Cardo Scala Rider MultiSet Q2 Q2 User Manual

Gebrauchsanleitung

Guide d’Utilisation

Guida di Avvio

Guia de Usario

User Guide

™

MultiSet

SCALA RIDER^®Q2^™MultiSet |

CONTENTS OF RETAIL BOX

Two Headsets

INTRODUCTION

Congratulations and thank you for choosing the SCALA RIDER Q2

MultiSet Bluetooth® Headset package for bikers.

Volume

This User Guide will help you operate the headset, but you should

ﬁrst familiarize yourself with the Bluetooth functionality of your cel-

lular phone and/or GPS device before using the SCALA RIDER Q2.

Charging

Jack

This retail box contains two SCALA RIDER Q2 headsets that already fac-

tory paired (see details below). In wide open terrain two bikers can com-

municate via intercom (in full duplex*) at a range of up to 500 m / 1,640 ft.

Typical eﬀective range is approximately 250 m / 800 ft. Please note that

the actual range can vary widely as a result of many reasons (e.g. terrain,

obstacles, weather conditions etc.)

Volume

Down

CTRL – Control Button

• Power On, Power Oﬀ

• Answer/End

MC – Multi-Connection

• Radio On/Oﬀ/change stations

• Initiate/Terminate Buddy

Intercom call with Primary or

Secondary Buddy

The SCALA RIDER Q2 is multi-talented and (in addition to its connec-

tion to the second Q2 unit) it can also serve as a stand-alone unit for

the following connectivity modes:

Left Speaker

(short cord)

• As a Bluetooth headset for mobile phone communication**

Two Helmet Clamps

• As a Biker-to-Passenger Intercom device that connects with any

SCALA RIDER headset worn by the passenger

Right Speaker

(long cord)

• As a speaker that transmits GPS Navigation instructions from a

compatible GPS device***

Microphone

• As a speaker that transmits audio from the embedded FM Radio

• As a speaker that transmits music from your MP3 player

Back

Plate

Tab

NOTE: Each Q2 headset can establish an audio connection with one

Bluetooth device at a time. Read the section “Using the Headset” on

how to switch the audio connection between the paired devices.

____________________

Sliding Plate

MP3 Jack

* Full duplex calls allow you to speak and hear the other party speak simultaneously

NOTE: The use of

** Mobile phones that do not support the Bluetooth Handsfree proﬁle may prevent you

from using the Redial and Call Reject features. The Q2 supports headset and handsfree

proﬁles at up to 10 m / 30 ft. distance from the mobile phone

two speakers may be

illegal in certain jurisdictions. Please

check the local regulations and act

accordingly.

*** Requires Bluetooth compatibility on the part of the GPS device

ꢁ

| SCALA RIDER^®Q2^™MultiSet

SET UP AND CONFIGURATION

2 Wall Chargers

Rider-to-

2 Allen Wrenches

Passenger

Full Duplex

Intercom

Embedded

FM Radio

2 sets of Velcro Pads

Bike-to-Bike

Intercom up to

500 meters

(1,640 ft.)

2 MP3 Cables

2 Glue Plates

Connection

2 Pre-moistened Towelettes

2 Carry-Pouches

SCALA RIDER Q2

or SCALA RIDER

Family Headset

4 Microphone Sponges

Flat sponge for full-face helmets and round sponge for other helmet types

Mobile Phone

User Guide, including Warranty and Registration form

GPS

IMPORTANT:

Your headsets are water-resistant, designed for use under moderate rain

or snow conditions. However, the headsets are not waterproof and

should not be used under severe weather conditions.

The cover tongue protecting the Charging Jack should be kept tightly

closed at all times to prevent moisture from entering the device.

STEP 1

NOTE: WHILE MOST INSTRUCTIONS IN THIS MANUAL REFER TO THE HEADSET IN THE

SET UP FOR BIKE-TO-BIKE INTERCOM: PAIRING

SINGULAR, THEY APPLY TO BOTH UNITS UNLESS INDICATED OTHERWISE.

Pairing is a one time process that is required for mutual recognition be-

tween a headset and other Bluetooth devices. Once the two headsets

are paired, they will remain paired and automatically recognize each

other whenever they are within range. The two headsets in your retail

box are already factory paired and relate to each other as the Primary

Buddy connection. In addition, each unit can be paired with an addi-

tional SCALA RIDER headset for Intercom communication. Please note

that you can speak via Intercom to one Buddy headset at a time.

BEFORE USING (CHARGING THE

HEADSET)

Make sure that the headset is fully charged for at least ﬁve hours

before initial use.

1. Connect the wall charger to the headset’s Charging Jack (located

between the two Volume Buttons).

2. While charging, the Red Light turns on (it may take up to 15

seconds until the Red Light turns on). When charging is complete,

the Red Light will turn oﬀ.

NOTE: This Manual refers to the Intercom users and other parties as:

Primary Buddy and Secondary Buddy.

ꢂ

SCALA RIDER^®Q2^™MultiSet |

PRIMARY BUDDY PAIRING (requires two SCALA

RIDER Q2 headsets)

STEP 2 (Optional)

SET UP FOR RIDER-TO-PASSENGER INTERCOM: PAIRING

There are two ways that the SCALA RIDER Q2 can be used for Rider-

to-Passenger communication.

1. If either headset is turned OFF, turn it ON by pressing and holding

the CTRL Button until the Blue Light ﬂashes three times.

2. Make sure that both headsets are now ﬂashing slowly in Blue.

A. Both Rider and Passenger are using SCALA RIDER Q2 headsets

(like the two units in your retail package).

3. Pick up one headset and simultaneously press and hold the CTRL

Button and MC Button for at least six seconds until the Red Light

begins ﬂashing rapidly, indicating it is in Intercom Pairing mode.

To Pair the two headsets, follow the Steps listed in the section

above titled PRIMARY BUDDY PAIRING.

B. The Rider is using a SCALA RIDER Q2 and the Passenger is using

a SCALA RIDER headset (i.e. a SCALA RIDER Solo, a SCALA

RIDER FM or a SCALA RIDER TeamSet Driver unit headset).

4. Repeat Step 3 again for the second SCALA RIDER Q2 headset.

Both headsets should now be ﬂashing rapidly in Red.

5. Within a few seconds, both headsets will show a solid Red

light for two seconds, and then begin flashing slowly in Blue.

To Pair the two headsets:

1. Starting with the SCALA RIDER headset turned OFF, press and hold

the CTRL button until the Red/Blue lights begin rapidly alternating.

SECONDARY BUDDY PAIRING (requires three

SCALA RIDER Q2 headsets)

In addition to the Primary Buddy pairing between the two units

in your retail box you can pair your headset with the Secondary

Buddy headset by repeating the above pairing procedure.

2. Starting with the SCALA RIDER Q2 turned ON, simultaneously

press and hold the CTRL Button and MC Button for six

seconds until the Red light begins ﬂashing rapidly, indicating it

is in Intercom Pairing mode.

3. Within a few seconds, the SCALA RIDER Q2 will show a solid Red

light for two seconds, and then begin ﬂashing slowly in Blue.

NOTE: If the Pairing process is not completed within one minute the

NOTE: Your headset can communicate with either the Primary

Buddy or the Secondary Buddy. However, neither

the Primary Buddy nor the Secondary Buddy can

communicate among each other directly via Intercom.

headset will return to Standby mode.

NOTE: When using a SCALA RIDER headset as a Passenger headset,

Voice Connect Intercom can be initiated only by the SCALA

RIDER Q2 headset. Manual Connect Intercom can be initi-

ated from either headset by pressing the MC button for SCALA

RIDER Q2 and CTRL button for other SCALA RIDER headsets.

NOTE: If the Pairing process is not completed within one

minute the headset will return to Standby mode.

RESET INTERCOM PAIRING

You can delete all of the headset’s Intercom pairings at any time.

ꢃ

| SCALA RIDER^®Q2^™MultiSet

1. Place the SCALA RIDER Q2 into Intercom Pairing mode following

the instructions in the PRIMARY BUDDY PAIRING section above.

phone’s instructions. Please consult your phone’s User Manual

for more information.

4. After a few seconds the phone will list the SCALA RIDER

Q2 as a discovered device. Select it and follow your phone’s

instructions to accept the pairing.

2. Once the Red Light begins ﬂashing rapidly, press and hold Volume

up for three seconds.

3. The Red and Blue Lights will ﬂash ﬁve times, conﬁrming that the

Reset Pairing was successful.

5. When prompted enter 0000 (four zeros) as your PIN or passkey.

6. Your phone will conﬁrm that pairing has succeeded and the

headset will begin ﬂashing slowly in Blue.

STEP 3

NOTE: If the Pairing process is not completed within two minutes the

headset will return to Standby mode.

SET UP FOR MOBILE PHONE CALLS: PAIRING

If you have a Bluetooth enabled mobile phone and would like to

make and receive phone calls using the SCALA RIDER Q2, you must

ﬁrst pair your headset to the mobile phone.

With some mobile phones, you may need to tap the CTRL button

to connect the headset to the phone after pairing is complete. The

SCALA RIDER Q2 headset will automatically connect to the last

phone connected to the headset.

NOTE: If you have a compatible Bluetooth GPS device you wish to

use with the SCALA RIDER Q2, please skip this step, and continue

ahead to STEP 4: SET UP FOR BLUETOOTH GPS DEVICE.

STEP 4

SET UP FOR BLUETOOTH GPS DEVICE: PAIRING

Pairing is a one time process. Once the headset is paired to a

specific mobile phone during this Setup Procedure, they will

remain paired and automatically recognize each other whenever

they are within range. If the connection between the phone and

headset is lost, tap the CTRL button to reconnect the devices.

If you have a Bluetooth enabled GPS device and would like to transmit

navigation instructions and sounds from the GPS device through the

headset’s speakers, you must ﬁrst pair your headset to the GPS device.

NOTE: Not all Bluetooth enabled GPS devices allow connections to

Bluetooth headsets like the SCALA RIDER Q2. Please consult your

GPS device’s User Manual for more information.

TO PAIR THE SCALA RIDER Q2 TO A BLUETOOTH

MOBILE PHONE

TO PAIR THE SCALA RIDER Q2 TO A BLUETOOTH GPS

DEVICE:

1. Turn on your phone and make sure its Bluetooth function is

activated.

2. With the SCALA RIDER Q2 headset turned ON, press and hold

the CTRL Button for at least six seconds until the Red and Blue

Lights begin rapidly alternating.

1. Turn on your GPS device.

2. With the SCALA RIDER Q2 headset turned ON, press and hold

the CTRL Button for at least six seconds until the Red and Blue

Lights begin rapidly alternating.

3. Search for Bluetooth devices on your phone by following the

ꢄ

SCALA RIDER^®Q2^™MultiSet |

3. Search for Bluetooth headsets on your GPS device by following

the device’s instructions. Please consult your GPS device’s User

Manual for more information.

and then tighten the screws.

You may need to reposition

the Clamp repeatedly until

you identify the best spot. The

microphone must be positioned

vertically and not horizontally.

4. If your GPS device prompts for a PIN or Passkey enter 0000 (four zeros).

CORRECT

INCORRECT

5. Your GPS device will conﬁrm that pairing has succeeded. The

headset will begin ﬂashing slowly in Blue.

Glue Plate Method

6. If you wish to use a Bluetooth mobile phone to make and

receive calls through the headset, you must now pair your

mobile phone to your GPS device by following your GPS

and/or mobile phone’s instructions.

You have the option to glue the Helmet Clamp onto your helmet,

when the above standard method cannot be used, or in case you

prefer to secure the Helmet Clamp with adhesive glue. This option

has been successfully used for a range of high end helmets.

NOTE: If the Pairing process is not completed within two

minutes the headset will return to Standby mode.

NOTE: While we have no reason to believe that the gluing op-

tion might negatively aﬀect any helmet, Cardo does not

assume any responsibility to that aﬀect, irrespective of

its nature and circumstances. The Glue Plate is oﬀered

as a free option that you may choose to use at your own

risk and subject to renouncement of any future claims.

ATTACHING THE CLAMP ON THE HELMET

The Helmet Clamp must be attached to the left side of the helmet.

Once attached, the headset unit can be mounted or released from

the Helmet Clamp at any time. There are two methods that can be

used in order to attach the Clamp onto the helmet:

Caution: This process can be done only once!

1. Use the enclosed Allen Wrench to remove both Allen

screws and release the Helmet Clamp’s back plate.

Standard Method: Recommended for most helmet types.

Glue Plate Method: Recommended for helmets

to which the standard method cannot be applied,

using the Glue Plate included in the box.

2. Determine the location on the helmet where the

Helmet Clamp must be attached.

Standard Method

3. Adjust the Helmet Clamp’s location on

the Helmet so that the microphone

is located opposite the center of your

mouth. You may need to reposition

the Clamp repeatedly until you identify

the best spot. The microphone must be

1. Use the enclosed Allen Wrench to loosen

the two screws on the Back Plate.

Allen

Wrench

2. Slide the Back Plate between the internal

padding and the external shell of the

Back

Plate

CORRECT

INCORRECT

helmet.

positioned vertically and not horizontally (Be sure to clean the selected

area prior to the gluing process as described in # 4 below).

3. Adjust the Clamp’s location so that the

microphone is located opposite the center of your mouth,

ꢅ

| SCALA RIDER^®Q2^™MultiSet

4. Use the pre-moistened Towelette to clean the helmet

area where you want to install the Glue Plate. Allow to dry

thoroughly.

side, near speaker [A]. Then place the

speaker [B] underneath the padding.

Speaker B

5. Peel the foil cover from the Glue Plates’ adhesive pad.

6. Place the Glue Plate into position according to #3. Press ﬁrmly 15

seconds on all 3 parts of the Glue Plate.

Speaker A

7. The adhesive pad bonds to full strength over the next 24 hours.

Therefore it is recommended to not use the headset during this 24

hour period.

ATTACHING AND REMOVING THE

HEADSET FROM THE HELMET CLAMP

8. Fasten the Clamp to the Glue Plate using the Allen screws that were

previously removed.

ATTACHING:

Slide the headset downwards along

the sliding panel until a clicking

sound indicates that the headset is

locked in place.

POSITIONING THE SPEAKERS

Attach the speakers to the Velcro

REMOVING:

inside your helmet opposite your ears

(short speaker cord for the left ear [A]

and the long speaker cord [B] for the

Press here to remove

Speaker A

Your headset can be removed for

charging and storage by pressing

your finger gently against the tab

and sliding the headset up with the

other hand.

Speaker B

right ear). You may want to use the

supplied Velcro pad.

Using two speakers inside the helmet may be prohibited in

certain jurisdictions. If this is the

case, you should tuck away the

We recommend that you remove the

headset from the helmet when not in use.

Cable

Speaker B

long corded speaker underneath

the helmet padding as follows:

Lead the speaker [B] alongside the

rim of the padding to the right

side and then back to the left

ꢆ

SCALA RIDER^®Q2^™MultiSet |

USING THE HEADSET

GENERAL USAGE

USING THE INTERCOM

Making Intercom calls

GENERAL FUNCTIONS

To start a Buddy Intercom call with the Primary Buddy while

the headset is on Standby you can either:

DESIRED RESULT:

REQUIRED ACTION:

Turn on the

headset

Turn oﬀ the

headset

Increase the

volume

Decrease the

volume

Press the CTRL Button steadily for at least three

seconds

VOICE CONNECT:

Start talking

MC BUTTON CONNECT:

Single tap the MC Button

Press the CTRL Button steadily for at least three

seconds

A Buddy Intercom call will be

established and stay on until

both sides are quiet for 30

seconds.

A Buddy Intercom call will

be established. To end the

Buddy Intercom call, single

tap the MC Button again.

Short press the Volume Up Button

Short press the Volume Down Button

To start a Buddy Intercom call with the Secondary Buddy

while the headset is on Standby:

AGC (Automatic Gain Control): In addition to manual Volume Control,

the SCALA RIDER Q2 will automatically increase and reduce its

volume according to ambient noise and driving speed.

MC Button

MC BUTTON CONNECT:

Double tap the MC Button

AUDIO SOURCES AND PRIORITIES

A Buddy Intercom call will be established. To end the

Buddy Intercom call, double tap the MC Button again.

The diﬀerent Audio Sources that are connected to the SCALA RIDER

Q2 are prioritized as follows:

Highest 1. Mobile phone Audio / GPS device (Incoming/outgoing calls ,

NOTE: When using a SCALA RIDER Headset (not a Q2 version) as a

Passenger headset, Voice Connect Intercom can be initiated only by the

SCALA RIDER Q2 headset. Manual Connect Intercom can be initiated

from either headset.

GPS audio and navigation instructions)

2. Primary Buddy Audio and Secondary Buddy Audio

3. FM Radio

Failed Connection: On the SCALA RIDER Q2, if you attempt to start

a Buddy Intercom call with a Buddy that is already on a Phone/GPS/

Intercom call, you will hear a double beep indicating the Buddy is busy.

Lowest 4. MP3 Connectivity

A high priority Audio Source will always interrupt any lower priority

Audio Source.

Reconnecting the Intercom: If the SCALA RIDER Q2 and its

Intercom Buddy headset go out of range and disconnect from each

other, the SCALA RIDER Q2 will automatically try to reconnect to its

Intercom Buddy for ﬁve minutes.

i.e.

Mobile phone call interrupts Intercom call

Intercom call interrupts FM Radio

ꢇ

| SCALA RIDER^®Q2^™MultiSet

You can manually reconnect at any time by pressing the MC Button

Enable/Disable Voice Connect feature

(single tap for Primary Buddy and double tap for Secondary Buddy).

Press and hold the Volume Up and Down Buttons simultaneously

until you hear a beep. The default status is Voice Connect enabled.

Receiving Intercom calls

NOTE: The Enable/Disable Voice Connect feature aﬀects both the

Intercom and the mobile phone functionality.

If you are not speaking with any one, once the other party tries to

initiate a Buddy Intercom call, the call will begin immediately.

MAKING AND RECEIVING MOBILE

PHONE CALLS

TROUBLESHOOTING THE INTERCOM:

First, make sure your microphone is located properly in front of

the center of your mouth.

PHONE FUNCTIONS

Short press the CTRL Button or speak loudly

any word of your choice.

Answer a call

Reject a call

The SCALA RIDER Q2 is designed for use in loud environments.

Please make sure to test the Intercom functionality in a LOUD

environment, such as next to an idling motorcycle.

Short press the MC Button or remain silent

for 15 seconds.

Please also verify that the headsets were paired together properly

by following the instructions in the relevant Setup sections.

Short press the CTRL Button.

Terminate a call

Voice Dial

During Standby, short press the CTRL Button

and state the name of the person you wish

to call. This feature is supported only by

mobile phones that support the Voice Dial

feature.

Setting Voice Connect Intercom preference (Primary vs.

Secondary Buddy)

The headset’s Voice Connect feature allows you to start a Buddy

Intercom call by simply speaking into the microphone. You can

deﬁne which of the two Buddy headsets you wish to connect to

when using Voice Connect Intercom.

Press and hold the Volume Down Button for

three seconds.

Redial

NOTE: The Primary Buddy has priority by default.

NOTE: If your Bluetooth mobile phone is paired to a Bluetooth GPS

device, not directly to the SCALA RIDER Q2, some of the above

Phone functions may not be compatible.

To toggle the Voice Connect Intercom between Primary and

Secondary Buddy:

When the headset is on an active phone call, any Buddy Intercom call

request will be rejected automatically.

Press and hold the Volume Up Button for three seconds and

you will hear a beep:

Once the phone call audio link drops, you can initiate and accept

Buddy Intercom calls.

• One beep – Voice Connect set to Primary Buddy

• Two beeps – Voice Connect set to Secondary Buddy

SCALA RIDER^®Q2^™MultiSet |

Turning the FM Radio On

STATUS LIGHT STATES

While no call is on the headset (either mobile phone call or Intercom

call), press and hold the MC Button on your headset for three seconds

to turn on the radio. The radio tunes in to the last radio station you

were listening to. With some phones you should wait a few seconds

after ending a call before turning on the Radio.

None

Headset is oﬀ

Alternating Red/blue ﬂashes

Mobile phone/GPS Pairing

mode

Rapid Red ﬂashes

Intercom Pairing mode

Turning the FM Radio Oﬀ

1 blue ﬂash every 3 seconds

Standby – No call is in progress

While the radio is turned on, press and hold the MC button for three

seconds to turn the Radio oﬀ.

2 blue ﬂashes every 3 seconds Call being initiated or in

progress / FM Radio ON

Switching Preset FM Radio Station

There are six pre-set Radio stations available on your SCALA RIDER

Q2. While the Radio is on, tap the MC Button to cycle between saved

stations.

1 red ﬂash every 3 seconds

Battery is low

2 red ﬂashes every 3 seconds Call being initiated or in

progress / FM Radio ON and

Searching for a New FM Radio Station

battery is low

While the Radio is on, press and hold the Volume Up or Volume

Down Button for three seconds or until you hear the next station on

your headset.

Solid red

Headset is being charged

Pressing Volume Up will search upwards (higher frequency). Pressing

Volume Down will search downwards (lower frequency). Once a

station is found, searching stops and you can hear the station.

WORKING WITH THE FM RADIO

Your headset is equipped with a high-quality FM Radio receiver. This

section explains how to enjoy the functions of the FM Radio.

To save this station, refer to the following section.

To continue searching, press the Volume Up or Volume Down Button

again for three seconds.

The SCALA RIDER Q2 enables you to listen to FM Radio while you

are not receiving audio from another audio source.

You may still continue to listen to the current unsaved station.

Pressing the MC Button in this case will switch to the next saved

station.

While listening to the radio, you do not have to worry about missing

any calls, as the headset automatically mutes the FM Radio and

switches to Bluetooth headset operation when an incoming call is

received, or when you decide to initiate a call. When the conversation

is over, the headset automatically tunes back in to the FM Radio.

Saving an FM Radio Station

The FM Radio is equipped with a memory capacity of six stations.

| SCALA RIDER^®Q2^™MultiSet

• Select the station you wish to replace by tapping the MC

button until you ﬁnd the station you want to replace.

SUPPORT

For additional information please visit our website at

www.cardosystems.com

• Search for a new station as described above.

• Tap the MC Button within 20 seconds of ﬁnding the station to

save the current station.

FAQ: www.cardosystems.com/faq

or contact us at:

[email protected]

If you don't save the station, the Radio will exit search mode without

saving the current station. You can still continue to listen to the

current unsaved station. Tapping the MC Button in this case will

move to the next saved station.

Phone:

USA and Canada – + 1-800-488-0363

International – +4989 450 36819

USING THE MP3 PLAyER WITH yOUR

HEADSET

NOTICES

Your SCALA RIDER headset can be connected to an MP3 player/audio

device by simply plugging it to the Helmet Clamp’s jack with the

audio cable as follows:

Federal Communications Commission (FCC) Statement

15.21

You are cautioned that changes or modiﬁcations not expressly approved by the part

responsible for compliance could void the user’s authority to operate the equipment.

1. Power on the headset to have it on

Standby mode, ﬂashing slowly in Blue.

15.105(b)

2. Connect one side of the audio cable

to your MP3 player/audio device’s

jack and the other side to the helmet

Clamp’s jack as shown in the photo.

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

3. Operate the MP3 Player/audio device by

using its buttons (FF/REW/PLAY/PAUSE).

Connect the audio cable to

the helmet Clamp’s jack

NOTE: Volume can only be adjusted through the MP3 Player.

• Reorient or relocate the receiving antenna.

Any other audio connection (Phone call/FM Radio/Intercom

call) will automatically mute the MP3 Player. The audio signal

will return only when headset is once again in Standby mode.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

1ꢀ

SCALA RIDER^®Q2^™MultiSet |

Operation is subject to the following two conditions:

IC RF Radiation Exposure Statement:

1) this device may not cause interference and

This equipment complies with IC radiation exposure limits set forth for an

uncontrolled environment. End users must follow the speciﬁc operating

instructions for satisfying RF exposure compliance. This transmitter must not be

co-located or operating in conjunction with any other antenna or transmitter.

2) this device must accept any interference, including interference that may cause

undesired operation of the device.

FCC RF Radiation Exposure Statement:

European CE Notice

This equipment complies with FCC radiation exposure limits set forth for

an uncontrolled environment. End users must follow the speciﬁc operating

instructions for satisfying RF exposure compliance. This transmitter must not be

co-located or operating in conjunction with any other antenna or transmitter.

The SCALA RIDER Qꢀ™ headset (the “Product”) is in conformity with the

following essential requirements of Council Directive 1999/5/EC (referred to as

R&TTE Directive): Articles 3.1a, 3.1.b and 3.2. The Product is manufactured in

accordance with Annex II of the above directive.

Declaration of Conformity (DOC)

The SCALA RIDER Qꢀ™ headset is compliant with and adopts the Bluetooth

Industry Canada (IC) Statement

1ꢃ.ꢀ1

Speciﬁcation 2.0 and has successfully passed all interoperability tests that are

You are cautioned that changes or modiﬁcations not expressly approved by the

part responsible for compliance could void the user’s authority to operate the

equipment.

speciﬁed in the Bluetooth speciﬁcation. However, interoperability between the

device and other Bluetooth -enabled products is not guaranteed.

WAIVER AND GENERAL RELEASE

By using the SCALA RIDER Qꢀ headset(s) – hereafter referred to in the singu-

lar – you will waive substantial legal rights including the right to sue. Please

read the following carefully before using the device. If you do not accept all

terms of this agreement, you should immediately return the product for a full

refund. By using the headset you agree to be bound to this agreement and

forfeit the right to sue.

1ꢃ.10ꢃ(b)

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the IC rules. These limits are designed