V AC, 50/60Hz  
Input capacity  
15 VA  
Rated output  
4.2V DC, 650mA  
Supported batteries  
Operating temperature  
Charging time  
Dimensions (W × H × D)  
Weight  
NP-95 rechargeable batteries  
0°C+40°C/+32°F+104°F  
Approx. 210 minutes (+20 °C/+68 °F)  
65mm×25.3mm×80mm/2.5in. ×0.9in. ×3.1in., excluding projections  
Approx. 59g/2.0oz., excluding battery  
Weight and dimensions vary with the country or region of sale.  
124  
Specifications  
Color Television Systems  
NTSC (National Television System Committee) is a color television telecasting specification adopted mainly in the  
U.S.A., Canada, and Japan. PAL (Phase Alternation by Line) is a color television system adopted mainly in European  
countries and China.  
Notices  
• Specifications subject to change without notice; for the latest information, visit http://www.fujifilm.com/products/  
digital_cameras/index.html. FUJIFILM shall not be held liable for damages resulting from errors in this manual.  
• Although the monitor is manufactured using advanced high-precision technology, small bright points and  
anomalous colors (particularly in the vicinity of text) may appear. This is normal for this type of monitor and  
does not indicate a malfunction; images recorded with the camera are unaffected.  
• Digital cameras may malfunction when exposed to strong radio interference (e.g., electric fields, static electric-  
ity, or line noise).  
• Due to the type of lens used, some distortion may occur at the periphery of images. This is normal.  
125  
Restrictions on Camera Settings  
Shooting Mode and Camera Settings  
The options available in each shooting mode are listed below.  
E
Adv.  
U B i j r  
SP  
D h Z l m M N O H p Q R s U V W F  
R
S
T
P
S
A
M
C
1
1
1
1
1
1
1
1
1
OFF  
F
✔ ✔1  
✔ ✔1  
1
1
F
G
AUTO  
N
✔ ✔1  
✔ ✔1  
B
OFF  
ON  
O
✔ ✔1  
1
1
1
1
1
P
✔ ✔1 ✔ ✔1  
✔ ✔1  
✔ ✔1  
N4  
K
L
M
✔ ✔1  
B
✔ ✔1  
1
1
1
P
✔ ✔1 ✔ ✔1  
✔ ✔1  
S/R  
n
h
P
J
K
O
I
P
O
W
X
Y
✔ ✔8  
126  
Restrictions on Camera Settings  
E
Adv.  
U B i j r  
SP  
D h Z l m M N O H p Q R s U V W F  
R
S
T
P
S
A
M
C
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
AUTO  
AUTO (32200)  
AUTO (11600)  
AUTO ((800)  
AUTO ((400)  
12800  
6400  
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔  
5000  
4000  
3200  
2500  
/
2000  
N
1600  
1250  
1000  
800  
640  
500  
400  
320  
250  
200  
100  
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
o
✔ ✔1  
✔ ✔1  
5
p
q
127  
Restrictions on Camera Settings  
E
Adv.  
U B i j r  
SP  
D h Z l m M N O H p Q R s U V W F  
R
S
T
P
S
A
M
C
1
AF-C  
AF-S  
MF 7  
AUTO  
O
✔ ✔1  
1
1
O
P
✔ ✔1  
Q
T
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
AUTO  
A
B
C
D
M
c
✔ ✔1  
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔  
1
1
U
d
e
b
P
e
d
f
f
d
f
H
r
s
h
R
128  
Restrictions on Camera Settings  
E
Adv.  
U B i j r  
SP  
D h Z l m M N O H p Q R s U V W F  
R
S
T
P
S
A
M
C
Z
b
2
2
1
2
1
3
1
3
1
3
1
✔ ✔1  
✔ ✔3  
✔ ✔1  
✔ ✔2  
✔ ✔3  
✔ ✔3  
s
t
x
F6  
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
n
i1920  
h1280  
f
W
k640×480  
k320×240  
k320×112  
I
g
K
1
L
l
L
M
m
✔ ✔1  
✔ ✔3  
1
OFF  
✔ ✔3  
3
3
3
C
j
3
✔ ✔3  
✔ ✔3  
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
✔ ✔3  
✔ ✔3  
1 Optimized for selected shooting mode.  
2 ON selected automatically.  
3 OFF selected automatically.  
4 Flash disabled in all shooting modes if lowered.  
5 o (MULTI) selected automatically when Intelligent Face Detection is on.  
6 Camera focuses on faces when Intelligent Face Detection is on.  
7 Intelligent Face Detection turns off automatically in manual focus mode.  
8 Fixed at settings before recording a movie.  
129  
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN  
http://www.fujifilm.com/products/digital_cameras/index.html  
Please contact your local distributor for repairs and technical support. (see Worldwide  
Network list)  

Apple XL DH259P User Manual
Audiovox AVXMTGHR1D User Manual
Directed Video HVM580 User Manual
Eclipse Fujitsu Ten Car Video System CD3000 User Manual
Eclipse Fujitsu Ten CD8445 User Manual
Euro Pro X9191H EP91 User Manual
Home Automation 62A00 1 User Manual
JVC Camcorder LYT2340 002A M User Manual
JVC Everio GZ MG750BU User Manual
JVC GR FXM393 User Manual