Altinex Car Amplifier DA103 107 User Manual

DISTRIBUTION AMPLIFIERS  
DA103-110  
DA103-107  
MANUAL PART NUMBER: 400-0449-005  
DA103-107 & DA103-110  
SIDEKICKER®  
WITH 2 VIDEO OUTPUTS  
USER’S GUIDE  
DISTRIBUTION AMPLIFIERS  
PRECAUTIONS / SAFETY WARNINGS  
1
·
This equipment has been tested and found to  
comply with the limits for a Class A digital  
device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable  
protection against harmful interference when the  
Please read this manual carefully before using your  
DA103-107/110. Keep this manual handy for future  
reference. These safety instructions are to ensure  
the long life of your DA103-107/110 and to prevent  
fire and shock hazards. Please read them carefully  
and heed all warnings.  
equipment is operated in  
a
commercial  
environment. This equipment generates, uses,  
and can radiate radio frequency energy and, if  
not installed and used in accordance with the  
instructions found herein, may cause harmful  
interference to radio communications. Operation  
of this equipment in a residential area is likely to  
cause harmful interference in which case the  
user will be required to correct the interference  
at his own expense.  
1.1 GENERAL  
·
Qualified ALTINEX service personnel or their  
authorized representatives must perform all  
service.  
1.2 INSTALLATION  
·
To prevent fire and shock, do not expose this  
unit to water or moisture. Do not place the  
DA103-107/110 in direct sunlight, near heaters  
or heat-radiating appliances, or near any liquid.  
Exposure to direct sunlight, smoke, or steam can  
harm internal components.  
·
Any changes or modifications to the unit not  
expressly approved by ALTINEX, Inc. could void  
the user’s authority to operate the equipment.  
·
·
Handle the DA103-107/110 carefully. Dropping  
or jarring can damage the unit.  
Do not pull any cables that are attached to the  
DA103-107/110.  
1.3 CLEANING  
·
Clean only with a dry cloth. Never use strong  
detergents or solvents, such as alcohol or  
thinner. Do not use a wet cloth or water to clean  
the unit. Do not open the unit to clean.  
1.4 FCC NOTICE  
·
This device complies with Part 15 of the FCC  
Rules. Operation is subject to the following two  
conditions: (1) This device may not cause  
harmful interference, and (2) this device must  
accept any interference received, including  
interference that may cause undesired  
operation.  
400-0449-005  
2
DISTRIBUTION AMPLIFIERS  
ABOUT YOUR DA103-107/110  
2
MECHANICAL  
DA103-107  
Material/Color  
Height  
DA103-107/110  
DA103-107/110  
SIDEKICKER WITH 2 VIDEO  
OUTPUTS  
Steel/Silver  
0.78 in (20 mm)  
4.23 in (107 mm)  
1.74 in (44 mm)  
0.38 lb (0.17 kg)  
Width  
Depth  
The DA103-107/110 provides  
transmitting computer or component video to two  
different displays from a single computer.  
a
means of  
Weight  
DA103-110  
Material/Color  
Height  
ABS Plastic/Black  
0.92 in (23.4 mm)  
4.25 in (108 mm)  
1.68 in (42.7 mm)  
0.16 lb (0.07 kg)  
The DA103-107/110 is compact and easy to use.  
It offers a female 15-pin HD input and 2 female  
15-pin HD output connectors.  
Width  
Depth  
The Sidekicker is capable of being powered from  
one of three different sources. The first uses the  
+5V on pin 9 of the computer’s 15-pin HD video  
connector (VESA standard). If the computer or  
video cable does not provide power to the  
DA103-107/110, then the second option obtains  
power from the computer’s USB port if available.  
The video cable provided with the DA103-107/110  
has a USB connector on one end for use with this  
option. If there is no USB port available, the third  
option is to use the +9V adapter.  
Weight  
DA103-107/110  
T° Operating (T° Max)  
Humidity  
10°C-35°C (50°C)  
90% non-condensing  
40,000 hrs  
MTBF (calculations)  
Table 2. DA103-107/110 Mechanical  
ELECTRICAL  
DA103-107/110  
Input Video Signal  
Analog Signal Level  
Impedance  
1.0 Vp-p max  
75W  
TECHNICAL SPECIFICATIONS  
3
Input Sync Signal  
H & V SYNC  
Specifications are subject to change.  
See www.altinex.com for up-to-date information.  
TTL  
Impedance  
10 kW  
FEATURES/  
Output Video Signals  
Analog Signal Level  
Impedance  
Output Sync Signals  
H&V Sync Levels  
Impedance  
DA103-107/110  
DESCRIPTION  
0dB +/- 0.3dB  
Inputs  
75W  
Video  
15-pin HD female (1)  
2.5mm DC jack (1)  
Power  
TTL  
Outputs  
75W  
Power  
RGBHV/YPbPr  
Compatibility  
15-pin HD female (2)  
Computer/USB Port (+5VDC)  
+9V Adapter  
140 mA  
(0.7 W)  
150 mA (1.35 W)  
Video Signal  
Resolutions  
VGA through UXGA,  
480p through 1080i  
640x480@60Hz  
250 ft (76 m)  
Accessories Included  
Video Cable with USB  
2 ft (0.61 m)  
9 VDC, 1 A  
6 ft (2 m) min.  
VGA:  
Max. Cable Length  
(using ALTINEX cable  
CB37200MR)  
Power Adapter  
UXGA: 1600x1200@60Hz  
200 ft (61 m)  
Table 3. DA103-107/110 Electrical  
Table 1. DA103-107/110 General  
400-0449-005  
3
DISTRIBUTION AMPLIFIERS  
PRODUCT DESCRIPTION  
4
DA103-107  
POWER 9V, 1A  
POWER/SIGNAL PRESENT  
RED = POWER  
GREEN = SIGNAL PRESENT  
VIDEO INPUT  
VIDEO OUTPUT 1  
VIDEO OUTPUT 2  
DA103-110  
POWER 9V, 1A  
POWER/SIGNAL PRESENT  
RED = POWER  
GREEN = SIGNAL PRESENT  
VIDEO INPUT  
VIDEO OUTPUT 1  
VIDEO OUTPUT 2  
400-0449-005  
4
DISTRIBUTION AMPLIFIERS  
APPLICATION DIAGRAMS  
DIAGRAM 1: TYPICAL SETUP  
5
The DA103-107 is shown in the diagram below, but  
both the DA103-110 and DA103-107 have the save  
functionality.  
400-0449-005  
5
DISTRIBUTION AMPLIFIERS  
DIAGRAM 2: INTERNAL VIEW  
The block diagram for both the DA103-107 and the  
DA103-110 is shown below.  
SIGNAL  
POWER  
DETECT  
POWER  
2.5mm  
9V, 1A  
R1  
G1  
R
G
VIDEO  
15-PIN HD  
OUTPUT 1  
VIDEO  
15-PIN HD  
B
B1  
INPUT  
H
H1  
V1  
V
PLUG AND PLAY  
R2  
G2  
VIDEO  
B2  
15-PIN HD  
OUTPUT 2  
H2  
V2  
400-0449-005  
6
DISTRIBUTION AMPLIFIERS  
INSTALLING YOUR DA103-107/110  
6
OPERATION  
The DA103-107/110 requires no adjustments for  
proper performance. Once set-up, the  
DA103-107/110 will work trouble-free without user  
intervention.  
7
Step 1. Connect the input of the DA103-107/110  
to the video output of the computer using  
the cable provided. The Signal Present  
LED should be on. The LED will be red if  
there is power and green if a video signal  
is present.  
TROUBLESHOOTING GUIDE  
8
We have carefully tested and found no problems in  
the supplied DA103-107/110. However, we would  
like to offer suggestions for the following:  
NOTE: The  
DA103-107/110  
derives  
power from the video output  
connector of the computer. If the  
computer does not supply power  
at the video connector, it is  
necessary to connect the USB  
connector (from the video cable  
provided) to an unused USB port  
on the computer. If there is no  
USB port available, proceed to  
Step 2 and use the external  
adapter.  
8.1 THE LED IS NOT RED.  
Cause 1: There is no power.  
Solution: Verify  
the  
DA103-107/110  
is  
connected to the proper power  
adapter or USB port.  
Solution 2: Make sure the adapter is plugged  
into a working outlet and that power  
is on.  
Step 2. Skip this step if the LED is on.  
Cause 2: The cables are loose.  
Solution: Verify the power plug from the AC  
adapter is plugged all the way into  
the DA103-107/110.  
Connect the DA103-107/110’s power jack  
to an AC power adapter and plug the  
adapter into a working outlet.  
Cause 3: The  
DA103-107/110  
has  
a
Step 3. If the power is on, the LED on the  
DA103-107/110 should be on and red;  
green if a signal is present.  
problem.  
Solution: If there is still no power, the  
DA103-107/110 may require  
Step 4. Connect VGA-type cables from the  
15-pin HD output connectors on the  
DA103-107/110 to the display devices.  
service. Please call ALTINEX at  
(714) 990-2300.  
Step 5. The DA103-107/110 is now operational.  
Verify the picture quality on the receiving  
monitor is equivalent to the quality as  
displayed on the local monitor.  
400-0449-005  
7
DISTRIBUTION AMPLIFIERS  
8.2 THERE ARE NO REMOTE IMAGES.  
Cause 1: The source has a problem.  
ALTINEX POLICIES  
9
9.1 LIMITED WARRANTY/RETURN POLICIES  
Solution: Connect the output of the computer  
directly to each monitor and verify  
the quality is good. If the images are  
good, see Cause 2.  
Please see the ALTINEX website at  
www.altinex.com for details on warranty and  
return policies.  
9.2 CONTACT INFORMATION  
ALTINEX, Inc.  
Cause 2: Cable connections are wrong.  
Solution: Verify  
the  
input  
of  
the  
592 Apollo Street  
DA103-107/110 is connected to the  
output of the computer using the  
cable provided.  
Brea, CA 92821 USA  
TEL: 714 990-2300  
Solution 2: Verify that the Signal Present LED  
on the DA103-107/110 is on and  
green. If the LED is on and green,  
check the connections from the  
receiver to the displays.  
TOLL FREE: 1-800-ALTINEX  
Solution 3: If the LED on the DA103-107/110 is  
red, there may be a problem. Please  
call ALTINEX at (714) 990-2300.  
400-0449-005  
8

Bassworx BS Speakers BS42 User Manual
Casio fx 991ES PLUS User Manual
Cerwin Vega Heavy Duty Professional Amplifiers CV 900 User Manual
Hamilton Beach Classic Chrome Blender User Manual
Hamilton Beach liquid blu 59205 B42 User Manual
HP (Hewlett Packard) Compaq LE1911I User Manual
Imperial Range IR 24BR 120 User Manual
Jensen Car Stereo System CD3720XM User Manual
JVC 0206ASR NF VM User Manual
JVC GR SXM72ED User Manual