FujiFilm 16082969 User Manual

For Your Safety  
Power Lines: An outside antenna sys-  
tem should not be located in the  
vicinity of overhead power lines or  
other electric light or power circuits,  
or where it can fall into such power  
lines or circuits. When installing an  
outside antenna system, extreme  
care should be taken to keep from  
touching such power lines or circuits  
as contact with them might be fatal.  
Replacement Parts: When replace-  
ment parts are required, be sure  
the service technician has used  
replacement parts specified by the  
manufacturer or have the same  
characteristics as the original part.  
Unauthorized substitutions may  
result in fire, electric shock or other  
hazards.  
Use  
Service  
Cleaning: Unplug this video product Servicing: Do not attempt to service  
from the wall outlet before clean- this video product yourself as open-  
ing. Do not use liquid cleaners or ing or removing covers may expose  
aerosol cleaners. Use a damp cloth you to dangerous voltage or other  
for cleaning.  
hazards. Refer all servicing to quali-  
fied service personnel.  
Object and Liquid Entry: Never push  
objects of any kind into this video Damage Requiring Service: Unplug this  
product through openings as they video product from the wall outlet  
may touch dangerous voltage and refer servicing to qualified ser-  
points or short out parts that could vice personnel under the following  
result in a fire or electric shock. Never conditions:  
Safety Check: Upon completion of any  
service or repairs to this video prod-  
uct, ask the service technician to  
perform safety checks to determine  
that the video product is in proper  
operating condition.  
EXAMPLE OF ANTENNA GROUNDING  
AS PER NATIONAL ELECTRICAL CODE  
spill liquid of any kind on the video When the power-supply cord or  
product.  
Ground Clamp  
Antenna  
plug is damaged.  
Lead in Wire  
If liquid has been spilled, or objects  
have fallen into the video product.  
If the video product has been ex-  
posed to rain or water.  
If the video product has been  
dropped or the cabinet has been  
damaged.  
If the video product does not op-  
erate normally be following the  
operating instructions. Adjust only  
those controls that are covered by  
the operating instructions as an im-  
proper adjustment of other controls  
may result in damage and will often  
require extensive work by a qualified  
technician to restore the video prod-  
uct to its normal operation.  
Lightning: For added protection for  
this video product receiver during  
a lightning storm, or when it is left  
unattended and unused for long pe-  
Electric  
Service  
Equipment  
Antenna  
Discharge Unit riods of time, unplug it from the wall  
(NEC SECTION  
810-20)  
Grounding  
Conductors  
(NEC SECTION  
810-21)  
Ground  
Clamps  
outlet and disconnect the antenna  
or cable system. This will prevent  
damage to the video product due to  
lightning and power-line surges.  
Power Service  
Grounding Electrode  
System (NEC ART 250.  
PART H)  
When the video product exhibits a  
distinct change in performance - this  
indicates a need for service.  
iii  
For Your Safety  
Be sure to read this notes before using  
Safety Notes  
WARNING  
Do not allow water or foreign objects to enter the camera.  
If water or foreign objects get inside the camera, turn the camera  
off, remove the battery and disconnect and unplug the AC power  
adapter.  
• Make sure that you use your camera correctly. Read these Safety Notes and  
your Owner’s Manual carefully before use.  
Continued use of the camera can cause a fire or electric shock.  
• Contact your FUJIFILM dealer.  
• After reading these Safety Notes, store them in a safe place.  
About the Icons  
Do not use the camera in the bathroom or shower.  
This can cause a fire or electric shock.  
The icons shown below are used in this document to indicate the severity of  
the injury or damage that can result if the information indicated by the icon  
is ignored and the product is used incorrectly as a result.  
Do not use in  
the bathroom  
or shower.  
Never attempt to disassemble or modify (never open the case).  
Failure to observe this precaution can cause fire or electric shock.  
This icon indicates that death or serious injury can result if the infor-  
mation is ignored.  
Do not disas-  
semble  
WARNING  
Should the case break open as the result of a fall or other accident, do not  
touch the exposed parts.  
Failure to observe this precaution could result in electric shock or in  
injury from touching the damaged parts. Remove the battery im-  
mediately, taking care to avoid injury or electric shock, and take the  
product to the point of purchase for consultation.  
This icon indicates that personal injury or material damage can result  
if the information is ignored.  
CAUTION  
Do not touch  
internal  
parts  
The icons shown below are used to indicate the nature of the information  
which is to be observed.  
Triangular icons tell you that this information requires attention (“im-  
portant”).  
Do not change, heat or unduly twist or pull the connection cord and do not  
place heavy objects on the connection cord.  
These actions could damage the cord and cause a fire or electric  
shock.  
• If the cord is damaged, contact your FUJIFILM dealer.  
Circular icons with a diagonal bar tell you that the action indicated is  
prohibited (“Prohibited”).  
Filled circles with an exclamation mark tell you an action that must be  
performed (“Required”).  
Do not place the camera on an unstable surface.  
This can cause the camera to fall or tip over and cause injury.  
Never attempt to take pictures while in motion.  
Do not use the camera while you are walking or driving a vehicle. This  
can result in you falling down or being involved in a traffic accident.  
Do not touch any metal parts of the camera during a thunderstorm.  
This can cause an electric shock due to induced current from the  
lightning discharge.  
WARNING  
If a problem arises, turn the camera off, remove the battery, disconnect and  
unplug the AC power adapter.  
Continued use of the camera when it is emitting smoke, is emitting  
any unusual odor, or is in any other abnormal state can cause a fire  
Unplug  
from power  
socket.  
or electric shock.  
Do not use the battery except as specified.  
Load the battery as aligned with the indicator.  
• Contact your FUJIFILM dealer.  
iv  
For Your Safety  
WARNING  
CAUTION  
Do not heat, change or take apart the battery. Do not drop or subject the bat-  
tery to impacts. Do not store the battery with metallic products. Do not use  
chargers other than the specified model to charge the battery.  
Any of these actions can cause the battery to burst or leak and cause  
fire or injury as a result.  
Do not place heavy objects on the camera.  
This can cause the heavy object to tip over or fall and cause injury.  
Do not move the camera while the AC power adapter is still connected. Do not  
pull on the connection cord to disconnect the AC power adapter.  
This can damage the power cord or cables and cause a fire or electric  
shock.  
Do not use the AC power adapter when the plug is damaged or the plug socket  
connection is loose.  
Use only the battery or AC power adapters specified for use with this camera.  
Do not use voltages other than the power supply voltage shown.  
The use of other power sources can cause a fire.  
If the battery leaks and fluid gets in contact with your eyes, skin or clothing.  
Flush the affected area with clean water and seek medical attention or call an  
emergency number right away.  
This could cause a fire or electric shock.  
Do not cover or wrap the camera or the AC power adapter in a cloth or blanket.  
This can cause heat to build up and distort the casing or cause a fire.  
Do not use the charger to charge batteries other than those specified here.  
The Ni-MH battery charger is designed for FUJIFILM HR-AA Ni-MH  
batteries. Using the charger to charge conventional batteries or other  
types of rechargeable batteries can cause the battery to leak fluid,  
overheat or burst.  
When carrying the battery, install it in a digital camera or keep it in the hard  
case. When storing the battery, keep it in the hard case. When discarding,  
cover the battery terminals with insulation tape.  
When you are cleaning the camera or you do not plan to use the camera for  
an extended period, remove the battery and disconnect and unplug the AC  
power adapter.  
Failure to do so can cause a fire or electric shock.  
When charging ends, unplug the charger from the power socket.  
Leaving the charger plugged into the power socket can cause a fire.  
Using a flash too close to a person’s eyes may temporarily affect the eyesight.  
Take particular care when photographing infants and young chil-  
dren.  
Contact with other metallic objects or battery could cause the bat-  
tery to ignite or burst.  
When a memory card is removed, the card could come out of the slot too quick-  
ly. Use your finger to hold it and gently release the card.  
Keep Memory Cards out of the reach of small children.  
Because Memory Cards are small, they can be swallowed by children.  
Be sure to store Memory Cards out of the reach of small children. If  
a child swallows a Memory Card, seek medical attention or call an  
emergency number.  
Request regular internal testing and cleaning for your camera.  
Build-up of dust in your camera can cause a fire or electric shock.  
• Contact your FUJIFILM dealer to request internal cleaning every 2  
years.  
• Please note this is not a free of charge service.  
CAUTION  
Do not use this camera in locations affected by oil fumes, steam, humidity or  
dust.  
This can cause a fire or electric shock.  
Do not leave this camera in places subject to extremely high temperatures.  
Do not leave the camera in locations such as a sealed vehicle or in  
direct sunlight. This can cause a fire.  
Keep out of the reach of small children.  
This product could cause injury in the hands of a child.  
v
For Your Safety  
If you are using a heating pad, take  
care not to place the battery di-  
rectly against the pad. The camera  
may not operate if you use a de-  
pleted battery in cold conditions.  
• Dispose of used battery promptly.  
• Do not drop the battery or other-  
wise subject it to strong impacts.  
• Do not expose the battery to wa-  
ter.  
Battery Life  
Power Supply and Battery  
At normal temperatures, the bat-  
tery can be used at least 300 times.  
If the time for which the battery  
provides power shortens markedly,  
this indicates that the battery has  
reached the end of its effective life  
and should be replaced.  
* Confirm your battery type before read-  
ing the following descriptions.  
The following explains proper use of  
batteries and how to prolong their  
• Always keep the battery terminals  
clean.  
life. Incorrect use of batteries can Charging the Battery  
cause shorter battery life, as well as • You can charge the battery using  
• Do not store batteries in hot plac-  
es. Also, if you use the battery for  
a long period, the camera body  
and the battery itself will become  
warm. This is normal. Use the AC  
power adapter if you are taking  
pictures or viewing images for a  
long period of time.  
leakage, excessive heat, fire or explo-  
sion.  
the battery charger (included).  
- The battery can be charged  
at ambient temperatures be-  
tween 0°C and +40°C (+32°F  
and +104°F). Refer to the Owner’s  
Manual for the time of charging  
battery.  
- You should charge the battery  
at an ambient temperature be-  
tween +10°C and +35°C (+50°F  
and +95°F). If you charge the  
battery at a temperature outside  
this range, charging takes longer  
because the performance of the  
battery is impaired.  
- You cannot charge the battery  
at temperatures of 0°C (+32°F) or  
below.  
• The Rechargeable Lithium-ion Bat-  
tery does not need to be fully dis-  
charged or exhausted flat before  
being charged.  
Notes on storage  
• If a battery is stored for long periods  
while charged, the performance of  
the battery can be impaired. If the  
battery will not be used for some  
time, run the battery out before  
storing it.  
• If you do not intend to use the  
camera for a long period of time,  
remove the battery from the cam-  
era.  
• Store the battery in a cool place.  
- The battery should be stored in  
a dry location with an ambient  
temperature between +15°C and  
+25°C (+59°F and +77°F).  
Camera uses the Rechargeable  
Lithium-ion Battery  
1
* When shipped, the battery is not  
fully charged. Always charge the  
battery before using it.  
* When carrying the battery, install it  
in a digital camera or keep it in the  
soft case.  
Camera uses AA-size alkaline or Ni-MH  
(nickel-metal hydride) rechargeable  
batteries  
2
Battery Features  
* For details on the batteries that  
you can use, refer to the Owner’s  
Manual of your camera.  
• The battery gradually loses its  
charge even when not used. Use  
a battery that has been charged  
recently (in the last day or two) to  
take pictures.  
Cautions for Using Battery  
• Do not heat the batteries or throw  
them into a fire.  
- Do not leave the battery in hot or  
extremely cold places.  
• To maximize the life of the battery,  
turn the camera off as quickly as  
possible when it is not being used.  
• The number of available frames will  
be lower in cold locations or at low  
temperatures. Take along a spare  
fully charged battery. You can also  
increase the amount of power pro-  
duced by putting the battery in  
your pocket or another warm place  
to heat it and then loading it into  
the camera just before you take a  
picture.  
• Do not carry or store batteries with  
metal objects such as necklaces or  
hairpins.  
• Do not expose the batteries to wa-  
ter, and keep batteries from getting  
wet or stored in moist locations.  
• Do not attempt to take apart or  
change the batteries, including  
battery casings.  
• Do not subject the batteries to  
strong impacts.  
• Do not use batteries that are leak-  
ing, deformed, discolored.  
Handling the Battery  
Cautions for Your Safety:  
• Do not carry or store battery with  
metal objects such as necklaces or  
hairpins.  
• Do not heat the battery or throw it  
into a fire.  
• Do not attempt to take apart or  
change the battery.  
• Do not recharge the battery with  
chargers other those specified.  
• The battery may feel warm after it  
has been charged or immediately  
after being used. This is perfectly  
normal.  
• Do not recharge a fully charged  
battery.  
vi  
For Your Safety  
• Do not store batteries in warm or  
humid places.  
• Keep the batteries out of reach of  
babies and small children.  
• Make sure that the battery polarity  
(C and D) is correct.  
• Do not use new with used batter-  
ies. Do not use charged and dis-  
charged batteries together.  
If any liquid at all leaks from  
the batteries, wipe the battery  
compartment thoroughly and  
then load new batteries.  
• Ni-MH batteries have  
a
limited  
CAUTION  
service life. If a battery can only  
be used for a short time even after  
repeated discharge-charge cycles,  
it may have reached the end of its  
service life.  
Do not use the “Discharging re-  
chargeable batteries” function when  
alkaline batteries being used.  
• To charge Ni-MH batteries, use the  
quick battery charger (sold sepa-  
rately). Refer to the instructions  
supplied with the charger to make  
sure that the charger is used cor-  
rectly.  
If any battery fluid comes into  
contact with your hands or  
clothing, flush the area thor-  
oughly with water. Note that  
battery fluid can cause loss  
of eyesight if it gets into your  
eyes. If this occurs, do not rub  
your eyes. Flush the fluid out  
with clean water and contact  
your physician for treatment.  
Disposing of Batteries  
• When disposing of batteries, do  
so in accordance with your local  
waste disposal regulations.  
• Do not use different types or  
brands of batteries at the same  
time.  
• Do not use the battery charger to  
charge other batteries.  
• Note that the batteries feel warm  
after being charged.  
Notes on both models (  
,
)
3
1
2
• If you do not intend to use the  
camera for a long period of time,  
remove the batteries from the  
camera. Note if the camera is left  
with the batteries removed, the  
time and date settings are cleared.  
• The batteries feel warm right af-  
ter being used. Before removing  
the batteries, turn the camera off  
and wait for the batteries to cool  
down.  
• Since batteries do not work well in  
cold weather or locations, warm  
the batteries by placing them in-  
side your garments before use.  
Batteries do not work well when  
cold. They will work again when  
the temperature returns to normal.  
• Soil (such as fingerprints) on the  
battery terminals makes the bat-  
teries charge less reducing the  
number of images. Carefully wipe  
the battery terminals with a soft  
dry cloth before loading.  
AC Power Adapter  
Always use the AC Power Adapter  
with the camera. The use of an AC  
Power adapter other than FUJIFILM  
AC Power Adapter can be damaged  
to your digital camera.  
For details on the AC power adapter,  
refer to the Owner’s Manual of your  
camera.  
• Due to the way the camera is con-  
structed, a small amount of current  
is used even when the camera is  
turned off. Note in particular that  
leaving Ni-MH batteries in the  
camera for a long period will over-  
discharge the batteries and may  
render them unusable even after  
recharging.  
• Ni-MH batteries will self-discharge  
even when not used, and the time  
for which they can be used may be  
shortened as a result.  
• Ni-MH batteries will deteriorate  
rapidly if over-discharged (e.g.  
by discharging the batteries in a  
flashlight). Use the “Discharging re-  
chargeable batteries” function pro-  
vided in the camera to discharge  
the batteries.  
Using the AA-size Ni-MH batteries  
correctly  
• Ni-MH batteries left unused in  
storage for long periods can be-  
come “deactivated”. Also, repeat-  
edly charging Ni-MH batteries  
that are only partially discharged  
can cause them to suffer from the  
“memory effect”. Ni-MH batteries  
that are “deactivated” or affected  
by “memory” suffer from the prob-  
lem of only providing power for a  
short time after being charged. To  
prevent this problem, discharge  
and recharge them several times  
using the camera’s “Discharging  
rechargeable batteries” function.  
Deactivation and memory are spe-  
cific to Ni-MH batteries and are not  
in fact battery faults.  
• Use the AC power adapter for in-  
door use only.  
• Plug the connection cord plug se-  
curely into the DC input terminal.  
• Turn off the FUJIFILM Digital cam-  
era before disconnecting the cord  
from the DC input terminal. To dis-  
connect, pull out the plug gently.  
Do not pull on the cord.  
• Do not use the AC power adapter  
with any device other than your  
camera.  
• During use, the AC power adapter  
will become hot to the touch. This  
is normal.  
See Owner’s Manual for the proce-  
dure for “Discharging rechargeable  
batteries”.  
vii  
For Your Safety  
• Do not take apart the AC power unless intended only for personal  
adapter. Doing so could be dan- use. Note that some restrictions ap-  
Trademark Information  
Explanation of Color Television  
System  
E and xD-Picture Card™ are  
trademarks of FUJIFILM Corpora-  
tion.  
• IBM PC/AT is a registered trademark  
of International Business Machines  
Corp. of the U.S.A.  
• Macintosh, QuickTime, and Mac OS  
are trademarks of Apple Inc. in the  
U.S.A. and other countries.  
• Windows 7, Windows Vista and the  
Windows logo are trademarks of  
the Microsoft group of companies.  
• IrSimple™ Trademark is owned by  
the Infrared Data Association®.  
• IrSS™ Trademark or IrSimpleShot™  
Trademark is owned by the Infra-  
red Data Association®.  
• SDHC logo is a trademark.  
• HDMI logo is a trademark.  
• YouTube is a trademark of Google  
Inc.  
NTSC: National Television System  
Committee, color television  
gerous.  
• Do not use the AC power adapter performances, entertainments and  
in a hot and humid place. exhibits, even when intended purely  
• Do not subject the AC power for personal use. Users are also asked  
adapter to strong shocks. to note that the transfer of Memory  
• The AC power adapter may emit a Card containing images or data pro-  
ply to the photographing of stage  
telecasting  
specifications  
adopted mainly in the U.S.A.,  
Canada and Japan.  
PAL: Phase Alternation by Line, a  
color television system ad-  
opted mainly by European  
countries and China.  
humming. This is normal.  
tected under copyright laws is only  
• If used near a radio, the AC power permissible within the restrictions  
adapter may cause static. If this imposed by those copyright laws.  
happens, move the camera away  
from the radio.  
Handling Your Digital Camera  
To ensure that images are recorded  
Exif Print (Exif ver. 2.3)  
Exif Print Format is a newly revised  
digital camera file format that con-  
tains a variety of shooting informa-  
tion for optimal printing.  
correctly, do not subject the camera  
to impact or shock while an image is  
being recorded.  
Before Using the Camera  
Do not aim the camera at extremely  
bright light sources, such as the sun  
Liquid Crystal  
in a cloudless sky. Failure to observe  
this precaution could damage the  
camera image sensor.  
If the LCD monitor is damaged, take  
particular care with the liquid crystal  
in the monitor. If any of the follow-  
ing situations arise, take the urgent  
action indicated.  
• If liquid crystal comes in contact  
with your skin:  
Wipe the area with  
IMPORTANT NOTICE: Read Before  
Using the Software  
Direct or indirect export, in whole or  
in part, of licensed software without  
the permission of the applicable  
governing bodies is prohibited.  
Test Shots Prior to Photography  
For important photographs (such as  
weddings and overseas trips), always  
take a test shot and view the im-  
age to make sure that the camera is  
working normally.  
• FUJIFILM Corporation cannot ac-  
cept liability for any incidental  
losses (such as the costs of photog-  
raphy or the loss of income from  
photography) incurred as a result  
of faults with this product.  
• Other company or product names  
are trademarks or registered trade-  
marks of the respective compa-  
cloth and  
nies.  
a
then wash thoroughly with soap  
and running water.  
Notes on Electrical Interference  
If the camera is to be used in hos-  
pitals or aircrafts, please note that  
this camera may cause interference  
to other equipment in the hospital  
or aircraft. For details, please check  
with the applicable regulations.  
• If liquid crystal gets into your eye:  
Flush the affected eye with clean  
water for at least 15 minutes and  
then seek medical assistance.  
• If liquid crystal is swallowed:  
Flush your mouth thoroughly with  
water. Drink large quantities of wa-  
ter and induce vomiting. Then seek  
medical assistance.  
Notes on Copyright  
Images recorded using your digital  
camera system cannot be used in  
ways that infringe copyright laws  
without the consent of the owner,  
viii  
About This Manual  
Before using the camera, read this manual and the warnings on pages ii–viii. For information on spe-  
cific topics, consult the sources below.  
Cameraa Q & A ......................................................pg. x Table of Contents .............................................pg. xiii  
Know what you want to do but don’t know the The “Table of Contents” gives an overview of the  
name for it? Find the answer in “Camera Q & A.” entire manual. The principal camera operations  
are listed here.  
Troubleshooting ...............................................pg. 89 Warning Messaageess aand DDiisplaayyss ........................pg. 96  
Having a specific problem with the camera? Find out what’s behind that flashing icon or error  
Find the answer here.  
message in the monitor.  
Gloossssaarryy .........................................................pg. 100 Resttrriiccttiioonnss oonn CCaammeerraa SSettings..............Baasic Manual  
The meanings of some technical terms may be See the Basic Manual for restrictions on the op-  
found here.  
tions available in each shooting mode.  
Memory Cards  
Pictures can be stored in the camera’s internal memory or on optional SD and SDHC memory cards. In this  
manual, SD memory cards are referred to as “memory cards.” For more information, see page 9.  
ix  
Camera Q & A  
Find items by task.  
Camera SSetup  
Quueesttion  
Key phrase  
Date and time  
See paage  
13  
How do I set the camera clock?  
Can I set the clock to local time when I travel?  
How do I keep the display from turning off automatically?  
How do I make the display brighter or darker?  
Time difference  
Auto power off  
LCD brightness  
Operation and shutter volume  
Silent mode  
81  
84  
79  
79  
How do I stop the camera beeping and clicking?  
18  
Can I change the sound the shutter makes?  
What do the icons in the display mean?  
How much charge is left in the battery?  
Shutter sound  
Displays  
Battery level  
79  
3
16  
Sharriinngg PPiiccttuurreess  
Quueesttion  
Key phrase  
See paage  
49  
55  
Can I print pictures on my home printer?  
Can I copy my pictures to my computer?  
* For information on printing C pictures, visit http://fujifilm.com/3d/print/.  
Printing pictures*  
Viewing pictures on a computer  
x
Camera Q & A  
Taking Picctures  
Quueesttion  
Key phrase  
See paage  
15  
21  
44  
How do I take C photographs?  
How do I take D photographs?  
How do I shoot movies in C or D?  
Taking C photographs  
Taking D photographs  
Recording movies  
How can I make good portraits?  
Can I choose my own settings for different scenes?  
How do I shoot close-ups?  
Intelligent Face Detection  
Scene position  
Macro mode (close-ups)  
67  
22  
34  
How do I keep the flash from firing?  
How do I stop my subjects’ eyes glowing red when I use the flash?  
How do I “fill-in” shadows on back-lit subjects?  
How do I take a series of pictures in a single burst?  
How do I take a group portrait that includes the photographer?  
Can I choose shutter speed or aperture?  
Flash mode  
35  
Continuous mode  
Self-timer mode  
P, A, and M modes  
66  
37  
24–26  
xi  
Camera Q & A  
Viewingg PPiiccttuurreess  
Quueesttion  
Key phrase  
See paage  
How do I switch between C and D views?  
How do I view C pictures?  
How do I view D pictures?  
How do I view my pictures?  
How do I delete the current picture?  
Can I select other pictures for deletion?  
Can I zoom in on pictures during playback?  
How do I view a lot of pictures at once?  
How do I view all pictures taken on the same day?  
Can I protect my pictures from accidental deletion?  
Can I hide the icons in the display when viewing my pictures?  
Switching between C and D  
Viewing C pictures  
Viewing D pictures  
Single-frame playback  
The bbutton  
39  
20  
21  
39  
20  
42  
40  
41  
41  
72  
39  
Deleting pictures  
Playback zoom  
Multi-frame playback  
Sort by date  
Protect  
Choosing a display format  
xii  
Table of Contents  
For Your Safety ................................................................................. ii  
About This Manual......................................................................... ix  
Camera Q & A..................................................................................... x  
More on PPhotoography  
Shooting Mode...............................................................................22  
B AUTO ..........................................................................................22  
SP1/SP2 SCENE POSITION........................................................22  
M MANUAL .....................................................................................24  
A APERTURE PRIORITY AE.........................................................25  
P PROGRAM AE.............................................................................26  
I ADVANCED 2D ...................................................................27  
V TELE/WIDE ............................................................................28  
X 2-COLOR.................................................................................28  
W 2-SENSITIVITY.......................................................................28  
H ADVANCED 3D ...................................................................29  
A INDIVID. SHUTTER 3D .......................................................30  
B INTERVAL 3D SHOOTING.................................................31  
Focus Lock ........................................................................................32  
F Macro Mode (Close-ups) ......................................................34  
N Using the Flash (Super Intelligent Flash) .......................35  
hUsing the Self-Timer...............................................................37  
Beffore You Beggiin  
Introduction....................................................................................... 1  
Symbols and Conventions.......................................................... 1  
Supplied Accessories.................................................................... 1  
Parts of the Camera....................................................................... 2  
Camera Displays .......................................................................... 3  
The Mode Dial .............................................................................. 4  
First Steps  
Charging the Battery ..................................................................... 5  
Inserting the Battery...................................................................... 6  
Inserting a Memory Card............................................................. 9  
Turning the Camera on and Off...............................................12  
Shooting Mode.............................................................................12  
Playback Mode..............................................................................12  
Basic Setup .......................................................................................13  
Moorree on PPllayback  
Playback Options...........................................................................39  
Playback Zoom..............................................................................40  
Multi-Frame Playback.................................................................41  
Sort by Date....................................................................................41  
ADeleting Pictures....................................................................42  
Basic Photograpphy andd Playback  
Taking C Pictures in Auto Mode .........................................15  
Viewing C Pictures....................................................................20  
Shooting and Viewing D Pictures......................................21  
Taking Pictures in D.................................................................21  
Viewing Pictures in D..............................................................21  
xiii  
Table of Contents  
Movies  
Menus  
FRecording Movies...................................................................44  
aViewing Movies .......................................................................46  
Using the Menus: Shooting Mode .........................................60  
Using the Shooting Menu.........................................................60  
Shooting Menu Options............................................................61  
NISO............................................................................................63  
OIMAGE SIZE............................................................................64  
TIMAGE QUALITY ..................................................................65  
PFINEPIX COLOR....................................................................65  
DWHITE BALANCE.................................................................66  
RCONTINUOUS.......................................................................66  
bFACE DETECTION (D Only)..........................................67  
CPHOTOMETRY......................................................................68  
F2D AF MODE (D Only) ...................................................68  
Using the Menus: Playback Mode..........................................69  
Using the Playback Menu .........................................................69  
Playback Menu Options.............................................................69  
iPARALLAX CONTROL (C Only)...................................70  
ISLIDE SHOW .........................................................................70  
BRED EYE REMOVAL (D Only) .......................................71  
DPROTECT ................................................................................72  
GCROP........................................................................................73  
ORESIZE .....................................................................................74  
CIMAGE ROTATE (D Only)...............................................75  
ECOPY........................................................................................76  
Connections  
Viewing Pictures on TV...............................................................47  
Viewing Pictures on a 3D TV.....................................................48  
Printing Pictures via USB (D Only) .....................................49  
Connecting the Camera ............................................................49  
Printing Selected Pictures ........................................................50  
Printing the DPOF Print Order ................................................52  
Creating a DPOF Print Order....................................................53  
Viewing Pictures on a Computer............................................55  
Installing the Software...............................................................55  
Connecting the Camera ............................................................57  
xiv  
Table of Contents  
The Setup Menu.............................................................................78  
Using the Setup Menu ...............................................................78  
Setup Menu Options...................................................................79  
NTIME DIFFERENCE...............................................................81  
KFORMAT..................................................................................82  
AIMAGE DISP. ..........................................................................82  
BFRAME NO.............................................................................83  
wHDMI OUTPUT .....................................................................83  
MAUTO POWER OFF..............................................................84  
DDIGITAL ZOOM (D Only)...............................................84  
qOPT AXIS CONTROL...........................................................85  
o3DREC .....................................................................................85  
r3D CAUTION DISP ..............................................................85  
Techniccal Notees  
Optional Accessories ...................................................................86  
Accessories from FUJIFILM.......................................................87  
Caring for the Camera.................................................................88  
Troublesshootinng  
Troubleshooting ............................................................................89  
Warning Messages and Displays............................................96  
Appendix  
Glossary .......................................................................................... 100  
Internal Memory/Memory Card Capacity....................... 102  
Specifications............................................................................... 103  
xv  
3 Caution: Using the FinePix REAL 3D W3  
D display is recommended for young children (up to the age of about six) whose visual system is still maturing  
and for individuals with notable differences in vision between their two eyes, who may find it difficult or impos-  
sible to observe the C effect. Should you experience fatigue or discomfort while viewing C images, cease use  
immediately. A ten-minute break is recommended about once every half hour. Switch to D immediately if C  
images still appear double after you have adjusted parallax. Individuals with a history of photosensitive epilepsy  
or heart disease or who are unwell or suffering from fatigue, insomnia, or the affects of alcohol should refrain from  
viewing C images. Viewing C images while in motion may cause fatigue or discomfort.  
To avoid adverse effects on vision, images displayed on HDMI devices should be viewed from a distance equal to  
at least twice the width of the screen, and the screen should be no larger than 65 in. Select D when viewing  
images on displays larger than 65 in.  
File Formats  
C pictures are recorded in one of two new formats: multi-picture format for photographs (pg. 20, 100) and 3D  
movie format for movies (pg. 44, 100). D images are recorded in existing formats.  
xvi  
Introduction  
Symbols and Conventions  
The following symbols are used in this manual:  
3 Caution: This information should be read before use to ensure correct operation.  
1Note: Points to note when using the camera.  
2 Tip: Additional information that may be helpful when using the camera.  
Menus and other text in the camera monitor are shown in bold. In the illustrations in this manual, the  
monitor display may be simplified for explanatory purposes.  
Supplied Accessories  
The following items are included with the camera:  
CD-ROM  
NP-50 rechargeable battery  
BC-45W battery charger  
USB cable  
Attaching the Strap  
Attach the strap as shown.  
Basic Manual  
• Strap  
3 Caution  
To ensure that you do not drop the camera,  
wear the strap on your wrist.  
1
Introduction  
Parts of the Camera  
For more information, refer to the page listed to the right of each item.  
Selector button  
Move cursor up  
m(monitor brightness) button (see below)  
b(delete) button (pg. 20)  
Move cursor left  
F (macro) button  
(pg. 34)  
Move cursor right  
N (fl a s h ) button  
(pg. 35)  
Move cursor down  
MENU/OK button (pg. 13)  
h(self-timer) button (pg. 37)  
1
2
3
Zoom control..............................16, 40, 45 10 Monitor............................................................. 3 20 DISP (display)/BACK button................17, 39  
Shutter button...........................................19 11 a(playback) button..........................20, 39 21 Battery-chamber cover.......................... 6  
Flash..................................................................35 12 Indicator lamp............................................19 22 Tripod mount  
4 Q(parallax) control ..................................15 13 Mode dial........................................................ 4 23 HDMI mini connector ...........................48  
5
6
7
8
9
Left lens  
Right lens  
14 F(movie/photo) button........................... 44 24 USB and A/V connector........47, 49, 57  
15 Strap eyelet.................................................... 1 25 Battery chamber..................................6, 10  
Microphone................................................ 44 16 Terminal cover.....................47, 48, 49, 57 26 Battery latch ............................................. 6, 7  
On/off switch and lens cover ...........12 17 C mode indicator................................15 27 Memory card slot.....................................10  
Illuminator  
18 3D (C/D) button .........15, 21, 39, 44  
Self-timer lamp..........................................38 19 Speaker...........................................................46  
2 Tip: Monitor Brightness  
Pressing the mbutton briefly increases monitor brightness, making the display easier to see in bright light. Nor-  
mal brightness is restored when a photograph is taken.  
2
Introduction  
Camera DDiissplaayys  
The following indicators may appear during shooting and playback:  
Shoooting  
1
2
3
4
5
6
7
Internal memory indicator* ................. 9 13 Focus frame.........................................18, 68  
Focus warning ...................................18, 96 14 Date and time.....................................13, 79  
Blur warning........................................35, 96 15 Number of available frames...........102  
Silent mode indicator............................18 16 Sensitivity......................................................63  
Continuous mode ...................................66 17 Image quality/size............................64, 65  
Metering........................................................68 18 Bright monitor indicator........................ 2  
M
9
800  
N
3D  
12/31/2050 10:00 AM  
12  
02  
Intelligent Face Detection  
19 FINEPIX color...............................................65  
-
50  
F5  
3
indicator.........................................................67 20 White balance............................................66  
Shooting mode.........................................61 21 Battery level.................................................16  
Flash mode...................................................35 22 Parallax display...........................................15  
8
9
* a: indicates that no memory card  
is inserted and that pictures will  
be stored in the camera’s internal  
memory (pg. 9).  
10 Macro (close-up) mode.............................34 23 Lens obstruction warning..................96  
11 Self-timer indicator.................................37 24 Exposure compensation.....................61  
12 C/D mode indicator  
......................................................15, 21, 39, 44  
Playback  
1
2
3
4
Gift image.....................................................39  
Silent mode indicator............................18 8 C/D mode indicator  
Red-eye removal indicator ................71  
Intelligent Face Detection  
7
DPOF print indicator..............................54  
100-0001  
800  
3D  
......................................................15, 21, 39, 44  
9 C image .....................................................20  
4:3  
N
indicator.................................................40, 71 10 Frame number...........................................83  
Playback mode indicator............20, 39 11 Parallax display...........................................15  
Protected image.......................................72  
5
6
12/31/2050 10:00 AM  
02  
-
12  
50  
F5  
3
3
Introduction  
Thee MMooddee DDiiaall  
To select a shooting mode, align the mode icon with the mark next to the  
mode dial.  
I (ADVANCED 2D): Use the left and right  
lens to take two D photos simultane-  
ously with different settings applied to  
each (pg. 27).  
H (ADVANCED 3D): Take two pictures  
with the left lens for greater freedom in  
framing C photos (pg. 29).  
B
(AUTO):  
A
simple “point-and-shoot”  
P, A, M: Select for full control over camera  
settings, including aperture (M and A)  
and/or shutter speed (M; pg. 24).  
mode recommended for first-time users  
of digital cameras (pg. 15).  
SP1, SP2 (SCENE POSITION): Choose  
a
scene suited to the subject or shooting  
conditions and let the camera do the rest  
(pg. 22).  
4
Charging the Battery  
The battery is not charged at shipment. Charge the battery before use.  
Plug the charger in.  
Plug the charger into a power outlet. The  
charging indicator will light.  
Batteries  
2
The camera uses an NP-50 rechargeable battery.  
Place the battery in the charger.  
1
The Charging Indicator  
The charging indicator shows battery charge  
status as follows:  
Insert the battery into the supplied battery  
charger as shown, making sure that the bat-  
tery is in the orientation indicated by the  
CBD label.  
Chaarrginng inndiicator Batttteerryy sstaatuus  
Action  
Insert the  
battery.  
Battery not  
inserted.  
Battery fully Remove the  
Battery  
Off  
Charge lamp  
Arrow  
charged.  
battery.  
Battery  
charging.  
On  
Unplug the  
charger and  
remove the  
battery.  
DFC label  
Blinks  
Battery fault.  
DFC label  
Battery charger  
3 Cautions  
Charge the battery.  
• Unplug the charger when it is not in use.  
• Remove dirt from the battery terminals with a  
clean, dry cloth. Failure to observe this precau-  
tion could prevent the battery from charging.  
• Charging times increase at low temperatures.  
3
Remove the battery when charging is com-  
plete. See page 106 for information on  
charging times.  
5
Inserting the Battery  
Insert the battery in the camera as described below.  
Open the battery-chamber cover.  
Insert the battery.  
Align the orange stripe  
on the battery with the  
1
2
orange battery latch  
and slide the battery  
into the camera, keep-  
ing the battery latch pressed to one side.  
Confirm that the battery is securely latched.  
1Note  
Be sure the camera is off before opening the bat-  
tery-chamber cover.  
3 Cautions  
• Do not open the battery-chamber cover when  
the camera is on. Failure to observe this pre-  
caution could result in damage to image files or  
memory cards.  
• Do not use excessive force when handling the  
battery-chamber cover.  
Orange stripe  
Battery latch  
3 Caution  
Insert the battery in the correct orientation. Do  
NOT use force or attempt to insert the battery up-  
side down or backwards. The battery will slide in  
easily in the correct orientation.  
6
Inserting the Battery  
3 Cautions  
Close the battery-chamber cover.  
3
• Do not affix stickers or other objects to the battery.  
Failure to observe this precaution could make it im-  
possible to remove the battery from the camera.  
• Do not short the battery terminals. The battery could  
overheat.  
• Read the cautions on page vi.  
Removing the Battery  
• Use only batteries designated for use with this cam-  
era. Failure to observe this precaution could result in  
product malfunction.  
• Do not remove the labels from the battery or attempt  
to split or peel the outer casing.  
After turning the camera off,  
open the battery-chamber cover,  
press the battery latch to the  
side, and slide the battery out of  
the camera as shown.  
• The battery gradually loses its charge when not in  
use. Charge the battery one or two days before use.  
Battery latch  
3 Caution  
Turn the camera off before removing the battery.  
7
Inserting the Battery  
2 Tips: Using an AC Power Adapter  
• The camera can be powered by an optional AC power adapter and DC coupler (sold separately). Lift up and  
rotate the cover for the DC coupler cable channel as shown and the insert the DC coupler into the battery  
chamber, making sure that the DC coupler cable passes through the cable channel. See the manuals provided  
with the AC power adapter and DC coupler for details.  
Cover for DC coupler cable  
channel  
• If the camera is powered by an AC power adapter, demo mode slides will be displayed when the camera is  
turned on. Press the shutter-release button halfway to cancel demo mode. Demo mode can be disabled using  
the sDEMO MODE option in the setup menu (pg. 80).  
8
Inserting a Memory Card  
Although the camera can store pictures in internal memory, optional SD memory cards (sold sepa-  
rately) can be used to store additional pictures.  
When no memory card is inserted, a appears in the monitor and internal memory is used for recording  
and playback. Note that because camera malfunction could cause internal memory to become cor-  
rupted, the pictures in internal memory should periodically be transferred to a computer and saved on  
the computer hard disk or on removable media such as CDs or DVDs. The pictures in internal memory  
can also be copied to a memory card (see page 76). To prevent internal memory from becoming full,  
be sure to delete pictures when they are no longer needed.  
When a memory card is inserted as described below, the card will be used for recording and playback.  
Compattible MMemoorryy CCaarrddss  
FUJIFILM and SanDisk SD and SDHC memory cards have been approved for use in the camera. A com-  
plete list of approved memory cards is available at http://www.fujifilm.com/products/digital_cameras/  
index.html. Operation is not guaranteed with other cards. The camera can not be used with xD-Picture  
Cards or MultiMediaCard (MMC) devices.  
3 Caution  
SD memory cards can be locked, making it impossible to format the card or to record or  
delete images. Before inserting an SD memory card, slide the write-protect switch to the  
unlocked position.  
Write-protecctt sswwiittcch  
9
Inserting a Memory Card  
Inserting aa MMemmory Card  
Open the battery-chamber cover.  
Close the battery-chamber cover.  
1
3
1Note  
Be sure the camera is off before opening the bat-  
tery-chamber cover.  
Removing Memory Cards  
Turn the camera off and then  
press the card in and release it  
slowly. The card can now be re-  
moved by hand.  
Insert the memory card.  
2
Holding the memory card in the orientation  
shown, slide it in until it clicks into place at  
the back of the slot.  
3 Cautions  
• The memory card may spring out if you remove  
your finger immediately after pushing the card in.  
• Memory cards may be warm to the touch after be-  
ing removed from the camera. This is normal and  
does not indicate a malfunction.  
Click  
Be sure card is in correct orientation; do not  
insert at an angle or use force. If the memory  
card is not correctly inserted, pictures will be  
recorded to internal memory.  
10  
Inserting a Memory Card  
3 Cautions  
Do not turn the camera off or remove the memory card while the memory card is being formatted or data are being recorded to or  
deleted from the card. Failure to observe this precaution could damage the card.  
• Format memory cards before first use, and be sure to reformat all memory cards after using them in a computer  
or other device. For more information on formatting memory cards, see page 82.  
• Memory cards are small and can be swallowed; keep out of reach of children. If a child swallows a memory card,  
seek medical assistance immediately.  
• miniSD or microSD adapters that are larger or smaller than the standard dimensions of an SD card may not eject  
normally; if the card does not eject, take the camera to an authorized service representative. Do not forcibly  
remove the card.  
• Do not affix labels to memory cards. Peeling labels can cause camera malfunction.  
• Movie recording may be interrupted with some types of SD memory card. Use a card with a class 6 write speed  
(6MB/s) or better when shooting movies.  
• The data in internal memory may be erased or corrupted when the camera is repaired. Please note that the  
repairer will be able to view pictures in internal memory.  
• Formatting a memory card or internal memory in the camera creates a folder in which pictures are stored. Do  
not rename or delete this folder or use a computer or other device to edit, delete, or rename image files. Always  
use the camera to delete pictures from memory cards and internal memory; before editing or renaming files,  
copy them to a computer and edit or rename the copies, not the originals.  
11  
Turning the Camera on and Off  
Shooting Mode  
Playback Mode  
To turn the camera on, open the lens cover as To turn the camera on and begin playback with-  
shown below. The camera turns off when the out opening the lens cover, press the abutton  
lens cover is closed.  
for about a second.  
Camera on  
Camera off  
To turn the camera off, open and close the lens  
cover.  
2 Tip: Switching to Playback Mode  
Press the abutton for about a second to start play-  
back. Press the shutter button halfway to return to  
shooting mode.  
2 Tip: Switching to Shooting Mode  
To exit to shooting mode, press the shutter button  
halfway. Press the abutton to return to playback.  
3 Caution  
Pictures can be affected by fingerprints and other  
marks on the lenses. Keep the lenses clean.  
2 Tip: Auto Power Off  
The camera will turn off automatically if no operations are performed for the length of time selected in the  
MAUTO POWER OFF menu (pg. 84). To turn the camera on, close and reopen the lens cover or press the a  
button for about a second.  
12  
Basic Setup  
A language-selection dialog is displayed the first time the camera is turned on. Set up the camera as  
described below (for information on resetting the clock or changing languages, see page 79).  
Choose a language.  
1
1.1 Press the selector up, down, left, or right to highlight a language.  
1.2 Press MENU/OK.  
Set the date and time.  
2
2.1 Press the selector left or right to highlight the year, month, day,  
hour, or minute and press up or down to change. To change the  
order in which the year, month, and day are displayed, highlight  
the date format and press the selector up or down.  
2.2Press MENU/OK.  
13  
Basic Setup  
Choose power management options.  
3
3.1 Press the selector up or down to highlight one of the following:  
v POWER SAVE 1/w POWER SAVE 2: Save battery power. Choose  
v POWER SAVE 1 to display C images in D for increased  
savings.  
p QUICK AF: Reduce focusing time for a quick shutter response  
.
3.2 Press MENU/OK.  
2 Tip: The Camera Clock  
If the battery is removed for an extended period, the camera clock will be reset and the language-selection dialog  
will be displayed when the camera is turned on. If the battery is left in the camera for about four days, the battery  
can be removed for about a week without resetting clock, language selection, or power management options.  
14  
Taking C Pictures in Auto Mode  
This section describes how to take C pictures in B (auto) mode.  
Turn the camera on.  
Fully open the lens cover.  
Parallax (pg. 101)  
1
2
The appearance of C images  
can be adjusted using the Q  
control (pg. 2). The percent-  
age is displayed in the monitor.  
Press the shutter button to take  
a picture at the current setting,  
Rotate the mode dial to B.  
C will be displayed  
in the monitor and the  
C mode indicator will  
light.  
or press the 3D button twice to reset parallax.  
Note that adjusting parallax re-  
duces horizontal frame cover-  
age. The new crop is shown by  
black borders in the display.  
2 Tip: Auto Parallax  
For automatic parallax adjustment, select ON for  
iAUTO PARALLAX CONTROL (pg. 62). Parallax  
can still be adjusted manually when ON is selected.  
3 Caution: Excessive Parallax  
Too much parallax may make it impossible to per-  
ceive the 3D effect.  
15  
Taking C Pictures in Auto Mode  
Check the battery level.  
Check the battery level in  
the display.  
Frame the picture.  
3
4
Position the main subject in the focus frame  
and use the zoom control to frame the pic-  
ture in the display.  
Select jto zoom out  
Select ito zoom in  
Indicator  
D
Descripption  
Battery partially discharged.  
(white)  
C
Zoom indicator  
Battery more than half discharged.  
(white)  
B
Low battery. Charge as soon as pos-  
(red) sible.  
A
Battery exhausted. Turn camera off  
(blinks red) and charge battery.  
1Note: C  
The C effect may not be  
visible at high zoom ratios  
or with subjects that are outside the suggested  
range (pg. 103), poorly lit, or at the edge of the  
frame. For best results, shoot from about 1.5–  
2m/4.9–6.6 ft. (wide angle).  
Approx. 1.5–2 m  
(4.9–6.6 ft.)  
16  
Taking C Pictures in Auto Mode  
Holding the Camera  
Shooting Information  
To choose the shooting information and guides dis-  
played, press the DISP/BACK button.  
Hold the camera steady with both hands and brace  
your elbows against your sides. Shaking or unsteady  
hands can blur your shots.  
Indicators displayed  
Indicators hidden  
Best framing  
Hiding indicators makes it easier to see the C effect.  
To use best framing, position the main subject at the  
intersection of two lines or align one of the horizontal  
lines with the horizon. Use focus lock (pg. 32) to focus  
on subjects that will not be in the center of the frame  
in the final photograph.  
To avoid interfering with the C effect and to pre-  
vent pictures that are out of focus or too dark (under-  
exposed), keep your fingers and other objects well  
away from the lenses and flash. Note that the C  
effect may not be visible if the display is viewed at  
an angle.  
2 Tip: Focus Lock  
Use focus lock (pg. 32) to focus on subjects that are not  
in the focus frame.  
17  
Taking C Pictures in Auto Mode  
Focus.  
Silent Mode  
5
Press the shutter button halfway to focus on  
the main subject in the focus frame.  
In situations in which camera sounds or lights may be  
unwelcome, hold the DISP/BACK button down until o  
is displayed (silent mode can also be selected using  
the oSILENT MODE option in the setup menu as  
described on page 79).  
Press  
halfway  
Focus frame  
1Note  
Camera selects small focus  
frame and focuses on subject  
The lenses may make a noise when the camera  
focuses. This is normal.  
The speaker, flash, illuminator, and self-timer lamp  
turn off and flash and volume settings can not be  
adjusted (note that the flash will still fire when C  
is selected in scene mode). To restore normal opera-  
tion, press the DISP/BACK button until the o icon is no  
longer displayed.  
If the camera is able to focus with both lenses, it  
will beep twice and the indicator lamp will  
glow green.  
If the camera is unable to focus, the focus frame  
will turn red, s will be displayed, and the  
indicator lamp will blink green. Change the  
composition or use focus lock (pg. 32).  
18  
Taking C Pictures in Auto Mode  
Shoot.  
The Indicator Lamp  
6
Smoothly press the shutter button  
the rest of the way down to take  
the picture.  
Indicator lamp  
2 Tip: The Shutter Button  
The shutter button has two positions. Pressing the  
The indicator lamp shows camera status as follows:  
shutter button halfway ( ) sets focus and exposure;  
q
Indicatoor lamp  
Camera status  
to shoot, press the shutter button the rest of the way  
down ( ).  
w
Glows green Focus locked.  
Blur, focus, or exposure warning. Pic-  
ture can be taken.  
Blinks green  
Double  
beep  
Click  
Blinks green and Recording pictures. Additional pictures  
orange  
can be taken.  
q
w
Recording pictures. No additional pic-  
tures can be taken at this time.  
Flash charging; flash will not fire when  
picture is taken.  
Lens or memory error (internal memory  
or memory card full or not formatted,  
format error, or other memory error).  
Glows orange  
Blinks orange  
Blinks red  
Press halfway  
Press the rest of  
the way down  
1Note  
If the subject is poorly lit, the flash may fire when the  
picture is taken. For information on using the flash  
when lighting is poor, see page 35.  
2 Tip: Warnings  
Detailed warnings appear in the display. See pages  
96–99 for more information.  
19  
Viewing C Pictures  
Pictures can be viewed in the monitor. When taking important photographs, take a test shot and  
check the results. C pictures are stored in multi-picture (“.mpo”) format; JPEG copies can be recorded  
by selecting MPO+JPEG for the o3DREC option in the setup menu.  
Press the abutton.  
Deleting Pictures  
1
2
The most recent picture  
will be displayed in the  
monitor. Pictures taken in  
C are indicated by a g  
icon; confirm that C ap-  
pears in the display.  
To delete the picture currently displayed  
in the monitor, press the selector up (b).  
The following dialog will be displayed.  
View additional pictures.  
Press the selector right to  
view pictures in the order  
recorded, left to view pictures in reverse or-  
der.  
To delete the picture, highlight OK and  
press MENU/OK. To exit without deleting  
the picture, highlight CANCEL and press  
MENU/OK.  
Press the shutter button to exit to shooting  
mode.  
2 Tip: The Playback Menu  
Pictures can also be deleted from the playback menu  
(pg. 42).  
20  
Shooting and Viewing D Pictures  
Taking Pictures in D  
Viewing Pictures in D  
To shoot pictures in D, press the 3D button to D pictures can be viewed as described on page  
select D mode.  
20. Note that when C pictures are viewed in  
D, only the image recorded with the left lens  
will be displayed.  
Take pictures as described on pages 15–19. D  
is displayed in the monitor and photographs are  
taken using the left lens and saved in JPEG (“.jpg”)  
format (Exif 2.3).  
Images that were originally recorded in D are  
indicated by the absence of a g icon.  
Note that the picture angle of photographs taken  
in D differs from that of C images.  
21  
Shooting Mode  
Choose a shooting mode according to the scene or type of subject. To choose a shooting mode, rotate  
the mode dial to the desired setting (pg. 4). The following modes are available:  
Press the selector up or down to  
highlight a scene (pg. 23).  
B AUTO  
2
Choose for crisp, clear snapshots (pg. 15). This  
mode is recommended in most situations.  
Press MENU/OK to select the high-  
lighted option.  
3
SP1/SP2 SCENE POSITION  
The camera offers a choice of “scenes,” each  
adapted to particular shooting conditions or a  
specific type of subject, which can be assigned  
to the SP1 and SP2 positions on the mode dial.  
Each position can be assigned a different scene:  
Press DISP/BACK to return to shooting  
mode.  
4
Select SP1 or SP2 and press MENU/OK  
to display the following menu.  
1
Note: If the shooting menu is  
displayed, highlight ASCENE  
POSITION and press MENU/OK.  
22  
Shooting Mode  
Scene  
Descripption  
Choose EANTI-BLUR (picture stabilization) mode for fast shutter speeds that reduce blur caused by  
camera shake or subject movement. Recommended for photographs of children and pets.  
E ANTI-BLUR  
Get good results with backlit subjects and other difficult lighting. The camera takes two shots: one without  
the flash and one with.  
CNATURAL & N  
Capture natural light indoors, under low light, or where the flash can not be used. The flash turns off and  
sensitivity is raised to reduce blur.  
D NATURAL LIGHT  
L
PORTRAIT  
Choose for soft-toned portraits with natural skin tones.  
M
LANDSCAPE  
Choose for crisp, clear daylight shots of buildings and landscapes.  
Choose when photographing moving subjects. p QUICK AF is automatically selected for SPOWER  
MANAGEMENT and priority is given to faster shutter speeds.  
Choose this mode for poorly lit twilight or night scenes. Sensitivity is automatically raised to reduce blur  
caused by camera shake.  
N
O
SPORT  
NIGHT  
H NIGHT (TRIPOD) Choose this mode for slow shutter speeds when shooting at night. Use a tripod to prevent blur.  
Q
R
S
F
U
SUNSET  
SNOW  
BEACH  
Record the vivid colors in sunrises and sunsets.  
Choose for crisp, clear shots that capture the brightness of scenes dominated by shining white snow.  
Choose for crisp, clear shots that capture the brightness of sunlit beaches.  
UNDERWATER Choose for vivid blues when taking photographs of subjects in an aquarium.  
PARTY Capture indoor background lighting under low-light conditions.  
23  
Shooting Mode  
M MANUAL  
In this mode, you choose both shutter speed and aperture. If desired, exposure can be altered from  
the value suggested by the camera.  
Select mode M and press MENU/OK to  
display the shooting menu.  
Press the selector up or down to  
choose the aperture, left or right to  
choose the shutter speed.  
1
4
Press MENU/OK.  
5
6
Press the selector up or down to  
highlight dSET SHUTTERSPEED,  
APERTURE..  
Press DISP/BACK to return to shooting  
mode.  
2
3
Take pictures.  
7
Press MENU/OK. Shutter speed and  
aperture will be displayed.  
The Exposure Indicator  
The amount the picture will be  
under- or over-exposed at cur-  
rent settings is shown by the ex-  
posure indicator.  
Shutter speed  
Aperture  
24  
Shooting Mode  
A APERTURE PRIORITY AE  
In this mode, you choose the aperture while the camera adjusts shutter speed for optimal exposure.  
Select mode A and press MENU/OK to  
display the shooting menu.  
Press the selector up or down to  
choose exposure compensation, left  
or right to choose the aperture.  
1
4
Press MENU/OK.  
5
6
Press the selector up or down to  
highlight dSETTING APERTURE.  
Press DISP/BACK to return to shooting  
mode.  
2
3
Take pictures. If the correct exposure can not  
be achieved at the selected aperture, shutter  
speed will be displayed in red when the shut-  
ter button is pressed halfway. Adjust aperture  
until the correct exposure is achieved.  
Press MENU/OK. Exposure compensa-  
tion and aperture will be displayed.  
7
Exposure compensation  
3 Caution  
If the subject is outside the metering range of the cam-  
era, the shutter speed display will show “---”. Press the  
shutter button halfway to measure exposure again.  
Aperture  
25  
Shooting Mode  
P PROGRAM AE  
In this mode, the camera sets aperture and shutter speed automatically. Exposure can be adjusted  
using the dEXP. COMPENSATION option in the shooting menu.  
3 Caution  
If the subject is outside the metering range of the camera, the shutter speed and aperture displays will show “---”.  
Press the shutter button halfway to measure exposure again.  
26  
Shooting Mode  
I ADVANCED 2D  
The camera simultaneously takes two D pictures—one with each lens—with different options se-  
lected for each.  
Select I and press MENU/OK to  
display I options.  
Press MENU/OK to select the high-  
lighted option.  
1
2
3
4
Press DISP/BACK to return to shooting  
mode.  
Press the selector up or down to  
highlight one of the following op-  
tions:  
V TELE/WIDE: Zoom for the left lens can be  
adjusted using the zoom control. The right  
lens is zoomed all the way out (pg. 28).  
X 2-COLOR: The two pictures use different  
settings for FINEPIX color (pg. 28).  
W 2-SENSITIVITY: The camera sets sensitivity  
separately for each lens (pg. 28).  
3 Caution: I Mode  
In mode, the camera displays the view through the left lens only. Be careful not to ob-  
struct the right lens during shooting.  
I
27  
Shooting Mode  
V TELE//WIDE  
W 2-SENSIITIIVITY  
Zoom for the left lens can be  
adjusted using the zoom con-  
trol. The right lens is zoomed  
all the way out.  
If lighting permits, sensitivity is set higher for the  
right lens than for the left (the maximum value for  
the left lens is ISO 400, that for the right lens ISO  
1600; note that the same value may be used for  
both lenses if the subject is brightly lit).  
Sensiitivity  
X 2-COLOR  
Lightinng  
Dark  
Left lens  
ISO 400  
Right leens  
ISO 1600  
Select the desired combination of color options  
using the j2-COLOR SETTING option in the  
shooting menu (pg. 61).  
ISO 100  
ISO 100  
ISO 400  
ISO 100  
Bright  
The selected combination is  
shown by an icon in the display.  
Higher sensitivities permit faster shutter speeds.  
If you pan the camera to follow a moving object,  
the background in the shot taken with the right  
lens will be less blurred than in the shot taken  
with the left, producing different speed effects. If  
lighting is poor, the shot taken with the right lens  
will be less blurred, while the shot taken with the  
left lens will have less noise.  
28  
Shooting Mode  
H ADVANCED 3D  
This mode offers greater C flexibility than B mode. The camera takes two shots with the left lens  
and combines them to form a C picture.  
Select H and press MENU/OK to  
display H options.  
Press MENU/OK to select the high-  
lighted option.  
1
2
3
4
Press DISP/BACK to return to shooting  
mode.  
Press the selector up or down to  
highlight one of the following op-  
tions:  
B INTERVAL 3D SHOOTING: The camera auto-  
matically takes the two shots at a fixed inter-  
val (pg. 31).  
A INDIVID. SHUTTER 3D: One shot is taken each  
time you press the shutter button (pg. 30).  
29  
Shooting Mode  
A INDIVIIDD.. SSHHUUTTTTEERR 33DD  
Use this option to combine two shots taken from  
different angles to create a C picture. Use in  
macro mode, to create C pictures of distant ob-  
ject, and in other situations in which the desired  
results can not be achieved in B (auto) mode.  
Take the first shot.  
2
3
1Note  
To exit without taking the second shot, press DISP/  
BACK or turn the camera off. Note that the camera  
will turn off and shooting will be cancelled if no  
operations are performed for the length of time se-  
lected for MAUTO POWER OFF (pg. 84).  
The first shot will be superimposed on the  
view through the lens. Using the first shot as  
a guide, reposition the camera and take the  
second shot to create a C picture. Note that  
the 3D effect may not be visible if the paral-  
lax between the two positions is too great; the  
best results will be achieved if the distance the  
camera is moved between the two shots is  
Choose the order in which the shots will be  
taken (left first or right first) using the lTURN  
option in the shooting menu (pg. 61).  
1
th  
th  
1
1
/
/
between 30 and 50 of the distance to the  
subject.  
First shot shown by E  
30  
Shooting Mode  
B INTERVAAL 3D SHOOTTING  
Use this option to take C pictures of distant ob-  
jects from a moving vehicle.  
Choose the order in which the shots will be  
taken (left first or right first) using the lTURN  
option in the shooting menu (pg. 61). Choose  
the order that matches the direction of mo-  
tion.  
2
3
Select the delay between the two shots us-  
1
ing the k3D INTERVAL TIME option in the  
shooting menu (pg. 61). Choose shorter delays  
for less distant objects or faster-moving ve-  
hicles (the best results will be achieved if the  
First shot shown by E  
Take the first shot. A timer  
distance the camera moves between the two  
th  
shots is between 1 30 and 1 50th of the distance  
to the subject). The 3D effect may not be vis-  
ible if the parallax between the two shots is  
too great or if another object is between the  
camera and your subject.  
is displayed after the first  
shot; the second shot is tak-  
en when the timer reaches  
zero. No operations can  
be performed while the timer is active; if the  
camera is turned off before the second shot is  
taken, no picture will be recorded.  
/
/
31  
Focus Lock  
To compose photographs with off-center subjects:  
Position the subject in the focus frame.  
Recompose the picture.  
Keeping the shutter button pressed halfway,  
recompose the picture.  
1
3
4
Focus.  
2
Press the shutter button halfway to set fo-  
cus and exposure. Focus and exposure (and  
in C mode, parallax; pg. 15) will remain  
locked while the shutter button is pressed  
halfway (AF/AE lock).  
Shoot.  
Press the shutter-release button the rest of  
the way down to take the picture.  
Press the rest of  
the way down  
Press  
halfway  
Repeat steps 1 and 2 as desired to refocus  
before taking the picture.  
32  
Focus Lock  
Autofocus  
Although the camera boasts a high-precision autofocus system, it may be unable to focus on the subjects listed  
below. If the camera is unable to focus using autofocus, use focus lock (pg. 32) to focus on another subject at  
the same distance and then recompose the photograph.  
• Very shiny subjects such as mir-  
rors or car bodies.  
• Fast-moving subjects.  
• Subjects photographed through a window or other reflective object.  
• Dark subjects and subjects that absorb rather than reflect light, such as hair or fur.  
• Insubstantial subjects, such as smoke or flame.  
• Subjects that show little contrast with the background (for example, subjects in clothing that is the same color  
as the background).  
• Subjects positioned in front of or behind a high-contrast object that is also in the focus frame (for example, a  
subject photographed against a backdrop of highly contrasting elements).  
Auto Parallax  
Although the camera boasts highly precise parallax control, auto parallax may not produce the desired results  
with the subjects listed under “Autofocus” (above) or with subjects outside the recommended range (particu-  
larly if the subject is close to the camera), repeating rectangular patterns such as venetian blinds or the windows  
in an office building, or straight lines such as poles or wires. Use focus lock (pg. 32) or adjust parallax manually  
(pg. 15).  
33  
F Macro Mode (Close-ups)  
For close-ups, press the selector left (F) to display macro close-up options. Press the selector left or  
right to highlight F and press MENU/OK.  
Choose from F (macro mode)  
or OFF (macro mode off)  
When macro mode is in effect, the camera focuses on subjects near the center of the frame. Use the  
zoom control to compose pictures (pg. 16).  
To exit macro mode, press the selector left (F) and select OFF.  
1Notes  
• Use of a tripod is recommended to prevent blur caused by camera shake.  
• The flash may fail to light the entire subject at very short ranges. Increase the distance to the subject and try  
again.  
3 Caution  
C pictures taken in macro mode may not produce the desired results when viewed on TV.  
34  
N Using the Flash (Super Intelligent Flash)  
When the flash is used, the camera’s Super Intelligent Flash system instantly analyzes the scene based  
on such factors as the brightness of the subject, its position in the frame, and its distance from the  
camera. Flash output and sensitivity are adjusted to ensure that the main subject is correctly exposed  
while preserving the effects of ambient background lighting, even in dimly-lit indoor scenes. Use the  
flash when lighting is poor, for example when shooting at night or indoors under low light.  
Choose a flash mode.  
1
Press the selector right (N). The following options will be displayed;  
press the selector left or right to highlight an option and press MENU/OK.  
In modes other than A, the current mode is indicated by an icon in  
the display.  
Mode  
Descripption  
A (AUTO FLASH)  
The flash fires when required. Recommended in most situations.  
As above, except that camera minimizes “red-eye” caused when light from the flash is re-  
flected from the subject’s retinas.  
K (RED EYE REDUCTION)  
The flash fires whenever a picture is taken. Use for backlit subjects or for natural coloration  
when shooting in bright light.  
N
(FORCED FLASH)  
L(FORCED FLASH)  
As for fill flash, except that camera minimizes “red-eye.”  
The flash does not fire even when the subject is poorly lit. k will appear in the monitor  
P (SUPPRESSED FLASH) at slow shutter speeds to warn that pictures may be blurred. Use of a tripod is recom-  
mended.  
Capture both the main subject and the background under low light (note that brightly lit  
scenes may be overexposed).  
O (SLOW SYNCHRO)  
M (RED EYE & SLOW)  
As for slow sync, except that camera minimizes “red-eye.”  
35  
N Using the Flash (Super Intelligent Flash)  
Focus.  
2
3
Press the shutter button halfway to focus. If the flash will fire, p will be displayed when  
the shutter button is pressed halfway. At slow shutter speeds, k will appear in the dis-  
play to warn that pictures may be blurred; choose another flash mode or use a tripod.  
Shoot.  
Press the shutter button the rest of the way down to shoot.  
3 Caution  
The flash may fire several times with each shot. Do not move the camera until shooting is com-  
plete.  
Red-Eye Reduction  
Red-eye reduction minimizes “red-eye” caused when light from the flash is reflected from the sub-  
ject’s retinas as shown in the illustration at right.  
2 Tip: Red-Eye Removal (D Only)  
When ON is selected for both bFACE DETECTION in the shooting menu (D only; pg. 67) and BRED EYE  
REMOVAL in the setup menu (pg. 79), pictures are processed to remove red-eye and the flash mode can be  
selected from K, L, and M. Unprocessed copies of pictures taken using red-eye removal can be saved using  
nSAVE ORG IMAGE in the setup menu (pg. 80).  
36  
hUsing the Self-Timer  
The camera offers a ten-second timer that allows photographers to appear in their own photographs,  
and a two-second timer that can be used to avoid blur caused by the camera moving when the shutter  
button is pressed. The self-timer is available in all shooting modes.  
Set the timer.  
1
The current self-timer mode is displayed in the monitor. To choose a different setting, press the  
selector down (h). Self-timer options will be displayed; press the selector left or right to highlight  
an option and press MENU/OK.  
Choose from T (self-timer off),  
S (10 s delay), or R (2 s delay)  
Focus.  
2
Press the shutter button halfway to focus.  
3 Caution  
Stand behind the camera when using the shutter button. Standing in front  
of the lens can interfere with focus and exposure.  
Start the timer.  
3
Press the shutter button the rest of the way down to start the timer.  
The display in the monitor shows the number of seconds remaining  
until the shutter is released. To stop the timer before the picture is  
taken, press DISP/BACK.  
37  
hUsing the Self-Timer  
The self-timer lamp on the front of the camera will blink  
immediately before the picture is taken. If the two-sec-  
ond timer is selected, the self-timer lamp will blink as the  
timer counts down.  
Intelligent Face Detection (D)  
Because it ensures that the faces of portrait subjects will be in focus, Intelligent Face Detection (pg. 67) is recom-  
mended when using the self-timer for group portraits or self-portraits. To use the self-timer with Intelligent Face  
Detection, turn Intelligent Face Detection on, set the timer as described in Step 1, and then press the shutter  
button all the way down to start the timer. The camera will detect faces while the timer is counting down and  
adjust focus and exposure immediately before the shutter is released. Be careful not to move until the picture  
has been recorded.  
1Note  
The self-timer turns off automatically when the picture is taken, a different shooting mode is selected, playback  
mode is selected, or the camera is turned off.  
38  
Playback Options  
To view the most recent picture in the monitor,  
press the abutton.  
Choosing a Display Format  
Press the DISP/BACK button to cycle through playback  
display formats as shown below.  
Press the selector right to view pictures  
in the order recorded, left to view pic-  
tures in reverse order. Keep the selector  
pressed to scroll rapidly to the desired  
frame.  
Indicators  
displayed  
Indicators  
hidden  
C
D
Switching Between  
and  
Press the 3D button to switch be-  
tween C and D display (note  
that D pictures are always dis-  
played in D). In C playback,  
use the Q control to adjust  
parallax.  
12/31  
Sort by date  
Hide indicators for improved C viewing.  
1Note  
Pictures taken using other cameras are indicated by a m (“gift image”) icon during playback.  
39  
Playback Options  
Playback Zoom  
Select i to zoom in on pictures displayed in  
single-frame playback; select j to zoom out.  
When the picture is zoomed in, the selector can  
be used to view areas of the image not currently  
visible in the display.  
Intelligent Face Detection (D Only)  
Pictures taken with Intelligent  
Face Detection (pg. 67) are in-  
dicated by a g icon. Press the  
selector down to zoom in on the  
subject selected with Intelligent  
Face Detection. You can then  
Zoom indicator  
Navigation window shows  
portion of image currently  
displayed in monitor  
use the zoom control to zoom in and out.  
Press DISP/BACK to exit zoom.  
1Note  
Playback zoom is not available with cropped copies  
saved at a size of a or copies created with ORESIZE  
(pg. 74).  
3 Caution: C Playback  
C pictures are best viewed with the camera held  
horizontally. The 3D effect may not be visible at high  
zoom ratios or when the monitor is viewed at an angle.  
If C pictures appear blurred even after parallax is ad-  
justed, select D playback.  
40  
Playback Options  
Multi-Frame Playback  
To change the number of images dis-  
played, select j when a picture is  
shown full-frame in the monitor.  
Sort by Date  
Choose sort-by-date mode to view pictures taken  
on a selected date.  
Press DISP/BACK until the sort-by-date  
screen is displayed.  
1
Select j to increase the number of  
pictures displayed to five, nine, or a  
hundred.  
3D  
12/31  
Select ito reduce the number of im-  
ages displayed.  
Use the selector up or down to  
2
highlight a date. Keep the selector  
pressed to scroll rapidly to the de-  
sired date.  
Use the selector to highlight images and press  
MENU/OK to view the highlighted image full frame.  
In the nine- and hundred-frame displays, press  
the selector up or down to view more pictures.  
Press the selector left or right to  
3
scroll through the pictures taken on  
the highlighted date. Keep the se-  
lector pressed to scroll rapidly to the  
desired frame.  
41  
ADeleting Pictures  
The AERASE option in the playback menu can be used to delete still pictures and movies, increasing  
the amount of space available on the memory card or in internal memory (for information on deleting  
pictures in single-frame playback, see page 20). Note that deleted pictures can not be recovered. Copy  
important pictures to a computer or other storage device before proceeding.  
2 Tips: Deleting Pictures  
Press MENU/OK to display the play-  
back menu.  
1
2
• When a memory card is inserted, pictures will be de-  
leted from the memory card; otherwise, pictures will  
be deleted from internal memory.  
• Protected pictures can not be deleted. Remove pro-  
tection from any pictures you wish to delete (pg. 72).  
• If a message appears stating that the selected images  
are part of a DPOF print order, press MENU/OK to delete  
the pictures.  
Press the selector up or down to  
highlight AERASE.  
Press the selector right to display de-  
lete options.  
3
4
Press the selector up or down to  
highlight FRAME or ALL FRAMES.  
Press MENU/OK to display options for  
the selected item (pg. 43).  
5
42  
ADeleting Pictures  
FRAME: Deletingg Sellected IImages  
Selecting FRAME displays the  
dialog shown at right.  
ALLLL FFRRAAMMEESS:: DDeelleetting Alll Images  
Selecting ALL FRAMES dis-  
plays the confirmation shown  
at right.  
Press the selector left or right  
to scroll through pictures and  
press MENU/OK to delete the  
current picture (the picture is  
deleted immediately; be care-  
ful not delete the wrong picture).  
Highlight OK and press MENU/  
OK to delete all unprotected  
pictures.  
The dialog shown at right is dis-  
played during deletion. Press  
DISP/BACK to cancel before all  
Press DISP/BACK to exit when all the desired pic- pictures have been deleted  
tures have been deleted. (any pictures deleted before  
the button was pressed can not be recovered).  
43  
FRecording Movies  
Shoot short movies. C movies are recorded in 3D movie format (pg. 100), D movies in motion  
JPEG format with stereo sound recorded via the built-in microphone (be careful not to cover the mi-  
crophone during recording).  
Press the Fbutton.  
Choosing the Frame Size  
1
To choose the frame size when  
recording movies to a memory  
card, press MENU/OK and select  
Display shows time  
available  
OQUALITY.  
Choose  
j
(1280×720 pixels) for an aspect  
ratio of 16:9 (High Definition), f  
(640×480 pixels) for high-quality standard definition  
movies, or g (320×240 pixels) for longer movies (if  
no memory card is inserted, movies will be recorded  
at a frame size of g). Press MENU/OK to return to movie  
recording mode.  
Use the 3D button to choose  
between C and D re-  
cording. The current mode  
is shown in the monitor.  
2
1Note: Auto Parallax  
If ON is selected for iAUTO PARALLAX CON-  
TROL (pg. 62), parallax will be adjusted automati-  
cally when the shutter button is pressed halfway.  
If OFF is selected, adjust parallax manually before  
recording begins (pg. 15).  
44  
FRecording Movies  
Frame the scene using the zoom control.  
Press the shutter button halfway to end record-  
ing. Recording ends automatically when the  
movie reaches maximum length or memory is  
full.  
3
4
5
Zoom indicator  
3 Caution  
Zoom can not be adjusted once recording  
begins.  
The indicator lamp lights while movies are being re-  
corded. Do not open the battery chamber cover dur-  
ing shooting or while the indicator lamp is lit. Failure to  
observe this precaution could prevent the movie from  
being played back.  
Press the shutter button all the way down to  
start recording.  
zREC and time  
remaining are  
displayed  
2 Tip  
There is no need to keep the shutter button pressed  
during recording.  
1Note  
Focus is set when recording begins; exposure and  
white balance are adjusted automatically through-  
out recording. The color and brightness of the im-  
age may vary from that displayed before recording  
begins.  
45  
aViewing Movies  
During playback, movies are  
displayed in the monitor as  
shown at right. The following  
operations can be performed  
while a movie is displayed:  
Progress is shown in the monitor during play-  
back.  
Progress bar  
Operration  
Descripption  
Start/pause Press the selector down to start playback.  
playback Press again to pause.  
2 Tip: Viewing Movies on a Computer  
Copy movies to the computer before viewing.  
End  
Press the selector up to end playback. If  
playback/ playback is not in progress, pressing the  
delete selector up will delete the current movie.  
Press the selector right to advance, left to  
Advance/ rewind. If playback is paused, the movie  
rewind will advance or rewind one frame each  
time the selector is pressed.  
3 Cautions  
• Do not cover the speaker during playback.  
• Vertical or horizontal streaks may appear in movies  
containing very bright subjects. This is normal and  
does not indicate a malfunction.  
• HD movies recorded with this camera can not be  
viewed on FINEPIX HDP-L1 HD players or FINEPIX  
REAL 3D V1 photo frames.  
• Movies recorded with this camera can not be viewed  
on FINEPIX REAL 3D W1 cameras. This camera can  
display movies recorded with the FINEPIX REAL 3D  
W1, but can not be used to display such movies on  
HDMI devices.  
Press MENU/OK to pause playback and dis-  
Adjust play volume controls. Press the selector  
volume up or down to adjust the volume; press  
MENU/OK again to resume playback.  
46  
Viewing Pictures on TV  
Connect the camera to a TV and tune the television to the video channel to show pictures to a group.  
The optional A/V cable connects as shown below. Turn the camera off before connecting the cable.  
Connect yellow plug  
to video-in jack  
Insert into A/V cable  
connector  
Connect white plug  
to audio-in jack  
Press a for about a second to turn the camera on. The camera monitor turns off and pictures are  
played back on the TV, with C images displayed in D. Note that the camera volume controls have  
no effect on sounds played on the TV; use the television volume controls to adjust the volume.  
1Note  
Image quality drops during movie playback.  
3 Caution  
When connecting the cable, be sure the connectors are fully inserted.  
47  
Viewing Pictures on a 3D TV  
A high-speed HDMI cable (available from third-party suppliers; pg. 86) can be used to connect the  
camera to High Definition (HD) devices (playback only).  
Insert into HDMI  
connector  
Insert into HDMI  
connector  
HDMI Mini Connector  
1Note  
While an HDMI cable is connected, the television will be used for playback only and the USB cable can not be con-  
nected. The display format for HDMI output can be selected from 3D, 2D, and SIDE-BY-SIDE using the wHDMI  
OUTPUT option in the setup menu (pg. 83). Note that if the television supports 3D display, playback zoom,  
parallax adjustment, and the ORESIZE and GCROP options in the playback menu will not be available and  
the following types of C picture will be displayed in D: pictures taken using H, 3D still images and movies  
created using MyFinePix Studio, cropped or resized images, and still images and movies for which parallax has  
been adjusted using the iPARALLAX CONTROL option in the playback menu (pg. 70).  
48  
Printing Pictures via USB (D Only)  
If the printer supports PictBridge, the camera can be connected directly to the printer and  
pictures can be printed without first being copied to a computer. Note that depending on the  
printer, not all the functions described below may be supported.  
Printing in C  
C pictures in MPO format can not be printed via direct USB connection, although JPEG copies created when  
MPO+JPEG is selected for o3DREC can be printed in D (pg. 85). For information on C prints, visit http://  
fujifilm.com/3d/print/.  
Connecting the Camera  
Connect the supplied USB cable as shown and  
turn the printer on.  
Press the abutton for about a second to turn  
the camera on. t USB will be displayed in  
the monitor, followed by the PictBridge display  
shown below at right.  
1
2
1Notes  
• Print pictures from internal memory or a memory card that has been formatted in the camera.  
• Default printer page size and print quality settings are used when printing via direct USB connection.  
49  
Printing Pictures via USB (D Only)  
Printing Selected Pictures  
Press the selector left or right to dis-  
play a picture you wish to print.  
Press MENU/OK to display a confirma-  
tion dialog.  
1
3
4
1Note  
To print one copy of the current picture, proceed  
directly to Step 3.  
Press the selector up or down to  
2
choose the number of copies (up to  
99). Repeat steps 1–2 to select addi-  
tional pictures.  
Press MENU/OK to start printing.  
50  
Printing Pictures via USB (D Only)  
2 Tip: Printing the Date of Recording  
During Printing  
To print the date of recording on pictures, press DISP/  
BACK in steps 1–2 to display the PictBridge menu (see  
“Printing the DPOF Print Order,” below). Press the se-  
lector up or down to highlight PRINT WITH DATE s  
and press MENU/OK to return to the PictBridge display  
(to print pictures without the date of recording, select  
PRINT WITHOUT DATE). To ensure that the date is cor-  
rect, set the camera clock before taking pictures. Note  
that the PRINT WITH DATE s option is only available  
with printers that support date printing.  
The message shown at right is  
displayed during printing. Press  
DISP/BACK to cancel before all  
pictures are printed (depending  
on the printer, printing may end  
before the current picture has printed).  
If printing is interrupted, press ato turn the camera  
off and then on again.  
Disconnecting the Camera  
Confirm that the above message is not displayed and  
turn the camera off. Disconnect the USB cable.  
51  
Printing Pictures via USB (D Only)  
Printing the DPOF Print Order  
To print the print order created with KPRINT ORDER (DPOF) in the playback menu (pg. 69):  
In the PictBridge display, press DISP/  
BACK to open the PictBridge menu.  
Press MENU/OK to display a confirma-  
tion dialog.  
1
2
3
Press the selector up or down to  
highlight u PRINT DPOF.  
Press MENU/OK to start printing.  
4
52  
Printing Pictures via USB (D Only)  
Creating a DPOF Print Order  
The KPRINT ORDER (DPOF) option in the play- Press MENU/OK and follow the steps below.  
back menu can be used to create a digital “print  
Press the selector left or right to dis-  
1
order” for PictBridge-compatible printers (pg. 49)  
play a picture you wish to include in  
or devices that support DPOF.  
or remove from the print order.  
DPOF  
Press the selector up or down to  
2
DPOF (Digital Print Order Format) is standard  
choose the number of copies (up  
that allows pictures to be printed from “print  
to 99). To remove a picture from the  
orders” stored in internal memory or on a  
memory card. The information in the order includes  
the pictures to be printed and the number of copies  
of each picture.  
order, press the selector down until  
the number of copies is 0.  
Total number of prints  
Number of copies  
WITH DAATE s/ WWITHOUT DATE  
To modify the DPOF print order, select KPRINT  
ORDER (DPOF) in the playback menu and press  
the selector up or down to highlight WITH  
DATE s or WITHOUT DATE.  
2 Tip: Intelligent Face Detection  
If the current picture was created with Intelligent  
Face Detection (pg. 67), pressing the selector down  
sets the number of copies to the number of faces  
detected.  
WITH DATE s: Print date of record-  
ing on pictures.  
WITHOUT DATE: Print pictures without  
date.  
53  
Printing Pictures via USB (D Only)  
Repeat steps 1–2 to complete the  
print order. Press MENU/OK to save  
the print order when settings are complete,  
or DISP/BACK to exit without changing the print  
order.  
RESET AALL  
3
4
To cancel the current print or-  
der, select RESET ALL in the  
KPRINT ORDER (DPOF)  
menu. Theconfirmationshown  
at right will be displayed; press  
The total number of prints is dis-  
played in the monitor. Press MENU/OK  
to exit.  
MENU/OK to remove all pictures from the order.  
1Notes  
• Remove the memory card to create or modify a print  
order for the pictures in internal memory.  
• Print orders can contain a maximum of 999 pictures.  
The pictures in the current  
print order are indicated by a  
u icon during playback.  
• If a memory card is inserted con-  
taining a print order created by  
another camera, the message  
shown at right will be displayed.  
Pressing MENU/OK cancels the  
print order; a new print order  
must be created as described above.  
54  
Viewing Pictures on a Computer  
The supplied software can be used to copy pictures to a computer, where they can be stored, viewed,  
organized, and printed. Before proceeding, install the software as described below. Do NOT connect the  
camera to the computer until installation is complete.  
Installing the Software  
Confirm that the computer meets the following system requirements:  
1
Windows 7*  
Windowss Vista*  
Windoows XP*  
2GHz Pentium 4 or better†  
512MB or more‡  
CPU  
RAM  
3GHz Pentium 4 or better†  
1GB or more  
15GB or more  
Free disk space  
2GB or more  
• 1024×768 pixels or more with 24-bit color or better  
• A graphics processing unit (GPU) that supports DirectX 7 or later  
Video  
• Built-in USB port recommended. Operation is not guaranteed with other USB ports.  
Other  
• Internet connection (broadband recommended) required to install .NET Framework (if necessary), to use  
auto update feature, and when performing such tasks as sharing pictures online or via e-mail.  
* Other versions of Windows are not supported. Only pre-installed operating systems are supported; operation is not  
guaranteed on home-built computers or computers that have been upgraded from earlier versions of Windows.  
† 2.4GHz Core Duo 2 or better recommended when viewing C HD movies.  
1GB or more recommended when viewing C HD movies.  
Start the computer. Log in to an account with administrator privileges before proceeding.  
2
55  
Viewing Pictures on a Computer  
Exit any applications that may be running and insert the installer CD in a CD-ROM drive.  
3
Windows 7/Windows Vista  
If an AutoPlay dialog is displayed, click SETUP.EXE. A “User Account Control” dialog will then be displayed;  
click Yes (Windows 7) or Allow (Windows Vista).  
The installer will start automatically; click Install MyFinePix Studio and follow the on-screen in-  
structions to install MyFinePix Studio.  
If the Installer Does Not Start Automatically  
If the installer does not start automatically, select Computer or My Computer from the Start menu, then  
double-click the FINEPIX CD icon to open the FINEPIX CD window and double-click setup or SETUP.EXE.  
If prompted to install Windows Media Player, DirectX, or .NET Framework, follow the on-screen in-  
structions to complete installation.  
4
5
Remove the installer CD from the CD-ROM drive when installation is complete. Store the installer  
CD in a dry location out of direct sunlight in case you need to re-install the software. The version  
number is printed at the top of the CD label for reference when updating the software or contacting  
customer support.  
Installation is now complete. Proceed to “Connecting the Camera” on page 57.  
56  
Viewing Pictures on a Computer  
Connecting the Camera  
If the pictures you wish to copy are stored on a  
Press the abutton for about a second to turn  
the camera on. MyFinePix Studio will start au-  
tomatically; follow the on-screen instructions  
to copy pictures to the computer. To exit with-  
out copying pictures, click Cancel.  
1
3
memory card, insert the card into the camera  
(pg. 10). If no card is inserted, pictures will be  
copied from internal memory.  
1Note  
The Windows CD may be required when the soft-  
ware is started for the first time.  
3 Caution  
If the software does not start automatically, it may  
not be correctly installed. Disconnect the camera  
and reinstall the software.  
3 Caution  
Loss of power during transfer could result in loss of  
data or damage to internal memory or the memory  
card. Charge the battery before connecting the  
camera.  
For more information on using the supplied soft-  
ware, start the application and select the appro-  
priate option from the Help menu.  
Turn the camera off and connect the supplied  
2
USB cable as shown, making sure the connec-  
tors are fully inserted. Connect the camera di-  
rectly to the computer; do not use a USB hub  
or keyboard.  
57  
Viewing Pictures on a Computer  
3 Cautions  
• If a memory card containing a large number of images is inserted, there may be a delay before the software  
starts and you may be unable to import or save images. Use a memory card reader to transfer pictures.  
• Make sure that the computer does not display a message stating that copying is in progress and that the indica-  
tor lamp is out before turning the camera off or disconnecting the USB cable (if the number of images copied is  
very large, the indicator lamp may remain lit after the message has cleared from the computer display). Failure  
to observe this precaution could result in loss of data or damage to internal memory or the memory card.  
• Disconnect the camera before inserting or removing memory cards.  
• In some cases, it may not be possible to access pictures saved to a network server using the supplied software  
in the same way as on a standalone computer.  
• The user bears all applicable fees charged by the phone company or Internet service provider when using ser-  
vices that require an Internet connection.  
58  
Viewing Pictures on a Computer  
Disconnecting the Camera  
After confirming that the indicator lamp is out, follow the on-screen instructions to turn the camera off and  
disconnect the USB cable.  
Uninstalling the Supplied Software  
Only uninstall the supplied software when it is no longer required or before beginning reinstallation. After quitting  
the software and disconnecting the camera, open the control panel and use “Programs and Features” (Windows  
7/Windows Vista) or “Add or Remove Programs” (Windows XP) to uninstall MyFinePix Studio. One or more confir-  
mation dialogs may be displayed; read the contents carefully before clicking OK.  
59  
Using the Menus: Shooting Mode  
The shooting menu is used to adjust settings for a wide range of shooting conditions.  
Using the Shooting Menu  
Press MENU/OK to display the shoot-  
ing menu.  
Press the selector up or down to  
highlight the desired option.  
1
2
4
Press the selector up or down to  
highlight the desired menu item.  
Press MENU/OK to select the high-  
lighted option.  
5
6
Press the selector right to display op-  
tions for the highlighted item.  
Press DISP/BACK to exit to shooting  
mode.  
3
60  
Using the Menus: Shooting Mode  
Shooting Menu Options  
Menu item  
Descripption  
Opptions  
Default  
E/C/D/L/M/N/O/ SP1: C  
ASCENE POSITION  
Choose scenes for SP1 and SP2 modes (pg. 22).  
Choose a D shooting mode for I mode (pg. 27).  
Choose a C shooting mode for H mode (pg. 29).  
H/Q/R/S/F/U  
SP2: E  
ASHOOTING MODE  
(advanced D)  
ASHOOTING MODE  
(advanced C)  
V/X/W  
V
B/A  
A
a
Choose color reproduction options for pictures recorded us-  
ing X 2-COLOR (pg. 28).  
Choose the time lag for pictures recorded with B INTERVAL  
3D SHOOTING (pg. 31).  
Choose the order in which pictures are taken in H mode  
(pg. 30, 31).  
j2-COLOR SETTING  
k3D INTERVAL TIME  
lTURN  
a/b/c  
MIN. /1.0 /1.5 /2.0 /3.0 /5.0 /10  
G/H  
MIN.  
G
dSET SHUTTERSPEED,  
APERTURE.  
Adjust exposure for bright, dark, or high-contrast scenes in  
dSETTING APERTURE modes M, A, and P (pp. 24–26).  
dEXP. COMPENSATION  
AUTO (1600) /AUTO (800) /  
AUTO (400) /1600 /800 /400 / AUTO (800)  
Adjust ISO sensitivity (pg. 63). Choose higher values when the  
subject is poorly lit.  
NISO  
200 /100  
O 4 : 3 /O 3 : 2 /O 16 : 9 /  
P 4 : 3 /P 3 : 2 /P 16 : 9 /  
Q 4 : 3 /Q 3 : 2 /Q 16 : 9  
OIMAGE SIZE  
Choose image size and aspect ratio (pg. 64).  
Choose image quality (pg. 65).  
O 16 : 9  
TIMAGE QUALITY  
F /N  
N
61  
Using the Menus: Shooting Mode  
Menu item  
Descripption  
Opptions  
Default  
Shoot pictures in standard or saturated color or in black-and-  
white (pg. 65).  
PFINEPIX COLOR  
c/a/b  
>
DWHITE BALANCE  
RCONTINUOUS  
Adjust color for different light sources (pg. 66).  
Shoot a series of pictures (pg. 66).  
AUTO/i/j/k/l/m/n/g  
AUTO  
OFF  
J/I/OFF  
Choose whether the camera automatically detects and sets  
focus and exposure for human portrait subjects. Can be  
combined with red-eye removal (pg. 67).  
bFACE DETECTION  
ON /OFF  
OFF  
CPHOTOMETRY  
F2D AF MODE  
Choose how the camera meters exposure (pg. 68).  
Choose how the camera selects a focus area (pg. 68).  
o/p/q  
r/s  
o
r
iAUTO PARALLAX  
Choose ON for auto C parallax adjustment (pg. 15).  
ON/OFF  
ON  
CONTROL  
62  
Using the Menus: Shooting Mode  
NISO  
Control the camera’s sensitivity to light. Higher values can be used to reduce blur when lighting is  
poor; note, however, that mottling may appear in pictures taken at high sensitivities. If AUTO (1600),  
AUTO (800), or AUTO (400) is selected, the camera will adjust sensitivity automatically in response to  
shooting conditions. The maximum values that will be selected by the camera at settings of AUTO  
(1600), AUTO (800), and AUTO (400) are 1600, 800, and 400 respectively.  
1Note  
Sensitivity is not reset when the camera is turned off.  
63  
Using the Menus: Shooting Mode  
OIMAGE SIZZE  
Choose the size and aspect ratio at which still pic-  
tures are recorded. Large pictures can be printed  
at large sizes with no drop in quality; small pic-  
tures require less memory, allowing more pictures  
to be recorded.  
Aspect Ratio  
Pictures with an aspect ratio of 4:3 have the same  
proportions as the camera display. Pictures with an  
aspect ratio of 3:2 have the same proportions as a  
frame of 35-mm film, while an aspect ratio of 16:9 is  
suited to display on High Definition (HD) devices.  
Opption  
O 4 : 3  
O 3 : 2  
O 16 : 9  
P 4 : 3  
P 3 : 2  
P 16 : 9  
Q 4 : 3  
Q 3 : 2  
Q 16 : 9  
Prints at ssizes up tto  
31×23cm (12×9in.)  
31×21cm (12×8in.)  
30×17cm (12×7in.)  
22×16cm (9×6in.)  
22×15cm (9×6in.)  
22×12cm (9×5in.)  
17×13cm (7×5in.)  
17×11cm (7×4in.)  
16×9cm (6×4in.)  
4 : 3  
3 : 2  
16 : 9  
The number of pictures that can be taken at cur-  
rent settings (pg. 102) is shown in the monitor.  
1Note  
Image size is not reset when the camera is turned off or  
another shooting mode is selected.  
64  
Using the Menus: Shooting Mode  
TIMAGE QUALIITY  
PFINEPPIIX COLOR  
Choose how much image files are compressed. Enhance contrast and color saturation or take pic-  
Select FINE (low compression) for higher image tures in black and white.  
quality, NORMAL (high compression) to increase  
Opption  
Displaayed in  
Standard contrast and saturation.  
Recommended in most situations.  
the number of pictures that can be stored.  
cF-STANDARD  
Vivid contrast and color. Choose  
for vivid shots of flowers or en-  
hanced greens and blues in land-  
scapes. Not available in SP mode.  
aF-CHROME  
bF-B&W  
Take pictures in black and white.  
Settings other than cF-STANDARD are shown  
by an icon in the monitor.  
1Notes  
PFINEPIX COLOR is not reset when the camera is  
turned off or another shooting mode is selected.  
• Depending on the subject, the effects of aF-  
CHROME may not be visible in the monitor.  
65  
Using the Menus: Shooting Mode  
DWHITTEE BBALLANNCCE  
RCONTINNUOUS  
For natural colors, choose a setting that matches Capture motion in a series of pictures.  
the light source (for an explanation of “white bal- J TOP 40 (HIGH SPEED): The camera takes up to 40  
ance,” see the Glossary on page 101).  
pictures at high speed while the shutter button  
is pressed. Not available in C.  
I TOP 40: The camera takes up to 40 pictures  
while the shutter button is pressed.  
OFF: The camera takes one picture each time the  
shutter button is pressed.  
Opption  
AUTO  
i
Descripption  
White balance adjusted automatically.  
For subjects in direct sunlight.  
j
For subjects in the shade.  
k
Use under “daylight” fluorescent lights.  
Use under “warm white” fluorescent lights.  
Use under “cool white” fluorescent lights.  
Use under incandescent lighting.  
For underwater subjects in an aquarium.  
1Notes  
l
• The flash turns off automatically. The previously-se-  
lected flash mode is restored when OFF is selected  
for RCONTINUOUS.  
m
n
g
• Frame rate varies with shutter speed.  
If AUTO does not produce the desired results (for  
example, when taking close-ups), choose the op-  
tion that matches the light source.  
1Notes  
• Auto white balance is used with the flash. Turn the  
fl a s h o ff (pg. 35) to take pictures at other settings.  
• Results vary with shooting conditions. Play pictures  
back after shooting to check colors in the monitor.  
66  
Using the Menus: Shooting Mode  
bFACEE DETEECCTTIIOONN ((D Only)  
Intelligent Face Detection allows the camera to automatically detect human faces and set focus and  
exposure for a face anywhere in the frame for shots that emphasize portrait subjects. Choose for  
group portraits (in vertical or horizontal orientations) to prevent the camera from focusing on the back-  
ground.  
2 Tip: Intelligent Face Detection  
When Intelligent Face Detection is on, the selected face is indicated by a green border (note  
that, in some shooting modes, exposure is adjusted for the current shooting mode and may  
not be optimized for the selected subject). If more than one face is detected, the camera  
will select the face closest to the center of the frame; other faces are indicated by white bor-  
ders (note that some time may be required for face detection if the number of faces is very  
large). Intelligent Face Detection is recommended when using the self-timer for group- or  
self-portraits (pg. 38).  
Green border  
When a picture taken with Intelligent Face Detection is displayed, the camera can automatically select faces for  
red-eye removal (pg. 71), playback zoom (pg. 40), slide shows (pg. 70), printing (pg. 53), and cropping (pg. 73).  
3 Cautions  
• If no face is detected when the shutter button is pressed halfway (pg. 19), the camera will focus on the subject  
at the center of the display and red-eye will not be removed.  
• If the subject moves as the shutter button is pressed, their face may not be in the area indicated by the green  
border when the picture is taken.  
67  
Using the Menus: Shooting Mode  
CPHOTOMMETRY  
Choose how the camera meters exposure when This option controls how the camera selects the  
Intelligent Face Detection (pg. 67) is off. focus area when Intelligent Face Detection (pg.  
F2D AF MODE (D Only)  
o MULTI: Automatic scene recognition is used 67) is off. Regardless of the option selected, the  
to adjust exposure for a wide range of shooting camera will focus on the subject in the center of  
conditions.  
the monitor when macro mode is on (pg. 34).  
p SPOT: The camera meters lighting conditions r CENTER: The camera focuses on the subject in  
at the center of the frame. Recommended when  
the background is much brighter or darker than  
the center of the frame. This option can be used  
with focus lock (pg. 32).  
the main subject. Can be used with focus lock s MULTI: When the shutter button is pressed  
(pg. 32) to meter off-center subjects.  
halfway, the camera detects high-contrast sub-  
jects near the center of the frame and selects  
the focus area automatically (if the focus frame is  
not displayed, select r CENTER and use focus  
lock; pg. 32).  
q AVERAGE: Exposure is set to the average for  
the entire frame. Provides consistent exposure  
across multiple shots with the same lighting,  
and is particularly effective for landscapes and  
portraits of subjects dressed in black or white.  
M
Press  
halfway  
Focus frame  
68  
Using the Menus: Playback Mode  
The playback menu is used to manage the pictures in internal memory or on the memory card.  
Using the Playback Menu  
Playback Menu Options  
Opption  
Descripption  
Press the a button to enter play-  
1
Create copies of  
C
pictures with  
back mode.  
iPARALLAX CONTROL  
modified parallax (pg. 70).  
Press MENU/OK to display the play-  
back menu.  
AERASE  
ISLIDE SHOW  
Delete all or selected pictures (pg. 42).  
View pictures in a slide show (pg. 70).  
Create copies with reduced red eye (pg.  
71).  
Protect pictures from accidental dele-  
tion (pg. 72).  
2
BRED EYE REMOVAL  
DPROTECT  
Press the selector up or down to  
highlight the desired menu item.  
3
Create cropped copies of pictures (pg.  
73).  
Create small copies of pictures (pg. 74).  
Rotate pictures (pg. 75).  
Copy pictures between internal memo-  
ry and a memory card (pg. 76).  
Press the selector right to display op-  
tions for the highlighted item.  
GCROP  
4
ORESIZE  
CIMAGE ROTATE  
Press the selector up or down to  
highlight the desired option.  
5
ECOPY  
Select pictures for printing on DPOF-  
and PictBridge-compatible devices  
(pg. 52, 53).  
KPRINT ORDER  
Press MENU/OK to select the high-  
lighted option.  
6
(DPOF)  
Press DISP/BACK to exit to playback.  
7
69  
Using the Menus: Playback Mode  
iPARALLLAAXX CCOONNTTROOLL ((C Only)  
ISLIDE SHOW  
If the current picture is marked with a g icon to View pictures in an automated slide show. Choose  
indicate that it was taken in C, this option can be the type of show and press MENU/OK to start. Press  
used to create a copy with modified parallax.  
DISP/BACK at any time during the show to view on-  
screen help. When a movie is displayed, movie play-  
back will begin automatically, and the slide show  
will continue when the movie ends. The show can  
be ended at any time by pressing MENU/OK.  
Use the  
Q
control to adjust  
parallax (pg. 15), and then  
select iPARALLAX CON-  
TROL in the playback menu to  
display the options shown at  
Opption  
Displaayed in  
Press selector left or right to go back or  
skip ahead one frame. Select FADE-IN  
for fade transitions between frames.  
As above, except that camera automati-  
cally zooms in on faces selected with  
Intelligent Face detection.  
NORMAL  
right. Press MENU/OK to create a copy with modi-  
fi e d p a r a lla x .  
FADE-IN  
NORMAL g  
FADE-IN g  
MULTIPLE Display several pictures at once.  
3D FADE C images fade in from D to C.  
1Note  
The camera will not turn off automatically while a slide  
show is in progress.  
70  
Using the Menus: Playback Mode  
BRED EYE REMMOVAL (D Only)  
If the current picture is marked with a gicon to indicate that it was taken with Intel-  
ligent Face Detection, this option can be used to remove red-eye. Press MENU/OK to  
analyze the image; if red-eye is detected, the image will be processed to create a  
copy with reduced red-eye.  
1Notes  
• Red eye may not be removed if the camera is unable to detect a face or the face is in profile. Results may differ  
depending on the scene. Red eye can not be removed from pictures that have already been processed using  
red-eye removal or pictures created with other devices.  
• The amount of time needed to process the image varies with the number of faces detected.  
• Copies created with BRED EYE REMOVAL are indicated by a e icon during playback.  
71  
Using the Menus: Playback Mode  
DPROTECT  
Protect pictures from accidental deletion. The following options are available.  
FRAME  
Protect selected pictures.  
SET ALL  
Press MENU/OK to protect all  
pictures, or press DISP/BACK to  
exit without changing picture  
status.  
Press the selector left or right to dis-  
play the desired picture.  
1
RESET AALL  
Press MENU/OK to remove pro-  
tection from all pictures, or  
press DISP/BACK to exit without  
changing picture status.  
Picture not protected  
Protected picture  
Press MENU/OK to protect the picture.  
If the picture is already protected,  
pressing MENU/OK will remove pro-  
tection from the image.  
2
3
If the number of pictures affected is very large, a  
message will be displayed while the operation is  
in progress. Press DISP/BACK to exit before the op-  
eration is complete.  
Repeat steps 1–2 to protect addi-  
tional images. Press DISP/BACK to exit  
when the operation is complete.  
3 Caution  
Protected pictures will be deleted when the memory  
card or internal memory is formatted (pg. 82).  
72  
Using the Menus: Playback Mode  
GCROOP  
To create a cropped copy of a picture, play the picture back and select GCROP in the playback  
menu.  
Use the zoom control to zoom in and out and  
use the selector to scroll the picture until the  
desired portion is displayed (to exit to single-  
frame playback without creating a cropped  
copy, press DISP/BACK).  
Press MENU/OK to view the copy size.  
Larger crops produce larger copies;  
all copies have an aspect ratio of 4:3.  
1
2
3
Press MENU/OK to save the cropped  
copy to a separate file.  
Zoom indicator  
Navigation window  
shows portion of im-  
age currently displayed  
in monitor  
If the size of the final copy will be a, YES will  
be displayed in yellow.  
2 Tip: Intelligent Face Detection (D Only)  
If the picture was shot with In-  
telligent Face Detection (pg.  
67), gwill be displayed in the  
monitor. Press the selector  
down to zoom in on the se-  
lected face.  
73  
Using the Menus: Playback Mode  
ORESIZE  
To create a small copy of a picture, play the picture back and select ORESIZE in the playback menu.  
Press the selector up or down to high-  
light a STANDARD or b SMALL.  
Press MENU/OK to select the high-  
lighted option.  
1
2
3
Press MENU/OK to copy the picture at  
the selected size.  
74  
Using the Menus: Playback Mode  
CIMAGE ROOTATE (D Only)  
By default, pictures taken in tall orientation are  
displayed in wide orientation. Use this option to  
display pictures in the correct orientation in the  
monitor. It has no effect on pictures displayed on  
a computer or other device.  
Press the selector down to rotate the  
picture 90° clockwise, up to rotate  
the picture 90° counterclockwise.  
1
2
1Notes  
C images and protected pictures can not be rotat-  
ed. Remove protection before rotating D images  
(pg. 72).  
• The camera may not be able to rotate pictures cre-  
ated with other devices.  
To rotate a picture, play the picture back and se-  
lect CIMAGE ROTATE in the playback menu.  
Press MENU/OK to confirm the opera-  
tion (to exit without rotating the pic-  
ture, press DISP/BACK).  
The next time the picture is played back, it will  
automatically be rotated.  
75  
Using the Menus: Playback Mode  
ECOPY  
Copy pictures between internal memory and a memory card.  
Press the selector up or down to  
highlight a INTERNAL MEMORY  
y b CARD (copy from internal  
memory to the memory card) or b CARD y  
a INTERNAL MEMORY (copy from a memo-  
ry card to internal memory).  
Press the selector up or down to  
highlight FRAME or ALL FRAMES.  
1
3
Press MENU/OK.  
4
2 Tip: Copying Pictures Between Memory Cards  
To copy pictures between two memory cards, insert  
the source card and copy the pictures to internal mem-  
ory, then remove the source card, insert the destination  
card, and copy the pictures from internal memory.  
Press the selector right to display op-  
tions for the highlighted item.  
2
76  
Using the Menus: Playback Mode  
FRAME  
Copy selected frames.  
ALLL FFRRAAMESS  
Press MENU/OK to copy all pic-  
tures, or press DISP/BACK to exit  
without copying pictures.  
3 Cautions  
• Copying ends when the destination is full.  
• DPOF print information is not copied (pg. 53).  
Press the selector left or right to dis-  
play the desired picture.  
1
Press MENU/OK to copy the picture.  
2
3
Repeat steps 1–2 to copy additional  
images. Press DISP/BACK to exit when  
the operation is complete.  
77  
The Setup Menu  
Using the Setup Menu  
Display the setup menu.  
Adjust settings.  
1 1.1 Press  
2 2.1 Press the selector up or down  
MENU/OK to display the  
menu for the current mode.  
to highlight a menu item.  
1.2 Press the selector left to high-  
light the tab for the current  
menu.  
2.2Press the selector right to dis-  
play options for the highlighted  
item.  
1.3 Press the selector down to  
2.3 Press the selector up or down  
highlight the setup menu tab.  
to highlight an option.  
1.4 Press the selector right to dis-  
play the setup menu.  
2.4 Press MENU/OK to select the  
highlighted option.  
Exit.  
3 Press DISP/BACK to exit the menus.  
78  
The Setup Menu  
Setup Menu Options  
Menu item  
Descripption  
Set the camera clock (pg. 13).  
Set the clock to local time (pg. 81).  
Opptions  
h/g  
Default  
h
FDATE/TIME  
NTIME DIFFERENCE  
La  
Choose a language (pg.13).  
See page 105  
ENGLISH  
OFF  
Select ON in situations in which camera sounds or lights may be  
unwelcome (pg. 18).  
oSILENT MODE  
ON /OFF  
Reset all settings except FDATE/TIME, NTIME DIFFERENCE,  
O BACKGROUND COLOR, QVIDEO SYSTEM, and sDEMO  
MODE to default values. A confirmation dialog will be displayed,  
press the selector left or right to highlight OK and press MENU/OK.  
Format internal memory or memory cards (pg. 82).  
Choose how long pictures are displayed after shooting (pg. 82).  
Choose how files are named (pg. 83).  
Adjust the volume of camera controls.  
Adjust the volume of the shutter sound.  
Choose the sound made by the shutter.  
Press the selector up or down to adjust playback volume and press  
RRESET  
KFORMAT  
AIMAGE DISP.  
BFRAME NO.  
GOPERATION VOL.  
HSHUTTER VOLUME  
eSHUTTER SOUND  
3 SEC /1.5 SEC / ZOOM /OFF 1.5 SEC  
CONT. /RENEW  
b (high) /c (mid) /  
CONT.  
c
i
7
d (low) /eOFF (mute)  
i/j  
IPLAYBACK VOLUME  
MENU/OK to select.  
Press the selector up or down to adjust monitor brightness and  
press MENU/OK to select.  
JLCD BRIGHTNESS  
0
MAUTO POWER OFF  
BRED EYE REMOVAL  
DDIGITAL ZOOM  
qOPT AXIS CONTROL  
o3DREC  
Choose the auto power off delay (pg. 84).  
Turn red-eye removal on or off (pg. 36).  
Enable or disable digital zoom (pg. 84).  
Align the optical axes of the twin lenses (pg. 85).  
Choose MPO+JPEG to save JPEG copies of C images (pg. 85).  
5 MIN /2 MIN /OFF  
ON /OFF  
ON /OFF  
MPO+JPEG /MPO  
2 MIN  
OFF  
OFF  
0
MPO+JPEG  
79  
The Setup Menu  
Menu item  
Descripption  
Opptions  
Default  
OFF  
Choose whether to save unprocessed copies of pictures taken ON  
selected for BRED EYE REMOVAL (pg. 79).  
nSAVE ORG IMAGE  
ON /OFF  
OBACKGROUND COLOR Choose a color scheme for menus and cursors.  
cGUIDANCE DISPLAY Choose whether to display tool tips.  
ON /OFF  
ON  
Disable C to prevent fatigue or display a warning after 30 min-  
utes of use (pg. 85).  
r3D CAUTION DISP  
ON /OFF /NOT 3D  
ON  
QVIDEO SYSTEM  
wHDMI OUTPUT  
Choose a video mode for connection to a TV.  
Choose a display format for output to HDMI devices (pg. 83).  
NTSC /PAL  
3D /SIDE-BY-SIDE /2D  
3D  
Optimize camera performance for increased battery life or quick  
focus (pg. 14).  
SPOWER MANAGEMENT  
v/w/p  
v
If ON is selected when the camera is powered by an AC power  
adapter, a demo will play when the camera is turned on. Press the  
shutter button to exit demo mode.  
sDEMO MODE  
ON /OFF  
ON  
80  
The Setup Menu  
NTIME DIFFFERENCE  
When traveling, use this option to switch the camera clock instantly from your home time zone to the  
local time at your destination.  
Specify the difference between local time  
Switch between local time and your home  
1 and your home time zone.  
2 time zone.  
To set the camera clock to local time, high-  
light g LOCAL and press MENU/OK. To set  
the clock to the time in your home time  
zone, select h HOME. If g LOCAL is se-  
lected, g will be displayed in the monitor  
for three seconds after the camera enters  
shooting mode, and the date will be dis-  
played in yellow.  
1.1 Press the selector up or down  
to highlight g LOCAL.  
1.2 Press the selector right to dis-  
play the time difference.  
1.3 Press the selector left or right  
to highlight +, , hours, or min-  
utes; press up or down to edit.  
The minimum increment is 15 minutes.  
3D  
1.4 Press MENU/OK when settings  
are complete.  
After changing time zones, check that the  
date and time are correct.  
81  
The Setup Menu  
KFORMAT  
AIMAGEE DIISSP.  
Format internal memory or a memory card. If a Choose how long pictures are displayed in the  
memory card is inserted in the camera, this op- monitor after shooting.  
tion will format the memory card. If no memory 3 SEC/1.5 SEC: Pictures are displayed for the speci-  
card is inserted, a will be displayed in the format  
dialog and this option will format internal mem-  
ory. Press the selector left to highlight OK and  
press MENU/OK to begin formatting.  
fied time before being recorded to the memory  
card. Colors may differ from those in the final  
picture.  
ZOOM (CONTINUOUS): Pictures are displayed until  
the MENU/OK button is pressed. Pictures can be  
zoomed in to check fine details. Not available  
in C or I mode or when an option oth-  
er than OFF is selected for RCONTINUOUS  
(pg. 66).  
3 Cautions  
• All data—including protected pictures—will be de-  
leted. Be sure important files have been copied to a  
computer or other storage device.  
• Do not open the battery-chamber cover during for-  
matting.  
OFF: Pictures are not automatically displayed af-  
ter shooting.  
82  
The Setup Menu  
BFRAME NO.  
wHDMII OOUTPUT  
Choose a display format for output to HDMI de-  
vices.  
3D: Choose for output to devices that support  
3D display.  
SIDE-BY-SIDE: Choose for output to devices that  
support side-by-side 3D display. Be sure to con-  
figure the television for side-by-side display as  
described in the television manual.  
Frame number  
New pictures are stored in im-  
age files named using a four-  
digit file number assigned  
by adding one to the last file  
number used. The file num-  
ber is displayed during playback as shown at  
right. BFRAME NO. controls whether file num-  
bering is reset to 0001 when a new memory card  
100-0001  
Directory  
number  
File  
number  
is inserted or the current memory card or internal 2D: Choose for output to High Definition (HD)  
memory is formatted.  
devices.  
CONTINUOUS: Numbering continues from the last  
file number used or the first available file num-  
ber, whichever is higher. Choose this option to  
reduce the number of pictures with duplicate  
fi le n a m e s .  
RENEW: Numbering is reset to 0001 after format-  
ting or when a new memory card is inserted.  
1Notes  
• If the frame number reaches 999-9999, the shutter  
release will be disabled (pg. 98).  
• Selecting RRESET (pg. 79) resets BFRAME NO. to  
CONTINUOUS but does not reset frame numbering.  
• Frame numbers for pictures taken with other cam-  
eras may differ.  
83  
The Setup Menu  
MAUTO POWWEERR OFFF  
DDIGITAL ZZOOM (D Only)  
Choose the length of time before the camera If ON is selected, selecting i at the maximum  
turns off automatically when no operations are optical zoom position will trigger digital zoom,  
performed. Shorter times increase battery life; if further magnifying the image. To cancel digital  
OFF is selected, the camera must be turned off zoom, zoom out to the minimum digital zoom  
manually (note that the camera will turn off au- position and select j.  
tomatically after five minutes if p QUICK AF is  
selected for SPOWER MANAGEMENT or if the  
Zoom  
camera enters standby while in movie mode). Re-  
indicator  
gardless of the option selected, the camera will  
not turn off automatically when connected to a  
printer (pg. 49) or computer (pg. 57) or when a  
slide show is in progress (pg. 70).  
Zoom indicator,  
DIGITAL ZOOM off  
Zoom indicator,  
DIGITAL ZOOM on  
j
i j  
i
2 Tip: Reactivating the Camera  
To reactivate the camera after it has turned off auto-  
matically, open the lens cover or press the abutton  
for about a second (pg. 12).  
Optical zoom  
Optical zoom  
Digital  
zoom  
3 Caution  
Digital zoom produces lower quality images than opti-  
cal zoom.  
84  
The Setup Menu  
qOPT AXIS CONTROOLL  
r3D CAUTIOON DIISP  
Reposition the lenses to verti-  
cally align their optical axes for  
C photography. A setting  
of 0 is recommended in most  
circumstances; to choose a dif-  
To prevent fatigue, C can be disabled or a warn-  
ing can be displayed after prolonged use.  
ON: C enabled, but a warning is displayed after  
30 minutes of continuous use (measured from  
when this option is selected or the start of C  
display).  
ferent setting, press the selector up or down and  
press MENU/OK to select. Positive values raise the OFF: C enabled with no warning displayed af-  
left lens.  
ter prolonged use.  
NOT 3D DISP: C disabled.  
o3DREC  
Choose MPO to save C images in multi-picture  
(MPO) format, MPO+JPEG to save a JPEG copy in  
addition to the multi-picture file. For information  
on file formats, see the Glossary on page 100.  
1Note  
MPO files can not be printed in D (pg. 49). The sup-  
plied MyFinePix Studio is required to view MPO files on  
a computer (pg. 55).  
85  
Optional Accessories  
The camera supports a wide range of accessories from FUJIFILM and other manufacturers.  
Computer Related  
Digitaall VViewers  
Note: DirectX 8.0 runtime required to view  
movies (Windows only). Movies must be cop-  
ied to computer before viewing.  
FINEPIX  
REAL 3D W3  
FinePix REAL 3D V1  
(sold separately)  
USB cable (supplied)  
Auddiioo//VVisual  
SD card slot or card reader  
A/V cable (sold separately)  
SD/SDHC  
memory card  
Computer (available from  
third-party suppliers)  
Standard TV (available from  
third-party suppliers)  
Printing  
USB cable  
(supplied; D  
HDMI cable (sold separately)  
images only)  
3D HDTV (available from  
third-party suppliers)  
PictBridge-compatible printer  
(available from third-party suppliers)  
HDMI cable (sold separately)  
HDMI cable  
(sold separately)  
Printer (available from  
third-party suppliers)  
HDP-L1  
HD player  
HDTV (available from  
third-party suppliers)  
86  
Optional Accessories  
Accessories from FUJIFILM  
The following optional accessories are available from FUJIFILM. For the latest information on the acces-  
sories available in your region, check with your local FUJIFILM representative or visit http://www.fujifilm.  
com/products/digital_cameras/index.html.  
Rechhaarggeeaablle  
Li-ion batteriies  
Additional NP-50 rechargeable batteries can be  
purchased as required.  
NP-50  
Replacement battery chargers can be purchased as  
required. The BC-45W charges an NP-50 battery in  
about 150 minutes at +20°C (+68°F).  
Batttteerryy cchhaarrgeers BC-45W  
Use for extended playback or when copying pic-  
tures to a computer (shape of adapter and plug  
vary with region of sale).  
AC-5VX (requires CP-50  
DC coupler)  
AC power addaaptters  
DC coouuplers  
CP-50 (for use with AC-5VX  
AC power adapter)  
Connect the AC-5VX to the camera.  
HDP-L1 (requires HDMI  
cable, available from third-  
party suppliers)  
Connect to a High Definition (HD) TV to view pho-  
tographs and movies from SD memory cards.  
HD players  
AV cables  
AVC-1  
Connect the camera to video devices.  
87  
Caring for the Camera  
To ensure continued enjoyment of the product, observe the following precautions.  
Sttorage aanndd UUse  
Condeennssatioonn  
If the camera will not be used for an extended pe-  
riod, remove the battery and memory card. Do  
not store or use the camera in locations that are:  
• exposed to rain, steam, or smoke  
• very humid or extremely dusty  
• exposed to direct sunlight or very high tempera-  
tures, such as in a closed vehicle on a sunny day  
• extremely cold  
Sudden increases in temperature, such as occur  
when entering a heated building on a cold day,  
can cause condensation inside the camera. If this  
occurs, turn the camera off and wait an hour be-  
fore turning it on again. If condensation forms on  
the memory card, remove the card and wait for  
the condensation to dissipate.  
Cleaning  
• subject to strong vibration  
Use a blower to remove dust from the lens and  
monitor, then gently wipe with a soft, dry cloth.  
Any remaining stains can be removed by wiping  
gently with a piece of FUJIFILM lens-cleaning pa-  
per to which a small amount of lens-cleaning fluid  
has been applied. Care should be taken to avoid  
scratching the lens or monitor. The camera body  
can be cleaned with a soft, dry cloth. Do not use  
alcohol, thinner, or other volatile chemicals.  
• exposed to strong magnetic fields, such as near  
a broadcasting antenna, power line, radar emit-  
ter, motor, transformer, or magnet  
• in contact with volatile chemicals such as pesti-  
cides  
• next to rubber or vinyl products  
Water and Saannd  
Exposure to water and sand can also damage the  
camera and its internal circuitry and mechanisms.  
When using the camera at the beach or seaside,  
avoid exposing the camera to water or sand. Do  
not place the camera on a wet surface.  
Traveling  
Keep the camera in your carry-on baggage.  
Checked baggage may suffer violent shocks that  
could damage the camera.  
88  
Troubleshooting  
Power and Battery  
Problem  
Possiblle cause  
The battery is exhausted.  
Solluution  
Charge the battery or insert a fully-charged  
spare battery.  
Page  
5, 6  
The battery is not in the correct orientation. Reinsert the battery in the correct orientation.  
The battery-chamber cover is not latched. Latch the battery-chamber cover.  
6
6–7  
The camera does  
not turn on.  
The AC power adapter and DC coupler are Make sure that the AC power adapter and DC  
8
not connected properly.  
The battery is cold.  
coupler are properly connected.  
Warm the battery by placing it in a pocket or  
other warm place and re-insert it in the camera vi  
immediately before taking a picture.  
Power  
supply  
There is dirt on the battery terminals.  
Clean the terminals with a soft, dry cloth.  
The battery has reached the end of its charging  
life. Purchase a new battery.  
The battery runs  
down quickly.  
The battery has been charged many times.  
p QUICK AF is selected for SPOWER Select a power saving option to reduce the  
80  
5, 6  
8
MANAGEMENT.  
drain on the battery.  
Charge the battery or insert a fully-charged  
spare battery.  
The battery is exhausted.  
The camera turns  
off suddenly.  
The AC power adapter or DC coupler has Make sure that the AC power adapter and DC  
been disconnected.  
coupler are properly connected.  
The battery is not correctly inserted.  
The battery is not in the correct orientation. Reinsert the battery in the correct orientation.  
Reinsert the battery in the charger.  
5
5
Charging does  
not start.  
Charging is slow. The temperature is low.  
Charge the battery at room temperature.  
Clean the terminals with a soft, dry cloth.  
The battery has reached the end of its charging  
vi  
Battery  
charger  
There is dirt on the battery terminals.  
The charging  
lamp lights, but  
the battery does  
not charge.  
The battery has been charged many times. life. Purchase a new battery. If the battery still vi  
fails to charge, contact your FUJIFILM dealer.  
89  
Troubleshooting  
Menus and Displays  
Problem  
Menus and displays are not English is not selected for the La  
Possiblle cause  
Solluution  
Solluution  
Page  
Select ENGLISH.  
79  
in English.  
option in the setup menu.  
C/D  
Problem  
Possiblle cause  
Page  
NOT 3D DISP is selected for r3D CAU-  
TION DISP .  
C mode not available.  
Select OFF or ON.  
85  
C display not available in v POWER SAVE 1 is selected for SPOW-  
Select another power management option.  
80  
C mode.  
ER MANAGEMENT.  
Shooting  
Problem  
Possiblle cause  
Solluution  
Page  
Memory is full.  
Memory is not formatted.  
Insert a new memory card or delete pictures. 9, 42  
Format the memory card or internal memory. 82  
There is dirt on the memory card contacts. Clean the contacts with a soft, dry cloth.  
9
No picture is taken  
when the shutter  
button is pressed.  
The memory card is damaged.  
Insert a new memory card.  
Taking  
pictures  
Charge the battery or insert a fully-charged  
spare battery.  
The battery is exhausted.  
5, 6  
12  
The camera has turned off automatically. Turn the camera on.  
The monitor goes  
dark after shoot- The flash has fired.  
ing.  
The monitor may darken while the flash  
charges. Wait for the flash to charge.  
19  
The subject is close to the camera.  
The subject is far away from the camera.  
The subject is not suited to autofocus.  
Select macro mode.  
Cancel macro mode.  
Use focus lock.  
34  
32  
The camera does  
not focus.  
Focus  
90  
Troubleshooting  
Problem  
Possiblle cause  
Solluution  
Page  
The flash is not available in the current  
shooting mode.  
Choose a different shooting mode.  
22  
Charge the battery or insert a fully-charged  
spare battery.  
The battery is exhausted.  
5, 6  
66  
The flash does  
not fire.  
An option other than OFF is selected for  
RCONTINUOUS.  
Turn RCONTINUOUS off.  
The camera is in silent mode.  
The flash is off (P).  
Turn silent mode off.  
Choose a different flash mode.  
18  
35  
Flash  
The desired flash mode is not available in  
the current shooting mode.  
The camera is in silent mode.  
Choose a different shooting mode.  
22  
Flash mode not  
available.  
Turn silent mode off.  
18  
The flash does  
not fully light the  
subject.  
Face detection  
not available.  
The subject is not in range of the flash.  
Position the subject in range of the flash.  
104  
The flash window is obstructed.  
Hold the camera correctly.  
17  
22  
Intelligent Face Detection is not available in  
the current shooting mode.  
Choose a different shooting mode.  
The subject’s face is obscured by sunglass-  
es, a hat, long hair, or other objects.  
Remove the obstructions.  
The subject’s face occupies only a small Change the composition so that the subject’s  
area of the frame. face occupies a larger area of the frame.  
The subject’s head is at an angle or the sub- Ask the subject to face the camera and hold  
Intelligent  
Face  
Detection  
No face is de-  
tected.  
ject is not facing the camera.  
their head straight.  
The camera is tilted.  
The subject’s face is poorly lit.  
Hold the camera straight.  
Shoot in bright light.  
17  
Wrong subject  
selected.  
The selected subject is closer to the center Recompose the picture or turn face detection  
of the frame than the main subject. off and frame the picture using focus lock.  
32  
91  
Troubleshooting  
Problem  
Possiblle cause  
Solluution  
Page  
Macro mode is  
not available.  
Macro mode is not available in the current  
shooting mode.  
Close-ups  
Choose a different shooting mode.  
22  
The lens is dirty.  
The lens is blocked.  
Clean the lens.  
Keep objects away from the lens.  
88  
17  
Pictures are  
blurred.  
s is displayed during shooting and the  
focus frame is displayed in red.  
k is displayed during shooting.  
Check focus before shooting.  
Use the flash or a tripod.  
96  
35  
Problem  
images  
Pictures are  
mottled.  
Slow shutter speed selected when ambient This is characteristic of CCD image sensors  
temperature is high. and does not indicate a malfunction.  
Vertical lines ap- The camera has been used continuously at Turn the camera off and wait for it to cool  
pear in pictures. high temperatures.  
down.  
Turn the camera off before connecting the AC  
power adapter/DC coupler. Leaving the cam-  
era on can result in corrupted files or damage  
to the memory card or internal memory.  
Pictures are not  
recorded.  
Recording  
Power was interrupted during shooting.  
92  
Troubleshooting  
Playback  
Problem  
Possiblle cause  
Solluution  
Page  
The pictures were taken with a different make  
or model of camera.  
The pictures were created using ORESIZE  
Pictures are grainy.  
Pictures  
Playback zoom  
unavailable.  
40  
79  
or with a different make or model of camera.  
Playback volume is too low.  
The microphone was obstructed.  
The speaker is obstructed.  
Adjust playback volume.  
Hold the camera correctly during recording.  
Hold the camera correctly during playback.  
No sound in  
movie playback.  
Movies  
Selected pictures Some of the pictures selected for deletion are Remove protection using the device with  
Deletion  
72  
are not deleted. protected.  
which it was originally applied.  
Connections  
Problem  
Possiblle cause  
Solluution  
Page  
The camera is not properly connected.  
Connect the camera correctly.  
47, 48  
An A/V cable was connected during movie Connect the camera once movie playback  
46, 47  
playback.  
has ended.  
No picture or  
sound.  
Input on the television is set to “TV”.  
Set input to “VIDEO”.  
TV  
The camera is not set to the correct video Match the camera QVIDEO SYSTEM set-  
80  
standard.  
ting to the TV.  
The volume on the television is too low.  
Adjust the volume.  
The camera is not set to the correct video Match the camera QVIDEO SYSTEM set-  
standard. ting to the TV.  
No color.  
80  
93  
Troubleshooting  
Problem  
Possiblle cause  
Solluution  
Page  
The pictures were created using H or  
MyFinePix Studio, were modified using  
iPARALLAX CONTROL, or are cropped or  
resized copies of C photos.  
2D is selected for wHDMI OUTPUT in the  
camera setup menu.  
The pictures described at left can not be dis-  
played in C. This is normal and does not 48  
indicate a malfunction.  
C pictures are  
not displayed  
in 3D  
3D TV  
Select another wHDMI OUTPUT option.  
83  
Television is not configured for 3D display.  
Adjust TV controls.  
The computer  
Computer does not recog- The camera is not properly connected.  
Connect the camera correctly.  
57–59  
nize the camera.  
The camera is not properly connected.  
The printer is off.  
Connect the camera correctly.  
Turn the printer on.  
49  
Pictures can not  
be printed.  
Only one copy is  
printed.  
The date is not  
printed.  
PictBridge  
The printer is not PictBridge-compatible.  
80  
AC power Demo slides are  
adapter displayed.  
Press the shutter button to exit demo and  
select OFF for sDEMO MODE.  
ON is selected for sDEMO MODE.  
94  
Troubleshooting  
Miscellaneous  
Problem  
Possiblle cause  
Solluution  
Page  
Remove and reinsert the batteries or discon-  
nect and reconnect the AC power adapter/DC 6–7, 8  
coupler.  
Temporary camera malfunction.  
Nothing happens  
when the shutter but-  
ton is pressed.  
Charge the battery or insert a fully-charged  
The battery is exhausted.  
5, 6  
spare battery.  
Remove and reinsert the battery or discon-  
The camera does not  
function as expected.  
nect and reconnect the AC power adapter/DC  
coupler. If the problem persists, contact your  
FUJIFILM dealer.  
Turn silent mode off.  
Temporary camera malfunction.  
The camera is in silent mode.  
6–7, 8  
No sound.  
18  
95  
Warning Messages and Displays  
The following warnings are displayed in the monitor:  
Warning  
Descripption  
Solluution  
B (red)  
The battery is low.  
A (blinks red) The battery is exhausted.  
Charge the battery or insert a fully-charged spare bat-  
tery.  
k
Slow shutter speed. Picture may be blurred. Use the flash or mount the camera on a tripod.  
• Use focus lock to focus on another subject at the  
same distance, then recompose the picture (pg. 32).  
• If the subject is poorly lit, try focusing at a distance of  
about 2m (6.6ft.).  
s
(displayed in red The camera can not focus.  
with red focus frame)  
• Use macro mode to focus when taking close-ups.  
Aperture or shutter The subject is too bright or too dark. The pic-  
speed shown in red ture will be over- or under-exposed.  
If the subject is dark, use the flash.  
G
Lens is obstructed by a finger or other object. Remove the obstruction.  
FOCUS ERROR  
ZOOM ERROR  
LENS CONTROL ERROR  
Turn the camera off and then on again, taking care not  
to touch the lens. If the message persists, contact a  
FUJIFILM dealer.  
Camera malfunction.  
No memory card inserted when ECOPY is  
selected in the playback menu.  
NO CARD  
Insert a memory card.  
The memory card or internal memory is not Format the memory card or internal memory using  
formatted or the memory card was formatted the KFORMAT option in the camera setup menu  
in a computer or other device.  
(pg. 82).  
CARD NOT INITIALIZED  
Clean the contacts with a soft, dry cloth. If the mes-  
The memory card contacts require cleaning. sage is repeated, format the memory card (pg. 82). If  
the message persists, replace the memory card.  
Camera malfunction.  
Contact a FUJIFILM dealer.  
PROTECTED CARD  
BUSY  
The memory card is locked.  
The memory card is incorrectly formatted.  
Unlock the memory card (pg. 9).  
Use the camera to format the memory card (pg. 82).  
96  
Warning Messages and Displays  
Warning  
Descripption  
Solluution  
The memory card is not formatted for use in  
the camera.  
Format the memory card (pg. 82).  
Clean the contacts with a soft, dry cloth. If the mes-  
sage is repeated, format the memory card (pg. 82). If  
the message persists, replace the memory card.  
The memory card contacts require cleaning or  
the memory card is damaged.  
CARD ERROR  
Incompatible memory card.  
Camera malfunction.  
Use a compatible memory card.  
Contact a FUJIFILM dealer.  
b MEMORY FULL  
a MEMORY FULL  
The memory card or internal memory is full; Delete pictures or insert a memory card with more free  
pictures can not be recorded or copied.  
Memory card error or connection error.  
space.  
INTERNAL MEMORY IS FULL  
INSERT A NEW CARD  
Re-insert the memory card or turn the camera off  
and then on again. If the message persists, contact a  
FUJIFILM dealer.  
WRITE ERROR  
READ ERROR  
Not enough memory remaining to record ad- Delete pictures or insert a memory card with more free  
ditional pictures.  
space.  
The memory card or internal memory is not  
formatted.  
Format the memory card or internal memory (pg. 82).  
The file is corrupt or was not created with the  
camera.  
The file can not be played back.  
Clean the contacts with a soft, dry cloth. If the mes-  
The memory card contacts require cleaning. sage is repeated, format the memory card (pg. 82). If  
the message persists, replace the memory card.  
Camera malfunction.  
Contact a FUJIFILM dealer.  
97  
Warning Messages and Displays  
Warning  
Descripption  
Solluution  
Format the memory card and select RENEW for the  
The camera has run out of frame numbers (cur- BFRAME NO. option in the set-up menu. Take a pic-  
FRAME NO. FULL  
rent frame number is 999-9999).  
ture to reset frame numbering to 100-0001, then return  
to the BFRAME NO. menu and select CONTINUOUS.  
Date for which more than 4,999 pictures exist  
selected in sort-by-date view.  
TOO MANY FRAMES  
Choose a different date.  
FCAN NOT EXECUTE  
m CAN NOT EXECUTE  
Red-eye removal can not be applied to the se-  
lected picture or movie.  
An attempt was made to delete or rotate a pro-  
tected picture.  
PROTECTED FRAME  
Remove protection before deleting or rotating pictures.  
Select a different source.  
b NO IMAGE  
a NO IMAGE  
The source device selected in the playback  
ECOPY menu contains no pictures.  
aCAN NOT CROP  
An attempt was made to crop a apicture.  
These pictures can not be cropped.  
The picture selected for cropping is damaged  
or was not created with the camera.  
CAN NOT CROP  
The DPOF print order on the current memory Copy the pictures to internal memory and create a new  
DPOF FILE ERROR  
CAN NOT SET DPOF  
card contains more than 999 images.  
print order.  
The picture can not be printed using DPOF.  
FCAN NOT SET DPOF Movies can not be printed using DPOF.  
CAN NOT ROTATE The picture can not be rotated.  
FCAN NOT ROTATE Movies can not be rotated.  
98  
Warning Messages and Displays  
Warning  
Descripption  
Solluution  
PRESS AND HOLD  
An attempt was made to choose a flash mode  
Exit silent mode before choosing a flash mode or ad-  
justing the volume.  
THE DISP BUTTON TO or adjust the volume with the camera in silent  
DEACTIVATE SILENT MODE mode.  
A connection error occurred while pictures  
COMMUNICATION ERROR were being printed or copied to a computer or  
other device.  
Confirm that the device is turned on and that the USB  
cable is connected.  
Check printer (see printer manual for details). To resume  
printing, turn the printer off and then turn it back on.  
PRINTER ERROR  
Printer out of paper or ink, or other printer er-  
ror.  
PRINTER ERROR  
RESUME?  
Check printer (see printer manual for details). If printing  
does not resume automatically, press MENU/OK to resume.  
Movies and some pictures created with other devices  
An attempt was made to print a movie, a pic- can not be printed. If the picture was created with the  
CAN NOT BE PRINTED ture not created with the camera, or a picture camera, check the printer manual to confirm that the  
in a format not supported by the printer.  
printer supports the JFIF-JPEG or Exif-JPEG format. If it  
does not, the pictures can not be printed.  
99  
Glossary  
3D movie format: FUJIFILM has extended the generic Motion JPEG format to create an AVI movie file format that  
supports 3D. 3D movie files have the extension “*.AVI” and can be played back on the camera in 3D with stereo  
sound. When viewed in Windows Media Player, only the images recorded with the left lens will be displayed.  
Digital zoom: Unlike optical zoom, digital zoom does not increase the amount of visible detail. Instead, details vis-  
ible using optical zoom are simply enlarged, producing a slightly “grainy” image.  
DPOF (Digital Print Order Format): A standard that allows pictures to be printed from “print orders” stored  
in internal memory or on a memory card. The information in the order includes the pictures to be  
printed and the number of copies of each picture.  
EV (Exposure Value): The exposure value is determined by the sensitivity of the image sensor and the amount  
of light that enters the camera while the image sensor is exposed. Each time the amount of light doubles, EV  
increases by one; each time the amount of light is halved, EV decreases by one. The amount of light entering the  
camera can be controlled by adjusting aperture and shutter speed.  
Exif Print: A standard that allows information stored with pictures to be used for optimal color reproduction dur-  
ing printing.  
JPEG (Joint Photographic Experts Group): A compressed file format for color images. The higher the compression  
rate, the greater the loss of information and more noticeable drop in quality when the picture is displayed.  
Motion JPEG: An AVI (Audio Video Interleave) format that stores sound and JPEG images in a single file. Motion JPEG  
files can be viewed on a computer using Windows Media Player (requires DirectX 8.0 or later).  
Multi-picture format: An image file format that allows multiple images to be stored in a single file. This camera  
stores 3D images in multi-picture files with the extension “*.MPO”.  
100  
Glossary  
Parallax: Changes in the apparent position and orientation of a subject when viewed from different angles.  
Smear: A phenomenon specific to CCDs which causes white streaks to appear when very bright light sources, such  
as the sun or reflected sunlight, appear in the frame.  
White balance: The human brain automatically adapts to changes in the color of light, with the result that objects  
that appear white under one light source still appear white when the color of the light source changes. Digital  
cameras can mimic this adjustment by processing images according to the color of the light source. This process  
is known as “white balance.”  
101  
Internal Memory/Memory Card Capacity  
The following table shows the file size and recording time or number of available frames at different  
image sizes (the figures for capacity assume that MPO+JPEG is selected for o3DREC as described  
on page 85; multiply by about 1.5 for MPO-only files and by about 3 for 2D images). All figures are ap-  
proximate; file size varies with the scene recorded, producing wide variations in the number of files that  
can be stored. The number of exposures or length remaining may not diminish at an even rate.  
Capacity  
Inteerrnnaall mmemory  
(approx.. 34 MB)  
FINE NORMAL  
4 GB  
8 GB  
File size  
MPO  
Image/fraammee ssiizzee  
O4 : 3  
FINE  
260  
370  
530  
710  
NORMAL  
530  
730  
1040  
1400  
1630  
1880  
FINE  
530  
740  
1060  
1430  
1680  
2510  
NORMAL MPO+JJPPEG  
JPEG  
4.9MB  
3.6MB  
2.5MB  
1.8MB  
1.6MB  
1.0MB  
2
3
4
6
1070  
1470  
2090  
2820  
3270  
3770  
14.7MB  
10.7MB  
7.5MB  
5.5MB  
4.7MB  
3.1MB  
9.8MB  
7.1MB  
5.0MB  
3.7MB  
3.1MB  
2.1MB  
O16 : 9  
P4 : 3  
P16 : 9  
Q4 : 3  
4
8
6
7
10  
12  
14  
16  
830  
1250  
Q16 : 9  
j*  
26sec.  
46sec.  
10min.  
27min.  
50min.  
20min.  
50min.  
87min.  
21min.  
54min.  
100min.  
42min.  
100min.  
176min.  
C f†  
g†  
j†  
D f†  
g†  
* When a movie reaches a size of 4GB, recording will briefly pause and then resume in a new file. The recording times displayed  
by the camera assume a maximum file size of about 4GB.  
Total length of all movie files. Individual movies can not exceed 2GB, regardless of capacity of memory card.  
102  
Specifications  
System  
Model  
FinePix REAL 3D W3  
Effective pixels  
CCD  
10.17 million  
Two 1 2.3 -in. CCDs  
/
Storage media  
File system  
• Internal memory (approx. 34MB)  
Compliant with Design Rule for Camera File System (DCF), Exif 2.3, multi-picture format (MPO), and  
Digital Print Order Format (DPOF)  
• SD/SDHC memory cards (see page 9)  
File format  
Still pictures (C): MPO+JPEG or MPO  
Still pictures (D): Exif 2.3 JPEG (compressed)  
Movies (C): Stereo AVI with 2 image channels  
Movies (D): Motion JPEG with stereo audio recorded in AVI  
Image size (pixels;  
fi le s iz e )  
O4 : 3: 3,648×2,736 (10M)  
P4 : 3: 2,592×1,944 (5M)  
Q4 : 3: 2,048×1,536 (3M)  
O3 : 2: 3,648×2,432 (8.9M)  
P3 : 2: 2,592×1,728 (4.5M)  
Q3 : 2: 2,016×1,344 (2.7M)  
O16 : 9: 3,584×2,016 (7.2M)  
P16 : 9: 2,560×1,440 (3.7M)  
Q16 : 9: 1,920×1,080 (2M)  
Lens  
Two Fujinon 3× optical zoom lenses, F/3.7 (wide angle)4.2 (telephoto)  
Focal length  
f=6.3mm–18.9mm (35-mm format equivalent: 35 mm–105 mm)  
Zoom  
C/I: Combined optical and digital zoom up to approx. 3.8× (35-mm format equivalent: 39 mm–149 mm)  
H: 3× optical zoom  
D: 3× optical zoom with up to approx. 5.7× digital zoom (maximum combined zoom approx. 17.1 ×)  
Digital zoom  
Approx. 5.7× (up to 17.1 × when combined with optical zoom)  
Aperture  
F3.7/F5.0/F8.0 (wide angle), F4.2/F5.6/F9.0 (telephoto)  
Focus range (distance  
from front of lens)  
Approx. 60cm (2.0ft.)–infinity  
Macro (D): Approx. 8cm–80cm/0.3ft.–2.6ft. (wide angle); 60cm–3m/2.0ft.–9.8ft. (telephoto)  
Macro (C): Approx. 38cm–70cm/1.2ft.–2.3ft. (wide angle); 1.1m–2.3m/3.6ft.–7.5ft. (telephoto)  
Quick AF: Approx. 1m (3.3ft.)–infinity  
Recommended shooting Auto parallax off: Approx. 1.3m/4.3ft.–infinity (wide angle); 4.1m/13.5ft.–infinity (telephoto)  
distance (C) Auto parallax on (as measured by FUJIFILM): Approx. 1.3m/4.3ft.–infinity (wide angle); 4.1m/13.5ft.–infinity (telephoto)  
103  
Specifications  
System  
Sensitivity  
Metering  
Exposure control  
Standard output sensitivity equivalent to ISO 100, 200, 400, 800, 1600; AUTO (400), AUTO (800), AUTO (1600)  
256-segment through-the-lens (TTL) metering; MULTI, SPOT, AVERAGE  
Program and aperture-priority autoexposure; manual exposure  
/
Exposure compensation 2EV+2EV in increments of 1 3 EV (P and A modes)  
Scene modes  
E(ANTI-BLUR), C(NATURAL AND FLASH LIGHTING; in C mode, images are recorded at size Q),  
D(NATURAL LIGHT), L (PORTRAIT), M (LANDSCAPE), N (SPORT), O (NIGHT), H (NIGHT  
TRIPOD), Q (SUNSET), R (SNOW), S (BEACH), F (UNDERWATER), U (PARTY)  
V (TELE/WIDE), X (2-COLOR), W (2-SENSITIVITY)  
B (INTERVAL 3D SHOOTING), A (INDIVID. SHUTTER 3D)  
None  
Advanced 2D modes  
Advanced 3D modes  
Picture stabilization  
Intelligent Face Detection Available (D only)  
Shutter speed  
Continuous  
O: 1 8 s– 500 s • H: 3s 500 s • M: 1 2 s– 1,000 s • Other modes: 1 4 s– 1,000 s  
1
1
1
1
/
/
/
/
/
/
/
I (C): Up to 2fps (size Q); max. 40 frames  
J (D): Up to 3fps (size Q); max. 40 frames  
Mode: Single AF  
I (D): Up to 1fps; max. 40 frames  
Focus  
Autofocus system: Contrast-detect TTL AF  
Focus-area selection (Intelligent Face Detection off): Center (C/D), auto-area (D)  
Auto; seven manual preset modes for direct sunlight, shade, daylight fluorescent, warm white fluores-  
cent, cool white fluorescent, incandescent, and underwater lighting  
Off, 2sec., 10sec.  
Auto flash; effective range when sensitivity is set to ISO 800 is approx. 60cm–3.6m/2ft.11.8ft. (wide  
angle), 60cm–3.1m/2ft.10.2ft. (telephoto), or in macro mode (D only) 30cm–80cm/1ft.–2.6ft. (wide angle),  
60cm–1.5m/2ft.–4.9ft. (telephoto)  
White balance  
Self-timer  
Flash  
Flash modes  
Auto, fill flash, off, slow sync (red-eye removal off); auto with red-eye removal, fill flash with red-eye removal,  
off, slow sync with red-eye removal (red-eye removal on)  
104  
Specifications  
System  
Monitor  
3.5-in., 1,150k-dot C/D color lenticular LCD monitor; frame coverage approx. 100%  
Movies  
Shooting options  
j(1,280 × 720/720p, 24 fps), f(640 × 480/VGA, 30 fps), g(320 × 240/QVGA, 30 fps); stereo sound  
C: Auto parallax, power management, framing guide, and frame number memory  
D: Intelligent Face Detection with red-eye removal, power management, framing guide, and  
frame number memory  
Playback options  
Other options  
C: Parallax adjustment, micro thumbnails, multi-frame playback, sort-by-date, cropping, resize,  
and slide show  
D: Intelligent Face Detection, red-eye removal, micro thumbnails, multi-frame playback, sort-by-  
date, cropping, resize, slide show, and image rotation  
PictBridge, Exif Print, language selection (Arabic, Simplified Chinese, Traditional Chinese, Czech, Dan-  
ish, Dutch, English, Farsi, Finnish, French, German, Greek, Hebrew, Hungarian, Indonesian, Italian, Japa-  
nese, Korean, Lithuanian, Norwegian, Polish, Portuguese, Romanian, Russian, Slovak, Spanish, Swedish,  
Thai, Turkish, Ukrainian, and Vietnamese), time difference, silent mode  
Input/output terminals  
A/V OUT (audio/video output) 8-pin multi-connector for NTSC or PAL output with monaural sound  
HDMI output  
HDMI mini connector  
Digital input/output  
USB 2.0 High Speed (shares A/V OUT connector); PTP (Picture Transfer Protocol)/MTP (Media Transfer Protocol)  
105  
Specifications  
Power supply/other  
Power sources  
NP-50 rechargeable battery; AC-5VX AC power adapter and CP-50 DC coupler (sold separately)  
Battery life (approximate  
number of frames that  
can be taken with fresh or  
fully charged batteries)  
Batttteeryy tyype  
NP-50  
Approximate number of frames  
150  
CIPA standard, measured in C B mode using battery supplied with camera and SD memory card.  
Note: Number of shots that can be taken with battery varies with battery charge level and will decline  
at low temperatures.  
Camera dimensions  
(W × H × D)  
Camera weight  
Shooting weight  
Operating conditions  
124.0mm×65.9mm×27.8 (21.0*)mm/4.9in. ×2.6in. ×1.1 (0.8)in.  
* excluding projecting parts, measured at the thinnest part  
Approx. 230g/8.1oz., excluding batteries, accessories, and memory cards  
Approx. 250g/8.8oz., including batteries and memory card  
Temperature: 0°C to +40°C/+32°F to +104°F  
Humidity: 80% or less (no condensation)  
NP-50 rechargeable battery  
BC-45W battery charger  
Nominal voltage  
Nominal capacity  
Operating temperature 0°C+40°C/+32°F+104°F  
Dimensions (W × H × D) 35.4mm×40.0mm×6.6mm/  
1.4in. ×1.6in. ×0.3in.  
DC 3.6V  
1000mAh  
Rated input  
Input capacity  
Rated output  
Supported batteries  
Charging time  
100V–240V AC, 50/60Hz  
8.0VA (100V)/12VA (240V)  
4.2V DC, 550mA  
NP-50 rechargeable batteries  
Approx. 150 minutes (at 20°C/68°F)  
Weight  
Approx. 18g/0.6oz.  
Dimensions (W × H × D) 91 mm × 62 mm × 23 mm/  
3.6in. ×2.4in. ×0.9in.,  
excluding projections  
Weight  
Approx. 67g/2.4oz., excluding battery  
Operating temperature 0°C+40°C/+32°F+104°F  
Note: Weight and dimensions vary with the country or region  
of sale.  
106  
Specifications  
Notices  
• Specifications subject to change without notice. FUJIFILM shall not be held liable for damages resulting from  
errors in this manual.  
• Although the monitor is manufactured using advanced high-precision technology, small bright points and  
anomalous colors may appear, particularly in the vicinity of text. This is normal for this type of monitor and does  
not indicate a malfunction; images recorded with the camera are unaffected.  
• Digital cameras may malfunction when exposed to strong radio interference (e.g., electric fields, static electric-  
ity, or line noise).  
• Due to the type of lens used, some distortion may occur at the periphery of images. This is normal.  
107  
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN  
http://www.fujifilm.com  

ARC Audio FD5725 User Manual
Blaupunkt MONTE CARLO TCM 169 User Manual
Canon XF205 9592B002 User Manual
Casio CFX 9850GB User Manual
Ikelite Canon 6082 User Manual
JBL GTO17T User Manual
JVC 1000MKV_UN_VP User Manual
JVC Camcorder GY HM600U User Manual
JVC GR AX437 User Manual
JVC GR DVL9700 User Manual