OWNER’S
MANUAL
A802
A1004
D2205
models
LIMITED TWO-YEAR CONSUMER WARRANTY
Directed Electronics, Inc. promises to the
original purchaser, to replace this product
should it prove to be defective in workman-
ship or material under normal use, for a
period of two years from the date of
purchase by the dealer as indicated by the
date code marking of the product PROVIDED
the product was installed by an authorized
Directed dealer. During this two year period,
there will be no charge for this replacement
PROVIDED the unit is returned to Directed,
shipping pre-paid. If the unit is installed by
anyone other than an authorized Directed
dealer, the warranty period will be one-year
from the date of purchase by the dealer as
indicated by the date code marking of the
product. During this one-year period there
will be no charge for this replacement
PROVIDED the unit is returned to Directed,
shipping pre-paid. This warranty is non-trans-
ferable and does not apply to any unit that
has been modified or used in a manner
contrary to its intended purpose, and does
not cover damage to the unit caused by
installation or removal of the unit. This
warranty is void if the product has been
damaged by accident or unreasonable use,
neglect, improper service or other causes
not arising out of defects in materials or
construction. ALL WARRANTIES INCLUDING
BUT NOT LIMITED TO EXPRESS WARRANTY,
IMPLIED WARRANTY, WARRANTY OF
MERCHANTABILITY, FITNESS FOR PARTIC-
ULAR PURPOSE, AND WARRANTY OF NON-
INFRINGEMENT OF INTELLECTUAL PROPERTY
ARE EXPRESSLY EXCLUDED TO THE
MAXIMUM EXTENT ALLOWED BY LAW, AND
DIRECTED NEITHER ASSUMES NOR AUTHO-
RIZES ANY PERSON TO ASSUME FOR IT ANY
LIABILITY IN CONNECTION WITH THE SALE
OF THE PRODUCT. DIRECTED HAS
ABSOLUTELY NO LIABILITY FOR ANY AND
ALL ACTS OF THIRD PARTIES INCLUDING ITS
AUTHORIZED DEALERS OR INSTALLERS. Unit
must be returned to Directed, postage pre-
paid, with: consumer’s name, telephone
number, and address, authorized dealer’s
name and address, and product description.
IN ORDER FOR THIS WARRANTY TO BE VALID,
YOUR UNIT MUST BE SHIPPED WITH PROOF
OF INSTALLATION BY AN AUTHORIZED
DIRECTED DEALER. ALL UNITS RECEIVED BY
DIRECTED FOR WARRANTY REPAIR WITHOUT
PROOF OF DIRECTED DEALER INSTALLATION
WILL BE COVERED BY THE LIMITED ONE-YEAR
PARTS AND LABOR WARRANTY. Note: This
warranty does not cover labor costs for the
removal and reinstallation of the unit. BY
PURCHASING THIS PRODUCT, THE
CONSUMER AGREES AND CONSENTS THAT
ALL DISPUTES BETWEEN THE CONSUMER
AND Directed SHALL BE RESOLVED IN ACCOR-
DANCE WITH CALIFORNIA LAWS IN SAN
DIEGO COUNTY, CALIFORNIA.
3
© 2004 Directed Electronics, Inc
FEATURES
„ High-speed MOSFET switching
power supply and complimentary
bi-polar outputs
Bitwriter® module with Audio
programming
„ Continuously variable 12 dB/octave
„ Stereo, mono, or simultaneous
two-way crossover(s)
stereo/mono operation
„ Switchable 8 dB bass EQ function
„ Thermal, DC offset, reverse polarity,
short circuit and over/under
voltage protection
„ Remote subwoofer level control
function (A1004 and D2205 only)
„ Variable input sensitivity optimizes
„ Programmable features controlled
via ESP® serial databus and
Directed's proprietary Bitwriter®
match with different signal sources.
„ Chrome plated wire and RCA jacks
*
tool (998T)
ensure maximum signal transfer
®
*
The Bitwriter unit must have version
„ Rugged extruded two piece
1.906 or above to fully access the
amplifier features menu.
„ ESP® port for connection to ESP-2
heatsink and cover
„ Unity gain pass through RCA jacks
Security components and current
WARNING
High-powered car audio
systems may produce
sound pressure levels that
exceed the threshold at which hearing
loss may result.
They may also impair a driver’s ability to
hear traffic sounds or emergency vehi-
cles. Use common sense and practice
safe listening habits when listening to or
adjusting your audio system.
4
© 2004 Directed Electronics, Inc
NOTE
Prior to servicing your vehicle ensure
If the alarm is replaced with another
ESP2 alarm system, ensure that the
amplifier goes through a learn routine
(using the Bitwriter®) prior to re-
enabling the anti-theft feature.
disarmed
that the alarm system is
. Due
to the amplifier’s anti-theft feature (if
enabled), amplifier operation is disabled
when the main power to the amplifier is
removed while the alarm is armed. The
amplifier operation must then be reset.
INSTALLATION GUIDELINES
1. Please read this owner's manual care-
fully before installing this amplifier.
connected directly to the car at a
bare metal surface, preferably
scraped body sheet metal. Do not
use factory grounded locations,
seat bolts, or brackets that are
spotwelded.
2. Disconnect the battery ground
terminal prior to making any elec-
trical connections.
3. Check for any hazards or obstruc-
tions such as gas tanks, fuel or
brake lines, and wiring harnesses
before mounting the amplifier.
7. Always fuse your power connection
within in 8 to 10 inches of the
battery terminal. Use a fuse or
circuit breaker rated slightly more
than the on-board fuse(s) of the
amplifier(s). The gauge of power
wire used should take into account
the total current draw of the
system, and the length of the wire
used. IASCA and other auto sound
competition organizations have
charts available for this; you can
also find a chart in the MECP study
guide. Minimum wire gauge recom-
mendations for the individual ampli-
fiers are listed on the specification
4. Pick a mounting location that will
provide adequate access and venti-
lation and protect the amplifier
from heat, moisture, and dirt.
5. Avoid sharp metal areas when
routing cables to the amplifier, and
run RCA cables away from the
power cables and other potentially
noisy car harnesses.
6. The amplifier should be grounded
with a short, heavy gauge wire
5
© 2004 Directed Electronics, Inc
page. Always use the same gauge
wire for the amplifier ground that
you use for the power wire. Be sure
to examine the battery ground
cable of the vehicle, and if neces-
sary, upgrade it by adding an addi-
tional ground wire that is the same
gauge as the amplifier's power
wire. Remember, the amplifier can
only deliver its rated output when it
is not current limited by the power
and ground supply wires.
9. Battery and ground connections to
the vehicle should be made with
crimped ring terminals of the appro-
priate size (surface area is what
counts); soldering the terminals after
crimping is also recommended.
10. Due to the high-frequency MOSFET
switching power supply, filtering the
power cable is not generally
required (remember that the amp
can't deliver full output if the power
supply is restricted). Proper
grounding of the signal source is
mandatory for the amplifier to
reach its performance peak. If the
RCA inputs are not grounded
adequately via the signal source,
electrical noise from the vehicle
may be picked up in the system.
8. This amplifier is designed to drive a
speaker load that measures from 2
to 8 ohms (1 ohm on D2205 Sub
Output). Keep in mind that heat is
the long-term enemy of automotive
electronics and the lower your
speaker load, the more heat is
generated. For low impedance
speaker applications or restricted
ventilation installations, an external
cooling fan may be advisable.
FRONT PANEL CONNECTIONS/STATUS LED
ESP® Port -
1.
2.
connection port for
processors at voltages between
250 mV and 7.5 volts. (A1004
and D2205 also have a Rear
Input.)
Bitwriter® or ESP2 security system.
ESP® Status LED -
®
indicates ESP
functionality and is used to diag-
nose ESP® features.
4.
- these pass
RCA Output Jacks
through RCA jacks can be used to
send a signal to a second amplifier.
RCA Input Jacks
outputs from head units or signal
3.
- accepts line level
6
© 2004 Directed Electronics, Inc
Line Out Switch (D2205) -
positions:
Remote -
optional accessory which
5.
three
10.
11.
allows the level to be adjusted
remotely (usually located for
control by the vehicle’s driver).
sum L/R
—left front and rear and
right front and rear channels are
summed.
Subsonic -
the OFF position takes
sub L+R
—set the switch to this
the filter out of the system, the IN
position places the the filter into the
system (D2205).
position when using an additional
D1200 amplifier connected in
Parallel mode.
Sub Gain -
adjustment.
12.
13.
subwoofer channel gain
sub 180°
—set the switch to this
position when using an additional
D1200 amplifier connected in
External Bridge mode.
Status LED
- Will illuminate GREEN
to indicate the amplifier is on and
operating normally, and will be illu-
minated RED if the amplifier shuts
down due to short circuit, DC offset,
or overheating detected by on-
board protection circuitry.
Gain -
6.
controls amplifier sensitivity
and is used to match the input level
of the amplifier to the output level
of the signal source. (front and rear
on A1004 and D2205.)
LED/Fan -
14.
allows connection of an
optional
Bass EQ -
bass boost (A802 and A1004).
7.
8.
allows 8dB additional
optional
LED light bar or
cooling fan for the amplifier.
X-Over HPF, Flat, LPF -
the HPF
LPF -
15.
16.
sets high frequency limit of
attenuates low frequencies and is
used with mid-range speakers and
tweeters. Full does not attenuate
any frequencies and is for full range
speaker systems. LPF attenuates
high frequencies and is used for
subwoofers.
subwoofer channel (D2205).
Bass EQ -
base boost on sub channel
(D2205).
allows 8dB additional
Sub Input/Line Out -
jacks (4) (Sub/Line Out) as either
Subwoofer Input or Line Output.
17.
selects RCA
X-Over Freq -
9.
adjusts the crossover
point (50-500Hz) for the on-board
active crossover.
7
© 2004 Directed Electronics, Inc
FIGURE 1—AMPLIFIER CONNECTIONS — FRONT
1
3
4
6
8
9
7
14
13
A802
2
1
3
4
17
6
8
9
7
10 14
13
A1004
2
2
3
4
5
6
7
8
9
10 11 12
13
D2205
1
17
16 15 14
FIGURE 5—LED/FAN HARNESS
BLACK
BLUE
-
TO LEDs
TO FAN
+
-
BLACK
RED
+
8
© 2004 Directed Electronics, Inc
REAR PANEL CONNECTIONS
Fuses -
Ground -
Connect this terminal
1.
These fuses protect the
2.
amplifier against internal electrical
damage and are meant to protect
the amplifier only. All other power
connections should be fused at the
source.
directly to the sheet metal chassis
of the vehicle, using the shortest
wire necessary to make this
connection. Always use wire of the
same gauge or larger than the (+)
12 volt power wire. The chassis
connection point should be scraped
free of paint and dirt. Use only
quality crimped and/or soldered
connectors at both ends of this
wire. DO NOT connect this terminal
directly to the vehicle battery
ground terminal or any other
factory ground points.
The A802 uses 2-30A fuse, the
A1004 uses 2-40A fuses, and the
D2205 uses 3-40A fuses.
(+) 12 Volt Power
2.
- Connect this
terminal through a FUSE or CIRCUIT
BREAKER to the positive terminal of
the vehicle battery or the positive
terminal of an isolated audio
system battery.
Speaker Terminals
3.
-
Connect
subwoofers to these terminals.
(Refer to the Speaker Wiring
Diagrams section of this guide.)
WARNING: Always protect this power wire by installing a fuse
or circuit breaker of the appropriate size within
12 inches of the battery terminal connection.
Remote Turn On
2.
- This terminal turns
on the amplifier when (+) 12 volt is
applied to it. Connect it to the remote
turn on lead of the head unit or signal
source.
9
© 2004 Directed Electronics, Inc
FIGURE 2—AMPLIFIER CONNECTIONS REAR
1
2
3
A802
A1004
D2205
®
ESP FEATURES AND CONTROLS
*
These amplifiers incorporate an on-board
Directed ESP® Engine. In addition to
allowing menu-driven parameter adjust-
ment*, operate with security products
from Directed Electronics to incorporate
advanced ESP2 features. Your dealer
can use a Bitwriter® with Firmware
version 1.906 or later to access these
parameters.
The ESP® features are
Note:
obtained by using Bitwriter® and a
3 pin ESP® cable. While a
Bitwriter® can only talk to one
ESP®/ESP2 device at a time,
multiple amplifiers can be set to
respond to Arm/Disarm commands.
Simply repeat the TX ID Learn
procedure for each amplifier. When
10
© 2004 Directed Electronics, Inc
completed use a Y-cable to connect
the Alarm signals to both ampli-
fiers.
LED tubes. In the OFF mode the
external FAN port is disabled.
Service Code Display -
3.
The Directed
Prior to using the anti-theft or
ESP® Engine stores up to seven
previous faults for later replay. The
Service Code Display allows the
installer to step through the fault
history.
Note:
valet features it is recommended
that the alarm be installed and its
functionality verified. Please consult
the install or operations guide for
the appropriate alarm.
- OFF -
In the OFF position, the
amplifier operates normally.
For the Bitwriter® to Amp connection,
the cable must have the same color
sequence at both ends of the cable. For
the Alarm to Amplifier, the Transmit and
Receive wires must cross from one end
to the other.
- FLASH CODE ON LED -
the last
recorded fault is "replayed" on the
ESP® Indicator LED. If the unit has
never recorded a fault, the ESP®
Status indicator will not flash.
Bitwriter® commands can control para-
meters such as Turn on Delay, Fan
Control, Input Gain adjustment, and also
place the amplifier into a monitoring
state for commands from an ESP2
equipped alarm.
- RESERVED -
for future use.
no function, reserved
- CLEAR LAST FAULT -
Clears the last
fault. Note that this allows you to
see previous faults prior by back-
stepping one at a time through the
fault history.
Turn-On Delay -
1.
0.75, 1.00, 1.25,
1.75, 2.25, 2.75, or 3.25
seconds. 1.75 seconds is the
factory default setting.
Input Gain Range -
4.
5.
The sensitivity
on the gain control can be limited
to specific ranges. The DEFAULT
position allows adjustment over the
full range of amplifier sensitivities.
There are 4 other ranges 0.5-1.0V,
1.0V-2.0V, 2.0-4.0V, 4.0-8.0V.
Fan Control - AUTO -
2.
The fan will
automatically turn on when the
internal temperature exceeds
approximately 40 deg C. The ON
option causes the fan to operate
whenever the Amplifier is on. Use
the ON option if you are using the
external FAN port to drive optional
Input Gain Adjustment -
In the LOCK
position, the gain range and gain
control can be locked out to prevent
accidental mis-adjustment. The
11
© 2004 Directed Electronics, Inc
Default mode is UNLOCKED.
Valet -
into a "stolen state". The ESP®
Status indicator will blink rapidly,
and the amplifier will not continue
its power up sequence. Also when
there is currently an ARM signal
active on the bus, the amplifier
cannot be written to by the
Bitwriter®.
6.
Selecting ENABLE allows the
amplifier to monitor valet signals
from the alarm system. The ampli-
fier will not power up once remote
power is removed when the Valet
monitoring mode is ENABLED and
the alarm system has been set into
Valet mode.
To reactivate the amplifier, connect
the alarm that was used to arm the
amplifier, and press the disarm
button. Ensure the remote line is
off(turn it off if this is not the
case), and then turn the amplifier
on. The amplifier should power up
normally after the Turn On Delay
expires.
Note:
To make use of the Anti-theft
or Valet features, the amplifier must
"learn" which transmitters are asso-
ciated with the currently used alarm
system. See item 8 below.
If selected while the remote power
is on, the amplifier will continue
playing until the remote power is
turned off.
Learn TX IDs
8.
Default Off.
Before the unit will
To Clear Valet Mode, Disable Valet
mode on the alarm, then cycle the
remote power line off then on
again. The amplifier will power up
normally after the Turn On Delay
time has expired.
respond to Arm/Disarm/Valet
Commands from the alarm system,
it needs to establish communica-
tions with this alarm system. Once
this procedure is performed, the
unit will store this information
permanently in memory. The proce-
dure only needs to be repeated if
the alarm unit is replaced or all the
transmitters in an alarm system are
replaced.
Anti-theft -
7.
Selecting ON, allows the
amplifier to monitor Arm and
Disarm signals from the alarm,
rendering the amp in-operable if
stolen. When OFF, these signals are
ignored. OFF is the factory default
setting.
To perform a transmitter "learn":
1. Connect Bitwriter® to amplifier.
Press READ on the Bitwriter®.
When main power is removed while
the unit is armed, the unit is placed
12
© 2004 Directed Electronics, Inc
2. Press the up arrow 3 times, or the
down arrow 7 times to reach the
Learn TX IDs menu. Press 'Select'
until the ON appears.
to indicate Arm or Disarm
commands. This allows the installer
to verify that the proper cable is in
use and that the transmitters have
been properly programmed. The
unit must still be programmed to
respond to Valet and Arm
commands with a Bitwriter® for the
Anti-theft/Valet modes to lock out
unauthorized operation.
3. Press the write key twice. The ESP®
status indicator should begin
blinking.
Note:
The following should be
accomplished within 20 seconds or
the learn session will time out. If
this occurs, the LED will stop
blinking. Reconnect the Bitwriter®
and press WRITE twice to re-enter
the TX ID Learn mode.
Major Version Number:
8.
9.
This number
will allow verification of the
firmware installed in the amplifier.
This will be useful information
should your amplifier ever need
service.
4. Disconnect the Bitwriter® and
connect the Amp to the alarm
cable.
Minor Version Number:
This number
references the minor version of your
amplifier firmware.
5. Press ARM on any transmitter
attached to the alarm system. The
LED should go on if the amplifier
was on prior to TX ID or go out if
the amplifier is off.
ESP® Status Indicator:
The ESP® Status indicator flashes to
indicate the current operational
mode. This can be used in conjunc-
tion with the Power LED to help
determine the source of the
problem.
Note:
When the amplifier receives
ESP® bus activity(typically either
arm or disarm signals, it will blink
13
© 2004 Directed Electronics, Inc
Power/Protection LED
ESP® Status Indicator
Solid Red
Mode
Normal Operation
Turn On delay or TX learn
Thermal shutdown
Overcurrent
Green
Green
Red
Red
Red
Red
Off
Flashing
Flashing Slowly
Flashing Rapidly
Slow Flash (50% duty cycle) Overvoltage
Slow Flash (mostly off)
Off
Under-voltage
Amplifier Off
Off
Flashing
Arm/Valet received
Amplifier in Anti-theft/Valet
Amplifier armed
Off
Flashing Rapidly
Flashing
On
®
Note
: Remember that the Directed ESP Engine incorporates a digital gain control with
a finite number of adjustment steps (32). A very small adjustment may not cause
any audible changes in output. In addition the range selected may further restrict the
adjustment. Extremely quick, large changes may result in audible artifacts, particu-
larly on low frequency material as the gain is changing more rapidly than the source
electrical wave.
14
© 2004 Directed Electronics, Inc
SPEAKER WIRING DIAGRAMS A802/A1004
Stereo operation (top view)
L CH
R CH
Bridged operation (top view)
L CH
B
R
I
D
G
E
R CH
D
Note:
The A1004 amplifier connections are the same as shown above, except that
there are outputs for Front and Rear speakers.
15
© 2004 Directed Electronics, Inc
SPEAKER WIRING DIAGRAMS D2205
Front/Rear operation (top view)
CH 1 FRONT
CH 2 FRONT
CH 3 REAR
CH 4 REAR
16
© 2004 Directed Electronics, Inc
Front/Rear Bridged operation (top view)
B
R
I
D
G
E
CH 1
CH 2
FRONT
D
B
R
I
D
G
E
CH 3
CH 4
REAR
D
17
© 2004 Directed Electronics, Inc
Subwoofer operation (top view)
B
R
I
D
G
E
CH 1
CH 2
D
SUB +
SUBWOOFER
B
R
I
D
G
E
CH 3
CH 4
D
SUB -
18
© 2004 Directed Electronics, Inc
CROSSOVER SETTINGS AND GAIN ADJUSTMENT
Your Directed Audio power amplifier needs to
be adjusted carefully to achieve maximum
performance. These are some guidelines to
follow when fine-tuning the amplifier.
„ For full-range and simultaneous
stereo/mono bass applications, the
crossover selection switch should be
set to FULL. If the amplifier is driving
your subwoofers, set the switch to
LOW, and for mid-bass/midrange
output, set to HIGH.
„ The crossover frequency control needs
to be adjusted to suit your particular
system. For subwoofer applications,
try and keep the setting low enough to
prevent image smearing (you should
not be able to hear male voices from
the subwoofer) but not so low as to
create a gap between the subwoofer
and the mid-bass/midrange speakers.
For mid-bass/midrange settings, try to
keep the setting low enough to keep
your sound stage in front of you,
without overdriving the speaker. It will
be to your advantage to spend some
extra time with this adjustment,
listening to familiar music or system
set-up discs to achieve the kind of
musical reproduction that you prefer.
„ The gain adjustment allows you to set
proper signal match for clean, quiet
amplifier operation. For full-range and
simultaneous stereo/mono bass appli-
cations, start by playing some music
you are familiar with. With the gain
adjustment on the amplifier in the
middle of its rotation, bring up the
volume on your head unit to the 3/4
volume setting or until you start to
hear distortion or clipping. If you hear
distortion before you reach the 3/4
volume setting of your head unit,
reduce the gain setting on the ampli-
fier and start to raise the head unit
volume again. When you can listen to
the music at or slightly above 3/4 on
your head unit without audible distor-
tion, slowly raise the gain of the ampli-
fier until distortion is heard, then back
off the gain until the distortion is not
audible. This setting will allow you to
reach full output with all but the
quietest of source material, while
avoiding excessive noise in the
system.
Note:Remember that the Directed ESP® amplifiers use a digital
gain control with a finite number of adjustment steps. A very
small adjustment may not cause any audible change in level.
„ The same procedure should be used for
adjusting the amplifier when the on
board crossover is set to LOW or HIGH,
but you will also have to take into
consideration the effect that gain
adjustment has on system frequency
response and imaging. Again, plan on
spending some time with music that
you know getting the gain and
crossover settings the way you like.
Test discs and analyzers may help with
this process, but in the end it's your
ears that count - listen to the music!
19
© 2004 Directed Electronics, Inc
LED TUBE INSTALLATION (OPTIONAL)
This Directed Audio amplifier has been designed with a custom heat sink that can
accommodate two (optional—not supplied) VARAD LED tubes.
1. Before installing the LED tubes, remove and discard the mounting feet from the
VARAD LED tubes.
2. Slide each LED tube assembly into your Directed Audio amplifier heat sink. Ensure
that the LEDs are facing out for optimal visibility. The wires from the LED tube
assembly should be on the signal input end of the amplifier. The Black wire from
the LED tube is ground and the Black/White wire from the LED tube is power.
4. Run the two wires from the tube assembly and connect them to the 4-pin
LED/FAN input connector. Refer to the LED/FAN harness diagram given earlier in
this manual.
NOTE:
If the optional fan IS NOT being used, it is recommended that the second LED tube be wired to this circuit. If the optional
fan is being used, it is recommended that the second LED tube be wired in parallel with the first LED tube.
Use the following cross reference chart to select the proper length VARAD LED tube for
use with your Directed Audio amplifier.
Directed Amplifier—VARAD Cross Reference Chart
Directed Part Number
Directed Model
VARAD Model
HLX6, HL6, HLW9
HLX6, HL6, HLW9
HLX6, HL6, HLW9
HLX12, HL12, HLW15
HLX6, HL6, HLW9
HLX6, HL6, HLW9
HLX6, HL6
QTY Required
45120
45125
45150
45155
45095
45100
45105
45110
A502
A802
A404
A1004
D600
2
2
2
2
2
2
2
D800
D1200
D2400
D2205
HLX12, HL12
2
45165
(2) HLX12, (2) HL12
2 or 4
20
© 2004 Directed Electronics, Inc
SUBSONIC FILTER ADJUSTMENT (D2205 ONLY)
This amplifier incorporates a subsonic filter
to maximize the performance of a
subwoofer. The subsonic filter is a high pass
filter that removes unwanted bass output
at very low frequencies from the woofer.
This increases the output of a subwoofer by
as much as 3 dB by increasing the mechan-
ical power handling of the subwoofer.
Depending on the type of enclosure the
subsonic filter can increase the useable low
frequency output by an additional 10 dB!
Acceptable boost levels are determined by
the type of enclosure used, wattage of the
amplifier, and the woofer’s excursion capa-
bility.
The following guidelines should be used
for proper set-up of the subsonic filter to
provide optimum performance and relia-
bility from your system.
CEA SPECIFICATIONS
A802
Power Output: 150 Watts RMS X 2 Channels at 4 Ohms and < 1% THD+N
Signal to Noise Ratio: 76 dBA (reference 1 Watt into 4 Ohms)
Additional Power: 200 Watts RMS X 2 Channels at 2 Ohms < 1% THD+N
A1004
Power Output: 90 Watts RMS X 4 Channels at 4 Ohms and < 1% THD+N
Signal to Noise Ratio: 81 dBA (reference 1 Watt into 4 Ohms)
Additional Power: 125 Watts RMS X 4 Channels at 2 Ohms < 1% THD+N
D2205
Power Output: 80 Watts RMS X 4 Channels at 4 Ohms and < 1% THD+N
280W RMS X 1 Channel at 4 Ohms < 1% THD+N
Signal to Noise Ratio: 80 dBA (reference 1 Watt into 4 Ohms)
Additional Power: 125 Watts RMS X 4 Channels at 2 Ohms < 1% THD+N
Additional Power Subchannel: 600 Watts RMS X 1 Channel at 1 Ohm < 1% THD+N
21
© 2004 Directed Electronics, Inc
SPECIFICATIONS
A802, A1004, and D2205
>66% @ 4 ohms
Conversion Efficiency
Frequency Response
Signal-to-Noise Ratio
Separation
20-20,000 Hz
>98 dBA
65 dB @ 1 kHz
Damping Factor
>150, >50 (D2205 sub-channel)
2-way Butterworth/50 to 500 Hz
12 dB/octave
Crossover Type/Range
Crossover Slope
Bass Equalization
Subsonic Filter
0 to +8 dB
Variable
RCA Input/Output Jacks
Input Impedance
Input Sensitivity
2-channel in/2-channel paralleled full-range out
20K ohms
Variable from 250 mV to 8 volts
10 to 16 VDC
Supply Voltage
30Ax2 (A802)
40Ax2 (A1004)
40Ax3 (D2205)
Fusing
Minimum Cable Requirements
(AWG)
#8
varies
Dimensions
Port Output (Optional
Fan)/LED (Optional)
12V @<200mA
22
© 2004 Directed Electronics, Inc
The company behind this system is Directed Electronics, Inc. Since
its inception, Directed has had one purpose, to provide customers with the finest
vehicle security, car stereo products, rear seat entertainment, and accessories avail-
able. The recipient of more than 20 patents in the field of advanced electronic tech-
nology, Directed is ISO 9001 registered.
Directed Electronics, Inc.
Vista, California 92081
Directed® is committed to delivering world-class quality
products and services that excite and delight our customers.
Quality Directed products are sold and serviced throughout North America and around the world
Call 800 274 0200 for more information about our products and services
© 2004 Directed Electronics, Inc.
-
All rights reserved
-
G45125.55.65 12-04
|